I bought a fridge, model number MBF1958, its a top fridge-bottom freezer. The freezer part leaked and spilled water that then froze onto the bottom of the freezer, which of course froze. I discovered this 1 month after the 1 year warranty ended. Maytag gave me a courtesy repair service guaranteed for 90 days. Of course, 2 weeks after the 90-day period ended, I have the same problem again.

Had a brand new Maytag MDB4949 dishwasher installed on 10/20/15. Noticed an acrid smell of burning plastic coming from the pull handle. After going to the reviews I see a pattern of shorting control panel boards melting the ribbon cable. Having repaired Xerox copy machines for 17 years, I recognized the smell of an electronics short and melting plastic. There are 600+ complaints for the same thing. Going to call the store we purchased it from and will escalate from there.

Bought this machine summer of 2018 when my old washer went out. This machine is impressive looking but that’s about it. Clothes don’t get clean. Half the time they don’t even get wet! I’ve had to wash sheets two or three times to get them clean and wet. When washing jeans there is always lint and white debris on them when the wash cycle is done. I’ve tried all different settings, I’ve tried different detergents always the same problem. Wish I’d never laid eyes on this model at Lowe’s last summer. Gotta say, worst purchase of an appliance I have ever made. Don’t waste your hard earned money on this piece of junk!

I also am the unfortunate owner of a Maytag dishwasher Quiet Series 300. I bought it in April 2006. The control panel has been a problem since the first year of operation. Typically, one of the indicator lights would randomly go on and off during the machines off mode. At other times, the control panel would not operate. However, if I waited a few hours, it would dry out, enough and then would operate. Apparently, steam leaks into the control panel and causes it to be erratic. This has been a problem with this design for many years and the Maytag Corporation has not cared enough about its customers to correct the design flaw. I remember when the name Maytag indicated a top of the line product. Sadly, this is no longer the case. As a result, my loyalty to them has ceased.I probably will not buy another Maytag product again. Their standards have eroded.

Most every post about Maytag/Whirlpool dishwashers reads the same. Mine is no different. The control panel on my model MDB7749SBM1 has failed after about 16 months of use. Its a lose-lose situation for the consumer, as the cost of parts and labor for the repair equals or eclipses the replacement cost of a new unit.Another fine example of the degradation of an American brand, once known for quality and reliability. Dont be fooled by the branding. Buyer beware!

We have had this washer for 1 year. I noticed right away my clothes would come out extremely wrinkled. Now not only are they wrinkled, they also smell musty. After researching I find others have the same issue, even finding a video of horrible mold under the drum. We called to have it serviced since we have a 5-year warranty. The service man recommended using Afresh. WELL, we do faithfully every month. He said they would not pay to have it cleaned, and even if he cleaned it, that the mold would come back. This to me is a major design flaw, one that could potentially make people sick. IF there is that much mold growing in the machine, with no way of cleaning it, and now the clothes are smelling, there is a HUGE issue!

This washer came with the home we recently purchased. I used the machine and OMG the spin cycle is NOT quiet.. I posted a video of it on FB. A friend of mine who owns and operates an appliance center watched it.. messaged me back and said Do not call repair man as it is cheaper to buy a new machine... I knew this machine sounded like a piece of **.. I know I wont replace with the same machine.

I am very pleased with the product, a perfect stove for cooking! It’s very easy to operate, easy to clean, multiple burners, excellent in cooking large meals, like soup, beef, Chicken and vegetable soup. It’s also very energy efficient, very safe to operate,

I have been trying to get my refrigerator repaired for over 5 months through the extended service plan I paid for. They sent out a service repairman. He could not repair the refrigerator without some parts so he ordered parts. We waited months to find out he can not get the part anymore that he ordered. So now Maytag Extended Plans and Service Power said they would have to replace the whole refrigerator but every time I call about it, they give me the runaround and say someone will be calling me back within 48 hours.I never get a call back. I give them a few days, then I call back and get the same runaround again. Im getting nowhere with these people. My refrigerator is a $6,500 refrigerator that Im sure they just dont want to replace or offer me anything for that matter. They should abide by the contract I have with them.

I bought my Maytag washer thinking that I was buying a quality product. My washer hardly ever can complete a spin cycle without bumping and knocking and then stopping. I have to babysit this washer because we never know if it will complete a cycle or not. The machine is totally level. We have to adjust almost every load just to wash clothes. Sorry Maytag but this washer is crap and I will never buy anything made by Maytag. What a waste of my money.

We purchased our Neptune washer and dryer combo MLG2000AWW from Circuit City in 1999 for $1900 also purchased the extended warranty. Here we are 15 years later and time to replace with new Samsung units. Besides having the main bearing replaced after 6 years in service, and having a sensor and a switch replaced on two separate occasions all covered by the warranty, our Neptune provided exceptional service throughout the 15 years. My understanding was that Maytag was bought out and run very poorly in the early 2000s as our unit was produced prior to that time... when Maytag was Maytag.

Purchased a new side by side American made Maytag refrigerator (Model: MSD2559XVEB ) in August 2010 from Best Buy. Just returned from a 3 week vacation and the refrigerator died shortly after we left on trip ( 14 months post purchase date ). $700 worth of food ruined.

Refrigerator (Model Mff2558vems) purchased end of November 2011. Early in 2013 notice refrigerator first forming ice all over freezer, including an ice sheet on bottom of freezer. Then noticed water around refrigerator. Called maytag and they sent repairman even though a little over year and out of warranty. Their service people seemed to know exactly what was causing the leak as they came in with the correct replacement part. Worked fine however, there was damage to my newly refinished hardwood floors which Maytag did pay to repair. A couple of days ago I opened the freezer and again noticed ice all over freezer. The next day, water all around freezer. I cleaned everything up, so I thought. The day after, we noticed the hardwood in kitchen buckling up far from refrigerator and the laminate in dining room bubbling, even though there was no visible sign of water. Called Maytag repair company but they couldnt come out for a couple of days. Called another local repair service familiar with Maytag refrigerators and he couldnt find anything wrong with refrigerator even though he knows leaking caused by refrigerator. Called insurance co. and they sent over service master. Leak is definitely coming from refrigerator. They had to pull up hardwood floor, part of walls, the dining room. They now have five large fans going and a defroster to dry things up. This is upsetting, as my daughters wedding is next month, my husband is currently laid off and I dont need this kind of aggravation again. I love the french door idea, so roomy for my large family, but I am now afraid of this refrigerator. I dont want it but think it is ridiculous I have to shell out more money when the refrigerator is less than 3 years old. I talked with a higher level supervisor at Maytag and they are only willing to give a 100.00 rebate towards a new refrigerator since the refrigerator is out of warranty. This is ridiculous. I thought by buying American I was helping our economy but what I got in return is heartache and crappy merchandise. If there is a lawsuit in California against Maytag about these refrigerators I want to join. My friend in N. CA who bought her Maytag refrigerator the same time I did is also experiencing leaking. So frustrating.

