We had 10 year old Kenmore units in the past that were much better and worked faster at both cleaning and drying. We prefer a washer with a agitator and top load. The dryer is preferred to be gas. Both the Maytag washer and dryer we have need constant repairs. Washer for control panel repairs, and dryer for false heat sensing problems. Now they say not to use dryer anti-wrinkle sheets. The washer needs less sheets put in at a time to rinse better. It is a agitator less model.

We have had this refrigerator since January 2011. All was OK for 18 months. Then the lid to the deli drawer fell off, the plastic bar that holds the two drawers up broke (weve had to use roof shingles to prop them up) and another one of the plastic pieces crumbled. Now the ice maker wont work and the refrigerator makes a loud ticking noise. There are only two older adults here and we have not treated this appliance roughly. After reading all the complaints on this site, Im wondering if any of it is worth fixing. My GE refrigerator worked for almost 20 years.

Leaked and leaked, spent hundreds on never ending problems from day one. No support from Maytag. I was told by Sears salesman it was the best you could buy. Our old washer lasted 30 years. This one never worked right - dead at 5 years. Shame on Maytag.

Big mistake. Worst purchase ever!! These high-efficiency washers (Maytag Washer Bravos XL) are the worst especially this one! I wash and wipe down the washer drum more than I was my clothes. I purchased it because it had a huge drum so I can wash my blankets and comforters. This washer leaves soap scum marks/residue on clothes and leaves it on the drum as well. I basically have to wash my clothes twice once with soap and then run again with just wash and rinse without soap, you tell me how efficient is that! Why not make a washer that put more water so the clothes can get washed properly. Dont worry about my water and electric bill. MAKE A WASHER THAT WORKS!I called customer service she asked me if I use the deep water, now you tell me why am I going to use the deep water, if that is the only way the washer is going to clean the clothes then do NOT give me 11 other options the washer to use. ONLY HAVE DEEP WASH OPTION. I dont care about the bells and whistles, I do not need a different tune when I turn it on and a different tune when its done washing my clothes. Make the washer the way it used to be WASHES CLOTHES WITH WATER AND LOTS OF IT. I will pay my bill not to worry. So I called customer service all they said was they will document my call! Well... like thats going to do me any good while I am stuck with your POS washer!

I was repairing this Maytag Maxima washer and was almost electrocuted. I simply grabbed the wrong screws which were too long for the door switch, one screw went through into the open/close switch and contacted voltage, thus causing a direct short to the chassis and me. It also damaged my control board (the most expensive one in the industry), now Im out an extra $220 because Whirlpool made an engineering error. A screw should not be located so close (millimeters) to a voltage source where a simple mindless mistake could cause electrocution and possibly death. As for the washers operation, the drain pump failed after just two years, it sometimes leaks water out the front because debris gets into the boot drain back holes. It smells like mildew even though we leave the door open, my clothes stink, Affresh is costly and really doesnt help much. It does a decent job of cleaning, not as good as the old top loaders but it saves water. I think next tax return time this machine goes up for sale and we get a better machine.

We bought this Maytag Bravos XL machine in Sept 2016. It has never cleaned the clothes properly, you cant even tell they have been washed! It also shakes a lot. In January it shook so much it knocked a hose off, flooded my kitchen and downstairs bedroom. Home insurance had to pay to replace the kitchen floor and downstairs ceiling. We contacted Maytag. They said they dont have a repair person in our area. Home Depot wont take it back. We are stuck with no workable machine. We have to go to the laundromat and pay 70 a week for laundry, plus the time, and we are out all the money. We paid Home Depot (thousands) for a washer and matching dryer. Plus all the takeout we had to order while they repaired the kitchen, but the strain of this whole thing is ridiculous.

My daughter purchased this washer and matching dryer as a set from Lowes about 4 years ago. It was one of the few with an agitator and that is what she wanted. After using the washer for the first time she was very disappointed to find that the shortest cycle took over an hour and that the locking lid feature couldnt be bypassed. A few weeks ago the washer began gushing water onto the floor which flooded the basement below. She had purchased an extended warranty which was due to expire the following week.She called Lowes and scheduled a repairman. He finally came 2 weeks later and used the Internet to help him diagnose the problem!!! We could have done that. He decided that the control panel was only allowing the agitator to turn in one direction during the wash cycle. So essentially it was spinning a tub full of clothes and water causing lots of water to overflow the tub onto the floor. Needless-to-say he had to order a part and cant return for over 2 weeks to install it. IF this is even the problem! He also said he couldnt disable the locking lid feature! If my daughter had been able to open the lid when the problem started she would have known more about it.We are thankful her machine was under warranty but she will have been without a machine for almost 2 months when and if it is fixed. This is completely unsatisfactory for a gently used 4 year old washer. The dryer takes forever to dry also. If you are buying Maytag based on how long your grandmothers machine lasted, you will be disappointed! This washer caused so much damage we had to file a homeowners insurance claim!

Maytag Model #MBR2258XES refrigerator purchased May 2014 from Home Depot. Problem #1: Freezing in refrigerator compartment (frozen vegetables). Problem #2: Water leakage on floor from defrost. Wood floor is/has expanded and may now be ruined. This model is now discontinued. Looking into contacting an attorney.

Weve always bought Maytag, but this is our last time. The washer is just a piece of junk. It uses very little water and the agitator does not work. The clothes end up at the bottom in a ball. The water level is so low sometimes my clothes arent even wet. As I type this it has been stuck in the rinse cycle for 2 hours. It just keeps repeating. Maytag should have to replace everyone of the BRAVOS XL washers. I am no longer a loyal customer. I might as well go down to the river and beat my clothes on a rock. At least they would be cleaner. Shame on you Maytag!!!

I bought a Maytag range (MET-8775) last year, because my wife loves to bake and wanted the double oven. The oven never did brown properly, despite trying different temperatures and cookware. So, I called the 1-800 number in the manual. I was told they would have a technician come out and check it, and they assured me it was under warranty. The technician arrived, and since it was close to the end of the warranty period, I showed him the receipt for purchase. I got another assurance that this visit was covered by the warranty, before anything was actually done. Well, he checked it out and eventually calibrated the temperature. That helped a little, but still, it doesnt brown very well. About a month later, I got an invoice from the service company that dispatched the tech telling me Maytag will not cover the visit under warranty. After a long call with Maytag (now Whirlpool, I believe), I was told that since the calibration instructions were in the manual, it wasnt covered! Well, why wasnt the thing calibrated to begin with? And your average customer is expected to have an accurate thermometer/gauge to set it and know whether the temp is off or not? Why was I told twice that it would be covered? If either the lady on the 1-800 line or the tech who came had told me this wasnt covered, I would have argued a case right then. As it turned out, I had no choice but to get billed for something I was assured was covered. And as I said, it still doesnt brown right; and we had tried different temperatures before. We are preparing a major kitchen remodel, and its hard to believe that Maytag/Whirlpool would so thoroughly piss off a customer and potential future customer over an $80.00 service call.

It's mounted above the stove, ten years old and still looks & operates like brand new. Have never had a problem with it and it's used almost daily. From heating up food to making dinner & popcorn. This is the longest lasting microwave I've ever purchased. Maytag made a great product.

Purchased my 1st brand new washing machine almost 3 years ago, a Maytag Centennial Washer for a little more than $600.00. Now it needs over $400.00 worth of repairs to get it working. Theres a reason the Maytag repair guy has nothing to do. Its because their products cant be repaired and are disposable. 25 years ago we bought our first washing machine that was used. It lasted for 22 years before it died. Maytag cant make a product that can last for 3. Also got stuck with a $65.00 service fee for them to tell me its broke and not worth fixing. Do yourself a favor and steer clear of their products.

