Bought Maytag Dishwasher in 2/2012. 10/2015 dishwasher stopped working. My husband tried to replace the motherboard, however, dishwasher completely done. Called Maytag and they said they would send a repair company at their expense, however, repair service called to verify appointment and told us how much it would cost us! Maytag had no intention of paying the bill even after they said they would. Called Maytag back and said the other customer service person was incorrect. Now, buying another dishwasher only after 3.5 years.

Bought the Maytag MDSH969AWS1 in Dec. 2010, and it quit after 4 and 1/2 years. Ironically, replaced a perfectly good 20 year old GE model that ran great for this piece of junk. I tried to diagnose the problem: the washer fills, but when the cycle is supposed to start it just hums. Then you have to drain it. So I think the problem is the motor or capacitor. The parts are stupidly overpriced, and Im not even sure if that is the problem. It could also be the electronics board (Ive heard of the problems with these on this brand). So instead of risking wasted time and parts Im junking this, er, piece of junk. The stainless steel door was rusting on the bottom too. American made crap! Bought a fancy Samsung to replace it, and will NEVER buy Maytag again. Im old enough to recall the lonely Maytag repairman -- Itd give him a swift kick in the rear for being associated with such a shoddy brand. Maytag, its the Dodge-Jeep of appliances.

My husband and I bought a Maytag dishwasher, Stove and Fridge. We were very reluctant because at our prior home we had Maytag appliances and they kept going out. Against our better judgement when we moved into our new home we decided to go with Maytag once again. First the dishwasher front panel stopped working. We had it replaced and it cost over 250.00 with replacement part and labor. Not a week later went by when our Fridge went out, that cost us another 300.00 plus to fix. Keep in mind we had only had these appliances for about 14 months. Less than a year of replacing the dishwasher panel it has gone out again. This is very frustrating and expensive. I dont usually write comments, but felt the public needed to know that Maytag has poorly made appliances. I recommend you spend the extra couple of hundred bucks and buy the better brands and warranties. Thank you.

I am angry at my Maytag! It sprays water on clothes that is not enough to soak them or let the detergent to be dissolved especially for towels. Hopelessly, I Hand Wash my towels, rinse in tub then just put them in the machine to spin. BAD BAD :( :( Is it possible to increase the water amount?

Model MMV4205FZ3 microwave hood combination. No problems with open door signal yet. However, light over the stove burnt out. When removing, it exploded.No didnt unplug first. Previous microwave didnt have a problem with this. Instructions are useless. Didnt say to unplug and doesnt provide a model number for the bulb. Consequently, we have now purchased 5 different bulbs and they dont work. Tested socket and power is going to it. Rep at Ace Hardware said he had heard about this happening several times and provided what was to be the correct bulb -- didnt work.

My husband and I purchased a Maytag Neptune washer and dryer set back in early 2005. It was our very first major appliance purchase together as a young couple. We were talked into going with the Neptunes as it was considered one of the high end models at the time, and it came with a 10-year manufacturers warranty, which by itself was a major selling point for us. We have now had our Neptunes for a full decade and I am happy to report that we have not had one single problem with either the washer or dryer the entire time we have owned them. In fact, they are still going strong to this day. However, as it has been 10 years, it is now time for us to upgrade. We have purchased all new kitchen appliances within the past year and we decided that its now time to upgrade our washer and dryer as well and go with a steam set. We will most likely end up selling our Neptunes since we will have no use for them once we get our new set. They have served us extremely well over the last 10 years and we wouldnt hesitate to buy Maytag appliances in the future.

Maytag dishwasher #MDB 9750AWQ - I am now on the fourth control panel and in less than one year, the present one is starting to fail. The third one failed in less than a year also! I have read the reports of others and apparently, this is not just my dishwasher. Maytag owes its customers a recall of this inferior machine.

I have had a few dishwashers in the past, however this is the worst product I have ever purchased. After a couple of years in service I needed a new control panel which cost $200.00. The dishwasher defaults to heated dry and the exhaust for the dishwasher is right behind the copper electrical runs so it corrodes and fries the runs. The way I see it Whirlpool and Maytag saw a unique way to gouge its customers for parts. They also have a rope and plastic cable system that attaches to the door spring that continues to break cost $28.00 a piece, I have replaced two. Now I see that one of the pulley guides (plastic) is broken and split cost??? Here is another brilliant engineering feat, the door panel clips into the control panel so that when the door is pulled in a normal fashion it comes loose. If you buy this line of dishwasher (p.o.s) plan to work on it and buy parts on a constant basis. Here is my advice: buy one control panel, two cable systems, and a couple of cable pulleys or buy a cheap dishwasher as a replacement and save some money. Run from Maytag or its parent company Whirlpool - let the buyer beware.

We purchased the washer and dryer in June 2009. This past weekend, I noticed that the washer was leaking. The price to fix it is half of what a new machine will cost. I am very disappointed in Maytag. When I purchased the machines, I thought I was purchasing a quality product. Ive had paid much less for washers that last longer. Needless to say, I am shopping for another washer this week and it will not be a Maytag or Whirlpool. They are pieces of junk!

I own a MAYTAG BRAVOS XL* TOP-LOADING HIGH EFFICIENCY LOW-WATER WASHER. On 9/1/15, after reporting a problem, a service person arrived to assess the problem. His diagnosis led to a second visit on 9/8. On the second visit he replaced multiple parts, assuring us that the problem was fixed. When this proved to be false, we called for a third visit; this time a different person arrived. After disassembling the washer he found a large hole and another cracked area in the inner plastic portion of the tub. We made a fourth appointment for repairs, receiving assurances that it would be repaired at that time. I received an e-mail today (9/16/15) informing me that an additional 7 days would be required to arrange for delivery the required part. In the interim, my wife and I are forced to use a local coin operated laundry about every three days, totaling 7 visits at approximately $25 and 3 hours per visit before the next scheduled appointment. The compensation offered, 9 months extension of the existing warranty is woefully inadequate. I want the appliance replaced, as history has taught me that you are obviously unwilling or incapable of repairing it correctly in a timely manner. Additionally, I want the initial warranty that accompanies a new product extended to a full 3 years. We have paid out over $150 and wasted 18 to 21 hours of our time unnecessarily. I expect compensation for the funds spent as a direct result of the bungling, incompetence of your service staff. My questions are these: 1. Was the part defective prior to installation? 2. If so, why did the representative not notice it and refrain from installing a broken part? 3. Why was there no mention of the damage on the first visit? 4. If not, how did the damage occur? Did the service man damage it and fail to report it? 5. What caused the delay in obtaining the part? I have other questions, but will no longer spend any more time on this debacle. I cannot honestly say which is worse, their quality or their pathetic version of customer service.

