2 Year old washer. First the actuator was replaced. A 150.00 charge. Two months later the pump is shot. Another 200,00 to replace the pump. This is worst piece of ** washer I have owned. I would not recommend to anyone. Stay away. I would give it 0 stars if I could.

In April 2010, I replaced my washing machine (still functioning after 12 yrs) to upgrade to what I believed to be the top of the line Maytag Bravo 5.2 HE washing machine. Module # MVWB850WL0 type: 580-02. This machine of 3.5 yrs leaks underneath and after having the service tech come to look he advised me it will cost over $800 to fix (I paid over $900 for this unit). He says its the bearings and went on to ask me if Id been using the HE laundry soap (as if Im an idiot) and went on to ask whether Id been washing bedding. SERIOUSLY?!? !... After much research on this issue, I discover that there are similar complaints all over North America. Very disappointed and I want this lemon replaced by Maytag.

I purchased Maytag microwave model MMV4205AAQ in 2005. I use it infrequently. It stopped heating in Nov. 2011. It must be replaced. But after this experience and reading other comments, I will not purchase any Maytag appliances in the future.

Model MWVC360AW0 has never done a decent job cleaning. Washing pods would not dissolve completely. Ruined a lot of clothes. Had to rewash many times. This is a piece of junk. Extended warrant folks at Home Depot no good either.

Bought Maytag Bravos in 2010. It does not clean but worse than that it rips clothing (for example: loops off pants, holes in pjs, tons of ripped towels), so many items of clothing torn that I cant keep count. Today I had a pillow case ripped apart (see image). I have had four sheets ripped that I can no longer use. Maytag should have recalled this washing machine. I have the Maytag Bravos dryer also and the drum was on backwards on it when I bought it.

I bought a Maytag washer and dryer in Cookeville TN. In 2018. After a year it quit. The service man from the authorized dealer in Cookeville could not repair it. After numerous calls Maytag sent a service man to repair it, this took about three weeks. This washer is a Maytag industrial, it has a 5 year parts and labor warranty, and 10 years on the motors. Now it is out again, after calling Maytag, and holding on the line for an hour, finally I had to chat with someone, and they set up an appointment for about 3 days. So service company call now and says it will be another week before they can sent someone to look at it, and another week to get the parts. They also questioned my warranty. I gave high dollar for this washer, what’s happened to Maytag?

You would be better off going to the river and washing your clothes with rocks. Piece of junk. Maytag will have you believe that the six inches of water this washer uses to clean a comforter is enough. I would like to know which individuals in the dept of energy thought this water saving feature was a novel idea. What use is a giant washer tub if it doesn’t have enough water. Sorry Maytag, my clothes used to come out clean with your old model, now I spend hours trying to figure out ways to get this washer to clean. Currently I am using the clean washer cycle for my comforters and then using the deep water cycle. So it takes about four hours to do a load of clothes. Thanks Maytag! This Maytag Bravos XL washer stinks.

I purchased a washer/dryer, Maytag from Home Depot Nashville. It was delivered and set up. 02/24/17 the date of purchase, delivered 03/07/17. I have tried in every way to get the washer to wash properly, but to no avail. The water level doesnt cover the clothes, it takes 10 to 15 minutes for the wash to begin its cycle. It doesnt spin the clothes dry enough to put into the dryer. The washer makes all kinds of sounds thats drives you nuts while setting up to not wash your clothes clean. I have contacted Maytag on several occasion about this problem, they sent out someone to service the washer. Now, why would a brand new washer need servicing. Somethings wrong. It isnt functioning up to standards and they should give me another washer.Now on 05/18/17 the washer was serviced, I have called them again to do something about this piece of **. I was told that the only thing they could do is come service it again. Why, must this brand new washer be serviced every week. It doesnt make sense... I dont want this machine, I want my money back so I can purchase a machine that will wash my clothes properly. I purchased a secondhand washer and dryer from a used appliance store, it lasted my family 10 complete year. The only reason I dont have it now is because I wanted to upgrade, since I have never had a brand new set. What a disappointment. Everything that looks good from Maytag isnt good. I dont understand why they wont stand behind their product.Somethings got to be done about this. Maytag will not take my money 1,200 and force me to keep this malfunctioning piece of nothing. Im going to Youtube this product so the consumer can see how this product doesnt work properly, therefore they wont waste their hard earned money. I will be contacting the BBB Nashville, and wherever I need to. I will let the consumer know the make and model of this product and where it was purchased from. Maytag I want every penny back. And, should hold you responsible for ever time I have had to go to the wash house because my brand new set wont work, and your company wants to service it every time I try to wash. I purchased this appliance on the strength of the well known name, that was the wrong thing to do.

My five year old refrigerator freezer was leaking due to a corner filler part left in the the freezer compartment that lodged over the drain hole in the freezer. It cost me $232.90 to have a repair technician dig it out. MAYTAG accepts no responsibility for poor inspection, workmanship or quality control and they will not reimburse my fee.

We lost our home in a tornado in 2005 and had to buy all new appliances. So, I bought a Maytag Neptune front load washer and dryer. It was my 1st ever. I will never buy another Maytag appliance again. Just at the end of the 5th year going into the 6th year, the bearings started to go. So, I checked with the place where we bought it and was told how expensive it would be to fix. It was anywhere between $500.00 and $700.00. Well, thats crazy. I therefore e-mailed Maytag numerous times and was thanked for my complaint. But they offered no help with this matter. If they dont back their stuff at all, why would I want to buy their stuff? They could have at least offered to help with it. There are only 2 people living in this house and there is no excuse why that washer should start failing already. If I thought it was worth it, I would load it up and drop it off at a Maytag store and leave it there. It still runs. But it makes an awful noise and we are just waiting for it to crap out. I am going to try to sell it for as much as I can get out of it, hopefully before it completely stops. Maybe some fix-it guy would want it. Well tell him whats wrong and they can fix it and sell it to some other poor person. I lost my job in January. Therefore, I cant afford that much to fix it. So, I will now have to try to find something used, because Maytag does not back their stuff. I would rate this machine lower if I could, but that wasnt an option.

I bought a Maytag washer 3 years ago. Maytag gave me a number for one of their warranty service repair shops in my area. The first repair service doesnt even respond to my calls. The second repair service is a total ripoff. So in summary, Im stuck with a 3 year old washer that has a broken drive assembly that the warranty wont cover.

The cost was right for the quality of the product. Brand was also a factor. We have had no problems either machine, both work as expected and have fully met our expectations. We recommend these products. Energy efficiency, ease of use and capacity were all considerations in making the selection we made. Maytag continues to hold a good reputation. Regular repairs, low quality construction and a cheap finish which looks tacky and is also difficult to clean would each be deal breakers. We purchased our full-sized, side by side Maytag Neptune Washer and Dryer gently used from a private party who needed to obtain different models due to a remodel of their laundry/utility room. We paid about $600 for the pair.

This so called high efficiency washing machine, and others like it are absolutely awful. They do not properly clean clothes. I frequently have to put loads of clothes through two or even three times in order to get things cleaned properly which our old washer did easily in one wash. That is the exact opposite of efficient. It is so bad that it actually borders on being a genuine scam. Do not buy! Huge waste of money.

Please do not buy a Maytag washer top loader. It does not get enough water and it does not clean your clothes. It is the noisiest cheapest made machine out there. If you have kids you really need to bypass this one. I have had this for 10 months and its only me. Please especially if you have children stay away from it. Im the most unhappiest camper Maytag ever had.

I purchased the subject Maytag washer (MHWE201YW-3.5 CU FT WHT FRNT LD WSHR) from Home Depot in December of 2012. I got exactly 1 year of use and then the washer stopped working. I called the Home Depot repair person who came and repaired the unit. The repair lasted two weeks and the washer stopped working again. Because the unit was no longer under its 1-yr warranty the Home Depot repair person was not available for repair. Another independent Maytag repair person came and evaluated to problem. He said the computer which is located on the motor was no good and to the tune of over $400.00 (parts and labor) a new motor was purchased and installed. It lasted two months and it quit working again. After several months I was finally able to contact the original Home Depot repair person for one visit. He said he would check the code message and get back to me. I never heard from him again. I have been taking my laundry to the laundromat ever since and it is getting expensive. I dont want to spend another $400 on this machine as it will only break again. What do you recommend?

