Bought a Maytag HD top load washing 11/4/17. Within the first month the machine began to make a loud squealing noise during the wash cycle. A repairman came out 2 times before finally replacing the gearbox and tub. Within the last month or so the problem began again, another repairman came out twice, and once again, had to replace the gearbox and tub. When he left I ran a load and the machine sounded like a war was occurring inside of it. Very loud banging and grinding... heck I was wishing for just the squealing back! Maytag refuses to replace the machine and just keeps sending out repair people. The Maytag name once stood for quality but that was long ago.

Maytag stove MGR7662WW - I purchased this stove about 4 years ago. Now, the stove will not light. I called in to Maytag only to be told I must pay a service fee or purchase a repair manual. It’s very strange. My old Kenmore lasted 22 years and here I thought Maytag would at least last 10 years less than half the life of my old stove, realizing products today are not what they used to be. Maytag, the dependability people, I guess that old Maytag commercial where the Maytag repairman is so bored claiming no one needs service for a Maytag product is really false advertising. Buy American products; I’m not really sure who is the current country who is home to the great Maytag corporation. I guess me and my wife will spend another $700 on another brand stove and try this process all over again, hopefully not again in approx 4 years.

Wish I had reviewed Consumer Affairs reports. When our old Maytag stove required repairs we decided to upgrade old stove instead of putting money into old unit. Looks like a huge mistake. Not only was there a delay in receiving unit after placing order but oven will not preheat. Two weeks before Thanksgiving we were promised a working unit. Now we are only 2 days from Thanksgiving, 2 repair companies have been at home to repair. Requires new circuit board and a new regulator to repair and no promise we can obtain parts. Now I have to figure out how to feed my family for holiday. I am pretty well done and after reading other reports that they are better in junkyard I think I will try to make them take back this defective Model 8800 product. Sitting in our kitchen unusable for the holidays. Dont buy Maytag as customer service does not exist.

I think so much about Maytag dishwasher with electronic controls that I decided to fix up my Maytag mdb3700awx by replacing the motor. It has an old fashion timer. It was trouble free for 10 years until the water supply line fail and sprayed water on the motor and shorted it out. I got a use motor and pump from eBay for 40 dollars. The dishwasher should last 20 more years. Too bad Maytag dont make them like they use to.

I paid $958 + tax for a Maytag Bravos washing machine in August 2008. I live by myself, so the machine is not overused. Nevertheless, it began to sound like a jet airplane during the spin cycle. And then in May of 2012, it failed with error code F51, catastrophic failure. The machine was not even four years old. I called a certified Maytag repairman. In less than 5 minutes, he told me the cost to repair would be about $900, and then he charged $115 for the service call! A call to Maytag resulted in Im sorry, there is nothing we can do.

We purchased a $945 Maytag 6.4 Cu. ft. self-cleaning freestanding electric convection range which was part of the stainless-steel package for $3600 + a $600-dollar 5 warranty. I did the research and found a solid 4.0 rating, so I went for it. Now I wish I never wasted my money and time. My 5-year warranty for all 4 appliances expired on 8/17 and now everything starts failing, how convenient. The oven will not heat past 340-350 degrees which won’t work with 90% of the stuff I bake. I called Maytag to see if it can be fixed and was quoted $400 for the issue but nothing else. I can pick up a new stainless-steel oven with the save features on a holiday sale for $500. Don’t waste your money on warranties!

I have had two Maytag washing machines in the past. Both lasted 20 years. Three years ago I purchased my first Maytag front loader washer and dryer. The washer is terrible. Although I clean it regularly plus spend money buying Affresh tablets and leave both the door and the soap dispenser open, the washer smells and builds up tons of mold. Cleaning out the heavy mold in the soap dispenser area is almost impossible. I spray bleach in there and then try to stick my arm into the back where most of the mold accumulates. Cant really get it all. Also, there is a problem with the softener dispenser. It gunks up and gets clogged. Had to keep pouring hot water and vinegar into it. Contacted customer service who was no help - they simply wrote to clean the machine. Huh? The dryer turns sheets into a tight roll with the inside not drying.

I have had my stove since 2004. A problem I have had was when I asked it to clean the ovens, it quit working all together. A service person was called. Also sometimes when I turn on one burner, another one will turn on instead. Yesterday I turned on a burner to low, and it did not turn on at all.

Maytag washer MHW5500FW had service just a month after purchase and still a year later the washer has problems spinning using direct drive. Even a few towels are soaked when cycle is done or errors out and must be restarted. Most of the time the washer has to be cycled on spin to remove water from soaked items, not just a simple bath rug, towels, bed sheets. Almost anything has a problem spinning. Had to purchase another year of service coverage as I dont trust the washer will last. Soap dispenser needs to be diluted despite using correct soap, per service tech advice which triggers sensors to shut down. Machine looks good but not ergonomically designed without the stand as you can easily lean over the washer and turn on and off accidentally. Same goes for the matching dryer, also can easily set off the on pause and on/off button. Dryer works great other than that.

I purchased my machine on June 2, 2021 and it was delivered and installed on June 4. I have successfully done two loads of laundry. On June 9, I attempted washing two small bath mats and 2 dish towels. When I returned to the laundry room to place the load in my dryer, I found the the items in soapy water. I tried many times to reset the load with no success. On June 10th I called Maytag’s customer service and spoke with an associate who walked me through a couple of common quick fixes. These also were unsuccessful. She referred me to warranty service. I will not be able to have my machine repaired until June 23rd! Obviously, if their repair department is so overwhelmed, the products they sell are a piece of junk. I am furious with both the product and the service I have received.

I have always thought of Maytag being the quality manufacturer of appliance products. We purchased a Maytag microwave (MMV4205DH-1) and after just two years it has begun to give us grief (we are in our early 70s, no family at home, so appliance receives medium usage). We constantly get the open/door message when we are trying to set the timer for operation. We open and close, open and close, etc. Just yesterday my wife noticed a slight crack on the door just below the handle, most likely due to frequent open and closing. Went online and read a number of reviews and found many others have had same or similar issues. Done with Maytag.

Oven door glass shatters after 6 years of having this oven and the company refuses to cover it. According to them it is not a safety concern. It is actually designed to shatter this way. Wow, thats comforting. Should be 0 stars not 1 star.

Maytag washer. The worst I have ever had... Never again. The tub does not wash, swish nor spin after 2.5 years. Absolutely a waste of our hard earned money... Never ever buy another maytag again. Had a tech come out and wanted to charge almost $500 to repair it. We told him to get out and never come back.

Its just me and my wife. We bought a brand new, top of the line Maytag top loader washing machine 7 1/2 years ago. It quit working last week. We called a reputable appliance repair company in Toledo. It cost $88 for the technician to tell us the Maytag computer system is not worth repairing. It looks great. According to the technician Maytsg is known for selling junk. My wife and I felt we were buying a top of the line washing machine. We were duped. We had a top of the line LG top load washer delivered today. Never will we ever, under any circumstances, buy anything from Maytag.

Purchased a Maytag dishwasher 1 1/2 years ago and the panel went out. I paid $550.00 for this item, wanted to get a nicer one hoping it would last. Of course they only have a year guarantee for parts and Labor. Will not buy another Maytag appliance again!!!

I purchased a Maytag model 4000 Front Loading washer in April 2010 and in May 2011, the tub bearings went out which is a $600 repair. Now in January of 2012, the tub bearings are going out again. Neither Lowes nor Maytag are willing to do anything to remedy the situation. Do not buy Maytag and do not buy from Lowes. Their major appliance buyer has to know about this and continues to retail a product not fit for its intended purpose.

Called to schedule service for letters on door to be replaced ice and water completely rubbed off until you didnt know which one you were getting. Refrigerator is less than 10 months old. Also freezer door was hung lower than refrigerator door. Was told nothing could be done. It was a cosmetic issue. Very rude customer service dept and I talked to two separate people and they were both rude and unwilling to help. I can promise you I will never buy any of their appliances again.