The first washer my husband and I ever purchased was a somewhat cheap top loader but it worked very well for over 10 years. We decided to fall for a bargain sale at Home Depot and went with the HE Bravos model. We were told that it would save us money and work great! From day one weve had issues. It never really seemed to clean right. It gets thrown off balance if you have more than one bath towel in a load at a time. After an angry call to the company and a somewhat helpful customer service rep, I began washing every load at the deep clean heavily soiled cycle and then did an extra rinse to boot. So much for energy efficient. So, fast forward 4 years, I HATE this washer but cant justify a new one at this time. Now, it stops mid cycle and I have to unplug it then plug it back in and restart it. When this happens, there is an awful smell. Needless to say, well be buying a new washer within a week or 2 and you can bet your life, it will NOT be a Maytag.

Worst washing machine I have ever owned. Read all the other reviews and concur with them. We get pin sized holes all the time. Brand new shirts yesterday and they have black stains all over them - not the first time either. Inside of stainless steel tub looks clean. Where do the black marks come from? Last Maytag I will ever buy!!

Just like all the other reviews, 14 months after purchase and 2 months out of warranty the control panel on our Maytag Dishwasher stopped functioning. The “10 year warranty” is a joke a covers 3 things. We had model MDB4949SHX, $550 new.

PURCHASED WASHER FROM LOWES. IT STOPPED WORKING IN 2 WEEKS. CALLED MAYTAG FOR SERVICE. First repair service wanted to charge me. Next repair company Rawlings made 2 visits, looked at washer 1st visit said they had to order top latch. 2nd visit need circuit board. 3 weeks passed no latch, no circuit board, nor repair service. DO NOT BUY A MAYTAG WASHER.

My washing machine is a Maytag Ive been using for over 27 yrs. I love the older, top loading machines because I like to take certain items out after 5 or less minutes. I now live in an apartment & wont use their machines! Thinking about a stackable for my personal use. I am quite fanatic about laundry & do a lot of items by hand.

Im writing in reference to Model # MF12569YEM2. Bought this 3 years ago for close to 3k. Since then it forms a sheet of ice under the bottom freezer and leaks water onto the floor. It has ruined my hardwood floor and leaked through the floor to my basement and now need to re-sheetrock the ceiling. Its a bad design and should have been recalled because I see everyone else with this model is having the same issue.

I have been the latest victim in purchasing a Maytag Refrigerator. Something needs to be done about the defective products they are putting on the market. I received 9/7/13 (yesterday) a new Model FW: 555 Complaints and Reviews about Maytag Refrigerators bottom freezer refrigerator. After being plugged in for 3 hrs, the temp was 60 degrees.. After 8 hrs same and 24 hrs same. I lost everything because of the defect. I notified the store 3 hrs after purchasing it and because I had it delivered on a Saturday I have to wait till Monday to get this resolved. I want everyone to read before buying a Maytag product.

Purchased new about 3 years ago, doesnt clean, ties clothes in knots, leaves white spots from softener that doesnt get wet sometimes after cycle, some areas are still dry after untying. Now error code 51 keeps appearing, service man 4 times replaced rps sensor as directed, nothing changes. Need a chain to drag behind truck, no technical support from Maytag or whirlpool. Old ones of 20 years still worked good, gave to niece. Lucky her.

My freezer has been leaking from the bottom for a few months and now the icemaker has quit working as well. The refrigerator has been purchased less than two years ago. The warranty is expired. I will not fix this refrigerator, as it is a gigantic piece of junk. However I would like to be compensated by Maytag at least 1/3 of the price so I can have it removed from my house before it creates more damage to my floors and subfloors.

Theres nothing at all good about this machine. It is impossible to work with. Ive hated it since the day I got it. Dont buy it, ever, ever, ever. You cant put additional items in once its started, you cant adjust a load thats uneven and get it to complete a cycle, it takes forever to do one wash and it often rinses multiple times and theres no way to stop it. I HATE THIS MACHINE. HATE IT. LIKE ITS A PERSON. HATE. Is that clear enough?

This has to be the biggest joke in the world for the respected name of Maytag! The engineers that developed this worst-of-all machines on the market must have been circumcised with pinking shears. 80 minutes for a wash cycle? Even rapid wash takes an hour of slowly spinning and spinning ad nauseam with almost no water. The clothes sit in the same position even on the very brief agitation cycle... Nope, the clothes do not come out clean, although if you add bleach to the dispenser, since there is no water in the tank, the bleach does triple duty and rots the clothes. Is this masquerading as energy efficient when all of the cycles are an hour long, about? Unfortunately it takes water to clean clothes and the environ-lack-of-mentalists must have bribed Maytag to develop the worst washer on the planet. Absolutely!

I have a Maytag Range that I bought new and installed 6-1/2 yrs ago for over $1200.00. I am single so I rarely use the ovens. The upper over I use maybe 1-2 times a month and the lower oven I may use once a month. The night of 3/7/2016, I used the cleaning cycle set on medium for both ovens. Yesterday, when I went to wipe the ovens down, I found the lower heating elements, on both ovens, had snapped. The top ovens lower bracket had broken in 2 places, the first break is about 2 from the connection, on the right side leaving about an 7 gap. The lower ovens element had broken in only one place about 2 from where it connects into the back of the oven. This has to be a flaw in the either the design or the material. In the 45 yrs that I have been using ovens and stoves, my last stove was over 35 yrs. old, I have never had a heating element break. While I can understand a break at the connection, I can see no reason that the it would break in the center of one side on both lower elements in the same oven. I also noticed that lower heating elements are a much small gauge than the top which I find strange.The other issue with the stove is the seals around the windows are not tight. I noticed dust was inside the two glass panes. The rubber seals were sunk down into the door, but Maytag said it was not their problem that I must have done something. When I remodeled my kitchen, I bought all Maytag products: 1.H20 Frig - The electronic panel went out after 3 months and had to be replaced. Manufacturing Defect - When the repairmen came to fix it, he told me to call Maytag which I did. They refused to pay for the repair because I called a repairman first, even though the business was Maytag certified. Even though I said I would cancel the service call they said because I had made the appt. and they recommended I call Maytag, they would not cover the repair. 2. Stainless Steel Dishwasher (Cost over $700.00) - Motor went out after 3 yrs. 3. Microwave/Convection Oven (above the stove)- Convection light out after 4 months. The replacements are not inexpensive.One other complaint I have is when I bought all my large kitchen appliance Maytag had a $600.00 rebate offer. Even though I mailed all the required documents to the company over 2 months before the rebate ended, I never received my rebate. The explanation I received was that the center that received my documents delayed forwarding them to the proper department that processed rebates and they were received after the offer ended. When I questioned the legality of the practice, I was told that this was all explained in the Terms and Conditions (ie: small print).

One month after warranty we had our first issue which cost us $380. Kinda my fault I was told by repair guy... My bra underwire came out during wash and destroyed the part we had to replace. Then a year later during spin cycle it sounds like an airplane taking off for about 10 minutes. Its so loud we cant even hear our TV! So guessing its bearings gone bad now? Which is a very difficult part to replace. And pricey. So guessing a new washer is in our future. We previously owned a Maytag washer and had it for 15 years and it still worked fine, we just wanted to upgrade. Big mistake! I wouldnt wish this washer on my enemies. I think the repair guys sets it to mess up when they do this reset thingy. Lol. Cause within a month of the renewed warranty we purchased was expired is when the 2nd issue began. I think the older washer are better because all this newer technology stuff is crap!! My advice do not buy Maytag Bravos series washer unless youve got lots of cash for repairs!!

