I have had my washer and dryer for about 5 years. After a couple of years, I noticed my washer would fill and stop. When I go to put clothes in the dryer, it’s still filled with water... very inconvenient! I have to open and close it and then it continues. The dial doesnt work properly! The delicate cycle hardly works... that started after about a year. It just freezes up and stops. I have to open and close it. It does not rinse right, leaves a film on dark clothes, and I have to rinse again; I do not over fill it either. Sometimes it does smell a little mildew.The dryer knob does not work properly. I set my setting and pull the knob out, and it doesnt come on. I have to do it several times or change the setting or put it on 30 minutes only... very frustrating! I never had these problems with my Kenmores! I wish I did not switch brands. These things should work properly. I realize washers and dryers dont last like they used to, but come on! They also cost so much more than they used to. I wont do this again. I will do more research as to what is a good product. Too bad!

Purchased my Maytag Bravo MVWX500XWO 4 years ago. While still under warranty I had to call for service once. I felt based on the Maytag reputation I didnt need to extend the warranty. WRONG!! My Maytag first started with the loud and fast spinning. Like it was about to explode! Then my washer started leaking. I thought I was having plumbing problems, so I called a plumber... wasnt the plumbing. My washer wasnt draining out completely so I finally called an appliance repairmen who immediately knew what the problem was ($109.90) for a 15 minute review. The leak was from the bottom of the washer... the seal around the transmission cracked, broke or whatever causing water to drain out in my garage. Also the main control board wasnt working. Repairman said it would cost me $700 to repair!! Really?!! My machine was practically new! Without hesitation the repairman said for me to call the Whirlpool/Maytag 800 number and they would offer me another washer for 50% off at their online outlet. Repairman said this always happens... Why would I want another Maytag or Whirlpool!! Please do not buy the Maytag Bravo... Can you imagine if this happened with a car purchased... 4 years and then having to buy another car??!! Not reliable or worth your money!!

I would not recommend the Maytag washer with the large tub. It does not clean your clothes. I called Maytag and they do not care as long as it uses as little water as possible! Not a good value for the money!! That was the first time and last time I buy a Maytag... Thats the last $5000 they will get from us!

Purchased new Maytag Refrigerator from Mannys in Western MA. Top freezer, over $900.00. Never has worked correctly. We need to turn the freezer way up to freeze the ice cream and it forms frost all around the freezer with mini icicles hanging! But even worse... no matter what setting you put the refrigerator on it ruins your food by freezing everything. The only safe spot is in the deli drawer. I have thrown away hundreds of dollars worth of food that is destroyed because it froze in the refrigerator.A service man from Mannys came and ordered parts. He came back and said they were the wrong parts. Now he says that the refrigerator has a problem and Maytag is trying to come out with a plan on how to fix it. I talked with Maytag (took 44 minutes to get someone on the phone). The manager in service was rude, said they dont replace food and they would work on fixing it. 2 weeks later... no calls from either place. I called Mannys and they said they should have some news by next week. In the meantime I dont have a refrigerator that works! NEVER BUY A MAYTAG REFRIGERATOR!!! It is still under warranty and I asked for a new refrigerator... both Mannys and Maytag said no way.

The steam/heat produced by the oven has made the electronic (digital) control panel buckle. Yes! This is a thousand-dollar (plus) stove, and it has warped, through no fault of mine. When I want to cook something, I press the keypad to enter the number of cooking degrees that I want. The problem is, the control board is not working correctly. Regardless of my typing in 350, it will default to 100 degrees and stay at 100.As a teacher, I do not have a huge income. I was disgusted with my recent repair estimate of $80 for a service call, and a quote of over $600 for the replacement part, plus some not-yet-determined labor installation costs. Calling the 800 phone number for Maytag connected me to some local people working as independent and overpriced contractors in Los Angeles, California. They are not MAYTAG employees, so they are not well-informed about the product.I miss the time when manufacturers stood by their products, and had factory-trained and authorized employees available to make repairs. I bought this monster Maytag stove from Lowes. I am disgusted with both companies. I have gone online to research buying my own part and hiring a local yokel to put it in. Most everyone I have encountered has been a rip-off artist. I am teaching your kids and grand kids to read and write, and you dont want to help me repair my stove without price-gouging. I can use the burners to some stove-top cooking. Life has become a hassle without being able to cook.

Re: refrigerator model # MBF2258XEB1. The above-referenced refrigerator was purchased in 2011 from Home Depot. We paid over $1,000.00 thinking we were buying a good product. Right now the bottom freezer is working but the refrigerator is not cooling. An appliance repairman cleaned out the defroster part, but that did not resolve the problem. He said it was a compressor/valve gas line problem. I cannot afford to spend hundreds of dollars to have this repaired. Even though the warranty has expired, I believe that Maytag should pay the cost of the repair. This is VERY inconvenient and frustrating.

Our Maytag French Door with freezer on Bottom MFF2258VEB quit on us after three and a half years. Called local authorized Maytag dealer. They sent out a repair man. He said the main control board was bad! After much discussion we told him to replace it. After part and labor $261.00 it is running for now. Then called Maytag to see if they could reimburse us for the part $161.00. NO DICE! I have a kitchen full of Maytag products and a washer-dryer set but will not BUY ANY MORE Maytag products. Pass the word to boycott all MAYTAG PRODUCTS!

We purchased a Bravo HE washer about a year ago after our old Maytag finally died after 17 years. Our new one is more quiet, does a good job with less water although the cycle times are a bit longer.

I am writing to tell you the dishwasher sold to my family malfunctioned as a result of an apparent design flaw. I also ended up wasting an entire day for a service person who never arrived. On October 14, 2009, my family bought a Maytag Dishwasher (model #MDBH979AWW) from Home Depot. It had run beautifully until last week, when the left-hand side of the control panel went dead. I then called the Maytag service number (800-688-9900) listed in the instruction manual and scheduled an appointment with the A&E Factory Service vendor for the following Friday (July 6th, 2012) between 8:00AM and 12:00PM. Around 12:30PM, no one had arrived, so I called again. I was told by the agent that the technician was en route and would arrive at my home in forty five minutes. At 2PM, still nobody arrived. I rang again when I was then informed that my name had been strangely kicked out of the system and made available for a reschedule. Wanting to stick with a Maytag-approved business, I went ahead and scheduled the next earliest appointment available, Monday, July 9, 2012. The technician from A&E Factory Service that actually did show up reported that the entire control panel had to be replaced at a cost of $281.48. Interestingly, he added that he had seen other Maytag dishwashers with this exact same problem and recommended that I wait until the water settled before adding extra dishes during a cycle since water apparently leaks into the electronics via a small gap on the top of the inside of the door. Of course, there is nothing in the instructions warning against such.I chose to fix the machine since I didnt have the money to purchase a new one. Are your dishwashers designed to last only a few years? I truly believe that I have been duped by Maytag since this problem resulted from a design flaw. I am asking you to please look into these matters and correct any wrongdoing that you see fit. Copies of receipts for the dishwasher purchase and service repair are enclosed.

Wish I had read the reviews! I have had Maytag before and they were awesome. New purchase is horrible! Doesnt clean the clothes, leaves a residue on clothing and dryer does not dry properly. Called Maytag and they said use Affresh. Spent $10 on a pack of 5, and it did no good. My dark clothing is getting ruined! The washer is also incredibly LOUD! Very disappointed in this company and would never recommend them to anyone! I had purchased at Lowes, but had a delayed delivery, so I cant take them back, or I would.

