So wife and I purchased a Maytag dishwasher in late 2012. A year and a month later it turns into Hal 9000 from 2001 Space Odyssey. I press normal, it shows light rinse. I press heated dry, it tries turning off the life support and blowing me out the air lock. Finally, in March it dies. No power, no nothing. $500+ for an appliance that lasts 2 years. So for the past few months, while we wavered over buying a new brand or spending $250+ on a repair, we were washing dishes by hand. It was as bad as my grandma used to say it was. Then, by chance I ran across a web blog talking about this being a common problem, and there are hundreds of complaints, and its a problem with a $4.00 part on the control panel that can be fixed with a Q-tip, rubbing alcohol, and silicone... Im not a handyman by any stretch of the imagination, but even this I could do. Unplug or switch off the breaker. After unscrewing all the screws, (not your standard or Phillips head either) unplug the control panel from the control box and remove the control panel. On the back, youll notice a flat cable (pictured below) that will have dark marks on the opposite side of the part sticker. Gently clean this with a Q-tip and rubbing alcohol. I then covered the back (side without sticker) with silicone, (you can get at hardware store or Target) let dry, and put everything back together again and now its working better than new. Im regarded as a master handyman in my house, and I didnt even have to hear the dishwasher sing Daisy Bell as I disconnected it. With such a simple fix, Im amazed Maytag didnt just own up to it and get it addressed. The millions it will end up costing them in the long run, by this frustrating experience shared by us all will have them thinking twice in the future (hopefully). It is a shame they seem to be adopting the business model of American auto manufacturers of the late 80s. Ill update this in a year and a month to let you know how the fix worked, and you owe me a beer for saving you $150 - $600 for a repair or replacement. One word... VICTORIOUS!!

I bought a full Maytag kitchen in 2010 because like many others, I trusted the brand. However, before I knew it, the dishwasher broke down. I live in Canada so I get Whirlpool (owns Maytag) 2 year limited warranty. Thank God for that because I have had the repair guy come 7 times. Each time for the same problem (control board) and they have replaced a listed of parts with no success. I have asked them to honor their no lemon policy but am given excuses as to why someone has to come see it first before they can give me a new one. Once the service guy arrived he obviously has no idea about anything and just goes for the repair. Its so frustrating.I am fed up. It is completely unacceptable because now Im losing money staying home waiting for the repair guy. Maytag is the biggest piece of junk I have ever bought. I only hope you see this before buying a Maytag product. Like many others here I use my dishwashers once a week. Now Im faced with a dilemma where I might have to purchase a new dishwasher as soon as my 2 year warranty runs out. My $700 went down the drain.

I purchased my Maytag Bravos washing machine set in July 2007. In May 2011, I had to have the shocks and another part relating to running a balanced load replaced. I spent about $500 on those repairs. The parts to replace the shocks took more than 6 weeks to arrive! Roughly one year later, the plastic water pump has broken and needs replacing - another $100 part plus labor. I always believed Maytag was a reputable company, but I am very sad at the quality of the product I purchased based on their reputation. They should be ashamed! To date, the dryer has been good - knock on wood!

My husband and I purchased a Maytag Bravos washer and matching dryer in November of 2009. At three or four months old, the dryer quit drying and was emitting a weird smell and smoky air coming out of it. It was under warranty so a technician was called. A fan blade inside it had broken. The repairman replaced it and the motor as a precaution. There was absolutely nothing inside it that could have broken the fan blade and I always check pockets. My hoses were clear also. He told me that it looked poorly designed inside for air flow. He made a box out of sheet metal to fit inside it that he said would help it with air flow on the inside. I still have the dryer but I dont like it very much because it still doesnt do a great job of drying. It has to run too long and at too high a heat to dry laundry. The latch on the door broke a few months ago and had to be replaced too. I havent had problems with the washer as of yet. I like the washer and it washes very well but I will not buy a Maytag washer or dryer again. WHIRLPOOL OWNS MAYTAG NOW AND THEIR PRODUCTS ARE ACTUALLY MADE BY WHIRLPOOL SO I WOULDNT TURN TO THEM.

Bought a new home in July of 2016 and the builder had included a Maytag Bravos XL washer and dryer. They are THE WORST performing appliances I have ever used! I will replace as soon as I have the means to do so. DO NOT PURCHASE the Maytag Bravos XL appliances. The engineers that designed them should be fired! The washing machine makes an incredibly loud noise (like an old starter grinding in a 50s car). Im told that this is normal for the machine. Does NOT clean well and leaves soap spots on dark clothes... leaves them on light clothes but I cannot see them. Whites come out dingy even with bleach. The tub is so deep that I have to use tongs to get out smaller items, I am 53 tall and have never had this issue before. Soap dispenser drawer wont stay closed during wash cycle. Clothes are so badly tangled during the wash cycle that it is hard to describe the wrinkled mess that has to go into the dryer.Dryer issues: Very loud. Very wobbly and unstable, and yes, it has been leveled 3 times. Bed linens have to be separated at least 3 times during the drying cycles because they twist and wad up into big, wet knots of cloth. Infuriating!!! Dry time is very long unless you wish to cook your clothes. So disappointed in this product. Total rubbish!!

We bought our Maytag Bravos in December 2010. Four months out of warranty, like many other complaints Ive read, we started getting the loud jet taking off noise from the laundry room. Now we are having issues with the lid lock not allowing you to get to the clothes. This machine tries to spin three times and then locks up. It literally locks the lid and will not allow you to get to your clothes! For a machine to fail just four months out of warranty is a joke! After investigating the problems with the machine, it will cost us more to repair than what we originally paid for the washer in the first place. Give me a break! There should be a recall and Maytag should have their feet held to the fire to replace these less than adequate high-dollar machines!

We updated our kitchen appliances in 2013 and purchased all from Home Depot. Purchased Maytag Refrigerator, free standing range and microwave. What a big mistake!!! Not one of them are worth what we paid for them. I just noticed that I was getting a (chemical) smell from inside our 6 year old 3 door model MFI2670XEM5 refrigerator. Well being I know what refrigerant smells like I have a leak in the interior of unit. This is my final issue with Maytag and their so called great built appliances, I have had nothing but troubles since about 2 years after we purchased it.I guess what really surprises me is that unit is built by Whirlpool and has their name all over unit and I always had good luck in the past with the brand. This is one of several issues including rust on freezer door, broken plastic drawer frames to French door hinges broken, ice maker door issues. What a waste of my money that I spent on these and now after 6 years need to buy all new. IT WILL NOT BE Maytag or Whirlpool!!!

Bought a Maytag Dishwasher, model MDB89449SAM1 a little over two years ago and had nothing but trouble with it. Had Repairman out twice before but today he said we would be better off buying a new one! What a piece of JUNK and truly a waste of money! Would not recommend buying any MAYTAG products. They used to be a quality brand but no more.

Model MDB7749AWM2. Paid over $700.00. Figure I would get a good dishwasher so it would last and clean dishes. I was wrong. I replaced all new appliances for kitchen in house we had purchase 3 years ago. I replaced door switch 4 times, front door panel where screws go in broke off. Salesman at Lowe’s said Maytag was a good dishwasher. It is a stainless front and stainless inside. I have had cheaper models and never had problems with.