The washer that always needs repair! My first problem with my Maytag washer was that the sensor needed replacing (wont wash or spin). Since then I have had the sensor replaced and motor replaced. Today, I had to call for a service call, and was told that I have to wait over a week! Bad customer service!

On my 3rd circuit board for a MDB7749SBMO MODEL dish washer. The people at Maytag are people that wont even talk to you about it. How many people have to complain before theres a recall on a faulty ribbon cable.

I will never buy anything made by Maytag again. I just bought this washer 9 months ago and the sensor broke. The repairman said I have to pay $300 for the new part and it will take 3 weeks, then the repair told me many people have this same issue and he wanted to be honest that this always happens to these washers and my best bet is to buy new... I am so sad I saved for 4 months to buy a new washer and it was a bad decision. I have learned my lesson.

I bought a fridge from Home Depot. It was on sale and not a Maytag. Somehow they delivered a Maytag. I am over-the-top happy with my fridge. It keep things cold. It is roomy, It has separate temp controls for the freezer and fridge. The bright LED lighting is wonderful. It is energy efficient. It is easy to move around when I need to clean under it. It was delivered right away.

I bought a Maytag washer, dryer, and a dishwasher from Home Depot. It has only been a year and 1/2 and the washer has already broken down. Maytag wont help and neither will Home Depot. We are two elderly ladies (sisters) that used it once or twice a week. I feel we got ripped off. We cannot afford parts, labor, or a new washer. This product needs to be pulled. And Home Depot should not sell anything that is not a better quality. I trusted both companies and am sorry I did. Thanks.

Thinking that the Neptune fiasco was over, I happily bought into the sick company and got burnt 3 times for all 3 purchases. The Gemini range with dual ovens: the controller clock with all relays and electronic package is dying, leaving me with no ovens, or slow heating and an alarm in the middle of the night. Now, even the burners are not working properly. Junk at any price, and I paid $2,400. Not 5 years old and repaired several times under warranty; all were electrical failures.The fridge is another failure. Apparently the Freon is leaking out. It is unrepairable and it was typical of these from what the service guy said, not 5 years old. It was repaired once, leaking on floor. Apparently, it was a kinked drain hose. The dishwasher was one year old and it caught fire when the dial was turned while the machine was running. The 4th machine, an over the range microwave, is still running… although from day one it sucks so much power on the dedicated line that it dims the lights in the microwave as it starts up and each time, the magnetron energizes. I am just waiting for it to fail too. Can you say never and mean it? There was no goodwill offered. “So sad” and “too bad” is the common line. Nothing will last more than 5 years if you listen to sales people at Maytag - junk. There was no help from the corporate office. Nothing I can do for you. Junk, junk, junk.

I have a basic Maytag dishwasher circa 2012. Not sure of the model number. It works well, no fancy features but everything you really need is there. My only real complaint is that the heat dry cycle always seems to leave the dishes a little wet, but thats common enough for dishwashers. It cleans nicely and hasnt had any issues or breaks in 3+ years. Basic. Three wash cycles (light, normal, heavy); Extra rinse option, extra hot option, and heat dry or eco-dry (i.e. no dry). Nice big rinse aid dispenser. Its not that roomy inside. Id say the size is average. It looks nice - its white and unobtrusive. It works really well with Cascade dish pods. The bottom rack is kind of a pain if your plates are curved more than usual.

We purchased the Maytag MDB8959SAS0 dishwasher about 2.5 years ago. A couple of days ago, the lights on the control panel started blinking and beeping erratically. I contacted Maytag and they said the control board likely needs to be replaced to the tune of around $250, not including labor! We spent $800 on this dishwasher and it cant even last 3 years?? Ridiculous. The only other advice the service rep. had was that we should have bought the extended warranty. Gee, thanks. I guess with Maytag, you really DO need that extended warranty because their products are junk. I think I will just scrap this dishwasher and go with a Bosch. We also have a Maytag range that needed servicing after owning it for only 18 mos. And a Maytag dryer that needed servicing after a month (at least that was under warranty). I will NEVER buy a Maytag product again... they are complete junk.

This is March 18, 2021. I bought a Maytag washer, model MHW5630HW2, which is their high end front load washer, in early July, 2020. The machine worked fine except that out of an available 10 cycles, only two would run. The seller, which was Sears, replaced it as defective. The second machine runs all the cycles but, though leveled carefully, it rattles, screeches, walks across the floor and generally seems to be trying to tear itself apart. The repair service replaced the shock absorbers in this new machine, after a six week wait for parts. This did nothing to fix the problem. The repairman finally just said he doesnt know how to fix it. After many patient hours on the phone with Maytag, they have said I have no recourse. The machine is under warranty and I purchased, for an extra $350, a five year warranty. Both warranties are useless. Maytag refuses to stand behind their product. I live in a small town in New Mexico. There is only one repairman. He cant fix it. Sooo...if you live in a small town, or dont want to spend endless fruitless hours with repair people or on the phone with Maytag, who will ultimately tell you they just cant help you, DONT BUY THIS MACHINE.

My 16-month old dishwasher, which is not being used everyday, broke its control panel. Maytag will not fix it for free because they only back it for one year. This is a major appliance, shouldnt it last more than 16 months? The cost to repair is almost as much as a new dishwasher.

We purchased this washer 3/25/15 for $873.77, we also got the matching dryer, for the same amount. This washer, never washed good, it is simply a bad design, I dont know, what type of mind altering products the designer was on at the time, but it must of been some good stuff, since all brands jumped on the wagon. This is a POS, I have contacted Maytag, and they just ignore me. We need a class action lawsuit against them, they think they can take our money, and laugh at us.

We bought Maytag Dishwasher on October 9, 2019. Due to the installation difficulties we were not able to install and try it right away. Lowes warranty expired in 30 days, and the dishwasher is not cleaning the dishes. Even with the hand prewash of all of them-they come out dirty. I have to clean them after. The dishwasher is very weak. We contacted Maytag and were told that they can do nothing for us, only send technician (we have to pay $160 per visit). We can not return or replace it, the quality is very poor, so we will have just to buy a new dishwasher and lose 500$ for this product.

My double oven was purchased over 6 years ago. They have been served yearly and work fine. The only thing is the cleaning cycle which if used at the high temperature to clean can affect the oven temperature control. I don’t use this function anymore.

After 2 years and 1 month, the machine stopped spinning the clothes on any of the cycles. After attempting to use the spin cycle manually that stopped working. I called Maytag, my washer is out of warranty. After discussing the situation with knowledgeable appliance people, they said it is probably the motherboard. I know how expensive that is to repair and pay for a repairman to diagnosis the problem. I decided to purchase a new washer. Of course, it was not a Maytag. I read online all the people with same or similar problems left out of luck. This is an outrage and Maytag should not be allowed to get away with producing, selling and not standing behind the products. These machines should have been recalled and replaced with ones that are upstanding and will last for more than 2 years.

