Dishwasher Model #MDB7609AWW2 - I have replaced the touchpad once a year for 4 years. Went online and learned a DIY repair using a Permatex Rear Window Defogger Repair Kit to fill in the touchpad broken circuits. I have repaired it once a year for 2 years. My suggestion is to avoid purchasing this product. Apparently even after multiple consumers have contacted Maytag regarding this widespread defect, Maytag has not issued a recall or assisted anyone. They say if the part can be replaced there is no issue. When the dishwasher works, it is great, however it WILL NOT last. Touchpad will fail and you will be out $124 for the part plus labor unless you do the repair yourself.

Dark clothes are left with residue on them, have to run another rinse cycle to get them clean. Been having this problem since we first got the machine. Anyone else having this problem or got a solution to fix it?

Can not wash 4 pairs of pants or 2 sheets because they get out of balance when the spin cycle begins. I had to take the clothes out and move them around to keep the balance. Very unhappy. Would not recommend this washer.

Maytag Bravos 300 Washer - Dont buy this washer! This expensive washer has been the worst household appliance Ive ever owned. We bought Maytag thinking we were getting the best. NOT SO! We could have spent half the money and got a better washer. Maytag is a brand of the past. Ive had this machine about 4 years and its been a problem since day 1. There is no soak cycle but I knew that from the beginning. The problems Ive had so far are: Not enough water so items dont get wet and have to wash again, Terrible wrinkles, torn sheets and garments, items still dirty, getting louder & louder, and the most recent problem is the plastic from the top edge of the tub is now shredding and getting sharp plastic pieces in my clothes.

I purchased a Maytag gas range about five years ago. After about two months, I noticed that the paint on the burner grates was flaking off. I called the company and they told me it was cosmetic. I have since bought two sets of replacement grates. I call the newest ones my dress grates, which I put on the stove when I am having company. I use the damaged ones for everyday cooking. Last year, the panel flashed. It locks constantly. And often, the door would not open, unless we pulled the stove away from the wall, unplugged it, and that cleared the computer. So, after months of unsuccessful door openings, the handle finally fell off completely. And the door locks whenever the oven is turned on. You have to finish your cooking, press cancel, and wait until the oven cools off, and then it will unlock. I have tried pushing aluminum foil into the latch hole on the door but have not been successful. Sometimes I just put a spoon in the door to keep it ajar while cooking. This cant be energy efficient. Of course, it is out of warranty. I saw a similar complaint about the burner grates. Also, the paint has chipped in several places on the cook top and the disks are all chipped. I am never ever going to buy a Maytag product. Oh, by the way, I called a repairman. I paid $65 for him to tell me that to replace the lock mechanism and the door handle, it would be $400. I can buy a new stove for that, but not a Maytag.

I have been very disappointed with the 2017 model of Maytag washer and dryer as the washer does not clean the clothes as it should. There is the inner part taken out with no agitator and I believe that is the reason that the clothes comes out not white or cleans as I am use to it being before with my other machines. I think they need to reinstall the agitator to clean the clothing thoroughly. The dryer takes longer to dry the clothing and it uses more hydro which cost a lot more monthly for us to have to pay out. I will never purchase another washer and dryer as this in the future.

I have not been satisfied with this Bravo washer since purchased 4 years ago. I have been holding back anger, hoping things would somehow improve. Clothes are never really cleaned, cant even fill washer with very many clothes because the washer goes off balance. It takes a lot longer to do laundry. Clothes spin so fast they are in knots when I put them in the dryer. I always have to iron clothes. Today, well today we have a leak coming from under the washer somewhere. So please tell me, what is the advantage to having a HE washer again? By the way, no warranty since its been 4 years. I will never buy another one.

A lot of repairs in 6 years from belts. It leaks water around seal on door. Only part of the cycles work. I would not recommend the Maytag washer to anyone. When I got it I expected or hoped it would last 10 years or more.

I need a new circuit board for a $2500 refrigerator. It was Saturday night of a holiday weekend when the ice chute started opening and closing and lights on door panel flashed like crazy. I called Maytag, who set up a service appointment for me for Monday. The tech came at 6pm and said there was nothing he could do without a part from Maytag and left. I proceeded to throw out all spoiled food and load a cooler with ice. I called Maytag, and they said it will take about a week to receive the part and have service. I have children in the house, and we live in Miami. I said that I would pay for overnight delivery of the part, and they told me it couldnt be done. I called this morning for a tracking number of the part, and they told me that it wasnt sent out as of yet. According to the internet search, this is a problem with a considerable amount of model number MF12568AES, and I should have been notified by the company. They claim it is a special project, not a recall.

Our circuit board has went out twice. The stove is not designed well. The oven vent sends hot air over the plastic panel / circuit board. It melts... The first one was under warranty and the second, only three years later, was not. This is a very expensive part and Maytag will not even talk about giving me a discount.

I bought the quiet series 200 dishwasher about 2 years ago. The control board went out and because it was past the industry standard one-year warranty, we were told we need to pay the cost of repair and parts ourselves. Well, I came here and seen that there were numerous complaints about that board specifically with all their models of dishwashers. I called and raised hell two times, and then I found them on Facebook and publicly bashed them there on their own page. They got back to me there and gave me an email address to explain my problem with their product. So I did. I even copied this web address and pasted it to my complaint. First, they called me and offered the part at 50% off. I told them, Go to hell. Even at 50% off the part combined with the techs labor, Im still better off buying a new machine and it will not be a Maytag ever again! A week after that another phone call came from them, this time saying they will cover the part 100%, but no labor. I agreed and for about $180 I got a new control panel installed and a one-year warranty on everything except cosmetic damage. Not bad, eh? Certainly not typical, I was told by the repair guy. Be angry, be respectful, but be persistent and public! That’s my advice.

I had a Maytag dishwasher (made by Whirlpool) that after 4 months of ordering wrong parts, parts arriving damaged, and parts that were re-engineered and did not match up, the dishwasher could not be fixed. The extended warranty people (AIG) promised me twice on a recorded telephone call that they would exchange my dishwasher, and after many many heated telephone conversations was given a 20 minute lecture on how the word exchange does not mean they will replace it. The frustration ultimately overtook my misspent loyalty in anything made by Whirlpool and I decided to accept the buyout of my extended warranty contract, at a loss of hundreds of dollars to me - well worth getting rid of that dishwasher and any further affiliation with Whirlpool corporation. Absolutely horrible customer service. Unbelievably god awful treatment. I dont know what happened to customer service at Whirlpool, but my dealing with them has convinced me that the term is an oxymoron at Whirlpool. Horrible horrible customer service. I have never been treated so poorly in my life. I truly dont know how they can still be in business if they treat their customers like they did me.

Our Maytag lint trap started falling apart a few months after we received it. Call Customer Service to get a replacement due to the product being faulty. The answer that I got from Customer Service: We sell you a new one. Poor customer service, faulty product. Dont buy dryer from Maytag.

I purchased a Maytag washer the centennial commercial technology model about 4 years ago. At the just barely 2-year mark it needed an all new transmission (Approx $800) Thank God for extended warranties. Now it is doing the same thing again making terrible noise. For a purchase of $1000 this is not good quality or decent workmanship And Maytag does not stand behind their product. I guess I need to buy another brand from now on. Please beware of very costly repairs with this one.

