I purchased a front load washer over 2 year ago and the bearing on it has gone bad. Maytag jumped at offering to ship the parts to me at no cost (which at the time I thought was great). I waited 3 months to finally get the part, because it was on back order, and now was just hit with the labor bill! If I would have known a brand new washer was going to go bad after 2 years and cost me over $500 to repair, I would have gone with another brand, In fact, I will never buy a Maytag or Whirlpool. I will ensure that I tell everyone and post comments all over the website about how ** of a product Maytag/Whirlpool produces. Companies like these give the U.S. a bad name! Maytag, you suck!

The machine has left pin-sized holes in finer clothing since we first used it. I had purchased the extended warranty so they were called out to repair the issue four times during the warranty. They replaced the drum, but I still get holes. I think it is because there isnt enough water to rotate the clothing and it rubs repeatedly against the same spot on the other clothing. I have a see-through lid and you can see that the clothing just moves very slightly in the same position. I separate all clothing that has a zipper or any trim that may rub against the finer fabrics, but I am still getting pin-sized holes. We requested compensation or a new machine. They extended the warranty. We have replaced enough clothing that we are now buying a new machine. It will NOT be a Maytag.

I had the exact same experience as the Tampa person with my Maytag dishwasher (Model: MDBTT60AWW). It was not cleaning the dishes, even when I thoroughly rinsed them. Plus, it started leaking midway through the cycle. Since the warranty was expired, I purchased an extended warranty in July 2012 for $296 (yes, in hindsight, I should have just bought a new appliance, not Maytag). I had 3 visits from 2 different technicians, both telling me the dishwasher did not leak. One telling me I was using the wrong kind of detergent and thats why dishes werent getting cleaned. The other telling me that there were too much suds and that could cause it to leak. So, I should pour a tablespoon of cooking oil (yes, cooking oil) in the dishwasher when it starts leaking and that will cut down the suds. I dont think so!Then, I found out a couple of weeks ago that this model was under a recall since 2010, not related to the leak at all. Yet, Maytag still sold me the extended warranty (wheres the ethics of that?). I requested a pro-rated refund of the balance on the warranty - and wouldnt you know that with the technicians service calls, the amount of time used on the warranty (6 months) plus an admin fee - I have used $296.48 of the warranty amount. It is almost to the exact penny of what I originally paid, so I will not be receiving any refund. They are only giving me a debit card of $150 or $250 once I buy a new Maytag to replace the recalled model. I do not want to continue down this frustrating path known as Maytag appliances.

Maytag Dryer- Bravos XL - Waiting for my third service call since purchasing my dryer less than 2 months ago. After 2 service calls the repairman found a piece of the mold that should have been removed at the factory causing problems. Now, my dryer made a weird noise, sparks flew and it no longer works. After calling the seller and the manufacturer requesting a replacement, they feel it should be repaired (again).

Bought a washer and dryer from Lowes in June of 2016. Have had service on the dryer 3X and washer 1X since. Two person household that uses product a couple times a week. Dryer drum stops rotating / temp control fails / buzzer doesnt work / motor freezes up / washer makes loud banging sound at the end of the cycle every time....sounds like someone is hitting it with a hammer....Today I want a local serviceman to replace the motor but Maytag insists that I have one of their reps come out next Tuesday to examine the product and then go from there. I have been on the phone for 45 minutes trying to get them to pay me $128 for the failed motor that I will send them for inspection. They will not cooperate. They are hiding behind some BS policy. I want to inform you all in case you are contemplating a Maytag purchase. I will not purchase nor will I recommend Maytag to anyone.

I had purchased a Maytag Front Load Washer Model no. MHWE300VW00 in 2009. Now the rear tub, basket, and belt are gone. I will never purchase another Maytag product and would not recommend them to anyone.

Seems a little ** one of a small child crawled into the washer and a sibling turned it on. We have been married 35 years and seen a lot of washers and this is by far the worst wash machine Ive ever seen. How would you rather do my wash in an old fashioned mangler? Very unsatisfied customer.

I bought this large capacity top loading wash machine about 22 years ago and it has yet to fail me. It had never needed any repairs and cleans my clothes wonderfully. The brands reputation is well earned. Great washer!

Maytag Bravos Model MVWB750wq1 - After only two years, the washing machine finally died. The machine was on a f51 code - hardly anything was in the washer. I also smelled a burning smell - well, that was the pump. The machine was not pumping water out. After the repairman came out, the contract company is saying they are not covering this because there was rust reported by the repairman. How can bearings inside a washing machine be rusted? This is a washing machine, isnt it? How are they building machines that deal with water and rust?! I will never buy another Maytag product - thats a promise. I spent over 2000.00 on this set. Never again.

Bravos 4.3 High Efficiency Washer - The worst washer ever. I recently returned from burying my step-mother. She actually used the same washer and dryer, by Maytag, for over 50 years. Those days are gone forever. This is my second set of Maytags in ten years. The first literally stopped working just after the first year warranty ran out. I still have them inside my pantry, like a set of anchors. Notwithstanding that, I thought, Maytag was a good brand, it must have just been the style of machines, so I purchased these in January. After over six months of usage, I am amazed at how many times I have to wash a single load of clothing to get the items clean. Who cares if the machine saves water? What was wrong with having an agitator? I literally have to remove freshly laundered clothing, turn it over and run the wash again to get the top of the laundry clean. I have had a blanket finish for the fourth time to get it clean, only to have to hang it outside because it is so full of water, the weight keeps it from spinning properly. And why would you remove a timer feature which permits very busy, working people, to wash their items while they are on the way home or in the middle of the night so that there is no waiting to pop the clothes in the dryer? None of the cycles takes less than 80 minutes to complete. Who has 80 minutes to wait on the washer to do its job? I am so upset about the amount of money I spent on all of these machines. Just think, I could have brought the over 50 years old set home from my step-mothers and had a washer and dryer do what they were supposed to do -- clean the clothes.

This washer sucks so bad. Just got it a few hours ago and its absolutely horrible. The water just runs for the wash cycle. And I was told by the salesperson at Best Buy that it would save you water. Thats not the case. There is enough water to run over all the clothes. It doesnt agitate enough to even move the clothes around. The clothes basically sit at the bottom of the tub in the water doing nothing. This Maytag Bravo washer will be returned tomorrow. Me and my wife are highly disappointed. I wouldnt recommend this to anyone. Weve decided to just get the old washer fixed and go from there. There are too many bad reviews for this washer to still be on the market. We feel that this was a total waste of time, energy and money.

Yesterday I was using my washer (small load of clothes), I was with my baby in the laundry room when suddenly there was a horrible noise and the door of the washer opened, he hit my back, something fatal could have happened. I do not know how it happened but a piece of concrete was inside the drum. I do not want to imagine what would have happened if that piece came out and hurt my baby. I spoke to the company and explained what had happened to me, but they do not want to be responsible for what happened because the washer is in Tijuana (border with San Diego), I bought the washer in Pirch San Diego California in 2015. Maytag United States is responsible for this defect. Dont buy this model:mhw8100dc extra large capacity washer with steam and powerwash® system-4.5 cu. Ft.

I have a Maytag Centennial washing machine which is about 3 years old. In the past 6 months I have to replace the actuator twice. I have had Maytag washers for about 40 years. I will never purchase another one unless it is the old style. That would mean that it would be a used one. This machine is a bad purchase. Maytag use to stand for quality, but not anymore.

I bought my washer in 2016 and now it’s broke again. This is the fourth time! I’ve gone everything to take care of this and it’s a lemon! I will never buy Maytag again. I want to buy USA products but four times for repairs in three years is way too many. I guess it doesn’t matter what name is on it. My last washer was a GE and was still running after 15 yrs when I bought this one. Not one repair ever made on it! I’m telling everyone to stay away from maytag.

