I bought my Maytag Bravos washer and dryer set about 4 years ago when I moved into my home. The performance of the washer has always seemed mediocre. Despite using the correct HE products, clothes dont get as clean as with other washers I owned. Many times the washer becomes unbalanced, gets the UL code and I need to move my clothes around to get it running again. A few months ago, the washer started a new behavior: stopping during the initial fill cycle and displaying an F1 error. I soon figured out if I hit cancel and then start again several times, it would resume filling and proceed with the cycle. Over time, I had to repeat it more and more. I read about other complaints and suggestions on the internet and tried pulling the plug for a few minutes to reset the control panel as well as turning off the breaker to reset the machine.After troubleshooting the problem for 15 minutes or longer, the machine eventually runs. Then I can run subsequent loads with no problem. After a week or longer of doing no laundry, when I try to start the machine, I need to go through the entire process of canceling the wash load and terminating electric power to reset the machine. I have called Maytag/Whirlpool and got unsatisfactory answers. I only wash two to three loads of wash about every ten days and sometimes even less. The 800 number for Maytag was automated and would only schedule a repair without asking about the specific problem or being able to talk with a person. There was no way to cancel the service call scheduled and I had to call another 800 number to finally speak with a Whirlpool representative who tried to help me. She connected me with A&E Factory Service to cancel the service call.Both representatives stated that most likely the control board is the problem and the cost for diagnosis would be $130 plus the cost of parts, which could run from $200 to $400 since Im no longer under warranty. I canceled the service call as the cost of repair would be easily be almost half or more of the cost of purchasing a new (and different) machine. This is the electronics module, something that shouldnt be worn down or broken by use or even user error. This is an integral part of the machine and if it has a fault (which it clearly does), the manufacturer needs to stand behind it and help the consumer. The customer service manager even admitted that models with other model numbers had had similar problems and a free control board was sent to those customers. But my model was not in that range.”I had purchased a Maytag Bravos dryer at the same time as I purchased the washing machine and the dryer had a problem within a week of the warranty expiring. A service repair person came to my home to repair the dryer as it was barely a year old and I did not use it for several months that year (due to other reasons). From the volume of complaints Ive seen online, the Maytag Bravos washing machines should have been recalled and repaired or replaced free of charge.

In 2011, we purchased this Maytag Centennial MVWC200XW1 washer. It will not complete the cycle when it goes into rinse and spin, will not empty water and once the cycle starts, it sounds like someone is inside with a hammer banging on the basket. Clothes come out with a powder residue on them and several pieces have had holes. Called Maytag and was told there was no service available in our area. I will never purchase another Maytag product. Used by two adults a couple of times a week, this machine should be trashed. I have to hand-wring our laundry as we cannot afford to replace at this point. My last washer was a GE and I had it for over 20 years, we replaced it because we moved into a new home thinking Maytag was the best out there. I checked for a recall because there are so many complaints on other sites but found none. We purchased from Home Depot and of course, they are no help.

Just purchased a maytag dishwasher from home depot. I did the install myself. The dishwasher will not work at all the panel lights up, but no water goes into the washer. I now must wait two days for repair. After reading all the other reviews, I am thinking about returning it for another brand. And yes the water supply is on. I have hooked up several dishwashers. This is the first time a brand new one did not work right from the store.

Maytag Bravos XL - I have always loved Maytag and never had any problems. In Feb we did some major remodeling with new flooring in our laundry room. Decided to buy a brand new washer and dryer even though our 10-year old Maytag washer and dryer worked perfectly fine. After looking at Home Depot and Lowes we first settled for a Samsung W & D but before it was delivered we shopped some more. After doing some inquiring we decided that we wanted to stick to a long trusted W & D line so we chose this washing mashing and matching dryer. From day one I decided I did not care for it. I found if I put too many clothes in that they did not come out clean. Any dark pants would come out with what looked to be soap or softener stains and would have to rewash 1 or 2 times. Now I can only put in about 4 pairs of pants to wash. I have been cleaning it once a month as the manual says to do but yesterday I noticed a terrible odor coming for the washer. I could smell it out in the hall. I did the cleaning again but still smell it. Now after searching the internet I find a video that shows the problem is mold under the drum. No amount of Affresh or bleach is going to clean something UNDER the drum. It is not my job to have to take this apart every few months and clean out mold and moldy water. Sounds like this problem has been going on for a few years and this should have been fixed long before this. I wish I had my old faithful washer and dryer back. Maybe I should have stuck to the Samsung washer and dryer.

I purchased my home in 2008 at which time I bought all brand new Maytag appliances, well the above the stove microwave Ive had to replace the door handle because it broke off and the oven I can only use the very top or bottom to cook on and I cant move them, otherwise the racks will fall through. I have burned myself numerous times as I cant pull the racks in or out and I found that out cooking dinner and when I pulled it out the rack fell through and my dinner went crashing down and splashed everywhere. Due to this fact I hardly ever use it. I contacted Maytag with no help, told me to buy new racks and those did the same thing so it was a $100. It seems as though the liner cant handle the self clean heat and if you look at my oven, the left side is pushed in. If anyone gets help with this issue please let me know. My model number is MERH865RAS serial # 14348133LX. Oh and my refrigerator is a side by side and I have had to have it repaired twice because my food kept thawing out. That model number is MSD2651KES serial 60869476LV all of these are Maytag products and were purchased brand new from Home Depot.

This microwave doesnt rotate in use, it only goes back and forth...not as good! I believe the rotating type of microwaves heat your food more evenly, but it might just be a personal preference. I would NOT recommend this type of microwave.

Add me to the list of people who hate this washing machine. It does not use enough water to get clothes really clean, leaves spots, is hard on clothes and tears them up, and the spin cycle gets unbalanced too easily. It has taken me hours to wash one load with a blanket in it because of the spin problems. I have not been able to restart the spin cycle without starting the wash cycle from the beginning.

In order for the machine not to break you have to disassemble the drum agitator during normal use... Very poor design. Mine lasted just over two years. My initial cost was $570... Dont waste your money.

350.00 dollars for repair on a 3 1/2 year old washing machine. Machine wont finish spinning and lid lock keeps flashing on and off and sometimes stays off. Never finishes spinning. A lot of complaints on this! This should be recalled! Always was a Maytag customer but no more!

Purchased refrigerator model # MFT2976AEMOO September 2013. First repair was 1 month after purchase. From compressor to moisture build up inside fridge. 7 repairs in the first year. Customer service disgusting. They simply dont care, and do not back their products. Work time lost waiting at home for repairs. Service men come and always have to order parts, which means 2 service calls for each problem. Our service man broke one of the drawers when removing it to do a repair which meant another visit for that replacement part. Continued to have more problems when warranty was done. Just replaced my 3 year old fridge. Could not afford to keep it any longer. Have never been more disappointed with any appliance that I have bought. Will never buy MAYTAG again. Product is inferior.

Ten years ago I bought a very expensive set of Maytag Neptune Washer MAH5500BWW and dryer units with the single all-in-one pedestal. The washer starts sounding like a freight train during the fast spin dry cycle. A service tech came out, turned it on, listened, told me it is bad outer tub bearings going bad. And the price to fix is $846. Its essentially a throw-it-away deal. The tech says he has done hundreds of these and its a 3-hour major tear down, the bearings are press fitted and you essentially buy a new outer tub instead of replacing the bearings in the old one. Maytag went out of business and was bought by Whirlpool. What a piece of crap and to think how great Maytag once was. Now I have a dryer and a pedestal that probably wont fit any other washer brand.

