We purchased the HE commercial brand for our family of 7. It has been running mostly fine for about 2 1/2 years. It started making a horrible grinding noise about 3 months ago. It was getting worse and worse. I decided to google the issue and discovered there was a common problem with a nut falling off the bottom. I leaned the washer back and found the nut on the floor, right below the center of the pulley. I reattached it by removing the pulley guard which had been getting cut by the loose and wobbly pulley, put some superglue on the nut and reattached it to the bottom. NO MORE NOISE!! Im willing to bet that this has caused slippage of the pulley, poor performance and many other issues. Maytag should do something about it.

We purchased our Maytag Bravos washer and dryer in 2008. Within a year, the hinges that held the door open on the top load washer broke. In year 2, the area around the fabric softener dispenser rusted so badly that it almost completely ate the porcelain enamel away. In year 4, it started making a noise that I will compare to a jet on takeoff during the rinse cycles. It continued to work but got louder and louder. We looked into the cost of the repair, which was going to be $350 parts + labor. If it had been a good machine, we might have considered fixing it but it wasnt. Even a set of sheets could put it off balance, which stopped the machine with the wash cycle incomplete. It also set its own water level based on the weight of the clothes and many times the top items came out with dry spots that hadnt even been submerged throughout the whole cycle. Consequently, the clothes were never very clean and I would have to rewash many loads. This machine was not cheap - around $1,000. I was so frustrated and felt completely taken by the Whirlpool company again. We have had many unhappy situations with their products over the years - Kitchenaid, Jenn-Air and Maytag. We finally learned our lesson and researched washers online. The best rated that we could find was Speed Queen. We couldnt find it in Canada, so my husband drove 5 hours round trip to the US and bought one. We have had it 4 months now and the difference is unbelievable. Our clothes are clean again. I can set my own water level and the hot cycle actually gives you hot water. It never goes off balance no matter how many or few clothes it has. If I see that I need more water part way through a cycle, it has a button that lets you add some part way through. It doesnt have a lot of bells and whistles. Its a basic but excellent machine that is a pleasure to use. I would recommend it highly. I realize it has only been a short time, but my Maytag never performed like this machine even from day one. It reminds me of my very first washing machine many years ago, an Inglis, which never had a repair in 15 years of use. If our dryer goes, we will definitely buy Speed Queen. The trip is well worth it.

I built a new home in November of 2013 and filled my house with all brand new top of the line Maytag appliances. Almost a year and a half in, my $2500 refrigerator is broken and all my food is lost. They send a repair man out; and guess what, the warranty is expired. So they wanted me to pay $800+ to have my refrigerator repaired a year and a half after I purchased it. I cant believe they have no shame in sending out products with their name on it that only last 1 1/2 years! I would never treat anyone like they treat their customers. They hold no responsibility. Their name holds no value to me anymore. I was extremely disappointed.

We purchased this washer 3/25/15 for $873.77, we also got the matching dryer, for the same amount. This washer, never washed good, it is simply a bad design, I dont know, what type of mind altering products the designer was on at the time, but it must of been some good stuff, since all brands jumped on the wagon. This is a POS, I have contacted Maytag, and they just ignore me. We need a class action lawsuit against them, they think they can take our money, and laugh at us.

Bought a Maytag bottom door refrigerator/freezer about 3 years ago and within 6 months had the bottom drawer ice freeze issue that is so common all over the internet. Today is the THIRD ** time Ive had to take this piece of crap product apart and clear the ice. For all of you who have contacted Maytag in the past... Ill bet you got the same response I did when the fridge was new. They claim there are NO KNOWN ISSUES. They actually told me they had NO RECORD of previous complaints with this issue. MAYTAG SUCKS! I wouldnt take a free appliance from them. Worst customer service possible and they take no responsibility for their ** design and problems. There should be a class action suit for this issue. IF ANYONE IS EVEN CONSIDERING A MAYTAG APPLIANCE... Do yourself a favor and think twice.

We bought our Legacy Washer and Dryer from Home Depot in December, 2005. Luckily we also bought the one year warranty, because in January 2006, our washer quit running. We called Home Depot, we got the runaround and I think Maytag sent someone out. When he tipped the washing machine over, a belt was off. He said it happens. The next year, something else went wrong with the washing machine (not under warranty anymore) and I paid $129 for that visit. Three weeks ago, the spin dry quit doing a good job on the extended spin cycle. Tonight, I put a load of clothes in and though the washer sounded like it was agitating the clothes, when I lifted the top I saw it was just noise, no agitating. I cannot afford the service call, let alone the whole repair or a new washer.

I bought a top end Maytag refrigerator with the freezer in the bottom drawer. Spending the extra buck was something that I thought was worth it, being a Maytag. Fifteen yrs go by and it stops completely. It cost me 200 bucks for a service technician to tell me that the compressor or it has a leak. Its not worth repairing. With todays cience and technology, you would think that they can make a refrigerator last for 25 yrs or more, like the old ones. We went to the moon 44 yrs ago. Why cant they make them to last? I think that the corporations figured they can make more money making an inferior product that needs to be replaced every 10-15 yrs. I will never by a Maytag again.

Model# MVWB850WQ0, Serial# CY4070329, Type 580-02. Bought this Commercial Technology washer 2-1/2 years ago thinking the commercial model would be heavy duty. It was only heavy on the wallet. The washer started to emit a loud roaring sound two weeks ago that never happened before. It happens on spin cycle. We cant even have a normal conversation in the house. After reading similar problems and outrageous cost to repair, Im leaning to look for a replacement without the Maytag label. My 10+ year old Sears Kenmore didnt have any problems. My mistake was to replace it with a more efficient washer. I guess New+Efficient doesnt equal long lasting for Maytag. You would think a major manufacturer would put in heavy duty bearings in a washing machine. Heck, maybe the bearings are heavy duty but design shortens bearing life. Enough time spent on Maytag. Stay away!

You can not add water to the fill, blankets dont even get wet when you wash them, you can do double rinse but cant control the fill, have to sit there and lift the lid up and down for 20 minutes to get enough water in the machine! The washing machines have turned into absolute garbage! Wish I would have come here first, whats the difference if I control the load size water or IF I SELECT DOUBLE RINSE? THIS WASHER 200% GUARANTEED I WILL NEVER BUY A MAYTAG AGAIN. ABSOLUTE TRASH FOR $700.

Maytag Dryer MED6000XR2 - Purchased in Sept. 2012 - first service call 1/13/14; 2nd service call 2/20/2015 and less than one month on 3/14/15 it goes out again. It takes one week to get service company out and then another week for the part to be ordered and put in. This means I am without a dryer for over 2 weeks. An $1,100 dryer goes out every year and sometimes within one month?! According to the service company, it just is the way this dryer works. Really? If Maytag ever wants my business again, I better get a more justified reason and better than 2 weeks service call. This is absolutely ridiculous.

