Three years ago, we purchased a gas Maytag double oven, it worked fine for three years, then it blew the breaker. When we turned the power back on, we could not turn the oven off. The control panel had to be replaced, dinner too. We had bought the extended warranty, so that was covered. Last week, after four months, it happened again. We placed an oven thermometer inside the oven and it is was higher than the maximum temperature of 600 which the thermometer could measure. We are currently awaiting a new control panel. Maytag used to be a good name, but recommend you to buy something else.

Bought a stove in May of 2014. In July of 2014 we noticed a 1x6 stain inside the glass of the oven door. I called Maytag and they stated only 30 day warranty on cosmetic flaws. I said this was not there when we bought it. They asked if anything had boiled over because if liquids get in the vents on the oven door it can get in between the glass. I stated no, only cleaned with Stainless steel clear. They stated most likely when I sprayed the door it ran down in between the glass. I said that is a flaw. They said, no the vents are there to allow heat out. I asked if they also were designed to let liquids inside the glass, they said no, I said design flaw. They will do nothing. I also pointed out that nowhere in the owners manual is there a reference to this possibly happening. Our sons in laws have a 3 year old LG stainless steel with vents and have never had this problem. Maytag will not stand behind their products even when they are the ones at fault. Buy a different brand.

I have a Maytag Range that I bought new and installed 6-1/2 yrs ago for over $1200.00. I am single so I rarely use the ovens. The upper over I use maybe 1-2 times a month and the lower oven I may use once a month. The night of 3/7/2016, I used the cleaning cycle set on medium for both ovens. Yesterday, when I went to wipe the ovens down, I found the lower heating elements, on both ovens, had snapped. The top ovens lower bracket had broken in 2 places, the first break is about 2 from the connection, on the right side leaving about an 7 gap. The lower ovens element had broken in only one place about 2 from where it connects into the back of the oven. This has to be a flaw in the either the design or the material. In the 45 yrs that I have been using ovens and stoves, my last stove was over 35 yrs. old, I have never had a heating element break. While I can understand a break at the connection, I can see no reason that the it would break in the center of one side on both lower elements in the same oven. I also noticed that lower heating elements are a much small gauge than the top which I find strange.The other issue with the stove is the seals around the windows are not tight. I noticed dust was inside the two glass panes. The rubber seals were sunk down into the door, but Maytag said it was not their problem that I must have done something. When I remodeled my kitchen, I bought all Maytag products: 1.H20 Frig - The electronic panel went out after 3 months and had to be replaced. Manufacturing Defect - When the repairmen came to fix it, he told me to call Maytag which I did. They refused to pay for the repair because I called a repairman first, even though the business was Maytag certified. Even though I said I would cancel the service call they said because I had made the appt. and they recommended I call Maytag, they would not cover the repair. 2. Stainless Steel Dishwasher (Cost over $700.00) - Motor went out after 3 yrs. 3. Microwave/Convection Oven (above the stove)- Convection light out after 4 months. The replacements are not inexpensive.One other complaint I have is when I bought all my large kitchen appliance Maytag had a $600.00 rebate offer. Even though I mailed all the required documents to the company over 2 months before the rebate ended, I never received my rebate. The explanation I received was that the center that received my documents delayed forwarding them to the proper department that processed rebates and they were received after the offer ended. When I questioned the legality of the practice, I was told that this was all explained in the Terms and Conditions (ie: small print).

Bought a nice looking Maytag fridge 2 years ago. For the past 6 months it has been leaking all over the kitchen floor. Most recently it has started leaking every 2 days. It is so frustrating as well as extremely dangerous! Both my younger kids have slipped and fell because of the slippery floor. We now have to keep a towel there all the time.Please let me know if there is a product recall. Not the Maytag we used to have. My parents bought all their Maytag appliances when they got married and they lasted over 30 years! This is why I bought the Maytag fridge... not sure of the quality now.

I have a Maytag Series 3000 washing machine which, as many knows, is the same as a Kenmore. I bought the set 23 months ago and since then, I have had nothing but trouble. In my first three months of ownership, I had my first error code of which I had to replace the hot/cold water valve. Fortunately, the unit was under warranty. Since then, I have had to replace the CCU and MCU twice. Now, the units MCU went out again! Whatever happened to the Maytag name? How can I get this permanently fixed or replaced? Is there a lemon law for appliances? Any assistance would be appreciated.

Dont ever buy this washing machine. After warranty was up, the motherboard went. After that, the pump went. Now, the machine has been shaking and we have to realign the clothes in the washer on an average of 6 times before it completes the cycle. The banging is nerve-racking! Never again buying Maytag!

I purchased two high end Maytag machines, one washer and one dryer, approximately 36 months ago. I did not buy the extended warranty because I was foolishly convinced Maytag sold reliable products. The dryer required service twice within the first 18 months. The washer, which is computerized, is almost unusable. The sensors dont work properly. It does not spin without continual restarting the machine. It takes me hours to wash one load of laundry, and even then it is not spun properly. I wrote Maytag headquarters twice via e-mail, with no response. Even though their website says someone will get back to you within three business days. I called Maytag on August 12th and was told there is nothing they can do because I didnt purchase the extended warranty. So the bottom line is you can spend thousands of dollars on their machines but dont expect them to last, or work. And Maytag will not stand behind their products.

My refrigerator was delivered on April 3, 2016. I began calling for service July 2 when the bottom freezer door started depositing ice chunks on my kitchen floor every time we opened it. An appointment for service was made for July 18, service never showed up. Another appointment for August 3 was made and again service never came. I called the 800 number on Aug 19 again arranged service for Aug 24 after hours so that we did not have to take anymore time off work. When repair finally looked at the fridge they said the door was not aligned and did not close so the frost builds up and breaks off onto the floor. This can be fixed with a new door that can take from 6 weeks to 8 months as they are not stocked and have to be made at a factory. The fridge constantly runs and is starting to leak water through to my kitchen floor and basement ceiling tiles.I called Maytag/Whirlpool on Aug 25 and the service agent told me the best they could do for me was extend my original warrant by 6 months while I wait for replacement part and they advised I purchase the extended warranty. The second agent named Gabby I spoke to advised me to call Home Depot where I purchased the fridge to see if they would do something for me. She would write down my concerns but had nothing more to say or do for me since the repair person deemed the unit repairable and a part has been ordered. I called Home Depot on Aug 25 and I spoke to Appliance Dept who told me the manager who could help me was off that day. He advised me to stick weather stripping around the door to seal the leaks. I said I was hesitant to do anything that may void a warranty and he agreed. He suggested I may get a loaner fridge but I have heard nothing yet. I want a replacement fridge.When you pay $2000 for a fridge it should be worry free for at least a year? I have been reading reviews and I am wondering why this is not a recalled appliance as this seems to be a very common problem. I am sad that Whirlpool is not standing behind this product. Home Depot has been in touch with me regarding this fridge issue and the lack of customer service provided by Maytag. They are replacing the fridge on Sept 9th 2016 and taking the old unit away. Home Depot has tried to get in touch with Maytag and they have not gotten a response at all about my faulty unit.The staff at Home Depot in Peterborough have been excellent to speak to and have apologized for the issues with getting service to my appliance. I am very grateful to them for their assistance and for following up with me in this matter. The downside is that I am getting another exact Maytag unit as a replacement so hopefully this does not start all over again. Home Depot has been a great retailer to deal with. I am very saddened to hear that even Home Depot cannot get responses from this manufacturer. I have also lodged a complaint with the Better Business Bureau.

