Purchased the Maytag Bravos upon recommendations from Lowes and Home Depot to replace a 20-year Kenmore that finally died. Since the Maytag brand was always considered to be the top of the line washers, we purchased the pair. About a week ago during the spin cycle I thought that a 747 was taking off in our laundry room. Called a local appliance repair service who said that there had been numerous issues with the Bravos series and to call Maytag to inquire about a recall. After 45 minutes on the phone with a very sweet naive young lady, she told me that the new models did indeed have a 10-year limited warranty on parts. However my 3-1/2 year old washer was not grandfathered into the warranty. I could (a) pay the $150 service charge to have someone come to inspect it or (b) buy a new one. I will be purchasing a new one but it will not be a Maytag or Whirlpool product. Now we know why the commercial for the Maytag repairman is not running... Hes now very busy working on their broken products.

Im have finally given up and purchased a replacement for my Maytag Bravos XL Top Loading High Efficiency Washer! The Maytag was 2 years old and I have ALWAYS had trouble with it. My towels became sour after 1 or 2 uses (sometimes they smell sour even before use!). My dark clothes ALWAYS came out of the wash LOADED with lint. I researched online to determine whether these were common problems and found several sites with suggestions such as: dont use more than 1-2 spoons full of high efficiency detergent (which recommendation I followed), Use white vinegar or liquid fabric softener. (I tried both with only minimal results.) ALSO use a dryer sheet in the dryer (I did this but it seemed like a waste since I was already using fabric softener in the washer). Dont overload the washer. (I didnt, but if I couldnt fill it, then why did I buy a washer with such a large tub ?!) Clean the washer monthly. (I faithfully did so, and tried alternating Affresh and bleach to see if theres any difference in the result... not really. Make sure you are fully drying the towels (I ALWAYS DID!).We had a Sears repair technician come to the house the last time my frustration level was overflowing and she only made me feel like an idiot, repeating some of the above recommendations and insisting they would solve the problem -- which, if they had worked, would have precluded my need to call a repair technician!!! The repair technician provided no other service or ideas to fix the problems. My husband decided we should go back to the tried and true agitator-type washer... bye-bye, Maytag Bravos.

Every time I do a load of wash, it comes out looking like I slept in it. It is so wrinkled you cant even iron it all out. If the load gets off balance, you have to wring it out by hand because you cant get it to spin again. I did a load of flannel sheets and it went off balance, wringing sheets out by hand is enough to make a person want to send the machine back and get an old-fashioned wringer washer. I hate this machine without an agitator. I have always used a Maytag washer, but I would not recommend this to anyone.

The stove functions are excellent and the temperature of the burners and oven causes the food to cook even. However after about 6 months the heat from the burners causes the coating on the stovetop to burn like its baking and it cant be cleaned. Now the coating around the burners is horrible and burnt.

The HE version of Maytag washer leaves the clothes smelling bad. There are suggestions to remedy this, but why do these type washers cause this? The suggestions dont work. No more HE washers of any brand.

I bought a Maytag Washer in October of 2012. So far we have had to have repairs to it (4) times. The motor falls out. We are very dissatisfied with the product. We have always purchased Maytag products and fee we should get a new washer. The warranty is up in one month. If there is anything you can do to help it would be appreciated. A $1,000.00 for a washer is a lot of money for something that does not work and takes a week to get a repairman. Thanks.

We had a Whirlpool stove/oven for many years, and it was finally time to trade it in. Everything about that unit was good. While shopping for another Whirlpool, the sales rep told us that Maytag and Whirlpool are one and the same. That we found, is false. An important feature for us in an appliance is the self cleaning oven. The Maytag oven had to be leveled four times after it was installed, in order for the self clean feature to function. The self clean part is only a small indented portion of the bottom of the oven, not the entire oven. And even that does not clean. After going through the dealership service about this problem, I contacted Maytag. My final frustrated summary to the rep was that I understand that we bought a lemon, and you are not going to help us in any way. I just want to say to anyone considering a Maytag stove and oven, raise your standard. If you choose Maytag, you will only be disappointed. I am.

I found this washing machine reliable for over 10 years. I paid more for this brand but it was worth the extra cost. I found this washing machine Simple to use. I would recommend this washing machine.

We just replaced our 20-year-old washer and dryer for a new Maytag Bravos set. The Home Depot staff convinced us that top loading units were of good quality and reliable. We were fairly satisfied with our expensive purchase when our washer stopped spinning. We are just past our 1-year warranty of course so we called the service department. A young man in a beat-up pickup truck showed up and spent his time reading the manual that was hidden under the washer. His best guess was a $300 part plus a $100 fee for him to show up. So to repair a less than 2-year-old machine is $400. Im tempted to buy a different washer. It wont be a Maytag, unless you can convince me otherwise. I give you credit for great advertising! I was convinced that Maytag was a good name with limited repairs.

I purchased a Maytag Bravos XL washer and dryer at Best Buy (Pacific Sales) in March 2013 at Best Buy. I also purchased extended warranty on both machines. A few months into owning the machines, the washer started giving us a UL error light. It wouldnt finish the wash cycle and had to be restarted multiple times before it would do so. I called Best Buy and they sent out a repairman. He said the set-up cycle had not be run correctly by their own installation team (which I paid for), and he said that he had fixed it.A few months later the problem started reoccurring again. Best Buy sent out repairman again who claimed there was nothing wrong with the machine. He left and the problem started reoccurring soon thereafter. I called again, and Best Buy said they couldnt do anything about it because Maytag could only work on the machine (it was now getting an F:51 error message as well). Maytag sent someone out who watched it run for 15 minutes and diagnosed that it was fine and left. I told him that the error didnt occur until the end of the cycle, but this seemed to make no difference to him (he didnt want to wait).Same thing happened again (might run five to ten loads without an error and then it pops up again), and I called Best Buy again. They sent out the Maytag repairman again (different repairman). He spent about the same amount of time as the previous Maytag repairman. His conclusion was that the machine was fine; he told us that this particular washer (the top-of-the-line for Maytag) gets out of balance frequently and that we would simply need to live with it. Like his colleague, though I told him that the error message doesnt occur until the end of the cycle, he didnt stay that long.Not long after he left, the problem started occurring again. I called Best Buy and indicated that theyve had plenty of chances to repair the machine and that I wanted a new one. They said someone would call. The response: another call to schedule a repair visit. I called them back and told them that I didnt want another repairman but rather a new machine (weve wasted hours and hours of our time giving them a chance to make the purchase right). They then had someone from the Geek Squad call, who swore that hed put his best guy on it and that he would actually work on it this time (ordered parts). He was supposed to show up this past Friday but called in sick (now rescheduled for this coming Friday). In the meantime, the machine (last night) quit working altogether. I have a pile of wet laundry and am faced with going to the laundry mat today.Im at an utter loss of words for this experience. It is truly the most frustrating consumer experience that Ive ever had. Ive watched Best Buy, Pacific Sales, and Maytag play pingpong back and forth across the table for months. I paid good money for top-of-the-line washer but have gotten bottom-of-the-line service. Surely, at this juncture, Maytag and Best Buy will finally do the right thing. I am going down to the Best Buy store this morning to visit with the store manager (and then to the laundry mat...not exactly how I wanted to spend my Sunday). If not, then next steps will be to figure out how to find representation to force the issue of the lemon law. Exasperated.

I bought a Maytag refrigerator model MBB1953XEW three weeks ago. According to its features on the Maytag website, its supposed to be quiet (QuietSeries 100 sound package). Ha ha, make me laugh. Its the noisiest refrigerator Ive ever had. The repair guy checked it out this morning. He spent about 5 minutes running some sort of test with the help of his iPad. He then told me everything was perfectly alright, the noise was normal for a Maytag, and that I was going to get used to it.Needless to say, he had a totally condescending attitude. Its the first time I ever bought a Maytag. Previously, I had a General Electric that was noisy but not as much as the new Maytag. Prior to that, I had a good old Kenmore that was perfectly alright but that I had to give away for other reasons. This time I chose Maytag because I thought it was good quality and I wanted it to be very quiet. Well, nope. Next time, for sure, it wont be a Maytag.

