Bravos XL Top loading High Efficiency Low Water Washer and Dryer - I gave this washing machine a 1 star but would give it a 0 star or less if the choice was available. I agree with everything others have voiced about this washer. I end up using the bulky cycle for everything because it is the only cycle I have found that will use enough water to get the clothes moving around. All the other cycles are a joke. First you must put everything around the wall of the tub away from the so called agitator. Then about 2 cups of water enters the machine. It then goes into this high speed spin. In my opinion it just pushes any soil deeper into the fibers. The drum will then spin slowly and water will spray on the clothes for several minutes but the washer never fills with enough water to cover the clothes. Watching it agitate through the glass top is almost hysterical. Laundry is barely moving. The high speed spin they push as a selling point puts deep wrinkles in everything and the wrinkle control setting on the dryer does nothing for them. It is absolutely the worst machine I have ever owned. My husband has repeatedly told me to sell these and buy another set. I will be ashamed to sell it to anyone. Im not sure how the makers of Maytag got away with selling these machines. I know there are different models but from what I have read they all work the same. I replaced a very low end GE Washer and Dryer with this pair and every time I do laundry I wish I had them back. The matching dryer is very costly to run as almost every load takes 2 cycles to get items dry. Nothing comes out completely dry even if you put it on the more dry setting.

This dishwasher has an electronic control panel that is faulty. Within one year of purchase, the control panel shorted out. It was replaced under warranty. Almost exactly a year after that, the same part failed for the same reason. This time, Maytag refused to replace it for free since it was out of warranty. A new control panel would have cost over $250. Disappointed with this Maytag product and their refusal to replace an obviously defective part, I decided to buy a new dishwasher from another manufacturer. Also, it did not make sense to me to spend that kind of money to replace a part that would continue breaking every year. AVOID Maytag dishwashers with electronic control panels!

Maytag is the worst washer company. I owned my washer for two years and I had two different problems with it and now I have a 3rd. The first was the same day they delivered the washer, I needed a wire harness. I should have returned it then but I didnt. The 2nd was six months after the first one. A wire came loose due to the washer shaking and the 3rd, Im not sure why it wont drain but the tub is full of water. I called Maytag and they really didnt care as long as they got their money. They referred me to three companies that fixes washer. Two of three was already out for this washer. If I didnt know any better I would think Maytag gets paid off for every customer they referred to these companies. I would never buy another Maytag Bravo or Whirlpool product. Im very dissatisfied with their Bravo washers. They lost a long time customer.

I am retired and have always had dogs in my life. My recent purchase of a new Maytag top loading washer has been very frustrating. There is barely enough water to measure in an oversize tub. The placard on the lid, and in the owner manual clearly show three levels of water. Each load takes twice the time as I am used to with my older Kenmore washer. I am forced to cut my loads in two or three, and use more water and energy to do a job that used to take less than half the time, water and electricity. I have had warranty repair to replace the control board twice, but nothing has changed. The repair techs both said there is one program on new washers, the knobs and settings do nothing, and recommended I get used to it. They explained the EPA is responsible for all changes to Protect consumers from harm. WHAT???I wish I had never bought this unit - if I could get my Kenmore back I would, in a hot minute! What a waste of a large tub to properly wash pet bedding and bedspreads/pillows, when there is only 3-4 inches of water! I wasted an entire paycheck, when I could have gotten my other unit repaired or rebuilt. I am seriously frustrated, I am searching for an older washer unit to get back to doing my laundry without being forced into a laundromat for pet bedding and larger items!!!

We purchased our Maytag 4000 series washer and dryer (Model: MHWE450) in December 2010 from Best Buy. For the first six months or so, we were very happy. We started to notice that the washer was getting a little louder by the month. I checked the level multiple times to be sure that wasnt the issue. Assuming it was just part of how the washer broke in, I just let it go - a bad move! Fourteen months after I purchased the set, the washer flooded all over the floor. I opened the washer and pieces of plastic were all over our clothes. After further inspection, the drain was completely full of the same plastic. I cleaned it all up only to find that the washer tub was so loose that it was banging side to side.I called Maytag to ask for help or suggestions. They basically told me that I was out of warranty and kind of out of luck. I responded that we do a total of four to five loads of clothes per week and that there was no reason that this commercial series washer should have failed after 14 months. They offered a one-time service plus extended service contract. Feeling that I had no choice, I spent almost $400 assuming that I had a fixed washer and a year extra warranty. I was told that someone would be out to look at the washer in three days. Finally, after me pressing and pressing, someone showed up a week later. He put a list together of all of the items that were needed to repair the washer.Two days later, Maytag service calls and says that the washer will be too expensive to repair and they would be giving me a reimbursement for buying a new one. They didnt have an exact amount yet. Two more days later, they finally called me with an offer of around $550 ($250 less than what I paid) based on their research of what I should be able to find one for and directed me to the website. One big catch though - it didnt include the $125 shipping charge. When I called to request for it to be paid as well, they declined with basically a “take it or leave” type of attitude. Not knowing what to do, I called every local appliance store until I found someone that had two in stock. When I went to look at them, I was told that both of the ones that they had were rebuilt because that model Maytag washer had a major issue with the bearing and basically needed to be replaced on all of them.Luckily, I was able to buy the washer and a five-year extended service contract for around $690. So in the end, I paid $799 for the new washer, $400 for a warranty, another $100 to replace the washer, and close to $100 in laundry mat costs for three weeks. I promised everyone that I spoke to with Maytag that I would write a review to share my story and thats why I wrote this. The repair plus warranty is a joke. I like this washer/dryer but will never buy another Maytag appliance again. Next time, I will buy extended service contract from the start.

I purchased this set of Maytag Centennial Washer and Dryer from my local Home Depot in Dec. 2011. I havent had a repairman come out yet, but I am extremely dissatisfied with them. The washer is a problem because it doesnt seem to fill up with enough water to wash the clothes. Also if you want to add something to the washer that you forgot you stop it, and go to restart it again, and it starts removing all of your soap and water again. This is a waste of money, if you cannot stop it and start it again without it filling up again. I would not recommend anyone buying this HE washer & dryer. Also the dryer seems to heat up too hot to me.

We bought the Bravo washer and dryer in 10/2009. Since then the dryer has never worked well. Weve had at least 8 service calls on same and the sensor doesnt work, i.e. says the clothes are dry when they arent and we always have to run them through at least two-timed cycles to make them completely dry. The washer is another nightmare. At least 8 service calls as well, and after one where the motor was replaced, it popped off and flooded my entire house. They laundry room is located on the second floor. I had to replace floors, walls, ceiling, light fixtures, etc. Insurance covered it but it never shouldve happened. Now the washer doesnt drain properly and the error code LD displays every load and we must manually drain it by either setting an extra drain cycle or take the entire machine apart and vacuum out the water. Each load takes twice the amount of time it should, if not more. But I guess its okay because the dryer takes just as long to dry a load of clothes. Something has to be done. Maytag is refusing to stand behind their products and it seems as though many of the complaints are for the same issues. Is there a lemon law for household appliances?

Ive only had my Maytag Bravos XL Washer for two years and I HATE it. It constantly gets off balance during the rinse and spin cycle. What should take 30 minutes takes triple the amount of time. My washer is in the basement and I constantly have to run up and down the steps to readjust the clothes in the washer. Ive started to just stand by the washer now during the rinse and spin cycle. What a waste of time. I would not recommend this washer to anyone. Also, it does an awful job of rinsing out the detergent and softener. All of my dark colored pants have detergent and softener residue on them after they come out of the washer. Ridiculous!

We purchased a dishwasher (Maytag) two or three years ago. We have had nothing but trouble with it. The welds on the upper rack broke. The wheels on the low rack keep falling off. Water leak happened recently. The start button broke. My wife and I decided to just get a new one rather than keep sinking maintenance costs which are going to keep adding up.

Maytags reputation for quality is gone. Our Neptune washer has had mold, door lock seized up and wouldnt open, and now our dryer drum is cracked. Exaggerating your products reliability is one thing - this borders on corporate fraud.

