We bought this refrigerator one year & 3 months ago & we have had various issues that are now no longer covered under the warranty. The pantry drawer has a peg on the side that is plastic & broke off on the right side. Will have to replace the whole right side panel. One of the door handles is coming loose which should be an easy fix, but its just annoying that it happened at all. Now the control panel is reading OFF/OFF & isnt responding at all. Tried unplugging for 10 secs, then plug it back in, but no luck. I cannot find any info online regarding this issue, so we will have to call Maytag. Hopefully, there is an easy resolution to this problem & we wont have to buy a new motherboard.

I tried to open the door to put clothes in the dryer and got severely shocked by 220 volts. The dryer is only a couple of weeks old. The power cord wasnt crimped and it fell out of the diggings and electrified the entire dryer. I guess we were lucky it didnt burn our house down. I took pictures then I fixed it myself.

I purchased this on sale at Home Depot, 1 year later this washer top load doesnt clean clothes if the cycle does finish at all. I have to restart the cycle, re-rinse etc, theyre still dirty. I dont have time for that, I have four children and my husband works in construction and comes home with filthy clothes that are just wet and dirty when they come out of this washer. I dont usually write reviews but I hope I can save someone else the hassle. I wish I would have read the reviews beforehand, they all complain of the same thing. This washer altogether is BAD! ITS LOUD, it bangs around if I dont put in the tiniest loads, even then, they come out dirty. Dont waste your time.

We purchased the Maytag MDB8959SAS0 dishwasher about 2.5 years ago. A couple of days ago, the lights on the control panel started blinking and beeping erratically. I contacted Maytag and they said the control board likely needs to be replaced to the tune of around $250, not including labor! We spent $800 on this dishwasher and it cant even last 3 years?? Ridiculous. The only other advice the service rep. had was that we should have bought the extended warranty. Gee, thanks. I guess with Maytag, you really DO need that extended warranty because their products are junk. I think I will just scrap this dishwasher and go with a Bosch. We also have a Maytag range that needed servicing after owning it for only 18 mos. And a Maytag dryer that needed servicing after a month (at least that was under warranty). I will NEVER buy a Maytag product again... they are complete junk.

I sold my 20 year old Maytag set and upgraded to this Maytag Bravos washer. This machine takes almost 1 hour to do a load and they come out dirty. Only way to get clean is to set on bulky sheet which uses twice as much water as old machine. This unit should have never been put on the market.

I bought this over the range Maytag microwave model MMV4205DH-1 5 months ago and today a hairline crack appeared alongside the door handle. I called Maytag to find out how I can get this repaired since, as time progresses, it will become worse due to using the handle to open and close the microwave. I was told this was a cosmetic warranty which expired after 30 days. They would fix it only if the microwave couldnt be opened. Apparently, the handle can become loose but as long as the door opens, they wont do anything.I bought Maytag because of their supposed reputation. Im so glad this happened with my $300 microwave as we were getting ready to replace our washer and dryer and were looking at Maytags. Good to know they dont back their products before I spend several thousand dollars on a washer and dryer. I will NEVER purchase another Maytag. My $120 generic microwave lasted 10 years and I gave it to my son and it is still going strong.

I purchased a Maytag Centennial Commercial Technology washer in September 2010 which is less than two years ago. It decides to stop spinning correctly in the Spin cycles. Clothes come out sopping wet so I contacted Maytag to have a tech come out. On the day that the tech came out from A&E Factory Service, he stated it was a switch. He changed the switch and still, it did not spin correctly. He then proceeds to state that it is another part, which again, it did not do the function correctly. He then proceeded to state that it is the clutch, then the transmission. The cost was raising to $519.00.I stated that I did not want to proceed because I would be purchasing a new washer with that quote. I stated to place all the original parts back onto the washer. He did so, but did not place them on correctly. The casing of the washer no longer is secured to the drum - bolts and plastic pieces are still on the side. He left my house with finger prints of grease on the walls. If this is the workmanship that Maytag recommends, then my business deserves to go elsewhere.A complaint was filed with the A&E Factory Service. However, no one has contacted me about the complaint as was requested. All I want is for my washer to be fixed or to have a tech who is knowledgeable to come out and fix it. I contacted Maytag to inform then of the situation and they stated that all their techs are certified. I do not believe that my washer of less than two years old could possibly have so many parts that are faulty. I hope that this may, in turn, help another consumer to avoid purchasing washers through Maytag and their parent company, Whirlpool.

My Atlantis dryer has never been able to be used on more/less dryer settings, I have had 4 repairmen repair my dryer 3 were while dryer was under warranty to fix the same thing 3 times wiring 4th time, anyway last repairman said my More dry wont work because I never had a sensor installed in my dryer and there is not a place for one so since 2005. Ive used timed dry only or my dryer runs all the time. I am concerned the first 3 repairmen never caught this. I should not have to be responsible for this either. Please have a manager contact me and have them check into my Atlantis Maytag dryer bought in 2005 and all the repair slips sent to Maytag.I used Green Yates in Joplin. Pretty sure. I thought I just had to live with it they would put new parts on I think timer, thermostats anyway can someone tell me for sure or inspect for yourself. I am single and dryer never used that much. Concerned Consumer, Nancy **/ Nancy ** as that name had front loader set from Maytag that I was very pleased with but sold with home in KC area, wish I had that set again I was very pleased .Thanks for your time.

The control panel of our Maytag dishwasher stopped working when it was approximately 14 months old. We repaired it ourselves by following a reset directions we found online (push rinse button 5 times and then the cancel button twice). Also we cut the power to reset. Im not sure which of those two tasks reset it, but it worked until last week - now 28 months old. We are not able to reset the panel using any information that we can find. In trying to find repair options, we discover that there are a lot of complaints about the Maytag dishwashers control panels not working within just a couple of years. In speaking with Maytag, they tell me theres a class action law suit for this problem - meaning they do realize there is an obvious problem with their control panels, but are not acknowledging they have any responsibility to repair it. The law suit only covers the cost of the part but not the labor. The labor can cost between $100 - at the lowest - and up. Our Maytag dishwasher model # is MDB8949SAM1. Also noteworthy, our Maytag clothes washer gave out at less than 5 years. Maytag is no longer the company we all thought they were. Additionally, their faulty machines are costing their customers a lot of extra money. Not exactly what I would call a company with good customer service or even any ethics. We will never buy Maytag again.

I purchased this washer from Lowe’s on 8/9/2017. After 3 years and 2 months, this washer would no longer power up. I tried resetting it by unplugging it and lifting lid 6 times. It didn’t work. The extended warranty from Lowe’s expired on 8/9/20. I called a technician and he found it need a control panel and control board. He suggested that I call Maytag to see if they would give me the parts as a courtesy since the washer was only three years old. I contacted them and experienced long wait times (51 minutes was the longest). I spent a total of 3 hours on the phone with them. They said no there was nothing they could do for me since the manufacturers warranty ended 2 years ago and the “mother control panel” doesn’t fall under 10-year motor warranty. Well, there’s no need for a motor warranty if there’s no power to the unit! The cost of the parts would be almost $600. It is shameful to not stand behind your product. I would expect to have to replace an iron or a juicer after 3 years, but not a washer. This was a major blow to how I would view the way they do business. I purchased the extended warranty from Lowe’s. I will never do that again. It was a waste of money. They didn’t make any concessions for me either. They kept saying it was a manufacturers issue.

I HATE this washer. It had such good reviews before I bought it, but I have never been so disappointed. Doesnt use NEARLY enough water to get anything clean, even when I try deep water wash, bedding, or power wash. You cant switch modes in the middle of a load, and if you leave it paused too long, it drains on you. Ive tried balling everything up as the manufacturer advised. I tried using less detergent, again as advised. Nothing works. Sometimes the clothes on top dont even get wet. Dont waste your money!! If I can find a way to fix my old washer, Im going to do that and throw this thing to the junk heap.

I purchased this Maytag washer/dryer set in February 2017 and I am very, very happy with it. This is a brand that has proven dependable for more than 80+ years. This is a low water washer that saves money on energy bills. I love the extra large capacity and was very concerned how well it would clean without an agitator. But having confidence in the name, which is why I purchased this set, I was very pleased with the cleaning power. The only disadvantage I see is with the soak cycle which is timed. I would like to have an option to soak indefinitely. So if you are trying to remove blood stains, you may have to use the soak cycle a few times before all the blood is removed. (Assuming that you are only using cold water and no additives.)

An average refrigerator/freezer at best. I would not recommend it unless you also buy a service agreement to fix things that go wrong with it. Ice maker went out.