So for the past year our 1 yr old freezer has been leaking and holding a sheet of ice at the bottom. Ive been wondering why my electric bill has skyrocketed the past two months and we just realized that the freezer wont even stay closed anymore. Maytag has become a VERY POOR product. Our less than two year old $450 Maytag Drier just busted as well. After paying repairman after repairman and replacing different parts, we had to get rid of it. I am very dissatisfied with Maytag and will never purchase a product with their name attached. Please keep us posted if there is a class action lawsuit. This is unfair to make a product that fails immediately for the price that is paid!

This is the absolutely worse washer I have ever owned! My clothes actually come out dirtier after they are washed. It leaves white stains on clothes that I have to scrub out by hand. Maytag you should be ashamed of yourselves for coming out with a washer like this. It takes me 2 or 3 times to wash clothes and I have to use the power wash, extra rinse, and maximum clean setting to even come close to cleaning. It is cheaper to take my clothes to the dry cleaner now than use the washer. I called Maytag numerous times, and they said that they will charge for a service call unless there is actually a mechanical issues. They will not honor repairing the machine if it does not wash clean. I will definitely NOT recommend this washer.

MFI2568AES - Last night we woke up because of a noise coming due to continuous snapping of the waterline against the walls of the refrigerator as well as a wall of the house structure itself. Very loud noise. I pulled the refrigerator, went behind it, and shut off the waterline. That stopped the noise and allowed me to go back to sleep. However, need your help to resolve this issue. I will appreciate if you can offer me pointers and guidance.

My husband and I bought a Bravo XL washer in the fall of 2015. I certainly wish we had read the reviews on this site of this product. We would have saved ourselves a lot of money and grief. This machine does not clean clothes and actually damages them during the spin cycle as reported by others. This low water no agitator technology does not work on a top loader. Stuff doesnt come clean! Im not sure what we are going to do but we learned a valuable lesson the hard way. We purchased this machine in September of 2015 and are unhappy with it!

Our Maytag Bravos Top loader with no agitator is headed to the junk pile after 1.5 years of BAD service. I honestly believe that whoever writes a good review on this machine is NOT an actual owner. Lets start with how it NEVER cleaned our clothes... The washer uses barely enough water to get the clothes wet. Soap remains in the clothes so the family is constantly itchy! If you add 3 additional rinse cycles, its still not nearly enough to get out the detergent and youre left asking yourself, What about the HIGH EFFICIENCY???? Next theres the issue of the water never being hot ENOUGH to kill bacteria (were back to the itchy thing). Its suppose to be an energy saver, but at what expense? Its not QUIET like promised (well maybe for the first few months). But upon opening the lid, you realize it was quiet because not a lot was happening to get the clothes clean. Now lets talk about the horrible smell... I dont know where its coming from... It occurs during the wash cycle and smells almost like a natural gas type odor. This is NOT because the washer wasnt cleaned once per month! Maybe its the bright orange RUST near the bleach dispenser or all along the inside rim of the lid... Remember its ONLY 1 and 1/2 years old. Before I get to the ISSUE that finally did this machine in... I have to mention the machines UNEVEN load response.. Brace yourself, it sounds like 1000 tribal drums... and if you dont readjust the 200 lb water logged load, it will just keep on filling up with water and draining indefinitely (so dont leave the house if youre washing jeans, blankets or sheets!). The FINALE of our machine is what I kind of always suspected it would be... the lid lock!!!! One day it stopped in the middle of a cycle and the door remained locked... After unplugging and retrying, the door unlocked, the buttons all worked, but the machine will not fill up with water or start a cycle. To be honest... I am so GRATEFUL! I get to buy a new machine and although Im pretty pissed that the machine died after just 1.5 years, we can finally have CLEAN clothes again, peaceful laundry days and get rid of the ITCHIES!!!! Bye bye FOREVER Maytag!!!!!!

We purchased a Maytag dishwasher MBD7749AWM on 03/15/12 from Home Depot. The control panel went out on 01/24/12 under warranty. The unit was down approximately 2 weeks waiting for parts and a second service call. Just six months later (approximately 08/05/12), the control panel failed again. Thinking that a trusted American, iconic industry leader such as Maytag would stand behind their product, I called for what I thought would be a covered repair. I explained to a supervisor that their panels have not made it 1 year in service. She assured me there were no out of the ordinary problems with the panels for my model dishwasher in one breath, then stated they were out of parts and on backorder for three weeks. Now the truth comes out, further telling me that the unit is out of warranty and nothing can be done short of sending out a repairman, that I would be responsible for parts and service. After further discussion, she reluctantly agreed to send me the part for free if I arrange the installation and told me that it was very simple to install. When the part finally showed up on my doorstep with no paperwork, it was wrong. When I called and complained for waiting 3 weeks for the wrong part because there was no quality control in their parts and shipping department, all they could do was say sorry. They told me just to keep the part they sent and they would send the correct part. I begged that they ship the correct part overnight and they adamantly stated that was not an option. Maytag stipulates their process only allows ground shipping from FedEx per their contract. Knowing I had no other option, I agreed and waited for 5-day ground. The part showed up 13 days later and delivered by USPS. Apparently, I was lied to again and the left hand has no idea what the right hand is doing. Apparently, Maytag/Whirlpool have an inadequate and poorly trained quality control system in place and their manufacturing and electronic divisions are surly lacking a strong management team needed to go in and clean house. Instead, the whole mess they have contributed to continues to haunt Maytag has continued to be made to believe its okay to produce subpar products while continuing the complete demises of a once trusted American, iconic industry leader all while living on the Lorals of twenty years past.Whirlpool would do itself and this country a huge service by just letting this brand die and thrown on the heaps of scrap steel headed for China where maybe they can copy and fix what they were not capable of.

I purchased this machine less than 1 month ago. Have had tech here twice - he cant find anything wrong with machine. As for large capacity it will hold a lot of clothing, but will not clean them. I have had to put less than a 1/4 of tub full of clothing (about 15 small items). Use high water level, extra rinse, then rinse and spin again to get the 2 tablespoons of HE soap off my clothing. Takes over 2.5 hours to wash about 15 items. I have called Maytag and they will not back their product. I purchased at Home Depot and they said they have to do what Maytag says. Sending another tech out in 2 more weeks. Takes more water, more electricity, and more time to wash clothes than ever before.

I purchased a Neptune front-load washer in November 2005. Now that its out of warranty, theres nothing that Whirlpool can do for me. The front panel of the washer that surrounds the door has been rattling for a few weeks, so my husband took it off and found a crack on the top right section of the panel where its bolted to the frame. There is a rust bubble where the crack started. We couldnt see any of this until he took it apart. The cost of a new front panel is $185 and the response from Whirlpool? They are “very sorry” that this has happened, but there is nothing that they can do. Oh, really? Well, I come from a long line of Maytag owners and there is something I can do: spread the word about the disgusting piece of junk I paid $1,100 for! This washer wasnt even made here - it was made in Korea and its not worth $100! Note to Whirlpool: your customer service sucks!

Maytag washer, model# mvwp575gw0, which is under warranty. This washer is less than one year old. Within the first couple months the transmission leaked oil and service tech had to replace the transmission. A few months later – another problem, clothes wet after spin cycle - tech told me the agitator base and/or couple parts need replaced. Quality control appears to have been lacking at the factory when this washer was made. This house has only one person presently. The washer was not abused.

I am sorry I purchased this machine. It was meant to replace a 17-year-old Maytag dishwasher that was not repairable. I figured they were good machines. Wrong. Perhaps I have a lemon, I do not know. I bought the machine on the 23rd of November and it was installed on the 29th of November. Here it is December 12th and I am sick to my stomach. I have already had to contact Maytag customer support and have a repairman coming. This machine does not clean worth a damn! My glasses look worse coming out of the machine than when they went in. I have run two loads with the machine so far. The auto-sense cycle is a joke. It took over four hours to complete and things did not come out clean. Last night I tried the normal cycle. It came up with a run time of 2:36. The first rinse was cold water. The detergent cup was open and empty at 20 minutes in. So what does the machine do for the next two hours??? When the cycle was finished I looked at the glasses and they were spotted and streaked with remnants of fingerprints and lips. So I ran it again trying the quick cycle. Not one bit of difference, still nasty looking glasses. If this machine cannot get the upper rack clean, how can I be sure the lower rack is getting sufficient cleaning? One would think that for $600 it could at least do the job it was meant to do.