When I went to whip down the small shelve under the knobs, I cut my finger on the sharp metal. Was told that is the oven vent. Checked out your instruction book and found NO mention on that being a danger and to take care when cleaning. If I had been informed of that sharp metal piece I dont think I would have looked at your stove. The metal has razor sharp edges on both sides making it almost impossible to get too close to cleaning it. That shelf is a nice place to collect dust, grease and food boil overs and now I have to be extremely careful about cleaning. Thanks to someones not thinking in their designing. The stove is what I wanted other than that one fault.

Neptune 4000 washer - Worst washer EVER! Two weeks after we bought it sounded like a jet engine during the spin cycle. They replaced the bearing parts. Only cost us 450 in labor. One year later, again the bearing but this time we insisted on full coverage. 6 months later, here we are again! Most expensive washer in the history of washers and this is a KNOWN issue - yet Maytag gets away with it while consumers foot the bill! Ridiculous! Never again will I purchase their product and make dang sure everyone I know stays away too and everyone that hears my washer is in shock that it hasnt injured something or someone. Its only a matter of time!

Im have finally given up and purchased a replacement for my Maytag Bravos XL Top Loading High Efficiency Washer! The Maytag was 2 years old and I have ALWAYS had trouble with it. My towels became sour after 1 or 2 uses (sometimes they smell sour even before use!). My dark clothes ALWAYS came out of the wash LOADED with lint. I researched online to determine whether these were common problems and found several sites with suggestions such as: dont use more than 1-2 spoons full of high efficiency detergent (which recommendation I followed), Use white vinegar or liquid fabric softener. (I tried both with only minimal results.) ALSO use a dryer sheet in the dryer (I did this but it seemed like a waste since I was already using fabric softener in the washer). Dont overload the washer. (I didnt, but if I couldnt fill it, then why did I buy a washer with such a large tub ?!) Clean the washer monthly. (I faithfully did so, and tried alternating Affresh and bleach to see if theres any difference in the result... not really. Make sure you are fully drying the towels (I ALWAYS DID!).We had a Sears repair technician come to the house the last time my frustration level was overflowing and she only made me feel like an idiot, repeating some of the above recommendations and insisting they would solve the problem -- which, if they had worked, would have precluded my need to call a repair technician!!! The repair technician provided no other service or ideas to fix the problems. My husband decided we should go back to the tried and true agitator-type washer... bye-bye, Maytag Bravos.

Oven does not have consistent temp, cant change temp without preheating ruining whatever is cooking. 5 visits from Maytag during added warranty and never any satisfaction. Tough Microwave minutes and the oven goes off. Told it was a Govt requirement. Very noisy even after its off. Maytag wouldnt help or Home Depot either who warranty was through.

We purchased a 3K Maytag refrigerator/freezer and purchased an extended warranty as well. 5 months later the ice machine stopped working. We called Maytag to get it repaired since its under the 1 yr factory warranty and they sent an appliance service company they contract with to repair it. 6 service calls and two months later its still not repaired. I called Maytag back to say if you cant fix it please replace it. They say it needs to be deemed not repairable to even consider replacement and that they would send out a different repair company. As of yesterday (9/(9/14) another month and a half and 5 trips from the second repair company and it still does not work, so I call Maytag again to complain and they give me the same line ....needs to be deemed unrepairable... How long and how many service calls does it take to fix a ice maker? How much work and how many hours do I need to miss to get what I paid for? I went to their website and it talks about how their mission statement is customer service etc, etc, etc..... Thats just a bunch of lip service and judging by the HUNDREDS of complaints I have read this is their standard method of operation.... I for one will not let this go and will be filing a claim in small claims court to get what I paid for..... BE WARNED if you are looking to purchase a appliance.

I bought a refrig from Home Depot on 10-16-2012 two years ago and it doesnt work, but they only put one year warranty on. So had to go out and buy another. My complaint a refrig should last more than two years but they were going to send repairman out on my expense and more than likely would of cost me the price of a new one.

Bought this because it’s American made. It seems to be very glitchy. If you don’t use the detergent drawer it always flashes low detergent. The quick wash leaves soap on clothes. It acts up and leaves clothes too wet. No buzzer to tell you when it’s done. Have to hold button for 3 seconds to start. You can’t just hit button and walk away. Then wait for it to sense the load first to make sure it starts. Very expensive model.

Dishwasher Control Panel MDB7749AWM2 - Purchased unit on 11/22/2011. June of 2014 my start button stopped working, and after searching online I guess I consider myself lucky. Spent 38 minutes on Maytag consumer service site speaking to a rep who walked me thru a reset that did not help and then explained that my machine was no longer under warranty and $149 for the service call and the cost of the part assuming it was a control panel would total over $250 on a machine I spent $500 on. I spoke to a supervisor who was only willing to sell me a control panel at 50% off and do it yourself, and while they claim there are no consumer issues with this part, they stated that the warranty on the part is only 90 days. I told them this was the last Maytag/Whirlpool/KitchenAid appliance I would purchase and they did not seem to care so I will be moving on to another dishwasher since I will not invest $250 in a fix of an item that they will only stand by for 90 days!

I have an HE Maytag Bravos X washer and it cleans very well. But compared to my previous washer, with an agitator, I like the old one better and the clothes came out of the washer far less wrinkled. I would not buy another HE machine, given the choice.

I bought the dishwasher (Model MDB7749AWM) 15 months ago and paid $490.00. I had to put a new console in it ($245.00) on 07/16/2012. So that’s $735.00. Two days ago, the console went out again! I’m not putting $245 more in it! I called Maytag’s office. They more or less told me that was my problem! I am throwing that piece of junk away! And I’m buying a different brand. Maytag does not stand behind their product. Last Maytag I will buy! Warning! Do not buy Maytag!

Have not had either inspected, but last night the dryer started to rumble and then caught on fire... Fireman suspected bearing bad and caused a spark igniting dryer; washer has started making a shrill loud noise on the spin cycle.

Before putting clothes in dryer you have to untangle them. Sweaters and even t-shirts become stretched beyond help. Clothes smell like mildew if you leave them in the washer even just a couple of hours. Im 50 and had a few washer/dryers and these take the cake. Ive used the washing machine cleaner/refresher (something I have never done on washers in the past) and still a mildew smell. The dryer has lint on both sides of the lint screen. And as stated before if you dont untangle your clothes they come out in a big knot, partially un-dried & very wrinkled. The lint on both sides of the screen concern me - Ive never had a dryer do that before. Its not much lint on one side but enough to think something is not right.

This is a Maytag Neptune MAH8700AWW. This machine has been repaired a couple of times already and it has a will of its own. When it goes into that fast spin cycle that will kicks in and it starts moving. I wonder if someday its going to attack me. So, last Friday night we put a load in and it went into that fast spin cycle. It was making a noise like an elephant in labor so I looked in the laundry room.... Clouds of smoke were billowing out of the top of the machine. Our house will filling up with washing machine smoke! My husband stopped it, but I think it was a gnats hair close to bursting into flames. He looked into the front of the machine when the smoke dissipated and the entire gasket was in shreds. No more Maytag. Never. Im done.

