I purchased a Maytag electric range model # MER8775AS in Feb 2012. While boiling syrup, the pan overflowed onto the oven door. As I began to clean up the spill I noticed that some of the spill had gotten inside the door on the inside of the oven glass. To remove the stain would require disassembly of the door. I called Maytag and complained of what I called a design flaw and they said, No, its your fault for spills entering the door. They even sent a condescending email to me informing me that if I needed to purchase parts, where I could get them. I designed appliances for years and this is another example of poor quality and lack of consumer service. I AM DONE WITH MAYTAG.

I am not dissatisfied with hhgregg, but with Maytag products. I purchased the Maytag Centennial Top Load Washer and Maytag Centennial Dryer to match. I was a bit leery of the new energy star models that use he only type detergent, but decided that was the newest and greatest thing out, so how could it be wrong? For the past two months, I have been sooooo very disappointed in Maytag. Neither of these brand new machines are worthy of being considered brand new. The washer takes extremely too long to wash a normal load, too noisy, and has ruined several items of clothing, due to malfunctioning distribution of bleach, fabric softener released after clothes are through washing. There has also been several times that the load wash is complete and the clothes are not even wet (like they were never involved in a wash cycle). As for the dryer, you have to run it through two 40 minutes cycles to get the load of clothes completely dry, so much for energy-saving. This is my first complaint to anyone, but after reading several reviews on Maytags website, I am reassured I am not alone. There are hundreds of other dissatisfied consumers of this Maytag product. I will be writing a letter to Maytag, requesting a refund.

Maytag Bravos Quiet Series 300 - My machine is 3 yrs old and started making a very loud noise on the spin cycle. My last Maytag lasted 18 yrs and all my appliances have always been Maytag. I believe it now when Im told that Maytag does not make good quality washers anymore.

We (family of 2) purchased our Maytag Bravo XL Washing Machine Model#MVWB880BW in Nov. 2013 for over $700.00. Last week, Dec. 2019, the washer would not finish the rinse/spin cycle. The clothes were still wet. I researched troubleshooting in the Maytag booklet included with the machine and tried everything. It still showed an OL on the readout. It was not overloaded as I only had 3 towels, 3 washcloths, and 3 hand towels in the washer. I tried just the rinse/spin cycle alone to get the water out of the clothes, but they remained wet, and the OH still appeared on the machine. When I called the place where we bought it, they suggested unplugging it, waiting and plugging it back into the outlet to possibly reset the machine. That seemed to work for 1 very small washload. The next day, I tried washing again and the OH appeared with the clothes still being wet. We had a repair person come out. The service call/diagnostic of $116.98 plus repairs of $304.41 plus $95.00 to install of the new Motor Control Board. I feel that cost is excessive for only 6 years of service. Before we bought this machine in 2013, I had a Maytag which lasted over 20 years with NO problems. I always thought Maytag was the best washer, but this experience has proven to change my mind. We went out and bought another washer rather than replacing the board not knowing how long the new one would last. Needless to say, we did not buy another Maytag. I do not feel I can trust the Maytag products anymore. After this experience, I did more research on the Direct Drive used in this particular model washing machine and found that it had been problematic. I would have thought Maytag would have offered a recall to avoid these costs/problems and avoid dissatisfied customers. Along with the original purchase of the Maytag washer in 2013, we did buy the matching dryer and are hoping the dryer will last longer than the washer. We shall see.... This has been an unexpected and expensive lesson.

Should have researched before purchasing our Maytag Bravos MCT washer! We purchased it at Home Depot and it was delivered and installed by a certified technician. From day one it has been so loud and obnoxious with the way it “knocks” and “clicks” when it runs through a cycle. When it spins the whole machine shakes viciously, despite being balanced properly at installation.We have owned this washer just short of two years and for the last 8 months we have had to keep unplugging it to reset it so that it will even run through one cycle. The most recent two months have been extremely frustrating, due to the fact that not even troubleshooting can aid in “fixing” the fact that this piece of crap washer will not complete a wash cycle! It either stays in sensing mode & doesn’t add water, or it adds water but doesn’t do anything but sit still for about 15 minutes and then drains all the water back out and stays stuck on “wash”. We are researching online and have found many similar complaints with the same negative experiences. Our next step will be to call a repair person! What a crock!!! Maytag gets a big “thumbs down” from us!!!!

Buyer Beware!! Purchased my Maytag over the range microwave in May of 2014. It has a manufacture date of Feb. 2014, and it is now Sept. 2014. It is a very nice looking unit but a bit oversized. My handyman that installed it had to raise my cabinets above my stove two inches to avoid it being too close to the range. The motor is pretty loud and It often times does not heat evenly. The light on the unit that shines down on the range is not much better than the power of a night light which is a bit disappointing considering it looks like a higher end unit, and down to the reason I am writing this review today is that for the first time I went to change the bulb. I unscrewed the the light cover which is placed awkwardly toward the very very back of the unit, only to find that when I went to twist out the burnt out bulb (that has been in there since I purchased the unit) that the bulb broke off after hearing what sounded like the break of a seal of glue, and the bottom aluminum piece of the bulb is stuck in the bulb socket. I found that the bulb is placed in an awkward place behind the light cover. Instead of the bulb facing to the left or the right or to the front of the unit it is facing toward the back which is making the bulb socket impossible to see, which means that in order to screw in the bulb you are screwing it in from an angle that you cannot see unless you climb on the range and lay on your back, or get a mirror to help see where you are screwing in the bulb. This is just a very awkward and unpractical design coming from such a well known company with such a common and ordinary product. Now I am sitting here writing this review and I am trying to figure out how I can remove that little piece of aluminum stuck in the light bulb socket and since it is not facing to the left or right and facing toward the back, it leaves me about less than 1/2 space to work with using my hand or a tool to remove that piece, or I can just leave my broken bulb piece in there and screw the cover back on until I call service for Maytag. I believe it is still under warranty but from others experience that I have read about I am not feeling confident I will receive great service or a desirable outcome. Wish me the best!! Thanks for listening!!

Machine is very loud. Clothes do not feel completely clean when wash cycle has finished. I have a sense that not all soap has been removed. Dark clothes have streaks of white residue. Must turn clothes inside out before washing. Very disappointed.

My front load Kenmore just fell apart. I guess Im lucky I have had it for 8 years and now its broke. I could fix it but thought it would be better to get a new one. I looked at all the reviews for front load washer and could not find one that had positive reviews. So I went with a top load. After reading all the complaints I might have made a mistake, but its too late now as it was delivered yesterday and now doing the clean cycle. Oh my…what junk they all produce now - a true throwaway society. My refrigerator is still working after 24 years what a gem of a product. Happy days.

Side by side refrigerator model #msd255oveu01. I bought this refrigerator Apr. 2011... The 1st year, the ice kept sticking in machine or freezing up. Now they have had to replace the modules 3 times. Once fall of 2012 and and again yesterday, 3/19/14 and they had to come back today to replace that one. I have called Maytag and they wont stand behind it since the warranty is over. I have told them that this is an ongoing thing with the ice maker and I have had to have it serviced ever since I have bought it. I told them from the git go that the ice maker needed replace. The ice dispenser also drops an ice cube on the floor on occasion and if I use crushed ice it jams up. This product is defective and is not a good product.

I have just inquired on this site about problems with Maytag dishwashers. Ours does not start. It is about a year old and is Model MDBH989AW03. I am very discouraged after reading the many continual problems with control panels. I am checking my warranty. If it is out of warranty, we think that we will purchase a GE that has worked great in our other house.