I was all too excited to FINALLY own a new set! I conducted research and read reviews. We decided on the Maytag Bravo XL set (Lowes) and was thrilled! For the first 6 months. They were both fantastic! 6 months later, several times the clothes washed were soaking wet as if they had been set on soak. It continuously alerted to clean after 3 loads. The dryer... Well, evidently, if you live in a high-humidity region, DO NOT HOOK TO THE WATER LINE FOR THE STEAM OPTION. It will soak your dry clothes! After 3 loads of drying, it fails to re-start for the 4th load for at least 12 hours! When paying over $1,590 for a new set, this should not be an issue. Mind you, I do laundry once a week - 5 to 7 loads including linen. Fortunately, we paid an additional $200 for the warranty at Lowes.Lets see what happens there!

Before putting clothes in dryer you have to untangle them. Sweaters and even t-shirts become stretched beyond help. Clothes smell like mildew if you leave them in the washer even just a couple of hours. Im 50 and had a few washer/dryers and these take the cake. Ive used the washing machine cleaner/refresher (something I have never done on washers in the past) and still a mildew smell. The dryer has lint on both sides of the lint screen. And as stated before if you dont untangle your clothes they come out in a big knot, partially un-dried & very wrinkled. The lint on both sides of the screen concern me - Ive never had a dryer do that before. Its not much lint on one side but enough to think something is not right.

Mine is the Chrome Maytag four-burner cooktop model. About $700. I installed it with ease. After two years there are only one or two slight scratches. It sees full meals for two cooked daily. The grate is first class and looks new, the top itself is easy to clean with a damp soapy cloth and mineral oil. There is easily enough BTU power for any size of pro pan. The igniters are healthy and fine and a repair would be easy.

Purchased a new Maytag washer top load/Dryer set on April 1, 2016. Having trouble uploading receipt but I paid 1,145.83 for set. It took 2 weeks to get it delivered on April 15. 1st use it shook and wobbled even though the load was balanced but Ive read that is a problem with these machines. 1st load of clothes, washer didnt fill with enough water to wash properly - 3-4 inches of water for a full load of jeans. Top 2/3 of clothes hardly got wet! Changed the setting, same problem. Changed the setting again, same problem. I had to stand at washing machine and keep lifting the lid to get more water in the machine. Clothes didnt rotate in machine so all the clothes on top half didnt get cleaned. The spin cycle is scary! You could hear clunking noises and it had nothing to do with load being balanced. Did a small load and same thing with water level and spin cycle. Called Home Depot to pick up both machines on next business day. The dryer lint trap is so long, it made a mess trying to remove the lint even after only 1 load. NEVER AGAIN MAYTAG! Ive never regretted an appliance purchase like I do now. Maytag and April Fools day are a perfect match. Only its for real and not a joke.

We bought this Maytag dishwasher two years ago with a two year warranty. We paid close to $700. Six months after we bought it, it started having problems on and off. They are including: leaking water, lights going on and off, cycles are not completed. We changed the console once, and soon after that it broke down again, and this time is out of warranty. Total repair times are: 6 times in two years. My husband call the company, asked them if there is a recall for this model? They told that there is no recall. Then the repair person came. According to his repair experience he said this is the common problem and he got a lot of calls for the same problem. If he told the truth about this, then the company was lying to its consumers!!

We owned Whirlpool front load prior to the Maytag set we now own. Our Whirlpool was the better one. Shorter wash cycle, better cleaning & never had a problem with the seal. Maytag dryer doesnt signal properly when laundry is dry. You have to go multiple times. I wont purchase another Maytag set. We owned a Maytag top loader set and they worked like they should have.

Purchased a Maytag Bravos washing machine. DO NOT BUY THIS MACHINE. Disaster as the cycling is hit and miss. The clothes can take 4 hours or more to wash a load. And even then the clothes may still be soaking wet. Grandmas old wringer washer was better. DO NOT BUY MAYTAG. DO NOT BUY MAYTAG BRAVOS.

MDB4949SDM1 - After owning Maytag model MDB/C-2 for thirteen (13) plus years, I decided to purchase the subject Maytag Model when my 13 year old died. Big mistake. Previous model was very simplistic in rack design and it provided user-friendly options such as two detachable baskets for silverware and a special rack for delicate items.The new model has been designed so your dishes go in on angles on the top rack and as such bowls, small plates etc never stay in place once you move the rack and the lower rack configuration was redesigned and the rear area which was open to allow for bigger pots and pans to fit better has been removed, so now you have to lay your pans on top of the tines, very difficult to low the dishwasher.Additionally, I purchased the stainless steel model; apparently in the coating process a drip pattern was sealed that you can see when sunlight hits dishwasher. Further the stainless steel face that they bond to the door has popped, so when you grab the handle the face pops in and out. Lastly the new design has an adjustable upper rack; I tried numerous times to adjust the rack and couldnt so when I called Customer Service for these issues, it basically boils down to if the Service Man comes out and determines my issues are cosmetic and the rack which Ive never been able to adjust should happen to work then I have to pay the service call as there is not warranty coverage. So I declined the Service Call and advised that this would be my last Maytag purchase. I highly recommend anyone considering this unit fully investigate and test out before buying.

I give the product lowest and poor rating. The bearing in our washer went bad 4 months after we bought it. For the fourth time, they are coming out to repair the washer on 01/11/2012.

I purchased my first Maytag dishwasher and it was recalled as being a fire hazard. I was offered to have it repaired or pay for an upgrade (approximately $200). I chose to pay and upgrade because I dont want a fire hazard in my home. After my paid replacement, I received a recall on the new dishwasher regarding the same issue (different model) and I chose once again to pay and upgrade (thinking that if I spent $700, I wouldnt have a problem). In less than two months of installation, the dishwasher died in the middle of a cycle. Filled with water, I bailed it out and called Maytag. I told them that I wanted a new one and they told me that I was past the replacement period. They sent a service man out and he stated that it was a problem with model # MDB7709AWB2 and serial # F03002958. He said that it was easy to fix and said he had done it several times. So now, within less than 1 month before my warranty is expired, the dishwasher did the same thing--it died in the middle of the cycle and wont turn on. I called Maytag and they told me that they would send out a third party repair company (JD Appliance) but I would have to wait for four days. I contacted Maytag and said that I was concerned about the dishwasher breaking down again for the same problem (bi metal unit blew). This is the second time it happened. Jeremy, the repair man, said that the first replacement was not installed properly and they should have replaced the entire unit. He stated that it was a common problem with that model, as did the first repairman in Dec 2010. When I spoke to a supervisor named Kia at 800-344-1274, she stated that they had no known issues with this model. I said that it was not what the repairman told me as well as the Maytag dispatcher. They both said that the heat sensor (Bi Metal Thermal Unit Part No. W10258275) goes up and has to be replaced because it is overly sensitive. If you are out of warranty, it costs around $200 to have it fixed. I told Kia and she said that it was not documented in her file, therefore, it never happened. I want to know my consumer rights to address this issue. I have paid for (on 3 occasions) a new dishwasher and have continuous issues that cost me money. I want an assurance like an extended warranty, free of charge, for the dishwasher that has already been repaired twice for the same exact problem. I have the original part that was improperly replaced to prove that it wasnt replaced to specifications, therefore, blowing it again. I was told by Kia that Maytag does not compensate or replace their products unless deemed not repairable by the technician. It doesnt matter how many time the same problem occurs. I would appreciate your attention to this matter.

This is a portable dishwasher. It does a great job washing the dishes. It’s fairly quiet and gets them very clean. It moves quite easily. The silverware tray is generous. The cycle takes a bit of time, but I don’t think it is excessive compared to other brands.

Maytag Bravos electric steam dryer purchased 2009 - I have had to replace the door hinges within one year of usage at my expense. The blower belt and pulley had come off twice, the last time about a half hour after the repairman (again at my expense) left. I put it back on myself and if it comes off again, I will use Locktite to glue it on the blower shaft. I figure I will be lucky if this crap lasts a couple more years anyway. No more Maytag for us! What does it take for the consumer to get some representation with regard to lemon laws here? I will take my wrath out on Home Depot here since I have no recourse. If enough people complain, maybe they will stop selling that junk. I also will disregard Consumer Reports in the future.

Purchased Maytag dishwasher from Ft Knox Exchange in 2011, Model MDB6709AWW1; Serial # F04117463. Like most posts before me, the panel started failing after 2 years. Unit is now inoperative. I am attempting to fix myself using repair techniques Ive found online as I refuse to pay hundreds of dollars to repair this piece of junk. Will never buy Maytag again.

Bravos XL Like so many others Ive read, this is a terrible product. Washer constantly goes off on unbalanced load. After 14 months, the plastic tub disintegrated. Maytag tried to sell me the service and extend a warranty for $300 also. Just like all the other reviews. Wow, has Maytag gone downhill.

We have a Maytag drying center that is almost 6 years old. It never did a good job drying especially for the money we paid, but it just quit on us two weeks ago. We purchased it from TA Appliances in Barrie, Ontario who recommended that we call B&K Appliance repair to fix it. The owner showed up and said he would be back to us in a few days to fix it, as soon as part arrives. He now wont return calls and it has been two weeks, so we called Maytag customer service. We knew we were in trouble when we received a message telling us Due to higher than normal call volume... (so much for the Maytags that never need repair). Anyway, we finally reached an incompetent, ignorant and anti-customer service representative who proceeded to tell us in an extremely, nasally drawl that the part needed to fix our 6 years old dryer is no longer available and the most they could offer as compensation for this on our $1500 plus tax dryer that should last at least 10 years is $120. This is for a dryer we never used more than 5 times a week.