Here recently I got a bravos washer x series because it suppose to cut down water usage. Well that it did. Now going on 7 months of having it now its starting to act up like when the cycle is done it will lock again and repeat the cycle all over. I use the normal or powerwash cycle and here recently how its suppose to sense the load and then start spraying the clothes with water and detergent. Well not here. Lately it still senses and spins and then starts filling up like its on the bulky/sheet cycle but its on normal cycle and it doesnt fill all the way up - just 4 or 5 inches of water. So I dont know what is up with this piece of crap and why its acting this way. Other times it will work fine on the normal and the other cycles but now its just acting all crazy.

The Maytag range was purchased locally in 2012. The racks kept falling as the oven cavity warped in a convex making the rack supports too wide. The racks fell at the best position to cook a turkey. This could be dangerous when lifting something like a turkey or pie with filling! I was told that the oven cavity is NOT replaceable and I needed to purchase a new range! $1,600.00 plus taxes were spent just three years ago and now Im being told it cannot be repaired, no parts are available and needs to be replaced! Im sorry but I feel cheated and hurt because Maytag will not give any concession despite my pleading. What a dirty way to conduct business! No concession except an offer to cancel the service charges so far if I replaced it with another Maytag range from Delhi Radio Ltd. Are you serious?Why cant wider racks be provided for in these cases? Just what kind of engineer would compromise the thickness of a ranges oven cavity? Then build the range in such manner that the defective part is not available and cannot be replaced? Its a sad day for Maytag! Shame on you! Ive seen Maytag washers built in Newton last 35 years of hard family type washes! Whirlpool has purchased the name, stamped their own products with the Maytag name, and rested on the fine reputation of the name brand. Everything else is different! The Newton plant is in mothballs leaving hundreds of proud faithful employees stranded. Its a sad day for me and many others who were duped by a brand name and got something completely different.

Washer exactly 3 months old, will not work. Maytag can tell you nothing, they just want your money. They called a repair service in our area, never heard from them. Here we sit no way to wash clothes. And they say will charge to fix it. WHAT IS WRONG WITH THIS PICTURE. FO NOT BUT MAYTAG ANYTHING.

Maytag Front load washer mah8700aww - This washer has been the biggest boat anchor of a machine. Nothing but trouble and bad parts. New motor after 18 months, water level sensor at 2 years, main control board twice now at 2 years and 4 years, and now it is showing signs of needing yet another main board. E3 trouble code plagues our home and basement. This machine has been leveled and re-leveled numerous times and still shakes like crazy... I mix my paint cans by setting them on the top... the best use for this machine. Yes it sits on a concrete floor. So not satisfied and will not ever buy another Maytag anything. There should be a negative star rating. It does not deserve even 1 star after being taken advantage of like we and thousands of others have been.

Bought the Maytag model MFI2670XEM and within 6 weeks freezer wasnt making ice. Repairman came and fixed it, within a couple weeks same problem again. It was fixed and within a couple months same problem. Fixed, but makes very little ice. Now 18 months later after purchase freezer is leaking water onto the floor. Very disappointed!!! After reading other Maytag reviews I am worried I will have to dump this relatively new refrigerator and buy another (wont be a Maytag) and our upgraded dishwasher from Maytag is terrible! I hand wash all my dishes before putting them into the dishwasher. The smallest bit of ketchup or sauce is not washed away in the wash cycle. Our Maytag stove/oven seems to not heat correctly, as well. Internal temperature gauge reads 5-15 degrees off all the time. Thumbs down Maytag! Extremely disappointed with Maytag products! Will never buy again!

I really like my Maytag dishwasher. It has been very good. I have had it for at least 10 years and it is still working fine. It is worth every penny. If this one stop working I would buy another Maytag dishwasher.

Maytag Top-loading washer MVWP475EWO - I just want to comment on how engineers have made our washing machines worse instead of better. I had to replace my Whirlpool Cabrio washing machine - and did try a new one of that brand, but had the dealer take it back. It had so little water when it ran and was a piece of junk. Anyway, replaced it with the Maytag and it too has the water saving feature (which I understand all of them do) but I have to put it on the bulky setting all the time to even get the water to at least cover the clothes. The clothes just barely, if at all, actually move! They sort of rotate a little at a very slow speed. Boy, maybe this was the time to try a front loader so the clothes at least moved a little in the machine! I am so disappointed in how all the machines are manufactured now. One dealer told me I would like the Speed Queen, but it would take five weeks to get one. Thought this Maytag might do the trick, but now Im stuck with it anyway. It does not spin the clothes out nearly so well as my old Cabrio did. The clothes are pretty wet! So, another fine engineering feature. I wish the engineers would be the ones that actually did some laundry so they would see how bad the machines are. My daughter has three young boys and theres no way this would clean the clothes for her. I told her she should be glad her machine is still working. The dealer was very nice about it when I returned the other one, but it seems all the machines arent really made to clean clothes anymore.

We bought our Legacy Washer and Dryer from Home Depot in December, 2005. Luckily we also bought the one year warranty, because in January 2006, our washer quit running. We called Home Depot, we got the runaround and I think Maytag sent someone out. When he tipped the washing machine over, a belt was off. He said it happens. The next year, something else went wrong with the washing machine (not under warranty anymore) and I paid $129 for that visit. Three weeks ago, the spin dry quit doing a good job on the extended spin cycle. Tonight, I put a load of clothes in and though the washer sounded like it was agitating the clothes, when I lifted the top I saw it was just noise, no agitating. I cannot afford the service call, let alone the whole repair or a new washer.

Have had continual problems with Maytag Bravos. They will replace in under a 5 year warranty. If not for the warranty, I would be out over 700 dollars spent on this very bad machine. Based on my experience Maytag washers are of poor quality. I would stay away.

In 2013, $1850.00 I purchased a Maytag double oven, $700.00 Maytag dishwasher, and a Maytag refrigerator for $2200.00. I have had nothing but problems with all of them.... The oven locked up on me had to call a repairman to fix it. Ive had to replace the control panel on the dishwasher... And the refrigerator!! (WHAT A NIGHTMARE) In 2013 just received the appliance they had to install a heater in the ice maker because there was condensation. 2014, Refrigerator dead.. Repairman had to replace interface and control board.. 2017, Icemaker crashes and had to be replaced... 2020, Now here we are again Ice maker crashed again! (JUNK). My wife told me that she has had nothing but good luck with Maytag appliances... Never again.

Its a water saver model, so to really rinse the clothes of soap from the wash cycle you have to give it an extra rinse, which the machine has made available. So I do not know how much water it really saves.