I love the front loading machines. Fabrics dont get beat up like they do with a top loading machine with an agitator. My Maytag front loader doesnt have as many bells and whistles as others, but I love it nonetheless. Reliability was very important to me when I bought it, so I talked to a couple repair men to see if this was one they worked on a lot. When I found out they didnt, I bought it.

I purchased a Maytag dishwasher because they are supposed to be known to be a good brand. But my dishwasher is 3 years old and it started rusting around a steam vent on the outside of the door! This issue has been ongoing but as Ive been busy, I havent had the time to address the problem with Maytag since its out of warranty anyway. But I feel like this should not be a warranty issue to begin with, it should be a recall issue. I had a plumber look at this, and he said that it was caused because the vent was not properly sealed during manufacturing. Now it looks as though mold spores are growing inside the steam vent! Maytag will not stand behind their product, so why should I invest anymore money into it?! I would rather purchase another dishwasher (OTHER THAN THIS BRAND) than dump another penny into this garbage dishwasher!

This unit is only 4 months old. It freezes everything, vegetables, eggs, etc. It took more than 3 weeks for the technician to show up at my door!! Performed a service modification according to the manufacturer specs. This did not work!! Call again to have a it fix. He show up almost 2 weeks later. This time he replaced a part, worked fine for almost 2 weeks. Now I am having the same problem. I had it with this Maytag piece of junk!! I will never buy anything from Maytag again!! PLEASE DONT WASTE YOUR HARD EARNED MONEY... IN MAYTAG PRODUCTS!

We purchased our Maytag Refrigerator brand new, about 18 months ago. It always ran loud so the repairman came out during the 12 month warranty period. He told us to unplug and reset it, but that never did the trick. Eight months later, the fridge stopped cooling. We called our local repairman and he told us ($97 later) that the compressor was out. He said we should contact Maytag because the compressor should be under a 5-year warranty. Then the nightmare began. I spoke to four different reps with a total hold time of about 2 hours. Two of the reps put me on hold to get a supervisor and/or consult another rep and I was mysteriously cut off each time. One rep told me my compressor wasnt covered under warranty. The last rep I spoke to told me it was covered and he scheduled a Maytag repairman to come and replace the compressor. I was thrilled. The repairman came out and informed me that the compressor was indeed out and handed me a bill for $137. I asked why I was being billed and he said because that was the way that Maytag had ordered the service call. I told him that the Maytag rep had assured me that Maytag was covering the repair. He apologized and said that not only was I obliged to pay for the diagnosis (which I didnt need because I had already paid my local guy for the same information), but that it would cost $900 to replace the compressor. I was flabbergasted. I called Maytag and they denied all responsibility. They said that even though the rep had assured me of Maytags commitment to replace the compressor under the 5-year warranty, he had made a mistake and I wasnt actually covered. So I paid our local repairman to replace the compressor, because by that time, we had been living out of ice chests for 2 weeks. That was 3 weeks ago. Now the unit is freezing water on the bottom of the freezer and then leaking water on the floor. It is unconscionable that this company be allowed to defraud people to this extent. I will never buy a Maytag again and I would like to be informed of any class action suit. This company should be deeply, deeply ashamed of itself.

I bought a new Maytag dryer model # MEDC555DW2 18 months ago. Prior I had owned a Whirlpool for 22 years and the only expense on maintenance was that I replaced 3 belts. This new Maytag started making a terrible noise so I called the store where I bought and they sent out a tech. $76.77 they charged me to...remove a penny from where it got lodged in the edge of the drum somehow. Maytag refuses to do anything about it and I feel like Ive gotten the shaft because I bought an inferior product. In 22 years Id guess I dried on accident over 100 dollars in change since I have kids. Should have bought a Whirlpool again and so should you. Ill never buy another Maytag product. Ever.

I have had my Maytag Bravo for 5 years now. I originally paid 1800.00 for the set. And yes that is without the tax. Well I also got a warranty. Three years after I purchased my set my dryer stopped drying my clothes. I called the warranty company for a repair man and lo and behold my warranty is over. The repairman came and said that my lint was backed up. He stated that it was a good thing that I called when I did because they have been known to catch on fire. I asked him how is this possible? I check my lint screen and clean it after every load. He stated that the lint falls off the screen and just settles at the bottom of the dryer. And sometimes the dryer will get so hot that it will actually set the lint on fire. He fixed it but now it is back to doing the same thing two short years later. Im thinking that Maytag must know about this now and I am wondering why they havent did a recall on these before someone gets hurt or even worse by trying to do laundry.

I purchased this machine (MVWB765FW0) because I had a good experiences with Maytag in the past. There is a manufacture defect in this particular machine. If I were you, I would not buy it. I’ve lost two sets of bedsheets and my wife had a dress that she loved that got ripped up at the bottom between the agitator and the base of the machine. Maytag knows about the problem and does not have a solution.

We have had this washing machine almost 1 year and the small problems have grown enormous. In addition to the constant soap residue left on the dark clothes (my guess is its on the light clothes too, but you just cant see it) the washer goes out of balance frequently (they are replacing the suspension, after they said its all working great). The repair man said Im not loading the clothes properly, I need to roll each item of clothing into a ball and then place it in the washer. Are you kidding me, my new machine has special needs? And dont put in too large of loads. What!!! Its an XL capacity but I cant do an extra large load, because half the clothes wont get wet or clean. Maytag blew it big time with these models, I could talk about the dryer too. Maybe next time.

I purchased this set 7 years ago and the washer started stopping mid-cycle and the dryer sensor doesnt work. I called the Maytag service number and after several phone calls (they had my name spelled incorrectly and the wrong address), was able to schedule an authorized servicer. He said the motor and motor controller needed to be replaced and it would cost over $900. When I said I expected my $1,200 washer to last more than 7 years, the service person informed me that the machines were made by Samsung (not Maytag) and just carried the Maytag label. He said the Maytag Neptune washers and dryers were the reason Maytag went into bankruptcy and was bought out by Whirlpool. I am disappointed Whirlpool/Maytag does not stand behind this product and will not buy this brand again.

Maytag French Door Fridge Model MFT267AEW10 - Not even 1 month out of warranty and the water line solenoid is leaking. It seems the water line installed at the factory was pulled so tightly that it has caused the solenoid inlet to start leaking. We really researched this refrigerator and thought we were buying the best. Not so, Maytag wont warranty it. The last purchase of Maytag I will ever make. We should have bought the Samsung but we were trying to buy American. Wont make that mistake again. Not a smart investment. Refrigerators are supposed to last a good ten years. How sad.

The control panel of our Maytag dishwasher stopped working when it was approximately 14 months old. We repaired it ourselves by following a reset directions we found online (push rinse button 5 times and then the cancel button twice). Also we cut the power to reset. Im not sure which of those two tasks reset it, but it worked until last week - now 28 months old. We are not able to reset the panel using any information that we can find. In trying to find repair options, we discover that there are a lot of complaints about the Maytag dishwashers control panels not working within just a couple of years. In speaking with Maytag, they tell me theres a class action law suit for this problem - meaning they do realize there is an obvious problem with their control panels, but are not acknowledging they have any responsibility to repair it. The law suit only covers the cost of the part but not the labor. The labor can cost between $100 - at the lowest - and up. Our Maytag dishwasher model # is MDB8949SAM1. Also noteworthy, our Maytag clothes washer gave out at less than 5 years. Maytag is no longer the company we all thought they were. Additionally, their faulty machines are costing their customers a lot of extra money. Not exactly what I would call a company with good customer service or even any ethics. We will never buy Maytag again.