I purchased a matching set Maytag washer & dryer June 2013. Sept 2013 the drum went out - 4 weeks for that repair. March 2014 the electric panel went out. Took about 10 phone calls with hold waits of 30 to 70 minutes and 4 months, to find out the replacement part is no longer available and the washer is discontinued. To get a new matching set, I had to pay for a new dryer and they will give me a free washer. I have to give both washer and dryer back - I paid for 2 dryers. 6 month later and more phone calls, no washer and no one will return my calls. The dryer I paid for is at the appliance store waiting on the new washer. We consumers have nowhere to go. I have heard so many similar situations. Where are we to go? Who are we to call?

Maytag Bravo Quiet 300 dryer(less than a year old): #1, on timed dry setting machine cuts off before the set time, clothes still wet. Needs multiple cycles to achieve drying, then you get wrinkles. Cannot manually set time, its automatic. Technicians (2) have replaced sensors and tinkered with timer, no fix, no documentation to show what was actually done.

I have had a number of Maytag washing machines in my life and have never disliked a machine as much as the last one I purchased! The bleach dispenser is awful and any bleach that happens to land on the outer rim has ruined many clothes. I took them to my dealer to show him the ruined clothes and was told bleach does not evaporate do must be wiped off each time. With no soap dispenser I find I have to put the soap in first and keep trying to fill the machine some before I add the clothes. This takes forever but if dont do this my clothes are stained. I purchased this machine on April 11, 2017 and can not afford to go buy another washer at this time. The Dealer can not help me and when I called Maytag they were not interested! Buyer beware!

We purchased our washer and dryer set in December of 2010 and had it for about 2 years with the extended warranty...needless to say around 1 1/2 - 2 years the metal around our bleach dispenser started rusting. Maytag considers this cosmetic! I am shocked to think that its cosmetic...on the outside of the washer yes, but on the inside no! It is faulty on Maytags part. I have spoken with Maytag and they tell me if it doesnt happen within the first 30 days there is nothing they can do. So I will tell anyone and everyone what was said to me via Maytags own repairman, Buy cheaper washers as NO ONE offers an extended warranty on the inside of the washer rusting. Whirlpool is the owner of Maytag now so beware of Whirlpool as well. Check out the warranties and make sure you will be covered longer than 30 days for rusting on any washer you intend on purchasing. We learned the hard way and well....we will be buying a cheap washer like the repairman suggested when this one goes out.

We purchased all Maytag home appliances when our home was remodeled about five years ago. After the first year, the microwave had to be replaced because it malfunctioned. The dishwasher stopped working in the third year, and now, my refrigerator (model# mf12568AEB) wont cool. The technician told me that all of the Freon had leaked out because of a design flaw. Moisture had gotten into the compressor, and with the cost of repair or replacing the compressor, I would probably be better off buying a new refrigerator, preferably not a Maytag.

This oven isnt even worth talking about. Just dont buy it. I used to bake a lot, but my recipes dont turn out anymore. My old oven was much easier. I dont know what the problem is, but I suspect it is oven temperature. The door also sticks. I have only had this a year and am ready to junk it.

We purchased our Neptune washer and dryer combo MLG2000AWW from Circuit City in 1999 for $1900 also purchased the extended warranty. Here we are 15 years later and time to replace with new Samsung units. Besides having the main bearing replaced after 6 years in service, and having a sensor and a switch replaced on two separate occasions all covered by the warranty, our Neptune provided exceptional service throughout the 15 years. My understanding was that Maytag was bought out and run very poorly in the early 2000s as our unit was produced prior to that time... when Maytag was Maytag.

I bought a Maytag dishwasher Model MDB7749SBW3 from Home Depot 6/2014 and by December 2015, the touch panel was going crazy! Ive read a lot of reviews and this seems to be common for Maytags. It would cost me almost as much to have this machine repaired, with a service call and the cost of a new panel, as it did when I bought it. When talking to an appliance repairman, he informed me that Maytag and most all the major brands are now owned by Whirlpool and that they are basically junk--not meant to last more then 1-3 years! Where are the recalls and how do we get a recall started?

I have gone several years with wasted food at random times because my Maytag refrigerator decides to stop cooling whenever it feels like it. This is a continuing thing that started since the appliance was brand new and it has never been resolved. Maytag claims that they cant do anything about my refrigerator. They can do what they want to. From my experience, I feel like the issue is that they dont care to make it right. I am finally fed up with this refrigerator and I am buying a new one. I can guarantee that it will not be a Maytag.

Maytag Smoothtop Double Oven - Bought this stove 2 and 1/2 months ago and already buttons arent working. Very disappointed, not getting a Maytag again.

This product was purchased in March. In September, the agitator broke off. Thats a new one on me with a washer. Every other one Ive bought tended to last 10 years or so, then something like a motor wore out. It was an obvious design flaw on a topheavy agitator held on by a flimsy plastic sleeve. To make matters worse, their warranty service seems mostly geared to selling extended warranties, necessitated by the poor quality and bad design of their products. So, for a mere $182, I can have it covered for the next six or seven times the agitator breaks. No thanks, Ill figure out how to fix it myself when its no longer under warranty, or just cut my losses by buying another machine, and never another Maytag or Whirlpool product. I had a similar experience with a Whirlpool refrigerator purchased in April 2017, which had a defective module that went fortunately just before it was out of warranty.

I purchased Maytag dishwasher Model #MDB7749SBW in November of 2013. The front touch panel no longer works. Everytime I push the selection for wash it automatically jumps to Cancel. This dishwasher is less than 2 years old. I didnt purchase the extended warranty simply because I thought I was purchasing a very reliable product. Lonely Maytag Repairman of old. Ha Ha. I am very disappointed and am telling friends about this and all of the reviews Ive read that are similar complaints. I would never purchase a Maytag product again.

I had a brand new Maytag refrigerator freezer delivered to my home. Not three days later, the freezer compartment is frosting over on the back wall, while the refrigerator fails to keep my drinks cooler cold like I demand. Ive heard of planned obsolescence, but this is ridiculous!

My Bravos Washer and Gas dryer are only a few years old, and they have both been problematic to say the least! Neither Home Depot nor Maytag have been helpful. My washer has had the shocks replaced already, because it would constantly go off balance and shut down and they cant grease the bearings because they are sealed. So, now it sounds like an airport is in my laundry room! The gas dryer takes an entire day to half dry a load and its burnt on the inside!

After reading all the reviews I realize this is a wide spread complaint. After 2 1/2 years the control panel on my Maytag Dishwasher will not work. You press the keys and hope for the best. I am thinking of going to the media with my complaint. Maybe we will all get some sort of refund or upgrade.

We bought a new top of the line Maytag MGD7000XW dryer about 2 years ago. It worked great for about 6 months, thing started acting funny. All of the front console lights stay on all of the time and it ONLY dries on high heat now. This all happened after the warranty period. So fine, I was going to buy a new complete front console (CONSOLE Part Number: W10388467 $300.) as the online repairman suggested. Guess what, Maytag no longer offers the part to fix my dryer. So now I have a 2 year old top of the line P.O.S. MAYTAG dryer that cant be fixed. I will never buy from this company again (Maytag).

I purchased a Maytag Gemini gas range in July 2006. Rust has appeared on the bottom of both oven doors. I called Maytag customer service, realizing that my range was no longer covered by warranty. However, I feel the paint on a range, costing over $1,000, should last longer than 5 years. Customer service told me to call a repair technician. When I asked who would pay for this service call, they didnt even bother to respond to me. As I have read other reviews of dissatisfied Maytag Range owners, Im glad I didnt waste money calling a repair tech who would do nothing to help, but charge a $100 plus fee. The paint on a car, which is subjected to all kinds of weather, lasts much longer than 5 years. You would think the paint on an appliance inside a home should last much longer. This rust is becoming very unsightly. I will certainly not purchase a Maytag product again, as the company has proved they do not stand behind their product line.

I have owned three different Maytag washer/dryer sets. The reason for so many? Selling the set with the house upon moving. I kept my last set which is Bravo. I love Maytag for their features, their dependability, their reputation. I have never had repairs on any of them. Totally awesome! My second set had a neat feature of a drying rack where you could place a sweater or shoes and no tumbling. Sorry I sold that set w/ the house. I am very pleased w/ my present set of Bravo. No agitator. A coworker also bought this set. Maytag is the best!