My grandmother got a Maytag Bravos XL MVWB755 washer and from day 1 she had to call Maytag with issues due to residue left on the clothes. They told her to not use this setting... buy this detergent... only use cold water etc. Never did they offer a repair guy to come out. A year passes still having issues shes out of warranty. They now offer a repair guy but claim theyre going to charge her $90. Once she explains to them that she was never offered a repair guy & they shouldve done this before. They decided to waive this fee and send a repair guy. Once the technician comes out to the house they do absolutely nothing and they fill it up with water say we need to clean it and Ill come back out and do another diagnostic. When they come back all they do is fill it up with water get a glass check the water and say, Nope, no floating residue. Everythings fine. They then tell her she needs to get a water softener which is going to be hundreds of dollars.The technician also says do not use any other settings except for these two. Can someone please explain to me why they have all these dang buttons and settings if were not supposed to be using any of them and why all of the clothes come out with soap residue scummy residue all over them? The old washer never did this. It was a Kenmore and its the same water same everything but this Maytag washer is been nothing but problems. It leaves the residue which is stripped all over dark and white clothes, it is extremely loud, not all the clothes even get wet! Maytag is been extremely uncooperative with assisting my Nana. They tell her no one else not one other person is having this problem but when I look up this issue I find that about 2500 people on this forum are having very similar problems. Something has to be done. Maytag should have to take responsibility for this washer. The bottom line is it supposed to be an XL. When my grandparents are washing its only for two people. Theyre not even filling that washer up of all of the clothes are not even getting wet. It just goes to show you that the energy-efficiency that they claim is not working. The washers not getting enough water inside of it. Its not fully rinsing the clothes and no one should have to put the clothes in wash them then do a whole another rinse cycle just to get the dang soap off. So basically at this point she stuck having to do multiple washes using way more utilities than she should have to and Maytag is basically going to do nothing. It wont help her over the phone the technician is a joke and it looks like so many of you people are having the same issues.

I bought the Washer and Dryer. All I can say about this washer is that it does not use water enough to be considered a commercial type of washer. Its balance is poor also for being so deep. I have to pour a bit of water on the clothes so the sensor thinks it’s a heavy load and do an extra rinse. And I saw that on a video regarding this washer trick. But I’m wasting more water cause I have to rearrange the clothes when done. I put the top ones on the bottom and start over. To me it’s a waste of effort sometimes I just go to the laundromat. They should consider their products if we all are complaining about this they should really do something. To me the washer is really useless.

We purchased a Maytag 4.2-cu ft High Efficiency Top Load Washer from Lowes. The pump went out within 6 weeks of purchase. Maytag could not get a technician to come to our area to fix the washer. They finally told me they would give me $150.00 for labor if I found someone to fix it. We ended up taking it to a Maytag certified repair shop. It cost us a $99.00 service fee. They ordered a new pump from Maytag, part cost 137.46. I called to get a reimbursement from Maytag and they denied my claim. Their reason I was told was because I didnt call the part in myself. I dont understand why they didnt even reimburse the $99.00. The washer was a lemon and Maytag did not honor their offer, nor the warranty. Very time consuming and bad experience.

We purchased our Maytag dishwasher from Nebraska Furniture Mart in February 2013. The touch panel on our Maytag dishwasher quit working in December 2014, several lights would come on or flash or not work at all. The first repairman that we had come out took the panel apart, cleaned it up and put it back together ($100). It started working again but a few days later it started doing the same thing again. So I called the repairman back and he said the touch panel would need to be replaced. He called all over Omaha and no one had the part in stock. He called the Chicago Maytag warehouse and was told by them that they were out of them because there were so many defective dishwashers that they used them all. Now they are trying to find a new manufacturer to make them. It could be months before they get them in. So I contacted Maytag and of course they said that is not true and put me through to a parts company that they said has all the parts available. When I told that company that it was the touch panel, I was told by them that you only replace the touch panel for cosmetic reasons! So we got a second opinion from another Maytag repair company and he spent about 10 minutes looking at the dishwasher and said its a defective touch panel. He said he has replaced a lot of them in Maytag dishwashers. He recommended that I contact Maytag customer service and try to get them to pay for the part. I did call them and of course they refused because it is out of warranty. The supervisor even told me that they have not had any complaints about the touchpad malfunctioning! They do not stand behind their products anymore. I will never buy a Maytag or Whirlpool product ever again. I told them exactly how I felt and their only reply was Im sorry you feel that way. I am surprised they continue to stay in business. I dont understand how major stores can continue to sell their products when they are garbage. Based on the other reviews Ive read, Im not even sure we should fix this for $250.

Maytag Bravos Automatic Washer 300 - I purchased this washer on July 29, 2010 from HH Gregg. It is less than 3 years old. The washer stopped mid-cycle, did not drain, and displayed the code Ld. The service company recommended by Maytag said that the control panel is defective, and the cost to repair/replace it is over $550 and isnt worth fixing since, he says, these washers are notorious for having problems. Maytag is unwilling to recall this washer despite all of the problems that have been reported. They are unwilling to even admit there is a problem.

I bought a Maytag 4452BDW stove, the more button is not working. I did my research and was not happy to see this is a common and reoccurring issue with Maytag Stoves. The expensive of the part that too often fails again along with the cost of the service man to repair it places the Maytag as low quality at a high price. I am hoping to see a company that stands behind its product by addressing this correctly and promptly. It would be a pleasure to have my faith restored as it should be by Maytag.

I have had to put two 50 lbs sacks of feed on top of my Maytag Neptune Washer to keep it from walking in my washroom. Looks like I am not the only one with this problem.

Wish it was a French door style instead of freezer on top. Not good if you are tall. Other than that we are pleased with it but will look to trade for a French door style.

Fridge model mff2055drm00 - Purchased 2 years ago. Upon delivery and working water leaked from bottom. Called recommended service. Result took out fridge and brought in another new one. Today the fridge/freezer ices up, ends up sounding like a rocket ship. Not working efficiently. Called for authorized service. Was told needed a new thermostat... after TWO Years? Service call price $125, quote to purchase, replace and install thermostat $550. Almost $700. Big mistake buying Maytag- who knew? But never again! We are quite angry and very disappointed with the mediocre performance of this product.

I purchased a washer and dryer model MAH8700AWW. In 2005, I purchased the extended warranty. In 2009, I had to replace the main control board and motor on the dryer. Now, I find out that the washer has a warped drum which caught on the door boot and messed the shaft up. I didnt know that it has probably been that way since I purchased it because every time I washed clothed, I had to stay in with it because when it would go to spin, the washer would walk out into the middle of the room. I called about it and they told me to put rubber pieces to hold it still. Now it is going to cost $ 821.95 to fix. That is more than I paid for the washing machine and Maytag will not help to fix it. I would like someone to contact the company and find out why they dont stand behind their products anymore.

Just got a Bravos Maytag commercial washer. Washed two throw blankets and the washer has a see-through window on top, and I could see that the blankets didnt move on top. How are clothes supposed to get clean if they dont move? It also took an hour and a half for one load. What you are saving on water you are wasting on electricity. I personally dont like them for those reasons. I appreciate the company in my town (little known), they let me return and get the old agitator type with NO sensors. Just love the agitator, might wear on clothes a little more but at least I know theyre clean!

This is my second washer in less than 5 years, going third. No customer satisfaction. Maytag/Whirlpool dont care, Customer Service doesnt care - all I hear when I call is, “too bad”, “so sad”, “call a repairman”, so you can spend another $100.00 plus. I hope this doesnt happen with someone elses brand when we buy it. Shame on such a big company.

I got a Maytag Bravos 18 months ago and liked it at first. After using the washer for a while my towels were falling apart. Did not connect to the washer at first but I began to notice pulled threads on my towels. Talked to Maytag customer service who said they had never heard of the problem. She did say mix the towels with other clothes to prevent the problem. When I got this machine we had about two dozen good quality towels. Now I am down to maybe a half dozen. Those came from the six my Dad bought us for Christmas and I stashed away. The towels have pulled threads all over and will be completely destroyed soon.

The washer 4 years ago we had the control panel replaced at our expense. Now, control panel is going out again. Also this summer I took the dryer apart to snug up some screws that had come lose, that were scraping the inside as the dry ran. I own a range and a dishwasher Maytag brand but will not buy another Maytag unit, even if they are built by my union brothers and sisters.

