I purchased my Maytag 4 door refrigerator with the freezer at the bottom (model #MFX2570AEM) in December of 2012. A couple months ago it started leaking small amounts of water. I now notice that there is such a build-up of ice under the freezer drawer that it wont even close properly. I, like all the other consumers that have complained am fuming mad. I purchased the Maytag brand because of its great reputation for quality products. However, this is totally unacceptable that I should be having issues with this refrigerator less than 3 years later. Shame on you, Maytag!!!

During 2018 we purchased Maytag Bravos top loader to replace antique KitchenAid. Very dissatisfied at first, but luckily found the settings that makes my machine work very well on every cycle. First add 1/2 gallon of water to empty tub. Add detergent. Set controls at: Soil Level-Heavy; Wash temp - Warm; Main dial - Bulky Sheets; Extra Rinse - ON; Fabric Softner - OFF. Can now load full tub of clothes and more detergent if desired. Press start button and water covers it entirely. It works so well now, that I went from I hate it to I love it. Been going for two perfect months with no issues. Weird but true. Hope this helps you.

I own a Maytag MDB9150AWB dishwasher which isnt covered under current recalls. Yesterday, I heard a loud pop sound, and it stopped working (also popped the circuit breaker). After taking the door apart, we found burnt wires at the bottom of the door close to where they bend to go under the dishwasher.I called Maytag to find out if they would do anything, since this seemed like a defect in the materials used. They wont offer anything!

Magtag Bravos Washer top load Model MVWX700XW1 - I purchased my washer in June 2011 with the understanding that this was the best washer for my money and needs. I have family of 4, and laundry is a continual cycle at our home. I had the washer delivered and installed by the store where it was purchased. I was pleased with the machine even though the clothes were extremely wrinkled after each cycle, but the salesman was kind enough to tell me this would be so. 21 months into use, I had a water leak from the internal cold water valve. It’s not covered by warranty; I had the valve replaced. Within 2 weeks, the machine would not spin out the clothes; if it did, they were still wet, or would stop mid-spin cycle and start rinsing again. It took 2 hours to wash a 37 minute hand washables load this past Saturday, 4/6/2013, not to mention the other 4 hours washing to regular loads just to get the machine to rinse and spin. The service technician has spent the past 2 days at my home trying to repair my machine to tell me today that it is not the lid lock, but the master control panel which is still not covered under the manufacturer’s warranty. To say the least, I now have to purchase a new washer as I have invested $250.00 for a valve and the control panel is $275.55 plus labor.This machine is the biggest waste of money that I have ever spent. I have been a loyal Whirlpool customer having owned two other Whirlpool machines, each lasting 17-18 years each. I do not abuse my appliances, overload or in any other manner try to destroy a machine for personal gain. I do, however, feel that Whirlpool/Maytag needs to recall these washers or cover the parts beyond what is written. I have read numerous accounts of these and similar issues by others, yet the company will not stand behind their appliances. Really!

My husband and I purchased the Bravos XL washer and dryer set about a year ago as our first big washer/dryer purchase for our new home. We spent about $1200 on the set from Home Depot. I very much regret this purchase as the washer never gets our clothing clean! The washer never puts enough water in the basin and the clothing comes out with strange white smudges EVERY. SINGLE. TIME.I have tried changing detergent, I have tried skipping fabric softener, Ive tried rinsing out the dispenser thinking it was residue from old soap. I dont know what it is, but what I DO know is that the clothes go in without the white smudges and come back out with them for every load. I have to run a second rinse cycle just to get it off, which means Im washing for at least an hour and a half. I DESPISE this machine and its costing me more on my water bill.Additionally, the dryer isnt much better. It constantly shuts itself off even when its not on energy saver mode, with the little red light going on for air flow. Ive checked the connection and dont see what the issue is. If I have a big load such as blankets in there, I have to dry them all individually for almost an hour just to dry my bedding! It simply wont stay on to dry a full load. I very much regret my purchase and wish Id gone with something simpler and cheaper as it would have done a much better job with my laundry. Lesson learned. Dont waste your money on Maytag.

Does not clean laundry, leaves dry untouched spots, all my clothes look unwashed & the rinse is terrible, leaves dirt on clothes due to little water in cycle. Im a senior on fixed income. I cant buy another machine.. I called Maytag within a couple of weeks of using washer. They told me We have No guarantee for Customer Satisfaction. This is a complete scam on their part. If I could of afforded a Lawyer I would of taken them to court. They knew what they were selling & somehow got away with it. Give the people what they pay for, not the Bravos piece of Junk. Can only wash on 1 cycle to get wet wash. But paid for other useless cycles. Who made this machine & who allowed it to pass to the unfortunate Consumers. If anyone can help getting Payback from Maytag, Please let us know... Better business Bureau should get after them.

I have used several brands of refrigerators and Maytag stood out for me. Everything works as good as new. However, my experience with ice machines, has been the first thing to quit.

The Maytag dishwasher works really well. Not the quietest, but cleans thoroughly. I dont use heated drying though, to save energy. Stainless steel interior retains enough heat to mostly dry. However, unit died after only 7 years. Expected longer life.

This washer has been the biggest disappointment of any appliance I have ever bought. Purchased 12/2012 and immediately disliked it but thought I needed to get used to the new style since my previous machine operated for 23 yrs! It is loud and does not clean as effectively as my last machine. It stays in the Sensing mode for 15 mins or longer. Rarely will it spin as it should. Most loads, after the sensing stops and the lights go out, I have to move the dial to Drain/Spin, wait for it to sense again and then maybe it will spin. If this doesnt work I have to unplug the machine to allow it to reset. I called Maytag and was told there are no known issues with the machine. I google this model and find many customers have had a similar problem.

After everything posted here why would anyone take a chance buying any Whirlpool product including all subsidiaries. I made the mistake of buying a Maytag washer and dryer less than 3 yrs ago. There are only 2 people in the household and we only wash linens, towels and undergarments- the rest goes for dry cleaning. The washer stopped filling with water, similar to what was posted by another customer. Maytag customer service was 2 weeks out.When the service tech arrived he diagnosed the problem as a faulty water value but didn’t have the part- another week. I asked the tech why it takes 2 weeks to get someone out for a service call- he told me that there were 4 techs working the area but 2 quit and they were never replaced. The tech went on to say that he was leaving because of the misdirected grief he gets from customers because “the Whirlpool brand is crap”, it takes to long to get service and usually the cost is more than the appliance is worth- and they take it out on him. That is not hard to understand.Bottom line- IF THE SERVICE TECH IS TELLING YOU THE BRAND IS “CRAP” what else do you need to know. FYI- Maytag repairman quoted a new water valve at $70, labor $150 for a total of $230. I paid $600 for the machine- is this a joke? The exact same part was available on Amazon for $43 and was delivered in a day. With the help of a YouTube video I replaced the part in 10mins. On top of the fact that the appliance is crap, it would have taken 3 weeks to get fixed- Maytag is also screwing customers with overpriced parts that shouldn’t have to be replaced in the first place- fair warning, STAY AWAY.

I have been very disappointed with the 2017 model of Maytag washer and dryer as the washer does not clean the clothes as it should. There is the inner part taken out with no agitator and I believe that is the reason that the clothes comes out not white or cleans as I am use to it being before with my other machines. I think they need to reinstall the agitator to clean the clothing thoroughly. The dryer takes longer to dry the clothing and it uses more hydro which cost a lot more monthly for us to have to pay out. I will never purchase another washer and dryer as this in the future.

Maytag Bravos Model MVWB750wq1 - After only two years, the washing machine finally died. The machine was on a f51 code - hardly anything was in the washer. I also smelled a burning smell - well, that was the pump. The machine was not pumping water out. After the repairman came out, the contract company is saying they are not covering this because there was rust reported by the repairman. How can bearings inside a washing machine be rusted? This is a washing machine, isnt it? How are they building machines that deal with water and rust?! I will never buy another Maytag product - thats a promise. I spent over 2000.00 on this set. Never again.

Well I like all the other people have the very same problem. Ruined floor from sheet of ice that forms on the bottom tray daily. I was told I need a new main board which I understand is about $500.00. I am 55 years old and this was my first brand new fridge. I am so so upset. I grew up with the whole Maytag repairman commercials where he was so lonely cause he never had any repairs to do. All my life I grew up with these commercials. I thought I was buying the best. What a disappointment. It has been in my living room for 2 years. I keep thinking something wonderful is going to happen. Now I have to pay someone to haul it off. Great.

