I have had and worked on many washing machines over the years. The worst design and complete failure of parts to easily align in Maytag front end washers is nothing short of staggering. Creating a tension wire to wrap a rubber seal that requires Hercules to install and easily tears the rubber is beyond ridiculous. Avoid front end Maytag washing machines like the plague since they may cause it given the mold and growth from excessive moisture when the seals tear.

I owned a Maytag Neptune washer and dryer for 13 years and never had a problem. The only one thing I would say about them is that since the washer had no agitator it would often tangle the clothes, but they were clean and not damaged so I was ok with that. We moved to another house in July 2016, and the moment we plugged in our dryer there was a spark and smoke under it. Our dryer was fried and it was because the previous owner put in the 220 outlet and wired it wrong. So our dryer was dead and cannot be fixed.Since the washer had the small problem with tangling clothes together, I convinced my husband to get a whole new set, not just a dryer. We went to Lowes and picked out a new Maytag Bravos XL, thinking that the brand was reliable and they were so big I didnt have to worry about doing bedding in it. Like ALL of the other reviews of this set, DO NOT BUY THEM! The washer does not use enough water to wet the entire load and you will be left with soap residue on your clothes and they will not smell fresh and clean at all. In fact, my son sometimes wets the bed or has dirty underwear and that is what my entire load of laundry will smell like when I wash them. Imagine taking a load of dressy work clothes out of your dryer and they smell like dirty underwear!I have tried other settings, different types of soap (liquid versus pod, etc) and doing smaller loads. None of this fixes the issue. It is obvious that Maytag and Lowes will do nothing about this issue, according to other reviewers, so Im not even going to bother to have them come out here to do a service call and charge me for it. So Im stuck with a $1,500 garbage laundry set! (Actually the dryer is fine, it just takes longer to dry than Im used to). Im all for a class action suit to get our money back and force them to stop producing such crappy products! Also, if you are considering this set, keep in mind that they have just over a 1-star average rating on this site, and that is because every reviewer is forced to add a rating of at least 1 star. If not, I think wed all pick the zero.

We got Maytag 2000 series front load washer just over a year ago. The bearings in the drum are already worn out. I will never buy a Maytag again.

We bought our washer/dryer from Home Depot and felt Maytag was a good bet. Guess again. Washer is running fine for now but after light use (about 3 loads per week) dryer failed. With no warning, I heard a loud pop about 3 min into a cycle and overheating. If I hadnt been home might have caught on fire. Good for us we live close to a coin laundry so in no rush to replace but can bet when I do it wont be Maytag and thats too bad. One of the few makers still building in the USA but thinking Samsung is looking good. This is the Maytag 2000 series btw.

I bought a Maytag washer (Centennial) because of its reputation. I didnt even realize this site was out here and would have made another selection had I known. I bought the washer on June 7th of 2011. On June 15, 2012, the washer just quit working. I called Maytag. They said since the warranty was over that I had to pay a technician to come out and it would cost $129. I was upset but I had to have a washer so I scheduled it. The tech came out and said the motherboard was bad. He said that this has been a common problem with this machine and that Maytag should actually recall the part. The replacement part was much better. He suggested I call and complain. The part was $180. He said that Maytag may reimburse me because it was so close to the warranty cut off. I called Maytag to explain the situation, and what do you think their response was? Since you already paid for it, there isnt anything we can do. Nice! What a joke. I will never buy another product from them and neither should anyone else.

Pretty much the same complaint as Ive read about the Maytag dishwasher control panel issue. I purchased ours in Nov. 2009, issues began in April 2011, and service call for $129 where the technician said it needs a replacement control panel. I spent another $130 for the part and warranty on this specific part. In December 2011, issues occurred again. I ordered a new control panel in January and was told 3-5 days, called after 10 days and was told it was on backorder and should be shipped sometime in March. Youd think the Maytag President would be embarrassed for producing a product like this that in my eyes has tarnished what was a reputable household brand. Not that it will do any good but I will mail a letter to the President. One positive, our kids are learning to wash dishes the way I did as a kid, by hand. I sure hope the new control panel we hope arrives in March fixes this problem for good.

I purchase the Maytag Bravos washer & dryer set 3 1/2 years ago brand new. I figured being a Maytag it would last for a long time but nope I was wrong??? I will never buy another Maytag product as long as I live and I will tell all my friends and family not to purchase a Maytag product also!

We purchased our Maytag dishwasher from Nebraska Furniture Mart in February 2013. The touch panel on our Maytag dishwasher quit working in December 2014, several lights would come on or flash or not work at all. The first repairman that we had come out took the panel apart, cleaned it up and put it back together ($100). It started working again but a few days later it started doing the same thing again. So I called the repairman back and he said the touch panel would need to be replaced. He called all over Omaha and no one had the part in stock. He called the Chicago Maytag warehouse and was told by them that they were out of them because there were so many defective dishwashers that they used them all. Now they are trying to find a new manufacturer to make them. It could be months before they get them in. So I contacted Maytag and of course they said that is not true and put me through to a parts company that they said has all the parts available. When I told that company that it was the touch panel, I was told by them that you only replace the touch panel for cosmetic reasons! So we got a second opinion from another Maytag repair company and he spent about 10 minutes looking at the dishwasher and said its a defective touch panel. He said he has replaced a lot of them in Maytag dishwashers. He recommended that I contact Maytag customer service and try to get them to pay for the part. I did call them and of course they refused because it is out of warranty. The supervisor even told me that they have not had any complaints about the touchpad malfunctioning! They do not stand behind their products anymore. I will never buy a Maytag or Whirlpool product ever again. I told them exactly how I felt and their only reply was Im sorry you feel that way. I am surprised they continue to stay in business. I dont understand how major stores can continue to sell their products when they are garbage. Based on the other reviews Ive read, Im not even sure we should fix this for $250.

Well Maytag, I have to say that I am very disappointed with your washer. When I put it on the bedding setting and try to wash a big load, it barely moves the load around. If you have a regular agitator to replace this useless one that is in this new washer I would like to have one. My laundry is barely getting washed and when you look inside the washer everything that is on the top stays on the top, not like the older washers where you could see that the laundry was getting sucked down with the proper agitator.

The design capacity of the dishwasher is not conducive to cleaning a full load. Within 3 months of purchase one of the interior baskets broke. I will never buy another Maytag product again. I was a fool in believing this was a top of the line dishwasher.

Maytag range model mer8875ws - Glass top broke on brand new oven over most used burner then glass spider lined out from there. Wife called Maytag and they told her that it broke from the impact of something dropping on it. I guess the man was psychic because he had no picture of SO CALLED IMPACT SITE. Now they wont replace or fix range, ** Maytag. Paid 699 for range they want to charge me 900 to fix. MMOOORROOONNSS! Like ** thats how big business treats everyone now. Thats how big business treats people these days.

I have a Maytag washing machine (MDBTT53AWW1). The total cost is $524 for machine plus installation. And the cost of yearly repair on this machine is $300.I purchased this machine a year and 10 months ago in January 2010. A few months ago, the control panel started to only light up partially but the washing machine continued to run. A few days ago, when i tried to turn on the machine, it would not work--the control panel was no longer lighting up. I called a repair man recommended by Lowes, and after explaining the problem over the phone, we scheduled a time for him to come (ten days later was his first available opening!).Ten days later with a broken washing machine and doing all the washing by hand, the repair man came late. When I made the appointment, I was told he would come anytime from 8 to 11 a.m., and of course, he did not show up until almost 1:00 pm. When he finally arrived, all he did was look at the model and determined instantly that the reason our control panel was no longer working was due to a faulty design. This dishwasher allows the steam to escape through a small vent placed to the left of the control panel. The steam inevitably causes a short circuit, meaning that this will be a reoccurring problem every year.He did not dismantle anything and was in my home for no more than 5 minutes. I was told the cost of a new control panel would be $141 plus his labor fee of $137. So all in all, if you purchase a Maytag appliance, the initial cost is irrelevant. If you purchase a Maytag appliance, you will spend almost $300 yearly to maintain it--basically the cost of a brand-new washing machine.Something needs to be done; this is unacceptable. The least Maytag could do is provide all of us, fools who believed in their product and thought that they were of quality, with a free10-year warranty for this faulty machine which is pre-determined to break down every year as a result of their poor design planning.Cost aside, what kind of world are we living in that major appliances are made to last just one year and then are to be thrown in the dump? There is no way I will pay $300 for the next ten years to maintain a product that is made to break. That is wasteful and disastrous for the environment. Shame on you, Maytag. You will be filling landfills around the country with your terrible products, and the world will be a worse place for it.