I have a Maytag microwave and stove in my condo kitchen. Both are about 4 years old. Ill never buy another Maytag appliance again. This stove had problems from day 1 and the support was dismal. I had [bought] an extended warranty, which covered nothing (I let it expire and didnt renew). The microwave handle came off in my hand a few months ago. I stuck it back on with gorilla glue. Now it is starting to shut itself off, as if it lost power then mysteriously turn itself back on. Im sure there will be a new microwave in my future and it wont be a Maytag.

We purchased a washer and dryer two years ago. The washer got louder and louder until we realized something was wrong and we called to get it fixed. Luckily, that was within the time of the warranty. The noise, however, began getting louder and louder within a very short time. Maytag refused to fix it again. Now, the washer sounds like a jet engine and wont drain the water at all.

Purchased Maytag dishwasher from Ft Knox Exchange in 2011, Model MDB6709AWW1; Serial # F04117463. Like most posts before me, the panel started failing after 2 years. Unit is now inoperative. I am attempting to fix myself using repair techniques Ive found online as I refuse to pay hundreds of dollars to repair this piece of junk. Will never buy Maytag again.

I have owned my Maytag Bravo Series less than a year. After 4 repair calls, I called again. The service department was rude and hung up on me. He accused me of destroying the washer on purpose. They are the worst company I have ever dealt with. DO NOT BUY Maytag products ever.

Maytag XL Washer - My new machine is awful as well. Black clothes are smeared with I dont know what... looks like dirt. The wrinkle cycle doesnt work and the bedding cycle forget. Wish I read reviews... silly me.

I have a Maytag Bravos XL and have white residue on all the clothes that get washed in this machine since I purchased it. I have always used HE Detergent and have followed all Maytags recommendations to reduce the white residue to no avail. I had to wash my clothes 5 times to get the residue off of my clothing and 4 of those were without any detergent and on all temperatures and wash cycles. Model # MVWB835DW.

I purchased a Maytag washer-dryer combo in late July 2014. It wasnt until early August that we actually used the washer. It worked fine the first day, but the next day it would no longer fill. After following all of the troubleshooting instructions, I called Maytag to schedule a repair. They said they would locate an authorized tech to make the repair. I called back the next day and was informed that there was no repairman in my area and they would contact a service that contacts local repair techs. A few days later I called back to learn that they still could not locate a repair tech. I live near the New Mexico/Arizona border, and asked if a service tech could travel from Tucson, Arizona and was told that they could not cross state lines and, at that point there was nothing else they could do. They claim that I live in a remote area, but I reside near a major US Interstate (I-10). I will be filing a complaint with the BBB and my states Attorney General. It is now late October and all of my efforts have been ignored. I am totally disgusted with Maytags customer service.

We purchased a new Maytag french door refrigerator and from day one had issues with the ice maker. After three replacements Maytag informed me that this was an inherent issues and no fix available. So we had a $2000+ refrigerator with a non-functioning ice maker. Our 20 year old Frigidaire continues to make ice with no issues. Then the control panel lights started blinking and evidently this is also a known problem and when I called Maytag to buy the part, they said SORRY we dont offer parts on our appliances over 6 years old. This is the worst piece of ** I have ever owned coupled with the lousiest customer service in the world. I will never buy another Maytag.

Bought this stove in 2011. 9 months ago I had a 300$ repair for fuses to two out of the five stove top burners. Several days ago the ovens were not lighting and I called for repair again. Well the ignition switch in the lower oven had a frayed wire from the factory which created an issue with the control panel. Today I was quoted 600$ to repair the ignition switch and the main control board. PARTS ONLY. I am not repairing this stove. Called Maytag due to the issue of a defective ignition switch wire and got nowhere. Very poor quality product.

We paid for a brand new washer and dryer from Maytag/Whirlpool. Right on the machines it has stamped in a metal plate 10 year warranty. So at 4 years when my washer started screeching and smoking I called for service. Yes, there had been a leak that burned out something in the engine and the bearings were shot etc etc. But they have been back 3 times. Each time they lack some part. I first called them on July 29, 2020. Today is October 13, 2020. They have still not got the washer repaired. I need to do wash every day. We are a family. We also have a senior in her 80s. And dogs. I need to do wash every day. So for weeks I went to the laundromat. That cost a fortune. Then a couple of weeks ago I impulse bought a new washing machine. A Samsung. On sale. Doesnt match the Maytag dryer. And the old washing machine got moved out to the garage. Its the pandemic. I cant keep going to the laundromat. What good is a warranty if Maytag/Whirlpool always has excuses for why they dont have parts. Its the motor. The very basis of the machine. It took them 2 weeks just to look for one. You wouldnt believe the excuses they make when we talk. But I am really unhappy with the way it all worked out. What good is a repaired machine 3 months later than I needed it. I had to buy a new machine. Why didnt they just tell me to do that on day 1 so I could avoid the laundromat. Why are they spending so much money to basically repair everything in that washer when they could have just bought me the new machine. When is a warranty not a warranty at all, but just a big lie?

I purchase this dryer not even a year ago. It is not performing right. I call customer support and they willing to try something to see the problem. I hope I don’t have to pay anything out my pocket.

My fridge and freezer got warm and compressor is not running. It is not even 8 years old. I replaced start relay and start capacitor. It cost me $75, from Maytag store. I worked two days the bam! It’s broke again. It’s a Maytag junk, now what? I have two kids in college. It will cost me $100 for a service call. Our food is ruined.

We purchased Maytag Dishwasher MDB5601AWW/46171101NP when we built our new home. In the last several months, water was leaking out onto the floor. We called Maytag and they told us there was a recall on the heater element and that they would send the part out. We made sure they knew the reason for our call--TO REPLACE THE GASKETS!. Maytag contacted a local authorized repair person. When they called to set up appointment, my husband reminded him about the gaskets. The guy showed up without gaskets, saying Maytag didnt put it on the order! We called Maytag to set up another service call. The guy showed up again today without the gaskets. We were told they had to be ordered and that he would have to come out again! Three service calls for one issue! Aside from this, the circuit board has never worked right. We push the correct buttons, but never know what kind of cycle we will get. We learned to live with it. Our bottom racks are melted as well as the sides of the dishwasher. Now that we know about the heater element being defective, this may be the cause of the bad gaskets and melted racks. It will cost almost $300 just to replace gaskets, and yes, we have to pay a service call for it when it could have been done in the first place. We called Maytag to complain and were told that replacing the gaskets always takes two service calls--one for diagnosis and the second to put in part. They said they dont take the customers word for it when we tell them whats wrong!