I positively HATE the new BravosXL Maytag washer, which has no decent agitator. It is ruining my clothes, as it spins with little water and leaves soap residue all over the clothes. Additionally it puts large, long wrinkles in my knits, especially disfiguring slacks. Maytag must have known how rough and ruinous this washer was on knits BEFORE selling it to an unsuspecting public! I want my money back in order to purchase an old-style, well-functioning agitator washing machine.A class-action suit should be brought against Maytag. There was no way to know before buying and using that this machine is horrible!!!

Need to keep cleaning washer otherwise it leaves white marks on clothes. I used vinegar but that didnt help. Used the wash cycle and that didnt help. I found a washer cleaner and it works great. Overall performance of washer is fine but I would be hesitant on purchasing another Maytag Bravo washer only for this reason.

I bought this machine about a year ago. It does not wash your clothes good. Stains nor smell does not come out. It makes this god awful noise that can be heard throughout the house... It suppose to save on your water and electric bill but no savings for me considering I have to wash items 2 or 3 times... I hate this washer and I paid a lot of money for nothing coz that’s what it does - nothing!!!

I purchased a Maytag dishwasher in 2010 model MDB6709AWW1. I only had it a year and the control panel went. They came out and replaced it and the guy told me that they were having a lot of the same problems. Now in 2015 it has gone again. It will run, but you cant change the settings. I took out the extended warranty on it and called 3 weeks ago and they sent out a local appliance repair company. This guy told me he had just come from another house with the same dishwasher with the same problem. He ordered the parts and I have been waiting 2 weeks. I called and the lady told me that they changed the part # and that they dont have any made yet and dont know when they will. WHAT!!! How can a company not have any parts made for their own dishwasher. I didnt buy the dishwasher when I bought all my other appliances, because there was a dishwasher here. It was gross and didnt work well. All my other appliances are Kenmore and I will stick with them. Have owned them for years and never had any problems.

I bought a Maytag Top Loader. I soon discovered that it is not possible to do a cold water wash. After much communication with Maytag Customer Service it was determined that there is no way to bypass it. And it uses a lot of hot water, even on a cold wash. Their explanation was that the water needed to be a certain temperature to make the detergent work effectively. The same detergent that I’ve been using for 40 years with cold water in my Speed Queen. When I need to do a cold water wash, I go to my parents home and use their washer. Disappointing purchase, my last Maytag, for sure.

After researching the top-rated washing machine in consumer reports, we decided to spend the extra cash ($930) and buy the top-rated machine. Spending almost double on a high end machine, you would expect this machine to last longer than three years. The motherboard needs to be replaced because it gets stuck on a UL code near the end of the cycle. Now, we have had two people come try to fix it, and they said to trash it and buy a new one. Only three years! If I had paid $300, I wouldnt be so upset, but that was a total waste of money for it to last less than any machine Ive ever had. How is a consumer supposed to know what a good washing machine is if they spend extra cash for the top-rated machine and that one is still bad? The company should replace something like a motherboard that goes faulty when it had nothing to do with use. So unfair and frustrating.

I also bought a Maytag refrigerator in 2013. Right after the warranty expired it was forming ice on the bottom and back of the freezer and was not making ice. I called Maytag and they told me they have no complaints on this type of refrigerator. It was also always making a lot of noise. Maytag was supposed to be the quiet one. I will never buy another Maytag product and I will do anything to make sure nobody else does either.

I purchased Model #MHW563HW Frond loading automatic washer a little over 1 year. The options are not for me. The quick wash is way too short 20 minutes, all the rest of the options are 51 minutes to 2 hours & 57 minutes! If you wanted to add some extra minutes to the Quick wash you are out of luck. Normal wash is 55 minutes but can last much longer, it takes forever for this machine to balance which adds time to the process.I had an LG front washer before this one and when the clothes came out they were almost dry, not this washer, they are very wet. Then there is the horrible odor that comes after you use it, Ive tried drying every area making sure there isnt a drop in it. Still the stench is unbearable. Yes it has a Clean Washer with Affresh option which takes an additional 128 minutes and you have to do it at least once a week! Thats a LOT of wasted energy. That just doesnt sound efficient to me, washing the washer. Why??? This washer had great reviews which I read, not one mentioning these issues.

On the 11/25/16 bought a refrigerator at Home Depot. Beside that the first was not called off, wait for another month 12/31/16 for the other refrigerator the problem are. I file a complaint because Maytag left me a message refrigerator half a price. Now they deny when I have proof.

This washer is no better than a glorified garbage can. Maytag AKA Whirlpool should be ashamed to put their name on this product. Like others before me on this website my washing machine sounds like a jet is taking off in my basement. When I contacted a serviceman, he told me the drum seal is broken and the bearings are shot. I have the machine since April 11, 2011. Not even three years to date! I do not have an extended warranty so shame on me to believe that a 900.00 machine should last well beyond 3 years. Unfortunately, I am getting the run around from Whirlpool as all of you have experienced. This is criminal. Not only are we as consumers being defrauded by irresponsible manufacturing but these huge hunks of metal and plastic are polluting our environment. Our parents had washing machines and dryers for as long as 20 to 25 years and they actually cleaned clothes. We now have high efficiency machines that destroy our clothing and leave them dirty and wrinkled. They are now made to break in 5 years and from what I see on this website the average for breakdown is becoming 3 years. Do you think that this is not by design? The service call turns out to be more than the value of the machine, so the repairman doesnt even profit as consumers refrain from costly repair and repurchase. The only profitability is gained by the manufacturers that keep pushing out junk to the consumer. These manufacturers should be accountable like the American auto-manufacturers became accountable for the junk they manufactured at the expense of a whole city, Detroit.

Purchased a Maytag range with Aqualift technology in 2013 thinking it was a good brand and *happy* to find a new way to self-clean my oven. This turns out to be nothing but a joke and I am not *happy* with it. After following directions to the letter, there is some loosening of anything on the floor of the oven, but the sides and top are slowly being coated with more and more grease. Ive spent way too much time with my head in the oven trying to scrub stuff without using a heavy duty cleaner but feel I now need to resort to Easy Off as there is no other way to get it clean. I also dont understand why they tell you to remove the racks since there obviously isnt enough going on to even clean the oven... How would the racks be damaged? And now I believe there is a problem with the Dual Choice element where Im not able to turn the temperature down. Even turned back to the low setting, the pan cooks away like its on high. I have to keep turning it off and then back on in an attempt to find something similar to medium or low heat. Im so very disappointed in Maytag and feel this method of oven cleaning should never have been put on the market. Its a scam!

I have called numerous times and the satisfaction is out the window. The MOLD is so bad on the gasket that I can not get it off and it just keeps getting worse. My clothes smell musty even after they are washed. Really fed up... I have had different Maytags for at least 40 years and I will not purchase another one at this point. Apparently your customer service is as bad as some of your machines. My word of mouth is not good advertising for you.

Just bought a Maytag Bravos 4.3 cu ft washing machine from NFM. The first machine delivered was broken it didnt wash or spin the clothes. NFM sent out another one at 9:30pm. It doesnt spin the clothes out well & loads have to be small. Poorly made.

