It is impossible to dry clothes in the dryer without the worst wrinkles you can imagine. I have 2 of them and they are both horrible machines!! The drum spins too fast which causes the clothes to get stuck against the tumbler fins. The centrifugal force holds them there and they just ride around without tumbling in the drum. When the cycle is finished the clothes have been dryer while jammed up against the fins and they are so wrinkled you have to wash them again. The ONLY way to get them through a drying cycle without a tremendous amount of wrinkles is to stop the machine every 5-8 minutes and fluff the clothes around inside the drum by hand. DO NOT BUY!!

Unbeknownst to us, our Maytag Refrigerators (MFD2561KES) ice maker developed a problem with the fill hose which connects to the back of the refrigerator, causing it to pop off. The hose had been leaking water onto our wood floor causing all of the boards under the refrigerator and 6 feet in front to buckle. I cannot see why Maytag did not use a compression fitting instead of using a squeeze type hose clamp. Plus the ice maker has left a large sheet inside the freezer on the bottom. I use the ice maker daily to fill my cooler for work.We also have a Maytag Dishwasher which has a push button panel in front which has decided to give out as well. Not to mention our Maytag Double Oven which has never been able to close properly since we have had it. (The service man said that there is nothing wrong with it). We bought our house 7 years ago and my wife wanted nothing but Maytag because of our experience in the past. I gave up buying american automobiles years ago and I guess the same will happen when I replace these appliances (after I finish paying for my new floor).

Just read Ann of Colorados (posting April of 2014) message about her Maytag Bravo washing machine and its like I wrote it myself! Our Bravo started with making a loud noise during the spin cycle which turned into oil or a dark liquid spraying out from under the machine, along with saying UL, so I would adjust the load and get it going again only for it to start the spin and rinse cycle all over too! We have 5 people in our family and cannot afford to not have a working machine. We purchased this machine only a few years back to replace another product that was also a piece of junk. I guess as a last resort I will try a Spin Queen which is American made and hopefully will work! Very disappointed in Maytag. Whatever happened to Machines lasting like they did for our Grandparents?

I purchased my Maytag Bravos XL washing machine in July 2016. In August 2016 it broke for the first time. I was just passed my 30 day moneyback guarantee, so Sears would not take the washer back. I have had more than 10 service calls on this washer in one year. I live in a rural area, so Maytag told me I was in a non-serviceable area and would have to wait WEEKS until they found a repair person willing to come to me. I only live 40 miles from Richmond VA, where I purchased the washing machine, so imagine my shock when they told me they couldnt fix it because of my location! Ive had countless people in and out of my house, and it still does not work right. You can only do very small loads, so the perk of having an XL machine is none. But even at that, it does not properly clean anything, tangles clothes, and will leave even the cleanest items looking terrible when they come out.Ive had a new circuit board, new transmission, new bearings and gears, new balancing rods, and still, Im left with a machine that does not wash and makes terrible grinding noises. I bought the washer and matching dryer as a set, and even the dryer had to get a new circuit board put in it in the 1st 60 days! After thousands of dollars in repairs on a $1000 washer, Maytag will not admit I have a defective machine and replace it! I just ran a load of laundry and have to call Maytag yet again, because the grinding noise gets louder with every run. Do not waste your money!I would give anything to have the 29 year old set I gave away when I bought this garbage back! I have literally been on the phone with Maytag in tears because it doesnt work properly, Ive had to throw away items that would not come clean because there is not a laundromat available in the town I live in. All I want is to be able to keep my family in clean clothing and linens, doesnt seem like too much to ask.

The dishwasher is only one and a half years old and like many others are having trouble with the control panel. The model is MDB89495AWO which cost nearly $800. The dishwasher does not shutdown after an operating cycle. On contacting Maytag with the symptoms they advised that they have never heard of a similar problem. On reading the comments/experience of other Maytag owners I am undecided whether to scrap this unit and buy another make!

This Maytag was installed in this house in the summer of 1984 and washed dishes for my in-laws for 26 years. We moved in as a family of four and this Maytag dishwasher is still washing the dishes clean. No rinsing, just make sure the food is gone. We replaced the belt about 6 years ago and I think my Mother-in-law replaced the door seal. It has a power saver button, 2 cycles, and the cups are on the bottom rack, plates and such on the top. I dont put plastic bowls on the bottom because it gets a bit too warm for them but all the bells and whistles still work. It is a fairly large model, WU301, with ample room for plates and platters. I dont wash pots because I dont like what the dishwasher soap does to the finish on them. Having the cups on the bottom is nice and the rack is very usable for other dishes as well. The cutlery rack is located on the top rack, removable and a decent size. Almond body, silver and dark brown accents, very 1984 but not a bad look. All of the buttons and knobs are easy to read and use. Maytag, 1984, model #WU301.

My dishwasher is 9.5 months old. The computer board needs to be replaced and they cannot find the part. It’s been 2 1/2 weeks since I called in the repair which is under warranty. I was told they have 10 business days to search the country. Really search the country. Does anyone know what will happen if they cannot find the parts I need?

My Maytag washer (model number MVWC400XW3) worked well for 6 months. Suddenly, it started making terrible loud noises when spinning. Repairmen have come out 6 times, and I got second opinions. It was turned over to another repair company. Transmission has been replaced as well as the motor. I have been without a washer for 3 months. Repairmen would come out, replace a part, and leave; and the washer is never fixed. I asked the repairmen to stay for an entire cycle, but they act insulted and left, saying its fixed. When I tried to wash, everything went crazy. I unplugged the washer and plugged it back in to reset it. I turned the dial to spin, and the lights said the washer was sensing. The lights never moved off that. The washer sounded like its trying to wash, but theres a strong grinding noise. When does the repairman decide he cant fix it? My husband is insisting we go buy another washer. The washer was bought in September 2011, so its still in warranty. In addition, we bought a five-year warranty. The repairmen stay 15 minutes, plug in a new part, and leave. They dont come back for two weeks. Will we ever get this washer fixed or get a new one. How do we put pressure on Maytag to fix it or give us a new one?

Washer Model MVWC555DWO. I dont like this machine. I thought Maytag is a good brand name, but I dont think so anymore. The engineers who designed these new machines with the water level saver dont do laundry. In order to get the cloth covered with water, I have to use the bulky sheet level. I have 2 jeans and a sheet that got holes in them, because the water level was not right. I would have my old machine repaired, if I have know how my new one would do. Im stuck with this machine. I dreaming that this machine breaks down soon and I can buy a new that has a better water level. My old one had water saver level too, but did a great job with the water level.

I’ve had my electric glass top range for four years. Normal use. I set the temperature to 425 degrees to bake a potato. At the 225 degree mark, the oven bursts into flames. The fire burned itself out in about a minute. I turned the oven off and immediately went to google to see happened. I’m pissed! This stove is only four years old!

Purchased refrigerator model # MFT2976AEMOO September 2013. First repair was 1 month after purchase. From compressor to moisture build up inside fridge. 7 repairs in the first year. Customer service disgusting. They simply dont care, and do not back their products. Work time lost waiting at home for repairs. Service men come and always have to order parts, which means 2 service calls for each problem. Our service man broke one of the drawers when removing it to do a repair which meant another visit for that replacement part. Continued to have more problems when warranty was done. Just replaced my 3 year old fridge. Could not afford to keep it any longer. Have never been more disappointed with any appliance that I have bought. Will never buy MAYTAG again. Product is inferior.

For the first time I bought a new washing machine in order to have one that lasted. Bought a brand new Maytag Front Loading HE washer model MHW3505FW1. Controls stopped working and the machine turns on and off by itself. Its either a faulty control board or computer, either of which are going to be more than a $400 repair. So more than half of what we can pay for a new machine. Maytag only warranties two parts for more than a year. So in reality, its not worth the repair and I will not buy a Maytag of Whirlpool product ever again.

I will never buy another Maytag product. Our dishwasher is not even 2 years old and the control board went bad. No extended warranty was purchased because we assumed that it would last longer than 2 years when our Sears Kenmore lasted 25 years. No help from customer service. We now have to spend over $300 to get this piece of junk repaired.