We purchased a Maytag Bravos Quiet Series 300 in June 09. The dryer timer has malfunctioned since shortly after purchase, it will add time near the end of the cycle, sometimes as much as an hour or more. We have had factory authorized repair firms (tried several) attempt to fix the problem both during the original warranty and extended warranty periods. They replaced the mother board twice and the moisture sensor on another occasion. All to no avail. Maytag has been worse than useless in the whole situation, and now will do nothing. It seems our only choice is to live with it, keep replacing parts, hasnt helped yet, or buy a new dryer. You can bet it will not be a Maytag!This situation is dangerous, if left unattended when the malfunction occurs the clothes and interior of the dryer get extremely hot. It is a potential fire hazard.

Every day you hear a hissing noise and water leaks in from the vents and freezes. This builds up and water leaks on the floor. You have to chip the ice out or end up slipping and falling. This happened to me - Maytag was no help. Time for a lawsuit.

Maytag WASHING MACHINE MVWC200XW - Will not clean our clothing. We have been tolerant of Maytags disregard for the people who have trusted their product and name over many years. No longer will we purchase a new Maytag or Whirlpool product. They say third time is the charm but I can not afford to take the chance. I wish them luck, they will need it.

On Thurs. Sept 25 at noon the alarms and lights started flashing on my refrigerator when I tried to get some water. I called Maytag, told them what was happening and told them to bring a motherboard when they came as nothing was working but the lights and alarms. I was told it was too close to the weekend so they would be out Mon. the 29th and I should just to get some dry ice. They came and the order said nothing about a motherboard, which is what the tech person who came also said it needed. Now they will be here on the 7th of Oct - maybe. 12 days is highly unsatisfactory for refrigerator repair. They had 4 days to see that the provider had a motherboard before the serviceman wasted a trip. Ive spent $102 on dry ice and now Im going to lose the food anyhow. I like the refrigerator but the service is really terrible so I wont be buying another Maytag appliance. The person at the call center ignored my diagnosis and it will be even worse now as over the weekend Maytag switched their call service to India!

We purchased a Maytag refrigerator in 2009. The freezer is on the bottom. In the last 3 months weve had to defrost this frost-free refrigerator. The freezer frosts and the refrigerator went into the danger level for foods. A technician said there is a tube from the freezer to the refrigerator that gets blocked with ice and your food is spoiled in no time. I wish I would have read this website before I purchased a Maytag. Hopefully, this will help someone else. I thought that Maytag was a quality name. That was the good ole days and now Im living in the good ole days defrosting a frost-free refrigerator. Beware!

We had a Maytag washer and dryer for over 32 years, the same washer and dryer. Finally our washer failed. We thought it would be a good idea to stick with Maytag. My husband purchased the Bravos XL Maytag washing machine. It is the worst washing machine ever and I regret the purchase. The washing machine doesnt clean clothes. If you use a powdered soap of any kind it leaves residue all over your clothes due to the fact it doesnt use enough water. It binds everything up. It becomes unbalanced with any larger load. Completely ties your sheets and your pants into knots. Yes literally I pull my clothes out and they are in a knot. The washer started to leak about two months ago after having it for a year-and-a-half. We couldnt locate the leak so we had to call a repairman and it cost us over $240 in parts and labor.

I purchased a Maytag dryer (MDE2400AZW) 2 years ago, but have only been using it for the last year - and fairly infrequently, as this is a dryer that my guests use. I called Home Depot where I bought the dryer (along with the washer). I thought I had purchased an extra warranty, but turns out I only had it on the washer - what was I thinking. I wish I had read these reviews before I made my purchase. My local repair man charged me $192.00 for a new heater and his time. Theres a whole 90-day warranty on the new heater!! I sure hope this one lasts more than a year otherwise Ill be buying a new dryer and it wont be Maytag.

Friends, Romans, Countrymen, At first I was skeptical and I once thought that I was the only one whose wife complained about the terrible soap stains and un-rinsed clothes. And finally my rinse and spin cycle stopped spinning and rinsing! However, after reading several reviews and complaints about the famous Bravo X He washer by Maytag and taking into consideration that there are over 650 complaints, making mine # 651. I now find I have lost all skeptical-ability and feel that we all may be comrades in this venture of purchasing the new trademark of the trade-mark Maytag. As almost all of us say our previous experience with Maytag was great. My parents had a Maytag since I was knee-high to a grasshopper and we were a family of eight. First we had the one with the rubber rollers, that was a work of mechanical genius. I even remember getting my arm caught in the rollers. Then my dad bought the spin dry model and that lasted a good 20 years. When I say the Bravo X at Sears it looked like the state of the art washer. However, and unfortunately I will have to agree with all of you. It is a piece of scrap metal and Maytag will not recall or recognize their mistake and make good on a recall or something. The least they should do is give us an old machine that does wash and spin to replace the new one that is less than 2 years old and does not work. I sure hope this letter does not fall on blind eyes. I think we may even have a collective lawsuit.Sincerely Yours;Mr. Lost All Skeptability!

Maytag Bravos XL Washer & Dryer - After a long 45-year use of our old GE W./D. that were still working fine when we decided it was finally time to upgrade. Big mistake. Nothing but dissatisfaction on every level of complaints by those who registered here before us and then some. This all was noticed almost immediately after purchase, but we lived with it trying not to believe our worse fears. That is until we both started breaking out with skin rashes. Just logged on this site after a Google search... We were shocked and disappointed in our purchase decision. We will join in a class action lawsuit if ever one is initiated... Any lawyers with one of these?

Last August I bought the Maytag Bravos XL. I have had 3 repairmen try to fix my problems with it and they cannot. The problem is, they cant fix an appliance that isnt designed correctly! Without water, one cannot wash. Dont be mislead that the huge area inside can be used for large objects like sheets and comforters. This machine is MUCH harder on my sheets and comforters than my old machine with a center agitator. I have shredded rugs, holes in sheets, black lines on clothes and a chlorine dispenser that puts spots on everything. The detergent dispenser hardware is rusted as well. Folks if this machine was an automobile, IT WOULD BE RECALLED!

We bought the Maytag Bravos Washer and Dryer set in 2013 after extensive reviews as well as the brand recognition to replace my at least 20 year old Kenmore washer/dryer. At first we were very pleased. The ability to do bulky loads was great and the high spin cycle left the clothes almost dry. In 2018 (keep in mind, just 5 years!) we started to hear a grinding sound in the washer when on rinse cycle and the dryer would randomly turn itself on! Strange but true. I called Maytag Canada and they sent someone right away. They had to replace the motherboard on both the washer and dryer as well as the drum and gears on the washer. Fortunately this was covered under warranty.Fast forward 1.5 years. Same issues with washer...technician came and could not identify the problem, although I did tell him it was the same as 1.5 years ago. I ended up recording the sound and asked them to resend technician to the house. After further diagnostics, yup...same problem. Two days went by and I received a call back advising me that the cost to repair would be over 700.00, not covered by warranty! I escalated to management, to no avail although they did offer me 15% off my next Maytag purchase! Needless to say I have ordered a brand new GE from Costco, arriving tomorrow for basically the same price to repair the Maytag. I will NEVER purchase another Maytag product and will advise anyone who cares to listen to me to do the same. Huge disappointment in the Maytag product, brand name and customer service. 10 year warranty? Not likely...stay away.

We purchased a Maytag Neptune series washer/dryer set approximately 5 years ago. This is the 2nd time in 5 years that we were told by our local repair person that the drum of the dryer got bent out of shape. This is from normal use and due to a bad design on their end. Maytag refuses to foot the bill (about $350-$400) as it is out of warranty.

We inherited this Maytag (Model MGR7662WW) when we bought our house this year. I love this unit. It cooks accurately, its easy to clean and its just rock solid in its performance. I never worry that the cook times are going to be off either. The oven racks are solid and the overall look is nice. Our friends and family love the center grill as much as we do. If I need to pull something off the burner I dont worry that Ill scratch the stove top with this feature. The oven heat is also pretty contained. Our old oven radiated lots of heat through the top. This one doesnt and thats a huge plus. The only reason Im not giving it 5 stars is that the grills are cracking (not the center one). However, I have no way of knowing if the original buyer damaged them or if its a defect in materials. They still work fine but I will need to replace them at some point. Given the cost of replacing them Ill wait as long as I can.