Bought a Maytag top loader washer from Lowes in July 2017. Have had nothing but problems due to faulty computerized guts. Worked intermittently and took a long time to wash compared to older machine. Repairman out twice... replaced computer board and still have problems. The machine was made in Canada according to the label. Hey Canada, what is going on making junk? Too bad that we did not know beforehand what junk the Maytag brand has become. Lowes should not sell this junk to help its reputation and valued customers.

I bought the Maytag Centennial Washer a year ago. I have had nothing but problems. The clothes never get fully wet so you have to wash clothes 2 or 3 times. The lid does not open when running. So you cant put soap after the clothes are damp. I say damp because they dont get wet. Right now the sensing light has been on for 2 hours. I need to catch a flight in the morning and I cannot wash my clothes! My white clothes never get clean. I have to wash 2 or 3 times. Actually 4 time would work better. The water and electric wasted with washing over and over again is nuts. Stay away. Ive warned you!

The low water usage design is horrible. Clothes dont get clean as it doesnt use enough water to cover them. Takes twice as long to do a load as our old washer. Took about 1 1/4 hours yesterday for 1 load using heavy which is the only setting that uses more than a thimble of water. Should have looked for a commercial type with a real agitator and adequate water usage. Not saying Maytag is probably any worse than any other brand of new efficiency government mandated garbage washer, but its no good.

I called customer service to ask if there was some way that Maytag could assist me with repair of this like new dishwasher. When I said it was out of warranty and I had no additional warranty, I was told that a repairman could come out for $110 and diagnose the problem and that parts and labor would be extra. I explained that I had purchased Maytag because I saw commercials, for years, showing that Maytag repairmen had no work. She was very unhelpful and kept droning the same mantra, that a repairman could come out for the above charge. I was very angry and asked for the name and address of the President of Maytag so I could send a letter of complaint. I composed a letter, however: it is Thanksgiving time and I need my dishwasher so I made an appointment to have it repaired. I was told he would be out Mon. between 8 and 5. I asked for a more specific time and was told that I would get a call on Sat. with the time. Thankfully, no call came, because on Sunday, I read the reviews on this site and realized that Maytag was no longer a reliable nor a responsible company and I decided to save myself money and time and stress and just go out and buy a GE. So we will hand wash the dishes on Thanksgiving and buy a GE on Black Friday. This does not mean that I am letting Maytag off the hook. I intend to send my letter to Jeff Fettig at Maytag and also join in the class action suit. How very sad that the name Maytag has become just a name used to shill for defective and shoddy merchandise.

We have had the same problem as everyone else. We have the freezer on the bottom model. It started when the fridge was less than a year old, with water on the floor and ice buildup on the bottom of the freezer. Since then we have needed to have same repairman come at least 4 times because the top part suddenly gets very warm, food spoils, and water accumulates under the produce drawers. Our repairman has told us that newer models have improved design, but that doesnt help us. This fridge is now about 3 years old, bought it at Home Depot. This is unacceptable.

In September 2008, I purchased a Maytag washing machine (Model MTW5700TQ0) that had a faulty transmission. The machine was immediately replaced. Three years later, the transmission is again faulty. Maytag has refused any responsibility for repair or replacement.

This is not a complaint but a love-letter. I know that todays Maytag Neptune is not the Maytag of old. But Im here to report that Im still using a Maytag washer that was built in 1982! The only thing wrong with my machine is that it occasionally goes off-balance when I wash heavy towels or blankets. Note: We inherited this machine with the purchase of a home in 1991. We were a family of 6, so this machine has done many heavy loads! Im looking forward to celebrating my Maytags 30th birthday, come Jan. 1, 2012. And I would love advice on how to replace it, eventually, with another machine that has just the basics - no bells and whistles, computerized control panels, etc.

I have had this refrigerator for less than 3 years. It recently started leaking water on the floor and all over the bottom of the freezer. Repairman said it is a flaw with the defrost drain design. He thinks Maytag MIGHT have changed it since I purchased mine, but I dont know. Originally they used this small rubber valve;repairman said they get clogged very easily (even though I vacuum around it regularly and dont have any pets). He replaced that part with something sturdy that looks like a p trap. I looked online and there are loads of complaints about this exact issue with the defrost drain clogging. It cost $250 to have it repaired. I called Maytag to ask to be reimbursed and of course they will not do anything since it is out of warranty. Its a shame Maytag wont stand behind their products. Since there are so many of us with this issue, cant something be done?

We bought a Maytag Bravo washer and after less than 6 months of use, it stopped working with an F51 or 53 error (cant remember which because its been a month now). After looking online, it seems that almost everyone who buys this gets this error and has to have a part replaced! And Whirlpool hasnt recalled the faulty part even though everything Ive read says it should be a recall.Its now taken over a month to get a repair person in to fix it. From the time we called Maytag, to the referral to the service person, to the service appointment, to waiting over 2 weeks for the part to come in, its been over a month with no washer. This is unacceptable Maytag! The repair company is finally showing up tomorrow only after 3 left messages from us.Either build a better washer or stock your replacement parts with the local repair companies and you should be reimbursing your customers whove spent a lot of money at the laundromat after spending between $700 and $900 on your washing machines.

I purchased an Atlantis washer in 2005 and assumed that Maytag was still one of the better manufacturers. How naive of me! What genius at Maytag thought it was a good idea to place the water filter inside the washer? Not only can you not keep the filter clean so that cold water will flow properly, even worse, if the filter completely clogs, the water will not stop filling into the tub which could, of course cause an overfill and flood. I narrowly escaped this scenario once. No one should have to stand and watch their machine fill with water to insure it stops. Now the machine is causing a grinding noise when agitating. I expect it to stop working any day. I will not buy another Maytag or Whirlpool, who of course now owns Maytag. And I will not pay another repair bill for the filter or any other part. The brand was once considered the best in America, now its just another brand thats a piece of junk produced in another country.

We purchased a Maytag dishwasher & installed Aug 15 2012. After installation the control panel wasnt working & Lowes replaced the dishwasher with the same model. After the years warranty was up I started having trouble with the second dishwasher panel. I limped along with it for months until I could not get it to work at all. A repairman came and said that the touchpad & board was damaged. He said it wasnt hooked up properly. After an estimate of over three hundred dollars we decided to rid ourselves of it and purchased another, cheaper brand. Was out 79 dollars for the repair estimate & over 500.00 for the Maytag dishwasher. Plus a new one installed for 700.00. Had the use of this appliance less than two years.

On May 11, 2010, I purchased a Maytag washing machine from Lowes. On June 22, 2011, the machine wouldnt empty out on the rinse cycle. Lowes was called as the machine was only one month out of warranty. They dispatched Appliance Plus for a service call which would be $80.00 just to diagnose the problem. It turns out the machine needs three parts - a timer, an ATC switch, and a rinse switch. All totaled, this will add up to over $300.00, plus the $80.00 for the service call.Appliance Plus tried to contact Whirlpool to see if Whirlpool would at least pay for parts, being it was only one month out of warranty. The answer took 5 days and the request was denied. I was told I should contact Lowes Service Advantage and maybe they could contact Whirlpool for a special consideration, again, being it was only one month out of warranty. I made the call and they said to give them two business days turn-around for an answer. On June 30th, Lowes said Whirlpool was looking for the serial number and I provided it. They told me to give them another 2 business days turn-around. On July 3rd, I again called Lowes and they informed me that they still hadnt heard from Whirlpool. Finally, on July 7th, I received a call from Lowes saying Whirlpool denied the request.

