I am extremely unhappy. This is a terrible washer (Maytag washer MVWC565FW). I am so sorry I didnt buy a GE. Terrible loud noises, shakes and vibrates like a plane taking off. Funny smells as if something is burning. Repairman came 1 week after purchased and stated nothing was wrong. A huge waste of money, I HATE, HATE this horrible machine!!! Totally unsatisfied, I would never purchase anything with the Maytag name again!! Wish I could get my money back!

We purchased a Maytag Refrigerator-Freezer from Home Depot, in July, 2014. The first two months we had this appliance, it would not make ice (we purchased one that had an ice maker it the freezer!). After numerous calls to Home Depot and about 7 service visits, the service company gave up trying to get the ice maker to work, and instructed Home Depot to give us a replacement refrigerator. The new one came with an ice maker that works some better, but still very slow in making ice, and the new refrig makes a grinding noise every time we open the door. The Maytag Company, whose service people never have anything to do, say this is a cosmetic problem, and they refuse to fix it.Have been in consultation with Whirlpool Company (who bought out Maytag I assume), trying to get the appliance repaired... or at least put an end to the grinding noise. We paid a lot of money for this refrigerator freezer, and have had nothing but trouble and issues with it. If you are thinking about buying a Maytag refrigerator -- Dont!!

The brackets that make the door open and close are just screwed Into the plastic lining with no kind of anchors. If you use the freezer a lot the screws come loose. Can’t close the door. And then 300 dollars later a service call. All to replace a screw. That’s just fine but the hole is stripped because no one could install a 50 cent anchor on installation at the factory. No more Maytag for me.

This Maytag was installed in this house in the summer of 1984 and washed dishes for my in-laws for 26 years. We moved in as a family of four and this Maytag dishwasher is still washing the dishes clean. No rinsing, just make sure the food is gone. We replaced the belt about 6 years ago and I think my Mother-in-law replaced the door seal. It has a power saver button, 2 cycles, and the cups are on the bottom rack, plates and such on the top. I dont put plastic bowls on the bottom because it gets a bit too warm for them but all the bells and whistles still work. It is a fairly large model, WU301, with ample room for plates and platters. I dont wash pots because I dont like what the dishwasher soap does to the finish on them. Having the cups on the bottom is nice and the rack is very usable for other dishes as well. The cutlery rack is located on the top rack, removable and a decent size. Almond body, silver and dark brown accents, very 1984 but not a bad look. All of the buttons and knobs are easy to read and use. Maytag, 1984, model #WU301.

Although this refrigerator is 10 yrs old it really performs well. I like the ice maker as it hardly ever hangs up, the freezer works great and the refrigerator part is really super in the veg drawer and the meat and cheese drawer. All in all this was a great buy.

My wife and I bought a Maytag Bravos at the suggestion of a store employee at Lowes. Since we have owned it, I have seen the reviews and the washer has been a total let down. We have experienced all the same complaints. Loud noise, door lock not working, not enough water in the drum to wash clothes, and the bearings going out and it doesnt work. NEVER will we buy a MAYTAG again. To the scrap yard I go today. Thanks MAYTAG for wasting my money. Thanks LOWES for recommending this garbage.

I purchased a Maytag washer from Badcock. Within 7 months the control board went out. It was down for nearly 6 months. I had to use a laundromat until I finally rented one from another place. Now again months later the control board is out again (F2F3 Call Service). Due to long wait time luckily I have another warranty but am being told I have to wait 2 weeks before a tech can come look at my washer, and that they wont have a loaner or cant just get me a new washer being the problem is THE SAME! Spent hours on hold only to be told to wait AGAIN! I would NEVER recommend dealing with this company. They used to be top of the line, but clearly not anymore.

I have filed a class action lawsuit against Whirlpool for their faulty control panels in their Whirlpool and Maytag dishwashers. Please contact my attorney, Eppsteiner & Fiorica Attorneys, LLP, at 866-548-8857 and let them know if you own or owned a dishwasher with control panel failures.

We had a Maytag washer and dryer for over 32 years, the same washer and dryer. Finally our washer failed. We thought it would be a good idea to stick with Maytag. My husband purchased the Bravos XL Maytag washing machine. It is the worst washing machine ever and I regret the purchase. The washing machine doesnt clean clothes. If you use a powdered soap of any kind it leaves residue all over your clothes due to the fact it doesnt use enough water. It binds everything up. It becomes unbalanced with any larger load. Completely ties your sheets and your pants into knots. Yes literally I pull my clothes out and they are in a knot. The washer started to leak about two months ago after having it for a year-and-a-half. We couldnt locate the leak so we had to call a repairman and it cost us over $240 in parts and labor.

I have a bearing going out. The Bravo washer makes a terrible noise. Now, they tell me I need a new tub/bearing. This repair will cost me more than $250.00 plus service calls. This is the second repair that I have had on this machine. It is only 4 years old. I use it twice a week. I will not recommend Maytag to anyone and I will never buy another one. They should check the internet for complaints and realize that there is a problem.

The control panel died on this dishwasher (MDB7749) after only 2.5 years of light use. I was quoted about $250.00 plus labor to have the panel replaced. I will not fork over several hundred dollars for a defective panel, especially since many others have complained about repeated failures and known issues with the control panel. No more Maytag products for me. I plan to purchase a Bosch to replace it.

My oven looks like it has never been cleaned. The self clean Aqualift does not work to clean your oven. If I would have known that this feature did not work for self cleaning I would never have purchased this oven. My old cheaper oven at least came clean on the self clean cycle. Now it seems I am going to have to scrub my self cleaning oven. What a waste of money. Will never purchase another Maytag appliance.

The house I purchased came with a washing machine and when I used it the water didn’t pump out leaving me with a load of wet clothes. I went to our local hardware store the same day and purchased the only washing machine they had which was a Maytag high efficiency Top loading washer the same day September 30, 2020. Had the washer delivered and set up, and watched the washer work through the window in the top. The sensor on the machine only gave water up to the top of the clothes, not over them. When it went into the rinse cycle it gave the same amount of water. My clothes came out with soap suds on them and the clothes on top did not agitate down into the machine on the wash nor rinse cycle. Not once on the loads I washed in the two weeks I had the machine did my clothes come out clean and not twisted in a mess making it difficult to get them out of the machine. I used the expensive Tide HP pods and followed the referenced directions. In reading the other reviews on this same washer many of them had the exact same problems that I did. The warranty will not replace this brand new machine nor the hardware store so I am stuck with a washer that doesn’t work as it should and out of the money I paid for it.

I bought my Maytag Dishwasher (mdbh979aww3) about two years ago and just last week, the control buttons on the right stopped working. I see on this site that someone else had the same problem and explained that the wires got corroded, so now Im not sure I even want to replace the part when it only worked for 2 years. Now Im stuck buying a new dishwasher.

We bought a new top of the line Maytag MGD7000XW dryer about 2 years ago. It worked great for about 6 months, thing started acting funny. All of the front console lights stay on all of the time and it ONLY dries on high heat now. This all happened after the warranty period. So fine, I was going to buy a new complete front console (CONSOLE Part Number: W10388467 $300.) as the online repairman suggested. Guess what, Maytag no longer offers the part to fix my dryer. So now I have a 2 year old top of the line P.O.S. MAYTAG dryer that cant be fixed. I will never buy from this company again (Maytag).

