My 20 yr old Kenmore washer broke last month so I replaced it with a Maytag I bought from Lowes. I wanted a simple washer that would maybe last 10 years. The Maytag has a sensor for everything. So you can’t fill the washer, it determines how much water to use and it never fills enough to cover the clothes. It doesn’t agitate really. It’s more like a slow on & off movement. It does everything in an on & off way. The water fill goes on & off, it “washes” on & off. Even the spin is a spin, slow to almost stop - spin again - almost stop - spin again. It also stops filling if you open the lid, I tried to let some water fill before adding clothes (so the liquid detergent could dilute a bit) but every time I opened the top there was no water in the drum, I heated the water running and the drum was wet but it wouldn’t gill at all. I think it only puts water enough to “sense” the clothes have been soaked. I will call Lowes and try to return it.

I purchased my Bravos washer in 2011. Three days before the warranty was up, the motor went out. It was leaking oil and had to be replaced. Two days later it quit working again I had to have another repairman out and found that the gear shifter had popped off so he put it back on and charged us 85.00. Luckily my husband watched him repair it and knew what to do if it happened again, which it does just about every 2 or 3 loads so I have to pull it out and pop the ring back on. I waste more water than I save with this machine. I have to drain the water so I can move the machine out and start all over because they didnt wash, and that wastes more soap. I would get laundry done cleaner and faster if I beat it against a rock. This is the worst washing machine I have ever owned and I will never buy a high efficiency washer or another Maytag again.

Worst washer ever. Wish I had read all these reviews before I bought. I have had the same poor experience. Laundry doesnt even get wet while being washed. Agitation does not affect laundry. Just moves back and forth under laundry. Clothes do not come out clean. Feel I was ripped off.

Purchased this unit back in November 2011. Sometime this year it started leaking water just like many others from the freezer unit onto the floor (many times large puddles). Im tired of the permanent towel on the floor to absorb the water to prevent a potential slipping hazard. I too went online and found a very nice video on youtube which showed how to disassemble the freezer compartment. Took everything apart and noticed that there was water frozen on the supply line. Melted this and put everything back together, for about a week there was no water leaking so I figured all was well. About a week later the puddle was back so I sent an inquiry to Maytag and let them know I had an image of the issue and asked if it was covered through manufacture warranty. Here is their response: Your email is extremely important to us here at the Customer experience Center and we sincerely apologize for any delays in responding to your email. We are working diligently to respond over the telephone and through email to all of our customers. We are sorry to learn of the problem you are experiencing with water leaking from the bottom of the freezer. Unfortunately, we are unable to determine from this location the exact cause of the problem. We recommend that you contact a certified technician for an accurate diagnosis. Once the problem has been diagnosed, please contact us back so that we can review the concern further to determine if assistance is available. For your convenience, we have provided below service providers in your area that you may contact for service. Aries Appliance Service (925)367-7708, Vigil Appliance Service (925)371-7701. You are a valued customer and we do apologize for any inconvenience this concern has caused. We invite you to contact Maytag again either by calling (800) 344-1274 between 8:00am to 8:00pm EST weekdays or by emailing whenever the need arises. When calling please press the available option or stay on the line to reach a representative.Frustrated I went online and found this forum where hundreds of other people had the same issue and that many of them were resolved by the new P Trap. So I watched another video by the same guy on youtube that showed how to replace the P Trap. I went online and found the replacement P Trap Manufacturer model # w10619951. One of the comments there actually said to call Maytag first as they were able to get a replacement P Trap for free. I believe if it was under a year old they would also pay for the labor to have it replaced. So this morning I called Maytag, the first guy Jim said I would have to have a certified Tech come out (76 dollar service fee, plus whatever the labor would cost) and Maytag would cover the cost of the part. I asked Jim if he could just send me the part and Ill do it myself, he reassured me that he could NOT do this and that the system was very specific. I told him I did not understand that a bad design and known quality defect, why should I have to pay several hundred dollars to fix? He told me that was the way it is. I asked to speak to his supervisor and put me on hold. Not only was the hold music extremely obnoxious but there was a loud humming noise as well, I waited for 10 minutes hung up and called back. I spoke with Maggie this time. I told her I wanted the part sent to me and if she couldnt help me I wanted to speak to a manager. She said she did not have the authority to ship me the part without approval. She said she could ask for approval and after waiting for about 3 minutes she came back on the line and said she spoke with her supervisor and that they would be sending me the replacement P trap today via FedEx. Had they not sent me the part my next stop was going to be the better business bureau..

I had a problem with my 1 year old oven. I scheduled an appointment and no one showed up. So I fixed it myself. A week later they called to schedule an appointment and I told them that they were scheduled for last week. So their response was OK, I dont need them anymore - goodbye. The parts are under warranty so I send them the part I replaced myself and the invoice for the cost. I didnt get a response. So 3 months later I send a second letter. Three more months and still no response. I can remember when Maytag had commercials showing their repair sleeping because they had no work to do. Now, their products are failing and their entire service depart is asleep.

Purchased the Maytag MMV405DS Microwave and matching refrigerator from Best Buy in 2016, they were exactly what we had been looking for. Little did we know of the problems we would have with the microwave. At the one year mark the infamous open/close door problem begin. Luckily we were still within the warranty period since it was repaired at no charge. However six month later the problem re-occurred, we are now out of warranty and have little recourse. Maytag should have by now have come up with a fix. I find it hard to believe they are still manufacturing this microwave and selling this product knowing it will fail. We have little choice but to replace it with another brand which will not match. Suggest anyone looking for appliances stay away from Maytag.

I bought my first Maytag French Door fridge about 7 years ago. When it was two it started running water on the floor. I paid a service guy to tell me a tiny little drain in the back clogged up and stopped coil defrost water from draining out. He fixed it. A year later, the fridge stopped cooling but the freezer was cold. I hired another service man who charged me a mint to diagnose that a fan that blows cold air up into the refrigerator failed. Rather than pay him again, I ordered the part. Heres the joke--the part wasnt available. An older part was substituted. Why? The first fan motor was small to make the energy start requirements--but it was too weak to be reliable. The new motor was an earlier model--almost twice as large and powerful. So much for Energy Start. At exactly 5 years and six months, the compressor went out. Im on year two with the new one. I said to myself they cant all be that bad. Now it is leaking on the floor. I have to disassemble the freezer, remove the inner wall, defrost the coils and clean out the drain hole. Wouldnt smart engineers make an easy way to do that from the back? Seems simple.

Rather than go through all the things I dont like about this washer, just read all the complaints because that is my complaints also: bearings, not enough water in tub, clothes not getting cleaned. Just check out the lint filter and see the gray and dirty lint after a load and you will see it doesnt clean the clothes. Now, the motherboard is kaput! Cycles are all screwed up. Cost is $386 for motherboard plus labor and I will not put one more cent in this piece of crap.Listening to the salesman and consumer reports on the best washer to buy. All they are concerned with is energy savings and believe me when I say that all energy savings products are a joke because you give up operating ability for the sake of energy savings-- true of refrigerators and washers, dryers, furnaces and the like. I will be buying an agitator washing machine. The saving on water are not enough to give up clean clothes.

Purchased what was supposed to be a good dishwasher. In less than 3 years the control panel went out. It would cost more to replace the panel than to buy a new dishwasher. I will never buy another Maytag product.