I have the Maytag Direct Drive Motor washing & dryer set the is supposed to be “commercial technology.” The washer is supposed to keep wet clothes fresh if they don’t make it to the dryer right away. After 2 years, I disagree in that it offers no better outcome than the much older machine I replaced. Furthermore the dryer cuts off leaving my clothes damp every single time, which I cannot stand. It leaves my clothes to wrinkle terribly and damp to stink if I do not collect them fast. I honestly wish I still had my old set. All the new features simply fail to measure up not to mention over complicate and add expense to repairs.

I bought this washing machine approximately two and a half years ago. I replaced the agitating wash plate three times. After several months, the wash plate will start free spinning from the gear and will spin like a top. It has to be replaced at $140.00 plus the service call. When it was working, it doesnt clean the clothes well. I contacted Maytag numerous times about this problem and they basically gave me a tough luck answer. I just went purchased a old style machine with a tall agitator that will clean like its suppose to. Its a shame Maytag has no compassion to try and compensate customers for the expenses. I also contacted Whirlpool which took over Maytag. My rating is a negative five.

Apparently the Maytag Bravos HE top loading washer is poorly designed. We have sparingly used this washer for approx 3 years and it began to make a horrible noise in the spin cycle and then to give us UL error codes. After searching on the internet we discovered that the seal around the main spin shaft and the bearings were bad. Inspection under the machine revealed a terrible rust and grease spot and splatters of rust and grease on underside of unit. This is a typical problem and this machine should have been recalled or at the very least repaired by Maytag for little if any cost. They now make a kit to fix this problem, but this should not happen after only 2-4 years of use on a $700+ machine. Very, very disappointed with Maytag! Customer service, of course, offered us nothing as pathetic 1 year warranty was expired. Ten year on the tub, like anything will go wrong with that.

Maytag is a reputable brand name for a washer & dryer. However, they have done very well in the oven/range industry as well! I own a oven/range for over 4 years now and it works great???! Food is cooked to perfection and cleaning???? And self-cleaning is a snap!

Brand New 2017 Maytag Dishwasher MOB8959SFZ4 - The first time we used it it leaked from the door. I called the plumber back to make sure it was level and lined up properly and it was. Called the dealer, they sent a technician who sent away for a new latching mechanism. 3 weeks later the parts showed up. Technician installed them ran it through empty and no leaks problem solved? Nope. So I loaded it up and ran it again and it leaked. Called the dealer back but the technician is away on vacation.They suggested that the top rack might be pushing against the door for some reason when it is loaded so I removed everything from the dishwasher and ran it through again but it leaked again.Its something to do with the door not latching properly and it doesnt have a lever that locks like the old ones did. Its such a flimsy product. It baffles me that importers are getting away with bringing this crap into the country. Im now in week 5 with a brand new dishwasher that doesnt work. Maybe thats why its known for being one of the quietest dishwashers on the market.

The refrigerator is barely over two years old and the bottom pan fills with water, freezes and leaks out onto floor. Is a very common problem with these refrigerators and Maytag is happy to pay for the new part to fix it, but will not pay for any person to fix it. They have known this is a problem for a while, but will do nothing to fix it. They clearly do not stand behind their product with a known ongoing problem. The Maytag repairman is no longer not busy. Will never buy a Maytag appliance again! Will take the new part and fix it ourselves.

Our Maytag dishwasher was purchased new in December 2013. Less than a year later, the control panel needed to be completely replaced. While this first repair was under warranty, the next Complete control panel replacement was not. 8 months later, the same problem and this time the expense of over $300 is out of pocket! The company had no comment and was of no help at all with my customer complaint call. I wish I listened to the warning reviews and never bought a Maytag. Do not buy!

I bought this Maytag refrigerator model MF 12269FRB00. It is not, user friendly, meaning that condiments and small bottles just dont fit conveniently in any space, The biggest issue is the ice maker. The ice maker shoots ice out on each and every attempt. Every time you want ice you are guaranteed to have ice shoot out of your glass on to the floor. I often challenge my guests to get ice without the cubes shooting out of the glass. No one has ever won. Dont buy this piece of crap, unless you find humor in having ice on your floor every time. Shout out to Grays Appliance in Melrose for selling crap! I will never buy from them or Maytag again. To the engineers who designed this product, you suck too!

I am, was, a loyal Maytag owner. The Bravos design, center hub, catches the clothes and rips the material. Customer service will only state damaged material is not warrantied. So I now have a washer that in addition to washing clothes rips them.

Thank you all for taking the time to write these reviews. My only regret is that I am reading it now, I wish I would have read it before purchasing my own Maytag washer and dryer... I bought a Maytag MVC565FWI / YMEDC555DW1 washer and dryer duo in December 2018. I had some holes in my sons clothing, but thought maybe they were due to him being a boy of 17 year old in college, sitting all day... Also my dryer was barely drying.Called and had a 1st technician for the dryer issue. He said no wrong code and to try and clean the evacuation vent. As I am a renter, I contacted my owner to do so and he did. But I did not get to try the machine unfortunately since 5 days after the technicians visit, I was deploying to Africa. I am military and was deployed for 8 months. Upon me return, dryer still barely dries and HOLES in every load of laundry that I do. My sons and also my own clothing. This time, there is no mistaking articles that I put in came out with huge circular holes.A second visit with a technician is arranged, last Tuesday October 8th 2019. Still no codes are found. And technician suggests cleaning the conduct better. Again my owner does so. Again, up to 4 cycles of 60 min on High heat to dry articles. No economy on energy on these models! I have called Maytag today since no one has contacted me in a week for my wrecked clothing. To my request of having my appliances either replace or refunded, they say no. Policy is to send a technician. Again. After 2 visits of technical support, Maytag is sending me for a 3rd time a technician (at my cost if nothing is found again) to test the appliances. Since the technicians can not find a code on his machine, Maytag is telling me they will do nothing.I have a washer dryer that wrecks my clothing and does not dry them. (Also I feel like my clothing are never fresh scenting, I wonder how efficient they are with even the basic cleaning part..) I will have to put them in the garbage, because how can I sell them?! Talking to Maytag, is being treated like an infant that does not understand THEM, when in reality, they do not back their products at all. I feel left alone with brand new machines that have been used around 30 times in under 1 year, that I will have to through away in the dump and never ever buy from this company again. M.

The control panel of my dishwasher is malfunctioning. I looked this up online and ran into a recall for the heating element. Sure enough, my dishwasher is effected. I asked why I was not contacted. First they made up a story as to not having my contact information. This is simply not true, as I purchased the dishwasher directly from Maytag. Three years ago there was another recall and the heating element caused another problem so Maytag replaced my dishwasher.If a heating element overheats, it seems to me that a short-term affect could be overheating the control panel, causing it to malfunction. I read through a few recent complains and would also like to inquire about having this issue looked into by the Consumer Affairs.

Ice maker not making ice, lights on the temperature controller are all flashing, ice/water dispenser door continuously opens and closes, refrigerator and freezer both do not cool/freeze properly. I purchased a new main control and low voltage board at a total cost of $400 and replaced them to no avail. Nothing changed when electronic boards were replaced.

We have owned the dryer (Maytag Bravos) since Dec. 2010 and are now on our 4th service call. Upon the second delivery of the part that was ordered last week - we will be on the 5th service call. I finally asked Maytag if I could get a trade in since this dryer is obviously crap. They said they could only handle the problem at hand, which is the same problem over and over and over. The flywheel was left off all together. The pulley belt for the dryer pops off about every 4 to 6 months. Ridiculous. Its a crap dryer, dont buy one!