My Maytag Neptune washer was purchased last October 2010. In the past few months, the washer has been making a loud noise when spinning/washing. I had a Maytag repairman look at the washer, and all the barring, etc. needed to be replaced, which would have a cost of over $450.00! I am very upset with this outcome and just looked into it and found that this washer had recalls that the consumers were not properly notified about. The lack of recall communication is inexcusable, especially since I even went as far as to buy a 3-year extended warranty and still was not notified.What really set this situation was that the repairman suggested to not buy a Maytag washer and he added that it would not be a problem since Maytag has been purchased by Whirlpool and that the Neptune washer played a part of the ending of Maytag! This whole situation has really put a bad taste for any Maytag product, and all of my major appliances are Maytag as well as the dryer I just purchased a week ago, before I knew about all of the disappointment of Maytag. I am sure the response I will be getting will be as good as the notification of the recall, which will be nothing. Thanks!

Very Poor Quality from Maytag Although (Dishwasher, model MDB8959AWS) - I knew Maytag always had a reputation of selling quality products I have never purchased a Maytag appliance because they usually cost more than other brands, so this is my 1st Maytag product. After ~25 months (after all warranties have expired), the unit stops working. The lights seem to have a mind of their own. I removed power from the unit for 1/2 hour attempting to re-boot the computer but the condition did not change. After researching the issue online, I found that Maytag has a two big problems: 1) Defective dishwashers, 2) Bad or no customer service.I am an engineer and this type of a problem (it happens from time to time) MUST be acknowledged and the customer made whole or the reputation of the company is destroyed and future sales will (and should) diminish to the point that the company may(?) go away for ever. I know products are not designed to last a lifetime like they were in the 60s & 70s but 3.3 years for a $650.00 appliance is way out of line. The dishwasher we replaced was ~18 years old, and we only replaced it because my wife wanted a more modern look.

We have had this washer for 1 year. I noticed right away my clothes would come out extremely wrinkled. Now not only are they wrinkled, they also smell musty. After researching I find others have the same issue, even finding a video of horrible mold under the drum. We called to have it serviced since we have a 5-year warranty. The service man recommended using Afresh. WELL, we do faithfully every month. He said they would not pay to have it cleaned, and even if he cleaned it, that the mold would come back. This to me is a major design flaw, one that could potentially make people sick. IF there is that much mold growing in the machine, with no way of cleaning it, and now the clothes are smelling, there is a HUGE issue!

Maytag 2000 front loading washer - This unit was purchased in Feb 2013 along with the matching dryer. From the onset it has presented with the problem of trapping small objects such as socks, underwear and other small loose objects in the rubber seal at the front of the door leaving them soaking wet and needed to be wrung out by hand. There is not any way to run a second spin only to wring out the clothes without doing an entire wash or rinse again rendering the efficiency void. I have been able to buy a mesh bag to put smaller items in for washing with the regular laundry load. However, this is not why I purchased the washer and I would strongly recommend to others not to buy this product. Very disappointed. I thought the Maytag brand was reliable. Never again will I buy any of their products.

Control Panel MDB8949SBB - I purchased my dishwasher in August of 2013. The control panel has stopped working and Maytag refuses to discuss the issue with us. Regardless of how many complaints they receive they are in denial about their product. They now offer a Repair +1 program which costs $260 for a repair and an additional 1 year warranty. If I do that I will get 1 year out of it before I run into the same problems. Any ideas?

We bought a Maytag dishwasher 4 years ago, we had to have it serviced a few months after purchase for the soap & rinse agent dispenser not working, then a few months after warranty was up the buttons on machine wouldnt work, the control panel failed so we had to pay for a new one and install it... Well last night exactly one year from the install of the new control panel I walked into my kitchen to find it full of smoke and the dishwasher pour out smoke, when my husband came home he took the door off and sure enough the control panel was burnt and melted! Very scary. It is a very good thing I was home and this is why I never leave appliances running if I am not home.

I purchased a Maytag self-cleaning stove in early 2009. Right away, the oven floor finish started to bubble up. I called Maytag service and was told the part wasnt covered. I let it go since it wasnt interfering with the function of the oven. However, in Feb 2012, the oven started turning off in temps above 350. I called Maytag service again and was told that since I didnt purchase an extended warranty, I would have to pay for the service call, parts and labor. I complained that I never expected their product to break down in less than three years.I had a private oven service look at it and was told the computer part was the problem and would cost almost $300 to replace; or I could just live with an oven that didnt go above 350 and buy a new one when it broke completely. You can be sure I will never, never purchase another Maytag product or any other product they involved with like Whirlpool. I am done with them and their inferior workmanship.

I called Sears to have a simple repair done to my Neptune washer and received a quote for $800.00++. They gave us a coupon to get a new washer at Sears and we did. Last week my dryer broke and I looked the repair up on Youtube. It looked real simple. A quote for $270 was given to us. Again a coupon if we wanted to buy new. It seems to me Sears jacks the price up on its parts and labor in order to push the customer to buy new. So far its worked for them and Im sure everyone else as well. Its not going to work out for Sears this time. Im no longer doing business with them and I will do the repair myself. I still got stuck with the service call but that will end as well going forward because I know now what the game is. Shame on you Sears. Double thumbs down for my Maytag Neptune washer and dryers.

I just had an astonishing phone call with Maytag customer service (1-800-344-1274). My mind is boggled; my tongue is tied. Only Consumeraffairs.com can offer relief from the bleak, solitary misery engendered by this disorienting encounter. I called Maytag to seek information regarding the number of gallons used by any of the wash cycles of the Maytag BRAVOS series 300 (Model: MVWB450WQ2). I live in California, and like millions of others, Im curious as to what the maximum amount of water used per wash might be. I told the customer service agent that Id be happy with an estimate of any parameter: the maximum water demand for any cycle, the minimum, the average any ballpark estimate would be great! My goal is to change in a meaningful way our weekly water use. How much does it matter if I do my familys laundry once vs. twice per week? Is it any more water-efficient to run one large load vs. two small ones? The Customer Service agents would offer only a scripted response to my query. Could they tell me the minimum or maximum amount of water used (on average) by any of the cycles? Any cycle any condition, just an estimate, please. A universal it depends was all I could extract.The scripted answer? The amount of water used depends on the sensor and the exact conditions. Well, yes, of course; I dont expect a specific amount. Just as the amount of gas used by a car depends on the length of a trip and the speed driven, the amount of water used per cycle will vary, but nevertheless we know, more or less, how much gas is used by a Toyota Camry on a trip between New York and the Maytag Customer Service office in Benton Harbor, Michigan. I noted that, if Maytag claims to build high efficiency (HE) machines, then they must be HE in comparison to something, right? -- otherwise how could they claim that these machines used less water? Less than... what?** insisted that no one at Maytag could tell me the answer. He asked, What reason could Maytag have not to disclose this information? I know this isnt the answer you want to hear, but its simply not available. Not even a range of water use per cycle required/solicited/demanded by the sensor? Can Maytags engineers be so indifferent that they never tested any cycle for its water use, but instead they just imagine that, by virtue of its mysterious sensor, it was lower than the use by their non-efficient machines? Your help in getting to the bottom of what felt like an act of stonewalling would be highly appreciated!

Front load washer is four years old. Approximately two years after owning the washing machine it started burning and ripping our clothes. Maytag sent someone out to repair at no cost. The problem stopped. However, approximately two years later it is happening all over again. Thus, there is either a deficiency in the Maytag product or the repair has failed. Maytag will only repair at our cost. True, the washer is four years old but the same problem keeps happening. Plus, that is not a long time in the life of a washing machine. The customer should not be held responsible for a recurring problem with their product. The front load washer and dryer were very expensive. We will NEVER buy Maytag and we will continue to share our disappointment to whoever will listen. It is shameful that Maytag says they stand by their product but when its put to the test Maytag completely fail. Double thumbs down for Maytag and customer service!!!

