I give the product lowest and poor rating. The bearing in our washer went bad 4 months after we bought it. For the fourth time, they are coming out to repair the washer on 01/11/2012.

Like many people here, I have a Maytag Dishwasher Model # MDB7749SBW3 Serial # F40107007. We have had this dishwasher for about 12 months to 18 months. The first indication that there was a problem was some of the lights were acting strange. Then the dishwasher starting going nuts. I removed power from the unit thinking that maybe the controller became confused. The problem persisted. I would hit buttons and either nothing would happen or something completely different would happen.I take the dishwasher door apart and remove the touch pad. I notice some discoloration on the ribbon cable. I remove the glued on front panel to look at the electronics behind it (see pictures) and I see some discoloration there as well. So using my multimeter, I find that there is a direct short between pins 4 and 5. I vigorously flex the cable at the point of discoloration and the short goes away. So at this point, I doubt that I can get just the flexible circuit strip so Im going to have to pop for a new touch pad assembly. I didnt go further in the measurements as there was no point since I already detected one failure. Furthermore, I inspected the computer control unit and I did not see any obvious signs of corrosion or discoloration anywhere on the processor board. So it appears that there is no problem with it.Conclusion: Many people are at a disadvantage when it comes to electronic devices. In my professional opinion, this is clearly a failure of the insulating material of the ribbon cable due to environmental contamination. Visual inspection shows that corrosion of the conductors is clearly evident. About Me: I have been an electronics technician on and off for over 20 years now. I have a 2-year college degree in electronics technology and I am currently in school to become an electrical engineer. In my house, when something breaks, I fix it.

I purchased a Maytag range with self-clean oven. Manual says to put 2 cups of water to self-clean and no cleaning is done. I called Maytag and they said it is environmentally friendly and the rest of baking stains I have to scrub myself. This is totally unacceptable. I also cannot clean with easy off, it will damage the inside of the oven according to Maytag customer service. I do a lot of baking. What am I supposed to do now, live and cook with a dirty oven! Ugh!

Maytag never fails to please me. My dishwasher is so quiet I sometimes have to put my ear next to it to make sure it’s actually working. The inside is stainless steel (those are the quietest) and it has a child lock so my 2 yo grandson can push all the buttons he wants and he still can’t mess things up. I love the high temp and sanitize features and everything is always clean and dry when done. It seems like it takes a long time to run through all the cycles, though. That and no adjustable top rack are the only two things I miss with my previous dishwasher.

We are in the process of replacing the 2nd control board in the past 2 years (have has this dishwasher for 3 yrs) on our Maytag dishwasher model MD87749AWW1. The lights on the panel completely quit working mid cycle. At $175 per replacement, we are into repairs for half of what we paid for the dishwasher. Bought Maytag because it is made in the USA but found out that a majority of the parts are imported from China? Very disappointing.

I purchased the subject Maytag washer (MHWE201YW-3.5 CU FT WHT FRNT LD WSHR) from Home Depot in December of 2012. I got exactly 1 year of use and then the washer stopped working. I called the Home Depot repair person who came and repaired the unit. The repair lasted two weeks and the washer stopped working again. Because the unit was no longer under its 1-yr warranty the Home Depot repair person was not available for repair. Another independent Maytag repair person came and evaluated to problem. He said the computer which is located on the motor was no good and to the tune of over $400.00 (parts and labor) a new motor was purchased and installed. It lasted two months and it quit working again. After several months I was finally able to contact the original Home Depot repair person for one visit. He said he would check the code message and get back to me. I never heard from him again. I have been taking my laundry to the laundromat ever since and it is getting expensive. I dont want to spend another $400 on this machine as it will only break again. What do you recommend?

I am 65 years old and for all of my life there has always been a Maytag washer and Dryer in our home. My great grandmother and great grandfather had a gasoline powered Maytag. My maternal grandmother had wringer-Maytag and my parents have always purchased Maytags. When I was on my own I purchased Maytags. In November of 2012 I purchased a Maytag Bravos XL washer and dryer. I had no reservations because it was Maytag. In October of this year (2017), the washer starting roaring and I had purchased an extended warranty. I called a reported this. A local appliance repair provider was sent out after I called the 800 number on the warranty agreement. I waited several days and finally called the repair provider and was told the parts needed were backordered. Time rocked on several weeks with no communication until I began calling both repair provider and warranty company. Still no washer repair. Ultimately, the resolution was not to repair or replace the washer, but to refund the purchase price and sales tax. The Home Depot salesman that sold us the washer and dryer, as well as the extended warranty coverage assured us that should either the washer or dryer fail it would be repaired or replaced, neither occurred. This left me without a washer for more than a month. Then finally I called the warranty company used by Home Depot and I was told a refund check would be sent for the washer, along with laundry reimbursement check. My difficulty with this is even though I got my money back on the washer and some of my expense on having the laundry and dry cleaning done elsewhere, it does address the issue. Simply, I see the Maytag commercials all the time and they are simply noise on TV now. I am still wondering how this could happen to a washing machine that had less than two and half years of use, never abused, cared for could fail in five years. I was used to having Maytags last decades with little or no repairs. Given the fact this machine was top of the line and well taken care of, I so very disappointed and not buy another Maytag of any kind again. By the way, I have a home in the country with a 27 year Maytag washer and 20 year old Maytag dryer that come from my home in town that Bravos XL dryer replaced. My research during all of this has led me to conclude this is not an isolated incident, but far larger problem with these washing machines. Why has there not been a recall on these inherently defective washers been issued. Where is the justice in this, even though the refund and small laundry reimbursement has been received it does not make any happier. I have lost my confidence in Maytag and I thought that could not happen with Maytag.

I bought my Maytag dishwasher in February 2011. It seemed like a good model - basic functions, upper spray arm, stainless interior. Well this dishwasher has been all downhill since I got it. First it is cheaply made. The racks and plastic stoppers on the racks immediately started falling apart. The one year after we installed it the front control panel went out, rendering the dishwasher completely useless! The warranty had just run out! To my pleasant surprise, I received an extended warranty offer from Sears. Had the front panel replaced and it started working again.... but apparently it is a bad design and it is likely to happen again. After reading online I am not the only one with this problem.Now another year later we are having a the sprayer on the top and the back hose replaced..... (still waiting for sears to install). It makes grinding sounds, leaves white marks, doesnt clean.... it is a non-stop battle with this product. Upon calling Maytag, they said they could give me advice but cant pay for any parts or even give me a coupon towards a new product! I have tried everything with this dishwasher - fancy soap, cleaning solutions, jet dry... its not me, its Maytag! I will likely be in the market to buy another dishwasher next year because of all the issues, and it for sure will not be a Maytag.

In August of 2009, we had an opportunity to remodel our kitchen plus add new windows and doors. How exciting! SO we had put down new flooring in our kitchen that matched our oak cabinets and since we had a little money saved, we wanted to purchase new appliances to match. We purchased a Maytag side by side with ice and water in the door. It also had the fingerprint resistant stuff on the outside. It cost about $1300. You buy name brand so they will last a while but here we are November 12, 2014, 7 years later and the compressor goes out. If repaired, it will cost $8090 to fix. Why do I want another Maytag. I got a citation I bought in 1978 and it still runs. Hello Facebook, you will my next visitor.

I purchased this washer because it has a large, stainless steel drum, and a deep wash setting. My laundry comes out very clean, and I do not need to run it through an extra rinse cycle. The sensor determines what size load I put in, so I am not wasting water on small loads. Overall, I am very happy with my washer. I purchased it about six months ago.