We moved into our first house just over two years ago and decided we needed to get a new refrigerator. We did a ton of research online, reading reviews, etc. We found a few not so great complaints regarding Maytag; however, we took our chances. (Note that we live in a house built in the 40s, so the fridge space is small and we needed a fridge size that is smaller than normal. We didnt have many options.) Well, a little less than 12 months later (yes, luckily right before the warranty expired) our ice dispenser stopped working properly. The mini-ice door would not close properly, resulting in a lot of frost in where the ice door was located. (There was so much we couldnt open the freezer door. It would get stuck.) So, we called out the repair guy and he said he had never seen this issue before and basically had to replace the whole flap and parts. Sweet. It was fixed and cost was covered! Well, about 5 months later, it happened again! Ah, they got it fixed yet again. Well, another six months later and after the warranty expired (lucky us), the fridge completely stopped cooling. (And it just happened to be Halloween, not a great day for a house issue.) So, we had to remove all our perishable food and place it in a cooler (which works hundred times better than Maytag products), and move all frozen food to a family members house 15 minutes away (luckily!). We were also super lucky we found a repair company that could come out at 5pm the next day, which happened to be a Friday! Awesome company (Conners Repair in Metro-Detroit). He concluded the defrost board was broken, meaning it was freezing and creating frost and then not defrosting, clogs the vents and not allowing circulation to occur. He was shocked when he found out we only had this fridge for 2 years and said this is something that normally happens in 20-year old fridges. I then decided to call Maytag and nicely requested a refund for the issue. I was told no due to the warranty expiring and also because we didnt use a Maytag repair company. I didnt want to wait a week as I thought this was something that needed immediate attention. I also am not sure why it matters who you get to fix your fridge. I have an invoice for proof of the issue and the repairman even said hed call to verify the issue. I don’t understand why I have to pay for something that was not properly produced, and not to mention the time out of my schedule to deal with Maytags issues. I now know not to buy any Maytag products due to the lack quality. I guess I learned the hard way.

We have had Maytag washers in the past, and they always worked well and were reliable. Not so with the Bravos washing machine. It is by far the worst excuse for a washing machine weve ever used. It does NOT clean clothes. It merely ingrains the dirt more into fabric. In four years, we have complained repeatedly to Maytag to try and get some kind of remedy to no avail. Maytag is simply not interested in standing behind their product. So now, after two generations, they have lost us as customers forever and we are telling anyone who will listen; DO NOT BUY A MAYTAG WASHER. They are terrible and not what they once were.

Because the design is bad, the refrigerator has to be defrosted once a month. A home filled with Maytag appliances, these are all 4 years old and ready for the trash. Dont buy Maytag, it is crap. They sell for money, not workability. The name has been trashed by Whirlpool. I am a builder and they will not ever see me recommend them, not even to a neighbor I dont like.

We had this washer 16 months. We bought it new from Home Depot. The clothes came out with spots on them, white residue and grease spots. This was ongoing for awhile. The bearings went out after 6 months. It was so loud now the water pump went out. I was told by Whirlpool (they bought out Maytag) that water pump is on back order and could take a couple of months!! To fix the bearings and the water pump was almost 700.00. A new washer is 1000.00. We junked it and had to buy a new washer GE. We are sick about this waste of money!!! What a piece of JUNK this Maytag Bravos XL is!! We need to have a class action suit and try to get something back. This is ridiculous and they arent taking responsibility. Whirlpool/Maytag are rip offs!!!!

I have only had this Maytag dishwasher for 2 years. My control panel has gone crazy! The child lock is blinking and I never touched it. I have tried to clear it by touching the heated dry button for 3 seconds, every once in a while it will clear. It eventually will start blinking again on child lock. I did research and have found out that Im not the only one that is having this problem. I now have to get it fixed.

We purchased a Maytag MVWB765FW top load washer with agitator to replace a Whirlpool with premature gear case problems (less than 3 years old). Was partially sold by the attractive metal label that says 10 YEAR limited warranty. It is now less than 2 years old and the Maytag selected repairman just diagnosed a failing transmission and of course advised us this is not covered by the warranty. Cost to repair—$ 600. About as close to false advertising as I have seen.I can’t believe that this company would sell such crap and not stand behind their products! But after seeing all these other complaints I believe it now. I bought both washers from Nebraska Furniture Mart and I realize they only sell the appliances but I plan to inform them that if they continue to handle Whirlpool and Maytag products they will never sell another appliance to me or to anyone else I can influence to not buy from them. We as consumers are almost powerless against these manufacturers but if we can influence the stores we buy from, just maybe we will see some improvement.

I purchased high end Maytag washer, dryer, dishwasher and microwave in May 2010. On Saturday 4/25/14, the Maytag Microwave stopped heating. The fan runs, the panel, display, lights, clock, and tray all work. It just doesnt cook. The Microwave was installed in June of 2010. Not even 4 years old. I have tried to troubleshoot via the instructions that came with the microwave, i.e. Check the demo mode is not on. Dont know why after 3 yrs it would be, but checked it. No help. Pulled the plug out and replaced; turned breaker on and off; checked to see if its was locked. Nothing. I then checked the door and I found that the plastic inside panel on the latching side of the door is pulling away from the door itself, which is part of the locking system. The magnetron shouldnt work if the door system isnt closing properly. The latch system is what is causing the door to pull apart. I am wondering now how much microwave exposure my family has been getting from a malfunctioning door? I have had a Microwave, dishwasher and refrigerator made by Maytag in the past. The refrigerator is 14 yrs old and still works fine. The microwave and dishwasher were at least 10 yrs old when I replaced them with the new Maytags I have now. Here is the problem. Maytag is not Maytag Corp. anymore. Whirlpool Corp now owns the Maytag brand. Prior to the old Maytags I had, I had GE fridge which was junk, and Whirlpool, dishwasher, stove and microwave. They were also junk. I swore I would never buy Whirlpool products again. Surprise.

Bought a refrigerator from Home Depot in November 2012 for a cost of $1,647.48. In August 2013 it stops making ice day 1, stops cooling & it is running nonstop, all lights on display go out day 2. Called Home Depot & was given another number to call, called that number was told someone would be out next day to look at it. Also told my warranty would expire in November & I needed to buy another warranty. Maytag customer service was very rude. If their product was any good why do I have to pay extra for another warranty. A $1,647.48 refrigerator that only lasts 9 months, REALLY!!! Do not purchase Maytag appliances if you dont want to lose your money. Shame on Home Depot for not standing behind their merchandise. If you have a problem while warranty is in effect, Home Depot should replace product.

Purchased this dishwasher 3 1/2 yrs. ago. Control panel went out. We would have had to pay almost the cost of new one to replace the part! Maytag used to be reliable. The dishwasher we owned previously (not Maytag) was still working after 12 years!

Weve had our Maytag dishwasher for less than 4 years when the control panel quit. The repairman came today. He was here 10 minutes and it cost us half as much as a new dishwasher. Its just the two of us and we use the dishwasher once every 4-5 days. Almost laughed when the repairman said the part and labor was under warranty for 90 days! There is no quality control anymore. Just greed.

Updated on 02/13/2021: Maytag stove purchased 15 years ago for about $500. Replaced mother board about 5 years ago which wasnt cheap, but otherwise, stove has performed with no problems and still looks and behaves like a new stove.Original review: Our 6-7 year old well cared for Maytag range oven recently stopped working. After a service call for diagnostics, it was determined the electronic module controlling the clock and all oven functions was dead. We were told by the Maytag service tech the module cost was 300$. That cost plus labor for less than an hour, plus the 60$ diagnostic visit came to almost 500$ which is close to cost of a new stove. The technician answered yes to my question, Do you replace a lot of these? He also said the cause may be power fluctuations making me think that surely there is a way to prevent this kind of failure. So, since the price seemed exorbitant, I wrote Maytag to inquire about causation/prevention, etc. I received a fairly prompt and polite reply with totally no explanation. I wrote another email with relatively the same results. I dont recommend buying an electronically controlled Maytag stove.