Since the day the Neptune washer and dryer were installed, the washer has given me nothing but problems. It vibrates so badly and dances all over the floor.I have had the repairman over at least seven times and, now, it is out of warranty so I am spending my own money. The last service man was from Hurst Appliances in Regina, SK. He removed the pedestal to see if this might be the problem. He also sold me some foot pads for $50 that he said might help the problem. However the machine is still vibrating and the terrible mold smell comes out of it as well. I am thoroughly disappointed in this product. I will never buy another Maytag product and tell my friends not to as well.

I purchased My Maytag Washer and Dryer set from Lowe's, which was a very good experience all the way, back in June 2017. After two years I can finally give an honest review. We love this set even though it is not as quiet as the old Maytag washers. Still is but not as. We have not had one bit of trouble from either the washer or dryer. The next size larger would have been the better choice for us since we now have king size bedspreads to wash. It still does the job though, just one piece at a time. A lot of people complain about the smaller amount of water used but it still cleans clothes quite well. If you need more water just use deep water wash or for even more water use the setting for bulky sheets which really fills up the water level.

I purchase my Maytag electric glass top stove 9 years ago. 2 years ago, one of the burners went out and had to be replaced. Now, in the past 2 days, my oven is taking FOREVER to preheat from 0 to 455 degrees. So far, its been 78 minutes waiting for it to go from 0 degrees to 425! Apparently the heating element is defective. As far as the self cleaning oven, it is absolutely worthless, and does NOT work! Needless to say that Im very disappointed, and looking at another repair expense!

I specifically bought the washer because it has an agitator and you have a setting for more water if you need it. My previous washer had no agitation and really miss that. Seemed like clothes got cleaner. On this machine the agitator is certainly helpful, but there is so little water sometimes I find a pair of jeans with dry spots when load is complete. No, I do not overload the machine. If I change the setting to add more water I don’t see a difference in the amount of water that comes in. I find myself frequently adding an extra rinse. I feel that while making the new washing machines eco friendly they have cut back on water conservancy too much. At the very least the consumer should have more options as to levels of water. I would not buy this brand again.

We purchased the washer and dryer in June 2009. This past weekend, I noticed that the washer was leaking. The price to fix it is half of what a new machine will cost. I am very disappointed in Maytag. When I purchased the machines, I thought I was purchasing a quality product. Ive had paid much less for washers that last longer. Needless to say, I am shopping for another washer this week and it will not be a Maytag or Whirlpool. They are pieces of junk!

I just purchased this Maytag Commercial Technology Washer and Dryer on August 31st, 2018 and We hooked it up today Sept 4th 2018. I put a small load of towels in this machine and it said it would take an hour and thirty seven minutes to wash. I added my detergent and pressed all of the necessary buttons and started the load. the machine started spinning and testing and adjusting. I waited to hear the water start to come into the washer but nothing. I then checked my water lines thinking they are not on but they were. Through the smokey glass on the washing machine, I could see water dripping as if it is hooked up to a slow drip IV Machine.I am taking this thing back ASAP!!! First thing in the morning on Sept 5th 2018 I do not need to call Maytag Customer Service because they know it is a piece of junk, so I do not need to waste a moment with this crap on my property. I see Maytag does not believe in a QUALITY ASSURANCE DEPARTMENT because that department would put a stamp of approval on this Junk for distribution.No Washing machine should take more than 30 minutes (40 mins max) to wash no clothes. I will have to invest in an old school scrub board and rocks, then I can understand an hour and thirty minutes worth of wash time. I have set the timer on my phone when I started this load and My towels have been in the washer for an hour so far and I can still hear the slow IV DRIP OF WATER going. I just checked the machine and the digital reading is saying it has an hour and thirty three minutes to go. there is no water in the tub of this washing machine. The towels are wet from the IV drip and the machine is now pretending to agitate the dirty towels but it is only going in one direction. It is truly a sad state of affairs, your hard earned money gets you nothing but junk and a runaround.

2 Year old washer. First the actuator was replaced. A 150.00 charge. Two months later the pump is shot. Another 200,00 to replace the pump. This is worst piece of ** washer I have owned. I would not recommend to anyone. Stay away. I would give it 0 stars if I could.

Approx four months ago we got new stainless steel Maytag fridge, stove and dishwasher. Terrible, terrible, terrible. The dishwasher rack was broken, and the parts are plastic and hardly any room on the racks. The fridge had the wrong hinges and doors on them. We have been waiting for four months to have them replaced. Today we checked with Maytag and still not coming. The fridge makes a very loud humming noise it almost shakes the floor. This was some sort of compressor problem. Now the fridge is having problems with the freezer. It is freezing up with frost everywhere. The stove is terrible. I waited an extra month to get a convection oven which I have had before and this one is terrible. The double oven is a great feature if they work. They take forever to heat and if you do anything with the food you have reset the temperature? The top is the worst for cooking as the only one that works fast is the boost but then it slows down and you have a hard time cooking the food. The black top is very very hard to clean. I have owned a Maytag washer and dryer for the last 34 years. They have been excellent. Since Whirlpool took over Maytag they seem to have run the name into the ground and all the good service and products they had built up are now ruined. I told my neighbor a few years ago to buy a Maytag washer and dryer and they did. They have had nothing but trouble and are now having to buy new ones but not Maytag. It is a shame that with all the technology that Maytag has built up over the years is now gone. If you look at all the terrible reviews I dont think Whirlpool will be in business much longer with products and service like this. I still have a fifties fridge for pop and beer and it is the best fridge ever with no problems and my last fridge in my garage, that I replaced with this Maytag is still better than this new fridge. The service man that came to fix the fridge said we had to build in the fridge to keep the noise down. How come they never had problems with Maytag products years ago. I feel its all about the almighty dollar. They only last a few years and you have to buy expensive warranty. If you made them properly you would not need warranty and they would last for years like before. If anyone knows if there is a class action suit against these companies let me know since all of us should not be ripped off and costing us time and money.

Almost 2 years ago this dishwasher wouldnt drain. Fixed that $300. Then just over a year ago control panel had to be replaced. Now control panel was bad again, had to rest circuit to get it to start. I see this is a common problem. Only 2 of us in the house and the dishwasher gets used only 2-3 times a week since we purchased brand new in December 2011. Ordered the new control panel and just went to replace it, guess what. This appliance could have burnt our house down. The wiring in the door that plugs into the control panel is burnt! Not at the panel at all but a good 8 down the wiring harness. Both harnesses as well. Scared me half to death! To think it could have killed us at night, when we usually run this appliance. Definitely calling Maytag now. I do have pictures as well.

Maytag Microwave MMV4205DW-1 - This microwave made it one year and one month before the door would no longer latch shut and the control panel stopped working altogether. Called Maytag and was told not under warranty. It was going to cost more to repair than to purchase a new microwave that was a different brand.

The oven works. However, there are two safety issues. First, the flat metal panel above the air vent and below the instrument panel gets extremely HOT. This is the location we can easily touch, especially when we operate the instrument panel. We almost burned our hands. Second, the edges of the unit are very SHARP. We almost cut our legs. These are serious safety issues. In addition, we/I tried to post a review at Maytag site pointing out these safety issues. The review was twice moderate (i.e., rejected). Even though I used to like Maytag, this experience changed my mind.