Maytag stove MGR7662WW - I purchased this stove about 4 years ago. Now, the stove will not light. I called in to Maytag only to be told I must pay a service fee or purchase a repair manual. It’s very strange. My old Kenmore lasted 22 years and here I thought Maytag would at least last 10 years less than half the life of my old stove, realizing products today are not what they used to be. Maytag, the dependability people, I guess that old Maytag commercial where the Maytag repairman is so bored claiming no one needs service for a Maytag product is really false advertising. Buy American products; I’m not really sure who is the current country who is home to the great Maytag corporation. I guess me and my wife will spend another $700 on another brand stove and try this process all over again, hopefully not again in approx 4 years.

I have a top loader Maytag washing machine, Model MVWB835DW4, bought in 11/2019. Five months of light use, the lid cracked. Received a replacement and four months later the lid once again cracked in the exact same spot. Requested replacement parts under warranty and I was told that a service tech must install the lid. Due to health and safety concerns related to Covid, we are not take any chances letting people into our home. My wife and I are 70 years old and are at high risk. Maytags response was they would not send parts under warranty to me and a service tech must install the parts. If I dont let them in by 11/2/2020 (the end of the warranty period) then I would have to pay for the parts. Maytag has the very worse customer service in the industry.

I had six service calls, one was a few months after purchase when under warranty for loud noise. I bought it in 08 and since then during the last 6 months, its freezing in the refrigerator. Service person is upset. I contacted corporate and they do not care and told me I should have bought their warranty. Yes, they had to be here when it was under warranty. Still freezing, they played with air hoses, replaced the temp panel and did everything they can, with no results. Theyre giving it one more try and it is going to be hooked up to the Silverado and put on I-75 with a sign on it. Do not buy from this company. Terrible service. I emailed CEO and no response. I just tossed a tomato and strawberry on the tile floor. Yes, buy American. They moved their plant from Indiana (union) to I think TN for non-union. Well, get what you pay for and the employees get what they are paid for. I work in the building business and everyone knows not to buy this product! Just throwing your money away. One good thing is if you like frozen beverages, this is the product to buy! Never again! Receipts in hand! Romney probably owns the stock! LOL

After 1.5 years, our Maytag bottom freezer ref has started leaking water on the floor. There is a sheet of ice on the bottom of the freezer, and ice in the slots on the back wall. This sounds like a frozen moisture drain. This seems to be a common problem. There should be a recall.

The control panel and the electronic control box had to be replaced after only two years of use. It cost almost as much as a new dishwasher (492 dollars). The model of the Maytag dishwasher is MDB77479SBM3. This dishwasher looks good from the outside and runs quite but the electronics are cheap and cant stand heat without melting. My wife and I are retired and only used this washer about twice per week. It looks good, cost 650 bucks and it is a pile of junk. No more Maytag in our house. We had this machine installed in July of 2014... It crapped out in July of 2016.

I am not complaining at all about my dealer. I am complaining that I also am like the many others with the French door fridge/freezer. The bottom of the freezer freezes up and water pours all over the floor. I thought that Maytag was a good appliance, but also had problems with the pump and drain on my washer. Both of these are only 2 1/2 years old.

We bought our Maytag dishwasher at Sears about 2 years ago. It has never cleaned very well, we have to rinse everything almost to the point of spotless before we load it. Its a water saver, which means it takes more than 4 hours to fully cycle. Just today, I went to turn it on and the start button does not work. I looked it up and found that this is a common problem with new Maytag washers. This is really irritating, considering we paid a lot more for the Maytag brand than we would have paid for something without the Maytag reputation. Live and learn, I guess; we certainly will not be buying another Maytag.

We had a repairman come out and take a torn pillowcase out that was jamming. It worked for a couple of weeks, now refuses to start. We have decided to rid ourselves of the Bravos 300 washing machine and not deal with Maytag any more. I would not advise anyone to buy a washer of this type, as it never really got the clothes clean to begin with.

I have a new HE (high efficiency) washer. It takes getting used to as its a definite change from the old agitating system but I think I like it. It doesnt make much in the way of suds but everything still comes out really clean. The wash cycle is much longer than my old washer but it uses a lot less water.

I purchased a Maytag Bravo HE washer and dryer! The biggest mistake I ever made! Three inches of water is max for a load of clothes! This is max full or actually empty. The washer was a third full of clothes and only the bottom layer was wet when it went into rinse! After pulling a calf I really wanted the top pants washed. Nope. Went in dirty and dry to the rinse cycle to spread the bacteria throughout the load. The soap was still laying on the dry clothes on top. Repair guy spent two hours and couldnt get enough water to at least dampen all the clothes in the wash cycle. I would like to see how much cow afterbirth bacteria was still in clothes. I didnt buy a machine to dry wash my clothes! I have asked for my money back on the pair through the performance warranty. Well see! I am not giving it a star as it doesnt earn one!

Bought all stainless steel Maytag appliances when we remodeled our kitchen in 2010. French door fridge freezer broke down three times. First the fridge lost its temp and we lost our food. The freezer went into overdrive and froze the vodka solid. Second time massive ice build up in bottom of freezer so we had to constantly chip it away to keep door closed. Third time was a repeat of the fridge not working at all and the freezer going insanely cold. Sad to say, we have given up and bought another fridge freezer for $1,500, not a Maytag!On to the washing machine: a super duper top of the line expensive Maytag. At the end of last year it started to make disturbing jet engine noises in spin mode. It for worse and worse so I had a repair man come and take a look at it. He said it would cost over $700 to fix. Once again, we decided to cut our loses and buy another washing machine. I have saved all the paperwork including the repair bills for both appliances so Im good to go on the class action lawsuit.

Less than 1 year ago, my washing machine that my husband bought me was a Maytag Mod #MVWC200XW0. It went. The repairman came and had to put in a brand new capacitor and less than 3 months later, there are two things that are wrong with the washer and I cant use it again. I have to go to the laundromat and take clothes elsewhere to get them done. I took out an extended service agreement in January. Maytag deducted $21.18 from my checking account and they never sent me an invoice for the balance of $42.36. I kept calling and trying to get an invoice. Then on June 25th, I received a letter in the mail that they cancelled my service agreement. I guess this was cancelled in May and they sent me a letter a month later. Now, the repairman was there last night and they could not fix it without us paying upfront and the extended service plan said they didnt even know if we would get reimbursed for any of the parts. This is very poor for a washer that is just a little over a year old. As far as I am concerned, this washer is junk and needs to be junked. My husband got a lemon. I am not putting this amount of money in something that every 3 months has something going wrong with it. I would appreciate a phone call back or something that could be done. Thank you.

If I could rate it lower than 1 star, I would. We bought ours new in 2005. Within 6 months, the main pulley for spinning the drum fell off not once but thrice. The repair tech said that the shaft was machined incorrectly at the factory and the bolt that would normally hold it on was backing out. The 3rd time it happened was close to the end of the warranty and the tech could not make it out before the warranty date. When he did show up, they wanted to charge us. I wound up putting the part in myself. Two months later, the suds alarm came on, which caused the water valve to open. The pump kicked out and the water valve stayed on flooding my basement and the electronics in the washer. This happened twice. The second time was a week ago and I tossed the ** out to the curb. We also have a Maytag Gemini double stove which does not work either. This is the second and last Maytag appliance that I will ever own. They are junk!