We purchased our Maytag through Sears. We wanted a very basic machine, and thats what we found at Sears, yay! Fast forward eight years and it suddenly quit agitating. We tried fixing it ourselves by replacing a plastic gear part, which, later on our appliance technician said was totally logical, but it still wouldnt work. We got our appliance repairman out here and he took it into the shop and fixed the problem, which turned out to be part of the motor or something like that. The thing that bothers me the most is that he asked if we had bought a refurbished washer, but we hadnt, it was brand new. He gave us a part that was swapped out that wasnt made for the machine and also said the safety guard for the cord was missing. This keeps it from pulling out of the machine in case it gets jerked. I feel deceived and just wanted to vent because there really isnt anything I can do about it now. Buyer beware, yes, but I know we have to be our own technician sleuths to be sure were getting what we paid for?

I bought the Maytag stainless steel refrigerator with the top double doors and bottom freezer. I paid $3000 for this thing and the ice maker has broken twice, an ice sheet forms on the bottom of the freezer and the drawers broke due to being cheaply made with plastic. I had the old style refrigerator for 15 years with not one problem. I think these newly made appliances are made crappy! Will never buy a Maytag again!!!!

I purchased the microwave less than two years ago. I noticed the display panel would not always work a few months ago. This is part of the control panel that shows time, etc. Called Maytag just now & they told me that the control panel is starting to fail. I could purchase a one year extended warranty for $289!!!Are you kidding me??? The part alone would be around $160. What has happened to Maytag? I thought they had a good name. :( Very disappointed.

We purchased a Maytag convection oven less than a year ago! Today is the 3rd time the heat sensor has gone on it! I want a new stove! I am beyond disappointed with the business and the product! Have always bought Maytag! Rethinking it now!!!

We purchased Maytag Dishwasher MDB5601AWW/46171101NP when we built our new home. In the last several months, water was leaking out onto the floor. We called Maytag and they told us there was a recall on the heater element and that they would send the part out. We made sure they knew the reason for our call--TO REPLACE THE GASKETS!. Maytag contacted a local authorized repair person. When they called to set up appointment, my husband reminded him about the gaskets. The guy showed up without gaskets, saying Maytag didnt put it on the order! We called Maytag to set up another service call. The guy showed up again today without the gaskets. We were told they had to be ordered and that he would have to come out again! Three service calls for one issue! Aside from this, the circuit board has never worked right. We push the correct buttons, but never know what kind of cycle we will get. We learned to live with it. Our bottom racks are melted as well as the sides of the dishwasher. Now that we know about the heater element being defective, this may be the cause of the bad gaskets and melted racks. It will cost almost $300 just to replace gaskets, and yes, we have to pay a service call for it when it could have been done in the first place. We called Maytag to complain and were told that replacing the gaskets always takes two service calls--one for diagnosis and the second to put in part. They said they dont take the customers word for it when we tell them whats wrong!

I purchased a Neptune front-load washer in November 2005. Now that its out of warranty, theres nothing that Whirlpool can do for me. The front panel of the washer that surrounds the door has been rattling for a few weeks, so my husband took it off and found a crack on the top right section of the panel where its bolted to the frame. There is a rust bubble where the crack started. We couldnt see any of this until he took it apart. The cost of a new front panel is $185 and the response from Whirlpool? They are “very sorry” that this has happened, but there is nothing that they can do. Oh, really? Well, I come from a long line of Maytag owners and there is something I can do: spread the word about the disgusting piece of junk I paid $1,100 for! This washer wasnt even made here - it was made in Korea and its not worth $100! Note to Whirlpool: your customer service sucks!

Maytag bottom freezer, 4 years old, ice forms on bottom of freezer. Water melts all over floor every few days. Please add my name to class action suit if/when one comes.

Im currently standing in front of my washing machine waiting for the 13-minute drain and spin cycle to finish because once again my load didnt drain and finish right. Except it has already been 40 minutes and it claims there is still 9 more left as it continues to sit there doing nothing while it hasnt even started spinning yet. It Sat on 13 minutes while sensing for over 5 minutes, then 12 for 10 minutes while doing nothing, then it changed to 11 minutes and made some weird noises but didnt actually do anything for 15 minutes, and now the timer randomly changed from 11 to 9 without any noises or movement happening and now continues to sit here.I stupidly thought I could spin my clothes real quick to throw them in the dryer before bed and now I stand here extremely tired and very irritated. I also have no doubt some of the clothes will have holes in them when theyre done because they always do, my family looks like were homeless and ratty half the time we get dressed now. Also it never deep cleans thoroughly even on the toughest settings, I swear our socks can be washed 3 times in a row after being soaked all day and still come out crusty or a lot of times the armpits of shirts will still smell or be ultra stained with deodorant marks still.This technology is almost too advanced and everything is decided by sensor, regardless of the registered functions on the buttons it will still do what it wants as the sensors see fit and run when they decide everything is perfect and ready, including taking 10 minutes just to unlock the lid when you pause a load cuase a small child may drown in the foot of water or a person may have their life completely altered by getting a little bit wet if the machine isnt completely drained and in pristine condition before you open the door. This machine is terrible. This company is terrible. And worst of all they drain your wallet for these horrible contraptions. I wish I could rate this 0 stars.

I purchased this machine (MVWB765FW0) because I had a good experiences with Maytag in the past. There is a manufacture defect in this particular machine. If I were you, I would not buy it. I’ve lost two sets of bedsheets and my wife had a dress that she loved that got ripped up at the bottom between the agitator and the base of the machine. Maytag knows about the problem and does not have a solution.

This has the aqua cleaning technology, sounds real good. DOES NOT WORK! The cleaning is done by you as you nearly climb into the oven with a plastic scraper which they supply to scrape prior to the cleaning cycle. Then after you have used the distilled water in the bottom of the oven during the cleaning cycle (steam), you climb back in to wipe out the water and use something similar to a magic eraser to SCRUB the oven.Here is the real kicker....during the cleaning process, in between the glass (in the door) you develop water spots that cannot be cleaned unless you pay to have a service technician come out and tear it a part to clean it. According to Maytag THIS IS NORMAL and is proven (by their engineers without any documentation for the customers to be able to see) to be normal?? The consequence is a brand new stove will never be clean and it is the first thing you see when you come into my house. I AM EXTREMELY DISAPPOINTED!!!!

This new refrigerator, which was delivered to my house on 9/20/17, is so loud that I cannot have a conversation in my kitchen. It is supposed to be energy efficient. I do not know how that is possible as it runs 50 out of every 60 minutes. I contacted their customer service about this appliance. They repeatedly put me on hold or disconnected me. If I could give lower than one star, I would. Learn from my mistake - dont purchase from this company.

I bought my Maytag Dishwasher (mdbh979aww3) about two years ago and just last week, the control buttons on the right stopped working. I see on this site that someone else had the same problem and explained that the wires got corroded, so now Im not sure I even want to replace the part when it only worked for 2 years. Now Im stuck buying a new dishwasher.

Our home has seven Maytag appliances: an upstairs kitchen, downstairs suite and laundry room. All were brand new six years ago and what we thought to be good quality by the price we paid for them. We have lived to regret ever dropping a cent into Maytags business account, as we have had nothing but trouble with them. We dont have small kids or teenagers abusing them. Its just us and a very responsible single adult downstairs. And every time we turn around, one of them is costing us nothing but money and grief. Our first problems began with our upstairs fridge when it was only two years old. At that time, it cost us $400 and since then, it just goes on and on. Last week, our downstairs fridge quit, and today, our upstairs one quit. We have had work done on our range, as well as our washing machine and dishwasher. If you are thinking of buying a Maytag appliance, dont, unless you like to throw away your money. I couldnt believe when I looked up Consumer Reviews on Maytag appliances tonight that I would find only 1 out of 5 stars, and read all the terrible reviews written by angry consumers. Well, add me to the list because I will never buy another appliance from Maytag again, and am beginning to think its time to sell this house to get rid of these stupid, useless, pieces of ** Maytag appliances! Sorry, people, but I cant afford to keep replacing them!