I thought I was safe in buying Maytag for all of my appliances in my new kitchen. I bought a double wall oven Maytag MEW6630DDS. I bought it in late 2010 and have had no issues until August of 2018. I rarely use the bottom but used it in August of this year to cook cupcakes. After baking them and leaving the kitchen for a short while I heard a loud explosive, shattering sound. I walked to the kitchen to see that the bottom oven door had shattered into a million pieces. Thank the good Lord that I was not near it. I contacted Maytag to see if there was a reason it would have done this. They said that there had not been a recall. They sent a repairman at no cost to look at it. He came, took it apart and had no reason for why it would have done this. He left it in pieces and said that he was ordering the replacement door. Maytag advised us to turn off the breaker to the oven. After a month without ovens, the repairman called and said that the part had been discontinued. HA! You think?!? It has the potential to explode. It should have been recalled, not just discontinued. Maytag offered us 20% off a new set of $3000 wall ovens or $150 to pick ours up for disposal. Talk about saving the company money and screwing over the unlucky recipient of a defective product. They ought to be ashamed. I am going to have to replace the broken glass with aftermarket glass. What is going to happen when I use the self cleaning option? What happens when the top door explodes. I am scared to use my very expensive wall ovens that I thought would last at least 10 years. Shaneka at Whirlpool said that people have appliances fail all the time and just have to buy replacements. Do all of them have to replace ovens because doors explode for no reason? I am not the only one this has happened to. I have found several other complaints of this on the internet. Why did they discontinue these door? I wonder.

I bought a Maytag Bravo without an agitator. Regretted from the 1st load. Some of my clothes do not even get wet and I bought the commercial grade. My 20 year washer that was on its last leg washes better than my brand new Maytag. Please do not waste your money, your clothes will not come out clean.

I purchased a Maytag dryer several years ago, not a fancy one but just a plain simple dryer (model number MDE2706AYW). Thank goodness from the other complaints I have read I didn’t buy one that is computer controlled. The heating element has burned out twice, main thermostat and limit thermostat has burned out, and if you look close, it seems the wires are trying to melt or at least the insulation. Well, the insulation is melting. And the venting system is cleaned regularly so they can’t blame that. The last dryer I had lasted well over ten years with zero problems. I should have just fixed it. I’m sure I wouldn’t have spent as much money on repairs as I have with this one. You remember that lazy Maytag repairman that was on TV for so many years, you know why you don’t see him any longer? He is at my house repairing my ** dryer! You never, never hear me say this but the next dryer I buy will be made overseas. My last appliance purchase with any of these name brands on them: Maytag, Jenn-Air, Amana, Admiral, Crosley, Magic Chef, Performa by Maytag, and Norge.

This Maytag Centennial with commercial technology washer has ruined a couple of thousand of dollars of clothing, maybe 10 to 12 of my favorite shirts (ripped holes around the top of the pockets), bath towels and sheets and comforters and hand knitted small blankets that can never be replaced. It tore holes in nearly everything that was made out of cotton, I was doing spring cleaning and I normally wash most of my summer clothing, but this time this washing machine destroyed nearly all my summer clothing. This washing machine came with the house I just purchased. (I gave my older Maytag washer and dryer to some needy folks which worked great when I moved here). Disappointed in MAYTAG. Will never buy another Maytag!

I purchased my Maytag side by side Model No. MSB27C2XAM00 in August of 2013. Within a 2 Weeks the lettering was gone on the control panel for the ice and water dispenser. I contacted Maytag and they replaced it, but the next one did the same thing, and the next one! They replaced it three times and they have all done the same thing. Now they are refusing to do anything more because they say I must be using cleaner or something on the panel because I am the only one having an issue with this! I assure you I have not used any cleaner and there are only three people in my household so it doesnt even experience excessive usage! I know this problem isnt as extreme as some, but when you pay this much money for an appliance you would like to think it should last longer than this!

The performance of the refrigerator is disappointing. It was difficult to find someone to repair it when the freezer fan motor went out. It makes noise, shelf space is insufficient. Temperature mechanism often doesnt work properly.

Havent even used the range yet and the paint is peeling off of the top. I have had the repair guy out. The new top piece of the range arrived with peeling paint also. I put in a claim to have the range replaced and was told they would contact me in 24 to 48 hours. That never happened and so I called again. They said that they would call and, of course, it didnt happen. I paid $1,300 for a stove that looks horrible with the paint is peeling off of it. What kind of ** is Sears selling? Maytag is owned by Whirlpool and nobody wants to make this right.

My Maytag 2000 has ripped our clothes. This is my 1st front loading set. I looked on the internet and it seems that this is a known problem. Very upset that a brand that I had for 30 years and recommended to others as well has turned into a terrible company. Im a single mom and Im not in a position to replace a washer every year. I trusted Maytag! A recall and either replacement of the parts, or delivery of new part to fix the problem should have been put in place. I wrote to Maytag to see if they will do something to fix this problem.I have the set, washer shakes a lot, but works well. Washer also always has a lot of water left on the door seals folds, terrible design... I will post on other sites to warn other customers. This is not OK, my clothes are destroyed. See pictures. Clothes got trapped in a gap that exists in the perimeter of the opening, where it meets the door. Why is there a gap at all???

We bought a Maytag Bottom Freezer Model MBB1952HEW in 2006. We have already replaced the relay, two years ago, now the compressor is going. I have seen recalls of the top freezer on the internet but not on the bottom freezer. It is concerning when you pull your refrigerator out from the wall as to how warm/hot it is back there. We were told it would be cheaper to buy a new refrigerator versus replacing the compressor. We are so disappointed in how much money we have stuck into this refrigerator for how old it is. I would expect a refrigerator from a reputable company to last longer than 6 years.

I purchased range in January of 2011. I have had the top replaced and still it looks bad. Every time I use a burner, even if boiling water, I need to use the razor scraper to clean the burner. I’m very dissatisfied. We used to say we would buy nothing but Maytag but not anymore. Tell anyone who will listen how much I hate this stove. Oven does not cook properly, burns most everything I bake no matter if I lower the temp and time!

My Bravo washer will not wash a set of sheets without dancing across the floor. So irritating to have to run in and separate the sheets that have ended up in a ball. The dryer is ok. Except my old Maytag had a loud buzzer that went off when the cycle was done. My new dryer has a dainty little chime that cant be heard if the washer is going. Wish I had my old set back!

We purchased both a new Maytag washer & dryer in 2011. Our dryer, Model #7000XG1 all of the sudden started thumping when we were drying our laundry. After we called a technician to come out, he stated we had a crack in our drum. How in the heck does that happen in 4 years time and only laundering for 2 people? Of course this steel drum should not wear out before the other parts, but it did. Since there is a backorder on the replacement drum, it makes you wonder if this problem is wider than it seems. Also, Maytag would do nothing for us other than offer us the purchase of a new dryer at a discounted rate good for only 7 days of their offer. Seriously, how about standing behind your product? And, then again, why would we be enticed to spend that kind of money on the same type of product that has flaws? Uh, duh Maytag or Whirlpool. Silly fools you are.

We bought our Maytag Neptune washer in 2005. We chose Maytag because of their reputation, their headquarters in Michigan, and because looking at the machines in the store, they seemed to be well built. Were we ever wrong! You would think paying $1000 for a machine would get you a product that lasts longer than 8 years! Our other washer (a Whirlpool) lasted 20 years and was still working. Im now consistently getting a 3e error code. In searching online, I found that this is a pretty universal problem and thought maybe Maytag had a recall on it. What a waste of valuable time. I did find out the machine was actually a Samsung. This seems like fraud. If I wanted a Samsung, thats what I would have purchased! Contacting Maytag Customer Service was like Land of the Stupid. After getting the runaround and being sent to a phone number and website that only covered Samsung I called Maytag again. I was put in contact with another person who could supposedly help me with the recall. Even though I told him what the problem was, he gave me the robot response about sending the GFCI plugin and told me, That should make your washer safe to operate. Seriously??? I replied, This wont fix the problem because THE WASHER DOESNT WORK and we got the recall part long ago. He then wanted to schedule a repair appointment. Not doing that, considering how stupid the Maytag reps I had talked to so far had been. Putting the hubby on the case, luckily hes pretty handy. On the upside, it was fun responding to the Maytag customer service survey that night, LOL. All of our other appliances are Maytag and they have all been great, but this washer is an unreliable piece of junk.