I purchased an expensive Maytag washer & dryer, top loading, energy efficient, only to find it now shreds all of my towels, robes, dress, undies etc. Maytag reply was to put things like undies, t-shirts, & dresses in bags to wash... What about towels? I had an expensive white Terry cloth robe from Neiman Marcus which is now shredded, Im showing it to everyone. Plus the dryer has an area above the front door that snags everything. I open the door & clothing is hanging there, caught on this area. Tell everyone not to buy Maytag, theyre rip-off. Ive lost more money on ruined clothes & linens than the trash washer & dryer are worth, but Im disabled, handicapped, 61 yr old who cant afford to buy another new washer!

We bought a Maytag Neptune front loading washer from Bens Maytag in Surrey four years ago and it has been nothing but trouble. There is no screen in the machine to prevent small things (like coins, screws) from going behind the rubber seal and into the pump. As a result, coins frequently block off the outflow to the pump so the machine doesnt drain.We have had to pay for service calls more times than we can count, and have spent more than original price of the machine making repairs and replacing the pump. We now have learned to take off the hoses and open the pump to remove coins ourselves, which we have to do every few weeks! Bens Maytag tells us that its our fault for letting coins go in the wash. There is no accountability for the faulty design of the machine that allows this to happen. We should have cut out losses and thrown this piece of junk out three years ago. We want Maytag to take responsibility for the faulty design of this product and to credit at least our purchase price toward another machine that works properly!

I bought a brand-new dryer Maytag Bravos. It broke after 3 weeks. They came to fix. A few months later, same thing happened, but I have 6 people in my house. They told me someone would be here the next day, and then that person canceled. They called someone else. He came and said I have to wait 3 days for parts. I called at least 6x and waited 30 minutes each time. They kept telling me theyd call back, and theres absolutely no call back. Then I called corporate Yvette, who was totally cocky and rude (866 817 5404). She said she would try to get back to me another day because she had meetings! Then, I was irate. I mean how rude. So she called me back and said, I ordered you the parts. Now you call Dan Marc, the service company, and make the appointment. Is this woman kidding? Then she went on about how Maytag has a 13% rating (They are Maytag.) and how their product is so wonderful. Now this woman is competent cocky and rude, and shes the presidents secretary! So whatever I call Dan Marc, they have no appointments Tom and wont make me an appointment. This is how a new product should work? I asked her what I do when it breaks again and again and the warranty is up. She told me they dont work on what ifs and if that time comes, it will be her decision. I am disgusted and have a house full of kids with no dryer? And I have given them another chance after that Neptune disaster. Im appalled and dont even know what to do.

This Maytag dishwasher was purchased because Maytag has always been represented as a reliable brand. Wish I had done some research on this problem before repairing it! The control panel went bad after 18 months (and at least 6 months of this time it was not used at all!). The repair cost $300, the dishwasher only cost $429, and if I had realized how much this would cost I would have bought another dishwasher instead. Wonder how long this control panel will last? I called Maytag to complain and was told by Dana badge no. ** that there was nothing to be done as it was out of warranty. We have had dishwashers for 10+ years before that never gave us any trouble. I told her I wanted to speak to her supervisor and she told me she didnt have one! Really, how about if George Moore the CFO or Arthur Learmonth the President call me back on this one! We shall see what they say, but I can see by all the complaints about the same issue with Maytag dishwashers that we will probably be out of luck unless we start or join a class action lawsuit (looks like there is one in California already). I will amend this post if Maytag decides to stand by their product and at least pay for the cost of the control panel, but Im not holding my breath.

Purchased Maytag washer/dryer in November 2016. Have been dissatisfied ever since. Dryer doesnt dry clothes completely after 90 minutes on high setting. Washer leaves white residue on clothes. Noticeable on dark items. Hardly any water on deep water wash cycle. Bedding just makes a big rolled ball. White powdery residue doesnt come off easily. Rewash, dryer, brushing. Ruining my clothes. Service has been out and they dont appear to know how to correct problem. Maytag doesnt know what problem is and their engineering staff hasnt provided any information on how to fix. Maytag seems very disinterested in helping. They just thank you for being a loyal customer. Not anymore. The attached pictures were taken March 11, 2018.

I bought a Maytag dishwasher to match other appliances in kitchen. Work great, not loud and gets dishes clean. Have owned it for 10 years and have one problem with the door latch. But it was easy and inexpensive to replace.

MF12569YEM2 - Purchased refrigerator less than 2 1/2 years ago, also started having issues with ice forming in bottom freezer and leaking on to floor. I shut the water source off to the water/ice feature, but it didnt solve the problem. After getting on this site and seeing the issue is quite widespread it seems that it should be considered a manufacturing defect. This is the second (actually third) Maytag Refrigerator we have had, one had actually needed to be replaced about 13 years ago because of electrical problem which service man said could cause it to catch fire. The replacement (different model) worked fine for about 11 years... so we decided to try Maytag again... WHAT A MISTAKE! After reading about the multiple problems we can look forward to and endless service calls I too would never purchase any Maytag or Whirlpool appliances in the future...maybe the company should think about the impact on lost consumers!

Maytag Centennial washer - Bought this washer brand new and after the first 2 months started having issues. The washer took FOREVER to fill and to complete a basic load took literally an hour or more. Then within the next 7 months it stopped spinning out the final spin cycle. Spin light would flash as would lid lock but wouldn’t spin the water so I had to manually unplug the machine then plug in out cycle on drain and spin and that worked 50 percent of the time. Repairman came out and said could be a number of issues but he said honestly it would cost me a lot less to just go buy a new washer! This is INSANE! I grew up with the Maytag repairman commercials and thought Maytag was still top of the line but LEMME TELL YA, IT AINT! The Centennial is a total piece of crap so PLEASE don’t purchase this machine as I can promise you will NOT be satisfied! MAYTAG, STEP UP YOUR GAME BECAUSE YOU SUCK.

This dishwasher is extremely quiet and very attractive in the kitchen. Easy to use and does a great cleaning job. The price was also right. Would definitely buy again.

I inherited this Maytag washer, so it has been around a very long time (I have had it for 18 years). It still runs quite well, has 3 levels of wash/rinse, 3 cycles to wash in. Both of us...me and the washer are still kickin together. Highly recommend Maytag.

This microwave doesnt rotate in use, it only goes back and forth...not as good! I believe the rotating type of microwaves heat your food more evenly, but it might just be a personal preference. I would NOT recommend this type of microwave.

I bought this wash (XL HD) 1 1/2 years ago. From the time the people installed it it never worked correctly. I have never wanted to beat up an appliance before, but this washer makes me so mad that I am ready to just throw it out and buy a new one even though I paid 600.00 for it and it was more than I would ever pay for a washer. I bought this so I could wash my comforters mainly. Well I cannot wash comforters unless I wash them 5 times or at least try to wash them 5 times or more. They get unbalanced and then the machine shuts off. After doing everything from changing the hoses like somebody else suggested, it still didnt work. Along my troubles with trying to rinse and drain I did find something new that I didnt know I could do for all these months is when you put your machine on rinse, spin, dry and the extra rinse light pops on, click it and turn it off, then it reduces the spin time to 15 minutes instead of 26. Also now I have to just let my hose drain on the floor of my outside wash room because if I hook it up through the wall to drain outside it just stops with the LF code. So I have 2 inches of water on my washroom floor and it really sucks. This is the only way I can get the machine to work without turning itself off. Very disappointed with this machine that appears to be so large (looks can be deceiving). It cannot wash hardly anything and this machine should be taken off the market. It is garbage. I really wish this did work because I have spent too much time trying to rewash, respin, get all the water out of the clothes so I could dry them. This should be banned and not sold by any store.