My Maytag (MER7662XQ) oven has stopped working after barely 6 months of use. I filed a warranty-repair complaint and reported the error codes shown: F1 (faulty touchpad) and F3 (faulty temp sensor). Although Maytag promptly sent a repairman, he arrived without parts and left within 5 minutes without fixing anything. He said he would order parts. Whenever they were delivered to us, by mail, we should call again to schedule another repair. But he warned he was prohibited from coming out for another 7 days. So far, Ive been without an oven for almost 3 weeks and there has been no action or information. My calls to Maytag produced nothing, except confirmation they show the repair as open since they do not actually distribute parts, and the repairman is with an outside company. A terrible product and a worse service! I would not ever buy another Maytag product and recommend that no one else does either.

We purchased our Maytag Bravos XL last month and within two weeks, we were noticing a BAD odor every time we used the machine. In fact, I just walked back into our house from outside and the entire house smells like old dirty dishwater and the smell is coming from the laundry room! This is a very expensive washing machine and we bought it because we thought that a Maytag would be better than the Whirlpool that just died after many years of repairs and aggravation. After reading these reviews, I wish I had bought a Speed Queen.

2016 model washer. Bought a Maytag in 2016. Replaced in 2020. Problems: Spin cycle extremely noisy, have to close the door to utility room to stay in the house. Leaks a lot during wash cycle. Getting the lock to release takes awhile, sometimes I have to unplug it. Makes a grinding noise at times when starting the spin then.

Its a shame that I bought into the Maytag equals quality and customer service falsehood. Same problem as the others on this site and undoubtedly thousands of other consumers that bought a similar refrigerator freezer combo only to discover puddles in front of the unit and a 1 thick slab of ice under the freezer drawer. I contacted Maytag parts and when I described the issue he transferred me to warranty. The warranty department acknowledged this was a known problem and they would supply the part, no charge for the part but I would have to pay the serviceman to install it. They would not however, send the part to me to install. The unit is out of warranty, of course it develop the problem until right after the warranty expired. I plan to examine the drip pan and figure out how to improve on the design myself. I will not replace any appliances with Maytag, Whirlpool, Kenmore, or any other major appliances from this group of companies... Beware!

I purchased a Maytag Washer and Dryer about 3 years ago, they were under warranty for two years. Two years and 10 later the dryer breaks down, repair 310.00, two months later the washer breaks down again, 331.00, while I’m waiting for repair appointment the dryer breaks down, 130.00. Then I’m finally able to do laundry, turn on the washer for the first time since paying 331.00 and IT DOESNT WORK AGAIN, another SEVICE CALL!!! $$$ IM EXTREMELY DISAPPOINTED IN MAYTAG, ESPECIALLY AFTER VIEWING YOUR COMMERCIALS!!!

Front load washer unit does not respond to control inputs. I have called Maytag service and support. One can find a repair or maintenance manual. Im in a smaller market so there is limited service. Maytag service and online support is terrible. Maytag stores are fronts for independent service companies. Its probably okay, but misleading. Everyone wants to order the main controller board. It would be good to have a maintenance manual.

I purchased my 2nd Maytag Neptune washer in 2005 to replace an early Neptune that was complete junk. This one worked OK until this year when it began to make awful noises. After research, I decided it was the bearings that failed. I took the unit apart to get to the bearings and found out the entire outer tub must be replaced not just the bearings, at a cost of $515. What lousy engineering, the bearings dont come out of the housing. No wonder Maytag repairmen are so bored. There is nothing to fix, you just buy a new washer. I wont buy Maytag this time.

Three-year-old top load Bravos. Started doing the LD/SD tango about one year ago. Intermittent fault, but becoming more prevalent. Can spend an entire day attempting to finish one load; sometimes must be unplugged overnight to clear faults. Washer receives heavy use from extended family of five adults and two children but has never been overloaded. Machine is horribly flimsy and constructed of the cheapest possible materials. I wish I had removed the back prior to purchase.Just because it is possible to attach a processor to a piece of equipment doesnt mean its necessarily a great idea. Any geek can tell you that the three things most despised by a digital device are heat, humidity, and vibration. A washing machine by definition is an epicenter, a breeding ground, for those specific environmental factors. Well done, Maytag. You have demolished what was, perhaps, the most respected name in the business. Good luck getting that particular rep back. Purchasing a Speed Queen. The living embodiment of old-school. Electro-mechanical timer. Stainless. Porcelain-enamel. American-made. Not one complained on this site. Might just shoot an Office Space vid centered on the demise of the Bravos. This time, its personal.

We purchased a Maytag Dishwasher in 2011. In 2014 I got no response from the control panel when trying to start the machine. Service came out and had to replace the control panel. The cost for that repair was $269.00. It has now just stopped working again. Same issue. After seeing all the posts, I realize that this is a prevalent issue and in some cases a safety concern. If Maytag knows about this issue with their control panels why have they not recalled or corrected these problems! Needless to say, I will never trust this company again!!! Model number MDB7749AWM2.

I could care less if Maytag responds as I have already advised all my family and friends to avoid Maytag products. After spending over $1200 to buy this refrigerator it took 6 months for the ice maker to failed, and it needed a control board replaced. Maytag had a great reputation; however, in the past 5 years their products are worthless. I also have a Maytag dishwasher which failed and was stuck on cancel with a flashing light. The dishwasher panel needs to be replaced and I have just decided to replace both of these products with a different brand.

Should have researched before purchasing our Maytag Bravos MCT washer! We purchased it at Home Depot and it was delivered and installed by a certified technician. From day one it has been so loud and obnoxious with the way it “knocks” and “clicks” when it runs through a cycle. When it spins the whole machine shakes viciously, despite being balanced properly at installation.We have owned this washer just short of two years and for the last 8 months we have had to keep unplugging it to reset it so that it will even run through one cycle. The most recent two months have been extremely frustrating, due to the fact that not even troubleshooting can aid in “fixing” the fact that this piece of crap washer will not complete a wash cycle! It either stays in sensing mode & doesn’t add water, or it adds water but doesn’t do anything but sit still for about 15 minutes and then drains all the water back out and stays stuck on “wash”. We are researching online and have found many similar complaints with the same negative experiences. Our next step will be to call a repair person! What a crock!!! Maytag gets a big “thumbs down” from us!!!!

Two in a row make it just over a year then the control panel goes out. You call a Maytag repairman and they say the control panel is bad! #1 it should last more than a year and a half. #2 a part shouldnt cost you as much as the darn dishwasher! Do not recommend nor would I ever buy another Maytag.

Our Maytag Bravos is 4 years old. Settings are preset at the factory. Besides the glitches others have written, the hot water sensor INSIDE the machine has gone out. This means - no clothes can be washed on the hot setting, and the warm setting gives only lukewarm water. I have had more than one plumber look at the machine, and the consensus is...the internal sensor needs replacement. However, this machine being only 48 months old, I am debating whether or not just to buy a new machine. This is a HE washer, and I am very disappointed in its performance. This is the worst Maytag machine I have ever owned.

I purchased a Maytag Washer Model MVWB765FW in April 2017. Its transmission has failed, makes lot of noise. The cost to repair is about $500. for Parts and Labor, under the 10 year Limited Warranty, as advised by Factory Service. I am better off buying a new Washer for that cost. The days of Maytag reliability are gone. I would not recommend this product to anybody.

Maytag is the worst dryer ever purchased. We bought it in 2019 and the heating element broke. When I contacted Maytag directly, they said, nothing they could do. Really?? A major part was defected and there was nothing they could do! Its very sad when a major company that you purchased from shuts you down with a defected piece in their dryer and they chose not to help out the consumer. Shameful! I will NEVER purchase another product from them again...