I bought a Maytag Bravos washer and dryer two years ago. A week after the one year warranty was up, my dryer broke. That was in October. It took me until February to get it fixed, but within two months it broke again. It has taken me until now to get it fixed again and they found the same problem; the thermal fuse blew. Both times it has cost me over $100 to get fixed, but I still cant use every part of the top panel; I can only use timed dry cycle. I’m expecting the dryer to go again. The repair man had to re-glue the seal that went around the drum. The vents were all clean and were blowing fine, so we’re not sure why this keeps happening. Our family have always owned Maytags and they have always lasted for 20+ years. I am so disappointed with Maytag at this point and will never buy another again. Go back to the old days, Maytag! By the way, has anyone noticed they dont run the Maytag commercials anymore, because I have!

Purchased Maytag front load washer model MHW6630HW from Home Depot. Machine was installed 9/15/19. From inception we had issues that have escalated. Machine leaks and makes strange hissing sounds. Home Depot has no record of the purchase in their website now. We tried to return it within days. We contacted Home Depot executive offices and they keep sending Paradise Appliance repair. The repair people do nothing and keep saying we have to come back again for you to be considered for replacement. Home Depot is dragging their feet and we are concerned about the six month deadline. The Maytag does not do an effective job washing and clothes comes out wrinkled. Concerned about the sporadic leak getting worst and doing damage to floors.

This dishwasher was here when we bought our home. It has been heating up way too much on the drying cycle. I turn it off and air dry the dishes but today I noticed it melted my plastic measuring cup. I had the heat turned off and opened it as soon as it started the drying cycle.

The washer drum fills up with very little water, very little. I can do an entire load of laundry and the stuff on top doesnt ever get wet. Went on Spring Break in Florida and a month later our clothes still smell like the beach. Grill out, and I smell steaks the next time I put on the shirt. Stain your clothes in any way, its there forever unless you hand wash it first.To get it to work at all, each time I have to start the wash cycle (I leave the soap out just to save it for the next start), let the drum fill with water, pause it, get all the clothes wet, then cancel the cycle. After it drains and the machine is off and full of wet clothes, then start it all over again adding soap this time. On the second try, set at deep cycle, it will add enough water to cover the clothes - Im guessing because it senses more clothes because the clothes are now wet from the first, cancelled cycle. During the wash cycle, Ill open the lid and robustly move everything around, almost hand washing. #Handy. The dryer is fine, Im keeping it. The washer, cant return it - been three months of this frustration (kept believing it was me, reset it multiple times, change the settings, tried everything). Im buying a new one and throwing this junk out. $700 lesson.

Washer needs new transmission at only 3 years old! Maytags 10 year part replacement doesnt cover it. The company actually asked why I didnt purchase extended warranty, I thought I didnt need one. Bad bearings, it doesnt wash the clothes clean, $400 to fix it. Needless to say Im buying a new washer and it will not be a Maytag, worthless piece of scrap!

Gemini Twin natural gas range - I bought this range approximately 18 months ago. I thought it had all the features I needed and it looked good -- looking good is just about all it does! If you are a real cook I would suggest you avoid this range. The burner controls are preset and it is impossible to turn the flame very low if a simmering heat is required. If you are making meringues, again, the oven heat cannot be turned to a cool enough temperature. Ovens bake/broil unevenly. It takes forever to bring a pot of water to a boil, not because the flame is not hot enough, but because the pots sit far too high above the flame. Bad, bad design. Probably designed by someone who eats take-out!!

I positively HATE the new BravosXL Maytag washer, which has no decent agitator. It is ruining my clothes, as it spins with little water and leaves soap residue all over the clothes. Additionally it puts large, long wrinkles in my knits, especially disfiguring slacks. Maytag must have known how rough and ruinous this washer was on knits BEFORE selling it to an unsuspecting public! I want my money back in order to purchase an old-style, well-functioning agitator washing machine.A class-action suit should be brought against Maytag. There was no way to know before buying and using that this machine is horrible!!!

Model MDB4949SDZ0. 7/10/2018 Purchased from Costco. 7/23/2018 Installed by company arranged by Costco. 6/18/2019 A burning smell was coming from front control panel area of dishwasher when it was turned on. 6/25/2019 & 7/3/2019 Repair technician came to fix but could not find anything wrong so burning smell continued whenever dishwasher was one hour into cycle. 7/12/2019 Repair tech changed out front control panel because burning smell was still coming from handle area. 8/9/2019 Dishwasher does not drain completely when wash cycle is complete. Sometimes there is sudsy water left, sometimes it is clear. The water level is above the heating element at bottom of dishwasher.We only run the machine 2-3 times a week and have been using different cycles to see if the draining issue is with one cycle or all of them. No matter which cycle is used, water remains at the bottom of the dishwasher above the heating element. This seems like way too much residual water. Repair technician is scheduled to come for the 4th time to look at dishwasher but we just received a message that we will have to pay $129 service fee because dishwasher is now out of warranty. Maytag, fool me once, shame on you. Fool me twice, shame on me. Therefore, know that we will not be purchasing a Maytag product ever again.

I have a Maytag fridge/freezer model number MFF2557 10403089ER. The freezer keeps going out. The repairman replaced the computer board called a jazz board stating that the bulbs in the fridge part are too close to the board and the heat can cause the board to short out. He suggested switching bulbs to 25 watts which cannot be found for fridges. The freezer continues to go out and sometimes restarts itself or by flipping the breaker switch, brings it back. In the meantime, food is ruined. Yesterday, he put a new starter relay on the compressor stating that this series of fridge/ freezer has had a problem with the compressor and Maytag will not take responsibility for this. There is no recall at this time and we are waiting to see if this corrects the problem or if the freezer will continue to go out. Thank you for your help in this matter.

We purchased a Bravo Maytag series top load washer from Sears in June 22nd 2013. See receipt for verification of sale. It seemed to be alright and we were hoping to be a lucky consumer, but now it is January 2015 and today I could smell smoke along with a weird smell (like an auto repair shop smell). I immediately was concerned about the entire house catching fire. Luckily I figured out the smell was coming from the washer and was able to pause it, stop, and then turn off. We are not happy. Our whole main level smells awful. And Im pregnant so this is probably not good to be inhaling. We are looking for recalls that may be out but weve only seen front load recalls not top loaders. When we bought this it had great reviews, but now it appears there are so many complaints, so my question is: Why isnt Maytag doing something about this massive problem?

We bought a new Maytag top load washer March 2018. July of 2021 it starts making the worst racket Ive ever heard. I thought at first that there was a dog being killed by another animal. As I ran to the door I realized it was my washer. Long story short, repair guy said itd be cheaper to just buy a new washer. Maytag did nothing to help us resolve the issue of a 3 yr old machine totally useless. We bought this machine because we thought it would last for years. I mean their commercial shows the repair guys doing nothing because Maytags never need service. My new machine is not a Maytag. No more Maytags for me.

