OK, Im at wits end. I bought a very expensive Maytag Gemini range four years ago. Since then, I have replaced 10 burner valves. There are only five of them. They have each been replaced twice, and tonight yet another has broken. This time it is broken in the ON position, which means I cant have the range on without that burner on. It means unplugging it when not in use and lighting the burner with a match when I re-plug the stove, until I get it fixed. I had just replaced valve number 10 on Tuesday, and had a fully working range for only 5 days. These valves are under warranty but the labor is not, and it is always close to $200 to have someone come out to replace them. I cant afford a new stove and I cant afford to keep having these defective valves replace.

I purchased a Maytag Centennial Commercial Technology washer in September 2010 which is less than two years ago. It decides to stop spinning correctly in the Spin cycles. Clothes come out sopping wet so I contacted Maytag to have a tech come out. On the day that the tech came out from A&E Factory Service, he stated it was a switch. He changed the switch and still, it did not spin correctly. He then proceeds to state that it is another part, which again, it did not do the function correctly. He then proceeded to state that it is the clutch, then the transmission. The cost was raising to $519.00.I stated that I did not want to proceed because I would be purchasing a new washer with that quote. I stated to place all the original parts back onto the washer. He did so, but did not place them on correctly. The casing of the washer no longer is secured to the drum - bolts and plastic pieces are still on the side. He left my house with finger prints of grease on the walls. If this is the workmanship that Maytag recommends, then my business deserves to go elsewhere.A complaint was filed with the A&E Factory Service. However, no one has contacted me about the complaint as was requested. All I want is for my washer to be fixed or to have a tech who is knowledgeable to come out and fix it. I contacted Maytag to inform then of the situation and they stated that all their techs are certified. I do not believe that my washer of less than two years old could possibly have so many parts that are faulty. I hope that this may, in turn, help another consumer to avoid purchasing washers through Maytag and their parent company, Whirlpool.

Maytag Model #MGR7662 range - We inherited this oven when we bought my mother-in-laws house 2 years ago. We had to get a thermometer to keep in the oven since the temperature is never consistent and is usually 50-100 degrees lower than the digital readout. We will be replacing this oven as soon as we can and it will NOT be a Maytag.

Perfect for me. It would be better if I had a space to put it without adjacent walls. Mine sits with the refrigerator door against a wall and I have to pull it out to the door space to open it wide enough to pull out the drawers to take them out for cleaning. Otherwise, it has worked very well for me by myself, for me and my husband when he was alive and for my son and his family and myself, and he has 5 children.

Maytag Centurian is a terrible product. I dont think the designers of this model have ever washed and dried a load of clothes. Washer problems: The lid (top loading) locks so user unable to determine if the correct amount of detergent is being used. There is an unlock button, but it takes quite a long time to unlock (maybe 15 seconds), then an even longer time (seems like a minute or 2 to restart). The machine is LOUD and at one point in the cycle BANGS. I actually returned the first as defective, but when the 2nd machine made the same noise, I was told, no, thats the way it is. It seems to take much longer to wash a load than my previous machine. The Power Wash tears my clothes. Even the regular wash puts holes in my thin tee shirts after a few washes. Really had to get spots out. I almost have to hand wash to get the spots out BEFORE putting in the machine. Dryer Problems: Takes 70 minutes or more to dry a normal load with a couple of towels. The cover to the lint catcher doesnt seem to be properly sealed. Lint particles get all over the top of my dryer. I bought this Washer/Dryer combo last year. Im annoyed every time I do laundry.

I purchased this Maytag Bravos machine because I was told it can wash large loads and is one of the best washers out there... Both are so far from the truth, this is the worst machine I have ever owned. The water level is almost none. And my clothes come out dirty and I have to wash several times to even get them semi cleaned. I am not rich and trying to save enough. To buy this machine was not easy and I am now with no options. I called Lowes after a couple day after I got the machine and told them it is not working. They sent me another machine yet it still does not clean my clothes. I wanted to return it and get a better machine but they refuse to allow me to do so because now it is 2 months old and past the 30 day return. I purchased an extended warranty which is useless cause. The machine is junk even when working as it should... I will never buy from Maytag again because they refuse to back their crappy product and refund my money. I would tell anyone looking for a washer to not go with Maytag. They are terrible machines and a bad design... I even contacted Maytag and was pretty much told too bad and just rewash my clothes as many times I need but they will not do anything to resolve this issue. TOO bad is what I was told...

We purchased a Maytag double oven in November 18, 2008. I was baking and the top oven wasnt working. We called Maytag service number on the book we received when we purchased the oven. It took 25 minutes for someone to answer our call. The person did not know what our problem was. We thought it could be the ignitor. He transferred us to a parts person. That person didnt know the answer and hung up on my husband. How rude of him. We will never purchase another Maytag product. We will let our family and friends also know. You need to inform your personnel to know their products.

Bravos XL top loading washer looks nice and very large, but thats about how deep it goes. It leaves even a small load half-unwashed unless you select deep water wash and even then it FAILS TO USE ENOUGH WATER. I tried to go and fill it up once with tap water and it totally DRAINED THE WATER AND SOAP before it unlocked! It was on Deep water wash and the top of the load was totally dry as I dumped the hot water onto it.It is a bad design and it should have never been sold. I know it has special places designed only for HE detergents but when you try to use a Tide Pod the detergent NEVER FULLY WASHES OUT OF THE CLOTHES.... Too small a load, too big a load, exactly 5 pounds or exactly 10 pounds it really doesnt work very well - AT ALL! I was thinking that I might like to get some SHOS at the low price it is but now I can see why they are definitely not getting back into business.

Our Maytag Bravos is 4 years old. Settings are preset at the factory. Besides the glitches others have written, the hot water sensor INSIDE the machine has gone out. This means - no clothes can be washed on the hot setting, and the warm setting gives only lukewarm water. I have had more than one plumber look at the machine, and the consensus is...the internal sensor needs replacement. However, this machine being only 48 months old, I am debating whether or not just to buy a new machine. This is a HE washer, and I am very disappointed in its performance. This is the worst Maytag machine I have ever owned.

Our problem started when the control lock button locked itself on. Called Maytag and told it wasnt covered by warranty but they did walk us through resetting the power and it fixed the problem until we ran the next load. Now when you try and set it, the rinse only light comes on. Bought the Maytag because I always believed them to be dependable - wrong!! I had a basic model Whirlpool running for a family of 5 for 25 years prior to this Maytag without ever having to call a repair person. Maytag wont deal with the issue so I would recommend to anyone else having any issues with unreliable appliances to do what I am doing - boycotting Maytag!!

We bought a Maytag Neptune front loading washer from Bens Maytag in Surrey four years ago and it has been nothing but trouble. There is no screen in the machine to prevent small things (like coins, screws) from going behind the rubber seal and into the pump. As a result, coins frequently block off the outflow to the pump so the machine doesnt drain.We have had to pay for service calls more times than we can count, and have spent more than original price of the machine making repairs and replacing the pump. We now have learned to take off the hoses and open the pump to remove coins ourselves, which we have to do every few weeks! Bens Maytag tells us that its our fault for letting coins go in the wash. There is no accountability for the faulty design of the machine that allows this to happen. We should have cut out losses and thrown this piece of junk out three years ago. We want Maytag to take responsibility for the faulty design of this product and to credit at least our purchase price toward another machine that works properly!

I purchased a Maytag refrigerator 4.3 years ago. Model #NSD2572VEW01 side-by-side. Came home to find water on floor. Called for service at a local company. Tried several new parts, only to find out I had a bad compressor. Part cost $358.30 + labor charge which couldnt be estimated because of difficulty with installation. Called Maytag for help, was told FIVE times, Sorry, nothing we can do to help you. Have never had any other appliance in my life except Maytag. NEVER had a problem with anything before. Have washer, dryer, fridge, stove, microwave, and dishwasher. Found the answer to be unacceptable!!!

