I purchased by Maytag Bravo from Lowes exactly 1 year ago when the gearbox failed. There was a loud grinding sound as the washer tried to shift from wash to spin. Reading through some on-line reviews and complaints it turns out that this is not a new problem and has been known to Maytag for some time. I specifically bought a Maytag because of their prior reputation for quality. Unfortunately, my information was out of date. It is so sad that a company would compromise such an outstanding reputation.

Purchased an expensive brand new home which had Maytag appliances in it. After about 1 1/2 years the freezer bottom began to constantly freeze and drip onto my floor. I researched the issue and found it was common, simply thaw the area where it freezes. Did it multiple times, we do not overfill our freezer etc. We must take the ice out of the bottom every 4-5 days. My hardwood floors are destroyed now. We purchased a Samsung fridge freezer bottom when they first came out years ago, had it for 7 years, 0 issues, but it went with the house. Now my Maytag oven door is locked shut, also it takes a very long time to boil water. Maytag junk. I am going to buy another Samsung fridge tomorrow.

Maytag dishwasher model #MDB7609AWB2 - The control panel on this dishwasher has just gone out for the fifth time since 12/10. Last time I also had to replace the control board also.

Have had Maytag HE washer for 4yrs, so far it has broke down three times. I contacted Maytag and they asked if I had bought extended service contract? No I paid $700.00 for this washer and had expected it to work a little longer than 2yrs before seal in door is cracked. Would NEVER buy another HE or Maytag product again!

Our new washing machine (Maytag Maxima XTLM Front Load Steam Washer & Dryer w/ Pedestals) has developed a loud knocking while running which the authorized whirlpool repair provider said was due to internal ball bearings. He said that the washing machine caused the pedestal to become warped and the only way to stop the knocking was to replace the pedestal. Whirlpool refuses to replace the pedestal saying that the pedestal must have come that way or was installed incorrectly or was overloaded. There are only two of us and we never overloaded at all. The knocking started several months after the installation. If the pedestal was defective (came that way), why wont Whirlpool replace it under their warranty?

Our washer, still under 5 year parts and labor warranty, wasnt functioning properly. We went through proper procedure having repair personnel first attempt to repair; waited over allotted time for replacement parts, wanted to attempt to repair again, then to replace with sub-standard model. We are now in our 5th month of being told 3-5 business days, 10-14 business days, and I was just told it will be weeks (after waiting 19 days) that replacement will return our call as they are 4 to 6 weeks behind. I have pages documenting dates, times, names, departments and excuses. What can I do at this point? What are my options?

Maytag used to have a reputation for quality. Their low water energy efficient Centennial is a waste of money. Half of the time clothes come out wet and most of the time they are still dirty. Also you are only supposed fill the tub 1/4 of the way with clothes so you end up doing 3 times as many loads per week. What genius came up with this idea? Save your money. You would get better results washing your clothes in a tub with a washboard. Seriously!

Within the first six months the drive on the washer went out. Had to order it from another city cost over 200.00 for it then had it put in. The dryer works most of the time but now and then it just dont dry all the way.

The washer machine is only 2 years old and its broke, at first it wouldnt spin and now it wont wash. Everyone is saying between the parts and service fee, it will cost 200 to 300 dollars or more to fix, most technicians wont repair them because they say that we may as well cut our loss and just buy a new one. No one likes these machines. I wish I would have known what a sham the washer machines were before purchasing.

Maytag/Whirlpool dishwasher control panel FAILURE MDB7749SAM - Just like all the above comments about this dishwasher... I too have been a victim. Control panel stopped working after 1 1/2 years. Turned on by itself like other have commented and will not let you push any buttons. Maytag/Whirlpool refuses to do anything about this at all and will cost me over $250 to fix an appliance I purchased at $499. How disgraceful of a company to not stand by their product... A huge shame on you Maytag/Whirlpool for not standing behind your product. If anyone knows of a way to get involved with a class action suit against this company I would like to get in on it.

I bought the Maytag stainless steel refrigerator with the top double doors and bottom freezer. I paid $3000 for this thing and the ice maker has broken twice, an ice sheet forms on the bottom of the freezer and the drawers broke due to being cheaply made with plastic. I had the old style refrigerator for 15 years with not one problem. I think these newly made appliances are made crappy! Will never buy a Maytag again!!!!

My washer is new, out of warranty, and about 2 and a half years old. All of a sudden, with no warning or previous issues, the computer board in the washing machine malfunctioned which caused a humming noise, it would not cycle into the next wash phase, the time would go up instead of down, I could not change cycles, and when I would push the power button there would be a delay of power coming on. I unplugged and called my local appliance repair and he said he sees problems with this model regularly, although not always the same issues.Before purchasing I scoured the internet for reviews on different units to make sure I didnt get a lemon. I think Maytag saw the error of their ways quickly and stopped making these before people caught on. This model is no longer being made. I like matching units, so it meant either shell out $500 for replacing the board, or replacing both the washer and the dryer that still works, which would be about $1200 or more for a new set. I chose the least expensive route for now. Not that it matters where I bought mine, but Home Depot and it was on clearance so it was a good price. I have now made up for that difference in repairs.

I give the product lowest and poor rating. The bearing in our washer went bad 4 months after we bought it. For the fourth time, they are coming out to repair the washer on 01/11/2012.

Updated on 10/09/2019: Well I wrote a review on my brand new Maytag washer that we bought at Lowes in June. When I wrote the last review I was waiting for our repair. They did come to repair and I was told by the repair guy (keep in mind the washer was only 2 months old at the time) that there were 3 fail codes. He said that it was overloaded or loaded wrong.That you cant wash towels with sheets, you cant wash any kind of rug no matter the size, which I only wash small bathroom rugs that are NOT oversized or heavy, you cant wash tennis shoes (which I have not). So I asked him what is the point of investing in what is supposed to be a top of the line, heavy duty, extra large tub, commercial washer? He said that you cant do that with any machine. I told him our old washer that we had 13 years had no problem with washing towels & sheets together. My point is that I am 100% disappointed in this washer & I encourage you to NOT buy Maytag, apparently they no longer live up to their brand.Original Review: We did our research & comparing & this machine came up on top. Its size suites our needs & we were excited about all the great features. We purchased it in mid July of 2019 so its 2 months old & for the last month it started to shut off in the middle of a wash cycle. At first we thought that maybe we were doing something wrong. So we would re-start it & it worked. Fast forward 3 weeks, it was doing it almost every time. Now it isnt working at all, it starts to fill up then shuts down before it starts to wash.Today is a Friday & I called Maytag to request a service call under the warranty (60 days old) Maytag had me on hold for 19 minutes before I could even talk to someone! The customer service person (once she was on) was very nice & sympathetic but couldnt get anyone out to service our machine until Tuesday, which is a HUGE inconvenience since we have not been able to wash for the last 3 days. I am highly disappointed in the machine for the simple reason that I paid for a new topnotch machine because my old one that 13 years old finally gave out & now am in the same situation & in for $1000 I paid for this new washer & having to go pay to do laundry 2 MONTHS later! I will add to my review once they have performed the service call to see if the issue is resolved or the machine replaced if they cant fix it.