We purchased this washer from Sears. Its always been loud during spin, but the past couple months it has gotten VERY loud. It jumps around. Also, it tends to ball clothing and towels. It has been hard on my clothes and bedding. Many times I have to rewash towels and bedding, even jeans at times. I have been very unhappy with this purchase from day 1. It was not a cheap washer.

Bought this machine last spring with high hopes. When I noticed issues, I looked up other reviews and saw so many having the same experiences. It does NOT use enough water to clean or rinse the clothes. My clothes are getting stretched and worn. I have to run extra rinse cycles to get the detergent out of my clothes. For the cost of this machine, it should be working much more efficiently than it does. Not seeing any savings in electricity or water bill due to extra cycles needed. Waste of time and money. Would love to join a class action suit against them for the piece of junk!

Bought brand new Maytag dishwasher. Worked great for 3 years. Then caught on fire. Couldnt contact maytag for a month because when you call your on hold for 30 minutes. Then when I do contact them they will only want to give 50%off another of their products that Ive already had catch on fire. I will never buy another one ever.

We were delighted with our new Maytag refrigerator, model #MBF2258XEB, until the compressor died less than a year after we bought it. Home Depot, where we purchased it, directed us to the A&E Company for service. Two weeks later, we are still without refrigeration; Maytag refuses to replace it and even refused to overnight the new compressor. We thought Maytag set an industry standard for excellence. Don’t buy this product if you want a reliable refrigerator from a company that stands behind its products.

Things that I have read that are true: Rips clothes/towels/sheets. No real problems with motherboard like some have stated. Bought Maytag Bravos Washer/Dryer in 2009. No real problems with the dryer, HOWEVER, may with the Washer. Had the pump go out in 2/2010 to the tune of $199.20 due to a small object in the pump. The repairman said it would just take a very inexpensive part from Maytag to prevent this. In 6/2012 washer not draining, clogged pump. All right, new to HE Washers, so told to use less detergent than detergent manufacturer recommends. $79.13 to fix clogged drain. Even though being careful with items in pockets, loose buttons, etc. AGAIN had pump go in 1/13, $214.22 (same problem cheaper in 2010, repair inflation). Wed noticed it was loud on the spin cycle (like a rocket going off) and were told at that visit the bearings would need to be replaced, and quoted approximately $280 to repair those. Havent fixed, waiting for something else to go wrong and then decide what to do with it. So in 4 years paying almost the purchase price of the unit (if I fixed bearings also). Crazy. If you bought a house and had to pay 4/5 of the house to repair it in that short of a time, no one would own a house!!!

I am so fed up with my Bravos XL washing machine, that I felt compelled to vent and see if others have the same issue. The first two reviews I read complain of the same thing as I am finding. Some kind of scummy residue on my dark clothes, need to rinse, sometimes soak again to get the residue off. Have tried many different detergents. The guy at the store said try cold water! Yeah right. I use half the amount recommended. We have two boys who play baseball. The seller said this would be a great machine. Id almost consider trying to sell it on Craigslist and buy a good used one with an agitator. Spent a lot of money on a fancy looking machine. Definitely overpriced and overrated. Do not buy this machine!

I purchased a Maytag Bravos washer and dryer 3 years ago, thinking I was buying a high quality washer and dryer seeing that it has the Maytag name on it. When it was nine months old, I had to have the complete tub assembly replaced. Now coming upon three years old, I am having similar issues with the machine so I called out a repair service out to see what my options are. Come to find out this time that the shocks that support the tub are bad. All three of them need to be replaced at a price of $455.00. At this point, it is not worth putting the money into it. Maytag, 3 years old and I am having to start shopping for another washer. It will not be a Maytag.

I purchased an over the range microwave (OTR), boxing day 2018. It failed January 2021. It worked great before failing. The issue with Maytag/Whirlpool is their service. I told them before they came out that I was only interested in having it fixed if it could be done that day. They checked that they had the parts and said they could do it, so I moved forward with the appointment. Well they didnt fix it, and said that they need to order a part, which they said would take several weeks. They are trying to bill me the service fee $167, and expect me to wait a month or possibly more to get the part and fix the microwave. Now Im faced with having to pay a service fee for something not fixed and buying a new microwave. Lesson: Never try to repair, cheaper to buy a new product. Other lesson, never buy Maytag or Whirlpool product again. Despite what is on their website and advertising, they have terrible customer service.

The washer is so loud it can be heard all over my home (my home is 2700 sq.). It sounds like metal to metal grinding. I was told thats how the run and the first bit of water isnt enough to even wet the clothes. Id never buy another one (even though this is my 3rd Maytag washer. Im 78 yrs.old).

After purchasing this washer in 2007, the washer started to smell like sewage. At first we werent sure it was the washer and had a company come out to check the pipes. After this and calling Maytag complaining without any luck. We were told to buy affresh tablets and run it through the washer once a month. This last only so long and the smell comes back. Now when the washer goes into the spin cycle it sounds horrible. Again called Maytag without getting any resolve. I will never buy a Maytag again!

Maytag Neptune Washer Drum Bearings have once again failed. Last time, I replace the whole drum via diy, cost was about $160 for the part. Now I see that outer drum is $500 +/-. I just may only replace the Seals & Bearings this time OR just part this thing out and buy a real machine without the Maytag name.

We bought the Maytag set of dryer and washer just over 5 years ago with ex. war. The dryer now doesnt heat up but the drum does turn. To fix it would cost about $500 maybe more and the parts may only last a few months. I believe that dryer should last longer when only used about once a week. I am now looking at Speed Queen. Cost more but am told they last longer.

We bought this stove in 2014. One knob got stuck while my teenager was cooking food on the gas stove. He called me at work worried because he couldnt turn it off. My husband left work right away to go home. We thought it was just a bad plastic knob. Now a second knob is stuck in the on low position. There is a third knob that feels hard to turn. That will be 3 burners. This is ridiculous. Its a safety hazard. We consumers have to worry if the house will burn down, get CO2 in the air, and if our family and children are safe. We thought Maytag was a good appliance. I will not buy another Maytag. They should recall this stove top/oven. I have read so many of the same complaint on this website as well as online in general. I cant believe they continue to sell this with this much of a safety issue. Please take it off the market.

I have owned this washer for three years and the smell in the entire area of my home is getting unbearable. I have used vinegar, clorox, and washer cleaner and I always leave the door open when the washer is not in use. My other complaint is that even a small amount of bleach cannot be used on clothes without causing bleach stains because it runs directly on the clothes before enough water is in the washer. The receptacle for softener also does not dispense the softener properly. I am very disappointed in this machine.

I bought model MDBM601AWB3 in October of 2009. The control panel and wiring harness burned in August of 2011 after, at the most, running twice a week. I called customer service and talked to numerous people. All said, Too bad, out of warranty. I did a quick Google and learned it is a common problem and even a fire hazard with Maytag dishwashers. My wife, who was being treated for lung cancer at the time and was very emotional, got a hold of someone in corporate and literally cried that we could not afford the $600 to fix a problem they knew it had when they sold it to us. They relented and agreed to pay for parts; we pay labor. Today, 1/10/13, the control panel is dead again. I suspect it is the same problem as all they did was replace the panel and wires. This machine has obvious dangerous design flaws that they were aware of. I find it sad that a company can screw people like this and get away with it. What recourse do we have now?