I have the same problem noted by the other posts. Water leaking on hardwood floor from the bottom of the freezer. Refrig is out of warranty. Also, the deli drawer is also broken. This is a $2000 refrigerator and the quality is terrible. Please contact me for class action suit inclusion.

Last week I noticed that my freezer motor had a build up of frost. I melted it with a hair dryer. 2 days later there was a layer of frozen water on the bottom of my freezer as well as a layer of water on the first shelf in the fridge area. There is no way to access the drainage tube. I thought that the coils needed to be cleaned. That was not successful either since the coils run horizontal and only the front section can be vacuumed. Today, again the freezer motor area is frosted and layer of ice on bottom and the motor is making a terrible noise. How disappointing for a less than 2 year old fridge.

The oven hasn’t caused any issues. It’s beautiful stainless steel and black finish creates a shiny but modest finish to my kitchen. It’s self cleaning power is also useful and saves time and where I come from time is money. It cooks food evenly just as an oven should.

I have a Model MBF 1958XES4 which I bought from Home Depot in June of 2012. It has leaked repeatedly onto my wood floor. The water also collects and freezes on the floor of the freezer. I already have warped floor boards as a result. I just got it fixed. The repair person said he has done over 200 of these repairs in the last year. He also said Maytag knows its a defect and has supplied them with replacement parts. The company apparently tells its repair companies not to discuss this with their customers. I have yet to contact Maytag, although apparently from others experiences that will be futile. Im willing to join others in pursuing this. I had a 40 year old Kelvinator which was still working well which I replaced with this refrigerator when I redid my kitchen.

Our new washing machine (Maytag Maxima XTLM Front Load Steam Washer & Dryer w/ Pedestals) has developed a loud knocking while running which the authorized whirlpool repair provider said was due to internal ball bearings. He said that the washing machine caused the pedestal to become warped and the only way to stop the knocking was to replace the pedestal. Whirlpool refuses to replace the pedestal saying that the pedestal must have come that way or was installed incorrectly or was overloaded. There are only two of us and we never overloaded at all. The knocking started several months after the installation. If the pedestal was defective (came that way), why wont Whirlpool replace it under their warranty?

It takes almost a whole day to wash 1 load of clothes. The clothes dont get clean! The spin cycle wont let you spin. It runs your electric bill up! This is not a energy saver! I am so angry and disappointed! I thought Maytag was Supposed to be the best. Yall failed me. I wish I could get my money back!

Theres always a problem with this thing. It doesnt clean the clothes, its always off balance, and now it leaks from the bottom side of the machine in the clean washer cycle. Its only 2 1/2 years old. Should of listened to the guy who fixed my old machine. Dont get a Maytag!

We bought a Maytag dryer from Lowes on 4.23.20 for $567.87. From Day 1, it required us to dry even medium loads at least 2 times and sometimes even 3 times. I have been complaining to my husband since we got it. The clothes come out smelling almost burnt. But if you dry it once, the clothes are wet. And if you try to dry it the 2nd time for less time, its still not dry. So, it takes forever to do laundry. This morning, it sounded like a lot of metal was rattling around. So, I looked inside to see if change was in there, and nothing was in there but t-shirts and socks. It had been drying for less than a minute, but when I opened the door a wave of extreme heat hit my face. Now Im afraid to use it because I think it will eventually burn our house down. And with COVID-19, we do tons of laundry. We cant afford another dryer but may have no choice.

I sold my 20 year old Maytag set and upgraded to this Maytag Bravos washer. This machine takes almost 1 hour to do a load and they come out dirty. Only way to get clean is to set on bulky sheet which uses twice as much water as old machine. This unit should have never been put on the market.

I have a new HE (high efficiency) washer. It takes getting used to as its a definite change from the old agitating system but I think I like it. It doesnt make much in the way of suds but everything still comes out really clean. The wash cycle is much longer than my old washer but it uses a lot less water.

Maytag Neptune Washer Drum Bearings have once again failed. Last time, I replace the whole drum via diy, cost was about $160 for the part. Now I see that outer drum is $500 +/-. I just may only replace the Seals & Bearings this time OR just part this thing out and buy a real machine without the Maytag name.

I purchased my first Maytag dishwasher and it was recalled as being a fire hazard. I was offered to have it repaired or pay for an upgrade (approximately $200). I chose to pay and upgrade because I dont want a fire hazard in my home. After my paid replacement, I received a recall on the new dishwasher regarding the same issue (different model) and I chose once again to pay and upgrade (thinking that if I spent $700, I wouldnt have a problem). In less than two months of installation, the dishwasher died in the middle of a cycle. Filled with water, I bailed it out and called Maytag. I told them that I wanted a new one and they told me that I was past the replacement period. They sent a service man out and he stated that it was a problem with model # MDB7709AWB2 and serial # F03002958. He said that it was easy to fix and said he had done it several times. So now, within less than 1 month before my warranty is expired, the dishwasher did the same thing--it died in the middle of the cycle and wont turn on. I called Maytag and they told me that they would send out a third party repair company (JD Appliance) but I would have to wait for four days. I contacted Maytag and said that I was concerned about the dishwasher breaking down again for the same problem (bi metal unit blew). This is the second time it happened. Jeremy, the repair man, said that the first replacement was not installed properly and they should have replaced the entire unit. He stated that it was a common problem with that model, as did the first repairman in Dec 2010. When I spoke to a supervisor named Kia at 800-344-1274, she stated that they had no known issues with this model. I said that it was not what the repairman told me as well as the Maytag dispatcher. They both said that the heat sensor (Bi Metal Thermal Unit Part No. W10258275) goes up and has to be replaced because it is overly sensitive. If you are out of warranty, it costs around $200 to have it fixed. I told Kia and she said that it was not documented in her file, therefore, it never happened. I want to know my consumer rights to address this issue. I have paid for (on 3 occasions) a new dishwasher and have continuous issues that cost me money. I want an assurance like an extended warranty, free of charge, for the dishwasher that has already been repaired twice for the same exact problem. I have the original part that was improperly replaced to prove that it wasnt replaced to specifications, therefore, blowing it again. I was told by Kia that Maytag does not compensate or replace their products unless deemed not repairable by the technician. It doesnt matter how many time the same problem occurs. I would appreciate your attention to this matter.

We purchased a high-end stainless steel interior/exterior unit in January 15. It is now July 15 and we have not been able to get any use out of it. Day 1 washer leaked. Full day off for service. Guy told us we were using the wrong soap. It leaked on the very next wash. Called again. They forgot to check the soap dispenser. Another service/day off. Leaked again! Another service call/day off. They replace the dispenser & seal. Now washer no longer leaks but the dishes are dirty and wet even days later. Another service call. Another new part. And now we are waiting for our 5th service call. We paid for a new unit and have a refurbished cobbled together piece of junk. Maytag stubbornly refuse to replace this unit.