We purchased this Maytag top load washer less than three years ago. Spin cycle stopped working and repair for new actuator motor is $240 (machine cost $500). I should have read Maytag’s reviews before we bought it (averaging about 2/5). Living on name - don’t buy one.

Purchased a new Maytag refrigerator in January 2013. In September 2013, the ice maker stopped working and Maytag sent out a repairman to replace the ice maker. In February 2014, the ice maker stopped working again. I contacted Maytag and was told the refrigerator was no longer in warranty. I told them that since the ice maker was replaced in September the warranty should have covered me for a year from that date. The Maytag representative told me that was not had it worked and asked if I wanted them to repair the item for a fee. I bought a non-Maytag ice maker and replaced it myself. It is now July 2015 and the ice maker is still working fine. I am not a repairman.

My oven smelled for weeks after being installed. The first time I self cleaned, the oven stopped working and the door remained locked. It took weeks to get it repaired because we needed a part that had to be ordered. The second time we self cleaned, the oven smoked, set off smoke alarm that had to be disconnected, the control panel bulged, and the door locked. It was Sunday. I wrote a nasty email to Maytag. The service man who came Monday could not unlock the door, and said he had to order a part and would return the next Tuesday if the part arrived.Next, I had warranty issues. I had to get a copy of the purchase receipt from Home Depot to prove that the oven was still in warranty. Out of the blue, my phone rings on Thursday and it was Joe ** from Maytag in Michigan. He had read my email, said he was sorry for all the problems, and if I did not mind waiting 2 to 3 weeks, he would send me a brand new oven, would have it installed, and would have the old oven sent back for inspection. I did not mind (although there is only so many things that can be grilled or you can bake in a toaster oven). Three weeks later, I have my newly-installed new oven with its new, year-long warranty. Thank you Mr. ** and Maytag for the great service.

I, too, am absolutely done with ANYthing Maytag. We purchased our Maytag microwave model MMV4205DS-1 in January of 2016. Within the first year we experienced occasional open/close door issues due to the faulty door latch switches. Now it happens virtually all of the time. The ten year warranty is a joke; it is just a come-on designed to deliver a false sense of security that Maytag will indeed stand behind their worthless products when in fact they wont. I am so disgusted with them.

Bought a Maytag washer MVWC415EW in 4/2015. We dont use the washer heavily but over that time span the paint on the top cover and the side where the cover comes down has bubbled up. It looks like a bad rash but only on a washer. I think the company used inferior paint which can bubble up with the heat of the hot water during the wash cycle. I called the company but they do not cover cosmetic items on the warranty. I think since this was a flaw in the paint used they should at least replace the cover portion which would be an easy fix. Maytags are not what they use be! Last Maytag lasted 17 years with no paint problems or mechanical problems.

Its the worst experience I have ever had with any product. I grew up watching the Maytag man as a child and thinking that must be a top of the line product. Boy was I wrong. I went out six years ago when I purchased my new home and purchased for 1,550.00 a brand new refrigerator with side by side, and ice maker on the bottom, silver in color. It looked great, the quality was and is terrible. The freezer stopped freezing a couple of days after the first year was up. The Service department at Maytag is terrible, I called them for assistance and they were anything but helpful rude is a better word. Its been a nightmare! How could they ruin that good, or even great name of that product. Never will I buy a Maytag appliance again. I tell all of my friends as well. Oh yes so far as the leaking is concerned, my floor is damaged as well.

We bought the Maytag Bravos washer & dryer combo from box store. I wanted an extra large capacity washer to accommodate king sized bedding, and having fewer wash loads in general. Cons: 1 - This machine is not energy efficient when each wash load takes 1:30 to 1:50 each load. 2 - The detergent/fabric softener/oxi dispensers are a joke. Water dumps into every compartment at once. And if there’s still detergent left by the rinse cycle, well you get the picture.3 - The “Bedding” setting is the only one which will provide enough water in the tub to get anything wet. Since there isn’t any type of agitator the clothing/bedding just floats on the surface in dirty perfumed water. 4 - With any of the other settings the water level is so low it doesn’t always get everything wet so items are not being washed properly. At most maybe 2 pairs of jeans or just a few t-shirts can be washed on the “Normal” or “Power Wash” settings. 5 - Because there isn’t an agitator, clothing gets knotted up. Dress shirts, dress pants, jeans, towels, you name it, everything comes out of the washer in a knotted mess.The Bravos XL Dryer: My only complaint with the dryer is that it allows a good amount of lint to pass through into the machine. Then it’s difficult to get any type of lint brush into the vent area to remove the lint. Dampened lint in the machine can make clothing smell musty and nasty. I had to call a service to remove lint from the dryer & ducting because of the odor lingering from the inside the dryer.

Purchased our Maytag Centennial Washer Model MVWC400XW4 2 years and 5 months ago; guess we are luckier than most; it has now failed in the spin cycle, high pitch, high volume whine, sounds like it is about to explode. Needless to say is out of warranty; and too expensive on our limited income to have a technician repair. I will hope to make the repairs myself; nothing to lose at this point; and from reading the countless negative reviews about this product; should be as many countless repair suggestions on YouTube. Obviously if Maytag would stand behind/up for their product as they claim they do; I and many others would not have these issues. My wife and I for sure will never buy another Maytag product until Maytag resolves the issue, which if my calculations are correct will be never. My advice is simple, do not buy Maytag products.

So we bought the whole Maytag kitchen appliance FZ (fingerprint resistant) series suite. That was such a mistake! Id give the part numbers but I think this applies to Maytag in general as it sounds like all of their appliances suck. Ours are 1½ year old and I already want new ones. Over $3,600 for junk. We knew it was no Viking or Sub Zero but didnt expect to flush $4k down the toilet either.The microwave is an over the range type and we have it vented to the outside of the house. The vent works like crap to remove the steam when you have a large pot of water boiling on the stove top. I can put the fan on high and barely any steam goes up the vent, most of it ends up soaking the microwave door to the point where I have to towel it off. The vent will hold up a paper towel so I know its pulling air but the location of the vent in relationship to the large front burners makes it useless. And the self cleaning is as others have already stated - A joke.We bought the fingerprint resistant SS and I would rather have the fingerprints than all of the scratches. Today, and this is no BS, I had a lottery ticket on the fridge under a magnet and I pulled the ticket because I wanted to check the numbers, well I slid the paper about 4 inches while it was still on the fridge under the magnet and now we have these fine scratches everywhere I did this. It wasnt the magnet because it has a felt backer on it, I took the paper off and slid the magnet all over the place, no scratching. I cant believe a piece of paper would even leave a mark at all. This is aside from some larger scratches that someone in the house must have used a feather duster on it or something.The French door fridge is loud and the ice maker is huge! The slide out basket in the freezer always gets cockeyed and stuck like its coming off the track. To line up the door tops you have to adjust the feet on the bottom of the fridge. I have to put ours out of level to get the door tops to line up, well this makes it look terrible in the cabinet space so you have to make a choice of what is uglier - thats just bad engineering. Our old fridge (GE) you could adjust the doors right on the bottom of the door. Its like they forgot this and said, Well you can just tip it one way or another to get them to line up, ya lets put that in the manual. The dishwasher sucks, plan on rinsing everything, even the silverware doesnt come clean. No its not our water.We are so disappointed in this brand which used to be considered very good, what the heck happened? Ship manufacturing over to China? And another thing, I highly doubt this is stainless steel. I know there is ferritic and martensitic stainless that are magnetic but Id bet all of my appliances that this is just regular carbon sheet steel with some coating on it to give a stainless steel look. All except for the range, that is different and doesnt scratch like the fridge, microwave, and dishwasher. Not sure why but probably has to do with the heat so they couldnt use this junk coating, just a guess though. Anyway it doesnt matter, all of the appliances are a complete waste of money. Poor design, poor performance, poor durability, pure junk!