Purchased this Maytag microwave brand new on April 2017. In January 2019 began to have issues with the display reading open/close door. Maytag would send a repairman for $160 to take a look at the problem. Parts of course are extra. I will never buy a Maytag product again.

The washer is designed to use low amounts of water. The top is glass so you can watch what is or is not happening. The manual states there should be clothes above the water after filling. However after the wash cycle with a full or even half full washer, there is still some dry clothes above the water. As a result the clothes are not washed until the rinse cycle. I called Maytag and a repair tech came out to fix it. His solution was to trick the sensors by dumping a pail of water on top of the dry clothes before starting the washer. The sensors think there are more clothes than there really is. Will never buy another Maytag or Whirlpool product again.

I have had my Maytag set for shy of 2 full years, of actual usage time, that is. My dryer seems to be functioning normally, minus an occasional lengthy cycle time, even after the clothes are dry. The washer however, is sitting in my garage now. F51 error code, which online told me the rotary position sensor was the issue. Yes, I was told by an A&E repairman, who was at the house for an unrelated repair, that it was the bearing that was bad. When he showed me what I was looking for, there was the bearing laying in the clear plastic housing, in the underside of the washer. Its going to cost around $350.00 to get the part, if it can be found, and the service call. No, not really worth wasting more money on it. I am very unsatisfied with this unit. With 4 kids and 2 adults at home, I expected much more from the Maytag name.

We were very impressed with this dishwasher when we bought it about 2 years ago. It looked very nice, it was the quietest running dishwasher weve seen, dishes came out sparkling. However, the nightmare quickly began. It started with having to cancel then resume. It ran for 8 hours non-stop (still cycling the next morning). We unplugged it and we were able to use it normally for a few times. Weve had so much aggravation with this machine weve decided to (A) Never to buy another digital dishwasher, (B) Join the class action suit proposed against Maytag. We have tried all the reset solutions offered and Weve been hand washing dishes (again) for days.

Have had this set for about three years (was a gift from my parents on having our first child), and its horrible. Clothes come out partially dry, with NEW stains on them, torn or frayed, and twisted into knots. Its supposed to be a high-efficiency washer but we often have to wash things twice to get them clean. We now have two little boys and Im starting to save to buy a different set (no Maytag ever again); disgusted that I cant even sell this set in good conscience. Will either be a donation or an eyesore for the landfill. Worst $1100 ever spent.

We owned the washer for 2 years and 2 days when we got a code F70. After searching online, I found hundreds, if not thousands, of reviews and self-help forums that show this product is in dire need of a recall. The problem I had is the motor control unit (MCU), which is a $225 to $275 part online. However, Maytag will only replace the board under extended warranty with a refurbished board that they say costs $330, whereas they say the new one is over $600. Why is it that Maytag charges double what everyone else charges? If so many people are having these problems, it is obviously a defect and should not be the consumer’s responsibility. It is obvious that this is too common of a problem.

I have bought a new Home Depot Maytag Impeller HE washer. After 6 repeat washings of 2 items that are lightweight dark brown it was obvious after drying they had soap and lint and lot hairs on it. I reached with no he detergent. The last 4 times the water level filled to 1 depth even for high level water setting to extra rinse or power wash settings. I went to Home Depot and they suggested I call Maytag repair center on Tuesday after the labor day holiday to have them check it out. I will also call the supervisor at Home Depot as I do not feel paying $600 for a faulty machine is acceptable.

The Maytag Dishwasher Model MDBTT50AWW started having problems cleaning dishes after about 3 years. I usually had to clean them first before placing in the washer. About 6 months ago (5 years of owning), some of the control panel buttons stopped working. Finally, the Start button stopped. Replacement part and service is about $400 per local appliance repair shop. They recommended buying a new dishwasher. They stated that the touch control panels have reduced the life of dishwashers to about 5 to 7 years. However, I had seen testimonials on the web of dishwashers lasting on average 9 years - not Maytags. I will be avoiding Maytag for next purchase. I have seen too many complaints online about the control panels dying. I consider myself lucky as my panel died after 5 years while many reviews say theirs died right after the 1-year warranty.

I purchased a 5 Maytag appliances in the last year. Stupidest thing I have ever done. The clothes washer being the worst. Front Load, model # MHW3505FW1. Last night I threw 5 small, lighter weight things in the washer on normal cycle, med temp, max extract... like usual. An hour and thirty-eight minutes later (normal cycle time), I opened it to find most things never even got wet. One scarf was still folded in fourth - the way I put it in! I called service even though I know there is nothing wrong with the washer, other than being so poorly designed, it cant get clothes wet with a damn tub and a hose. After I told her the problem, she puts me on hold, comes back to tell me she researched this everywhere and she found that this is a symptom of a NEW washer! Its SOO efficient that you cant even tell it was wet! Bull. Most of the items were brand new and you could see the original creases and smell the new smell. They CLEARLY were never wet. They wanted to set up an appointment for servicing, so now I have to be here for them to tell me nothing its not broken. I will never buy another Maytag again.

My stove has been reliable and efficient. I bought it about 11 years ago and it looks nearly new. I have a gas range with 2 ovens. The top looks scratched a bit from just cleaning. The only negative is the top which has some scratches if you look closely and when I first got it, I had to have an oven gasket replace. Still I feel it was a good purchase.

Purchased a Maytag Bravos top load washer and dryer in May of 2011. We had our other Maytag washer and dryer for 14 years, and they were working fine when we sold them. We saved a year for a new one. We spent $1,700.00 for them both. We assumed they would last as long as our old ones. Been buying Maytag our whole lives. Besides the clothes not getting cleaned. Besides the washer smelling, even after we clean it regularly with the product proposed. Besides it not working on the normal function. Besides it shredding our clothes if you put it on the highest spin speed. It started to make a very loud noise. Like an airplane taking off. Called a friend of ours that use to have an appliance store in Fenton, Michigan for decades. He said it was the bearings and that You have to replace the whole tub. A $300-$400 fix. And that it would do the same thing again in a short period of time. He said that they are junk.We would be better off buying a new one. He said, The ONLY one you can buy now that will last like they use to is Speed Queen. I had never heard of them. They start at about $750. But they are worth it. He said that they dont make any washers to last more than 3-4 years anymore. We will NEVER buy Maytag again. And Sears wouldnt give us the time of day. Each time we called and asked to be switched over to the recall department, we just got a busy signal, then a fax machine noise. We have shopped at Sears for years. Boy, loyalty doesnt mean anything in this day and age. Im sure Speed Queen will be happy to help us out. DO NOT buy any Maytag products. There should be a class action suit against them for this. There are thousands of us that got ripped off. I cant tell you how upset my husband and I are about this. We are retired, and on a fixed income, and I am disabled. The stress this has caused cannot be put into words.

Why is it when you wash dark clothes they come out with white spots which looks like soap. I have put very little soap and it still appears. I usually wash in cold water so I tried warm water - same result. I have had a Maytag for a least 40 years never had this problem - what is it I am doing wrong? I have to wash and rinse at least 2 more times. I would appreciate a answer so I can fix this.

I purchased a Maytag Dishwasher at $600. 6 months after installation, the control panel quit. Maytag sent a repairman and replaced the panel. 4 months later, the control panel quit again. The repair man told me that if it failed a third time, that Maytag would replace the dishwasher all together. The control panel quit again just a few days before the warranty expired. When the Maytag repairman came for the repair, he tried to convince me that it was not the control panel this time. He then replaced the control panel, but did not use the embedded electrical connectors. He literally cut the wires and wired it together by hand, wrapping everything in electrical tape. He said this was a different repair than the others and the three strikes and a full replacement rule didnt apply. I wasnt convinced and called Maytag to complain. I was promised a six month warranty extension, if I would accept the repairs. Two months later and the control panel has quit again. When I complained to Maytag, I was told that I had no six-month warranty extension and it had never been promised to me. They offered to send a repairman to diagnose the problem for $130. Needless to say, there will NEVER, and I repeat NEVER, be another Maytag appliance bought for my home.