I have used several brands of refrigerators and Maytag stood out for me. Everything works as good as new. However, my experience with ice machines, has been the first thing to quit.

I purchased a Maytag Dishwasher in April of 2011 - Ive had four control panels in that time and the panel gone again - in fact, one panel came out of the box nonfunctional (I counted that one as it was installed although the tech removed it when it quickly became apparently that it wasnt working). Ive got a complaint in to Maytag but I have low expectations as to a satisfactory conclusion. What Id like is for Maytag to buy this lemon back from me for around $400 - I paid nearly $600 (including installation). Again, I doubt this will happen. From my research online it appears that the control panel issue is a latent defect which Maytag knows about but either wont or cant figure out how to deal with it or correct it. I have a scan of the receipt which Ill see if I can upload later. I know about one class action lawsuit for CA residents. I wonder if its been expanded.

What happened to the days of buying a washer/dryer and having them for years! To spend a thousand on each and have holes in the bellow causing dirty water to Empty on your floor. Not once replaced, not twice, 5 times!!! Now Im looking to buy another. Old school for me...

We purchased a Maytag brand thinking it would be a quality long lasting machine. Wrong, the washer shakes from day one, We complained to Lowes, they brought out and installed a second unit, it does the same. The clothes dont get clean, sometimes you can see the blue HE Tide still on the clothes (sheets) after cycle is complete. Junk, waste of money, Ill never buy another Maytag product again. Dont waste your money on a Bravos Maytag top loading HE machine.

#Mgt8885x500 Maytag Gemini. After oven heats up, racks fall. What should I do. This is a safety issue. Help, afraid to use oven.

Just replaced a washer that lasted over 7 years thru 3 renters with the Bravos top loading washer. There is nothing efficient about a cycle to take 73 mins to wash 20 articles of clothing (t-shirts, socks and underwear). The machine dont wash the top of the load. Also the deep clean feature isnt deep cleaning. I recorded a video of 20 mins of the machine not washing properly before going into rinse cycle. If this item dont produce refunds of the amount of water wasted RE-WASHING and electricity because it doesnt clean on first wash, then its time for Maytag to pay my utilities. For the money spent on the machine, going to the laundromat every other week with 1 roll of quarters each trip comes to be I can wash for 4 years and will outlast the longevity of the machine before it breaks! Also bulky mode is how you get more water in the machine but will take 63 mins to wash.

Theres nothing at all good about this machine. It is impossible to work with. Ive hated it since the day I got it. Dont buy it, ever, ever, ever. You cant put additional items in once its started, you cant adjust a load thats uneven and get it to complete a cycle, it takes forever to do one wash and it often rinses multiple times and theres no way to stop it. I HATE THIS MACHINE. HATE IT. LIKE ITS A PERSON. HATE. Is that clear enough?

We are a family of nine so I wash a lot of laundry. We bought this washing machine a month ago and hoped it would perform like our prior one. The problems are many. It is too smart for its own good- it requires a cleaning after every 30 washes but gives you zero warning beforehand so you will already have the clothes in and started the cycle when it will stop the cycle saying it needs cleaned. There is nothing you can do to override the cleaning cycle, so you are forced to remove your sopping wet clothes and run the cleaning cycle- wasting time and money on precious water! It also wants you to use its specialty affresh to clean it with, adding cost we hadnt planned on. Then you cant tell when to put the clothes in as it tells you to start the washer and then add the clothes, but if you put the clothes in first sometimes it wont start because it wont sense properly, and if you start it without the clothes. Then when you stop to add the clothes it wont start it with the clothes in it- which way does the machine want it?! So it is a guessing game as if the washing cycle will even start. And the washer wont hold as many clothes as our last one did. If there are too many clothes, the cycle will stop and it will refuse to wash until some are removed. Whenever there is a problem starting, which in one month has been four times now for us, it is a huge guessing game as to what is wrong for why it wont start. I dont need this kind of frustration! Further, the locking mechanism in the washer is plastic, and I know from experience that plastic parts will be the first to break. Had I realized this before purchasing, I would have looked for a metal locking device. My guess is when it does break, the whole washer will break. Also, from day one, it has made a sound that Im not sure is normal. It sounds almost like grinding gears every time each various phase starts or stops (washing, rinsing, draining, etc.). I sincerely hope this isnt a manufacturer defect as we didnt buy the extended warranty. We researched this model before buying and many were happy with it but I hate this washer! I loved my last Samsung washer but it rusted all over after just five and a half years even though it still worked great, so I didnt want to buy Samsung again so we took a chance with this Maytag. I am regretting this purchase. I consider myself to be a person easy to please. I want a washer that works that wont rust that you can put a ton of clothes in and throw it in the wash and forget about it. I dont want all this high-tech sensing stuff that just messes up and is highly inaccurate in what it senses! Why cant companies offer a simple, high quality product anymore that works, without the added costly features?! The model number is: MVW6230HW0. Avoid this model number.

I purchase the Maytag dishwasher Model: MDB7749SBM from Home Depot in Plano Tx around June of 2013. The start/resume and cancel/drain button lights either flash or wont turn off and keeps trying to restart the wash cycle. I have only had this DW for 1 1/2 years. That’s pathetic! I went through the manual and tried everything it recommended but it didnt work. So far the unit still cleans dishes. Based on all the reviews I have seen on these Maytag dishwashers with the same issue, you would think there would be a recall. All the appliances in my home are Maytags and Whirlpools. Maytag and Whirlpool are now the same company. Depending on how they handle this issue will determine which appliances I buy in the future.

I owned a Maytag Bravos top loading washer for 8 years, and I loved it. It caught on fire while washing a load. Thank God I was home or it could have burned my house down. Just wanted to post this somewhere to issue a warning.

WORST MACHINE EVER! Besides the soap scum Maytag Bravos XL Washer leaves on all of our jeans and my husbands work pants, the machine decides when it wants to work and when it does not want to work. Weve had repairmen over, we have called the 800 numbers, just like all of the other reviews on here. Ive readjusted clothes in that thing more than Ive done laundry in my life!!! I HATE this machine. Ive memorized the manual from reading it so many times, have the correct detergents, tried washing large loads, small loads, lined up the clothes around the outside so the middle thingie is not covered, thrown clothes loosely in there. Every way possible. The machine senses, starts filling, then just stops. Today, no matter what I do with the load in there, it will NOT run, it keeps shutting itself down and I do not even know what else to do. NEVER EVER EVER buy this machine! We will never own another Maytag EVER.