Gave up a very good old washing machine to update to a newer one and so we got the Maytag bravos 300. I thought Maytag was a very dependable name and product. The warranty went out. 2 weeks later, the water pump went out. I had to pay to have it replaced. Then after that it started making noise that got louder and louder and now it sounds like a thrashing machine. And now it has started leaking water out of the bottom. So its going in the scrap pile. What a loss of money - the worst investment I have made. For what I paid for this machine, it should have lasted for many years to come. The washer I had before this Maytag I had for 16 years - no problems at and it still worked great when I gave it away. Maytag use to be a brand you could count on. Great craftsmanship has been taken away and monetary gain has taken over. I hope no one else has to go through this nightmare that I have. Maytag they should have to give peoples money back that we all worked hard for. Going with a LG now, hope its a good machine.

I purchased a matching set of Maytag Neptune washer and dryer about 6 years ago and the washer is junk! It sounds like a jet is landing in the laundry room. The repair man said it is not worth fixing - bad bearing. I am not happy!

I purchased high end Maytag washer, dryer, dishwasher and microwave in May 2010. On Saturday 4/25/14, the Maytag Microwave stopped heating. The fan runs, the panel, display, lights, clock, and tray all work. It just doesnt cook. The Microwave was installed in June of 2010. Not even 4 years old. I have tried to troubleshoot via the instructions that came with the microwave, i.e. Check the demo mode is not on. Dont know why after 3 yrs it would be, but checked it. No help. Pulled the plug out and replaced; turned breaker on and off; checked to see if its was locked. Nothing. I then checked the door and I found that the plastic inside panel on the latching side of the door is pulling away from the door itself, which is part of the locking system. The magnetron shouldnt work if the door system isnt closing properly. The latch system is what is causing the door to pull apart. I am wondering now how much microwave exposure my family has been getting from a malfunctioning door? I have had a Microwave, dishwasher and refrigerator made by Maytag in the past. The refrigerator is 14 yrs old and still works fine. The microwave and dishwasher were at least 10 yrs old when I replaced them with the new Maytags I have now. Here is the problem. Maytag is not Maytag Corp. anymore. Whirlpool Corp now owns the Maytag brand. Prior to the old Maytags I had, I had GE fridge which was junk, and Whirlpool, dishwasher, stove and microwave. They were also junk. I swore I would never buy Whirlpool products again. Surprise.

I purchased a Maytag side-by-side refrigerator in May 2010 to replace a 20-month-old Whirlpool fridge with a dead compressor. The now 14-month-old Maytag has a dead compressor. I have been told by the repairmen that I have come to know that the compressors used in these units are of poor quality and do not last. That must work out well for the appliance industry if consumers must replace a $1,000 + unit every year or two.To Maytags credit, I spoke to customer service and they agreed to cover the parts and labor for the repair even though it is two months past warranty. Maybe I can get another year out of this reliable appliance. I am told that all of the major brand appliances use the same compressor.

We purchased the washing machine (MVWB400VQO) on July 9, 2009. Now we must buy a new washing machine as this one is apparently beyond repair, or else the repair costs will far exceed what it would cost to purchase a new machine. We are completely disgusted with its failure, as we paid $822.36, with the delivery fee and the tax. We expected that this machine would last for years, but here we are, 42 months later, having to again invest in a washer. Now that we have a computer and are able to browse your performance reports, we wish we had been able to read them before, in which case we never ever would have bought it at all.Yesterday it spewed water all over our basement, flooding things that should not get wet, providing an atmosphere for encouragement of mold and rust. The motor is gone as the housing is cracked, which was caused by debris getting into it, something that we could not have known or prevented. This is very poor design by your company, in our opinion. We called some repairmen, all useless as apparently the whole machine would have had to be completely dismantled at a rate of $84.00 per hour, and he could not tell us how many hours that would take, to say nothing of finding a new motor for the thing.We will never again buy a Maytag product as they are expensive with a too-short shelf life and there’s nobody who cares when you need help for something that should not have happened at all. I understand Maytag is really not the good old dependable Maytag we used to know and love at all, but rather is now owned by the Whirlpool Corporation, whose products we will never purchase either.I know why that lovable old Maytag repairman we used to see on TV is retired. Its because he could no longer stand the quality (or lack thereof) of the appliances that you are now producing. He is probably home, hiding his head somewhere and hoping nobody will recognize him. And what, kind sirs, do you have to say about this? Thank you in advance for your prompt reply.

Purchased a new set of Maytag Bravos appliances in 2010. Washer lasted 3 years -- had a failed bearing and repairman said not worth fixing as tub would most likely also need to be replaced. Replaced with a new Speed Queen which has been operating trouble-free. Today dryer quit heating -- repair person stated it needs a new board -- not worth it to me. I am off to now purchase a new Speed Queen dryer. What happened to Maytag quality???

Just dont get clothes clean like the old agitators. Doesnt matter what brand you decide to get I guess. Had Samsung front loader before and was disappointed in that brand as well. Thought them both to be good buys... But miss my really washed clothes!

We renovated our kitchen in 2008 and installed all Maytag appliances. We had purchased a Maytag dishwasher 3 years prior to the renovation-- that we kept. Well, the dishwasher was the first Maytag appliance to go. After replacing several cheap plastic parts on the dish racks (I resorted to use twist ties at one point to hold the racks together) the racks started to chip and rust, leaving stains on our dishes. The cost to replace the racks was about $150 so we just replaced the dishwasher (with a Bosch - so far, no problems!)Then, a couple of the igniters on our gas cooktop stopped working. Since they were the back burners that we didnt use much, we just used a match to light them and let it go. Next, one of the hinges on the double wall oven door snapped. This is a little concerning because the doors are heavy and will need to be replaced. And the final straw concerns our French door refrigerator. The control panel started flashing wildly and the ice door was opening and closing with a loud clicking sound. Of course this happened on a weekend so I looked online and found hundreds, if not thousands, of similar complaints. So I called Maytag and spent nearly an hour on the phone only to be told that my model number was not one of the recalled ones. I explained that my problem was exactly like the others and was told that the best they could do was offer me 50% off any parts. The service call and shipping would not be covered either. The Maytag representative that I spoke to tried to cheer me up by telling me that at least they had the part I would need in stock, unlike the recalled models. Those parts are discontinued and have to be specially manufactured and have a two month waiting period. The part is about $250 and add to that the shipping and service call and I am sure this is going to cost me several hundred dollars even with the discount on the part. Very, very disappointed. Never again will I buy Maytag, never again!

My Neptune washing machine does not drain or spin. It keeps going unbalanced. I am told that I used the wrong detergent. The machine takes a whole day to wash a small load of clothes and then never finishes. Clothes and towels are constantly being ripped and torn. This Maytag product is inferior and we have paid a lot of money for this product that does not work. Repairs to this product are not advised, we have been told that we just need to buy a new one again. This is poor service and poor advice.

I bought a Maytag washer (Centennial) because of its reputation. I didnt even realize this site was out here and would have made another selection had I known. I bought the washer on June 7th of 2011. On June 15, 2012, the washer just quit working. I called Maytag. They said since the warranty was over that I had to pay a technician to come out and it would cost $129. I was upset but I had to have a washer so I scheduled it. The tech came out and said the motherboard was bad. He said that this has been a common problem with this machine and that Maytag should actually recall the part. The replacement part was much better. He suggested I call and complain. The part was $180. He said that Maytag may reimburse me because it was so close to the warranty cut off. I called Maytag to explain the situation, and what do you think their response was? Since you already paid for it, there isnt anything we can do. Nice! What a joke. I will never buy another product from them and neither should anyone else.

Was a Maytag washer. First one lasted one year. Second one replacement one lasted for years. But the company’s warranty is replacing this one without too much hassle. When it runs it does a good job. It’s a big load. All in all a very good washer.

I would like to say that I am highly dissatisfied with paying $1200 for a refrigerator that only can produce ice once every 12 hours and 90% of the time the over fill lever gets stuck so it will not make more. I would recommend anyone to not buy anything Maytag ever.

We are in the process of replacing the 2nd control board in the past 2 years (have has this dishwasher for 3 yrs) on our Maytag dishwasher model MD87749AWW1. The lights on the panel completely quit working mid cycle. At $175 per replacement, we are into repairs for half of what we paid for the dishwasher. Bought Maytag because it is made in the USA but found out that a majority of the parts are imported from China? Very disappointing.

Maytag Dishwasher purchased for $634 on 7-6-12 from Lowes. Control panel malfunctioned in August 2014. Started leaking in April 2012. From the online comments, I am trashing this machine. It is not worth fixing it and having it malfunction again. Maytag will not say anything about this, only offers a repair person out to fix. I am very disappointed that my hard earned money purchased a sub standard machine. Maytag used to mean reliability. NO more.