I have a 2 year old Maytag Dishwasher (barely used - it is a weekend house) MDB7749sbm1 and the control panel went out about 2 months ago – I followed another person’s advise of hitting normal and heated dry buttons 3x quickly and that seems to wash the dishes – not sure what cycle it is on because all the lights go on including 2 hr delay. I called Maytag and they kept me on the phone and hold with multiple agents for 34 mins and finally agreed to send someone at no cost to see if the problem can be fixed with no cost to me. I will keep you updated.

wW have had this Maytag gas range for twenty years. It has performed well for that length of time (maybe longer). During that period I replaced one burner. Only complaint is that the oven does not heat as quickly as I believe it should.

I purchased my dishwasher exactly two years ago. We are empty nesters so it has had light use. Today, when I tried to start it, the control panel would not work. Thanks to what I found in your site. I will not take a day off of work to wait for a repairman only to have it fail a second time. It is hard for me to believe a company that builds its reputation on a bored repairman would produce a product with a faulty control panel and not do something about it. Like your other folks, I will never buy another Maytag product and will not the waste the money to repair it. I am going out tomorrow to buy another dishwasher and throw this one away.

Bought a Maytag Washer & Dryer and after only 4 years the front panel went...cost to replace part only $653.55. After expressing concern about the price Maytag cut the cost of the part in half - now installed $475.00. Disposable dryer. Choked on it and decided to go ahead with the repair. Part was to be in in a week and it is now been a month. Maytag/Parts supplier no idea where the part is and doesnt return phone calls. Have to use the laundromat (family of 5). More money out of pocket. Not to mention time. Called Maytag again to complain about the service and having to pay more money out of pocket to use the laundromat. They basically told me, Too bad. Have used Maytag appliances over the years and always been satisfied but the company is clearly going downhill.

The efficiency of cleaning even dried on foods and getting them perfectly clean and dried is unsurpassed. And the need for dishwashing soap is always at a minimal using this Maytag Dishwasher.

Maytag dishwasher MDB7749SBM2 - I purchased this unit from Home Depot. It worked fine when working. In less than two years the control panel had issues. Would not let you start cycle, would randomly start on its own, would light up randomly, would only let one cycle work, would not work at all, etc. I received no help from Maytag. After open up the door panel the problem is obvious. The ribbon cable from touch (control) panel to control board had black spots from corrosion. Poorly insulated or poor design. $150 for part and another $100+ for repairman. As Ive seen from several of these posts it appears to be a common problem now to Maytag, which they choose to ignore in spite of class action lawsuits. Obviously last Maytag product Ill ever buy.

Add me to the long list of disgruntled buyers of a Maytag Dishwasher. Just like the other 488 people that similarly filed an unsatisfactory rating on this site I too am now on that list. And no surprise - the control panel ceased to function 13 months after I purchased the unit and one month after the manufacturers warranty expired. After brief inspection the problem was obviously a design error leading to premature wear of the electric ribbon in the handle. Phoned Maytag and they advised me it was the first theyd heard of this problem with the model. Only subsequently did I search to discover that the problem was so common it might be characterised as routine. Replace part was 8 weeks and Cdn $153, about 2x the US price. However they wouldnt ship it to me from the US. The repair isnt too difficult: 11 screws and a little patience if youre so inclined. Before installing take a few minutes to trim the plastic where the electronic ribbon strip passes from through the handle without clearance. Save yourself the same repair in another 13 months. Lesson learned - no more Maytag/Whirlpool dishwashers for us.

Maytag Dishwasher model MDBH989AWB3. The dishwasher was purchased at Home Depot March 19, 2010 in Hollywood, FL; delivered to our new home April 16, 2010 in Brunswick, ME. My complaint is the exact same complaint as the previous 28 complaints! I think the reason our unit worked for 6 yrs is because it was in use only 6 months a year. My experience: you make your selection, two lights come on, you press start, but nothing happens. You think this is a simple repair. You read the manual and try their troubleshooting advice, but to no avail. When you contact the company, they tell you that this is going to be an expensive repair, probably over $500. You contact Home Depot who want nothing to do with you or your dead dishwasher. Their advice: contact the Maytag company. You contact local appliance repairmen and they will repair it at a cost of over $500. You offer the unit to the repairman for free; he declines. He suggests you check the online Consumer Affairs site. It is on that site that you realize the dead dishwasher belongs where one brings other dead things: the dump. I will NEVER buy another Maytag product. I would suggest no one else does either, unless you want to practice your skills in dealing with frustration or you want to throw $693.40 to the wind and watch it flit away helplessly. Thank you for reading this.

I bought the product thinking Maytag - should last a long time. Sadly I was wrong. Bought the microwave from Home Depot in May, 2016 and had it installed by them. The product worked fine for the first 14 months. In fact I thought it was great. It was quiet, heated things quickly - a great product. In July, 2017 I started having problems. The product would start. I was getting a message to Close the door to start the microwave, even though it was closed. When this would happen I noticed that when the door was open, the light wouldnt come on. It would require multiple open/close until finally the light would come on (when door was open). Only then, when I closed the door would the microwave operated as it should. I lived with this inconvenience until Dec, 2017. Of course - over the holidays is when it decided to quit working entirely.I did my digging and found problems with the switches. I replaced 1 switch - still didnt work. The cost to have a repairman come out is ridiculous (Sears wants $250). My frustration was growing and my confidence in the product was waning. So time to get another microwave. I was done. Frustration and anger doesnt begin to describe my feelings. I went with another brand. It isnt installed yet, it should happen this week. In the future I will tell friends to avoid Maytag microwaves. Apparently they just dont last. I realize this isnt a top of the line microwave, I only spent $299 (plus tax, installation...) but really - shouldnt it last more than 14 months before it starts giving me problems? Very disappointed!!!

I bought a new Maytag washer 1 year ago. It does not do a good job of washing the clothes. I have tried to contact customer service but what a waste of time that has been. I would never buy another MAYTAG washer again. This is after owning an older style Maytag for 25 years that I never had one problem with until it wore out. They are now junk. I bought at Leons. Would be very careful of buying there again as they were also no help with this washer not working properly.

Home Depot is selling defective appliances manufactured by Whirlpool and refuses to provide a full refund. I purchased a Maytag washer and dryer from Home Depot in August of 2010.Washer broke in February of 2011. No parts available for repair, Whirlpool replaced washer after 4 weeks. This washer broke in July 2011. No parts are available for repair until August 17th.

I bought a Maytag refrigerator, model MBF 2256 KEQ2, two and a half years ago. Now the cooling coils are freezing up. I checked heater and thermostat for continuity and they were okay so the only thing left was the timer control circuit. On the earlier models, the timer control circuit is controlled by a Timer Motor or an Adaptive Defrost Timer which is separate from the main Electronic Control Board and much less expensive. On later models (including mine), the timer control circuit is incorporated into the main Electronic Control Board so if your automatic defrost quits working, more than likely you will have to replace the main board. I did not purchase an extended warranty because I believe they are useless from past experience. I bought the part on Amazon.com, received it in four days and replaced it myself for a cost of $78. This part costs $110 to $118 at Sears or a Maytag dealer.

Maytag Bravos top load washing machine - This is the worst washing machine I have ever used. Like some of the other complaints it leaves lint on your clothing. It does not put enough water in the machine. The so called smart technology that senses your load does a terrible job. Your clothing is halfway out of the water, with dry spots, even after 10 minutes of agitation. I am constantly adding 3 to 5 gallons of water to my loads to get things in the water. And if I want to let thing soak for a while you have to unplug the machine, because after 10 minutes it will automatically drain the water out. 2 years of dissatisfaction. I cant wait for it to die. I should have come to this site first. Never buy a machine without an agitator!

