I have purchased my top loader Bravos washing machine 3 1/2 years ago and I have had nothing but troubles with my machine. I have had to replace the motherboard twice and I constantly have that foul smell in all our clothes. I have to wash each load twice and still the smell doesnt come out. I have also complained numerous times about the water level not being correct, but they keep saying that is how the high efficiency machine is. I can watch my load washing because we have the clear lid which I like. But at the same time, it gets me really angry seeing how this doesnt clean clothes like it should. I dont believe that the water levels are right at all. I have clothes that dont even get turned over as they are washing and I have even smaller loads than before. I can only clean 4 adult pairs of jeans at one time and I still think that is too much. I clean my machine every time the red light turns on with the Affresh tablets and sometimes I run a clean cycle with just bleach. Maytag has done nothing to try and correct these problems. Its so sad that I have to take my clothes to the laundry mat to go wash them and there I have absolutely no problems. They have the HE front loaders and they have enough water to wash my clothes and I can actually see them being washed. I will never buy a Maytag washer or dryer again. How sad you have all these complaints and no one to help you fix or correct them the right way.

After two years of light use of Maytag Washer 300 Series (MHWE300VW13), it stopped working. I bought Maytag Repair Plan Plus One on Oct. 8, 2012. I scheduled a service appointment on the 9th of October and was told the broken part needed to be backordered and that I should get the parts on November 5th. I have waited for almost one month. Today is November 6th and I received an email and was told I will have to wait another month! Am I in America? There are so many complaints about Maytag washers online. Can the consumer be protected? Am I complaining to the air here?!

Bravos XL - This machine purchased in 2014 at Home Depot service plan, needed major repairs just over a year old. Tech working on this machine replaced the whole tub assy after Maytag want to just do the cheap repair and just do a bearing kit. Reading online all the hundreds and hundreds of the same complains Maytag has done nothing in good faith to replace these junk washers!! My washer is now leaking under the washer less than a year after the last repair!! My good friend purchased the same machine and has had the same issues and his has been down for weeks because the poor service person from Maytag service broke some of the new parts! Now the washer is leaking again. WHAT can be done. This not right!!! Public needs to be warned about these flawed machines and Home Depot is still promoting these Junk machines!!!

I bought a Maytag Centennial Top Loading washer 2-1/2 years ago. Its worked very well, but has started to roar so loud on high-speed spin that you have to leave that side of the house to be heard. The factory technician determined that it had a bad gearbox and that it wasnt anything I had done that caused it. He told me it was going to cost more for parts & labor than the machine was worth. I called Maytag and was told they wouldnt help me because it was after the one-year warranty. When I asked for a supervisor, he offered to pay for the parts, but not the service. Thats kind of like Chevy offering to pay for the defective engine part, but not the installation. I have never bought a major appliance (or even a hair dryer) where I thought 3 years was a reasonable life expectancy. Lifelong Maytag Customer has left the building.

We purchased a Maytag Bravos Quiet Series 300 in June 09. The dryer timer has malfunctioned since shortly after purchase, it will add time near the end of the cycle, sometimes as much as an hour or more. We have had factory authorized repair firms (tried several) attempt to fix the problem both during the original warranty and extended warranty periods. They replaced the mother board twice and the moisture sensor on another occasion. All to no avail. Maytag has been worse than useless in the whole situation, and now will do nothing. It seems our only choice is to live with it, keep replacing parts, hasnt helped yet, or buy a new dryer. You can bet it will not be a Maytag!This situation is dangerous, if left unattended when the malfunction occurs the clothes and interior of the dryer get extremely hot. It is a potential fire hazard.

Maytag Front load washer mah8700aww - This washer has been the biggest boat anchor of a machine. Nothing but trouble and bad parts. New motor after 18 months, water level sensor at 2 years, main control board twice now at 2 years and 4 years, and now it is showing signs of needing yet another main board. E3 trouble code plagues our home and basement. This machine has been leveled and re-leveled numerous times and still shakes like crazy... I mix my paint cans by setting them on the top... the best use for this machine. Yes it sits on a concrete floor. So not satisfied and will not ever buy another Maytag anything. There should be a negative star rating. It does not deserve even 1 star after being taken advantage of like we and thousands of others have been.

My name is Mrs ** and I dont have a complaint. I would to tell you about our washer. It is a Maytag. It use to be my mother-in-laws. She did laundry in it for 4 grown boys and 1 girl plus her and her husband. She passed along to my husband a long time ago. And now it does laundry for 6 kids plus my husband and me. I run it 2 days a week sometimes more. The washer is between 25 and 30 years old. And works good still. Im not sure how much longer it has but we are happy with it. And soon Ill be washing for 7 kids. We have made a decision to start looking for another soon. But I wanted to share my story with you. My husband is now in his 40s if it says how long it has lasted. Thank you.

Bought the Maytag model MFI2670XEM and within 6 weeks freezer wasnt making ice. Repairman came and fixed it, within a couple weeks same problem again. It was fixed and within a couple months same problem. Fixed, but makes very little ice. Now 18 months later after purchase freezer is leaking water onto the floor. Very disappointed!!! After reading other Maytag reviews I am worried I will have to dump this relatively new refrigerator and buy another (wont be a Maytag) and our upgraded dishwasher from Maytag is terrible! I hand wash all my dishes before putting them into the dishwasher. The smallest bit of ketchup or sauce is not washed away in the wash cycle. Our Maytag stove/oven seems to not heat correctly, as well. Internal temperature gauge reads 5-15 degrees off all the time. Thumbs down Maytag! Extremely disappointed with Maytag products! Will never buy again!

I purchased this washer three years ago. It worked fine, but all of a sudden the washer stopped spinning and was not following any of the cycles. Of course it was out of warranty. The repairman states the computer board on the washer is fried and will cost $400 to replace. Several stores have stopped selling Maytag because of quality issues. No more Maytag for me.

After only 4 years, the door handle of my $1200 range simply fell off. This seems to be a common problem with this range (Maytag Gemini Electric Double Oven), but what is inexplicable is why a part that perhaps is exposed to the most amount of pressure on a daily basis (opening and closing the oven door) would be held on with a plastic fitting! It seems like planned obsolescence to me. Apparently, the part is $100 (once shipping is included) from Maytag and for that I get the pleasure of taking the entire door apart to install it! Garbage.

Freezer does not freeze well. Causes most our food to get freezer burned. We tried turning it up and down but made no difference. Actually went and bought a separate freezer for meats.

I remodeled my kitchen, put in all new Maytag Almond appliances washer, dryer, stove, refrigerator, dishwasher and microwave oven. I was pleased with everything but the stove. The stove was $800.00. The oven caught fire three times and smoked up my house. I replaced the stove with another brand, cheaper and safer. I moved to a new house, five years later, bought all Maytag appliances stainless steel. The hinge on the deli tray broke, the inside is thin plastic, not covered in extended warranty. The stove caught fire (I didnt learn the first time around)! The microwave has a thin, bendable, plastic rack, the handle snapped right off. I cant buy a handle separate from the door. Now the microwave wont heat! My dishwasher was recalled. The heating element could have caused a fire! Nothing that breaks or malfunctions is covered by warranty. Who needs to pay for a warranty too and get no parts or service rendered! I will buy all new appliances and when I do, it wont be anything Maytag makes and none of their other brands! This stuff is very expensive garbage! Somebody please initiate a class action suit!

We bought a new Maytag electric range from a local dealer three years ago. The oven element quit working, which shorted out the motherboard that controls the entire range. The cost of repair was $500 for the element, motherboard and installation. We have owned other brands that lasted 20 years and worked fine with no repairs. My folks have used Maytag for over 50 years with no problems. Who and where is this junk manufactured now? China? I will never buy another Maytag product!

