Dryer wont dry/ service at dead end. So in 2018 we purchased a Maytag Bravos washer/dryer set. The washer does its job, it washes clothes acceptably. The dryer, which has the sole purpose of drying clothes, DOES NOT dry clothes. It leaves each and every load damp. Two to three cycles are required for even the lightest fabrics to dry. This has been the case since the product was new. After repeated attempts to have the dryer replaced, I am fed up with the whole run around. MORAL OF THE STORY IS DO NOT BUY MAYTAG.

Series 200 dishwasher wont start. Just over 1 year old. Control panel needs replacing which I found out, is a constant problem and a design flaw. Called Maytag and they would only offer 25% off new part. Why would I do that when it is just going to go bad again?

We purchased a Maytag dishwasher MDB7609AWS2 in October of 2010. It first stopped working about 2 years ago. Since it was only 2 years old, we were disgusted and decided to let it sit and do dishes by hand. About 2 months after it had stopped, we tried it on a fluke and it worked. It stayed working for about 2 years. It finally stopped again, so we did the same thing, just let it sit. Every once in a while we try it to see if it works. It just recently started working again. We are wondering, what is up with this. We are not sure why or how the sitting works, and it is ridiculous that you have to have an appliance that you cant use periodically. We were too stubborn to have it fixed or buy a new one at this level of newness. We will get by in this manner for at least another few years, so as not to have lost all of our investment in a dishwasher, but we have sworn off Maytag appliances forever.

MBD7709AWB2 - Bottom line, every 1.5 years (18 months) you will have to buy a control panel. Number 3 for me cost me $149.00. Now my wash cycle will not kick on. Do I have to tell you what dishwasher not to buy!

Received new washer & dryer on Oct 2nd, 2015. The dryer has been acceptable, but the washer has been one problem after another. First of all the washer is so noisy beyond belief. The engineering is one dreadful design. At first attempted use, washer would not begin cycle. Sensor would say lock, unlock, lock, unlock for so long, I would cancel & begin again. It became such an annoyance that I placed start of cycle on a timer (it sat at sensor mode for 20 min.) then I restarted next time sat for 15 minutes without starting. After beginning from start position it would start OR NOT. First repairmen told me timer might be off a bit. As days passed with same issue, second repairmen arrived and found that door was off (not completely closing). Repairmen would place an order for new seal. Upon repairmen arriving for third time (new seal did not solve issue) he believes that lid is uneven, & he will order a new lid & return in a few days to repair. I must admit that service has been quick, but the issue is still a headache. I would NEVER recommend this model to anyone and would like for Maytag to replace washer with a different model. The noise is a factor that no one should have to endure. The grinding noise can be heard from three rooms away from laundry area with laundry room door closed! Im absolutely a very very unhappy customer.

Purchased our Maytag Bravo Quiet Series 300 about 5 years ago and came to this site to read about other washing machine complaints because I am looking for a new washer. Was SHOCKED to hear so many similar complaints to mine (our local appliance store who sold us this unit, as well as services it, said this was unusual). Tiny holes in all our clothes! Black marks on clothes! Dirty clothes! LOUD & BUMPY washing - will sometimes walk itself around the laundry room, slamming into wash sink & dryer (there are dents to prove the violence). UL light that stops the machine & cant be resolved even after I untangle & lift water-soaked items. Finally started seeing black marks splattering out from under machine & was told the bearing is bad and the case (?) is leaking? ... Anyway, result to repair is MORE THAN ITS WORTH.Also have a 3 year old Maytag Quiet Series 300 DISHWASHER, that does not clean well, sometimes leaves half the dishes untouched (dry & dirty), grinds food waste & redistributes onto dishes before baking it on tight (requires soaking to loosen, then wash by hand) ... Oh, and is NOT quiet! I was told I probably use TOO MUCH SOAP. Seriously?!? My complaint is NOT soap residue ... It is D.I.R.T. How can you run a load and still have sauce & ketchup that dripped onto the inside of the door when loading the dishwasher STILL on the inside of the door??? Darn thing cant even clean itself!

Purchased our Maytag Centennial Washer Model MVWC400XW4 2 years and 5 months ago; guess we are luckier than most; it has now failed in the spin cycle, high pitch, high volume whine, sounds like it is about to explode. Needless to say is out of warranty; and too expensive on our limited income to have a technician repair. I will hope to make the repairs myself; nothing to lose at this point; and from reading the countless negative reviews about this product; should be as many countless repair suggestions on YouTube. Obviously if Maytag would stand behind/up for their product as they claim they do; I and many others would not have these issues. My wife and I for sure will never buy another Maytag product until Maytag resolves the issue, which if my calculations are correct will be never. My advice is simple, do not buy Maytag products.

Have owned Maytags (washer and dryers) for 40 years. I bought a Bravos top load washer and matching dryer because we gave our old set to a daughter leaving for college. That was less than four years ago! We bought this because it conserved water and there would only be my husband and myself home. So laundry needs would be minimal. The washer quit draining and starting making a terrible noise several days ago. Immediately called repair service - I knew from the onset this was going to be a big problem because when I told them the model, they responded - uh oh! Two days later service man comes to assess repair and lifts machine up and tells me bad seal has leaked to gear box and ruined it. Soooo for a machine that is less than 4 years old, I will have to pay $280 for part, $79 for service call, $60 for labor and $35 to have them pick it up and redeliver (because the repair is too big to be made in my home). $454 for a machine that gets minimal use!!!! I can add another $100 plus and buy a brand new machine. Why should I have to??? In doing some research, I found out this is a common issue with this model and Maytag has paid for the repair of other washers because it is a common problem. Even the serviceman said that and recommended I get a hold of Maytag. Their response - sorry mam you dont gave an extended warranty. (NOW I HAVE A LEMON!) Guess my next step is to write a letter to Maytag Corporate Office. I will keep going up the ladder until they address this flawed machine problem! One thing is for certain - I will never ever buy another Maytag product of any kind or will I ever recommend it. They are just not reliable. Guess, nowadays they are considered throw away products - keep them a few years and throw them away because its not worth your money and effort to repair them :-(

The ranges are getting great but are more so with digital than buttons and knobs which they should still have, especially for the handicapped and some elderly who prefer them. It would help prevent injuries. It was hard for me to find the knobs.

The engineers at Maytag saved a few pennies by only using one thermistor for temperature control. It is in the box. There is nothing monitoring the temperature in the freezer. If you put your fridge in the garage where the temp is 40 degrees, the motor will never come on, and your frozen foods will melt! In my new MRT118FFFZ01 unit, the temperature in the box varies by plus or minus 3 degrees F, but the freezer varies from minus1 1 to plus 25 degrees F. 36 degrees difference! Lousy design. Have had two service calls, and they both said that this was the way it was designed and there is no fix for it.

Purchased a Maytag Electric range Model MER8800FZ2 in 2019. The surface Scratched the first week of purchase and the stains will not come off. When I called customer service they claim they are not responsible for cosmetics. In my opinion, This model was put together with the cheapest material they could find. Maytag is not what it used to be. The Elements take a long time to heat up. Inside the oven, the Glazed Paint is cheap product also where once it stains with food it never comes off.

We bought this Maytag Bravos top loading washer 2 years ago after having bad luck with a front loading Maytag. Maytag was always the top brand to buy so I thought it was the style washer but now I believe Maytag has failed to keep their standard of quality high. My clothes come out of the washer almost dry and full of lint. Even though I use the HE wash soap, it does rinse out of the clothes. Dark clothes come out with a noticeable scum so I suppose the lighter clothes do, as well, I just cant see it. I sometimes have to wet the clothes down to get them clean and I always have to double rinse them which defeats the whole economy issue. Im not happy with this washer and would not recommend anyone to buy a Maytag brand washer.