Purchased the Maytag Bravos washer approx. 2.5 years ago. I cannot even begin to describe how disgusted I am with this washer. My clothes i.e. towels come out ripped on the edges, clothes do not get clean, shirts etc come out wrinkled no matter what setting used. It is not energy efficient because loads of laundry need to be washed twice if they are soiled (like our everyday jeans). Went back to the independent store where I purchased washer and was told to use only the bulky or gentle/delicates cycles to reduce rips in clothing. Such a complete waste of money, and it was not cheap!

My husband and I purchased a brand new Maytag dryer in January 2012. Our first issue came when the sensors went out in March; then the belt slipped off the drum in June; then the thermistor was defective in July; and now, the same thermistor code has popped up twice since replacing it. I cannot afford to go to the Laundromat all the time thats why we bought a new dryer. Please give me a refund so that I may buy a different brand. Model number: MGDB850WR0, Serial #: M10301051

I was all too excited to FINALLY own a new set! I conducted research and read reviews. We decided on the Maytag Bravo XL set (Lowes) and was thrilled! For the first 6 months. They were both fantastic! 6 months later, several times the clothes washed were soaking wet as if they had been set on soak. It continuously alerted to clean after 3 loads. The dryer... Well, evidently, if you live in a high-humidity region, DO NOT HOOK TO THE WATER LINE FOR THE STEAM OPTION. It will soak your dry clothes! After 3 loads of drying, it fails to re-start for the 4th load for at least 12 hours! When paying over $1,590 for a new set, this should not be an issue. Mind you, I do laundry once a week - 5 to 7 loads including linen. Fortunately, we paid an additional $200 for the warranty at Lowes.Lets see what happens there!

I had another Maytag washer. It lasted 21 months. BB got me the BravosXL to replace it. I have had it 6 years. It is a piece of junk. Goes out of balance all the time. We are 2 ladies and don’t have heavy clothes to wash. I am washing now. I have put It through a wash cycle. The soap is still on the clothes. I am on my THIRD rinse cycle and there is still soap on the clothes. And I used less soap. Never again MAYTAG.

This dishwasher is extremely quiet and very attractive in the kitchen. Easy to use and does a great cleaning job. The price was also right. Would definitely buy again.

The new technology on the washers is useless and saves no energy or water. People figure out how to get more water in the tub and use that setting. There is not small or medium water fill anymore.

We bought our washer/dryer from Home Depot and felt Maytag was a good bet. Guess again. Washer is running fine for now but after light use (about 3 loads per week) dryer failed. With no warning, I heard a loud pop about 3 min into a cycle and overheating. If I hadnt been home might have caught on fire. Good for us we live close to a coin laundry so in no rush to replace but can bet when I do it wont be Maytag and thats too bad. One of the few makers still building in the USA but thinking Samsung is looking good. This is the Maytag 2000 series btw.

I was so excited to get a washing machine. My excitement quickly faded two washes in when I noticed that the clothes were not completely submerged in water. I checked the handbook and it said that this is normal but at the end of the wash I still had clothes that were completely untouched by the entire washing cycle. The first couple times that the washer was used, I noticed that the water took a very long time to come out. It said it was sensing and then the water would come out in small spurts. When the wash actually started moving, wow the noise was abnormally loud. It continued to make said noise for the entire cycle. I could hear it everywhere in the house. I am so disappointed in Maytag. My father is of a much older generation and he chose this brand based on his past experiences...now I have to tell him its a hunk of junk. Save your money and buy an old fashioned machine.

The washer and dryer were purchased together as a set 4 years ago in 2010. There have been times where I actually had clothes come from the washer completely and partially dry due to lack of water inside the washer! It fills based on how many clothes are in the washer or capacity that it senses. I have had so many clothes dry washed and torn up due to its use! If you set the washer to the wrinkle control position it does not go through the last rinse and spin cycle, you must reset it to the rinse, drain, spin cycle again in order to finish processing that load.It has already thrown its belt 2 times! Which my husband had to fix since we could not get in touch with anyone at Maytag who knew what we were talking about! If change gets stuck inside the washer bin in the little groove in the tank it is very difficult to get out, Im sure everyone has washed a pair of pants with the change still in the pockets, yes I know this is user error but if you dont know the change is in the little grooves because you cant see them, it stops the washer! So be sure to search this every time you do laundry!The dryer has a mind of its own! Sometimes it will finish drying your clothes, sometimes it wont finish the time set! Theres no reason just doesnt finish! There is so many reasons I will never purchase this brand again. Ive run out of room and patience. My clothes look like Im homeless!

It was alright for a while. Then it started ripping up my clothes. The machine is not overloaded, enough water has been added but, when I take the clothes out they are torn. Not a good experience. I have seen several reviews on the Centennials, none of them good. What is the problem. I am hoping my experience gets resolved.

Maytag #mbl2258es1 - started leaking in the freezer two years after I bought it. Two service men who did not know how to fix it. Now the refrigerator is not cooling. No more Maytags. Horrible refrigerator.

I purchased Maytag washer/dryer set in Feb 2021. In June the washer broke. It took 2 weeks to get repair person to look at it. During the appt no faulty product was identified so they dont know what to replace. No parts were available. A follow-up appt was set for 1 month later. No parts are available to make the repair so a follow-up appt would be futile. . The only communications other than No Parts is that they want me to purchased an extended warranty. I will never purchase another Maytag product or recommend them to anyone. Meanwhile my warranty continues to time-out and they dont have any parts or idea when they will be available. Im not sure how a company can sell products that they do not have some level of support for those products. Beware of purchasing Maytag Products.

We purchased the washing machine (MVWB400VQO) on July 9, 2009. Now we must buy a new washing machine as this one is apparently beyond repair, or else the repair costs will far exceed what it would cost to purchase a new machine. We are completely disgusted with its failure, as we paid $822.36, with the delivery fee and the tax. We expected that this machine would last for years, but here we are, 42 months later, having to again invest in a washer. Now that we have a computer and are able to browse your performance reports, we wish we had been able to read them before, in which case we never ever would have bought it at all.Yesterday it spewed water all over our basement, flooding things that should not get wet, providing an atmosphere for encouragement of mold and rust. The motor is gone as the housing is cracked, which was caused by debris getting into it, something that we could not have known or prevented. This is very poor design by your company, in our opinion. We called some repairmen, all useless as apparently the whole machine would have had to be completely dismantled at a rate of $84.00 per hour, and he could not tell us how many hours that would take, to say nothing of finding a new motor for the thing.We will never again buy a Maytag product as they are expensive with a too-short shelf life and there’s nobody who cares when you need help for something that should not have happened at all. I understand Maytag is really not the good old dependable Maytag we used to know and love at all, but rather is now owned by the Whirlpool Corporation, whose products we will never purchase either.I know why that lovable old Maytag repairman we used to see on TV is retired. Its because he could no longer stand the quality (or lack thereof) of the appliances that you are now producing. He is probably home, hiding his head somewhere and hoping nobody will recognize him. And what, kind sirs, do you have to say about this? Thank you in advance for your prompt reply.

Maytag Bravos washer and dryer both need replaced in 3.5 years! Control board had to be replaced on washer in under 2 years and now the replacement went bad in about 15 months. Maytag can’t help! Hundreds of dollars wasted. Dryer is not much better as the control board is now malfunctioning! DO NOT PURCHASE MAYTAG!

I have a bottom freezer Maytag refrigerator that is about 4 years old. It started leaking and continued to get worse fast... It appears that the gasket around the freezer drawer does not seal about half way up. It causes a sheet of ice inside the freezer, so I am not sure if it leaks due to the ice defrosting. The refrigerator doors do not seem as if they shut tight either. After reading many of these comments about Maytag refrigerators, I am not sure at this point if it might be better to buy a new one rather than fix this one??? I looked for a recall and do not see one. Clearly this is a defective appliance.