I had a stroke last year in August and my children got together and bought me a washer. And after the third use this thing started messing up and I had to call in someone. Now the warranty is up and I am sitting here with a new broken down machine.

In the last 6 years, Ive had a Whirlpool dishwasher that the motor seized due to poor design and overseas Asian motor builder (3 years of normal service). I cleaned the motor and it seems to barely work another couple of months but the design and manufacture process was garbage at best. Thinking I would go with the best produce MAYTAG (Old commercial about repairman having no calls), only to find out that it too was bought out by CRAPPY WHIRLPOOL and it too lasted a couple of years with cheap MADE IN CHINA electronics!!! Thats why we are the laughing stock in the world as far as products.I remember the days of where built in the USA was the best of the best, now with selling our great nation down the toilet so some Wall Street Commie can make his/her biz-zillion dollars and sell this nation down the toilet. Maybe they need to go down to Arlington and see who really has paid the price for their luxurious life-style!!!

Maytag 6.2 Induction Freestanding Range Model MIR8890AS0 F47 - I am a very careful shopper. I spent many, many hours researching and searching for the best value. It took me over 2 weeks of research to find an induction oven we could afford. We are a family of 3. Normally, we use just one burner for dinner. We bought the range in Feb 2013. On August 5. 2014, we had company over for dinner. I used more than 2 burners and the oven at the same time and the right 2 burners quit working; I now have the dreaded F47 code. I have had numerous Maytag Authorized repairmen out. They ordered every part except for the one that was necessary to fix my stove. I purchased in Feb 2013, burners went out 8/5/14. This is only 18 months old and is JUNK. Arent our landfills full enough?Maytag customer service is awful. I spent hours on the phone, mainly on hold, in efforts to get help. Maytag claims to have such a great 10 year limited warranty but they wont warranty this F47 issue. Thank God I bought insurance with an outside company. The wrong parts that were ordered were at least covered by my own insurance policy; no thanks to Maytag. I am angry that I have to search all over again to try and find the right stove. I am now fearful of induction. I invested in a lot of induction cookware which was an added expense and burden! They need to stand behind their appliances!People cannot afford to waste thousands of dollars every 1.5 years to cook their meals! This has been an extremely unpleasant issue. It has cost me many hours of waiting for repairmen, waiting on hold, getting and storing many wrong parts ordered by repairmen. I calculate this cost me over 50 hours of my life on the F47 problem. Not to mention the time it took me to shop for this junk to begin with!I think they need to recall this issue as it is clearly a design flaw. I researched this and found many other owners had similar problems. The F47 means that the user interface isnt communicating with the range (the circuit board). They placed the circuit board under the burner surface area, sandwiched between the burners and the oven. It was just a matter of too much heat before this board shorted out. The cost to replace this board is over $600. I am afraid of investing another dime into this machine. I wasted time, energy and A LOT of money on this inferior product.

We bought this Maytag dishwasher two years ago with a two year warranty. We paid close to $700. Six months after we bought it, it started having problems on and off. They are including: leaking water, lights going on and off, cycles are not completed. We changed the console once, and soon after that it broke down again, and this time is out of warranty. Total repair times are: 6 times in two years. My husband call the company, asked them if there is a recall for this model? They told that there is no recall. Then the repair person came. According to his repair experience he said this is the common problem and he got a lot of calls for the same problem. If he told the truth about this, then the company was lying to its consumers!!

I bought a Maytag dishwasher (model #MDBH979AWS3) from Home Depot on July 2010 and had it installed. After 2 weeks, I found water leaking into the basement. The installer said rubber gasket in water line de-laminated and caused leak under the dishwasher and flooded the floor to basement. Product defect and water damage covered by Maytag insurance. Now Feb 2012, about 1 1/2 years after buying, the touch panel controls dont work. I called Maytag regarding any control panel recall and they said no and its out of warranty. The advice given was that they can send out a serviceman for $269 to fix with parts, labor and one year warranty. It seems like planned obsolescence. Dont buy a Maytag.

We are having the same problems with the drain clogging and bottom of the freezer filling with ice and then water all over the floor. We currently de-ice the freezer once a week. After paying top dollar for what is advertised as a top product, we expect better service. Especially when Maytag is fully aware of this problem. We sent an email of complaint to Maytag. Heard from them today. They would pay for the replacement part but not the labor. Most places around here charge $250.00 just to walk in the door!!! Is Maytag kidding?!?! NEVER AGAIN. Will also tell anyone who will listen to stay away from Maytag. No wonder they dont belong to the Consumer Resources group!!

Maytag needs to step up and admit that they have a design flaw in this dishwasher. The problem is that just a week or two after the warranty is out, it just stops working. Sometimes when you walk by it, it just turns on. No way to turn it off. Nothing works on the control panel. From what Ive seen on the internet, everybody is having the same problem. Its the control panel. It costs 180 dollars to fix, but it only lasts another year and you have the same problem. Ill have to say that when it works, it does a superb job. It just wont keep working.

First Maytag washer we bought in 2003, worked flawlessly for 14 years, bought a new one in 2017 only because my wife wanted a bigger washer. Bought a Maytag top load MVWB765FW0. What a big mistake. In less than 3 years it has failed already. The water inlet valve went bad. Maytag offers no tech support because they want to charge you with a service call. I found out what was wrong by researching the problem and error code online and bought the part for $55.00 and fixed myself instead of them charging $100.00 just to show up at your door plus the part and labor. A washer failing in less than 3 years is totally unacceptable and I will never purchase another Maytag/Whirlpool product ever again. Someone needs to wake up at Maytag.

I will never buy another energy efficient washer again. My Bravos is supposed to save money and be environment friendly, but when you have to wash clothes more than once to get them clean, theres no savings. Ive tried different detergents, cleaned the washer, rinsed twice, added vinegar, baking soda and everything imaginable to get the clothes smelling fresh without any luck. I have had several items ruined because the bleach dispenser pours onto dry laundry. Im disgusted.

I bought a new top loader Maytag washer and dryer on 1/1/16. My first experience with the washer was as many in has stated - It Doesnt Clean, the clothes, also I have trouble with the fact that is there is a string loose, it become worst. Why did they improve a product that did not need improving. They just made it worst. It is totally **. Im stuck with it as I cannot afford another washer. The dryer work fine.

I have spent a lot of effort leveling my machine, and my wife balances the load very carefully, but 10 times during a cycle, it will start slamming the tub around, so loud you can hear it from the street. I, like others in this forum, thought I was buying the best washer in the market, and paid extra for the Maytag name. It sounds like from the other complaints, that my problem is just the tip of the iceberg. It will cost me $200 to replace the suspension rods. I wouldnt mind paying the money, if I thought it would fix my problem. After reading about all of the other problems with the Bravos, I might just cut my losses, and get a new one. What a waste of $1,000.

Purchased Maytag Dishwasher MDB8959SFH4 as part of a kitchen renovation with hardwood floors. Realized that the dishwasher was leaking intermittently. Appeared that the door wouldnt latch properly. Called Whirlpool (parent company). Technician came out to assess the situation - couldnt recreate the problem so suggested replacing door seal. I try to explain to him that in my opinion it wasnt the door seal but a failure to latch because the top rack was not retracting completely on an intermittent basis. He also suggesting replacing the latch. Repair was carried out and same issue arose three days later. I systematically removed one dish at a time and then tried closing the door - after removing about the 6th item the door closed. Called the repair company today and they told me he had just received a recall from Whirlpool - apparently an issue with the tracks not allowing the rack to retract properly - what I have been saying all along. I called Whirlpool but they insisted the notice was sent out some time ago. I called Home Depot where I bought the appliance and they confirmed that they were not aware of this issue. I suggested they should not be selling this dishwasher until Whirlpool remedy the manufacturing defect. I will follow up with Whirlpool to let him know I have spoken with Home Depot and they were not aware of the issue.

Almost one year to the date of purchase, my Maytag glass top range stopped working. The oven is still operational, but the range top does not work. The knobs turn and the surface lights go on but the elements no longer heat up. Trying to get a response from a real person at Maytag was impossible. I was put through a myriad of prompts that led me to scheduling a service appointment. I called AppliancesMart and got a wonderful sales person who said a service call would cost me 60 to 80 dollars and that he had not heard of repairs below $300 for this type of problem. Needless to say I am very angry and disappointed that I had not done more research before I purchased this item. If I can prevent one more person from making this same mistake, I will get some modicum of satisfaction out of this horrible experience.