I purchased a new Maytag from Home Depot. It was delivered and installed by them on 7/20/12. Today is 9/18/12. It is less than 2 months old and the tub is starting to shred around the upper rim. I called to get it repaired. What a nightmare. First I tried to understand a Filipino woman through a bad connection. She advised me to call a different customer service number, 1-800-688-9900. I talked to Crystal. She called up information on me using my phone number. She asked for the serial number as she had the model number available from the online registration I completed on 7/20/12. I told her I do not have that and asked where it was located. I also told her that I was unable to get it at this time as I am handicapped. She advised me that I had to show my repairman the receipt or I would have to pay a $60 service charge. I get nervous about throwing good money after bad. So I then asked why. If the serial number is so important, why is it not a required info when you register online? She had no answer. I asked to speak to her supervisor. I waited 4 minutes. Enna finally came on the line. She gave conflicting info about my online registration. She said I was not registered online (if not, how did Crystal have all my other info including my model number? Why did Crystal tell me I had registered without the serial number?). Enna told me that the repairman could key in the serial number when he gets to my house and if my washer was under warranty, I would not be charged. Again I asked why, if the serial number is so critical to the process and with all the info they seem to have on me (name, address, phone number, model number, place of purchase, date of delivery, etc.), why is the location of this very critical number is not in the owners manual? Why do they allow you to register without it online and why dont they track sales and delivery by serial number? She was unable to address these issues. I asked to speak to her supervisor. She told me she would give me her supervisors name and number (Kim, **) but she would not give me a last name or contact information. She told me that she was the highest level that I was allowed to speak with.Bottom line, my Maytag is falling apart, getting through the red tape to get it fixed under warranty is silly. Maytag ignores its own concept of tracking by serial number and does not support the use of serial number by telling you where it is located on an appliance or requiring it to register online. Calling customer service is a joke! I was mad when my new $800 washer started to fall apart. Now I am just sad with the way we allow manufacturers to treat us. Mad about the way we allow them to operate in the United States. They create junk or junk parts overseas, products fall apart over here, calls for repair get routed around the world, and then they create more red tape and call it customer service. I made one bad choice. Hopefully, you are reading this and can avoid your own.

We purchased this washer (MHW05500FWD) and dryer set in 09/26/2016 and have had nothing but issues. I have had the repairmen out twice. The first time the washer wasnt rinsing out clothes, when the repairman came out he couldnt find anything. In June of 2017 the same thing happen. Once again the repairman came out. I found out that there was a recall on the part which was on Backordered. Now the matching dryer model MED5500FWD is not drying. This is the worst washer and dryer I have ever own. I will NEVER own another front loader again. Buyer Beware!!!

I bought a Maytag dishwasher (MDB7749SBM) and 1 yr and 4 months the control panel went out and all Maytag would do is tell me that they will pay for the parts, and I have to pay for the labor. I remember when Maytag had the best Warranty on their appliances. I am very disappointing with paying for labor. They also offer an extended plan of $269.00 for a year. What a joke!!!

Purchased the Maytag Bravo Nov 2010 and had to replace it after just 5 years. In the five years we owned it, it required a new water pump and the stabilizers had to be repaired. Its motor burned up and I was not able to find a replacement. I was quoted $224 (parts only) for a replacement motor and 10 weeks delivery. My wife never liked the machine as it was not able to clean clothes that well. We did not find much difference in any of the settings. We tended to put very few clothes in each load in order to get them clean. We were dissatisfied that it did not have a soak cycle and the lid lock was particularly annoying.

I read the reviews before I bought this washer, went to a major department store to buy it. This way I knew that I could get good support if something happened to it. Its been 3 months, I use the washer everyday. There are 4 adults in my building, they use it daily. I have never had a problem yet, the clothes come out cleaner than the front loader I have. It seems Maytag still makes a good product. I am the first to admit, when you make large number of products you will have some with a defect. But this washer the Centennial by Maytag works great.. Plenty of water in the tub, the clothes come out clean.. Maybe those people having problems need to stop buy at big box home centers. Theyre known for lumber not washers.

This is a wonderful washing machine. For cleaning clothes it does exactly what you expect from a washer. We have had 2 Neptune front loaders. They, however, have a couple flaws I dont want to live with again and will be looking for one that has come up with the solution to them. One, the bearings on them need replaced on a periodic basis or it sounds like a 747 taking off. Two - the front gasket around the barrel has a mold problem no matter how much you try to keep the thing clean. Other than that, these machines perform fantastic.

I have a Maytag Centennial washer & dryer put into service in August 2011. The washer has recently gotten quite noisy, so I had a repairman out to look at it. He found that the bearings are going out & estimated repair costs at $360. He actually did not recommend repair, as the repair costs approach half the price of a new washer. I am very angry about this, as this is quite a new washer & was not a cheap model. There are only 2 of us in the house, so I only wash an average of half a dozen loads a week. I never jam the tub full, basically baby the washer so it will last. Much good that has done! Im old enough to remember when Maytag was the best in laundry appliances, expected to last for many years. I bought the Maytag because my last (top-of-the-line) Whirlpool set required a number of repairs, not realizing that Whirlpool had purchased Maytag. I will be using this washer until the bearing seize & then I will be buying a non-Whirlpool product Im afraid that will mean a foreign brand. I really prefer to buy American, but apparently, thanks to Whirlpool, that is no longer possible!

First of all, the hoses that came with my washer leaked and were cheap made. My husband put the hoses from my old washing machine on the Maytag. Then, I hadnt had my Maytag washing machine but about two months when I had a problem with the mixer. I had to turn the hot water connection off in order to wash in cold water. When I called the store to explain the situation and ask if they had their own serviceman, the person I talked to made me feel like a complete idiot. He said in his twenty something years of selling Maytags, he had never heard of such a thing. Anyway, when a serviceman finally came, he also had to replace another part due to a recall. Now, my washer is right at four years old and is leaking from under it. My husband checked the hoses, and they are not the problem. I bought a Maytag thinking I was buying the top of the line but I guess I was wrong. I will not buy another one nor recommend them.

Updated on 08/13/2021: Today a repairman who is authorized by Maytag came out. He found the problem, some arm that popped out that is located underneath the washer. He put it back together and said he needs to order the part and it will take 30 more days. Set the washer so that it SHOULD work for a couple of loads. I spent $700 on a washing machine and I have to go to a laundry mat to get my clothes washed. Here is the clincher. The guy left no paperwork, nothing, not even a business card. So I am at the mercy of this repairman (I think he said his name was Jessie). The guy was friendly, quick and knowledgeable, however he told my husband he knew what the problem was going to be, if you knew why didnt you bring the part with you and he said the part is out of stock. Why, is this part unique to Maytag washers? So I am still waiting for my washer to be fixed.Original Review: In December 2020 I purchased a Maytag washer it was delivered in January 2021 and it worked great for the first several months. Then the machine started making noises, clicking noises like it couldnt move through the gears. Then I started noticing that my clothes were not getting cleaned. It was taking an hour to wash the clothes. I told my husband it is not agitating just clicking. We had to stop and start back up the washer just to get the water level high enough for the so called deep water wash. I was finding residue left on my clothes and had to wash them 2 or 3 times to get the clothes clean enough to wear. Sometimes it wont spin enough to empty the water in the tub. It smells almost like wire burning. It has barely been 6 months and I have to have a repairman out. I will review the washer again after it has been fixed or replaced. But as of right now I will never buy another Maytag again.

The control panel died on this dishwasher (MDB7749) after only 2.5 years of light use. I was quoted about $250.00 plus labor to have the panel replaced. I will not fork over several hundred dollars for a defective panel, especially since many others have complained about repeated failures and known issues with the control panel. No more Maytag products for me. I plan to purchase a Bosch to replace it.

It seems to be a broken record with other reviews. I had a 2 year old microwave and the door doesnt recognize that its closed. Which means it wont turn on when I close the door. So you have to open and close it maybe 30-50 times and sometimes it works. I call Maytag who schedules a company but doesnt disclose anything about the warranty or service cost. I was thinking it would be a nominal fee since it falls under a 10 year warranty. The company calls and confirms the cost and I recheck with Maytag who said that the warranty only covers parts. So I buy a $300 microwave and have to pay $160 for a service visit because your company made inferior parts. Absolute sham of a company. Buyer Beware...