I have a Maytag Range that I bought new and installed 6-1/2 yrs ago for over $1200.00. I am single so I rarely use the ovens. The upper over I use maybe 1-2 times a month and the lower oven I may use once a month. The night of 3/7/2016, I used the cleaning cycle set on medium for both ovens. Yesterday, when I went to wipe the ovens down, I found the lower heating elements, on both ovens, had snapped. The top ovens lower bracket had broken in 2 places, the first break is about 2 from the connection, on the right side leaving about an 7 gap. The lower ovens element had broken in only one place about 2 from where it connects into the back of the oven. This has to be a flaw in the either the design or the material. In the 45 yrs that I have been using ovens and stoves, my last stove was over 35 yrs. old, I have never had a heating element break. While I can understand a break at the connection, I can see no reason that the it would break in the center of one side on both lower elements in the same oven. I also noticed that lower heating elements are a much small gauge than the top which I find strange.The other issue with the stove is the seals around the windows are not tight. I noticed dust was inside the two glass panes. The rubber seals were sunk down into the door, but Maytag said it was not their problem that I must have done something. When I remodeled my kitchen, I bought all Maytag products: 1.H20 Frig - The electronic panel went out after 3 months and had to be replaced. Manufacturing Defect - When the repairmen came to fix it, he told me to call Maytag which I did. They refused to pay for the repair because I called a repairman first, even though the business was Maytag certified. Even though I said I would cancel the service call they said because I had made the appt. and they recommended I call Maytag, they would not cover the repair. 2. Stainless Steel Dishwasher (Cost over $700.00) - Motor went out after 3 yrs. 3. Microwave/Convection Oven (above the stove)- Convection light out after 4 months. The replacements are not inexpensive.One other complaint I have is when I bought all my large kitchen appliance Maytag had a $600.00 rebate offer. Even though I mailed all the required documents to the company over 2 months before the rebate ended, I never received my rebate. The explanation I received was that the center that received my documents delayed forwarding them to the proper department that processed rebates and they were received after the offer ended. When I questioned the legality of the practice, I was told that this was all explained in the Terms and Conditions (ie: small print).

Same issue as everyone else. Bought the French door with middle deli drawer fridge November 2012 at Home Depot. After 2 1/2 years freezer drain froze up leaking water into the floor. Spent 6 hours fixing it. Now still less than 3 years old the ice maker is not working. Not a jam or water supply issue. Just dead. Looking into replacing the ice maker. Such a disappointment. Only thing this fridge is good for is its looks. Obviously common repeated defects. Wake up Maytag and accept some responsibility.

I just bought this piece of junk... Like everyone else I guess I didnt do enough research! I have had this washer for less than 3 weeks and just like everyone else I am so disappointed in how it tries to wash without water! I too have tried different settings. I had to wash a load 3 times... pausing it while trying to get the rest of the items wet. Its ridiculous... of course now to try and see if I can return it! Yah right... Home Depot does not have a good return policy and Im afraid I will be out 800+ with this washer. This is ridiculous! It really is.

Washer sounds like gearing is broken, is noisy during operation, various combinations of options dont work, appearance of only one agitation cycle combination on washer, just many settings but all with the same response; dryer does not timely dry clothes, all settings default to the same palpable heat temperature; clothes take much longer to dry in new dryer than they did in old Maytag. Newer Maytag set appears to be secondhand garbage sold as new by Menards. Company unresponsive to complaints.

3 year old Maytag Washer model MVWX600XW broke. Paid $345.55 for extended warranty. I had to wait 10 days for Appliances Unlimited to fix the washer in Sept. then the washer broke again in November needing 3 more parts including a motor. It took almost 2 weeks for Appliances Unlimited to come to the house, then I have to wait 5 weeks for a new motor to be in stock.

Bought va washer. Trying to upgrade. Water fills about 1/3 of way even on bulky setting. Supposed to be high efficiency. Detergent does not get all the way out because there is no enough water. Have to put it through 2 rinse cycles. Worst machine. Design is flawed. Clothes all wrinkled. I cant afford to buy clothes and have them ruined. Man must have designed. Hate the washer. Im poor and they want take it back... want my money back. I cant buy washer every day. I will keep on complaining. No customer service. People just put you off. It is a Centennial high efficiency. A piece of junk.

I have a two year old version of this dishwasher (MDB894995BB3) and now the start and cancel light on the control panel stopped working. I now see that this is a common theme with this model and I feel it is their obligation to repair these units with permanent fix and not the same thing that will fail again. I have 3 different Maytag appliances all bought 2 years ago from Home Depot and they are all broken. I will never buy a Maytag product again. I might replace this dishwasher as I know it will fail again. 2 years on a dishwasher is a complete failure. Unreliable Junk. Do not buy Maytag.

The washer does not get clothes clean at all even with the help of odor blaster, does not spin right, does not even out the clothes, walks while it is spinning. My towels do not smell good at all. The dryer gets too hot and the lint trap is always a mess even though I clean it after every use.

Why is it when you wash dark clothes they come out with white spots which looks like soap. I have put very little soap and it still appears. I usually wash in cold water so I tried warm water - same result. I have had a Maytag for a least 40 years never had this problem - what is it I am doing wrong? I have to wash and rinse at least 2 more times. I would appreciate a answer so I can fix this.

I purchased a Maytag Bravos XL Top Loading Washer and matching dryer in 2013. I had a repairman out to install a new screen on the dryer because the lint was spilling over into the surrounding area. The new screen has been catching most of the lint, but I still have to vacuum the surrounding area after a few loads. Also, I have to turn the dryer on two (2) cycles in order to dry most of the clothes, and the machine makes a lot of noise. Those are minor problems compared to the washer. It constantly tears holes in my towels and wash clothes. I NEVER put in a full load because the water level is so low, and it does not clean the clothes. It takes a long time to go through cycles and it is EXTREMELY noisy.I called Maytag and they said that they never heard of the problem of creating holes in towels and wash clothes, and wanted to charge me over $100 to have a repairman come out. They also said that the repairman might not find anything wrong. I feel that the washing machine is very hard on the clothes - like the salesman at Lowes said It’s like beating the clothes against a rock. The washer and dryer are JUNK, and I would not recommend these to anyone! I would trash them, but they were very expensive and we cannot afford to buy new at this time.

I have owned this Maytag washer model # MVWC360AW0 since Dec/2013. I do not have a single complaint about this machine. It has worked flawlessly for 5 years and am very happy with it. I just follow common sense maintenance like cleaning it once every month (do a full cycle with just borax & baking soda 1/2 cup each) no clothes of course. Another thing I do is to leave it open after I am done washing so it dries completely before I close the lid. The washer looks and works like new, cant be happier...

I purchased the Maytag metal interior two years ago, the very first year I had to replace the control panel board... Now, the panel went out again, after calling the Maytag executive office, they finally sent me the part, telling me I had to pay to get it fixed. That was just three months ago... Presently, the dishwasher has quit running water in the cycle... I will NEVER purchase another Maytag dishwasher... thinking you get The Best doesnt mean what you think... BEWARE...