The top of the range has blistered and has worn off. It cannot be cleaned. I spoke to a Maytag representative and was told to try and use magic eraser to clean around the burners. This did not work. The model number is mgr7775xs. Is there any solution to this problem. My range looks terrible.

We bought the Bravo XL set 11 months ago and the washer leaks all over the place.. Called Maytag and had the repairman show up. Upon arrival he told us these were the worst machines to buy and would never recommend to anyone. He also said that business has been great due to all of this.. He checked the washer and said the water pressure was too high and lowered it. He couldnt find anything wrong with it. After he left I started a load and sure enough it was the same. Called him right back and he said to call Maytag because he was going to another repair job. I called Maytag again and they said to call the repair guy.. Never again will we ever buy Maytag.

We bought a Maytag dishwasher 4 years ago, we had to have it serviced a few months after purchase for the soap & rinse agent dispenser not working, then a few months after warranty was up the buttons on machine wouldnt work, the control panel failed so we had to pay for a new one and install it... Well last night exactly one year from the install of the new control panel I walked into my kitchen to find it full of smoke and the dishwasher pour out smoke, when my husband came home he took the door off and sure enough the control panel was burnt and melted! Very scary. It is a very good thing I was home and this is why I never leave appliances running if I am not home.

We bought our Maytag dishwasher because of the topnotch features; such as 10 year warranty, low noise level, maximum cleaning power and it looks great. The dishes come out exceptionally clean and don’t needs to be rinsed prior to putting them in.

This range and oven get unsafe, very hot on the surface and sides. Also, first time we used the oven, our oven mitts and bbq tools caught fire in the storage drawer.

The washer w10420491A is 2 1/2 years old and got the F51 code. The result is the hub bearing are shot along with a circuit board. I would stay away from any Maytag Bravos washers.

I bought this stove thinking of the Maytag repair man commercial that was advertised on TV for washing machines. Apparently Maytag only knows how to make washing machines (I did not buy one of their washing machines after my experiments with their stove). From day one the oven door never closed right, the self cleaning oven device had to be replaced 3 times over the year after have a repairman tell me that they all fail. I stopped using the self cleaning feature. This stove has cost me so much in repairs. The cook top is very very hard to clean. It always looks dirty. All the plastic knobs have melted off because the oven door never closed right. And the knobs are crazy expensive to replace as is just about everything on this stove. The oven temperature can not be trusted never cooked at the temperature it was set at. I paid a lot of money for this stove 10 years ago. And I am finally able to replace it thanks to a Christmas present from my 3 children. I love to cook and this stove made it difficult. My advice is to look for a different company when buying a kitchen stove. This Maytag has been nothing but trouble for me.

I purchased Maytag microwave model MMV4205AAQ in 2005. I use it infrequently. It stopped heating in Nov. 2011. It must be replaced. But after this experience and reading other comments, I will not purchase any Maytag appliances in the future.

After 1 year and a month, the dishwasher would not work. When the Maytag repairman came, he told me that this was the 3rd one this month that had the same problem (the control panel). The cost to replace, it would be about $275. However, since I know of 3 that have broken, why would I replace it? I live alone and maybe have used the dishwasher once a week. There should be a recall on this machine. I called to see if there was a recall and was told Im sorry. I would advise anyone purchasing a dishwasher to avoid Maytag or any dishwasher made by them.

We received our new Maytag French door refrigerator today via delivery and got everything set up and magnets stick to the front. The last I checked magnets should not stick to stainless steel. So I called the Menards where we purchased the refrigerator almost 2 1/2 weeks ago and the store manager said there was metal liner under the stainless steel and states this on the technical specifications. And everywhere I went to look under the technical specifications NOWHERE does it state there is a metal liner underneath and even if there was the top is stainless steel regardless so why would magnets stick to it. I paid for a Maytag and basically got a cheap piece of crap Frigidaire or Whirlpool and paid extra for Maytag to stick a Maytag label on it. What a joke. If I have any other problems I will personally deliver this refrigerator to Maytag/whirlpool corporate and put it on the front step. I am VERY ANGRY!!

The fridge has a grinding noise that is getting worse, by the day. I cannot seem to define the exact location of problem, whether the freezer or the fridge. Maytag you stink, and your web site stinks, too.

Maytag gas range model #MGR8670XS 1 - I would not recommend this range. We bought it new and when I used the self clean oven, it did not work. It took four months to get this resolved. I self cleaned again, and I had to clean the oven by hand. It did not clean very well at all. I wish I had my old oven back.

Consider all other manufacturers before purchasing a Maytag dishwasher. Our 3 year old model MDB8949SBB1 is junk. The control panel is a joke. Works when it wants to. Do not spend your hard earned money on Maytag.

The Maytag Washer and Dryer we bought new and they have been great. The dryer was bought in 1972 and still works well. The washer was bought in 1997 and still does a good job. We are satisfied with the long time these 2 appliances have lasted. Do any appliances manufactured today last that long?

I have never reviewed anything and feel compelled to chime in. The Maytag Bravos XL is the WORST washer dryer set ever. My 20 year old tiny washer with agitator cleaned a million times better in half the time. In fact this washer doesnt even clean your clothes! The reason is because so little water comes in and you cannot manually control the amount of water. Ive tried deep water wash-total joke. Heavy duty wash and extra rinse, still no better. You can wash it 2-3 times with the same poor results. Who wants to put on dirty underwear! The dryer easily takes 2 cycles to get an average size load dry and forget sheets and towels! They take 2 hours.

My clothes sometimes come with white spots on them. My clothes are very twisted. I would LOVE to have Maytag replace my washing machine so I could again sing their praises!!!

Bought a Maytag Washer & Dryer and after only 4 years the front panel went...cost to replace part only $653.55. After expressing concern about the price Maytag cut the cost of the part in half - now installed $475.00. Disposable dryer. Choked on it and decided to go ahead with the repair. Part was to be in in a week and it is now been a month. Maytag/Parts supplier no idea where the part is and doesnt return phone calls. Have to use the laundromat (family of 5). More money out of pocket. Not to mention time. Called Maytag again to complain about the service and having to pay more money out of pocket to use the laundromat. They basically told me, Too bad. Have used Maytag appliances over the years and always been satisfied but the company is clearly going downhill.

I give the product lowest and poor rating. The bearing in our washer went bad 4 months after we bought it. For the fourth time, they are coming out to repair the washer on 01/11/2012.

A year or so after purchasing our new home, we purchased new appliances. We thought Maytag was a good company to go with. We had serious issues with our 2005 Maytag bottom-drawer freezer refrigerator right off the bat. It arrived with a large dent in the door. They offered to take $50.00 off the price. We insisted on one without a dent. They replaced the refrigerator, and shortly after, the board and the ice-maker went out right away.Although the parts were under warranty, we had to pay for the labor. The refrigerator is 6 years old and now it is making a constant knocking sound. We paid a lot of money for what we thought was a quality appliance. What a joke. We had also bought a new Maytag washer and dryer set and they fell apart after 5 years. It’s the same with the Maytag dishwasher. Do not buy Maytag appliances. They are cheap. They fall apart. The customer service is poor. I feel cheated.