Purchased this dishwasher 3 1/2 yrs. ago. Control panel went out. We would have had to pay almost the cost of new one to replace the part! Maytag used to be reliable. The dishwasher we owned previously (not Maytag) was still working after 12 years!

It is impossible to dry clothes in the dryer without the worst wrinkles you can imagine. I have 2 of them and they are both horrible machines!! The drum spins too fast which causes the clothes to get stuck against the tumbler fins. The centrifugal force holds them there and they just ride around without tumbling in the drum. When the cycle is finished the clothes have been dryer while jammed up against the fins and they are so wrinkled you have to wash them again. The ONLY way to get them through a drying cycle without a tremendous amount of wrinkles is to stop the machine every 5-8 minutes and fluff the clothes around inside the drum by hand. DO NOT BUY!!

Maytag dishwasher quit working 3 years old. No power. Control panel dead. Piece of junk product.

This machine sucks. Im down to washing three to four items only on an extra capacity machine because every single load becomes unbalanced. Feeling the weight of each item and then placing it correctly doesnt work. Repairman came out. Said it was balanced. Lie. At this point I want to take a sledgehammer to it and send the pieces one by one to Maytag. They should be embarrassed to even have this product for sale to the public with their name on it.

Just bought a Maytag Bravos 4.3 cu ft washing machine from NFM. The first machine delivered was broken it didnt wash or spin the clothes. NFM sent out another one at 9:30pm. It doesnt spin the clothes out well & loads have to be small. Poorly made.

It is quiet and cleans well but thats where it ends. We have had it a little over a year now, after just a few months it started leaking, fixed under warranty. Now one of the upper rack tracks is broken, it was held together with three very flimsy welds, hopefully will be getting it fixed soon. We are going to wait and see what other kind of repair it will need, I think we would have been better off to just buy a cheap dishwasher!

I purchase a Maytag dishwasher from Home Depot on 12/31/11. Based on the their commercials, I thought they were dependable. I did purchase an extended warranty, as I always do with any new appliance. After 2 years, the dishwasher stop working. I contact Home Depot and the extended warranty and was told to contact the manufacturer. Maytag blamed the extended warranty for the problem. They told me they could not help me. And could not help me. I will never ever buy any appliances from Maytag again. This model is M936/110V cord.

My double oven was purchased over 6 years ago. They have been served yearly and work fine. The only thing is the cleaning cycle which if used at the high temperature to clean can affect the oven temperature control. I don’t use this function anymore.

The dishwasher would not start July 30 2015. Tried to get service around here and no shops could respond. Called Midsouth Distributors for circuit board. They did not have one but would order and gave me the part # W10595570 based on the Model # MDB7749SBW3. Hoping could find one quicker somewhere else. Ordered one overnight from Sears and planned to replace the board by myself. However, I noticed the flat wire with 14 wires in the ribbon cable had brown spots. From my experience in the electrical systems, I realized this must be shorting out the start signal to the dishwasher logic controller. Sure enough, after scraping this off with a sharp knife, I was able to start my dish washer.My previous MAYTAG lasted 20 years. I bought this one in February 2014 at Home Depot. The design for the electrical controls is obviously very poor as testified by so many angry owners. MAYTAG should be required to replace all these control panels with a improved design at their cost. I hope this obvious poor design of a part gets attention in the United States and ConsumerAffairs will help us. I have called 1-800-688-9900 and registered with MAYTAG a complaint about this poor design.

We have a model MF12269VEMS. Approx 3 years old. Ice maker and water dispenser work great. Fridge works well. We have experienced over the last 6 months a buildup of ice that forms inside the freezer under the drawers. If we dont catch it every 4-5 days we cannot open the drawers as the ice catches the bottom plastic drawers. I called Maytag directly and the pleasant young lady told me after checking that it did not seem to be an issue...clearly after looking into the internet I am not alone! Maybe someone can email me a fix?

Bought a Maytag HD top load washing 11/4/17. Within the first month the machine began to make a loud squealing noise during the wash cycle. A repairman came out 2 times before finally replacing the gearbox and tub. Within the last month or so the problem began again, another repairman came out twice, and once again, had to replace the gearbox and tub. When he left I ran a load and the machine sounded like a war was occurring inside of it. Very loud banging and grinding... heck I was wishing for just the squealing back! Maytag refuses to replace the machine and just keeps sending out repair people. The Maytag name once stood for quality but that was long ago.

Purchased a new stainless Maytag dishwasher model # MDB4949SDMO ser # F54240259 on 10-20-2015. Installed about three weeks after purchase. This unit is terrible -- has not properly operated or cleaned our dishes since installed. First service came shortly after install. Complaint was unit leaves white film on all dishes. (Soap used is cascade which was recommended by Maytag in owners manual.) Technician installed a new water fill valve because unit wasnt getting enough water. After that unit still no good as unit became noisier and noisier and still leaving white film on all dishes. Second service call: the technician indicated entire noisy pump assembly would have to be replaced and would need to order it. Third service call: the technician arrived and replaced entire pump assembly, taking the old one away with him. The technician said it will be good now. It wasnt, but at least it was quiet. That was in January 2016. This unit still does not clean dishes properly -- continues to leave a white film on everything requiring hand scrubbing to remove. All dishes are hand rinsed with hot water before loading them in dishwasher, but actually dishes are more dirty three hours later after the cleaning cycle has finished than before they were put in. After having to buy new glasses and plastic ware because stubborn white film will not come off and looks disgusting. Tried various different soaps and rinsing products to no avail.Finally contacted service department for the fourth time and today technician arrived and found the unit to be mechanically functioning as it should and can do no more to help. Said to try a product called lemi-shine. Maybe my water is too hard also he said, even though we are on city water! This is our third dishwasher at this home and have never had hard water associated issues. All I want is my full refund for this defective product and I only get the run around from Maytag. Stay away from this machine.

Purchase washer and dryer January 26th, had delivered said February 2nd. Had a horrible delivery service, delivery men were very rude and scratched the dryer. Washer never worked correctly, called and had exchange set up for February 9. Washer was delivered on February 9 and again we had a horrible experience with the delivery drivers. They scratched the washer. The owner of the delivery company came to our home making sure everything was correct. Washer worked well for two and a half weeks. Then I noticed the water was slowing down when it was filling. Then this morning the washer completely stopped filling. We called Maytag and they told us we could not get anybody here until next Saturday. They were rude on the phone. We then called Home Depot where we purchased it and said we want to return the washer and dryer. They said we cannot return it. We are stuck with it. Now weve been arguing with Home Depot and Maytag all morning trying to get someone to my home to get the washer fixed. This set cost $1,400 and Maytag is not supporting us on selling us 2 lemon washing machines. We are stuck because we cant return them or exchange them. Home Depot gave us an option to exchange for a lesser model that they have in stock. When you read the reviews for that model the reviews are terrible. I would highly recommend that you do not purchase a Maytag or Whirlpool product. Their company does not stand behind their products or their workmanship. If I had the opportunity I would return these to the store. But it has been over 30 days and I believe that is not an option. Stuck with a lemon. Very sad that customer service is so crappy on an American-made product.

I purchased a Maytag dishwasher four years ago and it has been serviced six times in those four years. Not just small things, main parts. Control board twice, control panel twice, and cleaning terribly the other two. They replaced the control board once and then would not do anything after that. I just got it replaced four years into this nightmare only because I bought a Sears home warranty plan and they are replacing it. I would never buy a Maytag appliance ever again.

My husband and I purchased this Maytag bravo washer in May 2014. It is not even three years old and the bearings went out. Call the repair man and it would cost over $300 to have it fixed. I paid a lot of money for this washer, expected it to last more than less than a little than three years and I think its terrible. Its loud, water was leaking all over the floor, its just a terrible terrible washer. Maytags reputation is not as good as it used to be. Model number mvwx5008wq and ser number. C41430792. If you are planning on buying a washer do not choose Maytag!

Bought this Dishwasher two years ago. Control panel was working intermittently now it does not work. I am looking for anyone with this same problem. I know lawyers who are class action specialists who fight for the consumer. We need to make Maytag responsible for the flaws they have in their product. From reading these other reviews it seems that this control panel issue is consistent no matter what model you have. They must all share the same electrical components that is causing this issue with the control panel. My model number is MDB8959SBS2.