We purchased a $500.00 Maytag dishwasher, Model #MDB7749SBW, in August 2013. In December 2014, a little over a year of owning it, the pump failed. We called Maytag and they had a service company come out and replace it. We paid $181.00 for this service call. In July 2015, the control panel failed so we called Maytag to see if they would replace it at their cost. All they are willing to do is to send another service guy out at our expense. The service call is $89.95 and that doesnt include the labor! The total with tax will be close to $200.00 again!!! Now we are getting close to spending $1,000 for this piece of junk! In addition, this dishwasher is only used three times a week because there are only two people living in our household. It is obvious after reading the other complaints that the control panels are defective and I am sure that Maytag is well aware of this issue. So, buyer beware. Dont even consider purchasing a Maytag dishwasher unless you enjoy watching your money flush down the toilet. They dont even deserve a 1 star rating!!!

I purchased the Maytag Bravos top load washer and the matching dryer at Home Depot back in 2009 after giving my son my very old Maytag washer and dryer that was running just fine. I liked the top load energy efficiency idea of the new Bravos and the large capacity of both the washer and dryer. Also, the Maytag name sold me, gave me confidence I was purchasing a quality product... WRONG. When it was delivered, there was damage to the dryer door, so a new one was ordered and mailed directly to me. Once it came in, I called to have someone come put it on. First issue, not a really big deal but disappointing.About one month into using the dryer, the top of it became so hot it could literally burn your hand. There was also an error message. I had purchased a one-year warranty, even though technically there is a manufacturers warranty on the product. A part had to be replaced in the panel. This happened twice. We then moved out of state for one year and the washer and dryer stayed in storage unused during that time.Fast forward to 2014 and the washer will not complete any cycle except the spin cycle. I keep getting an error message of OL which means overload. The machine is NOT overloaded. It literally takes me hours to get through one cycle of washing clothes. And they dont even come out clean. I called Maytag repair and they offered me a one-year warranty for $363.75 since the washer is having issues. They explained to me if its the control panel the cost alone for that is $383.00 not including labor. Also, the dryer take forever to dry. I have to run each load through a cycle twice to dry everything. So much for the energy efficiency of these machines. At this point, I am considering just buying another washer, something cheaper without all the fancy bells and whistles. I am terribly disappointed in Maytag.

This washing machine is TERRIBLE! If I could give it zero stars I would. It broke right after the first year and has been nothing but trouble since. Agitators has been replaced twice. Clothes do not get clean. Do not buy this machine. When I contacted Maytag with my initial complaints they were not helpful. Please save yourself the trouble and buy a different brand machine.

Our experience with our Maytag refrigerator has been anything but good! It has the model # and serial # of the ones that have been recalled, only we have just found out about this. We bought this new at Sears. Soon after, it started having troubles with the freezer, would freeze up and the whole thing would stop working. Over the years, we have had repair after repair, money after money. Just for the record, my husband and I about every two weeks spend about one hour defrosting this monster! It looks nice on the outside.

Christmas sale, needed a washer. Had a great experience with Whirlpool Duet so went for the on Sale Maytag Bravo MCT. No agitator which I thought odd. Bought the warranty. Did no good as soon as I hauled the washer home (3-hr trip one way). It wasnt washing my clothes clean. Hubby said try different cycles and soap and temperatures but at 8 months pregnant it wasnt long when I didnt fight with the machine but focused on a very busy life. Baby number 7 and I didnt care how the clothes washed as long as they didnt stink. Well baby is older, the warranty is not over and after much dialoging, no one will do anything for me. I put muddy pants in, they come out muddy. I put cloth diapers in, they come out smelling like pee. How hard can it be to come up with a machine that just turns clothes round and round with a little soap and water? Apparently really hard as Maytag failed to test this machine. Maybe city folk just have lightly soiled but on the farm with 7 kids, my kids play hard and their clothes are very dirty. They continue to stay dirty unless I wash them twice on Power Wash and Extra Heavy Load. Not impressed. Would like a replacement washer of equal or lesser value, anything that works. Oh P.S. I have the receipts and order number. Sorry its not put online to be verified buyer but dont feel like digging for paperwork at the moment.

I bought a Maytag refrigerator from Lowes. It has the freezer on bottom and I cannot put no fruits or vegetables in my refrigerator - it freezes them solid. Will never purchase this style of refrigerator again. Very Unsatisfied with this product

I related my problems with a Maytag Bravos Washer a few days ago. A year and a half after I purchased the washer, it would no longer spin, among other problems. I was persuaded to call a repairman who diagnosed faulty electronic components which would cost me nearly $400 to repair. He confirmed that the washer was poorly built and strongly advised that I replace it. So, after paying him only $25 for a service call (he felt sorry for me), I did some research and bought a top-load agitator washer because the old-fashioned machines actually do their job - they wash clothes! I was duped by the high-efficiency claims, low-water-usage of the Maytag which didnt wash that well when it did work.

Gave up a very good old washing machine to update to a newer one and so we got the Maytag bravos 300. I thought Maytag was a very dependable name and product. The warranty went out. 2 weeks later, the water pump went out. I had to pay to have it replaced. Then after that it started making noise that got louder and louder and now it sounds like a thrashing machine. And now it has started leaking water out of the bottom. So its going in the scrap pile. What a loss of money - the worst investment I have made. For what I paid for this machine, it should have lasted for many years to come. The washer I had before this Maytag I had for 16 years - no problems at and it still worked great when I gave it away. Maytag use to be a brand you could count on. Great craftsmanship has been taken away and monetary gain has taken over. I hope no one else has to go through this nightmare that I have. Maytag they should have to give peoples money back that we all worked hard for. Going with a LG now, hope its a good machine.

Maytag Cenntenial Washer - We traded our super capacity for the ex-large Maytag washer and we have great regrets. We posted it on Craigslist about 4 months after we bought the unit and NO ONE would buy it for $300.00 even though we paid close to $600, and only 4 months old? What does that tell you? I have had to add 5 gallons (bucket) with each wash to make sure all the soap washes out. Very loud, takes a long time to wash and just worthless. This last weekend, we tried to trade it for a used $150 agitator washer with a used appliance store and they said theyd never be able to sell it and refused the trade. What does that tell you about the washer?

What happened to the days of buying a washer/dryer and having them for years! To spend a thousand on each and have holes in the bellow causing dirty water to Empty on your floor. Not once replaced, not twice, 5 times!!! Now Im looking to buy another. Old school for me...

I purchased a Maytag refrigerator from Home Depot on 5/17/11. It would run, then not run. It spoiled all the food not in the freezer and most of the food in the freezer. This happened early November, being less than six months old. My wife called on 11/8/11, they repaired it on 11/18/11. Ten days of no refrigerator and a lost of about $200 in spoiled food. The company would not pay for any of the money I lost for the spoiled food!

We bought our front load washer and dryer about 5 years ago and have had no problems with either. We also purchased a Maytag French door refrigerator 2 months ago to replace our Sears Elite brand when its compressor went out after 27 months (Ill never buy another Sears appliance).

This will be the third repair of this refrigerator in one year, the same issue of the refrigerator warming up. Water all over the floor due to ice thaw. Also food spoilage. I want another refrigerator at this point. The Maytag repairman is definitely not lonely. He has more business than he can handle with this defective refrigerator. Terrible. Do Not Buy!!

I purchased this machine 6 months ago - have called 2 repair people. Thank God I purchased at Sears with extended warranty, was just replaced. I would tell you if you are looking for a machine run away from this one. It tears clothes, have to wash everything on bulk wash or I would not get enough water to say how bad this washer is. If someone called me and said I won this washer, I would say no thank you. And if I had to say Maytag repair called them, said she not getting enough water. Now this is what they told him: thats how we designed it. Forget about big drum, you cant put blankets or any larger items, goes off balance. And I have to say, if I had the money, I would put to the road and go back to wringer type. So again, do not make my mistake. Do not buy this washer and let me say the second day I made a complaint, was told it take time to get adjusted...NOT. I give this washer a 0.