I would like to say that I am highly dissatisfied with paying $1200 for a refrigerator that only can produce ice once every 12 hours and 90% of the time the over fill lever gets stuck so it will not make more. I would recommend anyone to not buy anything Maytag ever.

I bought a Maytag dishwasher in Sept. 2013. This dishwasher looks great, but it leaves glasses stained with a cloudy haze. It also does NOT dry, even on jet steam dry mode. Bottom line, after a little research, I was the one who bought it, so I took accountability and just rolled with it. Well, the control panel stopped working this week (wont light up). I called maytag and the lady told me they would cover a service call and parts even though its not under warranty. When the service company called me, they said maytag will NOT cover cost, totally contradicting what the Maytag lady told me. After reading these other posts, I wish I would have visited this site before I bought this headache of a machine. I will never buy Maytag again!

Home Depot is selling defective appliances manufactured by Whirlpool and refuses to provide a full refund. I purchased a Maytag washer and dryer from Home Depot in August of 2010.Washer broke in February of 2011. No parts available for repair, Whirlpool replaced washer after 4 weeks. This washer broke in July 2011. No parts are available for repair until August 17th.

The washer we bought has a leaking drain pump after 3 years. When I called, they initially told me the part has been flagged as a potential quality issue. When I was passed to the next level to deal with it, they stuck to the you only have a 1 year warranty policy. There are numerous websites indicating this has been an issue for these brands. Simply put, they dont stand behind their products.

Absolutely the worst washer we have ever had. Clothes come out smelling and look like they havent been washed. I should have bought a cheap washer, I bet my clothes would have been cleaner. The machine makes you think it is the best ever made by the looks and the price. Im sorry I ever wanted my money.

After only about a year or so - and it is out of warranty - the clothes are not clean - there are white type of scum marks left on clothes and especially dark clothes. This is even after I use the recommended detergent and less than normal and do a double rinse. Have to wash clothes again with no detergent with a double rinse again. Just so annoying. Would never buy Maytag again.

We purchased Bravos series Maytag washer and dryer. These are a match pair, the top loader, extra large capacity, very top of the line, $$$$$. The washer has already been replaced after many repairs, but the replacement new Maytag leaves a powdered gray residue on all the clothes because of the small amount of water it puts in the washer tub. Even on the deep water cycle, if I put in a blanket it will come out of the washer half dry where water has never reached it. This washer is the worst I have ever seen and cost top dollar. Maytag says nothing wrong but when I show them the powdered residue on the clothes they refuse to answer. This is the worst engineered washer ever, tangles the clothes terribly, does not clean the clothes and usually forces you to wash them twice to removed the soap residue left on them. I have tried every soap on the market, stacked clothing as Maytag suggested, tried various tricks Maytag has suggested, but nothing stops the grey soap residue. This washer cost almost a $1,000 for just the washer, it is a disaster. I have asked Maytag to refund my money but they refuse. If anyone else has their washer - we need to join in a class action lawsuit to force Whirlpool, maker of Maytag to replace this piece of garbage!!!

Purchased side-by-side with bottom freezer 2009 after Hurricane Ike. Fridge has stopped cooling. Called Maytag Customer Center and was told nothing can be done only to find theres a 10 year warranty on the compressor. This malfunction should not be an issue after 8 years. My GE fridge still works after 25+ years. Horrible!

Maytag Bravos Commercial Washer MVWX500XWO - This has been the worst experience with this $900 washer and breaking down in less than 2 yrs. Complete Garbage, New Locking Mechanism, now spin cycle not working. I am about to take back to Home Depot and let them have it. Garbage product - NOT WHAT MAYTAG USE TO BE... NORMAL 10 YRS NO ISSUES THIS MACHINE - STAY AWAY FROM.

Maytag Centennial 3.4 top-loader was purchased at Home Depot. It has never worked yet. On 4/28/12, the third weekend, I sat home for the servicemen to fix this junk machine. The first two times, the machine didn’t work ten minutes after they left and today they went to the wrong address. I have much more important things to do than to sit around and wait for someone to figure out what is wrong with this machine. It would have been cheaper for me to junk this brand new machine and buy a washer from a company that makes washers that work!

In 2006, my wife and I purchased a new Maytag refrigerator, the model type with the freezer in a drawer near the floor and the drawer is under the main door of the fridge. The thing has a sealed system and has a freon leak which makes it nearly impossible and not financially prudent to try to fix. Two repairmen were out and I spent $200 for them to tell me the same bad news. Its unbelievable that this junk wouldnt even last ten years. What is this, Russia? Ive heard some of their awful appliance experience stories and now this can join them. The reliable Maytag repairman who never has anything to - you know the one. He is probably dead. Hes not really the one to blame here though, it is the reliability of Maytag that is dead and will remain so for as long as this company is alive. Dont ever trust or buy Maytag if you care about making your investment in new appliances last! Dont do it, people!

Machine is very loud. Clothes do not feel completely clean when wash cycle has finished. I have a sense that not all soap has been removed. Dark clothes have streaks of white residue. Must turn clothes inside out before washing. Very disappointed.

Maytag Bravo Quiet Series 300 MVB700VQ - My wife and I feel this is one of the worst machines sold. We purchased it from Costco 2 yrs ago and had several issues over the years. Pump, locking, water level, small clothing items like socks getting in behind the drum and clogging the pump, and yesterday a flooding issue. That is right, my Bravo 300 did not shut off and the water ran continually with an LD code displayed. The water overflowed into the kitchen & pantry. The wood floors are now warped. We were home so we were able to shut off the water as the washer controls (buttons) were locked and not responding. We spent the better part of 3 hours moving items and wet vacuuming the house. We now have a dehumidifier running in hopes we can salvage the wood floors and minimize mold growth.I will note that I have a home warranty (third party) that covers repairs on my appliances, this washer included. The repair man thought it may be the pump, a line, and/or the control panel/module that need replacing. The repairs would be covered by home warranty.... but not the floors. There is NO WAY I am fixing any washer that flooded my home.Yesterday, I took a 3 yr old washer with known issues back to Costco. I was not happy with the manufacturers suggestions that I buy parts as it was Out of warranty. Again, I had a third party warranty so the repairs would have been covered! It is clear that the manufacturer doesnt CARE about the quality or the performance of this machine. I have found a FIX for these issues. We are buying an LG Washer that is more $ and is highly rated by Consumer Reports. Stay AWAY from this model and current repackaged models of Bravo/Cabrio!

The washer does not clean clothes. Thank goodness I bought a 4-year warranty because they have been out 4 or 5 times on washer alone. The dryer is now squealing and shuts off (a safety feature I am sure). The repair person replaced the pulley system and one belt, it still squeals and shuts off. I called the Maytag CEOs office and talked to a machine. Some really nice lady called me back and said she cannot do anything to help me. They have no consumer person to help you and troubleshoot with you. The washer is rusting, it is an inside washer. I live in SE, Texas and they told me it was due to living close to the coast. Well, Ive had GEs that never rusted and in fact, the problem is really with all the HE washers. I hate them. They do not clean clothes. I will never buy another Maytag or Whirlpool product again.

I purchased a Maytag dishwasher (Model No. MDB8949SBWO) in September of 2013. Within the first year (and under warranty) the control module failed. The dishwasher is now almost two years old and the second control module has failed. From other postings it is obvious that Maytag has a known defect in their control units. To replace control modules on an annual basis makes this an extremely expensive dishwasher to own.