Had Maytags since we got married (57 yrs). The first one lasted over 30 years, the second about 15 years, then got a Kenmore that washed beautifully, but lasted 3 years. Have a newer Maytag now that is supposed to be more efficient, but takes forever to wash a load. The biggest disappointment with new appliances is there is no timer to let you know what is happening during the cycle.

We bought our Maytag dishwasher at Sears about 2 years ago. It has never cleaned very well, we have to rinse everything almost to the point of spotless before we load it. Its a water saver, which means it takes more than 4 hours to fully cycle. Just today, I went to turn it on and the start button does not work. I looked it up and found that this is a common problem with new Maytag washers. This is really irritating, considering we paid a lot more for the Maytag brand than we would have paid for something without the Maytag reputation. Live and learn, I guess; we certainly will not be buying another Maytag.

On 11-10-10 I purchased a top of the line Maytag fridge. All had been great till we needed a part in Nov. of 2014! After nearly 3 months of searching they tell us that they no longer make parts for this unit and I am out of luck! Fridge works great but the center seal is broken (french door - Mullin) they quit making the part???? I am beyond angry! Will never buy Maytag again!!!

It meets all of my needs and expectations. Its quiet looks nice and does a very good job of cleaning dishes.

My new fridge iced over top to bottom. It started making horrible noise then ice maker stopped working. Called MY repairman. Thats when I found out about all the ice. He told me to thaw out and hed be back. It thawed out and then freezer went out. ALL my freaking meats and frozen food had to be thrown out. Now water keeps Flowing out on my NEW tile! Called my repairman back. He came back then informed me it was junk! He said several other customers having same issue. My daughter has the same refrigerator and it broke down just like mine! My repairman also said a big issue with your junk was you used parts from other brands to fix!After reading all these complaints I can see no sense in calling to get it repaired. Its obvious we are all having the same issue. Maybe someone from your ** company could check them out. I dont have the money to buy another fridge! My 85 year old uncle with Alzheimers lives with me and I dont want him to slip on that water and hurt himself! I think all of these complaints need to go to BBB. Thats my next step. I believe you need to recall this junk or give us our money back! I need you to respond or Im going on blast to let everyone know how you treat your customers.

We had this washer 16 months. We bought it new from Home Depot. The clothes came out with spots on them, white residue and grease spots. This was ongoing for awhile. The bearings went out after 6 months. It was so loud now the water pump went out. I was told by Whirlpool (they bought out Maytag) that water pump is on back order and could take a couple of months!! To fix the bearings and the water pump was almost 700.00. A new washer is 1000.00. We junked it and had to buy a new washer GE. We are sick about this waste of money!!! What a piece of JUNK this Maytag Bravos XL is!! We need to have a class action suit and try to get something back. This is ridiculous and they arent taking responsibility. Whirlpool/Maytag are rip offs!!!!

Purchased a new Maytag washer top load/Dryer set on April 1, 2016. Having trouble uploading receipt but I paid 1,145.83 for set. It took 2 weeks to get it delivered on April 15. 1st use it shook and wobbled even though the load was balanced but Ive read that is a problem with these machines. 1st load of clothes, washer didnt fill with enough water to wash properly - 3-4 inches of water for a full load of jeans. Top 2/3 of clothes hardly got wet! Changed the setting, same problem. Changed the setting again, same problem. I had to stand at washing machine and keep lifting the lid to get more water in the machine. Clothes didnt rotate in machine so all the clothes on top half didnt get cleaned. The spin cycle is scary! You could hear clunking noises and it had nothing to do with load being balanced. Did a small load and same thing with water level and spin cycle. Called Home Depot to pick up both machines on next business day. The dryer lint trap is so long, it made a mess trying to remove the lint even after only 1 load. NEVER AGAIN MAYTAG! Ive never regretted an appliance purchase like I do now. Maytag and April Fools day are a perfect match. Only its for real and not a joke.

I am also frustrated with Maytag for the same exact problem... The control panel and the dishwasher not working just after our year warranty went out. I purchased this product because we had a good experience with a Maytag Dishwasher lasting about 20 years, only to get fooled that the quality is not there any longer. This seems like BAD business on Maytag, Whirlpool, and Home Depot! How can we get an official complaint to someone who can fix this? Another example of big businesses that do not care to take care of customers! Why would a company like Home Depot continue to support this business!!

This washer ( MHW3505FW) leaks, is crazy loud, water wont drain, clothes smell bad after washing, defective drain pump, defective mother board. Only had 2 1/2 months and it broke. Maytag refused to refund me and Lowes refused as well. Thankfully I paid by credit card. Am disputing the charge. Terrible washer should be recalled. Many complaints on this washer. Very disappointed and upset.

I had a stackable Maytag dryer that was bought in 2016 but only used during the summer of 2017. Last May the dryer stopped heating. I contacted Maytag and they sent a repairman a week or so later. He identified the problem in the electronic control and ordered a replacement part. The part came and he installed it a week later. The part was faulty and he ordered a replacement for the replacement. It arrived a week later and also did not work. He said he had problems with replacement parts but contacted the technical service department at Maytag as he did the first time. The technical service person said there were problems associated with new software being not compatible with dryers in the last year and we needed a new control panel. I contacted Maytag again waiting the usual hour to get through on the phone. They agreed to replace the parts for free and ordered a control panel that arrived a week later. The technician installed both parts but they did not work. I contacted Maytag again and after waiting the required hour talked to a person who said she would contact the department who could arrange a replacement. They contacted me a few days later and said they would supply a replacement for $250. This was delivered a week or so later but they did not have a stacking kit and returned to the delivery company with the dryer. A week later they returned with the stacking kit but forgot the dryer. A week later they returned with both the dryer and stacking kit but the installer (always a different person) said he was too big to get in the space behind the dryer and that the venting supplied was wrong.I bought new venting from Home Depot and a new installer arrived a week later. He said the new venting was not necessary and in fact wrong and installed the dryer. It ran but foolishly I did not check to see if it heated and neither did the installers or if they did took off without letting me know that the dryer, like the one that was replaced did not heat. I discovered this a couple of days later when I tried to use it. I contacted Maytag and they setup an appointment for a new service technician to visit. I contacted Maytag again today hoping to get some explanation of what might happen next or some explanation. They had no idea but did inform me that they would not replace the new dryer but would start repairs again.

We lost our home in a tornado in 2005 and had to buy all new appliances. So, I bought a Maytag Neptune front load washer and dryer. It was my 1st ever. I will never buy another Maytag appliance again. Just at the end of the 5th year going into the 6th year, the bearings started to go. So, I checked with the place where we bought it and was told how expensive it would be to fix. It was anywhere between $500.00 and $700.00. Well, thats crazy. I therefore e-mailed Maytag numerous times and was thanked for my complaint. But they offered no help with this matter. If they dont back their stuff at all, why would I want to buy their stuff? They could have at least offered to help with it. There are only 2 people living in this house and there is no excuse why that washer should start failing already. If I thought it was worth it, I would load it up and drop it off at a Maytag store and leave it there. It still runs. But it makes an awful noise and we are just waiting for it to crap out. I am going to try to sell it for as much as I can get out of it, hopefully before it completely stops. Maybe some fix-it guy would want it. Well tell him whats wrong and they can fix it and sell it to some other poor person. I lost my job in January. Therefore, I cant afford that much to fix it. So, I will now have to try to find something used, because Maytag does not back their stuff. I would rate this machine lower if I could, but that wasnt an option.

The washer is so loud it can be heard all over my home (my home is 2700 sq.). It sounds like metal to metal grinding. I was told thats how the run and the first bit of water isnt enough to even wet the clothes. Id never buy another one (even though this is my 3rd Maytag washer. Im 78 yrs.old).