I had the exact same experience as the Tampa person with my Maytag dishwasher (Model: MDBTT60AWW). It was not cleaning the dishes, even when I thoroughly rinsed them. Plus, it started leaking midway through the cycle. Since the warranty was expired, I purchased an extended warranty in July 2012 for $296 (yes, in hindsight, I should have just bought a new appliance, not Maytag). I had 3 visits from 2 different technicians, both telling me the dishwasher did not leak. One telling me I was using the wrong kind of detergent and thats why dishes werent getting cleaned. The other telling me that there were too much suds and that could cause it to leak. So, I should pour a tablespoon of cooking oil (yes, cooking oil) in the dishwasher when it starts leaking and that will cut down the suds. I dont think so!Then, I found out a couple of weeks ago that this model was under a recall since 2010, not related to the leak at all. Yet, Maytag still sold me the extended warranty (wheres the ethics of that?). I requested a pro-rated refund of the balance on the warranty - and wouldnt you know that with the technicians service calls, the amount of time used on the warranty (6 months) plus an admin fee - I have used $296.48 of the warranty amount. It is almost to the exact penny of what I originally paid, so I will not be receiving any refund. They are only giving me a debit card of $150 or $250 once I buy a new Maytag to replace the recalled model. I do not want to continue down this frustrating path known as Maytag appliances.

We purchased this model from Home Depot in February 2011. In July 2011, I found it full of water and dirty dishes after running a wash cycle. It was completely dead like it wasnt getting any power. I checked the fuses, etc. - nothing was wrong that I could find with the power supply. I called for a service tech that day and they sent someone out to check it. It was the control panel. They shipped me a new control panel and the tech came back to replace it under warranty. It worked great until July 2013. Again, it is full of water and dirty dishes, wont turn on and has no lights on the front panel. I called Maytag to get a service tech. The warranty is expired of course. They offered to sell me a replacement dishwasher at a discount for $409, Model # MDB7749SBW. Or I can buy an additional 1 year of warranty for $269. I also could buy a control board for about $150 online. None of these options is attractive right now, but hopefully if I get the new model, it will not have any issues... I wish they would just tell me it was a crap unit instead of giving me the option to either get a new one or pay for a useless warranty. I am fed up with this dishwasher. 2 control boards in 2 1/2 years is unacceptable and indicative of a defective unit or design. After reading the reviews here it appears to be a defective design.

I had a Maytag dishwasher that I purchased around 2005. I had no issues with it at all. Then, I got a notice that it was being recalled due to a fire hazard. My options were to either get a repairman to come out and fix it, or get a credit towards a purchase of a new dishwasher. I chose the second option. Even after getting a credit, the purchase cost was way more than my original dishwasher. I purchased the new dishwasher in June of 2010. Last spring (May 2012), I noticed a gap in my hardwood floors around the sink. A flooring rep looked around and said he would bet that theres a leak either at the sink or the dishwasher. I took off the front kick-plate to the dishwasher and discovered a wet spot. I monitored that area and discovered the leak coming from under the dishwasher (around the float switch). It wouldnt leak all the time, but every now and then, it would leak half to a full cup of water. I had the hardwood floor fixed (cost $350). At the same time, I schedule a service repair through Maytag. They sent a rep from a local repair company (Convenient Appliance Service, Inc.). The service rep couldnt identify the cause of the leak but said it was more than likely the seal around the door. So, I paid another $160 to get the repair done. I monitored the leak for a week and had no problems, so I put the kick-plate back on. In September 2012, I noticed a wet spot in front of the dishwasher. I took off the kick-plate and discovered that the dishwasher was leaking again. This time the leak was worse. It would leak 1 to 2 cups of water during a wash cycle. I called the repair company and they came out free of charge to take a look at it. The service rep said the float switch had gunk build up in it. He cleaned it out and said that should fix the problem. I monitored the area for 2 weeks and everything seemed to be fine. Last week (March 2013), I noticed some gaps in the hardwood flooring around the sink and dishwasher. I pulled off the kick-plate and discovered a wet spot. I ran the dishwasher and discovered that it leaked a ton of water (over 4 cups). I contacted the repair company that came out last time, and they said they would have to charge me $100 plus to come out and take a look at the problem. The rep recommended contacting Maytag. I contacted Maytag and they said I would either have to pay $129 for a service call (not including cost for parts), or $269 to get covered under their Repair Plus 1 program (everythings covered and it adds 1 year of warranty my dishwasher). I asked at what point Maytag would replace a dishwasher. The rep said when it is deemed unfixable. Other than that, they just keep coming out if I have issues. Part of me thought I need to cut my losses and just rip out the dishwasher and get a new one (cost somewhere around $700). But I went with the Repair Plus 1 program in hopes that they can resolve the issue. But Im definitely going to have to get the hardwoods ripped out again. It looks worse than before. It’s probably going to run another $500.

I am happy with this dishwasher. I had a GE that had a lot of problems. I insisted on getting Maytag and I have been happy ever since. It controls the time, temperature, and is easy to operate. I would like a bigger dishwasher because of my family size. This dish is okay for a family of 4. It matches my furniture. It blends in. No complaints. The digital pad is convenient but it has been fixed a few times. I had a few technicians who did not know how to fix. It was not the dishwasher, it was the technicians.

Maytag Centennial HE Washer - Worse machine ever. Takes over an hour for a load of clothes, never clean. Had only for 18 months now, it wont advance past wash cycle.

I bought my maytag stove model MGR7662WS on January 30, 2011 and have had it serviced 3 times... same problem. I set oven to 350 degrees, put food in oven and later check on food only to find the temperature reads 350 but the oven is cold. Food is not cooked and it smells like gas. I turn it off and turn it back on and it does not turn on most of the time. Service guy keeps replacing parts and says he will replace the same part he just replaced last week. He says sometimes the part comes out defective. I think the stove is defective and I have thrown away so much food because it does not finish cooking and smells like gas. Its so frustrating because my Thanksgiving was ruined two years in a row due to turkey not cooking.

I paid $958 + tax for a Maytag Bravos washing machine in August 2008. I live by myself, so the machine is not overused. Nevertheless, it began to sound like a jet airplane during the spin cycle. And then in May of 2012, it failed with error code F51, catastrophic failure. The machine was not even four years old. I called a certified Maytag repairman. In less than 5 minutes, he told me the cost to repair would be about $900, and then he charged $115 for the service call! A call to Maytag resulted in Im sorry, there is nothing we can do.

I called Sears to have a simple repair done to my Neptune washer and received a quote for $800.00++. They gave us a coupon to get a new washer at Sears and we did. Last week my dryer broke and I looked the repair up on Youtube. It looked real simple. A quote for $270 was given to us. Again a coupon if we wanted to buy new. It seems to me Sears jacks the price up on its parts and labor in order to push the customer to buy new. So far its worked for them and Im sure everyone else as well. Its not going to work out for Sears this time. Im no longer doing business with them and I will do the repair myself. I still got stuck with the service call but that will end as well going forward because I know now what the game is. Shame on you Sears. Double thumbs down for my Maytag Neptune washer and dryers.

I have had this refrigerator for a few years and never have had a problem. It keeps food uniformly cold, and is frost free. While appearance is attractive, it doesnt look like a $3,000 refrigerator. However, black pebbled-surface exterior is easy to clean and scratch-resistant. Plastic and glass interior fittings also have held up very well. I originally thought it would be too small because I was buying it to fit a certain space in the kitchen. But it has turned out to be just the right size because there is no wasted space inside. I bought this at Home Depot on sale for about $400.00 and it has turned out to be an excellent buy. Delivery was on time, efficient, and people were polite and helpful. Refrigerator was ready to be used about 15 minutes after delivery arrived. I have found Maytag appliances to be extremely reliable and made to last. They have never disappointed me. I will continue to buy them. I highly recommend it.

It’s the worst washer I have ever encountered! I never have clothes that smell clean. The water seems to never completely spin out, the spin cycle is terrible!!! My whole house shakes when it’s spinning and the noise coming from it is so loud. The time on it is never correct; it will say there is 9 minutes left and then just go to 1 and quit! My clothes have never looked clean with this machine. And yes, I use very good detergents and everything else to try to help with no luck! The dryer just takes forever to dry anything. Needless to say, I will NEVER purchase another Maytag again!

