Product number MMV4205DS. Beautiful, felt solid. Right away when we would put in a time to cook and hit start, the thing would say Open Close Door. First we thought it was moisture, and we would wipe the seal, then lifting the door a little helped. A month might go by and we would repeat this process. I did a little research and found the microwave is known for this. After the warranty was up, it got worse. My husband put a little screwdriver in the door clamp. The plastic guard that held the door shut fell behind the opening. Mulling over whether to call for repairs or buy a new one, we decided the latter. I am buying another one just like it, because the holes in the wall will match for an easy swap and it matches my suite. This time I took out the 3 year warranty, which I will hold Maytag responsible for any more problems. They say if they come and fix it 4 times in a year they will declare it a lemon and replace. I figure this will work in my favor because the microwave lasts a year!

Sometimes the control panel is difficult to work with especially if the wash is paused to add more clothes or detergent. The good things is that the tub is very large so a comforter can be washed and you can control the amount of water depending on the amount of what is being washed. I also like that it doesnt have the big agitator in the middle.

I bought the washer dryer combo. Dryer already broken. Washer is very loud when it changes gears. Would not recommend the washer or dryer.

You cannot go wrong with Maytag, even if there were issues they are reliable in repair, and parts are available so you arent forced to purchase new like some technology. I have been pleased with the front load washer dryer since 1998.

It seems to be a broken record with other reviews. I had a 2 year old microwave and the door doesnt recognize that its closed. Which means it wont turn on when I close the door. So you have to open and close it maybe 30-50 times and sometimes it works. I call Maytag who schedules a company but doesnt disclose anything about the warranty or service cost. I was thinking it would be a nominal fee since it falls under a 10 year warranty. The company calls and confirms the cost and I recheck with Maytag who said that the warranty only covers parts. So I buy a $300 microwave and have to pay $160 for a service visit because your company made inferior parts. Absolute sham of a company. Buyer Beware...

We purchased the Bravos XL washer just over a year ago. It is being replaced 1/10/2017. Simply put this is the worst product I think I have ever encountered. Extremely noisy wash cycles leave residue on the clothes, clothes do not get wet in some spots. This washer is so noisy you can hear it from outside. What an embarrassment. You have to run the clothes twice first with detergent and again without detergent to remove the residue left over from the first wash cycle (not energy efficient at all). If I could give a minus score like minus 10 I would.

A little over two years and my Maytag dishwasher needs 300 to $450 in repair for circuit board or boards. The repairman said that they got cheap and left out a seal which allows moisture to get into the electronics, duh. They have a known problem but will not stand behind their screw-ups. Never again will I purchase Maytag, Whirlpool or any other product made by the bumbs.

My fiance bought this dishwasher 5 years ago but has never been able to use it due to the fact he is disabled and unable to open the door. When I moved in 4 months ago, I began using it regularly 2-3 times a week. Yesterday, I loaded it and when I hit the start button, it did nothing. The lights come on but the start button doesnt seem to be working. I have torn it apart twice and after looking all over the internet have determined that the control panel is bad. We live on a very fixed income and fixing something like this will take a large part of our budget. I am shocked that something so expensive can only last a few months then stop with no warning. We will be calling and adding our names to the list for the class action lawsuit here in California.

This appears to be a common, known, well publicized problem - freezer drain clogs and needs to be either changed or repaired with a fix, a free replacement part for the drain seal. Easy to install, takes 15 minutes. HOWEVER Maytag will not give you the part!! In order to take advantage of Maytags correction for a well known, chronic, manufacturer defect, you must engage an authorized service person for hundreds of dollars and wasted vacation time waiting at home for them to show up. Unlike any other product, recall this one is not free. My kitchen is full of Maytag products; dishwasher (not so good), range and a refrigerator that had to be replace when the compressor went out after six years. However this is the last straw, Ive learned my lesson, seen the light, THIS IS THE LAST MAYTAG PRODUCT I WILL EVER BUY.

We are having the same problems with the drain clogging and bottom of the freezer filling with ice and then water all over the floor. We currently de-ice the freezer once a week. After paying top dollar for what is advertised as a top product, we expect better service. Especially when Maytag is fully aware of this problem. We sent an email of complaint to Maytag. Heard from them today. They would pay for the replacement part but not the labor. Most places around here charge $250.00 just to walk in the door!!! Is Maytag kidding?!?! NEVER AGAIN. Will also tell anyone who will listen to stay away from Maytag. No wonder they dont belong to the Consumer Resources group!!

Purchased a Maytag fridge in August of 2010. Had issues January 2014 - needed a new circuit board. At the happy cost $230.00. Well it is now May 2014 and had to have the repair man here again for another circuit board $258.64. Maytag will not stand behind their product or parts they use in their products. They flat out told us that we shouldnt have to replace the circuit board that often and then said they wont stand behind it. So buyer beware. DO NOT BUY ANYTHING MAYTAG!!!!!

The machine dries out the clothes so tight that they are full of wrinkles. I am so dissatisfied with this machine, I spent almost $600.00 for this and this is what I get. I also end up with fabric softener all over the clothes. I use the Downy Ball and I just took out my black pants to find blue all over them. I contacted Home Depot where I purchased the machine. They said to get a hold of you. All I want is get a different machine, not an HE. This is beyond anything. Someone should have to put up with, can you help me?

In 2011 we purchased a complete appliance grouping at Home Depot by Maytag to include the dishwasher. For some reason we neglected to purchase an extended warranty on the dishwasher. Lo and behold in 2013 our control panel went bad and the cost to repair it was almost as much as purchasing a new dishwasher. Thinking this was a fluke we were dumb enough to purchase another Maytag from Home Depot due to the loyalty made in the USA. Well here we are 2015 not even a full two years later the control panel started acting funny a few days ago and yesterday just plain old QUIT. Fortunately we were wise enough to purchase an extended warranty plan on this dishwasher so tomorrow we will be calling the repairman. Unfortunately Maytag has never solved the problem that has been occurring for at least 5 years and continues to sell this product to unsuspecting schmucks like us who try to be true to the made in the USA slogan. Shame on Maytag!!! Our model number is MDB7749SBM. Buyers beware.

My experience is very similar to Richards below. I have an MDBH979AWS3 that was purchased new in April of 2010. Just over one month after my warranty expired, the touch panel ceased to work. Since it was no longer in warranty, I had to replace it out of pocket. The wiring harness to the old panel looked heat damaged. Last winter, the central computer died. The machine was useless. I called Maytag customer service and actually seemed to find a sympathetic ear. They agreed to a new part if I paid $129 for one of the two companies doing certified repair to install it. During the summer, it blew several fuses. Then in late November of this year, the touch panel went again. I hesitated on how to respond and waited until after the holidays to call them. I got the most rude customer service rep that Ive dealt with in a long time. Somehow, I was blamed for a misdiagnosis on the computer panel (duh, no, that was a different issue and it was indeed broken), accused of misuse of the dishwasher, and flatly told that they werent going to do anything more on a machine. So far, out of warranty. Im sorry, but I cant accept that a machine under 3 years old should have 3 major failures. Maytag has to step up and at least look at this problem. From what Ive read, this is a common problem that has resulted in several fires. Maytag has to know about this and continues to do nothing, not even issue a recall on the current touch panel used. I am now faced with putting another $100 in (which puts me at about $350 total on a machine I paid almost $500 for) or just buy a new product. Rest assured I will never buy another Maytag-Whirlpool appliance.