Purchased a Maytag Atlantis washer at Lowes in 2004. Until recently it worked without any problems; however, the agitator never seemed to work quite right. Normally, an agitator rotates in such a way that the auger action of the vanes pulls the clothes in toward the middle and then down into the water such that you have a continuous cycle of clothing being pulled down the middle, agitated at the bottom, then pushed up the outside. This one agitated but the clothing would just go round and round in the tub. Everything managed to get clean enough, but clearly something was amiss. Recently, the spin cycle became loud. A rumble became a loud roar over the course of a few cycles. Then I noticed water on the floor coming from under the washer. The short story is that the center shaft seals had just worn out. After almost 12 years of use, thats not surprising. Whats surprising is that it had worked so long without any issues other than the agitator.I took it apart and, to my dismay, the water had gotten into everything so that some of the metal parts were hard to remove. After having determined what replacement parts were necessary, I ordered them, but then placed additional orders for parts that probably would wear out eventually. So I ended up doing a near-complete rebuild. Other than the difficulty of taking some of the parts apart, and removing/installing the tub springs, it was actually pretty easy. I have reassembled, and now it seems to work flawlessly... so far. About the agitator: I found that shims are used on the transmission shaft to adjust tension. Too much tension and the clothes just ride around the tub; like mine did. Too little tension probably results in the thing not agitating at all (I dont really know). Once the washer is apart its easy to set the tension (insert the shim washers) correctly.There is a clip that holds the shim washers in place on the shaft. It was really tight; somewhat difficult to remove. One of the shims wouldnt fit when I tried to reassemble. As it turned out, that was a good thing. My research on this model revealed the way to get the proper tension. My assessment is that whoever assembled this washer at Maytag (or whoever builds these) assembled it incorrectly! Another thing I found out - after I ordered/received parts, unfortunately - is that there are two types of tub/shaft seal sets for this washer. I ended up replacing the newer type seals with the older type. Everything fits, but I may be losing out on a newer, better design. Well see. Overall, I am very pleased and impressed with the longevity and reliability of the MAV9501EWW washer. I have had Kenmore and Whirlpool; neither of which was nearly as durable and reliable. I hope this is helpful to someone.

We purchased the washer and dryer pair...beautiful looking, no agitator, water efficient. Load sensing feature. TERRIBLE, TERRIBLE, TERRIBLE. WORST APPLIANCE WE HAVE EVER PURCHASED. Used it 3 times. Clothes would not rinse, left white soap residue in the folds of the black clothes, even after a second wash. Home Depot was just the GREATEST, they replaced it for us. We went with a less expensive model GE. With the agitator and full water load...save yourself A LOT OF TROUBLE, stay away from Maytag Bravos XL.

I have a two year old version of this dishwasher (MDB894995BB3) and now the start and cancel light on the control panel stopped working. I now see that this is a common theme with this model and I feel it is their obligation to repair these units with permanent fix and not the same thing that will fail again. I have 3 different Maytag appliances all bought 2 years ago from Home Depot and they are all broken. I will never buy a Maytag product again. I might replace this dishwasher as I know it will fail again. 2 years on a dishwasher is a complete failure. Unreliable Junk. Do not buy Maytag.

Bravo Large Capacity Washer with Optimal Dispensers - 4.3 Cu. Ft. - The washers shortest cycles take at least an hour (not including having to do another spin/drain) and uses such little water that I have to use the extra rinse cycle on most loads. The washing machine is VERY hard on the clothes; towels (which I feel are pretty hardy) have been destroyed. Today the machine stopped draining/spinning completely and smelled like it was burning. I called the warranty number and was told it would be a week until someone could come out. When I tried to escalate a sooner repair date the manager Jessie refused to assist in any way insisting there was nothing he could do. I spent the morning calling my local repair shops and was able to find a Maytag warranty repair person to come out the same day, but had to call the warranty number again and have Maytag place the request. Sorry for the long post, but this washer is the WORST purchase I have made. The warranty experience was very unimpressive. I will not be purchasing anything from Maytag/Whirlpool/Jennair ever again.

The oven range (model number mgr8772wb) will not heat to proper temperature. It runs 35 degrees cold even after the built-in adjustment of 30 degrees. the repairman said it was just a cold-natured oven and we had to get used to it. So if a recipe calls for 400 degrees, you must preheat to 430 degrees. As much as this thing cost, it should cook properly. I must rethink Maytags reputation. I thought they were the best. Wrong.

We purchased this terrible machine 2 years ago. The clothes come out worse than when they went in! White powdery stuff all over darks! I always have to wipe all dark pants down with a wet cloth! Absolute junk! Really bad product! Never buying from this company again!

Bravos XL top loading washer looks nice and very large, but thats about how deep it goes. It leaves even a small load half-unwashed unless you select deep water wash and even then it FAILS TO USE ENOUGH WATER. I tried to go and fill it up once with tap water and it totally DRAINED THE WATER AND SOAP before it unlocked! It was on Deep water wash and the top of the load was totally dry as I dumped the hot water onto it.It is a bad design and it should have never been sold. I know it has special places designed only for HE detergents but when you try to use a Tide Pod the detergent NEVER FULLY WASHES OUT OF THE CLOTHES.... Too small a load, too big a load, exactly 5 pounds or exactly 10 pounds it really doesnt work very well - AT ALL! I was thinking that I might like to get some SHOS at the low price it is but now I can see why they are definitely not getting back into business.

I purchased my Maytag Centennial 1 and 6 mos ago and it is already broken. The washer wont wash the clothes, just sit in the water and wont spin. I called Maytag, they offered me a warranty for another year for $371. The washer was only $550.00. When I tried to get set up with a repair service, the only company they used which was going to charge $105 just to look at it, would only take cash. When I called back to discuss with Maytag, they were no help at all. I was told they wouldnt even do the warranty since I scheduled a service even though I canceled it. I will never buy Maytag again.

We have a Maytag dishwasher that came with the house we purchased in 2012. Im not sure of the exact age but the former owner said it was a relatively new installation. The appliance works very well; cleans well. Just a couple of things of concern. First, it is really noisy. The fact that we can very clearly hear it running in the adjacent room does not speak well for it in this regard. The other things that has occurred is that rusting is evident on the trays of the dishwasher. One of the upright pieces has already broken off due to rust and two others are close to coming apart very soon. Nothing sharp is placed in those areas that are coming apart so there would be nothing remarkable to disturb the plastic coating on the wire racks. I can only conclude that the plastic coating was defective at the start; hence the rusting at the base of the upright pointing racks. That said, it does clean well but I dont foresee this unit lasting much longer overall due to the rack damage that is continuing to occur. I would expect the racks to at least last as long as the dishwasher but this does not seem very likely at the rate the racks are deteriorating.

My washer is new, out of warranty, and about 2 and a half years old. All of a sudden, with no warning or previous issues, the computer board in the washing machine malfunctioned which caused a humming noise, it would not cycle into the next wash phase, the time would go up instead of down, I could not change cycles, and when I would push the power button there would be a delay of power coming on. I unplugged and called my local appliance repair and he said he sees problems with this model regularly, although not always the same issues.Before purchasing I scoured the internet for reviews on different units to make sure I didnt get a lemon. I think Maytag saw the error of their ways quickly and stopped making these before people caught on. This model is no longer being made. I like matching units, so it meant either shell out $500 for replacing the board, or replacing both the washer and the dryer that still works, which would be about $1200 or more for a new set. I chose the least expensive route for now. Not that it matters where I bought mine, but Home Depot and it was on clearance so it was a good price. I have now made up for that difference in repairs.

This has been the worst washer I ever bought. First the washer does not fill with water even on the deep fill function. It pours little water and washes the clothes with basically no water. The sensor for the lid broke less than six months of using it, soap residue is left on the clothes. I do not recommend this washer at all.

Bought a Maytag Front Load MHW6000AW washer and had a problem with amount of water in wash cycle. Dealer sent service men 3 times and changed several parts but washer still did not work and both repairmen said they did not know what was wrong. They called Maytag Tech Support but those people did not listen and said if no code shows up the machine is operating properly. Maytag then sent another company repairman. He worked 2 hours and said he could not find the trouble and Maytag support hung up on him. Maytag then sent another company repairman and he did one test and said the machine is fine and left in about 15 minutes total time. Now Maytag refuses to send another company for another opinion but I have a $1200 machine that still does not work properly. I am totally dissatisfied with Maytag and will stay away from their products totally. Companies wonder why people buy foreign equipment and this is the answer. I had a Samsung washer and never had one bit of trouble with it.