We had the same problem that everyone is complaining about re: frozen water in bottom of freezer dripping out onto floor. Swore when I got rid of the Maytag smooth top stove that broke after 5 years that I would never get another Maytag but broke down and bought this fridge. Maytag rep made it clear that the Fridge had a NOTE on file about the drain, but it was NOT a product recall. So after virtually taking the freezer apart before the repairman came, we ended up paying $120.00 for the repair, not the part. Yippee. Please note that the repairman told us we saved a lot of money by taking apart the freezer so most repairs probably cost a lot more than ours.

The washer does not get clothes clean at all even with the help of odor blaster, does not spin right, does not even out the clothes, walks while it is spinning. My towels do not smell good at all. The dryer gets too hot and the lint trap is always a mess even though I clean it after every use.

How many times do we have to go without a washer? We have to wait on service to check/see how many times it has to be fixed. This is since we bought it.

The Maytag Commercial Technology wash machine, the one with the clear top, leaves soap residue on our clothes. We have tried different detergents, always high efficiency, using the extra rinse, using the deep fill and nothing works. We have tried cleaning with vinegar and using the clean washer cycle. We had 2 technicians look at it, one tore the machine apart, both said nothing is wrong with the machine. So, we are left to believe that we are stuck with a machine the leaves soap residue on our clothes as Maytag will do nothing for us because of the assessments of the technicians.

Recently purchased a washer from Home Depot. Machine is now on its 3rd repair. The wiring harness is fired. Could have caused a fire. Now they still will not replace and part is on order which will take 4 weeks to be in stock. I called Maytag and expressed my concerns to which they could not help me as every washer is theirs can be repaired. I really don’t understand what happened to making things right. Very frustrated that they will not repair or reimburse for that matter. Please refund my mom and pick it up.

Bought it in 2013. Just replaced freezer motor. I thought for sure it would give me better service.

Seems a little ** one of a small child crawled into the washer and a sibling turned it on. We have been married 35 years and seen a lot of washers and this is by far the worst wash machine Ive ever seen. How would you rather do my wash in an old fashioned mangler? Very unsatisfied customer.

I purchased my Maytag Bravos XL washing machine in July 2016. In August 2016 it broke for the first time. I was just passed my 30 day moneyback guarantee, so Sears would not take the washer back. I have had more than 10 service calls on this washer in one year. I live in a rural area, so Maytag told me I was in a non-serviceable area and would have to wait WEEKS until they found a repair person willing to come to me. I only live 40 miles from Richmond VA, where I purchased the washing machine, so imagine my shock when they told me they couldnt fix it because of my location! Ive had countless people in and out of my house, and it still does not work right. You can only do very small loads, so the perk of having an XL machine is none. But even at that, it does not properly clean anything, tangles clothes, and will leave even the cleanest items looking terrible when they come out.Ive had a new circuit board, new transmission, new bearings and gears, new balancing rods, and still, Im left with a machine that does not wash and makes terrible grinding noises. I bought the washer and matching dryer as a set, and even the dryer had to get a new circuit board put in it in the 1st 60 days! After thousands of dollars in repairs on a $1000 washer, Maytag will not admit I have a defective machine and replace it! I just ran a load of laundry and have to call Maytag yet again, because the grinding noise gets louder with every run. Do not waste your money!I would give anything to have the 29 year old set I gave away when I bought this garbage back! I have literally been on the phone with Maytag in tears because it doesnt work properly, Ive had to throw away items that would not come clean because there is not a laundromat available in the town I live in. All I want is to be able to keep my family in clean clothing and linens, doesnt seem like too much to ask.

Purchased a new Maytag washer top load/Dryer set on April 1, 2016. Having trouble uploading receipt but I paid 1,145.83 for set. It took 2 weeks to get it delivered on April 15. 1st use it shook and wobbled even though the load was balanced but Ive read that is a problem with these machines. 1st load of clothes, washer didnt fill with enough water to wash properly - 3-4 inches of water for a full load of jeans. Top 2/3 of clothes hardly got wet! Changed the setting, same problem. Changed the setting again, same problem. I had to stand at washing machine and keep lifting the lid to get more water in the machine. Clothes didnt rotate in machine so all the clothes on top half didnt get cleaned. The spin cycle is scary! You could hear clunking noises and it had nothing to do with load being balanced. Did a small load and same thing with water level and spin cycle. Called Home Depot to pick up both machines on next business day. The dryer lint trap is so long, it made a mess trying to remove the lint even after only 1 load. NEVER AGAIN MAYTAG! Ive never regretted an appliance purchase like I do now. Maytag and April Fools day are a perfect match. Only its for real and not a joke.

I purchased the Maytag Atlantis Washer and dryer in 2004. I had the washer transmission replaced in 2006, I believe. For about a year now, the washer makes an awful screeching noise. I am not sure if its towards the end of the spin cycle or the rinse cycle, or both. In addition (and over the last 3-4 years), the dial sticks or stalls every delicate cycle. It will stop during the initial agitating and all you can hear is a ticking noise, in which you then have to manually give the dial a slight turn for the cycle to continue. It does it once on the light delicate and twice on the normal delicate. It really is a shame that Maytag is not acknowledging all of these problems as it is not feasible for most people to have a spare $1500 kicking around for a new washer and dryer every time they unfortunately buy a lemon. My previous washer and dryer were 25 years old and still working perfectly when I decided to part with them because they were fairly small. I dont even ever recall having any issues with either one of them in the whole 25 years that I had them. To see all of these complaints makes me more irritated with my appliances and my selection!

Currently own model MTB1504ARW, serial number 12541413GT refrigerator. The defrost thermostat broke and it is causing the device to frost over and not cool. Maytag is trying to replace the part with part number 63001051 and that part does not match the part that came with the machine. I spoke with a supervisor, Mr. ** who certainly was not a problem solver or any help, in other words, lacks customer service. I explained the installation of the wrong part may be dangerous and could cause a potential fire or hazard. He assured me this was the part available, but also said it was discontinued and I would have to find it with an outside vendor. I explained I compared the part removed and the part they are suggestion, per the part list, and its the wrong part. As a supervisor, Mr. ** failed to provide true customer service for myself and future customers who may be in the same situation, with the potential of causing a hazard for customers. The Maytag supervisor should learn to provide customer service and prevent possible hazards for customers, taking the next necessary steps or research the issue with other departments within Maytag. The parts below are evidence of the issue, the suggested part has two wires, the one from the refrigerator has three... poor customer service, at best with potential hazards to families and children. It may because their appliances dont break, according to their commercials, they just have too much time on their hands and cant provide the assistance that is needed.