I bought a fridge, model number MBF1958, its a top fridge-bottom freezer. The freezer part leaked and spilled water that then froze onto the bottom of the freezer, which of course froze. I discovered this 1 month after the 1 year warranty ended. Maytag gave me a courtesy repair service guaranteed for 90 days. Of course, 2 weeks after the 90-day period ended, I have the same problem again.

Brand new washing machine model MHW8200FW purchased at Karls, a Ferguson subsidiary, in Madison, NJ end of June, 2017. I wanted to buy a top of the line machine and this is what the sales person recommended to me. Problems started soon after purchase. Initially I contacted Maytag because the machine wouldnt spin dry a cotton bath mat weighing 4.5lbs soaking wet. I was told I should put more items in the machine to help balance it. Well there WERE more items and the machine wouldnt spin dry them either. I tried every trouble shooting Maytag suggested. Having exhausted my nerves, I called for service. The technician came and said these machines are extremely sensitive and that sometimes they wont even run an empty cycle. He said this is a common complaint with these units. One of his suggestions was to take bath mats, duvets, comforters... articles like that to a laundromat.I did less than 10 wash cycles after his visit when the washer started having more issues and finally broke down completely. The technician who came this time wrote a repair order indicating a mechanical (Stator) AND electrical (Control Panel) breakdown ($500+ for the parts alone if the unit wasnt under warranty). He also stated that he had never seen such problems in a brand new machine.I contacted Maytag for an exchange. Maytag customer service wrote to me that the breakdowns are ... normal, with all the units we sell some may have a defect in the first couple of months... and refused to exchange my defective unit. I can accept that there may be a defect that will warrant a repair, but in this case there are multiple defects in separate systems - mechanical and electrical - within the first month of service. This shouldnt warrant any further discussion, only a quick replacement and an apology.

I bought a Maytag MEDB835DW0 s/n M51202974 just about 2 months ago brand new. After less than 2 months it malfunctioned that it would not start. I called the customer service center on Sept 11, 2015 to report my problem. The rep I got was polite and caring and said she would keep on top of this. On Monday I called the customer service again to get an update. They could not locate one of the authorized repair people. The one they found did call me back but I was out of their service area and would not service my dryer. I was told that my problem was turned over to their Maytag/Whirlpool research or resource to find a repair and I would be advised within 7 days. They did give me options, I could take my clothes to a laundromat, which is 17 miles away where I love and they wont pay for my gas. Or I could get my own repair center but they would only cover up to $150 of the repair in labor cost and the part would have to come from Maytag/Whirlpool center. Then I would have to send my invoice to Maytag/Whirlpool for reimbursement. Now a company that cant get me a company to fix my dryer is going to send me my money back to me in a timely manner? I dont think so... Now on Monday after talking to the customer service I got a request to fill out a survey of my experience. I filled it in with details and today they called me from the corporate off in Benton Harbor regarding my survey. Well I finally thought I would have some action on this... Oh no was I wrong, they wanted to know why I filled it that way. I told them that this is a warranty issue. They did not offer me anything new but the same crap that the customer service offered. I now have a dryer less than 2 months old that I paid cash for. I am also 70 years old and on a fixed income as I explained to the Benton Harbor. It is quite evident that they could care less about customer service and their warranty. They do advertise on TV the Maytag repairman. Trust me this person does not exist and now I have $700+ item that I should put out on my lawn, take off the door and use it as a planter... and have a sign on THIS IS MAYTAG. DO NOT PURCHASE ANYTHING FROM THEM. I am so frustrated with this issue I want to scream.

I wish I had researched high efficiency washers before buying because of a name we trusted implicitly. Our washer does not get our clothes clean & cleaning it with Affresh is not enough. I have never had to work so hard at getting clothes clean! Towels smell musty, stinky. My husbands sweaty workout & gardening clothes smell worse, even with subsequent washes & his shirts have white spots from the detergent not even being washed out. The rinse cycle water just washes out the bottom of the machine while the clothes are plastered against the side of the machine. I do not wash my husbands clothes with anyone elses or it all smells and if he washes them twice, they still have that odor that comes from being dank. Even if I stop the washer to arrange the clothes on the bottom so they will get rinsed properly (gotta wait two hours for a load to finish) I have bought every HE laundry detergent on the market, every odor remover, vinegar, baking soda, bleach. For a year Ive been chasing my tail to do the dance that I never had to do with a top loader agitator Maytag that we had for 7 years and never had to clean once, but used unscented detergent that got the worst smells and stains out without much thought. Even reviews that I read about their amended top loader with an agitator are not very good.

Ten years ago I bought a very expensive set of Maytag Neptune Washer MAH5500BWW and dryer units with the single all-in-one pedestal. The washer starts sounding like a freight train during the fast spin dry cycle. A service tech came out, turned it on, listened, told me it is bad outer tub bearings going bad. And the price to fix is $846. Its essentially a throw-it-away deal. The tech says he has done hundreds of these and its a 3-hour major tear down, the bearings are press fitted and you essentially buy a new outer tub instead of replacing the bearings in the old one. Maytag went out of business and was bought by Whirlpool. What a piece of crap and to think how great Maytag once was. Now I have a dryer and a pedestal that probably wont fit any other washer brand.

I bought the Maytag Bravos XL HE washing machine because I needed a machine that could handle large loads to save me time doing multiple loads for everyday items like jeans to towels, blankets as well as delicates. This machine is a COMPLETE disappointment. It does NOT get anything clean unless I wash it 4 times with bleach and pre-stain 4 times. You know what bleach does to your clothes! The water level is so low I can only wash 4 things at a time and I still have to wash additional times. It doesnt get the smell or food stains out. Not a good choice for an active family or person. Ive had clothes come out with suds still on them after washing three times. I use less than the recommended amount of HE detergent. There was a $250 agitator washer by GE at Lowes but it was smaller - how I wish I bought it. These impeller HE machines dont work. My advice steer clear of this Maytag product unless you like to waste your time re-doing loads of laundry.

We bought a heavy duty washer 1 year ago and paid a decent amount of money for it. Had it delivered and installed mid February of 2020. Worked fine until Dec when the lid cracked (which is common said the Maytag repair man), but since it wouldnt lock, we couldnt use the washer. 1 week we were told and it would be in - a month later and over a hundred dollars spent at the laundromat, the part came in. Used the washer for 1 round of laundry - 3 days later all these error codes started and our washer wouldnt work again. 2 weeks this time for the parts and another $100 at the laundromat- a month today and Im told they are on backorder.Called the place we bought it and they said to call Maytag. Call Maytag and they said that they will try to expedite the parts and could offer me a whole $75 for the inconvenience. They will not replace the washer or give me a loaner until the parts are in. 2 months w/o a washer on a 1 person income for a family of 4 and they cant do a single thing to help. If a 10 month old washer needs 3 new parts one of them being a new control panel - within the first year - this is a lemon and should be replaced. I was told they are big on customer service, but obviously Im just a little fish in the ocean and they dont care about me.

MFF2558VEM0 - Had the same problem repaired less than years ago.. Now has the same problem. Looking for a new fridge. Hope better luck this time.

