My front load Kenmore just fell apart. I guess Im lucky I have had it for 8 years and now its broke. I could fix it but thought it would be better to get a new one. I looked at all the reviews for front load washer and could not find one that had positive reviews. So I went with a top load. After reading all the complaints I might have made a mistake, but its too late now as it was delivered yesterday and now doing the clean cycle. Oh my…what junk they all produce now - a true throwaway society. My refrigerator is still working after 24 years what a gem of a product. Happy days.

Maytag Bravos electric steam dryer purchased 2009 - I have had to replace the door hinges within one year of usage at my expense. The blower belt and pulley had come off twice, the last time about a half hour after the repairman (again at my expense) left. I put it back on myself and if it comes off again, I will use Locktite to glue it on the blower shaft. I figure I will be lucky if this crap lasts a couple more years anyway. No more Maytag for us! What does it take for the consumer to get some representation with regard to lemon laws here? I will take my wrath out on Home Depot here since I have no recourse. If enough people complain, maybe they will stop selling that junk. I also will disregard Consumer Reports in the future.

Maytag Top Loading Washer-We bought this machine a little over a year ago and it is one of the worst products weve ever purchased. More often than not clothes barely get wet and then wad up into a twisted mess which stops the machine. Ive had to restart a load over and over. And, the clothes are not as clean as they were from our former Maytag washer which lasted 14 years. The new washer has to be cleaned at least once a month or it smells. We purchased this washer from HHGregg and they are no longer in business or I would complain to them about selling faulty products. I dont know why the manufacturer decided to remove the agitator from new models. What a mistake! We have decided to get rid of this washer and buy another brand. No more Maytag (or Whirlpool) products... ever!

If the control panel light on your Ice2O refrigerator starts flashing you will learn about the Non-Customer Service of Maytag. The problem is the High Voltage Control Board. Maytag has been aware of this defective part since 2007. At one time Maytag was fixing these at no cost to the customer via a recall. Then conveniently in 2011 the Japanese tsunami wiped out the only plant in the universe that manufactures the part.Now out of the goodness of Maytag’s corporate heart they offer the customer $300 off of a $2300 replacement (Oh, I am so grateful). It is time for Maytag (Whirlpool) to accept responsibility for a defective product and recall this refrigerator with a replacement. In the meantime if you have this problem, my advice is to go out a buy a non-Maytag/Whirlpool product since Maytag/Whirlpool cannot be trusted to stand behind their products. Please share this post with family and friends to prevent others from experiencing Non-Customer Service.

On 8/26/16, we purchased a top-of-the-line Maytag dishwasher from Lowes of Palm Bay, Fl. It began leaking water out one side shortly after installation. Because of a hospitalization, we were not able to report the problem to Lowes until the first part of December. A repairman from Brandts in Sebastian, Fl. came out on 12/6/16 and said it might be the door gasket, but he did not have a new one with him and if it continued, to call back. I called again and another repairman from Brandts came out on 1/3/17. He said it was out of square and he took out 2 screws and said to cut back on detergent because too many suds could cause it to leak (which we find ludicrous). Now it leaks on both sides. This is not a small leak; it soaks the bath towel we put under the door. On 1/11/17 Brandts sent 2 repairmen out and they claimed we needed to cut way back on detergent and put in a capful of salad oil because our water softener is causing the suds which causes the leak. We now use 1/2 teaspoon of detergent and the capful of salad oil. It is still leaking. Our previous Kitchen Aid dishwasher never leaked and we used the recommended amount of detergent in it. We are apparently stuck with a brand-new dishwasher that cannot be fixed. We will NEVER buy another Maytag appliance.

Maytag Refrigerator Model MFI2665XEW6 piece of junk. * Builds up ice on bottom of freezer * Bottom freezer door will not close * Annoying alarm sounds* Water leaks on floor

No motor is available for the Bravos washer machine which is 5 years old! Now the machine is garbage and I need to buy a new one. I thought Maytag was a great brand so I purchased the Bravos but now I understand from the company that no motor replacements are available!! Wtf? Maytag/Whirlpool dont care for loyal supporters so, I am TELLING EVERYONE not to purchase Maytag/Whirlpool appliances whose name has gone for a dump with this latest situation.

We bought a Maytag Dishwasher Model # MDB4709AWW4 about 2 years ago. Complete piece of junk. Just spent $350 on a new control panel. We called Maytag and they told us that our model wasnt under the recall for this issue. The old belief about the Maytag repairman not being busy is a lie. Avoid their products. They are poor quality.

We purchased a complete, upper-end Maytag kitchen package from Lowes. So far, the MMV5208WS microwave has gone out 3 times; it was the magnetron all 3 times. The last time was a few weeks after the warranty ran out. After a lot of discussions with Lowes management, they then took it back and gave me choice of any brand. We picked a Samsung and have had no problems so far.As for the MDB8859AWS dishwasher, it was just stuck under the counter for the first 6 months of its life, because we were in the middle of a remodel and it wasnt plumbed in yet. Once we got it working, my wife loved it. Weve used it maybe 40-50 times since she was still hand-washing small sink-loads of dishes. A month or so out of warranty, it went out. There were no lights on the keypad and everything was dead. We thought it was the main control board, but it wasnt. Next, I tried the keypad, because Ive read many posts about these 2 things seeming to always go out on these models. I still have the fridge and stove, and hopefully they fare better than the microwave and dishwasher.What kills me is when I look at my old Maytag dishwasher and Samsung counter top microwave in the garage; both 15-20 years old and still worked just fine after getting replaced. It has never had a repair of any kind. I went out and spent $639.00 (it was on sale, the regular price was $799) on a ** dishwasher and it didnt even last a year. The microwave was close to $400, and it was on sale. I think my old Samsung microwave cost $79.99 when I bought it. You used to get what you paid for!

I purchased my first Maytag dishwasher and it was recalled as being a fire hazard. I was offered to have it repaired or pay for an upgrade (approximately $200). I chose to pay and upgrade because I dont want a fire hazard in my home. After my paid replacement, I received a recall on the new dishwasher regarding the same issue (different model) and I chose once again to pay and upgrade (thinking that if I spent $700, I wouldnt have a problem). In less than two months of installation, the dishwasher died in the middle of a cycle. Filled with water, I bailed it out and called Maytag. I told them that I wanted a new one and they told me that I was past the replacement period. They sent a service man out and he stated that it was a problem with model # MDB7709AWB2 and serial # F03002958. He said that it was easy to fix and said he had done it several times. So now, within less than 1 month before my warranty is expired, the dishwasher did the same thing--it died in the middle of the cycle and wont turn on. I called Maytag and they told me that they would send out a third party repair company (JD Appliance) but I would have to wait for four days. I contacted Maytag and said that I was concerned about the dishwasher breaking down again for the same problem (bi metal unit blew). This is the second time it happened. Jeremy, the repair man, said that the first replacement was not installed properly and they should have replaced the entire unit. He stated that it was a common problem with that model, as did the first repairman in Dec 2010. When I spoke to a supervisor named Kia at 800-344-1274, she stated that they had no known issues with this model. I said that it was not what the repairman told me as well as the Maytag dispatcher. They both said that the heat sensor (Bi Metal Thermal Unit Part No. W10258275) goes up and has to be replaced because it is overly sensitive. If you are out of warranty, it costs around $200 to have it fixed. I told Kia and she said that it was not documented in her file, therefore, it never happened. I want to know my consumer rights to address this issue. I have paid for (on 3 occasions) a new dishwasher and have continuous issues that cost me money. I want an assurance like an extended warranty, free of charge, for the dishwasher that has already been repaired twice for the same exact problem. I have the original part that was improperly replaced to prove that it wasnt replaced to specifications, therefore, blowing it again. I was told by Kia that Maytag does not compensate or replace their products unless deemed not repairable by the technician. It doesnt matter how many time the same problem occurs. I would appreciate your attention to this matter.