I have a Bravos washer model # mvwb45owqo and matching dryer. The price for the pair was $1347.00 plus tax. The washer and dryer were bought Jan 14 2010. 10-10-13 the pump went bad and was replaced. I paid $ 221.00 to have it replaced. 10-31-2013 I was washing a load of cloths and it was very noisy. I call the local dealer and they come out and said that it needs a drive shaft tub part #w10193886. I would be about $300.00 to replace the part. Also they charge $75.00 for a service call. I called Maytag and talked to Ashley (**) from customer service and she said they could not give me any help that the washer was too old. I might also add that my last washer was 3 years old and the motor needed to be replaced. It was also a Maytag. I always thought if you paid more money for quality it was worth it. I am sorry I did not buy a cheap machine from Sears or somewhere else. It would of been 1/2 of the cost and I could of replaced it after 3 years or so if necessary and still been money ahead. We also have 4 rental homes that have all Maytag in it. I will be holding my breath that they are not junk also. I will tell everyone I know not to buy Maytag and I will never own anything that has the Maytag name on it again.

It is not worth the money. I paid $2500.00 for a Maytag refrigerator that I had for two months. Two service calls were made to Maytag as of 07/07/2014, the problem no ice and the refrigerator stays warm. The problem has not been resolve and Maytag refuses to replace the item.

I purchased a Maytag Dishwasher April 6th, 2011. Its only 3 years old and now the control panel isnt working properly. Specifically, the start button. Contacted Maytag Customer Care service and they could not help me other than charging $80.00 for the Maytag Man.. which by the way, we arent suppose to see because of their superb quality in appliances. So I have a repairman scheduled for next week. I am an highly dissatisfied customer because the dishwasher is used once a week for the 3 years Ive owned it. Just a poor quality product which I will never purchase again. Model #MDB7609AWB3 Serial # F10202246.

I purchase a Maytag dishwasher from Home Depot on 12/31/11. Based on the their commercials, I thought they were dependable. I did purchase an extended warranty, as I always do with any new appliance. After 2 years, the dishwasher stop working. I contact Home Depot and the extended warranty and was told to contact the manufacturer. Maytag blamed the extended warranty for the problem. They told me they could not help me. And could not help me. I will never ever buy any appliances from Maytag again. This model is M936/110V cord.

I have owned my Bravos XL for over a year. Loads of wash have come out with rust marks. These marks do not show up on all items, only one article of clothing/sheet/towel seems to pick up the rust marks (usually a couple of dots near each other surrounded by a circle). They are always the same. They have shown up on sheets which were washed in a white cycle and on other clothes of various colors.I have ruined numerous new clothes and must accept the fact that these random but frequent rust-colored dots are part of my life. I expected more. Im getting ready to purchase a W/D for our home up North and believe its necessary to return to a basic model, probably a GE. Maytag seems to have jumped the gun on this one… putting new product out there, aware these unresolved issues remain.

The middle piece of glass on my four-year-old gas oven shattered. It was not being used, but when I called Maytag, they told me that that was not covered because I did not have an extended warranty, and that I can purchase a new oven door and would have to pay the service person. I hope they go out of business. Maytag stinks, and everyone should know this.

Im an 78 year old man, married in 1962. In all the years and two kids we have had just three Maytag washers. To me the gold standard of quality washers. When the motor went out in our 15 year old Washing machine I considered replacing the motor, which is well within my capability. I am a journeyman industrial machine repairman formerly with Ford Motor car company before retirement.Instead, my wife and I bought a Maytag top loader high efficiency washer from Best Buy. I was skeptical when I examined the new machine with paddles instead of the agitator. Trusting that Maytag had engineered a water saving washer using paddles, I made the very poor decision to buy it. I regret not replacing the motor in my old machine. Boy was I wrong. Given the chance I would trade my new machine for the old in a heartbeat...The old machine washed everything we could throw at it. The new machine wont wash anything to my satisfaction. The bedding deep fill cycle is the only one capable of a passable job. Even then I would like a soak cycle which, in my opinion, would vastly improve results. In all I would characterize this as a total engineering failure. Why Maytag would allow this POS to be sold, where the reputation of Maytag is totally destroyed, is beyond my comprehension.

Do not buy one. Maytag is unresponsive to repairs or parts that are needed. They are not even manufacturing the part that breaks. If you are lucky, you will find out there is someone who will fix the defective computer board... But Maytag will not tell you. We were without fridge for 4 months... They did not care.

I purchased a white Maytag gas stove over 12 years ago. It has been great and never caused any problems. I live alone and rarely use the oven. However, I use the stovetop daily for cooking. With continual use, it has a lot of nicks and scratches. It also has stains inside the glass oven panel that I cant clean. The glass would have to be removed in order to clean inside. This is why I give a rating of 4 stars. If I used the oven more frequently, I would notice if it had any problems with the temperature, proper cooking, etc. and could give a more accurate rating. I have small toaster oven and therefore, I cook practically all of my meals in the toaster oven.

Range is at least 20 years old and everything still works w/o issues. Our model has an upper level and a larger lower level that is a convection oven also. The top one heats up real fast which is great for quickly cooking and reheating. The lower one is large enough for everything else.

I bought a Maytag MDB7809AWW2 dishwasher two years ago. The control panel just started doing free-games. Lights would come on and off during the cleaning cycle. When selecting a cleaning cycle, some functions would be automatically selected without the capability to deselect them. It is our second and last Maytag dishwasher. Stay away from them!

We first purchased a Maytag Neptune washer and dryer set. We loved them. Had them for 15 years with no problems. When we decided to get a new washer and dryer, we were loyal to the Maytag brand. I was immediately drawn to the Maytag Bravos XL due to the extra large capacity. What a mistake! This washer and dryer pair take more than two hours to complete a single load of laundry. It often takes more than one wash to get clothes clean. If you wash an extra drum large load of laundry, often times there is not enough water and agitation to even get all of the clothes wet. I have a one-year-old boy and a six-year-old boy, their clothes get very dirty. This washer Does not get food off of my one-year-old’s bibs. And my six-year-old’s clothes come out looking as if they haven’t even been washed. What a disappointment! My husband and I are going out today to purchase a new washer and dryer set after having just purchased these Maytags in April last year. What a waste of money! Please include me if a class-action suit it’s taken.

Purchased a Maytag Bravo. One of the worse purchases weve ever made. First the much of the clothes does not get submerged. 2nd the clothes comes out extremely wrinkled. Called the Maytag people and they explained that Im putting too much clothing in the washer. I explained Im only filling the washer half way. They explained it should be filled only a quarter of the way. What??? Do not purchase this machine.

The Maytag Washer and Dryer we bought new and they have been great. The dryer was bought in 1972 and still works well. The washer was bought in 1997 and still does a good job. We are satisfied with the long time these 2 appliances have lasted. Do any appliances manufactured today last that long?

The control panel died on this dishwasher (MDB7749) after only 2.5 years of light use. I was quoted about $250.00 plus labor to have the panel replaced. I will not fork over several hundred dollars for a defective panel, especially since many others have complained about repeated failures and known issues with the control panel. No more Maytag products for me. I plan to purchase a Bosch to replace it.

We bought a Maytag French Door 21 cu. ft. refrigerator in 2008. 2010, 3 repairs later, the ice machine went out, we went back to ice trays. Now the compressor died. The old ad of bored Maytag repairmen cause they never need repairs is bogus.