In April 17, 2015, I purchased another Maytag microwave but wanted the convection oven too from Home Depot. The convection fan quit working in January 2017. I called Maytag to ask how this was covered. Maytag only has 1 year warranty on parts and labor. So basically if you dont buy an extended warranty, you are stuck with a product that quits working. Apparently, Maytags work is only good for 1 year or they would have a longer warranty. I told the Rep this when I spoke to him. He told me they normally last 5-7 years. Wow, still not acceptable. He said I had two options. Maytag could send out a repairman and it would cost almost $300. The other option was just as ridiculous. I told him I paid almost $500 to start with and it only lasted 21 months. Of course he said if I had bought extended warranty it would have helped. If I paid $500 for an oven, why should I have to pay more to cover their bad workmanship?!! I am very disappointed in the quality and price of this convection oven. The bad thing is I bought all new Maytag stainless steel appliances in 2016 to match the convection oven. The products I replaced had been in my home for 12 years with no problems.

What a disappointment. I guess this is why we no longer see that commercial about the Maytag repairman being bored. Because now, he is out fixing these pieces of shirt. Im trying to fix my washer (Model: MAH8700AWW), what a sweet pain in the **. Dont do it. Throw it away if it starts making noise like an aircraft landing.

I have a two year old version of this dishwasher (MDB894995BB3) and now the start and cancel light on the control panel stopped working. I now see that this is a common theme with this model and I feel it is their obligation to repair these units with permanent fix and not the same thing that will fail again. I have 3 different Maytag appliances all bought 2 years ago from Home Depot and they are all broken. I will never buy a Maytag product again. I might replace this dishwasher as I know it will fail again. 2 years on a dishwasher is a complete failure. Unreliable Junk. Do not buy Maytag.

I really love my front loader and it has no agitator to rip pockets and tear off buttons. The tub is very large and I can wash king quilts. I do miss being able to fill the tub and put in additives and then add the clothes to soak.

I was told to at first to just leave the door open, then when that did not work I was told that I should bleach my machine at least once a week which I did. That did not work either. Then I was told to buy the product REFRESH and that would take care of the smell. That did not work either. So I am at my wits end with the stench of my clothes.

Maytag washer, top loader, Bravo series: We purchased Maytag washer and dryer 4 years ago. Last week, the washer started sounding like a 747 was landing in our laundry room. Maytag sent a service representative and informed us that the bearings were faulty and it would cost at least $800 to fix. It is appalling that a 4 year old appliance should fail like this. We will buy a different make and we will never buy any Maytag appliance again. This is such poor quality and worse service. Maytag would only offer a 30-40% off a washer, but only if we bought it directly from them. We can get a better offer from any local store. They also said we could get a discount on the part we need, but not the service. Do not, I repeat, do not buy Maytag anything. You will regret the purchase.

We purchased this Maytag washer. My wife liked it at first, but after a few months she kept complaining the wash stinks, and I can also say that. I complained to my wife about the smell of our wash, especially the wash towels. The wash was turning colors and some we threw away. My wife has been complaining about all this for months and years and said she will never buy another washer like this. Then about two years ago, she was having trouble with codes coming up. We called service, but didnt get any help, so I looked on internet and found the problem with the code. I took the washer apart and cleaned the tube out and the washer worked, but every now and then my wife needs to climb over washer and unplug, let sit, then replug back in and start it to get rid of code. My wife and I are very upset with this washer!

I purchased a dishwasher model #MDB4709PAM from home Depot in March 2014. There is something wrong with the electrical and it is shocking people if you touch it. Just so were clear.. MY DISHWASHER IS ELECTROCUTING PEOPLE... Called Maytag repair because hey its only five months old. Cant send anyone out for three weeks.... three. Took an hour on the phone because I had to talk to four departments. Kept asking if anyone had been hurt seriously or property damage, so they made sure their butts were covered, sigh..... Should have bought the LG.

I am a WWII vet. I bought a Maytag dishwasher 4 years ago from Home Depot... Cost me $600 in total repairs. Maytag would not help. My son just brought it to the dump! At that same time I bought a Maytag bottom freezer from Home Depot... It has never worked right. Ice dispenser broken after 1 year, food freezing in fridge at any temperature... It just died! Maytag refuses to take any responsibility for THIS POS!They should be ashamed at the way they treated me. I am 94 years old, and have fought for our freedom, and was looking for one simple thing from this American company. Its called fairness! Maytag sucks! You have lost a lifetime customer. You have lost my son as a customer, and will lose anyone I talk to, as well as my son posting on ALL social media! SHAME ON YOU MAYTAG! SHAME ON YOU MAYTAG!

I purchased the Maytag Bravos XL MVBW755DW Washer and MGDB755DW Dryer in July 2016. Shame on me for not making my complaint sooner. They offer the Tide Pods for use but they dont completely dissolve and leave a residue/stain on the clothing. I have to wash everything on Deep Water Wash just to try to get them to come clean. Clothes will come out dry in some spots, they will have fabric softener stains on them, the pre-treated stains are still there once washed. Lint residue will be left on just about every piece of clothing. The fabric softener/detergent dispensers left side is rusting and I have to pull it out and clean it once a week. I cant get to the track on the inside to try to clean it and soon that will deteriorate and the dispenser will no longer slide into place. If I could attach pictures I would. Now moving on to the dryer, it dries clothes great. My only complaint at this point is that when the cycle is getting ready to shut off it sounds like a jet engine and rattles terribly. To sum this up, I called customer service this morning. They said nothing that I am explaining to them sounds as though it is a manufacturers defect. They said they will send a tech out to review at a fee of $99.95 plus the cost of any labor associated with the repair. They did however offer to pay for the parts. Now my question to them is if none of my issues are a manufacturers defect then why would you offer to pay for the parts? The unit(s) are no longer under warranty... Think twice, gather as much information as you possibly can prior to making a major purchase. I DO NOT RECOMMEND THIS PRODUCT!

Im very pleased with both the washer and the dryer. The front-load washer is very efficient with many washing options dependent on items being washed. Spin cycle spins very well which lessens the dry time of the washer.

I have on the Maytag dishwasher for about a year. Is very quiet, the dishes are not clean. I called three repair guys from Maytag. The first time they replace the pump. Second time the guy said he just had a designed machine is no good.

Purchased dishwasher Mod # MDB7749SBM1 thinking it was Maytag (lonely repairman) in June 2013 from Home Depot. Cost new over $1,000. As of March 2016, three service calls, two of which required replacement of the control panel. Now the control panel has failed a third time and we are told by Whirlpool (parent company of Maytag dishwashers) they will not cover the repair. They have offered a discount for a new dishwasher. Since that did not seem like a very good option to me, they offered to let me pay for current service plus a year for over $350.00. I was sad to discover that they are the manufacturer of most dishwashers available at your local home store dealer (Whirlpool, Maytag, KitchenAid, Jenn-Air, Roper, Amana). VERY DISSATISFIED CUSTOMER!!!

My dishwasher is 9.5 months old. The computer board needs to be replaced and they cannot find the part. It’s been 2 1/2 weeks since I called in the repair which is under warranty. I was told they have 10 business days to search the country. Really search the country. Does anyone know what will happen if they cannot find the parts I need?

MCT commercial technology washer Bravos XL - HORRIBLE product, NEVER worked right! Maytag misrepresented this washer. DONT buy it! Lie after lie! Its suppose to be high efficiency... conserve water and energy. I have to use 3 times the amount of water and energy because it doesnt wash the first time correctly. Leaves soap in clothes, just doesnt wash properly. I have done EVERYTHING they have recommended NOTHING works! I will NEVER buy another product from them. Even the repair people and Customer people say they have nothing but problems. Im going to small claims court. Im sure with all the problems we could get a class action lawsuit. No stars.