Bravos MCT - I researched online and bought the highest rated machine that had the features I wanted. I like the top loading and the less water used. It cleans well but I would like more control like water temperature for example. I have had this washer about a year. I also want quiet but did not get it in this washer. That is tough cause you dont know until you have it! I think that it is hard to buy big appliances and be happy with them at my age because at 70 years old you remember when a washing machine was built to last a lifetime! Now they last maybe five years and they cost as much or more! I am not interested in lots of the bells and whistles. I just want a washer that will last and does its job. Mine has a glass door in the top so you can watch your wash (I guess..). Well, who wants to stand around and watch your wash...get a life!!! Also, it fogs up right away so you couldnt see it if you wanted to. It all seems pretty silly to me but I guess that is the way the world works today. So I go with it and I watch my wash.

My Daughter got me a Maytag oven with the AquaLift technology and is a piece of Junk. Half the time the Water is still there when the cycle is over. The water has made it between the front glass pieces and the finish on the top of the stove looks horrible, it just looks dirty. The knobs are cheap and the fake chrome finish is flaking off. Unfortunately Im stuck with it because I cant afford a new one... this was a gift to me because Im disabled and it was to make my life easier.

Maytag Centurian is a terrible product. I dont think the designers of this model have ever washed and dried a load of clothes. Washer problems: The lid (top loading) locks so user unable to determine if the correct amount of detergent is being used. There is an unlock button, but it takes quite a long time to unlock (maybe 15 seconds), then an even longer time (seems like a minute or 2 to restart). The machine is LOUD and at one point in the cycle BANGS. I actually returned the first as defective, but when the 2nd machine made the same noise, I was told, no, thats the way it is. It seems to take much longer to wash a load than my previous machine. The Power Wash tears my clothes. Even the regular wash puts holes in my thin tee shirts after a few washes. Really had to get spots out. I almost have to hand wash to get the spots out BEFORE putting in the machine. Dryer Problems: Takes 70 minutes or more to dry a normal load with a couple of towels. The cover to the lint catcher doesnt seem to be properly sealed. Lint particles get all over the top of my dryer. I bought this Washer/Dryer combo last year. Im annoyed every time I do laundry.

It meets all of my needs and expectations. Its quiet looks nice and does a very good job of cleaning dishes.

Unbeknownst to us, our Maytag Refrigerators (MFD2561KES) ice maker developed a problem with the fill hose which connects to the back of the refrigerator, causing it to pop off. The hose had been leaking water onto our wood floor causing all of the boards under the refrigerator and 6 feet in front to buckle. I cannot see why Maytag did not use a compression fitting instead of using a squeeze type hose clamp. Plus the ice maker has left a large sheet inside the freezer on the bottom. I use the ice maker daily to fill my cooler for work.We also have a Maytag Dishwasher which has a push button panel in front which has decided to give out as well. Not to mention our Maytag Double Oven which has never been able to close properly since we have had it. (The service man said that there is nothing wrong with it). We bought our house 7 years ago and my wife wanted nothing but Maytag because of our experience in the past. I gave up buying american automobiles years ago and I guess the same will happen when I replace these appliances (after I finish paying for my new floor).

I have had 2 Maytag washers in 37 yrs and loved their products, however I purchased a Maytag quiet 300 in 2/09 and it is the worse Maytag product on the market. The frame around the bleach dispenser has rusted out and I have called for the 3rd time in 5 years to have it repaired. To my dismay it will cost 300.00 to fix because the bearings have to be replaced. I will now have to purchase a new washer. The days of the Maytag man are long gone. By the way the Maytag dryer has been serviced twice. I thank God everyday for that extended warranty I bought, but now it has now expired.

We purchased our Maytag Bravos washer/dryer in January of 2012. In October of 2013, I noticed that the lid would not close properly. In examining the lid, we discovered that the screws were in tact but the information panel on the inside of the lid had come unglued causing the lid to be obstructed from closing properly. After calling Maytag we were told that they make a quality product and, in what I consider to be a condescending reply, could not help us. Replacement of the lid with the service call would cost almost the cost of this expensive washer. So disappointed in what we thought was a wise purchase!

Hate my Maytag Centennial Commercial Technology washer. It takes well over an hour per load. Clothes come out very wrinkled, and my knits get holes very quickly. I would not recommend this machine to anyone. In fact, I warn people against it as I have been frustrated every single time Ive used it. Model # W10420382A.

Dryer doesn’t dry any size load in one cycle regardless of settings. Mysteriously, it triggers a message to check the lint filter and line when running a small load with nothing blocking the venting system. It never happens on large loads which would block more of the air flow. You could get a comparably sized dryer for much less. This not the premium product that you pay for.

Im currently standing in front of my washing machine waiting for the 13-minute drain and spin cycle to finish because once again my load didnt drain and finish right. Except it has already been 40 minutes and it claims there is still 9 more left as it continues to sit there doing nothing while it hasnt even started spinning yet. It Sat on 13 minutes while sensing for over 5 minutes, then 12 for 10 minutes while doing nothing, then it changed to 11 minutes and made some weird noises but didnt actually do anything for 15 minutes, and now the timer randomly changed from 11 to 9 without any noises or movement happening and now continues to sit here.I stupidly thought I could spin my clothes real quick to throw them in the dryer before bed and now I stand here extremely tired and very irritated. I also have no doubt some of the clothes will have holes in them when theyre done because they always do, my family looks like were homeless and ratty half the time we get dressed now. Also it never deep cleans thoroughly even on the toughest settings, I swear our socks can be washed 3 times in a row after being soaked all day and still come out crusty or a lot of times the armpits of shirts will still smell or be ultra stained with deodorant marks still.This technology is almost too advanced and everything is decided by sensor, regardless of the registered functions on the buttons it will still do what it wants as the sensors see fit and run when they decide everything is perfect and ready, including taking 10 minutes just to unlock the lid when you pause a load cuase a small child may drown in the foot of water or a person may have their life completely altered by getting a little bit wet if the machine isnt completely drained and in pristine condition before you open the door. This machine is terrible. This company is terrible. And worst of all they drain your wallet for these horrible contraptions. I wish I could rate this 0 stars.

I bought a refrig from Home Depot on 10-16-2012 two years ago and it doesnt work, but they only put one year warranty on. So had to go out and buy another. My complaint a refrig should last more than two years but they were going to send repairman out on my expense and more than likely would of cost me the price of a new one.

It’s a front loader, very quiet, and uses less water. The clothes come out clean and less wrinkled if you take advantage of the settings. l like the extra rinse and the drawer underneath. The capacity is able to accommodate enough clothes so I only need to do a load of darks and a load of whites each week.

I bought my Maytag dishwasher on September 4, 2013. In August 2014 the control panel went out. (Sound familiar?) The dishwasher was still under warranty, so I called Maytag. It took 3 tries to find a repair person who would come out on my schedule. (Im a teacher and cant take time off.) They installed the new control panel, and it working. I tried to submit a review on Maytags website, but my review was denied. I guess they didnt want to hear the truth.

Not only did I buy a Maytag washer for the brand name and trusted longevity, but because they were always a good product in the past. When my Maytag EZ-Epic washer drum failed after only owning it for two years, there was no effort made by any associate to cover this under any sort of warranty at all. To replace this part, I was quoted so much money that I could go out and buy a brand new one for the cost of the repair for this faulty part. I am extremely dissatisfied with the way I was treated because the so called product was out of warranty and I will never buy a Maytag product again. Shame on Maytag for ever selling off to such a fraudster of a company.

Purchased Maytag MDBH979AWW serial #FY4202009 from Lowes October 30, 2009. Control panel went out after warranty, and we replaced it. It quit working again in May 2012, and we replace the control panel, and then in November 2013 it quit and we replaced the control panel along with a new door latch just to be sure on December 4, 2013. The dishwasher quit working mid-cycle a couple of weeks ago only 9.5 months since we replaced the last control panel. Im fairly certain it is the control panel again. We have paid more to replace control panels for this dishwasher than we paid for the original appliance. There should be a recall and compensation on this issue. Very disappointed that Maytag and Whirlpool do not resolve this issue. We will be buying a different dishwasher, and it will not be Maytag or Whirlpool.

