I just saw that there had been a class action lawsuit settled in 2005 for the Maytag Neptune front load washer and I was never notified as an owner! I have this crummy product and have been living with it for more than 10 years! I just scheduled a repairman to replace the moldy gasket (for the second time) and the noisy pump, and a latch that has to be slammed for a sum of $438. What a crock. I was told this was a top of the line model when I purchased it for $999. Ive never had such a piece of junk before in my life. I run loads of bleach weekly to control the mildew.

JADE model RJRS4270. Had this model for 10 years with more than 10 service calls. Always breaking down and Whirlpool will not honor the warranty. Paid for an extended warranty service to Maytag/Whirlpool offered by the manufacturer. When unit broke Whirlpools warranty service provider Assurance said Whirlpool no longer provides the parts needed, sorry can’t honor the extended warranty you had paid for, no parts, and no refund. The evaporator drip tray had been replaced three times. Asked to have the unit replaced. Whirlpool was absolutely disrespectful and only offered me to the option to buy another discounted $8K unit for a with ~ $2K discount.So far approx. $6K unit + approx. $1K extended warranty (not honored) + approx. $1K parts and service out of my pocket (Whirlpool continued to tell me it was not warranted). Although the operator’s manual said it was covered. While under warranty Whirlpool doesnt have replacement parts to service it. Multiple service tech are telling me there are many known issues with this unit. Found out there’s class action law for the same issues Im experiencing. Whirlpool only offered a new unit at approx. $6K. So total for me to date if I choose to take the discounted unit would be $12K. Dont buy this unless you have a good lawyer. Hardly seems reasonable. Extraordinary time/money loss and aggravation.Bought 8/1/05 S/N ** Model RJRS4270C $5,400. Service call 5/10/06 Repair - Freezer dripping water and pooling on floor. Service call 6/28/06 Repair - Defrost drain problem, ice backup, drip tray. Service call 7/5/06 Repair - Defrost drain problem, ice backup, drip tray. Service call 7/12/06 Repair - Unit not defrosting. Service call 8/26/06 Repair - Freezer not cooling, ice backup, fan burn out, drip tray. Service call 9/2/06 Repair - Evaporator fan not working. Replaced unit 9/_/06 S/N ** Model RJRS4270D. Maytag Dependability Plus Cert No. ** $99.00 8/02/08 thru 8/02/11. Maytag Extended Service Plan Plan No. ** $297.19 9/02/09 thru 9/01/12. Maytag Extended Service Plan Plan No. ** $405.31 9/01/12 thru 9/01/2015. Service call 10/13/10 Repair - Ice build up in fan, freezer not working. Service call 10/20/10 Repair - Installed new drip pan, bi metal, fan motor. Service call ~ 8/_/15 Repair - Service tech states, Whirlpool no longer has parts. Even though we paid hundreds to have a still active Maytag contract extended warranty. Whirlpool outsourced service to third party. Service call ~8/_/15 Service tech refuses to repair because cant get parts from Whirlpool. Asked me to find part on eBay or some other source so he could repair since Whirlpool could not provide. Got part. He did fix. Freezer stopped working 4/2/16. Customer support 4/3/16 followed owners manual instructions for warranty and call number, Whirlpool said theres no warranty and to call any local service tech. (Owners manual said compressor was still under warranty). Service call 4/4/16. Tech refused to work this Whirlpool unit, believes to be issue with the compressor leaking or system blockage or bad valve in compressor. Customer support call back - Krisi, was warranted. Jade Specialty Department. Customer support call back - Jared, no warranty, sorry. Explained contract to him. Nope/Nada. Customer support transfer - Jan, yes was warranted. Asked to speak to manager/sup. Said if you won’t honor warranty then please provide replacement. Transfer to Mike said we must schedule service through Whirlpool to fix contradicts. We asked for reference number to track. Mike said they don’t use reference numbers (contradicts Jared from when he asked me for a reference number). Two days no call from Whirlpool. Customer support call back 4/7/16 - Kari, offered small discount for equivalent new or refurbished unit $5,739 for Model KBSN602ESS. Said although under warranty, Whirlpool may not be able to provide parts to repair unit, but they will sell me an equivalent unit.

This will be the third repair of this refrigerator in one year, the same issue of the refrigerator warming up. Water all over the floor due to ice thaw. Also food spoilage. I want another refrigerator at this point. The Maytag repairman is definitely not lonely. He has more business than he can handle with this defective refrigerator. Terrible. Do Not Buy!!

Purchased a Maytag four door refrigerator and it leaks water all over the floor. Every few days I remove ice from the bottom of the freezer.

I purchased a top load Maytag washer the spring of 2019. My clothes come out partially dry, with a film/residue, and debris left on them. I was told that they use considerably less water; however there is not sufficient water to wash away small amounts of anything left on clothes. I have contacted Maytag 3 different times. Each time my concerns have been dismissed. The only solid advice they gave me was to use less soap, which hasnt changed anything. They also told me to clean my clothes before I put them in the washer (we have no children at home; Im not talking about really dirty loads). They told me there was nothing they could do, and I was just stuck with the washer. I am completely dissatisfied with this product and the Maytag service. I would not recommend their washer or their service. The dryer works just fine.

I have purchased the Bravo washer less than 2 years ago. Within one year the mother board went. They replaced it because it was less than a year. Here I am not a year later and the mother board went again. It’s not under warranty so this time its on me. I call and all they say is “there is nothing saying they are having any problems with this.” Now I happen to know my own sister bought the same washer one month before I did. She was also told it was her mother board. It was almost as much to replace than to buy a new washer and by the way she is the who recommend the product to me, so I know she called Maytag and complained so if 2 of us in the same family had an issue I find it hard to believe no one else did. You call and they could care less. I would recommend never to purchase Maytag AGAIN!

My washing machine is 2 1/2 years old. It is not overused, just 2 people in the household. Maytag wanted to sell me a contract for $320, I declined. After research I see that this machine has many complaints against it. I bought Maytag because they never need repair. I would like Maytag to fix this machine without charge or recall the machine. From what I have read, these machines are defective. The electronics are failing at 2 to 3 years.

On Thurs. Sept 25 at noon the alarms and lights started flashing on my refrigerator when I tried to get some water. I called Maytag, told them what was happening and told them to bring a motherboard when they came as nothing was working but the lights and alarms. I was told it was too close to the weekend so they would be out Mon. the 29th and I should just to get some dry ice. They came and the order said nothing about a motherboard, which is what the tech person who came also said it needed. Now they will be here on the 7th of Oct - maybe. 12 days is highly unsatisfactory for refrigerator repair. They had 4 days to see that the provider had a motherboard before the serviceman wasted a trip. Ive spent $102 on dry ice and now Im going to lose the food anyhow. I like the refrigerator but the service is really terrible so I wont be buying another Maytag appliance. The person at the call center ignored my diagnosis and it will be even worse now as over the weekend Maytag switched their call service to India!

I bought this MMV4205BAB microwave thinking Maytag was a good brand and I wanted an over the range type. Problems began when it would stop in the middle of a cooking cycle. I called the repairman as it was under warranty. It was decided by the repairman that the weight of thing was too great for its thin frame, not letting the door close correctly. I got a new one and it, from day one, would make a shorting sound every time anything was cooked, on the stove top, under it, while it was on. It finally just shorted out. I have a Maytag washer and dryer that are also junk. So, needless to say, Maytag, 3 strikes and youre out. I will never have another Maytag product and I let others know what a great product it is.

Less than 2 yrs old and starts giving UL error on spin cycle. I try replacing the springs. No relief. Notice dark brown fluid under dryer. Thing sound like a plane taking off. A little more research and Im thinking its the bearings. Looks like an expensive repair, now I have to decide whether to cut my losses. Seriously? The reviews on here are just horrible, not like this was an dl hell machine.

It looks big, but is small inside. Its hard to put in several large items. The water filter broke and too expensive to fix. I like the double doors and ice maker. I dont like the freezer drawer. It wont stay open to clean.