This is a review of a washer that is no longer sold. I bought a top of the line Maytag washer 45 years ago. After around 25 years the control (all mechanical) started sticking during the cycle. I opened it up, sprayed it with TV Tuner cleaner, worked it a few times, and it has worked perfectly ever since. That is the only problem or repair on that machine since it was purchased!

I bought the Maytag Bravos XL 5.3 washer because it was advertised to conserve water and it was a good brand, but it was a horrible mistake to buy this washer. The washer barely uses any water to clean properly and it hardly moves any of the clothing. The only thing that does move is the clothes at the bottom while the clothes on the top stays still. After using it for a day, I decided to return it back to Home Depot where I bought it, but they did not accept it and told me to call Maytag to return it. I called and the person who answered gave me different numbers to call. After going through ten different numbers, I finally received someone that could help me and they told me that I could not return the washer. They told me that the only way to return it was if there was a mechanical problem with the washer. It is extremely frustrating because I paid over $800 on this washer and now Im stuck with this garbage because I cant return it. I recommend everyone to not buy this washer otherwise youll get the same problems I am getting. I have to manually stop the washer and move the clothes by hand.

I unfortunately just had the same issue concerning my unit. The unit went berserk, stopped cooling and ruined all my food. I managed to get it outside after leaking spoiled food all over my floor. I washed it out and contacted Maytag after reading the hundreds of complaints. They sent someone out to fix the panel but he couldnt get it to cool. He said many times when a unit goes down that the acidity from produce along with moisture can eat through the aluminum components causing a freon leak. Obviously, this happened to me. I contacted Maytag and they said they would fix that too but once I called back, they said that it was a separate issue. Then I spoke with another person who said they would send a tech to inspect. I took off work and finally got a courtesy call from tech saying he was told not to come. I was amazed I missed work waiting and got no call from Maytag saying they changed their mind. I called back in and was told flat out I would not be covered, even though the fridge was fine before this happened. I suggest everyone read over the Consumer Protection Act which covers defective equipment causing issues by both injury and property damage. A class action lawsuit needs to be organized concerning this also. In the meantime, I implore each of you to file a complaint with the Better Business Bureau in your state along with Michigan where Maytag is headquartered. This will guarantee a response from corporate. Also, make copies of this forum and send it to your State Attorney General explaining how you have been sold a defective item. They say ABC news once did a segment on this fridge issue also, so I suggest contacting them asking for a follow-up story. For those that use social media, go onto their Facebook and Twitter page to post a link to this site and the way you have been treated after spending over $2,000 and a fridge that has lasted 7 years or less. Its time for small voices to unite to form one that is much larger.

Purchased our side-by-side stainless steel refrigerator. After about three months, we too have a constant puddle of water outside the bottom freezer door. Maytag came out for the first year it was under warranty, each time saying it was fixed. Its still not fixed and its been three years. We have to keep a towel next to the fridge constantly and have experienced floor damage. Class action suit? Sign me up!! My Maytag double oven has stopped working, and my Maytag dishwasher does not clean my dishes at all. I will NEVER buy Maytag again.

The ranges are getting great but are more so with digital than buttons and knobs which they should still have, especially for the handicapped and some elderly who prefer them. It would help prevent injuries. It was hard for me to find the knobs.

I have always loved Maytag but this top load washer is a bust. I purchased this higher dollar energy efficient washing machine to hopefully get the value out of it for years to come. Model MVWC565F. 4.2 Cu Ft. I use good quality liquid laundry detergent. I launder adult clothing (including business casual wear), sheets, towels and pet blankets. Occasionally the 20+ something children do their laundry while home. I often have dry spots on my clothes where they never got actually wet. I switched to only using the deep water cycle; however, this does not immerse the load in water. The smaller my load the less likely to get clean. Ive adapted to only have large loads but I still do not feel my clothes are getting clean. I often have to run the load a second time to not only remove ordinary day-of-wearing smells (very noticeable in socks for example) but to get them all wet and free of soapy/linty-like spots left on the clothes from the washer (most notable on black leggings, dress pants, etc). I always do my towels and bedding separate from daily clothing, so this is not coming from having a mixed load. I have also noticed that the load takes much longer (up to 2 hours) for my washing cycle. How is this energy efficient? It uses less water but more electricity? I miss my old fully-immerse-in-water washing machine that washed in under an hour! Love the dry that I bought with this but not the washing machine!! I do not recommend this washing machine!!

We have had the oven, a Maytag Gemini Double Oven model mgt8775xs02, for 3 weeks now and I am so upset. First off, I became violently sick from the oven when we first used it. I had a horrible headache and then nauseousness and then the worst stomach problems I have ever had. The toxic smells coming from the oven were too much for me. We had every window open. I looked online and found other people who reacted the same way to their new oven smell. But now we are on the 4th time using the oven. We did a self-clean and I thought that would help but no, it smells like someone is pouring gasoline into my home. I smelled it in pockets throughout my house. I have had the gas company out twice and a repairman. They all cannot figure out the problem. I looked online to see if other people were having a gas problem from this model and I am not finding it. It is horrible. I feel like I am being poisoned. I have not had a working oven in 2 and half years and I was so excited to get this oven and now my new oven is making me so sick. I am not sure what to do from here.

I purchased a Maytag French Door Refrigerator in July 2011 from Lowes online and had it delivered on August 16, 2011. In September 2011, I could not get the ice maker to work. So I called Lowes and they called in a repairman. He came and replaced a part to fix the problem. I dont have any complaint with his work but here it is, October, and the ice maker makes maybe four ice cubes at a time on a good day.I am really disappointed with this product and according to their commercials, I would like to know which of these techs are setting around doing nothing, maybe he could come and fix my fridge once and for all. I would sure find it difficult to recommend any Maytag appliance as a result of this mess. I could call a repairman myself, but I was under the impression thats what a warranty was for. According to Lowes we are required to call them and they will schedule a repairman or the warranty isnt any good. I replaced a GE French Door with this Maytag, I sure am sorry I chose this Maytag.I know an ice maker problem is minor compared to some of the complaints on this appliance, but when you pay good money for a product you have every right to expect everything about it to work. Im just wondering where these appliances are actually made?

I hate this machine: Maytag bravo xl washer. Clothes come out extremely wrinkled, drum so deep can barely reach bottom on my tip toes & Im 57 & clothes dont come out clean. I cant wait to replace it!!! Why are clothes so wrinkled, I want to hang dry things & everything has to be ironed.

Purchased new Neptune stacks in 2002 and had several service calls on our expense and we noticed the hinges on the washer door were rusting! Ordered new ones from dealer but rust continues and has spread to top of machine over the bleach dispenser. The metal is falling off! Bad rust on the inside lip under door also. I contacted Maytag when I first noticed rust and they blew me off so I contacted the local dealer we bought from and they did nothing to help. Will never buy Maytag again and have not recommended it to anyone else either. ModelINGooZES. Serial: 51867064AJ.

Just after a year the bottom freezer began to build up frost. I had to thaw it every day. A repairman changed part and ran well for about 5 months when it started to frost up again. Again, I had to call a repairman in. $500.00 later, my fridge is working again. I am done with Maytag appliances. Never again!