I purchased Maytag Washer and Dryer 3-4 years ago, upgraded to the premium washer and dryer, SS drums and have been dissatisfied from the start. The washer was extremely noisy; we were told this was normal. The dryer began making strange noises just outside the warranty period, and the belt and pulley had to be replaced. I was shocked at the cheapness of the pulley design, but the replacement part was of better quality. The washer began making a horrendous squeak shortly afterwards, again, outside the warranty period. The repairman said that they were all like that, Maytag used inferior transmissions and that it would be cheaper to replace the washer than repairing it. My mother had the same experience with a similar model. Needless to say, I will never purchase another Maytag product. FYI, there are only three people in our household, all adults, light duty use.

We purchased a washer and dryer two years ago. The washer got louder and louder until we realized something was wrong and we called to get it fixed. Luckily, that was within the time of the warranty. The noise, however, began getting louder and louder within a very short time. Maytag refused to fix it again. Now, the washer sounds like a jet engine and wont drain the water at all.

I depend on my front loading Maytag washer. It is very reliable, does a great job of cleaning even difficult items like comforters and pillows as well as items deeply soiled. I use the many features like water temp and level, fabric type, heavy or light load, etc. The only complaint I have is that the front cover of the detergent, fabric softener and bleach drawer came off and the exterior paint on top of appliance is rusting and peeling. A stronger substance for the surface where often detergent, fabric softener and other substances are often stored and they leak.

I bought this range Nov 2019, beautiful range that’s it. Stove top scratches very easily and hard to clean. Oven racks rust, got them replaced on the guaranty they still rust. Oven dirty never gets clean, If I could afford it I would on the curbside. I wouldn’t even give it away. 3 oven in 48 years of marriage, worst oven ever.... Sure would like a full refund, I mean 1500. What a ripoff.

I am extremely disappointed with Maytag and the representatives I spoke with this evening. One laughed after I told her I was 7 months pregnant and without a fridge for a week after owning it less than a year. I was repeatedly and curtly told, We dont cover that, when I asked only to replace the recent food I had purchased. After having to request a manager several times, I was put on the phone with Dana ID ** who said she would not be able to help with any food despite the delay of a week for repairs to our fridge. However, she could extend our warranty for 6 months.The only reason we were able to get someone out as early as we did was because we knew a licensed Maytag service repair company. Otherwise, we would still be waiting for someone to come out to tell us it would be another week before repairs. The originally assigned service repair company by Maytag did not return our call. There was no concern or empathy from the Maytag representatives that I was pregnant and could have eaten food that was not cooled to prevent bacteria growth that would harm me and my baby.Even their service repair technician recommended to contact them about the spoiled food since it was impossible for the repairs to be completed before the end of the week. We will never purchase Maytag again. The appliance failed with no warning in less than a year, and the representatives made no effort to resolve our issue of being without food for a week.

The control panel and the electronic control box had to be replaced after only two years of use. It cost almost as much as a new dishwasher (492 dollars). The model of the Maytag dishwasher is MDB77479SBM3. This dishwasher looks good from the outside and runs quite but the electronics are cheap and cant stand heat without melting. My wife and I are retired and only used this washer about twice per week. It looks good, cost 650 bucks and it is a pile of junk. No more Maytag in our house. We had this machine installed in July of 2014... It crapped out in July of 2016.

I purchased a Maytag Washer and Dryer about 3 years ago, they were under warranty for two years. Two years and 10 later the dryer breaks down, repair 310.00, two months later the washer breaks down again, 331.00, while I’m waiting for repair appointment the dryer breaks down, 130.00. Then I’m finally able to do laundry, turn on the washer for the first time since paying 331.00 and IT DOESNT WORK AGAIN, another SEVICE CALL!!! $$$ IM EXTREMELY DISAPPOINTED IN MAYTAG, ESPECIALLY AFTER VIEWING YOUR COMMERCIALS!!!

I had a tub failure on my washer Whirlpool Duet, which I bought brand new and it lasted 12 years with no problems. The dryer is still in use at my sons house. However, this failure lead me on a search for a set to replace the duet. I did some research and found the Maytag 6.2 Cu. Ft top loader and huge Dryer to match. The set was not cheap and it did have high marks for a great washer. So, I bought them both and had them delivered on 12/30/16. I have read all the owners manual and watched YouTube videos to see how to use this machine with all its pretty lights and sounds. I will concede that the machines look great, very impressive in my laundry room. I would bet it would even be a plus when I go to sell the house.THAT is all the nice stuff I can say. The machine does not clean clothes and I have done all the settings. I have changed laundry detergents, and even tried to add a little more water with a bucket at the start of the wash. (Saw that one on YouTube.) REALLY. That did not work, nor should I have to do that to get it to clean well. The answer seems to be, set the machine on FULL tub of water. So, I tried that for a couple of times and found that the clothes just float around and since they do not touch the Wear Plate they dont get clean. My wife (yes, I am a man that does most of the laundry) said she hates the washer and I was an idiot for buying this expensive piece of metal that does nothing but take up space and leaves spots on your clothes. Have you heard the term Happy Wife-Happy Life. Well not so much for me now.Spending money even $2,500.00 on a washer and dryer seems a little crazy. But I had the extra money and I have always wanted a MAYTAG. These guys know how to make a washer. Boy was I wrong, this machine must be an embarrassment to Maytag. I know I am really shocked that you would sell this machine as top of the line. I am not sure what Maytag will do, but I thought I would give you a chance to make this right. I have attached pictures of the machines installed and pictures of the model number plates. I have faith that Maytag will step up. My wife said this was a waste of time. The ball is in your court Maytag. (Come on Maytag let me win this one.) - Just a man and his dirty clothes.

I bought a Maytag Top Loader March 2021, this washer machine is the worst ever. It doesnt clean your clothes, & your clothes stink horribly. BBB and an Attorney needs to compensate for our all buyers.

I have had to replace the control panel on my Maytag Dishwasher 2 times in the last 4 years I have owned it. I diagnosed the problem using the serviceman repair manual which is located on the kick plate or lower plate for panel of your dishwasher. This is not one of the dishwashers that is listed on the recall list, but it is on the dishwashers list that Maytag suggested that you buy to replace your dishwasher that is on the recall list. Model number mdbh9898awb3.

Purchased French Door MF12269VM 22 inch from The Brick furniture April 1, 2012. Turned out to be a real April fools joke. Purchased extended warranty with TransGlobal for 5 years. First, fridge delivered after about a couple of weeks because it actually wasnt in stock. Naughty Brick lied about availability. Fridge arrives and after a service call from Maytag repair, they ascertain compressor doesnt work.Order fridge number 2. Two weeks later, get second fridge but lever for dispensing water is broken off. Order fridge number 3. Usual two-week wait and fridge finally arrives but the whole side panel is damaged. Send it back and order Fridge number 4. Service from Brick, Maytag and Whirlpool, terrible customer relations. Misrepresented delivery dates, supply issues, and operational damages.Fridge finally installed. Ice maker operates intermittently for the next year. Service techs from TransGlobal offer a variety of suggestions including changing filter, water pressure issues. Finally ice maker stops entirely in Summer of 2013. Is replaced after a month of waiting for parts of which the wrong part was sent. Ice maker continued to operate intermittently. Sometimes just a small of ice or no ice for a day. Finally in May after another service call, ice maker stopped working for about 4 days. Tech comes out and miraculously, it starts working again. A month later stops again and hasnt worked since.Contacted TransGlobal off shore call centre? And arranged to have an assessment to see if we needed a new fridge. Request declined and Maytag (Whirlpool) sent a tech out after another week. Service tech recommended new freezer. Waited a week for parts and arranged for Service tech to replace ice maker. Wrong ice maker part (for the second time) in less than a year.The latest trick from our possessed fridge is recent alarms from the temperature control. To say we are disappointed in this product, the retail experience, the quality of the manufacturing, the shipping procedures, the poor engineering and design, doesnt come close to describing the shoddiness surrounding this appliance and the service weve received.In conclusion, we are still awaiting an ice maker and are contemplating buying another fridge. What it is fair to say, we will never ever buy another appliance with their the Whirlpool or Maytag attached to it. Nor will we ever again buy anything from the Brick, or depend upon TransGlobal for repair services. Are there other Manufacturers and retailers out there who understand the meaning of service and quality. I certainly hope so. Otherwise Im going to invest in a good icebox.