Purchased a Maytag Dishwasher (Serial # P33706417) in Sep. 2013. In the beginning was working fine. After a year and a half started having problems pushing the button to start, not starting. Had to wait a few hours then hit it again and all the lights would light up and then it would start washing. Then when done, some lights stayed on and never went off. Then a month or 2 later, same problem but only a couple of lights would go on and when done 2 lights would blink continuously. After several months now, none of the lights are working and cant get dishwasher to start. Called a tech and he said the control board and the touchpad were not working. Would cost me over $400 plus shipping, etc. to for new. Very frustrated with Maytag, as we havent even gotten 2 years out of this dishwasher and the 1 year warranty has expired. DONT BUY A MAYTAG!!!

My dishwasher was bought December 2013. The control panel just started going crazy and cant control anything. Unless you have bought extended warranty Maytag isnt doing anything. This is obviously a manufacture defect and no one is doing anything about it. Will no longer buy Maytag products if they cant stand behind their product.

I bought the Maytag Bravo XL washer and dryer at Lowe’s on sale spending almost $2000. Loved both of them until the washer stopped with a load of laundry in it. No power to unit. Called for service. Could not provide serial number as locked in washer. Service company able to order parts without the serial number but part put on back order. Washer needs a master board. After 1 week of wet laundry stuck in the washer called store manager at Lowe’s. I contacted Maytag Service and had a rude customer service clerk who finally listened to me after I got angry with her. She contacted the appliance repair company and got the back ordered part sent to the appliance repair company. We are now 10 days out. Still do not have the part; just talked to appliance repair company supervisor. The appliance repair company supervisor said he would schedule installation as soon as he had the part. It will probably be 14 days when I get the washer fixed. I am dreading opening the washer to get the load out that I will have to throw away. When I called for service at Lowe’s the representative said, We have had a lot of issues with this. A 2 month old new washer should not have the control board go out. Shame on Maytag.

Product number MMV4205DS. Beautiful, felt solid. Right away when we would put in a time to cook and hit start, the thing would say Open Close Door. First we thought it was moisture, and we would wipe the seal, then lifting the door a little helped. A month might go by and we would repeat this process. I did a little research and found the microwave is known for this. After the warranty was up, it got worse. My husband put a little screwdriver in the door clamp. The plastic guard that held the door shut fell behind the opening. Mulling over whether to call for repairs or buy a new one, we decided the latter. I am buying another one just like it, because the holes in the wall will match for an easy swap and it matches my suite. This time I took out the 3 year warranty, which I will hold Maytag responsible for any more problems. They say if they come and fix it 4 times in a year they will declare it a lemon and replace. I figure this will work in my favor because the microwave lasts a year!

I would like to say that I purchased the Neptune washer & dryer for my parents back in 1998. Up to now, 23 May 2015, not once has either of the machines required service and have been functioning well for the past 17 years. This is a testament to the quality and workmanship that is Maytag. This week I have purchased the Maytag Maxima front loading washer & dryer for my home because of Maytags reputation.

We purchased a Model MDB8949SAWO Maytag dishwasher in September 2012. The control panel failed in November 2015. We wrote a letter to Maytag (Whirlpool) expressing our disappointment and received a call from Maytag customer service. The Customer Service representative informed us because we contacted our local repair facility directly, no reimbursements would be provided. During a subsequent follow-up call, I was informed by the Customer Service representative that Maytag manufactures quality products and that no premature failures were occurring with Maytag dishwashers. The Customer Service Representative stated that we should have purchased an extended warranty which lends some support to the fact that Maytag dishwashers are essentially junk. Never again will we purchase any Whirlpool products.

If there was a zero star rating available, that is what I would select! We purchased this range along with a complete kitchen ensemble for a remodel of our kitchen in December of 2011. Within a few months of purchase the enamel finish started blistering, flaking and peeling. Upon contacting Whirlpool Corp about the problem through their online chatline, email, regular mail and phone, we were informed (quite rudely I might add) that Whirlpool does not warranty cosmetic deficiencies over 30 days after product purchase. This is American Quality?? Since this has occurred the retirement home we are building will have no Whirlpool Corp products in it which includes: Maytag, Whirlpool, KitchenAid, Amana, Jenn-Air, Brastemp, Consul, Bauknecht, Gladiator, or any of the product lineup from the Chinese company Hefei Sanyo which they are buying. The attached photos were taken in May of 2012 and since that time the product finish has only exponentially deteriorated.

Had some extra time, so I thought Id add my .02 to those including myself disgusted with Maytag products! 1st up, the Maytag washer and dryer I purchased from my nephew after his divorce. The washer shot craps 2 months after I bought it from him (out of warranty of course!). The transmission went out - cost to repair $550.00. My nephew paid $350.00 new at Sears. We happened to have our ol reliable clanking GE, so we used that while deciding what to do about the washer. In the meantime, the dryer quit heating. Cost to replace heating element - 400 smackers! Dryer new at Sears was $250.00.Come to find out that even though they had Maytag names on the washer/dryer, they were cheap copies by White/Westinghouse. Well anyway we bought a set of Whirlpool Duets before doing our homework, cuz if we knew what was gonna happen... Before we knew the trouble we were going to have with the washer/dryer, we got a Maytag Quiet Series 300 dishwasher (Maytag Quiet Series 300 MDBTT60AWW). Yip, the control panel failing problem! Only purchased 1 so far (only 1?!), but my wife likes to hand wash the dishes. If we were the typical family using the dishwasher all the time, I would have replaced more than 1 at a cost of $135.00 each from Sears and doing my own R&R work, saving on the labor. Cost new at Lowes - $350.00Up next is the Maytag fridge. I purchased it back when our 2 boys were at home. I bought it mainly for the name and large capacity. After about a year (yip out of warranty) the cooling was very uneven. Sometimes the freezer would defrost by itself, then it would start working ok again. The top couple of racks in the fridge would be quite a bit warmer than the bottom. I understood the top racks would be a little warmer, but Im talking like 15 degrees. I called a repairman and told him about the problem. He said hes received numerous complaints on this particular fridge, and theres really no way to repair it unless the electronics are replaced as well as the compressor because as the compressor gets weak over time, the electronics get fouled up by this. Cost new - $1300.00. Estimate over the phone cost to repair - $950.00 with no guarantees. Replaced with a SamsungAs far as the Duets? No problems so far. They work great and we are very pleased by them. But I have did my research and am holding my breath! I also have a Maytag microwave thats still working, but has did a couple of unusual things - the lights in the front panel display started flashing showing a fault. I unplugged it when its did this to reset it. That was a while back and now it seems ok. At least for now!When someone says, Yeah, well, you might just have a lemon, but the rest of Maytags appliances are fantastic! My wife and I when we hear this are ready for a fight! Weve had experience with all of Maytags products, and with the exception of the Duets (so far), they are nothing but junk!! Another thing I wish to mention is the Samsung fridge. Its about the only model that has a factory 5-year warranty on the compressor and major components. Weve had several fridges in our married life, and the Samsung is far superior to any fridge weve owned. Ill be looking to that brand in the future. The last item I promise: If you read the reviews on front load washers, none of them get very good ratings. If I would have know that, I may have purchased a top load. But the Duet washer does do a superior job (IMO) cleaning the clothes, and the clothes are virtually dry after the last spin.