I have been washing clothes in different washers for almost 4 decades and never had a terrible washer until now. It has total control of the water level and it NEVER has enough water added. I have to add at least 2 full dish pans of water to every load. My washer does not allow you to pick your level because it does it automatically and no theres way to bypass this problem. It moans and groans for almost an hour in slow motion at its best. It should be illegal to sell such crap!If the intent was to save energy it fails when it runs twice as long as other washers. The instructions that are in the lid say that when you set it on deep water wash that it does not sense automatically-LIES! This lid must be generically made for other washers that they have because again, you cannot choose a water level. When a washer runs for almost an hour (this is not soak or extra rinse either) it is not saving energy over those that run for half that length of time. I wish I had returned it, but I listen to others who say that this is how washers are now. I still owe 150.00 on it and hate writing that check.

The salesman tried to convince me to purchase a Bosch dishwasher, but I wanted one with a fingerprint-resistant finish. That narrowed my selection to several manufacturers. This dishwasher has a food grinder in it. It gets my dishes spotlessly clean, and I have been very happy with it.

I am very dissatisfied with this washer (Maytag Washer Bravos XL), it doesnt use enough water to cover the clothes. No matter which cycle you use, the clothes dont come clean. Who cares about water sensing if your laundry isnt clean. I will not buy another water sensing machine, I think the consumer should make that call on how full to fill the washer. Even on power wash the small agitator turns slowly. Not happy with this machine at all.

I purchased a Maytag Dishwasher April 6th, 2011. Its only 3 years old and now the control panel isnt working properly. Specifically, the start button. Contacted Maytag Customer Care service and they could not help me other than charging $80.00 for the Maytag Man.. which by the way, we arent suppose to see because of their superb quality in appliances. So I have a repairman scheduled for next week. I am an highly dissatisfied customer because the dishwasher is used once a week for the 3 years Ive owned it. Just a poor quality product which I will never purchase again. Model #MDB7609AWB3 Serial # F10202246.

I have a Maytag Range that I bought new and installed 6-1/2 yrs ago for over $1200.00. I am single so I rarely use the ovens. The upper over I use maybe 1-2 times a month and the lower oven I may use once a month. The night of 3/7/2016, I used the cleaning cycle set on medium for both ovens. Yesterday, when I went to wipe the ovens down, I found the lower heating elements, on both ovens, had snapped. The top ovens lower bracket had broken in 2 places, the first break is about 2 from the connection, on the right side leaving about an 7 gap. The lower ovens element had broken in only one place about 2 from where it connects into the back of the oven. This has to be a flaw in the either the design or the material. In the 45 yrs that I have been using ovens and stoves, my last stove was over 35 yrs. old, I have never had a heating element break. While I can understand a break at the connection, I can see no reason that the it would break in the center of one side on both lower elements in the same oven. I also noticed that lower heating elements are a much small gauge than the top which I find strange.The other issue with the stove is the seals around the windows are not tight. I noticed dust was inside the two glass panes. The rubber seals were sunk down into the door, but Maytag said it was not their problem that I must have done something. When I remodeled my kitchen, I bought all Maytag products: 1.H20 Frig - The electronic panel went out after 3 months and had to be replaced. Manufacturing Defect - When the repairmen came to fix it, he told me to call Maytag which I did. They refused to pay for the repair because I called a repairman first, even though the business was Maytag certified. Even though I said I would cancel the service call they said because I had made the appt. and they recommended I call Maytag, they would not cover the repair. 2. Stainless Steel Dishwasher (Cost over $700.00) - Motor went out after 3 yrs. 3. Microwave/Convection Oven (above the stove)- Convection light out after 4 months. The replacements are not inexpensive.One other complaint I have is when I bought all my large kitchen appliance Maytag had a $600.00 rebate offer. Even though I mailed all the required documents to the company over 2 months before the rebate ended, I never received my rebate. The explanation I received was that the center that received my documents delayed forwarding them to the proper department that processed rebates and they were received after the offer ended. When I questioned the legality of the practice, I was told that this was all explained in the Terms and Conditions (ie: small print).

This is a dishwasher purchased at Home Depot on March 25, 2012 for a rental unit... call from tenant said the dishwasher did not work. Repair person from Appliance Hospital went out today and said the control panel is out and the touch pad. Cost is over $500 to replace. I will have to replace this dishwasher BUT NOT WITH ANOTHER MAYTAG.

We are a family of nine so I wash a lot of laundry. We bought this washing machine a month ago and hoped it would perform like our prior one. The problems are many. It is too smart for its own good- it requires a cleaning after every 30 washes but gives you zero warning beforehand so you will already have the clothes in and started the cycle when it will stop the cycle saying it needs cleaned. There is nothing you can do to override the cleaning cycle, so you are forced to remove your sopping wet clothes and run the cleaning cycle- wasting time and money on precious water! It also wants you to use its specialty affresh to clean it with, adding cost we hadnt planned on. Then you cant tell when to put the clothes in as it tells you to start the washer and then add the clothes, but if you put the clothes in first sometimes it wont start because it wont sense properly, and if you start it without the clothes. Then when you stop to add the clothes it wont start it with the clothes in it- which way does the machine want it?! So it is a guessing game as if the washing cycle will even start. And the washer wont hold as many clothes as our last one did. If there are too many clothes, the cycle will stop and it will refuse to wash until some are removed. Whenever there is a problem starting, which in one month has been four times now for us, it is a huge guessing game as to what is wrong for why it wont start. I dont need this kind of frustration! Further, the locking mechanism in the washer is plastic, and I know from experience that plastic parts will be the first to break. Had I realized this before purchasing, I would have looked for a metal locking device. My guess is when it does break, the whole washer will break. Also, from day one, it has made a sound that Im not sure is normal. It sounds almost like grinding gears every time each various phase starts or stops (washing, rinsing, draining, etc.). I sincerely hope this isnt a manufacturer defect as we didnt buy the extended warranty. We researched this model before buying and many were happy with it but I hate this washer! I loved my last Samsung washer but it rusted all over after just five and a half years even though it still worked great, so I didnt want to buy Samsung again so we took a chance with this Maytag. I am regretting this purchase. I consider myself to be a person easy to please. I want a washer that works that wont rust that you can put a ton of clothes in and throw it in the wash and forget about it. I dont want all this high-tech sensing stuff that just messes up and is highly inaccurate in what it senses! Why cant companies offer a simple, high quality product anymore that works, without the added costly features?! The model number is: MVW6230HW0. Avoid this model number.

I purchased a stainless steel (freezer bottom) Maytag refrigerator Model # MFI2670XEM0 in Oct 2012. Since then its been a nightmare. The repairman has been out four times, once being a week after I purchased it. It leaked and ruined my kitchen floor. Call Maytag, they didnt want to hear about it. As of this moment, I have three more things broken on the unit. My ice maker literally takes 3 days to make ice, the alarm on the door is broken, and the plastic crisper cracked and now will not stay in. Called Maytag again and they stated that they will not replace the item with one of equal value. They just keep repairing it. I will NEVER EVER buy another Maytag product again. I spent $1700 on this product and had faith in the Maytag product. That will never happen again. Shame on Maytag for not standing behind their products.

First the dishwasher - Control board no longer works. Seen many people with same problem. Dishwasher sitting there useless since cant afford to replace. Will cost as much as the purchase. Stove has defect between glass on oven door. Aqua clean feature is a farce and I feel vent at bottom of oven is asking for a disaster if any grease should spill in there. Maytag will not honor or admit any defects.

I bought my Maytag washer and dryer in Monroe County in Georgia, USA in 1980. Its a 1979 product and it STILL works perfectly fine after 40 years! Im 64 years old now and Im hoping Ill never have to buy a new set although I would love one because theyre so pretty these days.