Maytag washer MHW5500FW had service just a month after purchase and still a year later the washer has problems spinning using direct drive. Even a few towels are soaked when cycle is done or errors out and must be restarted. Most of the time the washer has to be cycled on spin to remove water from soaked items, not just a simple bath rug, towels, bed sheets. Almost anything has a problem spinning. Had to purchase another year of service coverage as I dont trust the washer will last. Soap dispenser needs to be diluted despite using correct soap, per service tech advice which triggers sensors to shut down. Machine looks good but not ergonomically designed without the stand as you can easily lean over the washer and turn on and off accidentally. Same goes for the matching dryer, also can easily set off the on pause and on/off button. Dryer works great other than that.

Our Maytag microwave, which we bought based on Maytags supposed quality, is nothing but a piece of junk. In two years it has had or needs repairs that nearly double the original cost! Thats ridiculous. We are done with Maytag and are not going to get suckered into their Whirlpool/KitchenAid or other brands. So long.

I bought a Maytag washer in June and its the worst washer I have ever had. It has been 15 yrs since I had to buy a washer. My last washer was a Kenmore which was great. The Maytag does not have a water control knob. It has auto sensing which is crazy. I know how much water I need to wash my clothes. The water sensing barely puts water over the top of the clothes which is not what I need. My husband works in the oil field and gets oily and dirty. The next issue is the agitator that agitates the clothes. This one is a joke. The agitator starts agitating the clothes before the water is over the clothes and then when it needs to agitate it does a poor job. I am so unhappy with my machine that I am getting rid of it and looking for an old type washer. Evidently you made this washer for white collar people who do not get dirty. This is definitely not a washer for people who have dirty laundry. I am so disappointed with Maytag. I thought this was a good brand.

We purchased this Maytag Centennial washer in 2009 (model # mvwc6esw/Wd; type 849-05; ser # cy1741855) and I have hated it ever since. I had an old 406 Maytag washer that was worth its weight in gold - repaired it as long as possible. I bought this new one because it was a Maytag and that was a mistake. The way it agitates my clothes get tangled and they never did that in the other original Maytag. We had to have it fixed not long after we got it and now every time I turn it on, it immediately starts to agitate on every cycle except hand wash, which it never did before. If I knew it agitated the way it did, I never would have got it. Good thing we bought an extended warranty for this machine. We have used it once already and it looks like we may have to use it again. I am very disappointed in this machine and your workmanship. The old machines were much better and more dependable.

This is the worse designed product. The gaskets on the door keep making mold. The end caps that hold the pantry lid keeps snapping off, had to replace them twice. It is a very elaborate and complicated installation which of course they will not cover. The water dispenser is inside the left side of the fridge and the water runs so slow, that you lose a lot of the refrigeration by the time you fill a glass.This appliance is very noisy. The customer service is sometimes nonexistent. I called on 9-16, I waited 24 min on the line and decided to hang up. The next day I tried again after 15 min they hang up on me. I tried again later got Customer service, but no they could not help me with installation of a replacement for a warrantied part that snapped off for no reason at all. I have complained while this appliance was under warranty, and after. They do not care. My advice is stay clear of Maytag refrigerator, I CERTAINLY WILL.

MVWC200BW0 - Washer starts to fill and then drains before completing the fill cycle. Contacted Maytag through the live chat on their website (cant talk to a real person on phone). Since my one year warranty had been expired 12 days I was told to contact a certified repair person. They offered no help in solving my problem. Told nothing they could do, warranty had expired. Maytag will never get my business again. Now I know why the Maytag repairman is so lonely, people have quit buying Maytags.

Bought a Maytag washer MVWC415EW in 4/2015. We dont use the washer heavily but over that time span the paint on the top cover and the side where the cover comes down has bubbled up. It looks like a bad rash but only on a washer. I think the company used inferior paint which can bubble up with the heat of the hot water during the wash cycle. I called the company but they do not cover cosmetic items on the warranty. I think since this was a flaw in the paint used they should at least replace the cover portion which would be an easy fix. Maytags are not what they use be! Last Maytag lasted 17 years with no paint problems or mechanical problems.

Bought a refrigerator from Home Depot in November 2012 for a cost of $1,647.48. In August 2013 it stops making ice day 1, stops cooling & it is running nonstop, all lights on display go out day 2. Called Home Depot & was given another number to call, called that number was told someone would be out next day to look at it. Also told my warranty would expire in November & I needed to buy another warranty. Maytag customer service was very rude. If their product was any good why do I have to pay extra for another warranty. A $1,647.48 refrigerator that only lasts 9 months, REALLY!!! Do not purchase Maytag appliances if you dont want to lose your money. Shame on Home Depot for not standing behind their merchandise. If you have a problem while warranty is in effect, Home Depot should replace product.

I have to say I am terribly disappointed in the quality of my Maytag Side by Side Fridge/freezer and my Maytag stove. Having sold Maytag commercial washers and dryers to coin laundries for over 20 years I expected better. Needless to say..... these are Whirlpool machines with Maytag name plates. Not the Maytag quality that was produced in Newton, Iowa. You can tell these are plastic machines made in Mexico. Of course you still pay for the Maytag name just not the quality. I have always tried to buy from US companies, but my next appliances will not be as Whirlpool is the only US company left with exception to very high end products.

I have had my washer and dryer for 14 months and from day one, my washer eats holes in my clothes. It is always the bottom center front of my shirts. I complained about this and was told it was my clothes. They were either old, or the type of fabric, or too much bleach, etc. etc. Everything was wrong with myclothes except the washer. I purchased a new shirt and washed it without ever had worn it, and when I took it out of the washer, it has holes in the front. NOW YOU TELL ME that is the shirt and not the washer. I have used Maytag for the past 40 years and I never had any problems with the old Maytag washers. This new Bravos is a piece of junk and I am sorry I ever purchased it. I will never buy another Maytag product.

Series 200 dishwasher wont start. Just over 1 year old. Control panel needs replacing which I found out, is a constant problem and a design flaw. Called Maytag and they would only offer 25% off new part. Why would I do that when it is just going to go bad again?

My Maytag (MER7662XQ) oven has stopped working after barely 6 months of use. I filed a warranty-repair complaint and reported the error codes shown: F1 (faulty touchpad) and F3 (faulty temp sensor). Although Maytag promptly sent a repairman, he arrived without parts and left within 5 minutes without fixing anything. He said he would order parts. Whenever they were delivered to us, by mail, we should call again to schedule another repair. But he warned he was prohibited from coming out for another 7 days. So far, Ive been without an oven for almost 3 weeks and there has been no action or information. My calls to Maytag produced nothing, except confirmation they show the repair as open since they do not actually distribute parts, and the repairman is with an outside company. A terrible product and a worse service! I would not ever buy another Maytag product and recommend that no one else does either.

Bravos X high efficiency... efficient at not cleaning your clothes, efficient at ruining clothes, sheets, towels, may be efficient at being a boat anchor. Maytag offers nothing. Have had washers last 20 years or more. Someone, or some atty. General should bring a class action suit. Horrible product. Dont buy one. DONT BUY MAYTAG/WHIRLPOOL. THEY DONT TAKE CARE OF THEIR CUSTOMERS. JUNK. That report was very fair as requested. You really dont want to know how I really feel.

I bought this dishwasher from Sears on Tuesday July 15, 2014. It was delivered on Friday July 18, 2014. On Friday July 25, 2014 two plastic clips that hold the top rack on broke, and one whole side of the top rack fell down. I called the 1-800 # in the book. Then I called the repairman they recommended. He came out on the Monday July 28, 2014. By the time he got here, the clip on the other side broke. Now the rack was hanging by one plastic clip. While waiting for these parts, the last clip broke and the rack was completely detached. So he received the parts on Friday Aug. 1, 2014. When he arrived, lo and behold, they sent the wrong parts. He had the side tracks that hold the rack, not the cheap plastic clips that attach it to the racks. So I have had my new dishwasher 14 days, and have been able to use it a total of 4 times before it failed. I am now awaiting the new parts. The parts that broke are made from a cheap thin plastic, and this is expected to hold up the entire top rack and the dishes its holding.

