The cost was right for the quality of the product. Brand was also a factor. We have had no problems either machine, both work as expected and have fully met our expectations. We recommend these products. Energy efficiency, ease of use and capacity were all considerations in making the selection we made. Maytag continues to hold a good reputation. Regular repairs, low quality construction and a cheap finish which looks tacky and is also difficult to clean would each be deal breakers. We purchased our full-sized, side by side Maytag Neptune Washer and Dryer gently used from a private party who needed to obtain different models due to a remodel of their laundry/utility room. We paid about $600 for the pair.

Faulty Maytag MDB8969 Dishwasher - BEWARE! Whirlpool, Jenn-Air, Amana, Maytag, KitchenAid... Are all brands that fall under Whirlpool. According to Better Business Bureau statistics there is less than 1 chance in 10 that you will get the Whirlpool product you are expecting! We purchased a new Maytag dishwasher at the end of 2016. Within a couple of weeks the dishwasher began failing: discharge pumps, heating elements, soap dispensers, door leaks, faulty racks, rinsing problems... Since purchasing the machine we have had to make 7 different service calls, all under warranty. The warranty service providers have been good but the machine has been a catastrophe, having been out of commission for several of the 18 months since being installed, and causing serious water damage to our kitchen floor (based on several other negative reviews this leaking is not an uncommon occurrence).A few months into owning the machine, after our 3rd service call, we contacted Whirlpool, Customer Service and asked for the machine to be replaced. They refused to replace the machine but extended our warranty free of charge- better than nothing but not a cure to the problem and the only remedial action that Whirlpool was willing to offer. We didnt understand at that point that the problem of faulty and defective Whirlpool products was probably so huge that Whirlpool could not afford to provide a reasonable solution to their customers; leaving many, as witnessed on various product review sites, to bear the extreme frustration and associated expenses borne from the incurred failures. Unfortunately, here we are once again, requesting our 7th service call in less than 18 months, and asking once again for a replacement.The Whirlpool response this time (CSR was not allowed to let us speak to her Supervisor in spite of trying to negotiate that for several minutes) was that they would not replace the defective machine but would sell us a new $850 machine for $250 and would dispose of the faulty machine for an additional $25. Whirlpool would not however pay for the uninstall of the faulty unit nor the install of the new unit (about $350) which would have to come out of our pocket. We won’t be spending the additional $600 to fix this problem as proposed by Whirlpool; we won’t be installing another Maytag product in our home. We were advised that we could fill out a form if we wanted, to try and claim for the damages which the dishwasher caused to our kitchen floor. The form was never emailed as agreed and now we are just really tired of the whole experience so will simply put this all behind us.Our Whirlpool experience has been extremely stressful and quite expensive. It is clear to us that if an appliance which is averaging a serious failure every 3 months since the first day of installation, does not in the opinion of Whirlpool warrant a full and prompt replacement, or even the direct telephone attention of a Customer Service Supervisor, that the Whirlpool quality standard must be so low, the failure frequencies so high, that the number of similar failures prohibits any commercial viability to manage the problems in a reputable manner. Whirlpool clearly has some very large problems. It would not have been easy to destroy the once highly respected Maytag name. Such degradation could only take place as a result of continuous and ongoing Whirlpool quality degradation. We will no longer be their ‘crash test dummies’ but I do hope for the sake of Whirlpool (apparently North American made) that they take ownership of their poor quality condition, realign and spend the next few years becoming the company that we all once knew and respected.

Echoing the sentiments of others on this site, I am deeply disappointed in Maytag brand appliances manufactured by the Whirlpool Corp. When, for the first time in my life, I was able to buy all brand new kitchen appliances, I didnt even consider any other brand but Maytag. This was based on many decades of using Maytag products and watching my mother use them. I come from a big family so our appliances got used hard, and the Maytag brand ones worked year after year, decade after decade with little or no maintenance. To put it quite frankly, my new Maytag products are junk. I could supply a whole laundry list of problems but, in the interest of space, will just tell about the latest. A couple of weeks ago the fake tin foil paint on my oven and burner knobs just started falling off, revealing cheap plastic underneath. When I called Maytag to complain, I was asked how I clean the knobs. I told them that when I clean the stove front I remove the knobs and drop them in warm water with a couple drops of Dawn dishwashing liquid for the few minutes it takes to clean and polish the stove front, and that I had been using this same procedure for 2 years. The rep. hemmed and hawed awhile and then went away to consult her database. When she returned she told me that one is not allowed to soak the knobs per the manual, and therefore she could not offer any help. She then generously offered to transfer me to the parts department, where the rep. informed me that replacements would cost $70 EACH, thats a total of $350 plus shipping for 5 cheap plastic knobs. WOW! What a deal! I tell everyone I meet NOT to buy any Maytag branded product, and to apply extreme skepticism before considering any Whirlpool product. (BTW - the last certified Maytag appliance repairman to come & fix one of the appliances essentially admitted they are junk.) Model #: MGR8775AS SN: R32810432.

We purchased a Maytag washer model MVWC400XWO almost 2 years ago and it has problems with the bearings and the whole computer board is defective. I was told to buy the extended warranty for $350, which we did. As of today, we were told by extended warranty they are refunding our money because there are so many things wrong with this washer, including the whole computer board, that it would cost them too much to fix or replace it. Im in complete shock. We paid well over $500 and are still making payments on it. I spent the day reading hundreds of reviews from people with these exact same problems and Maytag is aware of it and will not help. They should not be selling these anymore. Im completely sick to my stomach. I cant afford another washer and when I called Maytag, they said it was past the year and we are out of luck. I cant believe this can happen to people and they get away with it. A washer should last longer than 2 yrs.There are hundreds of people going through this with Maytag and no one will help.