We bought the combo Maytag Bravo 300. The issues with the dryer are that it doesnt heat right, have to run the thing twice, after the first 50 minutes the clothes are still damp and it sounds like its going to take off. We had a service man tell us that it was the fan blower rubbing. Now for the washer. It sounds like a b-52 taking off in spin cycle. I know that its the bearings, bearing kit 80 some dollars plus the bearing tool another 80 some bucks. Dont think Im going to invest in Maytags game. If there is ever a class action lawsuit please put me down or notify me.

I built a new house in 2006. As part of a builders package, we had all new stainless steel Maytag appliances installed. The side by side refrigerator compressor stopped after 26 months (of course, passed any warranty). No customer support through Maytag and as previously posted very scripted responses. Maytag microwave handle has broken off several times, the glass seal in the oven door was compromised and the inside glass is stained - most recently the on-going issue with my Maytag dishwasher model mdb5601. Ive already replaced the handle /door latch assembly twice and am confronted with the current dilemma if I should replace the control panel that now appears not to be working. It goes without saying that I will never purchase Maytag products again. However, I am not in a position to replace what are fairly new products. That being said, I am reluctant to purchase costly replacement parts given their poor performance and ratings as mentioned in this thread.

My refrigerator is a lemon! We bought a Maytag bottom freezer French door refrigerator model #MFD2561HEW in May of 2007. Less than a year later, it stopped working and ruined all the food inside. I cant remember the problem that time, but it was fixed by Maytag and we were reimbursed for a portion of the food we lost. Two years later, the temperature got warm in the refrigerator and freezer sections, and we were gone for a couple of days, so when we got home, all of our food was spoiled. This time we had an extended warranty in effect and they replaced a circuit board, but we were out the food. A few months later, the same thing happened. This time we were home and saved most of the food. The compressor was replaced, again under warranty, but it took 2 weeks to get the part. Now, less than a year later, the freezer and refrigerator compartments are getting too warm and frost is forming in the back of the freezer. When it finally does get cool, it freezes the food in the refrigerator section. It also makes loud bumping sounds. I paid $80 to a repairman today to tell me that theres nothing wrong with it, thats just the way it runs! He suggested I put a gallon of milk jugs filled with water in the freezer to hold the temperature when it starts to rise! This piece of junk is just 5 years old! When I complained, I was told to call Maytag and discuss it with them. This refrigerator was not cheap and I see that many others have had similar problems. How do they get away with selling an inferior product?

We purchased a new Maytag side-by-side refrigerator back in 2011 and for the last several months it has been leaking water into the bottom of the freezer unit when it goes through the automatic defrost process. The water freezes and after a few of these cycles causing the ice to accumulate and build up, it starts to leak out onto our kitchen floor. About every 10 days we have to open the freezer door, break up the accumulated ice on the bottom of the freezer and remove the ice chunks by hand. What a pain in the neck! Most of the time we can prevent the water from escaping, but not always. This is going to damage our kitchen floor, not to mention its a safety hazard for slip and falls, and/or fire or shock hazards. We have contacted Maytag directly, but nothing will be done as they say its beyond the 12 month standard warranty. They said one option is for us to purchase an extended warranty plan from them for only $359. Really? Are you kidding me?? They dont seem to care about a potential product liability property damage claim/suit, nor an exposure for a potential bodily injury claim. As Ive tried to explain, this is NOT a warranty situation, its a product defect situation and one probably worth a class action lawsuit based on the number of complaints Im aware of. They know its a product defect problem, but choose to ignore it at the expense of numerous innocent consumers. The only resolution seems to be filing your own lawsuit against them for some kind of remedy to this very aggravating situation that occurs every 10 days or so. Maytag used to be very good appliances, ones that were made of high quality materials, and lasted for years without any problems. Thats why I became a Maytag fan in the first place, but ever since they were purchased by Whirlpool Corporation, its not the same old Maytag we used to know and love. DO NOT BUY MAYTAG APPLIANCES - you will regret it!!

Maytag Bravos XL - I purchased my maytag washer & gas dryer on 5/12/12. In Dec 2012 the heating element went out. I had to wait a week for a repairman to come out on Dec. 20 to fix it. Now for the second time on Dec. 30th, 2014 the heating element has gone out. I called for a repairman to come out. I have to wait until Jan. 12th 2015 for service. I have 8 people in my home including 3 grandchildren. This length of waiting is ridiculous and very inconvenient.

I purchased Maytag fridge a year ago and it has been a nightmare. The freezer doesnt freeze items. the drawers were all damaged upon receiving. I have contacted Maytag for more than 10 times and 5 techs came that I paid 125 each visit to fix the fridge because I didnt purchase the warranty thinking it was a good product . It is not! They dont stand behind their word. They lie and they send unqualified techs the misdiagnose issue to collect service calls. Please avoid this brand by all cost. My experience is terrible and I never want to wish it on anyone.

Worst washer ever. Wish I had read all these reviews before I bought. I have had the same poor experience. Laundry doesnt even get wet while being washed. Agitation does not affect laundry. Just moves back and forth under laundry. Clothes do not come out clean. Feel I was ripped off.

I purchased two high end Maytag machines, one washer and one dryer, approximately 36 months ago. I did not buy the extended warranty because I was foolishly convinced Maytag sold reliable products. The dryer required service twice within the first 18 months. The washer, which is computerized, is almost unusable. The sensors dont work properly. It does not spin without continual restarting the machine. It takes me hours to wash one load of laundry, and even then it is not spun properly. I wrote Maytag headquarters twice via e-mail, with no response. Even though their website says someone will get back to you within three business days. I called Maytag on August 12th and was told there is nothing they can do because I didnt purchase the extended warranty. So the bottom line is you can spend thousands of dollars on their machines but dont expect them to last, or work. And Maytag will not stand behind their products.

I bought my Maytag washer and dryer in Monroe County in Georgia, USA in 1980. Its a 1979 product and it STILL works perfectly fine after 40 years! Im 64 years old now and Im hoping Ill never have to buy a new set although I would love one because theyre so pretty these days.

1st service call about 2 years after we got it. Put around $200 in it. Now broke down again. Service tech quoted $475.00 to fix it. So it was basically totaled after around 6 years. Nightmare kept getting LD (long drain) code. After hours of research I finally called service. Would not drain so I had to wring out a whole load of laundry and bail out the water by hand. Miserable experience!

I purchased a new Maytag dishwasher (model #MDB4651awb3) for $300, in December of 2009. Seven months later, the dishwasher refused to start. Some lights on the front panel would remain on, while others would not respond. The Maytag repairman made a house call and replaced the front control panel, and vent. After the repair, the dishwasher worked fine for nine months. Then, the same thing happened again. It refused to start with the same front panel light problem. I called Maytag, and since the machine was now past the one year warranty, they wanted $275 for an additional 1 year warranty, to repair the machine. Since I can buy a similar new machine for $25 more, and felt this was now an ongoing problem, (it would be the third panel in less than two years). I expected Maytag to offer more to take care of their lemon problem. Since they refused to reconcile the situation, they obviously no longer stand by their machines. I will no longer buy Maytag/ Whirlpool machines, and do not recommend them.

After purchasing this washer in 2007, the washer started to smell like sewage. At first we werent sure it was the washer and had a company come out to check the pipes. After this and calling Maytag complaining without any luck. We were told to buy affresh tablets and run it through the washer once a month. This last only so long and the smell comes back. Now when the washer goes into the spin cycle it sounds horrible. Again called Maytag without getting any resolve. I will never buy a Maytag again!