Dishwasher Model MDB7749SBM1 - When I returned home from work today, I noticed the cancel drain button was on and the unit was continuing to try and drain but the dishes were not clean and the cascade pod was still inside the unit unused. I then proceeded to run another cycle to clean the dishes and what happened next simply amazed me. I pressed the jet clean button, tough scrub and 2 hour delay button and thought I was all set but the start/resume button would not engage or light up at all and subsequently the cancel/drain button lit up and the unit started draining. Now the control lock and start/resume button just flashes intermittently and wont disengage. I purchased my unit along with several other new Maytag appliances when I renovated my kitchen. I guess the microwave, stove and refrigerator is next -- unit are only 29 months old. Any assistance will be greatly appreciated. Im in deep ish I guess.

The machine will not fill with enough water to wet all the clothes. I have to tape the tub to trick the machine so that the clothes will all get wet. When I had a service look at the machine he said that is how they are designed to be energy efficient. Who does not getting all the clothes wet clean them??? This is not for big loads but ALL loads - even hand wash loads. Every load takes an hour plus. Less water, more time, unclean clothes. I lose all the way around. REALLY wish I had a machine with the old features.

I purchased this washer from Lowe’s on 8/9/2017. After 3 years and 2 months, this washer would no longer power up. I tried resetting it by unplugging it and lifting lid 6 times. It didn’t work. The extended warranty from Lowe’s expired on 8/9/20. I called a technician and he found it need a control panel and control board. He suggested that I call Maytag to see if they would give me the parts as a courtesy since the washer was only three years old. I contacted them and experienced long wait times (51 minutes was the longest). I spent a total of 3 hours on the phone with them. They said no there was nothing they could do for me since the manufacturers warranty ended 2 years ago and the “mother control panel” doesn’t fall under 10-year motor warranty. Well, there’s no need for a motor warranty if there’s no power to the unit! The cost of the parts would be almost $600. It is shameful to not stand behind your product. I would expect to have to replace an iron or a juicer after 3 years, but not a washer. This was a major blow to how I would view the way they do business. I purchased the extended warranty from Lowe’s. I will never do that again. It was a waste of money. They didn’t make any concessions for me either. They kept saying it was a manufacturers issue.

We bought our Maytag Bravo top loader on May 5, 2010. The machine was working fine. Then last week with no warning, the F51 error code popped up. We called Sears and they sent a repairman out. The result was the sensors work independently from each other (tested correct in the Ohms range). It made it through an entire diagnostic test, but will not complete a wash cycle. The repair guy concluded that the control board was bad. Estimated cost to fix was upwards of $400. I cannot afford to fix. Our issue with this product is that it is apparent, from reading all the forums, that this is a known issue. And we believe Maytag should be reimbursing consumers for this repair or they should recall the washer. Our washer is used on the weekends and it should have lasted us for minimally five years. All we wanted was to make it through one military overseas tour with it, not asking much. Instead, this machine lasted two years. Unacceptable.

My new dishwasher had a defective board and worked erratically. Shortly after the warranty was up it stopped working completely. I contact both Maytag service and Home Depot on several occasions with no satisfaction. This a well known defect. Apparently the board replacement and service would cost in the range of $250-300. Too much for me as a senior on fixed income to justify. No dishwasher for almost a year. I then read an article indicating there was a class action settlement in California on the same make and model. I called Maytag again and after spending 2.5 hours on the phone I finally reach a person who sent out a service repair person. This person showed me a memo confirming the problem with the board. No recall but... if a customer is persistent they will give you the board. Finally new board installed at no charge.

I dont know anything about the Maytag washers and dryers but have a Maytag washer and dryer. And I just recently bought a house that the owner is leaving both the washer/dryer, and both are Neptunes. I have an older set of Maytag washer/dryer and they are about 20 yrs old. They are both top load and I had one repair where a water line had a small leak and the service man came and fixed it and havent had any problems since. So I came on Maytags site to see how good these are, but from what I read, I think I will give the set of Neptunes away and just keep my old set as I am told them will last a good 35 or more years. They are heavy duty and large capacity. Thank you for letting me comment on your washers and dryers.

Not long after dishwasher MDB7609AWB2 was out of warranty the START switch on the keyboard would not work. Called dealer and they sent someone out to check for a charge not quite $100. Could not fix it so said it needed a new control panel which with labor was almost $200. Doesnt work so get it fixed. Now less than 3 years later the same thing has happened - wont start. Lousy engineering and part probably made in China to save Maytag money, I feel is the cause. This is happening over and over to those of us who purchased in good faith what used to be a reliable product from a reliable company.

I purchased the Bravos washer and dryer suite. Since I was a small child I had heard my parents and others alike say that Maytag always had superior products as this is the reason when I was fortunate enough to purchase a new set I chose a Maytag brand. We that was the past and the present products et washers /dryers as the worst ever. I have had my set less than 2 years and today had to go out and buy a used one again. I have had nothing but trouble with these 2 and will never buy their brand of anything again. From the amount of poor reviews it appears I am not alone. I tried several times to no avail to have someone from the company contact me as I was put on hold too many times!

I have purchased my top loader Bravos washing machine 3 1/2 years ago and I have had nothing but troubles with my machine. I have had to replace the motherboard twice and I constantly have that foul smell in all our clothes. I have to wash each load twice and still the smell doesnt come out. I have also complained numerous times about the water level not being correct, but they keep saying that is how the high efficiency machine is. I can watch my load washing because we have the clear lid which I like. But at the same time, it gets me really angry seeing how this doesnt clean clothes like it should. I dont believe that the water levels are right at all. I have clothes that dont even get turned over as they are washing and I have even smaller loads than before. I can only clean 4 adult pairs of jeans at one time and I still think that is too much. I clean my machine every time the red light turns on with the Affresh tablets and sometimes I run a clean cycle with just bleach. Maytag has done nothing to try and correct these problems. Its so sad that I have to take my clothes to the laundry mat to go wash them and there I have absolutely no problems. They have the HE front loaders and they have enough water to wash my clothes and I can actually see them being washed. I will never buy a Maytag washer or dryer again. How sad you have all these complaints and no one to help you fix or correct them the right way.

Maytag range model mer8875ws - Glass top broke on brand new oven over most used burner then glass spider lined out from there. Wife called Maytag and they told her that it broke from the impact of something dropping on it. I guess the man was psychic because he had no picture of SO CALLED IMPACT SITE. Now they wont replace or fix range, ** Maytag. Paid 699 for range they want to charge me 900 to fix. MMOOORROOONNSS! Like ** thats how big business treats everyone now. Thats how big business treats people these days.

Terrible! First and last frontload washer I will ever have. Seems like every other load will not spin clothes dry no matter how many times you rebalance. You have to add more clothes or take some out dripping wet to finish the cycle. Most annoying appliance I have ever owned.

I had a brand new Maytag refrigerator freezer delivered to my home. Not three days later, the freezer compartment is frosting over on the back wall, while the refrigerator fails to keep my drinks cooler cold like I demand. Ive heard of planned obsolescence, but this is ridiculous!

I purchased a Maytag Centennial washer and dryer on February 4th. It was delivered on the 11th. I am dissatisfied with the performance of the washer. I use the same amount of detergent and fabric softener as I did for my 15-year old Maytag washer, but the wash is not as soft as with the old machine. Also, the wash when finished appears to be a lot wetter. What is wrong? What else can I do?

It meets all of my needs and expectations. Its quiet looks nice and does a very good job of cleaning dishes.

The washing machine is great as long as you’re washing small loads. If you try to wash a large load or heavily soiled items it does not get them fully clean. I have had absolutely no problems with the dryer except that I have had to replace the handle on the door which was a very inexpensive repair.