I purchased a Maytag refrigerator 4.3 years ago. Model #NSD2572VEW01 side-by-side. Came home to find water on floor. Called for service at a local company. Tried several new parts, only to find out I had a bad compressor. Part cost $358.30 + labor charge which couldnt be estimated because of difficulty with installation. Called Maytag for help, was told FIVE times, Sorry, nothing we can do to help you. Have never had any other appliance in my life except Maytag. NEVER had a problem with anything before. Have washer, dryer, fridge, stove, microwave, and dishwasher. Found the answer to be unacceptable!!!

1998 MAH4000 - I got this unit (used) in 2004 for $400, and it has pretty much kinda been a lemon ever since. I have babied it through until now, though it had the wax motor repaired twice (Im glad I bought an extended warranty from Maytag, but that added $400). Now the motor control has gone out. I like the concept of the front-loader, but my folks Maytags (and my grandparents) have run for 30+ years without any of the hassles Ive had.Granted, I like bleach, so the mold thing has been less of an issue for me, but wow. I have to say I wont ever purchase another Maytag appliance again. Im about to drop the $185 for a new motor (the motor control board went out, and apparently I need to get the new motor and control). Im pretty sure I lost a phase based on the burnt components on the board. Im glad I know a bit about electronics, or else Id really have been in for some money. Boo on this model!!

Do not buy one. Maytag is unresponsive to repairs or parts that are needed. They are not even manufacturing the part that breaks. If you are lucky, you will find out there is someone who will fix the defective computer board... But Maytag will not tell you. We were without fridge for 4 months... They did not care.

Come on people are you serious! Im talking about all those people who give this washer great reviews or even mediocre reviews. This washing machine sucks! Thank God for the glass lid so you can see how terrible it washes. No water in this thing. Clothes that sit on the edge of the bowl do not agitate enough to be washed if there was water in the wash cycle. Bleach that you use in your white wash cycle is left over and gets onto your colored cycle if you wash it the color cycle next. I ** you not, mark my words that stains are left on clothes even in a cycle that has lots of water in it. If you think Im high or crazy take a look at your local Home Depot or Lowes store. Check the area for washing machines that are for sale that have been used. You will find this Maytag Bravos XL machine there. They look good and are practically brand new and they will be there for weeks on and because people return them if they get lucky to return them. I called my store and they refuse to take it back and told me to call the manufacturer. I did just that... I called the manufacturer and they told me they can send out a serviceman to check the washing machine. Butt...and a big butt, if they find nothing wrong with the washing machine that I will be charged a service fee. Bunch of **! For all of us that get stuck with this pile of garbage we can thank the tree huggers for trying to save the world with low water consumption water washing machines.

Maytag Bravos XL Washer & Dryer - After a long 45-year use of our old GE W./D. that were still working fine when we decided it was finally time to upgrade. Big mistake. Nothing but dissatisfaction on every level of complaints by those who registered here before us and then some. This all was noticed almost immediately after purchase, but we lived with it trying not to believe our worse fears. That is until we both started breaking out with skin rashes. Just logged on this site after a Google search... We were shocked and disappointed in our purchase decision. We will join in a class action lawsuit if ever one is initiated... Any lawyers with one of these?

Not long after dishwasher MDB7609AWB2 was out of warranty the START switch on the keyboard would not work. Called dealer and they sent someone out to check for a charge not quite $100. Could not fix it so said it needed a new control panel which with labor was almost $200. Doesnt work so get it fixed. Now less than 3 years later the same thing has happened - wont start. Lousy engineering and part probably made in China to save Maytag money, I feel is the cause. This is happening over and over to those of us who purchased in good faith what used to be a reliable product from a reliable company.

Purchased my Maytag Dishwasher MDB7749SBM on 5/13. 3 weeks ago the panel went out! I found others have had the same complaint on their Maytag Dishwashers too! I also learned this model was discontinued from Home Depot. Is this because Maytag knows this Dishwasher was JUNK and that they allowed consumers to buy this model knowing it had these problems - I believe so! I find it absolutely crazy that Maytag has not issued a RECALL and now I am out almost $700 plus if I get it fixed or buy a new one, I am out even more $$! There has to be some RESPONSIBILITY taken from Maytag!!! This Company was built on an excellent reputation but now this company reputation is considered POOR for selling defective products and doing nothing about it!

I bought this after having a Frigidaire for 40 years and was immediately disappointed upon installation. This OVEN, not a range, was smaller inside and a lot of new pans would not fit! I have replaced the burners and the bulb wiring several times. Would not buy another one!

13 months after installing the dishwasher, the touch pad no longer functioned. Called Maytag 800 number and they said out of warranty. I sent out repair man and he gave me a price for repair totaling approx. $300. Called back to Maytag and asked for a supervisor, she agreed to send the parts for free and I had the repair man install. Out the $120 for the repair and wonder how long it will last this time! I will consider a buying an extended warranty? Next time I will buy a lesser priced dishwasher with a dial, no more touch pads.

We purchased a new Maytag Bravos Washer and Dryer in April 2012. The dryer has been nothing but a piece of trash. It has been serviced 4 times for the same problem. The first time, a thermo element failed and dryer wouldnt heat. Second time, thermo element failed and was replaced. Third time, thermo element was replaced and flame scoop was replaced. Service man called the factory to find out what could be causing this problem. Factory service recommended replacing gas valve. The valve was ordered and replaced. A couple weeks later, the thermo element has failed again, and of course, the failure happens on a weekend. We are a retired couple, so we might only have a couple loads of clothes per week. All of the repairs have been covered under the first year warranty. When you spend $900 for a dryer, you would think it will work for at least the first year!

We bought this Maytag MFI2269DRM01 Fridge/Freezer in June 2016. We have nothing but trouble. First the center rail holding up the Fruit/Veg drawers snapped within a month then the freezer drawer would not close properly which gave us all sorts of problems (door open lights flashing and fridge staying on longer. Lights not working etc.) The service tech came out and tried to fix it and went away saying it was not repaired that he would need a new freezer drawer. In the meantime I had to push the drawer to try and get it to work right. Now the handle is loose and the stainless steel front of the drawer is damaged by pushing it in so much.This repair started in November and now it is the end of March. I asked them to replace the complete unit but they say that the warranty is just to repair. It seems like they have no parts to fix this. Then the new center rail snapped again!!! When they sent the part out to me to install, I found the main frame of the Fruit/Veg rack at the back had snapped. Everything is brittle plastic with not enough support. (The only vegetable that I think I can put in the drawers is mushrooms.) I thought by buying a Maytag that the name sold it. What a piece of junk it is!!! Will never buy another Maytag product!!!

I purchased Maytag Washer and Dryer 3-4 years ago, upgraded to the premium washer and dryer, SS drums and have been dissatisfied from the start. The washer was extremely noisy; we were told this was normal. The dryer began making strange noises just outside the warranty period, and the belt and pulley had to be replaced. I was shocked at the cheapness of the pulley design, but the replacement part was of better quality. The washer began making a horrendous squeak shortly afterwards, again, outside the warranty period. The repairman said that they were all like that, Maytag used inferior transmissions and that it would be cheaper to replace the washer than repairing it. My mother had the same experience with a similar model. Needless to say, I will never purchase another Maytag product. FYI, there are only three people in our household, all adults, light duty use.