On June 5th, my husband turn off the water to the house since we were going to be away for 4 days. Unfortunately, it was not completely turned off. When we left, the washing machine was OFF, with the door slightly cracked open (to allow for circulation). When we returned, there was water all over in our upstairs, plus water had gone down the walls to the lower level. We could not figure out how the water got into the washer since it was turned off. The insurance company asked that we call a repairman to find out what was wrong. Fortunately for the repairman and us, the machine continued to go on and on after the Curtis had checked it out (it pumped out for him but not for us) and turned it OFF. It jumped from cycle to cycle after he had turned it off. Obviously the control board did its own thing. Be aware-- it can happen!!

Purchased a Maytag four door refrigerator and it leaks water all over the floor. Every few days I remove ice from the bottom of the freezer.

We purchased a Maytag Dishwasher Model #MDBTT60AWW3. Shortly after manufacturer warranty ran out, the control panel went out. Luckily we had purchased the extended warranty. The repair company came out and put a new control panel in it. Two months later, the control panel goes out again. The warranty firm sends out a different repair company. They replace the control panel again. This time it doesnt work. They replace some of the buttons as according to the repair person they arent registering the correct OHM reading. It works again. Yay!. A week later, its not working again. The repair company is coming back. This is really starting to get old. Between the multiple times it has broken down, waiting for the repair company to come out, diagnose the problem and order parts, we have been without a dishwasher for approx. 2 months the multiple times it has broken down. Im so fed up with this thing. I also will never ever buy another Maytag again. They need to have a major recall on these because of the terrible, terrible control panel. This isnt just me, its a lot of people.

I bought my Maytag in 2013. It worked fine at first but for the last year it isnt getting clothes clean. In fact, some look like theyve never been washed. I have to run the rinse cycle 2-3 times and they still seem somewhat soapy. The washer still leaves clothes drippy after running the spin cycle. It takes 2-3 hours to complete a small load. I wish I had my old Kenmore back. It worked fine for nearly 20 years!

I am 65 years old and for all of my life there has always been a Maytag washer and Dryer in our home. My great grandmother and great grandfather had a gasoline powered Maytag. My maternal grandmother had wringer-Maytag and my parents have always purchased Maytags. When I was on my own I purchased Maytags. In November of 2012 I purchased a Maytag Bravos XL washer and dryer. I had no reservations because it was Maytag. In October of this year (2017), the washer starting roaring and I had purchased an extended warranty. I called a reported this. A local appliance repair provider was sent out after I called the 800 number on the warranty agreement. I waited several days and finally called the repair provider and was told the parts needed were backordered. Time rocked on several weeks with no communication until I began calling both repair provider and warranty company. Still no washer repair. Ultimately, the resolution was not to repair or replace the washer, but to refund the purchase price and sales tax. The Home Depot salesman that sold us the washer and dryer, as well as the extended warranty coverage assured us that should either the washer or dryer fail it would be repaired or replaced, neither occurred. This left me without a washer for more than a month. Then finally I called the warranty company used by Home Depot and I was told a refund check would be sent for the washer, along with laundry reimbursement check. My difficulty with this is even though I got my money back on the washer and some of my expense on having the laundry and dry cleaning done elsewhere, it does address the issue. Simply, I see the Maytag commercials all the time and they are simply noise on TV now. I am still wondering how this could happen to a washing machine that had less than two and half years of use, never abused, cared for could fail in five years. I was used to having Maytags last decades with little or no repairs. Given the fact this machine was top of the line and well taken care of, I so very disappointed and not buy another Maytag of any kind again. By the way, I have a home in the country with a 27 year Maytag washer and 20 year old Maytag dryer that come from my home in town that Bravos XL dryer replaced. My research during all of this has led me to conclude this is not an isolated incident, but far larger problem with these washing machines. Why has there not been a recall on these inherently defective washers been issued. Where is the justice in this, even though the refund and small laundry reimbursement has been received it does not make any happier. I have lost my confidence in Maytag and I thought that could not happen with Maytag.

I bought a Maytag dishwasher Model MDB7749SBW3 from Home Depot 6/2014 and by December 2015, the touch panel was going crazy! Ive read a lot of reviews and this seems to be common for Maytags. It would cost me almost as much to have this machine repaired, with a service call and the cost of a new panel, as it did when I bought it. When talking to an appliance repairman, he informed me that Maytag and most all the major brands are now owned by Whirlpool and that they are basically junk--not meant to last more then 1-3 years! Where are the recalls and how do we get a recall started?

I purchased the top load Maytag Commercial Residential washer with an agitator last month. I wanted a basic washer with Hot/Warm/Cold settings, Delicate/Normal/Heavy Duty cycles, Small/Medium/Large loads. I paid over $800 for this washer and I cannot wash my whites or rags in hot water! The hot water setting dispenses hot water, then cold water, back and forth. The end result is cool water. Ive called Maytag, Ive been told that there is nothing that can be done about it, thats how theyre made to be considered HE. I asked them why they even put a hot or warm water setting on the washer.You have no control over the water level, all cycles except for normal run in a deep water setting (full drum of water), I dont know why delicates are in a deep water setting. I only wash a couple pieces of delicates together. I end up using a lot more water and detergent with this washer. I hope we dont have to conserve water in the next few years! So though this washer uses less hot water energy, it wastes a lot of water, my water bill goes up and my detergent is used up much quicker! I cannot add time to my wash cycle, (the actual washing/agitation cycle is very short - 10 minutes) it has to drain all of the water and re-start the cycle with more water! $800 is a lot of money for a washer that doesnt wash like my old cheap washer. The local store cant do anything about it and Maytag brushed me off.

I bought a Maytag washing machine, model number MHW6630HW2 in January 2021. It works fine on ordinary loads, but it cannot spin the water out of bulky items, not on any setting. I put my machine-washable winter coat in the washer and it left it full of water. I re-tried on 4 different settings, and though the washer spins, it cant spin out the water. I went to the Maytag support site. The sites said my model doesnt exist. The phone number for support does not allow you to get any support other than a service call. The Chat option doesnt give a lot of support either. They said that if I call for a service appointment and the service technician finds that the machine does do a spin cycle, then the appointment is not covered under warranty.

Front load washer. When load is done. Removing is one long string of clothes... Is a large load washer which I like. But you cannot add any items after you close the door. And you always forget something that needs washing.

First we design the cheapest, flimsiest drawer possible on the bottom of the stove. Then we mount it on cheap plastic guides on a flimsy metal track. What a joke! Listen, drawers have been around over 700 years. If you cant do better than that, you need to look for another line of work.

Home Depot is selling defective appliances manufactured by Whirlpool and refuses to provide a full refund. I purchased a Maytag washer and dryer from Home Depot in August of 2010.Washer broke in February of 2011. No parts available for repair, Whirlpool replaced washer after 4 weeks. This washer broke in July 2011. No parts are available for repair until August 17th.

My washer is great. It get the job done. Have no agitator so I can wash 2 comforters. I really like Maytag Heavy Duty. Can get the job done right the first time. Self clean itself also. Also it is a efficiency.