We purchased all Maytag home appliances when our home was remodeled about five years ago. After the first year, the microwave had to be replaced because it malfunctioned. The dishwasher stopped working in the third year, and now, my refrigerator (model# mf12568AEB) wont cool. The technician told me that all of the Freon had leaked out because of a design flaw. Moisture had gotten into the compressor, and with the cost of repair or replacing the compressor, I would probably be better off buying a new refrigerator, preferably not a Maytag.

I bought the Maytag Bravos X washer and dryer combo 4 months ago and its been a hassle every time I use the washer. The dryer is fine, but the washer constantly has problems. No error codes, I just hit start and it clicks intermittently in sensing mode for 10 minutes and shuts off. Once in a while, it decides to work - adding water, but never cleaning thoroughly and I always have to run an extra spin cycle because the clothes are sopping wet once it finishes. Ive been reading reviews all over the internet describing similar issues with these models and I am kicking myself for allowing myself to be convinced Maytag is a quality brand. Dont waste your money on these pieces of junk and really do your homework. I wish I had never bought them and am angry that I will have to deal with it until it eventually breaks down in the very near future, Im sure.

We purchased a Maytag dishwasher at Home Depot in White Bear, MN in November of 2011. The dishwasher just quit running last week and the repair person told us the control board needs replacement. We will have the control panel replaced but have determined this machine is of very poor quality and will never buy a Maytag appliance again.

While washing clothes in my Maytag front load washer, I noticed that there was water leaking from the front left corner from the bottom. I have owned the washer for only 2 years, and Maytag manufacturer (Whirlpool) told me that it was going to initially cost $80.00 for a service call and then more money to fix the leak. WOW. Also the wood floors that are underneath the washer and dryer, is starting to warp from the leaking washer. I would recommend DO NOT BUY A MAYTAG APPLIANCE. The warranty is basically worthless along with the washer.

I have owned this Maytag washer model # MVWC360AW0 since Dec/2013. I do not have a single complaint about this machine. It has worked flawlessly for 5 years and am very happy with it. I just follow common sense maintenance like cleaning it once every month (do a full cycle with just borax & baking soda 1/2 cup each) no clothes of course. Another thing I do is to leave it open after I am done washing so it dries completely before I close the lid. The washer looks and works like new, cant be happier...

Purchased a new Maytag washer from a local Hardware store chain. Waited 3 days for delivery. Old washer was hauled away. Started using new Maytag Centurion the same night it was received. There was a funny odor coming from the washer that was discounted as new equipment smell. Saturday the Maytag Centurion washer was leaking some odd lubricant that had the same odor as the mentioned new equipment smell. Since this lube had been leaking out in close proximity as the liquid detergent my wife used a towel to clean it up. This towel went into the laundry with other clothes.Now Im concerned that whatever this oily stuff is, it’s in all of the clothing that was washed with the towel. Since I live on the West Coast and Maytag only answers the phone during the week Eastern Daylight Time I will call (2 days) after the fact. You might do well by finding out what this lube stuff is before you take it home and how youll have to deal with it once it leaks.

April 26, 2011, I purchased a Maytag top and bottom fridge from Home Depot. After a few days, I noticed frost starting to form in my frost-free freezer and the fridge wasnt really that cold. I adjusted the dials thinking that may do the trick. Nothing changed, it was all the same and instead, frost was thicker. I contacted Maytag, which by the way was taken over by Whirlpool. I told them my situation and since I had just bought the fridge, I wanted a new replacement. They told me things didnt work that way, that I had to honor the warranty. Fine, we are almost entering October now. I have had several services calls, I have written to the Better Business Bureau, I have lost a few hundred dollars worth of food for it would be full of ice and had to be thrown out, I have contacted the executive offices of Whirlpool but they, along with the Better Business Bureau are not doing a thing. Tomorrow, once again, I am having a service call and once again, I know the issue will not be fixed. All I wanted was to either get my money back, along with extra for the loss of food or for them to just exchange it for another one, since this one was purchased with a problem. I really dont think that its right that they are able to get away with this. Just looking at this page, I see that there are plenty of people with this same issue. What is being done about it? If it were them with this issue instead of us, you know ** well they would have had a new fridge the following day. Here is my model# M1TXEMMWQ and serial# VS04658359 for this fridge. Please, I would really appreciate some help here.

I paid $958 + tax for a Maytag Bravos washing machine in August 2008. I live by myself, so the machine is not overused. Nevertheless, it began to sound like a jet airplane during the spin cycle. And then in May of 2012, it failed with error code F51, catastrophic failure. The machine was not even four years old. I called a certified Maytag repairman. In less than 5 minutes, he told me the cost to repair would be about $900, and then he charged $115 for the service call! A call to Maytag resulted in Im sorry, there is nothing we can do.

Maytag MFD2561 - The metal piece between our French doors is also rusting. It is a design flaw. We also have a GE French door refrigerator and that piece on it is not metal!

Our problem started when the control lock button locked itself on. Called Maytag and told it wasnt covered by warranty but they did walk us through resetting the power and it fixed the problem until we ran the next load. Now when you try and set it, the rinse only light comes on. Bought the Maytag because I always believed them to be dependable - wrong!! I had a basic model Whirlpool running for a family of 5 for 25 years prior to this Maytag without ever having to call a repair person. Maytag wont deal with the issue so I would recommend to anyone else having any issues with unreliable appliances to do what I am doing - boycotting Maytag!!

Maytag washer, model# mvwp575gw0, which is under warranty. This washer is less than one year old. Within the first couple months the transmission leaked oil and service tech had to replace the transmission. A few months later – another problem, clothes wet after spin cycle - tech told me the agitator base and/or couple parts need replaced. Quality control appears to have been lacking at the factory when this washer was made. This house has only one person presently. The washer was not abused.

I had the microwave serviced and they heated a cup of water which was fine. I heat food on the tray and only one side gets heated. I have to turn the plate to heat the rest of the food. I never had that problem with a turntable microwave. I cannot understand why they are still selling this inferior product. Maytag used to have excellent products. What happened to this company?

I purchased this Maytag Bravos machine because I was told it can wash large loads and is one of the best washers out there... Both are so far from the truth, this is the worst machine I have ever owned. The water level is almost none. And my clothes come out dirty and I have to wash several times to even get them semi cleaned. I am not rich and trying to save enough. To buy this machine was not easy and I am now with no options. I called Lowes after a couple day after I got the machine and told them it is not working. They sent me another machine yet it still does not clean my clothes. I wanted to return it and get a better machine but they refuse to allow me to do so because now it is 2 months old and past the 30 day return. I purchased an extended warranty which is useless cause. The machine is junk even when working as it should... I will never buy from Maytag again because they refuse to back their crappy product and refund my money. I would tell anyone looking for a washer to not go with Maytag. They are terrible machines and a bad design... I even contacted Maytag and was pretty much told too bad and just rewash my clothes as many times I need but they will not do anything to resolve this issue. TOO bad is what I was told...

This has the aqua cleaning technology, sounds real good. DOES NOT WORK! The cleaning is done by you as you nearly climb into the oven with a plastic scraper which they supply to scrape prior to the cleaning cycle. Then after you have used the distilled water in the bottom of the oven during the cleaning cycle (steam), you climb back in to wipe out the water and use something similar to a magic eraser to SCRUB the oven.Here is the real kicker....during the cleaning process, in between the glass (in the door) you develop water spots that cannot be cleaned unless you pay to have a service technician come out and tear it a part to clean it. According to Maytag THIS IS NORMAL and is proven (by their engineers without any documentation for the customers to be able to see) to be normal?? The consequence is a brand new stove will never be clean and it is the first thing you see when you come into my house. I AM EXTREMELY DISAPPOINTED!!!!