I bought the Maytag Bravos because I was told it was top of the line and expected that Maytags reputation for quality would provide me with many years of dependable service without problem. Boy, was I taken for a ride! Unless you have a lot of money to spend, DO NOT buy a Maytag Bravos washing machine. After only 3.5 years of normal use (3-4 standard loads per week) and doing everything as suggested by the owners manual, my machine has developed a bad drum bearing. The cost to repair this bearing is $400 for parts and $200 for labor. In other words, I am forced to buy a new machine after ONLY 3.5 years of use. When I called Maytag customer service department to question them about my problem, their response was there are no recalls on your machine, so we cannot do anything for you. When I further questioned them about the lack of quality/dependability my machine provided, they again said, Sorry, the machine is out of the warranty period. Thank you for buying Maytag. If you buy one of these washing machines, you better have the extra money to buy an extended warranty.

Maytags reputation for quality is gone. Our Neptune washer has had mold, door lock seized up and wouldnt open, and now our dryer drum is cracked. Exaggerating your products reliability is one thing - this borders on corporate fraud.

Purchased a stackable washer and dryer (Maytag) for our new condo in Feb 2015. After it was installed a few months later the problems began. The washer wasnt removing the water from the clothes. We contacted Maytag and they informed us that they subcontract out to a company called Appliance Service of Central Florida (727-462-0394). Contacted Appliance Service and set up a date to be serviced. Since then, we have had Appliance Service out to our place over 8 times. They found fault in our control panel, our door lock, replaced our motor and have replace several other parts. It has been over 4 months since they started repairs on our machine and have informed me that they have a right to try and fix the problem. I have no problem with this but when and how long do I have to put up with this? They dont seem to care that my wife and I havent had a working washer in over 4 months.The people doing the repairs stated that this machine should have been replaced because it had or has several problems with it and after replacing the motor, electric panel etc it still isnt working. When I contacted Maytag they stated that as long as Appliance Service is working on the problem, it out of their hands. Is there anything I can do besides contacting a lawyer and spending more money?

It just keeps going. Still looks great. We have had our Maytag Neptune analog dryer for over 20 years. It has dried a usual 3 loads a day, with very little maintenance. We have replaced the motor, blower, and support rollers, but these are parts that were just wear and tear items, after years of extraordinary use. It has outlasted 3 or 4 washing machines.

It was alright for a while. Then it started ripping up my clothes. The machine is not overloaded, enough water has been added but, when I take the clothes out they are torn. Not a good experience. I have seen several reviews on the Centennials, none of them good. What is the problem. I am hoping my experience gets resolved.

We purchased Maytag Dishwasher MDB5601AWW/46171101NP when we built our new home. In the last several months, water was leaking out onto the floor. We called Maytag and they told us there was a recall on the heater element and that they would send the part out. We made sure they knew the reason for our call--TO REPLACE THE GASKETS!. Maytag contacted a local authorized repair person. When they called to set up appointment, my husband reminded him about the gaskets. The guy showed up without gaskets, saying Maytag didnt put it on the order! We called Maytag to set up another service call. The guy showed up again today without the gaskets. We were told they had to be ordered and that he would have to come out again! Three service calls for one issue! Aside from this, the circuit board has never worked right. We push the correct buttons, but never know what kind of cycle we will get. We learned to live with it. Our bottom racks are melted as well as the sides of the dishwasher. Now that we know about the heater element being defective, this may be the cause of the bad gaskets and melted racks. It will cost almost $300 just to replace gaskets, and yes, we have to pay a service call for it when it could have been done in the first place. We called Maytag to complain and were told that replacing the gaskets always takes two service calls--one for diagnosis and the second to put in part. They said they dont take the customers word for it when we tell them whats wrong!

We bought the Maytag Aqualift cooktop about a year ago & are continuously dissatisfied with it, for several reasons: 1) the cooktop is a huge nuisance to cook on. The burners are either raging hot (causing boil-overs), or too cool to simmer. The boil-overs then require much cleaning with an expensive cleaning agent. 2) the oven, whether you use regular or convection, underheats - so you can’t tell how long the cooking or baking process will take, & you have to monitor the cooking process. 3) the so-called self-clean is a joke; the oven will not be clean unless you crawl inside & clean it manually. Overall, I’d prefer to toss this range in the trash. I’m a good cook, but I get angry every time I use this expensive, poorly- designed product.

I recently purchased a new Maytag Commercial top loading Bravos from Lowes. It looked like a sturdy model and has a 10-year parts warranty and to cover this washer even more... I purchased the additional warranty from the factory. The washer is delivered, set up... First batch of laundry the washer is making all kinds of noise, the clothes are wet..water didnt dissolve soap packet... Repairman comes out..washer out of balance, cold water not at full pressure... Computer failure noted. Now still making a lot of noise, my clothes are twisted and intertwined and still dirty. My dryer isnt even taking the wrinkles out and even after I iron on hi steam the clothes are still wrinkled beyond belief... Im so dissatisfied with the washer... I want to return it... I cant believe Maytag would manufacture a washer that is ruining my clothes...

Food stored next to the ice dispenser freezes. Freezer floor builds up with 1 1/2 to 2 of ice every couple of weeks, door wont close and water leaks on floor.

I have bought Maytag products for years. I have a white Maytag microwave that is about 3 years old. It was given to me at 1 yr. old by my sister-in-law when she decided to splurge and create her dream kitchen and went with stainless. The door handle broke in the first year. We glued it. It just recently completely fell off completely-snapping at both ends. I am calling Maytag and attempting to have it repaired. I am otherwise very pleased with this appliance. I have had other microwaves for many years without this happening. Im hoping they will agree to repair.

Maytag dishwasher mdbh979sam1 - Every single one of the Maytag/whirlpool dishwashers with soft pushbuttons and LEDs will fail--check it on YouTube. They have a very thin printed circuit strip from the door controller to the brains, and this rusts through in a few years. You must buy the whole controller for $150, you cant replace just the ribbon. And youll be doing this every few years. Maytag disavows this if you call them. The design runs the steam past this ribbon, so it corrodes really fast. Get a real pushbutton or a real dial knob model instead. With this model, the issue shows up when the LED pushbuttons stop responding or randomly light.

In April 2010, I replaced my washing machine (still functioning after 12 yrs) to upgrade to what I believed to be the top of the line Maytag Bravo 5.2 HE washing machine. Module # MVWB850WL0 type: 580-02. This machine of 3.5 yrs leaks underneath and after having the service tech come to look he advised me it will cost over $800 to fix (I paid over $900 for this unit). He says its the bearings and went on to ask me if Id been using the HE laundry soap (as if Im an idiot) and went on to ask whether Id been washing bedding. SERIOUSLY?!? !... After much research on this issue, I discover that there are similar complaints all over North America. Very disappointed and I want this lemon replaced by Maytag.

Maytag Dishwasher with model number MDB6701AWS and Serial Number 41687985NJ.It does not clean dishes like it should. We tried every possible way to set control settings, and still the dishes come out dirty and spotted. Also, it doesnt dry like it should. We had a Kitchenaid before we moved and it worked great.