We built a new home in 2008 and purchased a Maytag appliance package from Home Depot, including a dishwasher, stove and refrigerator. From the beginning, we had problems with our French door refrigerator (MFC2061HEW; it has been discontinued). Within the first year we had 3 ice makers replaced because it was not making any ice. Now, mind you, we went through Maytag to have their repairman to service our appliance and they set up all the service calls. We limped by for awhile and called a different repairman to come and check the fridge because it was not staying cold or making ice again and, of course, it was out of warranty. The first thing he did was check the freon and we were told that it didnt have enough freon to keep it going, so he recharged it and it worked great. We have had to have the repairman come back again this month because it stopped making ice and the temperature for upper and lower was all over the place. He checked the freon again and said the unit has a slow leak in it and he was unable to fix that. I contacted Maytag because I felt if the first repairman had checked the freon from the beginning, we wouldnt be having this problem. The only suggestion I got from them was call a company with a dye kit test and that they are sorry, but its not under warranty. I dont know about anyone else, but $2000.00 for a fridge that has been a pain since day one is a lot of money to replace. I feel they dont care about their customers and they should be responsible for paying for the repair that should have been caught from the get-go.

Purchase a top loader washer machine in Nov 2014, it is now Jan 2015. It is not completing drain cycle, leaving wet cloth. I am Not happy with the service. I had the tech people come out 3 time and saying to call customer service, and they keep sending out people. They do not want to give me back my money. Unhappy, waste of money, will not get another Maytag appliance again.

Maytag/Whirlpool dishwasher control panel FAILURE MDB7749SAM - Just like all the above comments about this dishwasher... I too have been a victim. Control panel stopped working after 1 1/2 years. Turned on by itself like other have commented and will not let you push any buttons. Maytag/Whirlpool refuses to do anything about this at all and will cost me over $250 to fix an appliance I purchased at $499. How disgraceful of a company to not stand by their product... A huge shame on you Maytag/Whirlpool for not standing behind your product. If anyone knows of a way to get involved with a class action suit against this company I would like to get in on it.

My son gave me a Maytag washer for Christmas 2013. I hate it. Sometimes it takes me 5 tries to get my clothes washed, and then it dont go all the way through the cycle. I have to constantly check on it. I hate it. Can you give me some tips on what may be causing this... Very disappointed.

CHRISTMAS morning Set oven to 325 for ham. Control board caught fire and burnt wires and burnt inside of rear cover. It got hot enough to char the wood wall behind stove. This could have killed my family on CHRISTMAS.

Our prior fridge died on a hot long weekend in July 2020. Desperate for a fridge, I ordered any fridge that could be delivered the same day. Received a Maytag which totally died 3 months later! Now I am waiting for a part (which apparently the Manufacturer has 100 in their inventory but havent distributed them to the source that ordered them). This is just the worst service I have ever experienced with an appliance. As so many people have said, I should have waited and ordered a European appliance. They are built beyond perfection and have excellent service.

My wife and I bought a Maytag Bravos at the suggestion of a store employee at Lowes. Since we have owned it, I have seen the reviews and the washer has been a total let down. We have experienced all the same complaints. Loud noise, door lock not working, not enough water in the drum to wash clothes, and the bearings going out and it doesnt work. NEVER will we buy a MAYTAG again. To the scrap yard I go today. Thanks MAYTAG for wasting my money. Thanks LOWES for recommending this garbage.

Maytag Centennial - It came with the house. I think its a line made special for rent-to-own kind of places. I cannot stand the washer. It will not take fabric softener unless its in the ball and if you use extra rinse you dont get to use fab softener at all. (I like liquid fab softener on some things). Why it doesnt have a dispenser is beyond me. And the bleach dispenser is poorly designed, too close to the tub and splashes every time. Ive had this six months and would get rid of it in a heartbeat if I could afford to. Plus it snags towels. The washer is crap. And its a Maytag. I wish it would break so I could justify buying one that has some decent features like fab soft dispenser, bleach dispenser that doesnt splash, drum that doesnt snag.

How many times do we have to go without a washer? We have to wait on service to check/see how many times it has to be fixed. This is since we bought it.

I live alone and bought this unit for long life. After a few short not-used-much years, my washer sounded like a 747 was landing in my laundry room. I am a maintenance person, so I did a bit of troubleshooting and narrowed it down to the bearings installed in plastic on the outer tub that failed. My cost was $600.00 to $750.00, parts alone. It still worked, just very noisy on high spin.I emailed Maytag (now Whirlpool) and was phoned by Lee Ann. I told her I had all Maytag appliances in my home and was laid off and that if after the use this washer has had and it will cost this much if I do the work, I was not impressed with this company. She apologized and told me she will issue me an extended warranty for $299.00 that will cover it. I told her that without a job, I cannot make a decision so fast. She gave me the next business day to decide. I concluded it was cheaper than the part, so I called her back. I was scheduled for a repair, and the man opened the front and looked at it and said it was an outer tub bearing. He went to his laptop in his truck and returned to tell me that they would not authorize that expense and that all they would authorize was $350.00. He put the front of the washer on, then as if he forgot something, took it back off and reached way in the back and did something. Then, he reinstalled the front. I was livid! They charged me $299.00 for a warranty and would not repair! So I called back and was hung up on. Next, I called my credit card and disputed the charge. I tried to use the washer, and it made funny sounds and then filled up my home with smoke and stopped working. I called Maytag again, and he denied the repairman would tell me how much they would authorize to repair it and told me good news that they would issue a $174.00 check. I gave $299.00, and a few days later, they give me $174.00? This is why Whirlpool is destined to fail. I will never buy again, and I will wash in my laundry tub first! This is exactly why imports will rule! So Whirlpool, you got me for the last time!

I bought the power wash Bravos XL... Bad. It does not rinse the clothes, leaves residue on dark clothes.. probably all clothes - cant tell on lighter colors. I dont recommend!!! Waste of money.

Purchased side-by-side with bottom freezer 2009 after Hurricane Ike. Fridge has stopped cooling. Called Maytag Customer Center and was told nothing can be done only to find theres a 10 year warranty on the compressor. This malfunction should not be an issue after 8 years. My GE fridge still works after 25+ years. Horrible!

Maytag Dishwasher Model # MDB7749SBM1. What a piece of JUNK! Purchased in June 2013. Control panel went out six months later! June 2014 Control panel BAD again (#2). March 2015 another Control panel replaced (#3). Thank God for Home Depots extended warranty! October 2019.... Control panel needs replacing!

I bought a new Maytag dryer model # MEDC555DW2 18 months ago. Prior I had owned a Whirlpool for 22 years and the only expense on maintenance was that I replaced 3 belts. This new Maytag started making a terrible noise so I called the store where I bought and they sent out a tech. $76.77 they charged me to...remove a penny from where it got lodged in the edge of the drum somehow. Maytag refuses to do anything about it and I feel like Ive gotten the shaft because I bought an inferior product. In 22 years Id guess I dried on accident over 100 dollars in change since I have kids. Should have bought a Whirlpool again and so should you. Ill never buy another Maytag product. Ever.

Model MDB7749AWB2 Dishwasher - we purchased this dishwasher 3 years ago on 12/23/2011 and it appears to be falling apart. We have replaced two thermo fuses, one door latch/switch and now need the front control panel and handle because two mounting locations for the six screws have broken off. I truly expected a much longer product life than three years when I purchased a Maytag. So much plastic in crucial high stress areas must have slipped by the engineering folks. Or was it just cost cuts. I believe it will be a long time before I consider a Maytag product again based on this one. Thank you.