Fridge Model MFF2258VEB6 - Our refrigerator is less that 2 years old and it wont make ice! The bottom of freezer is filled with water that froze. Everyday there is water on the floor. We asked at Home Depot where we purchased it and they said we need to change the filter. What filter? The owners manual is a joke. We cant figure out where the filter is located so it looks like we have to pay money to have someone come look at this. Hey, this is ridiculous. I thought Maytag had a good reputation and thats why we bought ALL Maytag appliances two years ago! Never again!

I bought Tapan gas stove last year, but all your ranges have a problem. Whenever we clean the range, it never goes straight stay up ,even when I bought from Lowes Store and I told them they said that defect from manufacturer. You have to correct your manufacturers defect, I want an answer as soon as possible. Thank you.

I purchased the top load Maytag Commercial Residential washer with an agitator last month. I wanted a basic washer with Hot/Warm/Cold settings, Delicate/Normal/Heavy Duty cycles, Small/Medium/Large loads. I paid over $800 for this washer and I cannot wash my whites or rags in hot water! The hot water setting dispenses hot water, then cold water, back and forth. The end result is cool water. Ive called Maytag, Ive been told that there is nothing that can be done about it, thats how theyre made to be considered HE. I asked them why they even put a hot or warm water setting on the washer.You have no control over the water level, all cycles except for normal run in a deep water setting (full drum of water), I dont know why delicates are in a deep water setting. I only wash a couple pieces of delicates together. I end up using a lot more water and detergent with this washer. I hope we dont have to conserve water in the next few years! So though this washer uses less hot water energy, it wastes a lot of water, my water bill goes up and my detergent is used up much quicker! I cannot add time to my wash cycle, (the actual washing/agitation cycle is very short - 10 minutes) it has to drain all of the water and re-start the cycle with more water! $800 is a lot of money for a washer that doesnt wash like my old cheap washer. The local store cant do anything about it and Maytag brushed me off.

I love this washer. You can fill all the way or energy setting but either way it does the job. I paid 1200 for a Whirlpool. it was broken within 6 moand couldnt get service repair. With the Maytag it was on sale for 550 cash. It stop spinning. I called for service. They were there in 2 days on time and 20 minutes it was working. It was a needle stopped it. Just reprogrammed and wa-lah!

Warranty dept. will not help you! I have been told by technicians sent to service my refrigerator after it spoiled food multiple times from not staying cold. The technician flat out told me that this refrigerator cannot be fixed but they are not allowed to say that it cannot be fixed. They will not return your calls and are just flat out rude. After asking to escalate a call, the rep said the manager will call me right back in a few minutes. Hours went by and I called again five minutes before they closed to speak to someone in management at that moment. This manager told me with no hesitation that they dont always believe what their technicians say because they send out techs that are good, okay, and not good. My first question is why is Maytag confident in the people they are sending to my house time and time again that stay for three hours?! She began to get rude and disrespectful and said, Well, if you had cancer, you wouldnt believe the first thing they say... I am in awe of these remarks. How do you compare a refrigerator to cancer?! I asked for a business address and stated that I would like the address to file with the Better Business Bureau and she told me that they have all the info I need. She refused to let me speak to anyone else. This situation is uncalled for when I have the technician telling me, This refrigerator is not repairable but they wont allow me to say that and Maytag will not make this an easy process for you. Unbelievable!

Almost one year to the date of purchase, my Maytag glass top range stopped working. The oven is still operational, but the range top does not work. The knobs turn and the surface lights go on but the elements no longer heat up. Trying to get a response from a real person at Maytag was impossible. I was put through a myriad of prompts that led me to scheduling a service appointment. I called AppliancesMart and got a wonderful sales person who said a service call would cost me 60 to 80 dollars and that he had not heard of repairs below $300 for this type of problem. Needless to say I am very angry and disappointed that I had not done more research before I purchased this item. If I can prevent one more person from making this same mistake, I will get some modicum of satisfaction out of this horrible experience.

I purchased a Maytag dishwasher at Home Depot in October 2009. Recently, it made noises for a few months of laboring, and finally would not start.Maytag said it’s out of warranty and wanted $125 just to diagnose. Took it to my shop for $60 to diagnose and they found a faulty control panel.

Last August I bought the Maytag Bravos XL. I have had 3 repairmen try to fix my problems with it and they cannot. The problem is, they cant fix an appliance that isnt designed correctly! Without water, one cannot wash. Dont be mislead that the huge area inside can be used for large objects like sheets and comforters. This machine is MUCH harder on my sheets and comforters than my old machine with a center agitator. I have shredded rugs, holes in sheets, black lines on clothes and a chlorine dispenser that puts spots on everything. The detergent dispenser hardware is rusted as well. Folks if this machine was an automobile, IT WOULD BE RECALLED!

I bought my Maytag Centennial washer & dryer about 2 yrs ago. It wasnt long after I bought the set, that the washer started having problems. I noticed the button to turn it on wouldnt go off. Then it was a pain in the ** to not be able to open the lid while the water was filling up. Something I havent noticed until today, its suppose to fill up to the amount of clothes that is in the washing machine. Well when I opened the lid there wasnt enough water in there to even cover all the clothes. Now I know why my clothes are not coming out clean!!! I am so frustrated with this machine and the company!!! DO NOT BUY THIS PRODUCT!!!!!

We bought this stove in 2014. One knob got stuck while my teenager was cooking food on the gas stove. He called me at work worried because he couldnt turn it off. My husband left work right away to go home. We thought it was just a bad plastic knob. Now a second knob is stuck in the on low position. There is a third knob that feels hard to turn. That will be 3 burners. This is ridiculous. Its a safety hazard. We consumers have to worry if the house will burn down, get CO2 in the air, and if our family and children are safe. We thought Maytag was a good appliance. I will not buy another Maytag. They should recall this stove top/oven. I have read so many of the same complaint on this website as well as online in general. I cant believe they continue to sell this with this much of a safety issue. Please take it off the market.

This machine doesnt wash your clothes. It leaves them dry & the agitator sucks too. I am so annoyed. I just bought them & had them delivered 7/27/15. It has only been a few days & NOT satisfied. Overpriced over $800 for it & its crap! Same with the Bravo dryer, it takes forever to dry. I wish I still had my old washer & dryer (had them for 7 years, NO problems). Very unsatisfied. DONT buy these, they are total CRAP!

We purchased a Maytag front load washing machine and dryer about 5 years ago. The front load washer is completely full of mold even though I have always followed the directions of wiping it out after each wash, leaving the door cracked, washing the machine with Affresh and even trying bleach and vinegar rinses. When I called customer service they refused to do anything about it. Then the dryer stopped working after 5 years and we had to get it serviced. Now, the door has completely come apart, as in every little piece has come off the handle and surrounding door frame. I have never seen anything like this on the oldest of machines and I have taken care of these appliances. I will never buy another Maytag...