This Maytag (Whirlpool) model MDB7749SBMI dishwasher was purchased 10/28/13 at Home Depot. That makes it 2 1/2 years old to date. It has been a good dishwasher up until now. A few weeks ago I noticed it was doing something wonky. First of all it was not responding its usual way when I tried to turn it on after closing the door. The start button was not responding immediately, nor were some of the other buttons. I also noticed that after the dry cycle had completed and the door was then opened to unload, that the lights on the door were flashing. Then, when I shut the door after unloading the dishes, the washer would come on without having any buttons pushed. Recently, in addition to the difficulty we are experiencing getting it to start, the washer will keep running without ever turning off. Last night I turned it on before going to bed, and it was still running this morning. Calling the service number, the control panel part will run around $150, with a $98 charge for repairman to come out. Who knows if that 98$ isnt just to walk in the door, and whether that includes the time it takes to install the part. The dishwasher was around $400 with my husbands military discount from Home Depot, so it seems crazy to spend that kind of money to have a part replaced that is going to break again because of PLANNED OBSOLESCENCE. If that part is replaced (at half the cost of the dishwasher) whos to say what other part is going to break next, perhaps requiring another service call plus price of part. So, conclusion is to throw this one in the landfill and purchase another dishwasher, sadly.The case of Planned Obsolescence is reflected in many of the comments/reports here on Consumer Affairs. The age of the failing control panels of the Maytag/Whirlpool washers are running around the same time spans. No doubt in my mind that these control panels are designed to fail after a specific amount of run cycles/time on this machine. These appliance companies that are manufacturing these total crap appliances so that people will have to buy replacements within 3 or 4 years are filling our already packed landfills while robbing the consumer. Its plain to see for all who care to investigate the matter. A service repairman whom Ive used for years and has been in the business for 25, told me that most appliances today are total pieces of junk compared what they used to be and are designed to fail. He said it has greatly impacted his business because people are replacing appliances versus repairing them because it is not cost effective to have them repaired. He also added that the guts of these appliances looked like they were made from Cracker Jack toy quality plastic materials. There should be laws to stop these manufactures from Planned Obsolescence, and we need to go back to the way appliances use to be made... to last! I have no idea what its going to take to ever see that happen. This is what happens when you have very little competition and 2 major appliance manufacturers. More parts are being designed to fail, so that they can line their pockets. Pitiful.

Washer stopped working, never did clean clothes. Out of warranty - some it is fix or buy a new one. DONT BUY!!

We have had this refrigerator, model MFI2665XEM7, less than two years. The ice maker stopped working and we had it replaced at least 6 times in a two month period. We had a solid ice sheet in the bottom of the freezer drawer and it leaks water on the floor constantly! Even today... after another ice maker replacement, we have no ice! I never wanted a Maytag, but finances and the small space we had gave us little choice. I am not sure what our next move is. I will NEVER buy a Maytag product again! I should have google this sooner and we could have saved the poor repairman all of those trips!

Same as all the others, bought this dishwasher about a year and a half ago for a new home. Didnt get the CO until 3 mo. ago and already having same problem with the keyboard flashing and not working properly. Very pathetic to believe less than 100 washes and were going to need a new washer, that works out to be about $ 5.00 a load. Wish someone could help. Model mdb7749sbb0. Thanks.

Dishes did not get clean. Bowls would stand up when you placed them in the dishwasher, then fall over when the door closed and came out dirty. The rims of glasses were not clean. I had several 3 service calls and changed dishwasher soap several times per their suggestions. I contacted Maytag and was told that the only warranty was for mechanical problems and since the problem was not mechanical there was no warranty. I then went through the Better Business Bureau. The ultimate decision from Whirlpool was It has been determined there are no defects with the dishwasher and the issue is use and care. Mrs. **s request for a refund is respectfully denied. I have purchased a new dishwasher which does clean the dishes and the Maytag is sitting in my garage gathering dust.

Maytag WFW7590FW & YWED75HEFW 24 Compact Washer and Dryer: These 2 machines are a lemon and the extended warranty plan was completely disappointed. Both needs maintenance before the 1 year warranty ends. The washer was the worst between the pair. The washer cannot spin the laundry dry. The Home Depot extended warranty plan was not the cost. It takes 2 business day for the service call to call us back. Then a schedule date was 2 days later. The service person complained about not getting authorization to do the work without charging us. He did even showed up for the 3rd call. He did nothing to resolve the issue and said the diagnostics showed there was a load issue, which was not true. A very light load still didnt spin dry. The washer not spinning clothing dry issue has been more than 1 month and is still not resolved. The repair person Dean didnt even re-schedule another date after not showing up today. There is a 90 day policy that we cant request for another repair person to attend to the issue. The dryer also made excessive noise which was caused by a broken attachment that established the drum.

I bought 4 appliances - stove, refrigerator, dishwasher and microwave. Just after 1 year, our dishwasher stopped working. Serviceman said it was the motherboard. I had to talk with a supervisor in customer service to get it covered and found that it was only a switch that was bad. Next, our ice maker overflowed with water, causing damage to our new hardwood floor. Again, I had to talk with a supervisor to get this covered and I did not file a claim for the floor. Then, our stove shut down. Repairman found that a wire was shoved into the top box, causing them to be exposed and shorting out the system. Now 2 years and 4 months, our microwave is not heating and I have to call for service. This was a brand-new kitchen that was remodeled and all appliances were new.I am very disgusted with Maytag products and their attitude of We are sorry, but there is nothing we can do as the warranty has expired. It used to be 3-year warranties for Maytag products until they were bought out. Never will I buy their products again. Have been married 40 years, and our other appliances for 38 years never failed and to find that these products are made in the USA.

We bought this dishwasher on 7/8/2013 which is my wifes birthday and boy was that a mistake in many ways! I had 5 service calls on my Maytag Dishwasher MDB7749SBM1 before it went out of warranty. It has issues with the ribbon cable and controller and the control lights are like a disco on the keypad. Now it gets so hot I cant touch the door when its running. So I have had to turn off the power and go get a new dishwasher next weekend which WILL NOT be a Maytag!

I bought a Neptune Washer in 1999. 6 years later (2005), it started making the 747 landing noise. It was implied that somehow it was our fault, maybe, something from my contractor husbands pocket. After all, it was a Maytag, and surely there could be no design or engineering flaw! (My daughter still has 34-yr.old one.) We were told the repairs would be so expensive. It would be wiser to buy a new one. Foolish me, I bought another Neptune to match my dryer. Of course, now this one has the same bearing problem and again its cheaper to buy a new washer. I am angry and not sure how to proceed. Any washer, but especially a Maytag, should last more than 5 - 6 years. I should not have to buy my 3rd washer in 12 years. And if I do, it certainly wont be a Maytag!

I bought my fridge (Maytag French Door Fridge MFF2258VEW) in September 2009. It took forever to get it and when it was delivered, the door was dented so I had to wait for a new door to be replaced. The fridge stopped cooling just before Thanksgiving 2011. I had to throw out a lot of food. It was the circuit board and that was covered under the warranty. I noticed a couple of months later that the freezer was freezing up again and was worried that the fridge would go out again and in February 2012, they came out again and it turned out that the freezer had been put back incorrectly and the freezer gasket didnt fit right and thus, the freezing up on the circuit board. Now it is May 21, 2012, and I came home for lunch to find the fridge not working again! I cant get anyone out to fix it until Wednesday, the 23rd. Now we are in warm weather and I just went to the store and had a full fridge. I still have the warranty and will for another 14 months. I think if this continues to happen and when the warranty is up, we will have to replace this fridge. I can tell you for sure that it will not be another Maytag! What a piece of junk!

I purchased our washer and dryer together in 2012. Now my washer is making a really bad sound on the spin cycle. I talked to Maytag in Tenn. and they wanted 130.00 just to show up. Plus 300 to 500 for the parts that was needed. Wow. I am retired and on a fix income. I called a local repairman in OkC. After telling him the brand of washer I had, he said he would not come out to fix it because of the money would be expensive. 300 to 500 dollars for parts. He said it would be cheaper for me to purchase a new one. This seems to be a real problem. I talked to Maytag supervisor and she could not wait for me to get off the phone. Nor would she give me her name. Buy Whirlpool!!!!!!!!