Purchased brand new MAYTAG fridge May 1, 2016 from Home Depot. First week after delivery the slide out freezer started creating frost all over and leaking on floor. There is no Maytag man! Home Depot said they dont have anything to do with Maytag warranty. Called Maytag and they sent out repairman from Diamond Factory Service. They ordered new gaskets for freezer (two weeks) while we clean up mess every other day. Gaskets arrive and are put on. Frost growing greater than before. Repairman comes out again and sees the freezer door and door jamb are not flush. He orders a new freezer door. Maytag does not stock them but has to make a new freezer door (8 weeks). We are chipping ice every other day from the freezer and cleaning up the floor.I call Maytag and want a new fridge in June. They dont give replacements. Have to wait for the new door. I took straight edge and line it up with fridge and its not flush. Must wait 4 more weeks for the new door. This has been the worst experience I have ever had with a new appliance and will never buy another Maytag or Whirlpool (they own Maytag) product again and would discourage anyone else. Also I would suggest buying from a dealer that backs up their products with their own warranty team not a chain like Home Depot.

We paid over $800 (more with installation) for this quality dishwasher. Within one year we began to experience problems with this unit. The top control panel easily becomes water logged causing the device to fail.

I have never had washing machine that caused this many headaches. The point of a machine is to save you time and energy washing by hand. When the cycle is over, the clothes are tightly spun together that we spend half an hour attempting to untie all the clothes that are woven together. The clothes come back to us in knots, or torn because of the rough nature this machine has created. I have never seen anything like this before and would gladly throw this piece of junk out. We are moving and it would create more headaches to deal with this at the moment. I read that the company had severe money problems and it was due to this very issue. I cant believe a company this well known would allow this to ever hit the market! To openly LIE to people and make money off a product that is faulty deserves the karma they get. Please stay away from this company and their rubbish machines they make and then sell. BUYER BEWARE!

Seven years ago when we bought a new house, we bought all new appliances, Maytag Washer and Dryer, because they were suppose to be extra good and sturdy, what a joke. For the past four or five years, I have had to replace the lock on the door of the washer, which means Im without a washer for a week. Since no one stocks the parts because it is such a joke, some repair places wont even consider repairing a Neptune. Seems like since the company stopped making them because of the problems they have, as a minimum they should replace all Neptune washers that have been sold with a reliable washer, front loading in the same price range. I will never buy another Maytag product and will be sure to tell everyone I know not to buy them either.

I have had this washer (Maytag Bravos) less than a year and it does not clean my familys clothes at all. I have had to throw away clothes that are stained and ruined because this washer does such a poor job of washing. For the cost of this appliance, I thought it would do an excellent job, only to be disappointed. I have owned other Maytag appliances without a problem. This one is a disaster and has turned me against Maytag.

I have a Maytag MEDC200XW3 model. Good price reliable and rugged. It washes all the way from my delicates to my husbands heavy fire protective clothing with no problems. Holds lots of clothes with no issues either!

The ceramic coating on the interior of the oven cavity in the top oven, which I use the most (may actually happen to the lower oven in time) has cracked in the exact pattern of the hidden element. When I spoke to the salesperson at the store, he wasnt surprised and said that it will eventually bubble and rust!!! Called customer service and was informed they consider this an aesthetic issue with no fix!!! They will not offer any remedy or compensation. Are you kidding me!!!

I have had it (Model MDB6000AWB) for a few years now. It had to have the door replaced per recall. This dishwasher does not wash dishes well at all; need to rewash many items after going through normal wash cycle. Also, all spokes are burning and falling off, along with pans getting burn marks. I am not sure how safe this is anymore. I am going to purchase another dishwasher, but not a Maytag!

I purchased this washer in 2010. It has broken 4 times since purchase for the same reason. I was told by the appliance repairperson (which Maytag referred me to last time it broke on 03-11-11) that the manufacturer does not replace the machine until after it has broken down a 4th time. Now, the warranty has expired (in 09-11), and it has broken down again for the same problem - water wont fill. Sherry at call center informed me my machine does not qualify for replacement. Then, she would not give me a number or contact info for corporate office so I could forward my complaint. This machine is only slightly over a year old. I have had nothing but problems with it. I want a new machine, or at least unlimited repairs for the recurring problem. And I should not have to pay for a warranty that costs almost as much as the machine itself when Ive already paid for the machine, and at least an equal amount to the cost of the washer in repair bills just to keep this lemon on the road. I want a number and a name for someone that will listen. I may be part of the shrinking middle class, but I am a customer, and I should be treated right. Please help me.

I write this as the repairman is fixing my Neptune washer. As with many other complaints, I was experiencing the awful mold smell with the only fix being leaving the washer door open when not in use. This works but for the past few years a switch on the front broke which means we have had to leave the top off the washer and rig it every time we used it. Sometimes it would work and sometimes an error code would show and I would have to just turn to spin and finish that way. At the same time in 2005, I purchased all Maytag appliances. First the microwave went out then the ice maker broke and is still broken, then the dishwasher went out and had to be replaced. Washer broke so basically the only thing that has had no issues is the oven and all happened just outside the five-year warranty. Never again will I buy Maytag.

I wish I had seen these reviews before purchasing this machine. The plastic tub cracked and leaked all over laundry floor after only 30 loads. Part is unavailable. We will have to wait 3-6 weeks for a repair. Manufacturer will not agree to providing a new machine. Machine is only 3 months old.

I have recently purchased a washing machine. Within the first week I was calling a repair person to fix it. I HATE this machine, and I dont think that its fair that I get stuck with it because of the way it was made. I have to constantly redo the load because it doesnt drain and rinse. When the load is done the clothes are still soaked. I dont understand how technology can go backwards when it comes to washing clothes. SOOO DISAPPOINTED!!!

We purchased a Maytag dishwasher MBD7749AWM on 03/15/12 from Home Depot. The control panel went out on 01/24/12 under warranty. The unit was down approximately 2 weeks waiting for parts and a second service call. Just six months later (approximately 08/05/12), the control panel failed again. Thinking that a trusted American, iconic industry leader such as Maytag would stand behind their product, I called for what I thought would be a covered repair. I explained to a supervisor that their panels have not made it 1 year in service. She assured me there were no out of the ordinary problems with the panels for my model dishwasher in one breath, then stated they were out of parts and on backorder for three weeks. Now the truth comes out, further telling me that the unit is out of warranty and nothing can be done short of sending out a repairman, that I would be responsible for parts and service. After further discussion, she reluctantly agreed to send me the part for free if I arrange the installation and told me that it was very simple to install. When the part finally showed up on my doorstep with no paperwork, it was wrong. When I called and complained for waiting 3 weeks for the wrong part because there was no quality control in their parts and shipping department, all they could do was say sorry. They told me just to keep the part they sent and they would send the correct part. I begged that they ship the correct part overnight and they adamantly stated that was not an option. Maytag stipulates their process only allows ground shipping from FedEx per their contract. Knowing I had no other option, I agreed and waited for 5-day ground. The part showed up 13 days later and delivered by USPS. Apparently, I was lied to again and the left hand has no idea what the right hand is doing. Apparently, Maytag/Whirlpool have an inadequate and poorly trained quality control system in place and their manufacturing and electronic divisions are surly lacking a strong management team needed to go in and clean house. Instead, the whole mess they have contributed to continues to haunt Maytag has continued to be made to believe its okay to produce subpar products while continuing the complete demises of a once trusted American, iconic industry leader all while living on the Lorals of twenty years past.Whirlpool would do itself and this country a huge service by just letting this brand die and thrown on the heaps of scrap steel headed for China where maybe they can copy and fix what they were not capable of.