Our Maytag Dishwasher, Model MDB4949SDE2 was purchased May 14, 2016 at Home Depot for $470. It has performed perfectly until January 6, 2020, when a noise, loud enough to imitate grinding wheel, happened with every Start-Up attempt. An independent technician advised replacing the pump motor, thinking that perhaps some popcorn kernels had lodged in the system. (Kernels were cleaned out of the drain filter.)We operated the unit after he left, and the noise began to diminish, eventually disappearing altogether after several loads. Today, February 26, 2020, the same tech found that the large, upper impeller was clogged (not rinsing completely) with citrus seeds and VARIOUS METAL SHAVINGS & SMALL PIECES OF WHAT WOULD BE CHOPPER BLADES FROM THE INTERNAL GARBAGE DISPOSAL. After reading the Maytag Dishwasher problems experienced by others (with repeated control panel failure, burning wires, leaks, and house fires), I consider us lucky to have none of those. We will not run the unit at night, nor with an empty house. Next problem, we will buy a Chinese made dishwasher, like GE.

I purchased my Maytag 4 door refrigerator with the freezer at the bottom (model #MFX2570AEM) in December of 2012. A couple months ago it started leaking small amounts of water. I now notice that there is such a build-up of ice under the freezer drawer that it wont even close properly. I, like all the other consumers that have complained am fuming mad. I purchased the Maytag brand because of its great reputation for quality products. However, this is totally unacceptable that I should be having issues with this refrigerator less than 3 years later. Shame on you, Maytag!!!

During 2018 we purchased Maytag Bravos top loader to replace antique KitchenAid. Very dissatisfied at first, but luckily found the settings that makes my machine work very well on every cycle. First add 1/2 gallon of water to empty tub. Add detergent. Set controls at: Soil Level-Heavy; Wash temp - Warm; Main dial - Bulky Sheets; Extra Rinse - ON; Fabric Softner - OFF. Can now load full tub of clothes and more detergent if desired. Press start button and water covers it entirely. It works so well now, that I went from I hate it to I love it. Been going for two perfect months with no issues. Weird but true. Hope this helps you.

When we moved to a new home, we upgraded all the appliances, including the microwave. This was four years ago. When the first microwave stopped heating the food after two years, we thought it was a fluke and bought a brand new one, since fixing it would have cost more. Well, I should have gone with another brand. This is two Maytag microwave ovens in four years! We cannot believe that a company who enjoys such a good reputation can get away with such shoddy products!

I bought this machine about a year ago. It does not wash your clothes good. Stains nor smell does not come out. It makes this god awful noise that can be heard throughout the house... It suppose to save on your water and electric bill but no savings for me considering I have to wash items 2 or 3 times... I hate this washer and I paid a lot of money for nothing coz that’s what it does - nothing!!!

We lost our home in a tornado in 2005 and had to buy all new appliances. So, I bought a Maytag Neptune front load washer and dryer. It was my 1st ever. I will never buy another Maytag appliance again. Just at the end of the 5th year going into the 6th year, the bearings started to go. So, I checked with the place where we bought it and was told how expensive it would be to fix. It was anywhere between $500.00 and $700.00. Well, thats crazy. I therefore e-mailed Maytag numerous times and was thanked for my complaint. But they offered no help with this matter. If they dont back their stuff at all, why would I want to buy their stuff? They could have at least offered to help with it. There are only 2 people living in this house and there is no excuse why that washer should start failing already. If I thought it was worth it, I would load it up and drop it off at a Maytag store and leave it there. It still runs. But it makes an awful noise and we are just waiting for it to crap out. I am going to try to sell it for as much as I can get out of it, hopefully before it completely stops. Maybe some fix-it guy would want it. Well tell him whats wrong and they can fix it and sell it to some other poor person. I lost my job in January. Therefore, I cant afford that much to fix it. So, I will now have to try to find something used, because Maytag does not back their stuff. I would rate this machine lower if I could, but that wasnt an option.

Maytag is a product that I would buy any time. Even uses it well last for a long time. If you want to spend money this is a good investment for your kitchen and as for your laundry get the washer and dryer. You do get your moneys worth with Maytag.

Three years ago, we purchased a gas Maytag double oven, it worked fine for three years, then it blew the breaker. When we turned the power back on, we could not turn the oven off. The control panel had to be replaced, dinner too. We had bought the extended warranty, so that was covered. Last week, after four months, it happened again. We placed an oven thermometer inside the oven and it is was higher than the maximum temperature of 600 which the thermometer could measure. We are currently awaiting a new control panel. Maytag used to be a good name, but recommend you to buy something else.

Dryer needed to be serviced within 2 months. Drum seal fell out. Service was no questions asked. Fixed promptly. Washer works fabulous. Gets clothes clean. Surprisingly quiet. You do need to keep up to the sensors on the dryer. Must be wiped with rubbing alcohol to keep performance.

Bought a Maytag Model #MDB8949SAMO dishwasher. After LESS THAN 2 years the motherboard stopped working. Called Maytag to complain, but was told they couldnt do anything. I would give the dishwasher less than a star but the rating system wont allow it.

We have had this refrigerator, model MFI2665XEM7, less than two years. The ice maker stopped working and we had it replaced at least 6 times in a two month period. We had a solid ice sheet in the bottom of the freezer drawer and it leaks water on the floor constantly! Even today... after another ice maker replacement, we have no ice! I never wanted a Maytag, but finances and the small space we had gave us little choice. I am not sure what our next move is. I will NEVER buy a Maytag product again! I should have google this sooner and we could have saved the poor repairman all of those trips!

I should have returned this machine after my first load of wash; it ruined a couple articles of clothing. Later it ripped a throw rug and just recently ruined a drapery panel. Is there any way I can exchange this machine and rid myself of it? SN: C22534900 Model: MVWC400XW4

Dishwasher could do better with washing the dishes better and less recycling time. Also, it would be better if it had a self cleaning unit on it.

Was so excited to get this machine so that I could wash larger loads, including blankets, but unfortunately the machine didnt really clean as expected. That was very frustrating, but even more upsetting was when it began to sound like a jet engine when in the spin cycle. In researching this online, we have discovered that it is probably the bearings. When we called for service from the local store where we purchased the washer and dryer, we were told that it will likely cost at least $600 to repair. We have looked online to see if it is something that we can do ourselves, but really dont want to attempt this as it will require some heavy lifting and a lot of time. I am amazed that a machine like this would fail in such a short period of time and would like to add my name to the list of people who will not buy Maytag again! If a class action suit is ever filed against Maytag for this poor excuse for a washer, count me in, but unfortunately I will probably need to buy a new one before much longer.

This review is for a Maytag dishwasher. I do not know the Make/Model. It did a very poor job of washing the dishes. It may have been the city water, but no matter what I put into the machine to keep the dishes from being cloudy it never worked. It became disabled about a year after we moved in, and it was only about 6 years old. However, there were two families before me that used it and I have no idea how they used it. It was the first and last Maytag dishwasher I will ever use.

I bought this washer brand new in 2011 for $650. I had bought a Maytag washer before in 1967 and it was still running in 1995 when I gave it away. Considering my first Maytag lasted me nearly 30 years (Last I heard the machine was still running in 2005), I never thought my new Maytag would give me any problems, until it was at least 10 years old. (I did know Maytag had been bought by Whirlpool but didnt expect any difference in quality). Boy, was I wrong! After using it for a month the machine broke down and it had to have the clutch and gear box replaced. Last week July 2016 the machine broke down again. It was the internal computer (referred to as the electric control unit) a printed circuit board that retails for approximately $300 (A ridiculous price given that much more complicated laptop and tablet computers today can be brought for $100, the circuit board should retail for no more than $40).With labor the repair bill came to $550, which was nearly as much as a new machine and did not justify the cost. Supposedly the electric control is susceptible to current surges and power outages. Given that this is the case, it makes no sense whatsoever that a machine billed as eco-friendly would carry a part that will doom it to the junk pile because of a power surge or outage and does not carry a surge protector. After learning of my experience Maytag called me the next day and offered to sell me a new Maytag at a discount price, which of course I flat-out refused.I would never ever again own a Maytag appliance or one made by its new owner (as of 2005) Whirlpool. With such susceptible electric units these appliances will sooner or later result in electric fires that will end the life of its owners. The US govt needs to protect US citizens from these predatory companies that make over-prized, throwaway products labeled as eco-friendly that are potentially dangerous. My advice for anyone that is thinking of buying a Whirlpool or Maytag washer dont do it. For those that already own these machines do not run them without a heavy duty surge protectors. It is not worth your life.