Okay, on March 2009, we bought this brand new microwave due to our major remodeling. We didnt move into the unit until February 2010, so the microwave was in its box for 11 months. After we moved in our condo, my husband and I had to travel for work for almost a year so our brand new microwave is very slightly, gently and barely used. Well, for the past 2 months, it had been acting up. Sometimes it heats, sometime it doesnt. For a 2 year old microwave, which we paid over $400, I would assume that it would last. It no longer heats up, so I called Maytag customer service to hear her tell me its not covered under the warranty and would cost $269 for repairs and there was nothing she can do for me unless I pay for a technician to come and repair it! No way, I swear it probably got used 5-10 times a month to heat up coffee for about a year. I am sure there are some major quality issues on this model because when I googled Maytag microwave, all I see is the same magnetic problems. I spoke to a group of my lawyers friends. If youre interested in joining a class act law suit, please e-mail me. I hate that people are being taken advantage of by these terrible companies. I cant believe how low quality their customer service and products are. Believe it or not, my $30, old microwave lasted me 14 years throughout my college years until we decided to replace it with the modern stainless steel one. It got noisier in time but not broken and still heats up just fine. This $400+ one lasted me only for several uses. Shame on Maytag, when I have time, I will be sure to write a complaint to the consumer department as well. I will dedicate my life in spreading the word out about their low quality product. Don’t buy Maytag unless you only plan to use it for a year or 2.

Model MFT2776FE200 worst purchase of my life! We purchased the Maytag French Door Refrigerator last year. Within a few months, freezer failed and we had to have a retrofit done. Less than one year it has failed again. No refrig for over one month and still no parts. Hundreds of dollars of wasted food and I’m asked by Maytag Service if I have an extended Warranty. I didn’t realized that a new refrig needed to have an extended warranty. Will NEVER purchase another Maytag product again. We are devastated that spending 3k on a fridge means you might as well throw your money to the wind.

I have owned three different Maytag washer/dryer sets. The reason for so many? Selling the set with the house upon moving. I kept my last set which is Bravo. I love Maytag for their features, their dependability, their reputation. I have never had repairs on any of them. Totally awesome! My second set had a neat feature of a drying rack where you could place a sweater or shoes and no tumbling. Sorry I sold that set w/ the house. I am very pleased w/ my present set of Bravo. No agitator. A coworker also bought this set. Maytag is the best!

Front load washer is four years old. Approximately two years after owning the washing machine it started burning and ripping our clothes. Maytag sent someone out to repair at no cost. The problem stopped. However, approximately two years later it is happening all over again. Thus, there is either a deficiency in the Maytag product or the repair has failed. Maytag will only repair at our cost. True, the washer is four years old but the same problem keeps happening. Plus, that is not a long time in the life of a washing machine. The customer should not be held responsible for a recurring problem with their product. The front load washer and dryer were very expensive. We will NEVER buy Maytag and we will continue to share our disappointment to whoever will listen. It is shameful that Maytag says they stand by their product but when its put to the test Maytag completely fail. Double thumbs down for Maytag and customer service!!!

Maytag Dishwasher MDB7749SBW3 - Control panel problem just like everyone else describes. Bought in Nov 2014... how disappointing!! My husband is sure he can fix it if I buy the part. I went online to order the control panel, and of course because Im in Canada I cant ship the part directly from the website, I have to call the Canadian Sears Part Dept., its about $200! As I came across all these reviews I am even contemplating if I should waste our time and money trying to fix this thing... Maytag never again!!!

I have been using washing machines for 50 years. This is by far the worse piece of engineering I have ever used! On deep water wash, I would expect my clothes to be covered by water. I actually have to add by hand, four buckets of water and even then the clothes just float on top. The agitator NEVER pulls the clothes down to the bottom of the tub, they just move back and forth. The clothing that sits on top of the water, never gets totally submerged and is still on the top of the pile when the wash cycle is done. I will NEVER buy any MAYTAG product again. Lowes wont help me. I want to sell it, but in all good conscience, I cannot unload this on another person. I cant even feel good about donating it as it does not work...It is Junk!!!! Shame on Maytag for selling a scam. If there was any integrity in this company, someone would contact me and give me a better model.

My 2.5 year old hood range microwave stopped heating. I called repair guy, he charged $115.00 for barely a half hour and said he tightened a part and it should be fine OR the part would need to be replaced. Guess what!... That night microwave is still not heating anything. Dinos Appliance Repair is responsible to repair but Maytag doesnt stand behind its product. How do I get my money back when a repair doesnt repair anything? I wont buy Maytag again or GE.

I bought a Bravo washer 4 years ago from Home Depot. The spin cycle is stuck on high speed and sounds like a jet plane. Repair man came and said don’t bother to fix it because the bearing is gone. The machine cost close to $900. The repair man charged over $100. We are two retired senior citizens who dont do lots of laundry. I have read numerous complaints about the Bravo washer very similar to ours. Elder abuse should protect us from Maytag’s thievery and lack of help in repairs and replacement. A class action should be in place to address the Maytag Bravos manufacturing defects. There should be a recall and some type of reimbursement on this product . Please help us with this unjust situation.

We purchased a Maytag dishwasher & installed Aug 15 2012. After installation the control panel wasnt working & Lowes replaced the dishwasher with the same model. After the years warranty was up I started having trouble with the second dishwasher panel. I limped along with it for months until I could not get it to work at all. A repairman came and said that the touchpad & board was damaged. He said it wasnt hooked up properly. After an estimate of over three hundred dollars we decided to rid ourselves of it and purchased another, cheaper brand. Was out 79 dollars for the repair estimate & over 500.00 for the Maytag dishwasher. Plus a new one installed for 700.00. Had the use of this appliance less than two years.

The washing machine is rusting and Maytag refuses to take care of their inferior product and obvious inferior materials used, and also inferior workmanship.

Just so everyone knows, Maytag, Whirlpool, and Amana washers are all made by the same company and almost all of the internal parts are the same. The differences are mostly cosmetic, its just a way to sell more of the same thing to different classes of people. Just like Chrysler sells Chrysler, Plymouth and Dodge, they all had the same engines, transmissions and electrical systems, just different looks to appeal to different people. I found this out the hard way after purchasing an Amana front loader washer and dryer that broke down on me every other week for a year. I got tired of it and purchased the Maytag 2000 series. This set also breaks down on a regular basis! This is when I found out from the repair company that services these machines that all I did by getting rid of the Amana set and buying the Maytag set was buy a different looking set. Now I am really pissed. This company works for Whirlpool warranty servicing Whirlpool, Amana and Maytag as well as other major brands. All same machines inside the repair man said! Look into it, research it online and call whirlpool for yourselves as I did. You will find it to be true. So if you hate your Maytag, Whirlpool or Amana front loader washer or dryer, research and buy from a different company or you will buy the same old problems again and again.

The machine does not rinse soap off clothes even after using 2nd rinse cycle. You have to wash clothes again using no soap at all. Defective machine maytag does not help or Clare wanted to charge service fee for tech even though machine is under warranty. This washer should be recalled. Very bad product. Lots of complaints.

Fifteen months after purchase of the top load washer, we have had to call in repair. The lid lock and sensor have went out on the machine and the repair costs are equal to the purchase of the machine. Whether the consumer has an extended warranty or not, this is unreasonable. So hear this Maytag, the CONSUMERS will invest elsewhere when delivered cheap merchandise like this even if it is Made in the USA as you wish to tout in order to bait the consumer for their money instead of providing superior quality American products. This consumer is sending this machine out the door.

My Maytag Series 300 Dishwasher would not start. I read the reviews and took the door off (easy if you have the right tool), removed the control panel box (one screw), and cleaned the ribbon with electronic cleaner as per someones suggestion. It started right up. This is a bad design. Would I buy another Maytag? - No way! We will see how long this lasts. There is no seal on the door to keep out humidity. Do we really need a new control panel? When this is done...I am done with Maytag!