After researching the top-rated washing machine in consumer reports, we decided to spend the extra cash ($930) and buy the top-rated machine. Spending almost double on a high end machine, you would expect this machine to last longer than three years. The motherboard needs to be replaced because it gets stuck on a UL code near the end of the cycle. Now, we have had two people come try to fix it, and they said to trash it and buy a new one. Only three years! If I had paid $300, I wouldnt be so upset, but that was a total waste of money for it to last less than any machine Ive ever had. How is a consumer supposed to know what a good washing machine is if they spend extra cash for the top-rated machine and that one is still bad? The company should replace something like a motherboard that goes faulty when it had nothing to do with use. So unfair and frustrating.

Stay away from this product!!! Lets just say one star is too much for this product. Terrible. Lets just say one star is too much for this product. We bought this washer 2/2017. We used our previous Maytag washing machine for about 15 years without any problems. But this machine on the first try was a big disappointment because it did not wash clothes very well. Clothes come out of washing machine smelling bad and you could see the soap scum on darker clothing. We try to return the machine to Home Depot after 3 days, but they said after 48 hours they could not take it back. So if there was any problems we had to call a technician to repair it. Well, there is nothing to repair because thats just the way the machine is designed to conserve water.Worst washer and the customer service is even worse than this machine because they just keep repeating that if there is nothing to repair then, there is no problem. So, therefore its not their responsibility. TERRIBLE!!! I even bought their extended warranty and that doesnt do anything with dissatisfaction on this product. If you are owner of this company or at least care about your company, you should stop making this kind of product, and listen to peoples complaints!!! What a waste of our hard earned money in this bad economy!!!

We bought a Maytag appliance package when we built our house in 2015. So far the exchange Fan burned out in the fridge. The element burned out on the range. The wheels broke off inside the dishwasher on the racks inside and the outside of the white dishwasher is rusting worse than 1959 Edsel. 3.5 years old. Broken and rusty. I called and emailed Maytag customer service and all they say is it’s out of warranty and they’re sorry. Things break I get it but if they said on the box when I purchased it that it would rust in 3.5 years I would have looked at and purchased another brand. Beware of the cheaply made poor customer service of the new Maytag.

My washer is great. It get the job done. Have no agitator so I can wash 2 comforters. I really like Maytag Heavy Duty. Can get the job done right the first time. Self clean itself also. Also it is a efficiency.

I purchased a Maytag Bravos Quiet Series 400 in 2010 and it is now leaking like crazy and sounds like the bearings are going or gone in it. I researched washing machines for over a month before purchasing, and it seemed like this would be the machine for our active family. So much for research. It washes clothes okay, but is a bit rough on them. I found that it has ripped some of my more delicate items. When I contacted Maytag, they sent me an email with contact information to purchase a maintenance contract for $395 which would cover the machine for only 1 year. My husband is very mechanical and took the washer apart thinking the seal/gasket may have come off. He cleaned up the seal and the area around it, and put the seal back on. It did not help. He also noticed that the drive shaft to the motor was beginning to RUST! This machine is only 2 1/2 years old! So, if you are noticing that your whites are getting orange spots on them, this is probably happening to your washer, as well. Maytag should step up to the plate and recall this machine.

We too bought a Maytag range (MER5755QAW) approximately 5 years ago. While making Christmas dinner, it quit working. The oven would not heat. Too bad it had to quit that day (or at all for that matter). Unfortunately, every single appliance I bought for my house 5 years ago is a Maytag appliance! The microwave quit last month and I have yet to replace it. I bought Maytag because for the longest time it was such a positive household brand name. Unfortunately, with 2 appliances less than 5 years old and out of warranty, I will never purchase one of their products again! I will spend the extra money and go with LG especially after reading some of the reviews on here on Maytag’s products (there are over 192 complaints on the Maytag ranges and ovens alone on this one forum).

We have a Maytag dishwasher that came with the house we purchased in 2012. Im not sure of the exact age but the former owner said it was a relatively new installation. The appliance works very well; cleans well. Just a couple of things of concern. First, it is really noisy. The fact that we can very clearly hear it running in the adjacent room does not speak well for it in this regard. The other things that has occurred is that rusting is evident on the trays of the dishwasher. One of the upright pieces has already broken off due to rust and two others are close to coming apart very soon. Nothing sharp is placed in those areas that are coming apart so there would be nothing remarkable to disturb the plastic coating on the wire racks. I can only conclude that the plastic coating was defective at the start; hence the rusting at the base of the upright pointing racks. That said, it does clean well but I dont foresee this unit lasting much longer overall due to the rack damage that is continuing to occur. I would expect the racks to at least last as long as the dishwasher but this does not seem very likely at the rate the racks are deteriorating.

I have a 50/50 chance of completing a wash cycle. Most times, the washer stops working at 8 minutes remaining in ANY cycle. The washer will leave me with wet clothing and refuses to spin even when most wet, dripping articles are removed. I have tried to put all light-weight items together and that still is not a guarantee that I can get this done in one cycle. Most often, the error code comes up, I spin the drum around, move the clothing around and try again. This process is NOT energy efficient which is why I bought the ** thing in the first place. I am ready to put it on the curb for the trash man to pick up.We had a service person out and he said it is either the bearings or the motor (both a $400 job). I will NEVER buy another front-loading washing machine. At least with the old-fashioned top loaders you can get the load balanced and at least get clothing to go through the spin cycle. I am now hand-wringing clothing once again since the machine tells me when it will spin my clothing. That stupid chime is about to send me out of my mind!

I have a Maytag washer that I bought new in 1995! It is still washing my clothes like a champ. It must be true - the Maytag repairman is a lonely soul, in all these years I have never had to call him!

Maytag MVWC300BW clothes washer makes holes in heavy duty T shirts & sheets. It stretches clothing. We are following directions in loading without success. We are washing everything on the gentle cycle twice to get the clothes clean without destroying them. Today we were stood up for our third service call.

I have had this machine for 15 years and never spent a penny on any maintenance, I love it. Some things are worth it and it still has a stylish look and cleans great. The only thing I would change is if it didn't have any the middle washer paddle so it would have more space like the newer models.

Our refrigerator is just 2 years old and it have been leaking for over a year. It started leaking right when the warranty expired. I am so mad. I called them and they said... You can purchase a warranty for $400. I am like.... what!!! I called my home warranty and they fixed it for $100. A few months later it is leaking again! I am so mad... It is a $1200 refrigerator. What can we do as a group to fight for this? There have to be something that we can do?? It is so frustrating. If there is an attorney that can take care of this group that would be great.

Purchased a Maytag dishwasher in 2009 then had it repaired for a leak in 2010 (just past the 12-month warranty); next another leak in Nov 2013 so purchased another Maytag as repair appliance company said it wasnt worth fixing. Now in Feb 2015 it is leaking Again! So 2 dishwashers and 1 repair in 5 years! Both were purchased from Home Depot. I will Never buy a Maytag product again.

I purchased it 8 months ago. I have had problems with the machine leaving clothes soaked at the end of cycle. I have contacted Maytag (still under warranty) and they replaced the motor. The first load after repair still had the same problem. They said the check drain was not clogged. The snaked drain has no backups. After every wash, I have to reset the cycle to drain and spin. The machine spins for seconds and fills back up with water and doesnt spin again, but does drain. Clothes are sopping wet at the end of cycle. I contacted Maytag. They said I could be billed for customer education ($129) if they find no problem (threat). I want my money for purchase returned or at least 3/4ths. I expected my new machine to last years, not months.

Apparently the Maytag Bravos HE top loading washer is poorly designed. We have sparingly used this washer for approx 3 years and it began to make a horrible noise in the spin cycle and then to give us UL error codes. After searching on the internet we discovered that the seal around the main spin shaft and the bearings were bad. Inspection under the machine revealed a terrible rust and grease spot and splatters of rust and grease on underside of unit. This is a typical problem and this machine should have been recalled or at the very least repaired by Maytag for little if any cost. They now make a kit to fix this problem, but this should not happen after only 2-4 years of use on a $700+ machine. Very, very disappointed with Maytag! Customer service, of course, offered us nothing as pathetic 1 year warranty was expired. Ten year on the tub, like anything will go wrong with that.

I have spent a lot of effort leveling my machine, and my wife balances the load very carefully, but 10 times during a cycle, it will start slamming the tub around, so loud you can hear it from the street. I, like others in this forum, thought I was buying the best washer in the market, and paid extra for the Maytag name. It sounds like from the other complaints, that my problem is just the tip of the iceberg. It will cost me $200 to replace the suspension rods. I wouldnt mind paying the money, if I thought it would fix my problem. After reading about all of the other problems with the Bravos, I might just cut my losses, and get a new one. What a waste of $1,000.