So far, so very good. This is the first time owning/using an electric oven. I just love my Maytag. It was affordable, especially since it was a combo sale with the over-head matching microwave from Home Depot. Two years later and it's as if I just purchased it. Wonderful, wonderful, wonderful.

Spent a lot of money on a Samsung washer. Will never buy that brand again. Too much money for only working for 2 years. And left clothes dirty. Had to wash clothes twice. My Maytag washer was bought with a deep water wash cycle. Totally love it. Also not a front loader.

I bought Maytag Bravo washer and dryer set in Nov 2012. Washer door lock broke shortly after 1 yr and now the gearbox has broken. DO NOT BUY MAYTAG BRAVO WASHER. The cost to fix is more than the value. Before the gearbox death the sound it made while spinning was so loud you could not hear the TV or have a conversation in the west end of the house. Visitors were stunned at the noise it made. I called Maytag warranty and explained I am having the same issues as everyone else, what are you going to do? The answer was nothing. Please read the other reviews, same issues. It never cleaned clothes anyway, bad design, bad company and bad corporate values. Model number MVWX700XLE.

I purchased this high-end dishwasher 7 years ago and 3 years of fairly light use, the control panel on the top would operate sporadically or not at all. Called the dealer who sent out the repairman that installed it and had to replace the control panel to the tune of $300 once the labor was included (took 2 visits as he had to order the part, so 2 trip charges). Now 3 & 1/2 years later, it is doing it again!! A call to Maytag and then a transfer to Whirlpool customer service got me nowhere. They said there were no recalls or documentation for problems with the dishwasher. Really??? I see lots of complaints on this problem with very similar Maytag dishwasher models. They would not send me a new part at no charge as a result but offered to set up a service appointment for me so I can spend another $300 (probably higher now after 3 years) and would register my complaint. Thanks for nothing!Doing that would turn my originally $900 dishwasher into a $1500 one with the result that it will probably fail again in 3 years. Absolutely ridiculous customer service. I saw a YouTube video on taking it apart and applying silicone around the ribbon connections as others have done in the hopes I can get it working again for a while as I dont have the $$$ needed to replace it again on a retired fixed income. :(

Both my washer and dryer are Maytag. Dryer element shorted out but was still under warranty so was fixed. Washer is very loud and now makes a rattling sound. Every so often it will hang in the middle of a cycle and the lid wont open until I unplug it.

We purchased a Maytag refrigerator Model # M1TXEMMWS02 and Serial # E01103420 in April of 2010 from Home Depot in Aurora, Illinois. First off, we did register the fridge online via Maytag which of course, they have no record of! Now, we go on vacation and come back to all of our food ruined because the refrigerator stopped working! No refrigerator should stop working within two years! I called Maytag and they offered me a Repair Plus One package of $302.73! Are you kidding? We paid $400.00 for fridge. Then of course, only one-year warranty and have to pay at least $75 for a service call, labor plus parts! If it’s the compressor, the charge is $326.20, plus shipping and handling! What a joke! There needs to be longer warranty and should offer free service calls and much more. I am disgusted in Maytag products and in which we purchased due to a reputable name! Never again.

After reading all the reviews I realize this is a wide spread complaint. After 2 1/2 years the control panel on my Maytag Dishwasher will not work. You press the keys and hope for the best. I am thinking of going to the media with my complaint. Maybe we will all get some sort of refund or upgrade.

The washer worked great for the first 6 months, then it didnt dissolve the soap, it wouldnt complete the cycle, and there is a loose bolt like sound when you spin the drum. The load level is not an issue. We have had the serviceman out four times, he has called the tech support each time and they cannot resolve the issue. Maytag said sorry! Unless it does it constantly then they cant help. The control panel has been replaced and the drum has been replaced. So we keep paying the water and sewer bill to rerun the load 1/2/3 times to get it to complete the cycle. This washer was purchased last May, 2011 and they say were stuck with it.

So wife and I purchased a Maytag dishwasher in late 2012. A year and a month later it turns into Hal 9000 from 2001 Space Odyssey. I press normal, it shows light rinse. I press heated dry, it tries turning off the life support and blowing me out the air lock. Finally, in March it dies. No power, no nothing. $500+ for an appliance that lasts 2 years. So for the past few months, while we wavered over buying a new brand or spending $250+ on a repair, we were washing dishes by hand. It was as bad as my grandma used to say it was. Then, by chance I ran across a web blog talking about this being a common problem, and there are hundreds of complaints, and its a problem with a $4.00 part on the control panel that can be fixed with a Q-tip, rubbing alcohol, and silicone... Im not a handyman by any stretch of the imagination, but even this I could do. Unplug or switch off the breaker. After unscrewing all the screws, (not your standard or Phillips head either) unplug the control panel from the control box and remove the control panel. On the back, youll notice a flat cable (pictured below) that will have dark marks on the opposite side of the part sticker. Gently clean this with a Q-tip and rubbing alcohol. I then covered the back (side without sticker) with silicone, (you can get at hardware store or Target) let dry, and put everything back together again and now its working better than new. Im regarded as a master handyman in my house, and I didnt even have to hear the dishwasher sing Daisy Bell as I disconnected it. With such a simple fix, Im amazed Maytag didnt just own up to it and get it addressed. The millions it will end up costing them in the long run, by this frustrating experience shared by us all will have them thinking twice in the future (hopefully). It is a shame they seem to be adopting the business model of American auto manufacturers of the late 80s. Ill update this in a year and a month to let you know how the fix worked, and you owe me a beer for saving you $150 - $600 for a repair or replacement. One word... VICTORIOUS!!

I have two major issues with my stove. First is that you have to press enter after setting an oven temperature and it doesn’t even beep to remind you before just cutting off. Older, forgetful people like me have probably prepared countless dishes for the oven only to find that it is not preheated. The second is that if you turn on the timer, it cuts off the oven. You only make that mistake once before writing the timer off as useless. I have a hard time believing that they ran either of these by anyone who cooks! One other mixed feature, the heating element for the oven is below the floor of the oven. This causes it to preheat slower - which compounds problem #1 - but makes cleaning a breeze.

My Bravo washer will not wash a set of sheets without dancing across the floor. So irritating to have to run in and separate the sheets that have ended up in a ball. The dryer is ok. Except my old Maytag had a loud buzzer that went off when the cycle was done. My new dryer has a dainty little chime that cant be heard if the washer is going. Wish I had my old set back!

Bought a MDB7601AWW, and then replaced front panel to stainless. Configuration options are great (can’t find better at cost up to $1,200.00)! I haven’t had an issue with any stains on non-stainless tub. Problem is now control panel failing for second time. After 1st time, sealed all connections in silicone to prevent steam from affecting it, as recommended on DIY video. I just replaced the door latch, thinking that may solve it, but hard to troubleshoot without any indicator lights. This second failure (2 yrs later) shows no indication that steam or water caused it. It does start now, stuck on heavy wash, heated dry, sanitize - per top lights. Front lights totally out. Debating whether to buy a new dishwasher ($$$) and give up super config (hard to find fold-down tines and fold-down small shelves on upper and lower racks, clips for small items, and basket that can be changed, placed anywhere) or spend at least $162 for the panel AGAIN and hope I get another 2 years from that while trusting that some other element doesn’t go out. I believe Maytag should, at minimum, make the panel reasonably priced by offering a rebate, since the part is not sold directly through them. Obviously this problem is a design flaw. I am the only one in the house, so the dishwasher is not under heavy use. At least I found how to replace it myself on YouTube, though it requires the door to be completely taken apart and would be easier with an extra set of hands and a younger back. Hard decision since it seems newer, expensive appliances have problems as well. If I buy new, I will not hesitate to get an extended warranty (1st time ever).