I own a MAYTAG BRAVOS XL* TOP-LOADING HIGH EFFICIENCY LOW-WATER WASHER. On 9/1/15, after reporting a problem, a service person arrived to assess the problem. His diagnosis led to a second visit on 9/8. On the second visit he replaced multiple parts, assuring us that the problem was fixed. When this proved to be false, we called for a third visit; this time a different person arrived. After disassembling the washer he found a large hole and another cracked area in the inner plastic portion of the tub. We made a fourth appointment for repairs, receiving assurances that it would be repaired at that time. I received an e-mail today (9/16/15) informing me that an additional 7 days would be required to arrange for delivery the required part. In the interim, my wife and I are forced to use a local coin operated laundry about every three days, totaling 7 visits at approximately $25 and 3 hours per visit before the next scheduled appointment. The compensation offered, 9 months extension of the existing warranty is woefully inadequate. I want the appliance replaced, as history has taught me that you are obviously unwilling or incapable of repairing it correctly in a timely manner. Additionally, I want the initial warranty that accompanies a new product extended to a full 3 years. We have paid out over $150 and wasted 18 to 21 hours of our time unnecessarily. I expect compensation for the funds spent as a direct result of the bungling, incompetence of your service staff. My questions are these: 1. Was the part defective prior to installation? 2. If so, why did the representative not notice it and refrain from installing a broken part? 3. Why was there no mention of the damage on the first visit? 4. If not, how did the damage occur? Did the service man damage it and fail to report it? 5. What caused the delay in obtaining the part? I have other questions, but will no longer spend any more time on this debacle. I cannot honestly say which is worse, their quality or their pathetic version of customer service.

Does not clean laundry, leaves dry untouched spots, all my clothes look unwashed & the rinse is terrible, leaves dirt on clothes due to little water in cycle. Im a senior on fixed income. I cant buy another machine.. I called Maytag within a couple of weeks of using washer. They told me We have No guarantee for Customer Satisfaction. This is a complete scam on their part. If I could of afforded a Lawyer I would of taken them to court. They knew what they were selling & somehow got away with it. Give the people what they pay for, not the Bravos piece of Junk. Can only wash on 1 cycle to get wet wash. But paid for other useless cycles. Who made this machine & who allowed it to pass to the unfortunate Consumers. If anyone can help getting Payback from Maytag, Please let us know... Better business Bureau should get after them.

OK, LAWYERS -- Where are you?!! You have a lot of very unhappy people who feel they have been justifiably TAKEN! Whirlpool needs to replace these refrigerators with another brand! We bought same bottom freezer Maytag refrigerator in 2010. Luckily, which we dont usually do, we purchased a five year warranty plan. Within six months we noticed the rubber seal on our refrigerator on the french door part was turning yellow and then getting darker. We feared something was burning the rubber. A Maytag repairman looked at it, called Whirlpool, told them that there werent enough parts to fix this refrigerator. Whirlpool asked him what they should do and he told him it should be taken out on the front lawn and burned (yeah for that repairman)!! Whirlpool agreed to replace the refrigerator with one, very similar but a new model #. Thank heavens, after our insistence, the warranty was extended to the new one. Now after about three years, we are having the same problems that all of you are having with the next one.. Our Home Owners insurance adjuster just gave us a settlement to have all the ceramic tiles removed, which are cracked in almost two dozen places, and whole floor replaced (minus our $1,000 deductible). The floor was put in new three years ago. The refrigerator repairman is next to come out. From what I have just read about all the complaints on this refrigerator, NOTHING is going to fix this problem short of replacing it at our expense. My advise to everyone --- FIGHT THIS. Write to Whirlpool (not Maytag -- Whirlpool owns it), and blast them over and over with letters and complaints and threats of lawsuits. Why should we be taken for that amount of money while Whirlpool does nothing but keep it. A class action suit is badly needed. Big corporations should not be able to take people over like this and get away with it. If it takes a lawyer willing to take on a class action suit, this is it! In the meantime, bombard Whirlpool with letters and dont stop! It takes persistence, but in the end -- most of the time, we will prevail. Big companies hope we will give up and go away. They count on it. Dont let them win!!! I have had a Maytag washer and dryer for twenty years with no problems. Problem is that Maytag doesnt exist anymore -- who is making this....?

Bought the pair of Maytags on sale at Lowes 6 years ago. They are commercial grade and wash everything. Have had no issues - works every time. It took a while to get used to not have an agitator but now it seems natural. Would buy again.

I purchased my Neptune Washer in 2005/2006. I had a mildew problem, and the store told me to clean it with bleach. It is now 6 years later, and the ball bearings are going out. I called two different repair companies, and were told by both they would save me the call out charge, because the ball bearings were going out, and it would cost between $ 600-$700 to fix, so I may as well buy a new one. The washer is only 6 years old. This is completely unacceptable! I then tried to find someone online to fix it, and I ran into the fact that the Neptune Washers had a recall. Why was I, not notified? I bought the washer and dryer set from a Maytag store. No one tried to reach me. I am now stuck with the problem of buying a new one, and really cannot afford one at this time. I went with Maytag due to the brand name, and I knew it would be reliable. Is the joke really on me? Can someone please call me, and point me in the right direction?

I wish I had found this website before I bought my new Maytag washer and dryer from Home Depot on March 7, 2018. I replaced a 30 year old Maytag washer that I should have kept. I wash two loads a week so has not been used that much and now it will not drain. I tried everything, canceled the cycle out, checked the circuit breaker, unplugged it, removed the clothing, bucketed out the excess water, tried the drain and spin cycle, etc. Just will not drain or spin. Repairman is coming next week... Still under first year warranty but if it is not the “fault” of Maytag I was told there will be a $90+ minimum service charge.

Just purchased a Maytag French Door Refrigerator and am I sorry I did! Very noisy and runs continuously. Maytag says it is because it has high-efficiency compressor and fans? How is running continuously efficient? The continuous noise actually keeps me awake at night. Not sure what to do as I have spent $1700. :(

Is there any place to give a zero to this Maytag Front Load Washing Machine Model MHW5500FW1 and if there is a class action lawsuit please include us! We have owned other Maytag Washing Machines and never experienced such an epic failure as we have with this washing machine! We were so excited when we purchased our new Maytag washer/dryer set in March of 2018 we even remodeled our pantry/laundry room to accommodate them! As the chief operator of the washing machine, I have literally cried at what a mistake weve made! We have no complaint of the Maytag dryer. Let me describe my new normal procedure for laundering a load of clothes. First, load the washer with clothes then press power/cancel then press rapid wash let the clothes get HOPEFULLY saturated with water then hit hold to start and then hit power/cancel this shuts off the washing machine. I then press power/cancel again and select normal and the water empties out of the washing machine from the prior load and then starts to refill, if the add a garment light comes on (when it wants too) and no I dont change any pre-set settings I am able to add extra water with a pitcher, if this procedure works I let the washer run its 1-hour and 48-minute cycle. If not, I have to start over again because the add garment light wouldnt come on to allow the door to unlock. After the clothes are finished I again press power/cancel then hit rapid wash put my fabric softener in the dispenser press hold to start and let it run its 36-minute cycle making sure my clothes are rinsed appropriately and not stiff because of the lack of water. I neglected to say that when Ive tried tricking the washer and think I am able to add extra water, if Ive added too much the sensing kicks in and the washing machine drains all the water out on its own and refills with the little water it allows! Which is maddening! I throw up my hands and sit down and cry!!! I have contacted Maytag/Whirlpool complaining about the lack of water and their wacky water sensor! I asked them how can you conserve water and electricity when you have to wash your clothes over and over with long wash cycles? This doesnt make sense! My white clothes are now dingy and stiff as well as the colored. Maytag says you can use powdered detergents if its HE High Efficiency powdered detergents, but thats not true. The detergent doesnt dissolve and ends up on the clothes at the end of the long wash cycle because of the lack of water! From the beginning I adjusted the amount of powdered detergent for the front load washer and have to dissolve it in hot water prior to washing and hopefully am able to add it to the clothes if the add a garment will let me! I have now resorted to extra cycles to rinse out any remaining detergent hoping my clothes will be soft and fresh smelling. I had planned to replace my old Maytag agitator washing machine with this piece of junk front loader, fortunately we kept our old washing machine as a back up!

