Ive had the dishwasher model MDBH979SAB0 for about 3 years now. A few months ago I noticed the faceplate would pop out when you opened the dishwasher. I would have to pop it back in. The dishwasher was out of warranty so I decided to attempt to fix it. I took the faceplate off to realize all of the plastic tabs that screws go in to were snapped off. The only fix for this is a complete new panel from Whirlpool Parts Online to the tune of $194.17 (W10811169).The wheels also fall off the bottom rack. The push pin plastic becomes brittle over time and does not stay in the assembly. To replace the wheel assembly (there are 4 in total) is $38.18 each (W10195416V). The wheels or push pins cant be purchased separately. Both of these items are not covered under warranty past 1 year. Maytags 10 year warranty only covers the upper and Lower Racks (excludes cup shelf and silverware basket), chopper blade and stainless steel tub and inner door liner. So only a small percentage of the parts.The design of the faceplate is defective in that too much force is applied to the faceplate when opening the unit. The handle is integrated in to the faceplate. The plastic used becomes brittle over time and breaks. The panel unit (W10811169) must be replaced in entirety rather than just its housing increasing the cost of repair. To have this failure occur within the first 3 years of use is very premature. I can only assume if I repair the dishwasher I will have the same problem again. I am considering buying a new model that is designed better and comes with a longer warranty on such parts.

We bought a Maytag dishwasher in May of last year. The control panel went out about 3 months after we got it. It just started doing its own thing Like not running the wash cycle or a different cycle than we pushed. We called for a repair and were told by the repair man that the control panel was on the fritz. He ordered a new one and told us it would be a month before he could come back and install it. When the control panel showed up at our house, we installed it ourselves because we did not want to have a faulty dishwasher running in the house.Just yesterday we noticed a huge rusty area on the bottom rack. We called and were hold for 20 minutes if not more, before we were even able to talk to a rep. She then came up with every excuse as to why our rack was rusty (hard water, water changing??). We asked for a new rack but she wanted to send a repair kit. We were on the phone with her for half an hour, if not more, and she just refused to send a new rack. When we finally asked to speak to the manager we were told the wait time was 32 minutes and hung up! Do not buy crappy Maytag appliances with even crappier customer service reps! (see our review about our Maytag fridge!).

My Maytag washer and dryer (5000 Series) is about 2 years old. Just as soon as the warranty ran out, I started getting F35 and suds error messages. Information found on the internet tells me that many Maytag customers have experienced the same problem. Whats up with this Maytag? Since many of your customers have experienced the same problems, are you willing to meet the consumer in the middle by repairing the product at no cost or are you building the appliances to last as long as the warranty?

I purchased a Maytag Centennial Top Load Washer in February 2012. I wish I had understood the workings of the washer before making the purchase. I am not at all happy that the lid locks as soon as the washer starts and unless I push a button to get the lid open. I cannot open the lid to maybe add more items or check to see if the water amount is sufficient or too much. I have no idea how much goes in for each water level. Of course, I cannot take water out but I could put more in if I see it is not enough. And after learning the water levels, I would know just how to determine the level I need. Some man must have designed the panel. Otherwise I am satisfied. I really like the large load capacity. I originally thought I wanted a front load to get a large capacity but this suits me fine.

I purchased a Neptune washer/dryer front loader. All Neptune washers have basic design flaw over which the company should be sued. Since the bulk of the weight is in the front of the horizontal wash-drum, the entire assembly is suspended by a rear mounted bearing allowing the drum to spin. That bearing assembly is woefully under-designed and not able to support the unequally distributed weight that is inherent in any front load design.Since the forces of gravity cause a loading of the rear bearing on the front of the bearing raceway only, the machine is doomed to catastrophic failure of the entire drum system--and they all do this. When the washer goes into spin mode, it sounds like a jet engine taking off and that is a symptom of the bearing design beginning to fail which begins on the first use of the machine. The cost of the drum assembly/bearing and the labor is far more expensive than buying a new machine and therefore, not worth it. Avoid Maytag products at all costs.

The dishwasher would not start July 30 2015. Tried to get service around here and no shops could respond. Called Midsouth Distributors for circuit board. They did not have one but would order and gave me the part # W10595570 based on the Model # MDB7749SBW3. Hoping could find one quicker somewhere else. Ordered one overnight from Sears and planned to replace the board by myself. However, I noticed the flat wire with 14 wires in the ribbon cable had brown spots. From my experience in the electrical systems, I realized this must be shorting out the start signal to the dishwasher logic controller. Sure enough, after scraping this off with a sharp knife, I was able to start my dish washer.My previous MAYTAG lasted 20 years. I bought this one in February 2014 at Home Depot. The design for the electrical controls is obviously very poor as testified by so many angry owners. MAYTAG should be required to replace all these control panels with a improved design at their cost. I hope this obvious poor design of a part gets attention in the United States and ConsumerAffairs will help us. I have called 1-800-688-9900 and registered with MAYTAG a complaint about this poor design.

I purchased my Maytag Bravos XL washing machine in July 2016. In August 2016 it broke for the first time. I was just passed my 30 day moneyback guarantee, so Sears would not take the washer back. I have had more than 10 service calls on this washer in one year. I live in a rural area, so Maytag told me I was in a non-serviceable area and would have to wait WEEKS until they found a repair person willing to come to me. I only live 40 miles from Richmond VA, where I purchased the washing machine, so imagine my shock when they told me they couldnt fix it because of my location! Ive had countless people in and out of my house, and it still does not work right. You can only do very small loads, so the perk of having an XL machine is none. But even at that, it does not properly clean anything, tangles clothes, and will leave even the cleanest items looking terrible when they come out.Ive had a new circuit board, new transmission, new bearings and gears, new balancing rods, and still, Im left with a machine that does not wash and makes terrible grinding noises. I bought the washer and matching dryer as a set, and even the dryer had to get a new circuit board put in it in the 1st 60 days! After thousands of dollars in repairs on a $1000 washer, Maytag will not admit I have a defective machine and replace it! I just ran a load of laundry and have to call Maytag yet again, because the grinding noise gets louder with every run. Do not waste your money!I would give anything to have the 29 year old set I gave away when I bought this garbage back! I have literally been on the phone with Maytag in tears because it doesnt work properly, Ive had to throw away items that would not come clean because there is not a laundromat available in the town I live in. All I want is to be able to keep my family in clean clothing and linens, doesnt seem like too much to ask.

I purchased this new Maytag washer (Model # MVWC300XW, Serial # 12621033) from Hahn Appliance Warehouse in Oklahoma City, OK 73107 on November 23, 2011. It is less than six months old, and the transmission has gone out. Hahn advised me that they had to go through Maytag Service, and they would only replace the part. I contacted Maytag/Whirlpool Service Corp. directly and spoke with a manager named David, who informed me he was sorry but would not authorize a refund or exchange for a better product because this was the first service call. I am very dissatisfied with this product and with the service standards that Whirlpool/Maytag offers on their products. If I were to sell a product that I knew has had numerous complaints, I would pull that product from my line offering and make either a full refund or replace with a higher level service product.

Purchased this dishwasher 3 1/2 yrs. ago. Control panel went out. We would have had to pay almost the cost of new one to replace the part! Maytag used to be reliable. The dishwasher we owned previously (not Maytag) was still working after 12 years!

Our first (and last) experience buying anything made by Whirlpool. I bought a matching Maytag Series 2000 washer and dryer in February 2011. By July, the washer was at 747 take-off noise level when hitting the spin cycle. I called Whirlpool, who directed me to their local repair firm. I called them on August 2nd and had a service rep visit on August 9th. He looked a 30-second look and advised that the bearing assembly was shot and that the spin basket required replacing.

I bought the Maytag because of its reputation and as a washer it hasnt disappointed me.. It gets my clothes clean with a minimum amount of effort on my part and it doesnt use a lot of water... I love my washer.