On 9/8/09, I purchased a Maytag ceramic glass top range, model MER7662WBO. The right front dual burner has what look like worms in the burner. The other burners are clear. Maytag has replaced the top three times and the burner once. The top has gone bad again and they are calling this a cosmetic now and will not replace the top. I think there is a problem with the tops. I have purchased my last Maytag product. I buy for looks also.

I absolutely do not like the fact that you can’t choose what size load you have. The washer wants to do it for you but it is not very good at it. You have to fool the washer to get any kind of water level or just use the deep fill every time which is what I do in order to get the clothes clean! This defeats the whole purpose of trying to save water. Also there are too many settings. I mean we’re just washing clothes here not flying a jet. I personally would prefer dials instead of the digital instrument panel. So much easier.

I purchased a French Door, Bottom Freezer refrigerator in the summer of 2006. Less than 3 years later, the ice maker door kept opening and closing and the lights on the door panel kept flashing. I called Maytag and found out there was a problem with the circuit board, and that it was under recall. The refrigerator was fixed at no charge and I was happy. Approximately 2-1/2 months ago, less than 7 years after I bought the fridge, it started getting too cold inside and then too warm and then too cold, etc. Then it stopped cooling altogether. From what I read, it was either a problem with the compressor or the relay on the compressor. There was a recall on the relay on some models, but not on mine. I cant even afford a service call. Let alone a repair charge. If the compressor is the problem, Im looking at a repair bill in the hundreds of dollars. The online price for a compressor is over $300. I dont have the money. So the beautiful refrigerator that I paid $2,000 for sits in the kitchen, unplugged. I never figured that Id pay that kind of money for a refrigerator and have 2 major problems with it in less than 7 years. I just got off the phone with Maytag and, of course, they cant do anything to help me. I was hoping to never buy another refrigerator, but if I have to or if I have to buy any other appliance, I will never ever buy another Maytag or Whirlpool. I will post everywhere I can about my experiences with this refrigerator.

Both Sears and Maytag have lost my business FOR GOOD! We purchased a Maytag Bravo XL # MGDB980W0 2 years ago. We called within the 1 year warranty period via Sears, they sent a tech out then charged us. The dryer kept shutting off before clothes were dry. We thought the problem resolved, then reoccurred after the 1 yr period. Neither Sears or Maytag would stand behind the product citing it has been discontinued due to problems. Well... yeah, no kidding. We paid BGE energy efficiency company to come out and evaluate it. They tweaked the exhaust vent and cleaned out the duct, however, they said we needed a new sensor. My wife bought a new sensor, installed it, and the dryer still wont work right! (Shutting off prior to clothes being dry). BOTTOM LINE UP FRONT: I researched and bought a new gas LG dryer on sale at Home Depot and shelled out $849 unnecessarily thanks to shoddy product and lack of company integrity. DO NOT BUY SEARS OR MAYTAG!!!

I have a Maytag washing machine for close to 20 years, so when it was time to replace it, I bought another Maytag: the Bravos. I read reviews, and most negative ones complained that it used too little water, twisted clothes, and was noisy. But I wanted an HE and can tolerate noise just fine. What I cannot tolerate is the fact that -- less than 2 years after purchase -- the control panel is malfunctioning, and it will cost $500 to repair. Id rather buy a new washing machine than throw good money after bad on this one. Bye-bye, Maytag.

I take pride in my cooking and love my kitchen. As you know this is where everyone gathers when you are entertaining. The Aqualift system does not work. I have run the process 3 to 4 times consecutively in row and the inside oven the oven is never clean. I wipe out the sides over and over. So disappointed. The only saving feature is that you can not see into the horrible look of the inside the oven when it is closed. Was this feature really tested before it went to market????

I purchased your refrigerator (model #mfd2561heb) in 2005. I bought a Maytag, because I thought it would last me a lifetime. I came to find out it will not. I called Maytag, and got Repair Plus One. The repairman came out without a compressor or capacitor. Now, I have to wait 4 days or more. I have a 3 year olds birthday party, of which we will be working out of our 19 year old Kenmore in the garage, which has worked flawlessly. To make it short, you lost me as a customer, because of this product! I just wanted to let you know. It is sad too, as we enjoyed the refrigerator. Its been making noise for awhile. I thought it was just part of the ice maker. Now, it cost me another $299, plus all the food I had to throw out! There was a big recall of refrigerators from Maytag around the time mine was made. I think that this model should be part of that recall as well. Dont buy a Maytag! They may have had quality at one time, but I just think those days are gone. Thank God for our Kenmore in the garage. I dont know what I wouldve done without it.

We bought a Maytag refrigerator (single-door) with a top-loading freezer that failed after four years. The freezer began to ice up and two repairmen from the company that does the extended warranty repairs in the Ottawa area were unable to figure out the problem. After the second visit, the freezer iced up again and the thermostat appeared to be failing. Even though we had an extended warranty, we just gave up and went to a different dealer to buy a new refrigerator that could be delivered within three days - and it wasnt a Maytag or any other of Whirlpools brands. If youre thinking of buying a Maytag refrigerator, you should reconsider. In fact, you should twice before buying anything made by Whirlpool.

My mother always said Maytags were the best but I never bought a washer and dryer until about 5 years ago and both are the worst appliances I have ever owned. The washer has rust all over the bleach container and smells to high heaven and I clean it with Affresh all the time. The dryer doesnt dry well and the washer doesnt wash well. I am trashing both and buying some new ones.

MFI2568AES - Last night we woke up because of a noise coming due to continuous snapping of the waterline against the walls of the refrigerator as well as a wall of the house structure itself. Very loud noise. I pulled the refrigerator, went behind it, and shut off the waterline. That stopped the noise and allowed me to go back to sleep. However, need your help to resolve this issue. I will appreciate if you can offer me pointers and guidance.

We bought our Maytag Bravo top loader on May 5, 2010. The machine was working fine. Then last week with no warning, the F51 error code popped up. We called Sears and they sent a repairman out. The result was the sensors work independently from each other (tested correct in the Ohms range). It made it through an entire diagnostic test, but will not complete a wash cycle. The repair guy concluded that the control board was bad. Estimated cost to fix was upwards of $400. I cannot afford to fix. Our issue with this product is that it is apparent, from reading all the forums, that this is a known issue. And we believe Maytag should be reimbursing consumers for this repair or they should recall the washer. Our washer is used on the weekends and it should have lasted us for minimally five years. All we wanted was to make it through one military overseas tour with it, not asking much. Instead, this machine lasted two years. Unacceptable.

Maytag Bravos XL: I purchased mine Nov. 9 2017. I so wish I had never bought this machine! It leaves soap residue and dog hair on my clothes and bedding. I have to wash everything 2-4 times. It’s beyond disappointing. My husband and I agree our clothes looked better dirty, BEFORE we “washed” them in this machine.

I purchased a Maytag Bravo Washer and Dryer about 2 years ago; dissatisfied with the products. Washer continues to smell. I clean it all the time with the Affresh tablets. Usually, I have to use 2 bags just to get it not to smell for at least 2 weeks. Now, the glass front dryer is rusting out around the window.

Bought this stove in 2011. 9 months ago I had a 300$ repair for fuses to two out of the five stove top burners. Several days ago the ovens were not lighting and I called for repair again. Well the ignition switch in the lower oven had a frayed wire from the factory which created an issue with the control panel. Today I was quoted 600$ to repair the ignition switch and the main control board. PARTS ONLY. I am not repairing this stove. Called Maytag due to the issue of a defective ignition switch wire and got nowhere. Very poor quality product.