I owned an front loading Maytag Neptune Front Load Washer MAH5500 for more than 10 years and first 5 yrs doing 2-3 loads a day for a family of 12 so this machine held up well, and only issue we had with the machine was the rubber around outside needed to be replaced after about 9 yrs.

I had another Maytag washer. It lasted 21 months. BB got me the BravosXL to replace it. I have had it 6 years. It is a piece of junk. Goes out of balance all the time. We are 2 ladies and don’t have heavy clothes to wash. I am washing now. I have put It through a wash cycle. The soap is still on the clothes. I am on my THIRD rinse cycle and there is still soap on the clothes. And I used less soap. Never again MAYTAG.

The digital display on our Maytag Washer model MVWB765FW, bought 3/22/2017, failed overnight (whilst the machine was not operating) after 3 1/2 years. A reputable firm came out and diagnosed the problem, their report concluded that the Control Board had failed and needed replacing: they provided a verbal quote of $525 [ ! ] to do that. The machine cost $600 and based on the expected life for washers (per Consumer Reports) of ten years would have a maximum residual value of $420 based on straight-line depreciation. The retailer from whom we bought the washer told us that he had contacted Maytag and asked them what they were prepared to do about this failure: a week later and absolutely no response from the manufacturer. Apparently Maytag has no concern for their customers or their own reputation. We made the mistake of buying this machine based on Maytag’s reputation and a ten year warranty which appears to cover only parts unlikely to fail! NO MORE MAYTAGS FOR US.

I purchased a Maytag Bravos Quiet Series washer and dryer in 2009. The repair people have been to my house 7 times. The dryer had a useless part on the drum that made a banging noise while running. The washer keeps getting coins and small undergarments stuck in the motor. Every now and then, one of us leaves a coin in the pocket by mistake. I did purchase the extended warranty on the set. The repairperson that comes to my house is great. I would, however, not want to have to keep leaving work to meet repairmen. The machines are not quiet. If you need quiet from your appliances, this is not the set for you. If you do not clean the washer with Affresh or Clorox product, your clothes and your room smells. The clothes are always so tangled after washing; they tend to wear out quickly. Im not sure about this high efficiency washer. I wish I had just purchased a regular machine.

I purchased a 2006 model Maytag Top load Washer and Dryer used 9 years ago January 2010 to replace a 2009 Samsung front load washer/dryer. I had to replace the agitator on Maytag washing machine before I could use it. Fast forward November 2018 the washing machine stopped agitating the clothes, but would spin the water out. I replaced 2 belts and thoroughly cleaned underneath and inside washer to remove soap residue. Maytag washing machine has been used twice a week since 2010-2019 and still going strong. Maytag dryer has never had any issues. I also own a set of 25+ year old Maytag Washer/Dryer both still working.

I’m 41 years old and finally had my first new washing machine. Four days later, while my 11 year old had the stomach flu, it died. Not impressed. Apparently the delivery guys left a note on our file saying there was a defect on our washer and that we needed to contact Maytag. This was news to us when we called The Brick today. I hope they didn’t knowingly sell us a defective washer. Alas, we have to wait until Monday with pukey sheets in the washer.

My Maytag Dishwashers (MDB7749AWW1) control panel failed for the 2nd time. I replaced it several years ago, but this time the part cost was almost double. So instead of a recall they jack up the price to capitalize their mistake. The ribbon cable gets rusted at the bend from the steam over time. No Whirlpool or Maytag or any other products they market.

These machines have lots of service problems, although Im not familiar with the newer models. The function and the features are adequate, and typical. And overall, again, I have no complaints other than shortly after purchasing, there was a circuit board recall for these machines, and fortunately, I had a repairman who knew of the issue, and guided me to a cost free fix. Overall, it has served the purpose well of cleaning my clothes in a decent fashion.

I purchased by Maytag Bravo from Lowes exactly 1 year ago when the gearbox failed. There was a loud grinding sound as the washer tried to shift from wash to spin. Reading through some on-line reviews and complaints it turns out that this is not a new problem and has been known to Maytag for some time. I specifically bought a Maytag because of their prior reputation for quality. Unfortunately, my information was out of date. It is so sad that a company would compromise such an outstanding reputation.

We bought the highly rated Maytag Bravo washer and dryer in March of 2010. In less than a year, the dryer broke down and the drum drive belt had to be replaced under warranty. Last month the washer drum stopped turning. A & E Factory Service quoted $466.87 to replace the bearing that had failed. We have hated this washer since the day we got it. So, it wasnt hard to buy a Samsung front loader and have the miserable Maytag hauled away to wherever badly designed machines go. Trying to wash clothes using high speed spinning instead of water causes excessive wear on the clothes and the machine as well as tying the clothes in knots. It is one of the worst mechanical designs I have ever seen.

Seven years ago when we bought a new house, we bought all new appliances, Maytag Washer and Dryer, because they were suppose to be extra good and sturdy, what a joke. For the past four or five years, I have had to replace the lock on the door of the washer, which means Im without a washer for a week. Since no one stocks the parts because it is such a joke, some repair places wont even consider repairing a Neptune. Seems like since the company stopped making them because of the problems they have, as a minimum they should replace all Neptune washers that have been sold with a reliable washer, front loading in the same price range. I will never buy another Maytag product and will be sure to tell everyone I know not to buy them either.

Bravo XL Washer & Dryer - I have owned this set for just over 90 days and have called Maytag several times just to get insulted. The customer service representative is not helpful at all, and tells me that I am not using HE detergent or that I am using too much HE detergent. Furthermore, they tell me that if a service technician comes to my home and nothing is wrong that I will get charged. So much for the extended warranty and what is wrote on the Maytag site. I explain each time that I am using name brand HE detergent and the recommended amount. The soap dispenser in the machine provides a fill line that I fill to. I have even tried using less detergent as recommended by the appliance store that I purchased the machine from, and still the washer does not clean my laundry and leaves residue on everything. I have even tried using the extra rinse, and extra heavy soil setting which does not make a difference at all.The other concern is that the clean washer feature light flashes weekly. I have purchased the cleaning tabs recommended to clean the machine, and run this clean cycle every time the light comes on. The dryer does not work all that well either and shuts off before the laundry is dry. Sometimes the dryer will show an error of airflow restriction or low airflow. This is confusing because the dryer vent and hose are clean, and the lint filter is also clean. This is so disappointing because I thought Maytag had great products. However, as I read other reviews about these machines and the customer service representatives it seems that there is a systemic problem with the machines and the customer service representatives that needs to be addressed by the leadership at Maytag.

New side by side, water inlet to ice always freezes. Had a service man out, said some tube needed to be enlarged but still freezes up.The ice dispenser is total junk. Keeps spitting out ice after glass is removed and just a poor design. Dont recommend this brand.

I have had the washer and dryer for a little over 2 years. The washer already needs to be replaced as the cost to replace the drum is almost as much as a new washing machine by another brand. Thought Maytag was the very best. I had a GE washer for years before I purchased this set. The GE wasnt broken but THOUGHT I was upgrading..NOT!!! Will not purchase Maytag again. Very unhappy!!!

Called about our upteenth issue with our Maytag microwave. Was told the part was covered but we would have to pay for service. The last tech told us how to wiggle the part to make it work. Paid a fortune and it broke again. They do not care about customers!!