We bought a Maytag dryer from Lowes on 4.23.20 for $567.87. From Day 1, it required us to dry even medium loads at least 2 times and sometimes even 3 times. I have been complaining to my husband since we got it. The clothes come out smelling almost burnt. But if you dry it once, the clothes are wet. And if you try to dry it the 2nd time for less time, its still not dry. So, it takes forever to do laundry. This morning, it sounded like a lot of metal was rattling around. So, I looked inside to see if change was in there, and nothing was in there but t-shirts and socks. It had been drying for less than a minute, but when I opened the door a wave of extreme heat hit my face. Now Im afraid to use it because I think it will eventually burn our house down. And with COVID-19, we do tons of laundry. We cant afford another dryer but may have no choice.

We purchased a Maytag Neptune series washer/dryer set approximately 5 years ago. This is the 2nd time in 5 years that we were told by our local repair person that the drum of the dryer got bent out of shape. This is from normal use and due to a bad design on their end. Maytag refuses to foot the bill (about $350-$400) as it is out of warranty.

Maytags reputation for quality is gone. Our Neptune washer has had mold, door lock seized up and wouldnt open, and now our dryer drum is cracked. Exaggerating your products reliability is one thing - this borders on corporate fraud.

We purchased a Maytag front load washing machine and dryer about 5 years ago. The front load washer is completely full of mold even though I have always followed the directions of wiping it out after each wash, leaving the door cracked, washing the machine with Affresh and even trying bleach and vinegar rinses. When I called customer service they refused to do anything about it. Then the dryer stopped working after 5 years and we had to get it serviced. Now, the door has completely come apart, as in every little piece has come off the handle and surrounding door frame. I have never seen anything like this on the oldest of machines and I have taken care of these appliances. I will never buy another Maytag...

After less than two years the commercial washer we purchased from Lowe’s died. A repairman came out after a week and said it potentially needs a new control unit or computer. The control unit is on back order and we’ve been without a washer for a total of three weeks. The situation still remains unresolved and I’m regretting not going back to Samsung. After 9 years with a Samsung washer, it died and Samsung refunded the full price of the washer. It was a poor choice to choose American. :(

We bought a Maytag range Nov 2013. My daughter has maytag appliance and stand by maytag. We grew up with maytag. But those days are no longer. It is not about quality, it is about how many did we make, how many did we sell. I am very disappointed with my range. I tried several times to use my upper oven, in disbelief my lower oven was heating. This happened so much that I touch to make sure that the Correct oven is on. I also have problems with my knobs for my burners. I could not turn off burner after finished cooking. We had to unplug range and turn off gas, if we did not do that the burner would have remain burning. This very uncomfortable for us.I still believe in maytag. I am sure we have not talk to the right person. There is too much at stake for the company, too many complaints are bad for any business. I too am a victim, very disappointed, I wont give up. I have a warranty with home depot and they have been great. It is not their product but they sold it. I hope everyone with a lemon will get problems solved. We only want what we pay for, even manufacturer when they buy other products they want quality as well, we all do. Hoping everyone will be able to get justice. Thank you.

I have a Maytag side by side. In the first year, the ice maker failed and I had to replace it (in warranty/no charge). In the fifth year, the compressor failed (no warranty) and it hasnt been replaced. Since then, I have been looking at reviews and warranties of new refrigerators. The warranties (unless you want to pay $3,000+) are all one year limited. The reviews are scathing and it doesnt matter what brand. My question is, why dont you/we all get together and file a class action suit and demand millions in damages? Complaining wont get you anywhere with these people; however, hitting them in the pocket book will make them pay attention, especially if the penalty is severe enough.

My Bravo washer will not wash a set of sheets without dancing across the floor. So irritating to have to run in and separate the sheets that have ended up in a ball. The dryer is ok. Except my old Maytag had a loud buzzer that went off when the cycle was done. My new dryer has a dainty little chime that cant be heard if the washer is going. Wish I had my old set back!

The Maytag Bravos XL washing machine has a difficult time getting clothes clean. The glass top allows a person to watch the clothing being washed. After one watches this for 5 minutes, it is quite clear that the clothes are not being washed properly. Clothes frequently end up dirty at the end of the wash cycles. I personally believe the design of the agitator is so poor that it is not capable of moving the clothing around to come clean. The tub is a large 4.5 cubic foot capacity, but because it uses so little water it simply doesnt function as advertised. Often there is residue on clothing, simple stains like dirt marks dont get removed. In addition to poor cleaning, the spin cycle is simply bizarre; clothes are twisted to the point that the wrinkles created during this cycle will not come out during the dryer phase of laundry work. I am completely unsatisfied with my purchase and regret not researching this more prior to purchase. I am baffled that this product could actually make it through quality control at Maytag. I have had one service call under warranty to fix the lid not locking. This repair was completed with satisfaction.

I purchased my first Maytag (Bravo Washer) appliance in 2013 and thought this washer would last me for a minimum of 10 years. It started making noises occasionally right away but I wasnt too concerned until it started sounding like someone was banging on it with a sledge hammer. I waited 8 days for a repairman who told me the bearings were going out and it would cost $400-500 to repair. This is the worst washing machine ever manufactured. My advice is to buy any other brand. Dont be fooled by the Maytag hype. Their quality is nonexistent. I am shopping for a new washer.

MAYTAG REFRIGERATOR SAFETY ISSUE SHARP EDGE Maytag refrigerator model MRT118FFZ01 purchased Feb.2018. There is a safety issue, sharp edges. Maytag has been aware of this for over 1yr from customer reviews. I went to consumer affairs.com and there are numerous complaints on products/customer service. I have been asking for a replacement door since Feb. On Sept. 7th I cut the palm of my hand on sharp edge, drew blood, no stitches but I was very upset. Called Maytag, transferred to the safety dept. sent out service tech. He reported that it was a safety issue, very sharp edge, he had to put duct tape on corner to prevent any more injuries! He requested that new doors(freezer&refrigerator door) only be sent, I do not want/need the whole unit replaced. Freezer door has sharp edge also. I have numerous emails to/from corporate office begging since Feb. for a new doors so that this would not happen! Maytags solution is to buy back refrigerator or I should pick another model. Neither is a solution for me. I picked this model for a reason. I asked them to provide me with the simplest solution which is to contact factory where it is made, red flag it, talk to manager, quality control check to see that there are no sharp edges before it is shipped to me. They refuse to do that 1 simple common courtesy, customer service request! They cannot guarantee that door will come without a sharp edge! My model is not the only 1 with this problem. I talked to salesman & model in store has sharp edge & in the reviews the same model had sharp edge which was submitted over 1yr ago! So Maytag has been aware of this safety issue for some time now but chooses to do nothing about it! I chose Whirlpool because of the name, I thought it stood for quality & above all excellent customer service. Was I wrong, found that out thru numerous phone/email conversations. They just dont care! Is it too much to ask Maytag to give me a refrigerator with no safety issues?!!! I have talked to Aaron in the corporate office, he was no help at all. His # 866-817-5404 ext **. I have all the emails to/from him. Please help, I want this same refrigerator, only model that would work for me. Now that I have had personal injury & have spent so much time/effort, aggravation since Feb. trying to have them do the right thing I feel that I am due monetary compensation. Bottom line this complaint is concerning a safety issue & horrible customer service from the call center to corporate offices! The Maytag name isnt what it used to be known for, quality & service.