I had a Maytag dishwasher that I purchased around 2005. I had no issues with it at all. Then, I got a notice that it was being recalled due to a fire hazard. My options were to either get a repairman to come out and fix it, or get a credit towards a purchase of a new dishwasher. I chose the second option. Even after getting a credit, the purchase cost was way more than my original dishwasher. I purchased the new dishwasher in June of 2010. Last spring (May 2012), I noticed a gap in my hardwood floors around the sink. A flooring rep looked around and said he would bet that theres a leak either at the sink or the dishwasher. I took off the front kick-plate to the dishwasher and discovered a wet spot. I monitored that area and discovered the leak coming from under the dishwasher (around the float switch). It wouldnt leak all the time, but every now and then, it would leak half to a full cup of water. I had the hardwood floor fixed (cost $350). At the same time, I schedule a service repair through Maytag. They sent a rep from a local repair company (Convenient Appliance Service, Inc.). The service rep couldnt identify the cause of the leak but said it was more than likely the seal around the door. So, I paid another $160 to get the repair done. I monitored the leak for a week and had no problems, so I put the kick-plate back on. In September 2012, I noticed a wet spot in front of the dishwasher. I took off the kick-plate and discovered that the dishwasher was leaking again. This time the leak was worse. It would leak 1 to 2 cups of water during a wash cycle. I called the repair company and they came out free of charge to take a look at it. The service rep said the float switch had gunk build up in it. He cleaned it out and said that should fix the problem. I monitored the area for 2 weeks and everything seemed to be fine. Last week (March 2013), I noticed some gaps in the hardwood flooring around the sink and dishwasher. I pulled off the kick-plate and discovered a wet spot. I ran the dishwasher and discovered that it leaked a ton of water (over 4 cups). I contacted the repair company that came out last time, and they said they would have to charge me $100 plus to come out and take a look at the problem. The rep recommended contacting Maytag. I contacted Maytag and they said I would either have to pay $129 for a service call (not including cost for parts), or $269 to get covered under their Repair Plus 1 program (everythings covered and it adds 1 year of warranty my dishwasher). I asked at what point Maytag would replace a dishwasher. The rep said when it is deemed unfixable. Other than that, they just keep coming out if I have issues. Part of me thought I need to cut my losses and just rip out the dishwasher and get a new one (cost somewhere around $700). But I went with the Repair Plus 1 program in hopes that they can resolve the issue. But Im definitely going to have to get the hardwoods ripped out again. It looks worse than before. It’s probably going to run another $500.

I have had the Maytag Bravos washer since November 2010. This washer does not clean clothes. They are never even submerged in water. Had I known this, I would never have purchased it. The salesman at Sears surely didnt mention it. I remember being disappointed at the fact that there wasnt a washer in the place with an agitator. I am disgusted with the washer and the company. I realized that it has been over 12 months since we purchased it, but most people do not feel the need to investigate what is going on under the lid of their washer. I unfortunately assumed that the washer was going to wash! Silly me. No, it does a little spin spin and a little spritz of water (literally, thats it) and at the end, you are left with funk concentrated in the creases of your twisted up, stinky clothes. No agitator plus no water equals no clean! The smell is awful. Someone else described it best - a mildewy basement.Anyone else who is claiming that their clothes do not stink with this machine are surely being deceived by strong perfumes in their detergent and fabric softener. To get a true idea of what their clothes really smell like, they should wash a few times with a scoop of borax and no fabric softener. Then tell us how they smell. I am convinced that the entire line of HE washers is a sophisticated line of crap! They use such small amounts of detergent because that little bit of water going into it will not get any more soap out, much less sweat, dirt and lots of other nasty stuff. This may not be a big deal to other people, but it is huge to me. We have a small homestead. Our clothes get dirty. We spent several hundred dollars of hard earned money on a name we trusted and they do not care.Every load, every day, I am reminded of this fact and it infuriates me. Im not typically one to write in complaints, but as an American citizen where there is a free market (somewhat), I have an obligation. If a product is really good, the makers deserve my praise. Likewise, if the product is really bad, the makers (and refuses to compensate in any way) deserve my complaint, as do my hardworking fellow Americans shopping around for a new washer. Stay away from Maytag and if at all possible, stay away from HE machines. It is so true that they dont make them like they used to.PS: Maytag tried to blame this issue on government regulation when I called. Im sick of this passing the buck. I am fully aware of the chokehold government regulations have on business, but they only hurt small business. To act as if this is not a partnership between the government and big business (like Maytag) only adds insult to injury. Take a look at the money spent lobbying by this company. Disgusting. The good news is, any success they currently enjoy will not last.

Sounds wonderful. Thats what I thought when I let my son have my 20-year-old, still running older washer. I wanted a new one. It worked good for 3 years and then one night I went to throw the clothes in the dryer and its full of water. After the last rinse and spin, it filled again and stopped. So I tried it on every cycle and got the same results. I thought, No problem. We have a great, honest repairman. Ill call him the next day and hell fix it. When I called and told him what type of washer it was, he was surprised it was working at all. Seems they had a problem with water leaking into the transmission. Apparently, I was lucky that mine had worked for as long as it did. Like I said, Im lucky to have an honest repairman. He told me he could charge me to put in a new timer and solve that problem, but I shouldnt waste my money since it is just a matter of time before it goes bad. Seems they were all bad and Maytag never made good on them. Told me the smartest thing to do would just to go ahead, bite the bullet and get another. It will be here Tuesday morning. Hopefully, this will be the last one I have to buy (keeping my fingers crossed since I had hoped the Maytag was going to be the last). My old machine is still running great for my son. Over 30 years my repairman has had to fix quite a few things for me - ice makers, dishwashers and even a timer on my old washer. Thank goodness he was honest enough to not fix my washer. I dont know if there are even any Maytag products around now, but if there are, they will never get my business. I spent a fortune on a machine that should have lasted the rest of my life. Ive had childs toys that lasted longer. My advice is do not buy Maytag.

We bought this stove in 2014. One knob got stuck while my teenager was cooking food on the gas stove. He called me at work worried because he couldnt turn it off. My husband left work right away to go home. We thought it was just a bad plastic knob. Now a second knob is stuck in the on low position. There is a third knob that feels hard to turn. That will be 3 burners. This is ridiculous. Its a safety hazard. We consumers have to worry if the house will burn down, get CO2 in the air, and if our family and children are safe. We thought Maytag was a good appliance. I will not buy another Maytag. They should recall this stove top/oven. I have read so many of the same complaint on this website as well as online in general. I cant believe they continue to sell this with this much of a safety issue. Please take it off the market.

Maytag Centennial commercial technology washer - Bought what I thought would be a great washer given the Maytag brand about 3 years ago. Started out ok But has gotten progressively louder and noisier. We cant even hear the television on the next floor of the house when the washer is running ridiculous. Now it wont work at all. Outside of warranty and a real pain. Not sure what to do but if I have to buy a new one its not going to be Ay

Not only is the dryer junk, so is Maytag support and service. I have owned this dryer for 2 years; my previous dryers lasted about 20 years each. This one is on its 4th service call, none of which are apparently under warranty (well, except the first one). From what the techs who come out here tell me, the design and build are both poor. I will never own another one of these; if I can stretch it out one more year, then well replace it.For now, the drum wont turn. There is a nylon support bushing (and possibly more) that degrades immediately upon use. There are only two of us, with about 3-4 loads per week. This was supposed to be Commercial Technology. The only thing commercial about it is that you have to rely on commercial laundries to get the drying done. It is good that the drum has a 10 year warranty - it will make a nice planter out by the front gate.

I purchased a new Maytag dishwasher (model #MDB4651awb3) for $300, in December of 2009. Seven months later, the dishwasher refused to start. Some lights on the front panel would remain on, while others would not respond. The Maytag repairman made a house call and replaced the front control panel, and vent. After the repair, the dishwasher worked fine for nine months. Then, the same thing happened again. It refused to start with the same front panel light problem. I called Maytag, and since the machine was now past the one year warranty, they wanted $275 for an additional 1 year warranty, to repair the machine. Since I can buy a similar new machine for $25 more, and felt this was now an ongoing problem, (it would be the third panel in less than two years). I expected Maytag to offer more to take care of their lemon problem. Since they refused to reconcile the situation, they obviously no longer stand by their machines. I will no longer buy Maytag/ Whirlpool machines, and do not recommend them.