My name is Mrs ** and I dont have a complaint. I would to tell you about our washer. It is a Maytag. It use to be my mother-in-laws. She did laundry in it for 4 grown boys and 1 girl plus her and her husband. She passed along to my husband a long time ago. And now it does laundry for 6 kids plus my husband and me. I run it 2 days a week sometimes more. The washer is between 25 and 30 years old. And works good still. Im not sure how much longer it has but we are happy with it. And soon Ill be washing for 7 kids. We have made a decision to start looking for another soon. But I wanted to share my story with you. My husband is now in his 40s if it says how long it has lasted. Thank you.

Duck bill valve for defrost water from freezer malfunctions, water flows into freezer freezes, then eventually overflows onto floor. Huge problem for folks with wood floors. Also a slip/fall danger especially for the elderly. When the repair line is contacted, they deny the problem and say you are the only one. But if you do your research, you find there are hundreds of complaints and in November 2013 they issue a service bulletin, but its internal, not meant for consumers to find out. So if you have this problem, go to the Consumer Product Safety Commission and fill out a complaint. Maybe then something may come of it.

#Mgt8885x500 Maytag Gemini. After oven heats up, racks fall. What should I do. This is a safety issue. Help, afraid to use oven.

If you are considering this product...RUN AS FAST AS YOU CAN!! This is the biggest piece of junk Ive ever owned!! I would be more than happy to take back my 20+ year old washer over this JUNK!! It is 2-2 1/2 years old tops. I cannot count how many times my husband has already had to repair this garbage!!! I will NEVER purchase another Maytag appliance! My stainless steel dishwasher isnt any better!!

After my divorce, I bought a new house for my youngest son and me. It came without a fridge, so I used some of my settlement money to buy one I had been dying to get - stainless, French door, with bottom drawer freezer! It worked fine for the first 9 months or so. Then, water started pouring through the ceiling of my downstairs master bedroom. Turns out it was coming from the freezer water line. Ceiling tiles ruined, carpet stained. Then it started making this god awful noise. It starts, rumbles for a while (long enough to wake everyone up or give the dog a coronary), then is quiet for a while. Next, I open the freezer to find a sheet of ice across the bottom of the drawer. I assumed I had done something, so I got rid of it and thought nothing else of it. Last night, I get ready to make dinner and there is this blizzard of frost all over the freezer. It looks like a winter wonderland. I am afraid to see what is there when I go home and even more fearful to attempt to use my warranty.

I purchased a Maytag dishwasher model #MDB6769AWB2. After 1 year and 2 months of light use (just my wife and myself), the control panel went out on it! I called Maytag and because it was over 1 year old, they would not do anything about it! When you call their number listed in the owner’s manual, they thank you for calling their Customer Experience Center. This is an experience I can do without!

Maytag French door, bottom freezer - Water accumulating on the freezer drawer gasket. After a short period of time, mold forms which is a potential health hazard. We asked Maytag to look at the problem. So far, 3 service people have come around - each one with a solution, but none have been successful. I called Maytag again and left messages on two different occasions, and they have yet to get back to me. Am I on the blacklist? This I know for sure - this is the last Maytag product to ever get in to my house again. If anyone has a solution to our problem, we would love to hear from you.

We currently have had our Maytag washing machine for approximately 15 years. The first thing we noticed was how user friendly it was. Also, the options that came with our washing machine met all of our needs. The second thing that we were excited about was how quiet it was. Our previous washing machine could be heard at the back of the house and was constantly out of balance. The third thing we noticed was how much cleaner our clothes were. Our clothes smelled better and had less wear thus saving us money. Speaking of which, the machine is an energy saver. One of the most significant attributes I can attest to is how reliable it is. There has never been an issue that required repair services. I am sure our Maytag will be in service for years to come. c

I bought the washer dryer combo. Dryer already broken. Washer is very loud when it changes gears. Would not recommend the washer or dryer.

I had this microwave less than a year. The control panel went out and Maytag fixed it. Now a year and a half later, the same thing happened. This product was almost $400 at the time we purchased it. I have had better luck with $40 microwaves.

I am 86 years old and have happily owned Maytag washers for many years. I just recently purchased the front loading model for ease of access. After using it for sometime, I could not be more disappointed. The clothes come out smelly, stained and gray. I tried using affresh washer cleaner on hot setting and the tablet did not even dissolve. There is black mold growing and must be cleaned constantly. I am so sad that my favorite company has let us down. I cannot afford to buy another washer so I am stuck with this lemon!

When I remolded my kitchen almost four years ago, I purchased four Maytag appliances. There was a recall on my dishwasher that was successfully fixed; the heating coil could have caused a fire. The next appliance to go was my refrigerator with a bottom freezer: the freezer section went. Thank goodness I purchased a policy which covered the repair that had to be done twice--twice I lost food. I was compensated by the insurance company for $200.00 for the cost of food lost. Just before Christmas my microwave stopped heating. The turntable works, the timer works, but it will not heat the food and makes a loud noise. The glass top on my stove is getting marred even though I clean it every time something spills. I keep my appliances in immaculate condition and they look like new. I thought when I purchased Maytag I was buying reliable appliances. Their ad that states that the Maytag repairman is lonesome because he has no work is a lot of bull. Each appliance has had problems. Where is consumer protection? Appliances should not breakdown after a couple of years. We should not have to buy insurance policies that are expensive to protect appliances that should last at least ten years without problems. Someone needs to step in and help the consumer. I didnt call Maytag regarding the microwave as I was told it was useless to call them and all I would get would be aggravation. Someone, please help the consumer!

Bought a Maytag Bravo washer, suppose to be the best of its kind from Home Depot. Should of known I was in trouble when it took them over four months to deliver it. It lasted two years before the bearing went on the machine. Whirlpool/Maytag was of no help. Ironically, the machine Im using today is my old Maytag I bought 17 years ago. The repair cost for the new machine was about 50% of the cost of the machine purchase.

My Maytag Series 300 Dishwasher would not start. I read the reviews and took the door off (easy if you have the right tool), removed the control panel box (one screw), and cleaned the ribbon with electronic cleaner as per someones suggestion. It started right up. This is a bad design. Would I buy another Maytag? - No way! We will see how long this lasts. There is no seal on the door to keep out humidity. Do we really need a new control panel? When this is done...I am done with Maytag!

I have a Maytag Precision double oven 850 series. The upper oven handle does not fit snugly and has been broken 4 times. I have had to order 4 new handles because the hardware does not seem to secure the handle to the oven door. There are no problems with the lower oven door.

I bought a Maytag washer in Sept. 2018 because the company had a reputation of making quality products that did not need repairs. I was wrong. Because I live alone so at most I washed two loads a week, so the company cannot say it had been overused. After a little more than a year I notice at times the wash cycle took too long. One time I tried the 2 rinse cycle and it would not quit washing. A repairman reset the computer to factory settings (he was at the house repairing a refrigerator) and it worked for a few months trouble free before dying. I will not purchase another Whirlpool product since the company did not stand by its product.

Does a good job. The only thing it has problems with is frying pans, but no dishwasher can do those. 4 cycles, option to turn off heated dry. Standard size. Fit the cabinet perfectly. Just a plain white front, which is fine, but it did not get 5 stars because the white plastic control panel seems to catch and show dirt easily compared to the white painted metal door. Ive had this machine 15 years and the only repair needed was replacement of one of the rollers on the lower dish rack.