Maytag Dishwasher with model number MDB6701AWS and Serial Number 41687985NJ.It does not clean dishes like it should. We tried every possible way to set control settings, and still the dishes come out dirty and spotted. Also, it doesnt dry like it should. We had a Kitchenaid before we moved and it worked great.

I purchased a Maytag self-cleaning stove in early 2009. Right away, the oven floor finish started to bubble up. I called Maytag service and was told the part wasnt covered. I let it go since it wasnt interfering with the function of the oven. However, in Feb 2012, the oven started turning off in temps above 350. I called Maytag service again and was told that since I didnt purchase an extended warranty, I would have to pay for the service call, parts and labor. I complained that I never expected their product to break down in less than three years.I had a private oven service look at it and was told the computer part was the problem and would cost almost $300 to replace; or I could just live with an oven that didnt go above 350 and buy a new one when it broke completely. You can be sure I will never, never purchase another Maytag product or any other product they involved with like Whirlpool. I am done with them and their inferior workmanship.

I bought this POS and paid almost 1000. Out the door with tax, hoses, delivery, etc. And it is by far the worst most useless pile of crap I have ever purchased. It just does not work!!! Its a washer that does not wash. It uses enough water to wash one sock and that still comes out stinky.. All my clothes no matter what cycle I use including deep fill power wash or if I add my own buckets full of water to the 1.5 hour wash cycle still come out dirty, stinky, stained and caked with detergent...Hey Maytag heres a hint. You need water to wash clothes and you need agitation to get out the soil, the dirt, the sweat, the stains, the stink and your washer does none of that. In fact I could get my clothes cleaner if I out them in the bath tub and swished them around with a broom stick for 3 mins. How could you go from the loneliest man on earth to the biggest scammer on earth by producing this boondoggle... P.S. Its only me and my wife. We are retired and our clothes are not even that dirty... Its just common sense. No water no action no clean. Ill never ever ever buy anything that says Maytag on it ever ever again and you can bet your life Im telling everyone I know this story.

I was told to at first to just leave the door open, then when that did not work I was told that I should bleach my machine at least once a week which I did. That did not work either. Then I was told to buy the product REFRESH and that would take care of the smell. That did not work either. So I am at my wits end with the stench of my clothes.

I purchased my Maytag dishwasher thru Costco. I did so because I got a 2 year warranty if I bought thru them. The washer was approximately 6 months old and they replaced the pump. Approximately 3 months later they replaced the heater. Approximately 4 months after that they replaced the entire operating/electronic board located in the door. Approximately 6 weeks before the warranty was up they had to rebuild the middle dish tray. Now that the warranty is expired by 2 months the door is leaking like a sieve. Unlike most families we use our dishwasher at least twice daily. In summation I would not recommend this brand of appliances to anyone. I will not pay to have this one repaired.

The washer does not wash properly at all. There is not enough water. The clothes come out covered in lint and still soiled. MOD: MVWX655DWI, SER: C63142093. DO NOT PURCHASE THIS PRODUCT unless you want a ton of frustration!

We purchased a Maytag Dishwasher in 2011. In 2014 I got no response from the control panel when trying to start the machine. Service came out and had to replace the control panel. The cost for that repair was $269.00. It has now just stopped working again. Same issue. After seeing all the posts, I realize that this is a prevalent issue and in some cases a safety concern. If Maytag knows about this issue with their control panels why have they not recalled or corrected these problems! Needless to say, I will never trust this company again!!! Model number MDB7749AWM2.

We have only had this Maytag Washer for 3 1/2 years and the bearings went out. There is just my husband and I in the household and we are retired. We only use the washer once or twice a week. The repairman said the whole tub (inner/outer) would also have to be replaced. We paid $1,126.03 for the machine and it will cost $700 to repair it. Needless to say we will not repair it but will buy another washer. We have always been satisfied with Maytag appliances until now. We probably will not buy another Maytag appliance due to this event.

I bought the Maytag Bravos XL 5.3 washer because it was advertised to conserve water and it was a good brand, but it was a horrible mistake to buy this washer. The washer barely uses any water to clean properly and it hardly moves any of the clothing. The only thing that does move is the clothes at the bottom while the clothes on the top stays still. After using it for a day, I decided to return it back to Home Depot where I bought it, but they did not accept it and told me to call Maytag to return it. I called and the person who answered gave me different numbers to call. After going through ten different numbers, I finally received someone that could help me and they told me that I could not return the washer. They told me that the only way to return it was if there was a mechanical problem with the washer. It is extremely frustrating because I paid over $800 on this washer and now Im stuck with this garbage because I cant return it. I recommend everyone to not buy this washer otherwise youll get the same problems I am getting. I have to manually stop the washer and move the clothes by hand.

Here recently I got a bravos washer x series because it suppose to cut down water usage. Well that it did. Now going on 7 months of having it now its starting to act up like when the cycle is done it will lock again and repeat the cycle all over. I use the normal or powerwash cycle and here recently how its suppose to sense the load and then start spraying the clothes with water and detergent. Well not here. Lately it still senses and spins and then starts filling up like its on the bulky/sheet cycle but its on normal cycle and it doesnt fill all the way up - just 4 or 5 inches of water. So I dont know what is up with this piece of crap and why its acting this way. Other times it will work fine on the normal and the other cycles but now its just acting all crazy.

Maytag Dishwasher purchased for $634 on 7-6-12 from Lowes. Control panel malfunctioned in August 2014. Started leaking in April 2012. From the online comments, I am trashing this machine. It is not worth fixing it and having it malfunction again. Maytag will not say anything about this, only offers a repair person out to fix. I am very disappointed that my hard earned money purchased a sub standard machine. Maytag used to mean reliability. NO more.

I bought my Maytag dishwasher on September 4, 2013. In August 2014 the control panel went out. (Sound familiar?) The dishwasher was still under warranty, so I called Maytag. It took 3 tries to find a repair person who would come out on my schedule. (Im a teacher and cant take time off.) They installed the new control panel, and it working. I tried to submit a review on Maytags website, but my review was denied. I guess they didnt want to hear the truth.

I bought this washer (Bravos Washer Model MVWX655DW) in June 2017. My wife and I did plenty of research and only complaint at that time was that it made load clicking noises. We bought it and it worked fine but never really filled with water to a level which would cover the clothes. Today I ran a load and brownish water was seeping out from underneath. When I lifted the machine my floor was covered with old stains which looked like oil or grease. I called a local service company and when they found out which model I had they refused to look at it. They said that particular model was known for having issues and when they fixed it, something else would go. They recommended looking online for reviews and calling Maytag.I did so and after explaining the situation to Maytag, they offered to send a technician to look at it to diagnose, not free of charge of course. While I cannot tell you avoid a particular company, I can say MY family will never buy Maytag again. If a washer is well known for having issues within its first 3 years and a company will not try to make it right simply because theres no recall on it I will spend my money elsewhere. Seems fishy that this machine has a ton of 1 star reviews within the last two months and Maytag does not want to eat the cost of servicing their junk.

I have a 2 year old Maytag Dishwasher (barely used - it is a weekend house) MDB7749sbm1 and the control panel went out about 2 months ago – I followed another person’s advise of hitting normal and heated dry buttons 3x quickly and that seems to wash the dishes – not sure what cycle it is on because all the lights go on including 2 hr delay. I called Maytag and they kept me on the phone and hold with multiple agents for 34 mins and finally agreed to send someone at no cost to see if the problem can be fixed with no cost to me. I will keep you updated.

I bought a Maytag Top Loader March 2021, this washer machine is the worst ever. It doesnt clean your clothes, & your clothes stink horribly. BBB and an Attorney needs to compensate for our all buyers.