I have had a few dishwashers in the past, however this is the worst product I have ever purchased. After a couple of years in service I needed a new control panel which cost $200.00. The dishwasher defaults to heated dry and the exhaust for the dishwasher is right behind the copper electrical runs so it corrodes and fries the runs. The way I see it Whirlpool and Maytag saw a unique way to gouge its customers for parts. They also have a rope and plastic cable system that attaches to the door spring that continues to break cost $28.00 a piece, I have replaced two. Now I see that one of the pulley guides (plastic) is broken and split cost??? Here is another brilliant engineering feat, the door panel clips into the control panel so that when the door is pulled in a normal fashion it comes loose. If you buy this line of dishwasher (p.o.s) plan to work on it and buy parts on a constant basis. Here is my advice: buy one control panel, two cable systems, and a couple of cable pulleys or buy a cheap dishwasher as a replacement and save some money. Run from Maytag or its parent company Whirlpool - let the buyer beware.

If I could give this a 0-Star rating, I would! I cant believe Maytag would make such an awful washing machine! Within the first 2 weeks I called their service department because (in my opinion) the washer wasnt washing properly. It took over a month and several calls to get someone out to look at the washer & dryer. According to the technician, both machines were operating properly. Apparently the washer is designed to destroy clothing and bedding! The gentle cycle set on deep fill will add just enough water to get the clothing wet, then agitates for about 10 minutes, then it fills up, agitates for 3 more minutes and drains. During the 10 minute dry-run, I watch my clothes get destroyed! I have never seen anything like this! My sweaters are shredded, my tops are pilled up & in a garment bag this thing managed to destroy a sports bra! This machine has ripped my mattress cover in several places and pulled my sheets from excessive rubbing due to not enough water. And what is up with the slow fill? The technician informed me that the trickling water is also normal. If I could return this washer, I would! I will never buy another Maytag because my Bravos washer died after only 4 years, and this one is brutal!

Why are the clothes in my dryer getting stuck in Maytag Neptune? It seems there is a little opening around the rim of the barrel in the back of my dryer that drawstrings, zippers or similar small parts of the clothes can get stuck in. It twists the clothes around and is ruining clothes, also is making a thump-thump sound. Someone, please help!

I bought a Maytag dishwasher (MDB7749SBW1) about 4 years ago. Ive had to replace the wiring on the control panel each year. This is clearly a design defect, and Maytag will not take any responsibility for it. Ive called each year, and am told each time that theyve never received a complaint about this issue. This year Im replacing the dishwasher. Ill never buy a Maytag product again.

My Maytag dishwasher MDB7749SAM is not quite 5 years old. At the end of December 2016 a bubble appeared on my vinyl floor. The plumber could not find any broken pipes or reason for any moisture to have gotten under the flooring. A flooring company did not know what was causing the bubble, moisture or the vinyl glue had failed. The floor got worse and worse, more bubbles.Called the flooring company again. Raised the register cover and could see all the moisture under the vinyl and underlayment. Plumber discovered the dishwasher fill valve had failed but because there was so much insulation on the kick plate, at the bottom of the dishwasher, it forced the water, which was in a pan under the dishwasher, to push the water to the back by the wall and under the flooring. Plumber said, the insulation acted like a dam to keep the water from showing in the front of the dishwasher. The first and subsequent bubbles, in vinyl were 3 feet away from the dishwasher. No way to tell the dishwasher had the problem. Has anyone experienced this problem? If not, take care to remove the kickplate and check your dishwasher for water problems.

Our Maytag Bravos Quiet Series 300 is anything but quiet. Within two years of purchasing it, we now hear an F18 jet fighter taking off from our laundry room. Neighbors near and far come running to avoid getting injured when the spin cycle kicks into after burner. Seriously though, this looked to be a nice machine and operated flawlessly until a month ago when the spin cycle started sounding like a jet fighter taking off. I am handy and often fix appliances and things around the house. From reading reviews here on Consumer Affairs and other places, I am finding that the noise problems are more common than not. Investing $400+ into a replacement tub/bearing set would further support Whirlpool/Maytag and the sucking sound they make to get at my wallet. From what I have read, I am likely to have more problems after fixing this one (it will likely break again). I am going to quit while I am ahead and purchase a new washer. Whirlpool/Maytag will never see my business again. Its ludicrous to have an expensive appliance like a washer only last two years. BTW, I just spent $200 to replace the control panel on my 4-year old Maytag dishwasher. A cheap and horrible design. The part probably cost $10 to make. BOHICA. (bend over, here it comes again). FYI: Whirlpool owns and sells its products under several other appliance names. Names that include, Kenmore (yes, Sears), Maytag, KitchenAid, Jenn-Air, Amana, Gladiator GarageWorks, Inglis, Estate, Brastemp, Bauknecht and Consul (Wikipedia source). Like a Lotto Scratcher, peel the Whirlpool or Maytag name sticker off and underneath you will find the real name... CRAP! Its sad to think that you have to purchase products made in Korea to get quality. Very sad.

We purchased a Maytag Bravo Washer and Dryer in late 2007. We had a one-year warranty on the set. At just over 2 years, we started having problems with the washer. It started making a loud noise when spinning and started beeping all the time during the cycles. We contacted Maytag and they said the only thing they could do for us was to sell us an extended/repair warranty for $320.00. If the cost of fixing the machine was too much, they had the option to replace it with another machine equal to the value of the machine in todays market, or cash, or a gift card equal to that.We were angry about the cost of the warranty and we were unemployed at the time and couldnt afford that so we just had to let it go. The machine progressively got worse where only two of the cycles would work, but not without beeping several times where you had to fix the load, and the sound got so loud it sounded like you had a jet plane just overhead. Just the other day it completely quit working. We have been in contact with Maytag several times but their only answer is their repair warranty. Weve talked to numerous appliance repairman, who all knew exactly what was wrong because they have seen it so many times, and they told us that we have several things going wrong with the machine we would probably need a new drum, a new drain pump and a new control board.We were told that it would cost more to just buy the parts than it would be to buy a new machine. In the course of our phone calls to Maytag, they have continually told us that they are sorry but there is nothing they can do, in fact they only have record of two of our calls (how convenient!). Since experiencing the issues with the machine, we have researched it online and found that scores of consumers are dealing with the exact same problems we are having which shows that there are defects in the manufacturing of these machines. Maytag should be forced to fix these problems. They are well aware of them and they should have to back up their products.There should be a class action lawsuit out against them. We were told by an appliance repairman that Whirlpool (who bought out Maytag) has a washer called Cabrio that is the exact same model as the Bravo and that they do have a class action lawsuit out against this model. Consumers that purchased the Bravo should be included in that lawsuit. I am stuck with a broken down washer, mildewing clothes and dont know where to turn outside of paying out the money for the extended warranty with no guarantee of what we would get out of it, purchasing a used set with no guarantee, or putting out the expense for a new set.This set was an expense set and we went with Maytag because they used to have a good reputation, but we feel like we have been totally cheated. If the appliance companies were forced to offer a longer warranty on their products, they would have to manufacture them at a higher standard. For the cost of these new machines this is exactly what we as consumers should expect. Please help us to know which direction to go. Even with purchasing a new machine we are apprehensive!

Failure to drain after 3 years. Was disappointing so repairman fixed problem, a fuse, in 3 minutes but charged $300! Since then I make my own repairs and have had no problems that I can complain about. Both Maytag Neptune drier and washer have worked well. Buzzer just failed.

We bought our new Maytag top loading washer and matching dryer about 2 years ago. I am a busy woman so I havent had the time to write a review, but today being my day off, once again I find myself frustrated and disappointed with this set. The washing machine has a huge capacity, which was a huge selling point for me, however, if I put more than a small load in, the clothes come out still dirty, stinky and even have dry spots on them where they werent even in contact with the water. Even on deep fill it cleans the clothes inadequately, but at least they get wet. The dryer leaves the clothing rough and wrinkled unless I use the delicate setting, which I do for all cloths, and I use fabric softener liquid and a dryer sheet.I had a front load washer and dryer before, and my clothes came out clean and beautifully soft, but I replaced them because of the musty smell problem from the washer. I wish I would have kept them and figured it out. This set is the worst and I spent so much money on them. It takes so long to wash a load of laundry, and there is no way to interrupt a cycle without it draining and starting over completely. I have tons of laundry to do and I started 2 hours ago and the first load is still going. Geesh!!! Dont buy a Maytag. I paid for the extended warranty, but they are not broken. They have sucked from the very beginning.

I purchased the Maytag Atlantis Washer and dryer in 2004. I had the washer transmission replaced in 2006, I believe. For about a year now, the washer makes an awful screeching noise. I am not sure if its towards the end of the spin cycle or the rinse cycle, or both. In addition (and over the last 3-4 years), the dial sticks or stalls every delicate cycle. It will stop during the initial agitating and all you can hear is a ticking noise, in which you then have to manually give the dial a slight turn for the cycle to continue. It does it once on the light delicate and twice on the normal delicate. It really is a shame that Maytag is not acknowledging all of these problems as it is not feasible for most people to have a spare $1500 kicking around for a new washer and dryer every time they unfortunately buy a lemon. My previous washer and dryer were 25 years old and still working perfectly when I decided to part with them because they were fairly small. I dont even ever recall having any issues with either one of them in the whole 25 years that I had them. To see all of these complaints makes me more irritated with my appliances and my selection!