I purchased a Neptune washer/dryer front loader. All Neptune washers have basic design flaw over which the company should be sued. Since the bulk of the weight is in the front of the horizontal wash-drum, the entire assembly is suspended by a rear mounted bearing allowing the drum to spin. That bearing assembly is woefully under-designed and not able to support the unequally distributed weight that is inherent in any front load design.Since the forces of gravity cause a loading of the rear bearing on the front of the bearing raceway only, the machine is doomed to catastrophic failure of the entire drum system--and they all do this. When the washer goes into spin mode, it sounds like a jet engine taking off and that is a symptom of the bearing design beginning to fail which begins on the first use of the machine. The cost of the drum assembly/bearing and the labor is far more expensive than buying a new machine and therefore, not worth it. Avoid Maytag products at all costs.

Ive had a Maytag washer and dryer for 10 years. They have worked well, havent had any problems. I bought Maytag because of their excellent reliability, which has proven true. Design is not as modern as others, and doesnt have all the features, but overall solid reliable washer.

Purchased Maytag washer/dryer in November 2016. Have been dissatisfied ever since. Dryer doesnt dry clothes completely after 90 minutes on high setting. Washer leaves white residue on clothes. Noticeable on dark items. Hardly any water on deep water wash cycle. Bedding just makes a big rolled ball. White powdery residue doesnt come off easily. Rewash, dryer, brushing. Ruining my clothes. Service has been out and they dont appear to know how to correct problem. Maytag doesnt know what problem is and their engineering staff hasnt provided any information on how to fix. Maytag seems very disinterested in helping. They just thank you for being a loyal customer. Not anymore. The attached pictures were taken March 11, 2018.

Two and a half years ago I bought a Maytag dishwasher thinking it was time to upgrade from my Ge. After a year and a half the control panel went out in in it! So For a little over a $100 I replaced it. Now, a year later, the panel has gone out again!!!! What is this? Every year I have to spend over a $100 to repair this thing!! I think it is time to find a new dishwasher!

I purchased a new electric oven/stove, dishwasher and over the stove microwave. My dishwasher didn’t work from installation and it took Maytag over a month and half to repair. My oven door hasn’t worked properly since purchased and finally broke and I have been without an oven for two weeks waiting on repair. The customer service does not listen to you and seem to be completely unconcerned about your problem. I was told the item broken was a common stocked item and the repair would be quick but that was not true. The repairman told me they would have my parts in a week and would install them on a Monday. They have now scheduled my repair for Thursday. Over two weeks with no working oven. I will never purchase a Maytag appliance of any kind due to the terrible customer service.

We got Maytag 2000 series front load washer just over a year ago. The bearings in the drum are already worn out. I will never buy a Maytag again.

I spent extra money on a commercial grade Maytag dryer $1300 before taxes because it had a 10 year warranty. The motor and drum quit - and Maytag refuses to honour the warranty. I am appalled by their dishonesty and lack of integrity. I do not recommend them to anyone.

Bought Maytag Bravos in 2010. It does not clean but worse than that it rips clothing (for example: loops off pants, holes in pjs, tons of ripped towels), so many items of clothing torn that I cant keep count. Today I had a pillow case ripped apart (see image). I have had four sheets ripped that I can no longer use. Maytag should have recalled this washing machine. I have the Maytag Bravos dryer also and the drum was on backwards on it when I bought it.

Buyer Beware!! Purchased my Maytag over the range microwave in May of 2014. It has a manufacture date of Feb. 2014, and it is now Sept. 2014. It is a very nice looking unit but a bit oversized. My handyman that installed it had to raise my cabinets above my stove two inches to avoid it being too close to the range. The motor is pretty loud and It often times does not heat evenly. The light on the unit that shines down on the range is not much better than the power of a night light which is a bit disappointing considering it looks like a higher end unit, and down to the reason I am writing this review today is that for the first time I went to change the bulb. I unscrewed the the light cover which is placed awkwardly toward the very very back of the unit, only to find that when I went to twist out the burnt out bulb (that has been in there since I purchased the unit) that the bulb broke off after hearing what sounded like the break of a seal of glue, and the bottom aluminum piece of the bulb is stuck in the bulb socket. I found that the bulb is placed in an awkward place behind the light cover. Instead of the bulb facing to the left or the right or to the front of the unit it is facing toward the back which is making the bulb socket impossible to see, which means that in order to screw in the bulb you are screwing it in from an angle that you cannot see unless you climb on the range and lay on your back, or get a mirror to help see where you are screwing in the bulb. This is just a very awkward and unpractical design coming from such a well known company with such a common and ordinary product. Now I am sitting here writing this review and I am trying to figure out how I can remove that little piece of aluminum stuck in the light bulb socket and since it is not facing to the left or right and facing toward the back, it leaves me about less than 1/2 space to work with using my hand or a tool to remove that piece, or I can just leave my broken bulb piece in there and screw the cover back on until I call service for Maytag. I believe it is still under warranty but from others experience that I have read about I am not feeling confident I will receive great service or a desirable outcome. Wish me the best!! Thanks for listening!!

My Maytag top loading washer, 4 years old, stopped working in the middle of a wash cycle. Registered Maytag repairman did a diagnosis and finally identified the problem with the control board. The cost of the control board would have cost almost as much as the original wash machine especially since I had to pay for the current service call and labor (to diagnose the problem). After having read a number of other reviews from dissatisfied customers, I will not buy another Maytag product. I was under the impression that Maytag produced a superior appliance but was disappointed by this experience.

I purchased this Maytag Dishwasher Model MDB8949SBM on November 23, 2013 and installed dishwasher in late January after new cabinets/countertops were installed. After four months the control board failed. I live out in the country and Maytag does not pay for a repairman to make a special trip for repairs, so we had to wait 2 weeks when the repairman was in the area. We purchased this dishwasher on reviews which seemed pretty good, but never bothered to check on complaints of Maytag dishwashers. I can see most all complaints are the control panels failing. Well it is November 19th and the control panel has failed again. My wife said the lights blink and when she presses a wash cycle, a different wash cycle will light and blink. She will press the start button and nothing happens. You can bet I will call first thing in the morning as the warranty will expire in a few days and I will write the persons name down and the time that I talked being that Maytag seems to lose conversations with customers. I hope Maytag doesnt give me the runaround like may others on this site. I dont understand why Maytag doesnt correct this problem that they have known about for years.

We purchased our Maytag dishwasher (model MDB7609AWW2) on November 14th, 2009 from a local appliance shop in White Plains, NY. Total purchase price was $449, not including tax.Sometime in November of 2011, the unit stopped working. I tried every simple test I could think of to hopefully reset the unit. Finishing the obvious checks, I researched some possible problems on the internet latch micro switch, drainage problem, dirty latch, etc. Frustrated as nothing got it working again, I called a repairman recommended to us by the appliance store.The repairman charged me $75 for the visit just to tell me that the control board is shot. Even worse, and this is the reason for this letter, the part costs $329 plus $40 in labor! That is outrageous! If you do the math, I am facing the costs of a brand new unit to fix the old one. That might make sense if the unit was 8 years old but it is barely 2.I have sat on the decision now for a few days as I am beyond upset and I never make good decisions when I feel like this. But to recap, Maytag manufactures an appliance where its basic function - turning on - fails in 2 years and the repair cost essentially totals (to use insurance parlance) the unit. I find this absolutely unacceptable.I don’t expect Maytag to do anything for me. But I will say this; I plan on letting everyone I know just how this experience went. To make things worse, I am willing to pay for a quality unit but how does anyone know what that is anymore? For color, my grandmother has a KitchenAid dishwasher from the 1970s that is still running fine. No membrane controls, no delay functions or fancy BS super sanitary cycles and guess what, it has no control board, just plain old dials and buttons. Imagine that mechanical control? Built to last unlike the junk you see today.To remedy, I plan on picking up a used machine from the classifieds. I’ll install it myself and be able to do this for 9 years at $449, assuming it only lasts one year (I’m finding these units for $50 used). I may get lucky and find an old one from the 70s that will last a lot longer than that.

So I read the reviews when I bought this Maytag Bravo Washer and figured stuff happens. We bought the top load Maytag Brava in 2013. We bought the Home Depot warranty, 2 years later the washer was leaking water. 5 repair visits and 3 attempts to fix the leak before it was repaired. As of 4-25-17 the wash machine displayed un-level errors and started vibrating with a thundering noise. Called out warranty repair and they stated we need new bearings. Repair is scheduled in 2 days and now the wash machine is thundering and spewing oil so it is shut off. 4 years old, and like the other complaints clothes come out with dry patches and not clean. This is a bad machine, we are saving for our next washer. It will have an old style spindle/agitator, no California efficiency and probably not Maytag.