We purchased this terrible machine 2 years ago. The clothes come out worse than when they went in! White powdery stuff all over darks! I always have to wipe all dark pants down with a wet cloth! Absolute junk! Really bad product! Never buying from this company again!

I purchased a Top Loading Maytag January 2019 (High Efficiency Washer) and I have had problems with it every time I do laundry. It doesnt matter what cycle I have it on. It doesnt fill properly when I put it on deep full. It tangles my clothes so I have to untwist them when I take them out. It has torn some of my things due to twisting. Some areas of the clothes dont even get wet. Some areas also do not get rinsed properly and I have to repeat the cycle. I have had repair people come out and they cant find anything wrong. I am so unhappy with the washing machine and Maytag just ignores the issues I am having. Im going to have to give it away and get some other brand. I am just devastated that I spent all of this money and clothes are getting ruined.

Bravos MCT maytag commercial technology washer - Bought this washer a year ago. Will not complete cycles. Will not agitate. Never buy Maytag.

The refrigerator had to have repairs in first year. Maytag was aware of freezer issues and reluctantly finally replaced the parts. I had to argue with repairman because he tried to tell me that the freezer was too full.

I purchased a Maytag Bravos XL washer and dryer at Best Buy (Pacific Sales) in March 2013 at Best Buy. I also purchased extended warranty on both machines. A few months into owning the machines, the washer started giving us a UL error light. It wouldnt finish the wash cycle and had to be restarted multiple times before it would do so. I called Best Buy and they sent out a repairman. He said the set-up cycle had not be run correctly by their own installation team (which I paid for), and he said that he had fixed it.A few months later the problem started reoccurring again. Best Buy sent out repairman again who claimed there was nothing wrong with the machine. He left and the problem started reoccurring soon thereafter. I called again, and Best Buy said they couldnt do anything about it because Maytag could only work on the machine (it was now getting an F:51 error message as well). Maytag sent someone out who watched it run for 15 minutes and diagnosed that it was fine and left. I told him that the error didnt occur until the end of the cycle, but this seemed to make no difference to him (he didnt want to wait).Same thing happened again (might run five to ten loads without an error and then it pops up again), and I called Best Buy again. They sent out the Maytag repairman again (different repairman). He spent about the same amount of time as the previous Maytag repairman. His conclusion was that the machine was fine; he told us that this particular washer (the top-of-the-line for Maytag) gets out of balance frequently and that we would simply need to live with it. Like his colleague, though I told him that the error message doesnt occur until the end of the cycle, he didnt stay that long.Not long after he left, the problem started occurring again. I called Best Buy and indicated that theyve had plenty of chances to repair the machine and that I wanted a new one. They said someone would call. The response: another call to schedule a repair visit. I called them back and told them that I didnt want another repairman but rather a new machine (weve wasted hours and hours of our time giving them a chance to make the purchase right). They then had someone from the Geek Squad call, who swore that hed put his best guy on it and that he would actually work on it this time (ordered parts). He was supposed to show up this past Friday but called in sick (now rescheduled for this coming Friday). In the meantime, the machine (last night) quit working altogether. I have a pile of wet laundry and am faced with going to the laundry mat today.Im at an utter loss of words for this experience. It is truly the most frustrating consumer experience that Ive ever had. Ive watched Best Buy, Pacific Sales, and Maytag play pingpong back and forth across the table for months. I paid good money for top-of-the-line washer but have gotten bottom-of-the-line service. Surely, at this juncture, Maytag and Best Buy will finally do the right thing. I am going down to the Best Buy store this morning to visit with the store manager (and then to the laundry mat...not exactly how I wanted to spend my Sunday). If not, then next steps will be to figure out how to find representation to force the issue of the lemon law. Exasperated.

The best we can tell, we got our Maytag in 1991. This was because the repairman told us that was the last year they made parts for it. It ran wonderfully until 2018. The water valve broke, but a repairman easily fixed it. In 2019, it stopped running. The repairman fixed it, temporarily, he said. He refused to charge us for his work because he said we might get a few more loads done before it completely pooped out. Were still using it. I love this machine. It has gone WAY past the expected life span of a washing machine. Weve had it for 29 years!

Bought my Maytag washer and dryer as a set in Feb 2011...like many, I did not get the extended warranty, as I thought this was a great brand. Ive had nothing but problems with both. The dryer takes two rounds to dry, the lint filter is wet and rusted. The belt has popped off and needed to be put back on..The washer does not clean very well. Ive replaced the shift actuator because it was not spinning, now it sounds like a turbo jet taking off. And as of a week ago, my washer started leaking underneath. Paid a tech to come look at it and said my motor was done and Im better off buying a new washer and even recommended that I do Not buy Maytag! So I googled Maytag Bravos and seen all the poor reviews and realized I wasnt the only one! My set is 3 years old and its ridiculous that Ive had these issues, as so many has. Extremely disappointed of this brand and I too, will not be buying Maytag ever again!!

I bought a Maytag Top Loader March 2021, this washer machine is the worst ever. It doesnt clean your clothes, & your clothes stink horribly. BBB and an Attorney needs to compensate for our all buyers.

I purchased a Maytag Dishwasher in March 2013 and the control panel failed in July 2014. I, along with hundreds or thousands of others it seems, discovered that this is an extremely common issue with several models of Maytag dishwashers. Rather than standing behind their products and making it right for their customers, Maytag is hiding behind their one year warranty and refusing to do anything about it or even admit they installed thousands of FAULTY control panels. This has been an expensive, infuriating issue to deal with and I have never been so dissatisfied with a company. Bottom line, they made a bad product that should have been recalled. It blows my mind that they are getting away with this. I wish I had known the recent changes in Maytag/Whirlpool and I wish I had done my research prior to the purchase.

Bought the Maytag high efficiency washing machine with the auto-sensing and deep water wash feature. It took some getting use to because of all the washing choices and different noises it makes. Auto-sensing seems to use very little water which is strange but clothes seem to come out clean. Best bet for me is like the old school way and use deep water wash and light load which is shorter and thats most efficient power wise but will use more water which is fine by me. Also bought the matching dryer and thats a 5 star review. Excellent product.

I purchased a Maytag Centennial - HE Energy Star Washer from the local Home Depot on Guam.... Probably the worst clothes washer I ever purchased. I typically buy a Whirlpool brand for many of my appliances of which I have always been satisfied with the products. I understand that Whirlpool is now the new principal owners of Maytag. I bought the Maytag for my new second home which I have moved into as my primary residence. Great ads on TV that promote the Maytag product line but the product fails miserably in performance. From the day I purchased the washer, my wife, kids, and I visibly noticed the laundry doesnt get as clean as my previous washers, it takes longer to wash a load of laundry no matter what is the preferred setting, the irritating hum is deafening in my laundry room, now the washer has malfunctioned and doesnt cycle through properly, leaving the clothes either unwashed or wet... I do not know who is your servicing agent or center on Guam and I am debating to repair it or just dispose of it. I can tell you now... MAYTAG... NEVER AGAIN. Now I know why the Maytag Repairman is so lonely.... I wouldnt bother to repair it. I hope these issues do not filter down to your Whirlpool products. That Samsung is looking pretty attractive right now. I bought one of their dishwashers that is doing a pretty good job right now.... Guess what? There was a Maytag next to it that I didnt even look at.