I purchased a Maytag Centennial MVWC360AW washing machine on July 11, 2013 at The Home Depot. I assumed that I was getting a good product based on my Moms old Maytag washer. This machine is the farthest thing from quality that I have ever experienced. My Mom would roll over in her grave if she knew how CHEAP Whirlpool has built---what is supposed to be a---Maytag! The machine worked fairly well, at first. Even though I didnt like the low water arrangement. I like clothes to be fully immersed in water! That went on for 2 years and 5 months, until NOW the led light goes to Rinse, but it wont agitate. Then the led light goes toSpin, but it wont spin! I called a local appliance repairman and he told me that the control is bad. They cost about $250.00. Its not worth repairing!! So, Im stuck with this piece of junk! Shame on Maytag/Whirlpool for building a PIECE OF JUNK!

I bought my Maytag in 2013. It worked fine at first but for the last year it isnt getting clothes clean. In fact, some look like theyve never been washed. I have to run the rinse cycle 2-3 times and they still seem somewhat soapy. The washer still leaves clothes drippy after running the spin cycle. It takes 2-3 hours to complete a small load. I wish I had my old Kenmore back. It worked fine for nearly 20 years!

I have gone several years with wasted food at random times because my Maytag refrigerator decides to stop cooling whenever it feels like it. This is a continuing thing that started since the appliance was brand new and it has never been resolved. Maytag claims that they cant do anything about my refrigerator. They can do what they want to. From my experience, I feel like the issue is that they dont care to make it right. I am finally fed up with this refrigerator and I am buying a new one. I can guarantee that it will not be a Maytag.

We bought a Maytag Dishwasher on March 16, 2013. Less than 10 months, we had repairman come in 5 times. First was soap scums left on the glasses after a wash. Then, the soap dispenser was leaking. Now the control panel is not working. We have to wait for a week for the parts to come in. Total length of time for hand washing dishes since we bought this dish washer is three weeks. They said they are not going to replace it until it cant not be repaired. What does that mean?? Please never ever buy Maytag dishwashers!!!!!

Bought new washer and dryer from Home Depot. The worst washer and dryer I ever bought. Own 11 house all have washer and dryers. Bought Maytag on brand reputation. Washer does not rinse close at all. They come out full of lint and soap. It rips sheets up. Takes like 70-90 minutes to wash and close have to be washed over cause they dont rinse out. Dryer takes (2) runs to dry. Depot said they couldnt take them back. $300 Roper washer and dryer work much better than these units I paid like $1100.00 for. Maytag reputation is **. I have Amana front loads in another house that wash in 29 minutes and they come out perfect. Amana dryer works great also. DONT BUY MAYTAG ON THEIR ** REPUTATION AND CONSUMER SERVICE WONT DO ANYTHING!!! I would add the receipt but it just a waste of time.

Faulty control board. Have owned a Maytag dishwasher model MDB6769PASI for 2.5 years. The unit started beeping at random times for about a week - then went dead! Sounds like other reported failures and it is unlikely repairs will be permanent! Never again Maytag.

We purchased a Bravo HE washer about a year ago after our old Maytag finally died after 17 years. Our new one is more quiet, does a good job with less water although the cycle times are a bit longer.

I bought a Maytag dishwasher in 2019 in Home Depot for my new home. The dishwasher stopped washing dishes after two years and 6 months. The price of the new machine was 700$ and I did not buy the extended warranty. The trouble is circulation pump, that cost to install the new one from local service would be about 350$ plus the new pump 150$. I consider quality is very poor if the new dishwasher works only two years and then it is better to buy a new item than fix the old one. Never never buy Maytag production.

I purchased an appliance package of washer dryer, refrigerator and dishwasher. All of the appliances needed many repairs. It took four icemakers in the fridge before it actually was fixed. The worst appliance was the dishwasher it was repaired every three months for six years! Washer and dryer died after five years.

I purchased a Maytag Neptune Washer in 2006 for $665.00 from Sears. Three years later, the control board broke and I paid $400 to replace it. In 2011, the motor and motor board need replacing which will cost $410.00. We kept getting an LR code. So in 5 years, our repairs cost more than the original machine. Maytag can count on never getting my business again. Im only sorry that I purchased a Maytag dishwasher this Summer.

350.00 dollars for repair on a 3 1/2 year old washing machine. Machine wont finish spinning and lid lock keeps flashing on and off and sometimes stays off. Never finishes spinning. A lot of complaints on this! This should be recalled! Always was a Maytag customer but no more!

Within the first year of having this washer (Maytag Bravos X series) the cam broke in it. And then about two months after the warranty went out, the motor quit. It wouldnt spin my clothes at all and would never get my clothes clean. I was having to hand wash my clothes just to get them clean. Not a very happy person, I live paycheck to paycheck and cant afford rock continuously pay to have my washer fixed.

I always thought Maytag was the best, maybe because of their ad. Finally, I bought a refrigerator two months ago, which has turned into a nightmare. The company has sent a tech six times and they all say that it is a bad design which makes my vegetable drawer full of water because of moisture. And they refused to do anything about it every time (bad management). They have already spent more money on service than what I paid for the refrigerator. Figure that out.Do not buy Maytag. It was the biggest mistake I made. I also bought a washer and a dryer at the same time. I wish I could send them all back because of the ignorant people they have working for them in their complaint and service office. Anybody out there, if you want to buy an appliance, make sure it is not Maytag.

Purchased my microwave in 2005 and seldom used it. However in the last few months, the halogen light which lights up the range surface has been flickering. When I asked an electrician doing other work around my house to repair it, he discovered that the halogen light is attached with a dual pin socket which is plastic. When the halogen light gets overheated (and halogen produces alight of heat) it melts the plastic. It has already melted some of the plastic socket. When it fails to operate, I will have to repair the light socket which will be very expensive or buy a new microwave. This microwave cost $800 or more because it offered convection cooking which I have seldom used.This is what is presumed quality appliance? Plus I added the cost of an extended warranty.

We inherited this Maytag (Model MGR7662WW) when we bought our house this year. I love this unit. It cooks accurately, its easy to clean and its just rock solid in its performance. I never worry that the cook times are going to be off either. The oven racks are solid and the overall look is nice. Our friends and family love the center grill as much as we do. If I need to pull something off the burner I dont worry that Ill scratch the stove top with this feature. The oven heat is also pretty contained. Our old oven radiated lots of heat through the top. This one doesnt and thats a huge plus. The only reason Im not giving it 5 stars is that the grills are cracking (not the center one). However, I have no way of knowing if the original buyer damaged them or if its a defect in materials. They still work fine but I will need to replace them at some point. Given the cost of replacing them Ill wait as long as I can.

Have had continual problems with Maytag Bravos. They will replace in under a 5 year warranty. If not for the warranty, I would be out over 700 dollars spent on this very bad machine. Based on my experience Maytag washers are of poor quality. I would stay away.

Our Maytag Bravos is 4 years old. Settings are preset at the factory. Besides the glitches others have written, the hot water sensor INSIDE the machine has gone out. This means - no clothes can be washed on the hot setting, and the warm setting gives only lukewarm water. I have had more than one plumber look at the machine, and the consensus is...the internal sensor needs replacement. However, this machine being only 48 months old, I am debating whether or not just to buy a new machine. This is a HE washer, and I am very disappointed in its performance. This is the worst Maytag machine I have ever owned.

Great dishwasher. The dishwasher heat cycle doesnt dry the dishes but I havent read the instructions yet. This is a large dishwasher holding lots of dishes. Dishes are clean after the cycle. Washes lots of dishes at the same time. Has handy utensil pull out to put away your utensils after dry.