My microwave will not work when the door is shut. It says: Door open. It’s worked intermittently, doing this for about two weeks. Then my husband woke up one morning a week ago and the microwave was on like it was running, light on but the plate was not turning. So we’ve had to unplug it and do without during thanksgiving weekend. This seems to be a common issue, obviously from the reviews below, so shame on you Maytag for not owning up and doing the right thing, covering repairs or sending out a recall. It’s a $112 service call here locally plus parts and labor. I will certainly be telling others not to go with Maytag. Maytag is lucky- it turning on by itself AT NIGHT, WHILE WE WERE SLEEPING, that it did not cause a fire or something. I’m pretty upset that it’s inside a 2.5 year window and already has issues.

My dishwasher like many others have mentioned is experiencing the same control panel issues. When I set it to Wash, it spontaneously goes to Rinse Only. I am unsure exactly the age, but given the number of complaints Ive read, with the same problem, it seems as though, there was a flaw many years ago in design and regardless of issues hasnt been resolved with the newer models either. I realize appliances dont last forever, but Maytag was always known for the lonely repairmen and Id hoped the brand would continue to live up to its advertising, despite being purchased by Whirlpool.

My Maytag refrigerator is less than 5 years old; the compressor went out (only warrantied for 1 year, 5 years used to be the minimum). I contacted the company who now owns Maytag, I believe Whirlpool. They told me they can fix it, no matter what the problem is, for $380.00. It turns out they sold me an extended warranty, but that was never explained in the conversation. Prior to contacting them, I had Sears out to fix it; they are the ones that told me it was the compressor. 1 week after buying the extended warranty, the repair company came out to fix it and found out the refrigerator was unplugged and informed me it needed to be plugged in for 24 hours in order for him to determine what was wrong with it. I scheduled an appointment 1 week later. When they came back, they said it was the compressor, and they needed to order the parts. 1 week later, they came back, and the compressor they came with did not work. 3 weeks now, no refrigerator. They said they would put a rush on the order, haha. Now, I have to wait another 8 days for them to come out to repair. 4 weeks without a refrigerator? I think there is some type of implied warranty when you purchase large appliances; these companies are getting away with murder. Are refrigerators now disposable commodities? Cheaper to buy new ones than repair the new ones? What will happen to our landfills?

Purchased from Lowes October 2014, paid $680.00. Now needs $600.00 in repairs for new springs and basket rim according to a Maytag appliance repairman.Washer is leaking in the front left. Repairman thinks I need 4 new springs and a redesigned taller basket rim to keep the water from pouring out over it. Yes, it is 16 months old!! Ridiculous!

I purchased a Maytag Dishwasher (MDB7749) in 2012 and one day before my 1 year warranty was up, my start button on the control panel wouldnt work. I called P.C. Richard and they sent a repairman who fixed it. This was in June of 2013. Here I am now hand washing again 1 year and 4 months after the repair. I called P.C. Richard again and was told that all brands have their weak points and because I got it on sale in the first place, I should not feel angry.Now that I am reading the reviews from 5 years ago, I realize that P.C. Richard knew this was an issue and chose not to disclose it or stop selling it. I had my G.E. for 10+ years and will go back to one. As I have no money for another new one, I will try to learn to fix this one on You Tube.

Bought a Maytag washer from Lowes 3 years ago and it is just junk. I am 62 years old and never had a washer that actually broke down. What happened to good American technologies. I guess those days are gone, anyway dont buy a Maytag, duh. It is the day after x-mas and I have to buy another machine.

MAYTAG HAS ALWAYS BEEN MY W&D MACHINES OF CHOICE! In my opinion they are the most reliable, dependable machines on the market - for years! I would NEVER by another brand of either washer and/or dryer.

My washer has always had an odor, and I clean the gasket. It gets mold on the gasket and smells horrible! Now for my dryer, it has 3 baffles inside that helps turn and fluff the clothes, and 2 of mine have broke off. And that results in clothes that look like they have been in the dryer for weeks. And I take them out as soon as they are done drying.

I purchased a Maytag Centennial MVWC360AW washing machine on July 11, 2013 at The Home Depot. I assumed that I was getting a good product based on my Moms old Maytag washer. This machine is the farthest thing from quality that I have ever experienced. My Mom would roll over in her grave if she knew how CHEAP Whirlpool has built---what is supposed to be a---Maytag! The machine worked fairly well, at first. Even though I didnt like the low water arrangement. I like clothes to be fully immersed in water! That went on for 2 years and 5 months, until NOW the led light goes to Rinse, but it wont agitate. Then the led light goes toSpin, but it wont spin! I called a local appliance repairman and he told me that the control is bad. They cost about $250.00. Its not worth repairing!! So, Im stuck with this piece of junk! Shame on Maytag/Whirlpool for building a PIECE OF JUNK!

MF12665XEM7 Maytag Fridge water runs on the floor: After reading the review and watching the video to fix, I called Maytag. They refused to help. We bought our fridge at Nebraska Furniture Mart. We have spent a lot of money with them too. My husband called to see if they would split the cost of the service call. They refused. My floor is ruined from the water leakage onto it when we are not home. We try to catch the ice buildup and remove it before it is an issue. Why is there no class action suit? There is definitely a problem with this fridge and Im seeing it online everywhere I look.

Im have finally given up and purchased a replacement for my Maytag Bravos XL Top Loading High Efficiency Washer! The Maytag was 2 years old and I have ALWAYS had trouble with it. My towels became sour after 1 or 2 uses (sometimes they smell sour even before use!). My dark clothes ALWAYS came out of the wash LOADED with lint. I researched online to determine whether these were common problems and found several sites with suggestions such as: dont use more than 1-2 spoons full of high efficiency detergent (which recommendation I followed), Use white vinegar or liquid fabric softener. (I tried both with only minimal results.) ALSO use a dryer sheet in the dryer (I did this but it seemed like a waste since I was already using fabric softener in the washer). Dont overload the washer. (I didnt, but if I couldnt fill it, then why did I buy a washer with such a large tub ?!) Clean the washer monthly. (I faithfully did so, and tried alternating Affresh and bleach to see if theres any difference in the result... not really. Make sure you are fully drying the towels (I ALWAYS DID!).We had a Sears repair technician come to the house the last time my frustration level was overflowing and she only made me feel like an idiot, repeating some of the above recommendations and insisting they would solve the problem -- which, if they had worked, would have precluded my need to call a repair technician!!! The repair technician provided no other service or ideas to fix the problems. My husband decided we should go back to the tried and true agitator-type washer... bye-bye, Maytag Bravos.

I purchased a Maytag Bravos line washer model # mvwx500xwo back in Oct. of 2010 thinking that it would be great to save money on the water bill. I first had issues with it putting holes in my clothes. I then found out if you do not zip up all zippers and button all buttons, the machine will rip them up due to the high speed spin cycles. Now, the washer will not fill with water or start the wash cycle. I mean really, its less than two years old and I have to shell two hundred plus dollars to fix a washer that only cost $500. I guess I know what brand not to shop for next.

I purchased our Maytag dishwasher last November. Last week, the control panel went out. I called customer service and they were actually polite and helpful, except for the fact that I had to wait an entire week to have a technician come to my house. Being that I live in the Balt/DC Metro area, I would have thought they would have enough people in the area to come over faster. Anyhow, we finally had the technician come today and tell us that the control panel needs replaced and that he highly recommends an extended warranty, which costs $200 for 5 years. He let my husband know that the repair itself would cost $500 if not covered by warranty!!! What a ripoff! I purchased this dishwasher because I grew up believing in the Maytag brand. Sounds like this is an extremely common issue and if Maytag wants to make things right, they should discontinue sale of their crap product and provide those of us who are stuck with it, a complimentary 5 year warranty. I shouldnt have to pay $200 in extended warranty to make up for the fact that my control panel is likely to go out again in another year, when Ill be forced to buy a new dishwasher.