I bought brand new Maytag appliances top of the line. I put the stove, dishwasher and refrigerator in and was waiting for the cabinets to be done before installing the microwave, It was a couple of years; I took the microwave out of the original box and had it installed and it made a terrible noise and then shut off. There is something loose or something. I called Maytag to activate my warranty but they said the time is up but I had never opened the box so I didnt know there was a time limit on sending it in. There was no customer service! The stove I bought for close to $2000 has had to have the control panel replaced 3 times so I have to pay every year for an extended warranty just to guarantee I have a stove. Last year I went through the holidays without one because it was out then too! I would never buy another Maytag again!

This is our 2nd Maytag washing machine in 25 years- we upgraded to a newer model though the old one was still working. The settings on the newer model are perfect for our family and we love all the options. We love our machine. Thanks.

Just after a year the bottom freezer began to build up frost. I had to thaw it every day. A repairman changed part and ran well for about 5 months when it started to frost up again. Again, I had to call a repairman in. $500.00 later, my fridge is working again. I am done with Maytag appliances. Never again!

We loved the YMMV4206 microwave - at first. After the warranty was over, we started having issues where we would put the food in the microwave and try to enter the time, wed get the message to open door and close door. Wed try that and for the next few months it would work. At the 18 month mark, thats all it would do, was tell us to open/close door. We ended up unplugging it and it has been unusable since before Christmas. When I call Maytag and related to the support staff our problem, they were of the attitude that it is out of warranty and we can send someone out to take a look at it - for $130 + HST without even repairing it, that would be to diagnose the problem that we already know, then we would have to wait for them to order the part and come back. Do Not Buy this product.

Maytag MBD7749SB - We purchased this dishwasher for close to $800 at Home Depot. After close to 1 year we had to replace control panel. After another 5 months we have to replace control panel again, but product warranty is only 1 year. Now we have to either buy new warranty for ~$250 or replace control panel for same amount. Customer service: terrible. We will not buy product from Maytag again.

This machine is the worst! I purchased this Maytag washer 2 years ago and the machine leaks from the left side bottom. I called Maytag and they said I need one of the techs out to check the machine and the cost was going to be $115 so I agreed even though was not too happy that there is no guarantee after 2 years. The service tech arrived. He could not move the machine himself and was a little angry so my wife called a neighbor to give the tech a hand after looking at the machine. He called if office to help him diagnose the unit and said the drum seal was bad and it would cost $315.00 so my wife agreed but at the end of the transaction my wife asked the technician, Is it guaranteed that this would fix it? He replied there is no guarantee but we still have to pay to try... What kind of diagnostic is this, Im very unhappy with this company. 1st the machine sucks after 2 years to start leaking and 2nd their service dept. sucks also... stay away from Maytag.

Our Maytag dryer is only, maybe, 3 years old. I do not dry towels, jeans or heavy sweatshirts in it (I line dry and then soften up in dryer). I clean the lint filter each time. Our heating element has gone for the second time. The first time it cost $200-250 to repair. It is so sad that our appliances are not made to last as they did. Or is it just Maytag? You can be sure we will not buy another Maytag item. I am looking into recalls at this time.

I got a new washer and dryer for my ex wife and son last August. Its October and the agitator broke off. She is not abusive to things and just the two of them dont produce much laundry. This was just poorly built. Maytag should be ashamed to have built such a poor product. I thought GE had the worst appliances, but Maytag must have hired their engineers. I have pictures and it has 10 year warranty right on the lid, lol. Should be 10 months,

Maytag Dishwasher MDB8959AWS6, S#F15006566 purchased 12/28/2011. Here is a record of the product repairs done by All Tech Appliance Service in Portland. 1/12/2014 - Thermal Fuse and Control Board. 10/15/2015 - Thermal Fuse. 9/2/2015 - Thermal Fuse. 12/5/2015 - Unit stopped working again, strong electrical smell, probably Thermal Fuse again. This dishwasher product has a design defect. It should be recalled.

We purchased a Maytag refrigerator with bottom freezer and French doors, in March of 2015, Model No. MFF2258DEM00. Its adjustable shelves and adjustable door bins were big points in its favor, at least in my eyes. So far both the fridge and freezer cool fine. The automatic ice maker was never connected, so we obviously have had no problems there. However, within a few months of purchase the bar that supports--and provides tracks for--the vegetable and fruit bins broke. It was replaced, but within another few months it had broken again.This is a DESIGN DEFECT that wont be remedied by replacing the item. The bar, which is plastic, hangs from a thin lip about 1/2 long by 1/8 thick. Thats way too flimsy to support the weight of one bin, much less two. There is no way to repair the bar. The entire assemblage needs to be redesigned and remade from sturdier material. Its not simply the inconvenience of having bins that dont operate smoothly. With their track broken, the bins rest on the glass top of the meat and cheese drawer--and threaten to break that. Theyve already caused the door to that drawer to crack.

I purchased my Maytag washing machine in June 2011 and within the first couple of uses, noticed that my clothes did not appear clean. I went back to Home Depot and complained and was told I had to use HE laundry detergent and I was. I gave it a while longer and still, nothing I washed ever seemed to come out clean. Sometimes, the fabric softener dispenser fills with water; other times the fabric softener remains in the dispenser. The machine makes very loud clunking noises during the wash cycle. I knew this machine was a lemon from the get-go. I should have insisted that Home Depot come take it away. I will never buy a Maytag appliance again! Maytag should have recalled this washer long ago and, if there was a Class Action law suit, I would surely join in!

The salesman tried to convince me to purchase a Bosch dishwasher, but I wanted one with a fingerprint-resistant finish. That narrowed my selection to several manufacturers. This dishwasher has a food grinder in it. It gets my dishes spotlessly clean, and I have been very happy with it.

I bought a Maytag refrigerator, model MBF 2256 KEQ2, two and a half years ago. Now the cooling coils are freezing up. I checked heater and thermostat for continuity and they were okay so the only thing left was the timer control circuit. On the earlier models, the timer control circuit is controlled by a Timer Motor or an Adaptive Defrost Timer which is separate from the main Electronic Control Board and much less expensive. On later models (including mine), the timer control circuit is incorporated into the main Electronic Control Board so if your automatic defrost quits working, more than likely you will have to replace the main board. I did not purchase an extended warranty because I believe they are useless from past experience. I bought the part on Amazon.com, received it in four days and replaced it myself for a cost of $78. This part costs $110 to $118 at Sears or a Maytag dealer.