We bought a Maytag washer and dryer in April 2012. A few weeks ago the washer while it was spinning out, it sounded like it was metal on metal. Sears came out and said the transmission and the tub had to be replaced and the tub was created to the transmission. My husband and the only ones living in home and I sort my clothes, so I dont have big loads. I contacted Maytag, their answer was its out of warranty so we are not going to do anything for you. Anyone who buys a Maytag Washer, watch out what youre getting.

Its unfortunate that Maytag expects their products to be so short lived, they wont produce parts for their appliances after 7 years. They just told me they are only required by law to make parts for their products for 7 years so thats what they do. So unfortunately, if your microwave outlives its handle, youre going to have to replace the entire appliance which will cost me almost $500. I will never buy another Maytag or Whirlpool products because of this.

I have had this washer just a little over a year and the sensor panel went out... For $600.00 it should not break right after the warranty goes out. Buyer Beware.

Maytag fridge is a overpriced, ticking repair bomb. The fridge had issues with the compressor, control board (motherboard) and relay switch within a 12-month period. Customer service is weak in troubleshooting techniques and try to send the file over to a repairman. The repairman will show up at $80/hr + other fees and parts costing you approx $500, and still uncertainty that this fridge can breakdown at any time. Final advice: DONT BUY.

I had my dishwasher for several years. Never had an issue with it. Cleans well and is very quiet which is exactly what I needed. A quiet and effective dishwasher is hard to find. The price was about six hundred dollars. I pursuit at Lowe’s. It was on sale along with a military discount.

I purchased a Maytag Bravos XL at the end of June 2013 because my washer of 14 years finally quit. On the 2nd load of laundry I ran, the machine began making a terrible grinding noise. It sounds as if I am washing a load of rocks while its on the wash cycle. I immediately called the local store I purchased it from and they sent a technician out to look at the machine. He couldnt figure out why it was making this noise, so he called Maytags techs for assistance. They had him run a battery of tests and they finally determined they needed to replace the motor. Are you kidding me? On a brand new machine?! Now Im thinking I have a lemon for sure. They replaced the motor and the machine continues to make the same noise. Ive called Maytags Customer Service to let them know about the garbage theyre producing and all I got was attitude. The warranty only covers parts and does not replace machines, so Im stuck in the song and dance of lets try to figure this out and see how they can make this piece of junk work. I then asked to speak to a manager. She offered me a 6 month extended warranty for free. I guess thats a big sign that Im going to need it since what they are producing is garbage. Whatever happened to customer satisfaction? Its now just the too bad attitude. Now, I feel like Im being held hostage by my machine because I have to take time off of work for appointments with service technicians. Wheres Maytags compensation for my time and the hassle of having to deal with this? I paid $1000 for something and I guess its too much to ask for it to actually work. I am all for buying American (the machine had a sticker, proudly made in Ohio) but if this is the quality of work that they are producing they should be embarrassed to work for this company. I will never buy a Maytag again and am making it my mission to warn others of my expensive mistake!

I have owned my Maytag washer for approximately five years. Ive always used the recommended detergent and religiously used the tabs to clean the machine when it was required. I have never abused the machine by overloading it, using too much detergent, etc. It is now coming up with an LF code. There is no one in this area who does repairs and if I do find someone Im sure theyll want some exorbitant amount to come all the way out to the boonies to give an estimate and the repairs Im sure will be hefty. I take very good care of all my appliances and expected this machine to last much longer.

Purchased my microwave in 2005 and seldom used it. However in the last few months, the halogen light which lights up the range surface has been flickering. When I asked an electrician doing other work around my house to repair it, he discovered that the halogen light is attached with a dual pin socket which is plastic. When the halogen light gets overheated (and halogen produces alight of heat) it melts the plastic. It has already melted some of the plastic socket. When it fails to operate, I will have to repair the light socket which will be very expensive or buy a new microwave. This microwave cost $800 or more because it offered convection cooking which I have seldom used.This is what is presumed quality appliance? Plus I added the cost of an extended warranty.

I live alone and bought this unit for long life. After a few short not-used-much years, my washer sounded like a 747 was landing in my laundry room. I am a maintenance person, so I did a bit of troubleshooting and narrowed it down to the bearings installed in plastic on the outer tub that failed. My cost was $600.00 to $750.00, parts alone. It still worked, just very noisy on high spin.I emailed Maytag (now Whirlpool) and was phoned by Lee Ann. I told her I had all Maytag appliances in my home and was laid off and that if after the use this washer has had and it will cost this much if I do the work, I was not impressed with this company. She apologized and told me she will issue me an extended warranty for $299.00 that will cover it. I told her that without a job, I cannot make a decision so fast. She gave me the next business day to decide. I concluded it was cheaper than the part, so I called her back. I was scheduled for a repair, and the man opened the front and looked at it and said it was an outer tub bearing. He went to his laptop in his truck and returned to tell me that they would not authorize that expense and that all they would authorize was $350.00. He put the front of the washer on, then as if he forgot something, took it back off and reached way in the back and did something. Then, he reinstalled the front. I was livid! They charged me $299.00 for a warranty and would not repair! So I called back and was hung up on. Next, I called my credit card and disputed the charge. I tried to use the washer, and it made funny sounds and then filled up my home with smoke and stopped working. I called Maytag again, and he denied the repairman would tell me how much they would authorize to repair it and told me good news that they would issue a $174.00 check. I gave $299.00, and a few days later, they give me $174.00? This is why Whirlpool is destined to fail. I will never buy again, and I will wash in my laundry tub first! This is exactly why imports will rule! So Whirlpool, you got me for the last time!

This washer had good reviews when we bought it, but now today the agitator is not working. I see there are now 100s of bad reviews of this machine most around the same 1 1/2 year mark. How unacceptable to have a large appliance like this break after such a short time. Ive called Maytag to see if there was a recall and there is not. They offered the extended warranty to me for $325 that would cover all parts and labor. Ridiculous.

2 major repairs in 8 years, ridiculous! We purchased a washer and electric dryer pair in Feb. 2012, had a repair for the control board (CPU) 4+ years under extended warranty, had another in 2018 for the same thing. I was told power surges could cause it, however I have a WHOLE HOUSE SURGE SUPPRESSOR ON THE INCOMING 200 AMP SERVICE AND KNOW THATS NOT THE PROBLEM!!! Had the same CPU go out again in Nov. 2020 so, rather than pay $370 for the part plus labor, we bought a top loading GE with an extended warranty and factory 10 years on the motor. We will never buy another Maytag product again. We were told that we shouldnt expect to get more than 6-7 years from a washer now, ridiculous. Manufacturers are outsourcing electronic boards overseas to maximize profit and could care less about quality control!!! Junk!!!

Have 2 fridges (one regular and the other is a side-by-side, both were bought in 2006 at Future Shop. The small one is not freezing and the side-by-side ($2,200) is busted too (compressor wont start....). How can Maytag say that their product are reliable on TV??? A Fridges compressor should last at least 15 years !! Maytag, you should at least have the decency to pay for the compressor!

This is the noisiest washing machine ever manufactured - cannot do laundry at night or no one sleeps, during the evening it overpowers the television. Dark washes are a nightmare as there is a white smear (soap scum?) on everything (guess you don’t see it on whites) - extra rinse does not help. What happened to this “reliable company”???

I purchased our Maytag Dishwasher in 2014 (Model # MDB77495B) and after a little over a year, of course after the warranty had expired the panel started to act up. I did get it repaired costing over $300 for parts and service thinking all is well. The repairman that came out had to come out twice once to look at and then again to fix after the part came in. We had a conversation and he said that was common with this brand, the steam sometimes affects the panel. I spoke with Maytag about getting an extended warranty but after looking at the cost passed on it. Well now the panel is acting up again. If Maytag thinks I am going to have another repairman come out well think again. I will see how much the part cost and do it myself if it cheap enough, if not I guess Ill be back to washing dishes by hand for awhile. I bought this brand feeling that it was American made and the cost was on the expensive side that it would last. I am disappointed that this has happened again. For the money spent it should last at least 10 years. My old dishwasher that was given to me used lasted over 15 years with not one problem. Its a shame we cannot get good working appliances as we did back in the day.