I purchased a Quiet Series 300 E71195 dishwasher in 2011. Its about 3.5 yrs old. I guess misery loves company because like so many other complaints on this site my control board died, and Maytag, while saying they care about customer satisfaction, basically said tough luck pal, youre on your own. Sadly I own 3 other newish Maytag appliances. When will these appliances die without support from Maytag? Im not holding my breath. My next step is to complain to the dept of Consumer Affairs and create a page about nefarious Maytag on social media. Avoid the Maytag brand when shopping for appliances. I know I will.

Purchased refrigerator with freezer on bottom. Purchased because made in America and husband raised in IA. Have had water leakage on floor every other day. Disconnected ice maker thinking that would help. NOT. Poor workmanship. You were good, WHAT happened?

Fifteen months after purchase, the lid lock and motherboard goes off. It was replaced with new parts and the machine still doesnt work. Cost of repair is equal to the cost of the machine. With or without an extended warranty, the expense is not worth the investment. While shopping to replace the machine, the dealer finished my sentences on Maytag washers.

I bought a Maytag Centennial Top Loading washer 2-1/2 years ago. Its worked very well, but has started to roar so loud on high-speed spin that you have to leave that side of the house to be heard. The factory technician determined that it had a bad gearbox and that it wasnt anything I had done that caused it. He told me it was going to cost more for parts & labor than the machine was worth. I called Maytag and was told they wouldnt help me because it was after the one-year warranty. When I asked for a supervisor, he offered to pay for the parts, but not the service. Thats kind of like Chevy offering to pay for the defective engine part, but not the installation. I have never bought a major appliance (or even a hair dryer) where I thought 3 years was a reasonable life expectancy. Lifelong Maytag Customer has left the building.

Dishwasher Model #MDB7609AWW2 - I have replaced the touchpad once a year for 4 years. Went online and learned a DIY repair using a Permatex Rear Window Defogger Repair Kit to fill in the touchpad broken circuits. I have repaired it once a year for 2 years. My suggestion is to avoid purchasing this product. Apparently even after multiple consumers have contacted Maytag regarding this widespread defect, Maytag has not issued a recall or assisted anyone. They say if the part can be replaced there is no issue. When the dishwasher works, it is great, however it WILL NOT last. Touchpad will fail and you will be out $124 for the part plus labor unless you do the repair yourself.

It is actually an older model Maytag set that I bought used 4.5 yrs ago. I am very impressed how its held up and how fresh our clothes are still. I have always loved Maytag and will buy again if needed.

Purchased a Maytag Dryer, Washer and Oven Range in December 2011. Both washer and oven were serviced within 1 year under warranty. The dryer stopped working in August 2013, not under warranty. Total cost to repair is $450. Called Maytag to see if they could reduce the repair cost, answer... NO. Maytag spends millions of dollars in advertising... Built Strong to Last Long but they cant spend several hundreds to keep customers. Will never buy a Maytag, Whirlpool, KitchenAid or any other related company product ever. Their motto should be Built Weak to Last Weeks.

I was always impressed with the front loading spin washers commonly found in laundromats. The top loading Maytag Bravos does a great job of cleaning clothes and does not stick another door in your way when loading or unloading it.

I bought two sets of Maytag washer and dryer. We have had them for less than a year and the tubs had to be replaced out of both of them. Now, its less than six months later and they are doing the same thing, so the tubs have to be replaced again. What kind of equipment are you making? This is just an outrage. You are scamming people to buy your products by your so called advertising and rep. Well, this is false advertising on your part. I will never buy another Maytag anything or Whirlpool either. I also see there are a lot of others having the same thing being done to them. I would be ashamed to even have these products to sell. Shame on you. Scammer.

I bought a Maytag Refrigerator (Model No. MFT2672AEM10; Serial No. K31503192) on 05/13/2013 at LOWES. On 07/27/2013 my son got hospitalized due to some kind of infection. He had fever and diarrhea that didnt go away. We didnt know what caused it. When my wife was cleaning the refrigerator, she noticed that the ice bin container had a rusty screw and metal plate. Why is the ice bin screw/metal plate rusting? We informed Maytag about this issue and they replaced the ice bin. Now, the replacement ice bin is rusty again. I sent an e-mail to the Maytag Customer Service Manager on 04/20/2015 and was told that its no longer covered by the warranty. I informed the manager that this is a defective/flawed design/rusting part from the beginning and Maytag should have REDESIGNED it when I informed them first hand and not just replaced it with the same defective/flawed/rusting part. I told the manager that this is a safety concern and Maytag needs to do something about it. The Customer Service Manager I talked to didnt want to do anything about it.

Maytag Dryer model # MEDC400BW. I purchased this dryer in March 2015 the fuse went out in August. It is now November and it is out again! I have been buying Maytag since I left home at 18. I am 62 now, so I have been a loyal customer because Maytag was a great product. Not anymore since Whirlpool bought them out! You have to call them to schedule a technician and then it can take anywhere from 1 week to 3 depending on when they get the parts because they have to order them, and nobody else can come out to work on it if it is still under warranty! This is so lame and just not right.

I purchased a Maytag Neptune 24” front load washer (MAH2400a) and 24” electric dryer (MDE2400AYW) on October 26, 2005 from Sears in Chesterfield, MO. In April 2011, the drum in the washer began to slush and grind. Water also began pooling around the machine. I called Sears and arranged for service repairman. Before he even looked inside the washer, the repairman wanted to give me a coupon for $50.00 off a new washing machine from Sears. After my insistence, he finally opened the washer and told me I needed a new drum. Because of the Sears repairman’s reluctance to look at the machine, I had another appliance repairman review it and was told that the water pumps for this model were defective. Any loose items the size of coins collected inside the pump and damaged it. I paid $340.00 to get the pump replaced. Ten months later, the dryer started smoking. After scheduling a service call, I was told the heating element burnt out and it would cost $360.00 to replace. It was then I noticed that the washer was leaking again. I took the front base cover off and saw mold growing under the machine. A little research uncovered that this set of machines has had many dangerous problems, from mold to catching on fire. There was a class action lawsuit filed and won by consumers in April 2005, yet I was sold this model in October 2005. I feel both Maytag and Sears knowingly sold me a defective and dangerous product. I would like to be refunded for this set.

I bought my washer in 2016 and now it’s broke again. This is the fourth time! I’ve gone everything to take care of this and it’s a lemon! I will never buy Maytag again. I want to buy USA products but four times for repairs in three years is way too many. I guess it doesn’t matter what name is on it. My last washer was a GE and was still running after 15 yrs when I bought this one. Not one repair ever made on it! I’m telling everyone to stay away from maytag.

Maytag Bravos top load washing machine - This is the worst washing machine I have ever used. Like some of the other complaints it leaves lint on your clothing. It does not put enough water in the machine. The so called smart technology that senses your load does a terrible job. Your clothing is halfway out of the water, with dry spots, even after 10 minutes of agitation. I am constantly adding 3 to 5 gallons of water to my loads to get things in the water. And if I want to let thing soak for a while you have to unplug the machine, because after 10 minutes it will automatically drain the water out. 2 years of dissatisfaction. I cant wait for it to die. I should have come to this site first. Never buy a machine without an agitator!

After owning my refrigerator for about six months, it started to reek, the smell permeating all of the food in the fridge. After cleaning and disinfecting the fridge and throwing out all of the food I found that the smell was just as bad as before. When I checked online I found that Maytag owners have been complaining about the smell for over a decade now. It is caused by a poorly installed drain pan. The fridges design directs air flow so that the smell enters the fridge and distributes it evenly throughout the fridge.