I am writing for your assistance with an ongoing problem that I am having with my Maytag Series 2000 front-loading clothes washing machine. I am, frankly, astonished and frustrated beyond any means of coping with the response I have gotten from Maytag about the lemon washing machine that was sold to me. As I have never before had any sort of reason to complain about any major appliance purchase (nor about any car or house purchase), I’m not yet sure of what avenues are available to me. It seems prudent to inquire of your office before getting a private attorney to help me with this. The following is my situation:First of all, I am asking for a replacement washing machine. I am clearly saddled with a lemon.On or around December 2010, we purchased the Maytag Series 2000 washing machine from Cedar Appliance of Medford, MA. Within the first several months, the washer started ripping, shredding, and putting holes in our clothes. This did not happen during every wash cycle, just sometimes. At the time, we didn’t know if it was the washer or the (also new) Maytag dryer that was causing it. After living with this for some time, we decided to call Cedar Appliance for service. Cedar came out several times to look at the machines and they couldn’t tell what machine was causing the holes. Eventually, I started examining every article coming out of the washer to determine which machine was causing the problem. Over time and many visits later, Cedar Appliance referred us to L.A.R. Service of Wakefield MA, which they called Maytag service.L.A.R. Service came out and looked at it. They said that we were missing a part. They ordered the part and installed it and said everything should be fine. They also sold us an extended service contract. I am still having the exact same problem with the machine. Today I called L.A.R. and they told me that I had to call Cedar to get an authorization for service. I called Cedar and they told me to call Maytag. I called Maytag and after spending an inordinate amount of time recalling the details, the service representative told me that I could pay up front for an extended warranty and they would send someone out. I asked for a supervisor. I got Kitty. Kitty told me that Maytag would not replace my machine, which is clearly a lemon because I hadn’t yet had enough service done on it. I explained that I have spent hours calling for service, scheduling service, waiting for service, supervising service, and paying for service. She explained that on only one service call did they install new parts, so I needed more service. So, I should have demanded new parts on each of these service calls so that I would have earned some credibility for my lemon machine?The fact is that my family and I have lost hundreds of dollars on torn and ruined clothing caused by a new washing machine! After the boot was installed, or replaced (I’m not sure exactly what was done), we are experiencing the exact same problem. When the L.A.R. Service people left last time, they told me the problem was solved. It wasn’t. This is not normal. This is a lemon machine.Its one thing to have clothes destroyed, but what is extra frustrating is that I never know when the machine is going to destroy an article of clothing. This past Friday, we were preparing to go out of town for our daughter’s basketball tournament. I took the clothes out of the washer on Friday evening to discover that one of the blue uniforms was destroyed. There was no time to replace the uniform and my daughter was out of luck. This means that I cannot put an article of clothing into the washer that I absolutely have to have. I can’t live this way. This is a relatively new washer that should last 20 years. Right now, I can’t wash any important article of clothing. I’ve been told before that it was all set. Kitty has L.A.R. coming again this Wednesday to repair the machine. What am I supposed to do when it’s repaired? Put a uniform jersey in it? This is a very brief description of the experience I have had over the past 1.5 years with this new machine. The hours, money, disappointment, and utter frustration is more than I can describe in an email. I have attached three photos of recently destroyed items. Unfortunately, I threw away tens of items several months ago when L.A.R. fixed it.Is this unbelievable? Or are my expectations too high? Is this really what Maytag/Whirlpool has in mind for customer service? Is this really what they mean by standing behind their products? Why wouldn’t or why shouldn’t Maytag replace this machine? How much more time, money, and tears is a customer expected to spend and endure? How do I regain peace of mind and quality of running a household? Am I supposed to toss this machine and buy a new one? Believe me, that’s what I will have to do if I can’t get relief on this problem. There is no way that I can go many more months with this headache. In many ways, buying a brand new machine would be worth the peace of mind, but I am trying to make sure that my family, as consumers, are treated properly. It is also the principle of the thing. Please advise on any remedies available to me here in Massachusetts and please let me know what additional details should be provided and to whom.As an aside, Maytag/Whirlpool does not seem to be doing well with their reputation on the internet regarding customer service.

I have nothing but great reviews for my Maytag experience... In approx 1975 I purchased a Maytag W&D, Model MAH4000 MDE4000, when their advertisement was portraying Maytag repairmen as the loneliest repairmen. Maytag was so dependable that the repairman was NOT needed...and it was true... That Maytag W&D set lasted til approx 1998 when it was upgraded to the Maytag Neptune MAH4000 series... Had a minor problem with mold in the washer, but Sears and Maytag replaced the seal and made another modification... We also dried the seal at the end of the washing day and left the door slightly ajar between uses... Have not again had that problem.I have since given the Neptune set to my daughter and the washer and dryer are still in operation, WORKING SUPERBLY I might add... So I am searching for a good quality Model MAH4000 and MDE4000 to replace my current much older, yet functional Whirlpool... It may need some repairs and about a year ago, I spent $173 to replace the Pump which was clogged by a sock inadvertently stuffed around the top of the drum when too many items were pushed in at one time. I prefer not to throw additional money at this machine! So, if you know of a Quality pre-owned Maytag Neptune washer and dryer in the Lexington KY area, please contact me...

Wish there was some way to secure all dishwasher under the cabinets better. It tips forward slightly, but gets caught on counter top, so it won’t fall over. The dishwasher itself is truly amazing. I love the stainless steel inside. I ensure I use the dishwasher cleaner on hottest cycle once a month. I have no odors. Both racks hold up well and the silverware tray has never given me any problems. I even like the thin little third top rack, which is where I lay my larger flat knives or spatula. As long as I use the finish dishwasher cleaner, the dishes come out sparkling. And a few times I have forgotten to fill the finish container, the dishes still sparkle. My teenagers do the dishes a few times a week. They don’t wash them off ahead of time. On occasion I have to pick a few pieces of corn or food out of the bottom, but the dishes still sparkle and the leftover food caught on the drain, well it looks clean enough to eat. I would definitely buy it again.

If you are looking for the Maytag repairman he will be at my house Tues fixing my barely 1 yrs old dishwasher. This is ridiculous to pay this amount of money for the reputation that Maytag is known for or I will say was known for. $270.00 for a control panel. My last Maytag lasted over 30 yrs. Not made in the US - not built to last and this was told to me by the people that installed it so take it for what its worth. Look elsewhere. My last Maytag product.

I bought a Bravo XL Washer 3 yrs ago for $900 to $1000. The washer started beeping and not starting to eventually not turning on. I called customer service as I was told my washer was still under warranty. They scheduled a service man to come out with a $95 charge to come out. He came and it is the user interface. Apparently, this is a huge issue with this type of washer. He told me it would be cheaper to get a new washer than to have this one fixed. I called Whirlpool/Maytag after the fact and was told the part is $422.49 to fix the washer. I explained that I was told it was still under warranty and they denied this is the case. My previous washer I had for 18 years and not problems until the end. Having a washer for 3 years and being told to purchase another one because it would be too expensive to fix the current one is very disheartening! I do not recommend this product to anyone, nor do I recommend the company as they do not try to make things right or offer any assistance in any way! Buyer Beware.

Purchased a Maytag Electric range Model MER8800FZ2 in 2019. The surface Scratched the first week of purchase and the stains will not come off. When I called customer service they claim they are not responsible for cosmetics. In my opinion, This model was put together with the cheapest material they could find. Maytag is not what it used to be. The Elements take a long time to heat up. Inside the oven, the Glazed Paint is cheap product also where once it stains with food it never comes off.

All I can say is what a mistake. Had a front loader that always smelled and had mold around rubber gasket in door. So, wanted a top loader this time after old GE died. Unbelievable, not enough water to clean clothing. Clothing comes out with some dry spots. And the worse thing is washing black items, tiny particles on black pants, shirts, etc. Think is lint not soap but not sure. You have to rub all over the clothing to try and remove. This washer is 8 months old and I have cleaned it with baking soda and vinegar mixture thinking this would help, it doesnt. The spin cycle sounds like a rocket ship taking off. Lots of banging noises during operation also. I have invested a lot of money thinking Maytag is rated high. It is a pretty grey color with glass top. Well I was fooled, not only the saying looks arent everything for people but its true for washing machines. I have gotten multiple mail from co. wanting me to get extended warranty. Think I will, usually dont, cause I think it wont be reliable. Wish I had my washer from the 70s and 80s. Plain old wringer that got things clean. Just put black pants in dryer on very low heat taken out damp cause I dont dry a lot of my clothing. This seems to have helped to remove stains (soap)/ lint. but, talk about wrinkles, oh boy, this machine has that spin cycle going 100 miles a minute. And if you pick a lower spin speed things come out wet. I actually can say I hate this Maytag Bravo. Things dont come out clean, wrinkles beyond control, very loud. Please folks check out your sites on the internet before buying Maytag.