My Maytag 2000 has ripped our clothes. This is my 1st front loading set. I looked on the internet and it seems that this is a known problem. Very upset that a brand that I had for 30 years and recommended to others as well has turned into a terrible company. Im a single mom and Im not in a position to replace a washer every year. I trusted Maytag! A recall and either replacement of the parts, or delivery of new part to fix the problem should have been put in place. I wrote to Maytag to see if they will do something to fix this problem.I have the set, washer shakes a lot, but works well. Washer also always has a lot of water left on the door seals folds, terrible design... I will post on other sites to warn other customers. This is not OK, my clothes are destroyed. See pictures. Clothes got trapped in a gap that exists in the perimeter of the opening, where it meets the door. Why is there a gap at all???

Purchased Maytag washer 2014, first the porcelain in the tub chipped then 3 years later the control unit assembly and actuator went bad they wanted $464 to fix the machine, more than we paid for it. The dealer tried to sell us insurance for this product at a hefty price, I believe all manufacturers are making their products with a short lifespan and the way for them to make money is by not making a quality product like they used to do that lasted 25 years or more, the only washer out there that is dependable is speed queen made in the USA in Wisconsin.So we the consumers are the losers in buying washers that do not live up to their name, Maytag covers themselves by a warranty of one year period for parts and labor and if you do not buy the extended warranty at a hefty price you are out of luck - so my advice is when buying a washer read all the reviews and make your decision, but the best advice is buy a speed queen online for $600 and save $400 by doing that and get a quality washer that will last 25 years or more.

Went from an old simple Maytag to newer model, but still somewhat basic compared to others. However still getting used to the water saver feature in that getting in the right amount of detergent as not to have it set on my clothes and having to put through another rinse cycle and a more slimmer agitator. But do like the Maytag brand.

I dislike Sears and more so Maytag. I bought a Maytag Bravo XL MCT. It worked nice with very few hiccups until 1 1/2 years old. Then the washer went to the lock and done mode, thought it might be the lid switch down the washer up. Looks like I would need to change out the whole panel. Its not worth the trouble OR time to put one dollar to repair the piece of **.

The low water usage design is horrible. Clothes dont get clean as it doesnt use enough water to cover them. Takes twice as long to do a load as our old washer. Took about 1 1/4 hours yesterday for 1 load using heavy which is the only setting that uses more than a thimble of water. Should have looked for a commercial type with a real agitator and adequate water usage. Not saying Maytag is probably any worse than any other brand of new efficiency government mandated garbage washer, but its no good.

I purchased the gas stove in June of 2012 from Home Depot, along with a Maytag microwave (Model MGR7662WB4). Home Depot installed both items. After trying to reach into the microwave about the stove, the knob would turn itself on with me brushing up against it. This happened several times, and one time the flame shot up and I almost got burned. The last time it happened, I did not realize that the knob was turned very slightly and gas was coming out of the burner for several hours. If it were not for a friend stopping over, I would not have considered the odor being from the stove. I assumed that the drains were probably backed up and started to add cleaners to the toilet bowls. I had to open the windows for several hours to get the smell out. So I called customer service 2 times. The first person said I would have to pay for the call if the problem was not Maytag and I said, “Forget it.” Then I went into Home Depot and the salesperson in there gave me another number to call for service. They came last Friday and said that he had seen at least 10-15 calls about this and since the unit was working as designed and no recalls, there was nothing they could do. “Just wait and see if a recall would be put into place and I would be on the list to fix it. In the meantime just keep the knobs off (which I was doing already out of fear).” My sister just bought a Whirlpool gas range this summer as well and asked if I could try her knob and it worked perfectly. Again I called CS and was told they could not send me those at no charge and that it would cancel out the warranty. So I asked her what I have to do before I or someone else gets injured and she said that until there was a recall, there was nothing they could do. I told her I was going to contact Consumer Report as well as Pam Zekman on Channel 2 news in Chicago. End of story; I still have the problem and no knobs on the new stove. Anything you can do to help please contact me, and thank you in advance.

Maytag bottom freezer / refrigerator: What a low-quality operation these guys are operating. We have a 5-year-old double door unit, which is not a cheap ticket item; and we thought that Maytag was from the days of old. The compressor failed along with ice makers and some high-use parts inside. I can understand the plastic lids and guides wearing out with heavy use, but not the compressor. I called Maytag and was directed to their proud Tennessee Service Location. It might as well be in China, where the real owners are located. She said, Oh well, we build quality units that are to last 12 years. However, they are man-made, and you cant count on that being a positive thing. What arrogance. I might get stuck with another brand from Asia. But it will never be a Maytag or any other in their family of products. The repairman is really busy these days.

I bought a Maytag electric stove steam lift oven 2 years ago, I regret it. I baked a pie, and used the steam cleaning, it didn’t clean, my oven is still dirty. The top of the stove is not easy to clean and scratches very easily. It’s not my first stove, different brand, and I never had problem like I have now. I should have stayed with the brand I had before. My other regret, I should have read the reviews.

I bought a Maytag dishwasher from Home Depot in February 2012, $700. After a few months, the buttons stopped working and the machine was unresponsive. I called Home Depot and they fixed it under the warranty. This continued to happen every 2-3 months. After a year of dealing with this, the warranty expired and I had to purchase the manufacturer extended warranty with Maytag, $240 for 5-years of coverage. The problem continued, and every few months, the thing would stop working and I would have to call for service - 2 to 4 weeks without a dishwasher waiting for service appointment then parts and another appointment for the repair.Perhaps my machine was just a lemon. I dont think they make that model anymore. Heres the number so that you can avoid a three year headache of a machine, MD87749 AWM2. I will say that after MANY agonizing phone calls with warranty company, after 2 years of ongoing service calls, they eventually issued me a check to replace my lemon.

I purchased a Maytag Bravos XL washer mid November 2013. Less than six weeks later it leaked water. The repair person has been to repair it four times. The last visit was yesterday. It now has more problems than it originally had. It still leaked water. Maytag does not stand by what they sell. All they say is they will repair it. My caution to anyone reading this is never buy a Maytag appliance. I hope this review helps someone in their decision making process.

This Maytag refrigerator is a counter depth so a little smaller in the Inside than I would like but fits in my tiny kitchen great. It has an inside water dispenser which is so nice because it keeps the clean look on the outside. It’s a year old and so far I have not had any problems with it.

This machine(Bravos XL Washing Machine) was highly recommended to me at the Home Depot by a sales associate. I broke down and took the recommendation. Oh how I regret that! This is a terrible washing machine. It does not put enough water into the machine to even cover the clothes halfway. It ties the clothes in knots! I made a terrible mistake when I purchased this!

The machine will not fill with enough water to wet all the clothes. I have to tape the tub to trick the machine so that the clothes will all get wet. When I had a service look at the machine he said that is how they are designed to be energy efficient. Who does not getting all the clothes wet clean them??? This is not for big loads but ALL loads - even hand wash loads. Every load takes an hour plus. Less water, more time, unclean clothes. I lose all the way around. REALLY wish I had a machine with the old features.

I purchased a Maytag washer-dryer combo in late July 2014. It wasnt until early August that we actually used the washer. It worked fine the first day, but the next day it would no longer fill. After following all of the troubleshooting instructions, I called Maytag to schedule a repair. They said they would locate an authorized tech to make the repair. I called back the next day and was informed that there was no repairman in my area and they would contact a service that contacts local repair techs. A few days later I called back to learn that they still could not locate a repair tech. I live near the New Mexico/Arizona border, and asked if a service tech could travel from Tucson, Arizona and was told that they could not cross state lines and, at that point there was nothing else they could do. They claim that I live in a remote area, but I reside near a major US Interstate (I-10). I will be filing a complaint with the BBB and my states Attorney General. It is now late October and all of my efforts have been ignored. I am totally disgusted with Maytags customer service.

I purchased Maytag washer and dryer on 12/6/2011 and they required four repairs of the same problem. The bellow and rubber seal continually break and rip. Same issue all four times and Maytags response was to get a second opinion. Okay, same issue and same problem. Maytag does not warranty their machines for a full year and have yet to solve the problem with the machine.