In the past 20 years, we purchased a washer, dryer, stove and dishwasher... all Maytag. The washer (purchased 20 years ago) is still functioning well! The other three appliances have all given us trouble and the dryer is no longer with us. Our stainless stove is LOVELY but thats about all its good for. Within 12 months, one of the burners burned out... just beyond its warranty. It has two ovens and 3 years after purchase, neither will hold a constant oven temp and both take an eternity to warm up... although the digital temp on the oven tells me its toasty warm. Recently, the dishwashers control panel wont set properly. An attempt to set it for a normal wash/dry cycle results in rinse only and a 2 hour delay. Make them like you used to, Maytag! Im no longer a customer!!!

We bought a New Condo, all New Maytag appliances with a 10 yr. warranty, the microwave is a built-in model. I cant believe weve only been here a year and eight months and it just stop working. We use it for heating and short timed cooking like 1 to 2 minutes. I would think a name brand product would last a lot longer than this. I had an off brand microwave for five years before the condo. A couple of times the microwave door didnt close, I thought I forgot to close it. But after reading your reviews I now realize its one of the defects of the product. I called the Maytag company, they informed me that if a serviceman come out to fix it, it will cost me $180 until they can determine if the cause is something covered by their warranty??? The Home Builders bought Maytag junk and passed us the cost, now Maytag wants me to pay to see if their junk can be fixed??? Wow!!! This is unbelievable!

My fiancee and I purchased a Maytag washing machine from our local Sears. We got it home and it worked fine, but after the first month it wasnt switching over from cycle to cycle. We called Sears and they stated that they didnt provide service to the washing machines, so we would have to call Maytag. We called Maytag and they sent servicemen from B & B Appliance to our home. We were told that they needed to order a piece and would be back at another time to fix the washing machine. They came back and said it was fixed. I went to start a load of laundry the following morning and the basement flooded. The hose had become dislodged when they were working on it. To add insult to injury, the washing machine was still broken. I called Maytag to request a different service company come to our home. Maytag said that they couldnt send a different company. They also couldnt replace our still broken washing machine and they could not accept a return. At this point we are out an almost $800 for the washing machine, over $5000 (which we have submitted to insurance) for the damage to our home, and almost $600 for a WORKING washing machine that was a different brand. We will never use Maytag ever again.

I cant warn you enough NOT to buy this design flawed machine. Ive only owned mine two months from Home Depot, the install was a nightmare and now due to a poor design flaw, if you miss loose coins or anything in pockets it will get trapped between the drum and the tub causing rattling and noise during spin cycle. Guess what? Service calls EACH time this happens. This is nothing more than a $750 piece of junk. I feel like its marring the whole feel of my new house. I hate hate hate this washer and am trying to get Home Depot to take it back, Maytag to refund me or sell it at a huge loss. This is NOT getting anything you pay for and I vow to NEVER EVER buy Maytag again.

I purchased the Maytag Washer & Dryer $1891.14 with Extended Warranties Model numbers: MHW5100DW0 & MED5100DWo. In September 2014 from salesman ** at ABC Warehouse for my Wife as a Wedding Gift. The dryer started malfunctioning toward the end of October, it was randomly flashing a red light indicating Check Lint Screen and when this happens the dryer will lock up not allowing you the OPERATOR to dry your clothing. We ALWAYS check our screen before use and clean after each use, so we found that light to be odd. But anyhow we checked the lint screen and nothing was on it nor was it bent out of shape, everything seemed normal to me & my wife besides the fact we spent $1891.14 on BRAND NEW washer & dryer set thats acting weird. I called ABC Warehouse spoke to **. He said Yeah they do that sometimes, you just gotta MAKE SURE YOU BLOW THOSE THINGS OUT MAN cause they dont like it dirty. I explained to him we keep it clean then he said the screen might be slightly bent. He went on to explain how he seen that happen a lot, I just said uh huh uh huh yeah yeah. So now its like the middle of November and the DRYER Check Lint Screen Light is coming on before every load now and staying on for long periods of time not allowing us to dry our clothing. So I called ** again 2nd week of December this time asking for a new unit. He told me to call the ABC Warehouse Store Warranty Department at 1-800-722-3333. I called and they gave me a number to Master Tech Appliance 1919 Federal Blvd, Ann Arbor, MI 48103 (734) 662-0641. I immediately asked why am I calling technicians instead of new unit when my unit is still under the 1yr factory warranty and in addition too, I have purchased an 5yr extended warranty? They wasnt trying to hear that. So I called Whirlpool 1-800-253-1301 told them the situation and asked for a new unit they said NO and then added by telling me their policies and how many times they can come and attempt to fix my unit before replacing it. I screamed and shouted at them explaining to them that I have spent $1891.14 on a non-working unit for my wife as a wedding gift and I am currently drying my clothes at the local Laundry Mat, they said NO still.So I called Master Tech, they couldnt come out until Feb 3, 2015. My wife took off from work. In the mean time it completely stopped working the first week of January, we had to go to the Laundry Mat every couple days cause we got 4 kids. SMH WOW my wife is pissed, I mean furious. When ** from Master Tech showed up he looked at our unit and said its also not getting hot so he called in to his job they told him to come back and order my parts and to schedule another day to come back. 2 weeks later Master Tech called with the appt. My wife took off from work again but this time they called the day of hours into the day to tell us the parts are on back order and they need to reschedule. My wife was VERY UPSET but we did it anyways. Now remind you are dryer is still out of commission. Were going to the LAUNDRY MAT. Master Tech came 3 days later (my wife took off from work) they literally took our dryer apart (Pics Below) for it to still not work, Master Tech called Whirlpool, Whirlpool told them to order us a NEW SWITCH BOARD. Wow what the hell are you serious? So Master Tech leaves again and orders the SWITCH BOARD. They came 5 days later (My wife took off from work) new switchboard and dryer still not working. Now throughout this whole ordeal Ive been in contact with all 3 companies begging for a new unit and nobody wanted to hear that especially WHIRLPOOL & ABC WAREHOUSE. With Whirlpool knowingly the switchboard didnt fix the issue the first time, they instructed Master Tech back to my home with the same but NEW SWITCHBOARD. LOL WOW I CANT BELIEVE THIS IS HAPPENING TO US. Master Tech schedules yet another day to come by 3-13-2015 & yes my wife took off from work AGAIN just to hear ** say sorry they keep sending me back with the same part and they know its not gonna work but anyhow Im here. He switched out the Switch Board again and still nothing. I called ABC Warehouse and they finally okayed us a new dryer with delivery day of next day, which is today 3-14-2015 and when it arrives THE WHOLE FRONT DOOR IS BENT OFF THE HINGE WOW WOW WOW WOW. Now they say our new will be delivered 3-17-2015 and yes my wife has to take off from work.Updated on April 9, 2015: 3/17/15 ABC Warehouse replaced the 1st broken dryer to only return with another broken dryer, same problem, red check screen light flashing & dryer wont spin. They left here.

We purchased a $500.00 Maytag dishwasher, Model #MDB7749SBW, in August 2013. In December 2014, a little over a year of owning it, the pump failed. We called Maytag and they had a service company come out and replace it. We paid $181.00 for this service call. In July 2015, the control panel failed so we called Maytag to see if they would replace it at their cost. All they are willing to do is to send another service guy out at our expense. The service call is $89.95 and that doesnt include the labor! The total with tax will be close to $200.00 again!!! Now we are getting close to spending $1,000 for this piece of junk! In addition, this dishwasher is only used three times a week because there are only two people living in our household. It is obvious after reading the other complaints that the control panels are defective and I am sure that Maytag is well aware of this issue. So, buyer beware. Dont even consider purchasing a Maytag dishwasher unless you enjoy watching your money flush down the toilet. They dont even deserve a 1 star rating!!!

Ive only had my Maytag Bravos XL Washer for two years and I HATE it. It constantly gets off balance during the rinse and spin cycle. What should take 30 minutes takes triple the amount of time. My washer is in the basement and I constantly have to run up and down the steps to readjust the clothes in the washer. Ive started to just stand by the washer now during the rinse and spin cycle. What a waste of time. I would not recommend this washer to anyone. Also, it does an awful job of rinsing out the detergent and softener. All of my dark colored pants have detergent and softener residue on them after they come out of the washer. Ridiculous!