I purchased this dryer in September 2011. By August 2012, one month before the warranty expires, the thermo fuse blew and the dryer would not dry; no heat. I replaced fuse and 30 days later, it blew again. I replaced it again and now, March 2013, 6 months later, the same thing; the thermo fuse blew, no heat. The vent is clean and air flow is very good. Maytag will not admit a problem. This is not an inexpensive dryer; it may be cheap, but not inexpensive. Maytag quality appears to have vanished. I have Maytag throughout the house but will think twice before purchasing Maytag again. Chinese produced parts/products are inferior. Maybe Ill look at Bosch or LG from now on.

We purchased our Maytag Bravos washer/dryer in January of 2012. In October of 2013, I noticed that the lid would not close properly. In examining the lid, we discovered that the screws were in tact but the information panel on the inside of the lid had come unglued causing the lid to be obstructed from closing properly. After calling Maytag we were told that they make a quality product and, in what I consider to be a condescending reply, could not help us. Replacement of the lid with the service call would cost almost the cost of this expensive washer. So disappointed in what we thought was a wise purchase!

I bought the dishwasher (Model MDB7749AWM) 15 months ago and paid $490.00. I had to put a new console in it ($245.00) on 07/16/2012. So that’s $735.00. Two days ago, the console went out again! I’m not putting $245 more in it! I called Maytag’s office. They more or less told me that was my problem! I am throwing that piece of junk away! And I’m buying a different brand. Maytag does not stand behind their product. Last Maytag I will buy! Warning! Do not buy Maytag!

I purchased a new Maytag dishwasher model MDB7609AWB1 approximately 2yrs ago from Sears. We purchased quite a few new appliances from them and they are always helpful. Within the first year, right after the warranty was up, it stopped working. No lights on the power panel. I called Sears, out of warranty, sorry. Said they would give me a deal on the repair. Sears came out, replaced the computer. $230.00. 6 months later, it stops working again. I go on line to look up these models and sure enough a lot of people are having the same issues. I did some of the checks that they said to do and found my plastic door latch was broken. A little plastic arm that actuates the switches broke. Should have been made of metal. I replace it myself, very easy, by the way. So I figure, in another 8 months it will prob break again. They run anywhere from $19.00-$30.00. 2 days ago power panel and light, not working again. I called Sears and asked them if they were having issues with the power panels that this was the second time in less than 2 years, and if there were any recalls, they said no. I guess they dont follow their reviews, but according to google reviews, its a major problem with most of them. Maytag, Whirlpool, and Amanda. Ordered a new panel today, again they are $141 from Sears but if you shop, you can get a new one for less than $85.00. If you have any kind of mechanical skills, you can replace it in less than 20 mins. It just seems to me that this big companies have let their quality control go and are more concerned about the profit. There should be a recall on these. Do Not buy a Maytag/Whirlpool dishwasher, they are total junk. Sorry Maytag, you lost another customer.

I have always hated soft touch control panels so I purchased a Maytag Dishwasher with old style push buttons. IT DID NOT CLEAN THE DISHES, so Lowes took it back and I was convinced to UPGRADE to an MDB7749SBB0 and was told this machine was top of the line, although it was VERY temperamental from the start. I guess I should have done my homework. I see now several complaints about the control panels not working. I was told that MAYTAG was a very reputable company and that they stand behind their product. WRONG!. The company KNOWS these panels have problems and should replace them free of charge as it is obviously a defect. Nope, first they offer to send someone out (In a week) to repair it at $80 just to look at it and the panel is over $100 to replace, and when I complained they tried to sell me extra coverage for $250. REALLY? What is the purpose of purchasing a QUALITY dishwasher? I might as well purchase a cheap dishwasher and replace it when it breaks. I think you should be responsible for your product when you have several complaints on a specific part.

Bravos XL Top loading High Efficiency Low Water Washer and Dryer - I gave this washing machine a 1 star but would give it a 0 star or less if the choice was available. I agree with everything others have voiced about this washer. I end up using the bulky cycle for everything because it is the only cycle I have found that will use enough water to get the clothes moving around. All the other cycles are a joke. First you must put everything around the wall of the tub away from the so called agitator. Then about 2 cups of water enters the machine. It then goes into this high speed spin. In my opinion it just pushes any soil deeper into the fibers. The drum will then spin slowly and water will spray on the clothes for several minutes but the washer never fills with enough water to cover the clothes. Watching it agitate through the glass top is almost hysterical. Laundry is barely moving. The high speed spin they push as a selling point puts deep wrinkles in everything and the wrinkle control setting on the dryer does nothing for them. It is absolutely the worst machine I have ever owned. My husband has repeatedly told me to sell these and buy another set. I will be ashamed to sell it to anyone. Im not sure how the makers of Maytag got away with selling these machines. I know there are different models but from what I have read they all work the same. I replaced a very low end GE Washer and Dryer with this pair and every time I do laundry I wish I had them back. The matching dryer is very costly to run as almost every load takes 2 cycles to get items dry. Nothing comes out completely dry even if you put it on the more dry setting.

Purchased in 2013, they have replaced the control panel twice in 2014 and AGAIN 2015, now WAITING for the replacement control panel AGAIN. Maytag claims there are no recalls on this dishwasher model number. But after reading all these reviews why is there not a recall. Maytag is of no help when you call. They claim as long as they keep replacing the control panel it still can be repaired. This can be extremely costly WHEN THE CONTROL CONSOLE PANEL keeps breaking. Obviously there is a major problem with this part and why is Maytag not recognizing this issue.

The Bravos XL MCT Maytag commercial Technology is not a good machine. I noticed it within the first few weeks. I called Conns to request technical support but the technician they sent didnt solve the problem. I also called Maytag, they also sent a technician. He told me the same thing as the other guy. To use good quality detergent and to make sure the clothes are neatly arrange around the drums walls. Nothing works. My clothes dont get clean because they dont get wet. Theres lots of residuals and wrinkles all over them. Also, the machine takes way too long to finish a load of clothes. I did tried to return it, but Conns wouldnt take it back. I dont recommend this washing machine at all!

Oven was purchased and put in May 2014. I have not be able to use. The oven temperature is off. If the oven is used at 500 degrees the temperature is really 900. I thought I had a gas leak because I got a bad headache because of the smell. The gas co told me to get a repair person to look at it. Maytag has been horrible to deal with. I have taken 3 separate days off trying to get it fixed. The last Maytag repair man had the nerve to ask me where the gas line was. He shut the wrong off and had a gas leak in my house. I had to open all windows. He was supposed to come back the next day. He did not and I received no calls. I have paid for an oven that is dangerous that I cannot use. I feel Im being treated this way because I am an older woman. I will never buy another Maytag.

I really liked my Maytag Bravo X washer. Until, at less than 2 years old, it started having issues. It all of a sudden starting sticking in the spin mode, then it wouldnt turn off even though the cycle was complete. I have to pull the plug out of the machine it to stop from continuously running. I was charged $104 to have a certified tech come out for 15 minutes and recalibrate it and it worked for another month. It started having that same problem again and now, I have learned I need a new control board, which costs over $200, plus labor, over $60. The Maytag service rep I spoke with was very pleasant when she told me she spoke with her supervisor and told me there was nothing they can. So now I dont like my pretty new machine at all, and have to decide if I should stick almost $300 into getting it fixed again, or buy a new washer, NOT A MAYTAG! As I voiced my complaint on the Maytag website I saw that there were many of the same complaints about the faulty control board and am wondering what does it take to get a recall?