Had it for over ten years, had no problems. We dont use the oven too often but it is simple to operate and has served us well. Easy to clean, stainless steel like looks on the front goes well with our other appliances. Reasonably priced too.

After a year, the plastic parts of Maytag dishwasher is breaking and upstairs propeller is no longer running. Do not buy this product. I made that mistake.

My refrigerator was delivered on April 3, 2016. I began calling for service July 2 when the bottom freezer door started depositing ice chunks on my kitchen floor every time we opened it. An appointment for service was made for July 18, service never showed up. Another appointment for August 3 was made and again service never came. I called the 800 number on Aug 19 again arranged service for Aug 24 after hours so that we did not have to take anymore time off work. When repair finally looked at the fridge they said the door was not aligned and did not close so the frost builds up and breaks off onto the floor. This can be fixed with a new door that can take from 6 weeks to 8 months as they are not stocked and have to be made at a factory. The fridge constantly runs and is starting to leak water through to my kitchen floor and basement ceiling tiles.I called Maytag/Whirlpool on Aug 25 and the service agent told me the best they could do for me was extend my original warrant by 6 months while I wait for replacement part and they advised I purchase the extended warranty. The second agent named Gabby I spoke to advised me to call Home Depot where I purchased the fridge to see if they would do something for me. She would write down my concerns but had nothing more to say or do for me since the repair person deemed the unit repairable and a part has been ordered. I called Home Depot on Aug 25 and I spoke to Appliance Dept who told me the manager who could help me was off that day. He advised me to stick weather stripping around the door to seal the leaks. I said I was hesitant to do anything that may void a warranty and he agreed. He suggested I may get a loaner fridge but I have heard nothing yet. I want a replacement fridge.When you pay $2000 for a fridge it should be worry free for at least a year? I have been reading reviews and I am wondering why this is not a recalled appliance as this seems to be a very common problem. I am sad that Whirlpool is not standing behind this product. Home Depot has been in touch with me regarding this fridge issue and the lack of customer service provided by Maytag. They are replacing the fridge on Sept 9th 2016 and taking the old unit away. Home Depot has tried to get in touch with Maytag and they have not gotten a response at all about my faulty unit.The staff at Home Depot in Peterborough have been excellent to speak to and have apologized for the issues with getting service to my appliance. I am very grateful to them for their assistance and for following up with me in this matter. The downside is that I am getting another exact Maytag unit as a replacement so hopefully this does not start all over again. Home Depot has been a great retailer to deal with. I am very saddened to hear that even Home Depot cannot get responses from this manufacturer. I have also lodged a complaint with the Better Business Bureau.

I bought this range (Gemini Double gas range) in 2010 but was not installed in my house until 2011 due to time delays in kitchen re-model. I paid $1310.00. It was serviced 3 times once under warranty. About a year ago the igniter went in one of the ovens for the second time and one of the stove burners wouldnt light. Since the other oven and 3 other burners worked we didnt call for repair, then a second burner stopped working and we called our Maytag dealer. 2 different service techs came one with more experience and both said the same thing the stove wasnt worth fixing due to cost of parts. One of the problems was the screws in the burners couldnt be removed due to rust and deterioration of the screws. They would break and cost other components also to be needed. So after 7 years of use and already having repairs done I have to buy a new stove. It will not be a Maytag. I also bought a top of the line Maytag dishwasher and one month past the 5 year warranty the electronic panel burned out. After calling Maytag and complaining they did agree to pay for the part close to $300 but I still paid for labor. When I looked at reviews for the oven before purchasing they werent too good but wanted a double oven at the time and always had good luck with Maytag in the past. I thought buying a higher priced model would be better quality. Not so. After calling Maytag today the best they could offer was to buy an extended warranty for $380, I declined. My advice - Listen to the reviews. The Maytag repairman isnt sitting around idly anymore!

I bought this washer from Home Depot and was told I could load large comforters and even sleeping bags in it because there was no center agitator. There NEVER seems to be enough water to wash and rinse clothes completely. The water saver feature cannot be used as I have to use extra rinse cycle EVERY load to rinse soap out of clothes or I get white residue spots. I have MANY MANY shirts that have small tears in them I believe caused by this washer. I have monitored shirts I put in the washer and again today lost another high quality fabric T shirt. I have saved all of the shirts in hopes that one day there will be a definitive report that this washer design stresses clothes and damages them. I am going to purchase a new washer and it will not be a model like this.

Bought a nice looking Maytag fridge 2 years ago. For the past 6 months it has been leaking all over the kitchen floor. Most recently it has started leaking every 2 days. It is so frustrating as well as extremely dangerous! Both my younger kids have slipped and fell because of the slippery floor. We now have to keep a towel there all the time.Please let me know if there is a product recall. Not the Maytag we used to have. My parents bought all their Maytag appliances when they got married and they lasted over 30 years! This is why I bought the Maytag fridge... not sure of the quality now.

I own my oven for 10 years. It still looks brand new. The bottom oven went out and they do not sell the replacement parts anymore. I think its terrible that I had to go and buy a new oven when mine still looks brand new.

Purchased my Maytag Dishwasher MDB7749SBM on 5/13. 3 weeks ago the panel went out! I found others have had the same complaint on their Maytag Dishwashers too! I also learned this model was discontinued from Home Depot. Is this because Maytag knows this Dishwasher was JUNK and that they allowed consumers to buy this model knowing it had these problems - I believe so! I find it absolutely crazy that Maytag has not issued a RECALL and now I am out almost $700 plus if I get it fixed or buy a new one, I am out even more $$! There has to be some RESPONSIBILITY taken from Maytag!!! This Company was built on an excellent reputation but now this company reputation is considered POOR for selling defective products and doing nothing about it!

My home has all Maytag appliances, all just over 2.5 years and I have had no issues with any of the other equipment excepting the fridge. The fridge itself works very well when it does, but some things are just wrong/flawed with the French door fridge.1. The Evaporator mechanism is flawed and keeps accumulating frost over the Thermistor sensor, which in turn shuts off the fan and the fridge itself stops cooling rendering all the produce bad within hours of purchase. The freezer and icemaker works fine during this time. The first time a tech came in during Warranty period and put come Aluminum foil over the thermostat and zip tied it and told us that the issue is resolved. Fast forward 18 months or so, same issue. This time they want to replace all parts since the last time it did not fix it. How convenient isnt it? So now I have to shell 500 plus bucks to solve what was not fixed the last time. Flawed design is all it is; do not purchase any of the French door fridge from Maytag/Whirlpool or be prepared to buy an extended warranty and a down fridge every 12-15 months at the minimum. In my case shell out 500 bucks every 15 months I guess.2. Sloppy icemaker: Ever heard of an icemaker that thinks and drops 4-5 cubes when requested and thinks again before giving another 4-5 cubes? We see it all the time at Soda fountains. This is what to expect off a Maytag ice maker. And lord knows if you have guests, they will run through the batch of ice by the very first meal and then the princess ice maker needs 12 hours to make another batch of ice.3. Noisy fridge: Ever heard a noisy fridge in a very quiet home? This Fridge excels at that. Just about the time it shuts off the compressor, boom it goes on again.

I love it. Laundry as well as horse blankets. It does it all! I have never ever had one problem with it. Love the delay start setting as well as the extra rinse cycle.Easy to clean the gasket and keep the soap dispenser out to air between washes!

I have had this dishwasher for 3 1/2 years. Replaced the touchpad 2 years ago and now the touchpad is dead. I read all the other comments that are similar to mine and am thinking to replace this junk dishwasher. I will not be buying from Home Depot as they are selling cheap products that are defective!