I owned a Maytag Neptune washer and dryer for 13 years and never had a problem. The only one thing I would say about them is that since the washer had no agitator it would often tangle the clothes, but they were clean and not damaged so I was ok with that. We moved to another house in July 2016, and the moment we plugged in our dryer there was a spark and smoke under it. Our dryer was fried and it was because the previous owner put in the 220 outlet and wired it wrong. So our dryer was dead and cannot be fixed.Since the washer had the small problem with tangling clothes together, I convinced my husband to get a whole new set, not just a dryer. We went to Lowes and picked out a new Maytag Bravos XL, thinking that the brand was reliable and they were so big I didnt have to worry about doing bedding in it. Like ALL of the other reviews of this set, DO NOT BUY THEM! The washer does not use enough water to wet the entire load and you will be left with soap residue on your clothes and they will not smell fresh and clean at all. In fact, my son sometimes wets the bed or has dirty underwear and that is what my entire load of laundry will smell like when I wash them. Imagine taking a load of dressy work clothes out of your dryer and they smell like dirty underwear!I have tried other settings, different types of soap (liquid versus pod, etc) and doing smaller loads. None of this fixes the issue. It is obvious that Maytag and Lowes will do nothing about this issue, according to other reviewers, so Im not even going to bother to have them come out here to do a service call and charge me for it. So Im stuck with a $1,500 garbage laundry set! (Actually the dryer is fine, it just takes longer to dry than Im used to). Im all for a class action suit to get our money back and force them to stop producing such crappy products! Also, if you are considering this set, keep in mind that they have just over a 1-star average rating on this site, and that is because every reviewer is forced to add a rating of at least 1 star. If not, I think wed all pick the zero.

I bought this washing machine 2 years ago or so. We have always bought Maytag. My mother still has hers she bought over 25 years ago and it still looks and works great. So my wife wanted a new washing machine so I said were going to get another Maytag. Boy did I screw up. What a piece of ** junk. Sounds like its grinding gears all the time, so loud. I close the door in the wash room and I can still hear my investment on a Maytag grinding my nerves because I spent so much on a product of a brand Maytag that I thought would be around for a while. Do not buy a Maytag.

Bought a stove in May of 2014. In July of 2014 we noticed a 1x6 stain inside the glass of the oven door. I called Maytag and they stated only 30 day warranty on cosmetic flaws. I said this was not there when we bought it. They asked if anything had boiled over because if liquids get in the vents on the oven door it can get in between the glass. I stated no, only cleaned with Stainless steel clear. They stated most likely when I sprayed the door it ran down in between the glass. I said that is a flaw. They said, no the vents are there to allow heat out. I asked if they also were designed to let liquids inside the glass, they said no, I said design flaw. They will do nothing. I also pointed out that nowhere in the owners manual is there a reference to this possibly happening. Our sons in laws have a 3 year old LG stainless steel with vents and have never had this problem. Maytag will not stand behind their products even when they are the ones at fault. Buy a different brand.

I owned a Maytag Bravos top loading washer for 8 years, and I loved it. It caught on fire while washing a load. Thank God I was home or it could have burned my house down. Just wanted to post this somewhere to issue a warning.

I have the model with a smaller oven on top. I use it about 98% of the time so Im not wasting energy having to heat a larger oven space. I also like the fact that I can clean one oven. The larger oven is used when I cook turkeys. I can cook many dishes at a time, by using the smaller oven for dressing or cakes.

This is not my first Maytag. Bought this one in August 2017 from Home Depot. Now all it does is make a grinding sound. No lights. Not anything but noise. I bought one without all the digital because I thought that could be more problems. The only part that is digital is the start/pause button. I liked the idea of less water and no center. It balloons the clothes when it is finished spinning. Didnt start out that way. I use the right detergent and wash it every 30 days as it suggests. Cant afford to call a repairman on such a new washer.

Maytag top load 300 series washer - This is the worst washer I have owned! It does not wash items- especially sheets - without getting totally tangled up and twisted! I wish I had my old one back that lasted 20+ years. I will NEVER buy another.

I have had my washer and dryer for about 5 years. After a couple of years, I noticed my washer would fill and stop. When I go to put clothes in the dryer, it’s still filled with water... very inconvenient! I have to open and close it and then it continues. The dial doesnt work properly! The delicate cycle hardly works... that started after about a year. It just freezes up and stops. I have to open and close it. It does not rinse right, leaves a film on dark clothes, and I have to rinse again; I do not over fill it either. Sometimes it does smell a little mildew.The dryer knob does not work properly. I set my setting and pull the knob out, and it doesnt come on. I have to do it several times or change the setting or put it on 30 minutes only... very frustrating! I never had these problems with my Kenmores! I wish I did not switch brands. These things should work properly. I realize washers and dryers dont last like they used to, but come on! They also cost so much more than they used to. I wont do this again. I will do more research as to what is a good product. Too bad!

On March 2011, I purchased a Maytag dishwasher model #MDB7749AWB1. The dishwasher worked excellent for 16 months. One morning, with dishes loaded and ready to go, the start button would not light up. The other buttons did light up but that did me no good, I need the start button. A few days later, none of the buttons would light up. I found a repair person who said it would cost over $200.00 to make repairs. I refuse to put another penny with no guarantee that this new part would work. I will never ever buy another Maytag appliance. The last inexpensive, unknown manufacturers dishwasher lasted me 13 years. Do not waste your money on this thing.

Purchased a Maytag Bravos washer model MTW6700TQ ON 5/5/2008. Also purchased extended service agreement. This washing machine was only five years old when it started rusting on the top of the body where you load the clothes and fill the detergent. Not in a million years did I expect a washing machine to be rust-prone. Its a washing machine. The service contract doesnt cover dust, mold, rodent damage, and RUST (like rust is an external source). When I called Maytag they were not surprised. They said the life expectancy of their product could be as little as a year and a half. Regardless of the extended maintenance expense I now must throw this piece of junk away. NEVER BUY A MAYTAG. This time I am buying an LG.

I purchased a new Maytag dishwasher (model #MDB4651awb3) for $300, in December of 2009. Seven months later, the dishwasher refused to start. Some lights on the front panel would remain on, while others would not respond. The Maytag repairman made a house call and replaced the front control panel, and vent. After the repair, the dishwasher worked fine for nine months. Then, the same thing happened again. It refused to start with the same front panel light problem. I called Maytag, and since the machine was now past the one year warranty, they wanted $275 for an additional 1 year warranty, to repair the machine. Since I can buy a similar new machine for $25 more, and felt this was now an ongoing problem, (it would be the third panel in less than two years). I expected Maytag to offer more to take care of their lemon problem. Since they refused to reconcile the situation, they obviously no longer stand by their machines. I will no longer buy Maytag/ Whirlpool machines, and do not recommend them.

I would like to say that I purchased the Neptune washer & dryer for my parents back in 1998. Up to now, 23 May 2015, not once has either of the machines required service and have been functioning well for the past 17 years. This is a testament to the quality and workmanship that is Maytag. This week I have purchased the Maytag Maxima front loading washer & dryer for my home because of Maytags reputation.