We have a Maytag Gemini Double Oven Range Model MGR6775ADW. This is a gas range and it was purchased in 2006. This past Saturday afternoon after cleaning the dishes, the igniters on the range starting ticking on their own. I checked to make sure the knobs were not on and they werent. The ticking finally stopped after about 2 minutes. After the ticking stopped, we planned on going out for a walk. Fortunately we didnt. In about 10 minutes after the igniters quit ticking, the range burst into flames. Flames were in the top oven and shooting out the vent holes and the holes where the knobs are located. Coal black smoke was also pouring out of the vents. I quickly pulled the stove away from the wall to prevent the cabinets from starting on fire and I pulled the plug to shut off electricity from the stove. The flames subsided shortly after pulling the plug. The kitchen and house smelled of burning wire insulation and plastic. After doing some research on the internet, I found out that many other people have had the same problem. I reported this to Maytag Customer Service and they wanted to send a repair technician to fix it. I told them I didnt want it fixed but wanted it out of my house. I told them I didnt trust the range since some people reported they had it fixed and the fire occurred again. I wouldnt be able to sleep or go out anywhere knowing that the kitchen range could erupt into flames at any time. The factory authorized repair technician, from A&E, did come to inspect the damage and to report back to Maytag on his findings. He admitted that he wouldnt even trust the range in his house. After paying $1300 for this range and only getting 6 yrs. of use, I feel that we deserve some restitution from Maytag on this badly designed and dangerous piece of equipment they have been selling. Do not buy the Maytag Gemini range. This is a bad and dangerous product.

We loved the Maytag dishwasher when we first bought it. After about 5 years it started leaking. Had rubber gasket replace, only held up 2 years. This was the only problem.

My Maytag dishwasher MDB7749SAM is not quite 5 years old. At the end of December 2016 a bubble appeared on my vinyl floor. The plumber could not find any broken pipes or reason for any moisture to have gotten under the flooring. A flooring company did not know what was causing the bubble, moisture or the vinyl glue had failed. The floor got worse and worse, more bubbles.Called the flooring company again. Raised the register cover and could see all the moisture under the vinyl and underlayment. Plumber discovered the dishwasher fill valve had failed but because there was so much insulation on the kick plate, at the bottom of the dishwasher, it forced the water, which was in a pan under the dishwasher, to push the water to the back by the wall and under the flooring. Plumber said, the insulation acted like a dam to keep the water from showing in the front of the dishwasher. The first and subsequent bubbles, in vinyl were 3 feet away from the dishwasher. No way to tell the dishwasher had the problem. Has anyone experienced this problem? If not, take care to remove the kickplate and check your dishwasher for water problems.

I just bought this piece of junk... Like everyone else I guess I didnt do enough research! I have had this washer for less than 3 weeks and just like everyone else I am so disappointed in how it tries to wash without water! I too have tried different settings. I had to wash a load 3 times... pausing it while trying to get the rest of the items wet. Its ridiculous... of course now to try and see if I can return it! Yah right... Home Depot does not have a good return policy and Im afraid I will be out 800+ with this washer. This is ridiculous! It really is.

I purchased the microwave less than two years ago. I noticed the display panel would not always work a few months ago. This is part of the control panel that shows time, etc. Called Maytag just now & they told me that the control panel is starting to fail. I could purchase a one year extended warranty for $289!!!Are you kidding me??? The part alone would be around $160. What has happened to Maytag? I thought they had a good name. :( Very disappointed.

This Maytag bravo washing machine is the worst ever machine I have owned. I bought it new, and shortly after the 1 year warranty expired, I started having problems with it. I had a repairman come out. All he did was take out the trouble shooting guide, press a code, and wait. The machine told him that each function worked. Even though it did not work properly. He hid the trouble shooting guide inside the machine, so I cannot get to it. Now I have so many problems with this machine, that it takes me all day to do 1 load. This thing makes noises that I have never heard from a washing machine in my life. I would never buy another Maytag product, nor do I recommend anyone else to buy one.

I bought a Maytag dishwasher (model #MDBH979AWS3) from Home Depot on July 2010 and had it installed. After 2 weeks, I found water leaking into the basement. The installer said rubber gasket in water line de-laminated and caused leak under the dishwasher and flooded the floor to basement. Product defect and water damage covered by Maytag insurance. Now Feb 2012, about 1 1/2 years after buying, the touch panel controls dont work. I called Maytag regarding any control panel recall and they said no and its out of warranty. The advice given was that they can send out a serviceman for $269 to fix with parts, labor and one year warranty. It seems like planned obsolescence. Dont buy a Maytag.

Maytag Washer Model#MVWC465HW2, just purchased it 1/30/2019, leaves white stains on dark colored clothes. I use liquid soap. I don’t use softener nor bleach. I use OxiClean on my whites and sheet softener in the dryer. Someone please out there help, I can’t return it, it’s past 30 days. I have extended warranty but they can’t help. It’s not broken. I hear a lot of bad reviews/complaints, but no answer if it’s been solved or how to solve it. Please someone help???

We purchased a high capacity washer (MVWB835DW), along with the matching dryer, two years ago from Lowes. This review is not about Lowes. They did the best they could to make things right. The review is about the Maytag washer (made and serviced by WhirIpool). It has been nothing short of a debacle. The first two washers did not work and had to be replaced. The third and current washer has been repaired three times, including the drum and motor. We have been without the use of the washer for over a week each time while waiting for parts and Whirlpool to approve the repair. The washer is not high capacity as advertised. Filling the drum even half way results in the washer stopping mid cycle whereupon we have to adjust the contents back into balance. In addition, the machine leaves a lint residue on dark clothing that has to be wiped off by hand. We have asked Maytag/Whirlpool to replace the machine but they say it has to fail for the same issue four times in order to qualify for replacement. We are done and will purchase another washer from a different manufacturer. It’s easy to understand why Samsung and LG have become such a dominate force in the laundry sector. Whirlpool/Maytag does not care about you or the problems with their product. Buyer beware!

I bought this machine about a yr ago. My clothes come out so dirty white spots all over my clothes. Now my bills are higher. Because I cannot afford another washing machine I have to bring them to the laundromat. I saved my money a long time to buy a washer and now I am without one and still paying for this piece of tin that does not work... If I ever get a chance to buy another one it will not be a Maytag. Trust me never never never again!!!!!!!!

I recently purchased a Maytag centennial washer and dryer from my local Home Depot. I set up a delivery date of 2/9/12. I was contacted on 2/6/12 by a Maytag staff telling me that my washer and dryer were on back-order until 2/29/12. This is unacceptable to me. Why does your company not tell its retailers that some items may be back ordered? I would have accepted this if told when I scheduled my original delivery, but being told days later and after taking the day off from work, is poor customer service to me. I am giving very serious consideration to voiding this order and finding a new company to deal with. I do not have the confidence that future issues will be shared or dealt with in a timely manner.

I purchased a Maytag Bravos washer and dryer combo 2.5 years ago. Six months in, I noticed that the washer would always stop halfway through the cycle. We had a repairman come out because it was under warranty and he said it just had to be reset. I then started to become weary of the product. The washer, that is larger than most, is still a problem today. The dryer, the last couple of months, has not dried clothes completely. Today the dryer just stopped. Maytag will rip you off when called for service because the warranty is expired. I have owned old dryers for several years and I am so disappointed with the Maytag product that I will make sure that anyone I know thinking about purchasing a Maytag will buy another brand. The worst washer and dryer I have ever owned.

I bought a Maytag Neptune top load washer in 2002. It worked fine (with the exception of smelly clothes) until October 2011. Since then I tried replacing two new clutch assemblies, a new outer tub and bearings. What we were just told this week: it needs a new spinner. Finally throwing in the towel and taking the $500 credit from Sears and buying a new washer. And I can guarantee I will never buy another Maytag product again!

We purchased a dishwasher (Maytag) two or three years ago. We have had nothing but trouble with it. The welds on the upper rack broke. The wheels on the low rack keep falling off. Water leak happened recently. The start button broke. My wife and I decided to just get a new one rather than keep sinking maintenance costs which are going to keep adding up.