Purchased less than a year ago, Machine stopped working. Approved service company says no error codes visible must be ok. Machine still does not work month later, service again does not show up for call, following month same. Its still in warranty but they claim it is fine. Error code disappear right after popping-up no storage of error codes.. I had to buy small washer to manage home. Really bad choice of product. Will not use this brand again.

Paid $900 for this side by side stainless steel model 15 years ago. Pros: performance, appearance, simplicity. Cons: none. Only 1 minor repair, and the repairman said this is 1 of only 2 makes he recommends.

Purchased what was supposed to be a good dishwasher. In less than 3 years the control panel went out. It would cost more to replace the panel than to buy a new dishwasher. I will never buy another Maytag product.

We had the same problem that everyone is complaining about re: frozen water in bottom of freezer dripping out onto floor. Swore when I got rid of the Maytag smooth top stove that broke after 5 years that I would never get another Maytag but broke down and bought this fridge. Maytag rep made it clear that the Fridge had a NOTE on file about the drain, but it was NOT a product recall. So after virtually taking the freezer apart before the repairman came, we ended up paying $120.00 for the repair, not the part. Yippee. Please note that the repairman told us we saved a lot of money by taking apart the freezer so most repairs probably cost a lot more than ours.

Purchased a Maytag Bravos washing machine. DO NOT BUY THIS MACHINE. Disaster as the cycling is hit and miss. The clothes can take 4 hours or more to wash a load. And even then the clothes may still be soaking wet. Grandmas old wringer washer was better. DO NOT BUY MAYTAG. DO NOT BUY MAYTAG BRAVOS.

Mine is the Chrome Maytag four-burner cooktop model. About $700. I installed it with ease. After two years there are only one or two slight scratches. It sees full meals for two cooked daily. The grate is first class and looks new, the top itself is easy to clean with a damp soapy cloth and mineral oil. There is easily enough BTU power for any size of pro pan. The igniters are healthy and fine and a repair would be easy.

I am angry at my Maytag! It sprays water on clothes that is not enough to soak them or let the detergent to be dissolved especially for towels. Hopelessly, I Hand Wash my towels, rinse in tub then just put them in the machine to spin. BAD BAD :( :( Is it possible to increase the water amount?

We purchased a TOP of the line Maytag dishwasher with the expectation that we were also purchasing high quality. Boy, were we wrong. Continuous problems with the controls since out of warranty. The controls are in the door and operate pushbutton from top. This is electronic pushbutton not actual pushbuttons.MDB89595SBS.

This washing machine worked great for just under 3 years. I noticed it wasnt draining completely. Per my appliance repair guy, the bearings were shot & it was going to cost over $300 to fix it. Called Maytag because my owners manual stated I had a 10 yr warranty. Wrong. The warranty only covers the wash basket & the drive motor. Look on Maytags Facebook page & you will see pages & pages of complaints on all of their appliances. Refrigerators, washers, dryers, if its got a Maytag name on it, its broken. Many of these appliances worked for only a year out two before they bit the dust. I went to Maytags fb page & ranted about their poor quality products & Maytags refusal to stand behind their products. Know what happened? They sent me an email stating that theyd reviewed my case yet again & there was nothing they would do. Then they blocked me on fb. Yep. Please please before you buy any Maytag/Whirlpool/KitchenAid product, please dont! Save your money & buy another brand. All Maytag will do is send you a form letter telling you they understand your frustration & you can email them your info, theyll investigate & get back with you. When (if) they respond theyll tell you theres nothing they can do. Basically you are sold, too bad, so sad. I now have a $600 piece of junk sitting in my garage. Im hoping I can get $20 out of it from the scrap yard.

Maytag Centennial Washer MVWC400XW2 - Bought this washer Fall 2011 -- first 6 months had to be serviced and now (February 2016) needs to be serviced again - has not cleaned my clothes for the last 3 months. Now, I have had to order a new washer - you can bet it wasnt a Maytag. My new washer will not be delivered for another 3 weeks. Past the part of not cleaning clothes, now it wont even empty the water, or pump out the water. It makes a horrible noise! Before it wouldnt use any water, now, it fills completely up. I do not know if it will make it through this current load much less another 3 weeks. Always bought Maytag before BUT WILL NOT AGAIN - after what I have been through with this washer!

I would not buy a Maytag again. I am very disappointed with the noise level this dishwasher produces. I am also not happy with the inside capacity. I never have enough room for all the dishes when I have dinner parties.

The bottom oven of my Maytag double oven range (serial #MER6765BAS18) caught fire while I was baking there. The coil burnt out and separated. This did not occur due to food spill or other means. The coil was charred. The stove top does not perform adequately and the coils do not heat uniformly.

Our washer, still under 5 year parts and labor warranty, wasnt functioning properly. We went through proper procedure having repair personnel first attempt to repair; waited over allotted time for replacement parts, wanted to attempt to repair again, then to replace with sub-standard model. We are now in our 5th month of being told 3-5 business days, 10-14 business days, and I was just told it will be weeks (after waiting 19 days) that replacement will return our call as they are 4 to 6 weeks behind. I have pages documenting dates, times, names, departments and excuses. What can I do at this point? What are my options?

I bought this wash (XL HD) 1 1/2 years ago. From the time the people installed it it never worked correctly. I have never wanted to beat up an appliance before, but this washer makes me so mad that I am ready to just throw it out and buy a new one even though I paid 600.00 for it and it was more than I would ever pay for a washer. I bought this so I could wash my comforters mainly. Well I cannot wash comforters unless I wash them 5 times or at least try to wash them 5 times or more. They get unbalanced and then the machine shuts off. After doing everything from changing the hoses like somebody else suggested, it still didnt work. Along my troubles with trying to rinse and drain I did find something new that I didnt know I could do for all these months is when you put your machine on rinse, spin, dry and the extra rinse light pops on, click it and turn it off, then it reduces the spin time to 15 minutes instead of 26. Also now I have to just let my hose drain on the floor of my outside wash room because if I hook it up through the wall to drain outside it just stops with the LF code. So I have 2 inches of water on my washroom floor and it really sucks. This is the only way I can get the machine to work without turning itself off. Very disappointed with this machine that appears to be so large (looks can be deceiving). It cannot wash hardly anything and this machine should be taken off the market. It is garbage. I really wish this did work because I have spent too much time trying to rewash, respin, get all the water out of the clothes so I could dry them. This should be banned and not sold by any store.

When we first purchased our fridge, I was super excited. I have read the numerous reviews regarding ice in the bottom and the noise. Ours is noisy also. Nothing I cant live with. Now ice on the bottom. That doesnt work for me. A friend of ours told us the drain was plugged. Not that the doors needed to be replaced, nor does it need gaskets. All you need is a hair dryer and a man like mine who can build or fix anything (honest to God that is the truth). He took the drawers out and then removed the door to the freezer. In the center on the back of the fridge is a drain hole. Aim a hair dryer in this spot and it will melt the ice which is plugging the drain. Ours took about three years to have the water in the bottom issue. Since we have now seen where the drain hole is, there would be no need to take the door off and the drawers out. Now, one other preventive measure. Take off the lower back plate of the fridge. At the beginning of the drain hose is a rubber nipple. There is barely any room for the water to drain. We cut the end of the nipple off in order to make the water drain better and less likely to stop up. We just snipped a bit of the end. The reason it is designed like that is to prevent air from coming into the. Just a small snip. I hope this may help some of you. Tell the Maytag repairmen how to fix it.

Bought this machine last spring with high hopes. When I noticed issues, I looked up other reviews and saw so many having the same experiences. It does NOT use enough water to clean or rinse the clothes. My clothes are getting stretched and worn. I have to run extra rinse cycles to get the detergent out of my clothes. For the cost of this machine, it should be working much more efficiently than it does. Not seeing any savings in electricity or water bill due to extra cycles needed. Waste of time and money. Would love to join a class action suit against them for the piece of junk!