At 10 months old, the compressor fails. It took one week to fix. Exactly two months later, the compressor fails again. This time, there are no compressors in stock per the manufacturer and the extended warranty folks. Ten days and counting. 90 degrees outside. No idea when they will be available. It’s time to walk this one year old to the curb and get a responsibly built one. I should have held on to my old one. DO NOT CONSIDER A MAYTAG refrigerator.

H.V. Board failure on Maytag model #MFI2568AES refrigerator. Whirlpool needs to step up their parts program. This refrigerator has been down for over 6 weeks and part will not arrive till 7/10/14. There is no excuse. The Maytag name is about as good as our country gone to H_ _ L in a hand basket. Consumers should not have a wait on parts or repairs that forces them to buy a new appliance when they spend $2500 and it only last a few years and try to contact them, they wont reply. I hope everyone who reads this considers LG, GE or SAMSUNG and not whirlpool excuses and JUNK.

I purchased Model #MGR7661XB (Gas Cooktop and Oven) in November 2009. From the very beginning, we realized it was a mistake and looking back, we should have sent it back.The finish, both on the stove as well as the burner racks (the removable grate that the pan sits on when cooking) has some sort of coating that instead of repelling grease and food seems instead to actually attract it. Any hot liquid or grease actually seems to melt into the finish and becomes impossible to remove. Essentially, our stove was ruined within the first week. We have even tried putting a scouring pad on a wooden spoon and scrub with as much force as we can muster - to no effect. Short of using a putty knife, and completely destroying the finish, I cant think of any way to resolve it.As for Self-Cleaning ... yeah, right. Use for entertainment purposes only. It doesnt clean at all.The latest issue is now the oven lights about 20% of the time. The broiler still works and we have discovered that we can trick the stove by allowing the broiler to heat up the stove to about 200 degrees first - then, when the oven is already hot, the oven part will ignite.Speaking of igniting ... from the beginning, this stove has the loudest ignition system I have ever heard. You can hear it ignite click/pop from two rooms away and the oven cycles on/off every 10 min. or so. It is very annoying.All I can say is, never again will I buy another Maytag. This was supposed to be the upgraded sealed burner model (which also is impossible to clean). This stove is only 4 years old but it was a mistake from the beginning. Like I said, I should have returned it after the first week.

My washer is less than 3 years old when I noticed the bleach dispenser has filled with water. I soaked the water out with a towel only to have it fill again the next time I washed. This in addition to the feeling I have that too much soap is left in clothes and spot removal is pretty consistently negligible.

I bought the Maytag Centennial Washer a year ago. I have had nothing but problems. The clothes never get fully wet so you have to wash clothes 2 or 3 times. The lid does not open when running. So you cant put soap after the clothes are damp. I say damp because they dont get wet. Right now the sensing light has been on for 2 hours. I need to catch a flight in the morning and I cannot wash my clothes! My white clothes never get clean. I have to wash 2 or 3 times. Actually 4 time would work better. The water and electric wasted with washing over and over again is nuts. Stay away. Ive warned you!

Bought a new Maxima washer in January. Worked for one week. Got error codes and electronics board shut down. Contract serviceman says board should have reset after turning off. Ordered new board and it is missing one of the electrical wire connector plugins. Maytag/Whirlpool is having a problem with these boards.Three weeks without a washer. Two days off work. When it goes out again, days off work will be close to what I paid for it. Thinking I may cut my future losses and buy another brand when in-transit board goes out.

I purchased my 10kg commercial Maytag dryer in March 2015 and started using it in May 2015. Within two months the heater had broken. I contacted the people I bought it off and it turned out I had to contact Whirlpool. It took them 8 weeks to get my dryer going again. The dryer broke down again in November. This time it was a sensor. Again I had to contact Whirlpool, it took them three weeks to get it going again. Being a care home the dryer is essential to our business. We were led to believe when we took out the extended warranty that the dryer would be fixed within a week. I will never purchase a Maytag again or anything to do with Whirlpool.

My Maytag washer has been a problem since we bought it. Maytag washer has been repaired 3 times. Stopped working again. I am 78 years old, I have take myclothes to the laundry mat. First, waiting for the repair then waiting for the parts. If Maytag stands by their product they should replace it.

The frontload washer 4000 series began making a very loud noise on spin. I called Maytag and requested service. The technician came and made a diagnostic evaluation, stating this has been a bearing defect affecting several of these models. I called Maytag, and the representative agreed to ship the parts at no charge. A week later, we received the parts, only for the technician to find one of the parts damaged in shipping perhaps. So another part was sent directly to the Maytag dealer. Upon my research, this appears to be a known issue with the Maytag/Whirlpool corporation, and I found where customers had requested Maytag to also be responsible for the service/labor costs, which were also covered by Maytag. I made the call today and was advised no and to be happy that Maytag paid for the parts due to a known defect and that no service or labor charges would be covered. I understand my machine is out of warranty, but this is a known defect; its nothing caused by my self.

I own a Maytag MDB9150AWB dishwasher which isnt covered under current recalls. Yesterday, I heard a loud pop sound, and it stopped working (also popped the circuit breaker). After taking the door apart, we found burnt wires at the bottom of the door close to where they bend to go under the dishwasher.I called Maytag to find out if they would do anything, since this seemed like a defect in the materials used. They wont offer anything!

Horrific, useless, inconsiderate, rude, discourteous, arrogant and banal! I bought a brand new washer and dryer. The dryer is steam type and defective and they will not exchange, despite never being used. Nowhere am I committed to an agreement saying that the machine will not be replaced if it is defective. I am getting the run-around from the store, the manufacturer and the service technicians that didnt even arrive with tools when they came to evaluate the problem. If I had my way, I would return the washer and dryer and change manufacturers. But it is a stacking unit and I used the washer which commits me to it! Maytag, Whirlpool, JennAir and KitchenAid are all the same company. I am running out of options except going to the European manufacturers! Miele will at least install the appliances. They will be my next machines and I will not have to pay a plumber twice to install them the next time!

I bought this dryer 3 years ago and the fuse has blown three times. The dryer gets really hot and blows a fuse. The entire back of the dryer is clean and free of lint, the hose on the back, and the ventilation pipe running out of the house are completely clear, but the dryer continues breaking down. The Whirlpool NC folks have been out here three times yet it has broken down once again. I should not have to purchase another dryer after only three years!

I wish I had seen these reviews before purchasing this machine. The plastic tub cracked and leaked all over laundry floor after only 30 loads. Part is unavailable. We will have to wait 3-6 weeks for a repair. Manufacturer will not agree to providing a new machine. Machine is only 3 months old.

I am writing this because I received an offer for a protection plan today in the mail. I purchased a Maytag dishwasher on from Home Depot. I had to have the control panel (motherboard) replaced a month after purchase to failed again approx. a year later. I still own this dishwasher (MDB7749SBB) but only used it off and on 2 of the first 10 year - have not used since. Well kids are in college and my next purchase will not be a Maytag. The wife and I lost all confidence in this product.