Same as everyone else, ice freezes up on the bottom and water runs out all over the floor, ruining my new floor. Whole kitchen was new including all appliances. Maytag is ruining my floors. Can find no drain pipes so not sure where the water is supposed to do. I think they forgot to install one. But I am getting pretty sick of seeing my floors ruined and stepping in water.

I purchased a Maytag Gemini April 22 2017 and I am very unhappy with it. The ovens are not working properly. I have thrown away so much food because the ovens won’t hold temperature. The display says it’s the temp. I set it but the temp keeps dropping and rising causing the bottom and top to burn and inside not to cook. Both ovens are doing it. Had a repairman come day before Christmas. He said there is nothing wrong. He said set temp, when preheat beep goes off wait 15 minutes for it to cycle then insert food. I tried this Christmas Day. Oven is still not working and again I threw away more food. I am so disappointed in Maytag. Serviceman is set up again to come out next week. I think I got a lemon. Please. I think they should replace the whole range. It’s not fair. I paid so much for this range and can’t use it.

If you have a second floor laundry room, DO NOT, and I repeat, DO NOT acquire this washing machine!!! The Bravo MCT model washer is TOO loud (during spinning cycle), and for some reason, the clothes come out all tangled up. Some cycles are a waste of a cycle, and most cycles take a bit longer than my former washer. I miss the cycle choices I used to have on my former GE Profile washer (GE does not make that model anymore hence my changing brands). For the most part, clothes come out clean; thats why I give it a two-star rating instead of one. The dryer: Must dry every load in low heat so it doesnt come out extra crispy and wrinkled up. Although I generally have to run a second drying cycle, low heat does work great and the clothes come out ready to be folded/put away.

I have several rental properties and every Maytag dishwasher I have installed in the past three years does not work. It is crazy that a national class action lawsuit has not been filed. There would have to be a large sum of money in fees for the firm that takes the case on. I am not usually for class action lawsuits but this is a known problem that Maytag refuses to acknowledge.

I waited my entire life to age 47 to purchase a brand new matching Maytag washer and dryer. I was thrilled. That was August of 2012. 3 years and two months later, the $800 dryer (MEDE201YW) loses the entire control panel and Maytag refuses to offer any assistance. I deliberately purchase Maytag with its stellar reputation, an American based company only to be more disappointed in the product and the company than in any other appliance Ive ever purchased.

I bought my fridge (Maytag French Door Fridge MFF2258VEW) in September 2009. It took forever to get it and when it was delivered, the door was dented so I had to wait for a new door to be replaced. The fridge stopped cooling just before Thanksgiving 2011. I had to throw out a lot of food. It was the circuit board and that was covered under the warranty. I noticed a couple of months later that the freezer was freezing up again and was worried that the fridge would go out again and in February 2012, they came out again and it turned out that the freezer had been put back incorrectly and the freezer gasket didnt fit right and thus, the freezing up on the circuit board. Now it is May 21, 2012, and I came home for lunch to find the fridge not working again! I cant get anyone out to fix it until Wednesday, the 23rd. Now we are in warm weather and I just went to the store and had a full fridge. I still have the warranty and will for another 14 months. I think if this continues to happen and when the warranty is up, we will have to replace this fridge. I can tell you for sure that it will not be another Maytag! What a piece of junk!

I really liked my Maytag Bravo X washer. Until, at less than 2 years old, it started having issues. It all of a sudden starting sticking in the spin mode, then it wouldnt turn off even though the cycle was complete. I have to pull the plug out of the machine it to stop from continuously running. I was charged $104 to have a certified tech come out for 15 minutes and recalibrate it and it worked for another month. It started having that same problem again and now, I have learned I need a new control board, which costs over $200, plus labor, over $60. The Maytag service rep I spoke with was very pleasant when she told me she spoke with her supervisor and told me there was nothing they can. So now I dont like my pretty new machine at all, and have to decide if I should stick almost $300 into getting it fixed again, or buy a new washer, NOT A MAYTAG! As I voiced my complaint on the Maytag website I saw that there were many of the same complaints about the faulty control board and am wondering what does it take to get a recall?

We purchased a Maytag gas range, only to have the paint wash off the front trim of the oven door. The digital panel went out in the second year of use and is apparently expensive to replace. After going through reviews by other owners and discussions with repairmen, it was determined that these panels only last about a year and are defective. This problem is extensive with Maytag. My brother was a repairman for them and dropped them due to poor quality of workmanship in appliances and their dishonest approach to warranties. I should have known better. Dont ever buy Maytag!!!

I have not been satisfied with this Bravo washer since purchased 4 years ago. I have been holding back anger, hoping things would somehow improve. Clothes are never really cleaned, cant even fill washer with very many clothes because the washer goes off balance. It takes a lot longer to do laundry. Clothes spin so fast they are in knots when I put them in the dryer. I always have to iron clothes. Today, well today we have a leak coming from under the washer somewhere. So please tell me, what is the advantage to having a HE washer again? By the way, no warranty since its been 4 years. I will never buy another one.

Washer leaves spots on clothes and massive knots in clothes. The serviceman has been here twice since we bought it and was told to use extra wash option and heavy load wash with fabric softener option as well, and to only use about one tablespoon of detergent. So much for the green option! Results, still washing clothes 2 or 3 times per load then into the dryer. Tried an experiment - washed a pair of my daughters white capris and then washed them at a friends house while water was saved in a separate tub. Holy crap, the dirt in the water. Do not buy this machine. Not even if it is offered to you for free.

Great when it works properly and doesnt leak! Quietness, cycles. Everything that had to go in went in, well laid out. Stainless steel, clean, good looking. Anything with the Maytag name doesnt last any more than a couple of years. Gone through a washer and dryer with no help from Maytag. The dishwasher was replaced by Maytag because the main circuit board was on backorder for more than 5 months. Washer was replaced with a Samsung. If I had to replace the dishwasher out of pocket I would go to Korea or Europe to do so. Maytag, what a huge fall in quality and reliability!

Angie from WFCC-PREFERRED APPLIANCE REPAIR had the wiring harness delivered to her personal address and then came out and installed it that same afternoon past 5pm to ensure I had a working stove. She explained what had happened with the parts delivery mixups and also delivered a $100 gift card. Very happy to have my range working and all has turned out well. I am a long time Maytag customer and its great to have all my appliances back.

Centennial HE top loading washer - When I put the HE Tide powder in the washer, it does not always rinse well. I have to rewash often. I use very little soap.

Dont buy their washers. Plain and simple. Will never ever buy Maytag again. This washing machine is garbage and I paid a lot of money for it. 3 months out and it had to have the entire circuit board replaced. I was assured that this was the issue. It has never cleaned our clothing, in fact, they come out twice as dirty and with soap. Weve used the Affresh, weve put as little as 1 tablespoon of detergent, weve triple washed several loads and still ended up having to wash them by hand in the tub. Changing the circuit board did nothing. Weve tried setting it to max fill (which it does) and everything still comes out the same. Its not the water, its not the water hook ups (previous washer worked great but was old, should have kept it). This is the worse product that Ive spent almost a thousand dollars on. Its a paperweight. On top of this, it twists your clothes into a mass. I expect companies to be honest about their products and provide what I paid for. How many times does this washer have to be fixed before you will call it a bad design? Im having to literally do all my laundry by hand for the last 8 months. I want my money back so I can buy a good quality product that works. I could have bought a $300.00 washer that would have done better then this. You want more proof, go read their Facebook replies to all their posts. Its all complaints about their washing machines. It would be nice for once to see a company fess up and say they made a design error. But that wont happen. Their money is more important.