Purchased a Maytag Bravos top load washer and dryer in May of 2011. We had our other Maytag washer and dryer for 14 years, and they were working fine when we sold them. We saved a year for a new one. We spent $1,700.00 for them both. We assumed they would last as long as our old ones. Been buying Maytag our whole lives. Besides the clothes not getting cleaned. Besides the washer smelling, even after we clean it regularly with the product proposed. Besides it not working on the normal function. Besides it shredding our clothes if you put it on the highest spin speed. It started to make a very loud noise. Like an airplane taking off. Called a friend of ours that use to have an appliance store in Fenton, Michigan for decades. He said it was the bearings and that You have to replace the whole tub. A $300-$400 fix. And that it would do the same thing again in a short period of time. He said that they are junk.We would be better off buying a new one. He said, The ONLY one you can buy now that will last like they use to is Speed Queen. I had never heard of them. They start at about $750. But they are worth it. He said that they dont make any washers to last more than 3-4 years anymore. We will NEVER buy Maytag again. And Sears wouldnt give us the time of day. Each time we called and asked to be switched over to the recall department, we just got a busy signal, then a fax machine noise. We have shopped at Sears for years. Boy, loyalty doesnt mean anything in this day and age. Im sure Speed Queen will be happy to help us out. DO NOT buy any Maytag products. There should be a class action suit against them for this. There are thousands of us that got ripped off. I cant tell you how upset my husband and I are about this. We are retired, and on a fixed income, and I am disabled. The stress this has caused cannot be put into words.

A refrigerator has to keep your food at constant temperature. The first Maytag refrigerator I purchased from Home Depot could not get cold. I mean the refrigerator never got below 65 degrees. I called Maytag and they played dumb. Just wait weeks for a repairman to check a brand new product that is not working. Home Depot replaced it in few days with another refrigerator of the same model. It runs but doesnt get really cold (it only has a fan in the freezer and the air comes down from the freezer to cool the refrigerator). I live with it because all you will get out of Maytag/Whirlpool is to turn the dial to a colder temp. A little over a year passes and the fan in the freezer just stops running. I called a local certified service person. He looks at the fan and says that its running but barely. I had to replace the motor at cost with labor of around 200 dollars. I kept the motor. Turns out the motor is made by Panasonic. The current replacement motor is made in Mexico. Now the refrigerator runs cold. Since I had two of these refrigerators that failed to get/stay cold, I think they got a bad batch of motors. Maytag response was to refuse to pay a dime, it is outside of the warranty - even though I had called about the refrigerator not getting real cold on the second refrigerator. So basically I lived with food being kept at a way too high of temp causing spoilage for a year and Maytag/Whirlpool could care less, they are only worried about their bottom line.That is not the only problem with their product. The drain pan grows a mold that looks like pudding. The only way to clean it is to pull the refrigerator out, take off the motor area cover (which is really cheap cardboard) and clean it out with a rag. There is no way to remove the pan. The compressor is mounted so low that it heats up the floor. I have concrete floors thus I have no fire risk but if you have wood floors, I would check the heat level. It is nearly impossible to clean the dust off the fins on the refrigerator coolant lines. The back of the freezer door shelves are metal and very sharp on the back. Thus if you stick your hand in to pick something up, you will get a nasty cut.I have owned only Maytag, Whirlpool and Amana products my entire life. I will never purchase their products again. They may pretend that you are buying an American product (they use the American flag) but this product is nothing but OEM garbage made by the lowest bidder. They try to sell you an extended warranty for around 300 bucks for an addition 3 years. I figured if the fridge went bad after 3 years, I would just buy a new one. I never expected a motor to fail less than a year (I would say it started going bad about 6 months into ownership as started making ice at a lower rate). Maytag refuses to stand behind their products. When I told them I had the motor that failed, they had no interest in even looking at it. Do not waste your money on their products. I also own a Maytag washer that is the worst washer I have ever owned.

Purchase date of Maytag dishwasher 12/9/11 for $651.37. Controls broke 6/2013. Used Maytag specified repair service at cost of $450. New control panel installed 7/9/13. Control panel broke again 8/13/14. WILL BUY NEW DISHWASHER. NOT MAYTAG.

The washer has been inconsistent and had required five warranty visits. The computer that runs it has often malfunctioned requiring frequent restarts by unplugging the machine. Stay away.

In order for the machine not to break you have to disassemble the drum agitator during normal use... Very poor design. Mine lasted just over two years. My initial cost was $570... Dont waste your money.

This Bravos 300 washer has never cleaned clothes adequately. I have 3 sons who are athletic and this washer does not clean sweaty or dirty clothes even with extra rinse. Now my machine is 4 years and 3 months old and it needs a new bearing which will cost me $385. The repairman said this is a common repair in this machine. Maytag should be ashamed of the poor quality of this machine. I am now looking to by a new traditional top loader. These HE machines are a joke. I am contacting them to make a complaint and see if anything can be done.

I have owned three different Maytag washer/dryer sets. The reason for so many? Selling the set with the house upon moving. I kept my last set which is Bravo. I love Maytag for their features, their dependability, their reputation. I have never had repairs on any of them. Totally awesome! My second set had a neat feature of a drying rack where you could place a sweater or shoes and no tumbling. Sorry I sold that set w/ the house. I am very pleased w/ my present set of Bravo. No agitator. A coworker also bought this set. Maytag is the best!

Maytag Bravos MVWB725BW - Purchased this washer last year and have been very unhappy with the way it washes. It is extremely harsh in the way the agitator moves the clothes. Because it has a low water level the clothes take quite a beating in the washing process. This is confirmed when I remove the clothes from the dryer and proceed to clean the lint filter. The filter is constantly full of lint, even after drying clothes that have been washed numerous times before. Additionally, the clothes, even though being put in evenly, end up bunching together.

We purchased a new Maytag Bravos X washer and dryer from Lowes in June of 2013. After a year and a half of normal use (2 people in the household) the washer needs a new gearbox bearing at a repair cost of $529.00. I called Maytag and spoke to a customer service representative who informed me that there was nothing they could do about it because it was past the one year warranty. I asked to speak with a supervisor who told me they would offer me a 50% discount on the bearing but would not pay for the repair work (the cost of the bearing is approximately $25).Needless to say I will not be having the washer repaired. We will be purchasing a new washer and it WILL NOT be a Maytag, Whirlpool or any other brand made by that company. Its just appalling to think a company like Maytag can scam customers the way they do by producing appliances that are of such poor quality and then offer third rate customer service on top of it. Maytags answer to the whole issue is selling everyone an extended warranty which we all know is as bogus as the companys integrity!!!

Maytags reputation for quality is gone. Our Neptune washer has had mold, door lock seized up and wouldnt open, and now our dryer drum is cracked. Exaggerating your products reliability is one thing - this borders on corporate fraud.

I cook a lot so we wanted to purchase a double oven. We purchased this double oven about 10 months ago. Every day I complain about this range. It cooks very uneven. Called Maytag and they sent out a repairman who said I needed to preheat the oven for 25 minutes before putting my food inside. Dont pay any attention to the beep, because when it says it has preheated but it really hasnt. To think you pay that kind of money for such a piece of JUNK!! Also, I have owned 2 other glass top stoves (the last one I owned for 23 years) and never had a scratch on the surface. Theres already a big scratch on this new one. Glass top on this one is such poor quality. Would not recommend to my worst enemy.