I purchased a Maytag Bravos XL washer and dryer at Best Buy (Pacific Sales) in March 2013 at Best Buy. I also purchased extended warranty on both machines. A few months into owning the machines, the washer started giving us a UL error light. It wouldnt finish the wash cycle and had to be restarted multiple times before it would do so. I called Best Buy and they sent out a repairman. He said the set-up cycle had not be run correctly by their own installation team (which I paid for), and he said that he had fixed it.A few months later the problem started reoccurring again. Best Buy sent out repairman again who claimed there was nothing wrong with the machine. He left and the problem started reoccurring soon thereafter. I called again, and Best Buy said they couldnt do anything about it because Maytag could only work on the machine (it was now getting an F:51 error message as well). Maytag sent someone out who watched it run for 15 minutes and diagnosed that it was fine and left. I told him that the error didnt occur until the end of the cycle, but this seemed to make no difference to him (he didnt want to wait).Same thing happened again (might run five to ten loads without an error and then it pops up again), and I called Best Buy again. They sent out the Maytag repairman again (different repairman). He spent about the same amount of time as the previous Maytag repairman. His conclusion was that the machine was fine; he told us that this particular washer (the top-of-the-line for Maytag) gets out of balance frequently and that we would simply need to live with it. Like his colleague, though I told him that the error message doesnt occur until the end of the cycle, he didnt stay that long.Not long after he left, the problem started occurring again. I called Best Buy and indicated that theyve had plenty of chances to repair the machine and that I wanted a new one. They said someone would call. The response: another call to schedule a repair visit. I called them back and told them that I didnt want another repairman but rather a new machine (weve wasted hours and hours of our time giving them a chance to make the purchase right). They then had someone from the Geek Squad call, who swore that hed put his best guy on it and that he would actually work on it this time (ordered parts). He was supposed to show up this past Friday but called in sick (now rescheduled for this coming Friday). In the meantime, the machine (last night) quit working altogether. I have a pile of wet laundry and am faced with going to the laundry mat today.Im at an utter loss of words for this experience. It is truly the most frustrating consumer experience that Ive ever had. Ive watched Best Buy, Pacific Sales, and Maytag play pingpong back and forth across the table for months. I paid good money for top-of-the-line washer but have gotten bottom-of-the-line service. Surely, at this juncture, Maytag and Best Buy will finally do the right thing. I am going down to the Best Buy store this morning to visit with the store manager (and then to the laundry mat...not exactly how I wanted to spend my Sunday). If not, then next steps will be to figure out how to find representation to force the issue of the lemon law. Exasperated.

I bought the dryer (Maytag Gas Bravo Dryer) from Home depot in December of 2010. The thermostat went out in July of 2011 and has replaced the same part 5 times up until August of 2011. Then they put a new burner with a thermostat and it lasted till June 1 of 2012. Now the warranty is out, they want me to repair this piece of **. I will never buy a Maytag product again.

My stainless steel french door refrigerator started to rust 4-5 months after purchase. Upon contacting Maytag/Whirlpool I was advised that this is cosmetic and the cosmetic portion of my warranty is expired. I think this is a poor grade of stainless steel and should be recalled and/or replaced. I would not recommend.

I purchased a MTW6600TB0 Washer and Dryer on 6/17/07. I have had issues with the washer from the beginning; smell in towels and mechanical problems as well. The machine does not fill properly and receive error codes that are electrical issues per A & E service. I get LF errors occasionally and randomly on different cycles. I finally called for service because I now am receiving F51 Error, which has to do with the basket per A & E service technician. I was told on Black Friday that my machine required both baskets and the rotary motor. My machine is just 4/5 years old. No unusual wear and tear. There are only three people in my family and we live in a fairly warm climate so no heavy winter clothing, etc. I was told that my stainless steel basket was rusting to my plastic basket. I am still trying to comprehend the fact that two materials that are not supposed to rust are rusting. After looking for a new washer over Thanksgiving weekend, I find out that Maytag warranties their stainless steel basket and rotary motors for 10 years. So do they warranty the things they say the warranty or not? Of course, it is a holiday weekend and I cannot get a hold of Maytag. I paid for a service call and the technician told me I would be responsible for the repairs at about $500 for parts plus labor. I looked up the parts he recommended replacing and it was over $800. I paid $1000 for this machine less than 5 years ago. Thats $200 a year for the privilege to use a Maytag. Additionally, my set is black. I can not find a black washer anywhere.

2 weeks after my warranty is up, the control panel is shot. They used to make quality products and that is why I purchased a Maytag. I had before this a very cheap dishwasher from G.E. and it lasted 9 yrs. I cant believe it is already broken. Do not buy Maytag!!

I purchased a range 5 months ago. It is STAINLESS STEEL. It began to rust. I called customer service and they told me it was cosmetic, so they wont help. I think a stainless steel range should not rust after 5 months. Very disappointed, WILL NEVER BUY MAYTAG Again.

March 31, 2013 a Maytag front loader washer series 2000 was purchased. In January an error code E4 and F3 kept stopping the washer. Service replaced some minor part, worked for a week. Then service replaced a circuit board - worked fine for a few months. About June of 2014 the codes came up again. This time Service wants 430.00 for a 700.00 dollar washer to fix a continuing issue. So I decided not to spend the money. I could buy another washer, different brand of course, and try and fix it myself. I removed the top and the bottom front covers. The 3 wires going into the circuit board that was replaced were loose, barely plugged in. The catch all at the very bottom right had derbies and coin in it, cleaned that out. Looked at the motherboard with a magnifying glass. It had no bad solders, cracks or burn marks, so I proceeded to run my hands around the entire drum inside... and in the back side where you can’t really see were some more loose wires.... tightened them. Now with the spin rpms you can understand how things shake loose, I always look for the common sense issues.... I am currently on my third wash load. It runs smoother and quieter than it did when it was first installed. Point is the Maytag service sucks and with only a year warranty from the manufacturer. What did I have to lose to try and fix it myself. I am sure this is happening with a lot of other people. The odds of a motherboard or a circuit board going bad in such a short time made no sense. So check all the wiring FIRST. Make sure everything is securely plugged in. I would not recommend anyone buy a Maytag or Whirlpool (owns Maytag) for their reliability or service.

Further down on this page is my complaint about the dishwasher. This complaint is about the company. This will demonstrate how cheap Maytag is. I filed a copy of my complaint below with the BBB, who in turn forwarded it to Maytag. They sent me a form with rules that they call Dishwasher Recall. Maytag will send me a $250 Prepaid MasterCard, providing that I: 1. Remove the old dishwasher myself. 2. Destroy the machine and/or render it inoperable. 3. Sign and date under PROOF OF DESTRUCTION AFFIRMATION that I have complied. Statement on the form (Your signature is your confirmation that you have complied). 4. Purchase a stainless steel machine (over $700). They list models you should buy. 5. Record on the form; Model Number, Serial Number, Purchase Price, Store where purchased, and Date purchased. 6. Send the signed Rebate Form back along with the sales slip. (Sales slip must show clearly Purchase Date, Purchase Price and Retailer Name). 7. Allow 6 to 8 weeks from the time the Rebate form is mailed. Are they kidding?! If I were to buy a machine at Home Depot, they will deliver, install and remove the old machine. I dont think I would take a Maytag dishwasher for free.

I purchased a Maytag dishwasher (Model No. MDB8949SBWO) in September of 2013. Within the first year (and under warranty) the control module failed. The dishwasher is now almost two years old and the second control module has failed. From other postings it is obvious that Maytag has a known defect in their control units. To replace control modules on an annual basis makes this an extremely expensive dishwasher to own.

I purchased a Maytag Washer Bravos Quiet series 300 & a Dryer Bravos Quiet series 400 w/ steam in June 2009 from Lowes. I cant express my dissatisfaction in strong enough language with these products. From the time they were installed there were problems.The Bravos series 300 washer: Quiet? Never. The thing sounds like a huge motor whirring around my laundry room. Several times, a coin got stuck in the motor and created a clanking sound that had to be fixed. Ive never had a washer that allowed coins to enter the motor. I cant close the lid on the washer until the whole unit is dry because of the mold problem. I dont feel the washer really gets clothes clean. When we purchased the unit, the Lowes salesman stressed that we could fit a large bedspread into the oversized tub and get it clean. This didnt turn out to be true. The clothes tangle terribly and the unit is off-balance with any kind of a larger load. Ive been forced to purchase the extended warranty because of the complete & total lack of confidence I have in this awful washer (same goes with the dryer).The Bravos series 400 Dryer: This unit never dries. All the setting that should be used with the sensor never work which causes a huge problem. I start out on a particular setting with a stated time limit say, for instance 45 minutes. 45 minutes later, I look at the dryer and theres 1 hr of time still left to go! The dryer just runs on and on. Ive taken to using only the timed dry and I start out at 1 hr, then check it every 10 minutes or so. This is very hard on the fabrics and has caused the useful life of my clothes to be greatly diminished. Also, the stupid thing will start to beep and I cant figure out why. Using this dryer has increased the electricity costs to us.I cant stress enough to STAY away from these products. I purchased Maytag because of their prior good reputation. That reputation is in tatters now. They should recall this product and replace it with products that actually do what they advertise!