We purchased our Maytag Washer back in August of 2019 and already needs a Motherboard and Lid replacement. Not only do you have to wait almost an hour to get a hold of their customer service I got hung up on once after waiting that long and the a Customer Service Lead by the name of Brittany couldnt offer any help either. We have been without our washer for almost a month now and will have to wait another couple weeks for the part to come in on top of probably another week for a maintenance person to come out and repair. I asked to expedite the part but that went absolutely nowhere. It actually added time to get the part because it was suppose to be here on the 13th but now its up to 9 business days for that to happen. I would stay away from purchasing any appliance from Maytag with the experience we have gone through and terrible customer service as well.

I bought a set of 4 Maytag kitchen appliances. Terrible quality. Dishwasher racks poorly designed for anything except standard size dishes. Microwave has a hotspot and explodes whatever Im reheating. But refrigerator is the worst. According to my service man, Maytag is aware of known issue with poor quality evaporator coils that erode quickly, leaking freon. Causes problems with ice buildup in freezer, poor ice production until it loses enough freon to stop chilling correctly causing food spoilage. Im to that point now. This fridge is only good for offshore fishing site. Whirlpool is aware but will stall as long as possible, then refuse replacement, but they will offer to help you replace the appliance. HA! Fool me once, shame on you. Twice, shame on me.

I bought a dishwasher from Maytag model #MDB774SBW0, in 2013, last year prior to the year warranty it broke. The control panel had to be replaced. This year its broken again. Control panel not working properly and its starting to rust on the outside in the corner. Per the company unless the repairman damages it out theres nothing they can do. I cannot believe this piece of junk. First of all it costs so much and has broken twice for the same issue in 2 years. Will not buy another Maytag, very unacceptable.

I purchased a Maytag Neptune 24” front load washer (MAH2400a) and 24” electric dryer (MDE2400AYW) on October 26, 2005 from Sears in Chesterfield, MO. In April 2011, the drum in the washer began to slush and grind. Water also began pooling around the machine. I called Sears and arranged for service repairman. Before he even looked inside the washer, the repairman wanted to give me a coupon for $50.00 off a new washing machine from Sears. After my insistence, he finally opened the washer and told me I needed a new drum. Because of the Sears repairman’s reluctance to look at the machine, I had another appliance repairman review it and was told that the water pumps for this model were defective. Any loose items the size of coins collected inside the pump and damaged it. I paid $340.00 to get the pump replaced. Ten months later, the dryer started smoking. After scheduling a service call, I was told the heating element burnt out and it would cost $360.00 to replace. It was then I noticed that the washer was leaking again. I took the front base cover off and saw mold growing under the machine. A little research uncovered that this set of machines has had many dangerous problems, from mold to catching on fire. There was a class action lawsuit filed and won by consumers in April 2005, yet I was sold this model in October 2005. I feel both Maytag and Sears knowingly sold me a defective and dangerous product. I would like to be refunded for this set.

Our product was purchased with our Condo. We have had it for 6 months & the first time I called someone was for the oven door being so terribly hot. I was told that was normal. Then I tried the cleaning of it & you would never know anything had been done. It would take a heck of a lot of elbow grease to get the marks off & I dont have the strength or time to be doing that. I had someone come again & he said to do it again, which I did & it still was not clean. I have done it a 3rd time now & still no better. I think this product is a total piece of junk & would not recommend it to anyone. I am a very unhappy customer & will never purchase another MAYTAG product.

My microwave will not work when the door is shut. It says: Door open. It’s worked intermittently, doing this for about two weeks. Then my husband woke up one morning a week ago and the microwave was on like it was running, light on but the plate was not turning. So we’ve had to unplug it and do without during thanksgiving weekend. This seems to be a common issue, obviously from the reviews below, so shame on you Maytag for not owning up and doing the right thing, covering repairs or sending out a recall. It’s a $112 service call here locally plus parts and labor. I will certainly be telling others not to go with Maytag. Maytag is lucky- it turning on by itself AT NIGHT, WHILE WE WERE SLEEPING, that it did not cause a fire or something. I’m pretty upset that it’s inside a 2.5 year window and already has issues.

I purchased a Maytag washer 5 months ago. I noticed the washer was not putting enough water in the machine to cover my clothes, and at the end of cycle my clothes would be all tangled up. A repairman looked at it and said there was nothing he could do. Do not buy this washer. It is a lemon. I even spoke to the main customer service representative, he was the most arrogant man I have ever felt with. He basically said deal with it. I want. I want my money back so I can purchase a washer that actually works.

Im currently standing in front of my washing machine waiting for the 13-minute drain and spin cycle to finish because once again my load didnt drain and finish right. Except it has already been 40 minutes and it claims there is still 9 more left as it continues to sit there doing nothing while it hasnt even started spinning yet. It Sat on 13 minutes while sensing for over 5 minutes, then 12 for 10 minutes while doing nothing, then it changed to 11 minutes and made some weird noises but didnt actually do anything for 15 minutes, and now the timer randomly changed from 11 to 9 without any noises or movement happening and now continues to sit here.I stupidly thought I could spin my clothes real quick to throw them in the dryer before bed and now I stand here extremely tired and very irritated. I also have no doubt some of the clothes will have holes in them when theyre done because they always do, my family looks like were homeless and ratty half the time we get dressed now. Also it never deep cleans thoroughly even on the toughest settings, I swear our socks can be washed 3 times in a row after being soaked all day and still come out crusty or a lot of times the armpits of shirts will still smell or be ultra stained with deodorant marks still.This technology is almost too advanced and everything is decided by sensor, regardless of the registered functions on the buttons it will still do what it wants as the sensors see fit and run when they decide everything is perfect and ready, including taking 10 minutes just to unlock the lid when you pause a load cuase a small child may drown in the foot of water or a person may have their life completely altered by getting a little bit wet if the machine isnt completely drained and in pristine condition before you open the door. This machine is terrible. This company is terrible. And worst of all they drain your wallet for these horrible contraptions. I wish I could rate this 0 stars.

This washer had good reviews when we bought it, but now today the agitator is not working. I see there are now 100s of bad reviews of this machine most around the same 1 1/2 year mark. How unacceptable to have a large appliance like this break after such a short time. Ive called Maytag to see if there was a recall and there is not. They offered the extended warranty to me for $325 that would cover all parts and labor. Ridiculous.

I purchased MVWB955FW (washer) and MEDB955FW (dryer) from AJ Madison and the units were delivered in December 2017. After using the washing machine 5 times the glass lid spontaneously shattered putting glass into the machine and all of the clothes. I called Maytag for a replacement/service and they had to reschedule as the lid wasnt in yet. A week later, I followed up with Customer Service only to find out that the replacement lid was also shattered. They didnt make a replacement lid without glass (not sure why you need to watch the clothes being washed). I was told that there were no replacement lids available anywhere. I asked about getting a replacement washer and was told couldnt do that.I asked them to pick up the units and refund my money, which they promised. It is now 2 months since the original call for service and I continue to have to follow-up with them (never get a call back) and STILL have the broken units in my house. I have since purchased a replacement set (LG) and waiting for my refund. I will NEVER do business with Maytag/Whirlpool again.