I have just joined the open and close the door Maytag Club. Purchased four Maytag products on Black Friday 2017 as I always trusted Maytag. Only disappointed to have my microwave (MMV4205D-4) come down with the virus (open & close door) that has plagued so many unsuspected owners. Almost made its 1st year anniversary. Now I see this has been going on for years and all they do is add different model numbers at the end. Luckily Im in the 1 year warranty and repairman coming next week. Now I question if I should take the extended warranty as I see this is going to happen again down the road. And will the extended warranty cover it? Guess the Maytag repairman isnt sitting and waiting for repair call anymore. He is being kept busy!

I have a new HE (high efficiency) washer. It takes getting used to as its a definite change from the old agitating system but I think I like it. It doesnt make much in the way of suds but everything still comes out really clean. The wash cycle is much longer than my old washer but it uses a lot less water.

Like many others, my Maytag Bravo motherboard has stopped working after about 2 years. The clothes do not get particularly clean, it is extremely noisy, and the wash cycles are excessively long. I would not recommend this appliance to anyone.

We purchased a Maytag stainless steel French door refrigerator from Home Depot in 2011. The thermostat control (a circuit board made in China) broke and was replaced in 2012 by a certified repair person. He reminded me to dust underneath regularly, which Ive done. A couple of weeks ago I noticed some darkening of my wood floor to the left of the refrigerator and so I pulled it out from the wall a bit. What I saw was that my entire floor was wet and falling apart under the left side and when I looked into the freezer, I pulled out the bottom basket and the bottom was covered in about an inch of ice.I called, posted on Facebook and was put on hold several times for as long as 20 minutes before I hung up. I called Home Depot and asked them to intervene and speak to a rep from Maytag. I have heard nothing. There is black mold in the corner of my kitchen and a soaked floor that may go way beyond. I googled the leak and apparently this is very common with Maytag French Door refrigerators. I have a meeting with an attorney. Getting through to Maytag is seemingly impossible unless you have hours to wait on the phone. We have been getting sick for months and not knowing the cause.

At first my dishwasher worked great and I have always been really good about rinsing my dishes before I put them in. Starting a few months back I noticed my dishes were coming out gritty then all of a sudden it started backing up into our sink.

I purchased a Maytag gas range about five years ago. After about two months, I noticed that the paint on the burner grates was flaking off. I called the company and they told me it was cosmetic. I have since bought two sets of replacement grates. I call the newest ones my dress grates, which I put on the stove when I am having company. I use the damaged ones for everyday cooking. Last year, the panel flashed. It locks constantly. And often, the door would not open, unless we pulled the stove away from the wall, unplugged it, and that cleared the computer. So, after months of unsuccessful door openings, the handle finally fell off completely. And the door locks whenever the oven is turned on. You have to finish your cooking, press cancel, and wait until the oven cools off, and then it will unlock. I have tried pushing aluminum foil into the latch hole on the door but have not been successful. Sometimes I just put a spoon in the door to keep it ajar while cooking. This cant be energy efficient. Of course, it is out of warranty. I saw a similar complaint about the burner grates. Also, the paint has chipped in several places on the cook top and the disks are all chipped. I am never ever going to buy a Maytag product. Oh, by the way, I called a repairman. I paid $65 for him to tell me that to replace the lock mechanism and the door handle, it would be $400. I can buy a new stove for that, but not a Maytag.

We have had this refrigerator (Maytag Side By Side Refrigerator with Ice Dispenser 27 CU) for 5 years this month and have already had to have it serviced once and now the ice dispenser just went out. I wish there was a brand out there that did not have problems and when problems occur, you do not get the runaround to get them fixed!

I bought a Maytag washer and dryer unit from Lowes 3 years ago. The idler pulley failed causing a squealing noise every time we turned it on. It had to be replaced along with a new belt. The washer failed to work shortly after that. It had error codes that Maytag could not give me information about. These were both higher grade commercial units. We hoped they would last longer than 3 years without having major repairs. We also have had to install two lid switches for the washer in that same time span. Quality has been very poor and customer service has been worse. I will never buy another one of their products again.

Maytag HE Top Load Washer - We bought our whole house lot of Maytag appliances 6 months prior to when we would need them, in Nov of 2015. There was a great Canadian Black Friday sale event special, so we purchased the whole lot at Home Depot thinking we had got a great deal, however back then there were very little reviews on the washers, as they were fairly new. This is the absolute worst washer, I have to pause the washer after the water level that the sensor allows finishes and add at least a bucket more of water to cover the clothes and clean them properly and rinse them twice to make sure the residue from the soap gets washed off (I use HE pods, so not using too much soap). Certainly not what you would expect when you buy a high-end appliance. Im going to replace it, but I cannot even try to recoup any money back, as I couldnt/ wouldnt be able to sell it to anyone knowing that it is just garbage!! You would think that a high-end appliance company like Maytag would admit that this appliance is a mistake and offer the consumers that purchased this junk a credit towards a washer that will do what is expected!! Think about it Maytag... you have lost a lot of future business by ignoring the fact that this machine is not what you advertise as a company that stands behind their name. I am sure to tell everyone that I know about the disappointment in this product. I have a friend that has a LG HE washer and it works great... so no excuses about water consumption regulations... its just not designed properly!!

We purchased this washer from Sears. Its always been loud during spin, but the past couple months it has gotten VERY loud. It jumps around. Also, it tends to ball clothing and towels. It has been hard on my clothes and bedding. Many times I have to rewash towels and bedding, even jeans at times. I have been very unhappy with this purchase from day 1. It was not a cheap washer.

Fifteen months after purchase of the top load washer, we have had to call in repair. The lid lock and sensor have went out on the machine and the repair costs are equal to the purchase of the machine. Whether the consumer has an extended warranty or not, this is unreasonable. So hear this Maytag, the CONSUMERS will invest elsewhere when delivered cheap merchandise like this even if it is Made in the USA as you wish to tout in order to bait the consumer for their money instead of providing superior quality American products. This consumer is sending this machine out the door.

After reading all the reviews I realize this is a wide spread complaint. After 2 1/2 years the control panel on my Maytag Dishwasher will not work. You press the keys and hope for the best. I am thinking of going to the media with my complaint. Maybe we will all get some sort of refund or upgrade.

I really like the refrigerator. Its easy to maneuver and frost-free, but I should have gotten the side by side. Also, make sure of your family size before you make final decision. Other than the size I would recommend to family and friends to purchase.

Electric stove range is great. It was very affordable, this stove is very easy to clean and wipe down on the outside. I had it for 4 years and had no problem with it. Would definitely recommend it to anyone on a budget. It also has a warranty which is also a plus.

I have a dishwasher that would randomly leave chunks of food on dishes, above and beyond not working and would take entirely too long to clean the dishes. This silly thing would run for hours but still produce dishes that were clumped with food. The local Maytag could have cared less. They said that it was the wrong detergent or hard water or we have not pre-cleaned enough. I am taking the old dishwasher to the range for proper disposal as a backstop, and buying something not made by imbeciles.

Constantly does not clean clothes, always out of balance, codes constantly come up, only 2 1/2 years old and already rusting out. No matter what you do this washer does not want to work. Has special cycles for bulky loads but try to wash 7 towels and it will dance all over floor then shut down with an unbalanced code and you have to unplug to reset then wash towels again but not use spin and have to wring out towels by hand. I cannot believe the Maytag company has not recalled this very expensive pile of junk, and their service department is very rude and not helpful at all.Also as soon as you call an appliance repair company and tell them its a Maytag Bravos they say we do not fix those, do yourself a favor and junk it and buy any other brand. I have 3 kids now grown so we have bought about 5 washers over the years and when we saw that this was supposed to save water and energy and do bigger loads we were sold. Big mistake! Whatever you do never buy any appliance from Maytag. Products are garbage, service is nonexistent, and the cost will make you boil.

After 15 months of use the Maytag Dishwasher MDB8959SBS2 the control panel start malfunction. I read very carefully about the Home Depot Customer reports before purchasing this built in stainless steel dishwasher, and supposed to be one of the top notch on the market, around $850 retail price. It becomes a big disappointment. After three months of use, the top rack handle broken but it still under manufacture warranty, so we get it fixed by Maytag contractor. Then 15 months after regular use for a family of five, the control panel start malfunction, few bottoms will not start anymore. We are out of luck with one year manufacture warranty and working towards our VISA card extended warranty to try to get it fixed.