I bought a Maytag dishwasher (MDB7749SBW1) about 4 years ago. Ive had to replace the wiring on the control panel each year. This is clearly a design defect, and Maytag will not take any responsibility for it. Ive called each year, and am told each time that theyve never received a complaint about this issue. This year Im replacing the dishwasher. Ill never buy a Maytag product again.

We have had this washing machine almost 1 year and the small problems have grown enormous. In addition to the constant soap residue left on the dark clothes (my guess is its on the light clothes too, but you just cant see it) the washer goes out of balance frequently (they are replacing the suspension, after they said its all working great). The repair man said Im not loading the clothes properly, I need to roll each item of clothing into a ball and then place it in the washer. Are you kidding me, my new machine has special needs? And dont put in too large of loads. What!!! Its an XL capacity but I cant do an extra large load, because half the clothes wont get wet or clean. Maytag blew it big time with these models, I could talk about the dryer too. Maybe next time.

We bought a Maytag Dishwasher Model # MDB4709AWW4 about 2 years ago. Complete piece of junk. Just spent $350 on a new control panel. We called Maytag and they told us that our model wasnt under the recall for this issue. The old belief about the Maytag repairman not being busy is a lie. Avoid their products. They are poor quality.

Leaked and leaked, spent hundreds on never ending problems from day one. No support from Maytag. I was told by Sears salesman it was the best you could buy. Our old washer lasted 30 years. This one never worked right - dead at 5 years. Shame on Maytag.

Internet stated refrigerators should last a minimum of 13 yrs and up. Mine is less than 5 yrs. old, a Maytag 25 cu. ft. French Door Bottom Mount Ref. with freezer on the bottom (MFF2558VEW). Had to replace upper gasket in less than 1 yr. of purchase and needs another now (not affecting the sealing aspect on doors, more aesthetic on upper door thin flap that tears easily).Drain plug & configuration for drain was a known manufacturers defect, but cost me money to replace as 3 yr. extended warranty expired. Lower gasket had to be replaced in yr. 4 of ownership, bottom of freezer was producing a sheet of ice that needed removal every week. Normal settings is #3 for both top and bottom, worked fine for 4 yrs at this setting.Last month irregular cooling started to occur- top down to 52 degrees and bottom freezer below -20 degrees - ice cream hard as rock, have to defrost each time in microwave. Maytag repairman said could find nothing wrong, but try emptying entire contents and unplug for 24 hrs. I could hear pieces of ice melting and dropping throughout the evening. Next morning towels I had put around frig were saturated with water. Restarted frig after 24 hrs. and was working fine for 5 wks.This week same exact problem returned so I did the same thing only this time I had to go out and buy a small chest freezer as I had a full one in my Maytag and no place to put frozen food. It is nearing 24 hrs. and no water has appeared on the floor nor did I hear any ice melting and dropping - so dont know what to do. Will call repair man again and see what he suggests. As soon as I can afford another $1400 frig (this was on sale for $1,002 after discounts, but I will buy a less expensive one this time) I will purchase another brand with NO French doors and no bottom freezer. I loved my frig the first 3 yrs. under warranty, but now causing me too much physical problems having to empty and restock frig for repairs. I have a Tappan Frigidaire in the garage that is from 1998 - I bought from a neighbor who was moving and it has been working fine for 16 yrs. with no repairs. They dont make them like they used to!

I think it would be nice to state on the box of dishwasher that customer may need a water connecting fitting and hose for their new dishwasher. Yes, I was asked if I needed anything else and I replied I dont think so! Well when I got home, I did need the water supply sweep 90 degree elbow. Or tell sales people to inform there are parts missing. I had to drive back to Huntsville, AL from Hazel Green. Not life or death, just saying! I do like Maytag products. The dishwasher I replaced was17 years old and we had good service! It’s just starting sounding like a rocket motor. Time to upgrade, I thought. Well my wife really thought so! ;)

I have a Maytag refrigerator that I bought 20 years ago when I moved into my new house. It’s still going strong and haven’t had any problems with it. The only thing that has been replaced is the filter. Knock on wood!!

Bought this Range in March of 2019. I really liked the large oven in it. Right away I noticed that the oven didnt back things very uniformed and very quickly, so a lot of burnt cookies. But I adjusted to that, not super happy about it but it was fine. Tuesday while cooking the cooktop suddenly went out. I had been smelling something strange the last couple of times I had cooked with the oven and cooktop on so I just assumed it was the oven, it did need to be cleaned. Well I ended up pulling the range out from the wall and taking the back metal piece off...the wire running to the cooktop was burned, like 3 inches up the wire and also the wire coming into that wire on the range cord. Just destroyed. I was shaking. My house could have burnt down.I just attempted to call Maytag, knowing my warranty is up (1 year) but thinking they should know about this issue. I was told that they would need to send out a certified tech would need to come out to access the situation...ok...when are they available and she said the 29th of December, really? How many people can go 3 weeks with no oven? I take care of my 93 year old neighbor and make dinner every night. So obviously I cannot wait. I have a tech coming today to fix this fire hazard. I was told there was nothing that can be done as it was not under warranty anyway. What so your certified tech was going to come out for free and then charge me what I probably paid for the range to fix it.

Maytag MVW823OHC SLATE washing machine, $1050 plus warranty $169.95 on 05/27/21 not delivered until 06/25/21, error code on 09/19/21. It is 11/03/21, machine is not working and no part available. Sad.

We bought a washer & dryer from Home Depot 2 1/2 years ago. The control board went out on my washer. I called Maytag and they wanted $109 for a diagnostic fee and wouldnt tell me how much the labor would be. A control board costs $350. So by the time all is said and done... the money would be better spent buying a new one. Maytags slogan of dependability lasts is a bunch of hooey. Washers should last more than 2 1/2 years and Maytag should back up their appliances. They just lost a customer.

Dishwasher Model MDB7749SBM1 - When I returned home from work today, I noticed the cancel drain button was on and the unit was continuing to try and drain but the dishes were not clean and the cascade pod was still inside the unit unused. I then proceeded to run another cycle to clean the dishes and what happened next simply amazed me. I pressed the jet clean button, tough scrub and 2 hour delay button and thought I was all set but the start/resume button would not engage or light up at all and subsequently the cancel/drain button lit up and the unit started draining. Now the control lock and start/resume button just flashes intermittently and wont disengage. I purchased my unit along with several other new Maytag appliances when I renovated my kitchen. I guess the microwave, stove and refrigerator is next -- unit are only 29 months old. Any assistance will be greatly appreciated. Im in deep ish I guess.

Convenience, small, clean while you doing other jobs, it cleans while you sleeping, it's not loud, not expensive, comes in different sizes and colors, it's another helping hand, you will love it, it's worth the money.

Refrigerator - The freezer of the refrigerator would randomly leak on the floor. When I had it repaired on 12/30/14, at a cost of $253.97, the repairman showed me the defective part. He confirmed the online reports that the leaking was caused by a defective part. The defective part had been used because it was cheaper. Now the repaired refrigerator works well. Last month, the control panel on the dishwasher stopped working. According to the online reviews, this is a frequent problem requiring that a new control board be installed. The reported failure typically occurs after the one year warranty expires. My appliances are located in a second home so are only used about once a month. A salesperson at a different appliance store said that appliances usually last from 10 to 12 years. The four years of occasional use prior to failure is not acceptable. I would like to have Maytag repair the dishwasher at their cost. How do I get this to occur?

Please do not buy a Maytag washer top loader. It does not get enough water and it does not clean your clothes. It is the noisiest cheapest made machine out there. If you have kids you really need to bypass this one. I have had this for 10 months and its only me. Please especially if you have children stay away from it. Im the most unhappiest camper Maytag ever had.