Bought the washer in February 2012 for $900 at a local appliance store, delivery included. Just yesterday (10/16/15) a 5 cent piece of grey plastic flew out of the lid lock mechanism. Thinking this $900 modern piece of machinery painstakingly designed by intelligent people with university degrees would certainly work if I just stuck the plastic part back in. I just popped it back in, the lid locked, and the machine spun away happily (only having to run a correct cycle for an unbalanced load twice! What joy!) Fast forward 40 minutes, I skip down the stairs to go retrieve my flannel sheets (because its October in Pennsylvania, its getting freezing cold at night) and pull up gently to open the lid. It doesnt budge. About 2 hours later, following a screaming match and some furious googling, it was determined we would need two people to pop the entire top off the machine to extract my sheets.So in order to use the washer to clean clothing now, weve been unplugging the machine. Removing the three screws on the control panel (aka brainbox), unplugging the black and white wire from the brain box, taking the control panel off and sitting it on the dryer, and using putty knives to push in the metal clips holding down the top of the machine down, and prying the entire top of the machine back on its hinge. Then I can get my clothes out. Then doing so in reverse (dont forget to add detergent before shutting the lid! It will lock and you will have to pop the entire top off again.) to use the washer. All because of a 5 cent piece of PLASTIC. What brainchild figured, Eh, we can just use plastic for this important piece that the washer wont run properly without. It doesnt matter!? Someone that wanted to make $300 a pop doing service calls thats who.I cant believe Maytag has gone so far down the tubes. In case anyone else ran into this problem and needs to fix it, write down the model number, serial number, and other crud listed under the lid. Then use them to wipe while youre in the bathroom. All you need is the company and part number on the lid lock mechanism. According to Maytags website my washer doesnt exist. And there was no way, no matter how creatively I googled, to find a part for it with the Maytag model number. So now I have to try to find this measly mechanism to replace and try to use this piece of crud for a few more months. I guess my Christmas present this year is buying a new washer. And you can BET it will not be a Maytag.And two more things: with no agitator, you can fit really big stuff, but you also get to hear your washing machine dancing on your basement floor with an uneven load. No matter how many times you try to re-position items, it runs a corrective cycle, refills with water, and spins everything into a ball AGAIN. Also, the miserable thing is starting to rust. Right on the sides and near the lid hinge, and all around the bleach receptacle. How cheap, a washer on which the paint rusts right off with chlorine bleach.I wish I still had my Grandpas old 1930s wringer Maytag. At least I knew that one would work without a cheap piece of plastic. And at this point I might prefer wringing my clothes to hearing my washer try to escape. In short: cheap parts, no replacements available through company for DIY repairmen, company designed to force customers to use their servicing for $300 a pop. 1/10 would NOT recommend Maytag.

Purchased Maytag 3000 series washer and dryer in June 2009. Like many other reviews, the washer is making a terrible loud noise during the spin cycle. I contacted Maytag customer service and was told wait time is 10 minutes and opted for the call back option. Received a call back from an agent located in Tennessee, United States and he checked for recalls or projects and found nothing. Offered a technician call in my area for $112.00 for 30 minutes to diagnose the problem. I told him that if he checked on the reviews, he will see many regarding this problem and a bearing issue at a cost of up to $700.00. The Maytag repairman is not only lonely but out of business and Whirlpool bought them out. I would never again purchase Maytag or Whirlpool products. We are seniors and do not abuse our appliances and why do they not last at least 15 years. Talk about disposal washer machines, who can afford to purchase them every few years. The washer sounds like a jet going through our house when it is in the spin cycle.

Have had this side by side for a long time and it is great. Have not had any problems with it. Also have had an Amana which we love as well. These are side by side and are frost free and never have to clean.

Purchased new stove from Home Depot. Was delivered damaged after I opened it. Called Maytag and they cannot get a service man there to look at it. They keep on telling me I have a 30 day unconditional warranty, yet they cannot live up to their words. Absolutely amazing. Bought the Maytag because of the 10 year warranty. Do not waste your time. Buy locally at an appliance store not big box stores. Do not buy Maytag either - service is just a bunch of well qualified talkers and key punchers. Very poor buying experience.

Our 3-year-old Maytag refrigerator, MFF2558VEAZ, is forming a sheet of ice on the bottom of the freezer. The ice partially melts for some reason, and then water leaks out at both bottom corners, usually once a day. Others have reported the same problem. Contact with a repair person is yet to be done. This must represent a factory defect.

I have had two Maytag washing machines in the past. Both lasted 20 years. Three years ago I purchased my first Maytag front loader washer and dryer. The washer is terrible. Although I clean it regularly plus spend money buying Affresh tablets and leave both the door and the soap dispenser open, the washer smells and builds up tons of mold. Cleaning out the heavy mold in the soap dispenser area is almost impossible. I spray bleach in there and then try to stick my arm into the back where most of the mold accumulates. Cant really get it all. Also, there is a problem with the softener dispenser. It gunks up and gets clogged. Had to keep pouring hot water and vinegar into it. Contacted customer service who was no help - they simply wrote to clean the machine. Huh? The dryer turns sheets into a tight roll with the inside not drying.

I bought this machine about a year ago. It does not wash your clothes good. Stains nor smell does not come out. It makes this god awful noise that can be heard throughout the house... It suppose to save on your water and electric bill but no savings for me considering I have to wash items 2 or 3 times... I hate this washer and I paid a lot of money for nothing coz that’s what it does - nothing!!!

Just so everyone knows, Maytag, Whirlpool, and Amana washers are all made by the same company and almost all of the internal parts are the same. The differences are mostly cosmetic, its just a way to sell more of the same thing to different classes of people. Just like Chrysler sells Chrysler, Plymouth and Dodge, they all had the same engines, transmissions and electrical systems, just different looks to appeal to different people. I found this out the hard way after purchasing an Amana front loader washer and dryer that broke down on me every other week for a year. I got tired of it and purchased the Maytag 2000 series. This set also breaks down on a regular basis! This is when I found out from the repair company that services these machines that all I did by getting rid of the Amana set and buying the Maytag set was buy a different looking set. Now I am really pissed. This company works for Whirlpool warranty servicing Whirlpool, Amana and Maytag as well as other major brands. All same machines inside the repair man said! Look into it, research it online and call whirlpool for yourselves as I did. You will find it to be true. So if you hate your Maytag, Whirlpool or Amana front loader washer or dryer, research and buy from a different company or you will buy the same old problems again and again.

I have a Maytag front load washer, and it has been flashing codes since day one, smells like mold, does not spin water out, and at first, all Maytag could say is, Im using too much soap, the wrong soap, loading too full, and I have it on a stand that is sold with the washer that they dont recommend, after I paid $300.00 for it. Now, it is flashing an E3 code, and will not finish a cycle at all. Maytag wants money to fix the problem that thousands of consumers have, after paying over $1,000 for the machine. I will never purchase another Maytag product, for as long as I live.

Called Maytag. Was part of 2005 recall with Neptune Maytag washer. We did not realize it and now Maytag will not do anything. Now having dryer issues with a cracked drum. Called and there was no resolution or attempt to resolve.

I wish I had seen these reviews before purchasing this machine. The plastic tub cracked and leaked all over laundry floor after only 30 loads. Part is unavailable. We will have to wait 3-6 weeks for a repair. Manufacturer will not agree to providing a new machine. Machine is only 3 months old.

I purchased a washer and dryer model MAH8700AWW. In 2005, I purchased the extended warranty. In 2009, I had to replace the main control board and motor on the dryer. Now, I find out that the washer has a warped drum which caught on the door boot and messed the shaft up. I didnt know that it has probably been that way since I purchased it because every time I washed clothed, I had to stay in with it because when it would go to spin, the washer would walk out into the middle of the room. I called about it and they told me to put rubber pieces to hold it still. Now it is going to cost $ 821.95 to fix. That is more than I paid for the washing machine and Maytag will not help to fix it. I would like someone to contact the company and find out why they dont stand behind their products anymore.

I have a bottom freezer Maytag refrigerator that is about 4 years old. It started leaking and continued to get worse fast... It appears that the gasket around the freezer drawer does not seal about half way up. It causes a sheet of ice inside the freezer, so I am not sure if it leaks due to the ice defrosting. The refrigerator doors do not seem as if they shut tight either. After reading many of these comments about Maytag refrigerators, I am not sure at this point if it might be better to buy a new one rather than fix this one??? I looked for a recall and do not see one. Clearly this is a defective appliance.

Washer would stop right after it started. I googled the problem and found out it was a bad lock. These Bravo XL units were purchased in 2015. Called an appliance repair and they charged me $250 to replace the lock (service call was $98.00 and labor was $90). The repairman left and I started the washer. There was a loud sound coming from it. I called the repairman back and he said it was the gear case and basket. He said the basket was covered under the warranty but the gear case wasnt. Would be about $750 to fix....no way was I paying the cost of a new washer to fix this less than 4 yr old one. I called Maytag. They couldnt help me. I should have purchased an extended warranty they said. The cost to purchase the extended warranty is now $394.00 per year....please do not purchase a Maytag/Whirlpool appliance unless you like buying extended warranties.