Works great, quiet, cleans better than the others in my opinion, have had many others and they never impressed me like this brand does! I think this one gives you your money's worth and you don't have to look no further for a dishwasher again, and is top quality and hardly breaks down as well.

My Maytag washing machine is rusting out at less than three years! [Photos included]. I have called customer service twice, spoken to two different women and have been told that it is a cosmetic issue [Model MTW2541240; Serial CW2541240 ]. The last e-mail with photos was sent to Gwendolyn **. I indicated that the rust has ruined very expensive sheets, other clothing, towels. It took me a long time to figure out what was causing the spots on the clothes. There is rust on the outside of the machine, the lid and inside the actual drum which holds the water. The machine is a lemon. You have me registered in your system with the date of purchase.My question to you, since when is rust in the inside of a washing machine a cosmetic issue? Are you aware of this issue? Do you as the CEO believe this is what is acceptable for a Maytag washing machine? I firmly suspect this issue is beyond my washer based on my research with various stores and sales people. They are telling me I am not the first with this issue, non-Lowes stores. I purchased the machine at Lowes and because no one at Whirlpool was responsive to him or to Lowes, he is offering to apply the refund to a new Lowes washing machine. I am now in the process of searching my credit card records from Sept-Oct 2008 which is when I bought the machine.I would like not to be restricted to Lowes for another washing machine. I will notify Rick ** (at the Lowes Turtle Creek, Coconut Creek store in Florida, telephone 954 346-3993) of this letter to you so that you and Rick dont think I am trying to obtain a double refund. I just want the full value of the washer back so that I will have a choice in the replacement. The selection at Lowes is limiting. I will upgrade to more of a commercial washer and pay the difference. I wanted you to be made aware of this issue.

Maytag Bravos MCT washer not good - Owned this since June 2017. This thing has never worked properly. Every time after a cycle is complete we have to wring the soaked clothes by hand. Even after doing this the drying time ends up being double what it should be because the clothes are so wet. Not only time wasted on hand wringing clothes but also wasted energy in drying them afterwards. Also this thing is supposed to auto-detect how much water it should use but half of the time it uses too little water and doesn’t actually wash all of the clothes. Some clothes stay totally dry when this happens.

Whos up for a class action lawsuit against Maytag? I believe Maytag is making claims that are NOT true. I bought a new Maytag Bravos XL in Nov 2015. I asked the salesperson to point me to a deep water washing machine for Large loads. Salesperson sold me the Maytag Bravos XL MCT and made claims I would have 30% more water than the other washers. The sales pitch (according to Manufacture) is these smart machines have sensors that can detect how much water is needed. THIS IS NOT TRUE. My Maytag machine only gives me 1-2 inches of water on the normal and rinse cycles and maybe 4-5 inches on deep water cycle!!! Certainly not enough to cover clothes, towels or sheets. I immediately called Sears. Tech is basically being trained to tell consumers thats the way it is. This is the new future in washing machines. So, My recommendation - hire an attorney to get your money back!

Had some extra time, so I thought Id add my .02 to those including myself disgusted with Maytag products! 1st up, the Maytag washer and dryer I purchased from my nephew after his divorce. The washer shot craps 2 months after I bought it from him (out of warranty of course!). The transmission went out - cost to repair $550.00. My nephew paid $350.00 new at Sears. We happened to have our ol reliable clanking GE, so we used that while deciding what to do about the washer. In the meantime, the dryer quit heating. Cost to replace heating element - 400 smackers! Dryer new at Sears was $250.00.Come to find out that even though they had Maytag names on the washer/dryer, they were cheap copies by White/Westinghouse. Well anyway we bought a set of Whirlpool Duets before doing our homework, cuz if we knew what was gonna happen... Before we knew the trouble we were going to have with the washer/dryer, we got a Maytag Quiet Series 300 dishwasher (Maytag Quiet Series 300 MDBTT60AWW). Yip, the control panel failing problem! Only purchased 1 so far (only 1?!), but my wife likes to hand wash the dishes. If we were the typical family using the dishwasher all the time, I would have replaced more than 1 at a cost of $135.00 each from Sears and doing my own R&R work, saving on the labor. Cost new at Lowes - $350.00Up next is the Maytag fridge. I purchased it back when our 2 boys were at home. I bought it mainly for the name and large capacity. After about a year (yip out of warranty) the cooling was very uneven. Sometimes the freezer would defrost by itself, then it would start working ok again. The top couple of racks in the fridge would be quite a bit warmer than the bottom. I understood the top racks would be a little warmer, but Im talking like 15 degrees. I called a repairman and told him about the problem. He said hes received numerous complaints on this particular fridge, and theres really no way to repair it unless the electronics are replaced as well as the compressor because as the compressor gets weak over time, the electronics get fouled up by this. Cost new - $1300.00. Estimate over the phone cost to repair - $950.00 with no guarantees. Replaced with a SamsungAs far as the Duets? No problems so far. They work great and we are very pleased by them. But I have did my research and am holding my breath! I also have a Maytag microwave thats still working, but has did a couple of unusual things - the lights in the front panel display started flashing showing a fault. I unplugged it when its did this to reset it. That was a while back and now it seems ok. At least for now!When someone says, Yeah, well, you might just have a lemon, but the rest of Maytags appliances are fantastic! My wife and I when we hear this are ready for a fight! Weve had experience with all of Maytags products, and with the exception of the Duets (so far), they are nothing but junk!! Another thing I wish to mention is the Samsung fridge. Its about the only model that has a factory 5-year warranty on the compressor and major components. Weve had several fridges in our married life, and the Samsung is far superior to any fridge weve owned. Ill be looking to that brand in the future. The last item I promise: If you read the reviews on front load washers, none of them get very good ratings. If I would have know that, I may have purchased a top load. But the Duet washer does do a superior job (IMO) cleaning the clothes, and the clothes are virtually dry after the last spin.

WE bought all new Maytag kitchen appliances and the extended best service contract. Cost 1/2 of the cost of the appliances. This was 3 years ago. Recently dishwasher went blank. Service call was a factory neutral wire. Then ice maker replaced with a reman unit. Then we thought something was wrong with the oven cleaning system aqua lift. So after many hours and calls two service techs told us the system will not clean the oven and after many cycles it will not and the bad part is they are still selling this system to the public. Criminal. I think they should own up to the public when they do this kind of thing. On top of this I would go buy the self cleaning oven but the tech even said he will not use it because it will break and need replacement. It is no better other than you can use oven cleaner to clean the finish without the heating element and you cannot use anything that works on the aqua lift finish. Bad deal.

We purchased a Maytag front load washer in May 2006 (MAH6700AWW). In November 2012 we had a leak and called a repair service. We were told it was the dispensing hose which had a hole worn in it and was replaced. In February 2014, we called the same service and was told that we had the same problem. Now in November 2014 we are experiencing the same problem. We have notified Whirlpool of this problem and each time were told that the machine was too old to reimburse us in any way. Guess who wont be buying any Whirlpool products if they do not back up their faulty workmanship.

Product: Maytag MFI2665XEM Ice2O 25.5. Bought this refrigerator on Feb. 2013 at Home Depot. Maytag cannot repair the heat exchanger as it is a discontinued model. Our only option: Purchase another comparable current model refrigerator with a full price of $2,199.00. It will be sold to us for a discount price of $1,308.00 with free delivery. NJ tax and installation not included. This is a two year old refrigerator with orig over $2000. We had requested for a repair since August 2015. We had spoiled food expenses and rented a temporary refrigerator. Numerous attempts to repair and order the parts to no avail. The excuse is either they ordered the wrong part and eventually was told its been discontinued. Our warranty was automatically canceled. We have spent numerous hours with the Maytag customer service and was given a promise to find the part overseas as well to get the appliance fixed. Finally, this morning of November 2, 2015, we were given the final Im sorry and this is all we can offer you, to buy another refrigerator from us. It appears that this is a defective model but we have not received any recall letters or warning about it. This needs to be addressed as this is an unacceptable practice and deceiving to the consumers, and certainly unfair for people like us who work very hard to pay for this appliances. We cannot afford another $1500 refrigerator. We are now stuck with this worthless, stainless steel junk in our kitchen.