Maytag Bravo was making loud noise in the Spin cycle. Ordered new bearing, shaft and parts from Amazon. Also had to order the Bearing tool, cost more than the bearing parts. Total cost $145. Watch a youtube video on replacement, took about 3.5 hrs by myself. Biggest problem I had was lifting the washer up over the drain pan it is in. Washer is on the 2nd floor.

We purchased a MDB8949SAW dishwasher in 2013. 1 month after the warranty expired the touch buttons went on it. If you selected normal it would opt for something else like rinse only. We researched online and my husband followed instruction online to take the door off and seal the moisture to prevent this from happening. This worked for about 2 months and now back to the same thing. We paid $500 for this and just living with the problem for now. All we can do is warn others.

Maytag Bravos XL top load. I purchased 2014. Three years old drum bearings went out, just two people in home. Very expensive to repair. Three years later I hear bearing going out again, in mean time had a F51 pop up and that means major failure call for service. I called Speed Queen and ordered a machine with all metal parts delivered the next day, and it is Made in America. I had purchased Maytag because of name but I will never purchase another Maytag. My friend had the same experience same time frames.

I have had the set of Maytag Bravos for about 5 years now. In the 3rd year, the bearings went out. Just recently, leaking water pump. This washer easily eats clothing. I have to disassemble every so often just to get the missing socks etc. out. The only good thing, Maytag should be ashamed I know this, is that the machine is easy to fix. I imagine since they made it so cheaply. Really nothing to the machine.

Ten years ago I bought a very expensive set of Maytag Neptune Washer MAH5500BWW and dryer units with the single all-in-one pedestal. The washer starts sounding like a freight train during the fast spin dry cycle. A service tech came out, turned it on, listened, told me it is bad outer tub bearings going bad. And the price to fix is $846. Its essentially a throw-it-away deal. The tech says he has done hundreds of these and its a 3-hour major tear down, the bearings are press fitted and you essentially buy a new outer tub instead of replacing the bearings in the old one. Maytag went out of business and was bought by Whirlpool. What a piece of crap and to think how great Maytag once was. Now I have a dryer and a pedestal that probably wont fit any other washer brand.

Thanks for the other reviews about the control panel problems... I too have the same issue with the short circuit. My Maytag dishwasher mdb7749sam1 was installed in January 2013. I spent an hour on the phone and the chat... HERES THE SOLUTION: When I told them the machine started in the middle of the night on its own, it became a safety issue. I have all the same problems as everyone else, flashing lights, the washer does not properly respond to the input from the control panel... I was told that even though it was out of warranty, as a gesture of goodwill Maytag is sending out an authorized repair service to fix whatever is wrong at no cost to me at all... Tells me that there really is an underlying issue. Anyway best of luck to anyone else in the same boat. I rated them as a 3 - not happy that this machine failed and I wont buy another, but they seemed to jump on fixing it...

When our ice maker (Model # MF12269VEM10) stopped working, we contacted Maytag, only to be told that the 1-year warranty had expired. So we had no recourse but to contract a repairman. He replaced the valve (and in the process, because of Maytags decision to use plastic tabs instead of screws, the tabs for the filter housing broke off in his attempt to reach the rear of refrigerator where the valve went and we had to pay to have the housing replaced, also). The new valve did NOT fix the problem. Water continued to run out of the water dispenser after you removed your glass. We re-contacted the repairman who returned and proclaimed that there was air in the lines and it should work itself out over the next several days. Yet that night, I noticed drops of water running down the control center and filling the drip tray. I placed a towel on the floor and emptied the drip tray several times that night, before turning off the ice maker completely the next day.Unhappy with the original repairman, we contacted another who came out and discovered that the new valve was leaking from the top. That is when the filter housing broke and we had to use duct tape to hold it in place while the new repairman ordered a replacement. He tightened the valve and cycled the ice maker several times only to discover that the water overflow switch on the ice maker wasnt working, thus water was overflowing into the ice maker container. He turned down the water pressure to the refrigerator, and we tested it again. All seemed to be well until the next day when no ice was released from the ice dispenser. When I removed the ice storage bin, I found everything frozen from water overflow. I turned off the ice maker entirely and contacted the repairman, who ordered a new ice maker, which took about a week.After the new ice maker was installed, along with the new filter housing, the repairman cycled the unit several times before leaving. Yet by the next day, the ice in the storage bin was frozen in place again (I have pictures), and we contacted the repairman who ordered yet another ice maker. It took yet another week for the part to come in. After it was replaced, I monitored the ice container each time I heard ice drop into it. The 1st time there were a few drops of water in the bottom of the ice maker. The 2nd time, there was a 1/4 cup of water in the bottom. I immediately contacted the repairman to let him know and turned off the ice maker yet again.I find it hard to believe that a new valve, fresh from the package, and 2 (TWO) ice makers, fresh from the box, were all faulty. The repairs started on February 25th 2015. It is now March 21st and the ice maker is still not repaired. The 2nd repairman is doing his own research into the problem (for which we applaud him!) and now we ask you for your feedback as to the problem and how it can be solved.

I bought a Maytag washer from Lowes and bought the extended warranty. The warranty expired but Maytag is not taking responsibility for the lemons that they sell. I have seen many reviews stating that the bearings went on the washer. This is what happened to me and it happened twice already. I spent 798.00 on this washer thinking it would last for more than 6 yrs. They offered me a warranty for 368.00 or to purchase another washer at a discount price. Of course I refused but I want everyone to be aware of Maytag Washers - not worth the money.

Our Maytag microwave MMV4205FZ-0 has the same ubiquitous problem as so many reviewers have mentioned. The microwave refuses to turn on (always at the most inopportune moments--like when the entire family is over for dinner. It doesnt matter how many times you open and close the door, it will often refuse to start. I think the worst part about this situation is that there are so many reviewers experiencing the exact same problem. Imagine how many havent posted a review. Doesnt it seem as though a rethinking of the door switch would have been in order long ago along with a recall? The fact that hasnt happened after so long and so many customers who are disappointed in their purchase is a sad commentary.

Washing machine required service approx 3 months after purchase. Dryer heating element stopped working just after the year warranty ended. To fix dryer will cost approximately 30% of the purchase price of the machine. And all the while I am tainted by the 10 Year Warranty sticker that I never removed from the machines. Never again will I purchase a Maytag product.

Our washer ran great until last week. Had repairman in. User interface died after 18 months use. $250 for the part plus labor. This is a $1000 washer. Buyer beware. Maytag is just another name for any washer in the Whirlpool lineup. Uses the same parts. Has the same issues. Should have bought a Speed Queen.

18 month old range did not shut off although it showed off on the cancel page. $800 down the toilet. Maytag had the guts to charge $100 to troubleshoot plus parts and labor. I will donate it to scrap metal. Company does not give a rats behind. DO NOT BUY MAYTAG.

Was coerced into purchasing this fridge three years ago. Told how Maytag is the highest quality fridge etc. From day one it was noisy and seemed to be running half the time. I had asked for a quieter fridge, partially why I paid $2000 for it. Now there is something wrong with it. Not sure what yet. But for $2000 it should not be failing three years later. My Samsung was quieter, 1/3 of the price and lasted at least 8 years. Thought about calling customer service but read too many bad experiences here in regard to that. Will never use Maytag again.