Im totally done with the Maytag brand that Ive trusted for over 30 years. I never knew until yesterday via Facebook friends that they are not true Maytag-made anymore. They were bought out by Whirlpool eight years ago. I bought my top-load Maytag Bravo 400 Series Washer ($1,028) at Home Depot in October 2008. No problems with it until now, less than 4 years old with error code DL. So I looked in the book and found it was the lid lock (the little red light wasnt lighting up when closing the lid, which prevents it from running).I made an online appointment with Sears Home Appliance repair to check it out. But after talking with online friends and googling fix videos, I was able to get it running today by taking the top off, unplugging the lid wire and plugging it back in. So far, its working but now I will fear each time I go to use it that something else will fail. My old Maytags (washer and dryer) bought in the 80s never needed service until they approached the 14- to 15-year mark. That only tells me that the newer made appliances are total junk! So many complaints and how the companies dont back their appliances, it just sickens me.

I purchased the Maytag Bravo Series in August 2010. Two weeks ago, I had to replace the idler pulley on the dryer which was no easy task. Now today I was washing a load of clothes only to walk into my utility room and find it flooded. This didnt even start out as a small leak so at least you would have a warning. On the spin cycle, the washer is making a clanging sound. These were not cheap models. I paid $1600 for the set. I will never buy another Maytag product especially after reading all the complaints that people have had about this series. Why hasnt something been done to protect the consumer? I did not purchase the extended warranty as I thought Maytag sold a good product. I owned another set of Maytags that were almost 30 years old when we got rid of them and did minimal repairs over the years. We are only a household of 3. It is not like these appliances are overloaded or abused. Its very disheartening. In this economy, most dont have money to just throw away and that is what I feel like I did!

Just when you think that youre able to do laundry. First, comes the musty smell. So, you clean cycle your HE machine using only the cleaning product directed by the manufacturer. Then, comes the pump being stuck on. Like it still have to drain yet your clothes are soaked but you heard full force of a good drain. Poof. Unplug and kick it. Look on YouTube and discover you should take it apart and clean out some obscure puddle holder & look! You discovered where the sock monster lives...its gross. Going to start my own business (125.00) to clean these things out. Hopefully not get some kind of fungus from the grossest mold ever. Its Maytag not a Home Depot issue.

Our Maytag Atlantis dryer had smoke coming out and almost had our house on fire! Had it not for us double checking the entire house would have burnt down! The dryer is less than 10 years old and already it is tearing apart. I cant risk using it again. Terrible company. I would never buy Maytag products ever again!

I bought a Maytag washer and dryer, the Neptune series and thought I was getting a top of the line, but now the dryer has quit working and the repairman said it is not worth fixing and it is only about 5 years old. So that is what I am so angry about.

We purchased a brand new Maytag washer dryer and had nothing but problems with both. After talking with corporate several times, trying to reach the CEO, the customer service person told us that the problems were buyers remorse. Needless to say we will never purchase another Maytag/Whirlpool product as long as we live. We are going with Electrolux!

I do not like this Maytag Centennial Washer at all, I have had it for a year and a half and it just does not perform good at all. Most of the time the clothes still come out with dirt on them but what I am most mad about is the fact that it keeps leaving bleach spots on my clothes, several washes after I use the bleach. I will definitely not recommend this washer to anyone.

This is the 3rd time my Maytag refrigerator has gone out on me and its only 7 years old! Its always the same thing, my refrigerator side starts getting warmer and warmer while the freezer starts forming crystallized ice. Both times its broken down in the past it has been the defrost timer. One service man said Maytag is not the reliable company it used to be and I would be better off buying a brand from Sears (Whirlpool or Kenmore) cant remember. Anyway, each of those services was close to $300 and now Im faced with another service call. We paid $2,800 for a refrigerator we thought would last decades. Well never buy Maytag again! I wish Maytag would own up to its cheap parts and send replacements to its customers with instructions on how to install!

Maytag Dishwasher Model # MDB7749SBM1. What a piece of JUNK! Purchased in June 2013. Control panel went out six months later! June 2014 Control panel BAD again (#2). March 2015 another Control panel replaced (#3). Thank God for Home Depots extended warranty! October 2019.... Control panel needs replacing!

Seems a little ** one of a small child crawled into the washer and a sibling turned it on. We have been married 35 years and seen a lot of washers and this is by far the worst wash machine Ive ever seen. How would you rather do my wash in an old fashioned mangler? Very unsatisfied customer.

Our product was purchased with our Condo. We have had it for 6 months & the first time I called someone was for the oven door being so terribly hot. I was told that was normal. Then I tried the cleaning of it & you would never know anything had been done. It would take a heck of a lot of elbow grease to get the marks off & I dont have the strength or time to be doing that. I had someone come again & he said to do it again, which I did & it still was not clean. I have done it a 3rd time now & still no better. I think this product is a total piece of junk & would not recommend it to anyone. I am a very unhappy customer & will never purchase another MAYTAG product.

We bought a Maytag dishwasher (Model: MDBH979AWS3) in January 2010. In April 2012, the control panel stopped working. A local repairman came out to see it for $160, diagnosed it, and suggested that we call Maytag to see if they would give us the part because it was only a two-year old machine. He did say that the control panel was not a part that was troublesome!Maytag offered an extended warranty for only $287 that would cover the part! The total repair cost was almost equal to the cost of a new machine. Home Depot, when consulted, acted as if they know nothing. After reading about other peoples experiences with this company, I feel that it is no longer an honorable company standing behind its products. In fact, the whole repair process is set up to rip off the consumer.We will now look to purchase the best and cheapest non-Maytag product, not from Home Depot, and throw it away when it gives out, which more than likely will be soon. These companies have finally convinced me to do what I am sure what they have always wanted every consumer to do. Throw it away when it breaks down.

The Maytag MFI2568AES refrigerators ice maker is broken and we cannot get a replacement unit. Whirlpool who now owns Maytag is of no assistance. The unit is two years old. I understand planned obsolescence but this is ridiculous.

After 2 years the oven didnt work. I had a repair fix it for $500 but if I wanted the convection to work it would cost another $800. Obviously not worth it. Now the oven needs to be set at 400 if I want then actual temperature to be 350. Now the latest - the racks are too small and falling! I just put my Le Creuset in the oven and the rack fell. Splashed everywhere! This happened at Christmas with my turkey. So bought the fridge - everything in the back freezes. Never ever buying Maytag again. Im guessing the Maytag repairman isnt lonely anymore.

Same problem as all the others, the dishwasher stopped working. The dishwasher is less than three years old; for a two-adult household. The control panel just stopped getting power. After multiple calls to Whirlpool/Maytag, all they will do for me is document my complaint. Im now out $167 to get this thing running with no guarantee that it wont happen again, as well as the fact that this should not have happened in the first place. I didnt misuse my dishwasher. It just stopped! I think there needs to be a class action lawsuit since the manufacturer will not stand behind this obvious defect.

For families where people work in gardens, work on vehicles and get just plain dirty doing things anywhere outdoors these agitator-less machines are not for you or me. Ive had mine for two years and I truly dislike it (Model MVWC425BW1). With different products I scrub dirt and grease stains on pants before they are put into the washer, scrub again when they come out of the wash and then scrub and wash again a few more times but I cannot get all the dirt out. I now work more on laundry and harder since I got this machine.This agitator-less machine is designed for people who dont get really dirty - just remove everyday perspiration and household grime. I think this machine was designed by engineers who have never done daily laundry for any length of time and theoretically thought it would clean really dirty clothes. They were really wrong! Having done laundry for 50 years, I now know that an agitator cleans better. It would be nice if other women and I, who have done laundry for years, could be on focus groups about developing new washing machines.