I have a Bravos washer model # mvwb45owqo and matching dryer. The price for the pair was $1347.00 plus tax. The washer and dryer were bought Jan 14 2010. 10-10-13 the pump went bad and was replaced. I paid $ 221.00 to have it replaced. 10-31-2013 I was washing a load of cloths and it was very noisy. I call the local dealer and they come out and said that it needs a drive shaft tub part #w10193886. I would be about $300.00 to replace the part. Also they charge $75.00 for a service call. I called Maytag and talked to Ashley (**) from customer service and she said they could not give me any help that the washer was too old. I might also add that my last washer was 3 years old and the motor needed to be replaced. It was also a Maytag. I always thought if you paid more money for quality it was worth it. I am sorry I did not buy a cheap machine from Sears or somewhere else. It would of been 1/2 of the cost and I could of replaced it after 3 years or so if necessary and still been money ahead. We also have 4 rental homes that have all Maytag in it. I will be holding my breath that they are not junk also. I will tell everyone I know not to buy Maytag and I will never own anything that has the Maytag name on it again.

Re: refrigerator model # MBF2258XEB1. The above-referenced refrigerator was purchased in 2011 from Home Depot. We paid over $1,000.00 thinking we were buying a good product. Right now the bottom freezer is working but the refrigerator is not cooling. An appliance repairman cleaned out the defroster part, but that did not resolve the problem. He said it was a compressor/valve gas line problem. I cannot afford to spend hundreds of dollars to have this repaired. Even though the warranty has expired, I believe that Maytag should pay the cost of the repair. This is VERY inconvenient and frustrating.

There was a maytag dishwasher in the house we bought 11 yrs ago. The only problem we have had is a recall on the rinse aid dispenser which was replaced by a service man but never worked again. We are completely satisfied with the operation of the unit, our only disappointment is the wire racks. The original racks plastic coating broke at the end nubs and became rusty and swollen. We found someone selling a unit and we just took the racks and left the unit for him to resell rackless. Unfortunately not two yrs later the same thing has happened to those racks. Even tried these little plastic covers that are made specifically for this problem. They were virtually impossible to get on and didn’t last more than a few months.

M1BXXLZYB00 - This is the worst appliance I have ever owned and I am 56 years old. Very noisy, freezes my produce and actually anything in the refrigerator. Yet the freezer wont freeze popsicles. Had 2 service calls on the fan and or fan motor in the first 6 months. Now 2 years later we have replaced 2 compressors and had to pay 200.00 labor to have installed. Now the compressor is out again not even 30 days after the first 2. Whirlpool wants to send another compressor and the poor repair guys are suppose to do it for free now because it is within the 30days. The offered me to buy another refrigerator with prices of 699.00 and 519.00. My fridge in the garage is way more dependable than this one and I have had for 10 plus years with no problem.

I bought a new smart washer and dryer from Maytag in mid-2019. Beginning in the first few weeks the machine did not perform as expected--cut off in middle of cycle, door failed to unlock at end of a cycle, constant error messages that made no sense (power failure when power didnt fail, codes that arent defined in the owners manual). To make a long story short, the company that does their warranty repair, which has worked on the machine approximately 8 times, tells me there is nothing else they can do, the machine is a lemon. But their customer service department refuses to replace it. They say it must be repaired, yet again. But the parts are out of stock (which should be a pretty good indication that theres a problem with product quality). So I am to wait. How long? They dont know. Call again tomorrow.Do NOT buy a Maytag appliance. Customer service does not stand behind their products and the products are no longer up to the quality I had previously expected from Maytag. Additionally, telephone wait times on the customer experience line can exceed an hour and are customarily over 30 minutes. Never had an experience like this with any other major appliance customer service department.

We purchased all new appliances 3 years ago including a Maytag dishwasher. Same problem as a lot of others. We had the control board fail three times in just four months. Now today the repairman came and while he was here contacted other Sears technicians and Whirlpool technicians. They came up with the idea to replace the detergent dispenser which they said is causing the main control board to fail. However, while the tech was on the line with Sears and Whirlpool they done troubleshooting on the detergent dispenser and found that it was all within specifications. In fact, that was not a problem because it worked as it should. But in their wisdom they decided to replace the detergent dispenser. We now have to wait another ten days for the part to arrive and reschedule another appointment to have the detergent dispenser that works replaced. The serviceman that was at our house said that they are making him replace a part that is working and that this does not need to be done but he has to take instructions from Sears technicians. Our service person said that he doesnt anticipate that replacing the detergent dispenser will make the dishwasher work but he said if it does it will only last a few weeks as before and then fail once again. We have the dishwasher on extended warranty and there are about 22 months. I suspect that this one will be going to court to get resolved. Never Maytag again or Whirlpool.

I just want to give an update on my frustration with Maytag dishwasher I wrote about on July 16. In the end, I found a DIY solution and fixed it. I wrote an instructables here: **. Not recommended if you dont feel comfortable repairing things. However, the diagnostic test at least can give you some clue whether its the control panel or control board is at fault before replacing both. Thanks.

I purchased my Maytag Bravos washer and dryer in July 2007. As with any appliance, we always purchase the extended warranty as it usually runs about $100 on appliance. My first experience with problems was in February 2010 when the control panel went out. If I had not purchased the extended warranty, I would have been in trouble. It ran out in July 2008. It was downhill from there. In September 2010, it quit spinning; and the fabric dispenser would not work. I called again in September 2010. The tub was out of balance. In June 2011, the panel control went out again. In November 2011, it would not spin. In June 2012, the panel for control had to be changed out again. In July 2012, now the pump is leaking. And guess what, my extended warranty is up 8/1/2012. I contacted Customer Service, which said unless there was the same problem within 12 months, there was nothing they could do. Well, Im fired up. I intend on making a complaint with the Better Business Bureau and anyone else who will listen to me. I paid over $2000 for the washer and dryer, and it should last more than 5 years. This is ridiculous! When Whirlpool bought out Maytag, then the product went to crap! Dont tell me the Maytag repairman does not have anything to do now, because I know I keep him real busy. I am so tired of the companys just blowing you off when you work hard for your money and purchase a product for your family that should last at least 10 years. I am a principled person, and this is not going to go away easy. The repairman is coming next week to fix it again. I am going to give him an earful as well. The last one who came to change out the panel board (3rd time) said they had nothing but problems with this unit. Well maybe they made it that way, so when the warranty runs out, they can charge you an arm and a leg for the part and the labor to repair. I will never buy a Maytag product ever again. My next one will be the new LG washer and dryer. Talk about the lemon law. This product from what I am reading here should very well fall within that category.

My name is Luis ** and I own a Laundromat in Yuma, AZ. I recently purchased 10 Maytag top loaders model MVW18PDAWW in August, so the machines are practically new. They are the new HE top loaders with locking lids. Since I purchased them I have had nothing but trouble. Customers have complained about them on a regular basis; there are days when we have had as many as five complaints.First of all, the locking lids proved to be a much bigger problem than we anticipated. People want to open top loaders to add fabric softeners and when we have opened them so that they can add the fabric softener they are often disappointed with the level of water in the washer. Those people consequently refused to use those particular washers. People have pressed the buttons on the control boards and sent the machines into a loop; different readings have appeared on the screen. Some of them say out of order, sync and several other error codes. Eventually the machines reset themselves or I have had to reset the programming. In the meantime the people pass the word and those machines are not used by those who hear. The controls are too sensitive and are not suited to a commercial coin laundry.Whenever any buttons on the control board are pressed the time of the wash appears on the board. Because of this some people who are busy and are using and loading several washers claim that they have already put their money into the machines; they argue with the attendant or with us. Many times they actually believe that they have placed money in the machine and many times they try to get a free wash from us. Either way they are unhappy and they, and those who hear them argue, will not use those washers again. In most cases we lose them as customers and once customers are lost they never return.I placed them in a location where the previous Maytags had been heavily used, expecting them to replace the old machine. I was wrong. They are used very little and the long and short of it is that we are losing money and since our busy season is coming up, will be losing even more customers and therefore more money. I spent close to $12,000 on the machines, including delivery and installation and right now they are quickly becoming heavy paper weights. I have contacted the salesman who sold them to us, but he has given us the runaround and done nothing about the situation.