We have reported the first time use of New Gas Range using the oven and range top at the same time is impossible because of BURN HAZARD AND the response was soft with no explanations. The range arrived March 26, 2015. We were impressed with first baking only. Family arrived at our vacation home for Easter celebration. Our first meal on Good Friday using both oven and range top was a disaster and the cook was burned on the stainless steel knobs. The oven vents below the knobs were about the temperature of the 380 degree setting of the oven!We rendered the unit unusable and called Maytag customer care department during the late table dinner. I explained on the 45 min call we were having this event and would be all leaving Thursday and their solution was 8 to 10 day shipping of Fake composite stainless looking knobs. These knobs will have to be sent to our Ohio home 500 miles west of the Range location?? If they could ship that day why not overnight??THE SOLUTION OF WEARING OVEN MITTS FOR STOVETOP COOKING IS NOTHING SHORT of silly to conduct meals for our guest. And other members of our family that we permit occasional use of the home open to burns using this Range until we drive 1000 miles round trip to drive the knobs back to NJ from Ohio??? Customer Care fails to listen. We will not be returning until May. To illustrate my concerns about the logistical issues I asked if Maytag would pay for the mileage and tolls for me to replace BURN proof knobs. Oh and will it work or melt? Furthermore who will pay for the takeout needed to feed our family? He did not get it and consulted with supervisors for most of the call therefore 45 min of wasted call. No solution, self installation on an $800 Range. Dissatisfied CUSTOMER with an unusable Gas Range Burn HAZARD!! Poor Design oven vents less than 2 inches below stove knobs! See Photos.

MFI2670XEMS - I bought a Maytag Fridge MFI2670XEMS in 2012. I dont remember how long it took to start leaking but it wasnt long. Same thing as what most people are complaining about - I also have hardwood floors that are ruined. I just had a kitchen remodel and now I wish the floors werent new. Warped badly under the fridge. It is a constant pain. I have to break up the ice with a blunt object to get it out. I was so excited to get a new fridge. Of course it was on sale, now I know why. I wish I had just kept the old one, at least my floors would look great. Lame.

This is March 18, 2021. I bought a Maytag washer, model MHW5630HW2, which is their high end front load washer, in early July, 2020. The machine worked fine except that out of an available 10 cycles, only two would run. The seller, which was Sears, replaced it as defective. The second machine runs all the cycles but, though leveled carefully, it rattles, screeches, walks across the floor and generally seems to be trying to tear itself apart. The repair service replaced the shock absorbers in this new machine, after a six week wait for parts. This did nothing to fix the problem. The repairman finally just said he doesnt know how to fix it. After many patient hours on the phone with Maytag, they have said I have no recourse. The machine is under warranty and I purchased, for an extra $350, a five year warranty. Both warranties are useless. Maytag refuses to stand behind their product. I live in a small town in New Mexico. There is only one repairman. He cant fix it. Sooo...if you live in a small town, or dont want to spend endless fruitless hours with repair people or on the phone with Maytag, who will ultimately tell you they just cant help you, DONT BUY THIS MACHINE.

All my kitchen appliances are from Maytag, however I would highly recommend buying the extended warranty for any appliance you buy. Maytag is not helpful to customers when it comes to repairs. They will recommend you their authorized companies which here in Colorado Springs are the one with the worse review and already knowing the the repair will cost more than the cost of a new one. You will have to be available 5 hours of your day and spend $110 for a guy to come to your house and tell you that the repair will cost more than a new one. Oh and if your microwave is a 2.0 CU like mine you will have to pay $300 plus in double labor because your microwave will require two people to take it down from the kitchen cabinet.

The door is worthless. I am the only washing machine user in my home and am gentle with my appliances. However over normal use, the washers door has cracked and has had to be replaced twice since it was purchased from Home Depot.

The Deli drawer randomly falls, shelves in general do not fit well. Rough edges on door corners are a hazard especially for children. Service call line was extremely poor with a total disregard to customer concerns. It has been a very bad decision!

I saved for this refrigerator for some time and assumed at my age this would be my last one. Thats a joke, less than 2 years and I see this water leaking on my floor. I blamed my dog at first. This was a Home Depot purchase. I love the middle drawer but the freezer has this problem. I removed the ice but it comes back. I did not purchase the extended warranty because if you have an excellent product, you dont need an extended warranty. And of course this happened RIGHT AFTER the warranty ran out. I am VERY upset with Maytag/Whirlpool. Will NEVER buy another product from them. This fridge should not have problems in less than 2 years.

I purchased this machine 6 months ago - have called 2 repair people. Thank God I purchased at Sears with extended warranty, was just replaced. I would tell you if you are looking for a machine run away from this one. It tears clothes, have to wash everything on bulk wash or I would not get enough water to say how bad this washer is. If someone called me and said I won this washer, I would say no thank you. And if I had to say Maytag repair called them, said she not getting enough water. Now this is what they told him: thats how we designed it. Forget about big drum, you cant put blankets or any larger items, goes off balance. And I have to say, if I had the money, I would put to the road and go back to wringer type. So again, do not make my mistake. Do not buy this washer and let me say the second day I made a complaint, was told it take time to get adjusted...NOT. I give this washer a 0.

Bought a new Maytag dishwasher in July 2013. In December it quit working and the problem was the control panel. The service tech knew automatically what the problem was when he arrived. It is now May 2014 and the control panel has gone out again. Contacted Maytag and was told they will extend the warranty another six months from the original warranty. After reading that this has been offered to others with mixed results I have my doubts on whether it will be honored. This is our last Maytag appliance.

I bought a Maytag dishwasher just 15 months ago. Worked fine for the first 12 months. Then literally, a few short weeks after the warranty expired, the buttons on the control panel started acting up. The normal button, when pushed, would light up the delay hours. The light cycle would make the rinse only come to life. It was beyond frustrating. My husband would unplug it to reset it and that worked for two weeks but now, nothing. It wont work at all. Im FURIOUS, considering we spent $450 on this thing and now its useless. I had a Kitchen-Aid that I loved but due to cost, decided to get this hunk of junk. I learned my lesson..Maytag, you should be ashamed you make such horrible products.

Had it for over ten years, had no problems. We dont use the oven too often but it is simple to operate and has served us well. Easy to clean, stainless steel like looks on the front goes well with our other appliances. Reasonably priced too.

The cost was right for the quality of the product. Brand was also a factor. We have had no problems either machine, both work as expected and have fully met our expectations. We recommend these products. Energy efficiency, ease of use and capacity were all considerations in making the selection we made. Maytag continues to hold a good reputation. Regular repairs, low quality construction and a cheap finish which looks tacky and is also difficult to clean would each be deal breakers. We purchased our full-sized, side by side Maytag Neptune Washer and Dryer gently used from a private party who needed to obtain different models due to a remodel of their laundry/utility room. We paid about $600 for the pair.

Maytag Dishwasher control panel is not working again! We have owned dishwasher for less than two years but needed repair twice. This time the warranty has expired. We will not have it repaired again. Its too expensive! We will never go with Maytag again.

Received new washer & dryer on Oct 2nd, 2015. The dryer has been acceptable, but the washer has been one problem after another. First of all the washer is so noisy beyond belief. The engineering is one dreadful design. At first attempted use, washer would not begin cycle. Sensor would say lock, unlock, lock, unlock for so long, I would cancel & begin again. It became such an annoyance that I placed start of cycle on a timer (it sat at sensor mode for 20 min.) then I restarted next time sat for 15 minutes without starting. After beginning from start position it would start OR NOT. First repairmen told me timer might be off a bit. As days passed with same issue, second repairmen arrived and found that door was off (not completely closing). Repairmen would place an order for new seal. Upon repairmen arriving for third time (new seal did not solve issue) he believes that lid is uneven, & he will order a new lid & return in a few days to repair. I must admit that service has been quick, but the issue is still a headache. I would NEVER recommend this model to anyone and would like for Maytag to replace washer with a different model. The noise is a factor that no one should have to endure. The grinding noise can be heard from three rooms away from laundry area with laundry room door closed! Im absolutely a very very unhappy customer.