Purchased the very top of the line Maytag Washer and dryer.. Top loader MVWB955FC1 washer. I got this huge washer and dryer because I was tired of paying $20 to have my Cal King comforter laundered. Bad idea.. Yes the comforter fits easily in the drum of the washer but it does not even come close to clean.. Why no agitator..? It leaves soap all over it in addition to the dirty laundry smell.. The dryer is better but it takes at least 3 cycles of taking it out and un-wadding it to get it all the way dry. Now my wife just hangs it on the line.It has been just over 3 years Feb 2017 since I bought both units from HH Gregg.. Now the top of the washer around the soap dispensing orifice has rust bubbling up worse than my 25 year old unit I put by the curb.. Maytag support is no help.. “Sorry rust is normal and it your unit is out of warranty”. I asked If this would have been covered under warranty.. NO!.. Not unless you report it within 30 days.. We only use it once or twice a week.. What terrible service..

This machine (Maytag Bravos XL) was in our new house and is relatively new. It is the worse machine I have ever owned. I am 58 and cant reach the bottom of the tub to get clothes out. It doesnt fill with enough water to clean the clothes, and repeatedly I have my clothes coming out dirty. I have had to rewash clothes to get them clean at all. Or they come out with grime all over them. I had both a LG and Samsung front loaders in the past, if I could afford it I would throw this Maytag out on the curb! Its a piece of junk.

We have a Maytag dishwasher that came with the house we purchased in 2012. Im not sure of the exact age but the former owner said it was a relatively new installation. The appliance works very well; cleans well. Just a couple of things of concern. First, it is really noisy. The fact that we can very clearly hear it running in the adjacent room does not speak well for it in this regard. The other things that has occurred is that rusting is evident on the trays of the dishwasher. One of the upright pieces has already broken off due to rust and two others are close to coming apart very soon. Nothing sharp is placed in those areas that are coming apart so there would be nothing remarkable to disturb the plastic coating on the wire racks. I can only conclude that the plastic coating was defective at the start; hence the rusting at the base of the upright pointing racks. That said, it does clean well but I dont foresee this unit lasting much longer overall due to the rack damage that is continuing to occur. I would expect the racks to at least last as long as the dishwasher but this does not seem very likely at the rate the racks are deteriorating.

Oven worked ok for a year and went under right day after warranty expired. I called factory-approved repair people in Brooklyn but was told repair would cost more than buy new oven. I contacted factory but got no help either.

Bravo XL - This is the worst washing machine I have ever purchased! Loved it at first but after a year or so we couldnt wash a full load without error messages. Then we couldnt even wash one pair of jeans without an error message. Called to have it repaired and $300. Later the bearing was replaced and the washer worked wonderfully once again. Less than a year later and we are back to having a non functional washer. Cannot wash anything without the error message. Customer service is absolutely no help. For such an expensive washer and supposedly a good brand, this machine is a real disappointment.

I purchased a Bravo washer and dryer set about a 2 1/2 years ago and had problems from the start. The dryer control panel went out the first day. No problem, they replace the panel. The washer is a different story. The agitator went out next and the wait time to repair it - 3 WEEKS. The agitator went out again for the second time and the tech stated that it had to be replace. Wait for it. Waiting time - 1 month including parts. To make this story short the agitator will go out every 4 months and the tech stated once its been replace it will work like a new washer. Wait for it. The agitator has been going out ever since and the wait time average 3 WEEKS. Wait for it. This Maytag is trash.

I purchased this washer in Oct. of 2017. From the beginning, it has not cleaned clothing properly and leaves a white residue on clothing. To get the residue off, I must wash the clothing again or sometimes it will come off in the dryer. The water level is too low to efficiently clean. I thought I would save water getting this but not at the price of multiple washes... What good is that? Since there is no agitator the clothes just sit at the bottom and move back and forth as one big clump, with just a few inches of water. I am sorry Ive waited so long since I am now past the point of returning this piece of junk.

I have ALWAYS bought MAYTAG since the 1970s. But MAYTAG is no more. Whirlpool bought them out. I have an HE (first mistake)... HE... will go away just like low flow toilets did!!! You cannot wash clothes in 4 of water. I bought a top loading Brazos XL for $1100 (second mistake)... Have had it just over a year! I should have returned it but did not. Huge mistake (#3)... Repairman told me to get rid of it as fast as I can. Will eat me up in repairs. Now needs repair again for another NEW issue... The fill sensor does not tell the machine to load the proper amount of water. Now I cannot clean washer, tried three times last night. I am beyond upset. Repairman said buy GE! You can bet it will NOT be High Efficiency!!!!!

I am so sorry to see so many people having the same problem. Maytag Dishwasher Model #MDB7749AWM2 purchased 12-10-11. Control Panel needs replaced (260.00...service call, part and labor). Writing this as Ive spent the last 20 mins on hold with Maytag. Im demanding them to make this right. Ive been told by Trisha at Maytag not to believe all these post as people tend to exaggerate the problems. Anybody have info on class action lawsuit? ?

Does not wash. Only very small loads get washed even though it claims to wash bedding. Some clothes NEVER get wet. Many times the clothes have to be rearranged and re-washed AND extra rinse. Cycles are over an hour each (then multiply x2!!). Maytag service has been called MULTIPLE times. They replaced the touch pad then the computer board. Both times saying the machine works “according to design/specs”. This is a Very poor design. Maytag should recall this inferior machine as it does not perform the job it is being sold for.

We purchased our Bravos XL Washer and Dryer from Home Depot in November 2012. We also purchased the three-year extended warranty. I just replaced the washer today, and definitely NOT with a Maytag. We only spent that much on the Bravos XL set as we were heading into retirement and wanted to update our appliances. Maytag has always had a decent reputation, so we decided on this particular set.This washer was a terrible purchase decision. The drain hose had to be replaced due to leaking. We handled that fine. However, just past the extended warranty period, the main bearing went out. Also, the transmission was going out, and the washer was spewing nasty black fluid all over from underneath. The repair was going to be a minimum of $750.00 just for the bearing and tub assembly, and the repairman was honest and said it wasnt worth it, to just replace the washer. We didnt even discuss the transmission issue. We were more than a little disappointed in the duration of life out of this washer. I had my other washer for 20 years plus. Thankfully, and hopefully, the dryer will remain in good working order for some time.Being a senior, this was not the expected lifetime I was after out of a major appliance. I dont need this sort of expense every four years, or less as Ive read on these reviews. On average I do 2 to 3 normal sized loads of laundry a week at most. Not good Maytag, not good. If there ever is a class action suit in regard to these machines, Im interested!

Maytag Bravos XL MCT (Disposable). Model number MVWB835DW3 Top load washer. I’ve read many of the reviews on the site and feel your frustrations. Let me start by saying, at least you have a choice of products. I’m stationed in Okinawa Japan and have ONE place to buy my appliances and a choice of two machines. Both of them are garbage Maytag products. The first one (model noted above) died after 18 months. NOTHING they could do! The “technician” they sent didn’t have a clue. His answer was to replace the control board. Time to receive part? Up to 30 days. Really! My option? Buy the exact same product. I can’t even describe how screwed over I feel.