I have a front loader dryer, model number MAH5500BWW, serial number A9147862ec. All of a sudden, I found water on the floor and after opening up the front door, I see where around the part that sticks of on the inside of the door, there is a big piece of plastic that has broken off and cracked all the way across the bottom of the door and is missing. It is allowing the water to leak down the front of the bottom of the washer and onto the floor.

I purchase my Maytag Bravos washer from Sears in May 2011. In February of 2014, I started to get the UL message, meaning unbalanced load. I would re distribute the clothes and sometimes that did the trick and others not so much. Now every load comes up UL. I tried putting the machine on the drain and spin cycle to at least get the clothes a little bit drier but the UL message still appears and the clothes are still soaking wet. I lifted the washer up and there is an oil/grease type spin pattern under the washing machine. I called Maytag today (which is now Whirlpool I guess) as the washer has a 10 year warranty on the drum and motor. I was told a service call is $129. When I mentioned that I had Googled the product and saw many reviews with the same exact problem, she stated the Bravos has no common complaints. From what Ive read, it seems to me it would be more cost effective to go out and buy a new washing machine and it obviously wont be another Maytag or Whirlpool.

I loved my refrigerator because it was plenty of space, energy efficient and ran like a top even after 20 years when we sold the house. I look forward to buying another one when I buy my new home.

We purchased a Maytag refrigerator, model #mf12269veb on 2/1/12 and for the past few months it has been leaking water out of the bottom freezer unto my floor and ice is forming inside the bottom of the freezer. I have read many complaints about this and if there is any recourse to this problem please let me know. So disappointed with this appliance.

Bought this Bravo washer from a Sears Outlet Store. Had trouble the first 2 weeks and did all the troubleshooting to no avail. Just when I was ready to return it to the store I decided to try one more thing. The guys who hooked it up had reversed the water hoses - cold was hooked up to the hot intake, and hot water was hooked up to the cold intake. Took all of 5 minutes to switch the hoses to the correct intake and the machine works like a charm. MAKE SURE THE WATER IS HOOKED UP CORRECTLY.

Very disappointed with my 2014 purchase of model MDB8959SBS3 dishwasher. In fact it is no longer in service. We used the dishwasher approximately twice a day. The wheels on the pull out racks starting falling apart in the first 6 months. Then the soap dispenser failed. It would not shut. We replaced both the wheels and the dispenser only to find ourselves with the exact same problems in a matter of months. My hubby got really good at fixing both of these items. The final straw was earlier this year as when we turned it on the motor/water pump started making a screeching sound. Never had to replace an appliance that was only four years old in my lifetime. Just very disappointed with the quality of Maytags dishwasher.

I purchased the Maytag Atlantis Washer and dryer in 2004. I had the washer transmission replaced in 2006, I believe. For about a year now, the washer makes an awful screeching noise. I am not sure if its towards the end of the spin cycle or the rinse cycle, or both. In addition (and over the last 3-4 years), the dial sticks or stalls every delicate cycle. It will stop during the initial agitating and all you can hear is a ticking noise, in which you then have to manually give the dial a slight turn for the cycle to continue. It does it once on the light delicate and twice on the normal delicate. It really is a shame that Maytag is not acknowledging all of these problems as it is not feasible for most people to have a spare $1500 kicking around for a new washer and dryer every time they unfortunately buy a lemon. My previous washer and dryer were 25 years old and still working perfectly when I decided to part with them because they were fairly small. I dont even ever recall having any issues with either one of them in the whole 25 years that I had them. To see all of these complaints makes me more irritated with my appliances and my selection!

Bought a Maytag Dishwasher (Model No. MDB7749SBM2) in Sept. 2013 and I am in need of repair for the control panel. The dishwasher is in a vacation house and isnt used on a daily basis. I always thought Maytag was a reliable product but Ive been reading the reviews and the control panel is a problem on relatively new units. How do they get away with this. The unit was around $600 and now Im stuck with a big repair bill... and it appears, from what Ive read on this site that it is a common problem. Maytag has replaced the control panel part and, as far as I am concerned, they should have provided them to all the consumers who were stuck with the defective ones they sold us in the last few years. Now we all know why we dont see the Maytag repairman sitting around with nothing to do on TV. Hes working his ass off trying to fix the dishwashers.

We bought our Maytag Bravos in December 2010. Four months out of warranty, like many other complaints Ive read, we started getting the loud jet taking off noise from the laundry room. Now we are having issues with the lid lock not allowing you to get to the clothes. This machine tries to spin three times and then locks up. It literally locks the lid and will not allow you to get to your clothes! For a machine to fail just four months out of warranty is a joke! After investigating the problems with the machine, it will cost us more to repair than what we originally paid for the washer in the first place. Give me a break! There should be a recall and Maytag should have their feet held to the fire to replace these less than adequate high-dollar machines!

I have had this machine for 15 years and never spent a penny on any maintenance, I love it. Some things are worth it and it still has a stylish look and cleans great. The only thing I would change is if it didn't have any the middle washer paddle so it would have more space like the newer models.

I purchased my Maytag Refrigerator in Feb 2013. It is model MFF2558VEW7. It has the French doors w/ freezer at the bottom. This past week, I lost everything in the freezer. I call the Home Depot where I purchased it and they said that I have to call Maytag. I did and they sent a repairman out. It needed a compressor. After only 8 months, the compressor goes out? Why should this fridge be repaired and I not be given a new one? With all the problems with the Maytag, there needs to be one big class action filed. I asked for a loaner because it would take up to five work days for them to order the part. The answer was, We do not provide loaners.

I purchased a Maytag Dishwasher in March 2013 and the control panel failed in July 2014. I, along with hundreds or thousands of others it seems, discovered that this is an extremely common issue with several models of Maytag dishwashers. Rather than standing behind their products and making it right for their customers, Maytag is hiding behind their one year warranty and refusing to do anything about it or even admit they installed thousands of FAULTY control panels. This has been an expensive, infuriating issue to deal with and I have never been so dissatisfied with a company. Bottom line, they made a bad product that should have been recalled. It blows my mind that they are getting away with this. I wish I had known the recent changes in Maytag/Whirlpool and I wish I had done my research prior to the purchase.

Have read others reviews and experiences and wish I had visited here first. Our first Maytag washer and dryer set lasted over 25 years with only minor repairs until the transmission started to leak grease and was uneconomical to repair. Our second set only lasted nearly 10 years and were obviously lesser quality. The wife decided that she wanted the best and high tech version. She really liked the features of the Bravos 300. What a mistake! Not even three years old and she has been dealing with the noise and the problem with constant unbalanced loads, intermittent error codes, odors and the forever cleaning requirement. The whites were intermittently getting rust stains until I determined that the underneath side of the top cover around the bleach reservoir had rusted out big time. I replaced the top cover for over $125 plus an afternoon that I will never get back. (Out of warranty, of course). Today the wife called me to say that the washer would not complete the rinse cycle and she could not reset it. We had to pump out the water and pick the wet clothes out. A grinding sound is coming from near the bottom of the machine and sounds expensive. The service man is scheduled to be here day after tomorrow to give me the bad news. My next washer purchase will NOT be a Maytag or any other high tech piece of crap. Simple is better.......