I purchased a Maytag quiet series dishwasher (Model Number: MDB6759AWW) for $500.00 in May 2009. Three months later, I started experiencing difficulty with the control panel. One light would continue to blink and it would not do anything else. I called to have it repaired but by the time he was to come out, it started working again only to stop working again the next week. On 7 Oct 09, the repairman came out and replaced the panel. Then, about six months later, it stopped working again. I called again but canceled the appointment because it started working again. Then, after having it for one year, it stopped working again and I called only to be told that it was no longer under warranty. Now, we cant get the control panel to do anything. From all the other similar complaints I have read, it seems like there is a defect with the control panel. A dishwasher should last for more than one to two years. This is very frustrating.

The washer I bought brand new has never worked well. The clothes end up all bunched and twisted up together. The bleach is not distributed properly, I have big blotches of white spots. It is leveled, still shakes and everything is on one side

I purchased the Maytag Bravos MCT HE washer in 2011. Its about 3 1/2 years old and there was a very loud noise when the washer went into the spin cycle. Called the repair man and they told me the bearing and spin basket needed replaced. I had always had Kenmores with very little issues and they lasted for 12 years plus each. I get the HE model from Maytag and cant even go 3 1/2 years without some major issue. I called Maytag (Whirlpool) to complain and they said there wasnt anything they could do. I reminded them that I had checked for recalls on this model and looked into some of the complaints about this washer and that there were many of the same issues that I had plus many others. I felt like there should have been a recall on the bearing since they are going out too soon for this kind of a washer. I guess the Maytag repair man is now busier than ever since I dont see them on any advertisements anymore. Well, I will never buy a Maytag or Whirlpool appliance again after this.

The middle piece of glass on my four-year-old gas oven shattered. It was not being used, but when I called Maytag, they told me that that was not covered because I did not have an extended warranty, and that I can purchase a new oven door and would have to pay the service person. I hope they go out of business. Maytag stinks, and everyone should know this.

I had my kitchen remodeled less than 4 years ago with a Maytag refrigerator, Bosch dishwasher, and GE stove. I had a 1 year warranty, and purchased additional 2 years. The warranty ran out last year, and the refrigerator is not working. Maytag customer service said all they could offer was 1 year extended warranty for $300. I told them a refrigerator should last longer than 4 years. They agreed, but that is all they did. Ive read other online reviews, and it appears a lot of people are in the same situation (however my fridge is not on a recall list). I will never buy another Maytag product ever! My GE and Bosch appliances are working just fine.

Topload Maytag Bravos washer sounds like a jet on spin cycle. Called Maytag, no recalls or service issues. Just wanted to sell me a service contract for over 300.00 dollars that would fix it and be covered under warranty for a year on anything that went wrong. Could set me up with a service call, but it was six days from now - no thanks. The washer this replaced was a Sears which was 26 years old. It still worked and I sold it for 75.00 dollars. Guess I will stick with Sears!

We purchased a Maytag dishwasher in July 2013. In October 2014 it stopped working. None of the buttons on the control panel would light up. The service technician diagnosis was that it needs a new control panel at a cost of about $200.00. We chose not to do the repair since the technician recommended against it.

Bought new in 2006. From the beginning it shook a little. I could not use high speed without leaning against it and pulling upward on the unit. Maytag service workers came out and at first said they needed to balance it. That was not it. Then they said it was the drawers that I purchased as an option. Finally, one guy just straight up said they had no answer for it. Then came the day, last month, it was spinning and suddenly it started to rock and I ducked out because I thought the tub was coming through. I seen smoke. Yelled for the kids to get outside. With the phone in one hand calling the fire dept, I ran for the electric box & started throwing switches. Fire dept said that is what saved my house. Now it sits in my dining area because of a lawsuit I was never contacted about. No parts are available. Thats what happened when Maytag chose to send the business to China. Now they are back to making them in the USA but why would I buy again from a company that does not make good? Well I love blogging and Facebooking. I know 40% of Central FL because Ive lived here 60 years, plus my husband serve all of Orange County 35 years. This review will go out all over. Anyone need a tall table?

Purchased a Maytag Electric range Model MER8800FZ2 in 2019. The surface Scratched the first week of purchase and the stains will not come off. When I called customer service they claim they are not responsible for cosmetics. In my opinion, This model was put together with the cheapest material they could find. Maytag is not what it used to be. The Elements take a long time to heat up. Inside the oven, the Glazed Paint is cheap product also where once it stains with food it never comes off.

The refrigerator is not keeping cold. The freezer is full of frost/ice. I had this fridge looked at twice in the past. Its about 6-7 years old.In the past, Maytag was considered a high end product. I wonder where the manufacturing is taking place for most of the parts. Could be it was cheaper to go overseas and now we are all paying for unacceptable products.I will never purchase Maytag. Maytag should be selling products they can stand behind! Products that are made in the USA, where our standards are higher and we expect products that work!

Ive been a Maytag consumer since 1980. I bought washer, dryer, refrigerator and a smooth top oven. I replaced the washer and dryer with the Bravos series on November 22, 2011. Everything was fine until 6 weeks ago. The bearing went bad under the drum. 2 techs and 2 weeks later, at the cost of $527 and change spent on repair for a $650.00 machine, I started to look into reviews. Not! Can you say class action lawsuit! The fine gentlemen informed me 5 years ago about the Canada buyout, a local retailer that only sold Maytags. He shut his doors due to the fact that he will not work on junk! Oh well, he was right. 13 months worth of use and Im going to spend that kind of money. Now I understand why the repairman in the commercials retired! Shame on you. Love, crazy Mike.

Started having problems summer 2017. My dishwasher leaked and tank replaced, followed by drain pump, followed by circuit board in 2017. Didn’t have use of it for months. It has started leaking again as of Sept. 17.

Come on people are you serious! Im talking about all those people who give this washer great reviews or even mediocre reviews. This washing machine sucks! Thank God for the glass lid so you can see how terrible it washes. No water in this thing. Clothes that sit on the edge of the bowl do not agitate enough to be washed if there was water in the wash cycle. Bleach that you use in your white wash cycle is left over and gets onto your colored cycle if you wash it the color cycle next. I ** you not, mark my words that stains are left on clothes even in a cycle that has lots of water in it. If you think Im high or crazy take a look at your local Home Depot or Lowes store. Check the area for washing machines that are for sale that have been used. You will find this Maytag Bravos XL machine there. They look good and are practically brand new and they will be there for weeks on and because people return them if they get lucky to return them. I called my store and they refuse to take it back and told me to call the manufacturer. I did just that... I called the manufacturer and they told me they can send out a serviceman to check the washing machine. Butt...and a big butt, if they find nothing wrong with the washing machine that I will be charged a service fee. Bunch of **! For all of us that get stuck with this pile of garbage we can thank the tree huggers for trying to save the world with low water consumption water washing machines.

I bought this dishwasher from Sears on Tuesday July 15, 2014. It was delivered on Friday July 18, 2014. On Friday July 25, 2014 two plastic clips that hold the top rack on broke, and one whole side of the top rack fell down. I called the 1-800 # in the book. Then I called the repairman they recommended. He came out on the Monday July 28, 2014. By the time he got here, the clip on the other side broke. Now the rack was hanging by one plastic clip. While waiting for these parts, the last clip broke and the rack was completely detached. So he received the parts on Friday Aug. 1, 2014. When he arrived, lo and behold, they sent the wrong parts. He had the side tracks that hold the rack, not the cheap plastic clips that attach it to the racks. So I have had my new dishwasher 14 days, and have been able to use it a total of 4 times before it failed. I am now awaiting the new parts. The parts that broke are made from a cheap thin plastic, and this is expected to hold up the entire top rack and the dishes its holding.