We purchased a Maytag Bravos Quiet 300 about 8 months ago and it will not clean anything. Not one setting will make this machine clean. You have to wash everything 2 to 3 times. There is no savings of any kind with this machine and I dont know anyone who has the time to wash everything multiple times. Its all about the water; its about as much as you can spit. I ran a hose from the faucet and added 8 gallons about 10 minutes into the wash cycle and was able to clean (float) a set of sheets. I find this energy star machine to be worthless and I would have been better buying an old machine at a garage sale than this Bravos machine. Junk. If you cant float your cloths folks, you might as well be rubbing them on a rock.

I am fairly happy with this ranges performance. I do have a couple of issues on the design. I would like to be able to simmer at a lower temp on a front burner, as I use a large stock pot and a pressure canner occasionally. The smaller BTU burners are on the back and the large pots do not fit over them. I havent noticed any problems with the upper ovens performance...seems to do what I ask it to, including the broiler. I have not tried the lower oven or the convection feature at all yet. Nor have I had to use the self-cleaning feature, yet...almost afraid to after reading other peoples nightmares, though.My biggest concern is the lack of safety with the knobs on the front of the stove top. Several times, the gas has been turned on by my cat simply walking across the front of the stove and stepping on a knob. This allows gas to leak until I notice. It happened again early this morning just before 4:00 am. I was awakened by a smell, which I thought was a dead mouse somewhere (we live in the country in a 100 year old house - mice do get in, thus the cats). I searched the whole house, looking for a dead mouse, until I finally walked into the kitchen and heard the hissing from the stove. Im glad I didnt try to light a candle while I was still thinking dead mouse!After turning off the gas and removing all of the knobs, I opened all the windows to let the house air out. I SHOULD NOT have to remove the knobs every time my stove is not being used! You do have to depress the knobs slightly to ignite the burners, but its too easy. Obviously, the simple act of a little cat putting its paw on the knob is enough to open the gas. This is a serious flaw that could kill someone! Something needs to be done to correct this before someone is killed or a house full of propane or natural gas is ignited and explodes!!! I will be reporting this to Maytag and hope that they will voluntarily issue a recall to have this problem fixed...Wish me luck.

Im totally done with the Maytag brand that Ive trusted for over 30 years. I never knew until yesterday via Facebook friends that they are not true Maytag-made anymore. They were bought out by Whirlpool eight years ago. I bought my top-load Maytag Bravo 400 Series Washer ($1,028) at Home Depot in October 2008. No problems with it until now, less than 4 years old with error code DL. So I looked in the book and found it was the lid lock (the little red light wasnt lighting up when closing the lid, which prevents it from running).I made an online appointment with Sears Home Appliance repair to check it out. But after talking with online friends and googling fix videos, I was able to get it running today by taking the top off, unplugging the lid wire and plugging it back in. So far, its working but now I will fear each time I go to use it that something else will fail. My old Maytags (washer and dryer) bought in the 80s never needed service until they approached the 14- to 15-year mark. That only tells me that the newer made appliances are total junk! So many complaints and how the companies dont back their appliances, it just sickens me.

I have a Maytag washer and dryer. The washer is a top loader with a metal drum. You can hardly hear the washer while it is running, and I have had no problems whatsoever in the past six years of ownership.

Maytag side-by-side fridge with water/ice dispenser (Model # MSD2572VEW00) was purchased in 2011. Mechanically, fridge is working, however, every piece of plastic inside the refrigerator section (the regular glass shelves with plastic rims, vegetable bins, and door ban shelves) are all cracking and falling apart. Additionally, the buttons on the ice/water dispenser fell off, exposing the actual buttons on the panel. All three of the regular sized shelves have severe cracks in the plastic that affect the sturdiness of the shelf. Both vegetable drawers are badly cracked, falling apart and one doesnt even stay secure on the track. Even all three of the door ban shelves are cracked with fractures along the sides and bottom. Weve resorted to putting clear packing tape just to hold the shelves together.We contacted Whirlpool, who owns Maytag and because our fridge is 4 years outside of the 1 year warranty, they could do nothing for us. In over 30 years of owning refrigerators, this is the first time Ive seen every shelf and bin crack the way this fridge has and in less than 5 years no less! Whirlpools solution to our issue was to send my call to their Parts Department. The total cost to replace all the cracked shelves, bin drawers plus the ice/water dispenser panel is $702.28. No thanks, thats as much as a new fridge. Whirlpool should be utterly ashamed of their total lack of Customer Satisfaction by distributing such a piece of junk. Who would have thought that an appliance costing a couple hundred dollars would be considered as disposable as an aluminum pan and in only 5 years! One thing is for sure, I will certainly think carefully again on ever buying another Whirlpool product again since they are so apt to take my money only for me to repurchase an expensive appliance again in less than 5 years.

I purchased this Atlantis dryer several years ago. To this day, I have replaced the rollers and drum three times. What a piece of junk! This will be the last Maytag I ever own.

Dishwasher MDB7749SBM - Have the same problem as everyone else, panel board (2nd one, 1st was under warranty). This panel W10475787 is 2 years old. Keeps lighting up doing what it wants to do. Dishwasher is 3 years old. Cant find out if there is a recall on this part (there should be).

I purchased a Maytag dishwasher at Home Depot in October 2009. Recently, it made noises for a few months of laboring, and finally would not start.Maytag said it’s out of warranty and wanted $125 just to diagnose. Took it to my shop for $60 to diagnose and they found a faulty control panel.

I have a Maytag purchased about a year ago. My old Maytag lasted 16 years. The salesman told us that they are now built to last 8 years. It’s pretty noisy, so much so that I have to close the door to the utility room. I guess it gets the clothes clean but it used very little water. Fortunately my model has an agitator but nothing like the old kind. After looking at many models, I feel this was the best choice for the value. It is top loading which I like.

Well, Im confused and nervous! Ive read the reviews and I LOVE my Bravos washer - cleans unbelievable, its quiet, no rattling of pipes. My daughter was highly impressed when she was visiting with her daughters. She told me my washer got stains out of her kids clothes that her washer could not! Im confused because of the number of bad reviews for this washer - maybe they changed the washer? Mine is about 3 years old and I am SO happy with it! No agitator, but cleans so well. Terrified if it dies on me, I wont be able to replace it.

The Maytag Bravos washing machine may well be the worst appliance available for purchase. Sure it is a high efficiency machine that saves on water -- the clothes are often still dry when the complete cycle is finished. Many times there is still soap residue on the clothes. Forget cleaning anything with any amount of dirt on it because it seems as though items are even more filthy after washing them. I have tried everything the company advised and still my clothes are not clean. My advice... please do not purchase this machine. You would be better off taking your clothes to a river and beating them on a rock. #wearingdirtyclothesforever

Bought this Maytag Bravo washer in 2013 expecting long service life like I had with my previous machine. After 2 years spin cycle noise got progressively worse. Until now it roars loudly and keeps stopping in the spin cycle for rebalancing. Called Maytag. Experience was as described as others have reported with them and their repair service. Absolutely no help unless I spend another $310 for extended warranty to cover the $380 part (tub and bearing - 1 unit - cant get only the bearing). Paid $800 for the washer now more for the repair wanted. $1100-$1200 for a machine that will need repair again in a couple of years? Dont think so. This machine is only good for a boat anchor. Going out today to buy a replacement for $400 and it wont be a Maytag or its affiliates brand. Feel like a class action suit would be good for Maytag to wake up to.