I purchase my Maytag Side by Side Refrigerator back in 2006 New. I purchase a Maytag based on the supposedly quality of their Products. And I have stove, and dishwasher as well. A week ago, after purchasing groceries, and made it home. The Refrigerator had gone out. I tried calling Maytag without success and broke down and called sears repair to come out. Well they made it today, and I was informed the Compressor had gone out, and would cost me $998.00 to repair. Of course I told him to get out of my home, because at that price I could purchase a new one. And you can bet it want be a Maytag ever again. I am so disappointed in their claims of being the best. Hype!!!

I bought a Maytag MGR5605WW range on July 3, 2011 and it took till mid August before I received it. Right away I noticed when I put a pan on the grates, I had to be careful so they did not slip off. Dangerous! Then I made a pizza, and when I pulled the rack out of the oven, the rack tipped down and the pizza slid down on the oven. Danger again! I went over to Menards and they gave me the number of A&E (1-800-771-3029). I called them when I got home and an A&E person said they would call me back. After a few more calls, no one ever called me back. I went back to Menards. They said I need to deal with Maytag. I am very concerned with the racks, and so is everyone else. They are cheaply made. Tonight I had a family member place the frozen turkey on the rack and it bowed down! Danger again. The grates have a few chips. This is a nightmare. What a piece of trash. I’m trying to get someone to respond. This stove is dangerous to my well-being, and I have no other choice but to use it.

We purchased a Maytag Dishwasher (model number mdb6759aws3) about 3 years ago. After about 1 year, the control panel started to go. Certain options would not light up. If I used the options that did light and shut the door, the dishwasher would work. I had called Maytag, and they were charging almost $200.00 to come out to repair. Now after 3 years, the entire panel is out. We had someone come out. We ordered a new touch pad for $265, and it still did not work. It is the control panel that is dead. What bothers me is that after reading online, this seems to be a continual problem, and Maytag does nothing to help the consumer.

Maytag Neptune was purchased over 15 years ago to replace GE, which we purchased when children were little. I wanted a step up in quality. I remember paying around $499 for this unit. This is an analog unit. The intellidry feature has been a real asset, protecting our clothes from over drying. We have had this machine for nearly 20 years. It has been real reliable, sometimes drying 20 loads a week. Large capacity, but has to fit down a narrow and twisting stairway. Must be energy efficient, have good reviews and decent price. We always look for sales or buying incentives. Brand is secondary to quality. Knowledge of an appliances historical reputation is important. I would look at reviews, especially concerning cost of repair. I would attempt to get a hands-on view, before purchase from a reputable supplier at the best price. My dryer has only required one major repair in the time Ive had it. A few years ago we replaced the motor and blower, and I have personally replaced the drum support rollers twice. I hesitate to replace this machine, because the analog controls have proved very reliable.

I am sorry I purchased this machine. It was meant to replace a 17-year-old Maytag dishwasher that was not repairable. I figured they were good machines. Wrong. Perhaps I have a lemon, I do not know. I bought the machine on the 23rd of November and it was installed on the 29th of November. Here it is December 12th and I am sick to my stomach. I have already had to contact Maytag customer support and have a repairman coming. This machine does not clean worth a damn! My glasses look worse coming out of the machine than when they went in. I have run two loads with the machine so far. The auto-sense cycle is a joke. It took over four hours to complete and things did not come out clean. Last night I tried the normal cycle. It came up with a run time of 2:36. The first rinse was cold water. The detergent cup was open and empty at 20 minutes in. So what does the machine do for the next two hours??? When the cycle was finished I looked at the glasses and they were spotted and streaked with remnants of fingerprints and lips. So I ran it again trying the quick cycle. Not one bit of difference, still nasty looking glasses. If this machine cannot get the upper rack clean, how can I be sure the lower rack is getting sufficient cleaning? One would think that for $600 it could at least do the job it was meant to do.

Maytag Dishwasher MDB7749SBW03 - We purchased this dishwasher in 2013. About 1.5 years after purchase the control panel started to get flaky and different settings wouldnt work. Not long after that it stopped working at all. I did some troubleshooting and found that the ribbon cable that connects the control panel to the control board was corroded due to water/steam getting to it. Since we were past the one year warranty I bought a new control panel and things worked fine for about a year, now the panel is going bad again. I contacted Maytag and they said they cant do anything to help me. This machine is not even 3 years old and going on its second control panel. I would recommend staying away from all Maytag products.

I owned my double oven Maytag Gemini for 14 months and I was absolutely satisfied with it. I was running a cleaning mode on the bottom oven and the lock froze. I have tried everything with it to unfreeze it, including the suggestions offered on the internet. I havent been able to do it on my own and I cannot afford to hire a repairman. I called the help line offered by Maytag (after waiting for 32 minutes), the representative actually laughed at me when he found out it was past the 12-month warranty. Though this laugh may be unusual, I feel it is very indicative of the way Maytag handles any problems; Maytag doesnt stand behind their items, they are now built shoddily and they could really care less about retaining their customer base.

I bought Tapan gas stove last year, but all your ranges have a problem. Whenever we clean the range, it never goes straight stay up ,even when I bought from Lowes Store and I told them they said that defect from manufacturer. You have to correct your manufacturers defect, I want an answer as soon as possible. Thank you.

I purchased the top model Maytag dishwasher, and within four uses, I noticed major water damage to the side of my cabinetry. I pulled out the dishwasher and realized it was coming from the side unit where water enters the tub. These things happen, and I phoned their customer service department expecting this unit to simply be replaced, being that it was less than a week old, and that I would have been left a satisfied customer. They were willing to send a technician over to try to fix the problem, but not replace it. I now have to replace my cabinets, and maybe even my granite as it may be damaged in the removal process. I am not asking them to fix that even though the damage was caused by their dishwasher, but a new dishwasher, I did expect them to cover. Their customer service stinks, and I suggest to anyone that if you have any problems with a new unit, the best thing to do is return it to where you bought it. Im sure they will gladly give you a new unit and send the bad one back to Maytag. Dealing with Maytags customer service is the worst thing you can do. They do everything in their power to not replace it. Instead, theyd rather lose a customer for life. Whats sad for them is that Im a builder, and I usually build approximately three houses per year. Thats a lot of units theyve lost sales on over a simple replacement of a dishwasher. Its not a good way to do business. The bottom line is, stay away from Maytag.

I bought the newest most energy efficient Maytag model M9BXXGMYM00 (for about 1K) from a local appliance store and after 9 months it wouldnt freeze. The local store picked up and left a loner for the fridge and made repairs in shop returning it in a week - great - except that approx. 11 months later the fridge again wouldnt freeze. The store sent repairman who charged 125$ to tell me it had leaked its freon again and would need repairs which were no longer covered under 1 year Maytag warranty. I asked the store to back their work but was only given a refill of the freon and half off the service visit. 2 months later the fridge is not freezing. I know because the repairman and store owner Mike told me that it had freon leak and that Mike himself had made repairs to the leak that the unit wasnt repaired.I have read that freon is toxic and can be hazardous to people with heart conditions and a list of bad effects. Maytag will only send someone to repair unit for a service call charge plus the repair charges and will not replace a defective unit. I can take the appliance store to small claims court over faulty warranty repairs but probably not the health risks - which are disputed by the experts. Ive read reviews and have heard from people who have appliance issues that the companies basically use a defective unit as a cash cow sending repairmen back again and again and never fixing the problem making a lot of money off of frustrated people who have bought a lemon from a company who doesnt back their product or their work. I was only looking for a decent refrigerator and paid plenty for one. I now have to get rid of a nuisance or pay to fix it - probably more than once and spend lots of time getting through the court vs. store owner process for any of the 1000 bucks lost on the defective toxic junk I got from Maytag.

I love the functionality of this Maytag refrigerator. The inside is so nice and big, I can almost fit anything into it. When I need to make a lot of food for a lot of people, this refrigerator really foots the bill.