I have a Maytag refrigerator that I bought 20 years ago when I moved into my new house. It’s still going strong and haven’t had any problems with it. The only thing that has been replaced is the filter. Knock on wood!!

Purchased a stackable washer and dryer (Maytag) for our new condo in Feb 2015. After it was installed a few months later the problems began. The washer wasnt removing the water from the clothes. We contacted Maytag and they informed us that they subcontract out to a company called Appliance Service of Central Florida (727-462-0394). Contacted Appliance Service and set up a date to be serviced. Since then, we have had Appliance Service out to our place over 8 times. They found fault in our control panel, our door lock, replaced our motor and have replace several other parts. It has been over 4 months since they started repairs on our machine and have informed me that they have a right to try and fix the problem. I have no problem with this but when and how long do I have to put up with this? They dont seem to care that my wife and I havent had a working washer in over 4 months.The people doing the repairs stated that this machine should have been replaced because it had or has several problems with it and after replacing the motor, electric panel etc it still isnt working. When I contacted Maytag they stated that as long as Appliance Service is working on the problem, it out of their hands. Is there anything I can do besides contacting a lawyer and spending more money?

Double door Maytag 3 years old has been leaking water in freezer floor and forming sheet of ice. After reading the reviews, I may decide to buy a different brand. Why spend more money on repairs! Very bad experience!

The control panel went bad on our Maytag dishwasher of only 4 years that is only run about once a week, A replacement part would cost more than half of what the dishwasher originally cost, so we have decided to go with a KitchenAid. Not pleased at all with the longevity of the Maytag.

We replaced a 20 year old Kenmore washer with this Centennial washer (MVWC360AW), and after 2 years we are looking for another washer. The machine will not complete the wash cycle, and when we called for service, the factory authorized service tech couldnt figure out what was wrong with it. After 2 service visits in a months time, I tried contacting the company directly with my story to see if they would help resolve the issue. I sent them a letter by mail as well as on their contact us link on the company website. They have not responded to me in any form. We will never purchase another Maytag product, and will tell everyone we can how terrible this machine is and how the company apparently doesnt even care.

I saved for this refrigerator for some time and assumed at my age this would be my last one. Thats a joke, less than 2 years and I see this water leaking on my floor. I blamed my dog at first. This was a Home Depot purchase. I love the middle drawer but the freezer has this problem. I removed the ice but it comes back. I did not purchase the extended warranty because if you have an excellent product, you dont need an extended warranty. And of course this happened RIGHT AFTER the warranty ran out. I am VERY upset with Maytag/Whirlpool. Will NEVER buy another product from them. This fridge should not have problems in less than 2 years.

I purchased a Maytag slide in range from Costco online in April 2020. Within three months a discolouration on the stainless top part of the range has happened. Costco has a ninety day period for repairs, or return on appliances. Pictures were provided to Costco at the request of Maytag. Upon review, Maytag’s response was, This is a cosmetic issue and nothing we will repair. I am an extremely disappointed consumer who will NEVER purchase a Maytag product again.

I purchased a Maytag Bravos XL washer mid November 2013. Less than six weeks later it leaked water. The repair person has been to repair it four times. The last visit was yesterday. It now has more problems than it originally had. It still leaked water. Maytag does not stand by what they sell. All they say is they will repair it. My caution to anyone reading this is never buy a Maytag appliance. I hope this review helps someone in their decision making process.

Ive had my Maytag refrigerator for 19 years and it still performs well. I keep it clean both inside and underneath. The lighting is one aspect I really appreciate as there are two bulbs in the interior so theres never a problem seeing all the contents. Also appreciated are the movable shelves on the door and the ability to raise or lower the main shelves in the body of the fridge.

I paid over $600.00 for a new maytag washing machine two years ago. It quit working a few days ago and the man said itll cost over $400.00 to fix it. Why do you people build this type of junk? I would like to hear from someone on this and why I had to pay $300.00 a year for a washer that is totally worthless now??????? ** please contact me. This is crazy to buy this washer and it only last two years.

A lot of repairs in 6 years from belts. It leaks water around seal on door. Only part of the cycles work. I would not recommend the Maytag washer to anyone. When I got it I expected or hoped it would last 10 years or more.

I purchased a Maytag dishwasher with a control panel in September of 2013. In August of 2014, the control panel died and did not allow me to run the washer. In March of 2015, the piece which was replaced died. When contacting Maytag, even when they did the repair the first time, said they were unable to cover the cost because it was now out of warranty. Ive seen several class action lawsuits around the product with Maytag. Do not buy a Maytag. It used to be a quality brand, but is now terrible.

This has been the worst washing machine I have ever owned!!! Purchased 3 years ago and this is the 3rd time the bearings dont work again. It make loud clanking noises. Then fails to spin at all. The first time it broke was the 1st year we owned it. It is sitting in our hallway and I can hardly wait for it to leave my house. Talked to the local appliance dealer and they never recommends these washers. I told dealer I must have gotten a lemon. He replied that it wasnt a lemon, that the machine tubs have gotten so much bigger and they have needed to upgrade the bearing system and are unwilling to do it. Dealer has highly recommended the Speed Queen. Based on the stellar reviews that is what will be coming to our house today. I can hardly wait. I know, its just a washing machine but frustration has overcome me. The Speed Queen has no plastic parts. We went with the knob style as opposed to the electronic push buttons. Less to go wrong. The warranty on the Speed Queen is top of the line, 5-year parts and labor. The salesperson didnt even try to sell me a warranty. No need to. Speed Queen stands by their product. I only recommend the Maytag Bravo XL if you dont have enough stress in your life.

We have owned this range for a little over a year. Oven will not hold correct heat. Have temperature sensor replaced under warranty. Did not make any difference. You can adjust temperature up or down according to actual temperature readings, but the temperature swings so much that it is worthless to try. Very hard to get food baked right.

We love our Maytag Dishwasher! It's very durable, doesn't use a lot of water and really gets our dishes exceptionally clean. The best part is that it sterilizes on the final cycle! We've long trusted any Maytag appliance in our families for generations.

Purchase in April 2010 on 12/31, motor and computer panel went out, not washing. I do not recommend this dishwasher cost to repair. Too expensive.

I have had trouble since I bought the Maytag Bravo washer. It first started out with the motherboard putting up crazy numbers. It took 2 different motherboards before that problem was fixed. Then it started with not wanting to drain; that was caused from the washer machine sucking up small clothes items in the drain plug. I had to call the Maytag repairman 4 times until I was told I had to put the small items in a laundry bag for this to stop. Now it is going off level on every wash, even when it has only 2 pieces of clothes in the machine. I am about ready to throw it out. Btw, all of my appliances are Maytag and I will never buy another Maytag appliance again or I will never recommend a Maytag to anyone.

I found this washing machine reliable for over 10 years. I paid more for this brand but it was worth the extra cost. I found this washing machine Simple to use. I would recommend this washing machine.

Dishwasher Control Panel MDB7749AWM2 - Purchased unit on 11/22/2011. June of 2014 my start button stopped working, and after searching online I guess I consider myself lucky. Spent 38 minutes on Maytag consumer service site speaking to a rep who walked me thru a reset that did not help and then explained that my machine was no longer under warranty and $149 for the service call and the cost of the part assuming it was a control panel would total over $250 on a machine I spent $500 on. I spoke to a supervisor who was only willing to sell me a control panel at 50% off and do it yourself, and while they claim there are no consumer issues with this part, they stated that the warranty on the part is only 90 days. I told them this was the last Maytag/Whirlpool/KitchenAid appliance I would purchase and they did not seem to care so I will be moving on to another dishwasher since I will not invest $250 in a fix of an item that they will only stand by for 90 days!