I bought a Maytag dishwasher (Model: MDBH949AWS2) from Home Depot on 07 April 11 and it died 24 August 11. I called Maytag to set up an appointment for repair. The repair person showed up and stated that the control panel needed to be replaced. Apparently, if moisture gets into the panel it shorts it out. One would think that when designing an appliance that utilizes water and creates steam, it would be sealed. Anyway, the repairman explained that because the dishwasher was in a residential program, the warranty was null and void. I wish that someone would have explained this before I purchased it. I went online to AppliancePartsPro.com and ordered the part for $100.75 including the shipping cost. Then, I went back online to look up how to install the panel. The repair person said that they are charging $133.00 for the part and $129.00 to install. A small star tip screwdriver and 15 minutes was all it took to fix. From what I have read, this will not be the last control panel but, at least, I know how to fix it. Another thing that I know is that Maytag is off my list of future appliance purchases regardless of where Im using them.

The refrigerator has been very dependable for over 14 years. The biggest problem we have had is failure of plastic tracks on drawers that break and had to replace drawers and other problems with plastic components like deli drawer coverlet, and door shelf door plastic. Recently we have problems with the touch control panel on front of door. Not working properly for ice dispensing and temp. control although temp is maintaining what we had set prior to failure of control panel.

We bought a heavy duty washer 1 year ago and paid a decent amount of money for it. Had it delivered and installed mid February of 2020. Worked fine until Dec when the lid cracked (which is common said the Maytag repair man), but since it wouldnt lock, we couldnt use the washer. 1 week we were told and it would be in - a month later and over a hundred dollars spent at the laundromat, the part came in. Used the washer for 1 round of laundry - 3 days later all these error codes started and our washer wouldnt work again. 2 weeks this time for the parts and another $100 at the laundromat- a month today and Im told they are on backorder.Called the place we bought it and they said to call Maytag. Call Maytag and they said that they will try to expedite the parts and could offer me a whole $75 for the inconvenience. They will not replace the washer or give me a loaner until the parts are in. 2 months w/o a washer on a 1 person income for a family of 4 and they cant do a single thing to help. If a 10 month old washer needs 3 new parts one of them being a new control panel - within the first year - this is a lemon and should be replaced. I was told they are big on customer service, but obviously Im just a little fish in the ocean and they dont care about me.

Every time I do a load of wash, it comes out looking like I slept in it. It is so wrinkled you cant even iron it all out. If the load gets off balance, you have to wring it out by hand because you cant get it to spin again. I did a load of flannel sheets and it went off balance, wringing sheets out by hand is enough to make a person want to send the machine back and get an old-fashioned wringer washer. I hate this machine without an agitator. I have always used a Maytag washer, but I would not recommend this to anyone.

This Maytag dishwasher works great if you are using as a sanitizer for your dishes so long as the dishes were soaked already. It stinks if you do not use it often and requires a lot of bleaching.

February 2011, I purchased a washer from Lowes and started having problems with the washer leaking and skipping cycles on the first week. Lowes exchanged the washer end of first week. The new washer started with not adding water in wash cycles. The repairmen sent by Maytag could not find any problem with the washer. The washer worked off and on for months with problems. Cycles with bleach added worked fine, but 3 or 4 loads later with no bleach having been added, it would produce bleach-stained clothes. The repairman came out again and could find the cause for skipping cycles, but suggested I run clean cycle every time I use bleach. It defeats the purpose of purchasing an HE water-efficient washer.The third repairman sat and watched the unit run a load and then he said I know what is wrong. He took the washer control panel apart and found the wire harness was not properly connected from tub to control panel. I have not found what causes bleach stains 3 loads after the bleach was put in the washer. I will not recommend this unit to anyone because of manufacturing problems with harness assembly.

I have owned a Maytag washer since 1989 (25 years) that has had absolutely NO PROBLEMS WHATSOEVER. It now has a slight leak, so I am considering replacing it. I contacted an appliance store and advised them of my problem. The salesman made a comment which indeed surprised me. He said that, although he would like to make a sale, I should do everything in my power to keep that old Maytag machine because they dont make them like that any more! From reading the reviews about the new Maytag now I understand why! I do not plan on buying another Maytag, which really saddens me, as they were once a high quality, dependable product.

I built a new home in November of 2013 and filled my house with all brand new top of the line Maytag appliances. Almost a year and a half in, my $2500 refrigerator is broken and all my food is lost. They send a repair man out; and guess what, the warranty is expired. So they wanted me to pay $800+ to have my refrigerator repaired a year and a half after I purchased it. I cant believe they have no shame in sending out products with their name on it that only last 1 1/2 years! I would never treat anyone like they treat their customers. They hold no responsibility. Their name holds no value to me anymore. I was extremely disappointed.

Maytag WFW7590FW & YWED75HEFW 24 Compact Washer and Dryer: These 2 machines are a lemon and the extended warranty plan was completely disappointed. Both needs maintenance before the 1 year warranty ends. The washer was the worst between the pair. The washer cannot spin the laundry dry. The Home Depot extended warranty plan was not the cost. It takes 2 business day for the service call to call us back. Then a schedule date was 2 days later. The service person complained about not getting authorization to do the work without charging us. He did even showed up for the 3rd call. He did nothing to resolve the issue and said the diagnostics showed there was a load issue, which was not true. A very light load still didnt spin dry. The washer not spinning clothing dry issue has been more than 1 month and is still not resolved. The repair person Dean didnt even re-schedule another date after not showing up today. There is a 90 day policy that we cant request for another repair person to attend to the issue. The dryer also made excessive noise which was caused by a broken attachment that established the drum.

We bought the Maytag Bravos XL washer 6 years ago when we moved into a new home. We have a large family and after reading many reviews, we settled on this washer. It has served us well for the past 6 years. At the moment, however, it is out of commission. The bearings wore out. My husband ordered new parts and we hope to have our washer up and running again in a couple of days.

I have a Maytag Precision double oven 850 series. The upper oven handle does not fit snugly and has been broken 4 times. I have had to order 4 new handles because the hardware does not seem to secure the handle to the oven door. There are no problems with the lower oven door.

I am very happy with my washer. It is easy to use and does an outstanding cleaning job. I have had it for almost 7 years and have not had any problems with it. It has many different settings so it can handle virtually any cleaning job. I am particularly happy with the spin speed which is adjustable but the high speed spin really wrings the water out so the dryer which incidentally is also a Maytag drys in a fairly short time. The washer is a front loader and doesn’t use much water.

I bought a Maytag stainless steel refrigerator w/ freezer on the bottom. Since 6 months fridge being in my house I started to have problems, rust on the doors, water coming out of the bottom, freezer door got stuck w/ ice and couldnt be opened, butter, eggs, milk can be frozen one day and the next they have mold and bacteria because of the changes in the cooling system, among my problems. And what? Well yes thank you so much for the guarantee Maytag has in Puerto Rico, IT SUCKS! They been in my house more than 5 times and nobody really says whats wrong. They supposedly change the computer, still having problems, and this was done after more than three times visits from Maytag guarantee. Im still paying for the damn fridge and DO NOT HAVE A RELIABLE REFRIGERATOR. Im wasting too much food, Im obligated to buy food almost every day cause Im scare to give something that may be bad and my family will be food poisoned. Whos going to pay me or my family if something happens. Maytag is still running falsely commercial ads and somebody MUST STOP THEM. This appliances are not free or cheap. PLEASE help us because Ive learned that Im not the only one having problems in Puerto Rico w/ Maytag. Also I believe Maytag is using technicians not ruled by the government of Puerto Rico and thats why the service is horrible.

We are extremely frustrated with this machine. It takes an extremely long time to go through the cycle, compared to past washing machines, even when it is working. It rarely completes the cycle and often goes back to wash and stops. We have no way of knowing if it washed or rinsed or what. To get it to finish, we have to turn the dial to drain and spin. The clothes always come out tightly twisted and tangled up and have to be untwisted and items pulled from each other....so they are extremely wrinkled! This is the first and last Maytag product we will ever buy. We HATE it!!! I would say it has been a lemon from day one but Home Hardware was no help when we complained. We tell everyone to stay away from this product.