We had 10 year old Kenmore units in the past that were much better and worked faster at both cleaning and drying. We prefer a washer with a agitator and top load. The dryer is preferred to be gas. Both the Maytag washer and dryer we have need constant repairs. Washer for control panel repairs, and dryer for false heat sensing problems. Now they say not to use dryer anti-wrinkle sheets. The washer needs less sheets put in at a time to rinse better. It is a agitator less model.

I have been washing clothes in different washers for almost 4 decades and never had a terrible washer until now. It has total control of the water level and it NEVER has enough water added. I have to add at least 2 full dish pans of water to every load. My washer does not allow you to pick your level because it does it automatically and no theres way to bypass this problem. It moans and groans for almost an hour in slow motion at its best. It should be illegal to sell such crap!If the intent was to save energy it fails when it runs twice as long as other washers. The instructions that are in the lid say that when you set it on deep water wash that it does not sense automatically-LIES! This lid must be generically made for other washers that they have because again, you cannot choose a water level. When a washer runs for almost an hour (this is not soak or extra rinse either) it is not saving energy over those that run for half that length of time. I wish I had returned it, but I listen to others who say that this is how washers are now. I still owe 150.00 on it and hate writing that check.

I have a stainless steel dishwasher, model MDBH985AWS10. Its about 5 years old. The control panel works intermittently -- Ive replaced and ruled out the door latch -- now Ive got the problem narrowed down to either the control panel or the circuit board. Ive read about this diagnostic cycle I could run to try to help diagnose the problem. I emailed Maytag for the code and waited a week and didnt get a response.I called them today and they said they cant give me the code--they only give that to their technicians. My dishwasher is not brand new, but I paid good money for it, and Id prefer to not have to guess what to buy when Im trying to repair it. Each of these parts costs about $150. Im not sure what the policy is for other dishwasher manufacturers, but for the next washer I buy, Ill find a company that either 1) has more reliable products or 2) at least tries to help the customer repair his own equipment.

Do not buy a Maytag dishwasher with model # MDBH969AWB1. I bought this dishwasher last Dec. 2010. I could not use it for 2 weeks, because the door would not shut. The repair man came & fixed the door. Then when I actually got to use it and after it finished running the cycle, the tub was dripping with water all over--top, sides, door, bottom. I had to dry the dishes on the top rack, and I had to leave the door open for days in order for the inside to eventually get dry. The first thing I noticed about this dishwasher when it was installed was that it was smaller than my other dishwasher. I hate the design because of the way they have made the racks plus because it is smaller--it holds less dishes than my old one did. I could actually get almost twice as many dishes in my old one than I can with this one. Do they not think of asking the consumer about what they want in a dishwasher instead of going ahead and making something that is not functional?I am so frustrated with this thing; it has brought me to tears. I just today went to Sears and looked at their Kenmore dishwasher. It is designed more like my old one than any of the other makes out today. I wish I had checked this out, before I bought this Maytag. Weve always heard how Maytag is at the top of the line with no problems, right? Dont believe it. I will never buy another one. Whoever is designing these dishwashers need to go back to 1990 and take a look at how it was designed and then go back to making them like that. I loved my older dishwasher, and I wish I had never let them take it away. I wish I had taken the money I spent on this ridiculous Maytag and had my old one fixed no matter what the cost. I made a terrible mistake.If you have an older dishwasher and it has given you good service for years, I suggest you have it fixed and keep it, because you will not like the performance of what they are selling today. It does not matter what brand you buy, they are all designed the same. Just take a look and compare them. But if you buy, please check out the Kenmore. I dont know if the performance is better, but the racks are better designed. My old dishwasher was a Hotpoint. It was the cheapest one on the market, and it gave me the most wonderful service ever. The dishes were always very clean, the heating element was fantastic, and it always dried the dishes completely. I cant believe they would make a product like they do today and sell them for what they do. The heating element in them today is not as good or strong as what they used to make. That is why the dishes wont dry properly. You get way less than what you pay for. Thinking a new dishwasher is the way to go, think again. Please, if at all possible, keep your old one and have it fixed over & over again. I hate this dishwasher. What a joke on the unsuspecting buyer.

Having issues with my mothers refrigerator, simple enough huh? She had misplaced my owners manual. NOW you buy the fridge, but like everything else, once they get your money youre basically on your own! I call to have a owners manual sent to her, she doesnt interact with the internet. I mean, there are still your older ones that doesnt even get on a computer. BUT I was told I couldnt get one! But when I bought it, I had one. Instead, I think its ridiculous how once, like any other major company, they get your money, and threw to the wind after that, something as simply as getting an owners manual for my fridge!!!! Last time I do business with MAYTAG!!!

We received a MayTag Microwave on Saturday May 10, 2014. There was a minor ding in its case, but it did not show any other damage. After installation I tried to use the microwave. It did not work. So on Monday the 12th I called 800-688-9900 for service. A service appointment was scheduled for Wed May 14th. The service man told us the microwave could not be fixed and had to be replaced. I asked who should replace it. He told me to take it back to the place of purchase.I took it back to the dealer and after a lot of discussion it turned out that MayTag had to replace it. I was given a case number. I called Maytag and was told replacement could take 4 -3 weeks. I could purchase a new microwave and have it by Friday may 16th much sooner than Maytag could do.

I purchased a French Door, Bottom Freezer refrigerator in the summer of 2006. Less than 3 years later, the ice maker door kept opening and closing and the lights on the door panel kept flashing. I called Maytag and found out there was a problem with the circuit board, and that it was under recall. The refrigerator was fixed at no charge and I was happy. Approximately 2-1/2 months ago, less than 7 years after I bought the fridge, it started getting too cold inside and then too warm and then too cold, etc. Then it stopped cooling altogether. From what I read, it was either a problem with the compressor or the relay on the compressor. There was a recall on the relay on some models, but not on mine. I cant even afford a service call. Let alone a repair charge. If the compressor is the problem, Im looking at a repair bill in the hundreds of dollars. The online price for a compressor is over $300. I dont have the money. So the beautiful refrigerator that I paid $2,000 for sits in the kitchen, unplugged. I never figured that Id pay that kind of money for a refrigerator and have 2 major problems with it in less than 7 years. I just got off the phone with Maytag and, of course, they cant do anything to help me. I was hoping to never buy another refrigerator, but if I have to or if I have to buy any other appliance, I will never ever buy another Maytag or Whirlpool. I will post everywhere I can about my experiences with this refrigerator.

We trusted the Maytag name to give us a good product that would last. After six weeks the Maytag Bravo stopped working. Having to wait 7 days before a service repair person came to our home. The main motherboard needs replaced. So currently, we are still waiting for the part to arrive and have it installed. 2 weeks without a washer after spending 600.00 for a new washer. There is more problems also, this machine takes 1 hour to complete a single load of laundry. Plus it does not get the clothes clean and the rinse cycle does not get all the soap out of the clothes. Very unhappy with the Maytag Commercial Bravo. Will not buy another Maytag product. Save your money and get another brand. We plan to get this one fix and sell it.