So sad, purchased brand new Maytag washer and dryer, Commercial technology (MVWB766FW) labels. Looked and appeared impressive. Machines cost almost $1,000 each. Had twenty year old machines that still worked, I didn’t want to face a unexpected breakdown and decided to replace. What a mistake. I’m 67 and all my life from grandma through my mother Maytag was the best, not anymore. Once my equipment was installed I washed a load checking frequently, noticed almost no water in the huge tub and my clothes being beat by the agitator but not enough water to move the clothes. I tried to change to high water setting but had to cancel this load to do so. Once on high water setting I started the load again, water still very low and agitator just rubbing the clothes directly next to it, no movement of the clothes at all. Ran completely through the wash cycle but when moving to the dryer noticed some light blue shorts had dry spots, many, which had never been wet even through the wash, rinse, and spin cycles. Had a warranty service call and was told this is how the machines work. I told the serviceman had I known that I would have never bought the machines. He told me the salesman should have explained this to me which he did not. The only way I can wash my clothes in the new, expensive machine is on bedding cycle with high water setting on. Sad day when American companies can legally sell such crap. Also, called the company where I purchased and ask about return. To that I was told once I made the purchase they were mine and Reid’s Appliance in Santa Barbara didn’t take returns. Reid’s Appliance can’t be trusted. Buyer Beware, this stuff is junk. I will be throwing these machines out soon as they aren’t even sale-able on the used market. MAYTAG RIPPED ME OFF.

This is a dishwasher purchased at Home Depot on March 25, 2012 for a rental unit... call from tenant said the dishwasher did not work. Repair person from Appliance Hospital went out today and said the control panel is out and the touch pad. Cost is over $500 to replace. I will have to replace this dishwasher BUT NOT WITH ANOTHER MAYTAG.

I had a Maytag washing machine replaced under warranty back in 2011 via Maytags Extended Service Plan. This took me several months to get done because of back and forth issues with Maytag not wanting to honor the replacement. Executive Support had to get involved after I wrote a complaint on this site. When they replaced this, they sent me forms to extend my warranty, which I did. They never changed the model or serial number so Ive been paying for 2 years now for an extended warranty on a machine I do not own.The new washer broke and I called in for service on 11/18/13. Active Appliance was sent out, said it was an easy fix but they needed to order a part. On 11/20/13 they contacted me to tell me I needed to speak to Maytag because my Model/Serial didnt match with my warranty records. I double-checked these and called Maytag Extended Service and was told that I would need to speak to sales at 866-730-6094. I spoke to someone named Lindsey there who told me that I would need to send a letter in to cancel my policy and request a refund for the 2 years Id been paying for a non-existent unit and that they could start a new policy for me and get a service order in without issue. My call was disconnected during this and when I called back, I was told to call back in the morning to get back to Lindsey because the office was closing and they couldnt do callbacks.I called back on 11/21/13 and spoke to Sam who verified that the letter was needed to cancel and refund but that I would have to pay for the repair to the washer myself and theyd tack on the cost of the new warranty onto that bill so Id be covered AFTER THE FACT. Because the unit wasnt covered under warranty, Id have to cover the costs myself and it had been MY responsibility, not theirs, to make sure that the correct model/serial was on the coverage.Maytag sent me the forms and I would expect them to have added the new information on it...not send me forms with my original washing machine information. Especially as this had been escalated to Executive Support and the person I dealt with there had gone over everything to make sure it all got handled in a satisfactory matter. So for now, Im waiting for a callback from the original rep, Lindsey, but Maytag tends to Stonewall and not return calls so Im dreading how long this entire process is going to take and cost.

Maytag french door 2015 refrigerator. Not happy at all. Freezer gets rim frost on sides of pull drawers and the smell is like dirty socks when motor is running! The whole kitchen stinks???

I have a bottom freezer Maytag refrigerator that is about 4 years old. It started leaking and continued to get worse fast... It appears that the gasket around the freezer drawer does not seal about half way up. It causes a sheet of ice inside the freezer, so I am not sure if it leaks due to the ice defrosting. The refrigerator doors do not seem as if they shut tight either. After reading many of these comments about Maytag refrigerators, I am not sure at this point if it might be better to buy a new one rather than fix this one??? I looked for a recall and do not see one. Clearly this is a defective appliance.

We purchased a full house of Maytag appliances to support American Made (ourselves). It is very disappointing that our Maytag dishwasher Model # MBD 89595BW3 has completely quit functioning properly. All the lights came on and nothing worked after that. We contacted Maytag and was told to turn off the power and restart after 2 minutes which did absolutely nothing. No problem - try again. Again, nothing. The disappointment is compounded by the fact that this dishwasher is only 2 years 7 months old. It is too bad that an American Made product didnt last long enough to show any wear and tear. Investigation to repair resulted in cost prohibitive investment. So sorry Maytag, we gave it a shot. Moving on to a more reliable rated brand.

We purchased at Home Depot on 5/12/2012 a Maytag dishwasher model MDBH979SAM. The following November it started not working correctly. We had to fiddle with the cancel button to get it to work at all. It just kept on getting worst to where it would not function at all. We called Maytag service. They set up a service call with a local warranty service provider who ordered a control board and a week later came and installed. No charges at this point. Now, here at the end of August 2013, out of warranty, it is doing the same thing! I just called Maytag customer service in Tennessee and was told they are so sorry but would sell me a one year service contract. This I immediately refused. I told the person I was talking to that I had seen this website and was aware that hundreds were having the same issues and that I knew first hand that they were doing nothing about it! I informed this person I will be in contact with my home states Attorney General’s Office Consumer Fraud Division and would ask for any assistance from them available. This person then offered to replace the part at no charge, but I would have to pay for the service people to come and determine the problem (real hard to figure out that it is the control board again, same as everyone else) and then pay to have them come and install it after they order and receive it! The service order left by the tech when he replaced the first board showed a $74 fee that was covered by the warranty. So from this I have determined that it will end up costing me $150 for this repair. I also realize this repair may last six months to a year if I am lucky! Needless to say I refused this last offer too. I will have to wait to hear from our Attorney Generals office. How can any reputable business do this?

I will never buy another Maytag product, and moreover, will tell everyone I possibly can, not to do so either. Like many others, I have a two-year-old dishwasher that needs a control board already, and from what Ive read this wont be the first time. It would cost $150 for the part, plus the service calls make it around a $350 experience. The only choice is to pull the machine out, or buy a 5-year warranty for another $318.56. Grand total for your marvelous high quality Maytag that lasts only 7 years? Around $1,000. I am so sad, the company used to symbolize quality but now when I see the logo, I think of landfills.

A year or so after purchasing our new home, we purchased new appliances. We thought Maytag was a good company to go with. We had serious issues with our 2005 Maytag bottom-drawer freezer refrigerator right off the bat. It arrived with a large dent in the door. They offered to take $50.00 off the price. We insisted on one without a dent. They replaced the refrigerator, and shortly after, the board and the ice-maker went out right away.Although the parts were under warranty, we had to pay for the labor. The refrigerator is 6 years old and now it is making a constant knocking sound. We paid a lot of money for what we thought was a quality appliance. What a joke. We had also bought a new Maytag washer and dryer set and they fell apart after 5 years. It’s the same with the Maytag dishwasher. Do not buy Maytag appliances. They are cheap. They fall apart. The customer service is poor. I feel cheated.