I wish I had found this website before I bought my new Maytag washer and dryer from Home Depot on March 7, 2018. I replaced a 30 year old Maytag washer that I should have kept. I wash two loads a week so has not been used that much and now it will not drain. I tried everything, canceled the cycle out, checked the circuit breaker, unplugged it, removed the clothing, bucketed out the excess water, tried the drain and spin cycle, etc. Just will not drain or spin. Repairman is coming next week... Still under first year warranty but if it is not the “fault” of Maytag I was told there will be a $90+ minimum service charge.

This top load machine replaced a top of the line Maytag Neptune. It has five water levels. It has three temperature settings and four wash selections. It also has a selection for an extra rinse that I use for white loads. The washer is very reliable. Clothes come out clean with an average amount of detergent. Although this washer is more than fourteen years old, it has never needed service or repairs. By running a cleaning cycle every six months, it drains like brand new. The stainless steel drum is still as polished as it was when it was new. Even the hoses have lasted with a need for replacement.

Water saver feature is horrible. Never enough water. Doesnt get anything clean, even if you soak it overnight. I am buying a new washer and it wont be a Maytag.

Our brand new Maytag dishwasher model number MDB87749SBM2 was professionally installed on 7/31/2013. In fall of 2015 my control panel started acting up. I was unable to select certain wash cycles. The problem would come and go. By January 2016 my lock button would freeze and I was unable to unlock or select any wash cycles. By February 2016 my control panel went out completely. It wont turn on, not a single light. It is fried.When Googling the issue I found that we are 1 of MANY with faulty control panels not only on our particular model but on many Maytag dishwashers. They all seem to have the same problem, right around to 2-3 year old mark. One would think dishwashers would last, like before. A dishwasher shouldnt need to be replaced or need a major repair so soon. The one our new dishwasher replaced was 12 years old and was working just fine. We just wanted to upgrade to stainless steel. Wow what an upgrade haha! Maytag should be recalling these control panels. Their name is no longer a trusted name in our home.

Lets be real and say that people with good experiences dont often end up on websites writing reviews because they are busy enjoying their product! I purchased my set in early 2012 and will admit that initially there was a learning curve with using a washer with no agitator. I enjoy doing laundry and Im really good at it but with this washer I had to change my routine. Always pretreat stains. Deposit clothes loosely around the drum and shake clothes loose before putting them in the dryer. My clothes come out great! I have a child, two dogs and a greasy truck driver man and everyones clothes smell great. I can wash my king bedspread and anything else in my house with no issues. And my washer has never torn any of my clothing, however fragile. I dont iron often and I hand wash nothing.I give 4 stars instead of five for the extra steps to ensure my clothes are clean and wrinkle free. No they dont make things like they used to but thats with all the new stuff. My moms 3000 dollar Samsung set (her washer) isnt working as I write this. Too bad more people with good experiences dont get online and share. Hope this has been helpful.

HORRIBLE. Dont pay more for substandard machines. Had a Maytag washer and dryer delivered on March 27th 2018 and it has been a nightmare to get it to start up. Now I have clothes stuck in there. I called Home Depot, you should never buy any appliances from them, they wash their hands of all responsibility once you sign for it. Called Maytag. On hold for almost 10 minutes, they only have 2 certified repairmen in the area 0f 600,000 people. Will be 5 days until they come to look at it. I told them I wanted to return it for a GE or something else. They said I had to contact Home Depot yet Home Depot told me it was Maytags problem. SAVE YOUR MONEY!!! MAYTAG IS NOW AN INFERIOR PRODUCT WITH EXTREMELY INFERIOR SERVICE.

This dryer ripped a gaping hole with sharp shards of metal exposed. It was working fine, and then it made a weird noise. It stopped and I assumed my laundry was done. We go to remove clothing and cut hand open on exposed metal. As if that wasnt bad enough, several hundreds of dollars in clothing had cuts in them. This dryer worked great for years, and out of the blue this happened. Im a widowed disabled mother, and cant afford a new dryer.

My refrigerator is a lemon! We bought a Maytag bottom freezer French door refrigerator model #MFD2561HEW in May of 2007. Less than a year later, it stopped working and ruined all the food inside. I cant remember the problem that time, but it was fixed by Maytag and we were reimbursed for a portion of the food we lost. Two years later, the temperature got warm in the refrigerator and freezer sections, and we were gone for a couple of days, so when we got home, all of our food was spoiled. This time we had an extended warranty in effect and they replaced a circuit board, but we were out the food. A few months later, the same thing happened. This time we were home and saved most of the food. The compressor was replaced, again under warranty, but it took 2 weeks to get the part. Now, less than a year later, the freezer and refrigerator compartments are getting too warm and frost is forming in the back of the freezer. When it finally does get cool, it freezes the food in the refrigerator section. It also makes loud bumping sounds. I paid $80 to a repairman today to tell me that theres nothing wrong with it, thats just the way it runs! He suggested I put a gallon of milk jugs filled with water in the freezer to hold the temperature when it starts to rise! This piece of junk is just 5 years old! When I complained, I was told to call Maytag and discuss it with them. This refrigerator was not cheap and I see that many others have had similar problems. How do they get away with selling an inferior product?

Two in a row make it just over a year then the control panel goes out. You call a Maytag repairman and they say the control panel is bad! #1 it should last more than a year and a half. #2 a part shouldnt cost you as much as the darn dishwasher! Do not recommend nor would I ever buy another Maytag.

The Deli drawer randomly falls, shelves in general do not fit well. Rough edges on door corners are a hazard especially for children. Service call line was extremely poor with a total disregard to customer concerns. It has been a very bad decision!

Dishwasher Model MDB7749SBM1 - When I returned home from work today, I noticed the cancel drain button was on and the unit was continuing to try and drain but the dishes were not clean and the cascade pod was still inside the unit unused. I then proceeded to run another cycle to clean the dishes and what happened next simply amazed me. I pressed the jet clean button, tough scrub and 2 hour delay button and thought I was all set but the start/resume button would not engage or light up at all and subsequently the cancel/drain button lit up and the unit started draining. Now the control lock and start/resume button just flashes intermittently and wont disengage. I purchased my unit along with several other new Maytag appliances when I renovated my kitchen. I guess the microwave, stove and refrigerator is next -- unit are only 29 months old. Any assistance will be greatly appreciated. Im in deep ish I guess.

Absolutely the worst washer I have ever had. I have read some of the other reviews, wish I was smarter and checked this out before spending my hard earned money to buy this washer. My washer also is rusting at the top where the bleach goes. I never close the lid when not in use my basement is dry AND I never use bleach??? My clothes come out they are a tangled up mess. When I go to hang them they are partly dry. It isnt as though I stuff the washer NEVER put more than 8 shirts in at a time yet they all come out with dry streaks like that part of the clothing never even got wet. We all know what happens when you leave a tissue in your pocket and it goes through the washer... Well not with this washer the tissue sometimes came out as dry as it went in. HORRIBLE product. I want the old agitator/I SET THE WATER LEVEL type back. It takes forever to get laundry done. They should take these OFF the market and give us poor consumers some cash back.

I purchased the Maytag refrigerator MFF2055DRM on 7/7/16 new. It was suppose to be stainless steel; but now I am seeing rust spots at the top and bottom of the French doors. I clean my refrigeration weekly and find it odd that now it is rusting. Also, I am able to place magnets on the doors - which should not be for stainless steel. In addition, I spend over $100 a year replacing the mandatory filters. I must also place the setting to high to maintain my milk and juices. I must also have to place them in the very back of the refrigeration. I am a single senior and my refrigeration is not overloaded with food; nor am I constantly in and out of the refridge. Not very happy.

Machine is very loud. Clothes do not feel completely clean when wash cycle has finished. I have a sense that not all soap has been removed. Dark clothes have streaks of white residue. Must turn clothes inside out before washing. Very disappointed.

Bought this stove in 2011. 9 months ago I had a 300$ repair for fuses to two out of the five stove top burners. Several days ago the ovens were not lighting and I called for repair again. Well the ignition switch in the lower oven had a frayed wire from the factory which created an issue with the control panel. Today I was quoted 600$ to repair the ignition switch and the main control board. PARTS ONLY. I am not repairing this stove. Called Maytag due to the issue of a defective ignition switch wire and got nowhere. Very poor quality product.