Purchased this Maytag dishwasher from a local Home Depot in Feb. 2014, no problems until now in late July 2015 (about 18 months). The control panel is not responding. Start/Resume light is off, pressing it doesnt seem to do anything. Cancel light is off, pressing it does trigger the cancel drain process. Wash Cycle choices either dont respond, or for 2 of the choices engage an incorrect cycle. Option choices dont respond.Delay light comes on when an incorrect cycle choice displays but stays at 2 hours, can not be toggled off or to a different delay length. Holding Control Lock or Delay for 3 seconds doesnt seem to clear the circuit board logic. Problem began with the Cycle choice buttons defaulting to Rinse Only about three days ago. I assumed user error so let that cycle run, then was able to choose a different cycle (cant remember which one) which also completed. But since then the control panel behaves not at all or incorrectly as described above. Seems to be a common Maytag control board/panel problem, so will probably replace (with something other than Maytag) rather than repair.

I purchased the Maytag oven in January and have had the service technician out 5 times to try to repair the oven because it doesnt heat properly. Theyve told me that because I live in a condominium that it is normal for the oven to take an hour to preheat, then another hour for the second oven to preheat. When I am baking the oven does not hold the temperature and anything I bake takes much longer than it should. They refuse to get me a new oven.

Maytag is a reputable brand name for a washer & dryer. However, they have done very well in the oven/range industry as well! I own a oven/range for over 4 years now and it works great???! Food is cooked to perfection and cleaning???? And self-cleaning is a snap!

First the dishwasher - Control board no longer works. Seen many people with same problem. Dishwasher sitting there useless since cant afford to replace. Will cost as much as the purchase. Stove has defect between glass on oven door. Aqua clean feature is a farce and I feel vent at bottom of oven is asking for a disaster if any grease should spill in there. Maytag will not honor or admit any defects.

I loved my refrigerator because it was plenty of space, energy efficient and ran like a top even after 20 years when we sold the house. I look forward to buying another one when I buy my new home.

Purchased a Maytag front loader and matching dryer in Sears and have had nothing but problems with both since the beginning. Now that the warranty has run out we have even more problems and doing laundry has become stressful. Big lemons. Wish I had kept my Kenmore units. Now looking into reviews for other brands, may go back to the Kenmore brand too. NOTHING can be as bad as Maytag.

I bought the matching Bravos washer and dryer 4 years ago. I always bought Kenmore appliances but decided, based on the then reviews, that I would upgrade to Maytag. Biggest mistake I have made! I am a very tolerant person always looking for the best in anything. But I have to say, I hate both the washer and dryer. My clothes are faded, they shrink in the dryer even on delicate. I really cant say anything good about them. Today I washed 2 twin sheets, one king top sheet, and one very thin blanket. When I opened the washer, one twin sheet was on top and not even wet. So now I get to run another load and have to wait to remake my bed. When I have washed rugs on bulky, they are filled with soap when finished. Half the time, it doesnt spin out the water and I run a second and third spin cycle on a variety of items. I avoid doing laundry because it is so frustrating. I am retired so I cant afford to replace them. I just dont want anyone else to suffer the same frustrations!

Does not wash. Only very small loads get washed even though it claims to wash bedding. Some clothes NEVER get wet. Many times the clothes have to be rearranged and re-washed AND extra rinse. Cycles are over an hour each (then multiply x2!!). Maytag service has been called MULTIPLE times. They replaced the touch pad then the computer board. Both times saying the machine works “according to design/specs”. This is a Very poor design. Maytag should recall this inferior machine as it does not perform the job it is being sold for.

I purchased a Maytag dish washer (not even 2 years old yet). I bought it on 8/29/10 and I paid over $400.00 for it brand new. The model number is MDBH949AWW1 and the serial number is F03422327. I am only asking for the part (motherboard). I have lots of friends and associates at church, work and social that I have talked to about this Maytag. And I would like to give a good report about the company and what they make and that they stand behind their workmanship. I know for a fact that they have 22 motherboards on hand ready to go out and what I have read online is that many people are having the same problem. I need a motherboard. I believe this unit should easily last over 10 years, so I am not asking for much. I will have it installed myself. I just need the part. I trust that you are a reputable company that has been around for many years and Whirlpool has taken new ownership and they have been around for a long time, too! My own parents owned one for over 30 years. This is all that I would request. I’m thanking you in advance.

Wish I would have read the many, many, many reviews on the Maytag MDB8959SBS dishwasher before buying it. As noted by others, the touch control buttons stopped working 1 month after the 1 year warranty expired and Maytag wont do anything about it. BE WARY OF THE 10 YEAR WARRANTY CLAIM - IT DOESNT COVER THIS PROBLEM. Maytag should issue a recall on this product and do the right thing - take care of customers like they used to.

Maytag Bravo was making loud noise in the Spin cycle. Ordered new bearing, shaft and parts from Amazon. Also had to order the Bearing tool, cost more than the bearing parts. Total cost $145. Watch a youtube video on replacement, took about 3.5 hrs by myself. Biggest problem I had was lifting the washer up over the drain pan it is in. Washer is on the 2nd floor.

I give the Bravo T/L Washing machine and the Maytag company zero stars. I had to call for service 3 times within the last 22 months, twice for the electronic panel which needed to be changed, and the third time, it needing a new tub/drive shaft assembly at a cost of $405.27. I did receive a call from the Maytag customer service and all they would do is make a note of my complaint. I feel if you pay almost $1,000.00 for a machine it should work for more than 22 months. I believe Maytag manufactures an inferior product.Not only did it not last, my family and I found that the clothes didnt come out as clean as it should have, and sometimes, the towels would have a mildew smell to them after washing and drying. I assure you that I have read the enclosed instructions of how to use the machine, load the machine, and only used products designed for the machine

This Maytag (1979 model) is about as good as other dishwashers (I always rinse before placing in machine). It does have a lot more buttons that are not used than the last one I used (installed in the 1950s). Delayed start, choice of preheating water or not, choice of drying. Not big enough to do everything when have company and too big to use when no visitors present. When I am alone it takes 3 months to get enough to fill the machine and by that time they are getting moldy so most of the time I wash by hand. Black glass front with imposing row of controls across the top. I normally do not generate enough dirty dishes to warrant having a dishwasher. Since my wife died I have used the dishwasher two to three times a year.

I purchased the Maytag Bravos washer and dryer set one year ago, and have asked myself why ever since. The oversized laundry tub is what attracted me to the model, but it sure doesnt deliver for the money it cost. On normal settings, it doesnt use enough water for all the clothes to even get wet. After the load was complete, there were areas of my clothes bone dry, and obviously still dirty. I soon learned that the only way the washer uses enough water to get all the clothes wet and clean, was to set the machine on the bulky setting. This is the only setting I use now, but all of my clothes winds up twisted together, sometimes in one big ball. As for efficiency, that statement folks is a joke! Because I use the bulky setting, it uses much more water than a traditional washer ever did, and when the load is off balanced, it will go through another rinse cycle to try to even it out. This machine uses far more water and electricity than my old school set! I suppose if you dont get your clothes dirty, you may not need to use the bulky setting, but thats the only way I can wash my laundry with this machine. The old style set I had before this was Maytag also, and lasted about 20 years. I was more than happy to purchase Maytag again, but this set has been nothing but a disappointment. I dont plan to buy another energy efficient machine again, nor would I recommend this product to anyone!

We bought our Maytag dishwasher at Sears about 2 years ago. It has never cleaned very well, we have to rinse everything almost to the point of spotless before we load it. Its a water saver, which means it takes more than 4 hours to fully cycle. Just today, I went to turn it on and the start button does not work. I looked it up and found that this is a common problem with new Maytag washers. This is really irritating, considering we paid a lot more for the Maytag brand than we would have paid for something without the Maytag reputation. Live and learn, I guess; we certainly will not be buying another Maytag.

Maytag Bravo Washer and Dryer XL Series - This the worst washer and dryer I have ever owned by Maytag. I wish I could give them away. The washer does not clean my clothes and the dryer does not dry my clothes. They are absolutely terrible. Do not buy them, you will be sorry.