I purchased a bottom freezer Maytag refrigerator two years ago. It recently began leaking water onto the floor from the freezer compartment. I just had it serviced and the serviceman told me that it was a common problem. The duck-billed check valve gets plugged. This is a problem with Maytag, Jenn-Air, Whirlpool, Amana, and KitchenAid refrigerators as they all share the same manufacturer. There is a service bulletin out on this that lists hundreds of model numbers affected by the problem (Technical Service Pointer #: W10632338). I think it is criminal that consumers are expected to pay hundreds of dollars to have this manufacturers defect repaired. I tried to find a place with the government to file a complaint, but wasnt clear who had jurisdiction. Perhaps a class action suit is in order. There have to be millions of consumers potentially facing this problem. Anyone with any knowledge of how to further pursue this defect, please comment.

Not only is the dryer junk, so is Maytag support and service. I have owned this dryer for 2 years; my previous dryers lasted about 20 years each. This one is on its 4th service call, none of which are apparently under warranty (well, except the first one). From what the techs who come out here tell me, the design and build are both poor. I will never own another one of these; if I can stretch it out one more year, then well replace it.For now, the drum wont turn. There is a nylon support bushing (and possibly more) that degrades immediately upon use. There are only two of us, with about 3-4 loads per week. This was supposed to be Commercial Technology. The only thing commercial about it is that you have to rely on commercial laundries to get the drying done. It is good that the drum has a 10 year warranty - it will make a nice planter out by the front gate.

My fiancee and I purchased a Maytag washing machine from our local Sears. We got it home and it worked fine, but after the first month it wasnt switching over from cycle to cycle. We called Sears and they stated that they didnt provide service to the washing machines, so we would have to call Maytag. We called Maytag and they sent servicemen from B & B Appliance to our home. We were told that they needed to order a piece and would be back at another time to fix the washing machine. They came back and said it was fixed. I went to start a load of laundry the following morning and the basement flooded. The hose had become dislodged when they were working on it. To add insult to injury, the washing machine was still broken. I called Maytag to request a different service company come to our home. Maytag said that they couldnt send a different company. They also couldnt replace our still broken washing machine and they could not accept a return. At this point we are out an almost $800 for the washing machine, over $5000 (which we have submitted to insurance) for the damage to our home, and almost $600 for a WORKING washing machine that was a different brand. We will never use Maytag ever again.

Maytag Bravos XL - I purchased my maytag washer & gas dryer on 5/12/12. In Dec 2012 the heating element went out. I had to wait a week for a repairman to come out on Dec. 20 to fix it. Now for the second time on Dec. 30th, 2014 the heating element has gone out. I called for a repairman to come out. I have to wait until Jan. 12th 2015 for service. I have 8 people in my home including 3 grandchildren. This length of waiting is ridiculous and very inconvenient.

Bought a new Maytag dishwasher in July 2013. In December it quit working and the problem was the control panel. The service tech knew automatically what the problem was when he arrived. It is now May 2014 and the control panel has gone out again. Contacted Maytag and was told they will extend the warranty another six months from the original warranty. After reading that this has been offered to others with mixed results I have my doubts on whether it will be honored. This is our last Maytag appliance.

I just bought my first home and after well over 20 years of apartment living and not having my own washer & dryer I was so excited to finally be able to buy one! I decided on the Maytag/Bravos and even spent the extra $100 for the glass top. The high efficiency machine was delivered on August 8, 2016. My kids are grown so its just me; I do one load a week give or take. A week or so ago, I noticed the washer was taking an inordinate amount of time to go from sensing to washing and even longer to get into the washing cycle. This past weekend, it didnt work at all. Just sat for hours with the sensing and washing lights on, without actually washing the clothes. The machine was packed loosely with the correct amount of High Efficiency Detergent in the proper place. I called the #Sears store I purchased the appliance from (Braintree Ma.) and they said there was nothing they could do as it was past 30 days, gave me their customer solutions number which is basically a call center with people who I could barely hear and/or understand. They in turn gave me more phone numbers which seemed to me to be in the same call center. I want to return the 4 month old washing machine that doesnt work and I want my money back. Ive filed a report with the Massachusetts Attorney General Consumer Affairs Department. I will NEVER AGAIN shop at #Sears and I will NEVER AGAIN purchase a #Maytag appliance. I am beyond disappointed in #Sears and #Maytag, both names that used to mean quality and customer service. And if theres a class action lawsuit to be filed, please count me in.

Purchased from Lowes October 2014, paid $680.00. Now needs $600.00 in repairs for new springs and basket rim according to a Maytag appliance repairman.Washer is leaking in the front left. Repairman thinks I need 4 new springs and a redesigned taller basket rim to keep the water from pouring out over it. Yes, it is 16 months old!! Ridiculous!

We purchased this washer 3/25/15 for $873.77, we also got the matching dryer, for the same amount. This washer, never washed good, it is simply a bad design, I dont know, what type of mind altering products the designer was on at the time, but it must of been some good stuff, since all brands jumped on the wagon. This is a POS, I have contacted Maytag, and they just ignore me. We need a class action lawsuit against them, they think they can take our money, and laugh at us.

Maytag MFD2561 - The metal piece between our French doors is also rusting. It is a design flaw. We also have a GE French door refrigerator and that piece on it is not metal!

I agree with everyone else on here. I would give this Maytag Neptune washer less than 1 star if I could. I also purchased this washer 5 years ago when I bought a new house. According to their commercials, the Maytag repairman is bored because their products are so great. I believe it is because the cost to fix their merchandise when it breaks costs so much.I had a 5-year warranty on my purchase and this washer started making this awful noise but the company wouldnt repair it because it was not broken. However, here I am less than 5 months later, and the bearings are so bad, the tube is scraping and falling apart and leaving plastic pieces in my clothes. I have a 3 year old I dont need plastic pieces in my clothes. You know my husband just left me and I do not have the money to spend on the repair ($500-700) nor have the money to spend on a new washer. Thanks Maytag for your great and wonderful service!

Let me make it simple for you, DO NOT PURCHASE A MAYTAG/WHIRLPOOL product. Maytag/Whirlpool believes its products should work for 1 year and then become obsolete, at least this is what the Maytag/Whirlpool customer service line told me. I purchased a MVWB950YW (Bravos XL) top loader on September 4th, 2012 for $948.00 plus $99.00 for an extended warranty. The washer worked marginally well when it was brand new. June 2014, the washer in spin mode started to sound like a freight train was about to run through my house. When I called for service the service company immediately signaled it was a bad bearing and offered me $500 to put towards a new or refurbished Maytag!!! They claimed if they were to repair the machine it would VOID the extended service contract?? I wanted the washer fixed, I did not want to spend more money to buy a new machine. I continued to use the machine as is, with the incredibly loud noise. June 2015, the same machine starts to leak water and is even louder. Again the company in charge of the service contract offers money for me to put towards a new or refurbished machine. Net is, Maytag/Whirlpool engineers its products based on its warranty - 1 year. Anything after that they view as an opportunity to steal more money from you and I the consumer. Do yourself a favor and NEVER purchase a Maytag/Whirlpool product. I would like to think American products are superior to its foreign counterparts, however Maytag/Whirlpool is not in this league. In my opinion, Maytag/Whirlpool has lost the privilege to call itself American and should no longer be allowed to do business in this country.