We bought a Maytag washer and dryer in April 2012. A few weeks ago the washer while it was spinning out, it sounded like it was metal on metal. Sears came out and said the transmission and the tub had to be replaced and the tub was created to the transmission. My husband and the only ones living in home and I sort my clothes, so I dont have big loads. I contacted Maytag, their answer was its out of warranty so we are not going to do anything for you. Anyone who buys a Maytag Washer, watch out what youre getting.

Brand New 2019 Model 465 Washer and like others are saying is a piece of junk as they do not fill the drum with enough water even on the Deep Water fill option. The laundry does not circulate and nothing gets clean. Maytag is really poorly designed and manufactured these days and a complete Rip Off!

I have written to Whirlpool about complaints with this range and was very dissatisfied with response. The following were complaints on above range: Range does not have a light on it as the past ranges had. It is very much needed. Grates on burner are to high, therefore it takes longer for items in pot to heat up. Type of steel used on range is very thin and tiny, in other words very poor quality. This is what has happened since Whirlpool bought out Maytag. Quality of Steel that Maytag used is no longer since Whirlpool took over their products. This is true of All their Appliances (Refrigerators, Washers, Dryers, and Ranges). All meaning appliances manufactured by Whirlpool.Manual knobs for turning on oven have been replaced by touch screens, these eventually wear out and are very costly to replace. If it works why change it. Drawers on bottom of range used to be larger, now they are narrow and smaller height wise. Residue on base of burner appears quite frequently and has to be cleaned even if no overspills occur. And why cant Whirlpool make quality merchandise as good as Maytag use to make. Regarding the physical appearance of Range it is very attractive in looks, however Looking good and functioning poorly with inadequate materials used in construction of Appliances outweighs benefits of looking good. My wife and I regret not returning this appliance within 90 days of purchase. In the future we will not purchase Whirlpool or any other appliances manufactured by them if that is possible. Kenmore, LG and perhaps other appliances parts are made by Whirlpool. I received a response from Jake **, Whirlpool Corporation, Executive Office. The Comment from Jake that did not impress me was this: While we regret you are dissatisfied with the current design of your Maytag Range, this is the model that you selected. His comment says too bad better luck next time. Letter was dated March 5, 2014 received on March 13th or 14th.I sent a handwritten letter to Mr. Jeff Fettig on March 12th which was written on March 11, 2014. No response to handwritten letter to Mr. Jeff M. Fettig. Verification that the Executive Office that my email to you Mr. Jeff Fettig Chairman and Chief Executive Officer Whirlpool Corporation was received on February 20, 2014 by Delores **, Corporate Office Staff. Supposedly Mr. Jeff Fettig.

Purchased a new top loading HE washer in 9/2012. This machine gets very little use - approximately 10-12 loads a month. It is now broken awaiting parts which will cost about $200. Of course the warranty is only good for 12 months There is no excuse for a washer this new breaking and costing this much to repair. What a piece of junk! Avoid all Maytag products.

Hate my Maytag Centennial Commercial Technology washer. It takes well over an hour per load. Clothes come out very wrinkled, and my knits get holes very quickly. I would not recommend this machine to anyone. In fact, I warn people against it as I have been frustrated every single time Ive used it. Model # W10420382A.

I have spent a lot of effort leveling my machine, and my wife balances the load very carefully, but 10 times during a cycle, it will start slamming the tub around, so loud you can hear it from the street. I, like others in this forum, thought I was buying the best washer in the market, and paid extra for the Maytag name. It sounds like from the other complaints, that my problem is just the tip of the iceberg. It will cost me $200 to replace the suspension rods. I wouldnt mind paying the money, if I thought it would fix my problem. After reading about all of the other problems with the Bravos, I might just cut my losses, and get a new one. What a waste of $1,000.

We purchased a Maytag refrigerator model # 1TXEGMYWOO. The refrigerator part froze all of the food in it. We moved the temperature selector to the last place (two notches away from the recommended setting), and the food still froze. The furniture store we purchased it from replaced it with another refrigerator (same model). And that one did the exact same thing. We had to throw out more groceries. Obviously, this model is defective. We are now waiting for the store to replace this one (with a different model and brand). They have been very good about trying to make things right for us. Maytag, however, is a different story. They were very rude and indifferent when I called to complain. Their policy is to repair or replace the part (temperature gauge). I dont want a new part. This is a new product. And I bought it expecting it to work. I have had to throw hundreds of dollars worth of groceries away. I was very disappointed in their attitude. I will not purchase another Maytag item again. They used to have a good reputation. They now sell inferior products and do not stand behind their products.

Maytag Commercial # MVWB765FW0: My husband and I wanted to get rid of our GE front load. It was horrible. Even constant cleaning and leaving the door open all the time, our clothes still smelled like mildew and musty. My hubby wanted an LG and I said no way. As a little girl my mom had an old wringer washer and her first electric washer was a Maytag in the late 50s. She passed away in 2001 and in her lifetime she had 2 electric washing machines both were Maytags. They were so dependable and built to last so naturally I wanted a Maytag. Wrong! I am so disappointed. We purchased it in Sept of 2017 for $695. I was so excited the first time we used it. It was a little noisy, but living in the county and having a well we were glad it was an energy/water saver. The first couple of months it was so refreshing to have clothes that did not smell musty and mildewy. I noticed they were really wrinkled but I still iron anyway so it was not a big deal. However ironing over and over again on some items did not get rid of the wrinkles and the past 2 months I have been going thru lint rollers like crazy and it still does not come off. I have to use a slightly damp lint brush or go over the clothing with packing tape to get the lint off. It is horrible! I dont want my GE back but I dont want this one either! I wish I would have read reviews first and listened to my hubby. I wont ever have another Maytag and when this one goes I will certainly read reviews and go with something more dependable. Unfortunately for now we have wasted the money and it is ruining our clothes! I agree that we should all do the class action. There are just too many of us experiencing the same issues. Maytag should do right by the consumer! We have learned our lesson, review before you buy!

Failed control panel Quiet Series 300 - After seeing countless notations on the net concerning failing touch panel and control boards, now my relatively new dishwasher has started its demise. It is terrible that so many people have the same problem. I sent an email to Maytag and have promptly been ignored. Unless it sets your house on fire, I guess they are not interested as I am no longer interested in supporting this product. It is nice that you can post such similar design failures for the world to see. Thanks Maytag!

I bought my Maytag Bravos top load washer from Home Depot. In one year. I had the Maytag warranty people out three or four times. The warranty ran out and I purchased an extended warranty from A&E. I have had them out at least five times.I called Maytag and they told me since that I didn’t get the extended warranty from them, that there was nothing they could do for me. I explained to them that this washer cost me over $900 and that I have had numerous repairs on the washer, in which the warranties cost me over $400 so far.How much do I have to keep paying for this lemon? Maytag will not do anything about it! This goes to show you that paying top dollar for a washer does not guarantee you will have a good product. In this economy we can’t afford for this to happen. This is a very bad product and Maytag will not stand behind their own products, but they are willing to charge the consumer high dollar for them. This is a disgrace!

We purchased a Maytag electric convection oven with a warming drawer 3 months ago. We have been happy with the cooking features, but not the Aqualift self-cleaning. It does not work and Maytag does not acknowledge this. Instead they have offered cleaning products to us which their own instructions tell you not to use! Does this sound like a self-cleaning oven? They have offered to send out a service person to check the temperature. However, from reading multiple reviews by others, there will likely be no satisfaction from this company.

The control panel of our Maytag dishwasher stopped working when it was approximately 14 months old. We repaired it ourselves by following a reset directions we found online (push rinse button 5 times and then the cancel button twice). Also we cut the power to reset. Im not sure which of those two tasks reset it, but it worked until last week - now 28 months old. We are not able to reset the panel using any information that we can find. In trying to find repair options, we discover that there are a lot of complaints about the Maytag dishwashers control panels not working within just a couple of years. In speaking with Maytag, they tell me theres a class action law suit for this problem - meaning they do realize there is an obvious problem with their control panels, but are not acknowledging they have any responsibility to repair it. The law suit only covers the cost of the part but not the labor. The labor can cost between $100 - at the lowest - and up. Our Maytag dishwasher model # is MDB8949SAM1. Also noteworthy, our Maytag clothes washer gave out at less than 5 years. Maytag is no longer the company we all thought they were. Additionally, their faulty machines are costing their customers a lot of extra money. Not exactly what I would call a company with good customer service or even any ethics. We will never buy Maytag again.