Products spoiling even if set at recommended temperature. Hard to clean bottom freezer. Not happy with this configuration. Had to have repairmen in because of stopped up drain which I could not access to clean myself. Does not close completely at times.

My Maytag range from the 1990’s is the easiest to clean top of the range I have ever had. Controlling the temperature of cooking is very easy. The oven is not as responsive As it takes about 10 minutes to preheat. Once heated it maintains an even temperature.

At 14 months old Main computer box failed, caused the machine to shut down on unbalanced load ($400). At 28 months old Main computer box failed, caused the machine to shut down on unbalanced load. In addition when the service guy was underneath the machine to change the module he noticed the stator housing to the motor was falling off. He said he never saw anything like it. After reading about all the problems people have with these machines I have talked friends and relatives out of making the same mistake of buying an old and trusted brand like Maytag. .

Worst product I ever purchase. I have four kids which are boys. This washer does not clean very good. I usually soak the clothes first before I put it in the washer. Never purchasing their product again. Now I am stuck with this washer because I cannot afford to purchase another one. Hate it.

I bought a set of 4 Maytag kitchen appliances. Terrible quality. Dishwasher racks poorly designed for anything except standard size dishes. Microwave has a hotspot and explodes whatever Im reheating. But refrigerator is the worst. According to my service man, Maytag is aware of known issue with poor quality evaporator coils that erode quickly, leaking freon. Causes problems with ice buildup in freezer, poor ice production until it loses enough freon to stop chilling correctly causing food spoilage. Im to that point now. This fridge is only good for offshore fishing site. Whirlpool is aware but will stall as long as possible, then refuse replacement, but they will offer to help you replace the appliance. HA! Fool me once, shame on you. Twice, shame on me.

Maytag Bravos XL he Washing Machine - Having owned several Maytag washers in the past, I thought this would be perfect, instead, it is the worst washing machine I have ever had. This machine does not clean well at all, spots on clothes stay put. I have tried different amounts of HE detergent and clothes are twisted and wrinkled terribly and have remaining soap residue on them, even when I use less soap than recommended. I wish I would have returned this machine immediately after a few loads. It doesnt get better with time. It is very loud, but that is the least of its problems.

Washer model mvwc200bw1 c43942055 -Worst washing machine ever! The clothes come out all twisted together, I cant even see how the washer works because the lid locks when washing! The sound the washer makes while washing sounds like its barely even washing the clothes! I will never purchase any Maytag products and I wish I could return this one!! So disappointed, Im sticking with Whirlpool!! Plus the clothes dont even get that clean!!

I purchased a washer and dryer model MAH8700AWW. In 2005, I purchased the extended warranty. In 2009, I had to replace the main control board and motor on the dryer. Now, I find out that the washer has a warped drum which caught on the door boot and messed the shaft up. I didnt know that it has probably been that way since I purchased it because every time I washed clothed, I had to stay in with it because when it would go to spin, the washer would walk out into the middle of the room. I called about it and they told me to put rubber pieces to hold it still. Now it is going to cost $ 821.95 to fix. That is more than I paid for the washing machine and Maytag will not help to fix it. I would like someone to contact the company and find out why they dont stand behind their products anymore.

Just purchased/used the washer. One needs water to wash clothes. I added water to the machine just to get the clothes washed. How can this pass any reviews when it does not use enough water to clean a set of sheets? Not to mention rinsing. Does anyone wash clothes in the group that designed this machine?

Preheat the oven, put in the food. Oven does not maintain the temperature. Gives me a code of F2-3. Want to know what part needs replaced to solve this problem. If anyone can relate to this problem or help me with information please respond to this or email me.

MDB7749SBW - Purchased a new dishwasher from Home Depot & had them install it. It worked for 6 1/2 months & the control panel blinked & went dead. I did some research & found there were a lot of problems with the control panels & even a class action lawsuit. I went to Home Depot & they said contact Maytag & brushed me off. I set up a repair per warranty & all was fine for 10 months & same problem has happened again. I told them at Home Depot to replace the unit since nearly every repair job on the control panels prematurely fail again every time. I am going back to the Home Depot again. I do have older Maytag appliances that perform as required & I do know Lowes would have replaced the defective dishwasher.

We purchased a Maytag Washer and Dryer from The Home Depot in September of 2017. We did not purchase the extended warranty because of our confidence in the brand. Within less than a year, both appliances started making noises. By September of 2018, the washer sounded like it had a bag of mice squeaking inside every time we ran a load and had stopped spinning entirely. I called and spoke to a very kind lady who assured me that even if we were outside the one year manufacturers warranty, they would offer us the extended warranty without question because it was so close to the one year purchase. She took my credit card, we were charged for a five year plan and service was scheduled. After service, both units were still louder than I would prefer but the technician said it was common. Over the last few months, both have become louder and louder. Now the dryer shuts off and wont stay on. When I called back to schedule service again, the date of our purchase was all of a sudden in question. (I applied for the contract over the phone so THEIR rep entered the purchase date.) They are now telling us they will only honor the cost of parts and we are subject to pay for diagnostics and labor (which is the largest cost of repair). They are telling us our contract has to be cancelled and AFTER we receive and PAY FOR all but the parts, we can call and pay for a NEW contract. This has been the WORST appliance purchase we have EVER made and we have lost all confidence in the quality of Maytag/Whirlpool appliances. Both units have been VERY disappointing and we spent over $700 on each unit. NEVER AGAIN.

This is the worst washing machine I have ever had in my life. Machine started bouncing during the wash cycle and also the spin stopped. Never in my life have I had a machine fail on me like this one. I spent a lot of money on this. This machine should be recalled. I read up on all the complaints. Its a model #Tw6600TQ0.

I bought it from a local dealer so that I could get it serviced locally. I bought it in 2012 and paid $750 for it. I hate just about everything about this (and all modern) washing machines. The deal breaker is all these safety features that are really inconvenient and pointless. If I could have found a good used washing machine at least 10 years old, I would have bought it. This is a Maytag Centennial. I dont like the automatically locking door, the inability to choose the water level myself, and the requirement to use a particular kind of soap. Also, I hate the idea that I have to clean the washing machine from time to time. Whoever heard of that? But you have to do it otherwise your clothes will have a sour smell. These new washing machines are not an advance in technology. I may have to go back to using a wringer machine.

Maytag Cenntenial Washer - We traded our super capacity for the ex-large Maytag washer and we have great regrets. We posted it on Craigslist about 4 months after we bought the unit and NO ONE would buy it for $300.00 even though we paid close to $600, and only 4 months old? What does that tell you? I have had to add 5 gallons (bucket) with each wash to make sure all the soap washes out. Very loud, takes a long time to wash and just worthless. This last weekend, we tried to trade it for a used $150 agitator washer with a used appliance store and they said theyd never be able to sell it and refused the trade. What does that tell you about the washer?