I bought your Maytag model MDB7749SBW1 dishwasher on May 22, 2013. We bought Maytag because of your reputation...not because of price. However, in September, 2014 (2 months out of warranty!!), the control panel stopped working. I called the 800 number and the best they could do is to extend the warranty for 6 months BUT only after we paid for repair and control board replacement. This is not cheap!!! We were furious. I looked if there were recalls on this model but there is not (should be). Anyway, after we paid for repairs and a new control panel put in ($160.00 +- for part itself), we were very cautious about touching anything on that dishwasher. YOU HAVE an issue with design and I can give you link after link of other customers who have expressed the same thing. So, here we are in 2017... About 2 months ago, we noticed the exact same symptoms with the control board.In fact the ONLY way we could start the dishwasher was to turn off the breaker, let it sit for 20 minutes - overnight and then turn back on and hit the start button. We lost all control over the settings. Only auto clean and delay 2 hours were working. Yesterday, I purchased yet another control board ($179 incl tax and shipping). I plan to install myself. If I could afford another dishwasher, I would do it and never buy Maytag again. Maytag really ought to be ashamed and if they were truly concerned they would offer these defective parts at a steep discount or better yet, recall. I plan on submitting something about this issue with any consumer group I can find. I guess the only way to spread the word and perhaps force a company to respond is to post on social media anymore. This is NOT a like.

We (husband and wife only - no kids) had our Maytag washer for 4.5 years and around year 3, the control panel would need to be reset by unplugging it and plugging it back in. That alone was an inconvenience. This time, the Control Loc light is lit and will not go out despite using all troubleshooting suggestions listed in the guide so the washer is not usable. 10 year warranty covers the drum. I say that is like getting a warranty on tires and when one goes flat, you are told it only covers the hubcap. I can only rate the unit as garbage. Model is 5500, front load. So much for Made in the USA.

If there was a zero star rating available, that is what I would select! We purchased this range along with a complete kitchen ensemble for a remodel of our kitchen in December of 2011. Within a few months of purchase the enamel finish started blistering, flaking and peeling. Upon contacting Whirlpool Corp about the problem through their online chatline, email, regular mail and phone, we were informed (quite rudely I might add) that Whirlpool does not warranty cosmetic deficiencies over 30 days after product purchase. This is American Quality?? Since this has occurred the retirement home we are building will have no Whirlpool Corp products in it which includes: Maytag, Whirlpool, KitchenAid, Amana, Jenn-Air, Brastemp, Consul, Bauknecht, Gladiator, or any of the product lineup from the Chinese company Hefei Sanyo which they are buying. The attached photos were taken in May of 2012 and since that time the product finish has only exponentially deteriorated.

Under a year old @MaytagBrand fridge stopped working and they couldnt get a repairman here for a week. I said this was unacceptable--we would lose hundreds of dollars in groceries and months of breast milk. They didnt care. I asked if they would reimburse me for a private repairman, they said no. Less than a year old. Friends, I implore you, never buy @MaytagBrand. This customer service is truly unacceptable.

Weve always bought Maytag, but this is our last time. The washer is just a piece of junk. It uses very little water and the agitator does not work. The clothes end up at the bottom in a ball. The water level is so low sometimes my clothes arent even wet. As I type this it has been stuck in the rinse cycle for 2 hours. It just keeps repeating. Maytag should have to replace everyone of the BRAVOS XL washers. I am no longer a loyal customer. I might as well go down to the river and beat my clothes on a rock. At least they would be cleaner. Shame on you Maytag!!!

Our brand new Maytag front loader has a optimum (LOL) soap dispenser that can supposedly wash several loads before refilling. BUT, the dispenser fills with water after one load and dilutes whatever soap is left! We talked to a authorized tech who said it was a poor design. That the unit wasnt sealed from water or it would be under vacuum. We called Maytag and they said something like, Um well it has sensors!! Did they explain how it would sense the diluted soap concentration? Nope. It should be replaced by MAYTAG! Knowing it is something that they sell that is defective. Right out of the gate!! The engineer should be fired, the quality department heads fired too!

Purchased Maytag dishwasher model # MDBH979SAM1 on February 8, 2014. 6 months in paint came off door. Added 5 year extended warranty on 4/21/2015. Dishwasher started not working properly on 9/24/2015. Hit one button but a different would light up until finally on 10/2/2015 it quit working. Called for service On 10/2/2015 10:30 pm no answer. Tried again on 10/3/15 same answer. Tried again on 10-5-15 finally answered and they called repairman. No answer but they gave me his number so I could call him if he didnt call. Finally called him and He told me he was busy and could not come repair my dishwasher. I called MaytagNed they said he would come. When I called he said he was not coming. He had truck trouble. 10-12-15 Called Maytag back and they said they would find another repairman. They would call me back. Into 2 weeks waiting on appointment. I will never buy Maytag again. It didnt clean dishes good when it did work!

I inherited this Maytag washer, so it has been around a very long time (I have had it for 18 years). It still runs quite well, has 3 levels of wash/rinse, 3 cycles to wash in. Both of us...me and the washer are still kickin together. Highly recommend Maytag.

Lid lock issue. 2 years old. I will never buy a Maytag, or any other Whirlpool brand for that matter. I am VERY disappointed. A service call will cost at least $200 dollars so why not just buy a new washer for that price. Also, I read that consumers should stay away from automatic water level washers. They never work right.

I have done widespread reading and realize that the front panel flashing and a clanging noise coming from the fridge, as well as it not cooling or freezing or the water dispenser not working, is a common issue. My extended warranty had run out, and as I rely on the fridge given Im insulin-diabetic and have meds to store, I phoned Maytag to see if they would help regarding the part. No joy. It means that as I cannot to pay a repairman hundreds of dollars to repair it, I have to order the HV board myself and will attempt to fix it. I am hugely disillusioned with Maytag and would never recommend it to anyone.

The dishwasher turns on of its own accord. Sometimes when you get too close to it, once in a while in the middle of the night, and most of the time when you latch the door. It does a great job cleaning the dishes, but to no avail because its always in the middle of a cycle when you need them.

I have been Maytag customers for 40+ years. I purchased a new Maytag washer and dryer at Home Depot last year. The paint is coming off and the top is starting to rust. We have had Maytag washers and dryers for as much as 17 years that did not rust. The reason we bought Maytag was quality. Rusting in one year is not quality. Please contact us ASAP. Home Depot said there was nothing they could do.

MTB2656DEB - Well my fridge is now about 12 years old and from the beginning it was horrible ice as always forming under freezer door. The cold cut draw broke 3 times with its cheap junkie plastic. I hated it from the beginning. I have owned a GE double door with ice maker for 26 years. Wish I had kept it.

The control panel of our Maytag dishwasher stopped working when it was approximately 14 months old. We repaired it ourselves by following a reset directions we found online (push rinse button 5 times and then the cancel button twice). Also we cut the power to reset. Im not sure which of those two tasks reset it, but it worked until last week - now 28 months old. We are not able to reset the panel using any information that we can find. In trying to find repair options, we discover that there are a lot of complaints about the Maytag dishwashers control panels not working within just a couple of years. In speaking with Maytag, they tell me theres a class action law suit for this problem - meaning they do realize there is an obvious problem with their control panels, but are not acknowledging they have any responsibility to repair it. The law suit only covers the cost of the part but not the labor. The labor can cost between $100 - at the lowest - and up. Our Maytag dishwasher model # is MDB8949SAM1. Also noteworthy, our Maytag clothes washer gave out at less than 5 years. Maytag is no longer the company we all thought they were. Additionally, their faulty machines are costing their customers a lot of extra money. Not exactly what I would call a company with good customer service or even any ethics. We will never buy Maytag again.