In July 2006, we purchased a Neptune Washer. The only problem we had with it is it does NOT spin the water out of the clothes after the wash cycle. This has been going on for about 4 years. In February 2012, we had a service person to examine the washer. According to the service person, there is nothing wrong with the washer. He said to put in clothing of the same type: All towels, all jeans, all pillowcases, etc. This is not the real world. This cost me a service call with no solution. On June 10, I called Maytag on my issues. They have no recalls or issues with this washer. They recommended another service call which I refused. I even offered the washer free of charge to the person I was talking to, but did not get a response. Never again will I purchase a product from this company.

I had my Maytag washer and dryer just barely over 30 days. My washer sounded awful and I had to get a new motor. Then my clothes would come out with dry spots. Not enough water. The computer was replaced and within a few months of purchase, all the major parts of my washer were replaced. I hate it! My clothes still come out with dry spots and it is loud. Worst major purchase I made. Dryer so far has been ok.

Purchased my Maytag in November of 2010, with the freezer on bottom. Within 1 year the ice maker stopped working, and every 8 to 10 days it gets a sheet of ice on the bottom, and water runs out all over the floor. Guess, Yes the warranty expired and scared to death that Im gonna have to replace my floor. If there is a class action suit out there please inform me.

I have called this company several times. Most of the time, they tell you that you need to call another department...which means you spend even more time on hold. This washing machine is only 3 years old. I will never buy another Maytag/Whirlpool product again!

Since day one, no matter the size of the load or how careful I place the clothes or what level or water, washer vibrates and moves around the floor. I have had service out twice to recheck level but it still vibrates. Worst washer ever. I should have spent the money to repair my 20-year-old Kenmore.

I bought a Maytag dishwasher from Home Depot August 2018 and it has leaked soapy water every 3 out of 5 times that I run it. Home Depot said they dont cover installs after 2 weeks and to directly contact the manufacturer for service. Maytag sent out a tech 3 times but they werent able to replicate the problem, so nothing has been done to fix the dishwasher even though Ive shown the tech different photos of the dishwasher leaking. The service tech said they will now charge me $90 to return, even though the dishwasher is still under warranty and not repaired! Ive owned many different dishwashers (rentals and houses) without any problems. This is the first Maytag brand and it is horrible. I will never buy another Maytag and have warned all of my friends and family.

I purchased a Maytag Centennial washer a few years ago. In my opinion it hasnt worked properly from the start. We went on the low end of price, because we spent a small fortune for GE products that broke after a year and a half. This Maytag hasnt been a much better experience. First it didnt drain and spin clothes, and I was told I was using too much soap. Cut back on the soap and it started working better and going through the full cycle but the clothes never felt or smelled fresh and clean. Now 2 1/2 years in, it doesnt complete the full cycle on its own, AND there is dirt in my washer after every load. My clothes come out with streaks of dirt on them. The picture below is of a pillow case I just took out of the wash! Ive cleaned the washer multiple times, but it doesnt drain properly so it doesnt help. Maytag charges a service fee just to come out and troubleshoot and charges you again to come and do the repair. Im running out of reputable companies these days with washers.

We bought this refrigerator one year & 3 months ago & we have had various issues that are now no longer covered under the warranty. The pantry drawer has a peg on the side that is plastic & broke off on the right side. Will have to replace the whole right side panel. One of the door handles is coming loose which should be an easy fix, but its just annoying that it happened at all. Now the control panel is reading OFF/OFF & isnt responding at all. Tried unplugging for 10 secs, then plug it back in, but no luck. I cannot find any info online regarding this issue, so we will have to call Maytag. Hopefully, there is an easy resolution to this problem & we wont have to buy a new motherboard.

Had side-by-side refrigerator for over 12 months - Went completely dead - Would need $500 work!!!!! Just got less 6 months. Now need filter for water and air filter!!!!!! I wish I can give it less than one star!!!!

Dryer wont dry/ service at dead end. So in 2018 we purchased a Maytag Bravos washer/dryer set. The washer does its job, it washes clothes acceptably. The dryer, which has the sole purpose of drying clothes, DOES NOT dry clothes. It leaves each and every load damp. Two to three cycles are required for even the lightest fabrics to dry. This has been the case since the product was new. After repeated attempts to have the dryer replaced, I am fed up with the whole run around. MORAL OF THE STORY IS DO NOT BUY MAYTAG.

In a way, l feel fortunate and you will read why in a minute. l have been reading Maytag complaints specifically looking to see if what happened to me has happened to others. Apparently, it has. We purchased our Maytag range, model MER57750AB, in 2005. We too have had some repairs done under warranty. Unfortunately, we live in a day and age where technology isnt always our friend. The old appliances that were not electronically driven lasted forever; todays appliances do not. However, when something with potentially serious consequences happens that is not technology related, it rates in the who is the idiot who designed that? category. I am talking about the exploding exterior glass oven doors.Two weeks ago, the oven door handle on our range came unscrewed on one side. I continued using the appliance, planning on repairing it myself when l found the time. (I used to tinker around the garage with my dad when I was little and therefore, I have great repair skills in several areas.) Last week, I was standing in front of the stove when all of a sudden, the glass panel dropped from the door! It landed straight up on the floor and fell forward so the top edge of the glass landed on my toes (the toes that I had surgery on for six hammertoes last November and are still sore!). Needless to say, l was shocked that this happened, and even more so, I was grateful that it did not break or either of my two grandbabies were around at the time. Then, I looked at the glass and saw that it was attached to the door using only eight small pieces of double sided sticky mounting foam. I mean small! As I said before, idiot! Did they not think that the heat from the oven would eventually wear out the ability of the tape to do its job? I gave up reading after I found enough complaints about the mishaps with the glass on the oven doors to realize that there is a definite problem here. I did not see where the glass fell intact, as mine did. Therefore, I am suggesting that the exploding glass panels more than likely gave way, as mine did, and shattered when they hit the floor. Should there be a product recall for this? Absolutely! The question is how does a recall get put in motion? As others have stated, this could have been a horrible disaster had little ones been around. I pray that doesnt happen to anyone.

All I can say is what a mistake. Had a front loader that always smelled and had mold around rubber gasket in door. So, wanted a top loader this time after old GE died. Unbelievable, not enough water to clean clothing. Clothing comes out with some dry spots. And the worse thing is washing black items, tiny particles on black pants, shirts, etc. Think is lint not soap but not sure. You have to rub all over the clothing to try and remove. This washer is 8 months old and I have cleaned it with baking soda and vinegar mixture thinking this would help, it doesnt. The spin cycle sounds like a rocket ship taking off. Lots of banging noises during operation also. I have invested a lot of money thinking Maytag is rated high. It is a pretty grey color with glass top. Well I was fooled, not only the saying looks arent everything for people but its true for washing machines. I have gotten multiple mail from co. wanting me to get extended warranty. Think I will, usually dont, cause I think it wont be reliable. Wish I had my washer from the 70s and 80s. Plain old wringer that got things clean. Just put black pants in dryer on very low heat taken out damp cause I dont dry a lot of my clothing. This seems to have helped to remove stains (soap)/ lint. but, talk about wrinkles, oh boy, this machine has that spin cycle going 100 miles a minute. And if you pick a lower spin speed things come out wet. I actually can say I hate this Maytag Bravo. Things dont come out clean, wrinkles beyond control, very loud. Please folks check out your sites on the internet before buying Maytag.

Bought this machine with the intention of having at LEAST 10 problem free years with it. Its a Maytag after all. Not an unreasonable expectation. Within the first 2 years, the machine sounded like the bearings were going out (heavy, grinding noises when it shifted gears). Repairman came, replaced the entire drum (only way to get to the gears, I guess). Didnt fix a thing. Then the rinse and spin cycle on ANY wash cycle randomly quits. Just stops. Full load of wet, soapy clothes, sitting in the tub while an LD error code quietly flashes.Its not uncommon for it to take two full days of screwing around with this machine to get one load of clothes done. Have to UNPLUG the machine, let it sit for about an hour, and try again. It is the biggest waste of money ever and I will NEVER buy another Maytag nothing. Contacted Maytag and they recommended I call a repairman...REALLY? REALLY? Gee, I wish I had thought of that. Repair guy has been to my house so damn many times for this machine, we are now friends on Facebook. Dont waste your money on this machine.