This is a review of a washer that is no longer sold. I bought a top of the line Maytag washer 45 years ago. After around 25 years the control (all mechanical) started sticking during the cycle. I opened it up, sprayed it with TV Tuner cleaner, worked it a few times, and it has worked perfectly ever since. That is the only problem or repair on that machine since it was purchased!

We purchased our Maytag Bravo XL in 2012. Over the past year and a half we noticed the inside of the top lid is rusting as well as the bleach dispenser area. I called Maytag about the lid and they said there was nothing they can do and that we could buy a new lid replacement. Really??? My parents had only Maytag in their home for over 50 years with little to no repairs needed ever! We were a family of five back then. Because my parents always bought Maytag products so did we. This is the first time in 40 years that I have ever seen this happen! I was hoping for a recall for these issues but dont find any online. The washer and dryer were not cheap and purchased from a reputable retailer.

After only three years of gentle use, my Maytag front loading washer bearing went. The repairman said this was because of too much detergent and the repair bill would be over $1100.00 (more than the cost of a new machine). I would never buy this machine again.

We purchased a Maytag convection oven less than a year ago! Today is the 3rd time the heat sensor has gone on it! I want a new stove! I am beyond disappointed with the business and the product! Have always bought Maytag! Rethinking it now!!!

Purchased Maytag washer Centennial Econoserve washer. It was 2 years old Aug 2013. Washer stopped working Sept 16, 2013. Of course since it had Maytag name brand, I did not purchase extended warranty due to thinking it would at least last more than several years. I called Maytag/Whirlpool. They gave me name of authorized repair in our area. So far they have come out 2 times. $560.00 later, it is still not working and they have no answer as to how or what to do. We are now into $1300.00 between purchase and repairs and still no washer. We are retired hard working people and this is really a bad way to treat consumers. Maytag customer service could care less about the situation. They just say we should have purchased extended warranty.

Approx four months ago we got new stainless steel Maytag fridge, stove and dishwasher. Terrible, terrible, terrible. The dishwasher rack was broken, and the parts are plastic and hardly any room on the racks. The fridge had the wrong hinges and doors on them. We have been waiting for four months to have them replaced. Today we checked with Maytag and still not coming. The fridge makes a very loud humming noise it almost shakes the floor. This was some sort of compressor problem. Now the fridge is having problems with the freezer. It is freezing up with frost everywhere. The stove is terrible. I waited an extra month to get a convection oven which I have had before and this one is terrible. The double oven is a great feature if they work. They take forever to heat and if you do anything with the food you have reset the temperature? The top is the worst for cooking as the only one that works fast is the boost but then it slows down and you have a hard time cooking the food. The black top is very very hard to clean. I have owned a Maytag washer and dryer for the last 34 years. They have been excellent. Since Whirlpool took over Maytag they seem to have run the name into the ground and all the good service and products they had built up are now ruined. I told my neighbor a few years ago to buy a Maytag washer and dryer and they did. They have had nothing but trouble and are now having to buy new ones but not Maytag. It is a shame that with all the technology that Maytag has built up over the years is now gone. If you look at all the terrible reviews I dont think Whirlpool will be in business much longer with products and service like this. I still have a fifties fridge for pop and beer and it is the best fridge ever with no problems and my last fridge in my garage, that I replaced with this Maytag is still better than this new fridge. The service man that came to fix the fridge said we had to build in the fridge to keep the noise down. How come they never had problems with Maytag products years ago. I feel its all about the almighty dollar. They only last a few years and you have to buy expensive warranty. If you made them properly you would not need warranty and they would last for years like before. If anyone knows if there is a class action suit against these companies let me know since all of us should not be ripped off and costing us time and money.

Run away from this piece of junk machine AND company as fast as you can! I bought this set Oct 12 and by March 14 it was grinding/whining during the agitation cycle. I have been in contact through various forms with Maytag and they do not care! They first contacted me to review them and when I reviewed them very unfavorably they emailed me and this is what they said: Our staff has read your review and values your contribution even though it did not meet all our website guidelines. Thanks for sharing, and we hope to publish next time! All I did was say exactly what happened.After that I went to their website to see what kind of reviews they were getting and lo and behold their rating is 4.4 out of 5. Of course it is when you simply cherry pick the best and plant a few lesser rated ones. I simply do not have the funds to replace what I thought was a quality product, nor am I sure I want to repair it as it doesnt clean clothes. I hate having been placed in this predicament by a greedy, slimy corporation whose only interest in me is profits.

Maytag dishwasher quit working 3 years old. No power. Control panel dead. Piece of junk product.

Bravos washer is 4 years old. Started making an extreme amount of noise during the spin cycle. Had a repairman look at and showed me the bearings and area under the tub. $400 plus in damage due to bad bearings, rust to bottom of tub and surrounding area. Four years for a high-end washer is pretty bad. Needless to say, I will buy a new unit and would NEVER recommend a Maytag Bravos appliance.

The Bravos XL MCT Maytag commercial Technology is not a good machine. I noticed it within the first few weeks. I called Conns to request technical support but the technician they sent didnt solve the problem. I also called Maytag, they also sent a technician. He told me the same thing as the other guy. To use good quality detergent and to make sure the clothes are neatly arrange around the drums walls. Nothing works. My clothes dont get clean because they dont get wet. Theres lots of residuals and wrinkles all over them. Also, the machine takes way too long to finish a load of clothes. I did tried to return it, but Conns wouldnt take it back. I dont recommend this washing machine at all!

I have always thought of Maytag being the quality manufacturer of appliance products. We purchased a Maytag microwave (MMV4205DH-1) and after just two years it has begun to give us grief (we are in our early 70s, no family at home, so appliance receives medium usage). We constantly get the open/door message when we are trying to set the timer for operation. We open and close, open and close, etc. Just yesterday my wife noticed a slight crack on the door just below the handle, most likely due to frequent open and closing. Went online and read a number of reviews and found many others have had same or similar issues. Done with Maytag.

We bought our Maytag washer and dryer a bit over 5 years ago. Now the UL warning comes on. Found out it will be over $400 to fix it. It only cost $500 new. Repairman says it is very common and not to pay him to fix it. Our GE went 20 years. Lesson learned, wife is out looking at new GE.

I have a 50/50 chance of completing a wash cycle. Most times, the washer stops working at 8 minutes remaining in ANY cycle. The washer will leave me with wet clothing and refuses to spin even when most wet, dripping articles are removed. I have tried to put all light-weight items together and that still is not a guarantee that I can get this done in one cycle. Most often, the error code comes up, I spin the drum around, move the clothing around and try again. This process is NOT energy efficient which is why I bought the ** thing in the first place. I am ready to put it on the curb for the trash man to pick up.We had a service person out and he said it is either the bearings or the motor (both a $400 job). I will NEVER buy another front-loading washing machine. At least with the old-fashioned top loaders you can get the load balanced and at least get clothing to go through the spin cycle. I am now hand-wringing clothing once again since the machine tells me when it will spin my clothing. That stupid chime is about to send me out of my mind!

I have never reviewed anything and feel compelled to chime in. The Maytag Bravos XL is the WORST washer dryer set ever. My 20 year old tiny washer with agitator cleaned a million times better in half the time. In fact this washer doesnt even clean your clothes! The reason is because so little water comes in and you cannot manually control the amount of water. Ive tried deep water wash-total joke. Heavy duty wash and extra rinse, still no better. You can wash it 2-3 times with the same poor results. Who wants to put on dirty underwear! The dryer easily takes 2 cycles to get an average size load dry and forget sheets and towels! They take 2 hours.