Purchase a Maytag washer in 2012 and less than 4 years later have to go shopping for a new washer. Purchased a Maytag because was under the impression that it was a good product and would last. Not true. The washer almost caught fire, just happen to be nearby when smoke started coming out from behind the washer, so I was able to turn off the machine and then unplug it and my husband smelt wires burning. If I hadnt been nearby we could have had a fire instead of smoke. I dont want to rain on anyone parade but I wont be recommending this product to anyone.

The refrigerator has been very dependable for over 14 years. The biggest problem we have had is failure of plastic tracks on drawers that break and had to replace drawers and other problems with plastic components like deli drawer coverlet, and door shelf door plastic. Recently we have problems with the touch control panel on front of door. Not working properly for ice dispensing and temp. control although temp is maintaining what we had set prior to failure of control panel.

We got Maytag 2000 series front load washer just over a year ago. The bearings in the drum are already worn out. I will never buy a Maytag again.

We bought a new Whirlpool dishwasher, and it was a nightmare. So after four years of that we tried their sister company Maytags dishwasher. I have to say that I think these two old American brands have been ruined. This Maytag dishwasher is always making my dishes smell like rotten fish or a dead animal. I have to dump bleach and or vinegar down in the bottom constantly to keep the stink down. And I have looked and there is no food laying in the grinder. Then we started to lose wash cycles, and the buttons (not real buttons but a cheapo control panel) started to malfunction after 2 years. Now, 3 years into it the plastic adjusters in the top rack are broken, control panel has gone totally haywire, and still smells terrible. I remember when American appliances were sturdy and reliable because they were designed by engineers. Now they must be designed by accountants and shareholders. Goodbye Maytag and Whirlpool.

This washer is the worst piece of junk I have ever purchased. From day 1 it never cleaned my clothing. It was too much money to call a repairman so I have lived with it since October 13, 2013 and I have finally been able to buy a new washer this week. My husband would come home from work and ask me why I put dirty clothing in his drawers, he said his clothes stunk and were stained. This washer just did not clean the clothing. It didnt use water. I cannot say how many times I would open it after washing a load and the clothes were dry. It saved water alright, it didnt use any and it was installed properly. If you are going to purchase a Maytag Centennial, run. Dont walk. Run, fly, look the other way, just dont buy this HUNK OF JUNK! I cant even sell it, so we will sell it on eBay for parts just to recoup some of our hard earned money! MAYTAG YOU SHOULD BE ASHAMED OF YOURSELF!

We bought a Maytag washer in 1987. It worked beautifully for years. The Maytag Centennial Washer we have now is sub-standard. It takes a full hour or more to wash one load. No quick wash feature. Today I filled the washer with soap, clothes, and pushed the button to fill it. It filled and inexplicably drained, wasting my time, water, and laundry soap. I regret buying this washer.

Our bottom freezer began building up ice. We cleared the ice and unclogged the drain gasket as per the many instructions that we found online. Researching this problem, I discovered very quickly that this is due to a faulty design of the drain grommet. A new part has been substituted by Maytag. I called Maytag customer service and they refused to supply the replacement at no cost to me and claimed there is no quality issue. This is not about the $20 for the part. It is a leading consumer brand disregarding customer satisfaction. This is also bad business. They will sacrifice their reputation for a $20 part on a $1,000+ purchase. They need to be put on notice that they cannot get away with this in the age of the web where there is total transparency.

Was assured the washer could do comforters, etc. Well, I took a video of the washer doing 5 t-shirt, 1 pair of pants, and 3 pairs of socks on the power wash cycle. Nothing tumbled. All the plate did was swish some water around on the bottom. Clothes werent clean at all. Check my Youtube video, and you can watch the leg of the pair of pants sticking up out of the water and never getting back down in to get wet. Horrible horrible machine. With that said, called the company I bought it from, and they arranged for a front loader since Id only had the machine for a couple hours. Stuck me for a second delivery fee though, which I wasnt happy about. Well see when the new one gets here Tuesday.

We purchased a new Maytag dishwasher last year when we purchased our new home. All the other appliances were Whirlpool. This dishwasher runs forever. We have huge electric bills and I am sure this is a contributing factor. We purchased it from Lowes. They have sent out two technicians who say there is nothing wrong with it. One said it was because it was in an island. The other that our water is not hot enough. He turned the water heat up and now you have to warn people using it to be careful or they will get burned. No wonder the Maytag repairman is so bored. He knows the appliances he services are junk and doesnt bother. Take my advice. Buy ANYTHING BUT Maytag!

Maytag Dishwasher MDB7749SBW03 - We purchased this dishwasher in 2013. About 1.5 years after purchase the control panel started to get flaky and different settings wouldnt work. Not long after that it stopped working at all. I did some troubleshooting and found that the ribbon cable that connects the control panel to the control board was corroded due to water/steam getting to it. Since we were past the one year warranty I bought a new control panel and things worked fine for about a year, now the panel is going bad again. I contacted Maytag and they said they cant do anything to help me. This machine is not even 3 years old and going on its second control panel. I would recommend staying away from all Maytag products.

Purchased my Maytag in November of 2010, with the freezer on bottom. Within 1 year the ice maker stopped working, and every 8 to 10 days it gets a sheet of ice on the bottom, and water runs out all over the floor. Guess, Yes the warranty expired and scared to death that Im gonna have to replace my floor. If there is a class action suit out there please inform me.

We bought our set when they first came out at Home Depot. We gave a pretty penny for the set. The first complaint was soon after I got them home; the washer gets the clothes so tangled up its hard to get them out sometimes. The 2nd complaint is, for a couple months now, the UL light comes on and beeps. I have to open the lid, close it and it starts that part of the cycle over and it usually does 4 to 5 times before it actually spins and finishes. I put it in the shop; they said they cant find out whats wrong with it. They said the leveling rods are still new looking. I was like, I know its still a newer set. Its money for nothing. I called Maytag. They want to charge me over a $100 just to come out! Rip off! Do not buy this set. Beware! Im still having problems. I will not buy a new Whirlpool set because they bought Maytag out and I will not buy a new Maytag set ever again!

In April 17, 2015, I purchased another Maytag microwave but wanted the convection oven too from Home Depot. The convection fan quit working in January 2017. I called Maytag to ask how this was covered. Maytag only has 1 year warranty on parts and labor. So basically if you dont buy an extended warranty, you are stuck with a product that quits working. Apparently, Maytags work is only good for 1 year or they would have a longer warranty. I told the Rep this when I spoke to him. He told me they normally last 5-7 years. Wow, still not acceptable. He said I had two options. Maytag could send out a repairman and it would cost almost $300. The other option was just as ridiculous. I told him I paid almost $500 to start with and it only lasted 21 months. Of course he said if I had bought extended warranty it would have helped. If I paid $500 for an oven, why should I have to pay more to cover their bad workmanship?!! I am very disappointed in the quality and price of this convection oven. The bad thing is I bought all new Maytag stainless steel appliances in 2016 to match the convection oven. The products I replaced had been in my home for 12 years with no problems.

I bought the model 2 weeks ago and the lock is already going out and it wont wash my clothes. I thought they were high quality but I guess I was wrong.