Got woken up to the sound of my refrigerator ice lid flapping. Boy is it loud! Called Maytag and found out it was a recall so they will fix. They set up for someone to come out to fix the following week. That was a flop because they did not have the part. I waited 4 hours for someone to show to find out that Maytag scheduled the appointment for nothing - not only did they NOT have the part but they did not have a clue as to when it will come in. Time is valuable! Here we are 5 weeks later and my refrigerator is still flapping and loud. Has been calling Maytag for them to say that the part has been expedited. Well it has been expedited for more than 3 weeks now! Today they say that it will be another month before the part comes in! Not Good! This is such an inconvenience and Ive lost a lot of sleep over this flapping noise. Its an embarrassment when guests come over to our home! Tired of it!

As many other reviewers have mentioned there is a defective control panel in the Maytag Dishwasher series MDB 7749. I too purchased this model at Home Depot and did not buy the extended warranty. The serviceman indicated that this model is known for its defect yet Whirlpool who owns Maytag does not have it on its recall list. I wrote to the President twice in Sept. 2017 without the courtesy of a response and now learn that he retired effective Oct.1. Is there no-one to answer his emails or is it more likely they really dont care. Sears just dropped them and who knows where their new president will lead this company. Be aware that this model dishwasher is defective and they wont replace the control panel. Too bad as once Maytag before Whirlpool bought them out, was a good and honorable company.

Washer is Broken After 1-1/2 Years: Yes, the code F51 has come on quite often. Now, my washer does not work at all! Does not spin out, makes thumping noises even though I have taken good care of this machine. It cost me quite a lot of money and thought that this was a wise decision. It’s broken after a year, unbelievable! Also, clothes don’t get clean. I had to wash 2 - 3 times. The clothes wrap around each other and the machine does not clean them well. It’s a horrible machine. I have not called Maytag (Whirlpool) yet as I see from the comments that they will not stand behind their machine. I dont know what to do!

Bought mdb7609aww2 dishwasher in 2010. Now I cant use it as it will not start even though the panel lights of my selected wash cycle work. I looked up on internet how to reset it, but I only get a half cycle. Called customer service and for $269, I can get it fixed and get a one-year warranty. Wow, what a deal. Might as well get a new dishwasher. Joining the lawsuit. It is about time corporations take responsibility for defective merchandise, not make money to correct their mistakes by charging customers for overpriced parts and stupid worthless warranties. A pox on them.

French door refrigerator w/ freezer in bottom 2 years old. Purchased this model MFI2665XEM7 December 2012. June 2014 had repairs to freezer. Freezer froze up and bulb stopped working. Maytag covered repairs. September 2014 the ice maker stopped working and having it replaced as we speak. Total cost today for ice maker replacement $216.18. Am I POd, hell yes!!!!!!!!!!!!

I purchased a Maytag Bravo Washer in October of 2011, I had a repair man come to check it since the spin cycle sounds like a jet is revving its engines in the laundry room. He told me that the repair cost is $493.50 to replace the transmission. The machine also has problems with the circuit board. The lid lock goes on and off and on and off so you cannot run the machine. Speaking to Maytag they just kept saying your warranty is over and we dont offer any assistance on the repairs. The machine cost $530.00 in 2011 and they think its reasonable to have repairs more than the cost of a new washer. They said they had no complaints on the model. My repairman advised not to buy Bravo, Cabrio or Calypso models since they all have the same problem with the transmission and electronics. I think they should at least pay for the parts, the transmission is $300. And we didnt even price the electronic part of repair.

This review is for a Maytag Gemini MGT8775XW 30 Freestanding Double-Oven Gas Range w/ 5 Burners. I cannot believe the amount of problems I have had from this $2000+ range. Within just a few weeks of getting it, the paint started scratching off the surfaces nearest the heat. Then, the plastic cover over the digital display and controls bubbled up due to the heat of the broiler being in use. They designed it so that the heat escapes from the oven right in front of the control panel, so when you want to adjust temperatures on the control panel, you chance getting burnt from the hot air every time.The very worst design are the manual knobs for the burners on the front. They are at an angle, and if you look at the oven straight on, you see they are higher than the burner surface. A hot pan that overhangs the burner cooks the knobs. The plastic interior of the knob lacks any kind of heat resistance and actually starts to turn soft, keeping you from being able to turn off the burner at all!Most dangerous of all, the knobs are frighteningly easy to bump, pouring gas into your house. We have had this problem multiple times. Today, my dog must have wanted to investigate the top of the stove, because when I came home, the burner was on, had burnt through a pot on the stove, and was just at the ignition point for an item sitting next to the stove. If I had come home 15 minutes later, my house would be in flames right now. I am having to air out my home as I type this. I am DONE with this dangerous oven and will be shopping for a new one, and it certainly wont be Maytag.

Purchased top of the line Gemini oven a few years ago. Lower oven stopped working. Maytag repair said igniter not installed properly at factory. I contact Maytag customer service to see if they would help with repair cost. Rude response from them... basically saying anything fails after 12 months not our fault. Rejected my request without even asking details about product which model etc. Unilateral rejection. Horrible customer service. I will never purchase Maytag appliance again. Horrible, horrible, horrible. Avoid this company and their products. They do not a good product and they provide terrible customer service.

My Maytag Dishwashers (MDB7749AWW1) control panel failed for the 2nd time. I replaced it several years ago, but this time the part cost was almost double. So instead of a recall they jack up the price to capitalize their mistake. The ribbon cable gets rusted at the bend from the steam over time. No Whirlpool or Maytag or any other products they market.

The only time one can get enough water into the washer to actually get ALL the items wet (or even damp) is to put it on BULKY sheets or HAND wash settings. That is true for any size load whether it be 1 item or 10 items. I prefer being able to get ALL the water I need first, then put in the clothes, then soap, but thats not allowed. First soap, then items, then a bit of water only after you close the lid. They like to say that the spinout dries them which is why they arent damp - but that is a lie when you can smell and see the dirt. I want my OLD STYLE back!

Purchased refrigerator model # MFT2976AEMOO September 2013. First repair was 1 month after purchase. From compressor to moisture build up inside fridge. 7 repairs in the first year. Customer service disgusting. They simply dont care, and do not back their products. Work time lost waiting at home for repairs. Service men come and always have to order parts, which means 2 service calls for each problem. Our service man broke one of the drawers when removing it to do a repair which meant another visit for that replacement part. Continued to have more problems when warranty was done. Just replaced my 3 year old fridge. Could not afford to keep it any longer. Have never been more disappointed with any appliance that I have bought. Will never buy MAYTAG again. Product is inferior.

Purchased washer less than 2 years ago. Loud noise like a jet engine or helicopter in spin cycle. Did not purchase the extended warranty. Called Whirlpool/ Maytag customer service. Was told I could have one of their repair people come out. I would have to pay $300 which would give me the repair and extended 1 yr warranty, or I could get $300 off toward a purchase of a new washer. Are you kidding me? This washer wasnt even 2 yr old and making this horrid noise in the spin cycle. I had to have a independent repairman for Maytag washers come out to tell me it wash the bearing and would cost 3 to 4 hundred dollars to fix it. I said no thanks and after his $90 service call am stuck listening to this piece of junk make noise till it completely breaks. I will never buy a Whirlpool product again or recommend one. Whirlpool you sell nothing but junk.

I purchased a Maytag dishwasher (Model MDB7809AWWI) in Sept. of 2009. In 2010 and 2011, it had dead control panels. The first time, it was under warranty. The second time, it was not, and I purchased a costly service plan to have it repaired. Now, 2012, its dead a third time. Maytag tried to tell me that I could purchase another plan for $289. I informed them that for that cost, I can replace it with a dishwasher that doesnt require costly service plans and yearly repairs. They informed me that their parts only have a 30-day warranty. If theyre not willing to stand behind their products enough to admit that one is faulty, then Im not willing to stand behind them as a company.