I have enjoyed my microwave and it has lasted 10 years so far. The only problem I have had is the handle coming off but I clip it back on. Also I changed the bulb. The microwave is over the stove and matched the rest of my appliances. Basically, I would recommend Maytag for any appliances that a person would need to buy.

I purchased a Maytag Bravos Quiet Series 400 in 2010 and it is now leaking like crazy and sounds like the bearings are going or gone in it. I researched washing machines for over a month before purchasing, and it seemed like this would be the machine for our active family. So much for research. It washes clothes okay, but is a bit rough on them. I found that it has ripped some of my more delicate items. When I contacted Maytag, they sent me an email with contact information to purchase a maintenance contract for $395 which would cover the machine for only 1 year. My husband is very mechanical and took the washer apart thinking the seal/gasket may have come off. He cleaned up the seal and the area around it, and put the seal back on. It did not help. He also noticed that the drive shaft to the motor was beginning to RUST! This machine is only 2 1/2 years old! So, if you are noticing that your whites are getting orange spots on them, this is probably happening to your washer, as well. Maytag should step up to the plate and recall this machine.

In December 2010, we purchased our Maytag Quiet Series dishwasher model #MDBM601AWB3, serial #NY2916421. At first the sanitize light quit working about 6 months ago. Today, September 30, 2012, this piece of crap will not turn on at all. There are no lights on at all. We paid almost $600.00. As far as being quiet, oh yes it is quiet alright! We the consumers are demanding a recall. Look at the complaints! Its a manufacturer defect in these control panels. I will not be forced into buying another dishwasher or a control panel. I want this company to stand up and say theyre sorry and fix this problem for all of us Americans!

In July 2001 my husband and I purchased a 6-year old home. We are still here. We have replaced the refrigerator, oven and microwave - all in stainless steel. I am still waiting for the Maytag dishwasher to wear out. It has never been repaired because it has never broken down. Cleans dishes and silverware great.

I bought my Maytag Refrigerator about 7 years ago and the night mares have not stopped. The ice maker has broken down so many times, I forgot to count. The drip from the ice maker lands on the floor of the freezer and drips out to the floor. The cold part of refrigerator end up freezing the fruits and veggie and milk.

I purchased a top load Maytag washer the spring of 2019. My clothes come out partially dry, with a film/residue, and debris left on them. I was told that they use considerably less water; however there is not sufficient water to wash away small amounts of anything left on clothes. I have contacted Maytag 3 different times. Each time my concerns have been dismissed. The only solid advice they gave me was to use less soap, which hasnt changed anything. They also told me to clean my clothes before I put them in the washer (we have no children at home; Im not talking about really dirty loads). They told me there was nothing they could do, and I was just stuck with the washer. I am completely dissatisfied with this product and the Maytag service. I would not recommend their washer or their service. The dryer works just fine.

Okay, on March 2009, we bought this brand new microwave due to our major remodeling. We didnt move into the unit until February 2010, so the microwave was in its box for 11 months. After we moved in our condo, my husband and I had to travel for work for almost a year so our brand new microwave is very slightly, gently and barely used. Well, for the past 2 months, it had been acting up. Sometimes it heats, sometime it doesnt. For a 2 year old microwave, which we paid over $400, I would assume that it would last. It no longer heats up, so I called Maytag customer service to hear her tell me its not covered under the warranty and would cost $269 for repairs and there was nothing she can do for me unless I pay for a technician to come and repair it! No way, I swear it probably got used 5-10 times a month to heat up coffee for about a year. I am sure there are some major quality issues on this model because when I googled Maytag microwave, all I see is the same magnetic problems. I spoke to a group of my lawyers friends. If youre interested in joining a class act law suit, please e-mail me. I hate that people are being taken advantage of by these terrible companies. I cant believe how low quality their customer service and products are. Believe it or not, my $30, old microwave lasted me 14 years throughout my college years until we decided to replace it with the modern stainless steel one. It got noisier in time but not broken and still heats up just fine. This $400+ one lasted me only for several uses. Shame on Maytag, when I have time, I will be sure to write a complaint to the consumer department as well. I will dedicate my life in spreading the word out about their low quality product. Don’t buy Maytag unless you only plan to use it for a year or 2.

We can do nothing at the control panel even though the drum light will come on when the door is opened, we cannot turn it from the control panel. After a varying length of time, a fault code of F70 is displayed (which is not covered in the owners manual), the dryer can then be started by depressing the power button and all functions seem to be restored.

I bought a Maytag refrigerator model MBB1953XEW three weeks ago. According to its features on the Maytag website, its supposed to be quiet (QuietSeries 100 sound package). Ha ha, make me laugh. Its the noisiest refrigerator Ive ever had. The repair guy checked it out this morning. He spent about 5 minutes running some sort of test with the help of his iPad. He then told me everything was perfectly alright, the noise was normal for a Maytag, and that I was going to get used to it.Needless to say, he had a totally condescending attitude. Its the first time I ever bought a Maytag. Previously, I had a General Electric that was noisy but not as much as the new Maytag. Prior to that, I had a good old Kenmore that was perfectly alright but that I had to give away for other reasons. This time I chose Maytag because I thought it was good quality and I wanted it to be very quiet. Well, nope. Next time, for sure, it wont be a Maytag.

This review is pretty simple, if you have kids, do not buy this washer! I just went to the local wholesale guy after almost 8 months of using this POS, and spent $200 on a older agitator machine, after the first load my 7 year old close came clean of dirt! There is literally no water and the motion of the drum, it is almost impossible for this machine to clean clothes. I really am surprised that no one has started a class action. And to anyone saying the are hog farmers and work outside and get dirty? I would love to see it first hand. I am going to post on YouTube and show what this machine really does. Think about this before you buy, We all get hooked on how big it is, thinking you can do 4 loads at once, but trust me the low water thing is real! How do you clean clothes with no water! You will regret this purchase. And I am a Maytager for life! So disappointing.

I had a stackable Maytag dryer that was bought in 2016 but only used during the summer of 2017. Last May the dryer stopped heating. I contacted Maytag and they sent a repairman a week or so later. He identified the problem in the electronic control and ordered a replacement part. The part came and he installed it a week later. The part was faulty and he ordered a replacement for the replacement. It arrived a week later and also did not work. He said he had problems with replacement parts but contacted the technical service department at Maytag as he did the first time. The technical service person said there were problems associated with new software being not compatible with dryers in the last year and we needed a new control panel. I contacted Maytag again waiting the usual hour to get through on the phone. They agreed to replace the parts for free and ordered a control panel that arrived a week later. The technician installed both parts but they did not work. I contacted Maytag again and after waiting the required hour talked to a person who said she would contact the department who could arrange a replacement. They contacted me a few days later and said they would supply a replacement for $250. This was delivered a week or so later but they did not have a stacking kit and returned to the delivery company with the dryer. A week later they returned with the stacking kit but forgot the dryer. A week later they returned with both the dryer and stacking kit but the installer (always a different person) said he was too big to get in the space behind the dryer and that the venting supplied was wrong.I bought new venting from Home Depot and a new installer arrived a week later. He said the new venting was not necessary and in fact wrong and installed the dryer. It ran but foolishly I did not check to see if it heated and neither did the installers or if they did took off without letting me know that the dryer, like the one that was replaced did not heat. I discovered this a couple of days later when I tried to use it. I contacted Maytag and they setup an appointment for a new service technician to visit. I contacted Maytag again today hoping to get some explanation of what might happen next or some explanation. They had no idea but did inform me that they would not replace the new dryer but would start repairs again.

Purchased a non agitator washer 1 year ago. Constant frustration with the sensing technology. Cannot select a water level or load size. The expectation is that the machine will do that automatically. The water dispenses through the soap container adding soap to dry clothes which then leave white marks on dark clothes. All of the selections for loads do not have a water level close to covering the clothes. The only way to achieve coverage is to reopen the lid multiple times to restart the sensing feature. Another option is to add wet clothes to increase the weight to “fool” the sensor. Some clothes have come out of the wash still dry in areas. Every load, no matter what size takes a full hour to complete! There is no quick load to be done! I have paused the cycle to leave the house and the water drains from the machine causing you to begin your 1 hour cycle again. Epic fail by the Engineers to provide a user friendly machine. This one, as time goes on, just becomes more frustrating and yes very noisy during the spin cycle.