Have owned Maytags (washer and dryers) for 40 years. I bought a Bravos top load washer and matching dryer because we gave our old set to a daughter leaving for college. That was less than four years ago! We bought this because it conserved water and there would only be my husband and myself home. So laundry needs would be minimal. The washer quit draining and starting making a terrible noise several days ago. Immediately called repair service - I knew from the onset this was going to be a big problem because when I told them the model, they responded - uh oh! Two days later service man comes to assess repair and lifts machine up and tells me bad seal has leaked to gear box and ruined it. Soooo for a machine that is less than 4 years old, I will have to pay $280 for part, $79 for service call, $60 for labor and $35 to have them pick it up and redeliver (because the repair is too big to be made in my home). $454 for a machine that gets minimal use!!!! I can add another $100 plus and buy a brand new machine. Why should I have to??? In doing some research, I found out this is a common issue with this model and Maytag has paid for the repair of other washers because it is a common problem. Even the serviceman said that and recommended I get a hold of Maytag. Their response - sorry mam you dont gave an extended warranty. (NOW I HAVE A LEMON!) Guess my next step is to write a letter to Maytag Corporate Office. I will keep going up the ladder until they address this flawed machine problem! One thing is for certain - I will never ever buy another Maytag product of any kind or will I ever recommend it. They are just not reliable. Guess, nowadays they are considered throw away products - keep them a few years and throw them away because its not worth your money and effort to repair them :-(

My Maytag AquaLift Range MGR8880AS0 was given to me in September 2014. While the range top was excellent and gave me no problem, the so-called self-cleaning is a total joke. I do not do a lot of grease baking or broiling so I have not needed to clean the oven only twice. The first time was a total surprising astonishment. When I opened the oven immediately after the cycle was completed, the oven was not even 350 degrees, most of the water was still in the oven! This happened shortly after a family crisis (my husband became ill and died), so I did not do any inquiries regarding the cleaning failure. Today, January 24, 2018 I decided I would do my second cleaning. Wow, it was a total and complete failure. The oven was barely warm.I always had a Maytag washer, way back in the 1970/1980. My four children grew up with the Maytag, So, I think when one of my children decided to gift me with a new range after a change in location, the Maytag name was at the top of the list. Unfortunately, in 2014 Maytag was no longer what it had been way back in the olden days. The name Maytag does not stand for what it used to stand. End of my story. Thank you for giving me the opportunity to get this off my chest. Since this was a gift, I do not have a receipt. However, I have an insurance renewal due advice (coverage expires 05/24/2018).

I bought the Maytag Bravo XL MVWB725W washing machine and dryer pair in August of 2015. 2 months after I bought the pair the thermostat went out on the dryer. It was under warranty so it was fixed and no problems after that. In July of 2016 I have my first stainless steel hose break at the fitting because of corrosion flooding my laundry room. I thought it was a fluke so I put another one. The next hose started to corrode in September 2016. We thought there was some weird chemical reaction going on between the hose and the filter on the back of the machine. So we changed to rubber hoses in September. Since then we have gone through 6 sets of rubber hoses. We have had the water company out, they say our water is fine. A plumber out, our new water heater is fine as is our plumbing. An electrician, who changed an outlet and put a grounding wire on our house water line. And an appliance repair man, he found the problem so he called Whirlpool who makes Maytag. There is corrosion on the water temp control. However nobody has EVER seen this problem and doesnt know how to fix it. Not even Whirlpool. And Whirlpool says its my house. Im at a dead end with a washer that is constantly going through hoses. It really doesnt wash clothes very well either unless you put a lot of stain remover on the clothing before and wash it in hot water. And yes it is noisy. Dont buy this product.

Same issues as many others here, had to replace the main control board a couple of months after the warranty period was up. Funny thing is though, I brought the old board into my local electronic repair shop thinking it might be worth getting it fixed in order to have a spare on hand in case the new one was also short lived... He told me he examined the board and there was nothing physically wrong... The problem he said was in the programming or firmware. Unfortunately, he said Maytag does not offer an update and there is no way to clone the newer version from my new board onto the old one so it was garbage. Seriously Maytag? Hundreds of dollars later in parts and melted groceries all because you wont issue a firmware update? Also have water leaking out of the bottom of the fridge late at night so Im never awake to troubleshoot it. Considering how sporadic it seems to be, Im guessing it must have something to do with the defrost cycle... Have to figure it out though as its starting to cause damage to the floor and leaking down to the basement :( Never again Maytag.

Purchased Maytag Jetclean Dishwasher Model # MDB7749SBM3 on March 19, 2014 and on June 10, 2017 the washer would not go through the cycles properly. So I got on the internet to check out the problem. Maytag has very flimsy wiring circuit on the back of the control panel that rusts out due to being close to high-temperature water. Obviously a design flaw. The only way to fix it is to replace the control panel for $150 dollars with another flawed part. Do not buy Maytag dishwasher.

Dishwasher MDB7749SBM - Have the same problem as everyone else, panel board (2nd one, 1st was under warranty). This panel W10475787 is 2 years old. Keeps lighting up doing what it wants to do. Dishwasher is 3 years old. Cant find out if there is a recall on this part (there should be).

Since day one, no matter the size of the load or how careful I place the clothes or what level or water, washer vibrates and moves around the floor. I have had service out twice to recheck level but it still vibrates. Worst washer ever. I should have spent the money to repair my 20-year-old Kenmore.

I bought my Maytag in 2013. It worked fine at first but for the last year it isnt getting clothes clean. In fact, some look like theyve never been washed. I have to run the rinse cycle 2-3 times and they still seem somewhat soapy. The washer still leaves clothes drippy after running the spin cycle. It takes 2-3 hours to complete a small load. I wish I had my old Kenmore back. It worked fine for nearly 20 years!

My Maytag model MMV4205BAB microwave turns on and heats when the door is closed. We paid a lot of $$ for this overhead microwave and it has not been a satisfactory product. The turntable broke within a couple of months and now this. Im afraid it will burn my house down. This is a defective product and in my opinion it should be recalled. I have read several other posts about this exact model and problem. We purchased all Maytag appliances for our new home and we have had problems with all of them. The auger on the ice maker on the freezer broke within a couple of months. The handle on the oven door broke off while the builder was installing the appliances, and the top of the line dishwasher doesnt clean the dishes. It leave deposits on everything, no matter the detergent used. Ill never purchase Maytag again!

So for the past year our 1 yr old freezer has been leaking and holding a sheet of ice at the bottom. Ive been wondering why my electric bill has skyrocketed the past two months and we just realized that the freezer wont even stay closed anymore. Maytag has become a VERY POOR product. Our less than two year old $450 Maytag Drier just busted as well. After paying repairman after repairman and replacing different parts, we had to get rid of it. I am very dissatisfied with Maytag and will never purchase a product with their name attached. Please keep us posted if there is a class action lawsuit. This is unfair to make a product that fails immediately for the price that is paid!

I bought a Maytag Bravo without an agitator. Regretted from the 1st load. Some of my clothes do not even get wet and I bought the commercial grade. My 20 year washer that was on its last leg washes better than my brand new Maytag. Please do not waste your money, your clothes will not come out clean.

I absolutely do not like the fact that you can’t choose what size load you have. The washer wants to do it for you but it is not very good at it. You have to fool the washer to get any kind of water level or just use the deep fill every time which is what I do in order to get the clothes clean! This defeats the whole purpose of trying to save water. Also there are too many settings. I mean we’re just washing clothes here not flying a jet. I personally would prefer dials instead of the digital instrument panel. So much easier.

We have owned the dryer (Maytag Bravos) since Dec. 2010 and are now on our 4th service call. Upon the second delivery of the part that was ordered last week - we will be on the 5th service call. I finally asked Maytag if I could get a trade in since this dryer is obviously crap. They said they could only handle the problem at hand, which is the same problem over and over and over. The flywheel was left off all together. The pulley belt for the dryer pops off about every 4 to 6 months. Ridiculous. Its a crap dryer, dont buy one!