I purchased a Bravos washing machine 3 years, 9 months ago. It has stopped working, bad bearings. How can a major appliance fail after three years for bad bearings unless the bearing were bad to begin with??? The repair man knew by the sound the problem was bad bearings. The washing machine sounded the same as it always had, which means the bearing were bad from the start. My first washing machine, a Kenmore, lasted 21 years and a few months. How can you produce such a terrible product and expect I as a consumer would buy another Maytag product or recommend a Maytag product? Not to mention what will now enter a landfill someplace, terrible!

Eight years ago we bought all new top-of-the-line, stainless steel refrigerator, double oven range, dishwasher and microwave. All began malfunctioning within the first year: *The refrigerator began to make a loud rattle and the digital control pad needed to be replaced -twice within the first year. Within the next year the compressor had to be replace. *Dishwasher electronic control board was replaced twice, broke again and is still broken. *Microwave door handle broke off, and turntable motor broke.*Range burner ignition system only works on two burners and the shelf for the top oven does not fit -*Maytag refused to replace. Also, after using self-cleaning feature the lower oven still fills the room with smoke so it has been used very little. So, how much worse could it be? I had faith in Maytag-thats why we bought the brand.

All of my brand new white wash cloths have black stains on them. They look like mechanics use them to check the oil. And, my white denim capri pants have weird stains on them. This washing machine is a joke. It may be water efficient, but sacrifices cleanliness and stain removal. Maytag should recall this ** Queen.

On 7/8/11, the non-freezer part of the refrigerator failed to cool to needed temperature. This fridge is model MI TXEMMWWOO, with serial no EY4705715, purchased on 7/13/10 at Home Depot.We contacted Maytag and were told to wait until Monday. On Monday, we were told that a serviceman would be out on Thursday, the 14th. On Wednesday, the 13th, the serviceman called to inform us that he would come the next day and that he would have to collect for the call. Since the fridge was still under warranty, we demurred.We went to Home Depot for advice. They called Maytag, and after an hour of getting the runaround, we were told that the serviceman would come on the 19th and that the call would be covered by the warranty.On the 18th, the serviceman called with the same message as before: he would have to collect the charges for the service call. Another trip to Home Depot led to the advice to activate the extended warranty at this point.Under the extended warranty, the serviceman came on the 21st, had to order a new part, and finally installed the new part on the 29th, three weeks after the misery began, and after spoiled foods, many bags of ice, and great inconvenience.We have other Maytag appliances, but this purchase has been a cruel lesson in Maytags lack of product quality, deceptive warranty practice, and indifference to consumer satisfaction.

Bravos x - Ok so I was checking on my washing machine balance which is off. I came across the reviews and find how horrible the machine is! Grinding at last cycle, and not wringing out clothes on some loads. I thought grinding and wringing out was to be that way since it did it from day one. I thought I just needed to adjust clothes to wring out. Balance was taking out some clothes but it was put in properly. Boy was I wrong. Im so pissed after reading all your reviews. Im going to contact my daughters who works for attorneys about false advertisement and selling something they know is crap.

I bought a Maytag Bravos Quiet Series 300 washer just over two years ago from Home Depot. The control board and sensor went out last week. The service technician seemed rather surprised that a newer machine would have that kind of non-wear-and-tear problem and suggested that I contact Maytag/Whirlpool to see if they could help offset the parts costs, as the repair was going to cost over $600! The customer service agent I spoke with said that there was nothing they could do because the item did not have an extended warranty. I explained to her that we purchased this unit, even though it was out of our price range, because we were told that it would last a lifetime. I would have been happy if it would have just lasted 5 years! She was very detached and it was clear that Maytag/Whirlpool was not going to stand behind their product. I will now take the repair money and go buy a new washer. You can be sure that it absolutely will not have the Maytag/Whirlpool brand!

I have had two Maytag washing machines in the past. Both lasted 20 years. Three years ago I purchased my first Maytag front loader washer and dryer. The washer is terrible. Although I clean it regularly plus spend money buying Affresh tablets and leave both the door and the soap dispenser open, the washer smells and builds up tons of mold. Cleaning out the heavy mold in the soap dispenser area is almost impossible. I spray bleach in there and then try to stick my arm into the back where most of the mold accumulates. Cant really get it all. Also, there is a problem with the softener dispenser. It gunks up and gets clogged. Had to keep pouring hot water and vinegar into it. Contacted customer service who was no help - they simply wrote to clean the machine. Huh? The dryer turns sheets into a tight roll with the inside not drying.

Maytag MFD2561 - The metal piece between our French doors is also rusting. It is a design flaw. We also have a GE French door refrigerator and that piece on it is not metal!

Dishwasher MDB7749SBM - Have the same problem as everyone else, panel board (2nd one, 1st was under warranty). This panel W10475787 is 2 years old. Keeps lighting up doing what it wants to do. Dishwasher is 3 years old. Cant find out if there is a recall on this part (there should be).

My husband and I just purchased on 4/8/17 a BRAND NEW MAYTAG 4.3 CUBIC FEET CAPACITY FRONT LOADING WASHER WITH STEAM AFTER OUR PREVIOUS 15 year old washer that we both used just finally started having issues. So we decided to go new and with front loader with good brand. How sadly I was wrong! We brought our washer home, hooked it up and turned it on with 1/2 load of tiny laundry. It didnt even make it through one load! This POS started throwing error codes E1, E2, F8, F9, Suds and wouldnt drain any water. We reviewed the manual again, checked the filter hoses and detergent. All was fine but washer wouldnt work! I called Maytag 2 days later on Monday and after repairman came to look at it Thursday said it needs new drain pump and today now power wont turn on and nothing will work on front of machine, mind you this machine is brand new! I am so disgusted and angry that any company would sell this quality to anybody and at the prices they charge! NEVER AGAIN WILL I PURCHASE ANOTHER MAYTAG!

Maytag Washer Model#MVWC465HW2, just purchased it 1/30/2019, leaves white stains on dark colored clothes. I use liquid soap. I don’t use softener nor bleach. I use OxiClean on my whites and sheet softener in the dryer. Someone please out there help, I can’t return it, it’s past 30 days. I have extended warranty but they can’t help. It’s not broken. I hear a lot of bad reviews/complaints, but no answer if it’s been solved or how to solve it. Please someone help???

Love my washing machine. It is so big I need a step stool to reach down to the bottom. It cleans my wash well and I have dirty clothes. I hang my clothes on the line outdoors. My clothes have never looked and smell so good.

Model# MVWC200BW1 bought in 2015 tangles/stretches clothing. This machine is/has been a true disappointment. The agitator wings are not attached at bottom allowing clothing to get caught and as the agitator turns, so does the clothing causing stretching and severe tangling. Poor design compared to the agitator that would rise and fall - those got clothing clean and did not ruin them. I cannot trust this machine to moderately cost clothing for fear of their demise. The lock-down mode is not convenient for those last minute added items. Will not be buying Maytag/Whirlpool ever again when another machine is purchased. This is a piece of rubbish!

Maytag bravos xl - HORRIBLE at washing and cleaning the clothes. Broke a little after a year... Went to Maytag site, saw that they push 10 yr warranty. Transmission went out... but not covered?? Garbage.

I purchased a Maytag slide in range from Costco online in April 2020. Within three months a discolouration on the stainless top part of the range has happened. Costco has a ninety day period for repairs, or return on appliances. Pictures were provided to Costco at the request of Maytag. Upon review, Maytag’s response was, This is a cosmetic issue and nothing we will repair. I am an extremely disappointed consumer who will NEVER purchase a Maytag product again.

Our new Maytag Bravos XL machine quit just 43 days after being purchased. Purchased from Lowes, but since it was past 30 days since purchase date, Lowes could not do anything to help. Lowes directed us to an appliance repair service that they use. We had to wait another 3 days for repairman to come out to look at the machine... only to find out that a drain pump would need to be replaced, along w/ the diagnostics board since it was not working either. Parts would be ordered & were expected to arrive 3-4 days later. It has been a week later & the parts still have not been shipped out by Whirlpool. We are now on almost 2.5 weeks w/o a washing machine. I usually research & read customer reviews before making a major purchase. However, we had to quickly get another washing machine & dryer, so felt like Maytag was a SAFE choice since I had Maytag several years back. (That Maytag was your basic washing machine w/o the bells & whistles before machines had bells & whistles.) Will I purchase another Maytag again after this occurrence? Probably not. In fact, I am so aggravated & frustrated at this point, that I would love to just throw the machine out in the middle of the street!