MFI2568AES - Last night we woke up because of a noise coming due to continuous snapping of the waterline against the walls of the refrigerator as well as a wall of the house structure itself. Very loud noise. I pulled the refrigerator, went behind it, and shut off the waterline. That stopped the noise and allowed me to go back to sleep. However, need your help to resolve this issue. I will appreciate if you can offer me pointers and guidance.

I am very pleased with the product, a perfect stove for cooking! It’s very easy to operate, easy to clean, multiple burners, excellent in cooking large meals, like soup, beef, Chicken and vegetable soup. It’s also very energy efficient, very safe to operate,

Maytag, you left me disillusioned and disappointed. I used to believe you, trust you. How am I going to feed my kids without a fridge? I bought our side-by-side French door refrigerator a few years ago and even bought the extended warranty (which no longer is in effect, unfortunately). Yesterday, the refrigerator failed, We called a small local repair person who could be at my home in a couple of hours. He listened and said my compressor was out, a leak was probably in there too, and that it would cost about 900 dollars or more to repair. When I called Maytag to see what they thought, they said that because I called a non-Maytag assigned repair person (even though this small-business repair guy didnt even take apart the refrigerator), I could no longer get their repair plus one year warranty offer which runs 400 dollars. But there is nothing I see on their warranty page that says this. Here I was trying to help our local economy by calling a small mom-and-pop repair person who is known in our town and has a good reputation, but I guess that by doing that minor well-intentioned act, it goes against Maytag corporate policy. Wow, how foolish do I feel now? I feel ashamed to admit this, but I actually started crying when I was on the phone with their customer help rep and asked, Isnt there something that can be done? I was thinking to myself that two months after Christmas with three kids is a tough time to replace a 1300-dollar refrigerator. I offered to pay the 400 dollars to get the refrigerator fixed by a sanctioned Maytag official with their warranty, but that I didnt know that I wasnt supposed to call anyone else besides Maytag if my appliances broke down. I would have never called our small local guy if I had known that Maytag corporate had such a policy. She said that no, there was nothing that she could do, and that is what happens to customers who call a non-Maytag assigned repair person. I guess when this happens to your fridge, you ask your neighbors if they can keep some milk, lunch meat and cheese for you, at least until you can save up for another fridge. Thank goodness that dried pasta and Ragu sauce dont have to be refrigerated. There are also cans of peas and corn and dry cereal, so it should be okay.I cant express how absolutely disappointed I am with myself and with my purchase, and how this has soured me on everything Maytag. I feel like an idiot. Can you believe that I had actually scrimped and saved up for months to buy this Maytag refrigerator and the extended warranty (hah, just to be safe)? I had bought it because I thought Maytag was a reputable company and because it was supposed to help the environment with its energy saving technology. But dont you think that a $1300 refrigerator should last more than 7 years (Believe it or not, this newer Maytag fridge was replacing a 20-year-old fridge that I gave to my cousins and which is still running to this day!)? And to add insult to injury, I already had a major repair done 4 years ago on this same French door Maytag fridge when it was only 3 years old. Maytag should offer to come out and fix their mess, but all I received when I called Robin, the supervisor, at their Tennessee call center was a, Sorry, there is nothing that I can do and there is no one else that you can speak to, and Nope, there is no one at corporate that you can call for help either and I have no advice to offer you. I can give you a mailing address though, if you like. I think I did hear pity in her voice, so that was some comfort. Pity from a call center supervisor, think about that! How awful it must be for her if that is all that she can offer to the desperate people who look to her for guidance! I actually felt sorry for her after I hung up the phone. It must be terrible to know that the company that you work for is probably mistreating its customers and all that you can offer is an Im sorry. I wonder how often someone says a rosary for her and her workers taking on those endless calls for help. How often does she cry herself to sleep after a day of that?I really dont like complaining online and I rarely do it, but this experience was just so awful and hopeless that I feel I had to say something to save other people pain and money. I hope that everyone learns from my miserable Maytag mistakes and please pass on my experiences to all of your friends and family. Those big tax refund checks will be coming soon, and I know that a lot of people upgrade their appliances with that money. Please, please think twice before you buy anything Maytag. I would feel better if I knew that people could learn from my stupidity. Remarkably, I was once gullible enough to trust and believe in American-made Maytag - goodness, was I wrong to do that. I am considering Facebooking my friends and family to let them know what happened and save them the heartache too. I hope that everyone who reads this can learn from my own mistakes and misguided trust in a company. In a world where so many companies throw away or roll over on their loyal customers, all I can say is something that I learned from a wise high school English teacher - Et tu, Maytag? .

We bought this Maytag dishwasher two years ago with a two year warranty. We paid close to $700. Six months after we bought it, it started having problems on and off. They are including: leaking water, lights going on and off, cycles are not completed. We changed the console once, and soon after that it broke down again, and this time is out of warranty. Total repair times are: 6 times in two years. My husband call the company, asked them if there is a recall for this model? They told that there is no recall. Then the repair person came. According to his repair experience he said this is the common problem and he got a lot of calls for the same problem. If he told the truth about this, then the company was lying to its consumers!!

Maytag Centennial commercial technology washer - Bought what I thought would be a great washer given the Maytag brand about 3 years ago. Started out ok But has gotten progressively louder and noisier. We cant even hear the television on the next floor of the house when the washer is running ridiculous. Now it wont work at all. Outside of warranty and a real pain. Not sure what to do but if I have to buy a new one its not going to be Ay

Worse washer ever, clothes are dirty and smelly. Customer Service is even worse. After a normal cycle clothes come out half wet, never enough water in the machine. Everything gets washed on bulky and there is soap residue on everything. Have taken clothes to the laundromat on several occasions just to get them clean. I cant wait to get rid of this piece of crap!!! Never ever buying Maytag again!! Warning to everyone... DO NOT BUY THIS MACHINE!! And with the extended warranty, they still dont cover it. :(

We purchased our Bravos XL Washer and Dryer from Home Depot in November 2012. We also purchased the three-year extended warranty. I just replaced the washer today, and definitely NOT with a Maytag. We only spent that much on the Bravos XL set as we were heading into retirement and wanted to update our appliances. Maytag has always had a decent reputation, so we decided on this particular set.This washer was a terrible purchase decision. The drain hose had to be replaced due to leaking. We handled that fine. However, just past the extended warranty period, the main bearing went out. Also, the transmission was going out, and the washer was spewing nasty black fluid all over from underneath. The repair was going to be a minimum of $750.00 just for the bearing and tub assembly, and the repairman was honest and said it wasnt worth it, to just replace the washer. We didnt even discuss the transmission issue. We were more than a little disappointed in the duration of life out of this washer. I had my other washer for 20 years plus. Thankfully, and hopefully, the dryer will remain in good working order for some time.Being a senior, this was not the expected lifetime I was after out of a major appliance. I dont need this sort of expense every four years, or less as Ive read on these reviews. On average I do 2 to 3 normal sized loads of laundry a week at most. Not good Maytag, not good. If there ever is a class action suit in regard to these machines, Im interested!

We bought a Maytag Neptune front loading washer from Bens Maytag in Surrey four years ago and it has been nothing but trouble. There is no screen in the machine to prevent small things (like coins, screws) from going behind the rubber seal and into the pump. As a result, coins frequently block off the outflow to the pump so the machine doesnt drain.We have had to pay for service calls more times than we can count, and have spent more than original price of the machine making repairs and replacing the pump. We now have learned to take off the hoses and open the pump to remove coins ourselves, which we have to do every few weeks! Bens Maytag tells us that its our fault for letting coins go in the wash. There is no accountability for the faulty design of the machine that allows this to happen. We should have cut out losses and thrown this piece of junk out three years ago. We want Maytag to take responsibility for the faulty design of this product and to credit at least our purchase price toward another machine that works properly!