Wish I had reviewed Consumer Affairs reports. When our old Maytag stove required repairs we decided to upgrade old stove instead of putting money into old unit. Looks like a huge mistake. Not only was there a delay in receiving unit after placing order but oven will not preheat. Two weeks before Thanksgiving we were promised a working unit. Now we are only 2 days from Thanksgiving, 2 repair companies have been at home to repair. Requires new circuit board and a new regulator to repair and no promise we can obtain parts. Now I have to figure out how to feed my family for holiday. I am pretty well done and after reading other reports that they are better in junkyard I think I will try to make them take back this defective Model 8800 product. Sitting in our kitchen unusable for the holidays. Dont buy Maytag as customer service does not exist.

This product has cost us thousands of dollars in clothing!!!!!! We have a lot of pictures to prove this!!!! Greg Mackie Major Appliance does NOT back this product or US the consumer!!! We have bought THREE households of products from this distributor & they have NOT backed any of the products that they have sold us, or given us Any discount for repeat business or loyalty and have NOT Supported us in any way whatsoever!!!! We have spent thousands of dollars and have had NO compassion or support whatsoever!!!!!! We expect a full refund for this Failure of YOUR product & a NEW Machine that will CLEAN our clothing & NOT DESTROY it!!!!!! Very Disappointed in this Product!!!!!! We Will NOT purchase another product from Your Company or from this Distributor unless YOU make a conscience decision to make this situation Right!!!!! We Will Spread the Word about your Failure of a product & detour business from YOU & YOUR Distributor!!!!!! We have numerous other photos to share with consumers of how YOUR product has destroyed our clothing!!!!!

Holds a lot of laundry. Spins laundry almost dry so its quicker in the dryer. Easy to load. Easy to add wash soap and fabric softener. Only problem is its very deep to reach the laundry at once its done if youre not real tall.

Never waste your money and buy Maytag washer. Mine is XL large tub and has extra wash for extra clean. Dont waste your money. Never fills up with enough water. Almost everytime I wash I have to rewash the load because the clothes are still dirty, have soap spots and most of the time the clothes didnt even get wet. Horrible Horrible washer!!! My water bill has gone up a lot because I have to rewash the load so thats twice... I cant even use the XL tub because it wont fill up with water. Horrible product. Cant believe Maytag is still in business. They dont stand behind product. Called. Complained. They gave me nothing except for some free pods to clean a washer thats only 6 months old. Ive tried every cycle to see which one will wash the best. Still Horrible Horrible. Doesnt get anything cleaned. Here I thought nothing could get worse than a front loader? Well the Maytag is worse Horrible product. Dont buy. Dont waste your money. Try another brand!!!

We purchased a Maytag dishwasher MDB7609AWS2 in October of 2010. It first stopped working about 2 years ago. Since it was only 2 years old, we were disgusted and decided to let it sit and do dishes by hand. About 2 months after it had stopped, we tried it on a fluke and it worked. It stayed working for about 2 years. It finally stopped again, so we did the same thing, just let it sit. Every once in a while we try it to see if it works. It just recently started working again. We are wondering, what is up with this. We are not sure why or how the sitting works, and it is ridiculous that you have to have an appliance that you cant use periodically. We were too stubborn to have it fixed or buy a new one at this level of newness. We will get by in this manner for at least another few years, so as not to have lost all of our investment in a dishwasher, but we have sworn off Maytag appliances forever.

A week after warranty expired, our 1 year old Maytag gas range (model# MGR7662WS 4) required new Direct Spark Ignitor (DSI) board. Knowing it was just beyond warranty, I inspected wiring first and found that the Bake connector on the DSI was loose, flopping around from a bad solder point on the board. Called Maytag and informed them of this manufacturers defect and all they offered was a $20 discount on a replacement part ($220 instead of $240). It worked with new part for 4 days, then something else went bad causing oven to spark, light, heat to less than 100 degrees, then shut down, then restart, then shut down, then restart, then stop doing anything. It has never worked correctly since then. How can a manufacturer of almost all domestic brands get away with such shoddy workmanship.. Taking advantage of defective or poor quality parts to sell more of the same when they fail and for an enormous markup? Where are the regulators who oversee monopolies and blatant scamming of American consumers?

I have to say I am terribly disappointed in the quality of my Maytag Side by Side Fridge/freezer and my Maytag stove. Having sold Maytag commercial washers and dryers to coin laundries for over 20 years I expected better. Needless to say..... these are Whirlpool machines with Maytag name plates. Not the Maytag quality that was produced in Newton, Iowa. You can tell these are plastic machines made in Mexico. Of course you still pay for the Maytag name just not the quality. I have always tried to buy from US companies, but my next appliances will not be as Whirlpool is the only US company left with exception to very high end products.

I purchased a Maytag Bravos Quiet Series 400 in 2010 and it is now leaking like crazy and sounds like the bearings are going or gone in it. I researched washing machines for over a month before purchasing, and it seemed like this would be the machine for our active family. So much for research. It washes clothes okay, but is a bit rough on them. I found that it has ripped some of my more delicate items. When I contacted Maytag, they sent me an email with contact information to purchase a maintenance contract for $395 which would cover the machine for only 1 year. My husband is very mechanical and took the washer apart thinking the seal/gasket may have come off. He cleaned up the seal and the area around it, and put the seal back on. It did not help. He also noticed that the drive shaft to the motor was beginning to RUST! This machine is only 2 1/2 years old! So, if you are noticing that your whites are getting orange spots on them, this is probably happening to your washer, as well. Maytag should step up to the plate and recall this machine.

Although we have always had Maytags, this was the first time we purchased a front load washer. The Maytag Neptune washer smells and your clothes stink. We have purchased the most expensive laundry products, washed and rewashed clothes and have no other recourse but to buy new machines again. We will not be purchasing Maytag or Whirlpool. I would give it a minus 5 stars.

Dont buy a washer from Maytag, they put it together wrong and the transmission leaks so it will stop spinning after time and then it fries the motherboard. Too expensive to fix so you have to by a new one.. Their 10 year warranty is a joke and doesnt cover anything hasnt even been 5 years yet. Garbage products.

Just dont get clothes clean like the old agitators. Doesnt matter what brand you decide to get I guess. Had Samsung front loader before and was disappointed in that brand as well. Thought them both to be good buys... But miss my really washed clothes!

It is actually an older model Maytag set that I bought used 4.5 yrs ago. I am very impressed how its held up and how fresh our clothes are still. I have always loved Maytag and will buy again if needed.

Bravos XL MCT model#MVWB835DW. Bought this new. After 2 weeks called Maytag. Washing machine did not work. I called off and on for 7 months to Maytag customer service. During this time they tried to do troubleshooting over the phone. Sent technician out. He said that there was problems with this model, that they were working on updates and would get back to me. 10 months after installation, technician came out. Washing machine worked, but still took 2 to 3 hours to wash one load of clothes. Started calling Maytag again. Washer now take 3 to 5 hours to wash load of clothes. You also have to do extra spin cycles (1 to 9 times) to get water out. A year later they send technician out. He tells me that this machine wasnt made to do loads larger than medium, that it cannot wash heavy items such as sweaters, sweatshirts, towels, blankets or comforters. That the normal cycle is not to be used. This is not a working function on this model. It is there because of regulations. Called back to Maytag. They said it was out of warranty and that there was nothing that they could do.