Purchased this machine (Maytag Bravo Washer) in May, 2015. Drive motor blew Jan, 2017. 18 mo. old. 10 year parts warranty and a tag on the machine that reads MCT (Maytag commercial Technology), which leads the consumer to believe this heavy duty machine. I called the warranty number, as I had properly registered the machine on the day of install. Said he would have a new drive motor out to me in 7 to 10 weeks. Yes. WEEKS. Really? I advised the operator that 3 parts stores in my area had the part available, and asked if there wasnt something we could do. He said no they are back ordered. How is it that Maytag cant get their own parts. I purchased the motor for 118.00 and my clothes are now washing again. NICE job Maytag. I suggest finding another company to buy your appliance from. Promises made are not promises kept. DO NOT PURCHASE THIS MACHINE.

The only reason I am giving 2 stars is because I didnt actually spend my hard earned money buying these machines, they came with our house purchase. At first I was excited to have a good quality washer/dryer... Now I understand why the previous owners left them behind. My complaints are like most of the others on here - takes way too long to do a load because of the stupid water sensor, it doesnt wash loads evenly so everything on top hardly gets wet and washed properly, lint all over our clothes, powder residue left behind even though I set it to 2 rinses, a lot of settings but missing useful ones like quick wash... just all around disappointing. At least one good thing has come out of this and we will not be buying Maytag for our new laundry room. Saying that I have also read so many bad/worrying reviews about Samsung and LG - cant any company make good, reliable, lasting products and stand behind a warranty anymore?!

The fridge has a grinding noise that is getting worse, by the day. I cannot seem to define the exact location of problem, whether the freezer or the fridge. Maytag you stink, and your web site stinks, too.

I am fairly happy with this ranges performance. I do have a couple of issues on the design. I would like to be able to simmer at a lower temp on a front burner, as I use a large stock pot and a pressure canner occasionally. The smaller BTU burners are on the back and the large pots do not fit over them. I havent noticed any problems with the upper ovens performance...seems to do what I ask it to, including the broiler. I have not tried the lower oven or the convection feature at all yet. Nor have I had to use the self-cleaning feature, yet...almost afraid to after reading other peoples nightmares, though.My biggest concern is the lack of safety with the knobs on the front of the stove top. Several times, the gas has been turned on by my cat simply walking across the front of the stove and stepping on a knob. This allows gas to leak until I notice. It happened again early this morning just before 4:00 am. I was awakened by a smell, which I thought was a dead mouse somewhere (we live in the country in a 100 year old house - mice do get in, thus the cats). I searched the whole house, looking for a dead mouse, until I finally walked into the kitchen and heard the hissing from the stove. Im glad I didnt try to light a candle while I was still thinking dead mouse!After turning off the gas and removing all of the knobs, I opened all the windows to let the house air out. I SHOULD NOT have to remove the knobs every time my stove is not being used! You do have to depress the knobs slightly to ignite the burners, but its too easy. Obviously, the simple act of a little cat putting its paw on the knob is enough to open the gas. This is a serious flaw that could kill someone! Something needs to be done to correct this before someone is killed or a house full of propane or natural gas is ignited and explodes!!! I will be reporting this to Maytag and hope that they will voluntarily issue a recall to have this problem fixed...Wish me luck.

18 month old range did not shut off although it showed off on the cancel page. $800 down the toilet. Maytag had the guts to charge $100 to troubleshoot plus parts and labor. I will donate it to scrap metal. Company does not give a rats behind. DO NOT BUY MAYTAG.

Purchased the very top of the line Maytag Washer and dryer.. Top loader MVWB955FC1 washer. I got this huge washer and dryer because I was tired of paying $20 to have my Cal King comforter laundered. Bad idea.. Yes the comforter fits easily in the drum of the washer but it does not even come close to clean.. Why no agitator..? It leaves soap all over it in addition to the dirty laundry smell.. The dryer is better but it takes at least 3 cycles of taking it out and un-wadding it to get it all the way dry. Now my wife just hangs it on the line.It has been just over 3 years Feb 2017 since I bought both units from HH Gregg.. Now the top of the washer around the soap dispensing orifice has rust bubbling up worse than my 25 year old unit I put by the curb.. Maytag support is no help.. “Sorry rust is normal and it your unit is out of warranty”. I asked If this would have been covered under warranty.. NO!.. Not unless you report it within 30 days.. We only use it once or twice a week.. What terrible service..

My complaint is not against Home Depot but Maytag Products. They are inferior products. Stay away from Maytag! Note: We are in our mid-to late 60s, no kids using these products and they do not get a lot of wear and tear. Maytag Microwave: MMV 4205DS-0, May 29, 2014 we purchased Maytag appliances for our kitchen (stove and microwave from Home Depot). I liked the 10 year metal warranty plate attached to the front limited warranty of the microwave. This means nothing! They cover the stainless cavity of the microwave (a part that will never go bad). June 3, 2014 this microwave was delivered. Thanksgiving, the microwave went out November 30, 2015 this was replaced with GE Profile Model JVM3160RFSS for $178. November 30, 2015, Diamond Factory Service was here for the Microwave. We paid $90 for the service call. They wanted $228.09 to repair (1-8206419 Switch $15.22; 1 W10269460 Switch $27.03; 1 W10727360 Microswitch $27.03 and Labor $155.00). Maytag Dishwasher MDB7749AWM. Purchased from Al race Appliance for $599.95 total with tag etc was $920.27 on 5/16/12. So thankful was purchased the additional warranty for five years. We have had 2 service calls so far for the same issue, which is W10356494 Console CMFF0312434. This is a known problem (it will not start). I wish I would have googled the model before purchase was made. When the warranty expires, this will go to the curb too.Also, purchased Maytag Neptune Washer and Dryer from Best Maytag, Rockford. The dryer had problems with the circuit board after a short time. Too expensive to replace. Our family and friends ALWAYS purchased Maytag only. No more! Stay away! We are waiting for the oven to go next. Oh and check out the bottom drawer. There use to be room for pots and pans. No more. Lucky to get your pot holders in there.

Oven is not even 2 yrs old but, the bottom oven floor lining is crackled & flaking. Although they say the cavity is covered under the 10 yr warranty, they say its not covered. Basically told me theres nothing they can do for it. I bought all Maytag appliances for my new home because they claim they stand behind their product. The 10 yr plaques on the appliances are a joke. So disappoint.

I purchased a Maytag Bravos XL Commercial Technology top loading washer, model # MVWB850YWO, in May 2012 and it was delivered in August 2012 due to a home purchase not being consummated. Anyway, I bought this washer and the matching dryer at Lowes and purchased a 4 year extended warranty with Lowes. This would cover me with a warranty through August 2017. I had some problems with the washer while under warranty and had it repaired at least twice. I have had, and still do, have a water leakage in the washer. The water when dispensing into the detergent compartment splashes over and you would think it would just go into the tub. Someway the water leaks down the inside of the washer and runs out onto the floor also causing rust to the inside of the front panel. The resolution was to turn the water pressure down on the supply lines. When this was done, the washer would quit running due to not enough water being dispersed into the drum. A replacement seal was installed and I still have the same problem. The repairmans final resolution was to put tape over half of the detergent dispenser to hold the water in the detergent dispenser and still allow me to put detergent in the dispenser. So, a towel is in front of the washer to soak up any leakage. Now, just 5 months after the extended warranty expired, the bearings under the wash tub are starting to roar during the spin cycle. I contacted Lowes service again and basically I am out of luck. The repair cost is expensive, the part and requires 2-3 hours of labor. I decided to chuck this washer and buy a new one. My wife found one that has an agitator, unfortunately another Maytag, and wants it as she has said the Bravos washer never seemed to get the clothes clean (due to not having an agitator). When checking online for references on a new washer and any recalls on my current washer, I discovered other Bravos XL owners having the same problem with the bearings in the tub. I contacted a local business to try and sell it to him for cheap and when I told him what was wrong with my washer his reply was, I have one just like it out back with the same problem. Dont need two problems. Cant even get rid of a Maytag washer due to it being junk. Many other reviews have listed problems with Maytag products especially since Whirlpool bought them. The Maytags of today are not your parents Maytag. Used to be the Maytag repairman sat around his office waiting for repair calls. This has changed considerably since Maytag sold out to Whirlpool. After doing some research, it seems Whirlpool has bought just about every company selling washers and dryers and are making them as a disposable item. I would advise not purchasing any product that is under the Whirlpool corporate umbrella as I feel whatever they buy, even a superior product like Maytag, they cheapen the product and try to benefit from the name, as in the case with Maytag. So, no more Maytag or Whirlpool products for me until they have proven they can build a quality product once again. Hello GE!!!!