I have owned a Maytag washer since 1989 (25 years) that has had absolutely NO PROBLEMS WHATSOEVER. It now has a slight leak, so I am considering replacing it. I contacted an appliance store and advised them of my problem. The salesman made a comment which indeed surprised me. He said that, although he would like to make a sale, I should do everything in my power to keep that old Maytag machine because they dont make them like that any more! From reading the reviews about the new Maytag now I understand why! I do not plan on buying another Maytag, which really saddens me, as they were once a high quality, dependable product.

Purchased new Maytag washing machine July 17, 2011. Have had several problems with it over the past three years. Most of the time it would not complete a load of laundry and would get stuck before the drain and spin cycle. Last week, the spin cycle became extremely loud. Had a repair person come out and was told the motor bearings were bad. Estimated repair cost $700. Purchased this unit new for $569.00. Called Maytag, was told that 10-year warranty on drive motor and wash basket did NOT include the bearings. Asked if they could help out with repair cost, was told no. Will never purchase another Maytag product again as they do not stand behind their products. Household has 4 people in it so use of this machine was light to medium.

I bought this washer almost 5 yrs ago and oil has been leaking from it. Called company who sent a tech to my home and declared it a total loss. All he did was tilt it for maybe 1 minute to determine this. I am out a washer. Nothing from this horrible company. They quit making the washer but cant even compensate the owner with anything to purchase a replacement. Will keep passing the word.

We purchased a Maytag dishwasher in January of 2011. Two years later the entire machine stopped working. We had purchased the extended warranty and the control board and panel were replaced. Now two years later it happens again. Maytag/Whirlpool is of no help nor do they care. DO NOT purchase their product!! Multiple complaints and issues with faulty control panels and the cost to replace one is the same as buying a new dishwasher so they cant lose. I will never again own a Maytag or Whirlpool product.

I purchased a Maytag commercial residential washer in late 2018, supposed to have a warranty for at least 5 years. We are in California and I was told that there was only one facility that could come two weeks later. I removed the front panel to have it ready for service tech, who on the first visit kept saying he did not know what the problem was, and left telling me he would order parts. After Christmas, I could not get in touch with service so again called Maytag. Service was supposed to come out on the 30th.After waiting almost 3 hours, he called to tell me he did not have the parts. Also, this repair tech treated me very bad since I removed the front panel which I thought I was being nice. He called me back on the 30th, said someone gave him a part, and came. All he did was remove control panel, lost the start button and told me it worked without checking it at all. He was rushing to another appointment so I tried to start it and it still had the original issue, which was slow agitator and a rubbing/grinding sound. Now, after he did something with control panel it had a clicking sound. I immediately called corporate and was told when he came back, which has now been over a month with no washer, that he would be with a senior technician.January 5th I waited all afternoon and he called and said he was not coming and that my whole washer would have to be rebuilt. He never replaced the parts on previous invoices I received, and I filed a complaint with the BBB. Now they are completely lying. Technician trying to say I had the control panel apart which is not true, and does not match up with the invoices I received. They are telling me my warranty is voided! Its been a month and a half. I was treated rudely from the beginning and now I am obviously being retaliated against. I have 3 kids, two with severe medical problems and have put so many hours into calling with all these issues.I had another service place come out and he removed the agitator and the transmission shaft/drive motor is rusted out, as well as the parts he said he replaced are worn and definitely not new. For this company to come back after all this time and say I did this, when I have the original invoice that clearly states otherwise is absolutely the worst service ever.I bought this machine thinking it would last, and now have to deal with all this. I have nerve damage and it is very difficult to take all the laundry for a family of 5 to do at laundromat. They refused to send someone else out, where they could easily have seen this repair tech never did what he said, and was unable to diagnose and fix the issue. Its appalling to me that this is how they treat customers. Laura ** at corporate is the one saying warranty is voided. The machine looks brand new as it has always been taken care of. They should be ashamed of themselves. Apparently, this is the standard a lot of times with people trying to get things serviced under a Manufacturer warranty!

I purchased a washer/dryer, Maytag from Home Depot Nashville. It was delivered and set up. 02/24/17 the date of purchase, delivered 03/07/17. I have tried in every way to get the washer to wash properly, but to no avail. The water level doesnt cover the clothes, it takes 10 to 15 minutes for the wash to begin its cycle. It doesnt spin the clothes dry enough to put into the dryer. The washer makes all kinds of sounds thats drives you nuts while setting up to not wash your clothes clean. I have contacted Maytag on several occasion about this problem, they sent out someone to service the washer. Now, why would a brand new washer need servicing. Somethings wrong. It isnt functioning up to standards and they should give me another washer.Now on 05/18/17 the washer was serviced, I have called them again to do something about this piece of **. I was told that the only thing they could do is come service it again. Why, must this brand new washer be serviced every week. It doesnt make sense... I dont want this machine, I want my money back so I can purchase a machine that will wash my clothes properly. I purchased a secondhand washer and dryer from a used appliance store, it lasted my family 10 complete year. The only reason I dont have it now is because I wanted to upgrade, since I have never had a brand new set. What a disappointment. Everything that looks good from Maytag isnt good. I dont understand why they wont stand behind their product.Somethings got to be done about this. Maytag will not take my money 1,200 and force me to keep this malfunctioning piece of nothing. Im going to Youtube this product so the consumer can see how this product doesnt work properly, therefore they wont waste their hard earned money. I will be contacting the BBB Nashville, and wherever I need to. I will let the consumer know the make and model of this product and where it was purchased from. Maytag I want every penny back. And, should hold you responsible for ever time I have had to go to the wash house because my brand new set wont work, and your company wants to service it every time I try to wash. I purchased this appliance on the strength of the well known name, that was the wrong thing to do.

I bought a new Maytag refrigerator on July 2, 2011. The ice continues to drop after removing your glass. Now you must pick the ice from the floor. Maytag said it has a 10 second delay and will continue to drop ice. Im tired of picking up ice and wiping water from the floor. Who wants a product that leaves a mess?

We purchased a complete, upper-end Maytag kitchen package from Lowes. So far, the MMV5208WS microwave has gone out 3 times; it was the magnetron all 3 times. The last time was a few weeks after the warranty ran out. After a lot of discussions with Lowes management, they then took it back and gave me choice of any brand. We picked a Samsung and have had no problems so far.As for the MDB8859AWS dishwasher, it was just stuck under the counter for the first 6 months of its life, because we were in the middle of a remodel and it wasnt plumbed in yet. Once we got it working, my wife loved it. Weve used it maybe 40-50 times since she was still hand-washing small sink-loads of dishes. A month or so out of warranty, it went out. There were no lights on the keypad and everything was dead. We thought it was the main control board, but it wasnt. Next, I tried the keypad, because Ive read many posts about these 2 things seeming to always go out on these models. I still have the fridge and stove, and hopefully they fare better than the microwave and dishwasher.What kills me is when I look at my old Maytag dishwasher and Samsung counter top microwave in the garage; both 15-20 years old and still worked just fine after getting replaced. It has never had a repair of any kind. I went out and spent $639.00 (it was on sale, the regular price was $799) on a ** dishwasher and it didnt even last a year. The microwave was close to $400, and it was on sale. I think my old Samsung microwave cost $79.99 when I bought it. You used to get what you paid for!

Dryer delivered nonfunctional. Tech showed up the following Tuesday. Diagnosis main board and one sensor dead. Tech returns following Thursday. Replacement board DOA. New dryer still nonfunctional. Awaiting new board with no functional $1100 dryer. This dryer replaced my three year old Maximus which was deemed too expensive to repair after three repairs. Please do not buy a Maytag/Whirlpool product.