We purchased a Maytag MVWB765FW top load washer with agitator to replace a Whirlpool with premature gear case problems (less than 3 years old). Was partially sold by the attractive metal label that says 10 YEAR limited warranty. It is now less than 2 years old and the Maytag selected repairman just diagnosed a failing transmission and of course advised us this is not covered by the warranty. Cost to repair—$ 600. About as close to false advertising as I have seen.I can’t believe that this company would sell such crap and not stand behind their products! But after seeing all these other complaints I believe it now. I bought both washers from Nebraska Furniture Mart and I realize they only sell the appliances but I plan to inform them that if they continue to handle Whirlpool and Maytag products they will never sell another appliance to me or to anyone else I can influence to not buy from them. We as consumers are almost powerless against these manufacturers but if we can influence the stores we buy from, just maybe we will see some improvement.

Eighteen months after purchasing the Maytag Bravos, I had to have the motherboard replaced. Maytag offered nothing except a list of names for repairmen in my area. Now another 18 months later, the washer gets out of balance (this is a self-balancing machine, supposedly) at least three or four times for every load. Since it is all electronic, you cant select a spin cycle without the machine adding more water into the tub. Again, this does not self-correct the out of balance problem. Trying to balance the cloths several times during a wash cycle extends the length of time it takes to wash one load on average two hours. Maytag offers no customer service or customer support. Im sure their call center is not located in any part of the United States. I will never purchase another Maytag appliance.

I love my dishwasher. The only hold back is similar to what I hear about all others and that is that it takes a long time. I love that is it quiet, has lots of room and is easy to use.

I purchased a new Maytag dishwasher model MDB7609AWB1 approximately 2yrs ago from Sears. We purchased quite a few new appliances from them and they are always helpful. Within the first year, right after the warranty was up, it stopped working. No lights on the power panel. I called Sears, out of warranty, sorry. Said they would give me a deal on the repair. Sears came out, replaced the computer. $230.00. 6 months later, it stops working again. I go on line to look up these models and sure enough a lot of people are having the same issues. I did some of the checks that they said to do and found my plastic door latch was broken. A little plastic arm that actuates the switches broke. Should have been made of metal. I replace it myself, very easy, by the way. So I figure, in another 8 months it will prob break again. They run anywhere from $19.00-$30.00. 2 days ago power panel and light, not working again. I called Sears and asked them if they were having issues with the power panels that this was the second time in less than 2 years, and if there were any recalls, they said no. I guess they dont follow their reviews, but according to google reviews, its a major problem with most of them. Maytag, Whirlpool, and Amanda. Ordered a new panel today, again they are $141 from Sears but if you shop, you can get a new one for less than $85.00. If you have any kind of mechanical skills, you can replace it in less than 20 mins. It just seems to me that this big companies have let their quality control go and are more concerned about the profit. There should be a recall on these. Do Not buy a Maytag/Whirlpool dishwasher, they are total junk. Sorry Maytag, you lost another customer.

Im not sure that the guys who designed this unit ever actually tested it. During the wash cycle, if you have something like a fitted sheet it will actually stuff all of the surrounding wash items into the sheet until it forms one huge, round ball. Then it gets really interesting because the vicious spin cycle sends the machine marching around the laundry room and this happens even if the wash has not balled up. I now try to evenly distribute the wash within the tub prior to starting the wash cycle but it doesnt work. So now I grab a cup of coffee and newspaper and sit with my washer throughout the entire spin cycle to make sure that the hoses dont tear out of the wall.

The worst wash machine Ive ever used. It doesnt clean clothes well. It constantly had error codes. Im constantly having to unplug and reset the machine and 4 times out of five it will NOT restart. Not to mention it stinks worse than my sewer. I have to run the refresh cycle every four to eight loads. Ive owned this machine three years. And it has been three years too long. I will go back to a ringer washer or a wash board and have better results.

My wife and I purchased new Maytag dishwasher in 2011. Worked well for 9 months and then control panel went out. We bought a Sears with 1 year warranty. Sears fixed but then 2 more repairs followed with blown fuse and pump motor went out. We knew this was a lemon so we purchased an extended 3-year warranty through Maytag. Well the unit only works for a month or two then we are constantly calling for repairs. We just had the pump replaced a 3rd time and yep you guessed it the unit is loud again so here comes repair 15. The warranty contract states that if the same part fails 3 times, Maytag will replace the unit new one time and voids any further repairs. My wife and I are very frustrated and lost all confidence with the Maytag company. Our old one lasted 14 years and this new one is a piece of junk. The company reviewed my request of unit replacement but was denied for whatever stupid reason. This unit has over 5000 dollars worth of repairs not counting the lost time of appointments waiting for the repair. My wife has had to stay home and wait for 4 to 8 hours an appointment. She has many other obligations to do with her time. Its sad that Maytag does not stand behind their product. Its my conclusion that this company does not want to sell good product, they only want to sell extended warranties. Your products are not reliable if you have to offer warranties. I would like to see if I can get to repair 30 before my warranty expires by March of 2015. Maybe I could then see if 30 repairs would make the Guinness Book of Records on the most repairs done on a dishwasher with extended warranty. That would be something the company could be proud of dont ya think.

Bought the top load water saving washer 3 years ago and paid around $500 dollars for it. It will not operate correctly. I always thought Maytag was the best!! My main complaint is I cannot get no one on the phone to ask questions about what might be wrong with it!! Now Im angry, its like you buy it, its yours, we arent worried about you after that!! I am on a fixed income and no one cares!! Ill never buy anything manufactured by Maytag ever again!!

I bought my Bravos XL 3 years ago after having older model Maytags since the 1980s. My mother also runs a laundromat and SWEARS by Maytag. To say Im disappointed in this purchase is an understatement!!! They have never washed the same as the older models. They twist the clothes horribly! Now Im having issues with all of my dark clothes getting grease spots on them with no apparent cause. I use HE detergent and softener (recommended amounts only) and clean the washer religiously, including the detergent, bleach and softener cups. I DETEST these machines. Also, the dryer never dries unless I run it for 2 cycles, regardless of what setting it is on. Waste of money and definitely not energy efficient when it comes to my water and electric bill, nor time efficient for me since clothes either come out still dirty or with new stains. After this purchase, I would NEVER buy Maytag again!!!!!!

Our new Maytag Bravos XL machine quit just 43 days after being purchased. Purchased from Lowes, but since it was past 30 days since purchase date, Lowes could not do anything to help. Lowes directed us to an appliance repair service that they use. We had to wait another 3 days for repairman to come out to look at the machine... only to find out that a drain pump would need to be replaced, along w/ the diagnostics board since it was not working either. Parts would be ordered & were expected to arrive 3-4 days later. It has been a week later & the parts still have not been shipped out by Whirlpool. We are now on almost 2.5 weeks w/o a washing machine. I usually research & read customer reviews before making a major purchase. However, we had to quickly get another washing machine & dryer, so felt like Maytag was a SAFE choice since I had Maytag several years back. (That Maytag was your basic washing machine w/o the bells & whistles before machines had bells & whistles.) Will I purchase another Maytag again after this occurrence? Probably not. In fact, I am so aggravated & frustrated at this point, that I would love to just throw the machine out in the middle of the street!