Washing Machine MVWC6ESWW - The fourth time was October 12; I called. Shreka at Maytag said she would send someone out at no cost on October 15, between 12-5 pm. Justin called from AE at 5:05 pm stating he was on his way. He then asked for my receipts. We were moving and had packed many things. He said he would call and find out. He said they were out 7/2011, 9/2011 and again 9/2011 all for the same problem. I requested in September 2011 that this was a lemon and send me another. I was assured if the same problem occurs, it would be covered. Well Justin said it isnt covered anymore and it was due to being made overseas. The cost to fix it is around $350 to $400. The washer cost me $383.40, plus I bought the matching dryer of $403.39. This makes zero since. Please advise.

I have a fairly new washer Maytag model #MHWE500VW serial #CSY0303991. I need Part # W10415587 doesnt excist for my washing machine anymore. Its been on backorder since Apr-May 2011. Maytag/GE insists that they are not responsible. As long as they can say backorder technically they are not liable for anything and dont really care that me the customer is having a problem and they Blatantly refuse to even investigate. I spoke with a GE supervisor just today and she basically told me wont help you because my appliance is out of warrenty. And she explained to my that my complaint will go into a file that no one will ever see. I searched the internet only to find hundred of other consumers are waiting for this same part. Ive called distributors & manufactuers. Same answer, backorder. My warrenty people are trying very hard to help me but again Maytag/GE refuse to help. Very dissappointed with this company. Wont be purchasing Maytag/GE products again. Wheres that guy in the commercial with nothing to do when you need him??

Maytag washing machine exploded sending glass shrapnel everywhere. At this point I believe Maytag should replace the machine. I appreciate after MANY hours on hold and being transferred that you are sending a repair person out, but there is tiny glass shrapnel all over inside. This is crazy, and a MAJOR safety concern.??? Update - can’t find parts or an eta. Replace the machine!

My Maytag dishwasher which is less than 2 yrs old had its control panel and board gone bad. It took almost $400 to fix it. It seems like an ongoing problem and Maytag does not do anything. I would have bought a new dishwasher for that price, but I was already in for almost $200.00. They dont give you prices upfront.

My over-stove microwave is approximately 18 months old. Suddenly, the fan came on and will not turn off. I had to unplug the microwave. This appliance is out of warranty but certainly should last longer than 18 months. I feel that Maytag should certainly be called to task for selling and promoting such a shoddy, unreliable product.

The Maytag Centennial is the worst washer ever. Not only doesnt get the clothes clean but it does not spin out properly either so your clothes have to be run through a 2nd time after washing. The water fill level is so low that the clothes are not covered in water at all, even midway through the wash.

We had remodeled our kitchen in 2009. Bought new fridge and stove (Maytag). The oven door came off and cant get it back on. No matter how many times we tried, no way can we get it back on. I had to have my son to come and help us. No sooner did we use the handle to open the door off again. This has been going on for 3 years. **, well fed up. I called Maytag about this issue and they told me they would get a repair at my cost. The fridge freezes all the produce, cant regulate the temperature. Never ever will we buy any Maytag product again. Who knows what’s going to happen next? Oh, and the paint is chipping off of the grates of the gas stove.

Purchased dishwasher Mod # MDB7749SBM1 thinking it was Maytag (lonely repairman) in June 2013 from Home Depot. Cost new over $1,000. As of March 2016, three service calls, two of which required replacement of the control panel. Now the control panel has failed a third time and we are told by Whirlpool (parent company of Maytag dishwashers) they will not cover the repair. They have offered a discount for a new dishwasher. Since that did not seem like a very good option to me, they offered to let me pay for current service plus a year for over $350.00. I was sad to discover that they are the manufacturer of most dishwashers available at your local home store dealer (Whirlpool, Maytag, KitchenAid, Jenn-Air, Roper, Amana). VERY DISSATISFIED CUSTOMER!!!

We were replacing a 4 year old Whirlpool Duet washer (bought on recommendation from sister-in-law) that needed the third repair and was putting holes in our clothes. We had purchased the warranty (which we had never done before) so Lowes gave us the choice of machines and we decided to go with the Maytag Bravos. Lo and behold, were still getting holes in clothes. Several repairman told us the issue is common and is caused by the force of the water flowing into the machines plus the rapid spin cycle which pushes the clothes through the punched holes in the tub and the clothes catch on the metal on opposite side of the tub. Turns out sister-in-law had the same problem with her Duet and (not knowing I bought the Bravos and had the same issues) bought the Bravos and also is still getting holes. So I know its not just me.We also have problem with the machine not putting in enough water so clothes do not come out clean. In fact, a lot of stuff comes out with areas that havent even gotten wet during the wash cycle. I just want an old fashioned machine with an agitator that fills the machine fully, washes my clothes and doesnt put holes in them.

We bought MDB7759AWB Maytag dishwasher in 2011. It worked decently until now when it stopped delivering water to the upper rack. The cleaning quality on the lower rack also dropped significantly although it might be due to the lack of water delivery to the upper rack. Apparently there is something wrong with the internal pump. The Maytag service offered a repair for $300+ which I rejected because this is a ridiculous cost and I would rather buy a different dishwasher. My conclusion is that if you buy Maytag dishwasher you need to factor about $300+ for the repair(s) in 5 years as apparently they do when they sell you this product. Anyway, even though Maytag was a decent brand a long time ago (probably in the past century), it is not reliable anymore. It does not mean it has to be much worse than many others but if you are looking for something better than those others I would not recommend Maytag.

Do not buy this refrigerator!! It’s small on the inside but to top it off the vent is on the left side, not in the back, so everything freezes on the left side of the refrigerator. Plus they positioned the light right in the front at the top so you cannot put a gallon of milk or anything tall. Not orange juice, apple juice, nothing!! Horrible design. I’ve had the repairman out, he said he couldn’t do anything about the freezing on the left side unless he turned the temperature up on the fridge and on the freezer. We tried that & The ice cream was so soft, almost melted. The problem then was the temperature was too warm for milk and other items. Not a recommended temperature to keep cold items. He said I would have to keep everything away from the back & the left side to use it without freezing my items. I’ve lost a lot of food because of this. Very unhappy with this refrigerator!!

I am submitting this review today to express my disappointment with my Maytag washer. This is the Maytag MVWX655DW (Bravo), with Serial# C61842055. In August of 2016 I lost many treasured items due to a flood in Lafayette, Louisiana. My daughter and I were devastated and displaced because of this event. This is also in addition to completing Cancer treatment 2 days before the flood.I lost my GE washer which was a great product. It was a struggle for a long time, but we were finally get back on our feet. I was able to get another place to live, and it was time to purchase a washer. I was told that Maytag was one of the best products on the market, so I decided to purchase my first Maytag washer. This did not turn out well for me, and it was very disappointing. After 9 months of ownership of this product, it is broken! It is my belief that the product may have been defective.I put in a service call, and had a repairman come to my apartment on June 19th. I was told that my washer needs several parts to repair it, including a pump. I have never had this issue with prior washers. My previous washer before my GE purchase survived for over 10 years before it has had any issues. I called on June 26th to ask about Maytag issuing me a new washer or a full refund, instead of repairing this faulty product. I was told no, and was offered and extended warranty for 6 more months and $75.00. I expressed to her that I would rather have a new washer.The Bravo Washer is a very bad product. Instead of taking advantage of customers, Maytag needs to stand by that 10 year warranty sticker on the washer. Please understand this purchase is a LEMON. This washer did not last a year. After all I have been through, I did not need this financial hardship. In the long run, this product will die again. Unfortunately for me I may not be able to afford to purchase another washer. I am still getting follow-up treatment for my Cancer, and it is very expensive. Can someone please re-evaluate the need for a replacement washer or offer me a full refund? This product should not be broken after only 9 months of service.