Because it is the high efficiency model, need to leave the lid open so interior will dry and not smell musty. Also, recommend using a washer cleaner such as Affresh or Tide tablet every now and then. But works great!

My Maytag 3000 series washer had to be worked on right after we purchased it. Now it stinks and is leaking. Repairs are going to be over 300 dollars. A part wore out. It should have lasted longer and why does the front loading washer stink. There is no door to open to clean the filter.

I purchased a bottom freezer Maytag refrigerator two years ago. It recently began leaking water onto the floor from the freezer compartment. I just had it serviced and the serviceman told me that it was a common problem. The duck-billed check valve gets plugged. This is a problem with Maytag, Jenn-Air, Whirlpool, Amana, and KitchenAid refrigerators as they all share the same manufacturer. There is a service bulletin out on this that lists hundreds of model numbers affected by the problem (Technical Service Pointer #: W10632338). I think it is criminal that consumers are expected to pay hundreds of dollars to have this manufacturers defect repaired. I tried to find a place with the government to file a complaint, but wasnt clear who had jurisdiction. Perhaps a class action suit is in order. There have to be millions of consumers potentially facing this problem. Anyone with any knowledge of how to further pursue this defect, please comment.

Maytags reputation for quality is gone. Our Neptune washer has had mold, door lock seized up and wouldnt open, and now our dryer drum is cracked. Exaggerating your products reliability is one thing - this borders on corporate fraud.

I agree with everyone else on here. I would give this Maytag Neptune washer less than 1 star if I could. I also purchased this washer 5 years ago when I bought a new house. According to their commercials, the Maytag repairman is bored because their products are so great. I believe it is because the cost to fix their merchandise when it breaks costs so much.I had a 5-year warranty on my purchase and this washer started making this awful noise but the company wouldnt repair it because it was not broken. However, here I am less than 5 months later, and the bearings are so bad, the tube is scraping and falling apart and leaving plastic pieces in my clothes. I have a 3 year old I dont need plastic pieces in my clothes. You know my husband just left me and I do not have the money to spend on the repair ($500-700) nor have the money to spend on a new washer. Thanks Maytag for your great and wonderful service!

Bought a Maytag Dishwasher, model MDB89449SAM1 a little over two years ago and had nothing but trouble with it. Had Repairman out twice before but today he said we would be better off buying a new one! What a piece of JUNK and truly a waste of money! Would not recommend buying any MAYTAG products. They used to be a quality brand but no more.

Bought the dishwasher (model MDB8969SDM0) at Lowes Burlington Canada beginning of September. After two months of use, the plastic pins and attachment to the drum, top rack broke and cracked in several places. Called Whirlpool Canada for repairs many times and got the run around, spent hours on the phone and still not resolved as of December 12, 2014. This model has a problem with the plastic and breaks continuously as seen by many reviews on the internet. The technician said that this is a problem with this newest model. I have now been waiting for over two weeks for the parts with no end in sight since they claim that the parts are back ordered. Called again today and was told that it would be another week to see if they can find the pieces. This is ridiculous, I paid over $ l,000 dollars for this model and it looks like now that I will not have it repaired by Christmas. Lowes refuses to help me because they have washed their hands since it broke after one month. I have been lied to many times by customer service at Whirlpool Canada. They claim that I am the first one to complain about this model yet the reviews on the internet are full with this issue. They say what you want to hear and do not seem to care at all. It is a disgrace, I feel totally cheated and robbed of my hard earned money. Maytag is no longer a good company for their appliances and service. I am starting to think that I am stuck with this machine and that they have literally robbed me of $ l,000. Shame on you Whirlpool and Maytag.

I have had to put two 50 lbs sacks of feed on top of my Maytag Neptune Washer to keep it from walking in my washroom. Looks like I am not the only one with this problem.

Very easy to use- just dial the button to the load of your choice! The only problem I have is it becomes unbalanced sometimes on a heavy load. :( And it is also energy efficient and lets you know when it needs cleaning.

This machine that I bought 2 1/2 years ago is very loud. Sounds like a helicopter that is going to hit the house. Last week the machine did not empty and would not spin. What a mess. We had to take the clothes out and try to wring them out by hand. Then we had to scoop all the water out. Had to call a repairman to fix it. $187 which included two trips to the house and a new pump. The pump was $56. Just the last year my grandson came to live with us, but before that there were just two of us in the house to do laundry for.

We purchased the washer and dryer in June 2009. This past weekend, I noticed that the washer was leaking. The price to fix it is half of what a new machine will cost. I am very disappointed in Maytag. When I purchased the machines, I thought I was purchasing a quality product. Ive had paid much less for washers that last longer. Needless to say, I am shopping for another washer this week and it will not be a Maytag or Whirlpool. They are pieces of junk!

Maytag Bravos Washer 300 Quiet Series Model MVWB700VQ0 - Nothing about it is quiet. Worked pretty well the first year. Spin cycle works too well. It twists and rips. The second year it needed a new pump because a dime got into it and cracked the pump. When you wash anything bulky you better sit and watch it because it will almost certainly go off balance. Year three Sd (suds or slow) code started flashing and washer stopped half way through. Not sure why suds because I only use HE Tide, no perfumes or dyes due to my daughters sensitivity. I use Affresh as directed and on schedule. Was told it was a slow drain, found two dimes in the filter and a lot of lint. Still not working and flashing Sd... stops half way, agitator moves left to right doesnt spin. When the diagnostic was performed, the basket spun but when it stopped it made a grinding noise. Now it might be that it needs new bearings! So much for the Maytag reputation. Its junk and I will not be buying another Maytag, Whirlpool, Kenmore or any other product from their affiliates. Not purchasing anything from Sears again either. Also I will be canceling my subscription to Consumer Reports because they highly recommended this product. Shame on Maytag. How do we start a class action suit?

The dishwasher is very stylish and looks great in our kitchen. I do wish there was a small knife drawer in top. It cleans very well and is super quiet. I would highly recommend this dishwasher, good value.

Perfectly great, cleans anything, not terribly quiet, but results are more than satisfactory. Good water pressure, cleans every nook and cranny, things come out spotless. I do not have anything else to compare, but I think the size is fine, I can put a lot of stuff in it. Controls in front at top, easy to use, clean appearance. Even though my dishwasher is 13 years old, I have not had any trouble with it. The top racks are strong and hold a good bit of glasses, cups and bowls. I have put baking pans, cookware, grates, and a lot of other stuff in to wash and it all came out clean.

I purchased a Maytag dishwasher in 2013 and the control panel needed replaced within the warranty period. About a year later, the control panel started to malfunction again, this time out of warranty and Im told it will cost over $350 to repair. I paid a lot for this dishwasher and thought I would get years of use out of it. I plan on buying a new cheaper one (not Maytag) for a little more that the cost to repair the Maytag. Im very disappointed and will not purchase another Maytag. I also read online that Im not the only one experiencing this problem.

I have a new Centennial Maytag dryer. What a horrible sound it makes when the time is up!!! I had another Maytag dryer for 19 years and it did not sound as obnoxious as this new one. HELP!! I can tell some man invented it.