I purchased a Maytag gas stove. Right away I noticed the oven racks would sag in the middle pulling the back corners to pull away from sides dropping the rack down on top of rack below. I got a hold of Maytag and they sent me out a set of 3 new oven racks that were exactly the same as the ones I had. I have been fighting with them for years. I called Whirlpool today who make Maytag and was told its off warranty and that I can order another set of oven racks at a cost to me. They would be the same as I have. The racks are so cheaply made and cannot stand even a few pounds. The finish on the stove also chips very easily. You rub a pan up against it and it scratches the white porcelain off. I spent a lot of money buying the dream gas stove I had thought, but only to be unsatisfied with my purchase. Buyer beware of Maytag products.

I PURCHASED A WALL OVEN ABOUT 4 months ago. Used the self cleaning, oven blew fuse and some other part, had to wait for almost 2 weeks for repair because of self cleaning liner is now peeling and leaving fine particles. Maytag said it was ok, they would not replace, the liner doesnt have a replacement part so Im going to have to buy a new oven to feel safe for my family meal.

Maytag top loader washer will not complete cycles. Washer is only fourteen months old. Repairman says parts will cost four hundred and seventy four dollars - almost what I paid for the washer.

My Maytag dishwasher MDB7749SAM is not quite 5 years old. At the end of December 2016 a bubble appeared on my vinyl floor. The plumber could not find any broken pipes or reason for any moisture to have gotten under the flooring. A flooring company did not know what was causing the bubble, moisture or the vinyl glue had failed. The floor got worse and worse, more bubbles.Called the flooring company again. Raised the register cover and could see all the moisture under the vinyl and underlayment. Plumber discovered the dishwasher fill valve had failed but because there was so much insulation on the kick plate, at the bottom of the dishwasher, it forced the water, which was in a pan under the dishwasher, to push the water to the back by the wall and under the flooring. Plumber said, the insulation acted like a dam to keep the water from showing in the front of the dishwasher. The first and subsequent bubbles, in vinyl were 3 feet away from the dishwasher. No way to tell the dishwasher had the problem. Has anyone experienced this problem? If not, take care to remove the kickplate and check your dishwasher for water problems.

I purchased this new Maytag washer (Model # MVWC300XW, Serial # 12621033) from Hahn Appliance Warehouse in Oklahoma City, OK 73107 on November 23, 2011. It is less than six months old, and the transmission has gone out. Hahn advised me that they had to go through Maytag Service, and they would only replace the part. I contacted Maytag/Whirlpool Service Corp. directly and spoke with a manager named David, who informed me he was sorry but would not authorize a refund or exchange for a better product because this was the first service call. I am very dissatisfied with this product and with the service standards that Whirlpool/Maytag offers on their products. If I were to sell a product that I knew has had numerous complaints, I would pull that product from my line offering and make either a full refund or replace with a higher level service product.

My family purchased a New Maytag Washer and dryer about 1 1/2 years ago! Thinking that the name was far more Superior than anything we could afford! What a piece of junk! The washer is nothing but flashing codes! Unlevel this and always stopping and starting over with a wash, when in fact it doesnt shake and bounce itself into the middle of the floor! As best as I can describe, it literally needs Hurricane straps to hold it down! You can never wash a full load because it cant handle it! Now! Onto the pathetic dryer! Several weeks after they were installed was the first scenario with the dryer! We had a representative that does work for Maytag warranty to come and work on it, after telling me over the phone that if in fact the lint trap had lint in it, that I would have to pay the service call! Funny!! So after diagnosis he said the belt broke that runs the exhaust fan! He said it was fixed and went on his merry way! Several months down the road! Same routine! Broken belt that runs the exhaust fan! And once again several more months down the road! Guess what!!! Yep!! Broken belt that runs the exhaust fan!!! So now here we are! I am now into the extended warranty that I purchased from the furniture store which was almost an additional $250.00! And voila!!! Its broken again! So being the fed up person that knows what the answer is going to be, I take the front off the dryer like I have seen done so many times before!!! And what to my surprise do I find?? Another Broken Belt!!! So I am wondering!! Why so many broken belts! So I take my flashlight and look at the motor and housing that holds the exhaust fan and I notice that in fact the housing that holds the exhaust fan is BROKEN! Therefore, this is the cause for so many broken belts!!! Well, who should be responsible??? I contacted the extended warranty people! What a waste of time! After setting an appointment for Sears to come work on the dryer and after explaining on several Recorded Phone conversations what has taken place! The service man comes to my home and not even 1 minute after entering tells me that he cant work on it because I have self diagnosed my dryer! What was the purpose in me explaining to them beforehand what I found??? Why didnt they mention then that I should not have taken it apart or hey put the front back on!!! Now after causing a ruckus with the furniture company that I have spent well over $50000 with!! They want to supply me with a 1 time Customer Courtesy!!! Of repairing the dryer!!! Oh did I mention that I am a Professional Diesel Mechanic for a major Trucking Company that is far more capable of diagnosing something like this than evidently the person they sent the first 3 times!! NEVER AND I REPEAT, NEVER BUY ANYTHING MAYTAG!!!

Brand new washing machine model MHW8200FW purchased at Karls, a Ferguson subsidiary, in Madison, NJ end of June, 2017. I wanted to buy a top of the line machine and this is what the sales person recommended to me. Problems started soon after purchase. Initially I contacted Maytag because the machine wouldnt spin dry a cotton bath mat weighing 4.5lbs soaking wet. I was told I should put more items in the machine to help balance it. Well there WERE more items and the machine wouldnt spin dry them either. I tried every trouble shooting Maytag suggested. Having exhausted my nerves, I called for service. The technician came and said these machines are extremely sensitive and that sometimes they wont even run an empty cycle. He said this is a common complaint with these units. One of his suggestions was to take bath mats, duvets, comforters... articles like that to a laundromat.I did less than 10 wash cycles after his visit when the washer started having more issues and finally broke down completely. The technician who came this time wrote a repair order indicating a mechanical (Stator) AND electrical (Control Panel) breakdown ($500+ for the parts alone if the unit wasnt under warranty). He also stated that he had never seen such problems in a brand new machine.I contacted Maytag for an exchange. Maytag customer service wrote to me that the breakdowns are ... normal, with all the units we sell some may have a defect in the first couple of months... and refused to exchange my defective unit. I can accept that there may be a defect that will warrant a repair, but in this case there are multiple defects in separate systems - mechanical and electrical - within the first month of service. This shouldnt warrant any further discussion, only a quick replacement and an apology.

My double oven was purchased over 6 years ago. They have been served yearly and work fine. The only thing is the cleaning cycle which if used at the high temperature to clean can affect the oven temperature control. I don’t use this function anymore.

Ive had my Maytag microwave (MMV4203DS00) for a little over two years. I started getting SE error code. The control touch pad membrane is shorted out. I suspect because the design doesnt allow it to be an over-the-range even though thats the kind of microwave it is! I think the humidity from the burners shorted out the membrane. I called the company and the part would cost approximately $180 for me to fix myself. I have a really hard time believing that one part of a $200 microwave costs $180. Ridiculous. It appears this microwave is designed to fail. Customer service was rude and snarky. The company doesnt appear to stand behind their product. Maytag used to mean something. I had started to replace all my kitchen appliances - microwave, then stove. I thought Id be consistent and buy Maytag based on their reputation. I will never buy Maytag again.