I bought a Maytag dishwasher in January 2013. Three months later, the cheap plastic latch on the door malfunctioned. I waited 3 weeks for the repairmen to get the part in. Is there a sense of urgency anymore? If I owed Maytag money, I bet there would be a real sense of urgency on their part. Next time it will be an LG dishwasher.

We purchased this Maytag Centennial washer in 2009 (model # mvwc6esw/Wd; type 849-05; ser # cy1741855) and I have hated it ever since. I had an old 406 Maytag washer that was worth its weight in gold - repaired it as long as possible. I bought this new one because it was a Maytag and that was a mistake. The way it agitates my clothes get tangled and they never did that in the other original Maytag. We had to have it fixed not long after we got it and now every time I turn it on, it immediately starts to agitate on every cycle except hand wash, which it never did before. If I knew it agitated the way it did, I never would have got it. Good thing we bought an extended warranty for this machine. We have used it once already and it looks like we may have to use it again. I am very disappointed in this machine and your workmanship. The old machines were much better and more dependable.

A lot of the reviews contain complaints about the Bravos XL MCT top load washer. We purchased one in December, 2015, and so far have not had any problems. We had a 3 yr old Whirlpool side loading washer that we just gave away, as it never got enough water to even dampen a comforter or quilt. This machine works very well, in spite of lower level of water. I was pleasantly surprised when I could see the water level with the first load! The controls are not as intuitive as other machines; e.g. spin only requires you to select Rinse/Spin cycle, and THEN turn OFF extra rinse. Perhaps the proper way is to have a Spin-Only cycle, and then tell the user to click the extra rinse ON. We do probably 1 load a day. Water bill has not been significantly higher than when we had the Whirlpool that hardly used any water. Today, though, a heavy quilt (it WAS distributed evenly around the impeller) was put on Bedding so the water level would be a bit higher to ensure the entire quilt was wet. Fine so far. However, during the Spin Cycle, the unbalance became so violent that the washer stopped for a few seconds and then went BACK to the Rinse cycle. It did this several times before we realized that the time remaining had not gone down in over 30 minutes. My guess was that the sensor believed that maybe some additional water with another Rinse cycle MIGHT even out the load. It didnt. I finally stopped the machine, redistributed the quilt and then ran the Rinse/Spin cycle, choosing NOT to do the extra rinse. All came out fine. There was NOTHING in the manual indicating that this might be needed, except for the instructions to Spin only. If I have any other problems, I will send here.

The washer is making loud noises. I had a repairman out and he said the transmission was shot. This washer is only 7.5 years old and the set I had before lasted 19 years. It also was a Maytag. My mother, sisters and aunts have always stood by Maytags and I am disappointed that this washer being 7.5 years old is shot. The dryer to the set is working great!

I bought a Maytag dishwasher Model MDB7749SBW3 from Home Depot 6/2014 and by December 2015, the touch panel was going crazy! Ive read a lot of reviews and this seems to be common for Maytags. It would cost me almost as much to have this machine repaired, with a service call and the cost of a new panel, as it did when I bought it. When talking to an appliance repairman, he informed me that Maytag and most all the major brands are now owned by Whirlpool and that they are basically junk--not meant to last more then 1-3 years! Where are the recalls and how do we get a recall started?

Maytag MVW823OHC SLATE washing machine, $1050 plus warranty $169.95 on 05/27/21 not delivered until 06/25/21, error code on 09/19/21. It is 11/03/21, machine is not working and no part available. Sad.

I purchased my Bravos washer and dryer in about July of 2012. So far I have no complaints about the dryer but I hate the washing machine as do two friends of mine. My husband specifically wanted something energy efficient which is why we didnt purchase the basic traditional style washer weve always used. From the first time I used the washer, I was amazed and disappointed at the noise level. Because the lid is glass, I could observe the water level during each part of the laundry cycle. The water did not cover the laundry in the washer.When I mentioned this to one of my friends, she said that she has to wash some of her clothes twice. How is this energy efficient? I finally figured out that using the heavy duty wash cycle and heavy soil setting usually results in more water but requires an hour to wash and rinse the clothes. The downside is that the heavy duty cycle is too hard on some of my more delicate items so I have to hand wash many more clothes than I did with my old style washer that allowed me to select the water level I wanted. Most recently, when I washed a bulky mattress pad with a few other items, the water level never covered the pad because the load of laundry was so lightweight. At the end of the cycle, parts of the mattress pad were bone dry so I will have to take it to the laundromat if I cannot make the washing machine fill up with water high enough to cover the mattress pad. I dont want to spend the amount of time hand washing so much of my clothing, monitoring the water level in the washing machine and rewashing loads of laundry. After reading many of these comments, it appears that I have many more issues to look forward to. When this washer starts to break down, I will go back to an old style machine and a different brand.

I have Maytag Model MGT8885XS03 Gas Range. I bought it in Nov 2013. The surface burner valves, which regulate the gas flow, are a bad design. One valve got stuck and needed replacement within first 13 month. Then another valve got stuck about a year ago and the third one got stuck today Nov 19. So far I spent $400.00, just for 2 of them and the last one has not being replaced yet. This is a safety issue, because it always happen when the stove is on and will not turn off. I need Maytag to replace my stove because I am afraid this will burn my house down. I bought Maytag because they always advertise as quality product, and now I have to live with the nightmare of burning my house down.

I bought the Maytag Bravos XL HE washing machine because I needed a machine that could handle large loads to save me time doing multiple loads for everyday items like jeans to towels, blankets as well as delicates. This machine is a COMPLETE disappointment. It does NOT get anything clean unless I wash it 4 times with bleach and pre-stain 4 times. You know what bleach does to your clothes! The water level is so low I can only wash 4 things at a time and I still have to wash additional times. It doesnt get the smell or food stains out. Not a good choice for an active family or person. Ive had clothes come out with suds still on them after washing three times. I use less than the recommended amount of HE detergent. There was a $250 agitator washer by GE at Lowes but it was smaller - how I wish I bought it. These impeller HE machines dont work. My advice steer clear of this Maytag product unless you like to waste your time re-doing loads of laundry.

I purchased both the washer and dryer in this series. First the washer does a horrible job actually cleaning the clothes unless you set it as a bulky load and use more water. Despite that issue, after only owning the set for four years the dryer broke down. It made a terrible noise and you could not run it because it was far too noisy. My husband thankfully bought a replacement part and fixed that issue. A few months later I started having trouble with the washing machine. It freezes constantly and I have to unplug to get it working again. It usually take over 15 times to actually get it to begin to fill with water. Now it started to stop working during the wash cycle and I have to unplug it again to get it going. Most times I have to change it to another setting like rinse and spin or drain and spin to complete a wash cycle. Last night it began to have a plastic burning smell. I used to own the same washer for 20 years and only had minor issues that come with extended use. To only own this pair for under five years and have them both break down proves that these are poorly made products and you should save your money and purchase a different brand altogether. I will never buy another Maytag as long as I live if this is how well their products are made. I expect to have my appliances last longer than five years for their price. So save your money when it comes to these machines. I promise you will not be happy with your purchase. I will either have to repair the washer and hope it will last at least a few more years or chalk this up to a lesson learned and discard both machines.