We spent over $1,200 on a Maytag washer on 12/2015 and it did not work properly. The door got locked, had a couple loads moldy because we could not get it open. Didnt drain either. Maytag had someone come look at it 3 times and it still didnt work. Called Maytag and now they told me that they cant do anything about it because is not under their 1 year guarantee. And of course they are very sorry for my unfortunate inconvenience. I thought they had a good honest reputation but... Im just disappointed!

We bought this washer before Christmas. I was very excited. However my clothes don’t come out clean. I am actually washing my white uniform with hands because each time I wash, dark scums remain on my clothes. I think that the machine sensor does not sense how much clothes are in there and how much water is required. This machine is very disappointing, it needs to be recalled. See pictures below.

Read MANY complaints about these units leaking water onto the floor underneath. This is accompanied by a sheet of ice forming on the bottom of the freezer under the main drawer. Good money says the cause is a plugged drain tube. I had a Subzero that suffered a similar problem. The factory installed drain tube was a flexible coil type and food particles would be easily caught, compromising water flow - leading to an ice plug and eventual evaporator ice-over. I replaced the factory tube with 1/4-inch rubber fuel line and the problem went away for good. With the Maytag units, if memory serves, access to the drain tube is from the back of the unit. You have to remove an access panel to get to it. There is typically a small removable rubber restrictor cap on the bottom of the tube; this is the most likely spot for a clog to form. Due to its design, IMO, clogging and ice-over will probably be a periodic thing. If you are really handy, you can do this maintenance thing yourself.

I bought my Maytag dishwasher MDB7749SBM0 three years ago. After it was in one month it already needed a service call. It needed a control panel. Out of the dishwasher 4 weeks because this happened over Thanksgiving. Two months later it stopped working and needed another service call. Technician was inexperienced and another one had to be called. Out of the dishwasher 3 weeks. At this time, and because of the expense of the machine, I purchased an extended warranty. This was control panel number two. Not long after, the heating element had to be replaced. Two weeks without the dishwasher. Now, my dishwasher stopped working again and it needs a new control panel. The technician is rude but did offer the information that the moisture ruins the control panels. IT IS A DISHWASHER!!! IT USES WATER!!! I only run the dishwasher twice per week so I cant imagine how poorly it would hold up if it was run more often. I am on my third week without the dishwasher because the part is on back-order! No one can tell us when it will be in. I bought a Maytag because I thought they had the appliance market under control. MY MISTAKE! I am very angry.

Maytag dishwasher model MDB4949SDE3: This dishwasher is the biggest POS that I have ever owned in 40 years. The first one would never turn on and fill with water and after it finally did it leaked on my new floor. Waited 10 days to have it replaced. The dishwasher cycle is 2.5 - 3.5 hours and the dishes come out dirty. The top rack is not adjustable to wash odd things. I feel that these dishwashers need to be replaced.

Neither appliance (Neptune dryer and washer purchased in 2006) was worth the price paid. The dryer drum actually cracked and the washer repeatedly gets hung up on 3E. I called about the dryer and got an Oh, well response. “We dont know whats happened to that dryer.” What happened to both appliances is that they were used for their intended purpose. I do laundry for my husband and me. Is that too much for a Maytag? Customer service is equal to indifference. So much for Neptune. And thanks for standing behind your products. What is the life expectancy of a dryer drum anyway?

I wished I researched more before I purchased, but like most people, I believed in the reputation of Maytag. Like many others - my control panel started to go out 19 months after install: Had my first event with the washer; it would not allow me to select normal wash. A high-end machine shouldnt have electrical connection problems within 19 months, just 7 months after the warranty expires.When the repairman pulled apart our machine, he found a similarly burned looking touchpad ribbon cable, that was burned in exactly the same position as the photos shown on Maytags website under the review referred to. Maytag/Whirlpool has set up a special phone number to deal with this problem: I dialed 1-866-931-7384... Been on hold for over an hour Of course - NO answer! Ill try later but I am very angry that this has been a known issue BEFORE I purchased mine at Home Depot. What a piece of junk. This is the last Maytag Ill ever buy again. The service is horrible, the product is junk.

Ive had this Maytag microwave for about 4 years and the magnetron had to be replaced. The keypad was replaced three times due to SE code shutting down unit which happened again. When I explained this to Maytag, they said it is out of warranty. I explained to them that the last keypad which was replaced was only 6 months old. They replied but the unit is out of warranty! I would never recommend Maytag or any affiliated companies to anyone.

Great appearance, great job on getting our clothes clean and dry. Good dryer cycle choices and output. Good washer cycle choices and output 98% of the time, BUT, sometimes the washer needs a do over about once in 50 loads. Overall, two thumbs UP.

We bought the Bravo XL set 11 months ago and the washer leaks all over the place.. Called Maytag and had the repairman show up. Upon arrival he told us these were the worst machines to buy and would never recommend to anyone. He also said that business has been great due to all of this.. He checked the washer and said the water pressure was too high and lowered it. He couldnt find anything wrong with it. After he left I started a load and sure enough it was the same. Called him right back and he said to call Maytag because he was going to another repair job. I called Maytag again and they said to call the repair guy.. Never again will we ever buy Maytag.

Model MDB4949SDZ0. 7/10/2018 Purchased from Costco. 7/23/2018 Installed by company arranged by Costco. 6/18/2019 A burning smell was coming from front control panel area of dishwasher when it was turned on. 6/25/2019 & 7/3/2019 Repair technician came to fix but could not find anything wrong so burning smell continued whenever dishwasher was one hour into cycle. 7/12/2019 Repair tech changed out front control panel because burning smell was still coming from handle area. 8/9/2019 Dishwasher does not drain completely when wash cycle is complete. Sometimes there is sudsy water left, sometimes it is clear. The water level is above the heating element at bottom of dishwasher.We only run the machine 2-3 times a week and have been using different cycles to see if the draining issue is with one cycle or all of them. No matter which cycle is used, water remains at the bottom of the dishwasher above the heating element. This seems like way too much residual water. Repair technician is scheduled to come for the 4th time to look at dishwasher but we just received a message that we will have to pay $129 service fee because dishwasher is now out of warranty. Maytag, fool me once, shame on you. Fool me twice, shame on me. Therefore, know that we will not be purchasing a Maytag product ever again.

I purchased a Maytag Bravo washing machine item # 26 23872 for $617.69 on 11-23-11 and it was delivered and set up on 12-02-11. My problem is if you have dirty sweaty clothes, you cannot get them clean with such little water. I used the HE detergent as directed. I talked to a woman at the local Sears Appliance store this morning, 7-11-12, about it. She said I need to use Affresh. So I did clean my washer but with a similar brand and my clothes are still stinky. I have even washed an empty load or two with bleach and hot water. I make sure I wash with hot water and completely dry my clothes.When you take a bath and dry yourself off with a towel, it smells like a musty basement. I am allergic to mold. I cant even take a wash cloth, get it wet and wash my face without wanting to throw up from the smell. I have had guest comment on the towels as well. Its embarrassing. The problem is you cannot clean something with an inch of water in the machine. I am 58 years old and now have to do the wash. I went to the store and asked if we could return it for an exchange or anything like a discount on a new one and she would not budge. She said it had to be within 90 days but 90 days was in the middle of winter and I was not having dirty sweaty clothes from doing outdoor yard work.Now that summer is here, 7 months later, my clothes have been smelly for a few months. I cant take it anymore. I showed the woman that I had been to Lowes and had an estimate of 10% off with free delivery, set up and haul away. She said she could do 15% but when you add on the delivery fee, it was higher than Lowes. I purchased my whole upgraded kitchen stainless steel appliances for about $7,000 and this set of washer/dryer but Sears could not help me out? What a disappointment that a loyal customer such as me could not at least get free delivery on a new washer. I went right back to Lowes and ordered the same machine I wanted Sears to sell me matching Lowes price.So now, I am stuck with a 7- to 8-month-old machine still in the one year warranty that is like new but is a worthless piece of junk as my clothes all stink. Run, dont walk if someone tries to sell you a low water HE machine. I tried sending this letter to searsinfo.com corporate office and it is rejected even though the website gives you that address.