Maytag Dryer- Bravos XL - Waiting for my third service call since purchasing my dryer less than 2 months ago. After 2 service calls the repairman found a piece of the mold that should have been removed at the factory causing problems. Now, my dryer made a weird noise, sparks flew and it no longer works. After calling the seller and the manufacturer requesting a replacement, they feel it should be repaired (again).

When we turn up the temp in the oven above 400 degrees, noxious fumes come out giving us headaches and nausea. We have to open all the doors and windows and bring extra fans...very toxic. PLUS the vent for the oven is at the top of the oven door, so the knobs for the burners get so hot you cant touch them!

I bought a Maytag washer and dryer about 2 years ago. I’m on my second washing machine (one was replaced from Lowe’s not Maytag). The second washer has now gone out! First it was the lid lock and now who knows! The repairman can’t even fix it. Biggest piece of crap, stay clear!! My first set lasted 25 years. Poor quality workmanship and customer service!!

We purchased our Maytag washer about four years ago. I love the features, but occasionally we have clothes rip in the machine. We have had it serviced only once for maintenance. It is great with the large capacity. I can wash bedding including quilts and sheets in one wash. Makes laundry day a breeze for a large family!

A washer should last 10 years. Bought it in 2009 - after two years we spent $200+ on seal and bearings. Now, in 2014 we need more seal and bearings and the service tech recommended by Maytag says the cost will be $500+. Machine has a serious design flaw, and bad parts, and bad service.

Replaced a Maytag Bravos xl washer and dryer in 2015. First year was fine but almost right after the warranty period, the spinning cycle was loud. You cant even have a conversation near the washer. I put up with it after calling the repair department. Because I was told that it will cost as much to repair than buy a new washer. Now the washer does not drain when a small amount of cloth are in the washer. Dont buy this washer and dryer. Maytag is not as good as it once claim.

Quiet, efficient and leave you with clean dishes & utensils at the end of its multicycle cycle. This unit can self-clean and is always beautiful with its shine finish stainless steel interior. This unit can be installed by any user as it comes with everything one will need to complete the installation.

Like many others, my Maytag Bravo motherboard has stopped working after about 2 years. The clothes do not get particularly clean, it is extremely noisy, and the wash cycles are excessively long. I would not recommend this appliance to anyone.

This is the second Maytag appliance in less than 5 years to stop working. The first was a dishwasher. I got 14 months use out of before the control panel burned out. Fixed it for $125 only to have it happen again in 6 months and repair company said parts are only 3 months warranty. Cost me $5 to bring to landfill. Now the matching Refrigerator is making a loud humming noise and Ive been told its the compressor.

Maytag Frontload washer MHWE300VW12 - I bought the washer and dryer in 2010 through Lowes. In Dec. 2012, it started making a loud sound when it would be in spin cycle. I called for service. When the repairman came out, he said the rear seal/bearing was bad and has gone out. The part and labor cost would be $1,184.36. Come on, are you flipping kidding me? Thats twice what I paid new for the washer. I bought them for the Maytag name. If I would have known it was a Whirlpool, no way I would have gotten them. My mother had a Maytag set that lasted 30 years. That explains why they dont show the commercials with the Maytag repairman that wouldnt have anything to do. Also, when the parts came in, they were Whirlpool parts. What a scam. Just more junk for our landfills.

I made the mistake of buying the stainless steel bottom freezer (model# MBL2258XES1) approximately 1 year before the freezer started to make a periodic clunking sound. The repairman responded because my year warranty was still active and found no cause for the noise. Fast forward a couple of months later and it started pouring water out onto my hardwood floors!!! Unfortunately it happened while we were away and my floors were destroyed. Maytag wants nothing to do with me. Im so disgusted. I now have to have a towel permanently on my kitchen floor. Nice. I made the unfortunate mistake of buying an Amana dishwasher recently not knowing that they were also owned by Maytag. The dishwasher is a water waster :( This is very disappointing - you try and buy American and you get screwed. If any lawsuits start up, sign me up!!!

Please save your money and do not purchase a the Bravos XL MCT Washer and Dryer! I am sickened by the fact that I spent $1,800 on the biggest pieces of junk there ever was. Youd think a company like Maytag would be able to build a product that worked properly. We are getting ready for our FIFTH visit by a service repair company that will only plug in their computers and say nothing is wrong. Well here is what is wrong: Washer does not rinse all of the soap and I have many, MANY, pieces of dark clothing that are ruined because of the white streaks all over. I have done EVERYTHING the service guys have said to do; use less soap; use the deep water wash cycle, etc. etc. There are only two of us in the household so my average load size fills the EXTRA LARGE drum maybe half full so all their advice hasnt worked. It does not rinse the water out of a load of towels (remember there are only two us so not that many towels) and I have to run it through a rinse and spin cycle. Waste of time, energy, AND money. I washed a single coverlet and had to run it through a rinse and spin cycle twice to get the water out! If you use the bedding cycle, it runs for 90 minutes and still doesnt spin all the water out! The dryer is not better either. On average, it takes one hour and ten minutes to dry 3 bath towels, a couple of hand towels and a wash cloth. One of the service people that came out, checked our dryer vent and said everything was hooked up correctly. Talk about a waste of energy!! I would do anything to get rid of these pieces of junk but we spent so much money on them Im stuck until I win the lotto or something! I cannot stress enough that you will be wasting your money if you buy any washer and/or dryer product from Maytag! Believe me, I regret it every day!

Purchased this unit back in November 2011. Sometime this year it started leaking water just like many others from the freezer unit onto the floor (many times large puddles). Im tired of the permanent towel on the floor to absorb the water to prevent a potential slipping hazard. I too went online and found a very nice video on youtube which showed how to disassemble the freezer compartment. Took everything apart and noticed that there was water frozen on the supply line. Melted this and put everything back together, for about a week there was no water leaking so I figured all was well. About a week later the puddle was back so I sent an inquiry to Maytag and let them know I had an image of the issue and asked if it was covered through manufacture warranty. Here is their response: Your email is extremely important to us here at the Customer experience Center and we sincerely apologize for any delays in responding to your email. We are working diligently to respond over the telephone and through email to all of our customers. We are sorry to learn of the problem you are experiencing with water leaking from the bottom of the freezer. Unfortunately, we are unable to determine from this location the exact cause of the problem. We recommend that you contact a certified technician for an accurate diagnosis. Once the problem has been diagnosed, please contact us back so that we can review the concern further to determine if assistance is available. For your convenience, we have provided below service providers in your area that you may contact for service. Aries Appliance Service (925)367-7708, Vigil Appliance Service (925)371-7701. You are a valued customer and we do apologize for any inconvenience this concern has caused. We invite you to contact Maytag again either by calling (800) 344-1274 between 8:00am to 8:00pm EST weekdays or by emailing whenever the need arises. When calling please press the available option or stay on the line to reach a representative.Frustrated I went online and found this forum where hundreds of other people had the same issue and that many of them were resolved by the new P Trap. So I watched another video by the same guy on youtube that showed how to replace the P Trap. I went online and found the replacement P Trap Manufacturer model # w10619951. One of the comments there actually said to call Maytag first as they were able to get a replacement P Trap for free. I believe if it was under a year old they would also pay for the labor to have it replaced. So this morning I called Maytag, the first guy Jim said I would have to have a certified Tech come out (76 dollar service fee, plus whatever the labor would cost) and Maytag would cover the cost of the part. I asked Jim if he could just send me the part and Ill do it myself, he reassured me that he could NOT do this and that the system was very specific. I told him I did not understand that a bad design and known quality defect, why should I have to pay several hundred dollars to fix? He told me that was the way it is. I asked to speak to his supervisor and put me on hold. Not only was the hold music extremely obnoxious but there was a loud humming noise as well, I waited for 10 minutes hung up and called back. I spoke with Maggie this time. I told her I wanted the part sent to me and if she couldnt help me I wanted to speak to a manager. She said she did not have the authority to ship me the part without approval. She said she could ask for approval and after waiting for about 3 minutes she came back on the line and said she spoke with her supervisor and that they would be sending me the replacement P trap today via FedEx. Had they not sent me the part my next stop was going to be the better business bureau..