We bought a new Maytag Bravo XL washer in 2015 under the understanding it has a 10 year warranty. Well it’s 2020 and it starting leaking. Called customer service and lost 3hours of my life waiting for a person. Keep in mind I’m pretty handy and work on spa, and pools. And can troubleshoot things like this. I found the problem on our washer looked up the part and number.When I finally got a person on the phone they wanted to send a technician out to verify what is wrong with it. I was all for that but then they said it would cost $100. I said no because I already know what’s wrong and just need the part so I could fix it. I knew the labor would not be covered under warranty so that’s why I didn’t really need the tech to come. After a few minutes Maytag finally says the unit is. It covered under warranty at all. I asked yes it is because it’s literally written all over the washer it has a 10year warranty. So then Maytag goes to say they only cover the drum and motor for 10 years.So now I’m stuck with a washer that leaks that was sold to us under the pretense of a 10year warranty for parts. And now having to buy $280 worth of parts and shipping to fix it. Maytag advertises that they have the best warranty and they never break as their commercials imply. So they represent themselves And their warranty falsely. Buyer beware. Maytag is shady. I’m guessing Whirlpool is part of them so please do your research before you buy. 1. Customer service doesn’t exist with them. (3hrs hold times.) 2. Misleading warranty coverage. 3. Will not call you back.4. Try to extort more money from you. ($100 to send a tech out to confirm what you already know.)DO NOT BUY!!! Learn from our mistake.

When I bought Maytag Neptune top-load washer, it lasted three months. I had to have the rockers replaced. Three months later, the lock switches went bad. Six months later, the main circuit board went out. Thank God it was under warranty. Ive had this ** washer four years and it broke down once again. I dont have any warranty and the money. They want to fix it. Im going to go out and buy something else. Piece of junk. It makes no sense. And when the first situation arose, I did ask if it had been recalled and of course, they said no.

I think so much about Maytag dishwasher with electronic controls that I decided to fix up my Maytag mdb3700awx by replacing the motor. It has an old fashion timer. It was trouble free for 10 years until the water supply line fail and sprayed water on the motor and shorted it out. I got a use motor and pump from eBay for 40 dollars. The dishwasher should last 20 more years. Too bad Maytag dont make them like they use to.

I have a Maytag Centennial washing machine which is about 3 years old. In the past 6 months I have to replace the actuator twice. I have had Maytag washers for about 40 years. I will never purchase another one unless it is the old style. That would mean that it would be a used one. This machine is a bad purchase. Maytag use to stand for quality, but not anymore.

I had purchased a Maytag Front Load Washer Model no. MHWE300VW00 in 2009. Now the rear tub, basket, and belt are gone. I will never purchase another Maytag product and would not recommend them to anyone.

I purchased a Maytag microwave oven on July 22, 2011. It was delivered August 2. Model no. MMV4203DW, serial no. CK01001086. I paid $279 at Lowes Spokane Valley WA. I made a family brand name dinner for six in the original black carton, put the rack into the microwave, followed all the directions as the microwave was new. The carton melted inside and burned a place where the rack had rested. This melted before the time was up. I had followed all the directions. This was the first incident that was a problem. Next incident was a large bag of popcorn (microwave has two settings for popcorn--large or small). This burned the bag black before the allowed automatic setting. Third incident was another bag of popcorn, which resulted to a fire. I tried putting it out with a large lid, which now has permanent black smoke stains. The fire was so hot I could not remove the popcorn bag. I had to use two pancake spatulas to throw it outside where it continued to have flames and burned itself out. The next fire was with a baked potato. This was set for a regular potato setting. This fire was great flames. I tried putting this out with salt and a pan lid. I also removed it with a large metal strainer, an Asian type which is large, and used another spatula to scoop the flaming potato and took it outside while it continued to burn. This time the microwave burned itself out. All lights would not function so I unplugged it from the outlet. I have repeatedly told Ava that I had previously owned a Kenmore convection microwave and the only time I used the rack was when I baked something. She continued to ignore this and said that I used the rack to make popcorn, baked potato, etc.

On 9/8/09, I purchased a Maytag ceramic glass top range, model MER7662WBO. The right front dual burner has what look like worms in the burner. The other burners are clear. Maytag has replaced the top three times and the burner once. The top has gone bad again and they are calling this a cosmetic now and will not replace the top. I think there is a problem with the tops. I have purchased my last Maytag product. I buy for looks also.

Overall- I think washers aren’t made to last like they once were. Growing up- we had the same washing machine while living at home. It seems now- they only last 10 years if you are lucky. They should make more longer lasting machines.

Had this front loading washer 13 months when the circuit board failed. I pitched a huge fit as Maytag wanted to charge me 75% of a new washer for the circuit board replacement. Fortunately they caved. I like how well it spins out and washes well. The door gasket is hard to keep clean. Has fresh setting so clothes do not get moldy if you leave them too long.

Washing Machine MVWC6ESWW - The fourth time was October 12; I called. Shreka at Maytag said she would send someone out at no cost on October 15, between 12-5 pm. Justin called from AE at 5:05 pm stating he was on his way. He then asked for my receipts. We were moving and had packed many things. He said he would call and find out. He said they were out 7/2011, 9/2011 and again 9/2011 all for the same problem. I requested in September 2011 that this was a lemon and send me another. I was assured if the same problem occurs, it would be covered. Well Justin said it isnt covered anymore and it was due to being made overseas. The cost to fix it is around $350 to $400. The washer cost me $383.40, plus I bought the matching dryer of $403.39. This makes zero since. Please advise.

Duck bill valve for defrost water from freezer malfunctions, water flows into freezer freezes, then eventually overflows onto floor. Huge problem for folks with wood floors. Also a slip/fall danger especially for the elderly. When the repair line is contacted, they deny the problem and say you are the only one. But if you do your research, you find there are hundreds of complaints and in November 2013 they issue a service bulletin, but its internal, not meant for consumers to find out. So if you have this problem, go to the Consumer Product Safety Commission and fill out a complaint. Maybe then something may come of it.

I purchased a Maytag Bravo washer and dryer in 2008. I had a repair person out today on both units. I was told that it will cost as much to fix the washer as it would be to purchase a new one. As far as the dryer was concerned, I was told to live with the timer issue rather than replace the expensive mother board. I was also told that the drum bearing issue with the washer is fairly common with the Maytag machines. It looks like the Maytag repairman isnt so lonely anymore! I paid a lot of money for these machines and they amount to a hill of garbage after three years. I may be buying a new washer, but you can bet your boots it wont be Maytag/Whirlpool!

Washer gets out off balance too easily. If I put in a couple of towels, it will almost invariably stop part way through the wash cycle. I was told you have a great washer! Its the last of the two-belt Maytags! My reaction: so what?

Had our house built in 2009 and the builder carry Maytag Appliances. After 3 years every single appliances start giving us problems. First the refrigerator not getting cold, got it fixed. Then the dishwasher panel, then the built-in microwave, then washing machine. Just the other day the refrigerator broke down again and I was told the compressor was bad. Really? Whats going with this company? All the appliances from this maker dont have longevity. I have 20 year older refrigerator from GE and its still working. Please do not buy this garbage... Its a waste of your hard-earned money.

Maytag HE Top Loader Washing Machine: I have regretted buying this piece of garbage since my first wash. This washing machine is complete waste of money and a piece of garbage. The Auto Sensing doesnt work and doesnt cover the clothes with enough water. When the deep water wash is chosen the clothes just float around but the agitator doesnt get them clean. Dont waste your money hoping it will work, because it wont. Maytag used to signify quality that is no longer the case. I am going to also give a bad review to the place I purchased this piece of garbage because all stores need to discontinue selling this junk.