I have the Maytag Bravos washer and dryer. The machine has broken several times every year, and every year, Maytag makes me feel like it is my fault. They built a machine, and they do not stand behind it. And I cannot get a local machinist to work on it. I have asked Maytag to replace it from the start, and they refused, telling me its out of warranty. The only thing out of warranty is the frame--all parts are new. Here is the history:On 1/04/2008, I purchased it from Home Depot, and it cost $815. Then in 4/2009, there was an F51 code, and Maytag replaced the mother board after long hold times and much pleading to help me. They said they could do nothing, because it was out of warranty. It took manager to manager to manager to get the agreement to extend the warranty. (I then found that this was a regular Maytag issue.)From 9/2010 to 10/2010, an ld code occurred. The approved Maytag scheduled service had to come out 4 different times to attempt to fix the issue. One time, they said it was broken wires for the drain pump. The next, it was off balance; and the next, it was a sensor. Then the next time, they replaced the mother board again, and again after much argument that the part was less than a year old. Each time, they get more and more difficult to deal with and made me feel more and more like I am asking them for something unreasonable. The service guys said the washer was like new.... All new parts and I would never have a problem again. It cost $80 after argument, and Maytag covered the parts.Last 2/2011, problems include a fast spin, ld code, and off balance; and it stopped working. It needed new suspension rods which cost $250. Maytag paid nothing. Then in 8/2011, ld code started again, and I would have to turn off to drain and then restart to spin. Maytag called in a service call, and they never showed up. Every time, they said they read over my file and that theres nothing they can do to help me. And no one else for me to speak to.In 10/2011, the ld code came on permanently. The Maytag call I made this time again said there was nothing they could do to help me.I am so frustrated; I dont know what to do next. I threw away an older set working washer and dryer, thinking I made a great decision to upgrade to this new set. Now my family of 5 cannot wash our clothes. No one will work on the washers locally, and Maytag treats me like Im complaining for nothing and I should just spend endless dollars to fix this machine. And Im at a loss. I had to get a part for the dryer the other day, and the parts store person told me that this washer is one of Maytags mistakes. if that is so, why wont they help me?

I was so excited to get a washing machine. My excitement quickly faded two washes in when I noticed that the clothes were not completely submerged in water. I checked the handbook and it said that this is normal but at the end of the wash I still had clothes that were completely untouched by the entire washing cycle. The first couple times that the washer was used, I noticed that the water took a very long time to come out. It said it was sensing and then the water would come out in small spurts. When the wash actually started moving, wow the noise was abnormally loud. It continued to make said noise for the entire cycle. I could hear it everywhere in the house. I am so disappointed in Maytag. My father is of a much older generation and he chose this brand based on his past experiences...now I have to tell him its a hunk of junk. Save your money and buy an old fashioned machine.

Thank you all for taking the time to write these reviews. My only regret is that I am reading it now, I wish I would have read it before purchasing my own Maytag washer and dryer... I bought a Maytag MVC565FWI / YMEDC555DW1 washer and dryer duo in December 2018. I had some holes in my sons clothing, but thought maybe they were due to him being a boy of 17 year old in college, sitting all day... Also my dryer was barely drying.Called and had a 1st technician for the dryer issue. He said no wrong code and to try and clean the evacuation vent. As I am a renter, I contacted my owner to do so and he did. But I did not get to try the machine unfortunately since 5 days after the technicians visit, I was deploying to Africa. I am military and was deployed for 8 months. Upon me return, dryer still barely dries and HOLES in every load of laundry that I do. My sons and also my own clothing. This time, there is no mistaking articles that I put in came out with huge circular holes.A second visit with a technician is arranged, last Tuesday October 8th 2019. Still no codes are found. And technician suggests cleaning the conduct better. Again my owner does so. Again, up to 4 cycles of 60 min on High heat to dry articles. No economy on energy on these models! I have called Maytag today since no one has contacted me in a week for my wrecked clothing. To my request of having my appliances either replace or refunded, they say no. Policy is to send a technician. Again. After 2 visits of technical support, Maytag is sending me for a 3rd time a technician (at my cost if nothing is found again) to test the appliances. Since the technicians can not find a code on his machine, Maytag is telling me they will do nothing.I have a washer dryer that wrecks my clothing and does not dry them. (Also I feel like my clothing are never fresh scenting, I wonder how efficient they are with even the basic cleaning part..) I will have to put them in the garbage, because how can I sell them?! Talking to Maytag, is being treated like an infant that does not understand THEM, when in reality, they do not back their products at all. I feel left alone with brand new machines that have been used around 30 times in under 1 year, that I will have to through away in the dump and never ever buy from this company again. M.

We bought a Maytag Bravo washer and after less than 6 months of use, it stopped working with an F51 or 53 error (cant remember which because its been a month now). After looking online, it seems that almost everyone who buys this gets this error and has to have a part replaced! And Whirlpool hasnt recalled the faulty part even though everything Ive read says it should be a recall.Its now taken over a month to get a repair person in to fix it. From the time we called Maytag, to the referral to the service person, to the service appointment, to waiting over 2 weeks for the part to come in, its been over a month with no washer. This is unacceptable Maytag! The repair company is finally showing up tomorrow only after 3 left messages from us.Either build a better washer or stock your replacement parts with the local repair companies and you should be reimbursing your customers whove spent a lot of money at the laundromat after spending between $700 and $900 on your washing machines.

The lonely salesman in the Maytag commercial for their washing machines says it all. The first Maytag washer we owned we used for 20 years and during that time had only a belt break one time which we replaced and used for a few more years. We then moved to a new home in 2006 and decided to purchase a new Maytag.

I bought my first Maytag French Door fridge about 7 years ago. When it was two it started running water on the floor. I paid a service guy to tell me a tiny little drain in the back clogged up and stopped coil defrost water from draining out. He fixed it. A year later, the fridge stopped cooling but the freezer was cold. I hired another service man who charged me a mint to diagnose that a fan that blows cold air up into the refrigerator failed. Rather than pay him again, I ordered the part. Heres the joke--the part wasnt available. An older part was substituted. Why? The first fan motor was small to make the energy start requirements--but it was too weak to be reliable. The new motor was an earlier model--almost twice as large and powerful. So much for Energy Start. At exactly 5 years and six months, the compressor went out. Im on year two with the new one. I said to myself they cant all be that bad. Now it is leaking on the floor. I have to disassemble the freezer, remove the inner wall, defrost the coils and clean out the drain hole. Wouldnt smart engineers make an easy way to do that from the back? Seems simple.

MF12665XEM7 - Maytag Refrigerator purchased from Home Depot. We initially thought it to be a good value until it started leaking puddles of water onto the floor to the front sides of the bottom freezer drawer. This event repeated itself and I feared the water would seep between the floor tiles and begin to degrade the sub flooring or possibly cause mold as well. Upon further investigation of lying on my side and pulling the bottom drawer open, I felt, what I thought to be ice on the bottom of the refrigerators floor. I gently inserted a smooth butter knife and with a nudge, a whole sheet of ice about one half inch thick, lifted from the refrigerator floor. I have since had to repeat this about every three weeks or so. Im nearing retirement and shouldnt have to lay on my floor like this to protect my floor and to keep my wife and I from a potential hazard of a slip and fall from this water on the floor! Dependability People? Hardly! I think they got outsourced! Im disgusted! Thank you!

I purchase my first glass top stove; a Maytag. It came with a 10 year warranty on all elements and the glass top. As this is a first glass top I read through all instructions, there appeared no real warnings on what to do to maintain the glass; or rather what would damage or void a warranty. I simmered some maple syrup, and as it so often does when reaching the proper temperature, it boiled over. On a regular burner, one just uses a little elbow grease and your stove is returned its previous state. This actually pitted the glass, and as the warranty people at Maytag informed me voided the warranty, and seriously weakened the glass top suggesting it would be likely to break. Seriously?????? All of us boil stuff over on the stove top from time to time, and this damages the glass top and voids a warranty??? VERY DISAPPOINTED in Maytags product and their warranty.

Maytag 765 Washer - What a disappointment after having a Maytag set for 2 decades only to get a new one that isnt worth much quality wise. 2 new washers in 2 weeks due to a ratcheting noise that they both have. The solution??? Have a third service call only to hear, replace it (which we did) or replace the transmission. The 3rd call coming up will be the same. What good is a new transmission going to fix it when the last 2 machines had New transmissions. Quality??? I dont think so. Oh, I had to buy the second replacement in order to get credit for the first one. This was at Lowes. Is there even a quality washer out there anymore?