I purchased an expensive Maytag washer & dryer, top loading, energy efficient, only to find it now shreds all of my towels, robes, dress, undies etc. Maytag reply was to put things like undies, t-shirts, & dresses in bags to wash... What about towels? I had an expensive white Terry cloth robe from Neiman Marcus which is now shredded, Im showing it to everyone. Plus the dryer has an area above the front door that snags everything. I open the door & clothing is hanging there, caught on this area. Tell everyone not to buy Maytag, theyre rip-off. Ive lost more money on ruined clothes & linens than the trash washer & dryer are worth, but Im disabled, handicapped, 61 yr old who cant afford to buy another new washer!

I purchased Maytag Washer and Dryer 3-4 years ago, upgraded to the premium washer and dryer, SS drums and have been dissatisfied from the start. The washer was extremely noisy; we were told this was normal. The dryer began making strange noises just outside the warranty period, and the belt and pulley had to be replaced. I was shocked at the cheapness of the pulley design, but the replacement part was of better quality. The washer began making a horrendous squeak shortly afterwards, again, outside the warranty period. The repairman said that they were all like that, Maytag used inferior transmissions and that it would be cheaper to replace the washer than repairing it. My mother had the same experience with a similar model. Needless to say, I will never purchase another Maytag product. FYI, there are only three people in our household, all adults, light duty use.

I purchased the Maytag Bravos washer and dryer set one year ago, and have asked myself why ever since. The oversized laundry tub is what attracted me to the model, but it sure doesnt deliver for the money it cost. On normal settings, it doesnt use enough water for all the clothes to even get wet. After the load was complete, there were areas of my clothes bone dry, and obviously still dirty. I soon learned that the only way the washer uses enough water to get all the clothes wet and clean, was to set the machine on the bulky setting. This is the only setting I use now, but all of my clothes winds up twisted together, sometimes in one big ball. As for efficiency, that statement folks is a joke! Because I use the bulky setting, it uses much more water than a traditional washer ever did, and when the load is off balanced, it will go through another rinse cycle to try to even it out. This machine uses far more water and electricity than my old school set! I suppose if you dont get your clothes dirty, you may not need to use the bulky setting, but thats the only way I can wash my laundry with this machine. The old style set I had before this was Maytag also, and lasted about 20 years. I was more than happy to purchase Maytag again, but this set has been nothing but a disappointment. I dont plan to buy another energy efficient machine again, nor would I recommend this product to anyone!

My Maytag has been out of service more than in service and this is my 2nd one in 2 years. They replaced my first one due to breaking down several times. I have spent so much $$ at the laundromat after paying big bucks for a washer.

The washer machine is only 2 years old and its broke, at first it wouldnt spin and now it wont wash. Everyone is saying between the parts and service fee, it will cost 200 to 300 dollars or more to fix, most technicians wont repair them because they say that we may as well cut our loss and just buy a new one. No one likes these machines. I wish I would have known what a sham the washer machines were before purchasing.

I had the old style machine and finally it gave out and I bought an LG HE Large capacity. It was a well I can print it here but kept the machine for 5 years and gave it away. I bought a new Bravo Maytag set 5.2 with the old style agitator thinking I was going to get a great machine and NO. These new machines do not use enough water in the load sensing and clothes on top never get in the water. They come out with soap stains even with a double rinse. And no I am not using too much soap! My old machine had small medium and large load settings plus you could add more water if needed. Way better machine.The techs are trained to tell you this is how the machines work and there is nothing wrong with them. Finally an honest tech told me they are having all sorts of complaints and problems. If all you wash is bedding and dress clothes you get by but if you really have soiled clothes you have to do a lot of prep and then stop in the middle of the wash cycle and rotate your clothes manually! Total BS for 8-900 dollar machines. Do yourself a favor and buy a front load. At least the clothes will get flopped in and out of the water and hopefully rotate so they actually get clean. That is what I am going to try before I go back to the old scrub board and tub!

My Maytag refrigerator is less than 5 years old; the compressor went out (only warrantied for 1 year, 5 years used to be the minimum). I contacted the company who now owns Maytag, I believe Whirlpool. They told me they can fix it, no matter what the problem is, for $380.00. It turns out they sold me an extended warranty, but that was never explained in the conversation. Prior to contacting them, I had Sears out to fix it; they are the ones that told me it was the compressor. 1 week after buying the extended warranty, the repair company came out to fix it and found out the refrigerator was unplugged and informed me it needed to be plugged in for 24 hours in order for him to determine what was wrong with it. I scheduled an appointment 1 week later. When they came back, they said it was the compressor, and they needed to order the parts. 1 week later, they came back, and the compressor they came with did not work. 3 weeks now, no refrigerator. They said they would put a rush on the order, haha. Now, I have to wait another 8 days for them to come out to repair. 4 weeks without a refrigerator? I think there is some type of implied warranty when you purchase large appliances; these companies are getting away with murder. Are refrigerators now disposable commodities? Cheaper to buy new ones than repair the new ones? What will happen to our landfills?

I mistakenly purchased the Bravo XL top load washer. I only wish I could give it a zero rating. I have only tried to wash 3 loads of clothes. It is almost beyond belief that anyone could possibly think this could clean anything. My husband actually watched it “work”, and insists I call Maytag because they must have forgot a part! It does nothing but crumple/wad the middle items together and rub them...and only them...together. There is no movement of the outer items until it spins. Maybe Maytag should enlist people who actually do laundry to “test” the items they put their brand on. I know the government and the energy rules have added to the complex problem of buying something as simple as a washing machine...but this piece of junk is almost laughable to watch as it destroys your laundry. I’m almost embarrassed to let anyone know I bought it. Thankfully, I have 30 days in which to return it.

I waited my entire life to age 47 to purchase a brand new matching Maytag washer and dryer. I was thrilled. That was August of 2012. 3 years and two months later, the $800 dryer (MEDE201YW) loses the entire control panel and Maytag refuses to offer any assistance. I deliberately purchase Maytag with its stellar reputation, an American based company only to be more disappointed in the product and the company than in any other appliance Ive ever purchased.

Wish I had reviewed Consumer Affairs reports. When our old Maytag stove required repairs we decided to upgrade old stove instead of putting money into old unit. Looks like a huge mistake. Not only was there a delay in receiving unit after placing order but oven will not preheat. Two weeks before Thanksgiving we were promised a working unit. Now we are only 2 days from Thanksgiving, 2 repair companies have been at home to repair. Requires new circuit board and a new regulator to repair and no promise we can obtain parts. Now I have to figure out how to feed my family for holiday. I am pretty well done and after reading other reports that they are better in junkyard I think I will try to make them take back this defective Model 8800 product. Sitting in our kitchen unusable for the holidays. Dont buy Maytag as customer service does not exist.

I owned an front loading Maytag Neptune Front Load Washer MAH5500 for more than 10 years and first 5 yrs doing 2-3 loads a day for a family of 12 so this machine held up well, and only issue we had with the machine was the rubber around outside needed to be replaced after about 9 yrs.

It doesnt clean as well as the cheap GE model we have at our beach cottage. Also it is very noisy. Disappointing. Will never buy a Maytag dishwasher again.

Problem with the front panel are the dishwasher has been replaced 2 times in 3 months. Was told by the tech repair person is not a well made product. He would replace it if he could had a warranty and added a new warranty for 1 year and is up again and of course have to do it. Was told if it happens again they most likely replace with a new unit. Hopefully. Not happy.

Similar to dozens of others, we purchased a Maytag dishwasher from Home Depot in March 2011. Recently, it stopped working, dead - no lights, no action. Called Maytag and they referred me to a Maytag Repairman: Coastline Appliance Service of Huntington Beach, CA. The serviceman came out and spent 20 minutes, checked the door switch for continuity, and declared the control panel bad. How do you know its the control panel, I asked. Its my gut feel, based on experience, he said! He charged me $129 for the visit and said a new control panel would cost $380! After reading other posts online, I can only conclude that a new control panel (if that is, indeed, the problem) will also go bad in the next year or two. So, like so many others, were off to buy a new dishwasher - and we will never buy a Maytag or Whirlpool appliance again.