Due to our previous washer breaking down, we had to purchase a new washer. We have always been loyal to Maytag since we were always pleased and satisfied with the performance. However, this new washer does not deliver in performance, cleanliness, energy savings when cycles take much longer and you end up maybe not using as much water, but our electric bill has gone up considerably. I have nothing good to report about this washer. We purchased it back in April of 2013, and Ive given it the benefit of the doubt by experimenting with all the different wash cycles. I am just not happy with it. I so want to trade it in for a front loader and give Maytag one more chance.

The washer stopped and displayed F51. It had that growling, horrible sound like it was dying. After restarting and trying everything, including going back to Lowes to see if a serviceman could fix it, with no luck, and father reading all the reviews on the F51 error and all of the displeased customers we divided after two years on a $900.00 machine, we would tear it apart and fix it ourselves! If possible and if not, what are we losing? Nothing! What we found was clothing between the outer casing and the drum preventing it from spinning. Unfortunately, we did not know how to get to them. With a lot of effort, we got the leggings out that was causing the drum not to spin. I am sure there is a lot more socks and a pair of fairy wings that I never found after Halloween in there. If there is anyone out there who knows how to get the outer casing off of the drum, please let me know. After removing the tights, I no longer have the error code F51 and my washer now works. I just wanted everyone with F51 error code to know it goes away after removing the clothing that gets stuck between the drum and the outer plastic casing around the drum.

I bought a brand new Maytag bottom freezer fridge on Aug. 12th, 2012. The main compressor went out on Memorial Day of 2013. I contacted the store I bought it from; they referred me to a local repairman who fixes Maytag. I talked to him and told him the problem along with the make & model of mine. He ended up telling me what exactly the problem was, & there were about 5 people ahead of me with the same fridge, & same problem... all main compressor problems. Check this out. The compressor part is on back order... so now I have no fridge, & Im stuck with this piece of crap, until MAYTAG finds a compressor to ship to the local repairman. - Last Maytag product I will ever own in my lifetime!!!

What happened to the days of buying a washer/dryer and having them for years! To spend a thousand on each and have holes in the bellow causing dirty water to Empty on your floor. Not once replaced, not twice, 5 times!!! Now Im looking to buy another. Old school for me...

We can do nothing at the control panel even though the drum light will come on when the door is opened, we cannot turn it from the control panel. After a varying length of time, a fault code of F70 is displayed (which is not covered in the owners manual), the dryer can then be started by depressing the power button and all functions seem to be restored.

I had a Maytag dishwasher for 17 years, and it has still worked fine when we moved to another state. At the end of 2010, I bought a new Maytag (1) because my old one performed so well and (2) we left it at our old house. Well, slightly over two years later, this piece of junk (Model MDB6709AWAQ1) needs almost $300 worth of repairs. The repairman said they are no longer made to last and have been that way since about the year 2000. All of the inner workings are run by electronics which only last about two years. I said, What happened; the Maytag repairman got tired of sitting around doing nothing? I would never ever purchase another Maytag dishwasher, or any other appliance made by them or Whirlpool which took over Maytag.

I loved my first Maytag combo unit and when that quit I bought another Maytag. The Neptune is a front load washer. I immediately noticed the door gasket getting moldy. I contacted Maytag whose response was leave the door open. Well, I did that and not only did I still get mold, but the light burned out. I recently started having trouble - the water doesnt drain and the clothes are still wet. Rather than have it repaired, I elected to buy a new washer/dryer unit. I would NEVER again have a front load washer and certainly not Maytag.

Bravo XL Washer & Dryer - I have owned this set for just over 90 days and have called Maytag several times just to get insulted. The customer service representative is not helpful at all, and tells me that I am not using HE detergent or that I am using too much HE detergent. Furthermore, they tell me that if a service technician comes to my home and nothing is wrong that I will get charged. So much for the extended warranty and what is wrote on the Maytag site. I explain each time that I am using name brand HE detergent and the recommended amount. The soap dispenser in the machine provides a fill line that I fill to. I have even tried using less detergent as recommended by the appliance store that I purchased the machine from, and still the washer does not clean my laundry and leaves residue on everything. I have even tried using the extra rinse, and extra heavy soil setting which does not make a difference at all.The other concern is that the clean washer feature light flashes weekly. I have purchased the cleaning tabs recommended to clean the machine, and run this clean cycle every time the light comes on. The dryer does not work all that well either and shuts off before the laundry is dry. Sometimes the dryer will show an error of airflow restriction or low airflow. This is confusing because the dryer vent and hose are clean, and the lint filter is also clean. This is so disappointing because I thought Maytag had great products. However, as I read other reviews about these machines and the customer service representatives it seems that there is a systemic problem with the machines and the customer service representatives that needs to be addressed by the leadership at Maytag.

We have owned a Maytag Commercial Centennial washer for 4 years and made the mistake of not buying an extended warranty as we thought Maytag was dependable and a reputable company and thought the manufacturers 10 year limited warranty would cover us. Washer would not spin clothes properly, started making loud noises, lid would not always unlock as time went on, and finally it broke and soaked my tile and it ran through my wall into my hall carpet. Called Maytag and was told we didnt have a 10 year limited parts warranty 6 times (we still have the book that says we do), they offered us a 1 year full warranty for $320.00. We purchased the warranty 11/04/16, Called Maytag as no one knew where the parts were and was told service plan is through AIG. AIG couldnt tell us where the parts were either and when I asked for our refund and we just buy a new washer they advised me they would have to prorate it.Now I feel held hostage. Parts finally come in and Maytag Certified repair man comes to repair machine on 11/30/16, only to be told they could not fix our washer as the screws and transmission rotted and fused to tub. Call Maytag as this should be under my warranty and everyone insists I dont have a warranty. Filed complaint 11/30/16, they sent me a survey on 12/2/16 and I filed my complaint again on the survey. No call from Maytag. Call back on 12/06/16 to be told the survey was them closing my complaint. Now they escalate my complaint and will be called in 48 hours and give me an email address to email my pictures of my warranty. Surprise no call back, so I called them again 12/08/16 and I am advised it takes 3-5 business days. Ask for supervisor and he told me even if I have warranty they will only cover the basket.I will have to pay for technician, and other parts. Still no info on my complaint and you cant talk to anyone just have to wait. I emailed Jeff Fettig CEO of Whirlpool (Whirlpool owns Maytag) as well on 12/6/16 a copy of my complaint with pictures of warranty. The bottom line is Maytag sells junk and their customer service is worse than their product. After being without a washing machine since 11/04/16 we will be buying something Whirlpool does not own which is very limited which is why they can get away with making junk.

Bought our washer dryer set from Sears in the fall of 2010. I had reservations from the start as the machines were new and the salesman was really pushing this set (on sale), with all the customers, even offering extra discounts on these models only, if customers bought that day. Apparently, they had overstock and were trying to sell them all ASAP. That was a warning to me but my husband convinced me that I was being overly suspicious. We had previously owned Maytag machines for 20 years and loved them. So I agreed. Well, I have been cursing that decision ever since. You have to hand wash/prescrub any stain on clothing, even a little make-up like blush or a little mud. Then you have to put up with an inflexible system that wont allow you manual options regarding spins and temperature or times, etc. Its all programmed. Then you put up with clanging spin cycle as it bangs against the wall. Then you pull out very wrinkled and not always cleaned clothes only to begin the most frustrating dryer experience ever. It has a mind of its own. It can actually keep spinning as it keeps adding dry time and the clothes never dry! God help you if you have a regular load. All your clothes will get stuck on the little ledge. They stay there in a heap as the machine spins and spins.The solution? You have to add a bunch of dry towels to create a lot of mass so that it keeps your laundry from getting stuck on the side. Then you have to repeat this several times cause it doesnt dry well. I will never ever shop at Sears and I will never buy Whirlpool or Maytag again. I am now saving to buy another set.