Just read Ann of Colorados (posting April of 2014) message about her Maytag Bravo washing machine and its like I wrote it myself! Our Bravo started with making a loud noise during the spin cycle which turned into oil or a dark liquid spraying out from under the machine, along with saying UL, so I would adjust the load and get it going again only for it to start the spin and rinse cycle all over too! We have 5 people in our family and cannot afford to not have a working machine. We purchased this machine only a few years back to replace another product that was also a piece of junk. I guess as a last resort I will try a Spin Queen which is American made and hopefully will work! Very disappointed in Maytag. Whatever happened to Machines lasting like they did for our Grandparents?

Im living in a shop lot area and its near a university school. It has different laundromat stores here, and the cheapest is the one who have Maytag washers. So Ive been going there to wash clothes and as time passes, I noticed that the clothes have been getting stains after washing and these stains cannot be removed easily. Ive read reviews about clothes getting stained using Maytag washers and I cant believe that it happened to me. I dont know whats with Maytag that makes the clothes dirty/stained. I went to other laundromat stores that are not using Maytag washers. Its quite expensive, but it really makes your clothes clean.

I had a Maytag washing machine replaced under warranty back in 2011 via Maytags Extended Service Plan. This took me several months to get done because of back and forth issues with Maytag not wanting to honor the replacement. Executive Support had to get involved after I wrote a complaint on this site. When they replaced this, they sent me forms to extend my warranty, which I did. They never changed the model or serial number so Ive been paying for 2 years now for an extended warranty on a machine I do not own.The new washer broke and I called in for service on 11/18/13. Active Appliance was sent out, said it was an easy fix but they needed to order a part. On 11/20/13 they contacted me to tell me I needed to speak to Maytag because my Model/Serial didnt match with my warranty records. I double-checked these and called Maytag Extended Service and was told that I would need to speak to sales at 866-730-6094. I spoke to someone named Lindsey there who told me that I would need to send a letter in to cancel my policy and request a refund for the 2 years Id been paying for a non-existent unit and that they could start a new policy for me and get a service order in without issue. My call was disconnected during this and when I called back, I was told to call back in the morning to get back to Lindsey because the office was closing and they couldnt do callbacks.I called back on 11/21/13 and spoke to Sam who verified that the letter was needed to cancel and refund but that I would have to pay for the repair to the washer myself and theyd tack on the cost of the new warranty onto that bill so Id be covered AFTER THE FACT. Because the unit wasnt covered under warranty, Id have to cover the costs myself and it had been MY responsibility, not theirs, to make sure that the correct model/serial was on the coverage.Maytag sent me the forms and I would expect them to have added the new information on it...not send me forms with my original washing machine information. Especially as this had been escalated to Executive Support and the person I dealt with there had gone over everything to make sure it all got handled in a satisfactory matter. So for now, Im waiting for a callback from the original rep, Lindsey, but Maytag tends to Stonewall and not return calls so Im dreading how long this entire process is going to take and cost.

Weve had 2 Maytag washers that lasted a combined 41 years. Five years ago we purchased a Bravos XL top load washing machine directly from Whirlpool. Like many other reviews, it is impossible to keep the machine from going out of balance and trying to tear the laundry room apart. I called Maytag and of course they want to make sure the machine is level in at least 3 dimensional space as well as 2 parallel dimensions per String Theory. As far as the 3 dimensions, I assured them I had already thought of this (as an aside, ever try to find any flat metal on one of these machines? Kind of helps when using a level.)So after more exciting conversation, they offered me a Warranty for $437. While trying to control my laughter, I said I could trash the Bravos and buy a new machine for that price. As far as repairing it, it cost $120 for a repairman to grace my door step plus $35 every 15 minutes plus parts -- again, the decision is to trash it and buy a new machine. In case I was too subtle in my comments, I WILL NEVER BUY A WHIRLPOOL PRODUCT AGAIN. Im too frustrated to tell you about my KitchenAid fridge. As much as I detest it, I am forced to join the buy and trash 5 year club . Sometimes the good old days were really better.

I bought this machine because it has a (deep water wash), which means there is a lot of water, enough to cover the clothes, at least I thought so, the salesman seemed to think so as well! But no, it does not come close to covering the clothes, false advertising! I must put my clothes in a large bucket, soak the clothes with water, then bring the bucket to the washer and empty it into it, because of the weight of the water, the machine adds almost enough water to cover the clothes.Another big problem with this washer is the fact that if I lift the top in mid-wash, while I do something, not wanting to listen to the irritating sound it makes in my apartment, after 10 minutes it starts to drain and there is no way to stop it, I must wait until it completely drains and restart the machine. This machine has the stench of government on it!!! My advice, keep your old machine.

No motor is available for the Bravos washer machine which is 5 years old! Now the machine is garbage and I need to buy a new one. I thought Maytag was a great brand so I purchased the Bravos but now I understand from the company that no motor replacements are available!! Wtf? Maytag/Whirlpool dont care for loyal supporters so, I am TELLING EVERYONE not to purchase Maytag/Whirlpool appliances whose name has gone for a dump with this latest situation.

MDB4949SDM1 - After owning Maytag model MDB/C-2 for thirteen (13) plus years, I decided to purchase the subject Maytag Model when my 13 year old died. Big mistake. Previous model was very simplistic in rack design and it provided user-friendly options such as two detachable baskets for silverware and a special rack for delicate items.The new model has been designed so your dishes go in on angles on the top rack and as such bowls, small plates etc never stay in place once you move the rack and the lower rack configuration was redesigned and the rear area which was open to allow for bigger pots and pans to fit better has been removed, so now you have to lay your pans on top of the tines, very difficult to low the dishwasher.Additionally, I purchased the stainless steel model; apparently in the coating process a drip pattern was sealed that you can see when sunlight hits dishwasher. Further the stainless steel face that they bond to the door has popped, so when you grab the handle the face pops in and out. Lastly the new design has an adjustable upper rack; I tried numerous times to adjust the rack and couldnt so when I called Customer Service for these issues, it basically boils down to if the Service Man comes out and determines my issues are cosmetic and the rack which Ive never been able to adjust should happen to work then I have to pay the service call as there is not warranty coverage. So I declined the Service Call and advised that this would be my last Maytag purchase. I highly recommend anyone considering this unit fully investigate and test out before buying.

I just bought my Maytag Range model #MGR8700DS2 in August 2016. Bought Maytag because I always thought it was one of the best with the best warranty around. Now I am not so sure. After using it the first time, found that when you are baking anything in the oven the burner control knobs get very hot. That is because they designed the knob area to be right above where the heat vents out from the oven door. The knobs get so hot that you almost burn yourself if you touch them. This is a bad design in my opinion especially if you have any kids around. Even the sides of the oven get way too hot. This is also bad because of the tight spacing to your cabinets. I contacted Maytag about this and got a OH WELL kind of reply to my problem. You bought it and you are stuck with it. I would not recommend buying this model to anyone.

I just finished paying off my Maytag Bravos series washer and dryer, and now they are failing! The washer isnt getting dirt out and the dryer power button broke. And its not like I can use some pliers to get the switch to work, its like the part that controls the power just dropped out of existence, leaving me with a knob in my hand that connects to nothing! Of course, the limited warranty only covers the drums, not the little dinky parts that break more easily. I had inherited a set of Maytags and they were well over 20 years old (possibly 30) and they both were powerhouses. But this is terrible! I feel super disappointed that Im going to have to buy a new set after only owning these for 18 months. I know I WONT be buying Maytag ever again, though!

We purchased a Maytag Commercial Technology washer from Lowes. After having the washer for only 3 months, the drum failed, an entire load of clothes was turned black with oil, and my washer was out of service for months. The drum had to be replaced. They did not offer me a replacement. I was just without a washer. They couldnt get the parts because of supply issues created by Covid. I was offered a 2-year additional warranty which should have carried me through 2022. Last week, I called to use the warranty - service was scheduled (and I was told that I did indeed have a warranty by the service team.) I was then told by the repair team that I was out of warranty. Maytags notes show I was only offered a 1 year additional warranty. I talked with Management at Maytag/Whirlpool - they will do nothing for me. Shame on me for not getting that in writing. Shame on Whirlpool/Maytag for lying to me. The washer has been a nightmare! Dont buy one.