OK, LAWYERS -- Where are you?!! You have a lot of very unhappy people who feel they have been justifiably TAKEN! Whirlpool needs to replace these refrigerators with another brand! We bought same bottom freezer Maytag refrigerator in 2010. Luckily, which we dont usually do, we purchased a five year warranty plan. Within six months we noticed the rubber seal on our refrigerator on the french door part was turning yellow and then getting darker. We feared something was burning the rubber. A Maytag repairman looked at it, called Whirlpool, told them that there werent enough parts to fix this refrigerator. Whirlpool asked him what they should do and he told him it should be taken out on the front lawn and burned (yeah for that repairman)!! Whirlpool agreed to replace the refrigerator with one, very similar but a new model #. Thank heavens, after our insistence, the warranty was extended to the new one. Now after about three years, we are having the same problems that all of you are having with the next one.. Our Home Owners insurance adjuster just gave us a settlement to have all the ceramic tiles removed, which are cracked in almost two dozen places, and whole floor replaced (minus our $1,000 deductible). The floor was put in new three years ago. The refrigerator repairman is next to come out. From what I have just read about all the complaints on this refrigerator, NOTHING is going to fix this problem short of replacing it at our expense. My advise to everyone --- FIGHT THIS. Write to Whirlpool (not Maytag -- Whirlpool owns it), and blast them over and over with letters and complaints and threats of lawsuits. Why should we be taken for that amount of money while Whirlpool does nothing but keep it. A class action suit is badly needed. Big corporations should not be able to take people over like this and get away with it. If it takes a lawyer willing to take on a class action suit, this is it! In the meantime, bombard Whirlpool with letters and dont stop! It takes persistence, but in the end -- most of the time, we will prevail. Big companies hope we will give up and go away. They count on it. Dont let them win!!! I have had a Maytag washer and dryer for twenty years with no problems. Problem is that Maytag doesnt exist anymore -- who is making this....?

We bought Maytag Dishwasher on October 9, 2019. Due to the installation difficulties we were not able to install and try it right away. Lowes warranty expired in 30 days, and the dishwasher is not cleaning the dishes. Even with the hand prewash of all of them-they come out dirty. I have to clean them after. The dishwasher is very weak. We contacted Maytag and were told that they can do nothing for us, only send technician (we have to pay $160 per visit). We can not return or replace it, the quality is very poor, so we will have just to buy a new dishwasher and lose 500$ for this product.

My Maytag refrigerator (bottom freezer) is about four years old now. Since the first year, it has been freezing up. The refrigerator gets warm and the freezer stays cold. Two repairmen have looked at it, replaced the electric panel and the thermostat - neither repair fixed the problem. If you completely defrost it, it will start working again. For about three years, it would work for a few months, but now it will only run for about two weeks before freezing up again. I called Maytag when this first started happening and again recently. They say they have never heard of anyone having this problem and they are sorry. The woman said she would put my complaint in my file. I certainly would recommend that people avoid Maytag refrigerators.

The oven range (model number mgr8772wb) will not heat to proper temperature. It runs 35 degrees cold even after the built-in adjustment of 30 degrees. the repairman said it was just a cold-natured oven and we had to get used to it. So if a recipe calls for 400 degrees, you must preheat to 430 degrees. As much as this thing cost, it should cook properly. I must rethink Maytags reputation. I thought they were the best. Wrong.

We bought our Maytag Bravo top loader on May 5, 2010. The machine was working fine. Then last week with no warning, the F51 error code popped up. We called Sears and they sent a repairman out. The result was the sensors work independently from each other (tested correct in the Ohms range). It made it through an entire diagnostic test, but will not complete a wash cycle. The repair guy concluded that the control board was bad. Estimated cost to fix was upwards of $400. I cannot afford to fix. Our issue with this product is that it is apparent, from reading all the forums, that this is a known issue. And we believe Maytag should be reimbursing consumers for this repair or they should recall the washer. Our washer is used on the weekends and it should have lasted us for minimally five years. All we wanted was to make it through one military overseas tour with it, not asking much. Instead, this machine lasted two years. Unacceptable.

My old washing machine was about 25 years old but still doing a fantastic job getting the laundry done. When the dryer died we decided to replace both machines so theyd match. I had been setting money aside for years in preparation for this purchase. Ive only had them for two weeks and I stay awake at night wondering what GENIUS decided you can get clothes cleaner in a tablespoon of water than you can in an adequate amount of water?! My old washer could wash a load of laundry in about 20 minutes. Again, what GENIUS decided taking over an hour to wash a load of laundry in a tablespoon of water was a better way?! What working woman would choose to double the time needed to do laundry and then not feel confident that the clothes are clean?!!! I am so mad and frustrated and disappointed and I dont know what to do. I wish I could yell at somebody!!!

I purchased a Maytag built-in microwave and oven combo in 2005 for my newly built home, but I did not move into the house until 2008. So the appliance has only been used for 3 years. The microwave stopped heating after only 3 years of use, which was for microwave popcorn mostly. I also purchased, at the same time, a Maytag cooktop. The knobs had to be replaced, a dishwasher, a rack and utensil holder had to be replaced and a washer dryer that doesnt work properly. I also purchased a side-by-side refrigerator which is okay so far. Im very disappointed in their appliances and they were expensive.

We bought a Maytag range Nov 2013. My daughter has maytag appliance and stand by maytag. We grew up with maytag. But those days are no longer. It is not about quality, it is about how many did we make, how many did we sell. I am very disappointed with my range. I tried several times to use my upper oven, in disbelief my lower oven was heating. This happened so much that I touch to make sure that the Correct oven is on. I also have problems with my knobs for my burners. I could not turn off burner after finished cooking. We had to unplug range and turn off gas, if we did not do that the burner would have remain burning. This very uncomfortable for us.I still believe in maytag. I am sure we have not talk to the right person. There is too much at stake for the company, too many complaints are bad for any business. I too am a victim, very disappointed, I wont give up. I have a warranty with home depot and they have been great. It is not their product but they sold it. I hope everyone with a lemon will get problems solved. We only want what we pay for, even manufacturer when they buy other products they want quality as well, we all do. Hoping everyone will be able to get justice. Thank you.

This is a top load washer, commercial series, high efficiency without any agitator. It doesnt use enough water to break down the soap, no matter what soap or amount is used. Clothes come out of the machine with soap patches. It is also virtually impossible to balance the load so when it spins, it bangs and thumps and walks across the room until it shuts itself down. Stirring and re-distributing the load, changing the size of the load, small or large (should you actually fill the tub to a full load per instructions) it simply doesnt distribute or balance itself at all. At the end of the day, clothes need more water for extra rinse and then doesnt seem to work with soap removal all of the time. You cant put a load in and walk away and do something else or it will bang around and turn off. A waste of money and time. Save yourself, buy something else.

I wish we would have never bought this brand and model. Within a month there was a loud banging and the serviceman came out and changed a valve out but it just got a little quieter but never went away. 2nd issue is cloths ball up when your doing bedding. Not sure if they are really clean or not. 3rd when we take the cloths out of the washer we are still seeing soap spots where they were not rinsed very well. We are using the right soap Gain but we cannot wash cloths in the bedding setting. We have to use the extra rinse setting to get all the soap out which defeats the whole savings issue of this machine. It says when you do your monthly machine cleaning it resets the water level but there never seems to be enough water in the tub. Also if your doing sheets in the washer and when the spin cycle starts you have to hold your breath to see if its going to get out of balance which it does 50% of the time so you stop and move things around. Also we cannot put a whole lot of cloths into this big drum because they dont wash correctly. Worst purchase we ever made. With all the negative reviews you would think that Maytag would come out with some fixes but I dont think they really care anymore.

Actually, I have had my Maytag washer and dryer for 20 years so they are not new but I am thankful for this set because of the workload it does for me. I sometimes wash heavy loads (blankets, bedspreads, small area rugs), and this pair performs superbly. My son wanted to buy me a new set for Christmas last year but I definitely said no. I truly am happy that I bought Maytag and I truly believe that the Maytag repairman is a bit lonely.