Belt broke in inside under tub after 13 months $150. Now another year and I am getting an error message F51 and it stops washing. Im done. Old Maytag lasted 14 years. This is done in 2. Im not paying any more to have it fixed for whatever F51 is. Im cutting my losses now. Hate this machine the way it washes anyway. Always feel like its gonna take off for Mars to join Matt Damon. HA. I try to laugh to stop being mad. Dont buy these. It gets no stars. And after reading other reviews, it deserves none. Shame on this company! Ugh, its making me put a star rating. But I say none.

I purchased a Maytag range with self-clean oven. Manual says to put 2 cups of water to self-clean and no cleaning is done. I called Maytag and they said it is environmentally friendly and the rest of baking stains I have to scrub myself. This is totally unacceptable. I also cannot clean with easy off, it will damage the inside of the oven according to Maytag customer service. I do a lot of baking. What am I supposed to do now, live and cook with a dirty oven! Ugh!

Im furious beyond belief with Maytag. Im furious at myself for being stupid enough to purchase all new Maytag appliances when I purchased this home as I had horrible experiences with them in my former home. This concerns the Maytag over the range microwave oven model MMV4205AA. First of all, within 6 or 7 months after purchasing it while cooking a frozen dinner, the turntable just cracked in half. Maytag wanted $89 to replace it. I knew when the turntable cracked that there were more issues to come. That is not normal in any way for that to occur in a microwave.Problems continued, of course, and with each call to Maytag, they would say the same thing the microwave is out of warranty and refused to assist me. Its not some little table top thing that one can just toss out and buy a new one. I paid about $400 for it from Home Depot. Last week, without it even being turned on, it just stopped working. I checked the electrical supply and conduit to make sure that was okay. I called numerous service organizations who told me this sudden breakdown when the microwave isnt even turned on is a known issue with this model and several other Maytag over the range models. Ive called them (Maytag) three times in the last week and they refuse to provide any allowance and hear the same old thing, the microwave is out of warranty. I was willing to have them even just provide some assistance rather than replace the microwave. Ive been told by numerous service organizations that this is a known issue and that even if they repair it, it will occur again and again and Im best off purchasing a different brand, which I cannot afford. They gave me phone numbers for service organizations authorized to service Maytag products and this just goes to show how out of touch they are. They gave me one that isnt even in business anymore. How professional, not!Warning: Purchase Maytag at your own risk. I give you fair warning. Every single Maytag product Ive ever owned has been a problem. I will never, ever, ever purchase another Maytag product again. I would think just out of decent customer relations, that theyd repair this issue. To be honest, I dont really trust a repair as Ive been told it will happen again and again. There was no notice that the microwave was breaking down either. It wasnt turned on. One day, I went to use it and it just wouldnt work. Actually, I went to use the timer on it and thats how I found out it was dust. My advice is stay away from Maytag. If you read reports, there are more complaints on Maytag than any other appliance manufacturer in existence. Not only on their products, but their customer service too.

Bought a new Maytag High Efficiency washer. I followed the directions closely, using the proper type and amount of soap, and the proper settings for the soil level. The clothes come out of the washer smelling almost the same way they went in. I contacted Maytag by email. Their response was to send me instructions on how to operate the washer. I responded again. Their response was basically Sucks to be you. This is the worst washer Ive ever owned, and the customer service is truly awful.

Bought mdb7609aww2 dishwasher in 2010. Now I cant use it as it will not start even though the panel lights of my selected wash cycle work. I looked up on internet how to reset it, but I only get a half cycle. Called customer service and for $269, I can get it fixed and get a one-year warranty. Wow, what a deal. Might as well get a new dishwasher. Joining the lawsuit. It is about time corporations take responsibility for defective merchandise, not make money to correct their mistakes by charging customers for overpriced parts and stupid worthless warranties. A pox on them.

We purchased a Maytag dishwasher from Home Depot in January 2009. We did not begin using it until perhaps March of 2009, so just over 2 years ago. It gets ran maybe 1 to 2 times per week. I went to turn it on a day ago and the right side of the control panel, where you press the start button, does not work. When I checked Maytags website, I discovered there was a recall due to the heating element. So, I had the repair technician out and he told me that the control panel was bad and it would cost $300 for parts and labor to repair. We paid $600 for this dishwasher. Of course, we have the option of purchasing a new dishwasher and receive a rebate but that ends up being more than just ordering parts and replacing them ourselves, but something only 2 years old should not break. From reading all the other complaints on this forum, I am surprised that Maytag has not done something about the control panel and the humidity issue which seems to cause the control panel to go out. This is an expensive fix which Maytag needs to address. Come on Maytag!

I purchased the Maytag Bravos XL washing machine because I wanted a top loader that was water saving. This washer boasts of a 10 year commercial capacity so I thought I was buying a decent machine. Unfortunately I have had a very disappointing experience. From the start this machine has not cleaned clothes properly. We circle clothes around the agitator and only fill the machine a third of the way full. This is the only way to ensure clean clothes. We use HE soap.As if this hasn’t been bad enough, the entire motherboard seems to be glitching out. It throws a different code each load and sometimes won’t start. Other times it won’t stop. It isn’t safe to use when we aren’t home or are asleep, making the time delay feature useless. Last night the machine ran for 2.5 hrs on a 1hr 30 min estimated deep water wash. I finally turned off the power and let it drain out after it insisted it had 45 min for the last hour.... this thing is a total waste of money. Will never buy another Maytag!!!!

We bought what was supposed to be the top of the line Maytag dishwasher as part of a kitchen remodel in 2011. Well tonight it has quit working for the 3rd time! I think this is the last straw for us! Tired of spending all this money having it fixed. We also bought a Maytag microwave at the same time that has been nothing but trouble from day 1, but not as bad as the dishwasher. I can promise you we will never buy another Maytag product ever. Heck at this point, I would not accept a free Maytag machine of any kind! Stay away from Maytag!! Just to be more specific, the first time the dishwasher quit it was the board and cost us half as much as the dishwasher. I see lots of mentions of boards going out early.

I recently purchased a Maytag washer and dryer from Lowes. The performance of the washer was highly unsatisfactory. The water sensor does not allow sufficient water to enter the machine. Thinking it was a malfunctioning machine, I spoke to Lowes, and ask them to swap it out with another machine. They were cooperative and pleasant to deal with however, the replacement machine was no improvement. The water sensor does not allow enough water to enter the machine to even begin to saturate the load of laundry! I bought a washing machine, not a dry cleaning machine, but a dry machine was what I got and that is NOT okay with me. The literature states that load will not be covered with water, so that is how it is designed to work. With inferior water levels, and no agitator, there is not even a chance of water splash saturating and cleaning clothes. I am not an engineer, but common sense says this is efficient nonsense. VERY, VERY DISSATISFIED!

Love, love this washer. Does an amazing job cleaning colors, whites, and bulky bedding. If you like Tide Pods or other liquid pacs, this might not be the washer for you as they tend to end up inside the gasket. Powder-filled pacs are no problem however.