We had Maytag brand washer and dryers in the past. They worked for years and I was able to repair or replace switches and some parts on my own. The new Bravos XL is a very inferior machine, nothing but problems. The clothes have to be washed two or more times to make them clean. There is no agitator, so your clothes have only other clothes to scrub up against, and the spin cycle is just thumping and banging and thrashing around until you’re able to get in and rescue it from itself. Our older machines had tiny steel shot in the rim of the machine to keep it balanced. Don’t buy this machine ever!!!

I absolutely do not like the fact that you can’t choose what size load you have. The washer wants to do it for you but it is not very good at it. You have to fool the washer to get any kind of water level or just use the deep fill every time which is what I do in order to get the clothes clean! This defeats the whole purpose of trying to save water. Also there are too many settings. I mean we’re just washing clothes here not flying a jet. I personally would prefer dials instead of the digital instrument panel. So much easier.

7 years is all I got from these appliances. The Maytag Washer started making a horrible noise when washing then smoke and shut off. Dryer would not shut off. We have taken excellent care with these appliances servicing them as we had an extended warranty on both. They cost us over $600 for the washer and $589 for the dryer, a big rip off! I purchased them in hopes I would at least get 15-20 years of service as Maytag is to be one of the best. Do not purchase any products from this company, they also have sister companies. Make sure when you need an appliance, you ask who makes them.

MAYTAG BRAVOS WASHER - Biggest mistake I have ever made, like all the other complaints, washer does not clean the clothes. This washer and dryer are in our vacation home. Only used on weekends we are there, now the washer is broken, will not spin and UL light comes on, even with no clothes in it. DO NOT BUY!!! Like others have stated, we need to start a class action lawsuit against Maytag for fraud and knowingly selling junk.

Purchased a Maytag Dishwasher (Serial # P33706417) in Sep. 2013. In the beginning was working fine. After a year and a half started having problems pushing the button to start, not starting. Had to wait a few hours then hit it again and all the lights would light up and then it would start washing. Then when done, some lights stayed on and never went off. Then a month or 2 later, same problem but only a couple of lights would go on and when done 2 lights would blink continuously. After several months now, none of the lights are working and cant get dishwasher to start. Called a tech and he said the control board and the touchpad were not working. Would cost me over $400 plus shipping, etc. to for new. Very frustrated with Maytag, as we havent even gotten 2 years out of this dishwasher and the 1 year warranty has expired. DONT BUY A MAYTAG!!!

I purchased this oven about 6 months ago. This is my second Maytag oven which I had for 18 years. I am extremely disappointed in the quality of this oven. I did my homework and shopped around and chose another Maytag. First, the ignitor clicks and clicks but doesnt ignite. After 4-5 times I have to shut the oven off and restart it. But worse than that is the enamel on top. The quality is HORRIBLE. You cannot use anything but a soapy sponge to clean the top. With my last oven I was able to use anything (softscrub, ajax, the scrubber side of a sponge) and the top was shiny clean. My stove top is covered with scratches and is not even thoroughly clean. There are grease spots around the burners that if I scrub any harder Ill take the enamel off completely. Very, very poor quality. Will never buy another Maytag.

My husband and I purchase both Maytag Washer and Dryer 7 month ago 2017, because we have purchase Maytag washer before and were very happy with it. But this new Washer does not clean clothes at all, it is worthless. We will not purchase another Maytag Washer again.

The dishwasher would not start July 30 2015. Tried to get service around here and no shops could respond. Called Midsouth Distributors for circuit board. They did not have one but would order and gave me the part # W10595570 based on the Model # MDB7749SBW3. Hoping could find one quicker somewhere else. Ordered one overnight from Sears and planned to replace the board by myself. However, I noticed the flat wire with 14 wires in the ribbon cable had brown spots. From my experience in the electrical systems, I realized this must be shorting out the start signal to the dishwasher logic controller. Sure enough, after scraping this off with a sharp knife, I was able to start my dish washer.My previous MAYTAG lasted 20 years. I bought this one in February 2014 at Home Depot. The design for the electrical controls is obviously very poor as testified by so many angry owners. MAYTAG should be required to replace all these control panels with a improved design at their cost. I hope this obvious poor design of a part gets attention in the United States and ConsumerAffairs will help us. I have called 1-800-688-9900 and registered with MAYTAG a complaint about this poor design.

We purchased the Maytag MDB8959SAS0 dishwasher about 2.5 years ago. A couple of days ago, the lights on the control panel started blinking and beeping erratically. I contacted Maytag and they said the control board likely needs to be replaced to the tune of around $250, not including labor! We spent $800 on this dishwasher and it cant even last 3 years?? Ridiculous. The only other advice the service rep. had was that we should have bought the extended warranty. Gee, thanks. I guess with Maytag, you really DO need that extended warranty because their products are junk. I think I will just scrap this dishwasher and go with a Bosch. We also have a Maytag range that needed servicing after owning it for only 18 mos. And a Maytag dryer that needed servicing after a month (at least that was under warranty). I will NEVER buy a Maytag product again... they are complete junk.

Whirlpool owns Maytag and it appears that selling poorly made products is now their focus. When I purchased this Maytag 30 Gemini double oven range, I thought I was buying a superior product. Now, I am on my 3rd repair. When would it fail, on Christmas Eve morning when I am trying to prepare dinner for 20 people who are coming for dinner party. I paid too much for this piece of junk. From now on, I am buying from the scratch and dent sale because there are no quality appliances manufactured today. Buy cheap and it wont irritate you so much because no one especially Whirlpool owned companies focus on quality.

I purchased a Maytag gas range about five years ago. After about two months, I noticed that the paint on the burner grates was flaking off. I called the company and they told me it was cosmetic. I have since bought two sets of replacement grates. I call the newest ones my dress grates, which I put on the stove when I am having company. I use the damaged ones for everyday cooking. Last year, the panel flashed. It locks constantly. And often, the door would not open, unless we pulled the stove away from the wall, unplugged it, and that cleared the computer. So, after months of unsuccessful door openings, the handle finally fell off completely. And the door locks whenever the oven is turned on. You have to finish your cooking, press cancel, and wait until the oven cools off, and then it will unlock. I have tried pushing aluminum foil into the latch hole on the door but have not been successful. Sometimes I just put a spoon in the door to keep it ajar while cooking. This cant be energy efficient. Of course, it is out of warranty. I saw a similar complaint about the burner grates. Also, the paint has chipped in several places on the cook top and the disks are all chipped. I am never ever going to buy a Maytag product. Oh, by the way, I called a repairman. I paid $65 for him to tell me that to replace the lock mechanism and the door handle, it would be $400. I can buy a new stove for that, but not a Maytag.

We purchased a Maytag Top Load 5.4 cu ft efficiency washing machine. May 2019. It was making a funny noise already mid October and we had 8 parts replaced. After that it completely stopped working. We have been without a working washing machine for 2 months now. The technician has been to our house 4 times. When he came on Dec 31st to replace the mother board, that didnt solve the problem. He says the washing machine can not be repaired. We have been fighting with Maytag Canada and Lowes since the beginning of December. Neither company cares. We will never own another Maytag product. The company are crooks.

The control panel and the electronic control box had to be replaced after only two years of use. It cost almost as much as a new dishwasher (492 dollars). The model of the Maytag dishwasher is MDB77479SBM3. This dishwasher looks good from the outside and runs quite but the electronics are cheap and cant stand heat without melting. My wife and I are retired and only used this washer about twice per week. It looks good, cost 650 bucks and it is a pile of junk. No more Maytag in our house. We had this machine installed in July of 2014... It crapped out in July of 2016.