This washer is garbage. Control panel went out twice in less than a year

Bought a new Maytag High Efficiency washer. I followed the directions closely, using the proper type and amount of soap, and the proper settings for the soil level. The clothes come out of the washer smelling almost the same way they went in. I contacted Maytag by email. Their response was to send me instructions on how to operate the washer. I responded again. Their response was basically Sucks to be you. This is the worst washer Ive ever owned, and the customer service is truly awful.

This is the WORSE POS I have ever owned/used/etc.... our clothes are dirty, w/ a scummy film, really bad in most cases. Some have weird stain appear that werent there. Electric & water bills up. Have to always use deep water wash, double rinse. My clothes are wet when I put them in due to sensor fill (extra weight), also a zillion mesh bags. Clothes are getting trashed, faded so bad & smell bad. Having to use a cleansing product monthly, in one aspect, should encourage the engineers that signed off on this POS to change careers. Maytag customer service says no complaints have been filed!!! Horse **!!! $ 800.00, trashed, unclean, wrinkled to the point of almost needing to iron all your clothes. I have been going to the laundromat. Engineers should have been FORCED to use this machine at least 2 months.... good reviews my **.

We bought our new Maytag top loading washer and matching dryer about 2 years ago. I am a busy woman so I havent had the time to write a review, but today being my day off, once again I find myself frustrated and disappointed with this set. The washing machine has a huge capacity, which was a huge selling point for me, however, if I put more than a small load in, the clothes come out still dirty, stinky and even have dry spots on them where they werent even in contact with the water. Even on deep fill it cleans the clothes inadequately, but at least they get wet. The dryer leaves the clothing rough and wrinkled unless I use the delicate setting, which I do for all cloths, and I use fabric softener liquid and a dryer sheet.I had a front load washer and dryer before, and my clothes came out clean and beautifully soft, but I replaced them because of the musty smell problem from the washer. I wish I would have kept them and figured it out. This set is the worst and I spent so much money on them. It takes so long to wash a load of laundry, and there is no way to interrupt a cycle without it draining and starting over completely. I have tons of laundry to do and I started 2 hours ago and the first load is still going. Geesh!!! Dont buy a Maytag. I paid for the extended warranty, but they are not broken. They have sucked from the very beginning.

Recently purchased Maytag Washer and Dryer from our local Home Depot June 2020. The appliances were finally delivered in August. When both appliances were installed, the installers made sure the washer was working properly and there were no leaks. They did the same for the dryer to make sure it was working properly. When the dryer was turned on however, the motor blew up and there was smoke coming from the dryer! I am now sorry I purchased Maytag. I had narrowed my choice between purchasing Samsung or Maytag. Im now thinking I should have gone with Samsung. Im supposed to receive another dryer today. The washer works, however its very, very loud. For the amount of money I paid, I hope these last for a while.

We purchased the Bravos X set (Model Number: MEDX700XW0 and Model Number: MVWX700XW2) form Lowes in October 2012. When the items arrived and we used the dryer for the first time in the delicate setting, the machine kept cutting off! So, Lowes brought us a new one. At first it worked but then the delicate cycle on that machine ended up not working as well a few months later. I ignored it and used the other settings. Yesterday, the washer broke. The entire basket detached! We were washing a small blanket and sheet set and kept hearing a loud banging sound. I went to check and the clothes were soaked and the entire drum was detached. I am so friggin angry! We spent over 1200 for this set and less than 3 years later, the set is ruined. I am on the phone with Maytag now b/c they need to replace this set or give us an upgraded set. They know that this set had issues yet they decided to still market and sell it. I want to sue!

I have the same problem noted by the other posts. Water leaking on hardwood floor from the bottom of the freezer. Refrig is out of warranty. Also, the deli drawer is also broken. This is a $2000 refrigerator and the quality is terrible. Please contact me for class action suit inclusion.

Our Maytag refrigerator was about a year old when we noticed rust on the edge of the stainless steel doors. I called Maytag and they were nice enough to replace the doors even though the warranty had expired by their standards. Keep in mind, the warranty starts when you purchase the product, not when you install it. We ordered our appliances from Lowes well in advance of our kitchen remodel so we would have them when we needed them. The time our appliances sat in Lowes warehouse used up two months of our warranty.Now, the new stainless steel doors are rusting and they are refusing to do any thing about it. Should stainless steel rust? Maytag doesnt seem to care whether their product performs the way they should. Its all about the warranty. Once the warranty lapses, they could care less whether their product blows up. Thats the customers problem. Whatever happened to building a quality product that lasted and customers bought for generations? Obviously, thats a thing of the past.My goal in writing this is to make consumers aware of appliance warranties. When I spoke to Lucas, a Maytag customer service supervisor, he informed me their products offered no warranty on the finish of the product. So, according to Lucas, the finish on your brand new Maytag appliance could flake off like dandruff and its your problem regardless whether its a manufacturing defect or not. Remember, buyer beware!

I am at my wits end, as I try to get some satisfaction for the fact that this stoves cleaning system does not work! We purchased this stove at Home Depot in Hadley Massachusetts on February 2, 2014, and it was installed in a seasonal cottage that we were having renovated. When we arrived at our cottage in May, I was delighted with the stove. The cook top performed well and the oven size was great. During the summer, we tend to grill outside so the oven didn’t get much use, but it perform perfectly every time I used it. I always remove any debris that may have spilled immediately, and didn’t see any need to user the AQUA Clean feature until we were getting ready to leave in October. When I ran the cleaning system as recommended in the manual, there was a stain on the bottom of the oven. I then ran it eight (8) more times with the same result.I called the service number and they scheduled a service technician to come for a visit. He said that the stove was working the way it was designed to and unfortunately since it really didn’t get hot enough to do the job, the stain (and with more use, more stains) would remain. He also noted that should I try oven cleaning products, my warranty would be voided. This was not the answer I was hoping for, but since his visit was on the day before we were heading South for the winter there was not much I could do.Have called the service number several time since then, asking what could be done to rectify this problem with no positive responses. One did say that they could send the service tech again and went so far as to schedule an appointment for January, which she suggested I postpone with the technician until we return in May. The reasoning being is that since the warranty is only for a year, and the cottage won’t be opened until May, the fact that the original appointment was within the warranty period would cover the cost of the visit. When the technician called a few days later, the scheduler said that it made no since to go again, unless Maytag came out with a fix for the cleaning system. Since it’s not broken, but just does not work. I again spoke with a service rep and asked if anything could be done or if I could speak to a supervisor, she said that one would call.. That was weeks ago and still no call.We purchased this stove with the hope that it would last for many years, especially since it is only used for five months of the year. Ease of cleaning the oven is important. Home Depot no longer sells this model, and after some searching the internet I have found that I am not alone with this issue. Apparently it is quite common. We will not be able to access the cabin until May 2015, but would appreciate anything you can do to expedite a replacement of this stove, with one that actually self-cleans or a refund.