Purchased less than a year ago, Machine stopped working. Approved service company says no error codes visible must be ok. Machine still does not work month later, service again does not show up for call, following month same. Its still in warranty but they claim it is fine. Error code disappear right after popping-up no storage of error codes.. I had to buy small washer to manage home. Really bad choice of product. Will not use this brand again.

I purchased a Maytag commercial residential washer in late 2018, supposed to have a warranty for at least 5 years. We are in California and I was told that there was only one facility that could come two weeks later. I removed the front panel to have it ready for service tech, who on the first visit kept saying he did not know what the problem was, and left telling me he would order parts. After Christmas, I could not get in touch with service so again called Maytag. Service was supposed to come out on the 30th.After waiting almost 3 hours, he called to tell me he did not have the parts. Also, this repair tech treated me very bad since I removed the front panel which I thought I was being nice. He called me back on the 30th, said someone gave him a part, and came. All he did was remove control panel, lost the start button and told me it worked without checking it at all. He was rushing to another appointment so I tried to start it and it still had the original issue, which was slow agitator and a rubbing/grinding sound. Now, after he did something with control panel it had a clicking sound. I immediately called corporate and was told when he came back, which has now been over a month with no washer, that he would be with a senior technician.January 5th I waited all afternoon and he called and said he was not coming and that my whole washer would have to be rebuilt. He never replaced the parts on previous invoices I received, and I filed a complaint with the BBB. Now they are completely lying. Technician trying to say I had the control panel apart which is not true, and does not match up with the invoices I received. They are telling me my warranty is voided! Its been a month and a half. I was treated rudely from the beginning and now I am obviously being retaliated against. I have 3 kids, two with severe medical problems and have put so many hours into calling with all these issues.I had another service place come out and he removed the agitator and the transmission shaft/drive motor is rusted out, as well as the parts he said he replaced are worn and definitely not new. For this company to come back after all this time and say I did this, when I have the original invoice that clearly states otherwise is absolutely the worst service ever.I bought this machine thinking it would last, and now have to deal with all this. I have nerve damage and it is very difficult to take all the laundry for a family of 5 to do at laundromat. They refused to send someone else out, where they could easily have seen this repair tech never did what he said, and was unable to diagnose and fix the issue. Its appalling to me that this is how they treat customers. Laura ** at corporate is the one saying warranty is voided. The machine looks brand new as it has always been taken care of. They should be ashamed of themselves. Apparently, this is the standard a lot of times with people trying to get things serviced under a Manufacturer warranty!

I PURCHASED A WALL OVEN ABOUT 4 months ago. Used the self cleaning, oven blew fuse and some other part, had to wait for almost 2 weeks for repair because of self cleaning liner is now peeling and leaving fine particles. Maytag said it was ok, they would not replace, the liner doesnt have a replacement part so Im going to have to buy a new oven to feel safe for my family meal.

I have not found one feature that impresses me. Clothes do not always get clean (folds of debris). They do not spin dry enough. The cycle choices are ridiculously complicated. You cant add any clothes once the load has started. You have to wash the machine on a regular basis at about $3 per month. To get more water in the machine, you have to elect the Bulky cycle. Small amounts of bleach is so concentrated that clothing elastic is deteriorating and small holes may appear.The clothing most often comes out of the machine like twisted up tangled donuts. The cycles take about an hour and no longer match up to the dryer time - more trips up and down per load. The cycle guide is way too complicated - Normal Heavy, Heavy Duty Regular - whats the difference? Two service calls tell me there is nothing wrong with the machine - get used to it. I would much prefer the old agitator machine.

My husband and I purchased a new Maytag dishwasher in March of 2012 at a cost of around $650. There is only the two of us at home and I only run the dishwasher 2-3 times per week. On June 16th, I went to run the dishwasher and it would not turn on after hitting the start button. The cycle buttons lit up but the dishwasher would not start. I called the service number in the user instruction manual and talked to a service representative. I was told that the electronic panel that runs the dishwasher is not covered under the 2nd-10th year limited warranty. It would cost around $291 to fix including parts and labor. When I asked for a qualified Maytag repair service company in my area, she only had one company to give me. This company does not have a very good local reputation so I preferred not to use it. My question is - How can a part that runs the dishwasher not be covered under the warranty? If the start button on the control panel is defective then the machine will not work. I also have a model MDB7749AWW2. After reading some of the 356 complaints about this very dishwasher, I think the Maytag Company must be well aware that there is a problem with this machines control panel and they are choosing to disregard the customer. My old dishwasher was a Kenmore and it ran for 27 years and I only had to replace the motor once. I will not be buying anything Maytag in the future.

We bought the Maytag 2000 series washer and dryer stackable set in 2012 from Home Depot. My husband was smart enough to buy an extended warranty and year after year we renewed it. Guess what?? Year after year the dang washer broke. This machine was a nightmare! Now that the drum spider is broken they will not honor our warranty but want to give us $300 and guess what? I cant find a replacement for my good working dryer. We bought this set because we live in tiny space and needed them stacked. Maytag really put us in a corner and we have no money to replace both appliances. Horrible customer service. Horrible machines. Just a horrible situation. We dont know what to do.

Discovered that thousands of others are having problems with the control panel on their dishwasher. Mine is Model # MDB7749SBM2. Looks as if I should just junk this horrible product and buy a new one (another brand, of course). My biggest concern is that I purchased other Maytag products along with this dishwasher, ie, a refrigerator-freezer, a built-in stove top/oven and a microwave. I have had a service call on the fridge (water line), the oven (gas) will indicate a set temperature (400 degrees for example) sometimes it will only be abt 200 degrees via a portable thermometer... Sometimes it doesnt ignite at all (have to reset it 3 or 4 times, the microwave has issues with the digital readouts, and on and on and on.I have only had these appliances about two years (after warranty expired) when each unit started exhibiting problems. I paid $175 for the fridge repair and am now considering biting the bullet & replacing everything as MAYTAG/WHIRLPOOL apparently isnt going to take responsibility for any defect on ANY OF THEIR PRODUCTS! Im 75 years of age, retired and cannot afford the replacement route but it looks like I dont have a choice unless someone has a better suggestion. I dont have the skills or energy to attempt the repairs myself.