Why is no one doing anything about the crappy product that Maytag is putting out. I am a single mom of 4 and I had to purchase a new refrigerator about 3 years ago. Spent a lot of money on this Maytag, approx. $1400 and it is now useless. I had nothing but issues with it from the time I got it. The bottom freezer kept icing up and then leaking all over my kitchen floor. I had to call a repair guy out, who charged arm and a leg and said it was fixed and 3 months later it was doing the same thing. Since I could not afford to pay ridiculous amount of money to repair it again (although I question what they said they fixed), I had to chop up the ice each month and take huge pieces outside and i had to keep towels always at the bottom of my fridge (yes very attractive) but it ruined my floor and carpet. Now all of a sudden the piece of junk just shut off and stopped working and keeps making this popping noise. Lights went out in front panel. So I had to call a service guy out again but this time I called an independent local guy that is not gonna rape you in charges like Maytag does and he told me to look into this that he has heard so many complaints that the front board with control button has been known to blow out the back circuit board, which is what happened. He told me that parts are MDs, so he would have to get another manufacturer and he heard that even with replacing both of them, it has been known to not work and Maytag takes NO responsibility at all for any of this. THIS IS WRONG. I cant afford to spend around $800 to now fix this or another $1,400 to buy a new one. So I am without a refrigerator. What a nightmare. MAYTAG, TAKE RESPONSIBILITY FOR YOUR CRAPPY PRODUCT. We are hard working people that spend our money and expect a good product. I also have an oven I bought and I can tell you it is a piece of crap too. I swear at it all of the time, as it takes forever to cook anything and the outside that is supposed to be stainless steel is all yoked up. It is like a tin can, looks horrible. I will never ever buy another Maytag product and I hope that ConsumerAffairs steps in and does something about this.

On 8/26/16, we purchased a top-of-the-line Maytag dishwasher from Lowes of Palm Bay, Fl. It began leaking water out one side shortly after installation. Because of a hospitalization, we were not able to report the problem to Lowes until the first part of December. A repairman from Brandts in Sebastian, Fl. came out on 12/6/16 and said it might be the door gasket, but he did not have a new one with him and if it continued, to call back. I called again and another repairman from Brandts came out on 1/3/17. He said it was out of square and he took out 2 screws and said to cut back on detergent because too many suds could cause it to leak (which we find ludicrous). Now it leaks on both sides. This is not a small leak; it soaks the bath towel we put under the door. On 1/11/17 Brandts sent 2 repairmen out and they claimed we needed to cut way back on detergent and put in a capful of salad oil because our water softener is causing the suds which causes the leak. We now use 1/2 teaspoon of detergent and the capful of salad oil. It is still leaking. Our previous Kitchen Aid dishwasher never leaked and we used the recommended amount of detergent in it. We are apparently stuck with a brand-new dishwasher that cannot be fixed. We will NEVER buy another Maytag appliance.

Maytag Centennial 3.4 top-loader was purchased at Home Depot. It has never worked yet. On 4/28/12, the third weekend, I sat home for the servicemen to fix this junk machine. The first two times, the machine didn’t work ten minutes after they left and today they went to the wrong address. I have much more important things to do than to sit around and wait for someone to figure out what is wrong with this machine. It would have been cheaper for me to junk this brand new machine and buy a washer from a company that makes washers that work!

Maytag wall oven Model# MEW7530AB01 - We ordered this oven from Home Depot on Aug. 28/13. It was delivered on Sept.7/13. After a self clean cycle, the oven failed on Sept. 24/13. It was repaired on Oct. 23/13. Parts come from U.S. Im in Canada. Part # W10545255. It hadnt cleaned completely so I used the self clean mode again on Oct. 24/13. Oven failed. Fixed again on Nov. 15/13. Same part. Tested self clean again. Oven failed. Repairman fixed a different part. Thermostat #4449751. Oven still not working, had to order the front fuse again. Part # W10545255. Fixed Nov.19/13. Failed again Nov. 19/13. After not having a working oven for so long, Maytag finally agreed to send a new one. It arrived Dec.5/13. Tried cleaning cycle just to make sure. Oven failed. Same part. Called Maytag, told them I just wanted my money back. They refused. They would only repair. I agreed to have a repairman from another company come out. I told Maytag what part it was. They sent the repairman out on Dec. 19/13 with the wrong part. I called Home Depot a second time. I had called them after I talked to Maytag. This time Home Depot said they would take back the oven once it was repaired and I could have a store credit towards another brand. The repairman fixed the oven on Jan.9/14. Home Depot picked up the oven and replaced it with a GE and I love it.The part failing is a fuse in the top of the oven right at the front. Both repairman noted that a lot of heat is in this area during a self clean. When two ovens are having the same problem, I come to the conclusion that it is a design flaw and should be recalled. I only talked to one person at Maytag who was polite on the phone. That was the woman that got me the new oven. Everyone else was rude and hostile. I was even asked why I would clean a new oven. My experience was not a pleasant one at all. I wont be buying any products made buy the Whirlpool Corp. again.

I positively HATE the new BravosXL Maytag washer, which has no decent agitator. It is ruining my clothes, as it spins with little water and leaves soap residue all over the clothes. Additionally it puts large, long wrinkles in my knits, especially disfiguring slacks. Maytag must have known how rough and ruinous this washer was on knits BEFORE selling it to an unsuspecting public! I want my money back in order to purchase an old-style, well-functioning agitator washing machine.A class-action suit should be brought against Maytag. There was no way to know before buying and using that this machine is horrible!!!

I purchased a washer & dryer from Lowes on December 3rd. On February 20th, my washer stopped filling up. I called customer service and had someone come out a few days later. The repairman said the sensor broke & it would take 10 days for part to come in. After 2 weeks, I tried calling repair company and they would not answer phone for Maytag, or me. Maytag called another service provider, and it will be another week before part comes in. Never could get in touch with anyone who was helpful! Now it’s been a month, and still not fixed!

Worst experience of my life!!!! Don’t buy a Maytag washer!!! It’s agitating our clothes dry. Putting holes in clothes. We bought a warranty that’s pretty much useless. They will not replace. Only fix parts.

This is a wonderful washing machine. For cleaning clothes it does exactly what you expect from a washer. We have had 2 Neptune front loaders. They, however, have a couple flaws I dont want to live with again and will be looking for one that has come up with the solution to them. One, the bearings on them need replaced on a periodic basis or it sounds like a 747 taking off. Two - the front gasket around the barrel has a mold problem no matter how much you try to keep the thing clean. Other than that, these machines perform fantastic.

Maytag Quiet Series 200 only 1.2 years old: I moved into my home about 2 months ago and the touch panel on the dishwasher, which is of course just past the warranty expiration date, has progressively gotten worse until now, doesnt work at all. I have tried calling Maytag many times on numerous occasions, who apparently only has one phone line because its ALWAYS busy. The cost for the touch panel on this dishwasher (model# MDBH945AWS3) is $150 which isnt even worth fixing since I can go to Lowes and buy a new FRIGIDAIRE for $300. The problem is the circuitry from the touch panel to the control board gets too much moisture in it with no protection around it. If I were them, I would find a way to make all these parts separate so regular people, like you and I, would be able to buy parts a lot more cheaply and repair these items ourselves. However, since the front panel and the circuitry attached to it is all one cohesive unit that cant be taken apart from one another, nearly at all without ruining it, then I might have been posting a different review here. However, that is not the case. IF I could actually get in touch with Maytag, I would ask why on earth isnt this a recalled item and when they are shipping me a new part since it seems everyone is having the same issue with their Maytag dishwasher, no matter what series it is. I do not plan on buying a Maytag appliance in the future. I do plan on buying a Frigidaire since the rest of my appliances (stove, fridge and overhead microwave) work perfectly without any issues whatsoever.

Bought the set at Home Depot. The gear box went out after 2 1/2 months of use. I called the manufacturer warranty site and spent close to an hour on the phone then was given an appointment to have a service repair person look at it. Two days before the scheduled service call they called and said they would have to move the appointment out by a week. After diagnosing the problem, oil all over the floor and stained clothes from the oil, was told it could be up to 2 weeks until the part arrived and installed. So my warranty is being used up while the machine is out of service for a month. Beware of buying a Maytag!!!