Didnt even want to put 1 star but that is the lowest you can give. Maytag microwave less than a year old paid $350. Door clasp broke. Took two weeks to send a repairman out, he came out and of course did not have the part -- took another week to get it. Fixed the door and then he crashed and burned the microwave shorted it out and now it is totally dead. That was 2 1/2 weeks ago. Maytag refuses to replace the microwave and insists that the same incompetent service company come out and fix it. Meanwhile I have to call Maytag every other day to find out when the correct part to repair the microwave will be in. Was told it would be in two days ago. Never got a call to schedule the repair, called today to find out they never even ordered the part. Here goes another week without my microwave. Not only does Maytag have horrible customer service, they manage to find unskilled repair techs with equally horrible customer service! Will never ever buy another May useless Tag appliance again.

Just like so many others, our Maytag 300 Quiet Series, just 2 years old, has a malfunctioning control panel. Repairman told us this has been an ongoing problem with Maytag dishwashers. Steam/water gets into the control panel.For a while it worked on and off and now it is dead. I am saving up to do the repair, but in the meantime the dishwasher sits idle.

In 2011, we purchased this Maytag Centennial MVWC200XW1 washer. It will not complete the cycle when it goes into rinse and spin, will not empty water and once the cycle starts, it sounds like someone is inside with a hammer banging on the basket. Clothes come out with a powder residue on them and several pieces have had holes. Called Maytag and was told there was no service available in our area. I will never purchase another Maytag product. Used by two adults a couple of times a week, this machine should be trashed. I have to hand-wring our laundry as we cannot afford to replace at this point. My last washer was a GE and I had it for over 20 years, we replaced it because we moved into a new home thinking Maytag was the best out there. I checked for a recall because there are so many complaints on other sites but found none. We purchased from Home Depot and of course, they are no help.

My Maytag refrigerator was purchased from Home Depot less than 3 years ago. It is a French door, bottom freezer draw model #MFI2569VEA1. Every four days, there is a huge puddle of water at the base of the unit and it is starting to ruin my ceramic tiles. I tried the online video solutions to no avail. Home Depot wont repair it, they told me to contact Maytag. Maytag wants me to purchase a $375 warranty, which is 30% of what I paid for the refrigerator. I will never buy a Maytag refrigerator again, or any Maytag product for that matter. They once stood for solid reliability and peace of mind, now you get a piece of junk instead. I cant even sell it on Craigslist if I wanted to because who would want it? If a class action suit is ever initiated, Ill be on board. I hope Consumer Affairs contacts me.

I purchased this dryer in September 2011. By August 2012, one month before the warranty expires, the thermo fuse blew and the dryer would not dry; no heat. I replaced fuse and 30 days later, it blew again. I replaced it again and now, March 2013, 6 months later, the same thing; the thermo fuse blew, no heat. The vent is clean and air flow is very good. Maytag will not admit a problem. This is not an inexpensive dryer; it may be cheap, but not inexpensive. Maytag quality appears to have vanished. I have Maytag throughout the house but will think twice before purchasing Maytag again. Chinese produced parts/products are inferior. Maybe Ill look at Bosch or LG from now on.

Purchase a Maytag Bravo XL Washer Model MVWB850YWO from a major Home Improvement store in January 2012 with a 4 year service plan. Since this time I had to replace a motor and 4 (that is right 4) control panels. Although I am covered under a protection plan, the cost of laundry services and an outage of 2 weeks for each event is very costly. This time I call Maytag for support on their product. Looking for someone to say that there is something wrong with this machine. I want to hear that their product should not perform like this. I was told from a supervisor in these words that Mrs. we only care about the machine the 1st year. After that you are on your own. When did Customer Service lose the service part? When did companies stop caring about their products they produce? I never heard I am sorry youre having trouble or even a recommendation. A machine this new should not have 4 control panels replaced. This is the reason no one wants to buy a Made in the USA product anymore because we know the employees working there do not care about keeping customer relations.

I cant warn you enough NOT to buy this design flawed machine. Ive only owned mine two months from Home Depot, the install was a nightmare and now due to a poor design flaw, if you miss loose coins or anything in pockets it will get trapped between the drum and the tub causing rattling and noise during spin cycle. Guess what? Service calls EACH time this happens. This is nothing more than a $750 piece of junk. I feel like its marring the whole feel of my new house. I hate hate hate this washer and am trying to get Home Depot to take it back, Maytag to refund me or sell it at a huge loss. This is NOT getting anything you pay for and I vow to NEVER EVER buy Maytag again.

My washer is new, out of warranty, and about 2 and a half years old. All of a sudden, with no warning or previous issues, the computer board in the washing machine malfunctioned which caused a humming noise, it would not cycle into the next wash phase, the time would go up instead of down, I could not change cycles, and when I would push the power button there would be a delay of power coming on. I unplugged and called my local appliance repair and he said he sees problems with this model regularly, although not always the same issues.Before purchasing I scoured the internet for reviews on different units to make sure I didnt get a lemon. I think Maytag saw the error of their ways quickly and stopped making these before people caught on. This model is no longer being made. I like matching units, so it meant either shell out $500 for replacing the board, or replacing both the washer and the dryer that still works, which would be about $1200 or more for a new set. I chose the least expensive route for now. Not that it matters where I bought mine, but Home Depot and it was on clearance so it was a good price. I have now made up for that difference in repairs.

Home Depot is selling defective appliances manufactured by Whirlpool and refuses to provide a full refund. I purchased a Maytag washer and dryer from Home Depot in August of 2010.Washer broke in February of 2011. No parts available for repair, Whirlpool replaced washer after 4 weeks. This washer broke in July 2011. No parts are available for repair until August 17th.

M1BXXLZYB00 - This is the worst appliance I have ever owned and I am 56 years old. Very noisy, freezes my produce and actually anything in the refrigerator. Yet the freezer wont freeze popsicles. Had 2 service calls on the fan and or fan motor in the first 6 months. Now 2 years later we have replaced 2 compressors and had to pay 200.00 labor to have installed. Now the compressor is out again not even 30 days after the first 2. Whirlpool wants to send another compressor and the poor repair guys are suppose to do it for free now because it is within the 30days. The offered me to buy another refrigerator with prices of 699.00 and 519.00. My fridge in the garage is way more dependable than this one and I have had for 10 plus years with no problem.

I purchased a Neptune washer/dryer front loader. All Neptune washers have basic design flaw over which the company should be sued. Since the bulk of the weight is in the front of the horizontal wash-drum, the entire assembly is suspended by a rear mounted bearing allowing the drum to spin. That bearing assembly is woefully under-designed and not able to support the unequally distributed weight that is inherent in any front load design.Since the forces of gravity cause a loading of the rear bearing on the front of the bearing raceway only, the machine is doomed to catastrophic failure of the entire drum system--and they all do this. When the washer goes into spin mode, it sounds like a jet engine taking off and that is a symptom of the bearing design beginning to fail which begins on the first use of the machine. The cost of the drum assembly/bearing and the labor is far more expensive than buying a new machine and therefore, not worth it. Avoid Maytag products at all costs.

We bought this stove in 2014. One knob got stuck while my teenager was cooking food on the gas stove. He called me at work worried because he couldnt turn it off. My husband left work right away to go home. We thought it was just a bad plastic knob. Now a second knob is stuck in the on low position. There is a third knob that feels hard to turn. That will be 3 burners. This is ridiculous. Its a safety hazard. We consumers have to worry if the house will burn down, get CO2 in the air, and if our family and children are safe. We thought Maytag was a good appliance. I will not buy another Maytag. They should recall this stove top/oven. I have read so many of the same complaint on this website as well as online in general. I cant believe they continue to sell this with this much of a safety issue. Please take it off the market.