In 2011 we purchased a complete appliance grouping at Home Depot by Maytag to include the dishwasher. For some reason we neglected to purchase an extended warranty on the dishwasher. Lo and behold in 2013 our control panel went bad and the cost to repair it was almost as much as purchasing a new dishwasher. Thinking this was a fluke we were dumb enough to purchase another Maytag from Home Depot due to the loyalty made in the USA. Well here we are 2015 not even a full two years later the control panel started acting funny a few days ago and yesterday just plain old QUIT. Fortunately we were wise enough to purchase an extended warranty plan on this dishwasher so tomorrow we will be calling the repairman. Unfortunately Maytag has never solved the problem that has been occurring for at least 5 years and continues to sell this product to unsuspecting schmucks like us who try to be true to the made in the USA slogan. Shame on Maytag!!! Our model number is MDB7749SBM. Buyers beware.

My Maytag refrigerator Model MFX2571XEMS has to constantly be defrosted due to ice accumulation in the bottom of the freezer. If not defrosted, water leaks out onto our hardwood floor. Maytag will not do anything to resolve this problem. We were told by a repairman that we have to defrost it manually to fix the problem. Yeah at least every 2 weeks. What a rip off.

Weve only had the machines for about a year, but so far they operate perfectly. However, the washing machine seems to take much longer to operate than my prior machine and is much noisier. But, the cleanliness of our clothes is great!

Maytag Dishwasher, mdb7749sam1 - I got this dishwasher new in Feb. 2013 for my new house. I thought that Maytag was supposed to be a very good appliance company. (I just found out that Whirlpool bought them! I dont like their dishwashers, either! Ive had 3 whirlpools that only lasted about 2-4 years each.) My dishwasher worked great until the control panel buttons started blinking and going crazy! Then, it just stopped working altogether. I called Maytag about this part, and found out that it is only covered the first year, and the so-called 10-year warranty doesnt cover it. What good is the extended 10-year warranty if it doesnt cover all the parts!? I researched this dishwasher before I bought it. It got fairly good reviews at the time. Now when I look it up, it gets these terrible reviews! I am so disappointed with this situation. I have other Maytag appliances that have performed great. Im not sure why their dishwashers cant be made the same way.I am going to order the part and repair the machine. I hope this will fix the problem. I had hoped that the Maytag brand would live up to their hype, and be better than the Whirlpools I had already had such bad experiences with. The Whirlpools had great features, they just didnt last! This dishwasher, too, has great features. Two years isnt a long enough run for it to be a good choice, though. Really disappointed :(

I bought a new Maytag stove and it is less than two years old and the oven has already quit working. It only has a one year warranty and will cost about $200 to fix. I am very dissatisfied with what I thought was a good product.

We bought the Bravo XL set 11 months ago and the washer leaks all over the place.. Called Maytag and had the repairman show up. Upon arrival he told us these were the worst machines to buy and would never recommend to anyone. He also said that business has been great due to all of this.. He checked the washer and said the water pressure was too high and lowered it. He couldnt find anything wrong with it. After he left I started a load and sure enough it was the same. Called him right back and he said to call Maytag because he was going to another repair job. I called Maytag again and they said to call the repair guy.. Never again will we ever buy Maytag.

I purchased a Maytag range (YMER8875WS) on June 20, 2011. When I put my Christmas turkey in the oven, the rack fell! It seems the oven wall has gotten wider in the middle, so the rack doesnt stay in place. I have read several comments online about this, particularly relating to Kenmore ranges. This is a very common problem apparently caused by the oven liner bowing outwards.

We bought this refrigerator in 1998 and it is still going strong. It has gotten a bit noisy over the years when defrosting, but it works great. It is not as fancy as the freezer over top, but it is large and so is the refrigerator.

My Maytag Series 300 Dishwasher would not start. I read the reviews and took the door off (easy if you have the right tool), removed the control panel box (one screw), and cleaned the ribbon with electronic cleaner as per someones suggestion. It started right up. This is a bad design. Would I buy another Maytag? - No way! We will see how long this lasts. There is no seal on the door to keep out humidity. Do we really need a new control panel? When this is done...I am done with Maytag!

I have a Maytag dishwasher MDBH980AWQ10, within the 1st month of owning it there were issues. Now the electronic control panel is shot, dishwasher wont turn on. To replace it...almost the cost of what I paid, warranty has run out. In the last 7 years we have had problems with 5 various Maytag products, replaced our Maytag dishwasher which lasted 20 yrs and Maytag washer & dryer that lasted 30+ years and ran without a hitch. Maytag has not been helpful at all and their authorized service repair. A&E Repair Service is a bigger scam than they are. It is a waste of my finances and time to buy major appliances every 5 years. Each and every one of their new appliances has died shortly after all the warranties have run out. Im beyond frustrated, disgusted, and financially drained. It does not pay to be brand loyal to Maytag for they are no longer respectful nor appreciative of their customers. I would love to give corporate the opportunity to enjoy the same products that are in my home...in their homes...as well as the experience of their customer service. Last Maytag purchase for me! Is there anything that I can do in the meantime so Im not stuck with their lemons?

I have to say I am terribly disappointed in the quality of my Maytag Side by Side Fridge/freezer and my Maytag stove. Having sold Maytag commercial washers and dryers to coin laundries for over 20 years I expected better. Needless to say..... these are Whirlpool machines with Maytag name plates. Not the Maytag quality that was produced in Newton, Iowa. You can tell these are plastic machines made in Mexico. Of course you still pay for the Maytag name just not the quality. I have always tried to buy from US companies, but my next appliances will not be as Whirlpool is the only US company left with exception to very high end products.

Maytag Bravos Model MVWB750wq1 - After only two years, the washing machine finally died. The machine was on a f51 code - hardly anything was in the washer. I also smelled a burning smell - well, that was the pump. The machine was not pumping water out. After the repairman came out, the contract company is saying they are not covering this because there was rust reported by the repairman. How can bearings inside a washing machine be rusted? This is a washing machine, isnt it? How are they building machines that deal with water and rust?! I will never buy another Maytag product - thats a promise. I spent over 2000.00 on this set. Never again.

Maytag Frenchdoor MFX2570AEM3 - Was initially really excited with this brand new fridge. We have not even fully paid it off, as we bought with credit at Home Depot, and it continuously leaks water from freezer! I have taken everything out, defrosted, spent about two hours pushing hot water through the freezer drain with a turkey baster and it was only about four days before I had a puddle on my floor again! We have bought quite a few maytag products before, but after this fridge, probably never again! If there is a recall or a lawsuit pending, please, someone advise me of either.

When I remolded my kitchen almost four years ago, I purchased four Maytag appliances. There was a recall on my dishwasher that was successfully fixed; the heating coil could have caused a fire. The next appliance to go was my refrigerator with a bottom freezer: the freezer section went. Thank goodness I purchased a policy which covered the repair that had to be done twice--twice I lost food. I was compensated by the insurance company for $200.00 for the cost of food lost. Just before Christmas my microwave stopped heating. The turntable works, the timer works, but it will not heat the food and makes a loud noise. The glass top on my stove is getting marred even though I clean it every time something spills. I keep my appliances in immaculate condition and they look like new. I thought when I purchased Maytag I was buying reliable appliances. Their ad that states that the Maytag repairman is lonesome because he has no work is a lot of bull. Each appliance has had problems. Where is consumer protection? Appliances should not breakdown after a couple of years. We should not have to buy insurance policies that are expensive to protect appliances that should last at least ten years without problems. Someone needs to step in and help the consumer. I didnt call Maytag regarding the microwave as I was told it was useless to call them and all I would get would be aggravation. Someone, please help the consumer!