I installed a new Maytag Wall Oven Microwave Combo 18 months ago. I had not used the microwave in over a week. Last night, we heard a loud pop and realized the beauty glass front on the microwave had shattered. No one had closed the door too hard, in fact, we had not used it. I see where others have had this problem.

What a disappointment. I guess this is why we no longer see that commercial about the Maytag repairman being bored. Because now, he is out fixing these pieces of shirt. Im trying to fix my washer (Model: MAH8700AWW), what a sweet pain in the **. Dont do it. Throw it away if it starts making noise like an aircraft landing.

I specifically bought the washer because it has an agitator and you have a setting for more water if you need it. My previous washer had no agitation and really miss that. Seemed like clothes got cleaner. On this machine the agitator is certainly helpful, but there is so little water sometimes I find a pair of jeans with dry spots when load is complete. No, I do not overload the machine. If I change the setting to add more water I don’t see a difference in the amount of water that comes in. I find myself frequently adding an extra rinse. I feel that while making the new washing machines eco friendly they have cut back on water conservancy too much. At the very least the consumer should have more options as to levels of water. I would not buy this brand again.

I have just inquired on this site about problems with Maytag dishwashers. Ours does not start. It is about a year old and is Model MDBH989AW03. I am very discouraged after reading the many continual problems with control panels. I am checking my warranty. If it is out of warranty, we think that we will purchase a GE that has worked great in our other house.

I have owned three different Maytag washer/dryer sets. The reason for so many? Selling the set with the house upon moving. I kept my last set which is Bravo. I love Maytag for their features, their dependability, their reputation. I have never had repairs on any of them. Totally awesome! My second set had a neat feature of a drying rack where you could place a sweater or shoes and no tumbling. Sorry I sold that set w/ the house. I am very pleased w/ my present set of Bravo. No agitator. A coworker also bought this set. Maytag is the best!

I spent more than I should to buy this machine but thought of it as an investment to help conserve water and energy. Wrong!! One small load of undies will wash for 60-70 minutes, then still not be clean. So, I rewash them. Really, how does that save anything? I HATE this machine. Ive never seen a washing machine that will wash in WRINKLES! Lastly, I do not like the fact that I have no control over water level. I had one load of towels that the towel on top actually came out of the washing machine with more than half of the towel still dry. Not good! Save your money and buy a machine with an agitator. They simply clean better.

My mother always said Maytags were the best but I never bought a washer and dryer until about 5 years ago and both are the worst appliances I have ever owned. The washer has rust all over the bleach container and smells to high heaven and I clean it with Affresh all the time. The dryer doesnt dry well and the washer doesnt wash well. I am trashing both and buying some new ones.

Maytag #mbl2258es1 - started leaking in the freezer two years after I bought it. Two service men who did not know how to fix it. Now the refrigerator is not cooling. No more Maytags. Horrible refrigerator.

Control panel is defective on my Maytag dishwasher. Found a phone number that was created to deal with this problem. I only had to hold for a few minutes but the first person I spoke to was rude and unhelpful so I asked to speak to someone else. When another agent came on the line I told her that only the normal and rinse button light up but do nothing when pressed. She arranged for a repairman to come to my house and determine if my control panel is defective at their cost. When he arrived he asked me what the problem was and I said, The touch pad control panel is not working. He stated, Your control panel needs to be replaced. I have to order the part and come back to fix it. He was there for about five minutes and he never laid a finger on the dishwasher. When I asked if the control panel design has been fixed he said, No, you will probably have to replace it again.There is a video on the internet that shows how to seal the electronics with silicone. The repairman said that they cannot seal the electronics unless Whirlpool provides a kit to do it. I guess the Maytag repairmen may have to come out of retirement. My husband will seal ours after it is replaced so we hopefully dont have to deal with this problem again. So now I am waiting to see if he returns in a reasonable time frame and gets my dishwasher going. There is a class action suit about this issue filed in 2013 about this defect.Updated on 09/23/2015: A repairman came to my home on August 20, 2015, at Whirlpools cost, and he determined my touch pad did not work. He informed me that Maytag would provide the part, free of charge, but it would cost me 85.00 for them to come back and install it in 2-3 days. As of today I am still waiting for the part to come in, apparently due to high demand Maytag was out of touch pads, which were out of stock. No idea of when that would be, the repairmans company said, dont call us, we will call you when the part arrives. So I began to look for the part myself, found a couple on an auction site, but most companies that sold parts were on backorder. Until I found a company that said their inventory was out of stock but they had five, stashed in the back. The price of 105.00 was not that much more than the 85.00 cost for the service call. Got it in two (2) days, installed (in about five minutes), sealed by my husband and I loaded it and washed my dishes. I was so overcome with relief, tears came to my eyes and I almost fell out. I give five star to the fella that had the part stashed until I needed it.The Maytag repairman is still waiting for the part so he can fix my dishwasher.

I have always thought of Maytag being the quality manufacturer of appliance products. We purchased a Maytag microwave (MMV4205DH-1) and after just two years it has begun to give us grief (we are in our early 70s, no family at home, so appliance receives medium usage). We constantly get the open/door message when we are trying to set the timer for operation. We open and close, open and close, etc. Just yesterday my wife noticed a slight crack on the door just below the handle, most likely due to frequent open and closing. Went online and read a number of reviews and found many others have had same or similar issues. Done with Maytag.