Unreliable! When you push start, it goes into sensing mode and starts to fill. You walk away thinking it will run to find out an hour later it is still in sensing mode! Wasting electricity, your time and talk about stress! You have a 50-50 chance it will go on and run the load, but if you dont have time to stand there and watch it. FORGET THIS WASHER. Also does not clean as the old agitator washer, which I luckily still have, yeah. Always read reviews before buying anything. Nice website.

I would not recommend the Maytag washer with the large tub. It does not clean your clothes. I called Maytag and they do not care as long as it uses as little water as possible! Not a good value for the money!! That was the first time and last time I buy a Maytag... Thats the last $5000 they will get from us!

I have had it since 2011 and still works as good as it did back then. I love it. Hope it helps people decide when they go shopping for a dryer. I have a dog so I have to keep her clean so I wash a lot of her bedding and she sheds a lot. She also sleeps on the with me so that other bedding that I put for her on my bed between her clothes and mine which I do separate. The dryer works a lot and it is still going strong.

I am very dissatisfied with this washer (Maytag Washer Bravos XL), it doesnt use enough water to cover the clothes. No matter which cycle you use, the clothes dont come clean. Who cares about water sensing if your laundry isnt clean. I will not buy another water sensing machine, I think the consumer should make that call on how full to fill the washer. Even on power wash the small agitator turns slowly. Not happy with this machine at all.

Like so many other consumers, I was drawn to the Maytag name because of what I thought was the high quality of their products and their stellar reputation. So when our old wall-mount oven failed, I sought out a replacement from the Maytag line. I purchased a model MEW5530WDDB17 in 2011 and had it professionally installed. It worked well for a couple of years. Then, suddenly, three of the numbers on the digital control panel stopped working, making it impossible to set the oven to any temperature that included a 4, a 2 or a 5. When I contacted Maytag, I was informed that the unit was out of warranty, but that I could schedule a service call. I had already researched this issue online and knew that the service person would inform me that I needed a new control board and that one could be installed for around $300, and that the new board would come with a 90 day warranty. When I asked the person to whom I was speaking, she said that she had no further information for me. I know that a lot of others have had this same issue with their Maytag range/ovens, and many of them agree with me that we will never purchase another Maytag product.

I emailed Maytag https://www.maytag.com/contact-us/ about my model number MBL2258XES3 Fridge on Dec 31. They scheduled a local appliance repair company and they came out today, Jan 5 and did the repair and defrosted the compressor and freezer compartment. 45 Mins is all it took. Thanks Maytag.

We purchased a top of the line, state of the art Maytag washer and dryer Neptune. The fill valve failed twice, flooding the first floor and the big storage room below. Thank God we were here! Now the thing halts mid-cycle and wont continue. The repairmen both said the design is messed up and they hate to work on the Neptunes.

I owned an front loading Maytag Neptune Front Load Washer MAH5500 for more than 10 years and first 5 yrs doing 2-3 loads a day for a family of 12 so this machine held up well, and only issue we had with the machine was the rubber around outside needed to be replaced after about 9 yrs.

I purchased my Maytag Centennial 1 and 6 mos ago and it is already broken. The washer wont wash the clothes, just sit in the water and wont spin. I called Maytag, they offered me a warranty for another year for $371. The washer was only $550.00. When I tried to get set up with a repair service, the only company they used which was going to charge $105 just to look at it, would only take cash. When I called back to discuss with Maytag, they were no help at all. I was told they wouldnt even do the warranty since I scheduled a service even though I canceled it. I will never buy Maytag again.

Topload Maytag Bravos washer sounds like a jet on spin cycle. Called Maytag, no recalls or service issues. Just wanted to sell me a service contract for over 300.00 dollars that would fix it and be covered under warranty for a year on anything that went wrong. Could set me up with a service call, but it was six days from now - no thanks. The washer this replaced was a Sears which was 26 years old. It still worked and I sold it for 75.00 dollars. Guess I will stick with Sears!

6 week old High Efficiency Washer leaves lint and soap lines. Ive tried deep water wash plus the 2 rinse settings and I still have to wash the load twice to get rid of the lint lines and soap lines. Ive also tried every combination of settings to no avail and I follow the guide to a tee because this machine actually weighs the clothes to determine the water level. Maytag customer service was polite but useless. Im assuming its the poor design but customer service says I will be charge for the warranty service call if no problem is found. Maytag, another fine company down the drain. PS, parts are made in China.

I purchased a new Maytag dishwasher (model #MDB4651awb3) for $300, in December of 2009. Seven months later, the dishwasher refused to start. Some lights on the front panel would remain on, while others would not respond. The Maytag repairman made a house call and replaced the front control panel, and vent. After the repair, the dishwasher worked fine for nine months. Then, the same thing happened again. It refused to start with the same front panel light problem. I called Maytag, and since the machine was now past the one year warranty, they wanted $275 for an additional 1 year warranty, to repair the machine. Since I can buy a similar new machine for $25 more, and felt this was now an ongoing problem, (it would be the third panel in less than two years). I expected Maytag to offer more to take care of their lemon problem. Since they refused to reconcile the situation, they obviously no longer stand by their machines. I will no longer buy Maytag/ Whirlpool machines, and do not recommend them.

I have been on the chatline with Maytag customer service for two days, trying to enforce my warranty, which expires next week. My washer flooded my kitchen over the weekend, and I contacted Maytag to schedule the repair under the warranty. First, the woman, Aisha, looked up my registration, and confirmed that I was who I said I was, that my address and phone number had not changed, and told me that according to the records, the washer was purchased on 2/7/2011. Whats the problem? First, they wanted the model and serial numbers. I realized that this is important information in determining what machine needs what repairs, except there was not one sticker anywhere on my washer! Aisha said that the technician would not perform the repair, if the manufacturer did not install the model information properly on the machine. As if I had any control over the placement, or lack thereof, of proper ID for the washer. This was followed by a request for proof of purchase. I explained that I moved, and misplaced it, but I would have it emailed to me from the original purchaser. I was told that unless she could verify the proof of purchase, and the date of purchase, she could not schedule the repair under the warranty. This is despite the fact that not 5 minutes ago, she had just read this information from her computer! I asked her why would I register someone elses washer under my name and address? She didnt care. I told her I would have the receipt emailed the next day, and she stated that regardless of the date I requested, and scheduled the repair, if the actual repair took place after the expiration date of the warranty, it still would not be covered! I told her that makes no sense. I have no control over your scheduling issues. If you cant honor the warranty if the repair is made after the expiration date, then I need a date prior to that. I am entitled to the terms of the warranty, and intend to use them. Aisha said again that, without proper proof of purchase and purchase date, without proper tags on the washer, and if the repair takes after the expiration date, it would not be covered. I disconnected from her, and reconnected with another rep, who told me that some of the information Aisha gave was incorrect. I can schedule the repair, get the receipt and email it, or submit it through the chat, and regardless of when the repair was actually done, the warranty would still be honored. This person couldnt be sure what effect the lack of proper tags would have on that. My third re-entry into the chat was no better. I located a copy of the receipt in my email, and contacted the chat again. An almost amazing thing happened! This woman again confirmed all of the information Aisha recited last night, and was prepared to schedule the repair, without even asking about proof of purchase. This woman, Jennifer, was willing to schedule the repair, verify that it would be covered under the warranty, even if it was after the expiration date, because I had called and arranged the appointment before the expiration date, and she was willing to have the missing manufacture tags replaced. I had to ask her three times to review the email, and confirm that I had the correct receipt for the technician. I asked if the technician in the course of repairing the washer, had to remove the drainage hose, could he either replace it with a longer one, or add an extension, because according to Lowes at the time of installation, the hose they installed was supplied by the manufacturer, not them. Jennifer stated that since he was only there to repair the leak, and installation is not covered under the warranty, I would have to pay for him to replace the wrong hose, with the correct hose myself, even if he removes it! I told her that she needed to ensure that the technician absolutely did not remove the drainage hose from the back of the washer during his repair, because if he removes a part that is obviously the wrong part, and then replaces the wrong part after his repair, I would file a complaint every single place I possibly could. Why would a repair technician remove a part, determine that it is the wrong part, and then put it back! That is like a mechanic repairing the axle of a car, and discovering the brakes are bad, but since he is only there to repair the axle, he replaces the bad brakes after fixing the axle! He was going to be able to replace the missing manufacturer tags, though! This entire process took at least 3 hours and two days. To date, Maytag/Whirlpool is absolutely the worst company I have had to deal with, right after Sears, and ahead of AT&T. The consequences are that so far, Maytag refuses to have the technician replace the wrong hose with the correct hose, if he removes it in the course of repairing my washer.