After reading several of the reviews, it looks like Maytag doesnt get it - or maybe they do and its a plot to make more money. Our dishwasher model MDB8959FSZ4 was installed in Dec. 2016. Within the year, it started leaking. After many service calls it was determined that the arms holding the upper rack were not installed properly and were pushing against the door and water was coming out. After that was replaced, weve had 2 years of relative good use. Now, it wont empty and that started after smelling something burning. The burning smell has gone away but it wont complete a cycle. Service tells us its the drainage pump and that will cost nearly $500 to replace. We wont be spending another dime on this piece of crap. Well replace it with NOT A MAYTAG. Im wondering if it has to do with the control panel as many others have mentioned. We dont care to find out at this point. We are buying something else.

My new fridge iced over top to bottom. It started making horrible noise then ice maker stopped working. Called MY repairman. Thats when I found out about all the ice. He told me to thaw out and hed be back. It thawed out and then freezer went out. ALL my freaking meats and frozen food had to be thrown out. Now water keeps Flowing out on my NEW tile! Called my repairman back. He came back then informed me it was junk! He said several other customers having same issue. My daughter has the same refrigerator and it broke down just like mine! My repairman also said a big issue with your junk was you used parts from other brands to fix!After reading all these complaints I can see no sense in calling to get it repaired. Its obvious we are all having the same issue. Maybe someone from your ** company could check them out. I dont have the money to buy another fridge! My 85 year old uncle with Alzheimers lives with me and I dont want him to slip on that water and hurt himself! I think all of these complaints need to go to BBB. Thats my next step. I believe you need to recall this junk or give us our money back! I need you to respond or Im going on blast to let everyone know how you treat your customers.

We purchased washer at Sears 6 years ago. Have had same issues for 5 or more years. Sears has been out to check it 6 to 7 times! They clean it out, tell me to use (expensive) Affresh tablets monthly, problem solved but it never is! When we run our washer and walk in laundry room it smells like a sewer. If we open lid its even worse. I use Norwex all naturally, biodegradable laundry detergent. There is nothing Ive done to create this smell. Its a manufactured problem that probably relates to ALL the other issues with this crappie washer that Maytag will do nothing about. I called Sears for 7th or 8th time, said they could send someone out AGAIN, I said thats a waste of my time and yours. They told me to call Maytag. They wont do anything (warranty is up). Of course there are NO ISSUES OR RECALLS on this washer and obviously there should be with not ONE good review! Im angry. You all should be too. We paid good $ for a product that used to have a good name and they are screwing us. I think we should ban together with a class action lawsuit. Please give me your thoughts. They know something isnt right and they shouldnt get away with this.

It’s a nice look to your kitchen first, and an easy clean. Works great for heating up stuff in a hurry and makes popcorn perfect on the popcorn button. Does ok at melting things. I have been happy with mine for 3 yrs so far.

I bought the dishwasher (Model MDB7749AWM) 15 months ago and paid $490.00. I had to put a new console in it ($245.00) on 07/16/2012. So that’s $735.00. Two days ago, the console went out again! I’m not putting $245 more in it! I called Maytag’s office. They more or less told me that was my problem! I am throwing that piece of junk away! And I’m buying a different brand. Maytag does not stand behind their product. Last Maytag I will buy! Warning! Do not buy Maytag!

I have had this washer 4 years...I bought this washer in May 2016. It makes 3 very loud noise as it moves into its next mode/cycle. Found out this is normal. IF, it is close to your living room, IT is loud.. I called again, saw that it was not filling up. 1/5/2017.. IT will NOT fill up to wash my clothes properly, clothes were still dry!!! Came out, (they sent a company near my area), said everything is right. I have tried, by sending messages, many times to get them to check. No one seems to care. The machine allows water to go out the bottom, rather than fill in the machine. I watched it myself. THERE should be a recall on this machine, definitely, something is sooo wrong.. I NOW have to put it on BULKY SHEETS full time, to get my wash clean.. NO energy savings there... BUT my clothes are finally clean!! Seriously, something is wrong...

Its a water saver model, so to really rinse the clothes of soap from the wash cycle you have to give it an extra rinse, which the machine has made available. So I do not know how much water it really saves.

The soap dispenser along with the port it slides in becomes molded and is not easy to clean, front loader. I never had a front loader washer with this moldy problem. I have been cleaning it at least once a month,

I have only had this machine a few months and am completely dissatisfied. It sounds like a jet taking off and uses so little water. The clothing does not come clean and wrinkles are close to impossible to iron out.

March 31, 2013 a Maytag front loader washer series 2000 was purchased. In January an error code E4 and F3 kept stopping the washer. Service replaced some minor part, worked for a week. Then service replaced a circuit board - worked fine for a few months. About June of 2014 the codes came up again. This time Service wants 430.00 for a 700.00 dollar washer to fix a continuing issue. So I decided not to spend the money. I could buy another washer, different brand of course, and try and fix it myself. I removed the top and the bottom front covers. The 3 wires going into the circuit board that was replaced were loose, barely plugged in. The catch all at the very bottom right had derbies and coin in it, cleaned that out. Looked at the motherboard with a magnifying glass. It had no bad solders, cracks or burn marks, so I proceeded to run my hands around the entire drum inside... and in the back side where you can’t really see were some more loose wires.... tightened them. Now with the spin rpms you can understand how things shake loose, I always look for the common sense issues.... I am currently on my third wash load. It runs smoother and quieter than it did when it was first installed. Point is the Maytag service sucks and with only a year warranty from the manufacturer. What did I have to lose to try and fix it myself. I am sure this is happening with a lot of other people. The odds of a motherboard or a circuit board going bad in such a short time made no sense. So check all the wiring FIRST. Make sure everything is securely plugged in. I would not recommend anyone buy a Maytag or Whirlpool (owns Maytag) for their reliability or service.

After 2 LG refs and 2 Maytag ref. fridge, I would not recommend either one. My Maytag need a new compressor. My Maytag ref only lasted for 6 years! The main circuit board failed. I decided to get a new fridge from Sears rather than going back to Home Depot. I decided to get a new fridge in Sears rather than going back to Home Depot. The extended maintenance is more expensive at at Sears. In summary, I have only been using the Sears for 3 days now. It is too early to write a review on the Sears fridge.

Bought in July 2014, third service call already! To replace my 6 years old Maytag Centennial thinking I was doing a good thing to upgrade to an HE... HA! Jokes on me! Washing machine: Water level. How can you wash clothes in 1 inch of water??? Noise. Very noisy at every cycle. Shakes and easily unbalanced. Clothes are still dirty after wash (obviously if not enough water). Dryer. Noisy with sporadic blower sound (like a plane taking off - high pitched). Three service calls in 6 months??? 2 calls for cable suspensions and now waiting over a month for the tech to change the drum completely. Good thing that I took an extended guarantee, for an extra $300.00!! After Ive read the over 400 complaints about this product, I really feel like I got screwed! My last Maytag EVER!

MCBH979SAB0 - I am also frustrated with Maytag for the same exact problem... the control panel and the dishwasher not working just after our year warranty went out. I purchased this product because of a recall on my former Maytag dishwasher. I was told I should purchase this new model to replace it, only to get fooled again. This seems like BAD business on Maytag! How can we get an official complaint to someone who can fix this? Why would a company like Home Depot continue to support this business!!