I purchased my Bravos washer and dryer in Sept. 2010. What a mistake! The dryer is okay but the washer is a nightmare! The repairman and I are on a first name basis. The last time he was here, he showed me how to recalibrate my washing machine. It stops working in the wash cycle, fills with water and then sits there. I have to manually drain it and start over. Then it gets confused and fills with water when it is supposed to be spinning and draining (consequently draining my well). I shouldnt have to recalibrate anything in life, much less, a brand new washing machine.

Our Maytag washer 4000 series was installed on September 2010. Within 12 months and 5 days, we are now waiting for our second spin bearing to be replaced. It is a repair that takes 2 guys and 2 hours, and they basically have to replace the guts of the machine. I can imagine this is, at minimum, a $500 repair. We didnt buy the extended warranty, but luckily, the appliance shop was able to talk Maytag into eating the cost since we were only 5 days out. With the purchase of our new house, we upgraded from our appliance allowance to this model. With everything going on with the new house and selling our old one, I didnt do my normal internet searches for customer reviews and that was a mistake!Maytag has since sent us a warranty extension offer for $350, covering 3 more years. I guess Ill be buying that. It sucks that you pay top dollar for a washer only to find out that you have to pay an extra 40% just to keep it running for 4 years. No more Maytags for me, ever. Note to Maytag, you sell junk and your business goes into the ground. You are selling junk! Stop trying to squeeze every penny out of design and build, or you wont have a job.

This is my THIRD dishwasher, and by far the best. The Bosch machine I had before that was a catastrophe: mediocre cleaning, intense filter cleaning required - at least every two days - and, with a pretended noise level of 47 dB, MUCH noisier than the 50 dB announced by Maytag. Somebody is laughing at someone! To sum up: the Maytag MDB4949SHZ cleans dishes incredibly well, is very silent and requires no filter cleaning.

Well, I thought I was buying quality products dishwasher and refrigerator and both are very disappointing. Of course the Maytag dishwasher (MBD7749AWB2) really upsets me since I just bought it in Aug of 2011. Now it will not finish a load of dishes and I did what the lady at Maytag told me. She said it was the control board. But it is not the control board. It is still working the same as it was. Now what should I do? When they said I had a 10year warranty I didnt think a known product like Maytag would let me down. MAYTAG, YOU SHOULD BE ASHAMED TO ADVERTISE YOUR PRODUCTS TO LASTS! THEY SUCK!

Bought a Maytag bottom door refrigerator/freezer about 3 years ago and within 6 months had the bottom drawer ice freeze issue that is so common all over the internet. Today is the THIRD ** time Ive had to take this piece of crap product apart and clear the ice. For all of you who have contacted Maytag in the past... Ill bet you got the same response I did when the fridge was new. They claim there are NO KNOWN ISSUES. They actually told me they had NO RECORD of previous complaints with this issue. MAYTAG SUCKS! I wouldnt take a free appliance from them. Worst customer service possible and they take no responsibility for their ** design and problems. There should be a class action suit for this issue. IF ANYONE IS EVEN CONSIDERING A MAYTAG APPLIANCE... Do yourself a favor and think twice.

The Maytag Bravo Washing Machine was sold as the top of the line. In reality it is very difficult to work with for three specific reasons. First, the spin speed is too high causing the clothes to be wound into tight balls causing pilling and the need to iron everything from t-shirts to workout pants. Second, the spin speed is so high that you can only put a few towels in the washer at a time or the machine goes off kilter several times a cycle. Finally, if you lower the spin speed the items take forever to dry. I used this for less than 30 days and tried to return it but Maytag would not take it back. The only cycle type I can use is the rapid wash unless I want to spend all day washing and drying one load. I hate this washer more than I can describe and will NEVER purchase another Maytag product. It absolutely ruins your clothes and Maytag takes no responsibility for making a very bad product.

This machine (Top-Loading High Efficiency MVWB755DWO) does not clean, it only leaves soap and moldy residue on clothes. The Whirlpool company refuses to assist even though it was delivered less than a year ago. So much for warranties! Wrinkles clothes, wrings incorrectly and does not give you freedom to manage independent of technological controls.

I purchased my first Maytag (Bravo Washer) appliance in 2013 and thought this washer would last me for a minimum of 10 years. It started making noises occasionally right away but I wasnt too concerned until it started sounding like someone was banging on it with a sledge hammer. I waited 8 days for a repairman who told me the bearings were going out and it would cost $400-500 to repair. This is the worst washing machine ever manufactured. My advice is to buy any other brand. Dont be fooled by the Maytag hype. Their quality is nonexistent. I am shopping for a new washer.

My new dishwasher had a defective board and worked erratically. Shortly after the warranty was up it stopped working completely. I contact both Maytag service and Home Depot on several occasions with no satisfaction. This a well known defect. Apparently the board replacement and service would cost in the range of $250-300. Too much for me as a senior on fixed income to justify. No dishwasher for almost a year. I then read an article indicating there was a class action settlement in California on the same make and model. I called Maytag again and after spending 2.5 hours on the phone I finally reach a person who sent out a service repair person. This person showed me a memo confirming the problem with the board. No recall but... if a customer is persistent they will give you the board. Finally new board installed at no charge.

My refrigerator was delivered on April 3, 2016. I began calling for service July 2 when the bottom freezer door started depositing ice chunks on my kitchen floor every time we opened it. An appointment for service was made for July 18, service never showed up. Another appointment for August 3 was made and again service never came. I called the 800 number on Aug 19 again arranged service for Aug 24 after hours so that we did not have to take anymore time off work. When repair finally looked at the fridge they said the door was not aligned and did not close so the frost builds up and breaks off onto the floor. This can be fixed with a new door that can take from 6 weeks to 8 months as they are not stocked and have to be made at a factory. The fridge constantly runs and is starting to leak water through to my kitchen floor and basement ceiling tiles.I called Maytag/Whirlpool on Aug 25 and the service agent told me the best they could do for me was extend my original warrant by 6 months while I wait for replacement part and they advised I purchase the extended warranty. The second agent named Gabby I spoke to advised me to call Home Depot where I purchased the fridge to see if they would do something for me. She would write down my concerns but had nothing more to say or do for me since the repair person deemed the unit repairable and a part has been ordered. I called Home Depot on Aug 25 and I spoke to Appliance Dept who told me the manager who could help me was off that day. He advised me to stick weather stripping around the door to seal the leaks. I said I was hesitant to do anything that may void a warranty and he agreed. He suggested I may get a loaner fridge but I have heard nothing yet. I want a replacement fridge.When you pay $2000 for a fridge it should be worry free for at least a year? I have been reading reviews and I am wondering why this is not a recalled appliance as this seems to be a very common problem. I am sad that Whirlpool is not standing behind this product. Home Depot has been in touch with me regarding this fridge issue and the lack of customer service provided by Maytag. They are replacing the fridge on Sept 9th 2016 and taking the old unit away. Home Depot has tried to get in touch with Maytag and they have not gotten a response at all about my faulty unit.The staff at Home Depot in Peterborough have been excellent to speak to and have apologized for the issues with getting service to my appliance. I am very grateful to them for their assistance and for following up with me in this matter. The downside is that I am getting another exact Maytag unit as a replacement so hopefully this does not start all over again. Home Depot has been a great retailer to deal with. I am very saddened to hear that even Home Depot cannot get responses from this manufacturer. I have also lodged a complaint with the Better Business Bureau.