Maytag Model # MMV4205DS - First Maytag microwave lasted just over a year before it quit. Replaced with same model to avoid install hassle and 1 year and 4 months later got the dreaded open and close door message. Read so many horror stories about repair service for Maytag that I decided not to bother and purchased a GE. I will never ever, ever buy anything Maytag ever again...

Within the first six months the drive on the washer went out. Had to order it from another city cost over 200.00 for it then had it put in. The dryer works most of the time but now and then it just dont dry all the way.

We bought a Maytag dishwasher March 2012 and the unit wouldnt turn on October 2013 - 6 months after the warranty ended. We called their service department and they told us to unplug the dishwasher or turn off the circuit breaker. We did so and the unit still would not turn on. We called a repairman who advised us that the touch pad was not working. The cost with parts and labor would be close to $300 which was more than half the original price. We repaired it and I sent all the papers with a letter to the consumer department and today I got a call advising us that they would not do anything. Do you think I have any further recourse? If not, I will never buy a Maytag product again and will advise anyone within a listening area as to how we were treated.

In reading the reviews of a Maytag Dishwasher, I am also frustrated in the dishwasher is only 3 years old and the start button does not work. It cost $75.00 for the repair person to come in to take a look at it which they deduct from the cost, total repair cost $300.00. Did not make sense at this time to have to pay the $75.00 repair person and then purchase another $500.00 dishwasher so paid the total $300.00 hoping to get a few more years out of Maytag dishwasher. By the other reviews, may not be possible. Just very frustrating.

My washing machine was noisy from the start. We had recently purchased a new fridge and were told when we questioned its noise thats just the way they are. So we didnt question the noisy washer as we should have. The noise got louder as time went on and at the 18 month mark, it was so bad, we had someone look at it. The washer had never cleaned as well as expected, but again, we were too busy to follow up. The repairman advised that the bearing and tub needed to be replaced! Augh! $450 for parts $300 for labour! I contacted Maytag/Whirlpool and was advised they would go good for the parts, I would have to pay labour. Not being terribly impressed, did a bit of research and was told it was worth fixing. As it was technically out of warranty, I was lucky to have them pay for parts. Took 6 weeks to get part. In that time, had questions about delay, etc... at one point was yelled at on the phone by Melissa from Whirlpool as I asked to speak to a supervisor. So fun :( First part comes and it is defective, luckily there was another one in Vancouver, so only an additional 4 day wait. My machine is now fixed. It is extremely quiet and cleans very well. Suffice to say, it was defective from the start. So, Ive gotten to pay an extra $300 over retail to have a working machine! Lucky me! Repairman also advised that he recommends everyone to purchase the additional 5 year warranty as the manufacturers are now only making machines with a 7 year life expectancy and I was VERY lucky in the beginning to get someone to even talk to me after the 1 year mark.

Maytag BRAVOS XL Washer - The worst washer I have ever used. Do not buy! It does not use enough water and leaves a white scummy residue on dark clothes. You have to wash them all off in warm water and then send it through one or two more rinses to get it washed off. I may as well do laundry by hand! Absolutely disgusting!

I have owned this washer for 3 years and purchased it to match the Centennial Dryer and because of its advertised commercial grade components. The washer has just now turned 3 years old and has never been abused but I have been told the drum bearings are going out.

My old Maytag is still working after 20 years but my husband surprised me with a new pair! Washers is just pure junk. Not enough water to hardly wet the clothes. They just rub together and get worn out looking, towels are rough and not soft but my biggest complaint is the AWFUL wrinkles! I have to iron everything! Only had it 3 days, called Menards and asked if we could return for an exchange or upgrade and they said no. If this is the best American Made has to offer, then I will look at the Samsung! Shame on you Maytag. Not one good review on here and you do nothing to restore confidence in American Made. I will spread the word - NEVER by a Maytag or an appliance from Menards. Neither one stands behind the piece of junk!

My refrigerator is a lemon! We bought a Maytag bottom freezer French door refrigerator model #MFD2561HEW in May of 2007. Less than a year later, it stopped working and ruined all the food inside. I cant remember the problem that time, but it was fixed by Maytag and we were reimbursed for a portion of the food we lost. Two years later, the temperature got warm in the refrigerator and freezer sections, and we were gone for a couple of days, so when we got home, all of our food was spoiled. This time we had an extended warranty in effect and they replaced a circuit board, but we were out the food. A few months later, the same thing happened. This time we were home and saved most of the food. The compressor was replaced, again under warranty, but it took 2 weeks to get the part. Now, less than a year later, the freezer and refrigerator compartments are getting too warm and frost is forming in the back of the freezer. When it finally does get cool, it freezes the food in the refrigerator section. It also makes loud bumping sounds. I paid $80 to a repairman today to tell me that theres nothing wrong with it, thats just the way it runs! He suggested I put a gallon of milk jugs filled with water in the freezer to hold the temperature when it starts to rise! This piece of junk is just 5 years old! When I complained, I was told to call Maytag and discuss it with them. This refrigerator was not cheap and I see that many others have had similar problems. How do they get away with selling an inferior product?

We spent over $1,200 on a Maytag washer on 12/2015 and it did not work properly. The door got locked, had a couple loads moldy because we could not get it open. Didnt drain either. Maytag had someone come look at it 3 times and it still didnt work. Called Maytag and now they told me that they cant do anything about it because is not under their 1 year guarantee. And of course they are very sorry for my unfortunate inconvenience. I thought they had a good honest reputation but... Im just disappointed!

The washer w10420491A is 2 1/2 years old and got the F51 code. The result is the hub bearing are shot along with a circuit board. I would stay away from any Maytag Bravos washers.

I purchased the Maytag Neptune set in 2004 and was not informed there was a class action lawsuit and was never notified. When washer quit working, I called Maytag who sold me a $300 service contract. They came out and said they couldnt fix the washer and I needed to buy a new one. I paid a fortune for this piece of junk and now have to spend another $700 to get a new washer. I will never buy Maytag again. How can they get away with selling washers that are on recall and involved in a lawsuit?

I purchased a new Maytag washer and dryer March 2021, I have owned past Maytag washer and dryers, thinking they were the top of the line products, not this time, The washer, I put the clothes in barely covers the clothes, so I put it on deep water wash, when the clothes are all done, they look like they did when I first put them in the washer, dirty clothes, whites are dirty, towels look like they got dirt spots on them. The machine makes really weird noises, my little dog starts to shake, gets so scared, she runs under the bed and wont come out. The dryer, makes a very loud buzzer sound, she gets so nervous, when she hears it, she jumps up into my husbands arms shaking. I will never buy a Maytag washer and dryer ever again, they are totally different then the old ones, they had a good product and ruined it.

Bought brand new Maytag dishwasher. Worked great for 3 years. Then caught on fire. Couldnt contact maytag for a month because when you call your on hold for 30 minutes. Then when I do contact them they will only want to give 50%off another of their products that Ive already had catch on fire. I will never buy another one ever.

If I could rate it lower than 1 star, I would. We bought ours new in 2005. Within 6 months, the main pulley for spinning the drum fell off not once but thrice. The repair tech said that the shaft was machined incorrectly at the factory and the bolt that would normally hold it on was backing out. The 3rd time it happened was close to the end of the warranty and the tech could not make it out before the warranty date. When he did show up, they wanted to charge us. I wound up putting the part in myself. Two months later, the suds alarm came on, which caused the water valve to open. The pump kicked out and the water valve stayed on flooding my basement and the electronics in the washer. This happened twice. The second time was a week ago and I tossed the ** out to the curb. We also have a Maytag Gemini double stove which does not work either. This is the second and last Maytag appliance that I will ever own. They are junk!

In July, 2014. I bought brand new Maytag refrigerator with bottom freezer. After 4 years, compressor leaked, and not cooling at all. I tried to check warranty, and Whirlpool Canada said that only specific model has 10-year warranty on compressor issue and mines does not have. So frustrating. Simply dont buy Whirlpool product. This is totally garbage and not reliable company. LG or Samsung has 10-year warranty on compressor for every product.

Maytag top load 300 series washer - This is the worst washer I have owned! It does not wash items- especially sheets - without getting totally tangled up and twisted! I wish I had my old one back that lasted 20+ years. I will NEVER buy another.