Maytag Centennial Washer - Bought washer because of brand name and was that a mistake! This is the Loudest, noisiest, banging clanking washing machine I have ever heard. Every time I do a load of laundry the washer moves a foot from the wall and I have to continually move it back. Needless to say I hover over it all the time when I do laundry. It isnt even 2 years old and we are going to go buy a new machine, AFTER looking at reviews!!!

I bought a new Maytag washer two and half years ago. One of the new HE (High efficiency) models. Clothes do not get washed clean. But not only that, now its not washing at all. My previous machine was a Maytag...Had it for 22+ yrs. I guess Maytag quality is no longer what it used to be. Disappointed customer!

During 2018 we purchased Maytag Bravos top loader to replace antique KitchenAid. Very dissatisfied at first, but luckily found the settings that makes my machine work very well on every cycle. First add 1/2 gallon of water to empty tub. Add detergent. Set controls at: Soil Level-Heavy; Wash temp - Warm; Main dial - Bulky Sheets; Extra Rinse - ON; Fabric Softner - OFF. Can now load full tub of clothes and more detergent if desired. Press start button and water covers it entirely. It works so well now, that I went from I hate it to I love it. Been going for two perfect months with no issues. Weird but true. Hope this helps you.

Fridge Model MFF2258VEB6 - Our refrigerator is less that 2 years old and it wont make ice! The bottom of freezer is filled with water that froze. Everyday there is water on the floor. We asked at Home Depot where we purchased it and they said we need to change the filter. What filter? The owners manual is a joke. We cant figure out where the filter is located so it looks like we have to pay money to have someone come look at this. Hey, this is ridiculous. I thought Maytag had a good reputation and thats why we bought ALL Maytag appliances two years ago! Never again!

We purchased a Maytag Dryer with the lint vent on top on March 21, 2014 from ABC Warehouse in Ann Arbor, MI. Whoever engineered this does not dry clothes. Trust me, this will be the last Maytag I buy. There is lint seeping out of the top and when you clean it the lint gets all over the place therefore, my laundry room is always full of dust.

We purchased a top of the line, state of the art Maytag washer and dryer Neptune. The fill valve failed twice, flooding the first floor and the big storage room below. Thank God we were here! Now the thing halts mid-cycle and wont continue. The repairmen both said the design is messed up and they hate to work on the Neptunes.

In January 2006, we bought a Neptune washer and dryer, model# MAH5500BWW, because we thought they were superior to any other at the time. In January 2012, the washer started making a very loud noise in the spin cycle. It just kept getting louder and a technician was called in check out the problem. We were told that the bearing was going out and he found a hole in the back of the tub. He said it was not cost effective to replace the bearing and the tub and suggested that we continue to use it until we could no longer tolerate the noise. We are very unhappy with the durability of this washer, with the amount of money we paid to be going out only after 6 years of service. We have been a Maytag customer for 15 years and will never buy another Maytag appliance. We are going to replace the washer and dryer to keep a matching set and it certainly will not be a Maytag.

Purchased a Maytag Bravo. One of the worse purchases weve ever made. First the much of the clothes does not get submerged. 2nd the clothes comes out extremely wrinkled. Called the Maytag people and they explained that Im putting too much clothing in the washer. I explained Im only filling the washer half way. They explained it should be filled only a quarter of the way. What??? Do not purchase this machine.

We had a Fisher & Paykel Washer that lasted 14 years. This Maytag Bravos XL washer has been the worst machine I have ever owned. The clothes come out dirtier than ever. In todays world all technology is becoming disposable, Where is the Maytag repairman now? I have tried all of the settings, to have a decent wash. I am ready to throw this out. Lowes you need to do something about this. It may be made in America but now we know why Japanese and Korean electronics just work! Damaged Clothes/Clothes not being washed thoroughly enough are my biggest pet peeves with this washing machine.

Bought this washer back in March of 2016. This is the biggest piece of garbage that I ever came across! That washer does not clean clothes, when they are dirty. If I stand in the rain dressed in dirty clothes, they get cleaner than in the washing machine. In 5 month I have tried every possible variation of washing to no avail. I have to handwash the clothes that I wear to work in the garden, or any other dirty job, because the washing machine does not do the job! I bought that washer at ABC warehouse, I paid almost $400 for the thing, and I have to handwash my dirty clothes!!! Shame on you!!!

Dishwasher Model MDB7749SBM1 - When I returned home from work today, I noticed the cancel drain button was on and the unit was continuing to try and drain but the dishes were not clean and the cascade pod was still inside the unit unused. I then proceeded to run another cycle to clean the dishes and what happened next simply amazed me. I pressed the jet clean button, tough scrub and 2 hour delay button and thought I was all set but the start/resume button would not engage or light up at all and subsequently the cancel/drain button lit up and the unit started draining. Now the control lock and start/resume button just flashes intermittently and wont disengage. I purchased my unit along with several other new Maytag appliances when I renovated my kitchen. I guess the microwave, stove and refrigerator is next -- unit are only 29 months old. Any assistance will be greatly appreciated. Im in deep ish I guess.

I purchased a Maytag Washer & Dryer Bravos XL in 2013, the washer is already in the junk yard, the drive system failed, the bearings failed and it began to leak. The dryer had a main control board failed, I was able to purchase a new one and replace it myself. The board was made in China, the machines were assembled in Mexico. I replaced the washer with a heavy duty Speed Queen washer made in the USA!

The Maytag Maxima XL front load steam washer is awesome. Its reliable and does an amazing job. There are so many features and settings and it makes my life easier when it comes to doing laundry. My favorite feature is the allergen setting which gets rid of allergens in my fabrics.

The Maytag Bravos washing machine (Model No. MVWB75OWQ1 Type 580) is the worst Ive ever owned. The low water level obviously is not sufficient to clean the clothes as the clothes come out still dirty. I pre-treat stains carefully and follow all of the directions and 9 times out of 10, my clothes come out with the stain still there. The clothes never smell clean. In fact, they have an odor. My t-shirts still have a smell of BO under the arms and some of my clothes still smell like my perfume. They just arent clean. I feel like we put our dirty clothes in this machine and they agitate around in a little pool of water for an hour and they come out still dirty. The machine frequently gets off balance and shuts down too. If I had the money to trash this one and go buy another one - Id do it in a heartbeat. Unfortunately - Im stuck with this piece of junk until I can afford to buy a new one. This was a total waste of money and Maytag should be ashamed that they have not recalled it and given its customers a replacement option.

The machine has left pin-sized holes in finer clothing since we first used it. I had purchased the extended warranty so they were called out to repair the issue four times during the warranty. They replaced the drum, but I still get holes. I think it is because there isnt enough water to rotate the clothing and it rubs repeatedly against the same spot on the other clothing. I have a see-through lid and you can see that the clothing just moves very slightly in the same position. I separate all clothing that has a zipper or any trim that may rub against the finer fabrics, but I am still getting pin-sized holes. We requested compensation or a new machine. They extended the warranty. We have replaced enough clothing that we are now buying a new machine. It will NOT be a Maytag.

Disappointing that a Maytag would be a problem machine. Constantly out of balance when spinning and mediocre cleaning. Now it is spitting oil underneath. Am on my way to buy new machine with agitator.

The unit has an ice maker. On a regular basis, water would accumulate at the bottom of the freezer pan. When the bottom pan got filled up, water would run out on to my hardwood floor. I related the problem to the ice maker. Researching the problem, I learned that the ice maker has an adjustment for timing the on cycle for filling the ice tray. After several adjustments nothing changed. I ordered a water control valve and installed it. The problem persisted. I installed a water pressure regulator but the problem persisted. I installed a water filter, the problem persisted. I turned off the entire ice maker and the problem persisted. The problem wasnt the ice maker. The real problem was the defrost cycle of the evaporator. The drain for the water was plugged with ice. I made modifications to the design so I could monitor the drain hole in the back of the freezer. Will I purchase another Maytag… probably not?