I love it. It has a big tub. It has no agitator. It uses a lot less water. Many cycles.perfect machine. I would recommend this to everyone. Also top loading. Would never get another front loader. They arent worth it.

We bought our front load washer and dryer about 5 years ago and have had no problems with either. We also purchased a Maytag French door refrigerator 2 months ago to replace our Sears Elite brand when its compressor went out after 27 months (Ill never buy another Sears appliance).

I would say you have plenty of options when choosing a color for your dishwasher. You can choose black or stainless. Try one today you wont be disappointed. I load plenty of dishes into the space. It has extra pockets for little things and it has plenty of hooks and hangers to use for bigger cycles. Kenmore Dishwasher runs great. Very efficient and cleans the tough stains better than any dishwasher Ive ever used. I would recommend this to anyone looking to buy a dishwasher. Of all the dishwashers I researched at Lowes and Home Depot and Sears and Ace and other local stores, the Maytag was the lowest price with all the features I wanted.

Frigidaire makes a good fridge. It works good. It has an alarm when you leave as door open. Great appliance. If I could afford it Id get another one when this old model I have gives up on me.

Purchased this Whirlpool made Maytag Stainless Steel dishwasher Feb 2013. By Jan 2017 the washer was no longer operational. Due to poor factory design the touch pad wiring harness was crushed during the initial assembly. The harness is routed behind the touch pad/pull handle faceplate in the door. The factory design provided no clearance for the harness. Obviously after little use (opening and closing of the door) the pinched portion of the harness behind the pull handle becomes compromised causing the ELECTRICAL SHORT.I phoned Whirlpool the maker of the Maytag Stainless Steel Dishwasher for assistance, all they offered was a repair plan in excess of $300.00. I purchased this supposedly quality American Made Whirlpool product as well as a range, microwave, washer and dryer in the spirit of supporting US labor. Now Im stuck with a dishwasher that has an ELECTRICAL SHORT, possibly a FIRE HAZARD and Whirlpool trying to milk me for more money. Please think twice before purchasing anything from this Michigan based company.

I, too, am absolutely done with ANYthing Maytag. We purchased our Maytag microwave model MMV4205DS-1 in January of 2016. Within the first year we experienced occasional open/close door issues due to the faulty door latch switches. Now it happens virtually all of the time. The ten year warranty is a joke; it is just a come-on designed to deliver a false sense of security that Maytag will indeed stand behind their worthless products when in fact they wont. I am so disgusted with them.

I had my Maytag washer and dryer just barely over 30 days. My washer sounded awful and I had to get a new motor. Then my clothes would come out with dry spots. Not enough water. The computer was replaced and within a few months of purchase, all the major parts of my washer were replaced. I hate it! My clothes still come out with dry spots and it is loud. Worst major purchase I made. Dryer so far has been ok.

We have been married 50 yrs. We have never had a Maytag, we bought one 4 days ago, Dec.13, 2017. This is the worst wash machine (Maytag Bravos XL MCT) we have ever had, the clothes come out wet with white soap marks on the dark clothes. Lowes said we can exchange it for another washer, it will not be a Maytag.

We purchased a Maytag MVWX655DW1 Bravos MCT washer in 2017 and I recall a sloshing sound during agitation. Its a high efficiency model and was okay for several months, I think. It began to make something of a clunking sound during agitation that was similar to the deceleration sounds when the spin cycle completes. It seems that is an indication that something is wrong. Clothes arent clean after washing - another reason to suspect a problem. I observed the wash cycles and noticed that some items dont even get wet during the wash cycle. The clunking is probably an indication of the type of failure but I couldnt find anything other than someone else asking the same question when I did an internet search. Expected performance is shown in a company video with water sloshing during agitation. Thats the key take-away. My basket moves back and forth an inch or two during agitation and makes a clunking sound at each direction change. Water isnt sloshing through clothing and some of the garage rags that were once my clothes probably just needed a good washing. I suppose that even cleaning the washer isnt accomplishing much. The spin cycle is actually impressive. I load the washer evenly and find the completed loads with a towel or shirt evenly covering the clothes pulled to the basket below. Unfortunately, thats probably the only part of the process cleaning anything.The enclosure says its designed and assembled in U.S.A. and, unfortunately, speaks to our manufacturing ability. Some of the engineers Ive worked with over the years suggested areas to inspect. I was able to use my phone camera to look under the unit and noted that it is controlled by a main drive motor and a little synchronous motor with a linkage that Im guessing changes agitation direction. Both are made in China. Ive considered repairing it and just pulled the wash plate for inspection and found nothing beyond the difficulty of pulling the wash plate. Probably an issue with the drive assembly and a few hundred dollars in parts to fix. Ive also had input from someone about the cost of replacing the control board. I grew up with TV commercials of the Maytag repairman with nothing to repair in the world of reliable, American products. Its disappointing to find that is no longer the case. The low tech GE washers weve used all our lives were old and ugly when they left our house. Not defective, a few drops of oil below or worn finish but still working. It really is a disappointment to look at where we are today. It didnt have to collect samples on Mars or deliver orders in a self-driving vehicle. A reliable washer to clean dirty clothes is all we hoped for.

Consider all other manufacturers before purchasing a Maytag dishwasher. Our 3 year old model MDB8949SBB1 is junk. The control panel is a joke. Works when it wants to. Do not spend your hard earned money on Maytag.

Turned the oven on, and it failed to light. A little while later, it started leaking gas into the house. Im lucky the house didnt explode!

Worst brand ever. They both broke at the same time. Spend too much money. Never buying these brand again. Maytag sucks. Dont buy Maytag washers or dryers.

I have a Maytag Bravos washer that has gotten to where every time you try to run the final spin, you get an unbalanced load code and it shuts off - it does this even when you try running it empty. This washer is 3 years old, and has been doing this progressively worse for the last 4 months until now. We cannot even get it run the final spin cycle now.

I also am the unfortunate owner of a Maytag dishwasher Quiet Series 300. I bought it in April 2006. The control panel has been a problem since the first year of operation. Typically, one of the indicator lights would randomly go on and off during the machines off mode. At other times, the control panel would not operate. However, if I waited a few hours, it would dry out, enough and then would operate. Apparently, steam leaks into the control panel and causes it to be erratic. This has been a problem with this design for many years and the Maytag Corporation has not cared enough about its customers to correct the design flaw. I remember when the name Maytag indicated a top of the line product. Sadly, this is no longer the case. As a result, my loyalty to them has ceased.I probably will not buy another Maytag product again. Their standards have eroded.

I have Maytag Model MGT8885XS03 Gas Range. I bought it in 2014. The surface burner valves, which regulate the gas flow, are a bad design. One valve got stuck and needed replacement within warranty. Then another valve got stuck about a year ago and the third one got stuck about a month ago. I am going to replace these two valves now. My friend, who is helping me replace, has similar gas range. He also needs to replace a valve. His range is about a year old.

We purchased a Maytag Dishwasher Model #MDBTT60AWW3. Shortly after manufacturer warranty ran out, the control panel went out. Luckily we had purchased the extended warranty. The repair company came out and put a new control panel in it. Two months later, the control panel goes out again. The warranty firm sends out a different repair company. They replace the control panel again. This time it doesnt work. They replace some of the buttons as according to the repair person they arent registering the correct OHM reading. It works again. Yay!. A week later, its not working again. The repair company is coming back. This is really starting to get old. Between the multiple times it has broken down, waiting for the repair company to come out, diagnose the problem and order parts, we have been without a dishwasher for approx. 2 months the multiple times it has broken down. Im so fed up with this thing. I also will never ever buy another Maytag again. They need to have a major recall on these because of the terrible, terrible control panel. This isnt just me, its a lot of people.