I have recently purchased a washing machine. Within the first week I was calling a repair person to fix it. I HATE this machine, and I dont think that its fair that I get stuck with it because of the way it was made. I have to constantly redo the load because it doesnt drain and rinse. When the load is done the clothes are still soaked. I dont understand how technology can go backwards when it comes to washing clothes. SOOO DISAPPOINTED!!!

In December of 2013, I purchased a Middle of the Line Maytag Dishwasher model #MDB8949SBW for $600 plus $200.00 for install and removal of 5 yr old Kenmore. At that time I thought I did my research and saw no major negative flaws on this type of machine or similar machines. This replaced a 5 yr old low line Kenmore that just upped and died. Installed just before the holidays, this Maytag machine seemed to have worked tirelessly until a few days ago August 18/2015. The computer controls went haywire. I was hitting normal start buttons and other buttons on the other side of the control panel were blinking and lighting up. Worse was trying to cancel and the control boards were not responding. Even hitting the start button, the machine would not turn on. Finally looking at the facia, I see the tabs of the flexible plastic frame that hold the control panel popping out from underneath the white facia plate. Snapping the frame back in and applying a lot of pressure got the machine to operate. With a family of four and minimal storage space, this machine is used approx once a day. It appears over the year and 1/2 by pulling on the plastic handle - which also happens to be the computer control board frame, the computer has separated from its mount and has allowed moisture to hit the control board/computer and wreak havoc on the electronics. Looking up this model online NOW, I see I am not the only one with Dishwasher computers failing within a year or two- just out of the one year warranty. A Call to Maytags customer service has the computer control board alone cost $160.00 plus the service tech and his labor fees reaching in excess of $450.00. The CS rep gave me a repair discount to $267.00 and a week wait for the Service Tech for this problem to be fixed. I bought this machine on two premises - one for its price, it was the only machine that offered 3 spin jets that really do a good job in cleaning dishes and 2, I owned a 1984 Maytag dishwasher in another home with computer controls in the handle and to this day, that machine is still running flawlessly! My only issue with the 84 Maytag machine was after 4 years the door gasket went - too much soap - replaced and no issues since! I expected similar performance with this one. I guess I have to spend north of 3 bills for similar performance and quality. What was I thinking?

I purchased a brand new MHWE450WW01 Washer and MGDE500VW2 Dryer in February. The dryer takes forever to dry something; seriously, 3 hours for jeans! The washer sounded more like a jet engine taking off. I called Brothers Main, they sent a service person who identified right away that it was a known problem and he had over 6 repairs already, but be prepared to wait up to 3 months for the replacement parts. This is ridiculous. The service center, you can never get through to them and when you do, they dont seem to care. I had a 10-year old washer that made less noise than this brand new one that I spent $1800 for.

I have been using washing machines for 50 years. This is by far the worse piece of engineering I have ever used! On deep water wash, I would expect my clothes to be covered by water. I actually have to add by hand, four buckets of water and even then the clothes just float on top. The agitator NEVER pulls the clothes down to the bottom of the tub, they just move back and forth. The clothing that sits on top of the water, never gets totally submerged and is still on the top of the pile when the wash cycle is done. I will NEVER buy any MAYTAG product again. Lowes wont help me. I want to sell it, but in all good conscience, I cannot unload this on another person. I cant even feel good about donating it as it does not work...It is Junk!!!! Shame on Maytag for selling a scam. If there was any integrity in this company, someone would contact me and give me a better model.

Purchased Maytag Double Range MGT8720DH00 in March 2015. Within 2 months had to call gas company due to leak and service came out to fix it. Now anytime my house is closed up during a vacation or extended period away I come home to a locked range with a warning message to check to make sure that the knobs are off. Had gas company (who also called fire department) to come out tonight after returning from vacation with same issue again. They tested and said CO2 was ok, but to check reviews for similar ranges and I have seen repeated issues in reviews for Maytag products. The firemen all commented when they saw that it was a Maytag so it seemed like they have seen these issues before. Very scary to think we could be exposed to a constant low level gas leak in our home. Keeping windows open at all times is not a realistic option.

I bought a Maytag stainless steel refrigerator w/ freezer on the bottom. Since 6 months fridge being in my house I started to have problems, rust on the doors, water coming out of the bottom, freezer door got stuck w/ ice and couldnt be opened, butter, eggs, milk can be frozen one day and the next they have mold and bacteria because of the changes in the cooling system, among my problems. And what? Well yes thank you so much for the guarantee Maytag has in Puerto Rico, IT SUCKS! They been in my house more than 5 times and nobody really says whats wrong. They supposedly change the computer, still having problems, and this was done after more than three times visits from Maytag guarantee. Im still paying for the damn fridge and DO NOT HAVE A RELIABLE REFRIGERATOR. Im wasting too much food, Im obligated to buy food almost every day cause Im scare to give something that may be bad and my family will be food poisoned. Whos going to pay me or my family if something happens. Maytag is still running falsely commercial ads and somebody MUST STOP THEM. This appliances are not free or cheap. PLEASE help us because Ive learned that Im not the only one having problems in Puerto Rico w/ Maytag. Also I believe Maytag is using technicians not ruled by the government of Puerto Rico and thats why the service is horrible.

All my kitchen appliances are from Maytag, however I would highly recommend buying the extended warranty for any appliance you buy. Maytag is not helpful to customers when it comes to repairs. They will recommend you their authorized companies which here in Colorado Springs are the one with the worse review and already knowing the the repair will cost more than the cost of a new one. You will have to be available 5 hours of your day and spend $110 for a guy to come to your house and tell you that the repair will cost more than a new one. Oh and if your microwave is a 2.0 CU like mine you will have to pay $300 plus in double labor because your microwave will require two people to take it down from the kitchen cabinet.

Do not buy this refrigerator!! It’s small on the inside but to top it off the vent is on the left side, not in the back, so everything freezes on the left side of the refrigerator. Plus they positioned the light right in the front at the top so you cannot put a gallon of milk or anything tall. Not orange juice, apple juice, nothing!! Horrible design. I’ve had the repairman out, he said he couldn’t do anything about the freezing on the left side unless he turned the temperature up on the fridge and on the freezer. We tried that & The ice cream was so soft, almost melted. The problem then was the temperature was too warm for milk and other items. Not a recommended temperature to keep cold items. He said I would have to keep everything away from the back & the left side to use it without freezing my items. I’ve lost a lot of food because of this. Very unhappy with this refrigerator!!

Maytag bravo - thought it would be a good brand/buy/new technology. Absolutely nothing to like. Complete junk. Bought it in June 2013. Doesnt get things clean and takes a long time to not do that. We thought a good reputation from a major brand would mean a durable efficient washer with a reasonable capacity and good features. Unfortunately we didnt know when we bought it what a bad design/investment it was. It has destroyed numerous garments with fraying and doesnt rinse soap or dirt out because it doesnt use any water.The bravo from Maytag is supposed to be low water efficient. Unfortunately, it doesnt use enough water to wash clothes, no matter how little or how much HE soap you use. It frays clothes, leaves soap residue, wont wash jackets or blankets or bulky things, takes forever to NOT get things clean, doesnt get heavy stains or mud out, the list goes on and on.... oh, and its expensive, and breaks down a lot. I cannot believe that there has not been a government recall where the people who were unfortunate enough to buy one have been given a large amount of money back.