My wife & I purchased our Maytag dishwasher model # MDBH979SAB1 on 3/8/13 from homedepot.com. Approximately 24.5 months later our dishwasher experienced control panel light button malfunctions similar in description to the many other consumer complaints on this & other forums. I would like to share some additional information based on my research about this issue and possible fix. The source of Whirlpools control panel issue is design related. The issue is caused from moisture which induces oxidation on the Flexible Printed Circuit (FPC) cable that is integrated with the control panel and connects via connector to the electronic control box. The issue usually manifests itself on the cable just where it bends coming out of the touch membrane panel.The oxidization of the FPC cable eventually creates electronic shorts or opens between the parallel traces thus causing the panel control lighted function problem which disables the dishwasher from being used. The cable, since integrated with the control panel, is not a separate replaceable part. In order to repair, the Whirlpool diagnostic action is to replace the entire control panel. I quickly learned after doing some online research about Whirlpools control panel issue that it extends back to at least 2011 with control panel part # W10475784 and corresponding or like PNs of this design. The number of control panels sold of this design by various online appliance part centers coincide with the high number of reported like control panel failures.In just 2015 alone so far, the sales for this control panel have been in the hundreds. This indicates that Whirlpool continues to replace defectively designed control panels upon failure with defectively designed control panels. There was also a class action lawsuit filed against Whirlpool in the state of California on May 6th, 2013 for the control panel issue. The filed lawsuit is public & the whole document is available online as a pdf file. Unfortunately, Judge **, granted Stipulation to Dismiss Case with prejudice 74 on 5/23/14. I was unable to find out any details as to why the case was dismissed. I did not call Whirlpool about my control panel issue, instead I handled all correspondence through Email to them at WHIRLPOOL_CUSTOMEREXPERIENCE@WHIRLPOOL. COM.My initial correspondence included all the facts about this issue & that I did not wish to have their warranty coverage/period explained to me for I understood them, the problem was a quality issue, and just basically wanted to know what they were going to do or have been doing about resolution. The email correspondence with them got me nowhere. They initially replied back with all the form niceties like We apologize, We understand your frustration, & We value you as a customer, but denied every knowing about such control panel issue, regurgitated their warranty policy & period and were unwilling to resolve anything. In their last reply they stated how unfortunate it was that customers only take the time to provide negative feedback!! This is just bad business, and though I would not like to think it, but the control panel issue may have been by marketing design.Please keep in mind that Whirlpool manufactures appliances under at least 15 different name brands including Maytag, Kenmore, Admiral Kirkland, KitchenAid, Roper, Speed Queen to name a few. All is not lost, being an electronics engineer I looked into the do it yourself fix. If you are not comfortable in doing this, you may be able to find someone to help. I was able to repair mine by carefully scraping off the oxidation from the FPC cable (will appear brown in color) & encapsulating it with high density 100% dampening silicon (non-caulk type) to protect it from moisture & withstand heat. There can be other ways of protecting it from moisture instead of silicon, just make sure it can withstand heat, wont become brittle, & that it may not cause potential damage to the cable itself.My repair has worked for about 4 weeks now, & shows no sign of oxidizing. The problem may be more severe if the oxidation has actually opened or broke one or more of the small cable traces. Do not attempt to solder this cable! Its way too thin & will only make matters worse. An open can be carefully bridged with a conductive glue or ink thats on the market. One source is a window defogger repair kit product thats sold at auto stores that has a conductive glue in it. Post open repairs will need to be checked with an ohm meter to make sure repair is good and that any adjacent trace lines have not been shorted by repair. Of those of you that have just bought or had installed Whirlpools defective control panel, please encapsulate the FPC cable as soon as possible to protect it from moisture. If you dont, it will surely oxidize again over time.

Fridge leaked all over our floor and ruined it! Very unhappy! When we open the freezer we find a sheet of ice on the bottom. We have to keep a towel on the floor so we dont slip and get hurt. I finally get a new kitchen and the fridge is ruining it! Yuck.

I had to replace a washer & dryer which was destroyed in a fire. We lost everything. I was hoping a new set would last me many years. Boy, I was wrong. Maytag Bravo washer is the worst by far. I havent even had it 4 years. I had a plumber in 4 times already. The pump keeps breaking; it doesnt drain properly. It appears that dirt is entering the clean laundry and the laundry has to be washed again. It looks like I have to research for a new washer. It wont be a Maytag. They are thieves!

Purchased Bravos 300 quiet series wash and dryer 3 1/2 yrs ago new. 18 months ago the washer gives me f51 and ul codes. To repair this USA made washer will cost over 250 dollars. I see why the Maytag repairman is not busy. Cause after 2 years you gotta buy a new one. All these digital controls are made in China - junk. Ill buy LG or Samsung next.

While washing clothes in my Maytag front load washer, I noticed that there was water leaking from the front left corner from the bottom. I have owned the washer for only 2 years, and Maytag manufacturer (Whirlpool) told me that it was going to initially cost $80.00 for a service call and then more money to fix the leak. WOW. Also the wood floors that are underneath the washer and dryer, is starting to warp from the leaking washer. I would recommend DO NOT BUY A MAYTAG APPLIANCE. The warranty is basically worthless along with the washer.

Disappointing that a Maytag would be a problem machine. Constantly out of balance when spinning and mediocre cleaning. Now it is spitting oil underneath. Am on my way to buy new machine with agitator.

Purchased Maytag Dishwasher MDB8959SFH4 as part of a kitchen renovation with hardwood floors. Realized that the dishwasher was leaking intermittently. Appeared that the door wouldnt latch properly. Called Whirlpool (parent company). Technician came out to assess the situation - couldnt recreate the problem so suggested replacing door seal. I try to explain to him that in my opinion it wasnt the door seal but a failure to latch because the top rack was not retracting completely on an intermittent basis. He also suggesting replacing the latch. Repair was carried out and same issue arose three days later. I systematically removed one dish at a time and then tried closing the door - after removing about the 6th item the door closed. Called the repair company today and they told me he had just received a recall from Whirlpool - apparently an issue with the tracks not allowing the rack to retract properly - what I have been saying all along. I called Whirlpool but they insisted the notice was sent out some time ago. I called Home Depot where I bought the appliance and they confirmed that they were not aware of this issue. I suggested they should not be selling this dishwasher until Whirlpool remedy the manufacturing defect. I will follow up with Whirlpool to let him know I have spoken with Home Depot and they were not aware of the issue.

I would highly recommend you do some research on the Maytag bravos XL machines and dryer.This thing is about as good as a piece of paperweight thrown in the fire for no good of nothing. Warranty ran out but it has a 10 year warranty so I don’t understand, bought one year ago been broke down three times in that time. Speed queen all the way.

We purchased a Maytag dishwasher at Home Depot in White Bear, MN in November of 2011. The dishwasher just quit running last week and the repair person told us the control board needs replacement. We will have the control panel replaced but have determined this machine is of very poor quality and will never buy a Maytag appliance again.

Dark clothes are left with residue on them, have to run another rinse cycle to get them clean. Been having this problem since we first got the machine. Anyone else having this problem or got a solution to fix it?

Purchased a Maytag MBF2256HEW bottom freezer in 2005. About fours ago, I had to replace the control board to the tune of $140.00. Today the fridge quit working and this time it appears to be the compressor, so tomorrow we will be shopping for a new unit. It will not be a Maytag.

The dishwasher (model number MDB7100AWW, serial number 158462977YH) that was replaced due to recall for fear of fire hazard has only lasted two years. Is there any recall on the recall? Our dishwasher was purchased in 2001. We live approximately 30 miles from the former location of Maytag manufacture, Newton, IA. In our 39 years of marriage, we have always had Maytag appliances: washer, dryer, fridge, and dishwasher with long lasting results. Our previous dishwasher lasted 23 years. It is very disappointing to feel the need to replace a Maytag appliance, which weve always felt was industry standard after such a relatively short life! It no longer fills correctly, and trouble has been diagnosed by service tech as bad control board. It seems theres a possibility of fire hazard once again. Can you offer any help short of replacing appliance as cost of repairs does not seem effective? Thank you in advance for your attention.

This top load machine replaced a top of the line Maytag Neptune. It has five water levels. It has three temperature settings and four wash selections. It also has a selection for an extra rinse that I use for white loads. The washer is very reliable. Clothes come out clean with an average amount of detergent. Although this washer is more than fourteen years old, it has never needed service or repairs. By running a cleaning cycle every six months, it drains like brand new. The stainless steel drum is still as polished as it was when it was new. Even the hoses have lasted with a need for replacement.

My Maytag top loading washer, 4 years old, stopped working in the middle of a wash cycle. Registered Maytag repairman did a diagnosis and finally identified the problem with the control board. The cost of the control board would have cost almost as much as the original wash machine especially since I had to pay for the current service call and labor (to diagnose the problem). After having read a number of other reviews from dissatisfied customers, I will not buy another Maytag product. I was under the impression that Maytag produced a superior appliance but was disappointed by this experience.