I bought a Maytag Bravo without an agitator. Regretted from the 1st load. Some of my clothes do not even get wet and I bought the commercial grade. My 20 year washer that was on its last leg washes better than my brand new Maytag. Please do not waste your money, your clothes will not come out clean.

Bought brand new Maytag dishwasher. Worked great for 3 years. Then caught on fire. Couldnt contact maytag for a month because when you call your on hold for 30 minutes. Then when I do contact them they will only want to give 50%off another of their products that Ive already had catch on fire. I will never buy another one ever.

We have been married 50 yrs. We have never had a Maytag, we bought one 4 days ago, Dec.13, 2017. This is the worst wash machine (Maytag Bravos XL MCT) we have ever had, the clothes come out wet with white soap marks on the dark clothes. Lowes said we can exchange it for another washer, it will not be a Maytag.

If I want to line dry something, first I have to pick off all the lint. Even when I use the dryer, I still have to pick off lint and there’s often creases with dirt dried right in. I have to inspect everything that comes out of the washer to see if it is clean before I dry it. This doesn’t save water, as I often have to wash things at least twice. Awful! Also, ridiculous. A wash machine is supposed to get things clean.

I bought a Maytag front loader washer and dryer, plus the pedestals for each. In last August of this year the washer just stopped in the middle of a wash cycle. I placed a call to the customer service. The tech diagnosed and placed an order for a part and set an appointment for two weeks later, with a time window 1 to 5 pm. The person called at 5:30 to tell me he had an job before he could get to me. I had taken the day off to wait for him. I called and they ended up rescheduling, for two more weeks.. Tech came ordered different parts, tech did not show up. Tech came out again ordered new parts. Next week he arrived wrong parts. Washer still not extracting. New tech, new parts, new appointment, this was what happened throughout September and October. Tech was not happy with his job, stated that to me, would not do anything but install part, even if it didnt work. He took parts with him. The washer still not extracting. Last Thursday he didnt even have all the parts, made the decision to replace machine without discussing it with me. Told me Sears would call me in 48 hours. Received call today Tuesday. Go to Sears to have it replaced. None of the machines they offered are compatible with mine. I will have to purchase the pedestal for the new machine, plus pay the overage to get the comparable machine. Service appointment people were horrible, cold and rude. Sear store at the mall where I purchased my washer said that it was not their problem. Once we sell it you are in their hands. Have had Maytag for over 30 years. Will never buy it again. Will never buy at Sears again. Too bad I have to replace my washer with something from Sears. Not enough space to write everything I have gone through, the lost workdays, the extra expense of having to go to the laundromat, the stress of dealing with incompetent people and techs.

Maytag Dishwasher purchased for $634 on 7-6-12 from Lowes. Control panel malfunctioned in August 2014. Started leaking in April 2012. From the online comments, I am trashing this machine. It is not worth fixing it and having it malfunction again. Maytag will not say anything about this, only offers a repair person out to fix. I am very disappointed that my hard earned money purchased a sub standard machine. Maytag used to mean reliability. NO more.

Purchased 6-1/2 years ago when we had kitchen remodeled. Bought the stainless steel with stainless interior. The interior design was perfect for placing the various dishes, glassware and utensils. There are a number of settings to choose from, however, we tend to use it as more of a sanitizer so the light or normal wash are the preferred and dont use the heat-dry as we dont find it necessary. Very pleased with the quietness of the cycles and have no regrets with our purchase.

Oven failed after 2.5 years of normal use (1-2x / week). Apparently a relay failed (and burned out bake element). Contacted service & parts dept and learned that repair would cost $100 for service visit and $413 to replace the control board. Only the $80 bake element is covered by the limited warranty. Wonderful oven if your hobby is appliance repair. After 2.5 years, it now functions better as a toilet than an oven.

Ten years ago I bought a very expensive set of Maytag Neptune Washer MAH5500BWW and dryer units with the single all-in-one pedestal. The washer starts sounding like a freight train during the fast spin dry cycle. A service tech came out, turned it on, listened, told me it is bad outer tub bearings going bad. And the price to fix is $846. Its essentially a throw-it-away deal. The tech says he has done hundreds of these and its a 3-hour major tear down, the bearings are press fitted and you essentially buy a new outer tub instead of replacing the bearings in the old one. Maytag went out of business and was bought by Whirlpool. What a piece of crap and to think how great Maytag once was. Now I have a dryer and a pedestal that probably wont fit any other washer brand.

We received our new Maytag French door refrigerator today via delivery and got everything set up and magnets stick to the front. The last I checked magnets should not stick to stainless steel. So I called the Menards where we purchased the refrigerator almost 2 1/2 weeks ago and the store manager said there was metal liner under the stainless steel and states this on the technical specifications. And everywhere I went to look under the technical specifications NOWHERE does it state there is a metal liner underneath and even if there was the top is stainless steel regardless so why would magnets stick to it. I paid for a Maytag and basically got a cheap piece of crap Frigidaire or Whirlpool and paid extra for Maytag to stick a Maytag label on it. What a joke. If I have any other problems I will personally deliver this refrigerator to Maytag/whirlpool corporate and put it on the front step. I am VERY ANGRY!!

Bought DW 2 1/2 years ago. The control panel has a mind of its own, and today it will not even light up. How does a recall happen? I see lots of people having trouble with this model and others as well. A dishwasher should last much longer! Will never buy a Maytag again... and will recommend the same to my friends.

Bought the xl about 14 months ago. NO LIE! Exactly 2 days after the 1-year warranty was up, the xl went down. Drive shaft and bearings. Did Maytag honor the warranty since it was only 48 hours past the expiration? Not just a no but a why are you bothering attitude. My brother and I are above average machine builders. Well fix it ourselves because we could buy a new one to have it repaired. After many hours scouring the web we found the parts. Maytag didnt make a repair kit available to the public. 7 hours plus over $200 to tear it down and to clean the muck trapped at the drain. Then sand-smooth the burnt on metal where the bearings sit. All for a washing machine that sucks at washing clothes in the first place. Never ever again will I buy a Maytag.

To begin with, the Bravos 300 washer was bought because we owned a Maytag previously and it was with us for 25 years. It was still running when we gave it away and the only problem was a small oil leak starting at the drive. The new washer has no agitator, just the new style flat thing at the bottom of the tub. You cannot wash a set of fitted sheets without it turning into a tangled mess. The washer quit working after about 5 years and all indications pointed to the control. The control would reset after unplugging, but would freeze immediately when you tried to enter a command. We live in an isolated place and it is not feasible to fly in a service person. I ordered a new control, but there was no change in function. After several hours of detective work, it turns out that the mickey mouse plug for the electrical connection at the pump had broken inside. Because the pump would not work, the whole control would freeze. We will never buy another Maytag.

I had a warranty that I bought over a year ago. The dishwasher since then has been a monster beyond control. I called Maytag and the woman asked how long it has been acting up. I said about a year, but I was not sure. They refused to honor my warranty because they said it would only go into effect 60 days after I purchased it. They are translating about a year as an absolute and refused to honor the warranty. I would never ever buy a Maytag product again. Never. I will contact every person I know not to buy such a faulty product.