I have trusted Maytag for many years, more than 60 years, my parents and then myself. My Dad always told me I could trust Maytag over any other brand and that has always been true until I bought a new Centennial Econoserve Washer. This is without question the worst machine ever made. I should have asked every question in the book concerning this machine but, oh no, I just trusted the name MAYTAG. I am so sorry. I cant trust it to clean anything that shows it needs cleaning so you have to wonder what does it clean that you cant see. Im sorry people, I just dont know what to do. I cant afford to buy a new machine and the store I purchased are basically telling me, Sorry, you bought a stripped down model. Too bad! I will never buy another appliance from that store nor will I recommend them to anyone. Too bad since they are locally owned. Anyway, Maytag, you blew it badly to turn out this terrible machine. Thats my story and Im sticking to it. Better product next time.

In July 2012 I purchased a Maytag BTM standard door refrigerator from Home Depot. Approx. 2 weeks from the 1 yr. Standard warranty July 2013, my refrigerator started cycling like every 20 minutes and loud popping noises started occurring. 1st service tech would only stay 15 minutes & did not want to stick around to hear the noise. Ran the standard tests and said everything was fine. That was around Aug. 2013. So I put up with it for a few more months and finally the popping noise was getting louder. 2nd service guy (Jan. 24, 2014) got to hear my video recording of the refrigerator cycling and loud popping noise. He replaced a bad dul part (Note: they all wanted to blame it on our ice maker that we never ever hooked up). Oops...wrong diagnosis. Whatever he replaced stopped the constant cycling pattern but now the popping noise is getting even louder like a shotgun going off. 3rd repair guy (Feb. 20, 2014) tells us that is normal and recycle product material is not that good nowadays?? I pay a $1000.00 for a noisy refrigerator and they say it is a normal sound. I dont think so. The refrigerator is now popping so hard that the right side of my refrigerator that faces the open is now buckling due to the compression of the heating and cooling which is causing the loud popping noise. If you rub your hand down the side of refrigerator you can feel the waves forming on the side of the refrigerator. Trying to get a Maytag rep out here. Something needs to be done about the production of these bad appliances.

Maytag Bravos XL MCT (Disposable). Model number MVWB835DW3 Top load washer. I’ve read many of the reviews on the site and feel your frustrations. Let me start by saying, at least you have a choice of products. I’m stationed in Okinawa Japan and have ONE place to buy my appliances and a choice of two machines. Both of them are garbage Maytag products. The first one (model noted above) died after 18 months. NOTHING they could do! The “technician” they sent didn’t have a clue. His answer was to replace the control board. Time to receive part? Up to 30 days. Really! My option? Buy the exact same product. I can’t even describe how screwed over I feel.

A pure piece of junk this wash machine is. It is more of a merry go round than a wash machine. I do not understand how it can be called energy efficient. All it does is spin and spin and clothes come out as beautifully dirty as they were loaded. If you make the mistake of putting a few extra clothes (machine calls itself a large capacity), clothes bunch up and one has to pull them apart. The bleach dispenser was used as one would use a bleach dispenser. However it is all rusted. I had bought extended warranty from Lowes but Lowes did not honor the warranty saying rust was a cosmetic issue. Yet when Lowes sold the extended warranty, they did not specify cosmetics were not covered. It is not even cosmetic. It simply is cheap enamel paint.I have used 200 dollar wash machines but never have I experienced such a horrible and annoying product. I will try one more time to see if Maytag will help out with the rust issue. If not, I will simply cut my losses and buy a regular cheap machine. Maytag should be ashamed of itself. I bought a Maytag because I thought they made the best machines!!! Oh! Well, maybe they did at one time.

I am renting to own a Maytag refrigerator and it is leaking water on my floor. Runt my floor already - had to replace the floor once. Sent it back to the place where I got it for them to fix it. Paying insurance by the way that isnt worth a crap either cause they wanting to tell me that I left it open at some point or the lights was off at some point. Anyway to make a long story short they gave me the run around and didnt want to fix it. But how do you fight big companies? This was a rental company by the way rent to own so now I have 4 payments left out of 24 at 180.00 each and they still dont want to fix it. I dont know who to be madder at - the rental company or Maytag from selling this piece of junk. But by me renting to own it if any problems occurred they were suppose to fix it. Youre already paying twice the amount to get one cause of credit issues. But thats no reason to double screw someone or should I say triple cause you getting doubled the rental company alone. They need to recall this refrigerator. It has been a lot of complaint and they want to tell you to go behind the refrigerator unstop a line. Well I didnt buy this refrigerator to have to work on pulling it out from the wall every two days to do this procedure. This is crazy. Any one out there looking to buy a refrigerator my advice to you would be do your research and stay away from rental places whatever you do because you will pay twice the amount and they wont stand behind their promise either to fix it as long as you renting from them! And stay away from Maytag!!!

I have bought Maytag products for years. I have a white Maytag microwave that is about 3 years old. It was given to me at 1 yr. old by my sister-in-law when she decided to splurge and create her dream kitchen and went with stainless. The door handle broke in the first year. We glued it. It just recently completely fell off completely-snapping at both ends. I am calling Maytag and attempting to have it repaired. I am otherwise very pleased with this appliance. I have had other microwaves for many years without this happening. Im hoping they will agree to repair.

Same problem as all the others, the dishwasher stopped working. The dishwasher is less than three years old; for a two-adult household. The control panel just stopped getting power. After multiple calls to Whirlpool/Maytag, all they will do for me is document my complaint. Im now out $167 to get this thing running with no guarantee that it wont happen again, as well as the fact that this should not have happened in the first place. I didnt misuse my dishwasher. It just stopped! I think there needs to be a class action lawsuit since the manufacturer will not stand behind this obvious defect.