13 months after purchasing MDB7749SBM3 dishwasher this lights started making no sense. For me the buttons still work, but it seems like only a matter of time until they stop working too. Like many others, I opened up the door and found the corroded ribbon connector (see photo). It wasnt damp so since the corrosion happened at the point where a ridge of plastic presses the ribbon against the hot handle, I suspect heat. Obviously a design flaw. Come on Maytag. Recall?

I purchased a top load Maytag washer the spring of 2019. My clothes come out partially dry, with a film/residue, and debris left on them. I was told that they use considerably less water; however there is not sufficient water to wash away small amounts of anything left on clothes. I have contacted Maytag 3 different times. Each time my concerns have been dismissed. The only solid advice they gave me was to use less soap, which hasnt changed anything. They also told me to clean my clothes before I put them in the washer (we have no children at home; Im not talking about really dirty loads). They told me there was nothing they could do, and I was just stuck with the washer. I am completely dissatisfied with this product and the Maytag service. I would not recommend their washer or their service. The dryer works just fine.

Purchased this unit back in November 2011. Sometime this year it started leaking water just like many others from the freezer unit onto the floor (many times large puddles). Im tired of the permanent towel on the floor to absorb the water to prevent a potential slipping hazard. I too went online and found a very nice video on youtube which showed how to disassemble the freezer compartment. Took everything apart and noticed that there was water frozen on the supply line. Melted this and put everything back together, for about a week there was no water leaking so I figured all was well. About a week later the puddle was back so I sent an inquiry to Maytag and let them know I had an image of the issue and asked if it was covered through manufacture warranty. Here is their response: Your email is extremely important to us here at the Customer experience Center and we sincerely apologize for any delays in responding to your email. We are working diligently to respond over the telephone and through email to all of our customers. We are sorry to learn of the problem you are experiencing with water leaking from the bottom of the freezer. Unfortunately, we are unable to determine from this location the exact cause of the problem. We recommend that you contact a certified technician for an accurate diagnosis. Once the problem has been diagnosed, please contact us back so that we can review the concern further to determine if assistance is available. For your convenience, we have provided below service providers in your area that you may contact for service. Aries Appliance Service (925)367-7708, Vigil Appliance Service (925)371-7701. You are a valued customer and we do apologize for any inconvenience this concern has caused. We invite you to contact Maytag again either by calling (800) 344-1274 between 8:00am to 8:00pm EST weekdays or by emailing whenever the need arises. When calling please press the available option or stay on the line to reach a representative.Frustrated I went online and found this forum where hundreds of other people had the same issue and that many of them were resolved by the new P Trap. So I watched another video by the same guy on youtube that showed how to replace the P Trap. I went online and found the replacement P Trap Manufacturer model # w10619951. One of the comments there actually said to call Maytag first as they were able to get a replacement P Trap for free. I believe if it was under a year old they would also pay for the labor to have it replaced. So this morning I called Maytag, the first guy Jim said I would have to have a certified Tech come out (76 dollar service fee, plus whatever the labor would cost) and Maytag would cover the cost of the part. I asked Jim if he could just send me the part and Ill do it myself, he reassured me that he could NOT do this and that the system was very specific. I told him I did not understand that a bad design and known quality defect, why should I have to pay several hundred dollars to fix? He told me that was the way it is. I asked to speak to his supervisor and put me on hold. Not only was the hold music extremely obnoxious but there was a loud humming noise as well, I waited for 10 minutes hung up and called back. I spoke with Maggie this time. I told her I wanted the part sent to me and if she couldnt help me I wanted to speak to a manager. She said she did not have the authority to ship me the part without approval. She said she could ask for approval and after waiting for about 3 minutes she came back on the line and said she spoke with her supervisor and that they would be sending me the replacement P trap today via FedEx. Had they not sent me the part my next stop was going to be the better business bureau..

I own a MAYTAG BRAVOS XL* TOP-LOADING HIGH EFFICIENCY LOW-WATER WASHER. On 9/1/15, after reporting a problem, a service person arrived to assess the problem. His diagnosis led to a second visit on 9/8. On the second visit he replaced multiple parts, assuring us that the problem was fixed. When this proved to be false, we called for a third visit; this time a different person arrived. After disassembling the washer he found a large hole and another cracked area in the inner plastic portion of the tub. We made a fourth appointment for repairs, receiving assurances that it would be repaired at that time. I received an e-mail today (9/16/15) informing me that an additional 7 days would be required to arrange for delivery the required part. In the interim, my wife and I are forced to use a local coin operated laundry about every three days, totaling 7 visits at approximately $25 and 3 hours per visit before the next scheduled appointment. The compensation offered, 9 months extension of the existing warranty is woefully inadequate. I want the appliance replaced, as history has taught me that you are obviously unwilling or incapable of repairing it correctly in a timely manner. Additionally, I want the initial warranty that accompanies a new product extended to a full 3 years. We have paid out over $150 and wasted 18 to 21 hours of our time unnecessarily. I expect compensation for the funds spent as a direct result of the bungling, incompetence of your service staff. My questions are these: 1. Was the part defective prior to installation? 2. If so, why did the representative not notice it and refrain from installing a broken part? 3. Why was there no mention of the damage on the first visit? 4. If not, how did the damage occur? Did the service man damage it and fail to report it? 5. What caused the delay in obtaining the part? I have other questions, but will no longer spend any more time on this debacle. I cannot honestly say which is worse, their quality or their pathetic version of customer service.

Very dissatisfied with Maytag Washer Mod MVWB835DW0. This Large Capacity machine does not adequately clean a large capacity of clothes. In order to get a half decent wash performance from this machine, fill the machine only 1/4 full. Even using the recommended manual, I was very dissatisfied with the way my clothes looked after washing them with this machine. While I have been unhappy with the performance of this machine since purchasing it. What motivated me to leave this review is when my pants had the same sand debris on them after the wash as they had before the wash. I will be looking for a new machine this weekend. IT WILL HAVE AN AGITATOR TOWER!

After my divorce, I bought a new house for my youngest son and me. It came without a fridge, so I used some of my settlement money to buy one I had been dying to get - stainless, French door, with bottom drawer freezer! It worked fine for the first 9 months or so. Then, water started pouring through the ceiling of my downstairs master bedroom. Turns out it was coming from the freezer water line. Ceiling tiles ruined, carpet stained. Then it started making this god awful noise. It starts, rumbles for a while (long enough to wake everyone up or give the dog a coronary), then is quiet for a while. Next, I open the freezer to find a sheet of ice across the bottom of the drawer. I assumed I had done something, so I got rid of it and thought nothing else of it. Last night, I get ready to make dinner and there is this blizzard of frost all over the freezer. It looks like a winter wonderland. I am afraid to see what is there when I go home and even more fearful to attempt to use my warranty.

The microwave is 5 years 6 months since purchase model MMV4203DS. Fire started at rack clip left front rack, was cooking bacon. Called Maytag and according to them and manual on page 3 is only for 2-level cooking to avoid damage to microwave oven. DOES NOT SAY WILL CATCH FIRE OR THE RACK CAUSES SPARKS AND BACON SHOULD NOT BE COOKED IN A MAYTAG MICROWAVE. But according to Representatives of MAYTAG ** its my fault for not reading my manual. YES AND NOT HAVING THE SERIAL NUMBER THAT IS ON A PAPER TAG IN THE WHIP ZONE. The was gone from keeping it clean faded out. So I cannot be helped without the model and serial number.