I loved my first Maytag combo unit and when that quit I bought another Maytag. The Neptune is a front load washer. I immediately noticed the door gasket getting moldy. I contacted Maytag whose response was leave the door open. Well, I did that and not only did I still get mold, but the light burned out. I recently started having trouble - the water doesnt drain and the clothes are still wet. Rather than have it repaired, I elected to buy a new washer/dryer unit. I would NEVER again have a front load washer and certainly not Maytag.

My washer is about one-year-old. Several months ago I noticed a brand new shirt was damaged after laundering. I thought it was inferior material. A couple of months later I saw a similar situation with another garment and started being more careful with the laundry settings using delicate, short, light washes, etc. The problem has happened a THIRD time to another garment. It appears this washer has a hunger for delicate jersey type fabrics. I started reading online and found out at it is indeed the action of the agitator and I need help rectifying the situation.

The refrigerator has been very dependable for over 14 years. The biggest problem we have had is failure of plastic tracks on drawers that break and had to replace drawers and other problems with plastic components like deli drawer coverlet, and door shelf door plastic. Recently we have problems with the touch control panel on front of door. Not working properly for ice dispensing and temp. control although temp is maintaining what we had set prior to failure of control panel.

We bought a Maytag Bravos XL assuming that because of the brand name it would be a great machine. WRONG. This washer is truly awful. Every single load of darks comes out covered in soap scum. I always have to rewash every dark load with no soap for a full normal cycle in order to get the scum off. My whites are probably also scummy but often I just throw them in the dryer as I cant see the scum. Its just a very, very poorly designed machine that obviously wasnt tested before they started manufacturing and selling it. Its criminal how Maytag continued to sell this piece of junk, and Ill never trust their brand again.

Purchased model MBF1958XEB4 September 2012. The unit is provided with a bottom freezer. About 2 month age water was forming and freezing on the bottom of the freezer compartment and leaking on the floor. It appears that this is a common design flaw recognized by Maytag with an updated part available that is intended to correct this problem.Contacting the extended warranty company I was informed that this is normal maintenance and not covered under the plan. Liars!! One does not remove a car engine to change the oil. To correct this problem the refrigerator is required to be pulled from the wall, disconnected from power, remove the back lower cover, disconnect two wire cables, replace the drain tube and reverse the process. Normal maintenance - give me a break. The company promoting this phony plan is Federal Warranty Service Corporation in Atlanta, GA. Do not buy a plan from them and if you have one cancel and receive a refund if possible. Maytag get into another business because your product is junk.

It leaves white stuff all over everything. You have to rewash or rinse black clothes at least twice. We have to clean the washer frequently or the clothes smell like mildew. I chose Maytag because I thought they were the best. Apparently, I was wrong and it was a mistake buying this.

My Maytag Bravos washer is 6 years old. I had to have the motor replaced about 2 years ago. Now, it gets stuck on uL on every spin cycle. I had a technician come, and was told its just cheaper to replace the machine at this point. What happened to the Maytag man of old, the one who never has any work to do because the machines are built so well?!

I bought this range Nov 2019, beautiful range that’s it. Stove top scratches very easily and hard to clean. Oven racks rust, got them replaced on the guaranty they still rust. Oven dirty never gets clean, If I could afford it I would on the curbside. I wouldn’t even give it away. 3 oven in 48 years of marriage, worst oven ever.... Sure would like a full refund, I mean 1500. What a ripoff.

Maytag dishwasher MDB7749SBM2 - I purchased this unit from Home Depot. It worked fine when working. In less than two years the control panel had issues. Would not let you start cycle, would randomly start on its own, would light up randomly, would only let one cycle work, would not work at all, etc. I received no help from Maytag. After open up the door panel the problem is obvious. The ribbon cable from touch (control) panel to control board had black spots from corrosion. Poorly insulated or poor design. $150 for part and another $100+ for repairman. As Ive seen from several of these posts it appears to be a common problem now to Maytag, which they choose to ignore in spite of class action lawsuits. Obviously last Maytag product Ill ever buy.

After speaking to a Kim today... Im more than angry. The control panel on my dishwasher is broken. Had repair come out and they told me a few months past warranty. Kim tells me the only thing still under warranty are the racks?! Im extremely angry at the poor service we are receiving but pleased as we have cancelled the washer and dryer (Maytag). If youre thinking of going Maytag or Whirlpool, cancel! Not worth the headaches or cost.

Purchased a Maytag Bravos washer in 2009. Was told it was water efficient and electric efficient also. Spin cycle twisted my clothes in a knot and left white blotchy doors on my dark clothes, had to rewash my clothes again!!! Then started making a horrendous noise that could be heard from one end of the house to the other, like it was going to explode at any given time. Called technician, paid $75 and said it was bearings and that it would probably did the same noise again even with fixing it, that Id be wasting my money!! Worth getting rid of it!! I just hate it!! I will never buy another Maytag again.

We bought the Maytag washer from Home Depot on 5/4/2011 and it quit working on about 7/2014. We had a repairperson look at it and he said the drive transmission is worn out. He recommended that we buy a different machine since the part does not hold up since the part is made out of a plastic fiber material that does not show up. We bought the Maytag because we thought they had good products but a 3 year life on a wash machine is not acceptable. It is installed at our cabin so we only use it part of the year on limited bases.

I bought a brand new Maytag washer and dryer at Home Depot and did not use until a week later when I found out that the washer did not spin out the water and the machine turned off automatically when cycle was not finished. As a result my load was soaking wet. I called Maytag customer service and they sent the technician. I was standing next to the technician to see what was wrong with the washer. After checking several things and seeing the unresponsive of the washer the technician told me the control unit failed and the clutch also failed. He had to order the parts and it will take at least a week for him to come back and fix it.I called Maytag customer services and complained about the brand new washer and ask them to replace it with a new one as I dont know if the problems returns and it doesnt have just one failing part. Both the controlling unit and the clutch were failed. Also i bought a brand new products I expect it to work. I dont want to pay for brand new washer and I could not use it plus it took so much of my time going back and forth between Home Depot and Maytag. It was so stressful and I had tons of laundry that need to be done. I also had to take half a day off to call the Maytag customer services and Home Depot.During my first call with Maytag customer services I asked them to call my local Home Depot so Home Depot will allow me to exchange for another Maytag washer. They had refused at first but when I told them all the reasons above they agreed to call Home Depot and allow the replacement. They asked to hang on the phone while they were calling Home Depot and finally confirmed with me that I could go there and do the replacement.Surprisingly when I came to Home Depot they said they did not get any notes or call from Maytag regarding my PO# and the replacement. I had to wait for 1hr and 15 minutes for the Home Depot to be able to connect to Maytag customer services and we had to wait for their supervisor to approve the replacement. I was so disappointed later to hear Maytag supervisor telling Home Depot that I had to wait for the repair and they did not approve the replacement. Its really a waste of time and money to buy Maytag products and they dont honor what they said to customers. Once you pay them they take your money and dont really care whether their product is worth the money consumers spend on them. In general its a rip-off!!! Stay away from Maytag products if you dont want to waste your time and money!!

We bought a Maytag washer and dryer in April 2012. A few weeks ago the washer while it was spinning out, it sounded like it was metal on metal. Sears came out and said the transmission and the tub had to be replaced and the tub was created to the transmission. My husband and the only ones living in home and I sort my clothes, so I dont have big loads. I contacted Maytag, their answer was its out of warranty so we are not going to do anything for you. Anyone who buys a Maytag Washer, watch out what youre getting.

I purchased my Maytag Bravos from Lowes in early 2014. A few weeks after the motherboard fried and Lowes replaced it with a new one. Within my 1 year warranty the new machine had another fried motherboard. Maytag replaced it for free. Now less than a year later the motherboard is fried again. Needless to say I just purchased another washing machine. Definitely not a Maytag. Now I just have to deal with a dysfunctional piece a junk for a few days until I get my new one. After reading all the complaints on here and other sites, Im very disappointed with Maytag. These machines are obviously lemons and any good company should recall them. Mine will be going straight to the junkyard. I have no interest in having a washer that breaks down every 10 months. Definitely the last thing I will ever purchase from Maytag.