I purchased a Maytag Bravos 5 months ago. I had trouble at first with unbalanced loads. The repair man came to look at it twice. One thing that can unbalance your loads is if small pieces of laundry such as a sock gets outside the basket. Sometimes the basket has to be taken all the way out because small pieces can be lodged under the basket. This happens when you fill the machine too full and those small pieces float to the top.The suspension on my machine ended up needing to be replaced. I have read lots of reviews about soap rings in the clothes. That happens from using too much soap. Make sure you are using HE detergent for one. I cut way back on my soap and my laundry gets clean and no problems with residual soap on my clothes. I was very unhappy with my machine at first but now I absolutely love it!

I bought the power wash Bravos XL... Bad. It does not rinse the clothes, leaves residue on dark clothes.. probably all clothes - cant tell on lighter colors. I dont recommend!!! Waste of money.

Maytag Bravos XL MVWB980BGO. To start, I live on an acreage so some problems may be related to being on well water. The most annoying part is the washer doesn’t have a drain & spin without rinse. So, when my well pump started acting up, I had no way to just drain & spin off the load, so I had to try to lift thoroughly soaked clothes and try to dry them...which took about four hours. Another aspect that is a pain is uneven loads. It keeps trying to fill, instead of just stopping & letting me adjust the load myself. Then the damn thing won’t reset. I often have to resort to unplugging the machine and starting over. High efficiency is a joke. I’ve had the machine about five years now and it goes low flow error, even though the flow is fine. I’ve tried running cleaners through the water line and it’s still doing the same thing. The only thing left to try is take the machine out and try and manually go through the lines. For the amount of money we spent on this machine, I am thoroughly disgusted with how it runs. It is the first & last Maytag washer that I will ever buy. Next time, I’m buying as cheap & basic a machine as I can buy. On the upside, the dryer works perfectly.

I purchased this range from a Maytag outlet in Nov. 2006. No problems with it until Nov 2015. The oven igniter failed. This was serviced locally and replaced in an efficient manner by the local service tech. All is good until 2 days later when I decided it is time for an oven cleaning cycle. I set the cycle for Medium Soil (3hrs). After the conclusion of the clean cycle, the oven (bake) would not work. Called Maytag service, the service tech replaced burned up oven wiring as well as the igniter again. However, the cleaning cycle had taken out the gas safety valve control as well. I am now told there is no replacement oven gas safety valve unit available anywhere. I even called Maytags 1-800 number and searched online only to find the part on backorder and not available.I find this particularly frustrating in light that I spent over $1200 on a Maytag product I thought would bring way more than 9 years of service before it is deemed unrepairable. The average gas range lifetime is 18 years. In my opinion, not a good return for the investment. Its a shame because the rest of the range works and looks fine, which is now destined for the dump. I am replacing the Maytag with a $550. Frigidaire with manual cleaning. Will never buy another Maytag appliance or a self cleaning oven again. If the self cleaning feature has the potential to fry the controls, why would they offer such a feature, or why couldnt they warn one of the potential failure.

I started hearing the Maytag Microwave MMV4203DW00 beeping this morning after breakfast. I had not used it since the night before to heat up soup in a Corning Ware bowl. Its doing that 5E thing and nothing on the control panel works. Ive unplugged it, waited, plugged it back in and the same thing. It starts off saying Select Clock and 5E and then stops on the 5E. I bought this in Aug. 2010 and it is vented out the wall. Of course, that doesnt work now. The metal rack has never been put in it. Im single and the only one who uses it and I dont use it very much either. And this model only got the one 40-watt regular bulb over the range - lousy. And it doesnt work now either. And the control panel lights up orange. Had I known that, I would have never bought it in the first place. Of course, the stupid orange 5E lights up. Im unplugging it for good. Its not worth fixing. Do not buy this microwave!

We purchased this terrible machine 2 years ago. The clothes come out worse than when they went in! White powdery stuff all over darks! I always have to wipe all dark pants down with a wet cloth! Absolute junk! Really bad product! Never buying from this company again!

I bought a new Maytag washer 1 year ago. It does not do a good job of washing the clothes. I have tried to contact customer service but what a waste of time that has been. I would never buy another MAYTAG washer again. This is after owning an older style Maytag for 25 years that I never had one problem with until it wore out. They are now junk. I bought at Leons. Would be very careful of buying there again as they were also no help with this washer not working properly.

I am grateful I dont have to beat my clothes on a rock. Absolutely the worst dryer Ive ever had!!! Previous Kenmore washer was my favorite! This Maytag does not allow me options to stop, soak & freely open & close as I choose. Even my adult children who occasionally use it say its the worst!

I got a new washer and dryer for my ex wife and son last August. Its October and the agitator broke off. She is not abusive to things and just the two of them dont produce much laundry. This was just poorly built. Maytag should be ashamed to have built such a poor product. I thought GE had the worst appliances, but Maytag must have hired their engineers. I have pictures and it has 10 year warranty right on the lid, lol. Should be 10 months,

I have had this refrigerator for less than 3 years. It recently started leaking water on the floor and all over the bottom of the freezer. Repairman said it is a flaw with the defrost drain design. He thinks Maytag MIGHT have changed it since I purchased mine, but I dont know. Originally they used this small rubber valve;repairman said they get clogged very easily (even though I vacuum around it regularly and dont have any pets). He replaced that part with something sturdy that looks like a p trap. I looked online and there are loads of complaints about this exact issue with the defrost drain clogging. It cost $250 to have it repaired. I called Maytag to ask to be reimbursed and of course they will not do anything since it is out of warranty. Its a shame Maytag wont stand behind their products. Since there are so many of us with this issue, cant something be done?