Failure to drain after 3 years. Was disappointing so repairman fixed problem, a fuse, in 3 minutes but charged $300! Since then I make my own repairs and have had no problems that I can complain about. Both Maytag Neptune drier and washer have worked well. Buzzer just failed.

We had a repairman come out and take a torn pillowcase out that was jamming. It worked for a couple of weeks, now refuses to start. We have decided to rid ourselves of the Bravos 300 washing machine and not deal with Maytag any more. I would not advise anyone to buy a washer of this type, as it never really got the clothes clean to begin with.

I also purchased a Maytag dishwasher a few years ago. It has never worked that well. We had a repairman come out once to replace the control board but the problem soon returned. Interestingly, we found that if we wait long enough until the control panel is in the mood, the dishwasher works again and the control panel responds to button pushes, until the problem returns.I dont recall what model I purchased but it seems to be irrelevant. From reading the other customer complaints, its quite obvious that all Maytag dishwashers inherently have problems with their control panels and Maytag intends on doing nothing about it. I guess the extra repair costs that their customers have to pay for their defective products brings in some additional revenue to Maytag, so theres no real motivation for them to fix their ** products.

Same as all the others, bought this dishwasher about a year and a half ago for a new home. Didnt get the CO until 3 mo. ago and already having same problem with the keyboard flashing and not working properly. Very pathetic to believe less than 100 washes and were going to need a new washer, that works out to be about $ 5.00 a load. Wish someone could help. Model mdb7749sbb0. Thanks.

The freezer leaks water onto the floor in large pools. Had it repaired, two weeks later, still leaks. Very unhappy with the performance of the bottom freezer Maytag refrigerator.

Purchased Maytag 4000 series washer Feb. 26 2011 - within six months Maytag warranty replaced the drum and bearings, within another few months Maytag worked on the drum again. Year two started out with the warranty contract replace the drum and bearings again. Oct 1 2014 called for service again, the drum not moving and having to wait 2 weeks for Tech. to checkout the machine then order parts. I have 7 children at home and that didnt matter to anyone. After reading online the number of 4000 series Maytag machines with this problem somebody needs to make Maytag recall and replace them.

This dishwasher was here when we bought our home. It has been heating up way too much on the drying cycle. I turn it off and air dry the dishes but today I noticed it melted my plastic measuring cup. I had the heat turned off and opened it as soon as it started the drying cycle.

Well I must say I concur with all previous posts. I just replaced my Bravos with a Samsung after my jet plane of a washer died. My repair guy said it was not worth it to fix it. I had already replaced the shocks two years ago but I did have mine for 8 years. I have had the same problems as previous posts - rust, smell, holes, broken, too expensive! Hello to Samsung!!

Although we have always had Maytags, this was the first time we purchased a front load washer. The Maytag Neptune washer smells and your clothes stink. We have purchased the most expensive laundry products, washed and rewashed clothes and have no other recourse but to buy new machines again. We will not be purchasing Maytag or Whirlpool. I would give it a minus 5 stars.

The design capacity of the dishwasher is not conducive to cleaning a full load. Within 3 months of purchase one of the interior baskets broke. I will never buy another Maytag product again. I was a fool in believing this was a top of the line dishwasher.

Maytag Bravos quiet series 300 - We have had this washing machine for approx. 2 years and there is rust marking around the opening of the spout where the bleach is poured into. We also find that we have to do the clean cycle quite often. And it bounces and make a loud noise if there is not enough clothing in it… even on the bulky cycle. I WOULD NOT RECOMMEND THIS PRODUCT TO ANYONE! And we have been loyal purchasers for 40 plus years!

Im furious beyond belief with Maytag. Im furious at myself for being stupid enough to purchase all new Maytag appliances when I purchased this home as I had horrible experiences with them in my former home. This concerns the Maytag over the range microwave oven model MMV4205AA. First of all, within 6 or 7 months after purchasing it while cooking a frozen dinner, the turntable just cracked in half. Maytag wanted $89 to replace it. I knew when the turntable cracked that there were more issues to come. That is not normal in any way for that to occur in a microwave.Problems continued, of course, and with each call to Maytag, they would say the same thing the microwave is out of warranty and refused to assist me. Its not some little table top thing that one can just toss out and buy a new one. I paid about $400 for it from Home Depot. Last week, without it even being turned on, it just stopped working. I checked the electrical supply and conduit to make sure that was okay. I called numerous service organizations who told me this sudden breakdown when the microwave isnt even turned on is a known issue with this model and several other Maytag over the range models. Ive called them (Maytag) three times in the last week and they refuse to provide any allowance and hear the same old thing, the microwave is out of warranty. I was willing to have them even just provide some assistance rather than replace the microwave. Ive been told by numerous service organizations that this is a known issue and that even if they repair it, it will occur again and again and Im best off purchasing a different brand, which I cannot afford. They gave me phone numbers for service organizations authorized to service Maytag products and this just goes to show how out of touch they are. They gave me one that isnt even in business anymore. How professional, not!Warning: Purchase Maytag at your own risk. I give you fair warning. Every single Maytag product Ive ever owned has been a problem. I will never, ever, ever purchase another Maytag product again. I would think just out of decent customer relations, that theyd repair this issue. To be honest, I dont really trust a repair as Ive been told it will happen again and again. There was no notice that the microwave was breaking down either. It wasnt turned on. One day, I went to use it and it just wouldnt work. Actually, I went to use the timer on it and thats how I found out it was dust. My advice is stay away from Maytag. If you read reports, there are more complaints on Maytag than any other appliance manufacturer in existence. Not only on their products, but their customer service too.

I have used Maytag washer and dryer for over 20 yrs. I recently replaced the set we purchased in 1988 because the washer broke down but I have never had a great problem with it either. I do on a average of 3 loads of laundry a week. I measure my detergents, mostly wash on warm or cold and I keep the filters and machines clean. I would buy the same maker should I need to replace them.

Bought new and only had one service call in 20 years. The control panel was replaced. Since then, the dishwasher has performed well and, factually, was far less expensive than many other models! That figured in our decision when remodeling our kitchen back then.

We had the same problem that everyone is complaining about re: frozen water in bottom of freezer dripping out onto floor. Swore when I got rid of the Maytag smooth top stove that broke after 5 years that I would never get another Maytag but broke down and bought this fridge. Maytag rep made it clear that the Fridge had a NOTE on file about the drain, but it was NOT a product recall. So after virtually taking the freezer apart before the repairman came, we ended up paying $120.00 for the repair, not the part. Yippee. Please note that the repairman told us we saved a lot of money by taking apart the freezer so most repairs probably cost a lot more than ours.

We purchased our Maytag Bravos just under two years ago. Over the past month or so, we noticed the spin cycle was getting louder and louder. Today we had the service man come out. He informed us that our 2-year-old machine will require new bearings and a new basket, which equates to over $700 in repairs. The repairman said he has seen more and more of this with these high efficiency washers. He suggested that anyone buying these new washers be sure to buy the extended warranty.I for one am completely disappointed that one can spend that much money for a washer with a two-year shelf life. I personally think this is planned obsolescence created by the manufacturers. The serviceman also said the LG versions of these washers have a large increase in electronic problems. Be warned, we have very few choices these days so buyers beware.

I have a new Centennial Maytag dryer. What a horrible sound it makes when the time is up!!! I had another Maytag dryer for 19 years and it did not sound as obnoxious as this new one. HELP!! I can tell some man invented it.

Dishwasher is just 2 years old. Touch panel is bad, not Maytag of old. Waiting for the corporate apology. Seems to me that this is a common problem and a case of poor engineering. Also seems like a case of the middle American getting worked over by the big corporate giant. Not happy. Will not suggest Maytag to anyone. Not looking forward to having to replace something that should have lasted significantly longer.

Our washing machine is 3 years old. About a year ago we started to see hairline cracks on the plastic lid in the bottom corners by the hinges. These have now become huge and pieces of plastic are breaking off every time we do a load of laundry. Maytag (under the Whirlpool brand) will not replace the lid for us. We paid $130 for a tech to come out and confirm what we already knew - that we need a new lid. And now the parts and labor will cost over $550. We have called customer service several times and spoken to a supervisor and the best they can offer us is to pay for the part which still leaves us to pay over $400 out of pocket to repair a $600 washing machine. This seems to be a common problem and is all over Google, yet Maytag is not willing to help their customers.