I bought the Centennial top load washer and the dryer in May 2016 at Lowes. They are junk. I had a secondhand Craigslist Maytag washer that lasted 7 yrs and it was still running just fine when I got rid of it after purchasing this HE junk. The flimsy plastic door handle on the dryer fell off about 6 months ago. The clerk at Lowes assured me that the washer was high capacity & could handle heavy loads. Now I cant wash heavy loads because the agitator is already loose and getting ready to break. I have to wash smaller loads on the hand wash cycle. I cant wash my comforter or my rugs. The real kicker is I cant reach Maytag! I have tried calling to sit on hold for 30 mins to an hour. I tried the live chat during their regular business hours and it was not open. I am so disappointed in these machines. This is the first time I have ever purchased a new washer and dryer and this is what I get. I might as well have set $850 on fire. DO NOT BUY NEW MAYTAG MACHINES. THEY ARE JUNK.

I purchased a Maytag gas range after remodeling my kitchen. I thought I was getting a good product, boy was I wrong. The ceramic gas grates are so slippery that pots tend to slide off but the real problem is that the racks inside the oven fall when you place pots on them. I tried cooking a Thanksgiving turkey in it and the racks fell to the bottom of the oven. It appears that the top rack and the bottom rack are the only two that stay in place. And it also appears that when the oven is on, the sides of the oven expand so that the racks fall. I have tried to contact Sears as thats where it was purchased to no avail. I will now attempt to contact Maytag directly but it appears that I will also not get anywhere there. I have read at least one other complaint of this exact same type happening to someone else. This is very dangerous. Do they really want a lawsuit?

I purchased the Maytag dishwasher a little over two years ago (MDB6759AWQ0). This was the first Maytag product I bought and it is definitely the last one! It was more expensive, but because of Maytags commercials on what good products they had, I thought it would last longer and work better. Boy, was I wrong. When it was installed, it was loud. I brought this to the attention of Maytag. I was told there was nothing that they could do. Repair people were sent to my home several times to see if the noise could be fixed and unfortunately, it could not. This is the loudest dishwasher that I have ever had. I should have stayed with the same brand that was over 10 years old that died! Now the control panel blew out and will cost over $300 to have it fixed. After reviewing the numerous complaints that you have on your dishwasher with the control panels not working, I would think Maytag would be more financially responsible in helping the people that have your products that no longer work after being less than three years old. Just a heads up, Maytag, I will be replacing instead of fixing and not with another Maytag product!

I have a Maytag Neptune washing machine which had a mold problem on the rubber grommet. I have been trying to call Maytag to no avail. I researched and saw there was a class action suit for this very problem and I was never informed. The washer may pose a health hazard and I would like Maytag to do something about it.

I also have a Maytag Quiet Series 300 dishwasher. The front panel has stopped working. It was a horrible dishwasher from the beginning. The dishes were streaky on the top rack. And I had to replace the rollers after just over a year. The upper rack has rust on it. The Maytag double ovens I bought at the same time had to be replaced within a year, as the racks damaged the porcelain interior. I also wish I had found your site before my purchases. My husband is not working now. So, I guess we will be washing dishes the old fashioned way.

Maytag MVWB835DW was less than 2 years old (purchased 1-14-16) when it began to fail. Maytag sent repairman out, he declared it beyond repair. Machine locks, washes and adds more and more minutes and cant turn it off without unplugging 5-10+ times... sometime takes a week to get clothes out of machine because of locking itself. I have extended warranty and yet when I try to contact Maytag, to have them honor this, there is eternal wait on phone, online, no help whatsoever. I read via Consumer Affairs that there are almost 3,000 reviews on this specific machine being a problem yet amazingly the Maytag man never responds! I have spent many many hours with no resolution. Amazon says so many reviews have been written about this, that they are unable to take my review because of excessive reviewing.

Bought a Maytag washer from Lowes 3 years ago and it is just junk. I am 62 years old and never had a washer that actually broke down. What happened to good American technologies. I guess those days are gone, anyway dont buy a Maytag, duh. It is the day after x-mas and I have to buy another machine.

We purchased a Maytag Bravos set in 2011. The dryer works great, but the washer not so much. Every load of darks comes out with soap scum all over. I use the HE detergent and most time use less than what the load should have. We have soft water and I also use softener. Ive also tried up to 3 extra rinse cycles and a smaller load size and still have soap scum all over. Im sure the light colored loads come out same, just cant see it. Needless to say, very, very upset with this washer. I, too, will never buy another Maytag product, nor will I recommend one. Had our yearly maintenance check the other day and the service man couldnt give me the reason its doing this. So, so disappointed in this product!!

I inherited this Maytag washer, so it has been around a very long time (I have had it for 18 years). It still runs quite well, has 3 levels of wash/rinse, 3 cycles to wash in. Both of us...me and the washer are still kickin together. Highly recommend Maytag.

We purchased a Maytag dishwasher from Home Depot in January 2009. We did not begin using it until perhaps March of 2009, so just over 2 years ago. It gets ran maybe 1 to 2 times per week. I went to turn it on a day ago and the right side of the control panel, where you press the start button, does not work. When I checked Maytags website, I discovered there was a recall due to the heating element. So, I had the repair technician out and he told me that the control panel was bad and it would cost $300 for parts and labor to repair. We paid $600 for this dishwasher. Of course, we have the option of purchasing a new dishwasher and receive a rebate but that ends up being more than just ordering parts and replacing them ourselves, but something only 2 years old should not break. From reading all the other complaints on this forum, I am surprised that Maytag has not done something about the control panel and the humidity issue which seems to cause the control panel to go out. This is an expensive fix which Maytag needs to address. Come on Maytag!

I purchased a Maytag refrigerator from Home Depot 2 years ago and the first year I already had problems. The second year there was ice on the bottom freezer I called Maytag. They claim a technician needs to come out but cant tell me how much it is to come out for an estimate. After they come out they tell me how much it was. Everyday I have ice or water from the freezer. I had also purchased my stove which very easily has been all scratched and considering that I hardly ever cook, I figured it would look new for years. I will never buy another Maytag appliance!!!

Bought the Maytag MDSH969AWS1 in Dec. 2010, and it quit after 4 and 1/2 years. Ironically, replaced a perfectly good 20 year old GE model that ran great for this piece of junk. I tried to diagnose the problem: the washer fills, but when the cycle is supposed to start it just hums. Then you have to drain it. So I think the problem is the motor or capacitor. The parts are stupidly overpriced, and Im not even sure if that is the problem. It could also be the electronics board (Ive heard of the problems with these on this brand). So instead of risking wasted time and parts Im junking this, er, piece of junk. The stainless steel door was rusting on the bottom too. American made crap! Bought a fancy Samsung to replace it, and will NEVER buy Maytag again. Im old enough to recall the lonely Maytag repairman -- Itd give him a swift kick in the rear for being associated with such a shoddy brand. Maytag, its the Dodge-Jeep of appliances.