Ive read a few reviews and would have to agree. This is the worse washer I have ever purchased. I agree clothes go in dirty and come out dirty. I have to hand wash clothes to get them clean and wont even mention how long it takes a white t shirt to start looking like it was placed in mud vs being placed in a washer. Called Maytag and they said I was loading it wrong even though I was loading it as suggested by the manual. Then they suggested it needed service. I think not after reading these reviews.The irony is that I had called for service on a front loader due to prolonged washing cycles, the repairman was as useful as this MayTag washer. Come to find out I replaced a perfectly functioning washer, intake screen on cold water needed to be cleaned, for this piece of useless metal. I guess since reading that Maytag doesnt value its customers by offering some type of consideration I will replace this piece of crap. Please dont buy the Bravo series. You will be sorry and you will never have whites white again.

I know that Maytag wants to conserve water by adding as little as possible... But when the damn machine puts hole in 5+ shirts Im not a happy homemaker!!! At first I thought it was the dryer so I had a repair come out and explain Im not the first person that complained of this issue. Its too late for me but Maytag needs to be aware that they are losing, what I thought to be, one of the top washers reputation.

Purchased a Maytag range with Aqualift technology in 2013 thinking it was a good brand and *happy* to find a new way to self-clean my oven. This turns out to be nothing but a joke and I am not *happy* with it. After following directions to the letter, there is some loosening of anything on the floor of the oven, but the sides and top are slowly being coated with more and more grease. Ive spent way too much time with my head in the oven trying to scrub stuff without using a heavy duty cleaner but feel I now need to resort to Easy Off as there is no other way to get it clean. I also dont understand why they tell you to remove the racks since there obviously isnt enough going on to even clean the oven... How would the racks be damaged? And now I believe there is a problem with the Dual Choice element where Im not able to turn the temperature down. Even turned back to the low setting, the pan cooks away like its on high. I have to keep turning it off and then back on in an attempt to find something similar to medium or low heat. Im so very disappointed in Maytag and feel this method of oven cleaning should never have been put on the market. Its a scam!

We had this washer 16 months. We bought it new from Home Depot. The clothes came out with spots on them, white residue and grease spots. This was ongoing for awhile. The bearings went out after 6 months. It was so loud now the water pump went out. I was told by Whirlpool (they bought out Maytag) that water pump is on back order and could take a couple of months!! To fix the bearings and the water pump was almost 700.00. A new washer is 1000.00. We junked it and had to buy a new washer GE. We are sick about this waste of money!!! What a piece of JUNK this Maytag Bravos XL is!! We need to have a class action suit and try to get something back. This is ridiculous and they arent taking responsibility. Whirlpool/Maytag are rip offs!!!!

This washer (Model# MVWB765FW1) will not wash your clothes. Its not designed to give enough water for washing. That means some clothes will still be dry after agitator cycle; seriously. Thank you Maytag for going green! The repairman will tell you the machine is working according to design. That is true but the machine is a fraud as a clothes washing machine. The weight of the clothes in the tub tells the computer how much water to apply; good luck with that. We learned that if we add a bucket and a half of water, the clothes will come clean. Do you want to do that? Maytag used to be a good name.

We got our Maytag dishwasher in 2011. Weve experienced a lot of the same problems other people have mentioned. Control Panel was the first thing to go out. Now it has a foul odor coming from it and it doesnt get the dishes clean. The heating coil has stopped working and is rusting. This dishwasher is junk and Im very disappointed. I will never buy Maytag again nor any company related to them.

We have a 2 year old Maytag washer and dryer. 10 year warranty may I add. Well, we get 2 frantic calls that say, “They heard an explosion and the bottom of the house is flooded.” An explosion so violent that it shook our 3 story house and sounded like a bomb went off. Our washer and dryer are on the main floor. When we get there we found the washer top was dented so bad that it dented the bottom of the dryer that sat on top of it - blew the dryer door open! Blew the front of the detergent compartment and blew the side apart! Scared my mother and father in law who lives downstairs and who is bound to a wheelchair! Not to mention the fact that it flooded the basement and ruined the ceiling and Maytag says they will replace the washer! Are you serious? Who wants another washer which may or may not explode! What about the damage to my house! This just happened a couple of hours ago! We are very ticked off and not happy with We will replace the washer! Bad, bad business. This is not where it ends! I want my house repaired and won’t settle for anything less! Shame on you Maytag for putting profit above quality! Consumers beware!

Bought it in 2013. Just replaced freezer motor. I thought for sure it would give me better service.

First of all how you wash a load of laundry with a cup full of water? I got this washer and dryer (XL Bravos) as a birthday gift from my husband. This is the worst washer Ive ever had. It takes forever to wash and the laundry is still dirty, it only has a cupful of water in it. Im so disappointed at Maytag for selling something like this. If anyone is doing a class act lawsuit please include me in.

The AquaLift Self-Cleaning is a very poor substitute for a normal high temperature Oven-Range. It gives as much work as an oven without any self-cleaning, as it does nothing to the sidewalls or the door. The minimum temperature is 170 Fahrenheit, too high to rise a dough.

Major issues with the Aqua Lift Range. Takes forever to preheat the oven, 15-20 minutes to reach 375 f- 400 f. Aqua clean cycle not efficient and does not clean at all. The stove top is impossible to select and keep the heat consistent. When adjusting the heat up or down when you slightly move the dial it overreacts. When moved the heat sways may more than selected. The fridge works well but the bottom drawer is way too flimsy and it wont last a long time as it will crack. This is our first purchase of Maytag appliances and it will be our last. Our old 10-year-old stove worked much better than this one. Sincerely, Russell ** & Linda **, e-mail= **

Chalk up another bad tub bearing. Washer around 4 years old. Repair man says $350 to $400 to fix. Also said sees it couple times a week. Said after Whirlpool bought Maytag quality nose dived. Maytag no longer top of line. Will never buy another Whirlpool or Maytag product. Just replaced control panel on dishwasher also. Amazon sells kit to repair washer. That should tell you how bad it is. Called Whirlpool to see if they had plans to do anything about this. No they dont. Stay away.

I have had to replace the control panel on my Maytag Dishwasher 2 times in the last 4 years I have owned it. I diagnosed the problem using the serviceman repair manual which is located on the kick plate or lower plate for panel of your dishwasher. This is not one of the dishwashers that is listed on the recall list, but it is on the dishwashers list that Maytag suggested that you buy to replace your dishwasher that is on the recall list. Model number mdbh9898awb3.