I bought a Maytag dishwasher, model # MDB7749AWW1, in April 2011 and the control panel just stopped working. Of course, Im outside the one-year warranty, but judging from the other reviews on this site, that doesnt really matter. A $500 dishwasher should last more than 17 months! I agree with the other consumers. The control panel on these dishwashers should be recalled. Obviously, its defective. Instead, Im being told I can either pay $250 for the repair plus a one-year warranty or $130 plus parts to cover a onetime fix. Ridiculous.

Oven racks falling down and theres appears to be no solution because the interior liner of the oven has warped. The 3rd party repair guys tell me the interior liner needs to be replaced, its not worth the repair cost, Im better off shopping for a new set. Its so unfortunately that this happened (we moved into this house with existing appliances that we cannot use...) and it seems to be a common problem, yet Maytag claims they have NOT received any complaints about this.

Bought a Maytag washer from Lowes 3 years ago and it is just junk. I am 62 years old and never had a washer that actually broke down. What happened to good American technologies. I guess those days are gone, anyway dont buy a Maytag, duh. It is the day after x-mas and I have to buy another machine.

It’s really quiet and it cleans the dishes, pots, glasses on just 1 cycle and I’ve had it loaded more than one time. I do use rinse aid and I do occasionally use dishwasher cleaner. I wouldn’t own angry other than a Maytag dishwasher. They last forever. The commercial about calling a Maytag service man is true! I’ve never had to call fior service! Well worth the money!

I wished I researched more before I purchased, but like most people, I believed in the reputation of Maytag. Like many others - my control panel started to go out 19 months after install: Had my first event with the washer; it would not allow me to select normal wash. A high-end machine shouldnt have electrical connection problems within 19 months, just 7 months after the warranty expires.When the repairman pulled apart our machine, he found a similarly burned looking touchpad ribbon cable, that was burned in exactly the same position as the photos shown on Maytags website under the review referred to. Maytag/Whirlpool has set up a special phone number to deal with this problem: I dialed 1-866-931-7384... Been on hold for over an hour Of course - NO answer! Ill try later but I am very angry that this has been a known issue BEFORE I purchased mine at Home Depot. What a piece of junk. This is the last Maytag Ill ever buy again. The service is horrible, the product is junk.

Perfectly great, cleans anything, not terribly quiet, but results are more than satisfactory. Good water pressure, cleans every nook and cranny, things come out spotless. I do not have anything else to compare, but I think the size is fine, I can put a lot of stuff in it. Controls in front at top, easy to use, clean appearance. Even though my dishwasher is 13 years old, I have not had any trouble with it. The top racks are strong and hold a good bit of glasses, cups and bowls. I have put baking pans, cookware, grates, and a lot of other stuff in to wash and it all came out clean.

I purchased my Bravos washer and dryer in Sept. 2010. What a mistake! The dryer is okay but the washer is a nightmare! The repairman and I are on a first name basis. The last time he was here, he showed me how to recalibrate my washing machine. It stops working in the wash cycle, fills with water and then sits there. I have to manually drain it and start over. Then it gets confused and fills with water when it is supposed to be spinning and draining (consequently draining my well). I shouldnt have to recalibrate anything in life, much less, a brand new washing machine.

We purchased a new Maytag washer and dryer from Home Depot; a couple months later the dryer started to rattle so we contacted Maytag and they sent a service tech out who stated this was normal as the dryer was settling and parts are not as tight as they are when new. This was a garbage response and he was asked to leave. I contact Maytag again, told them of the problem and the tech response and they offered to send another tech out except I would have to pay for the service call since they already sent someone out. I sent them an audio file of the rattle, no reply. Eventually Home Depot ended up replacing the dryer as Maytag refused to help me despite it being in the warranty period.

The oven range (model number mgr8772wb) will not heat to proper temperature. It runs 35 degrees cold even after the built-in adjustment of 30 degrees. the repairman said it was just a cold-natured oven and we had to get used to it. So if a recipe calls for 400 degrees, you must preheat to 430 degrees. As much as this thing cost, it should cook properly. I must rethink Maytags reputation. I thought they were the best. Wrong.

HORRIBLE. Dont pay more for substandard machines. Had a Maytag washer and dryer delivered on March 27th 2018 and it has been a nightmare to get it to start up. Now I have clothes stuck in there. I called Home Depot, you should never buy any appliances from them, they wash their hands of all responsibility once you sign for it. Called Maytag. On hold for almost 10 minutes, they only have 2 certified repairmen in the area 0f 600,000 people. Will be 5 days until they come to look at it. I told them I wanted to return it for a GE or something else. They said I had to contact Home Depot yet Home Depot told me it was Maytags problem. SAVE YOUR MONEY!!! MAYTAG IS NOW AN INFERIOR PRODUCT WITH EXTREMELY INFERIOR SERVICE.

I think it would be nice to state on the box of dishwasher that customer may need a water connecting fitting and hose for their new dishwasher. Yes, I was asked if I needed anything else and I replied I dont think so! Well when I got home, I did need the water supply sweep 90 degree elbow. Or tell sales people to inform there are parts missing. I had to drive back to Huntsville, AL from Hazel Green. Not life or death, just saying! I do like Maytag products. The dishwasher I replaced was17 years old and we had good service! It’s just starting sounding like a rocket motor. Time to upgrade, I thought. Well my wife really thought so! ;)

Purchased model MBF1958XEB4 September 2012. The unit is provided with a bottom freezer. About 2 month age water was forming and freezing on the bottom of the freezer compartment and leaking on the floor. It appears that this is a common design flaw recognized by Maytag with an updated part available that is intended to correct this problem.Contacting the extended warranty company I was informed that this is normal maintenance and not covered under the plan. Liars!! One does not remove a car engine to change the oil. To correct this problem the refrigerator is required to be pulled from the wall, disconnected from power, remove the back lower cover, disconnect two wire cables, replace the drain tube and reverse the process. Normal maintenance - give me a break. The company promoting this phony plan is Federal Warranty Service Corporation in Atlanta, GA. Do not buy a plan from them and if you have one cancel and receive a refund if possible. Maytag get into another business because your product is junk.

We bought the Maytag Aqualift cooktop about a year ago & are continuously dissatisfied with it, for several reasons: 1) the cooktop is a huge nuisance to cook on. The burners are either raging hot (causing boil-overs), or too cool to simmer. The boil-overs then require much cleaning with an expensive cleaning agent. 2) the oven, whether you use regular or convection, underheats - so you can’t tell how long the cooking or baking process will take, & you have to monitor the cooking process. 3) the so-called self-clean is a joke; the oven will not be clean unless you crawl inside & clean it manually. Overall, I’d prefer to toss this range in the trash. I’m a good cook, but I get angry every time I use this expensive, poorly- designed product.

I have had this range (Maytag MER8775AS electric range) for 36 days. The hot surface indicator light doesnt come on (bulb is fine) and the heat elements turn on and off on their own when I am cooking. 36 days! This thing is junk! I am going to see if I can return it, even though it is outside the 30-day window.

Bought DW 2 1/2 years ago. The control panel has a mind of its own, and today it will not even light up. How does a recall happen? I see lots of people having trouble with this model and others as well. A dishwasher should last much longer! Will never buy a Maytag again... and will recommend the same to my friends.

Maytag Dryer is a complete piece of junk. First repair at 13 months, second repair at 15 months. I would throw it away but like a fool I bought the washer. Fingers crossed. Stay away from Maytag, total junk.