I purchased a set of Bravos 4 months ago and what a bad purchase! I wish I would have researched here first. Being environmentally concerned, I bought it because it was supposed to be high efficiency and low water usage. My clothes are being destroyed by this machine. They come out in a massive tangled ball, covered in ink and animal hair (after a wash or two, they are completely embedded into the fibers). Sometimes there are dry spots after I take a load out of the washing machine. No idea how that could happen. It torn my favorite sweater, ripped sheets, bore a hole in a towel, ripped pillows, and DOESNT EVEN CLEAN! I have to wash my clothes twice MANY times to get the dirt out which doesnt bode well for energy efficiency. Im calling them again today to try and get them returned for advertising that they will save me money. Not even close! They are a rip off! I gave my 35 year old set away and wish I had it back! Maytag is JUNK!!!

I have the Maytag Bravos washer and dryer. The machine has broken several times every year, and every year, Maytag makes me feel like it is my fault. They built a machine, and they do not stand behind it. And I cannot get a local machinist to work on it. I have asked Maytag to replace it from the start, and they refused, telling me its out of warranty. The only thing out of warranty is the frame--all parts are new. Here is the history:On 1/04/2008, I purchased it from Home Depot, and it cost $815. Then in 4/2009, there was an F51 code, and Maytag replaced the mother board after long hold times and much pleading to help me. They said they could do nothing, because it was out of warranty. It took manager to manager to manager to get the agreement to extend the warranty. (I then found that this was a regular Maytag issue.)From 9/2010 to 10/2010, an ld code occurred. The approved Maytag scheduled service had to come out 4 different times to attempt to fix the issue. One time, they said it was broken wires for the drain pump. The next, it was off balance; and the next, it was a sensor. Then the next time, they replaced the mother board again, and again after much argument that the part was less than a year old. Each time, they get more and more difficult to deal with and made me feel more and more like I am asking them for something unreasonable. The service guys said the washer was like new.... All new parts and I would never have a problem again. It cost $80 after argument, and Maytag covered the parts.Last 2/2011, problems include a fast spin, ld code, and off balance; and it stopped working. It needed new suspension rods which cost $250. Maytag paid nothing. Then in 8/2011, ld code started again, and I would have to turn off to drain and then restart to spin. Maytag called in a service call, and they never showed up. Every time, they said they read over my file and that theres nothing they can do to help me. And no one else for me to speak to.In 10/2011, the ld code came on permanently. The Maytag call I made this time again said there was nothing they could do to help me.I am so frustrated; I dont know what to do next. I threw away an older set working washer and dryer, thinking I made a great decision to upgrade to this new set. Now my family of 5 cannot wash our clothes. No one will work on the washers locally, and Maytag treats me like Im complaining for nothing and I should just spend endless dollars to fix this machine. And Im at a loss. I had to get a part for the dryer the other day, and the parts store person told me that this washer is one of Maytags mistakes. if that is so, why wont they help me?

We purchased a Maytag Centennial line washer (Model # MVWC400XW0) and paid a little more hoping that it will last longer than a normal washer. After just 14 months, the washer breaks and we are forced to buy an extended warranty from Maytag for $300. The warranty price seemed a little high; however, the only other option was to buy a new washer. The repair guys showed and said it should be fixed.After just three weeks, the washer broke again with the exact same symptom. Since I had the extended warranty, I called in another ticket. A different repair guy showed up and he said the first guy messed up. He said the guy misread the diagnostic code and didnt even put in the part that he said he replaced. The repair guy checked with Maytag and they told him it was no longer cost effective to fix our washer. Really? They overcharged for the warranty and wont even repair it when it breaks. The only reason I can think Maytag would do this is that they know the washers are junk.

We had a Neptune Maytag for over 12 years, best machine ever but this one (Bravos XL) is complete junk. We have been very disappointed in its ability to clean clothes with the length of time to complete its cycles is ridiculous. Its always out of balance with just a few pieces and lack of water twisting everything in knots. Well 16 months after purchase here we are with a broken machine, we have a fried circuit board. Maytag has lost our business permanently.

I purchased a Maytag dishwasher Model # MDB4949SDE1 from Home Depot April 30th 2015. This dishwasher does not clean the dishes no matter what cycle you use. After 4 hours and 29 minutes I open the dishwasher to find residue on my so-called clean dishes. Every time I use it I have to re-wash or rinse the dishes by hand before I can put them away.I have spoken with Maytag on several occasions concerning this matter. I have used every detergent on the market. Maytag says you have to use jetdry, and liquid detergent which I did and it made no difference. The latest suggestion was that the water from my water heater was not hot enough which is set on 140 degrees. The customer service rep. ask me how far the water heater is from the dishwasher and I replied approximately 14 foot. She suggested I turn the faucet to my sink on before I turn the dishwasher on so that the hot water is present as soon as I turn it on. This also did not work. They sent a kid out today that turn the dishwasher on for five minutes empty and said well everything seems to be working properly. I dont know what to tell you, yet there is soap residue in the bottom of the dishwasher right now. Do not purchase this dishwasher. It does not clean the dishes. It just uses power and water.

Have had the top freezer Maytag refrigerator for several years now, and it has performed great. Exterior is easy to keep clean, and the interior shelves come out easy for washing. Three drawers for fruits, vegetables and meat/cheeses work out great, and keep those products at the correct temperatures. Settings for both freezer and refrigerator are easy to see and change, if needed. Would buy another Maytag unit. Easy slide out for cleaning coils behind the unit.

I purchased a new Maytag fridge apx 8 months ago (model# MFF2258VEW6). It has french doors and a bottom freezer and from day 1 it has constantly leaked water all over my kitchen floor. I started putting towels in front of it after my first slip and fall. I had the water line checked for the ice maker and it was fine. It continued leaking day after day. Then I started getting a lot of ice build up all over the drawers and on my frozen food, which became freezer burned and I only had the temp at 2. They have a warranty on it, so called the company and they brought me a loaner fridge of the same kind.. OMG this fridge is doing the same exact thing, even worse. I am disabled and fell last night again and my leg and foot is so swollen.. I really hurt myself and Im not going to let this company get away with this!! I called the company and told them and they are checking into what they can do with the refrigerator. After reading all the about the Maytag bottom fridge leaks and other problems, I refuse to get the same one again. If they do not do something, I promise I will before I get hurt again!

We purchased this oven (MER8880AS) as part of a package during remodeling in 2012. I was particularly interested in the bridge element, and in fact, its about the only part of the range Im satisfied with. Our first problem arose when we began using the range in 2013, and I got cut on a sharp edge while opening the storage drawer under the range. We contacted customer service, got a prompt and concerned response, and shortly after, a visit from a technician. Heres where it started to go south: the technician insisted that design as fine and that we were reaching too far into the drawer to open it. He left, saying basically not a Maytag problem and the customer service agent, who had promised to call after the visit, never responded to our calls. Fortunately, we have a good hardware store nearby and my husband and their staff came up with a solution.Burners and oven work okay, though with slower response time than other electric ranges Ive used. Convection feature seems ineffective on this range - I hardly use it anymore, though do use it all the time on my other range. The absolutely worst feature of this range is the Aqua Lift Cleaning System. This is a hoax by Maytag, marketed under the guise of an environmentally friendly system. It does not work, and pre-cleaning doesnt improve the outcome as only portions of oven that are clean are the ones pre-cleaned! If you like to cook and bake, do not buy this range!! Based on this experience, I will never buy another Maytag product, and though Im of the school that expects major appliances to last a long time, I can hardly wait to replace this range!