Bought this Maytag XL washer and dryer in September 2012. In January 2014, the washer stopped working. Service guy came out and said the electronics went out. Then in May 2014, the dryer died. The dryer door latch broke. Would not stay shut. 2 days later, the heating element went out. Again, the service man came out. This service man said that this model is subject to break downs. This Maytag is a piece of junk. I went out and bought a Whirlpool, which I had before. I would never buy a Maytag again. I paid over 2000.00 for this Maytag and it is the worst washer and dryer I have ever had. Apparently, the Maytag repairman needs to get his butt busy. I have the Maytag now on my sunporch, waiting for the junk man to come and get it.

I bought a Maytag dishwasher (MDB7749SBW1) about 4 years ago. Ive had to replace the wiring on the control panel each year. This is clearly a design defect, and Maytag will not take any responsibility for it. Ive called each year, and am told each time that theyve never received a complaint about this issue. This year Im replacing the dishwasher. Ill never buy a Maytag product again.

Has anyone talked to an attorney to see if a class action can be filed? My fridge is leaking, sheets of ice on floor of freezer, and ice maker doesn’t work. Looks like it’s the norm for these. Please post if you have spoken with an attorney. If no one has, I am going to.

I have a 2-year-and-5-day-old frontloader washing machine. The bearing and axle broke. The repair is over $500.00. It appears to be a known problem, as Maytag knew exactly what was wrong from the description of the noise it makes. They knew all the parts that would be needed. They would send the parts but not help with the labor. Evidently, it is a two-person job requiring several hours. They are not consumer-friendly and do not seem to care that the company reputation is going bad fast.

Just bought a Maytag Bravos 4.3 cu ft washing machine from NFM. The first machine delivered was broken it didnt wash or spin the clothes. NFM sent out another one at 9:30pm. It doesnt spin the clothes out well & loads have to be small. Poorly made.

I purchased a Maytag gas range in the past few weeks with Aqua Lift Cleaning System. I have only cooked once when grease spattered on the walls and floor of the oven. I have used the Aqua Lift Cleaning System 5 (five!) times and the grease is still there and very sticky. This system clearly does not do what it was supposed to do. I was fortunate to have bought the appliance where I could return it; however, it has been quite a hassle and I will have to pay an additional $100 to have the old one removed and the new one installed! I feel like Maytag should reimburse me the $100 because it is obvious to me now that I have found hundreds of reports of people not being satisfied with this feature.

My Maytag refrigerator (bottom freezer) is about four years old now. Since the first year, it has been freezing up. The refrigerator gets warm and the freezer stays cold. Two repairmen have looked at it, replaced the electric panel and the thermostat - neither repair fixed the problem. If you completely defrost it, it will start working again. For about three years, it would work for a few months, but now it will only run for about two weeks before freezing up again. I called Maytag when this first started happening and again recently. They say they have never heard of anyone having this problem and they are sorry. The woman said she would put my complaint in my file. I certainly would recommend that people avoid Maytag refrigerators.

We purchased the Bravos X set (Model Number: MEDX700XW0 and Model Number: MVWX700XW2) form Lowes in October 2012. When the items arrived and we used the dryer for the first time in the delicate setting, the machine kept cutting off! So, Lowes brought us a new one. At first it worked but then the delicate cycle on that machine ended up not working as well a few months later. I ignored it and used the other settings. Yesterday, the washer broke. The entire basket detached! We were washing a small blanket and sheet set and kept hearing a loud banging sound. I went to check and the clothes were soaked and the entire drum was detached. I am so friggin angry! We spent over 1200 for this set and less than 3 years later, the set is ruined. I am on the phone with Maytag now b/c they need to replace this set or give us an upgraded set. They know that this set had issues yet they decided to still market and sell it. I want to sue!

I have a basic Maytag dishwasher circa 2012. Not sure of the model number. It works well, no fancy features but everything you really need is there. My only real complaint is that the heat dry cycle always seems to leave the dishes a little wet, but thats common enough for dishwashers. It cleans nicely and hasnt had any issues or breaks in 3+ years. Basic. Three wash cycles (light, normal, heavy); Extra rinse option, extra hot option, and heat dry or eco-dry (i.e. no dry). Nice big rinse aid dispenser. Its not that roomy inside. Id say the size is average. It looks nice - its white and unobtrusive. It works really well with Cascade dish pods. The bottom rack is kind of a pain if your plates are curved more than usual.

Almost two years after purchasing the Maytag Bravo XL, I am fed up. I have the exact same problems as everyone else in these reviews. Soap scum left on dark clothes since day 1. I thought maybe I was doing something wrong. I have read and re-read the manual especially the troubleshooting guide and still have the same thing happen. Its very frustrating. I constantly have to re-rinse clothes because of soap, lint, dirt, etc left on clothes. I wouldnt give away this washer to anyone, I would rather burn it. I am currently looking for a new washer, the last one I had for 11 years was a front loading Whirlpool. I should have stuck with a Whirlpool, I still have the matching dryer no problems at all.

The oven hasn’t caused any issues. It’s beautiful stainless steel and black finish creates a shiny but modest finish to my kitchen. It’s self cleaning power is also useful and saves time and where I come from time is money. It cooks food evenly just as an oven should.

On May 11, 2010, I purchased a Maytag washing machine from Lowes. On June 22, 2011, the machine wouldnt empty out on the rinse cycle. Lowes was called as the machine was only one month out of warranty. They dispatched Appliance Plus for a service call which would be $80.00 just to diagnose the problem. It turns out the machine needs three parts - a timer, an ATC switch, and a rinse switch. All totaled, this will add up to over $300.00, plus the $80.00 for the service call.Appliance Plus tried to contact Whirlpool to see if Whirlpool would at least pay for parts, being it was only one month out of warranty. The answer took 5 days and the request was denied. I was told I should contact Lowes Service Advantage and maybe they could contact Whirlpool for a special consideration, again, being it was only one month out of warranty. I made the call and they said to give them two business days turn-around for an answer. On June 30th, Lowes said Whirlpool was looking for the serial number and I provided it. They told me to give them another 2 business days turn-around. On July 3rd, I again called Lowes and they informed me that they still hadnt heard from Whirlpool. Finally, on July 7th, I received a call from Lowes saying Whirlpool denied the request.

Maytag dishwasher does not clean dishes. It has hot water and we have had a repairman look at it and he said water jets working. We have to wash all our dishes by hand before loading them into the dishwasher to sanitize.

I have a MGDB850WR0 Maytag Dryer. I have had to replace the thermo sensor/heat sensor three times in the past three years. Dryer takes forever to dry. I spoke to the repairman who told me in confidence that his company receives a lot of calls about this specific dryer for the same reason. He said the part was originally made faulty and thats why it keeps going out. The part being the thermo sensor/heat sensor.

New Maytag double oven installed by contractor in my house 18 months ago. I have had a few problems with it. The problem I am having today, the panel says error detected, remove from power source. I have had this problem a couple of times. I also have had the problem where the panel will not recognize anything I put in. I have to pull stove out of the small slot it is in, unplug and then push back. Not easy. I was the one that told contractor which Maytag range I wanted because I felt it was a good product. Problems from day one. This double oven/with range cost a pretty penny and I really cant afford a new one.