Bought machine 03/23/15 exactly 2 yrs ago & machine will not work. It looks like the electric panel and which there are a lot of complaints about the panel, and the lid. It seems as its about the extended warranty now. The quality that Maytag advertises is lies. You buy the product and you have no choice but to purchase a warranty on your machine. Simple is better when it last 20 yrs over 2 yrs on a fancy machine. First electric panel machine washer with a horrible experience. It will cost 98 just to look at, that is not including parts and labor. Its 339.15 for a year warranty which equals over 300 per year for 3 years. Overpriced in all ways. Worse choice ever.

They are coming for the 7th time to fix the ice maker. Three full replacements. The bottom of the freezer had a buildup of ice, another call to repair. I know where the Maytag repairman is, hes at my house.

Do NOT purchase a Maytag dishwasher. What happened to the Maytag repairman being so lonely. Now he has lots of company in the way of angry consumers. Purchased a Maytag dishwasher and less than a year later the control panel failed. It was still under warranty but the service person just tweaked it instead of replacing it. Now, less than a year later it has failed and will cost over $200 to replace and repair. This is disgusting.

Our Maytag microwave MMV4205FZ-0 has the same ubiquitous problem as so many reviewers have mentioned. The microwave refuses to turn on (always at the most inopportune moments--like when the entire family is over for dinner. It doesnt matter how many times you open and close the door, it will often refuse to start. I think the worst part about this situation is that there are so many reviewers experiencing the exact same problem. Imagine how many havent posted a review. Doesnt it seem as though a rethinking of the door switch would have been in order long ago along with a recall? The fact that hasnt happened after so long and so many customers who are disappointed in their purchase is a sad commentary.

Maytag Maxima 9000 washer not working since day 1: I have placed a call on Friday, June 14, about my Maytag washer not working. The service man came in on Friday, June 15, 2012, and stated that a UI board needs to be replaced. I have called Whirlpool to ask for the part to be ordered so it is faster, could not do anything. Then, I have not heard from Whirlpool since. I called them again on Wednesday, June 20th, and I was told that the part was ordered and it will take up to 10 days for it to arrive. Once it arrives, the technician will call to set up an appointment. So, according to Maytag (Whirlpool), I can be without a washer for at least 2 weeks (as 10 days are 10 business days) and it is all good.

Control panel on front of dishwasher quit. Unit is 15 months old. Bought extended warranty through Home Depot. Took two hours on the phone to finally get to the correct department, they set an appt. for the following Wednesday between 10-2. Had to take a vacation day. Get a call from the appliance repair co. the night before stating they cant live by Depots schedule, they wont be out til the following Monday between 9-1. Schedule a vacation day. They come out then have to order parts, they wont be in for 7-10 business days. After 12 business days, I call back and they set appt. between 10-2. Schedule vacation day. They come out and the control panel the warranty company sent is the wrong one. Now I have to start the whole process over again. DONT BUY MAYTAG AND DONT BUY WARRANTY OR APPLIANCE THROUGH HOME DEPOT.

Ive had my washer for about two years and have been disappointed from the get-go. I did a lot of research and found this to be top rated... Wrong! Even though I use the HE detergent and Ive even cut down the amount with no results, it leaves gobs of soap/lint residue on most of my darks and I wind up having to either rewash on clear or rinse by hand to get rid of the stuff.Ive also noticed some snagging on some brand new towels, but I attributed that to possibly the brand. Well, then I had an issue with some very expensive bottom sheets shredding and raveling and still didnt catch on. Today I noticed a different towel with similar problems, which led me here and walah! I see Im not the only one having these issues… Darn! Warranty is expired and Im stuck!

Purchased this machine (Maytag Bravo Washer) in May, 2015. Drive motor blew Jan, 2017. 18 mo. old. 10 year parts warranty and a tag on the machine that reads MCT (Maytag commercial Technology), which leads the consumer to believe this heavy duty machine. I called the warranty number, as I had properly registered the machine on the day of install. Said he would have a new drive motor out to me in 7 to 10 weeks. Yes. WEEKS. Really? I advised the operator that 3 parts stores in my area had the part available, and asked if there wasnt something we could do. He said no they are back ordered. How is it that Maytag cant get their own parts. I purchased the motor for 118.00 and my clothes are now washing again. NICE job Maytag. I suggest finding another company to buy your appliance from. Promises made are not promises kept. DO NOT PURCHASE THIS MACHINE.

Purchased our Maytag Bravo Quiet Series 300 about 5 years ago and came to this site to read about other washing machine complaints because I am looking for a new washer. Was SHOCKED to hear so many similar complaints to mine (our local appliance store who sold us this unit, as well as services it, said this was unusual). Tiny holes in all our clothes! Black marks on clothes! Dirty clothes! LOUD & BUMPY washing - will sometimes walk itself around the laundry room, slamming into wash sink & dryer (there are dents to prove the violence). UL light that stops the machine & cant be resolved even after I untangle & lift water-soaked items. Finally started seeing black marks splattering out from under machine & was told the bearing is bad and the case (?) is leaking? ... Anyway, result to repair is MORE THAN ITS WORTH.Also have a 3 year old Maytag Quiet Series 300 DISHWASHER, that does not clean well, sometimes leaves half the dishes untouched (dry & dirty), grinds food waste & redistributes onto dishes before baking it on tight (requires soaking to loosen, then wash by hand) ... Oh, and is NOT quiet! I was told I probably use TOO MUCH SOAP. Seriously?!? My complaint is NOT soap residue ... It is D.I.R.T. How can you run a load and still have sauce & ketchup that dripped onto the inside of the door when loading the dishwasher STILL on the inside of the door??? Darn thing cant even clean itself!

The Deli drawer randomly falls, shelves in general do not fit well. Rough edges on door corners are a hazard especially for children. Service call line was extremely poor with a total disregard to customer concerns. It has been a very bad decision!

I will NEVER get another Maytag product ever again! My not even 1 year old washer broke and I have been waiting almost 2 1/2 months for a part to be replaced. My partner and I are nurses working on the front lines during this COVID pandemic and I can’t even wash my scrubs at my own house but instead I have to go to a damn washateria. The “supervisor” told me 2 weeks ago that if the part is not in by today, 1/27/21, that a brand new washer will be sent to me. Well I call today and the people I spoke to denied any recollection of this information. The “supervisor” stated that she is “documenting all of the information” so when I called back I would not have a problem. Once again I have been lied to and wasting my breath and time. The customer service has been TERRIBLE and I cannot believe that this was once a “reliable” brand! Clearly this brand is unreliable and the personnel is also unreliable. NEVER AGAIN WILL I BUY A MAYTAG! Save your money and buy a different brand!

When we moved to a new home, we upgraded all the appliances, including the microwave. This was four years ago. When the first microwave stopped heating the food after two years, we thought it was a fluke and bought a brand new one, since fixing it would have cost more. Well, I should have gone with another brand. This is two Maytag microwave ovens in four years! We cannot believe that a company who enjoys such a good reputation can get away with such shoddy products!

In August my GE refrigerator of 22 years bit the dust. Went to our local appliance center and purchased this unit for $2100. Have only had it a month and am so dissatisfied with the water dispenser, ice machine and doors, I want to return it. I cant wait for all the other things to go wrong with it. I dont know who the engineer was behind this but he needs to be fired. I really wish I had reviewed this refrigerator before purchasing it as I will never recommend Maytag again after reading all the bad reviews. The name Maytag used to mean something dependable and made well... Rant over.

Purchased dryer less than 6 months ago and now have an issue with the powder coating bubbling up and flaking off on the dryer drum. Maytag says not covered under warranty unless found in less than 30 days. If I had know that I would not have purchased the dryer.