We bought a new Maytag dishwasher MDB7609 as part of the 2010 recall. Within the first twelve months the black skirt at the bottom of the door collapsed to the floor. It was in small pieces and brittle as though exposed to excess heat. The repairman fixed it free but made the point it was not covered under warranty. Next the heated dry cycle baked the water onto the dishes forming a white crusty layer. We have a water softener that works very well. We stopped using heated dry because it is too hot. Last night before bed, I was standing in the kitchen and I smelled something burning. My wife had mistakenly programmed heated dry into the cycle. Obviously this dishwasher is as much a fire hazard as the one it replaced but no recall has been issued yet.

Quiet, well priced and reliable technology which makes owning this dishwasher an easy buying and owning experience. Having the brand backed with great reliability and if needed excellent service makes the buying decision easy for the consumer.

I bought my fridge (Maytag French Door Fridge MFF2258VEW) in September 2009. It took forever to get it and when it was delivered, the door was dented so I had to wait for a new door to be replaced. The fridge stopped cooling just before Thanksgiving 2011. I had to throw out a lot of food. It was the circuit board and that was covered under the warranty. I noticed a couple of months later that the freezer was freezing up again and was worried that the fridge would go out again and in February 2012, they came out again and it turned out that the freezer had been put back incorrectly and the freezer gasket didnt fit right and thus, the freezing up on the circuit board. Now it is May 21, 2012, and I came home for lunch to find the fridge not working again! I cant get anyone out to fix it until Wednesday, the 23rd. Now we are in warm weather and I just went to the store and had a full fridge. I still have the warranty and will for another 14 months. I think if this continues to happen and when the warranty is up, we will have to replace this fridge. I can tell you for sure that it will not be another Maytag! What a piece of junk!

We purchased this new set of Neptune Washer and dryer at Lowes, in Yakima Washington in 2004, and now discover that there is a class action lawsuit due to the problems associated with mold, the pump, the motherboard, etc. Our washer is making horrendous noises when it spins, and the motherboard barely works at all. I trusted Maytag and bought this set and a stackable set at the same time. Yes, I am angry and will never buy a Maytag or Whirlpool again.

What happened to the days of buying a washer/dryer and having them for years! To spend a thousand on each and have holes in the bellow causing dirty water to Empty on your floor. Not once replaced, not twice, 5 times!!! Now Im looking to buy another. Old school for me...

I bought a fridge from Home Depot. It was on sale and not a Maytag. Somehow they delivered a Maytag. I am over-the-top happy with my fridge. It keep things cold. It is roomy, It has separate temp controls for the freezer and fridge. The bright LED lighting is wonderful. It is energy efficient. It is easy to move around when I need to clean under it. It was delivered right away.

We bought a Maytag refrigerator less than two years ago because... its Maytag. Less than a year later we had five service calls. The refrigerator wasnt cold, the freezer was the temperature of the refrigerator and it took two months and two different repair companies to fix it. And now... yes, the same problem seems to be occurring. It was a leak that was supposed fix. Cant bear the idea of going through this all over again. NEVER again Maytag!!!

I bought our Maytag HE washer model #MVWC565FW back in July 2019 after having owned a Kenmore scratch and dent washer from Sears for approx 25 years, and in just one month of using it I knew it was a mistake. There are only 2 water levels - deep water (full tub) or practically no water (though there are a number of settings, there is no difference in water level, its just full drum or very very little water). The auto-sensor water level option is a joke - there is barely enough water to wash anything - its like going back hundreds of years to washing and beating your clothes on rocks. Items in the washer become so tangled it sometimes takes a while to detangle before placing in the dryer. Water stops filling the tub when lid is open - I can no longer wash and rinse delicates while the drum is filling. It took 3 calls w/ Customer Service to get an ADDITIONAL lid latch that I can use to trick the machine to thinking the lid is closed - I keep the actual lid open, then stick in the lid latch I bought - take it out when Im done hand rinsing. This also enabled to to view the washing in action - IT DOES NOTHING! Clothes stay in the same place as you placed them in the tub - they dont move, they dont wash - and I bought a washer with an agitator - that is in quotes because it is a misnomer with this brand! The wash cycles ARE SO LONG it takes all day to wash a few loads of laundry. Once you select a setting YOU CANNOT CHANGE IT - the washer empties and stops, then you have to start all over again - ENERGY AND WATER EFFICIENT...REALLY???? What a bunch of you know what! This is the most inflexible piece of junk I have ever had the displeasure of owning. I have to keep jugs of water on hand that I keep filling up to at least have a bit of water. When I called Cust. Svc. at the beginning telling them my experience - the person on the phone had nothing to contribute - they couldnt even tell me what cycles might fit my needs - they told me to go back to Home Depot and ask someone there! WORST APPLIANCE WORST COMPANY.

Although we have always had Maytags, this was the first time we purchased a front load washer. The Maytag Neptune washer smells and your clothes stink. We have purchased the most expensive laundry products, washed and rewashed clothes and have no other recourse but to buy new machines again. We will not be purchasing Maytag or Whirlpool. I would give it a minus 5 stars.

I’m so disappointed in this refrigerator! It does not keep a steady temperature. It’s only 3 years old and will not buy another Maytag. I do like the freezer on the bottom but it also does not keep a steady temperature.

Our range and oven are reliable and durable. Easy to clean and have lasted a long time. I do not regret spending a little extra money to have an appliance that has lasted a long time. The oven heats up at a standard rate. The self clean function is very thorough. I have a white set. I was worried they would stain with your typical spills that come along with cooking. However, They clean very easily.

Quiet, efficient and leave you with clean dishes & utensils at the end of its multicycle cycle. This unit can self-clean and is always beautiful with its shine finish stainless steel interior. This unit can be installed by any user as it comes with everything one will need to complete the installation.

I purchased a Maytag commercial residential washer in late 2018, supposed to have a warranty for at least 5 years. We are in California and I was told that there was only one facility that could come two weeks later. I removed the front panel to have it ready for service tech, who on the first visit kept saying he did not know what the problem was, and left telling me he would order parts. After Christmas, I could not get in touch with service so again called Maytag. Service was supposed to come out on the 30th.After waiting almost 3 hours, he called to tell me he did not have the parts. Also, this repair tech treated me very bad since I removed the front panel which I thought I was being nice. He called me back on the 30th, said someone gave him a part, and came. All he did was remove control panel, lost the start button and told me it worked without checking it at all. He was rushing to another appointment so I tried to start it and it still had the original issue, which was slow agitator and a rubbing/grinding sound. Now, after he did something with control panel it had a clicking sound. I immediately called corporate and was told when he came back, which has now been over a month with no washer, that he would be with a senior technician.January 5th I waited all afternoon and he called and said he was not coming and that my whole washer would have to be rebuilt. He never replaced the parts on previous invoices I received, and I filed a complaint with the BBB. Now they are completely lying. Technician trying to say I had the control panel apart which is not true, and does not match up with the invoices I received. They are telling me my warranty is voided! Its been a month and a half. I was treated rudely from the beginning and now I am obviously being retaliated against. I have 3 kids, two with severe medical problems and have put so many hours into calling with all these issues.I had another service place come out and he removed the agitator and the transmission shaft/drive motor is rusted out, as well as the parts he said he replaced are worn and definitely not new. For this company to come back after all this time and say I did this, when I have the original invoice that clearly states otherwise is absolutely the worst service ever.I bought this machine thinking it would last, and now have to deal with all this. I have nerve damage and it is very difficult to take all the laundry for a family of 5 to do at laundromat. They refused to send someone else out, where they could easily have seen this repair tech never did what he said, and was unable to diagnose and fix the issue. Its appalling to me that this is how they treat customers. Laura ** at corporate is the one saying warranty is voided. The machine looks brand new as it has always been taken care of. They should be ashamed of themselves. Apparently, this is the standard a lot of times with people trying to get things serviced under a Manufacturer warranty!