We bought a new Maytag Bravo series thinking we were buying the best product... not! The washer has been running great. But when it came time to clean the washer on the Affresh cycle, the washer overflowed. It turns out the washer fills up higher on the Affresh cycle than it does on the regular wash cycles. Well, that’s why it overflowed; the plastic tub that hold the water had a freaking crack in it near the top! This washer isnt even 3 months old. I had to get a repairman in here once to check it out, then again to come back and fix it. At least it was under warranty. Im afraid what else will happen. Piece of crap Maytag, great quality checks! Maybe hire some real people that can see what the hell they are doing in quality. I told them about the damages to my basement. They sent me paperwork to fill out. Forget it, the paperwork gives you the runaround!

Two years old, single person owned and will not operate - At 2:00 am, April 25th, 2012; I went to take a load of laundry out of the washer. It was still full of water and would not operate. I am a single person. I do not do load after load in two years. In fact, I was doing a weekly load of clothing, nothing large. I paid close to $1,000.00 for this unit. This sucks and why only one year warranty? Are you Maytag? A Youigo car would run better than this. And they are built cheap.

Gemini Twin natural gas range - I bought this range approximately 18 months ago. I thought it had all the features I needed and it looked good -- looking good is just about all it does! If you are a real cook I would suggest you avoid this range. The burner controls are preset and it is impossible to turn the flame very low if a simmering heat is required. If you are making meringues, again, the oven heat cannot be turned to a cool enough temperature. Ovens bake/broil unevenly. It takes forever to bring a pot of water to a boil, not because the flame is not hot enough, but because the pots sit far too high above the flame. Bad, bad design. Probably designed by someone who eats take-out!!

Called serviceman to tell him the washer leaked and he said it was my fault because the door wasnt wiped properly. (There was no visible dirt because I wiped the door each time as per his instructions.) Never got it resolved. After much arguing, I gave up. Then, after the warranty, it started tearing our clothes apart. Maytag says, Nothing we can do, warranty is over. We can find you a service person other than the one who sold it to you but you have to pay. So many ruined clothes. Now I read lots of reviews with the same and worse complaints from others. They sure have gotten away with making garbage.

What was shown on tv and the way it looked in home depot were much different when I got it home. The refrig. Is big as a bo car on the outside but inside nothing.

First things first, Maytag Bravos washers are crap. Dont buy one. Purchased model # MVWB750WQ 06/12/2010 for $872.02 + tax. After 3.25 years the spin cycle started making extremely loud whining noises. Bought a replacement water pump for about $100 as several people were reporting the same issue. Before I had a chance to replace it the washer started leaking from under the washer. And not a small amount of water! Mats were getting soaked after each wash. I went ahead and replaced the water pump. But the whining noise, while diminished, didnt go away. And the leak continued. Based on what Ive read on this and other forums it looks like Ill have to replace the bearings for the tub. Not going to happen. Just ordered a Speed Queen washer for about the same price as the Maytag and I will never buy another Maytag (or Whirlpool) product again. Note that I purchased the Maytag at Best Buy. Its important that Best Buy take some of the credit for this issue as they are complicit in keeping these substandard products on the market.

Purchased a Maytag Centennial Washer from Lowes. This is the NOISIEST WASHER I HAVE EVER HAD. Self Balancing, pretty much the way it is, YOU lift that heavy wet laundry and re-arrange to balance. It just slams around even moving the washer, until you do. This washer also doubles as a BLENDER. It SHREDS laundry. The agitator does not go all the way down and thus, clothing, towels, rugs... get stuck under the agitator, wind around and RIP. Have had hundreds of dollars worth of laundry shredded such as: shirts, towels, new rugs and it even ripped the waist off a pair of my jeans! The other laundry gets tied up on the stuck laundry and you end up with a twisted, ripped, tied up Laundry Ball. It will not wash or rinse well when it does this, naturally. Lowes: The salesman knew about all this, and sold it anyway! He had one and got rid of it. Gee thanks Lowes and Maytag, for the worst washer I have ever had the misfortune of owning.

After less than two years the commercial washer we purchased from Lowe’s died. A repairman came out after a week and said it potentially needs a new control unit or computer. The control unit is on back order and we’ve been without a washer for a total of three weeks. The situation still remains unresolved and I’m regretting not going back to Samsung. After 9 years with a Samsung washer, it died and Samsung refunded the full price of the washer. It was a poor choice to choose American. :(

I purchased Maytag washer, as it was rated the best of the best at the store. First of all, Delicates cycle washes exactly like Normal. All my sweaters got ruined as the agitation is VERY HARD. I dont think the manufacture even knows what that cycle means! Absolutely awful! Theres no difference between Delicates and any other cycle!Second, Deep fill cycle. If you select off on that cycle the clothes get hardly damp. HOW can you wash hardly damp clothes???? If you go with Deep fill, the washer is supposed to weigh your laundry 1st and ONLY pour the water according to the weight. Well.... you can put only 5 small items and the washer fills all the way to the top! What the hell is this???? How can few items fill such a ginormous washer???? It doesnt work! Im so pissed and want this washer out of my laundry room!

I bought this machine about a yr ago. My clothes come out so dirty white spots all over my clothes. Now my bills are higher. Because I cannot afford another washing machine I have to bring them to the laundromat. I saved my money a long time to buy a washer and now I am without one and still paying for this piece of tin that does not work... If I ever get a chance to buy another one it will not be a Maytag. Trust me never never never again!!!!!!!!

In October 2016 I purchased a New Maytag washer (Model# MVWC565FWO) from LOWES. I bought an extended 5 year warranty with it as well. I have my invalid, totally incapacitated Sister living with me. The situation requires several loads of washing each day due to her conditions. TWO WEEKS after starting to use it we began having issues with the washer. It would stop in the cycle, lights flashing, only way to restart is to unplug it, move control from wash cycles setting to drain and spin... then within the next 3-4 loads it would do it again. Sometimes it sat for awhile I would smell like an electronics Odor getting hot... I called Lowes. They replaced it. Approximately 3 weeks later the NEW washer began doing the SAME THING...Lowes would not replace it with a different Model or brand... only send a repairman out. Long story short, he has been here 4 times, replaced the Computer Control with NO IMPROVEMENT!!! NOW Lowes is sending him out again and saying that if this doesnt fix the problem they will refund my money... My problem with it all is this... IF MAYTAG is having these type issues, WHY PRAY TELL, has a recall or solution been found and passed on to the repair folks??? I bought this Maytag due to #1 Reputation, #2 It was Assembled in the USA, NOT South Korea like the Samsung with recalls... Now all this is going on. I WANT A WASHING MACHINE THAT WORKS RIGHT!!! This is totally unacceptable and totally uncalled for. WHY could these Govt agencies and Manufacturers not LEAVE the washers alone? Computer technology... PLTTT. The old timers controls gave no problem in over 40 years of using them. Now this crap.

Purchased new Maytag washing machine July 17, 2011. Have had several problems with it over the past three years. Most of the time it would not complete a load of laundry and would get stuck before the drain and spin cycle. Last week, the spin cycle became extremely loud. Had a repair person come out and was told the motor bearings were bad. Estimated repair cost $700. Purchased this unit new for $569.00. Called Maytag, was told that 10-year warranty on drive motor and wash basket did NOT include the bearings. Asked if they could help out with repair cost, was told no. Will never purchase another Maytag product again as they do not stand behind their products. Household has 4 people in it so use of this machine was light to medium.