I would highly recommend you do some research on the Maytag bravos XL machines and dryer.This thing is about as good as a piece of paperweight thrown in the fire for no good of nothing. Warranty ran out but it has a 10 year warranty so I don’t understand, bought one year ago been broke down three times in that time. Speed queen all the way.

I purchased a Maytag 4-door model, a little over three years ago. A little over a year ago, I noticed small puddles of water around the bottom of my refrigerator on the floor. I blamed the dog for having accidents and shrugged it off. Well, after months of putting up with this I came to the realization that it wasnt my dog, so I started looking for leaks on the seal, etc. Thats when I realized that the entire floor of the freezer was one solid block of ice! So, I looked online for people that might be having the same problem. Sure enough, there are A LOT of us!!! Now to add insult to injury, I have to have a MAYTAG certified repairman come and look at what needs to be done! He only charges $85.00 just to come to my house!!!! Thanks MAYTAG, I spend $2500.00 for a refrigerator thats obviously defective, and still have to pay more to have it repaired!!!

Low water level resulting in poor cleaning. Very poor design. Requires 2 rinses so the water savings of the wash cycle is a joke! Im very disappointed with the so-called Maytag quality. If doing very very small or handwash loads it work somewhat ok! Would never buy Maytag again!!

Have owned Maytags (washer and dryers) for 40 years. I bought a Bravos top load washer and matching dryer because we gave our old set to a daughter leaving for college. That was less than four years ago! We bought this because it conserved water and there would only be my husband and myself home. So laundry needs would be minimal. The washer quit draining and starting making a terrible noise several days ago. Immediately called repair service - I knew from the onset this was going to be a big problem because when I told them the model, they responded - uh oh! Two days later service man comes to assess repair and lifts machine up and tells me bad seal has leaked to gear box and ruined it. Soooo for a machine that is less than 4 years old, I will have to pay $280 for part, $79 for service call, $60 for labor and $35 to have them pick it up and redeliver (because the repair is too big to be made in my home). $454 for a machine that gets minimal use!!!! I can add another $100 plus and buy a brand new machine. Why should I have to??? In doing some research, I found out this is a common issue with this model and Maytag has paid for the repair of other washers because it is a common problem. Even the serviceman said that and recommended I get a hold of Maytag. Their response - sorry mam you dont gave an extended warranty. (NOW I HAVE A LEMON!) Guess my next step is to write a letter to Maytag Corporate Office. I will keep going up the ladder until they address this flawed machine problem! One thing is for certain - I will never ever buy another Maytag product of any kind or will I ever recommend it. They are just not reliable. Guess, nowadays they are considered throw away products - keep them a few years and throw them away because its not worth your money and effort to repair them :-(

My new Maytag washing machine does NOT CLEAN clothes or anything else. Waste of money. I have soft water, use bleach, hot water, Tide. I have even tried adding some baking soda. No use. I cannot wait until I can find a washing machine that works.

Machine is very loud. Clothes do not feel completely clean when wash cycle has finished. I have a sense that not all soap has been removed. Dark clothes have streaks of white residue. Must turn clothes inside out before washing. Very disappointed.

I love my dishwasher. The only hold back is similar to what I hear about all others and that is that it takes a long time. I love that is it quiet, has lots of room and is easy to use.

I bought my first centennial washer less than four years ago, warrantied that machine out. It was replaced by best buy because of the warranty that I purchased. We are a family of four, with that in mind the replacement machine was a model year newer and it last just over a year and quit. I bought the machine anticipating that it will last me the next 10 years. With two children at home now that is not working, all I have to do on replace a new machine. The repair shop has told me that they get more of the Maytag centennial machines and then any other washing machine is going to cost me more to repair it than to buy a new machine because I had faith in the Maytag products for many many years. This particular machines are extremely hard to diagnose as to what causes the problem or what the problem is and could take a long time to get it fixed as well as the expense of getting it fixed. I would not recommend another Maytag product nor will Maytag ever get any more money from us. This particular product has become a piece of junk that I cant even get rid of to recycling. Maytag has become a joke and this machine has become a 500 dollar hunk of junk in my opinion.

I have had my washer and dryer for 14 months and from day one, my washer eats holes in my clothes. It is always the bottom center front of my shirts. I complained about this and was told it was my clothes. They were either old, or the type of fabric, or too much bleach, etc. etc. Everything was wrong with myclothes except the washer. I purchased a new shirt and washed it without ever had worn it, and when I took it out of the washer, it has holes in the front. NOW YOU TELL ME that is the shirt and not the washer. I have used Maytag for the past 40 years and I never had any problems with the old Maytag washers. This new Bravos is a piece of junk and I am sorry I ever purchased it. I will never buy another Maytag product.

The stovetop is very hard to clean and gets stained easily. The heat works wonderfully and the burners are great sizes. The left side with the adjoining burners is great. The double oven is fantastic. Heats relatively fast. Another negative is the button controls. You have to push so hard for it to register. Its painful. Not the best way to do it. Just setting oven temperature is difficult. Wish that was different.

Maytag Bravo Washer - I recently purchase a fairly expensive washer built by Maytag. In my opinion it is the worst washing machine I have ever owned. Again in my opinion their advertising about being such a reliable company should be considered false advertising, and near criminal. If you had a lower rating I would use it. Absolutely you should never use the word Bravo in a description of this washer. I will never purchase a Maytag appliance again. Check the internet for reviews before you purchase. I had just came out of surgery and in a wheelchair and trying to move back home and didnt do my homework.

We owned the washer for 2 years and 2 days when we got a code F70. After searching online, I found hundreds, if not thousands, of reviews and self-help forums that show this product is in dire need of a recall. The problem I had is the motor control unit (MCU), which is a $225 to $275 part online. However, Maytag will only replace the board under extended warranty with a refurbished board that they say costs $330, whereas they say the new one is over $600. Why is it that Maytag charges double what everyone else charges? If so many people are having these problems, it is obviously a defect and should not be the consumer’s responsibility. It is obvious that this is too common of a problem.

The worst wash machine Ive ever used. It doesnt clean clothes well. It constantly had error codes. Im constantly having to unplug and reset the machine and 4 times out of five it will NOT restart. Not to mention it stinks worse than my sewer. I have to run the refresh cycle every four to eight loads. Ive owned this machine three years. And it has been three years too long. I will go back to a ringer washer or a wash board and have better results.

Like many I have never wasted my time writing a review, this time I have had it. Purchased all new appliances from Maytag, biggest mistake I have made in the last 10 years. Front loading washer is the main culprit. Doesnt clean clothes, have had to replace the rubber boot on the inside twice now, machine is only 3 years old. Maytag basically treats you like youre stupid, resend instructions like that will fix their broken P.O.S machine. I will never buy another Maytag and will be sure to let everyone know what a piece of garbage, from machine to company! Sad that the overall reviews on my machine are 1.3/5 stars on Maytags own website. Oddly, I cannot write any review on their site, Maytag must have realized what a POS theyve been selling and now block reviews. Im thinking that we should get enough owners together and file a class action lawsuit, maybe that would change their tune??? Never BUY MAYTAG, PLEASE keep in mind THEY are UNDER AN UMBRELLA with WHIRLPOOL and MANY OTHER MAJOR PLAYERS... Do not let them scam you the way they did me! If you work hard for your money spend it on a more reputable brand that will not try to stick it to you because they build junk!