I bought a Maytag Bravos Quiet Series 300 washer just over two years ago from Home Depot. The control board and sensor went out last week. The service technician seemed rather surprised that a newer machine would have that kind of non-wear-and-tear problem and suggested that I contact Maytag/Whirlpool to see if they could help offset the parts costs, as the repair was going to cost over $600! The customer service agent I spoke with said that there was nothing they could do because the item did not have an extended warranty. I explained to her that we purchased this unit, even though it was out of our price range, because we were told that it would last a lifetime. I would have been happy if it would have just lasted 5 years! She was very detached and it was clear that Maytag/Whirlpool was not going to stand behind their product. I will now take the repair money and go buy a new washer. You can be sure that it absolutely will not have the Maytag/Whirlpool brand!

Neptune Washer: Tears clothes at random intervals and their help desk asks for money.

I will never buy another Maytag appliance. We built our home in 2005 and bought brand new Maytag kitchen appliances (refrigerator, gas oven/stovetop, dishwasher, and hood microwave). In seven years, we have had problem after problem with all four appliances. We had to replace the compressor in the refrigerator in the first 18 months and then the fan in the refrigerator about a year ago. We have had to replace the heating unit in the oven twice and the handle has broken off of the oven door twice. We have had to replace the handle latch on the dishwasher once and today, the microwave stopped working. We are not rough on our appliances (especially the microwave as we rarely use it), so I think the fact that every single Maytag appliance has broken down one to three times in different capacities in the last seven years says it all. We have had a very poor experience with this brand and will definitely never buy another Maytag appliance.

Maytag Model MDB7749SBW: Lights on control started flashing even when not it use, cycle lights varied, dishwasher would start on its own. Stopped at dealer and he said he never heard of problem. Checked online and found problem identified all over the internet. Called Maytag and they knew of problem and said they would send serviceman out to check. First trip free and parts would be free but I have to pay labor for second trip to repair. Dishwasher is just under 4 years old. Serial F31703877. Problem is corrosion on small flexible circuit at top of door. Same problem as others. Maytag states never been a recall!!! THIS CERTAINLY HAS THE POTENTIAL TO CAUSE A FIRE. Will never purchase another Maytag or Whirlpool appliance again. Poor quality and lies on the part of company and dealers as well.

I owned my double oven Maytag Gemini for 14 months and I was absolutely satisfied with it. I was running a cleaning mode on the bottom oven and the lock froze. I have tried everything with it to unfreeze it, including the suggestions offered on the internet. I havent been able to do it on my own and I cannot afford to hire a repairman. I called the help line offered by Maytag (after waiting for 32 minutes), the representative actually laughed at me when he found out it was past the 12-month warranty. Though this laugh may be unusual, I feel it is very indicative of the way Maytag handles any problems; Maytag doesnt stand behind their items, they are now built shoddily and they could really care less about retaining their customer base.

I bought a dishwasher from Maytag model #MDB774SBW0, in 2013, last year prior to the year warranty it broke. The control panel had to be replaced. This year its broken again. Control panel not working properly and its starting to rust on the outside in the corner. Per the company unless the repairman damages it out theres nothing they can do. I cannot believe this piece of junk. First of all it costs so much and has broken twice for the same issue in 2 years. Will not buy another Maytag, very unacceptable.

Maytag Bravos Quiet Series 300 - Just DONT BUY this junk. We bought the washer and dryer set from Home Depot in 2011 and have had nothing but trouble with the washer. Three times small objects like dimes, pennies and nickels got past the agitator into the drain pump which has been replaced twice. Beneath the agitator we even found a few missing socks. Today after a visit to the Laundromat, we bought a Samsung with a 5 year extended warranty. If that doesnt work it will be an old fashioned Speed Queen next. We will never buy anything Maytag again and I hope to influence everyone we meet about them. I cant wait to throw it into the city landfill for recycle dog food cans.

Have read others reviews and experiences and wish I had visited here first. Our first Maytag washer and dryer set lasted over 25 years with only minor repairs until the transmission started to leak grease and was uneconomical to repair. Our second set only lasted nearly 10 years and were obviously lesser quality. The wife decided that she wanted the best and high tech version. She really liked the features of the Bravos 300. What a mistake! Not even three years old and she has been dealing with the noise and the problem with constant unbalanced loads, intermittent error codes, odors and the forever cleaning requirement. The whites were intermittently getting rust stains until I determined that the underneath side of the top cover around the bleach reservoir had rusted out big time. I replaced the top cover for over $125 plus an afternoon that I will never get back. (Out of warranty, of course). Today the wife called me to say that the washer would not complete the rinse cycle and she could not reset it. We had to pump out the water and pick the wet clothes out. A grinding sound is coming from near the bottom of the machine and sounds expensive. The service man is scheduled to be here day after tomorrow to give me the bad news. My next washer purchase will NOT be a Maytag or any other high tech piece of crap. Simple is better.......

I have a stainless steel dishwasher, model MDBH985AWS10. Its about 5 years old. The control panel works intermittently -- Ive replaced and ruled out the door latch -- now Ive got the problem narrowed down to either the control panel or the circuit board. Ive read about this diagnostic cycle I could run to try to help diagnose the problem. I emailed Maytag for the code and waited a week and didnt get a response.I called them today and they said they cant give me the code--they only give that to their technicians. My dishwasher is not brand new, but I paid good money for it, and Id prefer to not have to guess what to buy when Im trying to repair it. Each of these parts costs about $150. Im not sure what the policy is for other dishwasher manufacturers, but for the next washer I buy, Ill find a company that either 1) has more reliable products or 2) at least tries to help the customer repair his own equipment.

I purchased a Maytag Legacy Series Quiet Series 300 in early July 2010. It had a recall for a heater part that could potentially burn down my house, so we couldnt use it while we waited for that part to be replaced. They offered me a small sum of money towards the purchase of a much more expensive dishwasher which I declined since Id only had the dishwasher a few months at the most. It is now the end of August 2011, a month past their factory warranty. The dishwasher did not get my dishes clean, made awful grinding noises and three days ago, it refused to drain and then spewed 50 or more gallons of water all over my kitchen which then leaked into the basement. The repairman charged $85 to tell me that the computer in the control panel had burned out and was not fixable. I think I paid somewhere in the region of $500 for this machine. My last dishwasher lasted about ten years. This is completely unacceptable. In searching the internet, I found hundreds, if not thousands of identical complaints. Clearly, this machine is a lemon and Maytag should be forced to replace it or better yet, refund the money spent to purchase the machine. Plus, pay for my valuable time spent mopping up water, washing dishes by hand, searching the internet for probable cause and potential solutions, waiting for Maytag/Home Depot to respond to my inquiries and a large sum for general annoyance. Maytag had a reputation of reliability (emphasis on had). Theyve got some slick ads but they do not stand behind their products at all. I will never by another Maytag product and I urge you to do the same.

We received our new Maytag washer MHW8200FC on Saturday 11/18/17. We washed 2 loads on Saturday and on Sunday it didnt start. Not only did it not start but it was locked with clothes in it. We finally got it to open but it wouldnt start to wash. We had the distributor, Warners Stellian, schedule a service tech. He came out on 11/21/17 and determined the board was bad and that he would order one and be back on 11/29/17. A week without a washer doesnt work for a family of 5. This isnt like a lawn mower I use once a week, we use it daily. Whatever happened to quality control? A brand new expensive product breaks in 2 days? Maytag says its Made in the USA, which Im all for... Only if it works. USA or China, broken is broken so I dont care where its made. Whether its planned obsolescence or just a plain faulty product, Maytag is now another brand that I will avoid buying in the future.