We bought this Maytag washer 3 mo. ago and now need work done on it. We were told that they could not find anyone willing to come work in this area. We live in the Mississippi Delta, 30 miles so. of Greenville, 50 miles no. of Vicksburg or 90 miles from Jackson. So I guess the Maytag repairman is not just lonely anymore, he doesnt exist.

I recently purchased a new Maytag Commercial top loading Bravos from Lowes. It looked like a sturdy model and has a 10-year parts warranty and to cover this washer even more... I purchased the additional warranty from the factory. The washer is delivered, set up... First batch of laundry the washer is making all kinds of noise, the clothes are wet..water didnt dissolve soap packet... Repairman comes out..washer out of balance, cold water not at full pressure... Computer failure noted. Now still making a lot of noise, my clothes are twisted and intertwined and still dirty. My dryer isnt even taking the wrinkles out and even after I iron on hi steam the clothes are still wrinkled beyond belief... Im so dissatisfied with the washer... I want to return it... I cant believe Maytag would manufacture a washer that is ruining my clothes...

We purchased a Maytag Dishwasher in 2011. In 2014 I got no response from the control panel when trying to start the machine. Service came out and had to replace the control panel. The cost for that repair was $269.00. It has now just stopped working again. Same issue. After seeing all the posts, I realize that this is a prevalent issue and in some cases a safety concern. If Maytag knows about this issue with their control panels why have they not recalled or corrected these problems! Needless to say, I will never trust this company again!!! Model number MDB7749AWM2.

Maytag Bravo was making loud noise in the Spin cycle. Ordered new bearing, shaft and parts from Amazon. Also had to order the Bearing tool, cost more than the bearing parts. Total cost $145. Watch a youtube video on replacement, took about 3.5 hrs by myself. Biggest problem I had was lifting the washer up over the drain pan it is in. Washer is on the 2nd floor.

Tried various cycles and I hear water going in but don’t see any water. How does this wash clothes. I want to see water and soap clean the clothes. If I want dry cleaning I will bring the clothes to the dry cleaner. Never again will I buy a high efficiency washer. My clothes do not come out clean!

Maytag French door model is four years old. Water accumulates on the freezer floor in small puddles. As I read other comments, this seems quite often the case. I should probably pull out the refrigerator to see if I have water leakage on my floor. From reading other reviews, it appears that Maytag does not stand behind the product. Am I forced to do the repairs myself, or am I forced to find a repair person and hope their fix eliminates the problem? Any advice would be helpful.

Maytag dishwasher model MDBH979SAM1 purchased December 2012 From Home Depot. After only 14 months of usage the front panel ceased to work. Contacted maytag about issue and they responded THERE ARE NO KNOWN ISSUES WITH THIS MODEL. After doing some research (5 seconds), I have found thousands of people with the exact same issue. Maytag has stuck their head in the sand. Either they are ignoring this issue or just dont care due to excessive cost of replacement. This is obviously a design flaw due to poor engineering and Maytag needs to stand behind their product and fix this issue. Personally we had to save up for 1 1/2 years in order to afford a dishwasher. Now we are stuck. Some people have replaced this part costing $200 2-3 times. I cannot afford to take the chance on a repair. I will have to start saving again for a new dishwasher and this one will not be a Maytag. (Less)

Maytag Performa Side by Side fridge PSD262LHEB door handle pulled off for the second time since purchase but this time, the handle knocked over a pot of hot water on me. I am just relieved that I have no small children anymore. I would consider this very dangerous in any household. The first time, it was covered under warranty along with the broken ice maker. The repairman stated that he had replaced many handles and due to design flaw, they would not last long.

I bought it from a local dealer so that I could get it serviced locally. I bought it in 2012 and paid $750 for it. I hate just about everything about this (and all modern) washing machines. The deal breaker is all these safety features that are really inconvenient and pointless. If I could have found a good used washing machine at least 10 years old, I would have bought it. This is a Maytag Centennial. I dont like the automatically locking door, the inability to choose the water level myself, and the requirement to use a particular kind of soap. Also, I hate the idea that I have to clean the washing machine from time to time. Whoever heard of that? But you have to do it otherwise your clothes will have a sour smell. These new washing machines are not an advance in technology. I may have to go back to using a wringer machine.

We bought 10 18-lb washers about a year ago. They are a maintenance nightmare. For example on June 5 7 out of 10 machine were out of service. One has been down since Jan 20 and the others for various lengths of time. The guarantee for these machines has been misleading since the parts for repair are never available. We are losing business and money because of the Maytag failure to provide equipment that operates as advertised. We need help now.

Purchased Maytag dishwasher model MDB7609AWW2 3 yrs ago. Started having problems with it not filling with water after first cycle. After examination determined that the control panel/handle on the top of the door had broken away from its attachment points/screws behind the pane. Every time the door was opened this would allow moisture and steam to infiltrate into the door interior. And guess what, it now needs a new electronic control panel. After seeing all the other reviews, it is safe to say this is not the Maytag of our parents or grandparents.

I purchased the Maytag oven in January and have had the service technician out 5 times to try to repair the oven because it doesnt heat properly. Theyve told me that because I live in a condominium that it is normal for the oven to take an hour to preheat, then another hour for the second oven to preheat. When I am baking the oven does not hold the temperature and anything I bake takes much longer than it should. They refuse to get me a new oven.

I will NEVER get another Maytag product ever again! My not even 1 year old washer broke and I have been waiting almost 2 1/2 months for a part to be replaced. My partner and I are nurses working on the front lines during this COVID pandemic and I can’t even wash my scrubs at my own house but instead I have to go to a damn washateria. The “supervisor” told me 2 weeks ago that if the part is not in by today, 1/27/21, that a brand new washer will be sent to me. Well I call today and the people I spoke to denied any recollection of this information. The “supervisor” stated that she is “documenting all of the information” so when I called back I would not have a problem. Once again I have been lied to and wasting my breath and time. The customer service has been TERRIBLE and I cannot believe that this was once a “reliable” brand! Clearly this brand is unreliable and the personnel is also unreliable. NEVER AGAIN WILL I BUY A MAYTAG! Save your money and buy a different brand!

Dinner ruined again... I bought all brand new Maytag stove MERS755RAW, I can only use one area and that has cant move them, the racks fall through. I have burned myself time after time when attempting to pull the racks in or out. Friends arrived and when we pulled cooked dinner out the rack fell through and it was so hot I could not hold it causing the entire dinner to come crashing down and spilling everywhere. I along with my family cannot use it again. Can anyone assist or make a recommendation? New racks do not work as it appears that oven has expanded and the dimension have changed. Do they have a recall or safety repair bulletin?

It looks big, but is small inside. Its hard to put in several large items. The water filter broke and too expensive to fix. I like the double doors and ice maker. I dont like the freezer drawer. It wont stay open to clean.

We purchased a Maytag Bravo in 2011. With only three adults in the house using it for regular clothes washing, we were surprised when we had to call a repairman and the charge was going to be over $500 to fix the transmission and clutch. We had the same problem as described in many of the other comments, i.e., door sensor would not work properly and machine would not spin. Not even worth it to fix. Word is that Maytag is made by Whirlpool and if this is true, it would explain the disappointment. We have replaced more Whirlpool appliances than I can count. Never again Maytag!