Wish I had read the reviews! I have had Maytag before and they were awesome. New purchase is horrible! Doesnt clean the clothes, leaves a residue on clothing and dryer does not dry properly. Called Maytag and they said use Affresh. Spent $10 on a pack of 5, and it did no good. My dark clothing is getting ruined! The washer is also incredibly LOUD! Very disappointed in this company and would never recommend them to anyone! I had purchased at Lowes, but had a delayed delivery, so I cant take them back, or I would.

I bought a Maytag dishwasher to match other appliances in kitchen. Work great, not loud and gets dishes clean. Have owned it for 10 years and have one problem with the door latch. But it was easy and inexpensive to replace.

I wish I had read the reviews before selecting this Bravos XL washing machine. I bought these from Conns Appliance as they were on sale 750. Rounded figure... They were delivered today and the company was professional and set them up, I have spent the last 4 hours washing the same medium load of childrens clothes trying to get them clean. Ive even separated them into smaller loads and am now into the 5th hour of laundering this same load... Im returning them but its gonna cost me 15% restocking fee. If theres a class action please count me in. I thought because our Maytag Neptune lasted so long wed have a great outcome again with these, boy were we WRONG!

Purchased this dishwasher 3 1/2 yrs. ago. Control panel went out. We would have had to pay almost the cost of new one to replace the part! Maytag used to be reliable. The dishwasher we owned previously (not Maytag) was still working after 12 years!

I bought a fridge, model number MBF1958, its a top fridge-bottom freezer. The freezer part leaked and spilled water that then froze onto the bottom of the freezer, which of course froze. I discovered this 1 month after the 1 year warranty ended. Maytag gave me a courtesy repair service guaranteed for 90 days. Of course, 2 weeks after the 90-day period ended, I have the same problem again.

It’s a front loader, very quiet, and uses less water. The clothes come out clean and less wrinkled if you take advantage of the settings. l like the extra rinse and the drawer underneath. The capacity is able to accommodate enough clothes so I only need to do a load of darks and a load of whites each week.

I bought a new Maytag Quiet Series 300 in 2005 and have had nothing but problems with it. The internal plastic pieces that hold dishes in place have broken off regularly. The door handle also broke. The dishwasher does not drain all the way every time. Now, the dishwasher will quit randomly before finishing its cycle. Our model (MDB7600 AWB) was not part of the recall, but is a lemon nonetheless. Of course, all of this occurred after our one year warranty had expired. This dishwasher is a lemon and a waste of $400. Well never buy another Maytag product.

We purchased a high-end stainless steel interior/exterior unit in January 15. It is now July 15 and we have not been able to get any use out of it. Day 1 washer leaked. Full day off for service. Guy told us we were using the wrong soap. It leaked on the very next wash. Called again. They forgot to check the soap dispenser. Another service/day off. Leaked again! Another service call/day off. They replace the dispenser & seal. Now washer no longer leaks but the dishes are dirty and wet even days later. Another service call. Another new part. And now we are waiting for our 5th service call. We paid for a new unit and have a refurbished cobbled together piece of junk. Maytag stubbornly refuse to replace this unit.

Weve had our Maytag dishwasher for less than 4 years when the control panel quit. The repairman came today. He was here 10 minutes and it cost us half as much as a new dishwasher. Its just the two of us and we use the dishwasher once every 4-5 days. Almost laughed when the repairman said the part and labor was under warranty for 90 days! There is no quality control anymore. Just greed.

We had a Maytag washer and dryer for over 32 years, the same washer and dryer. Finally our washer failed. We thought it would be a good idea to stick with Maytag. My husband purchased the Bravos XL Maytag washing machine. It is the worst washing machine ever and I regret the purchase. The washing machine doesnt clean clothes. If you use a powdered soap of any kind it leaves residue all over your clothes due to the fact it doesnt use enough water. It binds everything up. It becomes unbalanced with any larger load. Completely ties your sheets and your pants into knots. Yes literally I pull my clothes out and they are in a knot. The washer started to leak about two months ago after having it for a year-and-a-half. We couldnt locate the leak so we had to call a repairman and it cost us over $240 in parts and labor.

We bought a Maytag dishwasher on 9/22/2012. Model number MDB7759SAB. Within the past couple of months, it has been very temperamental. The control panel started beeping continuously and some of the functions wouldnt work anymore while others continued to work too well; in that the dishwasher on occasion would rewash several times without anyone starting the machine again. The dishwasher also started leaking water... As of yesterday, the dishwasher control panel stopped responding and then out of the blue, the dishwasher turned itself on in the middle of the night! We called customer service and they said they could send a repairman out for around $89 and then we would have to pay for the parts needed and the cost of labor. After reading many reviews sounding exactly the same as mine, my husband and I are against repairing this lousy machine. Its absolutely ridiculous for a dishwasher to quit unexpectedly like this. Our question now is, which brand to purchase for our next dishwasher? No more junk please!!

The Maytag Bravos XL washing machine has a difficult time getting clothes clean. The glass top allows a person to watch the clothing being washed. After one watches this for 5 minutes, it is quite clear that the clothes are not being washed properly. Clothes frequently end up dirty at the end of the wash cycles. I personally believe the design of the agitator is so poor that it is not capable of moving the clothing around to come clean. The tub is a large 4.5 cubic foot capacity, but because it uses so little water it simply doesnt function as advertised. Often there is residue on clothing, simple stains like dirt marks dont get removed. In addition to poor cleaning, the spin cycle is simply bizarre; clothes are twisted to the point that the wrinkles created during this cycle will not come out during the dryer phase of laundry work. I am completely unsatisfied with my purchase and regret not researching this more prior to purchase. I am baffled that this product could actually make it through quality control at Maytag. I have had one service call under warranty to fix the lid not locking. This repair was completed with satisfaction.

The washer is making loud noises. I had a repairman out and he said the transmission was shot. This washer is only 7.5 years old and the set I had before lasted 19 years. It also was a Maytag. My mother, sisters and aunts have always stood by Maytags and I am disappointed that this washer being 7.5 years old is shot. The dryer to the set is working great!

First we design the cheapest, flimsiest drawer possible on the bottom of the stove. Then we mount it on cheap plastic guides on a flimsy metal track. What a joke! Listen, drawers have been around over 700 years. If you cant do better than that, you need to look for another line of work.