I purchased a washer/dryer, Maytag from Home Depot Nashville. It was delivered and set up. 02/24/17 the date of purchase, delivered 03/07/17. I have tried in every way to get the washer to wash properly, but to no avail. The water level doesnt cover the clothes, it takes 10 to 15 minutes for the wash to begin its cycle. It doesnt spin the clothes dry enough to put into the dryer. The washer makes all kinds of sounds thats drives you nuts while setting up to not wash your clothes clean. I have contacted Maytag on several occasion about this problem, they sent out someone to service the washer. Now, why would a brand new washer need servicing. Somethings wrong. It isnt functioning up to standards and they should give me another washer.Now on 05/18/17 the washer was serviced, I have called them again to do something about this piece of **. I was told that the only thing they could do is come service it again. Why, must this brand new washer be serviced every week. It doesnt make sense... I dont want this machine, I want my money back so I can purchase a machine that will wash my clothes properly. I purchased a secondhand washer and dryer from a used appliance store, it lasted my family 10 complete year. The only reason I dont have it now is because I wanted to upgrade, since I have never had a brand new set. What a disappointment. Everything that looks good from Maytag isnt good. I dont understand why they wont stand behind their product.Somethings got to be done about this. Maytag will not take my money 1,200 and force me to keep this malfunctioning piece of nothing. Im going to Youtube this product so the consumer can see how this product doesnt work properly, therefore they wont waste their hard earned money. I will be contacting the BBB Nashville, and wherever I need to. I will let the consumer know the make and model of this product and where it was purchased from. Maytag I want every penny back. And, should hold you responsible for ever time I have had to go to the wash house because my brand new set wont work, and your company wants to service it every time I try to wash. I purchased this appliance on the strength of the well known name, that was the wrong thing to do.

WOW, I cant believe a group of educated professionals made, tested, and approved such a washing machine. What a piece of crap. I could put my clothes in a bathtub and let the kids jump up and down on them and they would come out cleaner. I would love to have a heart to heart talk with the engineers who designed this, to ask, What were you thinking. What a waste of money, and a once good company, that will soon be going out of business.

We purchased our Maytag Bravos just under two years ago. Over the past month or so, we noticed the spin cycle was getting louder and louder. Today we had the service man come out. He informed us that our 2-year-old machine will require new bearings and a new basket, which equates to over $700 in repairs. The repairman said he has seen more and more of this with these high efficiency washers. He suggested that anyone buying these new washers be sure to buy the extended warranty.I for one am completely disappointed that one can spend that much money for a washer with a two-year shelf life. I personally think this is planned obsolescence created by the manufacturers. The serviceman also said the LG versions of these washers have a large increase in electronic problems. Be warned, we have very few choices these days so buyers beware.

Bravo Series Washer and Dryer. I hate, hate, hate this washer and dryer. I have had it for 2 years and hate it more every day. What makes is worse is the over $2,000 spent to buy this piece of crap technology. The engineer should be fired and sham on Maytag for selling such a piece of crap. Washer does not get clothes clean and I have pictures to prove the amount of dirt and lint and soap left on clothes and bedding. Very poor design, and worse yet absolutely horrible engineering.To wash one item on delicate takes 47 minutes. No way around it and you are limited to the water temperature you want to use and the spin cycle that you want for that item. Water level is too low no matter what setting you use. I have read and reread and gone step by step according to instructions with no success of clothes coming out clean. Clothes are also twisted and knotted and wrinkled like no other machine I have used in over 50 years. The washer is very limited in what it allows you to do. Bedding cycle is a joke that does not work at all. One of the reasons I bought this was so that I would no longer have to take the time to drive to a laundromat. I washed a comforter and so much soap and lint and dirt was left on the comforter. I still had to take it to the laundromat to get it clean.Dryer is just as bad. Even with the energy saver off it still takes 1 hour and 20 minutes to dry 4 towels that are 5 years old. I cant imagine how long it would take to dry brand new fluffy towels. It was engineered to sense when ONE piece of clothing is dry. I want ALL my clothes dry, not one piece and the machine shut off. How stupid is that??? Engineers - design it so it senses when clothes are still damp and the machine keeps running!!! I can only use the time dry setting because no other setting even comes close to getting the clothes dry.To top off the hatred of this machine some damn engineer apparently thought this was a car and needed to be aerodynamic with a curved lid on both washer and dryer so you cannot put anything on top of the machine!!! Not every house is 5,000 square feet with plenty of room and storage!!! They want to force you to buy the drawers to put underneath and then the washer becomes too tall for short people to reach down into to get the clothes out. There is not one positive thing I can say about the washer and on top of it I will never purchase another item from the store I bought this set from. I have had service come out time and time again and they say it is an installation problem. Installation says it is service and yet no one will admit it is just a very poorly designed machine. Do not buy this brand or series of washer and dryers. This series deserves a minus and the company should replace every set sold!!!

I like my fridge. Its a old one and still works. Its been very reliable and have never had a problem with. I dont think I would ever purchase a different brand for Maytag is the brand for me. They last for years.

Model# MVWC200BW1 bought in 2015 tangles/stretches clothing. This machine is/has been a true disappointment. The agitator wings are not attached at bottom allowing clothing to get caught and as the agitator turns, so does the clothing causing stretching and severe tangling. Poor design compared to the agitator that would rise and fall - those got clothing clean and did not ruin them. I cannot trust this machine to moderately cost clothing for fear of their demise. The lock-down mode is not convenient for those last minute added items. Will not be buying Maytag/Whirlpool ever again when another machine is purchased. This is a piece of rubbish!

We bought the Maytag Bravos XL washer 6 years ago when we moved into a new home. We have a large family and after reading many reviews, we settled on this washer. It has served us well for the past 6 years. At the moment, however, it is out of commission. The bearings wore out. My husband ordered new parts and we hope to have our washer up and running again in a couple of days.

Bought a MDB7601AWW, and then replaced front panel to stainless. Configuration options are great (can’t find better at cost up to $1,200.00)! I haven’t had an issue with any stains on non-stainless tub. Problem is now control panel failing for second time. After 1st time, sealed all connections in silicone to prevent steam from affecting it, as recommended on DIY video. I just replaced the door latch, thinking that may solve it, but hard to troubleshoot without any indicator lights. This second failure (2 yrs later) shows no indication that steam or water caused it. It does start now, stuck on heavy wash, heated dry, sanitize - per top lights. Front lights totally out. Debating whether to buy a new dishwasher ($$$) and give up super config (hard to find fold-down tines and fold-down small shelves on upper and lower racks, clips for small items, and basket that can be changed, placed anywhere) or spend at least $162 for the panel AGAIN and hope I get another 2 years from that while trusting that some other element doesn’t go out. I believe Maytag should, at minimum, make the panel reasonably priced by offering a rebate, since the part is not sold directly through them. Obviously this problem is a design flaw. I am the only one in the house, so the dishwasher is not under heavy use. At least I found how to replace it myself on YouTube, though it requires the door to be completely taken apart and would be easier with an extra set of hands and a younger back. Hard decision since it seems newer, expensive appliances have problems as well. If I buy new, I will not hesitate to get an extended warranty (1st time ever).

I purchased the Maytag Bravos washer and dryer set one year ago, and have asked myself why ever since. The oversized laundry tub is what attracted me to the model, but it sure doesnt deliver for the money it cost. On normal settings, it doesnt use enough water for all the clothes to even get wet. After the load was complete, there were areas of my clothes bone dry, and obviously still dirty. I soon learned that the only way the washer uses enough water to get all the clothes wet and clean, was to set the machine on the bulky setting. This is the only setting I use now, but all of my clothes winds up twisted together, sometimes in one big ball. As for efficiency, that statement folks is a joke! Because I use the bulky setting, it uses much more water than a traditional washer ever did, and when the load is off balanced, it will go through another rinse cycle to try to even it out. This machine uses far more water and electricity than my old school set! I suppose if you dont get your clothes dirty, you may not need to use the bulky setting, but thats the only way I can wash my laundry with this machine. The old style set I had before this was Maytag also, and lasted about 20 years. I was more than happy to purchase Maytag again, but this set has been nothing but a disappointment. I dont plan to buy another energy efficient machine again, nor would I recommend this product to anyone!