I spent extra money on a commercial grade Maytag dryer $1300 before taxes because it had a 10 year warranty. The motor and drum quit - and Maytag refuses to honour the warranty. I am appalled by their dishonesty and lack of integrity. I do not recommend them to anyone.

Just bought a Maytag Bravos 4.3 cu ft washing machine from NFM. The first machine delivered was broken it didnt wash or spin the clothes. NFM sent out another one at 9:30pm. It doesnt spin the clothes out well & loads have to be small. Poorly made.

Ive had my washer for about two years and have been disappointed from the get-go. I did a lot of research and found this to be top rated... Wrong! Even though I use the HE detergent and Ive even cut down the amount with no results, it leaves gobs of soap/lint residue on most of my darks and I wind up having to either rewash on clear or rinse by hand to get rid of the stuff.Ive also noticed some snagging on some brand new towels, but I attributed that to possibly the brand. Well, then I had an issue with some very expensive bottom sheets shredding and raveling and still didnt catch on. Today I noticed a different towel with similar problems, which led me here and walah! I see Im not the only one having these issues… Darn! Warranty is expired and Im stuck!

I purchased this washer approx. 2 years ago. It will not spin. Called 3 repair men, only one would look at it. The cost to repair is more buying a new one. I am buying another washer and it will not be a Maytag. Seems from other post live on this washer is 2 years. My son has one just like it, told him of the problems. He is thinking of selling and getting another one before his quits. There are 5 in his family.

I purchased the Bravos XL washer and dryer combo 2 years ago. Dryer is fine, but washer was EXTREMELY noisy from day 1 and has gone downhill since. It would leak during spin cycle and frequently stop due to unbalanced load, refill and stop again. Now it wont spin at all! We have checked to make sure it is level, it is. I live in a very rural area and its very difficult to get repairmen to come out. This is my first and last Maytag for me.

I bought the model 2 weeks ago and the lock is already going out and it wont wash my clothes. I thought they were high quality but I guess I was wrong.

I sold my 20 year old Maytag set and upgraded to this Maytag Bravos washer. This machine takes almost 1 hour to do a load and they come out dirty. Only way to get clean is to set on bulky sheet which uses twice as much water as old machine. This unit should have never been put on the market.

Back in late 2017 we paid over $800 to purchase a front loader Maytag washing machine from Lowes. Before the year long warranty was up, the control board/motherboard stopped functioning. Maytag sent a repairman who tried to blame the problem on us even though he appeared well aware of the problems with Maytag/Whirlpool. After appealing to Lowes, they intervened and Maytag agreed to replace the washer with a higher model. (This process took many phone calls and a great deal of frustration).One year later, shortly after the warranty expired on the second washer, the control board again stopped functioning properly on the second Maytag washer. Since then, I have been rebooting the machine, starting the cycle over again numerous times and doing everything within my power to keep the washer going. The cost of replacing the control board is outrageous. Soon I will replace this machine with an LG with an extended service warranty. No more Maytag or Whirlpool products for me! They are once great American corporations that have fallen apart and are riddled with dishonesty and greed. I guess these corporations only mirror what is going on in this country and government.

This product was purchased in March. In September, the agitator broke off. Thats a new one on me with a washer. Every other one Ive bought tended to last 10 years or so, then something like a motor wore out. It was an obvious design flaw on a topheavy agitator held on by a flimsy plastic sleeve. To make matters worse, their warranty service seems mostly geared to selling extended warranties, necessitated by the poor quality and bad design of their products. So, for a mere $182, I can have it covered for the next six or seven times the agitator breaks. No thanks, Ill figure out how to fix it myself when its no longer under warranty, or just cut my losses by buying another machine, and never another Maytag or Whirlpool product. I had a similar experience with a Whirlpool refrigerator purchased in April 2017, which had a defective module that went fortunately just before it was out of warranty.

I had a Maytag washer and dryer for over 25 years. I loved them so I replaced them with the Maytag name. They are not the same company as far as pride and product workmanship.From the get go it always had a dirty odor to the tub, as though the clothes had been left in it for days. I was told to just run through a cycle with bleach, but nothing. There is no lint collector and after about 8 years of using this washer, the old lint is in the bottom of my washer after every wash. Now, I have to deal with the thing coming to a screeching stop, not spinning out the water after the wash cycle. Sometimes it’s full of water and other times some water drained, but the clothes are full of water and not spun out.Now tonight, I went downstairs and found water on the floor, it’s leaking. My question is to call and get it repaired or not waste my money and go buy another brand. I may go with the latter.I purchased a fridge and dryer at Home Depot a few years ago. I wanted to stay away from Maytag name. I purchased another name only to find out it is part of Maytag. No wonder I’m having trouble with my fridge, making ghost-like howling sounds so loud it consumes the entire house. So annoying. Stay away from Maytag. They are not the same reliable, take-pride-in-work company.

We purchased our washer and dryer set in December of 2010 and had it for about 2 years with the extended warranty...needless to say around 1 1/2 - 2 years the metal around our bleach dispenser started rusting. Maytag considers this cosmetic! I am shocked to think that its cosmetic...on the outside of the washer yes, but on the inside no! It is faulty on Maytags part. I have spoken with Maytag and they tell me if it doesnt happen within the first 30 days there is nothing they can do. So I will tell anyone and everyone what was said to me via Maytags own repairman, Buy cheaper washers as NO ONE offers an extended warranty on the inside of the washer rusting. Whirlpool is the owner of Maytag now so beware of Whirlpool as well. Check out the warranties and make sure you will be covered longer than 30 days for rusting on any washer you intend on purchasing. We learned the hard way and well....we will be buying a cheap washer like the repairman suggested when this one goes out.

I purchased a white Maytag gas stove over 12 years ago. It has been great and never caused any problems. I live alone and rarely use the oven. However, I use the stovetop daily for cooking. With continual use, it has a lot of nicks and scratches. It also has stains inside the glass oven panel that I cant clean. The glass would have to be removed in order to clean inside. This is why I give a rating of 4 stars. If I used the oven more frequently, I would notice if it had any problems with the temperature, proper cooking, etc. and could give a more accurate rating. I have small toaster oven and therefore, I cook practically all of my meals in the toaster oven.

We bought all Maytag appliances two years ago when we redid our kitchen. I have had nothing but a nightmare with my Maytag dishwasher. It started to leak so we called in the service repair person. He said he could not find the leak but tightened something in the washer, it still leaked. We had him come in again because it still leaked and nothing. We called in a plumber to see if he could find the problem. He couldn’t find anything wrong with the plumbing and thought it might be the washer door seal. The washer is still leaking, it will be the third time the repair man is coming to fix the washer. At this point, I just want to get rid of my two year old dishwasher. I will Never buy another Maytag product. This ordeal has been a nightmare with no help from Maytag service centre. So, so, disappointing.

I just saw that there had been a class action lawsuit settled in 2005 for the Maytag Neptune front load washer and I was never notified as an owner! I have this crummy product and have been living with it for more than 10 years! I just scheduled a repairman to replace the moldy gasket (for the second time) and the noisy pump, and a latch that has to be slammed for a sum of $438. What a crock. I was told this was a top of the line model when I purchased it for $999. Ive never had such a piece of junk before in my life. I run loads of bleach weekly to control the mildew.