My Maytag refrigerator has driven us up the hill and back and has taken us several months in order for us to get the issue solved. This is quite an expensive fridge freezer and the after service has been diabolical to say the least. All their service calls in the UK were handled by a third party and it seems that there is some sort of change of ownership between Whirlpool and Hotpoint so after all the previous visits by different companies the problem of water leaking unto our floor is still going on and now all their call are being routed through a major insurance and a utility company who are more interested in trying to signing you up on one of their insurance policies than fixing it.To make matters worse the contractors they use are absolutely useless when it comes to fixing american style refrigerators. I was told I needed various parts which would have cost hundreds of pounds or that the appliance was uneconomical to repair. All of which was untrue. This I later found out when after emails after emails Whirlpool passed on the contact details of a service agent ags refrigeration who came out and found that there was a fault with the water in line connector at the bottom of the refrigerator which they replaced.

I bought a washer and dryer a few months ago from Home Depot Maytag. My clothes do not come out wrinkle-free. They are very wrinkled, to the point where I have to iron the perma press. The dryer I just got rid of was 30 years old, and always got the wrinkles out of the clothes. So I am very disappointed in the way yours works. I dont know what you can do, but this is not good. Thank you.

In October of 2012 we bought a Maytag Refrigerator Model MFF2258VEM. In the spring and summer of 2014, we noticed puddling on our kitchen floor. We thought it was our dishwasher or sink since the $1800+ fridge was new, but couldnt find the problem. We travel a lot and are gone for extended periods. When we returned in winter of 2014, we discovered that there was substantial puddling and found a sheet of ice in the bottom of the freezer compartment. We did research and found that this is a common problem with all the bottom-freezer Maytag models, which then leak. We discovered that the leak had seeped into our kitchen sub-floor and was destroying all of our kitchen floor tile, causing cracking and breaking, a renovation of just a few years previous that cost a lot of money. There was NO problem with the floor until we put in this Maytag refrigerator. The remedy for the leaking is constant maintenance and a lot of work, totally ridiculous for a product that costs so much. I want to sue Maytag for both replacement of the refrigerator and the cost of replacement of my tile floor. Can someone please advise? Thank you.

This Maytag is about 7 years old now, at least, and is still running strong. The one thing I do miss, though, is the lint collector basket that used to be on GE washers Ive had in the past. Kleenexes have a sneaky way to getting into the laundry and picking out the remnants is a royal pain! The lint basket on the GE would save me that task.

I purchased a Maytag Bravo XL from Lowes. Ive had nothing but trouble with it since day 1. I called Lowes and they said the hose that was placed on it was the wrong hose because I cannot use the the BULKY Cycle. Its easily to off balance and shakes the house. Im continuously having to restart it, it just stops and blinks without any codes showing, on all cycles. I paid $1,000.00 for this washer and will not purchase another Washer with sensors. The life span of the digital washers without agitators are maybe up to 3 years, if that. My last washer was a Whirlpool Cabrio Top Loader and it did the same thing. No More for this mom of three children, the older generation of Washers lasted TEN years or more!!!

I purchased a new Maytag fridge apx 8 months ago (model# MFF2258VEW6). It has french doors and a bottom freezer and from day 1 it has constantly leaked water all over my kitchen floor. I started putting towels in front of it after my first slip and fall. I had the water line checked for the ice maker and it was fine. It continued leaking day after day. Then I started getting a lot of ice build up all over the drawers and on my frozen food, which became freezer burned and I only had the temp at 2. They have a warranty on it, so called the company and they brought me a loaner fridge of the same kind.. OMG this fridge is doing the same exact thing, even worse. I am disabled and fell last night again and my leg and foot is so swollen.. I really hurt myself and Im not going to let this company get away with this!! I called the company and told them and they are checking into what they can do with the refrigerator. After reading all the about the Maytag bottom fridge leaks and other problems, I refuse to get the same one again. If they do not do something, I promise I will before I get hurt again!

This has the aqua cleaning technology, sounds real good. DOES NOT WORK! The cleaning is done by you as you nearly climb into the oven with a plastic scraper which they supply to scrape prior to the cleaning cycle. Then after you have used the distilled water in the bottom of the oven during the cleaning cycle (steam), you climb back in to wipe out the water and use something similar to a magic eraser to SCRUB the oven.Here is the real kicker....during the cleaning process, in between the glass (in the door) you develop water spots that cannot be cleaned unless you pay to have a service technician come out and tear it a part to clean it. According to Maytag THIS IS NORMAL and is proven (by their engineers without any documentation for the customers to be able to see) to be normal?? The consequence is a brand new stove will never be clean and it is the first thing you see when you come into my house. I AM EXTREMELY DISAPPOINTED!!!!

I have had a number of Maytag washing machines in my life and have never disliked a machine as much as the last one I purchased! The bleach dispenser is awful and any bleach that happens to land on the outer rim has ruined many clothes. I took them to my dealer to show him the ruined clothes and was told bleach does not evaporate do must be wiped off each time. With no soap dispenser I find I have to put the soap in first and keep trying to fill the machine some before I add the clothes. This takes forever but if dont do this my clothes are stained. I purchased this machine on April 11, 2017 and can not afford to go buy another washer at this time. The Dealer can not help me and when I called Maytag they were not interested! Buyer beware!

I purchased a Maytag made by Whirlpool in China about two years ago. The timer went out about nine months later. It went out again about 3 months after that and I paid to replace two sensors in addition. The washer still stops during a cycle at various times; it might be pausing or spinning or filling. When it finishes washing, sometimes it refills and leaves everything wet. I purchased from Deweys in San Clemente and they have tried to service but this is a real lemon. I will never buy anything again made by Whirlpool. I will research and find out what companies have been bought by them so as to avoid this. I note online that there are several hundred complaint problems about Whirlpool so they had to buy a company with a good reputation and ruin their product.

Purchased new washer mid-February from Maytag dealer. He said machine has few problems and it was a good machine. 3 and one half months later, the machine is dead. No lights on display but power at plug. Repairman comes at appointed time and says it needs a new circuit board. Within a week, the part arrives and an appointment is made to install the new board and still have the same problem. Have to order a new console panel. 3 and a half weeks later, the part comes in. I have a job which I used the money to buy this machine and now the service advisor wants me to take off work so they can try to fix this machine. He told me I cannot return the machine. Whirlpool Canada LP Customer Assistance said they could not do anything. When I asked to talk to her boss, she put me on hold. She came back and said they would give me 6 months extended factory warranty and she would email this which I have not received. Work schedules will dictate when the next appointment will be made.

My Maytag dishwasher model MDB7749SBM2 was two months out of one year warranty and the Whirlpool control panel went out. We replaced it for 80.00. 3 months later same issue. We had that replaced for free. 4 months later same issue. We had to fight but got that replaced for free. Now 2 months later same problem. It cleaned wonderful when it worked. I will never buy another Maytag or Whirlpool. I used to buy nothing but Maytag. We threw it out tonight. Tired of a dishwasher that is only part time.

I purchased a Maytag Centennial MVWC360AW washing machine on July 11, 2013 at The Home Depot. I assumed that I was getting a good product based on my Moms old Maytag washer. This machine is the farthest thing from quality that I have ever experienced. My Mom would roll over in her grave if she knew how CHEAP Whirlpool has built---what is supposed to be a---Maytag! The machine worked fairly well, at first. Even though I didnt like the low water arrangement. I like clothes to be fully immersed in water! That went on for 2 years and 5 months, until NOW the led light goes to Rinse, but it wont agitate. Then the led light goes toSpin, but it wont spin! I called a local appliance repairman and he told me that the control is bad. They cost about $250.00. Its not worth repairing!! So, Im stuck with this piece of junk! Shame on Maytag/Whirlpool for building a PIECE OF JUNK!

Our new refrigerator was pissing all over the kitchen floor. We had to disconnect the ice maker after an alleged repair part was supplied. (We had to pay a plumber to install it.) It didnt work, so we finally had to disconnect all the parts related to the ice maker. Here it is July, and ice cubes would really be appreciated right now. I get angry when I see all the Maytag commercials that pop up on the internet!