Model mdb7749sbm. Unit is just over 1 year old and fails in the same way everybody else in complaining about. Here is my question, this failure mode is obviously a designed in feature providing planned obsolescence to the device. Why is this company not being held to account for the damages in this case? Are all the judges that bought that no suit can be brought?Have all of you contacted your state consumer protection organizations regarding this issue? I would also recommend that you write both your state senator, the state consumer protection organization and any media outlets you can think of. High rate of control panel failure, devices activating by themselves when people are potentially away from the house, risk of fire or flooding... these are serious things and I would think a story that some news organization would surely be interested in digging into. Now that would serve to light a little fire under the Maytag organization if something like that was to occur.This sure seems to me to be a defrauding of the consumer - selling them a product at the top end of the price range that has such a significant design flaw that in the end can only be considered not fit for purpose. I havent yet contacted Maytag and Home Depot (who I believe are fully complicit in this as well), but I will be doing so to give them a chance to make this right, which I fully expect them to decline to do. Then I will begin writing letters. Am also considering small claims court. But above all, do not just accept this and move on! Companies like this need to be held to account, and they need to be reported so that others purchasing new devices in the future know to stay away from them.

The machine runs and runs and runs and still the clothes come out dirty. Clothes are often not even wet all over. The Maytag HE water-saving washer is a terrible Hoax. The dryer also is faulty. It rolls the clothes into a big, undried ball of dirty clothes.

Ive used Maytag Dishwashers since the 1980s, from Alabama to California. And I wouldnt change a thing. In fact my entire family (well the folks that can afford it) uses maytag dishwashers. Extremely satisfied we are.

I bought a Neptune Washer in 1999. 6 years later (2005), it started making the 747 landing noise. It was implied that somehow it was our fault, maybe, something from my contractor husbands pocket. After all, it was a Maytag, and surely there could be no design or engineering flaw! (My daughter still has 34-yr.old one.) We were told the repairs would be so expensive. It would be wiser to buy a new one. Foolish me, I bought another Neptune to match my dryer. Of course, now this one has the same bearing problem and again its cheaper to buy a new washer. I am angry and not sure how to proceed. Any washer, but especially a Maytag, should last more than 5 - 6 years. I should not have to buy my 3rd washer in 12 years. And if I do, it certainly wont be a Maytag!

Purchased an expensive brand new home which had Maytag appliances in it. After about 1 1/2 years the freezer bottom began to constantly freeze and drip onto my floor. I researched the issue and found it was common, simply thaw the area where it freezes. Did it multiple times, we do not overfill our freezer etc. We must take the ice out of the bottom every 4-5 days. My hardwood floors are destroyed now. We purchased a Samsung fridge freezer bottom when they first came out years ago, had it for 7 years, 0 issues, but it went with the house. Now my Maytag oven door is locked shut, also it takes a very long time to boil water. Maytag junk. I am going to buy another Samsung fridge tomorrow.

So our 4 year old Maytag Dishwasher just took a crap. Thank God we were at the kitchen table when it started to smoke, which smelt like burning wires and unplugged it immediately. Repairman came out and said it would be a 3 to 4 hundred dollar repair. What happened to the great 10 year Warranty? Oh yeah, its a limited warranty which does not include wiring. Could have burnt down my 4 year old home, but thats ok, not covered. The good news, the upper arm I replaced due to wear and tear would have been a free repair, because it would have been covered! No more Maytags in this home, ever!!

Bought this because it’s American made. It seems to be very glitchy. If you don’t use the detergent drawer it always flashes low detergent. The quick wash leaves soap on clothes. It acts up and leaves clothes too wet. No buzzer to tell you when it’s done. Have to hold button for 3 seconds to start. You can’t just hit button and walk away. Then wait for it to sense the load first to make sure it starts. Very expensive model.

Absolutely the worst washer we have ever had. Clothes come out smelling and look like they havent been washed. I should have bought a cheap washer, I bet my clothes would have been cleaner. The machine makes you think it is the best ever made by the looks and the price. Im sorry I ever wanted my money.

I bought a new Maytag Quiet Series 300 in 2005 and have had nothing but problems with it. The internal plastic pieces that hold dishes in place have broken off regularly. The door handle also broke. The dishwasher does not drain all the way every time. Now, the dishwasher will quit randomly before finishing its cycle. Our model (MDB7600 AWB) was not part of the recall, but is a lemon nonetheless. Of course, all of this occurred after our one year warranty had expired. This dishwasher is a lemon and a waste of $400. Well never buy another Maytag product.

I purchased a Maytag Bravo Washer in October of 2011, I had a repair man come to check it since the spin cycle sounds like a jet is revving its engines in the laundry room. He told me that the repair cost is $493.50 to replace the transmission. The machine also has problems with the circuit board. The lid lock goes on and off and on and off so you cannot run the machine. Speaking to Maytag they just kept saying your warranty is over and we dont offer any assistance on the repairs. The machine cost $530.00 in 2011 and they think its reasonable to have repairs more than the cost of a new washer. They said they had no complaints on the model. My repairman advised not to buy Bravo, Cabrio or Calypso models since they all have the same problem with the transmission and electronics. I think they should at least pay for the parts, the transmission is $300. And we didnt even price the electronic part of repair.

We bought a Maytag oven in Late October 2018. On January 22, 2019 the oven quit heating. Since it was still under warranty we called Maytag and they sent out a contracted service technician. The service tech said the circuit board had gone bad, and said it would be 5 to 10 days for part to come in. After a month the part still had not come and service tech was not returning calls. We called Maytag after another week and they provided very little help other than, We will contact service tech. Service tech never called us nor did Maytag call back. Called Maytag back on 3.10.2019 and asked how we could get this part and oven fixed. Customer service representative was not very helpful as they asked for part number which she was told was a circuit board and the tech they sent did not give that to us. After the customer service rep continued to provide any help other than say call service tech they sent out. I asked what if they replaced it for us since we have been without now for almost as long as we have owned. She stated Maytag does not do this except in extreme cases. I asked what is considered extreme cases. She stated she did not know. At this point I asked if she could transfer me to her supervisor and sat on hold for an hour, then had to leave for work. Very disappointed with Maytag and their lack of support to back their product.

Have read others reviews and experiences and wish I had visited here first. Our first Maytag washer and dryer set lasted over 25 years with only minor repairs until the transmission started to leak grease and was uneconomical to repair. Our second set only lasted nearly 10 years and were obviously lesser quality. The wife decided that she wanted the best and high tech version. She really liked the features of the Bravos 300. What a mistake! Not even three years old and she has been dealing with the noise and the problem with constant unbalanced loads, intermittent error codes, odors and the forever cleaning requirement. The whites were intermittently getting rust stains until I determined that the underneath side of the top cover around the bleach reservoir had rusted out big time. I replaced the top cover for over $125 plus an afternoon that I will never get back. (Out of warranty, of course). Today the wife called me to say that the washer would not complete the rinse cycle and she could not reset it. We had to pump out the water and pick the wet clothes out. A grinding sound is coming from near the bottom of the machine and sounds expensive. The service man is scheduled to be here day after tomorrow to give me the bad news. My next washer purchase will NOT be a Maytag or any other high tech piece of crap. Simple is better.......

We purchased a Maytag from Lowes about 3 years ago. The spin function quit working properly last Feb 19. We paid $350 to have parts replaced thinking it was a fluke and we would be set for a long time to come. Well, last week the same thing happened... not even a year later. Lowes doesnt care and Maytag doesnt care. They want you to spend more to get a warranty to get you to 5 years... well as far as I am concerned that is not good enough. An appliance should last 10-15 years. This Maytag was to replace a Whirlpool that caught all of our clothes in the agitator fins, so after a short period of dealing with that we paid out for a Maytag without an agitator. So in the span of 6 years... we had about $1,500 of dissatisfaction. I believe our repair guy said they the companies are one and the same. Selling junk ought to be illegal.

Why are the clothes in my dryer getting stuck in Maytag Neptune? It seems there is a little opening around the rim of the barrel in the back of my dryer that drawstrings, zippers or similar small parts of the clothes can get stuck in. It twists the clothes around and is ruining clothes, also is making a thump-thump sound. Someone, please help!