Dryer doesn’t wash all the clothes and the dryer doesn’t dry anything correctly. All, regardless of materials or size of load, comes out damp. Repairman’s excuse was that it’s a learning curve(?) and our dryer vent was the cause (which it wasn’t as we had it checked out and there was nothing in it) and that was it. Very disappointed in the washer and dryer and now the company where we bought them as it seems that we’re stuck with over $2K worth of equipment that doesn’t wash or dry well. We’re awaiting to speak with manager for a replacement of anything not Maytag. Not holding our breath and definitely not a happy customer.

The Maytag Maxima XL front load steam washer is awesome. Its reliable and does an amazing job. There are so many features and settings and it makes my life easier when it comes to doing laundry. My favorite feature is the allergen setting which gets rid of allergens in my fabrics.

Worst washing machine I have ever owned. Read all the other reviews and concur with them. We get pin sized holes all the time. Brand new shirts yesterday and they have black stains all over them - not the first time either. Inside of stainless steel tub looks clean. Where do the black marks come from? Last Maytag I will ever buy!!

Bought this because of the load capacity and it seemed like it would be a good purchase to help save on water. But worst mistake ever. The water level barely touches the clothes on top. It barely has any water whatsoever. All my dark colored clothes come out with residue. It’s disgusting and cleaning with Affresh does no good either. Very disappointed with the company.

I bought this Maytag refrigerator model MF 12269FRB00. It is not, user friendly, meaning that condiments and small bottles just dont fit conveniently in any space, The biggest issue is the ice maker. The ice maker shoots ice out on each and every attempt. Every time you want ice you are guaranteed to have ice shoot out of your glass on to the floor. I often challenge my guests to get ice without the cubes shooting out of the glass. No one has ever won. Dont buy this piece of crap, unless you find humor in having ice on your floor every time. Shout out to Grays Appliance in Melrose for selling crap! I will never buy from them or Maytag again. To the engineers who designed this product, you suck too!

After 6 months of use, I still HATE my Maytag washer. I will never buy Maytag again! The machine must be tricked into adding additional water to wash. It begins to agitate with very little water! Destroying my clothes! Also, I am having to hand wash all my underpants. They do not come out clean. If I could send it back, I would! Feel totally ripped off! I would give 0 stars, if I could!

I have a Maytag Performa washing machine (model no. PAVT234AWW) and called the Maytag parts department to order a plastic pulley for the main drive motor. I was told I would have to purchase the 189 dollar motor just to get the plastic pulley. After two days web searching and calling local appliance stores I found that Whirlpool who uses the same drive motor sells the pulley (part no. 21001108) for 9 dollars. The Whirlpool pulley is even made out of stronger plastic. I just wonder how many Maytag customers have had to purchase a drive motor like I was told I had to by Maytag just to fix a 9 dollar pulley. I got lucky and my problem was solved, but only because a local store happened to have this particular problem so frequently that they were able to help me out when Maytag should be the ones helping out their customers better. Thank you for your time.

Before you purchase a Maytag washing machine...from anywhere (I got mine at Home Depot), think again. This machine doesnt wash clothes, it doesnt rinse clothing. What it does is takes forever to fill up the tub then it doesnt even come close to filling it to where all the clothing is covered for rinsing or washing, then it just stops and sits there for a few minutes (??) and then it proceeds to empty the tub and youre supposed to feel like your clothes were cleaned.Not in a million years will your clothing get cleaned in a Maytag washing machine. Youve been warned...dont waste your money. Go to a used appliance shop, but the best one they have that does NOT have the Govt. regs built into it, and be happy you saved as much money and did NOT have to go through all the frustration and hassle everyone else has that bought a new Maytag washing machine.

Purchased a Maytag based on previous models that worked. Now when I do a load of wash, no matter how large or small, the clothes are still wet after the full spin cycle is finished. This has been going on for a few months. There are only two adults so the machine is not in constant use. We have had the machine 9 years and frankly would never buy Maytag again.

My Maytag Bravo washing machine is very basic and convenient. It was the first appliance I bought when I purchased my new home in September of 2019. it is commercial grade so I’m able to wash everything from towels to comforters to heavy coats. I like the clean lines of it and the knobs are easy to use and are perfect for my needs. It has wrinkle control, deep water wash, a variety of temperatures including tap, cold, cool, warm and hot. There is a fabric softener feature and an extra rinse. The push button Start is perfect and easy to use.

I purchased a Maytag Neptune 24” front load washer (MAH2400a) and 24” electric dryer (MDE2400AYW) on October 26, 2005 from Sears in Chesterfield, MO. In April 2011, the drum in the washer began to slush and grind. Water also began pooling around the machine. I called Sears and arranged for service repairman. Before he even looked inside the washer, the repairman wanted to give me a coupon for $50.00 off a new washing machine from Sears. After my insistence, he finally opened the washer and told me I needed a new drum. Because of the Sears repairman’s reluctance to look at the machine, I had another appliance repairman review it and was told that the water pumps for this model were defective. Any loose items the size of coins collected inside the pump and damaged it. I paid $340.00 to get the pump replaced. Ten months later, the dryer started smoking. After scheduling a service call, I was told the heating element burnt out and it would cost $360.00 to replace. It was then I noticed that the washer was leaking again. I took the front base cover off and saw mold growing under the machine. A little research uncovered that this set of machines has had many dangerous problems, from mold to catching on fire. There was a class action lawsuit filed and won by consumers in April 2005, yet I was sold this model in October 2005. I feel both Maytag and Sears knowingly sold me a defective and dangerous product. I would like to be refunded for this set.

Very dissatisfied with Maytag Washer Mod MVWB835DW0. This Large Capacity machine does not adequately clean a large capacity of clothes. In order to get a half decent wash performance from this machine, fill the machine only 1/4 full. Even using the recommended manual, I was very dissatisfied with the way my clothes looked after washing them with this machine. While I have been unhappy with the performance of this machine since purchasing it. What motivated me to leave this review is when my pants had the same sand debris on them after the wash as they had before the wash. I will be looking for a new machine this weekend. IT WILL HAVE AN AGITATOR TOWER!

Me and my wife bought a Maytag refrigerator from Home Depot. The top half freezes up in a big way and it gets real frosted up I have to pull it apart every 2 months to defrost it. The bottom half starts to get warm if I dont do that. I will not ever buy another Maytag refrigerator again.

We bought the Maytag Bravos XL washer 6 years ago when we moved into a new home. We have a large family and after reading many reviews, we settled on this washer. It has served us well for the past 6 years. At the moment, however, it is out of commission. The bearings wore out. My husband ordered new parts and we hope to have our washer up and running again in a couple of days.

Maytag calls peeling paint a cosmetic issue. With a convection oven it could be a toxicity issue. Waiting for an answer to my question as the fan blows the peeling paint onto anything that is not covered. Dont put foil on the bottom as this compromises the paint due to design. Truly sorry to have purchased Maytag as this line is not the Maytag we grew up with! Old school ovens and products had the quality or workmanship to last.

We have already replaced the motherboard and now it is throwing a code of and it takes a whole day to keep pressing start to get one load down. I hate these machines and tell everyone NOT to buy one. They are expensive to buy and too much trouble to fix or repair and too much money to fix. BUYER BEWARE!!!!