I am not complaining at all about my dealer. I am complaining that I also am like the many others with the French door fridge/freezer. The bottom of the freezer freezes up and water pours all over the floor. I thought that Maytag was a good appliance, but also had problems with the pump and drain on my washer. Both of these are only 2 1/2 years old.

Bought Maytag dishwasher model number MDB894995BB3 serial # F41103073. About 2 months out of warranty the control panel went bad. Contacted Maytag. After quite some time they agreed to pay for parts. After some more conversation they also agreed to pay service and labor. This was on the first day of August and Maytag scheduled a repairman for the sixth of August. When he arrived spent five minutes and said he had to order parts. The control panel I had already told them was bad. Now here I sit waiting for part to arrive. No more Maytag or Whirlpool for me.

My husband and I purchased the Bravos XL washer and dryer set about a year ago as our first big washer/dryer purchase for our new home. We spent about $1200 on the set from Home Depot. I very much regret this purchase as the washer never gets our clothing clean! The washer never puts enough water in the basin and the clothing comes out with strange white smudges EVERY. SINGLE. TIME.I have tried changing detergent, I have tried skipping fabric softener, Ive tried rinsing out the dispenser thinking it was residue from old soap. I dont know what it is, but what I DO know is that the clothes go in without the white smudges and come back out with them for every load. I have to run a second rinse cycle just to get it off, which means Im washing for at least an hour and a half. I DESPISE this machine and its costing me more on my water bill.Additionally, the dryer isnt much better. It constantly shuts itself off even when its not on energy saver mode, with the little red light going on for air flow. Ive checked the connection and dont see what the issue is. If I have a big load such as blankets in there, I have to dry them all individually for almost an hour just to dry my bedding! It simply wont stay on to dry a full load. I very much regret my purchase and wish Id gone with something simpler and cheaper as it would have done a much better job with my laundry. Lesson learned. Dont waste your money on Maytag.

I have had my Maytag refrigerator for eight years and it is best one I have had in fifty years. It is dependable, quiet running and easy to maintain. The ice maker is wonderful; it always has ice ready even on the hottest summer day. If and when I ever need to purchase another refrigerator, I wouldnt hesitate to buy another Maytag!

We bought a brand new Maytag refrigerator online model # MSD2660KES and it arrived dead. The first Maytag tech that was sent said he does not recommend us fixing the problem because refrigerant leaking will happen every few years. We were not able to return the refrigerator, so we opted to let Maytag fix it. Here we are 2 years later and sure enough, the refrigerator has stopped cooling. We are out of warranty period, so the service call cost us $65.00. The tech told us this time its the compressor and replacement would cost $650.00 to fix. We are not wasting any more money on this piece of junk.

Purchased new about 3 years ago, doesnt clean, ties clothes in knots, leaves white spots from softener that doesnt get wet sometimes after cycle, some areas are still dry after untying. Now error code 51 keeps appearing, service man 4 times replaced rps sensor as directed, nothing changes. Need a chain to drag behind truck, no technical support from Maytag or whirlpool. Old ones of 20 years still worked good, gave to niece. Lucky her.

The washer drum fills up with very little water, very little. I can do an entire load of laundry and the stuff on top doesnt ever get wet. Went on Spring Break in Florida and a month later our clothes still smell like the beach. Grill out, and I smell steaks the next time I put on the shirt. Stain your clothes in any way, its there forever unless you hand wash it first.To get it to work at all, each time I have to start the wash cycle (I leave the soap out just to save it for the next start), let the drum fill with water, pause it, get all the clothes wet, then cancel the cycle. After it drains and the machine is off and full of wet clothes, then start it all over again adding soap this time. On the second try, set at deep cycle, it will add enough water to cover the clothes - Im guessing because it senses more clothes because the clothes are now wet from the first, cancelled cycle. During the wash cycle, Ill open the lid and robustly move everything around, almost hand washing. #Handy. The dryer is fine, Im keeping it. The washer, cant return it - been three months of this frustration (kept believing it was me, reset it multiple times, change the settings, tried everything). Im buying a new one and throwing this junk out. $700 lesson.

We purchased the washer and dryer in June 2009. This past weekend, I noticed that the washer was leaking. The price to fix it is half of what a new machine will cost. I am very disappointed in Maytag. When I purchased the machines, I thought I was purchasing a quality product. Ive had paid much less for washers that last longer. Needless to say, I am shopping for another washer this week and it will not be a Maytag or Whirlpool. They are pieces of junk!

We purchased a Bravo Maytag series top load washer from Sears in June 22nd 2013. See receipt for verification of sale. It seemed to be alright and we were hoping to be a lucky consumer, but now it is January 2015 and today I could smell smoke along with a weird smell (like an auto repair shop smell). I immediately was concerned about the entire house catching fire. Luckily I figured out the smell was coming from the washer and was able to pause it, stop, and then turn off. We are not happy. Our whole main level smells awful. And Im pregnant so this is probably not good to be inhaling. We are looking for recalls that may be out but weve only seen front load recalls not top loaders. When we bought this it had great reviews, but now it appears there are so many complaints, so my question is: Why isnt Maytag doing something about this massive problem?

We bought this Maytag washer 3 mo. ago and now need work done on it. We were told that they could not find anyone willing to come work in this area. We live in the Mississippi Delta, 30 miles so. of Greenville, 50 miles no. of Vicksburg or 90 miles from Jackson. So I guess the Maytag repairman is not just lonely anymore, he doesnt exist.

I do not like this Maytag Centennial Washer at all, I have had it for a year and a half and it just does not perform good at all. Most of the time the clothes still come out with dirt on them but what I am most mad about is the fact that it keeps leaving bleach spots on my clothes, several washes after I use the bleach. I will definitely not recommend this washer to anyone.

The Maytag Bravos Washer we bought had a stinky odor we couldnt get rid of. We found that clothes had gone over the basket and lodged in the filter above the pump; end of stinky smell. Later, we found that pennies and other small items had slipped into the fins of the drain pump and ground them off. The filter does not keep out of the pump and is not made right to stop damage. I called a local Maytag dealer who said he had a lot of similar complaints. I called Maytag who stated they have no registered complaints of this type and had no fix for it. Avoid the Bravos line of washers - they are not made right and Maytag will not admit it or help you. Bravo for Maytag who are obviously not going to act on it. Make a formal complaint and find if someone has a lawsuit you can join!

Maytag refrigerator model MFF2558VEM9 purchased in November 2012 from Home Depot for $1329 suddenly would not maintain freezer temperature under high 20s in April 2017 (4 years, 5 months). Repairman says it has coolant leak, probably due to corrosion within the sealed system. Cost to repair - $1500. Repairman says this is a common problem.