Maytag washer Model #: MVWX655DW - I purchased this machine at Lowes in May of 2016. Always was a loud machine but seemed to work ok. In April 2018 the machine stopped working correctly. The spin cycle would lock up and not finish leaving clothes soaked. Called Lowes and waited for their repairman. He came and said it was the clutch and drive motor. Repair is over $400. Machine is worthless. Huge mistake. Never buy a Maytag. I called Maytag to see if they would warranty it. They basically said, Sorry only a one-year warranty on it. I told them the reason I bought it was it had 10-year warranty on it. They said only certain parts but its the drive motor that is clearly marked on the machine that has the 10-year warranty. I was told, No sorry. What huge waste of money. I am out close to $600 and Lowes only give you a store credit with their protection plan.The credit is not enough to purchase another machine without more out of pocket expenses. I will never buy another Maytag and I would not recommend anyone else does. Their warranty is a huge joke. Their customer service is terrible. Maytag should not even bother sticking the 10-year drive motor warranty on their machines. They do not honor it. My advice do not even consider buying one. You will be out the money and be purchasing a new machine within two years.

Bravos XL washer- This is probably the worst purchase I have ever made, first off, at $1000 it was a pricey purchase however, I chalked it up to it will last many years without issue. After only 3 years, the unit leaked water and was so loud you couldnt stay indoors while it was on spin cycle. The bearings and seal were completely shot and needed replacement, after the sticker shock of having a good repairman fix the problem I decided to tackle the job myself. (Thank you YouTube). All was well for the next 2 years until it all happened again. Maytag is junk and will never get another dollar from me-ever! A Speed Queen TR5 now sits where that piece of crap used to reside. BUYER BEWARE!

I bought the larger capacity machines to save time because Im so busy with my family and wanted to cut down on loads. I was surprised to find the capacity can really only operate at half, which is as large as my old, smaller machines. The washer is extremely sensitive, meaning it may take four or five tries (this morning was four) to arrange the clothes - even a small load of delicates - in it in the exact way the machine wants before it will allow the cycle to start. This is exceptionally frustrating, particularly during the busy morning or when you are tired at night. So you have to stand there and wait until the sensing function is happy and you see the water pouring in. Yet often you will return to the machine and it will have an error message that occurs inexplicably during the spin cycle, so the wash cycle will need to be restarted. It cannot just be continued. The machine is not only a huge time waster but a water/detergent waster as well.I learned that the sensing function on the dryer is useless as well after coming back to many loads of damp clothes that sat there, got little funny smelling as a result, and had to be rewashed in the nightmare washer lol. So now I just use the timer function. It takes about two hours to dry a regular load of towels, so be prepared for that. I bought Maytag because it is an American-made product, but I wont make the same mistake next time. If the quality is any reflection of the functionality, it probably wont last very long anyway. Heres to hoping.

My dishwasher is less than 2 years old. Dishwasher will go on when we are not in the house. Cant control the panel. The control panel lights all come, have to cancel to stop the machine. This could be a fire hazard.

I purchased a very expensive set of Maytag washer & dryer (topload washer) and heavy duty larger capacity. Firstly- I purchased this through Home Depot on Labor Day weekend and did not receive this set until December 2020. This set has all the electronics and Im going to tell you NOT to purchase either one. The dryer MUST have a metal solid vent. This sets your dryer out into the walkway of a laundry room. If you use a heavy flexible metal vent; your sensor will be going off constantly telling you your vent is plugged and to clean it. I had a dryer vent company out twice to clean and inspect the wall & roof vents yielding nothing. I also have a dryer vent cleaner which I hook up to my vacuum and I clean the dryer vent monthly. If you lose power. You will need to unplug your dryer and let it reset to be able to use it.The washer is also terrible for the outrageous price. Again; glass heavy duty top load with all the electronics. You cant get the washer to fill even on deep fill. Also; do NOT put a lot of clothes or jeans or blankets in this machine. It will not be able to level and spin. When you try to use the drain and spin cycle; the sensor keeps going off. I swift the contents around and around and finally end up having to take soaking wet cloths out into the garage until I have one sheet in the machine and it will spin out. In addition- the CLEAN with Afresh mess. This forces you to clean your machine- whether you are in the middle of trying to get clothes drained or not.Buy something thats a simple workhorse with one button. Stay away from any bells and whistles because its only going to cause you heartache in the long run. I wish I would have read reviews prior to spending $1,700 on a Maytag Washer Dryer set (ON SALE- for God sakes). This is the biggest piece of garbage I have ever purchased. Buyer beware.

Oven does not have consistent temp, cant change temp without preheating ruining whatever is cooking. 5 visits from Maytag during added warranty and never any satisfaction. Tough Microwave minutes and the oven goes off. Told it was a Govt requirement. Very noisy even after its off. Maytag wouldnt help or Home Depot either who warranty was through.

Brand New 2019 Model 465 Washer and like others are saying is a piece of junk as they do not fill the drum with enough water even on the Deep Water fill option. The laundry does not circulate and nothing gets clean. Maytag is really poorly designed and manufactured these days and a complete Rip Off!

Three-year-old top load Bravos. Started doing the LD/SD tango about one year ago. Intermittent fault, but becoming more prevalent. Can spend an entire day attempting to finish one load; sometimes must be unplugged overnight to clear faults. Washer receives heavy use from extended family of five adults and two children but has never been overloaded. Machine is horribly flimsy and constructed of the cheapest possible materials. I wish I had removed the back prior to purchase.Just because it is possible to attach a processor to a piece of equipment doesnt mean its necessarily a great idea. Any geek can tell you that the three things most despised by a digital device are heat, humidity, and vibration. A washing machine by definition is an epicenter, a breeding ground, for those specific environmental factors. Well done, Maytag. You have demolished what was, perhaps, the most respected name in the business. Good luck getting that particular rep back. Purchasing a Speed Queen. The living embodiment of old-school. Electro-mechanical timer. Stainless. Porcelain-enamel. American-made. Not one complained on this site. Might just shoot an Office Space vid centered on the demise of the Bravos. This time, its personal.

I purchased this washer... the Maytag Bravos. It is the worst clothes washing experience. I only use one cycle as the other cycles do not provide enough water to wet the clothes. It is a large capacity top loader. DONT DO IT!

We (husband and wife only - no kids) had our Maytag washer for 4.5 years and around year 3, the control panel would need to be reset by unplugging it and plugging it back in. That alone was an inconvenience. This time, the Control Loc light is lit and will not go out despite using all troubleshooting suggestions listed in the guide so the washer is not usable. 10 year warranty covers the drum. I say that is like getting a warranty on tires and when one goes flat, you are told it only covers the hubcap. I can only rate the unit as garbage. Model is 5500, front load. So much for Made in the USA.

Bought this Maytag Bravos Washer online from Lowe’s in the holiday season of December 2017 because my previous Maytag HE washer broke after 17 years. I have had nothing but issues with this washer right from the start. The clothes do not come clean as I find myself putting them through the wash cycle two or three times to have them washed and come somewhat clean. The clothes come out soaking wet that I have to put them through the rinse and spin cycle at least one or two more times. I called Lowe’s to complain about this washer and they said they only have a 30 day return policy and they would be happy to call for service for me. I told them it didn’t work from the start but they didn’t care. So now, sadly, I have a repairman coming this week to fix my new washer, And hopefully he can fix it that I can use it and it can properly wash clothes. I wish I would have her read the reviews on Consumer Affairs about this washer before purchasing this Maytag. Not happy with Maytag. I would have never bought it and bought a different brand. Codes appear on the face of the washer better. Nowhere in the manual that I had to personally download myself because it didn’t come with one. And oh did I mention that I need a step ladder to reach into the bottom of the tub? This washer should come yellow because it is definitely a lemon!