The Maytag Bravos XL washing machine has a difficult time getting clothes clean. The glass top allows a person to watch the clothing being washed. After one watches this for 5 minutes, it is quite clear that the clothes are not being washed properly. Clothes frequently end up dirty at the end of the wash cycles. I personally believe the design of the agitator is so poor that it is not capable of moving the clothing around to come clean. The tub is a large 4.5 cubic foot capacity, but because it uses so little water it simply doesnt function as advertised. Often there is residue on clothing, simple stains like dirt marks dont get removed. In addition to poor cleaning, the spin cycle is simply bizarre; clothes are twisted to the point that the wrinkles created during this cycle will not come out during the dryer phase of laundry work. I am completely unsatisfied with my purchase and regret not researching this more prior to purchase. I am baffled that this product could actually make it through quality control at Maytag. I have had one service call under warranty to fix the lid not locking. This repair was completed with satisfaction.

I sent an email to Maytag regarding my Maytag Bravos washer which I purchased two years ago at a cost of $1,100. I have started having problems with the machine last week. I kept getting the UL error code. I called a certified appliance person to come out to find out what was wrong. I do not believe any of the appliance people know what to do for these machines.First, I was told it was the control board that needed to be replaced, then I was told the motor had a crack in it and it needed to be replaced, and then the springs needed to be replaced. So they replaced the springs. This was a Tuesday afternoon. It worked fine until Wednesday of the next week and I started getting the F51 code. Just let me say if you cannot stand behind your parts on a $1,100 washer that is only two years old, then something is very wrong. I am in for $159 on repairs so far. Who knows what the cost will be to finally get the machine repaired.

Maytag Appliances - biggest rip off ever! Home Depot needs to stop carrying Maytag appliances. I purchased a Maytag washer Type 832-A, Model number MHWE200XW00, Serial number HL11990545 in May, 2011 from Home Depot. After just three years it flooded my laundry room. Home Depot couldnt help me, and Maytag Customer Service tried to really rip me off.I called Home Depot, asked why they continued to carry a product they knew had terrible complaints and all they could tell me was they are sorry I am unhappy with my washer, then gave me Maytags customer service number. I called Maytag - first the guy tried to sell me a $400 extended warranty package - total rip off. Maytag should be ashamed, then said he couldnt help because it was past the time period. There is no telling how many people they are ripping off with that little deal. Consumer Affairs should be all over this. So then he offered to get a Maytag repairman to come to my house, but couldnt tell me how much the diagnostic visit would cost or anything else. He was worthless.I hired a local repair person to come to my home, the part is $140, its the tub seal, weak and flimsy - has a giant hole. I only wash clothes and towels, nothing else. My local guy is cutting me a deal on the labor, still going to be $200. Maytag isnt what they used to be and I will never, ever purchase another product from them again, ever. And I would suggest you dont either. Maytag appliances only last a couple years at the most, and its customer service is horrid.

MF12665XEM7 Maytag Fridge water runs on the floor: After reading the review and watching the video to fix, I called Maytag. They refused to help. We bought our fridge at Nebraska Furniture Mart. We have spent a lot of money with them too. My husband called to see if they would split the cost of the service call. They refused. My floor is ruined from the water leakage onto it when we are not home. We try to catch the ice buildup and remove it before it is an issue. Why is there no class action suit? There is definitely a problem with this fridge and Im seeing it online everywhere I look.

I have had to put two 50 lbs sacks of feed on top of my Maytag Neptune Washer to keep it from walking in my washroom. Looks like I am not the only one with this problem.

Bought a Maytag Bravos x MVWX700XX1 about 2 years ago and now the agitator barely moves and makes a very loud grinding noise. Never had a major appliance wear out so fast..is a piece of junk. Will never buy another Maytag product ever again. Their old ads about the Maytag guy being bored because he never needed to fix anything should be considered false advertising.

On 12/09/12, I purchased a Maytag washer, model mvwc200xw, from our local Menards store. About 6 months ago, the washer started making a slight banging noise, and would occasionally move in the spin cycle. Now, when washing a small to medium size load, the banging noise is very loud and does a lot of moving. I found nothing in the troubleshooting guide to help me on this, so I looked on-line and found several websites discussing this same problem. They stated that the problem was a snubber assembly and the replacement part would cost $4.55. They also said the washer would have to be taken apart to change out this $4.55 part.I watched a you-tube video of someone changing this part and quickly came to the conclusion that I would need help in doing this. A comment was left in the video from a Maytag repairman saying that the person changing this part was not doing it in a safe manner. The repairman stated that changing it in the way this person described in the video was DANGEROUS! I wrote an email to Maytag customer service explaining the problem and asked if there was anything they could do to help me on this 1 1/2 year old washer. I received an immediate email stating they would get back to me in 3 days. Ten days later, I finally received a reply. I was told there was nothing they could or would do even though I was a valued customer and that they understand and appreciate my feelings of disappointment.I worked for a large department store from 1970 to 1990 and sold appliances, one of them being the Maytag brand. At that time, they were considered to be a top of the line brand. This was why I purchased Maytag appliances for over 40 years. I am surprised and saddened to see a lot of on-line complaints against Maytag appliances and also that this 1 1/2 year washer needs to be repaired so soon. Obviously, times have changed. I figured it would cost me at least $100.00 to have this washer repaired. Rather than do that, I am going to take this in need of repair to a scrape recycling center and then go out and buy a new washer, but it will not be Maytag! Maytag will never disappoint me again!

What happened to the days of buying a washer/dryer and having them for years! To spend a thousand on each and have holes in the bellow causing dirty water to Empty on your floor. Not once replaced, not twice, 5 times!!! Now Im looking to buy another. Old school for me...

I bought a Maytag washer and dryer, the Neptune series and thought I was getting a top of the line, but now the dryer has quit working and the repairman said it is not worth fixing and it is only about 5 years old. So that is what I am so angry about.

Neptune washer and dryer, an all around good buy. Low water use and large capacity for the pair. Bought the pair in May of 2001 and have only had one, very minor, service call. Buying online usually proves to be the easiest and cheapest way to go. Economical delivery costs. Noise and vibration and overall solid construction. Dancing washers can be a real cause for being a deal breaker. Auto shut off for balance is a must. Cleanliness of wash and wear caused by washing and drying. Large capacity and multiple cycle selections for both the washer and the dryer are necessary.

Im not sure that the guys who designed this unit ever actually tested it. During the wash cycle, if you have something like a fitted sheet it will actually stuff all of the surrounding wash items into the sheet until it forms one huge, round ball. Then it gets really interesting because the vicious spin cycle sends the machine marching around the laundry room and this happens even if the wash has not balled up. I now try to evenly distribute the wash within the tub prior to starting the wash cycle but it doesnt work. So now I grab a cup of coffee and newspaper and sit with my washer throughout the entire spin cycle to make sure that the hoses dont tear out of the wall.

Bought this (Maytag Washer MVWB955FC1) on 1/8/18, was delivered late in January as it was on back-order. On 4/30/18, during a cycle, the washer made a pop sound. There was glass everywhere. The glass had shattered and exploded onto the floor and washer. The glass is on the inside of the drum and all over the clothes. Contacted Maytag and they sent out a repairman the next day. Repair said there is a point of impact indicated I dropped something on it. NOTHING was dropped on it. There is a point of impact, from the inside. The glass is pushed up and out indicating pressure from INSIDE the washer.Repairman says its not covered under warranty and that I had to pay for his time as well. He also said there are no known issues with this lid and washer. The lid is out of stock and wont be available for a while. I called Maytag and they gave me the same response, never heard of this.. and lid is out of stock. I found SEVERAL reviews/complaints in which, for the exact same model, this has happened to other people. This glass lid is dangerous and poses a serious safety risk to households that contain it. If they replace the lid, there is no guarantee this will not happen again. A child could walk by the washer and at any moment the glass lid could explode, send tiny shards of glass everywhere. I want a refund for this dangerous washer.