Maytag Bravos quiet series 300 - We have had this washing machine for approx. 2 years and there is rust marking around the opening of the spout where the bleach is poured into. We also find that we have to do the clean cycle quite often. And it bounces and make a loud noise if there is not enough clothing in it… even on the bulky cycle. I WOULD NOT RECOMMEND THIS PRODUCT TO ANYONE! And we have been loyal purchasers for 40 plus years!

I asked a simple question online to see the location of the lint trap on my washer, I had read my manual and could find nothing about the lint trap, and to get a simple answer as to location, they wanted to be paid $30.00, I dont want them to come and show me just a simple answer as to where I could find it. It should be in the owners manual but it isnt

My Maytag 2000 has ripped our clothes. This is my 1st front loading set. I looked on the internet and it seems that this is a known problem. Very upset that a brand that I had for 30 years and recommended to others as well has turned into a terrible company. Im a single mom and Im not in a position to replace a washer every year. I trusted Maytag! A recall and either replacement of the parts, or delivery of new part to fix the problem should have been put in place. I wrote to Maytag to see if they will do something to fix this problem.I have the set, washer shakes a lot, but works well. Washer also always has a lot of water left on the door seals folds, terrible design... I will post on other sites to warn other customers. This is not OK, my clothes are destroyed. See pictures. Clothes got trapped in a gap that exists in the perimeter of the opening, where it meets the door. Why is there a gap at all???

It is actually an older model Maytag set that I bought used 4.5 yrs ago. I am very impressed how its held up and how fresh our clothes are still. I have always loved Maytag and will buy again if needed.

I have a Maytag fridge/freezer model number MFF2557 10403089ER. The freezer keeps going out. The repairman replaced the computer board called a jazz board stating that the bulbs in the fridge part are too close to the board and the heat can cause the board to short out. He suggested switching bulbs to 25 watts which cannot be found for fridges. The freezer continues to go out and sometimes restarts itself or by flipping the breaker switch, brings it back. In the meantime, food is ruined. Yesterday, he put a new starter relay on the compressor stating that this series of fridge/ freezer has had a problem with the compressor and Maytag will not take responsibility for this. There is no recall at this time and we are waiting to see if this corrects the problem or if the freezer will continue to go out. Thank you for your help in this matter.

I had a GE washer and dryer when I first moved to my new home - lasted 15 years. Then... bought a set of Maytag and they have both been the biggest pain in the world. Spent 3000 and Im ready to toss them after 3 years. Dont buy Maytag!!!

On Nov 1, 2018 - 14 months after purchasing this top of the line refrigerator - the compressor broke and the freezer stopped functioning. I called Maytag Service who said the soonest they could repair it was Nov 12 - 12 days after it broke. Also they said my 10 year warranty didnt apply unless I had proof of purchase. I said I registered my product online when I bought it but they said they had no record. So they had to charge me full cost of service and parts which would be $1000-$1500.I then called LOWES SERVICE ADVANTAGE - I really like Lowes by the way - and they verified my proof of purchase and that in addition to the appliance warranty I have a 5 YEAR mechanical parts repair warranty through LOWES. Thank goodness I purchased the service warranty from LOWES because Maytag was NOT honoring theirs! So then a repair person from FAST APPLIANCE REPAIR INC came to fix the refrigerator and said because it was the compressor he couldnt repair it so I had to wait a few days later for the COMPRESSOR SPECIALIST to come out. The compressor specialist came and said he didnt have any in stock so had to order one.Six days later - Nov 19 - the compressor arrived at my house. I called FAST APPLIANCE REPAIR and asked for someone to schedule an installation. I said Im RETIRED and can do it any time. They said the soonest they could install it is NOVEMBER 28 - ONE MONTH AFTER IT BROKE. So now Ive lost two large drawers of frozen food that spoiled. I have no refrigerator this week for my birthday and for Thanksgiving. I have to wait another 9 days to get it fixed. I am NOT HAPPY. I am sharing this experience so anyone considering buying this or any other MAYTAG product will think very carefully before making their purchase. Also, be sure to buy from Lowes and get the Lowes service plan for any appliance. Ill try to update this if and when my refrigerator gets repaired.

First I would like to thank the salesman who has worked diligently to solve the problem I am having. The first load of dark clothes I washed came out with what looked like lint on them. It has to be scraped off. Yes I am using HE detergent. Yes I am using the minimum amount recommended by the manufacturer. & yes to all the other questions I have asked. The solution was to wash the dark clothes on power wash with an extra rinse. Very energy efficient! This was NOT the answer so I was given a 1-800 # to call. After giving all the necessary information & answering all of the questions about detergent etc. the conversation became a little more in depth. Does it happen with dark clothes? Do you dry your clothes outside or in a drier? It was becoming obvious to me that Maytag is aware of this problem. By this point I was even unhappier as no solutions were being offered. Finally after several would you mind holding the line again for just a minute he said he couldnt tell me to do this but some of his friends add a cup of vinegar to their wash. At this point I told him I was sorry I had ever bought this machine. He then said he would have a technician arrange an appointment. He arrived & declared I was using too much detergent even though by then I was using half on the manufacturers recommended amount. Buying an energy efficient washer where I have to use POWER WASH, EXTRA RINSE, VINEGAR & DRIER is not a good answer for a problem Maytag must be aware of as I read the reviews today. I have just done 2 loads of dark laundry with no detergent & the pants are marked so I WANT AN ANSWER.

I purchased a Maytag Bravos 500 Series HE washer. 3/2013. The machine sensor started giving problems less than 2 years after purchase. The sensor is not working. The wash lights stays on, and the clothes are not cleaned. I have to manually turn the dial to put in on the rinse cycle and then turn the dial to the spin cycle. Its a piece of junk. I called Maytag twice and the only thing the representatives on the phone say: I will send a certified technician to see whats the problem. Price: $129.00 service call and additional costs for labor, parts, etc. Maytag had a very good reputation for its products. Will never buy anything Maytag or any products that fall under that brand.

Purchased washer March 2017 and had to get it repaired twice by the end of 2018. The top loader even with agitator does not clean clothes very well. The repairman said not to fill the washer above halfway so I can only wash about 4 pair of my husbands heavy soiled work jeans. I won’t buy another Maytag.

I bought Washer and Dryer Pair new less than 2 years ago. Within 6 months of purchase, the bearing went - warranty. Then 1 week before one year old, bearing went again. I contacted Maytag. They told me it was my problem and I should have bought extended warranty. Lemon law should apply and I asked about appeal process and was told that there is no such thing. Now, the washer is needing a new pump and it is not even 2 years old!

I purchased a new Maytag top loader at Home Depot. They delivered and set up. From the first load, I have had problems with the washer stopping and jerking. Clothing becomes a tangled mess. I contacted Maytag, they suggested I make sure I put on proper setting for the items within the washer. I do not know how one can fail at putting sheets in the washer and putting the setting on sheets and they are so twisted you have to spend time pulling them apart. This happens to almost everything I wash. I believe that I have a lemon, still under warranty, Maytag believes I should pay for a house call. Home Depot will only forward the information to me that Maytag gives to them.