From day one I didnt like how this machine restricted how I can wash my clothing. There is no water volume controller. It is all automatic, which sounded fine in the store, but once I used it I quickly realized it is horrible. I can not add extra laundry or detergent in at the last minute because it says not to open the lid at all once you start the load. The settings are very glitchy. They do not seem consistent. There is a knob for level of soil on the clothing which doesnt seem to do anything at all. Ive had it now for four years and it has only gotten worse. Now I can only use one setting Hand Wash. Try doing a teenage boys clothes in Hand Wash and youll find out quickly that nothing gets clean that way. Oh, and all of the sudden the spin cycles are not working, they spin when they want to but they rarely get rid of the dirty water. Spinning in dirty water does not get clothes clean either. This machine is horrible, hands down, the worst washing machine I have ever owned.

Washer model mvwc200bw1 c43942055 -Worst washing machine ever! The clothes come out all twisted together, I cant even see how the washer works because the lid locks when washing! The sound the washer makes while washing sounds like its barely even washing the clothes! I will never purchase any Maytag products and I wish I could return this one!! So disappointed, Im sticking with Whirlpool!! Plus the clothes dont even get that clean!!

This has nothing to do with the vendor. This is clearly shoddy workmanship on the part of Maytag. I bought this refrigerator in 2005 and already the compressor is gone. So therefore, I have to replace the whole unit.What kind of ** is this? You mean to tell me that you people cant find someone to build a compressor that holds up more than a few years? Why dont you try American made and built.I am disillusioned by the whole industry. Im sure the people at the top could care less.

We purchased the Bravos XL washer just over a year ago. It is being replaced 1/10/2017. Simply put this is the worst product I think I have ever encountered. Extremely noisy wash cycles leave residue on the clothes, clothes do not get wet in some spots. This washer is so noisy you can hear it from outside. What an embarrassment. You have to run the clothes twice first with detergent and again without detergent to remove the residue left over from the first wash cycle (not energy efficient at all). If I could give a minus score like minus 10 I would.

I bought a Maytag Bravos washing machine from Lowes in Ocala in Feb 2017. It broke in March 2017. I was referred to a company called Fields Appliance in Orlando Fl. I scheduled a repair under warranty last Friday between 1-4 pm. No one showed up. No one called. I called and called and nothing. BEWARE.

I purchased a Maytag Top Loader Washer MVWX500XL last May 2011 from Home Depot to replaced our 15-year old GE washing machine. Two weeks ago, it started making horrible noise like a jet engine taking off during spin cycle. I called in the Maytag repairman and was told that the bearing is gone and it will cost $ 493.00 to repair it. He claims that the damage is caused by not using HE detergent exclusively and he refused to leave us a written estimate. We are only three adults in our household and we do our laundry once or twice a week. For this machine to be repaired only after 2 1/2 years of light service and for almost the same cost as a new one, I will never buy another Maytag/Whirlpool products ever again and I will encourage everyone the same.

One baffle broke off in my washer. Very disappointed in this Maytag Model #MHWE201YW00 Serial #HL20102420. I purchased this in Sept 2012. Where the baffle was hooked on had sharp fins sticking out that ruined my 2 small rugs - shredded them.

Purchase in April 2010 on 12/31, motor and computer panel went out, not washing. I do not recommend this dishwasher cost to repair. Too expensive.

The right front heating element works at the high position only. The over doors viewing glass is too fragile. It shattered while positioning the range. Otherwise, there are no other issues with electric range.

We have owned a Maytag Commercial Centennial washer for 4 years and made the mistake of not buying an extended warranty as we thought Maytag was dependable and a reputable company and thought the manufacturers 10 year limited warranty would cover us. Washer would not spin clothes properly, started making loud noises, lid would not always unlock as time went on, and finally it broke and soaked my tile and it ran through my wall into my hall carpet. Called Maytag and was told we didnt have a 10 year limited parts warranty 6 times (we still have the book that says we do), they offered us a 1 year full warranty for $320.00. We purchased the warranty 11/04/16, Called Maytag as no one knew where the parts were and was told service plan is through AIG. AIG couldnt tell us where the parts were either and when I asked for our refund and we just buy a new washer they advised me they would have to prorate it.Now I feel held hostage. Parts finally come in and Maytag Certified repair man comes to repair machine on 11/30/16, only to be told they could not fix our washer as the screws and transmission rotted and fused to tub. Call Maytag as this should be under my warranty and everyone insists I dont have a warranty. Filed complaint 11/30/16, they sent me a survey on 12/2/16 and I filed my complaint again on the survey. No call from Maytag. Call back on 12/06/16 to be told the survey was them closing my complaint. Now they escalate my complaint and will be called in 48 hours and give me an email address to email my pictures of my warranty. Surprise no call back, so I called them again 12/08/16 and I am advised it takes 3-5 business days. Ask for supervisor and he told me even if I have warranty they will only cover the basket.I will have to pay for technician, and other parts. Still no info on my complaint and you cant talk to anyone just have to wait. I emailed Jeff Fettig CEO of Whirlpool (Whirlpool owns Maytag) as well on 12/6/16 a copy of my complaint with pictures of warranty. The bottom line is Maytag sells junk and their customer service is worse than their product. After being without a washing machine since 11/04/16 we will be buying something Whirlpool does not own which is very limited which is why they can get away with making junk.

We have owned a number of dishwashers, some cost a great deal and some were inexpensive. Our current dishwasher is a Maytag and it has proven itself to be the best dishwasher we have ever owned, not only is it quiet, it cost less to operate and cleans all dishes and utensils excellently.

Part on fridge is defective. They have sent the part but tell me they dont have anyone in the area to work on it. Nor will they pay for someone to come out. We must replace it ourselves. This product should be on recall. Maytag fridge. Freezer door on bottom filling up with water. We have 2 of them doing this. One about 15 years old. Other one is 3 yrs old. Maytag knows of the problem but wont fix it. Wont recall their default product.

We purchased our Maytag dishwasher less than a year ago and are very disappointed with the poorly designed quality of this product. We had a Maytag repairman look at our dishwasher and he told us that; the dishwasher cleans with enzymes in the dishwasher not water pressure, and we need to make sure the water in the kitchen faucet need to be hot before starting the dishwasher, we also need detergent, rinse aid, and citric acid added to each load. Adding all these products to the dishwasher does not fix a poorly designed product. This product does not clean the dishes, even with rinse aid the glasses come out cloudy. The dishwasher has a power blast button, it does not clean the dishes any better than the regular setting and it runs for four hours. We will never buy another Maytag product.

Bravos XL Washer and Dryer (Maytag) is the worst appliance set ever. Not enough water in the bin, residue despite using the correct detergent, and clothes which do not even get fully wet during the wash cycle. I am so sorry I purchased this pair - I do like the heavy duty spin, and the dryer does dry (but the door clasp has somehow come loose and stopped working - has to be wiggled into place every time I close the door). The really frustrating part is the low water levels (and even bulky is less than a half a bin of water. I am attaching a photo with two sets of sheets, a towel and three wash cloths). Most cycles only put about two inches of water in the bin - appalling. And the long long long cycles - what is energy-saving about having to do a load twice and using more than an hour for one cycle? I wish I could adjust the water levels. Seriously disappointed in this duo. Sorry I wasted my hard-earned money on it. I was seduced by a pretty exterior.

I purchased a Maytag top load HE Bravo 700 3 yrs ago. I only wash 3 loads of laundry a week and the bearings went bad in the washer! Maytag/Whirlpool will do nothing to help me because they say I should have purchased the extended warranty. Well there is NO WAY that I could have worn out those bearings; it was a manufacturing defect that caused them to fail and hundreds of people online all say they have the same issue. The repair cost is $400 and would only have a 90-day warranty so I might as well purchase a new washer. Home Depot (where I purchased the washer) has been very helpful and is offering me help on the purchase of a new washer, but even they could not get Maytag to do the right thing and repair my Bravo. I am going back to a none HE machine with an agitator. This has been a horrible experience and Maytag has no business putting commercials on TV that say they are dependable.