I moved into my home in July 2013. My kitchen came with all stainless appliances that appeared and seemed to be in excellent shape. I have been using the Whirlpool Microwave oven to heat foods (all in microwave safe) containers and dishes. This morning, I was heating a muffin, when suddenly I hear popping. When I looked through the glass into the inside of the microwave I saw sparks then flames. I immediately stopped the microwave. The fire apparently started in the area of one clip that holds the metal rack inside. In researching this issue online, I found hundreds of complaints from people who have experienced the same issue, and Whirlpool refused to replace the unit because it is out of warranty.

Within the first year of having this washer (Maytag Bravos X series) the cam broke in it. And then about two months after the warranty went out, the motor quit. It wouldnt spin my clothes at all and would never get my clothes clean. I was having to hand wash my clothes just to get them clean. Not a very happy person, I live paycheck to paycheck and cant afford rock continuously pay to have my washer fixed.

My Maytag dishwasher MDB780AWW2 was recalled due to electrical problems. They gave me a voucher to purchase another one, plus I had to pay another installation fee. New unit was installed in February 2011, and here I am with a control panel issue. Seems like a similar problem, too. The lights light up, but the dishwasher wont start. Its another $345.00 plus tax repair by a repairman.

Zero should be a choice on overall experience. I purchased a Maytag Bravo 300 from Lowes in February of 2011. Last week I was doing a load of laundry and the washer stopped in mid-cycle, and it gave an alarm and error code ld. I checked out the manual and it said there was a problem with the drain line. I check the drain line and it was fine, so I called Maytag to have a service man take a look at it. Before he even looked at the washer, he said it was probably the pump, and it is not covered under warranty. And he said that it would cost $140. He obviously sees this all the time. He explained that the pump is too small for the unit and it does not allow anything to go through the pump. Please make sure anyone who may be considering buying one of these units knows right up front that they are going to have issues with the pump, even if a small pebble gets caught in the pump.

It washes extremely well. Its reliable. The wifey loves it and thats enough for me!!! I have had no major mechanical issues. Since 2012 we use it heavily and every other day. I would purchase same brand if need be but Im confident that would probably be in 2024.

I am not dissatisfied with hhgregg, but with Maytag products. I purchased the Maytag Centennial Top Load Washer and Maytag Centennial Dryer to match. I was a bit leery of the new energy star models that use he only type detergent, but decided that was the newest and greatest thing out, so how could it be wrong? For the past two months, I have been sooooo very disappointed in Maytag. Neither of these brand new machines are worthy of being considered brand new. The washer takes extremely too long to wash a normal load, too noisy, and has ruined several items of clothing, due to malfunctioning distribution of bleach, fabric softener released after clothes are through washing. There has also been several times that the load wash is complete and the clothes are not even wet (like they were never involved in a wash cycle). As for the dryer, you have to run it through two 40 minutes cycles to get the load of clothes completely dry, so much for energy-saving. This is my first complaint to anyone, but after reading several reviews on Maytags website, I am reassured I am not alone. There are hundreds of other dissatisfied consumers of this Maytag product. I will be writing a letter to Maytag, requesting a refund.

I purchased a Maytag Bravos washer and dryer pair in 2009. Over those 5 years I have had at least 8 shirts come out of the washer with tears in the armpits. First I thought it was my armpits destroying the cloth. Then I thought it was cheap cotton (all my shirts are 100% cotton) from foreign manufacturers. Ive had two shirts destroyed this week, this mornings was really thick material. Usually when I remove clothes from the washer, they are entwined and twisted. Consistently when I wash any load including a towel or two, the washer becomes unbalanced. My clothes often have a foul odor after washing. My theory is that the lack of a center agitating spindle is allowing the clothes to tangle, and not really cleaning them. I have to use the extra rinse setting or the clothes come out covered with soap suds. In summary, Im not happy with this washer and will never buy another Maytag appliance. Im also not sure the high-efficiency technology has had all the kinks ironed out.

A week after warranty expired, our 1 year old Maytag gas range (model# MGR7662WS 4) required new Direct Spark Ignitor (DSI) board. Knowing it was just beyond warranty, I inspected wiring first and found that the Bake connector on the DSI was loose, flopping around from a bad solder point on the board. Called Maytag and informed them of this manufacturers defect and all they offered was a $20 discount on a replacement part ($220 instead of $240). It worked with new part for 4 days, then something else went bad causing oven to spark, light, heat to less than 100 degrees, then shut down, then restart, then shut down, then restart, then stop doing anything. It has never worked correctly since then. How can a manufacturer of almost all domestic brands get away with such shoddy workmanship.. Taking advantage of defective or poor quality parts to sell more of the same when they fail and for an enormous markup? Where are the regulators who oversee monopolies and blatant scamming of American consumers?

I purchased Maytag washer/dryer set in Feb 2021. In June the washer broke. It took 2 weeks to get repair person to look at it. During the appt no faulty product was identified so they dont know what to replace. No parts were available. A follow-up appt was set for 1 month later. No parts are available to make the repair so a follow-up appt would be futile. . The only communications other than No Parts is that they want me to purchased an extended warranty. I will never purchase another Maytag product or recommend them to anyone. Meanwhile my warranty continues to time-out and they dont have any parts or idea when they will be available. Im not sure how a company can sell products that they do not have some level of support for those products. Beware of purchasing Maytag Products.

We bought a new dishwasher 2 years ago. Top of the line Maytag Model #MDB8959SBW3 $749 plus tax. We bought this one because they told us what a great 10 year warranty it had. Found out that is a lie. The only thing the 10 year warranty covers is the stainless steel tub, the racks and chopper blade. The stop button on the control panel (circuit board) quit working and the dishwasher wouldnt start. When I called Maytag they said So sorry. It broke so soon, but that is not covered.We were told by a repair shop that Maytag has had nothing but problems with their control panel and the control panel part alone is $150 plus tax plus installation. Our old Maytag lasted 13 years and was still running great, but needed to be replaced because the racks were rusting out. I wish I would have kept the old one. I will never buy Maytag again since it is now made by Whirlpool. If Maytag is having so many problems with their control panel, they should be recalling them.

I bought this Maytag French door model MFF2258VEW2 in 2010. Within the first year, it was freezing my vegetables. They sent someone out to fix it. Thank goodness it was under warranty. The man laid the bill down and it was over $800 to fix it. Six months later, it froze up. I called and they said they would send someone out, but I would have to pay for it. Im on disability and cant pay that kind of money. I got someone to come out and fix it. Well, guess what? It has started freezing my vegetables again. This is the third time this thing has gone bad. What do these people think they are doing putting things out like this? I had a Maytag for 30 years and never had any problem with it. So I saved and saved to get me a new one but I will never buy another Maytag. The company should have to replace all the refrigerators that are like this one.

I purchased Maytag Bravos XL Steam Washer brand new from Lowe’s in January 2018. HORRIBLE washer! Does not get clothes clean and leaves soap and scum all over clothes. I have to wash everything on power wash with an additional rinse cycle (takes about 2 hours per load) and clothes still don’t come out clean. I often have to wash a load 2 or 3 times to get it clean. Will NEVER PURCHASE another Maytag product! What is even worse is that I also bought the Maytag “commercial technology” washer at the same time. It’s an even more TERRIBLE washer. Cannot get through one cycle without getting an LF (low flow) error & the cycle shuts off and machine drains & quits. Absolutely the two WORST washers I’ve ever owned in the past 40 years!!!

I purchased my Bravo (MVWB300WQ2) washer a little over two years ago. It took all day to wash some loads due to leveling problems. Example, you could not put more than two bath towels in at a time, even with the towel setting. The washer would stop and you have to re-position the towels. You cannot leave because it stopped so often. Also, the washer makes an extremely loud noise during the spin cycle. My most recent problem, it does not complete the spin cycle. My clothes are still very wet. I refuse to call service. Its just too costly. It would be the third time in less than 3 years. However, the first time was within the year warranty (no charge). The basket had to be replaced - it was ripping my clothes. During my second service call, the technician advised me in purchasing an extended warranty. I paid for the service call and for a one-year extended warranty which just recently ended. The washing machine is not worth paying for service again. I am going to purchase a new machine instead!