I bought a Maytag MGR5605WW range on July 3, 2011 and it took till mid August before I received it. Right away I noticed when I put a pan on the grates, I had to be careful so they did not slip off. Dangerous! Then I made a pizza, and when I pulled the rack out of the oven, the rack tipped down and the pizza slid down on the oven. Danger again! I went over to Menards and they gave me the number of A&E (1-800-771-3029). I called them when I got home and an A&E person said they would call me back. After a few more calls, no one ever called me back. I went back to Menards. They said I need to deal with Maytag. I am very concerned with the racks, and so is everyone else. They are cheaply made. Tonight I had a family member place the frozen turkey on the rack and it bowed down! Danger again. The grates have a few chips. This is a nightmare. What a piece of trash. I’m trying to get someone to respond. This stove is dangerous to my well-being, and I have no other choice but to use it.

I purchased a Maytag dishwasher for $500. After several months of it working less days than not working, I contacted the repairman. I paid $350 to replace the control panel. I wish I had just replaced it with a reliable product. 1 year into ownership and the seals on the door are falling off. May I suggest never purchasing a Maytag product?

I bought a Maytag dishwasher (Model: MDBH949AWS2) from Home Depot on 07 April 11 and it died 24 August 11. I called Maytag to set up an appointment for repair. The repair person showed up and stated that the control panel needed to be replaced. Apparently, if moisture gets into the panel it shorts it out. One would think that when designing an appliance that utilizes water and creates steam, it would be sealed. Anyway, the repairman explained that because the dishwasher was in a residential program, the warranty was null and void. I wish that someone would have explained this before I purchased it. I went online to AppliancePartsPro.com and ordered the part for $100.75 including the shipping cost. Then, I went back online to look up how to install the panel. The repair person said that they are charging $133.00 for the part and $129.00 to install. A small star tip screwdriver and 15 minutes was all it took to fix. From what I have read, this will not be the last control panel but, at least, I know how to fix it. Another thing that I know is that Maytag is off my list of future appliance purchases regardless of where Im using them.

I purchased a Maytag MDB7749AWW dishwasher in March of 2012. The electronic control on this unit failed in June of 2013 (3 months out of warranty). I have been trying to get a replacement part for over a month; the part is on backorder and unavailable. Whirlpool is unable to tell me when the part will be available. So, I have had no dishwasher for over a month and have no idea when, or if it will be repairable. Additionally this part is $150.00 and another $75.00 to have it changed. So it is going to cost me $225.00 to repair a 15 month old dishwasher that I paid $450.00 for. I have received ZERO support from Whirlpool. They told me today, 7-31-13, that the part is still unavailable and they will notify me in 3-6 business days as to if they can find a part. After seeing all the issues other people have had with this part, Whirlpools total lack of concern or support for the consumer and the cost issue it makes no sense to repair this unit only to see it fail again in a year or so. Basically I have a $450.00 boat anchor. The retailer purchased it from feels bad and is offering me another manufactures machine at a reduced price. Maytag has refused to do anything for me. I will never buy another Whirlpool / Maytag item again and I do intend to add my name to the pending class action suit.

If I can rate the AquaLift Technology oven cleaning system that my Maytag oven has as a “Zero”, I would. This technology only removes some of the spills on the bottom of the oven. It does not clean the sides or top of the oven. I’m back to the olden days of using a lot of elbow grease to remove splatters and spills. They say you cannot use any cleaners in the oven either. At least with the old ovens you can spray an oven cleaner and wipe it clean. This product has taken us back before there were spray oven cleaners!

Maytag Washer over 3 years old. Often problematic not functioning smoothly! Maytag invented this defective machine to intentionally rob the customer with all the probs that comes with it - poor design & quality, & not logistically programmed! Even aftercare/customer service SUCKS!!! Now, sensor spinning option is no longer working, drum not operational. No more Maytag!!!

We purchased the Bravos X washing machine on Feb. 9, 2012. I had a Maytag for 30 years before this one and did not have any problems. My model # is MVWX700X. I have given it sufficient time to get used to it. I have tried all cycles for my whites and am not satisfied. I use Clorox in the receptacle and I have only used Tide HE. I spot treat all of our underwear, which is changed every day, and it always comes out unacceptable. I am so disappointed since I was so fond of my old one and only thought I wanted another Maytag. At this point, I would never recommend this machine.

I emailed Maytag https://www.maytag.com/contact-us/ about my model number MBL2258XES3 Fridge on Dec 31. They scheduled a local appliance repair company and they came out today, Jan 5 and did the repair and defrosted the compressor and freezer compartment. 45 Mins is all it took. Thanks Maytag.

Maytag Bravos Model MVWB750wq1 - After only two years, the washing machine finally died. The machine was on a f51 code - hardly anything was in the washer. I also smelled a burning smell - well, that was the pump. The machine was not pumping water out. After the repairman came out, the contract company is saying they are not covering this because there was rust reported by the repairman. How can bearings inside a washing machine be rusted? This is a washing machine, isnt it? How are they building machines that deal with water and rust?! I will never buy another Maytag product - thats a promise. I spent over 2000.00 on this set. Never again.

My Atlantis dryer has never been able to be used on more/less dryer settings, I have had 4 repairmen repair my dryer 3 were while dryer was under warranty to fix the same thing 3 times wiring 4th time, anyway last repairman said my More dry wont work because I never had a sensor installed in my dryer and there is not a place for one so since 2005. Ive used timed dry only or my dryer runs all the time. I am concerned the first 3 repairmen never caught this. I should not have to be responsible for this either. Please have a manager contact me and have them check into my Atlantis Maytag dryer bought in 2005 and all the repair slips sent to Maytag.I used Green Yates in Joplin. Pretty sure. I thought I just had to live with it they would put new parts on I think timer, thermostats anyway can someone tell me for sure or inspect for yourself. I am single and dryer never used that much. Concerned Consumer, Nancy **/ Nancy ** as that name had front loader set from Maytag that I was very pleased with but sold with home in KC area, wish I had that set again I was very pleased .Thanks for your time.

I purchased a Neptune set in the late 90s when they first came on the market. I remember my delight - after the first use my clothes looked like new. Most impressive was I never needed to iron anything. Incredible. After 20 years of maintenance free operation, I finally decided they were getting too loud and was afraid theyd break down and spill water. Of course, I bought the latest version of Neptune again. What a disappointment. These machines are terrible. My clothes come out a wadded up, wrinkled mess. I have tried every recommendation in the book - the wrinkle free, the steam fresh, you name it. I have never ironed more iron free clothes before. Its added hours a week to my chores and we all look a frumpled mess. I really regret my choice. Strange that I cant wait for these new machines to break down so I can justify a do-over.

I was so excited to get a washing machine. My excitement quickly faded two washes in when I noticed that the clothes were not completely submerged in water. I checked the handbook and it said that this is normal but at the end of the wash I still had clothes that were completely untouched by the entire washing cycle. The first couple times that the washer was used, I noticed that the water took a very long time to come out. It said it was sensing and then the water would come out in small spurts. When the wash actually started moving, wow the noise was abnormally loud. It continued to make said noise for the entire cycle. I could hear it everywhere in the house. I am so disappointed in Maytag. My father is of a much older generation and he chose this brand based on his past experiences...now I have to tell him its a hunk of junk. Save your money and buy an old fashioned machine.