We were sold a Maytag Neptune washer mah550bbw in 2004 when it was already on recall by Maytag and a class action lawsuit was filed against Maytag. We also bought an extended warranty. Now we have the same problems as the lawsuit. We own dry cleaners so we do laundry once a month for small articles. For the last few months the clothes have an odor and they come out looking not clean. We were sold a defective and recalled product and are not happy right now. We would like a fast resolution to this problem; otherwise, we seek legal actions.

Machine (Washing machine front loader model # MHW 5500 FC1) purchased August 2017. From the start Service Dept USA told me to unplug and re-plug anytime I had a problem as this problem started right away right after installation. In January it was getting stuck on the spin cycle. Unplug and re-plug to no avail. MAYTAG DO NOT have their own technicians just so you know. In the my area they use two subcontractors. In January they sent out the first sub-contractor from Appliance Wizards. He is a one man operation I later found out. As soon as he saw that I had a stacked washer and dryer he told me that this was my problem. He pushed a bunch of buttons on the machine, obviously re-setting the motherboard in a different way than unplug and re-plug and told me that there was nothing wrong with my machine. Not true. Machine was getting stuck again. Called Whirlpool service USA again. Told them not to send the same company. This time they sent JC Service. Excellent company. Kyle came out, identified that it was the motherboard. He claimed that they had other consumers with the same problem but that MAYTAG has corrected the problem and he went ahead and ordered a new motherboard. Waited 8 days and Kyle and another serviceman came and installed the new motherboard two days ago. Yesterday I put in my first load and the whole machine went dead. Kyle came again. He claims it is the motherboard again and he ordered a new one. I called Whirlpool service USA and spoke to Tina. All I wanted them to do is to ship my now, third motherboard quickly by courier so that I would not have to wait another 8 days without a washer. Her resolution was to extend my warranty by 6 months. I advised her that I had purchased a 4 year warranty but if they did not fix it so I can use it, even a ten year warranty would be of no use. So then she went and started reciting THEIR RULE OF LAW with regards to their protocol and told me that if needed they will replace my motherboard as many times as needed. She would not address sending the motherboard quickly. I asked for a supervisor several times and finally she agreed to put me through to the supervisor. She was worst than Tina. She agreed to check with the parts department and if possible she would ship it out by courier. I asked her to keep me on hold while she checked. She came back saying that they were not answering and that IN FACT they could not ship it out expeditiously. So, IN OTHER WORDS, SHE WAS LYING TO ME TO GET ME OFF HER LINE!!!! I asked her to give me the e-mail address of the EXECUTIVE OFFICE for Whirlpool. She claimed that she did not have their e-mail address and that the only way to communicate with them was by snail mail. I checked the internet and found a telephone number for the Executive office in Mississauga. I called them. The menu asked to push 5 for... get this... CUSTOMER EXPERIENCE... I pushed 5, followed by a bunch of beeps and a busy signal and disconnect. I tried 3 times. So there you go. This is their way of giving you a Customer Experience. Then I found a number for the Executive office in the USA. I was able to reach Latisha from the executive team and she assured me that if I were a USA resident she would have that motherboard shipped to be by courier right away. Because I am in Canada she was going to contact them to give me a call but that now I had to wait till Monday. 4 days to get back to me from Canada. Yet when it comes to service and parts, everything is arranged in the USA and everything comes from the USA because it is more cost effective for them. Who cares about the consumer. By then the motherboard will have left three days to arrive. 7 days take away 4 equals 3, take away a day for courier, depending on what time they call me on Monday, otherwise you have to take away two days, and then it will be all for nothing. But again, they must have so many complaints at the EXECUTIVE LEVEL, that they cannot call right away. So folks, note that Whirlpool has not recalled these machines with a defective motherboard, they are still selling them to unsuspecting consumers. They are not making an effort to send them out quickly or keep some in stock locally. BUT THE WORST OF ALL IS THAT THEY ARE REPLACING THE DEFECTIVE MOTHERBOARDS WITH OTHER DEFECTIVE MOTHERBOARDS!!!! This is outrageous!!!! I shall update my review once I hear from the very busy executive office for client care, and again once the new motherboard goes in. I shall post my order number and receipt when I update this review as my husband has all this and he is away. However I can give a work order number from service: **.

Within a year of purchasing this washing machine, I needed to schedule a repair service because the washer started making an unfamiliar noise. Repair Service shows up and refuses to touch my washer. The ink on the Serial and Model number (stick on label) inside the washing machine door has washed off. Sticker label in excellent shape, except all the ink has come off. If the Repair Serviceman cannot read the label, NO SERVICE FOR YOU. MY SAGA... Did you know that if your washer or dryer does not have a readable serial number on the machine, NO repair service will work on it. It does not matter if you have all the paperwork showing this information. If the original label is unreadable, no repair service will touch it because they will be fired. Maytag changes parts on a model all the time. The serial number is the ONLY way a serviceman can tell exactly what parts your washer was made with. Apparently the serial and model number label sticker was not printed with permanent ink. The Repair Service said the Serial and Model number ink washed off the label because the sticker was incorrectly put on the inside of the washer door at the bottom. But they were WRONG! Maytag shows online that is exactly where the serial and model number sticker is supposed to be located. So, I called Maytag to order a new serial number (stick on) label for our washer. I gave Maytag the information and I was told I would have the label in two weeks. Then I called back a week or so later to make sure the serial number was ordered and on the way. Maytag said there was a misunderstanding, and that they received my request on 6/17/15 and it was sent to the ONE AND ONLY GUY that makes replacement serial number tags and he was sent my request on 6/22/15. Maytag said it would take the one and only man quite some time to make the label (SINCE THERE IS ONLY ONE!!!) and I could expect to receive the replacement label in 4 to 6 weeks and they were sorry, but there was absolutely NOTHING they could do about it. So as my year old washer sits for over a month, Im going to the Laundromat each week. We should have received the new serial number on August 6, 2015. So it’s taken almost 2 months and my label is close to two weeks late. To date I have not received my serial number. I tried to use MAYTAG chat, dont bother, they said they couldnt help me. I needed to call in. So I emailed Maytag today for their support services to tell me WHEN I can expect to receive my new serial number label. I bought this through hhGregg. Check your Maytag washer. IF THE SERIAL NUMBER AND MODEL NUMBER LABEL ARE INSIDE THE DOOR, CHECK TO SEE IF THE INK IS COMING OFF THE MACHINE LABEL, and order a new one NOW if it is, or you will not be able to get your washer serviced. Do not put new label back on the inside of the washer door. This is just unbelievable.

The fridge has a grinding noise that is getting worse, by the day. I cannot seem to define the exact location of problem, whether the freezer or the fridge. Maytag you stink, and your web site stinks, too.

I own a Maytag dishwasher model number MDB7749cBM 2. The panel on the dishwasher stopped working. It is only a year old. Its too new to break down. Will contact Maytag today. There are so many complaints. Why not a recall?

Maytag Bravo Quiet 300 dryer(less than a year old): #1, on timed dry setting machine cuts off before the set time, clothes still wet. Needs multiple cycles to achieve drying, then you get wrinkles. Cannot manually set time, its automatic. Technicians (2) have replaced sensors and tinkered with timer, no fix, no documentation to show what was actually done.

We purchased a MAYTAG refrigerator when we recently built our present home. This refrigerator has been a nightmare! Ice forms in the bottom freezer and then constantly melts out of the bottom of the appliance all over the floor. Weve had a number of service calls with no real effect. The computerized function that sets functions do not work well and often shut down the appliance with little clear way to start it up again. The ice maker/dispenser often clogs up or will not produce ice. Weve had it! We broke down today and spent the money on a new GE refrigerator. My very strong advice is DONT BUY A MAYTAG refrigerator with the freezer on the bottom!

We bought a Maytag dishwasher 4 years ago, we had to have it serviced a few months after purchase for the soap & rinse agent dispenser not working, then a few months after warranty was up the buttons on machine wouldnt work, the control panel failed so we had to pay for a new one and install it... Well last night exactly one year from the install of the new control panel I walked into my kitchen to find it full of smoke and the dishwasher pour out smoke, when my husband came home he took the door off and sure enough the control panel was burnt and melted! Very scary. It is a very good thing I was home and this is why I never leave appliances running if I am not home.