MDB4949SDM1 - After owning Maytag model MDB/C-2 for thirteen (13) plus years, I decided to purchase the subject Maytag Model when my 13 year old died. Big mistake. Previous model was very simplistic in rack design and it provided user-friendly options such as two detachable baskets for silverware and a special rack for delicate items.The new model has been designed so your dishes go in on angles on the top rack and as such bowls, small plates etc never stay in place once you move the rack and the lower rack configuration was redesigned and the rear area which was open to allow for bigger pots and pans to fit better has been removed, so now you have to lay your pans on top of the tines, very difficult to low the dishwasher.Additionally, I purchased the stainless steel model; apparently in the coating process a drip pattern was sealed that you can see when sunlight hits dishwasher. Further the stainless steel face that they bond to the door has popped, so when you grab the handle the face pops in and out. Lastly the new design has an adjustable upper rack; I tried numerous times to adjust the rack and couldnt so when I called Customer Service for these issues, it basically boils down to if the Service Man comes out and determines my issues are cosmetic and the rack which Ive never been able to adjust should happen to work then I have to pay the service call as there is not warranty coverage. So I declined the Service Call and advised that this would be my last Maytag purchase. I highly recommend anyone considering this unit fully investigate and test out before buying.

Purchase a top loader washer machine in Nov 2014, it is now Jan 2015. It is not completing drain cycle, leaving wet cloth. I am Not happy with the service. I had the tech people come out 3 time and saying to call customer service, and they keep sending out people. They do not want to give me back my money. Unhappy, waste of money, will not get another Maytag appliance again.

I have owned this washer for 3 years and purchased it to match the Centennial Dryer and because of its advertised commercial grade components. The washer has just now turned 3 years old and has never been abused but I have been told the drum bearings are going out.

We purchased both a new Maytag washer & dryer in 2011. Our dryer, Model #7000XG1 all of the sudden started thumping when we were drying our laundry. After we called a technician to come out, he stated we had a crack in our drum. How in the heck does that happen in 4 years time and only laundering for 2 people? Of course this steel drum should not wear out before the other parts, but it did. Since there is a backorder on the replacement drum, it makes you wonder if this problem is wider than it seems. Also, Maytag would do nothing for us other than offer us the purchase of a new dryer at a discounted rate good for only 7 days of their offer. Seriously, how about standing behind your product? And, then again, why would we be enticed to spend that kind of money on the same type of product that has flaws? Uh, duh Maytag or Whirlpool. Silly fools you are.

I bought my Maytag Centennial washer & dryer about 2 yrs ago. It wasnt long after I bought the set, that the washer started having problems. I noticed the button to turn it on wouldnt go off. Then it was a pain in the ** to not be able to open the lid while the water was filling up. Something I havent noticed until today, its suppose to fill up to the amount of clothes that is in the washing machine. Well when I opened the lid there wasnt enough water in there to even cover all the clothes. Now I know why my clothes are not coming out clean!!! I am so frustrated with this machine and the company!!! DO NOT BUY THIS PRODUCT!!!!!

When my house burned in 1995 I purchased all Maytag appliances when we rebuilt because I had good performance from them up to then. My washer and dryer even made it through the fire and are still going now 14 years after the fire. They are 34 years old. The other appliances I purchased were a chest freezer, dishwasher, stove, and, a refrigerator totaling around $2,000, a pretty sum in 95. I have nothing but good to say about the freezer and the dishwasher, however, the refrigerator and stove stick me in the side every time I look at them. I purchased a smaller refrigerator than I had planned because I was PROMISED that the refrigerator was designed to hold the milk in the door. The first thing that happened when I opened my brand new refrigerator was the shelf holder broke and the milk fell to the floor making an awful mess. They ordered the shelf holder assuring me it was a fluke and sent me on my unhappy way. After I got the part I installed it and crack-smash-pow-swoosh! It happened again! I called the store I purchased it from and they said they ordered extras so to come in and get them, that I had probably installed it wrong. Went like this and I finally told him like I told him at first I do no want this refrigerator! You said and the pamphlet says it is capable of holding a gallon of milk in the door. It does not. It cant even hold catsup bottles without breaking. Thats when he told me that yes, they were having an issue with this refrigerators door shelves. He then gave me the rest of the shelf ends he had and said after that they were gone, they had discontinued them. Also said I was past the days to trade my refrigerator. I told him that was because he kept stalling me, ordering parts. LEMONS AND LIES. Now the refrigerator sits in my laundry room, freezes food in either section on its own whim, and the shelves are held on with DUCT TAPE. I have multiple correspondence with the company but gave up as I was seriously hurt in a vehicle accident and had to put my energies to surgeries and healing. And dont get me started about the stove. I will not be buying Maytag anymore.

We had this washer 16 months. We bought it new from Home Depot. The clothes came out with spots on them, white residue and grease spots. This was ongoing for awhile. The bearings went out after 6 months. It was so loud now the water pump went out. I was told by Whirlpool (they bought out Maytag) that water pump is on back order and could take a couple of months!! To fix the bearings and the water pump was almost 700.00. A new washer is 1000.00. We junked it and had to buy a new washer GE. We are sick about this waste of money!!! What a piece of JUNK this Maytag Bravos XL is!! We need to have a class action suit and try to get something back. This is ridiculous and they arent taking responsibility. Whirlpool/Maytag are rip offs!!!!

I purchased this machine less than 1 month ago. Have had tech here twice - he cant find anything wrong with machine. As for large capacity it will hold a lot of clothing, but will not clean them. I have had to put less than a 1/4 of tub full of clothing (about 15 small items). Use high water level, extra rinse, then rinse and spin again to get the 2 tablespoons of HE soap off my clothing. Takes over 2.5 hours to wash about 15 items. I have called Maytag and they will not back their product. I purchased at Home Depot and they said they have to do what Maytag says. Sending another tech out in 2 more weeks. Takes more water, more electricity, and more time to wash clothes than ever before.

I just purchased this washer in Feb. 2012. The motor had gone out in Oct. I called Maytag Service, they came out to repair it. In Nov., it was doing the same thing again. I called Maytag Service, and they sent someone out to fix it. They expected me to take off from work where they inconvenience me with this washer. It is a reject washer. They would give me another washer and not consider people having to work and cant take off for their reject washer. They said as long as it is under warranty. I feel that I should be able to get me another. This washer has given me problems since I had it.

Under no circumstances should anyone buy an MMV4205DE or maybe any Maytag microwave. These units contain defective door switches and will fail within a year rendering the unit useless. The engineer that got the bright idea to protect us from starting the microwave without opening and closing the door along with the engineer that designed the defective switch scheme should be fired immediately.I purchased the unit March 2016 to replace a 10-year-old Maytag that had a failed magnetron, no problems ever with the door switches! This unit started to act up in Dec 2016 with the fatal open/close door problem, I am an EE so I opened the unit and checked the switches and found they were defective, replaced both for $80 and 6 months later the problem is back. I am buying another brand as I dont have time to deal with the problems with this unit. I now have the old white 15-year-old unit that I replaced years ago sitting on the counter to use while another unit is on order. Unit is heading for the landfill next month. Never buy a Maytag microwave, they all have the same problems!!!

I purchased a Maytag Legacy Series Quiet Series 300 in early July 2010. It had a recall for a heater part that could potentially burn down my house, so we couldnt use it while we waited for that part to be replaced. They offered me a small sum of money towards the purchase of a much more expensive dishwasher which I declined since Id only had the dishwasher a few months at the most. It is now the end of August 2011, a month past their factory warranty. The dishwasher did not get my dishes clean, made awful grinding noises and three days ago, it refused to drain and then spewed 50 or more gallons of water all over my kitchen which then leaked into the basement. The repairman charged $85 to tell me that the computer in the control panel had burned out and was not fixable. I think I paid somewhere in the region of $500 for this machine. My last dishwasher lasted about ten years. This is completely unacceptable. In searching the internet, I found hundreds, if not thousands of identical complaints. Clearly, this machine is a lemon and Maytag should be forced to replace it or better yet, refund the money spent to purchase the machine. Plus, pay for my valuable time spent mopping up water, washing dishes by hand, searching the internet for probable cause and potential solutions, waiting for Maytag/Home Depot to respond to my inquiries and a large sum for general annoyance. Maytag had a reputation of reliability (emphasis on had). Theyve got some slick ads but they do not stand behind their products at all. I will never by another Maytag product and I urge you to do the same.