I bought a Maytag microwave in Feb of 16. Six months later, last August, it stopped working correctly (light doesnt come on, will not start, continually says open/close door to start). I have been trying for THREE MONTHS to have this fixed. Multiple calls to Maytag have resulted in nothing but empty promises. Calls to the store where we purchased it do no good - you have to call Maytag. We got 6 months use out of a Maytag microwave which we paid EXTRA to have installed. At this point I dont want it fixed. I want it replaced. The Maytag brand used to stand for durability and integrity; now it stands for badly made products and pathetic customer service. Look up my phone number on your computers, Maytag, and you will see all the efforts Ive made to get this fixed.

We have had a Maytag Bravos washer for a while, which has a see-through top load lid and a very small or low agitator. I have to say that I really miss the old fashioned agitator which makes all the clothes being dragged underwater and scrubbed well. We have watched the loads being washed in this washer many times and the clothes are not being swished around very effectively. You feel like you need to help it getting the clothes washed as it seem like it just sit in the same place throughout the cycle. The clothes ends up in big knots around the edges, and you can see the same towel sitting on the top during the 2-minute rinse cycle, never getting completely under water. During the wash cycle, the lid gets locked, so you are not able to open it up to untangle or move towels around if it has gotten unevenly distributed. The wash cycle is very quick, so all in all, Im not sure how clean the laundry really is when its done. We will never buy this kind of washer again.

We have had a Maytag dishwasher for just over a year. The control panel acts up randomly and has finally quit altogether. The design of the handle is very poor as it pulls the control panel away from the door. Will never buy a Maytag product again. This is a very clear design flaw and when we called Maytag they offered no help as we are passed the guarantee.

1st service call about 2 years after we got it. Put around $200 in it. Now broke down again. Service tech quoted $475.00 to fix it. So it was basically totaled after around 6 years. Nightmare kept getting LD (long drain) code. After hours of research I finally called service. Would not drain so I had to wring out a whole load of laundry and bail out the water by hand. Miserable experience!

I have a Maytag Bravos high energy machine that Ive only had for 3 years that has stopped working. After the cost of two diagnosis visits, estimated repair costs are $734 - more than I paid for the machine. As explained to me, these high efficiency washers are in their infant stage, especially when I bought mine in 2010. I feel I have no recourse except to buy another machine. It certainly wont be a Maytag or Whirlpool model! I did research the machines at time of purchase. I thought I was buying a top reputable brand. Guess I was wrong.

We have had Maytag washers in the past, and they always worked well and were reliable. Not so with the Bravos washing machine. It is by far the worst excuse for a washing machine weve ever used. It does NOT clean clothes. It merely ingrains the dirt more into fabric. In four years, we have complained repeatedly to Maytag to try and get some kind of remedy to no avail. Maytag is simply not interested in standing behind their product. So now, after two generations, they have lost us as customers forever and we are telling anyone who will listen; DO NOT BUY A MAYTAG WASHER. They are terrible and not what they once were.

Purchased a new Maytag refrigerator in January 2013. In September 2013, the ice maker stopped working and Maytag sent out a repairman to replace the ice maker. In February 2014, the ice maker stopped working again. I contacted Maytag and was told the refrigerator was no longer in warranty. I told them that since the ice maker was replaced in September the warranty should have covered me for a year from that date. The Maytag representative told me that was not had it worked and asked if I wanted them to repair the item for a fee. I bought a non-Maytag ice maker and replaced it myself. It is now July 2015 and the ice maker is still working fine. I am not a repairman.

Purchased Maytag front load washer model MHW6630HW from Home Depot. Machine was installed 9/15/19. From inception we had issues that have escalated. Machine leaks and makes strange hissing sounds. Home Depot has no record of the purchase in their website now. We tried to return it within days. We contacted Home Depot executive offices and they keep sending Paradise Appliance repair. The repair people do nothing and keep saying we have to come back again for you to be considered for replacement. Home Depot is dragging their feet and we are concerned about the six month deadline. The Maytag does not do an effective job washing and clothes comes out wrinkled. Concerned about the sporadic leak getting worst and doing damage to floors.

Purchased a Maytag dishwasher in 2009 then had it repaired for a leak in 2010 (just past the 12-month warranty); next another leak in Nov 2013 so purchased another Maytag as repair appliance company said it wasnt worth fixing. Now in Feb 2015 it is leaking Again! So 2 dishwashers and 1 repair in 5 years! Both were purchased from Home Depot. I will Never buy a Maytag product again.

We purchased a Maytag refrigerator with bottom freezer and French doors, in March of 2015, Model No. MFF2258DEM00. Its adjustable shelves and adjustable door bins were big points in its favor, at least in my eyes. So far both the fridge and freezer cool fine. The automatic ice maker was never connected, so we obviously have had no problems there. However, within a few months of purchase the bar that supports--and provides tracks for--the vegetable and fruit bins broke. It was replaced, but within another few months it had broken again.This is a DESIGN DEFECT that wont be remedied by replacing the item. The bar, which is plastic, hangs from a thin lip about 1/2 long by 1/8 thick. Thats way too flimsy to support the weight of one bin, much less two. There is no way to repair the bar. The entire assemblage needs to be redesigned and remade from sturdier material. Its not simply the inconvenience of having bins that dont operate smoothly. With their track broken, the bins rest on the glass top of the meat and cheese drawer--and threaten to break that. Theyve already caused the door to that drawer to crack.

I bought the Maytag washer and it lasted 5 1/2 months. I am now going on 1 month without the washer because no one wants to take responsibility for it. Your warranty and service is crap. I will never buy another Maytag product and I will be sure and let anyone that I know that is about to purchase one not to!

I purchased a Maytag energy efficient dishwasher in June of 2010 along with an extended warranty that I keep extending. Cost $ but needed. Issue: Sensor in Panel fails so far every year and needs to be replaced. The repair technician showed me the sensor strip and indicated that this has been a big problem. (At least I have a warranty; however, it is a big pain to have to schedule a service repair person to fix the problem.) Repair (Sears) is EXCELLENT with great customer service. I did contact Maytag and there has been no recall.I own other Maytag appliances such as a washing machine and refrigerator with no issues there. In any case, I needed to replace my clothes dryer and did not select a Maytag. I purchased a GE very simple product with no sensor/bells and whistles. Not sure if I will go back to Maytag in the future - depends upon how they handle problems with their appliances. I would rather pay extra money for quality, durability, and reliability than go through the inconvenience from parts that are not made well enough to hold up.

Just got off the phone with Whirlpool Customer Care after getting the run around between parts and customer service for most of the morning. My issue is with the shelving on my MSF25D2EAS01 Maytag side-by-side refrigerator. The plastic surrounding the glass shelving is disintegrating and they are not admitting to a defective design only that the original part has been obsoleted and a new one is available for purchase (an over $300 expense to replace three shelves) on a unit that is just over 2 years old. I am willing to bet the old part has been replaced with a different design after they realized a substantial number of customer complaints. As an engineer, it is obvious to me that these shelves are poorly designed for their intended purpose, furthermore my work allows me to recommend appliance brands for large projects so I see no reason to recommend Whirlpool or any of its subsidiary brands (Kitchen Aid, Maytag, Amana, Jenn-Air) to any of our clients. Whirlpool quality and customer service is substandard and no better than any imported brand of appliances.

We purchased a Maytag MFI2670XEW6 french door/Bottom freezer refrigerator in July of 2012 through Home Depot and for the past 6 months have had to scrape ice off the bottom of freezer every 5 days or so to prevent water flowing on floor. I see so many exact complaints from people that I am just fuming! Cannot believe this company is not backing their products up with that issue. A recall should most definitely been done. I grew up believing Maytag was top of the line but I am wrong. I bought this to replace a 16 year old GE refrigerator (side by side) which I never had any problem with and now I regret not replacing it with another GE. I havent contacted the company yet as I thought I would check complaint reviews before I did that but it seems that the company is just treating their customers like dirt. To spend $2200 for a refrigerator and have problems within the first 3 years is unacceptable!!! They had better start going good on this problem or face the fact that they will no longer be in business a short time down the road. The best form of advertising is word of mouth and online reviews and it looks like they are going to lose a lot of customers with the direction they are taking.