Have had this problem since week 2 of ownership. Even on the lowest setting, food in the fridge section is freezing and Im having to throw out fresh produce weekly. Called Whirlpool service since under warranty. The very nice service man replaced the thermostat. Only a little bit better as the temps do not range quite as extreme - only 25-46 now! I am now waiting once more for a service appointment, at least 10 days. Plus in Massachusetts they will only give you a 8-5 service window. They give a robocall the night before and you are given a 8-12 or a 1-4 time for your appointment. I also have had trouble with the meat drawer falling out of the track because the upper shelf bows with the weight of a normal amount of stuff. Now the bracket has cracked and the meat drawer no longer stays on the track when it pulled out partially (such as when you need to reach in and get something). Same thing happens with the lower drawer on the right side although the bracket hasnt cracked.

Bravo XL washer and dryer - I had the washer approx 2 months before it leaked water all over the laundry room. The company replaced the washer after two weeks. Now the dryer has gone out after two years. If it cost me the amount stated by other consumers I wont be fixing it.

In 2007, we bought a Maytag Neptune Washer Dryer Combo from Lowes. By 2008, the washer started stopping operation at every rinse setting, requiring someone to constantly monitor the machine to assure that the button was pushed to fulfill the entire cycle. We called a repair company and were told that the machine was shutting down because the screen in the water intake was getting clogged with debris and was making the machine feel that the water was shutting off. Thus, according to the repair man, the machine was shutting itself off. He showed me how to clean the screens in the intake line and charged me about $150 for the service call. Within a week the machine was doing the same thing again. I pulled out the screens and they were clean. We continued to watch over the washer whenever it was doing the wash and continued to push the button to restart the machine. We live in a very rural area and there are really no repair services available without paying enormous fees just to get them to make a call and the wait is often more than a week.Shortly after the intake incomplete cycle problem, the washing machine stopped getting the water out of the clothes in the spin cycle, forcing us to wring out the clothes before putting them in the dryer. Then we noticed that the washer was leaking from the bottom rear all over our hardwood flooring. We went out and bought a new washer dryer based on reading consumer reports.The cost to replace this piece of crap from Maytag was in excess of $1600. We are only in this house part of the year so this Maytag product not only did not work very well over the short time that we owned it, but it was only being used for a few months out of the year. We have since learned that there was a class action suit over this product line and would like to know how to join the suit. We are so far out in the woods that we will not get our new washer / dryer until some 2 weeks out from our purchase. We have spent nearly $3,000 since 2008 on washer dryers, an average of $1,000 a year.

We (husband and wife only - no kids) had our Maytag washer for 4.5 years and around year 3, the control panel would need to be reset by unplugging it and plugging it back in. That alone was an inconvenience. This time, the Control Loc light is lit and will not go out despite using all troubleshooting suggestions listed in the guide so the washer is not usable. 10 year warranty covers the drum. I say that is like getting a warranty on tires and when one goes flat, you are told it only covers the hubcap. I can only rate the unit as garbage. Model is 5500, front load. So much for Made in the USA.

So wife and I purchased a Maytag dishwasher in late 2012. A year and a month later it turns into Hal 9000 from 2001 Space Odyssey. I press normal, it shows light rinse. I press heated dry, it tries turning off the life support and blowing me out the air lock. Finally, in March it dies. No power, no nothing. $500+ for an appliance that lasts 2 years. So for the past few months, while we wavered over buying a new brand or spending $250+ on a repair, we were washing dishes by hand. It was as bad as my grandma used to say it was. Then, by chance I ran across a web blog talking about this being a common problem, and there are hundreds of complaints, and its a problem with a $4.00 part on the control panel that can be fixed with a Q-tip, rubbing alcohol, and silicone... Im not a handyman by any stretch of the imagination, but even this I could do. Unplug or switch off the breaker. After unscrewing all the screws, (not your standard or Phillips head either) unplug the control panel from the control box and remove the control panel. On the back, youll notice a flat cable (pictured below) that will have dark marks on the opposite side of the part sticker. Gently clean this with a Q-tip and rubbing alcohol. I then covered the back (side without sticker) with silicone, (you can get at hardware store or Target) let dry, and put everything back together again and now its working better than new. Im regarded as a master handyman in my house, and I didnt even have to hear the dishwasher sing Daisy Bell as I disconnected it. With such a simple fix, Im amazed Maytag didnt just own up to it and get it addressed. The millions it will end up costing them in the long run, by this frustrating experience shared by us all will have them thinking twice in the future (hopefully). It is a shame they seem to be adopting the business model of American auto manufacturers of the late 80s. Ill update this in a year and a month to let you know how the fix worked, and you owe me a beer for saving you $150 - $600 for a repair or replacement. One word... VICTORIOUS!!

My freezer has been leaking from the bottom for a few months and now the icemaker has quit working as well. The refrigerator has been purchased less than two years ago. The warranty is expired. I will not fix this refrigerator, as it is a gigantic piece of junk. However I would like to be compensated by Maytag at least 1/3 of the price so I can have it removed from my house before it creates more damage to my floors and subfloors.

I have a new HE (high efficiency) washer. It takes getting used to as its a definite change from the old agitating system but I think I like it. It doesnt make much in the way of suds but everything still comes out really clean. The wash cycle is much longer than my old washer but it uses a lot less water.

Just got off the phone with Whirlpool Customer Care after getting the run around between parts and customer service for most of the morning. My issue is with the shelving on my MSF25D2EAS01 Maytag side-by-side refrigerator. The plastic surrounding the glass shelving is disintegrating and they are not admitting to a defective design only that the original part has been obsoleted and a new one is available for purchase (an over $300 expense to replace three shelves) on a unit that is just over 2 years old. I am willing to bet the old part has been replaced with a different design after they realized a substantial number of customer complaints. As an engineer, it is obvious to me that these shelves are poorly designed for their intended purpose, furthermore my work allows me to recommend appliance brands for large projects so I see no reason to recommend Whirlpool or any of its subsidiary brands (Kitchen Aid, Maytag, Amana, Jenn-Air) to any of our clients. Whirlpool quality and customer service is substandard and no better than any imported brand of appliances.

I have a 6-month-old top load Bravo Washer. It has destroyed two bottom fitted king size sheets and 2 shirts that now have holes. It apparently slices the sheets during agitation. I have a service policy and called the service agency. The technician said there was nothing wrong with the machine, yet it literally ate 2 more items. Help! I need a solution to this problem.

I purchased a Maytag side-by-side, model MSD2656DEQ, in June 2000. First service call within a couple of months was for a very noisy ice dispenser, which the tech said was normal. Other than the noise, the dispenser has worked fine. Aug. 2005, the freezer frosted up and the tech replaced the defrost timer and defrost thermostat. May 2010, I had the same problem again and again these two parts were replaced. This morning, I found the food thawing in the freezer, 3 1/2 yrs since last repair. It is Sunday so will have to call tech tomorrow. Third repair in 13 years for a $1500 (2000 year dollars) Maytag. I have never had an appliance with so many problems and it was the most money I ever spent on an appliance. I am done buying Maytag products.