We purchased the washing machine (MVWB400VQO) on July 9, 2009. Now we must buy a new washing machine as this one is apparently beyond repair, or else the repair costs will far exceed what it would cost to purchase a new machine. We are completely disgusted with its failure, as we paid $822.36, with the delivery fee and the tax. We expected that this machine would last for years, but here we are, 42 months later, having to again invest in a washer. Now that we have a computer and are able to browse your performance reports, we wish we had been able to read them before, in which case we never ever would have bought it at all.Yesterday it spewed water all over our basement, flooding things that should not get wet, providing an atmosphere for encouragement of mold and rust. The motor is gone as the housing is cracked, which was caused by debris getting into it, something that we could not have known or prevented. This is very poor design by your company, in our opinion. We called some repairmen, all useless as apparently the whole machine would have had to be completely dismantled at a rate of $84.00 per hour, and he could not tell us how many hours that would take, to say nothing of finding a new motor for the thing.We will never again buy a Maytag product as they are expensive with a too-short shelf life and there’s nobody who cares when you need help for something that should not have happened at all. I understand Maytag is really not the good old dependable Maytag we used to know and love at all, but rather is now owned by the Whirlpool Corporation, whose products we will never purchase either.I know why that lovable old Maytag repairman we used to see on TV is retired. Its because he could no longer stand the quality (or lack thereof) of the appliances that you are now producing. He is probably home, hiding his head somewhere and hoping nobody will recognize him. And what, kind sirs, do you have to say about this? Thank you in advance for your prompt reply.

I have an MFD2560HEB refrigerator that I purchased 6 years ago. I paid a premium price for what I thought was a quality product. It has had issues with the ice maker from the beginning, yet I was always able to get it fixed with unplugging the unit for a while. The fan inside the unit stopped working last year. I took apart the entire inside to replace it, and now, 4 months later, the water is completely frozen. Unfortunately, I purchased a Maytag induction stove in May and less than a month later, it is not working either. Maytag quality is not! I asked if I could return the stove, but was told I had to let them fix it. Im still waiting to use my $2,000 stove!

My dog had to be on a special diet to recover from a stomach disorder. I placed 1/3 cup of dog food plus chicken broth and baby food in a bowl. I intended to heat it for seconds. Minutes later, my dog was whining and sneezing. I immediately returned to the kitchen to find the food and bowl were completely charred. The biggest problem however was from the plastic splash guard that melted down. Smoke filled my home. I had to call the fire department. I was coughing and had difficulty breathing. The smell was horrible!The insurance company and I have had thousands of money in restoration cost due to the damage. I was out of my house for weeks and got very sick due to returning to the home that was not remediated properly (allergies and asthma). The microwave was an over the range Maytag MMV4205BA. I would like to find out if the fire was due to a malfunction in the microwave oven. If so, Maytag should be paying for the damages. I still need living room furniture and carpeting replaced due to smoke damage.

Actually, I have had my Maytag washer and dryer for 20 years so they are not new but I am thankful for this set because of the workload it does for me. I sometimes wash heavy loads (blankets, bedspreads, small area rugs), and this pair performs superbly. My son wanted to buy me a new set for Christmas last year but I definitely said no. I truly am happy that I bought Maytag and I truly believe that the Maytag repairman is a bit lonely.

We purchased a new Maytag Bravo washer and dryer on March 4, 2011. On January 26, 2015, our washer stopped spinning the clothes. We purchased these appliances while preparing for retirement, thinking we would possibly never have to purchase them again. There is only two of us! Wrote to Maytag (when it was still Maytag) and got a response of So sorry **, we can fix your washer for $319.00. We could buy a new washer for not much more than that!!!!!

I own an iron in case a guest needs to use it but I seriously havent ironed in over 20 years. I moved into a home in November and the appliances stayed with the home. I am systematically destroying my clothes that I always washed and dried but NEVER IRONED. They come out of the Maytag washer already wrinkled. I try to unwrinkle them in the dryer. I took 2 items to the dry cleaners to see if they could steam them but no results yet. What gives Maytag???

My Maytag refrigerator, french door freezer on bottom MFT2976AEMOO has had problems since I bought it. It is with the icemaker in the refrigerator door and freezer. My icemaker has been leaking since we have gotten it dripping water into the refrigerator. The freezer now is not working and all my frozen food thawed out. I am so tired of having workmen coming out to try to repair it. They even took the refrigerator back to the shop and had it for 3 weeks and said it was repaired and told me it was working fine. NOT frozen food, again thawed.

I have a 6-month-old top load Bravo Washer. It has destroyed two bottom fitted king size sheets and 2 shirts that now have holes. It apparently slices the sheets during agitation. I have a service policy and called the service agency. The technician said there was nothing wrong with the machine, yet it literally ate 2 more items. Help! I need a solution to this problem.

Same as everyone else, ice freezes up on the bottom and water runs out all over the floor, ruining my new floor. Whole kitchen was new including all appliances. Maytag is ruining my floors. Can find no drain pipes so not sure where the water is supposed to do. I think they forgot to install one. But I am getting pretty sick of seeing my floors ruined and stepping in water.

This washer is a piece of expensive junk. It was used sparingly (2 people using it) for 16 months when a repair service had to be called. The estimate to fix the machine ($980) exceeded the initial cost. It did not clean the clothes adequately when it was working. There was a powdery substance on the clothes when they were removed. The clothes were always bunched up and intertwined. Only the proper type and amount of soap was used. I cant recommend this washer to anyone. We were very disappointed since we have always purchased Maytag washers/dryers. Never again.

We purchased a Maytag Jetclean Plus Dishwasher in June 2013. It worked well enough initially. We bought it because it had a large capacity and built in disposal. By August 2014, just after the warranty expired, the front panel gave out. To have someone even look at it cost $150. By following instructions from internet discussion groups by other people facing similar issues, we were able to get it to run in random mode. Programs were no longer indicated or selectable but dishes generally still got cleaned. Two months later a wheel fell off the premium rack glides. Finally after about 2 years of use, the dishwasher finally gave up altogether. At this point the stainless steel tub is no longer stainless. The entire device has worn poorly and looks shoddily made. This is the worst use of $900 I have ever made, and what tweaks me the most is Maytags attitude and their ludicrous warranty that barely lasts out the weakest link in the device.

We trusted the Maytag name to give us a good product that would last. After six weeks the Maytag Bravo stopped working. Having to wait 7 days before a service repair person came to our home. The main motherboard needs replaced. So currently, we are still waiting for the part to arrive and have it installed. 2 weeks without a washer after spending 600.00 for a new washer. There is more problems also, this machine takes 1 hour to complete a single load of laundry. Plus it does not get the clothes clean and the rinse cycle does not get all the soap out of the clothes. Very unhappy with the Maytag Commercial Bravo. Will not buy another Maytag product. Save your money and get another brand. We plan to get this one fix and sell it.