My first job was at Sears but went elsewhere to buy Maytag. I have had only 3 sets of washer/Dryer in 50 years. The set I have now are over 20 years old! I am looking at a Maytag refrigerator now.

I would never buy a Maytag dryer again. It has been serviced 3x since purchasing in 2010.

We bought a Maytag Dishwasher on March 16, 2013. Less than 10 months, we had repairman come in 5 times. First was soap scums left on the glasses after a wash. Then, the soap dispenser was leaking. Now the control panel is not working. We have to wait for a week for the parts to come in. Total length of time for hand washing dishes since we bought this dish washer is three weeks. They said they are not going to replace it until it cant not be repaired. What does that mean?? Please never ever buy Maytag dishwashers!!!!!

We have had our Maytag dishwasher for more than two years. Heres how it stacks up: Energy Star rated-Yes; Noise-Almost inaudible except when water runs; Length of Cycles-long except for quick wash 59 minutes; Interior design and loading - 10 out of 10. This is the easiest dishwasher to load and it holds an enormous amount of dishes of all sizes and shapes. Adjustable and removable racks-Yes both. Everything fits including my barbecue and oven racks! Amazing. Stainless interior-Yes including silverware rack. Cleaning- 10 out of 10. Even on a quick wash (59 min) cycle this dishwasher cleans everything! I run a longer cycle just to sanitize if we have sickness in the house. Otherwise it is 59 minutes to finish. Drying-Like most dishwashers this one is only so-so in the drying department, especially on the short cycle. Without plastic containers or utensils the machine dries more completely. However, the amount of moisture remaining after a quick or regular cycle is minimal. The water tends to pool on bottoms of glasses and plastics mostly. Easy to dry by laying a cloth across top rack. Dries in just a few minutes.My only suggestion to Maytag is to work on drying technology to make the machines more efficient and effective. However, that being said, I wouldnt trade this machine for any other. It has every feature I love and a 10-year warranty on parts as well! My machine cost around $600.00. It was neither the top nor the bottom of the line.

I purchased a new electric oven/stove, dishwasher and over the stove microwave. My dishwasher didn’t work from installation and it took Maytag over a month and half to repair. My oven door hasn’t worked properly since purchased and finally broke and I have been without an oven for two weeks waiting on repair. The customer service does not listen to you and seem to be completely unconcerned about your problem. I was told the item broken was a common stocked item and the repair would be quick but that was not true. The repairman told me they would have my parts in a week and would install them on a Monday. They have now scheduled my repair for Thursday. Over two weeks with no working oven. I will never purchase a Maytag appliance of any kind due to the terrible customer service.

We purchased the washer and dryer combo brand new from Lowe’s, had them delivered and hooked up together when we first purchased our house in the summer of 2016. 3 years later, both (expensive!!!) machines are having problems. The timer had to be replaced on the dryer, and the entire electrical panel on the washer has gone out and needs to be replaced. So disappointing. Model number MVWX655DW (washer), MEDX655DW (dryer).

Shame on Maytag! Customer Service is appalling! Paid 2500 for one of their top of the line refrigerator/freezer and had the repair people 5 times in one year. It was determined that it is a bad model number that Maytag wont recall but knows it is faulty. Started with ice build up in freezer making it sound like a plane taking off. It kept running trying to defrost (energy efficient-right). The repairman put in a request to have the product replaced based on symptoms and freezer being at 26 degrees. We had to wait five business days for Maytag to review it. I have a family and was having guests. They told me to buy a dorm refrigerator and they would send me a small credit towards it in 4 to 6 weeks. They finally agreed to replace the known faulty model, but I have to wait for the exchange team to contact me (2 weeks later). I keep calling and leaving messages but cant get the exchange team to even return my calls. I have my sons graduation this weekend and I dont have a freezer and my refrigerator is faulty with all my vegetables rotting within two days. It also took two days to originally get someone in management to call me back (even though it did no good - she cant help me). You cannot talk to management if you call customer service. They downright refuse! What a company!

Maytag Dishwasher MDB77495 - We bought this dishwasher September of 2013. April 2013 when you pressed the option I wanted the options auto clean, rinse only, steam sanitize and delay hours. The thing would work when pressing start but I have no idea what it is doing. The repair man replaced the board and all was good for a couple of months then it happened again. The board was replaced again and in two more months it failed again. The repair man told me that moisture was getting to the board and there was corrosion on the ribbon mentioned in another review here. He contacted Maytag both times and gave them my contact information but they never called me + they told him that they have never heard of this happening with this machine. We had a Maytag machine 8 years ago where the board actually melted but like an idiot decided to try them again. I will never buy a Maytag again.

I tried to open the door to put clothes in the dryer and got severely shocked by 220 volts. The dryer is only a couple of weeks old. The power cord wasnt crimped and it fell out of the diggings and electrified the entire dryer. I guess we were lucky it didnt burn our house down. I took pictures then I fixed it myself.

Just purchased/used the washer. One needs water to wash clothes. I added water to the machine just to get the clothes washed. How can this pass any reviews when it does not use enough water to clean a set of sheets? Not to mention rinsing. Does anyone wash clothes in the group that designed this machine?

I really liked my Maytag Bravo X washer. Until, at less than 2 years old, it started having issues. It all of a sudden starting sticking in the spin mode, then it wouldnt turn off even though the cycle was complete. I have to pull the plug out of the machine it to stop from continuously running. I was charged $104 to have a certified tech come out for 15 minutes and recalibrate it and it worked for another month. It started having that same problem again and now, I have learned I need a new control board, which costs over $200, plus labor, over $60. The Maytag service rep I spoke with was very pleasant when she told me she spoke with her supervisor and told me there was nothing they can. So now I dont like my pretty new machine at all, and have to decide if I should stick almost $300 into getting it fixed again, or buy a new washer, NOT A MAYTAG! As I voiced my complaint on the Maytag website I saw that there were many of the same complaints about the faulty control board and am wondering what does it take to get a recall?

I have not been satisfied with this Bravo washer since purchased 4 years ago. I have been holding back anger, hoping things would somehow improve. Clothes are never really cleaned, cant even fill washer with very many clothes because the washer goes off balance. It takes a lot longer to do laundry. Clothes spin so fast they are in knots when I put them in the dryer. I always have to iron clothes. Today, well today we have a leak coming from under the washer somewhere. So please tell me, what is the advantage to having a HE washer again? By the way, no warranty since its been 4 years. I will never buy another one.

Purchased washing machine, with insurance that was offered to me 9/17/10. May 2013, control panel went. June 2013, dial switch went. July 2014 washer motor drive & belt drive had to be replaced. August 2015 is broke again. Will never buy Maytag again.