Our front load washer is two weeks past the one year warranty and need $650 in repairs! I will never purchase a Maytag product again. My last Maytag was 19 years old when we got this new front loader for energy efficiency. You dont save money when you have to replace it after one year.

I have always bought Maytag and never had a problem except with this new washer. Our clothes smell like dirty laundry and when done washing there is lint in the creases or folds of the clothes. I am using a product for cleaning the washer each month, but our clothes still have an odor. I do not like the way the washer works, it just moves back and forth slowly, but the clothes dont circulate enough.

Purchased new Maytag Refrigerator from Mannys in Western MA. Top freezer, over $900.00. Never has worked correctly. We need to turn the freezer way up to freeze the ice cream and it forms frost all around the freezer with mini icicles hanging! But even worse... no matter what setting you put the refrigerator on it ruins your food by freezing everything. The only safe spot is in the deli drawer. I have thrown away hundreds of dollars worth of food that is destroyed because it froze in the refrigerator.A service man from Mannys came and ordered parts. He came back and said they were the wrong parts. Now he says that the refrigerator has a problem and Maytag is trying to come out with a plan on how to fix it. I talked with Maytag (took 44 minutes to get someone on the phone). The manager in service was rude, said they dont replace food and they would work on fixing it. 2 weeks later... no calls from either place. I called Mannys and they said they should have some news by next week. In the meantime I dont have a refrigerator that works! NEVER BUY A MAYTAG REFRIGERATOR!!! It is still under warranty and I asked for a new refrigerator... both Mannys and Maytag said no way.

I love the way it can really handle large loads. The dryer is the best though. It actually dries your load without you having to turn it on more. There are many different choices that handle drying. So, no more to the bone drying.

I sold my 20 year old Maytag set and upgraded to this Maytag Bravos washer. This machine takes almost 1 hour to do a load and they come out dirty. Only way to get clean is to set on bulky sheet which uses twice as much water as old machine. This unit should have never been put on the market.

I purchased a Maytag stove model mer7765wb in December 2011. Now its November 2014. My display board caught on fire and its burn out. How can a Maytag product go out within 3yrs. I purchased it from Sears outlet. As Sears customer I am very disappointed in this product. Thank God I was in the kitchen to put out the fire.

I have a Maytag dishwasher and the rollers for the racks are failing due to heat: plastic wheels breaking up. $35 each to buy and replace. There are eight total. So $280 because of poor testing and quality of materials. Manufacturers should test to ensure the parts last a reasonable period of time and are designed for the environment in which they are being used.

We bought our Maytag Neptune washer in 2005. We chose Maytag because of their reputation, their headquarters in Michigan, and because looking at the machines in the store, they seemed to be well built. Were we ever wrong! You would think paying $1000 for a machine would get you a product that lasts longer than 8 years! Our other washer (a Whirlpool) lasted 20 years and was still working. Im now consistently getting a 3e error code. In searching online, I found that this is a pretty universal problem and thought maybe Maytag had a recall on it. What a waste of valuable time. I did find out the machine was actually a Samsung. This seems like fraud. If I wanted a Samsung, thats what I would have purchased! Contacting Maytag Customer Service was like Land of the Stupid. After getting the runaround and being sent to a phone number and website that only covered Samsung I called Maytag again. I was put in contact with another person who could supposedly help me with the recall. Even though I told him what the problem was, he gave me the robot response about sending the GFCI plugin and told me, That should make your washer safe to operate. Seriously??? I replied, This wont fix the problem because THE WASHER DOESNT WORK and we got the recall part long ago. He then wanted to schedule a repair appointment. Not doing that, considering how stupid the Maytag reps I had talked to so far had been. Putting the hubby on the case, luckily hes pretty handy. On the upside, it was fun responding to the Maytag customer service survey that night, LOL. All of our other appliances are Maytag and they have all been great, but this washer is an unreliable piece of junk.

We have had this dishwasher [Model MDB7749SBW2] for about 1 1/2 years now, and gave had a lot of trouble with it. It will run a cycle on its own without anyone even touching a button. My current problem is the start button wont work. I reset the dishwasher by pushing the series of buttons I found online to do a reset, and the start light lit up, but after the reset cycle was finished I tried to run a wash cycle and couldnt get the start button to do anything. Ive seen a lot of reviews online on this being common with Maytag brand dishwashers this old. I will NEVER buy a Maytag product again nor would I recommend it to anyone as a good product. I am very frustrated and disappointed in Maytag!!!

I purchased a matching set of Maytag Neptune washer and dryer about 6 years ago and the washer is junk! It sounds like a jet is landing in the laundry room. The repair man said it is not worth fixing - bad bearing. I am not happy!

Bought a Maytag dishwasher (Model #MDBH979SAM0) three years ago. Four weeks ago the control panel wouldnt work correctly. No matter what cycle I attempted to select, other cycle buttons lit up. The start button did not light and the cancel button would not turn off. I called a repair guy, he came out and said Maytag was having a lot of problems with the control panels. He reset the machine and finally got it working again. He said he wasnt able to get a new control panel from Maytag due to demand/delay in manufacturing. Today the control panel went out again. Based on all the other reviews Im not sure its feasible to put more money in this machine. Ill research other dishwashers and get one that has a better performance record. DO NOT BUY A MAYTAG.

We purchased our Maytag Elite dryer almost a year ago. Began to have problems with it several weeks ago. We first tried to correct the problem through the store where we purchased it. After three failed service repair visits the technician recommended we call Maytag directly. We did. Another service appointment was set up. The repair guy determined there was nothing wrong with our dryer (?? It wasnt drying on one of the heat settings!!) but said he would come back and replace the front sensors anyway. After he left I called Maytag again. Explained why I was frustrated. I was told that since the repair guy said nothing was wrong with the dryer there was nothing further they could do for me. Further attempts at repair had to be at my expense. I was incredulous to say the least. The dryer doesnt function properly on the normal heat setting, but because the repair guy cant find the cause I am therefore just out of luck?I will never, ever purchase another Maytag product. I am shocked that they will not stand behind a product that is still under warranty. After only 11 months of use I am stuck with a dryer that will only dry on high heat?! How can a single service visit by their repair guy (whom is on their payroll) be the final say? No second opinion? Is he infallible? Simply unbelievable.

My Maytag washer is only three years old and the control panel completely went. Not only did it cost me the service call, they want $360 to replace the control panel. I called Maytag/Whirlpool to see if they would help with the cost of the part. I am 60 years old and the only one who uses the washing machine. It is not beat up. Maytag would not offer any solution at all and refused to even pay for any part of the control panel. They said it was really my tough luck for not having bought the extended warranty. When you spend so much for an appliance, you do not expect it to only last three years and you should not need an extended warranty. I am so disappointed and I will never buy a Maytag or anything from its parent company Whirlpool.

Purchased a new set of Maytag Bravos appliances in 2010. Washer lasted 3 years -- had a failed bearing and repairman said not worth fixing as tub would most likely also need to be replaced. Replaced with a new Speed Queen which has been operating trouble-free. Today dryer quit heating -- repair person stated it needs a new board -- not worth it to me. I am off to now purchase a new Speed Queen dryer. What happened to Maytag quality???

We purchased the washer and dryer in June 2009. This past weekend, I noticed that the washer was leaking. The price to fix it is half of what a new machine will cost. I am very disappointed in Maytag. When I purchased the machines, I thought I was purchasing a quality product. Ive had paid much less for washers that last longer. Needless to say, I am shopping for another washer this week and it will not be a Maytag or Whirlpool. They are pieces of junk!

My first job was at Sears but went elsewhere to buy Maytag. I have had only 3 sets of washer/Dryer in 50 years. The set I have now are over 20 years old! I am looking at a Maytag refrigerator now.

Because the design is bad, the refrigerator has to be defrosted once a month. A home filled with Maytag appliances, these are all 4 years old and ready for the trash. Dont buy Maytag, it is crap. They sell for money, not workability. The name has been trashed by Whirlpool. I am a builder and they will not ever see me recommend them, not even to a neighbor I dont like.