We purchased the Bravos X set (Model Number: MEDX700XW0 and Model Number: MVWX700XW2) form Lowes in October 2012. When the items arrived and we used the dryer for the first time in the delicate setting, the machine kept cutting off! So, Lowes brought us a new one. At first it worked but then the delicate cycle on that machine ended up not working as well a few months later. I ignored it and used the other settings. Yesterday, the washer broke. The entire basket detached! We were washing a small blanket and sheet set and kept hearing a loud banging sound. I went to check and the clothes were soaked and the entire drum was detached. I am so friggin angry! We spent over 1200 for this set and less than 3 years later, the set is ruined. I am on the phone with Maytag now b/c they need to replace this set or give us an upgraded set. They know that this set had issues yet they decided to still market and sell it. I want to sue!

Purchased a Maytag Bravos washer model MTW6700TQ ON 5/5/2008. Also purchased extended service agreement. This washing machine was only five years old when it started rusting on the top of the body where you load the clothes and fill the detergent. Not in a million years did I expect a washing machine to be rust-prone. Its a washing machine. The service contract doesnt cover dust, mold, rodent damage, and RUST (like rust is an external source). When I called Maytag they were not surprised. They said the life expectancy of their product could be as little as a year and a half. Regardless of the extended maintenance expense I now must throw this piece of junk away. NEVER BUY A MAYTAG. This time I am buying an LG.

Dark clothes are left with residue on them, have to run another rinse cycle to get them clean. Been having this problem since we first got the machine. Anyone else having this problem or got a solution to fix it?

Recently purchased a washer from Home Depot. Machine is now on its 3rd repair. The wiring harness is fired. Could have caused a fire. Now they still will not replace and part is on order which will take 4 weeks to be in stock. I called Maytag and expressed my concerns to which they could not help me as every washer is theirs can be repaired. I really don’t understand what happened to making things right. Very frustrated that they will not repair or reimburse for that matter. Please refund my mom and pick it up.

French Door Maytag MFI2569VEW10 faulty in many ways. We bought our refrigerator 7 years ago. After 2 years the freezer door handle fell off; after 4 years the right front door gasket began to tear (normal usage); after 7 years, it no longer dispenses ice or water. We now have mildew/mold growing around the edges of the door because there is no longer a good seal. Constant cleaning. Additionally, we are spending more $ to keep the refrigerator at the proper temperature because the seal is broken. To repair these items is almost $700 including shipping and tax. This does not include the cost of labor. So after 7 short years, we have a hunk of junk that does not work properly. I am shocked that Maytag sells such an inferior product and we are left holding the bag. Do not buy Maytag. Additionally, our Maytag microwave broke after 5 years. DO NOT BUY!!! Buyer beware!

I purchased a washer in July and its already off track. When I seen it I know it was junk but the sales person assured me it was a good product. 3 months later its off track. No spinning. DO NOT WASTE YOUR MONEY.

Mine is the same sad story as all the others. Bought our Maytag dishwasher in 2013 (model MDB7749) and 15 months later, the control panel went out. We have contacted Maytag and they basically told us it could be our fault it doesnt work, so they wont fix it. Now we have learned that this is an issue that A LOT of people are having. We called their special number for this problem and were told they still wouldnt fix it since we called BEFORE having it repaired. So my question is, how is this legal and why arent they recalling this product? I know that there was a class action lawsuit against Maytag for this problem. Why dont we hold them accountable as well? This is bad business and we shouldnt allow them to take advantage of hard working people like this.

My washer is about one-year-old. Several months ago I noticed a brand new shirt was damaged after laundering. I thought it was inferior material. A couple of months later I saw a similar situation with another garment and started being more careful with the laundry settings using delicate, short, light washes, etc. The problem has happened a THIRD time to another garment. It appears this washer has a hunger for delicate jersey type fabrics. I started reading online and found out at it is indeed the action of the agitator and I need help rectifying the situation.

So far we have replaced the belt. Clothes have never come out clean. High Efficiency... Yeah, we have to put it on extra rinse to rinse all the soap out or wash twice because the clothes just do not get clean. Now it stops right before it drains after the wash. So I had to pull out clothes and use pitchers to get water out before we could tip forward and pull hoses to drain the rest. We checked hoses and connections. All lights work, it did a wash cycle, and again stopped before the drain. Really. All I got was “Didnt you take out the extended warranty?” Well, No I did not. Why would I consider the fact that MAYTAG would need repairs within the first 3 years. Its not like I do a lot of wash. Or have big bulky items. I have a laundry mat close by for that stuff, because it wouldnt get it clean anyway. Never again…

What happened to the days of buying a washer/dryer and having them for years! To spend a thousand on each and have holes in the bellow causing dirty water to Empty on your floor. Not once replaced, not twice, 5 times!!! Now Im looking to buy another. Old school for me...

Control panel start button failed 55 weeks after purchase and installation. Model no. MDB4709PAW. Repair costs for labor and part totaled $298. I have since found out that Maytag dishwashers with this type of control panel are faulty and fail often within first 3 years. Purchased at Johnnies Appliance, Glendora on 6/14/14 NJ; ticket no. **.

I purchased the Centennial Commercial Technology washer in June of 2013. In the last 2 1/2 years it has been repaired 3 times. The transmission had to be replaced twice. My household consist of two adults and definitely it is not overused or overloaded. The washer currently is not working. Consumer service cannot schedule an appointment for repair for 2 weeks. Previous repairs took approximately 2 weeks to schedule a service appointment and it took another week to two weeks to get the part in and washer repaired. I have decided to consider this an expensive learning experience and will not purchase Maytag products in the future!

I bought a Maytag front loader washer and dryer, plus the pedestals for each. In last August of this year the washer just stopped in the middle of a wash cycle. I placed a call to the customer service. The tech diagnosed and placed an order for a part and set an appointment for two weeks later, with a time window 1 to 5 pm. The person called at 5:30 to tell me he had an job before he could get to me. I had taken the day off to wait for him. I called and they ended up rescheduling, for two more weeks.. Tech came ordered different parts, tech did not show up. Tech came out again ordered new parts. Next week he arrived wrong parts. Washer still not extracting. New tech, new parts, new appointment, this was what happened throughout September and October. Tech was not happy with his job, stated that to me, would not do anything but install part, even if it didnt work. He took parts with him. The washer still not extracting. Last Thursday he didnt even have all the parts, made the decision to replace machine without discussing it with me. Told me Sears would call me in 48 hours. Received call today Tuesday. Go to Sears to have it replaced. None of the machines they offered are compatible with mine. I will have to purchase the pedestal for the new machine, plus pay the overage to get the comparable machine. Service appointment people were horrible, cold and rude. Sear store at the mall where I purchased my washer said that it was not their problem. Once we sell it you are in their hands. Have had Maytag for over 30 years. Will never buy it again. Will never buy at Sears again. Too bad I have to replace my washer with something from Sears. Not enough space to write everything I have gone through, the lost workdays, the extra expense of having to go to the laundromat, the stress of dealing with incompetent people and techs.

The machine dries out the clothes so tight that they are full of wrinkles. I am so dissatisfied with this machine, I spent almost $600.00 for this and this is what I get. I also end up with fabric softener all over the clothes. I use the Downy Ball and I just took out my black pants to find blue all over them. I contacted Home Depot where I purchased the machine. They said to get a hold of you. All I want is get a different machine, not an HE. This is beyond anything. Someone should have to put up with, can you help me?