Approx. 3 year old Maytag Dishwasher Control Panel lights blinking with Dishwasher inoperable. Repair part (new Control Panel) costs approx. $180 plus tax. When you add the cost of a service repairman you are nearly at the price of a new dishwasher. I am completely unhappy with this Maytag Product and will never buy another Maytag Product again.

I have a 7-year -old Maytag dishwasher, which was not working well. I paid over $600 for extra features. Maytag contacted me that the coil had to be replaced. They sent it to me, but the repair service said that theyve sent the wrong one. When they sent the second one, the repair service came out and called Maytag, They said that my model cannot be recalled. The repair service left, and after 1/2 hour later, Maytag called me and said that the repair man has to come back and install a new coil. He came back and installed it.

Purchased the Maytag Bravos upon recommendations from Lowes and Home Depot to replace a 20-year Kenmore that finally died. Since the Maytag brand was always considered to be the top of the line washers, we purchased the pair. About a week ago during the spin cycle I thought that a 747 was taking off in our laundry room. Called a local appliance repair service who said that there had been numerous issues with the Bravos series and to call Maytag to inquire about a recall. After 45 minutes on the phone with a very sweet naive young lady, she told me that the new models did indeed have a 10-year limited warranty on parts. However my 3-1/2 year old washer was not grandfathered into the warranty. I could (a) pay the $150 service charge to have someone come to inspect it or (b) buy a new one. I will be purchasing a new one but it will not be a Maytag or Whirlpool product. Now we know why the commercial for the Maytag repairman is not running... Hes now very busy working on their broken products.

I purchased a Maytag Bravo washer and dryer in 2008. I had a repair person out today on both units. I was told that it will cost as much to fix the washer as it would be to purchase a new one. As far as the dryer was concerned, I was told to live with the timer issue rather than replace the expensive mother board. I was also told that the drum bearing issue with the washer is fairly common with the Maytag machines. It looks like the Maytag repairman isnt so lonely anymore! I paid a lot of money for these machines and they amount to a hill of garbage after three years. I may be buying a new washer, but you can bet your boots it wont be Maytag/Whirlpool!

Maytag Appliances - biggest rip off ever! Home Depot needs to stop carrying Maytag appliances. I purchased a Maytag washer Type 832-A, Model number MHWE200XW00, Serial number HL11990545 in May, 2011 from Home Depot. After just three years it flooded my laundry room. Home Depot couldnt help me, and Maytag Customer Service tried to really rip me off.I called Home Depot, asked why they continued to carry a product they knew had terrible complaints and all they could tell me was they are sorry I am unhappy with my washer, then gave me Maytags customer service number. I called Maytag - first the guy tried to sell me a $400 extended warranty package - total rip off. Maytag should be ashamed, then said he couldnt help because it was past the time period. There is no telling how many people they are ripping off with that little deal. Consumer Affairs should be all over this. So then he offered to get a Maytag repairman to come to my house, but couldnt tell me how much the diagnostic visit would cost or anything else. He was worthless.I hired a local repair person to come to my home, the part is $140, its the tub seal, weak and flimsy - has a giant hole. I only wash clothes and towels, nothing else. My local guy is cutting me a deal on the labor, still going to be $200. Maytag isnt what they used to be and I will never, ever purchase another product from them again, ever. And I would suggest you dont either. Maytag appliances only last a couple years at the most, and its customer service is horrid.

I purchased my Maytag Centennial Commercial Technology MVWC200XW in May 2012. This is the second time in almost 3 years that it breaks down. The basket decided to drop today and by the time I realized that it did, my whole bathroom had flooded, the water spread down the hall into my spare bedroom and soaked through the floor, also flooding my basement. I called customer service. They are sending a repair man next week, but as for all my ceramic tiles that are now cracked in my bathroom and my hardwood in the hall and bedroom that is full of water and are lifting off the ground. Its my responsibility to call my insurances to fix it. Yet it was their washing machine that caused the damage in the first place. When I purchased the washer I didnt expect to have to repair it every year. Not impressed! I do not recommend this washer.

We purchased a Maytag Gemini with serial number D40941338 and model number MGR6875AD826. It has been a complete disaster. The control panel keeps breaking down, and its now going to be replaced for the 6th time. I have asked for a new stove when I called the Maytag Extended Warranty Department, and they will not replace this defective product. Please help me.

Purchased model MBF1958XEB4 September 2012. The unit is provided with a bottom freezer. About 2 month age water was forming and freezing on the bottom of the freezer compartment and leaking on the floor. It appears that this is a common design flaw recognized by Maytag with an updated part available that is intended to correct this problem.Contacting the extended warranty company I was informed that this is normal maintenance and not covered under the plan. Liars!! One does not remove a car engine to change the oil. To correct this problem the refrigerator is required to be pulled from the wall, disconnected from power, remove the back lower cover, disconnect two wire cables, replace the drain tube and reverse the process. Normal maintenance - give me a break. The company promoting this phony plan is Federal Warranty Service Corporation in Atlanta, GA. Do not buy a plan from them and if you have one cancel and receive a refund if possible. Maytag get into another business because your product is junk.

Like so many others, I now discover, we are having a ridiculously frustrating problem with our Maytag dishwasher, bought one and a half years ago. Last week, the control panel stopped working -- we press normal and a whole bunch of other lights come on; try to press other cleaning options and entirely different ones light up again. Sometimes we can get it, with luck, to quick wash or super clean and thus have our dishes cleaned (which the machine never did that effectively anyway); sometimes we cant. I havent called the company yet, but given what Ive read, Im unsure if it would do any good. Judging from all the similar comments, Maytag is clearly selling a radically inferior product and care nothing much about this. We will surely never, ever buy another one of their products.