Purchased a Maytag fridge April of 2012. Within a few months the freezer was not keeping the food cold enough. I had a lot of food loss. I called Home Depot and they refused to give me a new fridge. They said to call the Mfg. That I did and all they did was send out a service man. This has been fixed 5 times for the same thing. The problem now is that the Extended warranty company refuse to repair it now that they know that it was a pre-existing condition that should have been taken care of under the Mfg. warranty. I paid 180.00 for an extended warranty that now is worthless. I just threw out roughly 200.00 worth of food. Now my lettuce is frozen, eggs are frozen. My husband is disabled and money is not plentiful. I dont know where to turn. Frustrated.

It was alright for a while. Then it started ripping up my clothes. The machine is not overloaded, enough water has been added but, when I take the clothes out they are torn. Not a good experience. I have seen several reviews on the Centennials, none of them good. What is the problem. I am hoping my experience gets resolved.

Washer has plenty of functions for me to was even my work clothes. These saves me money and time. Washer leaves clothes clean and you can even wash your blankets.

Our Maytag refrigerator was about a year old when we noticed rust on the edge of the stainless steel doors. I called Maytag and they were nice enough to replace the doors even though the warranty had expired by their standards. Keep in mind, the warranty starts when you purchase the product, not when you install it. We ordered our appliances from Lowes well in advance of our kitchen remodel so we would have them when we needed them. The time our appliances sat in Lowes warehouse used up two months of our warranty.Now, the new stainless steel doors are rusting and they are refusing to do any thing about it. Should stainless steel rust? Maytag doesnt seem to care whether their product performs the way they should. Its all about the warranty. Once the warranty lapses, they could care less whether their product blows up. Thats the customers problem. Whatever happened to building a quality product that lasted and customers bought for generations? Obviously, thats a thing of the past.My goal in writing this is to make consumers aware of appliance warranties. When I spoke to Lucas, a Maytag customer service supervisor, he informed me their products offered no warranty on the finish of the product. So, according to Lucas, the finish on your brand new Maytag appliance could flake off like dandruff and its your problem regardless whether its a manufacturing defect or not. Remember, buyer beware!

I purchased a Maytag dishwasher because they are supposed to be known to be a good brand. But my dishwasher is 3 years old and it started rusting around a steam vent on the outside of the door! This issue has been ongoing but as Ive been busy, I havent had the time to address the problem with Maytag since its out of warranty anyway. But I feel like this should not be a warranty issue to begin with, it should be a recall issue. I had a plumber look at this, and he said that it was caused because the vent was not properly sealed during manufacturing. Now it looks as though mold spores are growing inside the steam vent! Maytag will not stand behind their product, so why should I invest anymore money into it?! I would rather purchase another dishwasher (OTHER THAN THIS BRAND) than dump another penny into this garbage dishwasher!

Model MDB4949SDZ0. 7/10/2018 Purchased from Costco. 7/23/2018 Installed by company arranged by Costco. 6/18/2019 A burning smell was coming from front control panel area of dishwasher when it was turned on. 6/25/2019 & 7/3/2019 Repair technician came to fix but could not find anything wrong so burning smell continued whenever dishwasher was one hour into cycle. 7/12/2019 Repair tech changed out front control panel because burning smell was still coming from handle area. 8/9/2019 Dishwasher does not drain completely when wash cycle is complete. Sometimes there is sudsy water left, sometimes it is clear. The water level is above the heating element at bottom of dishwasher.We only run the machine 2-3 times a week and have been using different cycles to see if the draining issue is with one cycle or all of them. No matter which cycle is used, water remains at the bottom of the dishwasher above the heating element. This seems like way too much residual water. Repair technician is scheduled to come for the 4th time to look at dishwasher but we just received a message that we will have to pay $129 service fee because dishwasher is now out of warranty. Maytag, fool me once, shame on you. Fool me twice, shame on me. Therefore, know that we will not be purchasing a Maytag product ever again.

Fifteen months after purchase of the top load washer, we have had to call in repair. The lid lock and sensor have went out on the machine and the repair costs are equal to the purchase of the machine. Whether the consumer has an extended warranty or not, this is unreasonable. So hear this Maytag, the CONSUMERS will invest elsewhere when delivered cheap merchandise like this even if it is Made in the USA as you wish to tout in order to bait the consumer for their money instead of providing superior quality American products. This consumer is sending this machine out the door.

I could not get parts for Maytag Model MHWE200XW00 Type 832A as the Whirlpool does not provide after sales service. I purchased the new washer in 2010 and lasted for just 4 years. I believe they guarantee supply of spare parts (Inner Basket, Outer Tub and Rubber Boot) for 10 years and more.

Maytag Dishwasher Model # MDB7749SBM1. What a piece of JUNK! Purchased in June 2013. Control panel went out six months later! June 2014 Control panel BAD again (#2). March 2015 another Control panel replaced (#3). Thank God for Home Depots extended warranty! October 2019.... Control panel needs replacing!

I have ALWAYS bought MAYTAG since the 1970s. But MAYTAG is no more. Whirlpool bought them out. I have an HE (first mistake)... HE... will go away just like low flow toilets did!!! You cannot wash clothes in 4 of water. I bought a top loading Brazos XL for $1100 (second mistake)... Have had it just over a year! I should have returned it but did not. Huge mistake (#3)... Repairman told me to get rid of it as fast as I can. Will eat me up in repairs. Now needs repair again for another NEW issue... The fill sensor does not tell the machine to load the proper amount of water. Now I cannot clean washer, tried three times last night. I am beyond upset. Repairman said buy GE! You can bet it will NOT be High Efficiency!!!!!

Love my washing machine. It is so big I need a step stool to reach down to the bottom. It cleans my wash well and I have dirty clothes. I hang my clothes on the line outdoors. My clothes have never looked and smell so good.

We just purchased a house with new appliances. They are Maytag. When I use my stove the oven heats. I have no idea why. I wondered if anyone else has had this problem. When I turn it off it turned off but it turns back on when the oven is on.

Our washing machine is 3 years old. About a year ago we started to see hairline cracks on the plastic lid in the bottom corners by the hinges. These have now become huge and pieces of plastic are breaking off every time we do a load of laundry. Maytag (under the Whirlpool brand) will not replace the lid for us. We paid $130 for a tech to come out and confirm what we already knew - that we need a new lid. And now the parts and labor will cost over $550. We have called customer service several times and spoken to a supervisor and the best they can offer us is to pay for the part which still leaves us to pay over $400 out of pocket to repair a $600 washing machine. This seems to be a common problem and is all over Google, yet Maytag is not willing to help their customers.

My Maytag 3000 series washer had to be worked on right after we purchased it. Now it stinks and is leaking. Repairs are going to be over 300 dollars. A part wore out. It should have lasted longer and why does the front loading washer stink. There is no door to open to clean the filter.

First off. Maytag customer service is horrible. I purchased a Maytag washer & used it 8 time. It now doesnt rinse the soap out of my clothing or even clean anything. The washer isnt broken because thousands of other people with the same exact washer have written negative reviews everywhere online. The washer needs to be recalled & never sold again. Maytag is making people SICK and they dont care. My whole family had skin irritation because we didnt realize our new washer wasnt rinsing.

We have had Maytag washers in the past, and they always worked well and were reliable. Not so with the Bravos washing machine. It is by far the worst excuse for a washing machine weve ever used. It does NOT clean clothes. It merely ingrains the dirt more into fabric. In four years, we have complained repeatedly to Maytag to try and get some kind of remedy to no avail. Maytag is simply not interested in standing behind their product. So now, after two generations, they have lost us as customers forever and we are telling anyone who will listen; DO NOT BUY A MAYTAG WASHER. They are terrible and not what they once were.