Purchased model MBF1958XEB4 September 2012. The unit is provided with a bottom freezer. About 2 month age water was forming and freezing on the bottom of the freezer compartment and leaking on the floor. It appears that this is a common design flaw recognized by Maytag with an updated part available that is intended to correct this problem.Contacting the extended warranty company I was informed that this is normal maintenance and not covered under the plan. Liars!! One does not remove a car engine to change the oil. To correct this problem the refrigerator is required to be pulled from the wall, disconnected from power, remove the back lower cover, disconnect two wire cables, replace the drain tube and reverse the process. Normal maintenance - give me a break. The company promoting this phony plan is Federal Warranty Service Corporation in Atlanta, GA. Do not buy a plan from them and if you have one cancel and receive a refund if possible. Maytag get into another business because your product is junk.

I bought a Maytag Dishwasher Model #MDB7749SBW2 in 2013. It worked great for 2 years. In 2015, the control panel malfunctioned. All the lights on the control panel would light up and the dishwasher wouldnt start. I called Maytag. They sent out a service tech. He replaced the control panel. I started having the same problems two years later, 2017. I called Maytag today, 9/11/17, to see if they had recalled this dishwasher. No, it hasnt been recalled. They offered to sell me a extended warranty for $400+, that would pay for the service call and parts or, I could find another Maytag, Whirlpool or KitchenAid dishwasher and depending on the model, I could get a 25-45% discount on a new one. I asked why they havent recalled this model, due to the problems that so many people are having. They dont know. Im writing this review to let those of you who have bought this dishwasher know, that the product is faulty.

Recently May 2019, bought a Maytag Bravos Washer, HE. Its now installed and so disappointed with this product. Not enough water to wash Clothes. Would of taken cashback from Maytag, but cant wait 6 to 8 weeks for cashback. 6 to 8 weeks after they have washer picked up. How long did we want to go without clean clothes, hummm. Problem was looked at by a professional appliance repair company sent by Maytag. His opinion, suggestion was, washer just didnt deliver enough water to wash clothes. I know its HE, suppose to me water miser, but Maytag Bravos just doesnt give enough WATER. How do we get clean cloth like that. As I mentioned in summary, I have added attachment close proximity to add water to washer raising water level to wash Cloth. Yes with proper water it does clean good, JUST NOT A AUTOMATIC WASHER now. Were only two, Rural NB, up to 3-4 washes per week, more when company around.

I own a Maytag dishwasher model number MDB7749cBM 2. The panel on the dishwasher stopped working. It is only a year old. Its too new to break down. Will contact Maytag today. There are so many complaints. Why not a recall?

The Maytag MGR5875QDW oven does not come up to temperature. It might start, but then it will give 2 dings and show a failure. I have called the 800 number in the manual. There’s no good help. I turned the power off and then on. It’s no help. This a pain in the rear end. That is a kind way of saying it. Home phone is **; cell phone number is **. Call me any time. Thank you. You do not want my wife to go on the internet!

Purchased a Maytag Bravos 300 quiet series and am totally dissatisfied. I have a bandsaw, router and several saws in my workshop and by far my Maytag washer can drown them all out with the noise it makes. On top of all this it does not complete its cycles before it shuts off and if you try to restart it you never know where in the cycle it is going to start at. This may occur six or seven times before you are able to complete one wash. It may take a day to wash one load of clothes. Maytag should refund the total purchase price of this piece of junk!

I waited my entire life to age 47 to purchase a brand new matching Maytag washer and dryer. I was thrilled. That was August of 2012. 3 years and two months later, the $800 dryer (MEDE201YW) loses the entire control panel and Maytag refuses to offer any assistance. I deliberately purchase Maytag with its stellar reputation, an American based company only to be more disappointed in the product and the company than in any other appliance Ive ever purchased.

We purchased our Maytag Refrigerator brand new, about 18 months ago. It always ran loud so the repairman came out during the 12 month warranty period. He told us to unplug and reset it, but that never did the trick. Eight months later, the fridge stopped cooling. We called our local repairman and he told us ($97 later) that the compressor was out. He said we should contact Maytag because the compressor should be under a 5-year warranty. Then the nightmare began. I spoke to four different reps with a total hold time of about 2 hours. Two of the reps put me on hold to get a supervisor and/or consult another rep and I was mysteriously cut off each time. One rep told me my compressor wasnt covered under warranty. The last rep I spoke to told me it was covered and he scheduled a Maytag repairman to come and replace the compressor. I was thrilled. The repairman came out and informed me that the compressor was indeed out and handed me a bill for $137. I asked why I was being billed and he said because that was the way that Maytag had ordered the service call. I told him that the Maytag rep had assured me that Maytag was covering the repair. He apologized and said that not only was I obliged to pay for the diagnosis (which I didnt need because I had already paid my local guy for the same information), but that it would cost $900 to replace the compressor. I was flabbergasted. I called Maytag and they denied all responsibility. They said that even though the rep had assured me of Maytags commitment to replace the compressor under the 5-year warranty, he had made a mistake and I wasnt actually covered. So I paid our local repairman to replace the compressor, because by that time, we had been living out of ice chests for 2 weeks. That was 3 weeks ago. Now the unit is freezing water on the bottom of the freezer and then leaking water on the floor. It is unconscionable that this company be allowed to defraud people to this extent. I will never buy a Maytag again and I would like to be informed of any class action suit. This company should be deeply, deeply ashamed of itself.

Because of the power of advertising, we replaced every appliance in our home in 2005 with Maytags. Since then, weve had minor problems with the stove and dryer, many problems with the dishwasher and washing machine, and complete failure of two Maytag microwaves, the last one was only two years old. The washing machine failures resulted in major flood damage two separate times due to two separate failures. Our refrigerator, model MBB2256GEW, has yet to let us down, however, since new it makes loud snapping noises that wake us up at night. It sounds like someone banging two large sticks together. Fortunately, I can repair most of these issues when they arise, but Id much rather get some rest like the Maytag repair man...

I purchased a French Door, Bottom Freezer refrigerator in the summer of 2006. Less than 3 years later, the ice maker door kept opening and closing and the lights on the door panel kept flashing. I called Maytag and found out there was a problem with the circuit board, and that it was under recall. The refrigerator was fixed at no charge and I was happy. Approximately 2-1/2 months ago, less than 7 years after I bought the fridge, it started getting too cold inside and then too warm and then too cold, etc. Then it stopped cooling altogether. From what I read, it was either a problem with the compressor or the relay on the compressor. There was a recall on the relay on some models, but not on mine. I cant even afford a service call. Let alone a repair charge. If the compressor is the problem, Im looking at a repair bill in the hundreds of dollars. The online price for a compressor is over $300. I dont have the money. So the beautiful refrigerator that I paid $2,000 for sits in the kitchen, unplugged. I never figured that Id pay that kind of money for a refrigerator and have 2 major problems with it in less than 7 years. I just got off the phone with Maytag and, of course, they cant do anything to help me. I was hoping to never buy another refrigerator, but if I have to or if I have to buy any other appliance, I will never ever buy another Maytag or Whirlpool. I will post everywhere I can about my experiences with this refrigerator.

Oven was purchased and put in May 2014. I have not be able to use. The oven temperature is off. If the oven is used at 500 degrees the temperature is really 900. I thought I had a gas leak because I got a bad headache because of the smell. The gas co told me to get a repair person to look at it. Maytag has been horrible to deal with. I have taken 3 separate days off trying to get it fixed. The last Maytag repair man had the nerve to ask me where the gas line was. He shut the wrong off and had a gas leak in my house. I had to open all windows. He was supposed to come back the next day. He did not and I received no calls. I have paid for an oven that is dangerous that I cannot use. I feel Im being treated this way because I am an older woman. I will never buy another Maytag.