MDBH979SAM0 - Bought this dishwasher from Home Depot 2 years ago and have taken care of it, never abused it or anything. All of a sudden it just starts freaking out, once you start a cycle it will wash and then rewash and then keep going costing us money on electricity, water and wear and tear on the machine. Ive tried everything but it seems like its just stuck in start mode. The indicator lights on the panel flip out too, they will all blink randomly. So when I close the dishwasher and dont intend to start any cycles and it is off it will start up all on its own so Ive had to unplug it. Funny how I called to order a control panel part and its on back order... Very interesting how they are out of this part probably because everyones ordering it.

I recently purchased a Maytag washer and dryer from Lowes. The performance of the washer was highly unsatisfactory. The water sensor does not allow sufficient water to enter the machine. Thinking it was a malfunctioning machine, I spoke to Lowes, and ask them to swap it out with another machine. They were cooperative and pleasant to deal with however, the replacement machine was no improvement. The water sensor does not allow enough water to enter the machine to even begin to saturate the load of laundry! I bought a washing machine, not a dry cleaning machine, but a dry machine was what I got and that is NOT okay with me. The literature states that load will not be covered with water, so that is how it is designed to work. With inferior water levels, and no agitator, there is not even a chance of water splash saturating and cleaning clothes. I am not an engineer, but common sense says this is efficient nonsense. VERY, VERY DISSATISFIED!

When I went to use this machine (maytag bravos). I noticed there was like a 1/4 filled in tub, checked water flow, that was fine. Then read the manual that Maytag sees using Less Water is better for clothes, I always thought it was less detergent, ohh well. Wouldnt recommend this item to anyone.

We purchased our Maytag dishwasher less than a year ago and are very disappointed with the poorly designed quality of this product. We had a Maytag repairman look at our dishwasher and he told us that; the dishwasher cleans with enzymes in the dishwasher not water pressure, and we need to make sure the water in the kitchen faucet need to be hot before starting the dishwasher, we also need detergent, rinse aid, and citric acid added to each load. Adding all these products to the dishwasher does not fix a poorly designed product. This product does not clean the dishes, even with rinse aid the glasses come out cloudy. The dishwasher has a power blast button, it does not clean the dishes any better than the regular setting and it runs for four hours. We will never buy another Maytag product.

Model mdb7749sbm. Unit is just over 1 year old and fails in the same way everybody else in complaining about. Here is my question, this failure mode is obviously a designed in feature providing planned obsolescence to the device. Why is this company not being held to account for the damages in this case? Are all the judges that bought that no suit can be brought?Have all of you contacted your state consumer protection organizations regarding this issue? I would also recommend that you write both your state senator, the state consumer protection organization and any media outlets you can think of. High rate of control panel failure, devices activating by themselves when people are potentially away from the house, risk of fire or flooding... these are serious things and I would think a story that some news organization would surely be interested in digging into. Now that would serve to light a little fire under the Maytag organization if something like that was to occur.This sure seems to me to be a defrauding of the consumer - selling them a product at the top end of the price range that has such a significant design flaw that in the end can only be considered not fit for purpose. I havent yet contacted Maytag and Home Depot (who I believe are fully complicit in this as well), but I will be doing so to give them a chance to make this right, which I fully expect them to decline to do. Then I will begin writing letters. Am also considering small claims court. But above all, do not just accept this and move on! Companies like this need to be held to account, and they need to be reported so that others purchasing new devices in the future know to stay away from them.

I purchased a Maytag dishwasher in Jan 2012 at Home Depot. It ran fine for 1 and 1/2 years and was only used 2-3 times per week. I returned from vacation and now needs a new control board at a cost of $300. I felt Maytag was a reputable company and am very disappointed. I am a senior and on fixed income and now sorry I chose a Maytag. I will get it fixed this time but that is the last money I will invest in Maytag appliances and repairs. I worry that the washer and dryer will go next as they are also Maytag and are just over 1 yr old.

I was sooo excited to get this very very very expensive washer and dryer only to have the worst disappointment and let down...the washer in particular is horrible!!! It doesn’t wash!!! I thought I was crazy until I started reading all of these other reviews and found that many more people have had the same experience as I have... The tub never fills with water and the clothing never gets clean. I would love to start a class action against Maytag and get my money back or get a replacement.

Purchased Maytag Dishwasher MDB8959SFH4 as part of a kitchen renovation with hardwood floors. Realized that the dishwasher was leaking intermittently. Appeared that the door wouldnt latch properly. Called Whirlpool (parent company). Technician came out to assess the situation - couldnt recreate the problem so suggested replacing door seal. I try to explain to him that in my opinion it wasnt the door seal but a failure to latch because the top rack was not retracting completely on an intermittent basis. He also suggesting replacing the latch. Repair was carried out and same issue arose three days later. I systematically removed one dish at a time and then tried closing the door - after removing about the 6th item the door closed. Called the repair company today and they told me he had just received a recall from Whirlpool - apparently an issue with the tracks not allowing the rack to retract properly - what I have been saying all along. I called Whirlpool but they insisted the notice was sent out some time ago. I called Home Depot where I bought the appliance and they confirmed that they were not aware of this issue. I suggested they should not be selling this dishwasher until Whirlpool remedy the manufacturing defect. I will follow up with Whirlpool to let him know I have spoken with Home Depot and they were not aware of the issue.

This is a Maytag Neptune MAH8700AWW. This machine has been repaired a couple of times already and it has a will of its own. When it goes into that fast spin cycle that will kicks in and it starts moving. I wonder if someday its going to attack me. So, last Friday night we put a load in and it went into that fast spin cycle. It was making a noise like an elephant in labor so I looked in the laundry room.... Clouds of smoke were billowing out of the top of the machine. Our house will filling up with washing machine smoke! My husband stopped it, but I think it was a gnats hair close to bursting into flames. He looked into the front of the machine when the smoke dissipated and the entire gasket was in shreds. No more Maytag. Never. Im done.