Maytag MVW823OHC SLATE washing machine, $1050 plus warranty $169.95 on 05/27/21 not delivered until 06/25/21, error code on 09/19/21. It is 11/03/21, machine is not working and no part available. Sad.

I purchased a Maytag Bravos 500 Series HE washer. 3/2013. The machine sensor started giving problems less than 2 years after purchase. The sensor is not working. The wash lights stays on, and the clothes are not cleaned. I have to manually turn the dial to put in on the rinse cycle and then turn the dial to the spin cycle. Its a piece of junk. I called Maytag twice and the only thing the representatives on the phone say: I will send a certified technician to see whats the problem. Price: $129.00 service call and additional costs for labor, parts, etc. Maytag had a very good reputation for its products. Will never buy anything Maytag or any products that fall under that brand.

Maytag Top-loading washer MVWP475EWO - I just want to comment on how engineers have made our washing machines worse instead of better. I had to replace my Whirlpool Cabrio washing machine - and did try a new one of that brand, but had the dealer take it back. It had so little water when it ran and was a piece of junk. Anyway, replaced it with the Maytag and it too has the water saving feature (which I understand all of them do) but I have to put it on the bulky setting all the time to even get the water to at least cover the clothes. The clothes just barely, if at all, actually move! They sort of rotate a little at a very slow speed. Boy, maybe this was the time to try a front loader so the clothes at least moved a little in the machine! I am so disappointed in how all the machines are manufactured now. One dealer told me I would like the Speed Queen, but it would take five weeks to get one. Thought this Maytag might do the trick, but now Im stuck with it anyway. It does not spin the clothes out nearly so well as my old Cabrio did. The clothes are pretty wet! So, another fine engineering feature. I wish the engineers would be the ones that actually did some laundry so they would see how bad the machines are. My daughter has three young boys and theres no way this would clean the clothes for her. I told her she should be glad her machine is still working. The dealer was very nice about it when I returned the other one, but it seems all the machines arent really made to clean clothes anymore.

I bought a Maytag Dishwasher. The control panel has been replaced 7 times! About the protection plan that I renewed every year, the representative said that in order to replace a lemon, it had to break down 3 times in one protection plan year/12 months.

The whole Control Panel lights are turned off for several minutes. Then they return on. Frequency? Few times per day. Reason? We dont know. No water or ice are dispensed when this happens. No water pipe is kinked, water pressure is OK, no problem with cooling system and nothing happens with food inside refrigerator or freezer. There are no mention made in trouble-shooting section of customer manual. What should we do? In spite of this, we are satisfied with the product so far, after 3 years of use.

I purchased a new washer and dryer from Lowes a few months ago. I had my former washer and dryer for nearly 20 years and although the dryer started to have some issues, the washer worked wonderfully. To have a matching set, I decided to purchase both a new washer and dryer. I was told the Maytag Bravos XL model was the top of the line and could handle large loads. After just a few washes I realized this machine does not add enough water to get the top clothes wet and there is no agitator to pull the clothes into the water. I returned to Lowes and was told to use the deep water wash. I tried that and still had clothes coming out from the wash still dry and dirty. Unfortunately Lowes would not take the machines back and I was told to call Maytag. Maytag said there was nothing they could do except send out a technician for a service fee of $98 to help me determine if the machine is functioning correctly. I could not dislike a washer and dryer more! The dryer catches clothes on one of the screws inside and pulls fabric pieces out. This is in my opinion the worst washer dryer set I could imagine having. I will share my experience with as many people as I can to help others avoid making the costly mistake of purchasing a Maytag product. Maytag does not seem to care they have designed and sold a dysfunctional product!

We have a Maytag Gemini Double Oven Range Model MGR6775ADW. This is a gas range and it was purchased in 2006. This past Saturday afternoon after cleaning the dishes, the igniters on the range starting ticking on their own. I checked to make sure the knobs were not on and they werent. The ticking finally stopped after about 2 minutes. After the ticking stopped, we planned on going out for a walk. Fortunately we didnt. In about 10 minutes after the igniters quit ticking, the range burst into flames. Flames were in the top oven and shooting out the vent holes and the holes where the knobs are located. Coal black smoke was also pouring out of the vents. I quickly pulled the stove away from the wall to prevent the cabinets from starting on fire and I pulled the plug to shut off electricity from the stove. The flames subsided shortly after pulling the plug. The kitchen and house smelled of burning wire insulation and plastic. After doing some research on the internet, I found out that many other people have had the same problem. I reported this to Maytag Customer Service and they wanted to send a repair technician to fix it. I told them I didnt want it fixed but wanted it out of my house. I told them I didnt trust the range since some people reported they had it fixed and the fire occurred again. I wouldnt be able to sleep or go out anywhere knowing that the kitchen range could erupt into flames at any time. The factory authorized repair technician, from A&E, did come to inspect the damage and to report back to Maytag on his findings. He admitted that he wouldnt even trust the range in his house. After paying $1300 for this range and only getting 6 yrs. of use, I feel that we deserve some restitution from Maytag on this badly designed and dangerous piece of equipment they have been selling. Do not buy the Maytag Gemini range. This is a bad and dangerous product.

I have a Maytag Series 3000 washing machine which, as many knows, is the same as a Kenmore. I bought the set 23 months ago and since then, I have had nothing but trouble. In my first three months of ownership, I had my first error code of which I had to replace the hot/cold water valve. Fortunately, the unit was under warranty. Since then, I have had to replace the CCU and MCU twice. Now, the units MCU went out again! Whatever happened to the Maytag name? How can I get this permanently fixed or replaced? Is there a lemon law for appliances? Any assistance would be appreciated.

Purchased a new Maytag washer and dryer in November 2015 after having a old set not Maytag for 25 years with no repairs. WOW. Then the new washer went out in Feb. 2016, now the dryer in May 2016. Very unhappy. Is it because the machines are now made in Mexico? Cheap labor and cheap parts. ICK!!! Thank god for the extended warranty.

We purchased a home one year ago. It has all Maytag appliances that were anywhere from one year old to two years old. The Neptune LE washer is not working as of today. This washer is supposed to be the top of the line, and because it is almost three years old, it is no longer under warranty. This washer will fill with water but does not spin or rinse the clothes. We paid a lot for this home and were so happy to get appliances that were all practically new. Now, we refused to have a repairman come and charge us lots of money to fix a washer that should not be broken. I have had washers run for 15 years and that was when I was washing clothes for 6 people, including cloth diapers for triplets! I will not buy any Maytag appliances. I will be getting an Amana or a Sears brand. Please, no one go buy a Maytag appliance.

Buyer beware. This machine has received several complaints. Not long after purchase, the washer started to stop during the fill cycle and give an error code no. This is supposed to be sure to overloading the machine. The other reason they give is something stuck item the baskets. Again not the case. Supposedly it must be a motor issue. Maytag was my trusted band. Our last Maytag lasted us almost twenty five years.I was excited to get this machine but disappointed with the lack of clean clothes, error codes, and noisy operation. My first clue should have been the one year only warranty. Thats how much they believe in their products. Ill never trust Maytag again. So sad that whirlpool should sabotage the Maytag brand and turn an otherwise great washer manufacturer into a piece of junk manufacturer. Dont buy whirlpool either as thats how much they care for customers.