I have Maytag refrigerator that is only 2 years & 9 months old that I am told by a service tech that it has a sealed system leak. So the unit runs it just wont get cold. I have lost all the food that was in the refrigerator & freezer and I told by Maytag that its not covered under warranty. The tech gave me a ball park quote of $600.00- $700.00 to repair the unit & I lost at lest $200.00 or more in food. I cant believe a new refrigerator wont even last 3 years & they wont fix their problem. So much for buying American made products. Whirlpool YOU SUCK & SHOULD BE ASHAMED!!!

We built a new home in 2008 and purchased a Maytag appliance package from Home Depot, including a dishwasher, stove and refrigerator. From the beginning, we had problems with our French door refrigerator (MFC2061HEW; it has been discontinued). Within the first year we had 3 ice makers replaced because it was not making any ice. Now, mind you, we went through Maytag to have their repairman to service our appliance and they set up all the service calls. We limped by for awhile and called a different repairman to come and check the fridge because it was not staying cold or making ice again and, of course, it was out of warranty. The first thing he did was check the freon and we were told that it didnt have enough freon to keep it going, so he recharged it and it worked great. We have had to have the repairman come back again this month because it stopped making ice and the temperature for upper and lower was all over the place. He checked the freon again and said the unit has a slow leak in it and he was unable to fix that. I contacted Maytag because I felt if the first repairman had checked the freon from the beginning, we wouldnt be having this problem. The only suggestion I got from them was call a company with a dye kit test and that they are sorry, but its not under warranty. I dont know about anyone else, but $2000.00 for a fridge that has been a pain since day one is a lot of money to replace. I feel they dont care about their customers and they should be responsible for paying for the repair that should have been caught from the get-go.

I bought this washer (Bravos Washer Model MVWX655DW) in June 2017. My wife and I did plenty of research and only complaint at that time was that it made load clicking noises. We bought it and it worked fine but never really filled with water to a level which would cover the clothes. Today I ran a load and brownish water was seeping out from underneath. When I lifted the machine my floor was covered with old stains which looked like oil or grease. I called a local service company and when they found out which model I had they refused to look at it. They said that particular model was known for having issues and when they fixed it, something else would go. They recommended looking online for reviews and calling Maytag.I did so and after explaining the situation to Maytag, they offered to send a technician to look at it to diagnose, not free of charge of course. While I cannot tell you avoid a particular company, I can say MY family will never buy Maytag again. If a washer is well known for having issues within its first 3 years and a company will not try to make it right simply because theres no recall on it I will spend my money elsewhere. Seems fishy that this machine has a ton of 1 star reviews within the last two months and Maytag does not want to eat the cost of servicing their junk.

I purchased Maytag washer/dryer set in Feb 2021. In June the washer broke. It took 2 weeks to get repair person to look at it. During the appt no faulty product was identified so they dont know what to replace. No parts were available. A follow-up appt was set for 1 month later. No parts are available to make the repair so a follow-up appt would be futile. . The only communications other than No Parts is that they want me to purchased an extended warranty. I will never purchase another Maytag product or recommend them to anyone. Meanwhile my warranty continues to time-out and they dont have any parts or idea when they will be available. Im not sure how a company can sell products that they do not have some level of support for those products. Beware of purchasing Maytag Products.

Purchased my Maytag Dishwasher MDB7749SBM on 5/13. 3 weeks ago the panel went out! I found others have had the same complaint on their Maytag Dishwashers too! I also learned this model was discontinued from Home Depot. Is this because Maytag knows this Dishwasher was JUNK and that they allowed consumers to buy this model knowing it had these problems - I believe so! I find it absolutely crazy that Maytag has not issued a RECALL and now I am out almost $700 plus if I get it fixed or buy a new one, I am out even more $$! There has to be some RESPONSIBILITY taken from Maytag!!! This Company was built on an excellent reputation but now this company reputation is considered POOR for selling defective products and doing nothing about it!

I will never buy another Maytag Product in my life again. The Bravo is the worst of the worst washing machines ever. They claim to save on water but the electric it uses is terrible. You have to be a magician to untangle the clothes. Anyone who had anything to do with the workings of this machine should be fired.

Our washer/dryer combination (2005 Maytag Neptune MLE2000AZW) has given us nothing but problems. The main problem is the stink from the washer. The unit is no longer usable and we are searching for a top loading unit to fit in the space. I am so angry - how did this piece of junk ever pass Maytags quality control?

Two months after purchasing our Maytag refrigerator, the light/cooling unit went out. After speaking with Maytag’s customer service and scheduling a repair company to come fix it, it took 3 separate trips over a span of 2 or 3 weeks to finally find the correct replacement piece to get it to work again. It is now 10 months since buying and we, once again, are having issues with the lights going out and randomly coming back on, the water/ice machine not dispensing, and we’re just waiting to see if the cooling unit isn’t out as well.I called Maytag as soon as we noticed the issue, and after waiting 15 minutes on hold, they scheduled a repair service to come check it out... in 5 days. Having spent $2300 on a refrigerator for our family, we were hoping for a reliable product. I would NOT RECOMMEND this refrigerator and will never buy anything, or let any friends or family members purchase anything, Maytag manufactures ever again. As if the faulty product itself weren’t bad enough, I have had the absolute worst customer service experience. Who would have thought it could be so difficult to look up a customer account, even after having it registered with Maytag after purchasing.

Same as all the other reviews control panel intermittently started to fail. Dishwasher is less than 3 years old. Does not work at all now. I tried resetting circuit breaker - nothing. This unit was $700 from Home Depot. Complete trash. It is cheaper to buy new dishwasher than repair - how unfair! Maytag won’t repair - well for over $300 they will. I feel better knowing everyone has same issue & is not my electrical system. Class action lawsuit!

Maytag washer mvwc565fw: You have heard about how noisy they are & dont fill up enough water unless you set it on deep water wash. I cant get the right water temp. Its cold, cold warm. No hot at all. Sorry I ever bought the piece of junk. Only have had it a month too. The last washer I had it at least lasted 4 years. Wouldnt recommend it to my worst enemy.

Ran washer with extra rinse and clothes came out with dry spots. The only way to get clean wash is to wash everything on bulky/sheets. We lost every appliance in Sandy. If I had known the machine was so-called water saver I never would have purchased it. I was in a hurry. I hate the machine.

I bought a Bravo washer 4 years ago from Home Depot. The spin cycle is stuck on high speed and sounds like a jet plane. Repair man came and said don’t bother to fix it because the bearing is gone. The machine cost close to $900. The repair man charged over $100. We are two retired senior citizens who dont do lots of laundry. I have read numerous complaints about the Bravo washer very similar to ours. Elder abuse should protect us from Maytag’s thievery and lack of help in repairs and replacement. A class action should be in place to address the Maytag Bravos manufacturing defects. There should be a recall and some type of reimbursement on this product . Please help us with this unjust situation.

I purchased my Maytag Centennial Commercial Technology MVWC200XW in May 2012. This is the second time in almost 3 years that it breaks down. The basket decided to drop today and by the time I realized that it did, my whole bathroom had flooded, the water spread down the hall into my spare bedroom and soaked through the floor, also flooding my basement. I called customer service. They are sending a repair man next week, but as for all my ceramic tiles that are now cracked in my bathroom and my hardwood in the hall and bedroom that is full of water and are lifting off the ground. Its my responsibility to call my insurances to fix it. Yet it was their washing machine that caused the damage in the first place. When I purchased the washer I didnt expect to have to repair it every year. Not impressed! I do not recommend this washer.