We have had this machine for too long. It starts banging and making tremendous amounts of noise. We have balanced it and tried loading it in different ways but when it starts to spin it apparently tries to even the load somehow that results in very loud noises and movement of the washer in the laundry room. Terrible machine. If we could afford it we would trash this one in a heartbeat and buy a different brand.

We purchased a Maytag Commercial Technology washer from Lowes. After having the washer for only 3 months, the drum failed, an entire load of clothes was turned black with oil, and my washer was out of service for months. The drum had to be replaced. They did not offer me a replacement. I was just without a washer. They couldnt get the parts because of supply issues created by Covid. I was offered a 2-year additional warranty which should have carried me through 2022. Last week, I called to use the warranty - service was scheduled (and I was told that I did indeed have a warranty by the service team.) I was then told by the repair team that I was out of warranty. Maytags notes show I was only offered a 1 year additional warranty. I talked with Management at Maytag/Whirlpool - they will do nothing for me. Shame on me for not getting that in writing. Shame on Whirlpool/Maytag for lying to me. The washer has been a nightmare! Dont buy one.

I purchased a Maytag electric slide in stove, in stainless steel. The aqua clean is a joke, ran it for three cycles after cooking one roast and it does not work. Then to add insult to injury I had to get on my knees using a turkey baster to remove what was left of the two cups of water. The finish on the front is coming off. Not at all what I expected from a 1500.00 range. Poor quality. Now there is the sound of a fan running and I am not using convection.

Our first (and last) experience buying anything made by Whirlpool. I bought a matching Maytag Series 2000 washer and dryer in February 2011. By July, the washer was at 747 take-off noise level when hitting the spin cycle. I called Whirlpool, who directed me to their local repair firm. I called them on August 2nd and had a service rep visit on August 9th. He looked a 30-second look and advised that the bearing assembly was shot and that the spin basket required replacing.

I have never been so disappointed in purchasing an appliance for my home. The Maytag Bravo XL large capacity top loader, has never worked properly, and I have many ruined pieces of clothing. Although it has a very large capacity, the water barely fills to a 1/4, and clothes are sticking out of the water, while they are supposed to be submerged/being washed IN the water. Clothes come out of the washer smelling foul. WORST WASHING MACHINE EVER.

I purchased this washer because it has a large, stainless steel drum, and a deep wash setting. My laundry comes out very clean, and I do not need to run it through an extra rinse cycle. The sensor determines what size load I put in, so I am not wasting water on small loads. Overall, I am very happy with my washer. I purchased it about six months ago.

A lot of repairs in 6 years from belts. It leaks water around seal on door. Only part of the cycles work. I would not recommend the Maytag washer to anyone. When I got it I expected or hoped it would last 10 years or more.

Purchased a Maytag OTR microwave in May of 2017. Started having issues with the Open/Close Door malfunction by September. Repair came out and essentially told us to keep opening and closing until it worked. It is January 2018 and the issue has gotten worse. My question is, since Maytag is keenly aware of the problem and has for years, based on other reviewers on here, why hasnt a class action lawsuit been filed? These appliances are expensive and it sounds like many of us have been taken to the cleaners!

Very dissatisfied with Maytag Washer Mod MVWB835DW0. This Large Capacity machine does not adequately clean a large capacity of clothes. In order to get a half decent wash performance from this machine, fill the machine only 1/4 full. Even using the recommended manual, I was very dissatisfied with the way my clothes looked after washing them with this machine. While I have been unhappy with the performance of this machine since purchasing it. What motivated me to leave this review is when my pants had the same sand debris on them after the wash as they had before the wash. I will be looking for a new machine this weekend. IT WILL HAVE AN AGITATOR TOWER!

DISHWASHER MDB7749AWM - We purchased this dishwasher from Home Depot on 10/15/2011 for $630.00 for my birthday and yesterday the start button stopped working (cycle lights still work). We went online to look for more troubleshooting options and we found lots of complaints about faulty control panels. Sounds like thats what we have. VERY disappointed in Maytag for not correcting known issue. My dishwasher is only 3.5 years old and there are only 2 adults in our home. We run the dishwasher 1 to 2 times per week meaning this Maytag dishwasher will only last for about 200 wash cycles. Shame on you Maytag!

Bought this Maytag microwave mmv 4205ds March 2016. Have had open/close problems five times in 3 years. Unit replaced under warranty once. Now out of warranty. No need to mention inconveniences we’ve been through. Whirlpool-Maytag obviously have done nothing to correct this problem. I will never buy any of their product again. Wanted to give them ‘0’ stars but program won’t allow me.

Im so mad over my new purchase on the XL Bravo washer and dryer and Home Depot will not return. I have 3 kids and a hard working husband. My clothes do not come out clean no matter what cycle I use. It takes forever just to wash one load. If you spill something on your clothes and it dries crusty it will come out of the washer crusty. I want to cry. So much money wasted and cant get our money back. Would never recommend a washer without an agitator. Towels come out soaking wet, and dont spin dry if heavy...forget washing a blanket. 4th day using the dryer and now there is no heat. What was I thinking!! So mad and sad too!

We purchased a Maytag Jetclean Plus Dishwasher in June 2013. It worked well enough initially. We bought it because it had a large capacity and built in disposal. By August 2014, just after the warranty expired, the front panel gave out. To have someone even look at it cost $150. By following instructions from internet discussion groups by other people facing similar issues, we were able to get it to run in random mode. Programs were no longer indicated or selectable but dishes generally still got cleaned. Two months later a wheel fell off the premium rack glides. Finally after about 2 years of use, the dishwasher finally gave up altogether. At this point the stainless steel tub is no longer stainless. The entire device has worn poorly and looks shoddily made. This is the worst use of $900 I have ever made, and what tweaks me the most is Maytags attitude and their ludicrous warranty that barely lasts out the weakest link in the device.

I have a Maytag Range that I bought new and installed 6-1/2 yrs ago for over $1200.00. I am single so I rarely use the ovens. The upper over I use maybe 1-2 times a month and the lower oven I may use once a month. The night of 3/7/2016, I used the cleaning cycle set on medium for both ovens. Yesterday, when I went to wipe the ovens down, I found the lower heating elements, on both ovens, had snapped. The top ovens lower bracket had broken in 2 places, the first break is about 2 from the connection, on the right side leaving about an 7 gap. The lower ovens element had broken in only one place about 2 from where it connects into the back of the oven. This has to be a flaw in the either the design or the material. In the 45 yrs that I have been using ovens and stoves, my last stove was over 35 yrs. old, I have never had a heating element break. While I can understand a break at the connection, I can see no reason that the it would break in the center of one side on both lower elements in the same oven. I also noticed that lower heating elements are a much small gauge than the top which I find strange.The other issue with the stove is the seals around the windows are not tight. I noticed dust was inside the two glass panes. The rubber seals were sunk down into the door, but Maytag said it was not their problem that I must have done something. When I remodeled my kitchen, I bought all Maytag products: 1.H20 Frig - The electronic panel went out after 3 months and had to be replaced. Manufacturing Defect - When the repairmen came to fix it, he told me to call Maytag which I did. They refused to pay for the repair because I called a repairman first, even though the business was Maytag certified. Even though I said I would cancel the service call they said because I had made the appt. and they recommended I call Maytag, they would not cover the repair. 2. Stainless Steel Dishwasher (Cost over $700.00) - Motor went out after 3 yrs. 3. Microwave/Convection Oven (above the stove)- Convection light out after 4 months. The replacements are not inexpensive.One other complaint I have is when I bought all my large kitchen appliance Maytag had a $600.00 rebate offer. Even though I mailed all the required documents to the company over 2 months before the rebate ended, I never received my rebate. The explanation I received was that the center that received my documents delayed forwarding them to the proper department that processed rebates and they were received after the offer ended. When I questioned the legality of the practice, I was told that this was all explained in the Terms and Conditions (ie: small print).