We purchased kitchen appliances in 2012. A Maytag French door fridge, dishwasher and double oven range. So far my lights on the range have not functioned right as to which eye is on on the smooth top range, the ice maker burned out and now the control panel on the dishwasher has burned out. All of course are out of warranty. We have replaced the ice maker. Now in search of the control panel for the dishwasher. Havent priced the part for the range yet. I do know that I have a Maytag washer and dryer that so far are between 10-15 yrs old and knock on wood they work great. But I will NEVER buy appliances with the name Maytag on them again. So sad that you spend top$$$ for 1-2 yrs of the appliances working correctly.

I bought a new smart washer and dryer from Maytag in mid-2019. Beginning in the first few weeks the machine did not perform as expected--cut off in middle of cycle, door failed to unlock at end of a cycle, constant error messages that made no sense (power failure when power didnt fail, codes that arent defined in the owners manual). To make a long story short, the company that does their warranty repair, which has worked on the machine approximately 8 times, tells me there is nothing else they can do, the machine is a lemon. But their customer service department refuses to replace it. They say it must be repaired, yet again. But the parts are out of stock (which should be a pretty good indication that theres a problem with product quality). So I am to wait. How long? They dont know. Call again tomorrow.Do NOT buy a Maytag appliance. Customer service does not stand behind their products and the products are no longer up to the quality I had previously expected from Maytag. Additionally, telephone wait times on the customer experience line can exceed an hour and are customarily over 30 minutes. Never had an experience like this with any other major appliance customer service department.

I read some of the reviews on the Maytag ovens. I too have the same problems! Have had control panel replaced and still have to set at 400 if I need to bake at 350. It also takes forever to preheat. Trust this review because I am one very unhappy consumer!! DO NOT buy Maytag!!

I purchased the Maytag 6.5 inch electric convection oven about 2 years ago. I wish I hadnt. The oven temp is way off, it cooks unevenly, the back burners hardly work, and the back burners on the stove top barely work, the knobs get stuck constantly, the self cleaning does not work, and the glass part of the door allows dust to get trapped in the glass. The range is $800+ piece of junk, best used at the scrap yard. Today, I turn my oven on, and the element underneath the oven pan caught on fire. Now its broken in half, and needs to be replaced. I look up the QR code, and come to find out the oven is actually a Whirlpool, with Maytag labels on the outside. I would have never purchased this range if I knew it was a Whirlpool. I have always had issues with Whirlpool appliances. This is a fraudulent product, and deceives the customer. Why sell it as a Maytag, when its really a Whirlpool? It should at least state that fact on the description, and salespeople should advise the customer. Now I know why its a piece of junk, because its a WHIRLPOOL!!! I will never buy a Maytag or Whirlpool product ever again. I have always stuck with Maytag appliances. Every appliance in my house is a Maytag, or are they Whirlpool?

Bought va washer. Trying to upgrade. Water fills about 1/3 of way even on bulky setting. Supposed to be high efficiency. Detergent does not get all the way out because there is no enough water. Have to put it through 2 rinse cycles. Worst machine. Design is flawed. Clothes all wrinkled. I cant afford to buy clothes and have them ruined. Man must have designed. Hate the washer. Im poor and they want take it back... want my money back. I cant buy washer every day. I will keep on complaining. No customer service. People just put you off. It is a Centennial high efficiency. A piece of junk.

First I do like the fact that it spins at such a high speed that the water is mostly gone, and that is the good news. I do like that it uses less water but when washing any dark colored clothes there are dirt or scum like marks where the clothes may have been folded or twisted in knots which I also do not like. I have cleaned machine but this started when new. Drying doesnt get rid of those scum marks either. I never had this problem with my old full fill machine. I have used more detergent and less HE of course in both liquid and powder. Any suggestions?

We bought this stove in 2014. One knob got stuck while my teenager was cooking food on the gas stove. He called me at work worried because he couldnt turn it off. My husband left work right away to go home. We thought it was just a bad plastic knob. Now a second knob is stuck in the on low position. There is a third knob that feels hard to turn. That will be 3 burners. This is ridiculous. Its a safety hazard. We consumers have to worry if the house will burn down, get CO2 in the air, and if our family and children are safe. We thought Maytag was a good appliance. I will not buy another Maytag. They should recall this stove top/oven. I have read so many of the same complaint on this website as well as online in general. I cant believe they continue to sell this with this much of a safety issue. Please take it off the market.

We are a family of nine so I wash a lot of laundry. We bought this washing machine a month ago and hoped it would perform like our prior one. The problems are many. It is too smart for its own good- it requires a cleaning after every 30 washes but gives you zero warning beforehand so you will already have the clothes in and started the cycle when it will stop the cycle saying it needs cleaned. There is nothing you can do to override the cleaning cycle, so you are forced to remove your sopping wet clothes and run the cleaning cycle- wasting time and money on precious water! It also wants you to use its specialty affresh to clean it with, adding cost we hadnt planned on. Then you cant tell when to put the clothes in as it tells you to start the washer and then add the clothes, but if you put the clothes in first sometimes it wont start because it wont sense properly, and if you start it without the clothes. Then when you stop to add the clothes it wont start it with the clothes in it- which way does the machine want it?! So it is a guessing game as if the washing cycle will even start. And the washer wont hold as many clothes as our last one did. If there are too many clothes, the cycle will stop and it will refuse to wash until some are removed. Whenever there is a problem starting, which in one month has been four times now for us, it is a huge guessing game as to what is wrong for why it wont start. I dont need this kind of frustration! Further, the locking mechanism in the washer is plastic, and I know from experience that plastic parts will be the first to break. Had I realized this before purchasing, I would have looked for a metal locking device. My guess is when it does break, the whole washer will break. Also, from day one, it has made a sound that Im not sure is normal. It sounds almost like grinding gears every time each various phase starts or stops (washing, rinsing, draining, etc.). I sincerely hope this isnt a manufacturer defect as we didnt buy the extended warranty. We researched this model before buying and many were happy with it but I hate this washer! I loved my last Samsung washer but it rusted all over after just five and a half years even though it still worked great, so I didnt want to buy Samsung again so we took a chance with this Maytag. I am regretting this purchase. I consider myself to be a person easy to please. I want a washer that works that wont rust that you can put a ton of clothes in and throw it in the wash and forget about it. I dont want all this high-tech sensing stuff that just messes up and is highly inaccurate in what it senses! Why cant companies offer a simple, high quality product anymore that works, without the added costly features?! The model number is: MVW6230HW0. Avoid this model number.

Christmas sale, needed a washer. Had a great experience with Whirlpool Duet so went for the on Sale Maytag Bravo MCT. No agitator which I thought odd. Bought the warranty. Did no good as soon as I hauled the washer home (3-hr trip one way). It wasnt washing my clothes clean. Hubby said try different cycles and soap and temperatures but at 8 months pregnant it wasnt long when I didnt fight with the machine but focused on a very busy life. Baby number 7 and I didnt care how the clothes washed as long as they didnt stink. Well baby is older, the warranty is not over and after much dialoging, no one will do anything for me. I put muddy pants in, they come out muddy. I put cloth diapers in, they come out smelling like pee. How hard can it be to come up with a machine that just turns clothes round and round with a little soap and water? Apparently really hard as Maytag failed to test this machine. Maybe city folk just have lightly soiled but on the farm with 7 kids, my kids play hard and their clothes are very dirty. They continue to stay dirty unless I wash them twice on Power Wash and Extra Heavy Load. Not impressed. Would like a replacement washer of equal or lesser value, anything that works. Oh P.S. I have the receipts and order number. Sorry its not put online to be verified buyer but dont feel like digging for paperwork at the moment.

WOW! I cant believe I bought a Maytag MDB7749AWM1 Dishwasher without reading any reviews. Paid $650 for it a couple of years ago and the control panel is bad. $390 to repair it, unbelievable! Sounds like Maytag has a major customer service problem because I will NEVER BUY A MAYTAG DISHWASHER again! Spent $5000 grand on new Maytag appliances thinking they were the best to replace the outdated ones. Not the same, not sure what youre doing Maytag but youre losing a lot of loyal customers. What a shame! My old dishwasher lasted over 18 years and I didnt have any problems. 2 years? Come on!!! Same problem as the other 5000 people, someone needs a career change!