The washer does not clean clothes. Thank goodness I bought a 4-year warranty because they have been out 4 or 5 times on washer alone. The dryer is now squealing and shuts off (a safety feature I am sure). The repair person replaced the pulley system and one belt, it still squeals and shuts off. I called the Maytag CEOs office and talked to a machine. Some really nice lady called me back and said she cannot do anything to help me. They have no consumer person to help you and troubleshoot with you. The washer is rusting, it is an inside washer. I live in SE, Texas and they told me it was due to living close to the coast. Well, Ive had GEs that never rusted and in fact, the problem is really with all the HE washers. I hate them. They do not clean clothes. I will never buy another Maytag or Whirlpool product again.

Purchased the Neptune washer & dryer in 2002. Did not purchase any additional warranty. I have had Frigidaire, Kenmore and Speed Queen washers previously and used them until they quit. I have not had any problems with either the washer or dryer. No mold, no smell, nothing. I did laundry for 2 children and 2 adults, 6 to 8 loads per week with half being heavily soiled work clothes. I still wash 3-4 times a week. I was able to wash & dry king size blankets and comforters for the first time with this set. Washer and dryer are located on the main floor of house and are the quietest units I have ever owned. They may quit tomorrow, but they have done the job that they were designed to do. I am well satisfied with the quality and performance of both units and would not hesitate to purchase Maytag appliances again.

I bought a Maytag dishwasher in 2019 in Home Depot for my new home. The dishwasher stopped washing dishes after two years and 6 months. The price of the new machine was 700$ and I did not buy the extended warranty. The trouble is circulation pump, that cost to install the new one from local service would be about 350$ plus the new pump 150$. I consider quality is very poor if the new dishwasher works only two years and then it is better to buy a new item than fix the old one. Never never buy Maytag production.

Purchased washer in Nov. 2014. Remodeled house. Moved in on May 2 2015. This washer failed in just 3 washes. Pump froze up. Now it is august 5 2015 washer did it again. Model MVWC200BW. It appears this will be the 3rd pump. There seems to be something here. If it stays together in order to keep this washer I have to buy extended warranty. THESE PUMPS COST 100.00 PLUS INSTALLATION. MAYTAG dont seem to see this as a problem but as a consumer it is very well a problem. I am a electrician by trade and deal with pumps and motors ac/dc. This is a problem.

This washer is no better than a glorified garbage can. Maytag AKA Whirlpool should be ashamed to put their name on this product. Like others before me on this website my washing machine sounds like a jet is taking off in my basement. When I contacted a serviceman, he told me the drum seal is broken and the bearings are shot. I have the machine since April 11, 2011. Not even three years to date! I do not have an extended warranty so shame on me to believe that a 900.00 machine should last well beyond 3 years. Unfortunately, I am getting the run around from Whirlpool as all of you have experienced. This is criminal. Not only are we as consumers being defrauded by irresponsible manufacturing but these huge hunks of metal and plastic are polluting our environment. Our parents had washing machines and dryers for as long as 20 to 25 years and they actually cleaned clothes. We now have high efficiency machines that destroy our clothing and leave them dirty and wrinkled. They are now made to break in 5 years and from what I see on this website the average for breakdown is becoming 3 years. Do you think that this is not by design? The service call turns out to be more than the value of the machine, so the repairman doesnt even profit as consumers refrain from costly repair and repurchase. The only profitability is gained by the manufacturers that keep pushing out junk to the consumer. These manufacturers should be accountable like the American auto-manufacturers became accountable for the junk they manufactured at the expense of a whole city, Detroit.

I bought my Maytag dishwasher on September 4, 2013. In August 2014 the control panel went out. (Sound familiar?) The dishwasher was still under warranty, so I called Maytag. It took 3 tries to find a repair person who would come out on my schedule. (Im a teacher and cant take time off.) They installed the new control panel, and it working. I tried to submit a review on Maytags website, but my review was denied. I guess they didnt want to hear the truth.

Updated on 08/13/2021: Today a repairman who is authorized by Maytag came out. He found the problem, some arm that popped out that is located underneath the washer. He put it back together and said he needs to order the part and it will take 30 more days. Set the washer so that it SHOULD work for a couple of loads. I spent $700 on a washing machine and I have to go to a laundry mat to get my clothes washed. Here is the clincher. The guy left no paperwork, nothing, not even a business card. So I am at the mercy of this repairman (I think he said his name was Jessie). The guy was friendly, quick and knowledgeable, however he told my husband he knew what the problem was going to be, if you knew why didnt you bring the part with you and he said the part is out of stock. Why, is this part unique to Maytag washers? So I am still waiting for my washer to be fixed.Original Review: In December 2020 I purchased a Maytag washer it was delivered in January 2021 and it worked great for the first several months. Then the machine started making noises, clicking noises like it couldnt move through the gears. Then I started noticing that my clothes were not getting cleaned. It was taking an hour to wash the clothes. I told my husband it is not agitating just clicking. We had to stop and start back up the washer just to get the water level high enough for the so called deep water wash. I was finding residue left on my clothes and had to wash them 2 or 3 times to get the clothes clean enough to wear. Sometimes it wont spin enough to empty the water in the tub. It smells almost like wire burning. It has barely been 6 months and I have to have a repairman out. I will review the washer again after it has been fixed or replaced. But as of right now I will never buy another Maytag again.

Like most people with this Bravos machine, I am 3 months out of warranty and the ball bearing is trash. When the wash goes into spin cycle, it makes a loud clicking noise and takes a few minutes to start spinning. I called service repair and he told me that it was the ball bearing and to talk with them as he has dealt with quite a few high end machines from Maytag that are breaking down after warranty. I should have realized there was a problem when we kept coming up with white spots on our clean laundry and would have to re-rinse clean clothes. This kind of defeats the water saver that is advertised with the machine.Do not buy this product. For a high end washer and dryer, there are many problems. Maybe that is why the Maytag guy is not shown sleeping in commercials any longer. Hes too busy fixing all these machines. Btw, they wont cover the part even though I offered to pay for the service. The best they can do is give me 25% off. Yippee! I cant wait for the other problems to hit me like everyone else.

Bought the washer in February 2012 for $900 at a local appliance store, delivery included. Just yesterday (10/16/15) a 5 cent piece of grey plastic flew out of the lid lock mechanism. Thinking this $900 modern piece of machinery painstakingly designed by intelligent people with university degrees would certainly work if I just stuck the plastic part back in. I just popped it back in, the lid locked, and the machine spun away happily (only having to run a correct cycle for an unbalanced load twice! What joy!) Fast forward 40 minutes, I skip down the stairs to go retrieve my flannel sheets (because its October in Pennsylvania, its getting freezing cold at night) and pull up gently to open the lid. It doesnt budge. About 2 hours later, following a screaming match and some furious googling, it was determined we would need two people to pop the entire top off the machine to extract my sheets.So in order to use the washer to clean clothing now, weve been unplugging the machine. Removing the three screws on the control panel (aka brainbox), unplugging the black and white wire from the brain box, taking the control panel off and sitting it on the dryer, and using putty knives to push in the metal clips holding down the top of the machine down, and prying the entire top of the machine back on its hinge. Then I can get my clothes out. Then doing so in reverse (dont forget to add detergent before shutting the lid! It will lock and you will have to pop the entire top off again.) to use the washer. All because of a 5 cent piece of PLASTIC. What brainchild figured, Eh, we can just use plastic for this important piece that the washer wont run properly without. It doesnt matter!? Someone that wanted to make $300 a pop doing service calls thats who.I cant believe Maytag has gone so far down the tubes. In case anyone else ran into this problem and needs to fix it, write down the model number, serial number, and other crud listed under the lid. Then use them to wipe while youre in the bathroom. All you need is the company and part number on the lid lock mechanism. According to Maytags website my washer doesnt exist. And there was no way, no matter how creatively I googled, to find a part for it with the Maytag model number. So now I have to try to find this measly mechanism to replace and try to use this piece of crud for a few more months. I guess my Christmas present this year is buying a new washer. And you can BET it will not be a Maytag.And two more things: with no agitator, you can fit really big stuff, but you also get to hear your washing machine dancing on your basement floor with an uneven load. No matter how many times you try to re-position items, it runs a corrective cycle, refills with water, and spins everything into a ball AGAIN. Also, the miserable thing is starting to rust. Right on the sides and near the lid hinge, and all around the bleach receptacle. How cheap, a washer on which the paint rusts right off with chlorine bleach.I wish I still had my Grandpas old 1930s wringer Maytag. At least I knew that one would work without a cheap piece of plastic. And at this point I might prefer wringing my clothes to hearing my washer try to escape. In short: cheap parts, no replacements available through company for DIY repairmen, company designed to force customers to use their servicing for $300 a pop. 1/10 would NOT recommend Maytag.