Bought a Maytag dishwasher early July. Worked great for 3 months. Drain pump went out. Called customer service, 30 minutes to get a person. 1 week to get a service tech here. Even though we told them pump was out. Sent with no repair parts. So has to come back at our inconvenience, company policy, not service tech fault. Tried to complain on live chat. 30 minutes for them to get with me. Still no satisfaction. Would not recommend the product for the company itself. Sadly thought we upgraded.

Maytag Bravo washer and dryer purchased April 2011. Dryer works fine and am pleased with results. Washer does not clean simple dirt and stains off clothing. Washer never fills to a water level that covers all the clothing. Some clothing never gets submerged, thus simple stains never get water contact throughout the cycle. I now spend more money purchasing spray stain removers and using the heavy duty cycles and extra rinses, would have been better off getting a Kenmore with an agitator. The concept does not work.

A pure piece of junk this wash machine is. It is more of a merry go round than a wash machine. I do not understand how it can be called energy efficient. All it does is spin and spin and clothes come out as beautifully dirty as they were loaded. If you make the mistake of putting a few extra clothes (machine calls itself a large capacity), clothes bunch up and one has to pull them apart. The bleach dispenser was used as one would use a bleach dispenser. However it is all rusted. I had bought extended warranty from Lowes but Lowes did not honor the warranty saying rust was a cosmetic issue. Yet when Lowes sold the extended warranty, they did not specify cosmetics were not covered. It is not even cosmetic. It simply is cheap enamel paint.I have used 200 dollar wash machines but never have I experienced such a horrible and annoying product. I will try one more time to see if Maytag will help out with the rust issue. If not, I will simply cut my losses and buy a regular cheap machine. Maytag should be ashamed of itself. I bought a Maytag because I thought they made the best machines!!! Oh! Well, maybe they did at one time.

I purchased an Atlantis washer in 2005 and assumed that Maytag was still one of the better manufacturers. How naive of me! What genius at Maytag thought it was a good idea to place the water filter inside the washer? Not only can you not keep the filter clean so that cold water will flow properly, even worse, if the filter completely clogs, the water will not stop filling into the tub which could, of course cause an overfill and flood. I narrowly escaped this scenario once. No one should have to stand and watch their machine fill with water to insure it stops. Now the machine is causing a grinding noise when agitating. I expect it to stop working any day. I will not buy another Maytag or Whirlpool, who of course now owns Maytag. And I will not pay another repair bill for the filter or any other part. The brand was once considered the best in America, now its just another brand thats a piece of junk produced in another country.

MY MAYTAG WASHER and DRYER ARE 17 YEARS OLD. THEY are FRONT LOADERS WHICH I THINK MAKE A DIFFERENCE. I BOUGHT MAYTAG because I had trouble with Whirlpool products that didnt go the test of time. The only problem I have with my washer is the mildew.

Within a year of purchasing this washing machine, I needed to schedule a repair service because the washer started making an unfamiliar noise. Repair Service shows up and refuses to touch my washer. The ink on the Serial and Model number (stick on label) inside the washing machine door has washed off. Sticker label in excellent shape, except all the ink has come off. If the Repair Serviceman cannot read the label, NO SERVICE FOR YOU. MY SAGA... Did you know that if your washer or dryer does not have a readable serial number on the machine, NO repair service will work on it. It does not matter if you have all the paperwork showing this information. If the original label is unreadable, no repair service will touch it because they will be fired. Maytag changes parts on a model all the time. The serial number is the ONLY way a serviceman can tell exactly what parts your washer was made with. Apparently the serial and model number label sticker was not printed with permanent ink. The Repair Service said the Serial and Model number ink washed off the label because the sticker was incorrectly put on the inside of the washer door at the bottom. But they were WRONG! Maytag shows online that is exactly where the serial and model number sticker is supposed to be located. So, I called Maytag to order a new serial number (stick on) label for our washer. I gave Maytag the information and I was told I would have the label in two weeks. Then I called back a week or so later to make sure the serial number was ordered and on the way. Maytag said there was a misunderstanding, and that they received my request on 6/17/15 and it was sent to the ONE AND ONLY GUY that makes replacement serial number tags and he was sent my request on 6/22/15. Maytag said it would take the one and only man quite some time to make the label (SINCE THERE IS ONLY ONE!!!) and I could expect to receive the replacement label in 4 to 6 weeks and they were sorry, but there was absolutely NOTHING they could do about it. So as my year old washer sits for over a month, Im going to the Laundromat each week. We should have received the new serial number on August 6, 2015. So it’s taken almost 2 months and my label is close to two weeks late. To date I have not received my serial number. I tried to use MAYTAG chat, dont bother, they said they couldnt help me. I needed to call in. So I emailed Maytag today for their support services to tell me WHEN I can expect to receive my new serial number label. I bought this through hhGregg. Check your Maytag washer. IF THE SERIAL NUMBER AND MODEL NUMBER LABEL ARE INSIDE THE DOOR, CHECK TO SEE IF THE INK IS COMING OFF THE MACHINE LABEL, and order a new one NOW if it is, or you will not be able to get your washer serviced. Do not put new label back on the inside of the washer door. This is just unbelievable.

I bought my Bravos x washer and dryer set three years ago. Ive never been happy with them. You have to put the washer setting on bulky to even wash a normal sized load and they still dont come clean. Only three years old and Ive had problem after problem with the washer. As Im typing this I have a full load of clothes in the washer that will not wash, its full of water and wont even drain and spin. PLUS the lid wont unlock. So aggravated.

We had a Fisher & Paykel Washer that lasted 14 years. This Maytag Bravos XL washer has been the worst machine I have ever owned. The clothes come out dirtier than ever. In todays world all technology is becoming disposable, Where is the Maytag repairman now? I have tried all of the settings, to have a decent wash. I am ready to throw this out. Lowes you need to do something about this. It may be made in America but now we know why Japanese and Korean electronics just work! Damaged Clothes/Clothes not being washed thoroughly enough are my biggest pet peeves with this washing machine.

We bought the highly rated Maytag Bravo washer and dryer in March of 2010. In less than a year, the dryer broke down and the drum drive belt had to be replaced under warranty. Last month the washer drum stopped turning. A & E Factory Service quoted $466.87 to replace the bearing that had failed. We have hated this washer since the day we got it. So, it wasnt hard to buy a Samsung front loader and have the miserable Maytag hauled away to wherever badly designed machines go. Trying to wash clothes using high speed spinning instead of water causes excessive wear on the clothes and the machine as well as tying the clothes in knots. It is one of the worst mechanical designs I have ever seen.

My dishwasher is 3-4 years old and the control panel is malfunctioning. Cant push a button to choose what cycle I want, it doesnt respond. I went to the Maytag website to see if there have been others with this problem. It appears that there are many other people having this problem. Parts are not available and it seems that Maytag wont do a recall on this product due to the control panel malfunctioning. I have been dealing with this problem for the past few months. I dont think Maytag is worth the money. They want if you only get a few years out of them.

In 2013, $1850.00 I purchased a Maytag double oven, $700.00 Maytag dishwasher, and a Maytag refrigerator for $2200.00. I have had nothing but problems with all of them.... The oven locked up on me had to call a repairman to fix it. Ive had to replace the control panel on the dishwasher... And the refrigerator!! (WHAT A NIGHTMARE) In 2013 just received the appliance they had to install a heater in the ice maker because there was condensation. 2014, Refrigerator dead.. Repairman had to replace interface and control board.. 2017, Icemaker crashes and had to be replaced... 2020, Now here we are again Ice maker crashed again! (JUNK). My wife told me that she has had nothing but good luck with Maytag appliances... Never again.