I bought the Maytag Bravo XL washer and dryer at Lowe’s on sale spending almost $2000. Loved both of them until the washer stopped with a load of laundry in it. No power to unit. Called for service. Could not provide serial number as locked in washer. Service company able to order parts without the serial number but part put on back order. Washer needs a master board. After 1 week of wet laundry stuck in the washer called store manager at Lowe’s. I contacted Maytag Service and had a rude customer service clerk who finally listened to me after I got angry with her. She contacted the appliance repair company and got the back ordered part sent to the appliance repair company. We are now 10 days out. Still do not have the part; just talked to appliance repair company supervisor. The appliance repair company supervisor said he would schedule installation as soon as he had the part. It will probably be 14 days when I get the washer fixed. I am dreading opening the washer to get the load out that I will have to throw away. When I called for service at Lowe’s the representative said, We have had a lot of issues with this. A 2 month old new washer should not have the control board go out. Shame on Maytag.

We bought a Maytag washer in 1987. It worked beautifully for years. The Maytag Centennial Washer we have now is sub-standard. It takes a full hour or more to wash one load. No quick wash feature. Today I filled the washer with soap, clothes, and pushed the button to fill it. It filled and inexplicably drained, wasting my time, water, and laundry soap. I regret buying this washer.

The machine dries out the clothes so tight that they are full of wrinkles. I am so dissatisfied with this machine, I spent almost $600.00 for this and this is what I get. I also end up with fabric softener all over the clothes. I use the Downy Ball and I just took out my black pants to find blue all over them. I contacted Home Depot where I purchased the machine. They said to get a hold of you. All I want is get a different machine, not an HE. This is beyond anything. Someone should have to put up with, can you help me?

So the reviews for the Bravos MCT online were pretty decent. We purchased our set from Lowes. However, the clothes dont turn over. I watched as long as I could (getting frustrated the longer I watched) to see how the clothes were going to get turned over and washed. All they did was get rubbed on the bottom of the pile where those agitator fins are. But they never got a good flipping so that the top of the pile was washed. I only had 4 normal size towels in there. So it isnt like I had too many clothes.So I called Maytag to tell them what I was observing and the gentlemen explained that it was counter-intuitive technology and that it seems like they wont come clean but he promised me by the time the load was done they would be clean. Yet - they did not come clean! The dirt on the towel was still there on the top of the load with dog hair. NOT TO MENTION SUDS!! Im so disappointed because the burden is on me to either take this set back or deal with it. Buyer beware - if you look at this machine and ask yourself how in the world will the clothes get clean - you are asking a great question! They dont!!

Maytag Top-loading washer MVWP475EWO - I just want to comment on how engineers have made our washing machines worse instead of better. I had to replace my Whirlpool Cabrio washing machine - and did try a new one of that brand, but had the dealer take it back. It had so little water when it ran and was a piece of junk. Anyway, replaced it with the Maytag and it too has the water saving feature (which I understand all of them do) but I have to put it on the bulky setting all the time to even get the water to at least cover the clothes. The clothes just barely, if at all, actually move! They sort of rotate a little at a very slow speed. Boy, maybe this was the time to try a front loader so the clothes at least moved a little in the machine! I am so disappointed in how all the machines are manufactured now. One dealer told me I would like the Speed Queen, but it would take five weeks to get one. Thought this Maytag might do the trick, but now Im stuck with it anyway. It does not spin the clothes out nearly so well as my old Cabrio did. The clothes are pretty wet! So, another fine engineering feature. I wish the engineers would be the ones that actually did some laundry so they would see how bad the machines are. My daughter has three young boys and theres no way this would clean the clothes for her. I told her she should be glad her machine is still working. The dealer was very nice about it when I returned the other one, but it seems all the machines arent really made to clean clothes anymore.

My Husband bought a Maytag Bravos Washer 2 years ago this next month. The washer is extremely hard on clothes. We have to wash all clothes on hand wash to keep them from tearing up our clothes, and we are having to replace the door lock for the third time. Of course the last 2 times were not under warranty. So once again, I cant do laundry when I need to. Thanks.

I bought a Maytag Bravos top loader in Oct 2011. About a yr after having it, it started having problems. At the end of the cycle, theres still water in the tub and clothes are soaked. A couple of months after that, it started completely skipping the wash cycle, so the clothes would just sit in dirty water and do nothing. I called the small appliance co. I bought it from and by the time I get done paying a house call and parts, I might as well buy another one. I called Maytag because it seems theyre all having the same problem and at some point youd think they would be responsible for their product. They couldnt care less and the options they offered me were a joke!! Please, whatever you do, DO NOT BUY A MAYTAG because you will be on your own if anything goes wrong (unless you want to pay them the price of a new washer!!).

We were offered a Maytag microwave with our newly built home two years ago. I do not know if it was a good value for the money compared to other brands as I did not price or feature shop for this oven. But the oven has worked well since we moved in.

This top load machine replaced a top of the line Maytag Neptune. It has five water levels. It has three temperature settings and four wash selections. It also has a selection for an extra rinse that I use for white loads. The washer is very reliable. Clothes come out clean with an average amount of detergent. Although this washer is more than fourteen years old, it has never needed service or repairs. By running a cleaning cycle every six months, it drains like brand new. The stainless steel drum is still as polished as it was when it was new. Even the hoses have lasted with a need for replacement.

We moved into our first house just over two years ago and decided we needed to get a new refrigerator. We did a ton of research online, reading reviews, etc. We found a few not so great complaints regarding Maytag; however, we took our chances. (Note that we live in a house built in the 40s, so the fridge space is small and we needed a fridge size that is smaller than normal. We didnt have many options.) Well, a little less than 12 months later (yes, luckily right before the warranty expired) our ice dispenser stopped working properly. The mini-ice door would not close properly, resulting in a lot of frost in where the ice door was located. (There was so much we couldnt open the freezer door. It would get stuck.) So, we called out the repair guy and he said he had never seen this issue before and basically had to replace the whole flap and parts. Sweet. It was fixed and cost was covered! Well, about 5 months later, it happened again! Ah, they got it fixed yet again. Well, another six months later and after the warranty expired (lucky us), the fridge completely stopped cooling. (And it just happened to be Halloween, not a great day for a house issue.) So, we had to remove all our perishable food and place it in a cooler (which works hundred times better than Maytag products), and move all frozen food to a family members house 15 minutes away (luckily!). We were also super lucky we found a repair company that could come out at 5pm the next day, which happened to be a Friday! Awesome company (Conners Repair in Metro-Detroit). He concluded the defrost board was broken, meaning it was freezing and creating frost and then not defrosting, clogs the vents and not allowing circulation to occur. He was shocked when he found out we only had this fridge for 2 years and said this is something that normally happens in 20-year old fridges. I then decided to call Maytag and nicely requested a refund for the issue. I was told no due to the warranty expiring and also because we didnt use a Maytag repair company. I didnt want to wait a week as I thought this was something that needed immediate attention. I also am not sure why it matters who you get to fix your fridge. I have an invoice for proof of the issue and the repairman even said hed call to verify the issue. I don’t understand why I have to pay for something that was not properly produced, and not to mention the time out of my schedule to deal with Maytags issues. I now know not to buy any Maytag products due to the lack quality. I guess I learned the hard way.

Bought a washer and dryer from Lowes in June of 2016. Have had service on the dryer 3X and washer 1X since. Two person household that uses product a couple times a week. Dryer drum stops rotating / temp control fails / buzzer doesnt work / motor freezes up / washer makes loud banging sound at the end of the cycle every time....sounds like someone is hitting it with a hammer....Today I want a local serviceman to replace the motor but Maytag insists that I have one of their reps come out next Tuesday to examine the product and then go from there. I have been on the phone for 45 minutes trying to get them to pay me $128 for the failed motor that I will send them for inspection. They will not cooperate. They are hiding behind some BS policy. I want to inform you all in case you are contemplating a Maytag purchase. I will not purchase nor will I recommend Maytag to anyone.