This machine is the worst! I purchased this Maytag washer 2 years ago and the machine leaks from the left side bottom. I called Maytag and they said I need one of the techs out to check the machine and the cost was going to be $115 so I agreed even though was not too happy that there is no guarantee after 2 years. The service tech arrived. He could not move the machine himself and was a little angry so my wife called a neighbor to give the tech a hand after looking at the machine. He called if office to help him diagnose the unit and said the drum seal was bad and it would cost $315.00 so my wife agreed but at the end of the transaction my wife asked the technician, Is it guaranteed that this would fix it? He replied there is no guarantee but we still have to pay to try... What kind of diagnostic is this, Im very unhappy with this company. 1st the machine sucks after 2 years to start leaking and 2nd their service dept. sucks also... stay away from Maytag.

Worse washer ever, clothes are dirty and smelly. Customer Service is even worse. After a normal cycle clothes come out half wet, never enough water in the machine. Everything gets washed on bulky and there is soap residue on everything. Have taken clothes to the laundromat on several occasions just to get them clean. I cant wait to get rid of this piece of crap!!! Never ever buying Maytag again!! Warning to everyone... DO NOT BUY THIS MACHINE!! And with the extended warranty, they still dont cover it. :(

Five years ago made a major investment on new techno with this washer/dryer. This is an updated review. Since the beginning the washer causes awful water hammer. Tried using arrestors, they dont work. Clothes are stretched out. You need to bundle each piece of laundry! The wash takes forever. Top loader has lid lock, very inconvenient - Dryer is OK but needs extra drying time. Would not buy this washer...

I have always stored clean dishtowels and oven mitts in the storage drawer of my ovens (for over 50 years). I bought a new Maytag (2 days old) and was cooking in the oven tonight. I opened the drawer to get a mitt and it was on fire!! I am shocked. How dangerous is that! I looked over the manual and there is nothing that says towels cannot be stored in the drawer. It was literally on fire. I emptied the contents of the drawer into the sink. Has anyone else had this problem?

My Maytag top loading washer, 4 years old, stopped working in the middle of a wash cycle. Registered Maytag repairman did a diagnosis and finally identified the problem with the control board. The cost of the control board would have cost almost as much as the original wash machine especially since I had to pay for the current service call and labor (to diagnose the problem). After having read a number of other reviews from dissatisfied customers, I will not buy another Maytag product. I was under the impression that Maytag produced a superior appliance but was disappointed by this experience.

When our ice maker (Model # MF12269VEM10) stopped working, we contacted Maytag, only to be told that the 1-year warranty had expired. So we had no recourse but to contract a repairman. He replaced the valve (and in the process, because of Maytags decision to use plastic tabs instead of screws, the tabs for the filter housing broke off in his attempt to reach the rear of refrigerator where the valve went and we had to pay to have the housing replaced, also). The new valve did NOT fix the problem. Water continued to run out of the water dispenser after you removed your glass. We re-contacted the repairman who returned and proclaimed that there was air in the lines and it should work itself out over the next several days. Yet that night, I noticed drops of water running down the control center and filling the drip tray. I placed a towel on the floor and emptied the drip tray several times that night, before turning off the ice maker completely the next day.Unhappy with the original repairman, we contacted another who came out and discovered that the new valve was leaking from the top. That is when the filter housing broke and we had to use duct tape to hold it in place while the new repairman ordered a replacement. He tightened the valve and cycled the ice maker several times only to discover that the water overflow switch on the ice maker wasnt working, thus water was overflowing into the ice maker container. He turned down the water pressure to the refrigerator, and we tested it again. All seemed to be well until the next day when no ice was released from the ice dispenser. When I removed the ice storage bin, I found everything frozen from water overflow. I turned off the ice maker entirely and contacted the repairman, who ordered a new ice maker, which took about a week.After the new ice maker was installed, along with the new filter housing, the repairman cycled the unit several times before leaving. Yet by the next day, the ice in the storage bin was frozen in place again (I have pictures), and we contacted the repairman who ordered yet another ice maker. It took yet another week for the part to come in. After it was replaced, I monitored the ice container each time I heard ice drop into it. The 1st time there were a few drops of water in the bottom of the ice maker. The 2nd time, there was a 1/4 cup of water in the bottom. I immediately contacted the repairman to let him know and turned off the ice maker yet again.I find it hard to believe that a new valve, fresh from the package, and 2 (TWO) ice makers, fresh from the box, were all faulty. The repairs started on February 25th 2015. It is now March 21st and the ice maker is still not repaired. The 2nd repairman is doing his own research into the problem (for which we applaud him!) and now we ask you for your feedback as to the problem and how it can be solved.

We bought our Maytag Neptune washer in 2005. We chose Maytag because of their reputation, their headquarters in Michigan, and because looking at the machines in the store, they seemed to be well built. Were we ever wrong! You would think paying $1000 for a machine would get you a product that lasts longer than 8 years! Our other washer (a Whirlpool) lasted 20 years and was still working. Im now consistently getting a 3e error code. In searching online, I found that this is a pretty universal problem and thought maybe Maytag had a recall on it. What a waste of valuable time. I did find out the machine was actually a Samsung. This seems like fraud. If I wanted a Samsung, thats what I would have purchased! Contacting Maytag Customer Service was like Land of the Stupid. After getting the runaround and being sent to a phone number and website that only covered Samsung I called Maytag again. I was put in contact with another person who could supposedly help me with the recall. Even though I told him what the problem was, he gave me the robot response about sending the GFCI plugin and told me, That should make your washer safe to operate. Seriously??? I replied, This wont fix the problem because THE WASHER DOESNT WORK and we got the recall part long ago. He then wanted to schedule a repair appointment. Not doing that, considering how stupid the Maytag reps I had talked to so far had been. Putting the hubby on the case, luckily hes pretty handy. On the upside, it was fun responding to the Maytag customer service survey that night, LOL. All of our other appliances are Maytag and they have all been great, but this washer is an unreliable piece of junk.

I bought a model MDB7749AWW1 Maytag dishwasher in May 2011. I thought I was getting a nice one, but no one really liked the way the racks were designed after we got it installed and began using it. My biggest complaint however is with the control panel. It failed in November 2011 and was replaced under warranty. It has now failed a second time in June 2012 (just over one year old and out of warranty). Theyve offered to pay for the parts since it is so close to one year and I pay labor. Well see how that goes. Looks like there are lots of problems with Maytag control panels.

Christmas sale, needed a washer. Had a great experience with Whirlpool Duet so went for the on Sale Maytag Bravo MCT. No agitator which I thought odd. Bought the warranty. Did no good as soon as I hauled the washer home (3-hr trip one way). It wasnt washing my clothes clean. Hubby said try different cycles and soap and temperatures but at 8 months pregnant it wasnt long when I didnt fight with the machine but focused on a very busy life. Baby number 7 and I didnt care how the clothes washed as long as they didnt stink. Well baby is older, the warranty is not over and after much dialoging, no one will do anything for me. I put muddy pants in, they come out muddy. I put cloth diapers in, they come out smelling like pee. How hard can it be to come up with a machine that just turns clothes round and round with a little soap and water? Apparently really hard as Maytag failed to test this machine. Maybe city folk just have lightly soiled but on the farm with 7 kids, my kids play hard and their clothes are very dirty. They continue to stay dirty unless I wash them twice on Power Wash and Extra Heavy Load. Not impressed. Would like a replacement washer of equal or lesser value, anything that works. Oh P.S. I have the receipts and order number. Sorry its not put online to be verified buyer but dont feel like digging for paperwork at the moment.

My dishwasher was bought December 2013. The control panel just started going crazy and cant control anything. Unless you have bought extended warranty Maytag isnt doing anything. This is obviously a manufacture defect and no one is doing anything about it. Will no longer buy Maytag products if they cant stand behind their product.

I purchased a Neptune set in the late 90s when they first came on the market. I remember my delight - after the first use my clothes looked like new. Most impressive was I never needed to iron anything. Incredible. After 20 years of maintenance free operation, I finally decided they were getting too loud and was afraid theyd break down and spill water. Of course, I bought the latest version of Neptune again. What a disappointment. These machines are terrible. My clothes come out a wadded up, wrinkled mess. I have tried every recommendation in the book - the wrinkle free, the steam fresh, you name it. I have never ironed more iron free clothes before. Its added hours a week to my chores and we all look a frumpled mess. I really regret my choice. Strange that I cant wait for these new machines to break down so I can justify a do-over.