I thought I was nuts - only 2 of water in a full machine of bedding or clothes. I agree with all the other one star remarks - clothes still dirty, still dry, hardly any water and if you use the bedding selection, it takes nearly 2 hours to wash a load and then it doesnt spin dry so you have to rinse and spin again. Very disappointed with the machine. Yes - class action lawsuit? How do we do this.

Bought a new home in July of 2016 and the builder had included a Maytag Bravos XL washer and dryer. They are THE WORST performing appliances I have ever used! I will replace as soon as I have the means to do so. DO NOT PURCHASE the Maytag Bravos XL appliances. The engineers that designed them should be fired! The washing machine makes an incredibly loud noise (like an old starter grinding in a 50s car). Im told that this is normal for the machine. Does NOT clean well and leaves soap spots on dark clothes... leaves them on light clothes but I cannot see them. Whites come out dingy even with bleach. The tub is so deep that I have to use tongs to get out smaller items, I am 53 tall and have never had this issue before. Soap dispenser drawer wont stay closed during wash cycle. Clothes are so badly tangled during the wash cycle that it is hard to describe the wrinkled mess that has to go into the dryer.Dryer issues: Very loud. Very wobbly and unstable, and yes, it has been leveled 3 times. Bed linens have to be separated at least 3 times during the drying cycles because they twist and wad up into big, wet knots of cloth. Infuriating!!! Dry time is very long unless you wish to cook your clothes. So disappointed in this product. Total rubbish!!

What was shown on tv and the way it looked in home depot were much different when I got it home. The refrig. Is big as a bo car on the outside but inside nothing.

I purchased this new Maytag washer (Model # MVWC300XW, Serial # 12621033) from Hahn Appliance Warehouse in Oklahoma City, OK 73107 on November 23, 2011. It is less than six months old, and the transmission has gone out. Hahn advised me that they had to go through Maytag Service, and they would only replace the part. I contacted Maytag/Whirlpool Service Corp. directly and spoke with a manager named David, who informed me he was sorry but would not authorize a refund or exchange for a better product because this was the first service call. I am very dissatisfied with this product and with the service standards that Whirlpool/Maytag offers on their products. If I were to sell a product that I knew has had numerous complaints, I would pull that product from my line offering and make either a full refund or replace with a higher level service product.

Washer Bravo MVWX655DW0 - Maytag has shipped the wrong part twice, sent me the right part which is faulty and the 4th one arrived today. I have not had a washer since 9-16 October 9, 2017. I am writing to tell you about my experience that Ive had with Maytag over the last 30 days. I have owned several Maytag and Amana appliances in the past; along with owning several currently. Over the years, weve had a wonderful experience owning these appliances however the last 30 days is one that has been unbelievable. On September 18 on a Monday early in the morning I called Maytag service line. I spoke to a young lady who had difficulties finding me in the system and did not know how to make an appointment to have a Maytag repairman come to my house to look at my washer. I did not take down her name as I thought and trusted that the company was acting on my behalf and would take care of me.I spent several minutes explaining to her that I did not live in Indiana that I lived in Iowa and that I would need a repairman who is close to my hometown. She continued to give me phone numbers with area code 407 in Indiana and then kept repeating some type of a ZIP Code 49 something for Indiana. I explained to her four different times that the zip codes in Iowa start with a five and the area code would be a 515 number in the area she was looking at. She finally gave me two phone numbers, one that did not work. I asked for a repairperson out of Jefferson. She told me Cranston Repair and gave me the phone number. She told me to call him. I told her that I would go with the Cranston repair since Jefferson with my hometown and it was close to where I lived.I then asked her if she would make the appointment. She told me she didnt know how to make the appointment and she kept messing up with the system. Not sure if it was her first day or not but that was fine so I said “never mind I will set the appointment up myself. I then asked her to double-check to see if our new Maytag refrigerator that we just purchased was registered. She told me she did not see it but all I needed to do was call back the next day with the model and serial number and anybody I spoke to on the phone could go ahead and get that registered. I thought I had registered online; I only wanted to double-check but she didnt see it so I assumed I did something wrong and then would make the call back the next day.I called Cranston repair and scheduled an appointment with the repairperson for the next day Tuesday, September 19. Repairman came the next day on time, looked at the washer and found that the transmission had gone out. I had purchased the washer just shy of two years ago. The repairman said that he would have to order the part and would let me know how long it would take and would return to fix the washing machine. He called from my house and was told that the part was on backorder until October 5. After the repairman left the house I decided to call Maytag back and express my disappointment in the product as Maytag says they stand behind their products and the fact that it was not even two years old and that a transmission would go out. The individual I spoke to this time, Antcwaniqua? Not sure about spelling, listened to my story. She also told me the part the repairman ordered was not correct.I needed part W1 1132267. She said that was a substitute part for the correct part that I needed which was W11035204. I told her that the part number ending in 204 we were told was on backorder until October 5. She said no, the part may show that in the system for repairmen but Maytag can locate the part in a warehouse, it would be shipped in 3 to 5 days. I told her that he had called a place in Davenport, Iowa. What she would do because of all the issues I was having was she would go ahead and ship the part out to me at no cost in 3 to 5 days.I wasnt sure about that warehouse thing. It didnt sound convincing but at that point I had to go along with it. What was shipped out to me was the substitute part W1 113-2267. At this point she told me that I would have to pay to have the part put in; I agreed to that on I want a new washer or I want my washer repaired within 72 hours at no cost. I have not had a washer for 3 weeks plus. Repairman in coming Friday and I am not confident that the 4th gearcase part that came today will work either.

The 2013 Maytag dishwasher panel broke 13 months after the purchase. After several phone calls and complaints they agreed to replace the panel at no charge. Since yesterday I have the same problem and need them to replace this washer. I am on a limited SS income and I am not in a position to purchase another washer after 3 yrs. My previous one lasted almost 15 yrs. This is totally unfair and I hope that Maytag replaces this entire machine, not just another repair. It will cost them a lot less to do that by either sending or having LOWES to replace this one. Thank you so much.Updated on 09/16/2016: Maytag is asking $300 to fix it and they will not replace it. So, by coincidence a friend of mine had the same problem and she did the following and I repeated these steps and now dishwasher is working. Turn off the switch or unplug, or turn off from the circuit box, your dishwasher. This cuts off electricity to the washer totally. Wait 30 seconds. Push the cancel button and hold on pressing it for 30 seconds (precisely, not less). Push then, the start button and hold on for 30 seconds again. Turn on the power and the cancel light will come on and let the cycle finish do not touch anything, until it is turned off and the light goes off by itself. Then, choose your selection for washing push start and see if it works. It did with mine and hers. Good luck and LADIES- YOU CAN DO IT, if this little old woman did it by herself.

Maytag Bravos Commercial Washer MVWX500XWO - This has been the worst experience with this $900 washer and breaking down in less than 2 yrs. Complete Garbage, New Locking Mechanism, now spin cycle not working. I am about to take back to Home Depot and let them have it. Garbage product - NOT WHAT MAYTAG USE TO BE... NORMAL 10 YRS NO ISSUES THIS MACHINE - STAY AWAY FROM.