I purchased the Maytag Washer & Dryer $1891.14 with Extended Warranties Model numbers: MHW5100DW0 & MED5100DWo. In September 2014 from salesman ** at ABC Warehouse for my Wife as a Wedding Gift. The dryer started malfunctioning toward the end of October, it was randomly flashing a red light indicating Check Lint Screen and when this happens the dryer will lock up not allowing you the OPERATOR to dry your clothing. We ALWAYS check our screen before use and clean after each use, so we found that light to be odd. But anyhow we checked the lint screen and nothing was on it nor was it bent out of shape, everything seemed normal to me & my wife besides the fact we spent $1891.14 on BRAND NEW washer & dryer set thats acting weird. I called ABC Warehouse spoke to **. He said Yeah they do that sometimes, you just gotta MAKE SURE YOU BLOW THOSE THINGS OUT MAN cause they dont like it dirty. I explained to him we keep it clean then he said the screen might be slightly bent. He went on to explain how he seen that happen a lot, I just said uh huh uh huh yeah yeah. So now its like the middle of November and the DRYER Check Lint Screen Light is coming on before every load now and staying on for long periods of time not allowing us to dry our clothing. So I called ** again 2nd week of December this time asking for a new unit. He told me to call the ABC Warehouse Store Warranty Department at 1-800-722-3333. I called and they gave me a number to Master Tech Appliance 1919 Federal Blvd, Ann Arbor, MI 48103 (734) 662-0641. I immediately asked why am I calling technicians instead of new unit when my unit is still under the 1yr factory warranty and in addition too, I have purchased an 5yr extended warranty? They wasnt trying to hear that. So I called Whirlpool 1-800-253-1301 told them the situation and asked for a new unit they said NO and then added by telling me their policies and how many times they can come and attempt to fix my unit before replacing it. I screamed and shouted at them explaining to them that I have spent $1891.14 on a non-working unit for my wife as a wedding gift and I am currently drying my clothes at the local Laundry Mat, they said NO still.So I called Master Tech, they couldnt come out until Feb 3, 2015. My wife took off from work. In the mean time it completely stopped working the first week of January, we had to go to the Laundry Mat every couple days cause we got 4 kids. SMH WOW my wife is pissed, I mean furious. When ** from Master Tech showed up he looked at our unit and said its also not getting hot so he called in to his job they told him to come back and order my parts and to schedule another day to come back. 2 weeks later Master Tech called with the appt. My wife took off from work again but this time they called the day of hours into the day to tell us the parts are on back order and they need to reschedule. My wife was VERY UPSET but we did it anyways. Now remind you are dryer is still out of commission. Were going to the LAUNDRY MAT. Master Tech came 3 days later (my wife took off from work) they literally took our dryer apart (Pics Below) for it to still not work, Master Tech called Whirlpool, Whirlpool told them to order us a NEW SWITCH BOARD. Wow what the hell are you serious? So Master Tech leaves again and orders the SWITCH BOARD. They came 5 days later (My wife took off from work) new switchboard and dryer still not working. Now throughout this whole ordeal Ive been in contact with all 3 companies begging for a new unit and nobody wanted to hear that especially WHIRLPOOL & ABC WAREHOUSE. With Whirlpool knowingly the switchboard didnt fix the issue the first time, they instructed Master Tech back to my home with the same but NEW SWITCHBOARD. LOL WOW I CANT BELIEVE THIS IS HAPPENING TO US. Master Tech schedules yet another day to come by 3-13-2015 & yes my wife took off from work AGAIN just to hear ** say sorry they keep sending me back with the same part and they know its not gonna work but anyhow Im here. He switched out the Switch Board again and still nothing. I called ABC Warehouse and they finally okayed us a new dryer with delivery day of next day, which is today 3-14-2015 and when it arrives THE WHOLE FRONT DOOR IS BENT OFF THE HINGE WOW WOW WOW WOW. Now they say our new will be delivered 3-17-2015 and yes my wife has to take off from work.Updated on April 9, 2015: 3/17/15 ABC Warehouse replaced the 1st broken dryer to only return with another broken dryer, same problem, red check screen light flashing & dryer wont spin. They left here.

I purchased a Maytag dishwasher Model # MDB4949SDE1 from Home Depot April 30th 2015. This dishwasher does not clean the dishes no matter what cycle you use. After 4 hours and 29 minutes I open the dishwasher to find residue on my so-called clean dishes. Every time I use it I have to re-wash or rinse the dishes by hand before I can put them away.I have spoken with Maytag on several occasions concerning this matter. I have used every detergent on the market. Maytag says you have to use jetdry, and liquid detergent which I did and it made no difference. The latest suggestion was that the water from my water heater was not hot enough which is set on 140 degrees. The customer service rep. ask me how far the water heater is from the dishwasher and I replied approximately 14 foot. She suggested I turn the faucet to my sink on before I turn the dishwasher on so that the hot water is present as soon as I turn it on. This also did not work. They sent a kid out today that turn the dishwasher on for five minutes empty and said well everything seems to be working properly. I dont know what to tell you, yet there is soap residue in the bottom of the dishwasher right now. Do not purchase this dishwasher. It does not clean the dishes. It just uses power and water.

MMV5207BAQ purchased in Feb 2009. I paid $512.00. 5-09 Bob Millers Appliance replaced the door because it bubbled. 10-11 Bob Miller appliance replace the door because the handle broke off. 3-12 Bob Miller appliance replace the door because the handle broke off. 10-16 Door handle broke off again under normal wear and tear. 12/14/16 I went to Bob Millers Appliances and was told to contact Whirlpool. 12/16/16 I called Whirlpool, Tina said, yes it is excessive but it is not under warranty and they do not make the microwave any longer and they cant do anything to repair it and they can not fix the issue. I find it how to believe Im the only person who has had this issue. I dont have kids. Its only me that uses it.

I thought washers are supposed to last 10 years or something. 3 years and I have to replace it. I dont know who Im more dissatisfied with - Maytag or Direct Appliance where I purchased it. Just thought I would rant and warn others about this brand. The computer died so it doesnt know what cycle its on. Repair guy said its unfixable. ARGH!

Bought the matching washer dryer set thinking would be energy saving and reliable. Two months after warranty ended it quit, press pause/start button, no reaction. Started looking online and found out this is Maytags Frankenstein. Checked obvious stuff like power supply. Wont be buying another Maytag product EVER. Dryer still works but washer dead. Am retired, low income. Cant afford expensive repairs. Maytag ought to be eating this, not the consumer.

I bought a new refrigerator and when I plugged it in would not cool. I called and the authorized tech came and said the compressor was bad and the evaporator was rusted and hoses were greased up. I have now been informed that the warranty was void because it was put in a dental office and not a single home. I said since it was never used I would put it in a house. They said it was void and I was out of luck. I always thought maytag sold good products but this has convinced me to never buy a product from them again. It never worked and the tech said it should be replaced but they said he should never had told us this.

My Maytag Dishwashers (MDB7749AWW1) control panel failed for the 2nd time. I replaced it several years ago, but this time the part cost was almost double. So instead of a recall they jack up the price to capitalize their mistake. The ribbon cable gets rusted at the bend from the steam over time. No Whirlpool or Maytag or any other products they market.

Double door Maytag 3 years old has been leaking water in freezer floor and forming sheet of ice. After reading the reviews, I may decide to buy a different brand. Why spend more money on repairs! Very bad experience!

I purchased this machine (Maytag washing machine model MVWB700VQ0) from Home Depot in December of 2008. When purchasing it I decided to spend a bit more money on the machine, thinking I would get a quality product. For the last two years and 5 months it has only been me and my wife in the house as the kids are in college. Hence, the washer has not been used as much as some would use it. Within the last two and one half weeks the machine started making a horrible growling noise (probably the tub bearing going bad) and then started to leak yesterday. I noticed this morning that there was a large puddle of bleach water coming from under the machine. I called Maytag, which is just a fancy name for Whirlpool, and they basically told me too bad. It is inconceivable that a machine that used to last 20-plus years barely lasted three with only two adults using it. When I owned my previous home in another town the house came with Whirlpool appliances which literally fell apart within 5 years. I wanted to stay away from Whirlpool; however, I did not know that Maytag was owned by Whirlpool. I have received no assistance from Maytag. I am absolutely disgusted with the fact that an American iconic company such as Maytag is producing such garbage. I am going to be forced to figure out and fix what is wrong with the machine myself. However, I do believe this subject should be looked into further and possibly a class action law suit against Maytag for bad customer service since there seems to be quite a few people with issues surrounding this machine.

In order for the machine not to break you have to disassemble the drum agitator during normal use... Very poor design. Mine lasted just over two years. My initial cost was $570... Dont waste your money.

I purchased a Maytag electric dryer Bravo 300 Series in November 2009. December 2011, the main computer board went out and had to be replaced. Do not purchase Maytag appliances. They do not stand by their defective products. First and last Maytag purchase.

I bought a new Maytag Quiet Series 300 in 2005 and have had nothing but problems with it. The internal plastic pieces that hold dishes in place have broken off regularly. The door handle also broke. The dishwasher does not drain all the way every time. Now, the dishwasher will quit randomly before finishing its cycle. Our model (MDB7600 AWB) was not part of the recall, but is a lemon nonetheless. Of course, all of this occurred after our one year warranty had expired. This dishwasher is a lemon and a waste of $400. Well never buy another Maytag product.