So we purchased a whole package in sept 2014 for our newly constructed home. In Nov we received the CO and thats when everything was finally professionally installed. After its first wash the dishwasher broke and there was a flood in the house and soaked 20% of the newly installed high quality cabinets. We cleaned up everything and called Maytag to have someone inspect it to see what needs to be fixed. The gentleman came about a week or two later and said that the machine isnt worth fixing and to try to get Maytag to replace the whole machine, but he still listed all the parts that were needed to fix it. We tried calling Maytag and said what the repairman said but they said he must fix it and they will not provide a new one. So we wait for the parts and no one calls us. We follow up with Maytag and they say theyve ordered the wrong parts so it will take longer. We try calling the repair man and he doesnt call us back.Then call Maytag again and get them to call the repairman to see why he doesnt answer us. They told him to call us twice and every time he tells Maytag that hes called us and we dont pick up. So we tell Maytag hes lying, the repairman hasnt called us for weeks and Maytag doesnt give a **. And seems like this repairman is freaking lazy and doesnt want to work, even if hes paid for it. You know whats happening now? Chargeback! Thats right Maytag, screw you. When I do another house I will never buy Maytag again! Horrible service and a very defective product. I thought we were paying for quality!! They lost a customer that is faithful and doesnt mind paying extra. Hope everyone can take this into consideration before buying. I wish I wouldve seen these comments before...

Does a good job of cleaning but takes much longer to complete. Pretty much standard features. Has rinse only cycle, air dry only cycle, and cycle for pots and pans. Top rack had special holders for long stemmed glasses which I dont need. Standard size. Same size as my Kitchen Aid. White, front load, no special appearance. It takes much longer than my old dishwasher. Also the soap dispenser broke after 2 months and had to be replaced. It requires that two buttons have to be pushed to start. My old one only required one. It does a good job of cleaning.

I bought a brand new Maytag washer and dryer at Home Depot and did not use until a week later when I found out that the washer did not spin out the water and the machine turned off automatically when cycle was not finished. As a result my load was soaking wet. I called Maytag customer service and they sent the technician. I was standing next to the technician to see what was wrong with the washer. After checking several things and seeing the unresponsive of the washer the technician told me the control unit failed and the clutch also failed. He had to order the parts and it will take at least a week for him to come back and fix it.I called Maytag customer services and complained about the brand new washer and ask them to replace it with a new one as I dont know if the problems returns and it doesnt have just one failing part. Both the controlling unit and the clutch were failed. Also i bought a brand new products I expect it to work. I dont want to pay for brand new washer and I could not use it plus it took so much of my time going back and forth between Home Depot and Maytag. It was so stressful and I had tons of laundry that need to be done. I also had to take half a day off to call the Maytag customer services and Home Depot.During my first call with Maytag customer services I asked them to call my local Home Depot so Home Depot will allow me to exchange for another Maytag washer. They had refused at first but when I told them all the reasons above they agreed to call Home Depot and allow the replacement. They asked to hang on the phone while they were calling Home Depot and finally confirmed with me that I could go there and do the replacement.Surprisingly when I came to Home Depot they said they did not get any notes or call from Maytag regarding my PO# and the replacement. I had to wait for 1hr and 15 minutes for the Home Depot to be able to connect to Maytag customer services and we had to wait for their supervisor to approve the replacement. I was so disappointed later to hear Maytag supervisor telling Home Depot that I had to wait for the repair and they did not approve the replacement. Its really a waste of time and money to buy Maytag products and they dont honor what they said to customers. Once you pay them they take your money and dont really care whether their product is worth the money consumers spend on them. In general its a rip-off!!! Stay away from Maytag products if you dont want to waste your time and money!!

I purchased a dishwasher model #MDB4709PAM from home Depot in March 2014. There is something wrong with the electrical and it is shocking people if you touch it. Just so were clear.. MY DISHWASHER IS ELECTROCUTING PEOPLE... Called Maytag repair because hey its only five months old. Cant send anyone out for three weeks.... three. Took an hour on the phone because I had to talk to four departments. Kept asking if anyone had been hurt seriously or property damage, so they made sure their butts were covered, sigh..... Should have bought the LG.

We purchased the washer and dryer set from Lowes about 5 years ago, and purchased the extended warranty fortunately for us. We had good luck with the washer for about 6 months, then we had to call problem service out because the washer filled with water but wouldnt do anything else. It took several days for the service people to come out and when they did, they had to order parts to do the repair, so we did not have a washer for a few days or a week. They got the washer fixed and everything was good for a few months, then our dryer quit working. We were told that the tub of the dryer had come off, so they had to order another one. So we were again without a dryer. Once they got the parts in the repair company that was sent out to fix our dryer, did not fix the dryer correctly so we had to call Lowes repair service to send someone out again. We have owned this set for over 4 years and once again our dyer has gone out. During all of this time, I and my Brother had to leave our job in order to be home and meet the maintenance people to fix both washer and dryer. I would not recommend this set to anyone, this is one of the worst sets that I have owned. I thought Maytag was a brand that you never had problems with, but we have had nothing but problems with this set.

Dishwasher model: MDBH949AWW3. Gradually over a months time lost its control functions and its status display. Ten days ago the last button to fail was the start button and the dishwasher stopped working. Maytag confirmed over the phone that there was no recall on this model. The part costs $190 and is out of stock till end of October 2013. I opened the dishwasher and took a closer look at the keypad. It has the cheapest touch buttons I ever seen. Maytag had provided at purchase time a user guide and a large sheet with a sketchy incomplete drawing (W10142800C) for service use only. I made my own schematics and I built my own keypad for less than $50. You may notice that the info I have on my attached schematics is missing from Maytag/Whirlpool incomplete drawing. My keypad is working fine and will outlast all the remaining parts in that dishwasher. I wish there is an angry lawyer out there with a bad dishwasher like mine that will use this info to sue Maytag. Please give the schematics to any user having troubles with this lousy touch pad.

I called customer service to ask if there was some way that Maytag could assist me with repair of this like new dishwasher. When I said it was out of warranty and I had no additional warranty, I was told that a repairman could come out for $110 and diagnose the problem and that parts and labor would be extra. I explained that I had purchased Maytag because I saw commercials, for years, showing that Maytag repairmen had no work. She was very unhelpful and kept droning the same mantra, that a repairman could come out for the above charge. I was very angry and asked for the name and address of the President of Maytag so I could send a letter of complaint. I composed a letter, however: it is Thanksgiving time and I need my dishwasher so I made an appointment to have it repaired. I was told he would be out Mon. between 8 and 5. I asked for a more specific time and was told that I would get a call on Sat. with the time. Thankfully, no call came, because on Sunday, I read the reviews on this site and realized that Maytag was no longer a reliable nor a responsible company and I decided to save myself money and time and stress and just go out and buy a GE. So we will hand wash the dishes on Thanksgiving and buy a GE on Black Friday. This does not mean that I am letting Maytag off the hook. I intend to send my letter to Jeff Fettig at Maytag and also join in the class action suit. How very sad that the name Maytag has become just a name used to shill for defective and shoddy merchandise.

I am very pleased with the product, a perfect stove for cooking! It’s very easy to operate, easy to clean, multiple burners, excellent in cooking large meals, like soup, beef, Chicken and vegetable soup. It’s also very energy efficient, very safe to operate,

Have used for several years, no problems. Not even with ice maker. The black color is good and matches other appliances. I like the pull out drawer for freezer items. However, the filter is very hard to change but other than that everything ok.

My refrigerator outer case has felt very warm to the touch at the section between the top freezer door and the lower refrigerator door for several years. I thought this was a normal function of the defrost mode. It is now very hot to the touch so that I cannot touch it for more than a few seconds. I dont know how long it has been like this. This cannot be normal. I did some online checks and found that there was a Consumer Product Safety Commission Recall release #09-145 and 09-322 that warns about the same problem I am having. My model # (MTB215) matches the recall, however, the last two characters in my serial # is WQ does not. This problem appears to be very consistent with the problem in the recall releases.