I researched gas ranges for a few months before choosing our Maytag gas range - it was on sale when we ordered it and it arrived within a couple of weeks. We wanted to buy local and were successful with price matching the sale price. I would recommend this range as it functions great and we totally love the larger oven door.

My Maytag top loading washer, 4 years old, stopped working in the middle of a wash cycle. Registered Maytag repairman did a diagnosis and finally identified the problem with the control board. The cost of the control board would have cost almost as much as the original wash machine especially since I had to pay for the current service call and labor (to diagnose the problem). After having read a number of other reviews from dissatisfied customers, I will not buy another Maytag product. I was under the impression that Maytag produced a superior appliance but was disappointed by this experience.

I purchased a Maytag Top Loader Washer MVWX500XL last May 2011 from Home Depot to replaced our 15-year old GE washing machine. Two weeks ago, it started making horrible noise like a jet engine taking off during spin cycle. I called in the Maytag repairman and was told that the bearing is gone and it will cost $ 493.00 to repair it. He claims that the damage is caused by not using HE detergent exclusively and he refused to leave us a written estimate. We are only three adults in our household and we do our laundry once or twice a week. For this machine to be repaired only after 2 1/2 years of light service and for almost the same cost as a new one, I will never buy another Maytag/Whirlpool products ever again and I will encourage everyone the same.

It’s really quiet and it cleans the dishes, pots, glasses on just 1 cycle and I’ve had it loaded more than one time. I do use rinse aid and I do occasionally use dishwasher cleaner. I wouldn’t own angry other than a Maytag dishwasher. They last forever. The commercial about calling a Maytag service man is true! I’ve never had to call fior service! Well worth the money!

We purchased the Maytag Atlantis used (4 years old); it looked like new. When I opened the lid, I noticed a terrible smell like some left the clothes in the washer for days. I used white vinegar, baking soda, bleach, anything to try and get rid of the smell. Nothing worked. Finally, my husband took out the agitator and then the drum. Inside and around the drum was lint from all the years of washing clothes. He scraped it all off and bleached it and put it back together and it was okay for a while. It now smells again and I am afraid we will have to keep doing this or our clothes will always smell. I also leave the lid open after a wash so Im not attacked by the smell when we open it. I also had the Maytag Neptune front loader years ago, and the water pooled by the gasket on the door. That smelled too! We will be redoing our laundry area soon and will be shopping for a new washer and dryer. It will not be a Maytag!

I purchased a Maytag Neptune Washer and Dryer at Home Depot for over $900. Within months, the board went out. The repairman said that they didnt even know how to fix it yet - no training. The board was out again. This time, it was not under warranty. The repair costs $779 including part and labor. There were numerous other little problems along the way that we did repair, but now, forget it.

Dinner ruined again... I bought all brand new Maytag stove MERS755RAW, I can only use one area and that has cant move them, the racks fall through. I have burned myself time after time when attempting to pull the racks in or out. Friends arrived and when we pulled cooked dinner out the rack fell through and it was so hot I could not hold it causing the entire dinner to come crashing down and spilling everywhere. I along with my family cannot use it again. Can anyone assist or make a recommendation? New racks do not work as it appears that oven has expanded and the dimension have changed. Do they have a recall or safety repair bulletin?

Received this Maytag dishwasher model MDW7749SBW1 as a gift from my son in June 2013 when my old dishwasher finally quit. January 2014, the soap/rinse aid dispenser did not work. Called Maytag and they sent repairman who replaced the part. Still did not work so repairman said another part was not communicating with the dispenser so he replaced that part. Worked fine. No charge since it was under warranty. Now its July 2014 and the touch panel doesnt work. Called for repair and was told since it is out of warranty, it will cost about $350 to repair. I called Maytag about this and said that I had a defective appliance. I was told that since I didnt buy the extended warranty, there was nothing they could do. I mentioned my last Maytag lasted 25 years and had only two minor repairs so I didnt see any reason to buy an extended warranty. I thought I was buying a good product. I was told shed register my complaint. Waiting for my repairman to come out tomorrow and see what he can do. I also have a Maytag stove. Wonder how long that will last?

The washer does not wash properly at all. There is not enough water. The clothes come out covered in lint and still soiled. MOD: MVWX655DWI, SER: C63142093. DO NOT PURCHASE THIS PRODUCT unless you want a ton of frustration!

After researching the top-rated washing machine in consumer reports, we decided to spend the extra cash ($930) and buy the top-rated machine. Spending almost double on a high end machine, you would expect this machine to last longer than three years. The motherboard needs to be replaced because it gets stuck on a UL code near the end of the cycle. Now, we have had two people come try to fix it, and they said to trash it and buy a new one. Only three years! If I had paid $300, I wouldnt be so upset, but that was a total waste of money for it to last less than any machine Ive ever had. How is a consumer supposed to know what a good washing machine is if they spend extra cash for the top-rated machine and that one is still bad? The company should replace something like a motherboard that goes faulty when it had nothing to do with use. So unfair and frustrating.

Both the microwave and French door fridge handles are crap. The microwave has completely broken and the fridge is very loose and will soon break, Im sure. Both are less than 5 years old. I will never buy Maytag again.

Oven was purchased and put in May 2014. I have not be able to use. The oven temperature is off. If the oven is used at 500 degrees the temperature is really 900. I thought I had a gas leak because I got a bad headache because of the smell. The gas co told me to get a repair person to look at it. Maytag has been horrible to deal with. I have taken 3 separate days off trying to get it fixed. The last Maytag repair man had the nerve to ask me where the gas line was. He shut the wrong off and had a gas leak in my house. I had to open all windows. He was supposed to come back the next day. He did not and I received no calls. I have paid for an oven that is dangerous that I cannot use. I feel Im being treated this way because I am an older woman. I will never buy another Maytag.

We purchased a $700 Maytag range 2 years ago and recently the oven did not work. After a Maytag authorized tech came out and checked the unit, he proclaimed the circuit board was bad and needed to be replaced. Since these ovens only have a 1-year warranty - regardless of the price you pay - he said it would be over $450 to repair it. When I asked why so expensive, he stated that they dont price the parts - Maytag does. I decided I could buy a new range for that price and get one with a warranty so I passed. I then decided to contact Maytag because I was very disappointed that such a reputable brand would prove so faulty. After writing a very polite letter and emailing customer service, they replied with a pack of lies. They stated that they have no control in what the service company charges for parts and failed to offer any assistance. They did not offer any solution except to say, Sorry. Well, you can bet that I have already spread the word to all my friends and associates about this experience and my Facebook page lit up with comments after I posted it. I will never buy another Maytag product and will make it my mission to spread the word. I had a similar issue with my brand new HP laptop but after contacting them, they immediately reached out to me and offered to pay for part of the repair!! Thats how you take care of your customers.

We Purchased a Maytag gas oven/stove three years ago believing it to be the quality of the Maytag of yesteryear, Boy have we been disappointed! When Whirlpool Corp. bought out Maytag several years ago they continued using the Maytag name only.. The quality is now less than substandard, It is a cheaply built piece of crap.. We would sell it in a garage sale and replace it with a quality stove/oven but we dont want anyone else to have to deal with this piece of junk! It will soon go to the landfill!!!