Two years ago I purchased a Maytag commercial technology top-load washer. It only two options for water level, either deep water or Auto sensor. Because I live alone I have very small amounts of clothing to wash at a time. Therefore I was excited about the auto sense to save water. However when using the auto sensor theres such a small amount of water in the drum it does not cover the clothes being washed and often I have items of clothing come out of the wash cycle and rinse cycle with dry spots on them yet. The clothes dont get clean and begin to smell stale shortly after theyve been washed. I contacted the business from which I purchased the machine and they were not able nor willing to do anything about my dissatisfaction. This is the worst Appliance I have ever purchased in my 64 years hows life. I hate this washer. It is totally ineffective. And now Im stuck with it and dirty clothes.

I have had and worked on many washing machines over the years. The worst design and complete failure of parts to easily align in Maytag front end washers is nothing short of staggering. Creating a tension wire to wrap a rubber seal that requires Hercules to install and easily tears the rubber is beyond ridiculous. Avoid front end Maytag washing machines like the plague since they may cause it given the mold and growth from excessive moisture when the seals tear.

Maytag Free Standing 30-inch Gas Range - In 2004 we bought our model MGR5775QDS gas range with 5-burners because it offered the most BTU variety for the price: 1 burner with a high BTU (16K), 1 with low (5K), plus 2 in mid-range (9.5K) and 1 with 12K. Within half a year of using the oven, we turned on the self-cleaning function. Big mistake. One cleaning cycle later, our oven refused to ignite. The cleaning cycle burned out the ignition unit. Cant remember if its replacement then was under warranty but the repairman said this was a COMMON PROBLEM with Maytag and we best not use it EVER. In 2014 our cleaning lady mistakenly thinking she was doing us a favor, set the self-cleaning function. Once again, the ignition unit was destroyed. This time its replacement was $350 with part and labor. One and half months later, the oven is again non-functioning. This time our repair guy said the part is a very minor, inexpensive one BUT MAYTAG IS NO LONGER MAKING IT!!! The only way well get our oven back is if he can find another model and cannibalize it to fix ours. Are we disgruntled? Yes. Would we like to see a class action suit against Maytag for knowingly manufacturing a gas range with a malfunctioning self-cleaning unit that destroys oven parts? Yes. Will we ever again buy Maytag? Not on your life. A once stellar manufacturer gone down the tubes with a growing reputation for making junk. American-made appliances mean zip these days. Thank you for nothing, Maytag.

The digital display on our Maytag Washer model MVWB765FW, bought 3/22/2017, failed overnight (whilst the machine was not operating) after 3 1/2 years. A reputable firm came out and diagnosed the problem, their report concluded that the Control Board had failed and needed replacing: they provided a verbal quote of $525 [ ! ] to do that. The machine cost $600 and based on the expected life for washers (per Consumer Reports) of ten years would have a maximum residual value of $420 based on straight-line depreciation. The retailer from whom we bought the washer told us that he had contacted Maytag and asked them what they were prepared to do about this failure: a week later and absolutely no response from the manufacturer. Apparently Maytag has no concern for their customers or their own reputation. We made the mistake of buying this machine based on Maytag’s reputation and a ten year warranty which appears to cover only parts unlikely to fail! NO MORE MAYTAGS FOR US.

Every appliance in my kitchen is Maytag. I went with Maytag because its made in America and now Im annoyed. The microwave died after about 5 years and since I had a spare, I have yet to repair it. I am just now removing the panel to see whats going on in the inside so I can replace whatever broken part is broken. The double oven I have Ive had to repair twice. Once I had to replace a capacitor on the board because it blew. It cost me zero to replace it as I have an old home theater system I part out. The next item was the control pad itself which I tried to repair but had to replace for $200. The dishwasher died after 6 years of use and after replacing the control pad (couldnt be repaired), it still didnt work. And I got a replacement from my wifes dad who was moving and had to get rid of his. Ultimate timing. I purchased a Maytag refrigerator instead of a Samsung like an idiot (which I suppose I am at this point). The fridge leaks water because the drain plug is jammed and it will take a lot of work to get back there to unjam it. I think Maytag wants to sell you expensive parts that are doomed to break after a couple years of normal use. They want to send repair guys out to your house to charge you to fix their junk. I cant wait to move and buy all Samsung products and do away with this Maytag relationship once and for all.

We had perfectly working 20 year old top loading white Whirlpools w/ an agitator, when we remodeled our home and wanted new pretty grey appliances and decided to donate our machines to the church. I chose Maytag top loading due to their former reputation we experienced with dishwashers, etc. It had an agitator, deep fill option, extra rinse, etc. The sales person at Home Depot stated, the agitator is because people like you still want the agitator, and the deep fill will give you the water you have been used to. Not so at all!!Clothes get wound up together, even with filling the wash tub in bundles, there is almost NO water to thoroughly clean & the rinse cycle is a joke. Clothes do NOT come out clean. Im 58 yrs. old and have been doing laundry since I was 13 so I know what I am doing. Its just my husband and I now, and he is so upset that his clothes are pilling probably from rubbing together, even though I occasionally use laundry bags. I seriously wish I would have saved my money and kept the 2 perfectly working whirlpool units I had. This has been such a disappointment. I sincerely would not buy these.P.S. Weve had service out at least 5 times in the last year, and all they do is test the washer and tell us its working as intended... The last thing that is going to happen is we are going to get refunded for a different set, even though we were educated over and over what it would do by Home Depot associates. We are heartbroken. Maytag is going to lose their former reputation on these washers a dryers :( There is simply not enough water to clean or rinse things!

I have owned my Bravos XL for over a year. Loads of wash have come out with rust marks. These marks do not show up on all items, only one article of clothing/sheet/towel seems to pick up the rust marks (usually a couple of dots near each other surrounded by a circle). They are always the same. They have shown up on sheets which were washed in a white cycle and on other clothes of various colors.I have ruined numerous new clothes and must accept the fact that these random but frequent rust-colored dots are part of my life. I expected more. Im getting ready to purchase a W/D for our home up North and believe its necessary to return to a basic model, probably a GE. Maytag seems to have jumped the gun on this one… putting new product out there, aware these unresolved issues remain.

Maytag dishwasher, MDB4651AWW was purchased on 15/02/2010. Touch panel was replaced under warranty on 16/08/2010. Touch panel became defective on 04/07/2012. It was $103 for the service call: panel was not replaced (too costly, > $200). My 2-year old dishwasher is now useless. The touch panel on this model has failed twice in two years and is obviously a design failure. I would ask for a free replacement panel.

I purchased a Maytag model no. MDBH979AWB dishwasher on 4/28/2010, and I did not take out the extended warranty. I thought a Maytag product was built to last, but according to Maytag, I am wrong because they only offer a 1-year warranty on their products. About 2 months ago the hi-temp button on the control panel stopped working. Then a few days ago, the START button stopped working, I emailed Maytag and they sent me a PDF file that shows the warranty is only 1 year. I purchased the dishwasher at Home Depot, I went there and talked to customer service, they were no help either.I am very disappointed in both Maytag and Home Depot for selling products that Are CRAP! I paid $499 for this dishwasher, and if I would have known it only came with a 1-year warranty I would not have purchased it. I will no longer purchase any products that are made by Maytag or any products associated with Maytag.

This product has been a huge disappointment, from day one. It wrinkles and tears clothes beyond recognition. When I called Maytag to complain, they tried to up sell me a service contact. I explained that it works fine, as a shredder, but it is just a bad design and asked if Maytag had any recalls. He then told me if I purchase the service agreement and they cant fix it then they will refund the $$... ITS NOT BROKEN. It was crap when we got it home. Shame on me for not taking it right back to Best Buy. Someone needs to start a CLASS ACTION SUIT. I am sure they have duped many people into buying this shredding machine...

I’ve had my dishwasher for over 10 yrs now and I probably need to upgrade but it suits us just fine and I’ve really never had any problem with it at all. My dishes and especially my glasses come out Sparkling.