I bought a brand new top/bottom refrigerator from them. 1 1/2 yrs later, the cooling stopped and had 2 repair guys come out. They replaced it with BRAND NEW refrigerator. Now 1 1/2 yrs later, the same issue is happening. ALL my food I buy goes to waste. I bought NEW so this wouldnt happen. What happened to the old fridges from back in the day! Maytag has the WORST Customer Service!!!

One time at around yr 2 of our 10 yr warranty the repair guy removed my agitator, spline gone. Couldn’t find one anywhere! After a month of using a laundromat, I called the company in Montreal and they had the new agitator in my post office in 4 days. I am unable to wash anything that puts the Bravo washer out of balance ie: towels. The sides are busting out on the machine!! We have only had it 4 years so far. Not impressed! Does the warranty cover busting out sides? As it is a major part of the structure of the machine.

I got a new washer and dryer for my ex wife and son last August. Its October and the agitator broke off. She is not abusive to things and just the two of them dont produce much laundry. This was just poorly built. Maytag should be ashamed to have built such a poor product. I thought GE had the worst appliances, but Maytag must have hired their engineers. I have pictures and it has 10 year warranty right on the lid, lol. Should be 10 months,

I will never buy anything made by Maytag again. I just bought this washer 9 months ago and the sensor broke. The repairman said I have to pay $300 for the new part and it will take 3 weeks, then the repair told me many people have this same issue and he wanted to be honest that this always happens to these washers and my best bet is to buy new... I am so sad I saved for 4 months to buy a new washer and it was a bad decision. I have learned my lesson.

After the waranty ran out, oven failed to ignite. Called repairman who couldnt diagnose problem. Broiler works. Replaced some kind of wire & part for $350. Good for 6 months. Happening again. Paid a lot for this oven.

My dishes come out super clean and I love it, even when there is calcium build-up around the filter. Thanks to Maytag and their great technology. You cant beat Maytag.

Bought washer and dryer as a pair and Ive owned for 8 years with zero issues. Everything works as built and promised. Why would I expect anything less from a brand like Maytag?

Our refrigerator is just 2 years old and it have been leaking for over a year. It started leaking right when the warranty expired. I am so mad. I called them and they said... You can purchase a warranty for $400. I am like.... what!!! I called my home warranty and they fixed it for $100. A few months later it is leaking again! I am so mad... It is a $1200 refrigerator. What can we do as a group to fight for this? There have to be something that we can do?? It is so frustrating. If there is an attorney that can take care of this group that would be great.

I just finished paying off my Maytag Bravos series washer and dryer, and now they are failing! The washer isnt getting dirt out and the dryer power button broke. And its not like I can use some pliers to get the switch to work, its like the part that controls the power just dropped out of existence, leaving me with a knob in my hand that connects to nothing! Of course, the limited warranty only covers the drums, not the little dinky parts that break more easily. I had inherited a set of Maytags and they were well over 20 years old (possibly 30) and they both were powerhouses. But this is terrible! I feel super disappointed that Im going to have to buy a new set after only owning these for 18 months. I know I WONT be buying Maytag ever again, though!

I moved into my home in July 2013. My kitchen came with all stainless appliances that appeared and seemed to be in excellent shape. I have been using the Whirlpool Microwave oven to heat foods (all in microwave safe) containers and dishes. This morning, I was heating a muffin, when suddenly I hear popping. When I looked through the glass into the inside of the microwave I saw sparks then flames. I immediately stopped the microwave. The fire apparently started in the area of one clip that holds the metal rack inside. In researching this issue online, I found hundreds of complaints from people who have experienced the same issue, and Whirlpool refused to replace the unit because it is out of warranty.

I was in my bed and lights and TV flickered. Then, I heard a small explosion and my dogs went crazy. I went into the kitchen and my Maytag Gemini stove was smoking and smells really bad. I unplugged it. The sockets and the one close to it no longer work. My house stinks now. What happened? I have had this stove for a few years but it is not used often except during the holidays.

My Maytag Bravos washer is 6 years old. I had to have the motor replaced about 2 years ago. Now, it gets stuck on uL on every spin cycle. I had a technician come, and was told its just cheaper to replace the machine at this point. What happened to the Maytag man of old, the one who never has any work to do because the machines are built so well?!

We purchased a brand new Maytag washer dryer and had nothing but problems with both. After talking with corporate several times, trying to reach the CEO, the customer service person told us that the problems were buyers remorse. Needless to say we will never purchase another Maytag/Whirlpool product as long as we live. We are going with Electrolux!

3 year old Maytag Washer model MVWX600XW broke. Paid $345.55 for extended warranty. I had to wait 10 days for Appliances Unlimited to fix the washer in Sept. then the washer broke again in November needing 3 more parts including a motor. It took almost 2 weeks for Appliances Unlimited to come to the house, then I have to wait 5 weeks for a new motor to be in stock.

We bought a Maytag dishwasher March 2012 and the unit wouldnt turn on October 2013 - 6 months after the warranty ended. We called their service department and they told us to unplug the dishwasher or turn off the circuit breaker. We did so and the unit still would not turn on. We called a repairman who advised us that the touch pad was not working. The cost with parts and labor would be close to $300 which was more than half the original price. We repaired it and I sent all the papers with a letter to the consumer department and today I got a call advising us that they would not do anything. Do you think I have any further recourse? If not, I will never buy a Maytag product again and will advise anyone within a listening area as to how we were treated.

Purchased in 08 for a second home, we visit every other weekend mostly in summer. I have never been pleased with the set really. It takes too long to wash/dry, clothes get tangled, dryer goes off on first buzzer, wrinkled and now, the control panel has gone out on washer and they say it is approximately $500 to fix. I have probably used it 20 times a year. I have Maytag in Lex, which I have had for 15 years, that is 100% all the way around better.

I purchased a Maytag dishwasher on Oct. 12, 2013. The control panel failed in July 2013 and had to be replaced. I was unable to program a wash cycle and the lights would move all around the front. After the first failure, I was told that the control panel would only be covered for 3 months - the original purchase date for the washer, NOT the date of the NEW control panel. I was then talked into an extended service plan. Now, four months later, the control panel has failed again and I am unable to program a normal wash. A repair man is not scheduled to come for another 9 days. As a single homeowner, this product is not used even on a daily basis. I will never purchase another Maytag washer. They do not back their product with appropriate repairs.

Maytag BRAVOS XL Washer - The worst washer I have ever used. Do not buy! It does not use enough water and leaves a white scummy residue on dark clothes. You have to wash them all off in warm water and then send it through one or two more rinses to get it washed off. I may as well do laundry by hand! Absolutely disgusting!

Ive had the dishwasher model MDBH979SAB0 for about 3 years now. A few months ago I noticed the faceplate would pop out when you opened the dishwasher. I would have to pop it back in. The dishwasher was out of warranty so I decided to attempt to fix it. I took the faceplate off to realize all of the plastic tabs that screws go in to were snapped off. The only fix for this is a complete new panel from Whirlpool Parts Online to the tune of $194.17 (W10811169).The wheels also fall off the bottom rack. The push pin plastic becomes brittle over time and does not stay in the assembly. To replace the wheel assembly (there are 4 in total) is $38.18 each (W10195416V). The wheels or push pins cant be purchased separately. Both of these items are not covered under warranty past 1 year. Maytags 10 year warranty only covers the upper and Lower Racks (excludes cup shelf and silverware basket), chopper blade and stainless steel tub and inner door liner. So only a small percentage of the parts.The design of the faceplate is defective in that too much force is applied to the faceplate when opening the unit. The handle is integrated in to the faceplate. The plastic used becomes brittle over time and breaks. The panel unit (W10811169) must be replaced in entirety rather than just its housing increasing the cost of repair. To have this failure occur within the first 3 years of use is very premature. I can only assume if I repair the dishwasher I will have the same problem again. I am considering buying a new model that is designed better and comes with a longer warranty on such parts.