Dishwasher cleans well but the top rack is poorly designed for taller glassware. Unit has the typical features - wash, sanitize, rinse only, high temp wash, heated dry, light, normal or heavy wash, and delay start up to 6 hours. Standard dishwasher face; nothing fancy, no dirt catching features, very satisfactory. Electronic features (start, stop, etc.) broke after very little use. This is my second Maytag and a repeat of the first. Will NOT purchase this brand again!

I purchased the washer and dryer approx 6 or 7 years ago. Out of the gate about a year the pump had to be replaced on the washer- 2010. 1/2012 the tub needed to be replaced, 6/2012 the PUMP needed to be replaced again! Then 2013 the dryer need a new board at the tune of $391.00. And today, yes - yet once again I need a new pump! Over $2,000 in repairs on these awful machines. I called Maytag because I thought maybe they would care - not so much. The rep told me that the Bravos models were discontinued (shocker) but that she could give me a discount on a new comparable version at ONLY $600. How nice! I will use these until they fail again - which according to history - that wont take long and then I will NEVER EVER EVER purchase a Maytag product again. We work hard for our money and continually giving it to a company (for parts) for a product that they failed to make a quality product is not going to happen again! DO NOT BUY MAYTAG. Do your research and give your money to companies that care. MAYTAG should be held accountable and a class action suit should be filed. They need to GET IT and they never will if we sit back and let them take advantage of consumers.

Bought a new home in July of 2016 and the builder had included a Maytag Bravos XL washer and dryer. They are THE WORST performing appliances I have ever used! I will replace as soon as I have the means to do so. DO NOT PURCHASE the Maytag Bravos XL appliances. The engineers that designed them should be fired! The washing machine makes an incredibly loud noise (like an old starter grinding in a 50s car). Im told that this is normal for the machine. Does NOT clean well and leaves soap spots on dark clothes... leaves them on light clothes but I cannot see them. Whites come out dingy even with bleach. The tub is so deep that I have to use tongs to get out smaller items, I am 53 tall and have never had this issue before. Soap dispenser drawer wont stay closed during wash cycle. Clothes are so badly tangled during the wash cycle that it is hard to describe the wrinkled mess that has to go into the dryer.Dryer issues: Very loud. Very wobbly and unstable, and yes, it has been leveled 3 times. Bed linens have to be separated at least 3 times during the drying cycles because they twist and wad up into big, wet knots of cloth. Infuriating!!! Dry time is very long unless you wish to cook your clothes. So disappointed in this product. Total rubbish!!

After 6 months of use, I still HATE my Maytag washer. I will never buy Maytag again! The machine must be tricked into adding additional water to wash. It begins to agitate with very little water! Destroying my clothes! Also, I am having to hand wash all my underpants. They do not come out clean. If I could send it back, I would! Feel totally ripped off! I would give 0 stars, if I could!

We purchased a new Maytag washer and dryer from Home Depot; a couple months later the dryer started to rattle so we contacted Maytag and they sent a service tech out who stated this was normal as the dryer was settling and parts are not as tight as they are when new. This was a garbage response and he was asked to leave. I contact Maytag again, told them of the problem and the tech response and they offered to send another tech out except I would have to pay for the service call since they already sent someone out. I sent them an audio file of the rattle, no reply. Eventually Home Depot ended up replacing the dryer as Maytag refused to help me despite it being in the warranty period.

Love my washing machine. It is so big I need a step stool to reach down to the bottom. It cleans my wash well and I have dirty clothes. I hang my clothes on the line outdoors. My clothes have never looked and smell so good.

What junk. Bought this gx2shbxvy05 french door fridge. In less than 16 months the freezer is fine the fridge section gets up to 80f. Throw all the food away. Found the freezer coil covered in ice. Took the back panel off and noticed ice around the copper tubes by the compressor going up into the body. Not good. Put a small brick heater in and slowly melted the ice into the drip tray. Warning, it filled up 4 cups of water and of course spilled and killed the wood floor. After the clean up. Plugged the unit in and it seemed to work for about 3 months. Now its dead again. Looked into parts around 300 to 400 bucks plus labor to replace the system needed parts. P.S. the fridge, this junk replaced is downstairs working after 25 years not one issue other than the color. NEVER BUY A MAYTAG product please. TRAIL APPLIANCE should never have sold this product and should have stepped up to help out. Wont buy from them again.

Faulty control board. Have owned a Maytag dishwasher model MDB6769PASI for 2.5 years. The unit started beeping at random times for about a week - then went dead! Sounds like other reported failures and it is unlikely repairs will be permanent! Never again Maytag.

Before you purchase a Maytag washing machine...from anywhere (I got mine at Home Depot), think again. This machine doesnt wash clothes, it doesnt rinse clothing. What it does is takes forever to fill up the tub then it doesnt even come close to filling it to where all the clothing is covered for rinsing or washing, then it just stops and sits there for a few minutes (??) and then it proceeds to empty the tub and youre supposed to feel like your clothes were cleaned.Not in a million years will your clothing get cleaned in a Maytag washing machine. Youve been warned...dont waste your money. Go to a used appliance shop, but the best one they have that does NOT have the Govt. regs built into it, and be happy you saved as much money and did NOT have to go through all the frustration and hassle everyone else has that bought a new Maytag washing machine.

I bought this dryer 3 years ago and the fuse has blown three times. The dryer gets really hot and blows a fuse. The entire back of the dryer is clean and free of lint, the hose on the back, and the ventilation pipe running out of the house are completely clear, but the dryer continues breaking down. The Whirlpool NC folks have been out here three times yet it has broken down once again. I should not have to purchase another dryer after only three years!

Got woken up to the sound of my refrigerator ice lid flapping. Boy is it loud! Called Maytag and found out it was a recall so they will fix. They set up for someone to come out to fix the following week. That was a flop because they did not have the part. I waited 4 hours for someone to show to find out that Maytag scheduled the appointment for nothing - not only did they NOT have the part but they did not have a clue as to when it will come in. Time is valuable! Here we are 5 weeks later and my refrigerator is still flapping and loud. Has been calling Maytag for them to say that the part has been expedited. Well it has been expedited for more than 3 weeks now! Today they say that it will be another month before the part comes in! Not Good! This is such an inconvenience and Ive lost a lot of sleep over this flapping noise. Its an embarrassment when guests come over to our home! Tired of it!

Maytag 6.2 Induction Freestanding Range Model MIR8890AS0 F47 - I am a very careful shopper. I spent many, many hours researching and searching for the best value. It took me over 2 weeks of research to find an induction oven we could afford. We are a family of 3. Normally, we use just one burner for dinner. We bought the range in Feb 2013. On August 5. 2014, we had company over for dinner. I used more than 2 burners and the oven at the same time and the right 2 burners quit working; I now have the dreaded F47 code. I have had numerous Maytag Authorized repairmen out. They ordered every part except for the one that was necessary to fix my stove. I purchased in Feb 2013, burners went out 8/5/14. This is only 18 months old and is JUNK. Arent our landfills full enough?Maytag customer service is awful. I spent hours on the phone, mainly on hold, in efforts to get help. Maytag claims to have such a great 10 year limited warranty but they wont warranty this F47 issue. Thank God I bought insurance with an outside company. The wrong parts that were ordered were at least covered by my own insurance policy; no thanks to Maytag. I am angry that I have to search all over again to try and find the right stove. I am now fearful of induction. I invested in a lot of induction cookware which was an added expense and burden! They need to stand behind their appliances!People cannot afford to waste thousands of dollars every 1.5 years to cook their meals! This has been an extremely unpleasant issue. It has cost me many hours of waiting for repairmen, waiting on hold, getting and storing many wrong parts ordered by repairmen. I calculate this cost me over 50 hours of my life on the F47 problem. Not to mention the time it took me to shop for this junk to begin with!I think they need to recall this issue as it is clearly a design flaw. I researched this and found many other owners had similar problems. The F47 means that the user interface isnt communicating with the range (the circuit board). They placed the circuit board under the burner surface area, sandwiched between the burners and the oven. It was just a matter of too much heat before this board shorted out. The cost to replace this board is over $600. I am afraid of investing another dime into this machine. I wasted time, energy and A LOT of money on this inferior product.