Dryer needed to be serviced within 2 months. Drum seal fell out. Service was no questions asked. Fixed promptly. Washer works fabulous. Gets clothes clean. Surprisingly quiet. You do need to keep up to the sensors on the dryer. Must be wiped with rubbing alcohol to keep performance.

I purchased this $900 Maytag washer from Home Depot in Oct. 2010. Now, after Ive just paid $129 for a service call through their designated repair service, I was informed it will cost $700 to fix this washer. I use the washer on average of three times a week. Its unbelievable that this type of crap is sold by Home Depot and that Maytag warranties will not cover repair as one year has passed.

Bravos mct. Unbelievable, this washing machine is terrible, no water. The water level doesnt even cover 6 items. Have to wash triple the loads of my old washer just to get the clothes clean. I have to go to the laundromat twice a month. I shouldnt have to do that. Almost want to fill the washer with water, but dont know what will happen. Very unsatisfied with this washer.

I PURCHASED A WALL OVEN ABOUT 4 months ago. Used the self cleaning, oven blew fuse and some other part, had to wait for almost 2 weeks for repair because of self cleaning liner is now peeling and leaving fine particles. Maytag said it was ok, they would not replace, the liner doesnt have a replacement part so Im going to have to buy a new oven to feel safe for my family meal.

We just had the same problem as most of you have posted. The control panel malfunction. Model MDB7749SBM. Our issue started after only 18 months when the dishwasher would start on its own and/or cancel a wash on its own. I think this is a major issue if a home appliance can start on its own from the off position and run through multiple cycles. I think this could be dangerous if you are out of town. Our cost to replace the panel was more than 1/2 of the original purchase price. This is a major defect and should be handled by Maytag if they are a company with any integrity.

Bought the set at Home Depot. The gear box went out after 2 1/2 months of use. I called the manufacturer warranty site and spent close to an hour on the phone then was given an appointment to have a service repair person look at it. Two days before the scheduled service call they called and said they would have to move the appointment out by a week. After diagnosing the problem, oil all over the floor and stained clothes from the oil, was told it could be up to 2 weeks until the part arrived and installed. So my warranty is being used up while the machine is out of service for a month. Beware of buying a Maytag!!!

Purchased a new Maytag washer from a local Hardware store chain. Waited 3 days for delivery. Old washer was hauled away. Started using new Maytag Centurion the same night it was received. There was a funny odor coming from the washer that was discounted as new equipment smell. Saturday the Maytag Centurion washer was leaking some odd lubricant that had the same odor as the mentioned new equipment smell. Since this lube had been leaking out in close proximity as the liquid detergent my wife used a towel to clean it up. This towel went into the laundry with other clothes.Now Im concerned that whatever this oily stuff is, it’s in all of the clothing that was washed with the towel. Since I live on the West Coast and Maytag only answers the phone during the week Eastern Daylight Time I will call (2 days) after the fact. You might do well by finding out what this lube stuff is before you take it home and how youll have to deal with it once it leaks.

I have a Maytag MEDC200XW3 model. Good price reliable and rugged. It washes all the way from my delicates to my husbands heavy fire protective clothing with no problems. Holds lots of clothes with no issues either!

I purchased Model #MHW563HW Frond loading automatic washer a little over 1 year. The options are not for me. The quick wash is way too short 20 minutes, all the rest of the options are 51 minutes to 2 hours & 57 minutes! If you wanted to add some extra minutes to the Quick wash you are out of luck. Normal wash is 55 minutes but can last much longer, it takes forever for this machine to balance which adds time to the process.I had an LG front washer before this one and when the clothes came out they were almost dry, not this washer, they are very wet. Then there is the horrible odor that comes after you use it, Ive tried drying every area making sure there isnt a drop in it. Still the stench is unbearable. Yes it has a Clean Washer with Affresh option which takes an additional 128 minutes and you have to do it at least once a week! Thats a LOT of wasted energy. That just doesnt sound efficient to me, washing the washer. Why??? This washer had great reviews which I read, not one mentioning these issues.

Major issues with the Aqua Lift Range. Takes forever to preheat the oven, 15-20 minutes to reach 375 f- 400 f. Aqua clean cycle not efficient and does not clean at all. The stove top is impossible to select and keep the heat consistent. When adjusting the heat up or down when you slightly move the dial it overreacts. When moved the heat sways may more than selected. The fridge works well but the bottom drawer is way too flimsy and it wont last a long time as it will crack. This is our first purchase of Maytag appliances and it will be our last. Our old 10-year-old stove worked much better than this one. Sincerely, Russell ** & Linda **, e-mail= **

I bought my Maytag Bravos washer and dryer set about 4 years ago when I moved into my home. The performance of the washer has always seemed mediocre. Despite using the correct HE products, clothes dont get as clean as with other washers I owned. Many times the washer becomes unbalanced, gets the UL code and I need to move my clothes around to get it running again. A few months ago, the washer started a new behavior: stopping during the initial fill cycle and displaying an F1 error. I soon figured out if I hit cancel and then start again several times, it would resume filling and proceed with the cycle. Over time, I had to repeat it more and more. I read about other complaints and suggestions on the internet and tried pulling the plug for a few minutes to reset the control panel as well as turning off the breaker to reset the machine.After troubleshooting the problem for 15 minutes or longer, the machine eventually runs. Then I can run subsequent loads with no problem. After a week or longer of doing no laundry, when I try to start the machine, I need to go through the entire process of canceling the wash load and terminating electric power to reset the machine. I have called Maytag/Whirlpool and got unsatisfactory answers. I only wash two to three loads of wash about every ten days and sometimes even less. The 800 number for Maytag was automated and would only schedule a repair without asking about the specific problem or being able to talk with a person. There was no way to cancel the service call scheduled and I had to call another 800 number to finally speak with a Whirlpool representative who tried to help me. She connected me with A&E Factory Service to cancel the service call.Both representatives stated that most likely the control board is the problem and the cost for diagnosis would be $130 plus the cost of parts, which could run from $200 to $400 since Im no longer under warranty. I canceled the service call as the cost of repair would be easily be almost half or more of the cost of purchasing a new (and different) machine. This is the electronics module, something that shouldnt be worn down or broken by use or even user error. This is an integral part of the machine and if it has a fault (which it clearly does), the manufacturer needs to stand behind it and help the consumer. The customer service manager even admitted that models with other model numbers had had similar problems and a free control board was sent to those customers. But my model was not in that range.”I had purchased a Maytag Bravos dryer at the same time as I purchased the washing machine and the dryer had a problem within a week of the warranty expiring. A service repair person came to my home to repair the dryer as it was barely a year old and I did not use it for several months that year (due to other reasons). From the volume of complaints Ive seen online, the Maytag Bravos washing machines should have been recalled and repaired or replaced free of charge.

Maytag Centennial Washer - If a wash load becomes off balanced, the machine stops. No signal or buzzer or anything to alert me to this. It happens all the time and wastes a lot of my time. Here I am thinking that the wash is going fine only to find out 2 hours later that it has stopped. Anytime I wash more than 3 items, this happens. I will never buy one again and I am telling everyone not to buy. I will be purchasing a good old fashion washer with a dial gauge so I can spin it any time I needed.

After one year of service from our Maytag Jetclean Plus Dishwasher with Toughscrub the circuit board went out. I have been seeing and hearing other people complaining about this problem. We purchased this device based in large part on Maytags reputation for reliability. I am not happy with this machine. I will complain to the company and write another review based on the results. I suggest Maytag goes back to the old knobs until they can assemble and protect the circuit board, which I believe was damaged by heat and moisture.