Bad decision, Purchased in 2013 a Bravos by Maytag. After 3 years, it sounds like a jet engine taking off. The bearing is failing, sad as Maytag advertises to be the best. In 35 years, this is our 4th washer, actually the 1st was a hand-me-down that lasted longer. Unfortunately, we thought spending more and believing that Maytag would last longer was a mistake. Cost to repair is over half of the cost, so we have elected to run to fail. Then replace the Maytag that should have lasted at least 10 years. Warning. Purchase at your own risk. DO NOT buy this machine or any by Maytag, could be the same results. Or it could be that they are manufactured under Lowes specifications. From all the complaints the Maytag repair technicians are working, not setting around as they advertise. Only blaming myself for the purchase.

I purchased a Maytag Bravo xl washer & dryer for $1600 in May 2017. Sunday, the user interface panel went out in the washer. After an $85 diagnostic visit, we were told it would be $500 to repair and take an additional 5 days. My husband is recovering from major knee surgery so I was short on choices. I elected to purchase a new speed queen and will never purchase Maytag again. The 10 yr warranty tag on the front is useless!

Maytag dishwasher mdb7749awm2 - It appears that everybody who bought one of these dishwashers has run into this issue at one time or another, and it usually takes one full year of use before the control panel goes out on these units, and in most cases, it has to do with moisture getting on the thin strip of wires leading from the control board to the control panel. It usually occurs right where the strip enters the control panel... There is nice little gap for moisture to rest right on the wires, which will eventually lead to corrosion. I included an image of what to look for (see the nice black rust areas on the wires? That was my problem, and probably yours, too). If you have some very, very fine sandpaper, and have patience, then you can get the rust off the wire, but be very, very careful, or you could take the small thin wire off in the process! Ive made this repair myself to my unit, and I did it for one my friends machines (it was a Maytag, and his lasted two years, but had the same problem, too), and both had similar problems and right in the same spot! After removing the corrosion, the system worked great again. However, before hooking the unit up again, I sealed the area with some silicone to hopefully prevent this from happening again. Now, Im not saying that this is the problem that you are having, but its worth investigating, and dont be afraid to pull-off the front panel...its just held on with an adhesive and will go back on with no issues. Anyway, this could save one hundreds of dollars in repair costs. I hope that this helps.

Maytag Dishwasher MDB7749SBW3 - Control panel problem just like everyone else describes. Bought in Nov 2014... how disappointing!! My husband is sure he can fix it if I buy the part. I went online to order the control panel, and of course because Im in Canada I cant ship the part directly from the website, I have to call the Canadian Sears Part Dept., its about $200! As I came across all these reviews I am even contemplating if I should waste our time and money trying to fix this thing... Maytag never again!!!

All I can say is what a mistake. Had a front loader that always smelled and had mold around rubber gasket in door. So, wanted a top loader this time after old GE died. Unbelievable, not enough water to clean clothing. Clothing comes out with some dry spots. And the worse thing is washing black items, tiny particles on black pants, shirts, etc. Think is lint not soap but not sure. You have to rub all over the clothing to try and remove. This washer is 8 months old and I have cleaned it with baking soda and vinegar mixture thinking this would help, it doesnt. The spin cycle sounds like a rocket ship taking off. Lots of banging noises during operation also. I have invested a lot of money thinking Maytag is rated high. It is a pretty grey color with glass top. Well I was fooled, not only the saying looks arent everything for people but its true for washing machines. I have gotten multiple mail from co. wanting me to get extended warranty. Think I will, usually dont, cause I think it wont be reliable. Wish I had my washer from the 70s and 80s. Plain old wringer that got things clean. Just put black pants in dryer on very low heat taken out damp cause I dont dry a lot of my clothing. This seems to have helped to remove stains (soap)/ lint. but, talk about wrinkles, oh boy, this machine has that spin cycle going 100 miles a minute. And if you pick a lower spin speed things come out wet. I actually can say I hate this Maytag Bravo. Things dont come out clean, wrinkles beyond control, very loud. Please folks check out your sites on the internet before buying Maytag.

I purchased the Bravos X washer approximately 13 mos ago. Washer was noisy and has deteriorated since installation. I questioned the ability of a non agitator appliance getting close clean but was assured it would. Not the best if clothes are just moving against clothes. The machine had a difficult time in between adjusting to wash balancing a 3x event upon starting. It leaked intermittently during spin cycles and stopped due to unbalanced loads, sometimes refilling and stopping again. Now it wont spin at all, circuit board problems! This is my first and last Maytag. The company will most likely not balance/compensate on the purchase price (like the Bravos X) because it is beyond the 12 mos warranty.

I purchased a Maytag dishwasher in 2013 and the control panel needed replaced within the warranty period. About a year later, the control panel started to malfunction again, this time out of warranty and Im told it will cost over $350 to repair. I paid a lot for this dishwasher and thought I would get years of use out of it. I plan on buying a new cheaper one (not Maytag) for a little more that the cost to repair the Maytag. Im very disappointed and will not purchase another Maytag. I also read online that Im not the only one experiencing this problem.

This Maytag oven has lasted my mom for over twenty years. Now after her passing the oven is now serving me and my family. Have had it soon to be three years. Just now having to replace one of the eyes.

First let me say I have used Maytag products for 46 years. A little over a year ago bought a new Maytag Centennial Washer (Model MVWC555DW) for a cousin which was responsible to looking after as he had been brain damaged since birth. Needless to say when I started having trouble with clothes not washing and having to bring to my home and wash was not satisfactory. This machine never worked right but until after the 1 year warranty could get by. Needless to say I will never buy another Maytag appliance but now have a Maytag washer/dryer, stove and dishwasher in my home. Maytag is Not the quality that is use to be. WOULD NOT RECOMMEND THIS MACHINE AND ALSO UNDERSTAND FROM LOWES THEY HAVE HAD A LOT OF TROUBLE WITH THIS MODEL.

The Maytag MGR5875QDW oven does not come up to temperature. It might start, but then it will give 2 dings and show a failure. I have called the 800 number in the manual. There’s no good help. I turned the power off and then on. It’s no help. This a pain in the rear end. That is a kind way of saying it. Home phone is **; cell phone number is **. Call me any time. Thank you. You do not want my wife to go on the internet!

I would have given this washer/dryer a 0 star, but wasnt able to. Bought the pair and first thing, couldnt get enough water in the tub, clothes wallowing around for an hour in the few cups of dirty water that it allows. Cant even believe how terrible this combo washer and dryer is! Now I get to wash everything in this piece of ____ twice, thank you Maytag! Just took out a load and it is dingy and stinks, so now its wet, on the floor waiting its turn to go back for another wash (possibly even a third).If you want clean clothes, do NOT get this washer. Dryer has issues also. For whatever reason, the AF signal has been on for a couple of months. Turn it off and back on and its okay for a bit, then back on. Its the Air Filter. Its not plugged, so I dont know, I just keep using it with intervals of resetting it altogether. What a total waste of money. Am going to give it away for free as soon as I find a replacement! Save yourself a huge headache and look elsewhere than Maytag. Oh, and if Maytag happens to read my review, you can contact me for a refund any time, just respond to this post, you can even come pick it up and get it out of my home. Thanks a bunch!

Just purchased a maytag dishwasher from home depot. I did the install myself. The dishwasher will not work at all the panel lights up, but no water goes into the washer. I now must wait two days for repair. After reading all the other reviews, I am thinking about returning it for another brand. And yes the water supply is on. I have hooked up several dishwashers. This is the first time a brand new one did not work right from the store.