Weve had 2 Maytag washers that lasted a combined 41 years. Five years ago we purchased a Bravos XL top load washing machine directly from Whirlpool. Like many other reviews, it is impossible to keep the machine from going out of balance and trying to tear the laundry room apart. I called Maytag and of course they want to make sure the machine is level in at least 3 dimensional space as well as 2 parallel dimensions per String Theory. As far as the 3 dimensions, I assured them I had already thought of this (as an aside, ever try to find any flat metal on one of these machines? Kind of helps when using a level.)So after more exciting conversation, they offered me a Warranty for $437. While trying to control my laughter, I said I could trash the Bravos and buy a new machine for that price. As far as repairing it, it cost $120 for a repairman to grace my door step plus $35 every 15 minutes plus parts -- again, the decision is to trash it and buy a new machine. In case I was too subtle in my comments, I WILL NEVER BUY A WHIRLPOOL PRODUCT AGAIN. Im too frustrated to tell you about my KitchenAid fridge. As much as I detest it, I am forced to join the buy and trash 5 year club . Sometimes the good old days were really better.

We purchased a Maytag 4000 series washer and dryer in October 2011, and within 5 months, the main bearing failed. The Maytag repair person told us it was an inherent issue and to make sure we use HE detergent (We always have.). Maytag advised parts were not available for 3 weeks, so no washer after 5 months of use. The bearing failed a second time after 11 months. Maytag refused to replace the washer and advised it was repairable condition. Now, we have the bearing fail a third time, and Maytag has advised that they would not repair the washer under the extended warranty program. They offered us 75% refund on the washer (So I guess they expect their products to only last 4 years.), which is simply unacceptable. We are now faced with purchasing a new washer, which will not match the dryer; or we have to purchase a washer and dryer of another brand. Maytag has provided pathetic customer support, and their response or lack thereof shows that they simply just dont care about their brand image or the customer.

Had a Maytag Dishwasher that was recalled in 2007 model # DWU9962AAE. I was sent a notice of recall and when I contacted the Maytag staff in the Recall department said that they were sending out a replacement as the unit. Mine was being recalled due to defects in the heater element, which could cause electrical failure and fire. I was pleased they were offering to replace the unit, and within a week or so, a new unit was delivered. This is where the troubles began... the delivery/install person from a local retailer, complained the entire time about having to do this job, was ill-equipped to perform the install, twice he thought he would have to stop as he did not have the correct tools he shared with me. I felt this was odd, if this is the job he did all the time? I asked for a bill of sale or something that would show that this unit had a warranty, and date of install. I was told that in these cases, the local retailer that is contracted to install takes care of all that. I did get the Dishwasher use and care guide, and it seemed like new unit. I had never had a recalled unit of a major appliance. Also since Maytag had my address, phone and email information as they set the install up. I believed the installer. Fast forward to about 2009 and the control panel on the door starts to lose cycles. I decided that since it was just me using the unit and the cycles I used most worked I would not bother with the repair.Fast forward to late October of this year 2015. The dishwasher Maytag model # MDB9601AWW finally does not turn on any longer... I call Sears to have an estimate for repair of the circuit board in the door. I give Sears the model and serial number... and schedule an appointment. The repairman gives me a cost of roughly $600 to replace the circuit board in the door! I tell him no thanks pay $ 59.00 and decide I will buy a new unit... I review many sources such as consumer reports, where it becomes evident that Maytag as a brand is not very reliable. At that point I decide to call Maytag and speak to them about my issues. Two dishwashers in very short order have issues. Also my new unit only had a one year warranty.So much to my surprise when I called Maytag I was informed they did not have any records of my contact information at my current address..? And worse there was a recall on my current dishwasher back in 2010! I was never informed of this, and had used a potentially hazardous appliance for 5 years with no knowledge of this! How could that be though since I was given my current unit by them in 2007. I was very unhappy at this point.... but my disappointment with Maytag was about to deepen.I was also not happy with Sears Home Repair.... They are informed about all product recalls, and had my model and serial number. When those were entered into their computers when I made the appointment and again when the repairman came out and captured that information on my dishwasher himself that should have alerted him to the recall. Not an opportunity to sell me a $ 600 repair that did not even address the defect for the which the recall was issued.So I am now routed to the Maytag recall department.... where all they offer me is a $ 150 coupon for an expensive Maytag dishwasher? So after explaining my situation... and asking the woman I was on the phone with If she would invest $400 or 500 more dollars in Maytag dishwashers, given my experience with 3 failures of their products in two separate units that were not that old? She said she understood. She arranged for her manager Carol to call me the next day at 9:00 am PST. The call never came, and two hours later when I called in they tried to tell me it would be another 24-48 hours before she could return my call? I was now very unhappy. I asked to speak with her supervisor Tim. He too was unavailable, finally after a very long time waiting on hold. I was connected with Amber. I explained again my issues and told Amber that I would like another Maytag Dishwasher to be offered to me..... as this was a very unique set of circumstances... She was willing to let me write letters like this and contact the Consumer Products Safety Commission and lodge a complaint. I am waiting to be contacted by the manager that handles recalls from Maytag. She alleged that they CPSC does not allow the Mfg to assign specific compensation to individuals. That is true....when they are only subject to one failure as part of the recall.... according to the woman I spoke with at the CPSC. However I had not only that complaint; but the circuit board issue and as goodwill gesture to any consumer they (CPSC) have no jurisdiction.... and Maytag could do as they wish. However I doubt anyone but Amber a low level manager, who took it upon herself to make this decision on her own, without even punting to her boss Tim when I shared my story. I just this last weekend bought a new Bosch dishwasher.... and would caution anyone who was considering the purchase of any Maytag appliance of any kind to use my experience as a cautionary tale.

I sent an email to Maytag regarding my Maytag Bravos washer which I purchased two years ago at a cost of $1,100. I have started having problems with the machine last week. I kept getting the UL error code. I called a certified appliance person to come out to find out what was wrong. I do not believe any of the appliance people know what to do for these machines.First, I was told it was the control board that needed to be replaced, then I was told the motor had a crack in it and it needed to be replaced, and then the springs needed to be replaced. So they replaced the springs. This was a Tuesday afternoon. It worked fine until Wednesday of the next week and I started getting the F51 code. Just let me say if you cannot stand behind your parts on a $1,100 washer that is only two years old, then something is very wrong. I am in for $159 on repairs so far. Who knows what the cost will be to finally get the machine repaired.

I was always impressed with the front loading spin washers commonly found in laundromats. The top loading Maytag Bravos does a great job of cleaning clothes and does not stick another door in your way when loading or unloading it.

Disappointing that a Maytag would be a problem machine. Constantly out of balance when spinning and mediocre cleaning. Now it is spitting oil underneath. Am on my way to buy new machine with agitator.

Our experience with our Maytag refrigerator has been anything but good! It has the model # and serial # of the ones that have been recalled, only we have just found out about this. We bought this new at Sears. Soon after, it started having troubles with the freezer, would freeze up and the whole thing would stop working. Over the years, we have had repair after repair, money after money. Just for the record, my husband and I about every two weeks spend about one hour defrosting this monster! It looks nice on the outside.

Maytag Bravos 300 Washer - Dont buy this washer! This expensive washer has been the worst household appliance Ive ever owned. We bought Maytag thinking we were getting the best. NOT SO! We could have spent half the money and got a better washer. Maytag is a brand of the past. Ive had this machine about 4 years and its been a problem since day 1. There is no soak cycle but I knew that from the beginning. The problems Ive had so far are: Not enough water so items dont get wet and have to wash again, Terrible wrinkles, torn sheets and garments, items still dirty, getting louder & louder, and the most recent problem is the plastic from the top edge of the tub is now shredding and getting sharp plastic pieces in my clothes.

Within the first six months the drive on the washer went out. Had to order it from another city cost over 200.00 for it then had it put in. The dryer works most of the time but now and then it just dont dry all the way.