I have never owned a Maytag in my life but was told it was the best on the market. That is so wrong. I purchased my Maytag Bravos washer and it has been a nightmare. Never again will I buy a Maytag. I have replaced two belts. It never spins the clothes out. Always have to restart it to respin. It turns off in the middle of the cycles. It will take hours and hours to do one load. At this time it just puts up the minutes and counts them down...does nothing. I am just fed up with this washer. I also bought a Maytag Centennial Commercial dryer. I have replaced a belt once. I would highly recommend not buying the Maytag Bravos washer. Save yourself the headache.

Purchased washer last Nov. It broke over month ago, tub cracked and would no longer spin. The part took month to get. Same day was repaired. It broke again after 2nd load of wash with the same issue. I want a buy out or a different washer. It also tangled the clothes. Model no WET4027HW0 Purchased from Lowes which had good service.

After replacing plastic parts that spin tub twice, now the computer is wasted. Purchased not even 3 yrs ago, now I have to buy a new washer because the computer system is not covered under warranty. REALLY!! The most expensive part. Not worth fixing. Never washed really dirty clothes when it wasnt broke down. Agree with the class action I would be in. Dont buy people and now I am off to pay to wash my clothes.

Consumers be aware! Anyone who’s considering purchasing a Maytag Appliance I would highly suggest reconsidering! I bought a $2000+ Maytag fridge Model # MFT2776FEZ00 in March of 2017 and have had numerous repair calls on it: Several for ice maker not make ice, ice freezing in the bucket into 1 big CHUNK, water running down front of door on the inside and outside, to not working at all and ice maker needing to be replaced. Several calls for fridge not properly cooling (temperature was set at 37 degrees F but the temperature in the fridge is 55 degrees F - per 2 thermometers), food is spoiling. The back inside of “Temp Controlled Pantry” is freezing everything and whole back wall behind the drawer is frozen with 1-2” of frost and ice. Defroster is not working and again parts being ordered to repair an obvious issue with this model.I contacted Maytag and their response was “sorry, we can document the problem.” They will do nothing more! These Appliance companies are ripping off the consumers! Everyone passes the buck! Repairman says, contact the Appliance store you purchased it from, Appliance store says, contact Maytag, Maytag says it’s the repair companys issue.

I am not dissatisfied with hhgregg, but with Maytag products. I purchased the Maytag Centennial Top Load Washer and Maytag Centennial Dryer to match. I was a bit leery of the new energy star models that use he only type detergent, but decided that was the newest and greatest thing out, so how could it be wrong? For the past two months, I have been sooooo very disappointed in Maytag. Neither of these brand new machines are worthy of being considered brand new. The washer takes extremely too long to wash a normal load, too noisy, and has ruined several items of clothing, due to malfunctioning distribution of bleach, fabric softener released after clothes are through washing. There has also been several times that the load wash is complete and the clothes are not even wet (like they were never involved in a wash cycle). As for the dryer, you have to run it through two 40 minutes cycles to get the load of clothes completely dry, so much for energy-saving. This is my first complaint to anyone, but after reading several reviews on Maytags website, I am reassured I am not alone. There are hundreds of other dissatisfied consumers of this Maytag product. I will be writing a letter to Maytag, requesting a refund.

The washer does not wash the clothes, period. It leaves dirt and soap in the machine along with the unwashed clothes.

I purchased a bottom freezer Maytag refrigerator two years ago. It recently began leaking water onto the floor from the freezer compartment. I just had it serviced and the serviceman told me that it was a common problem. The duck-billed check valve gets plugged. This is a problem with Maytag, Jenn-Air, Whirlpool, Amana, and KitchenAid refrigerators as they all share the same manufacturer. There is a service bulletin out on this that lists hundreds of model numbers affected by the problem (Technical Service Pointer #: W10632338). I think it is criminal that consumers are expected to pay hundreds of dollars to have this manufacturers defect repaired. I tried to find a place with the government to file a complaint, but wasnt clear who had jurisdiction. Perhaps a class action suit is in order. There have to be millions of consumers potentially facing this problem. Anyone with any knowledge of how to further pursue this defect, please comment.

We bought our Maytag Bravos in December 2010. Four months out of warranty, like many other complaints Ive read, we started getting the loud jet taking off noise from the laundry room. Now we are having issues with the lid lock not allowing you to get to the clothes. This machine tries to spin three times and then locks up. It literally locks the lid and will not allow you to get to your clothes! For a machine to fail just four months out of warranty is a joke! After investigating the problems with the machine, it will cost us more to repair than what we originally paid for the washer in the first place. Give me a break! There should be a recall and Maytag should have their feet held to the fire to replace these less than adequate high-dollar machines!

I purchased two high end Maytag machines, one washer and one dryer, approximately 36 months ago. I did not buy the extended warranty because I was foolishly convinced Maytag sold reliable products. The dryer required service twice within the first 18 months. The washer, which is computerized, is almost unusable. The sensors dont work properly. It does not spin without continual restarting the machine. It takes me hours to wash one load of laundry, and even then it is not spun properly. I wrote Maytag headquarters twice via e-mail, with no response. Even though their website says someone will get back to you within three business days. I called Maytag on August 12th and was told there is nothing they can do because I didnt purchase the extended warranty. So the bottom line is you can spend thousands of dollars on their machines but dont expect them to last, or work. And Maytag will not stand behind their products.

Bought Maytag dryer in December 2016. Worked fine for first 3 months. Then blue coloring showed up on back of drum and came off on white clothing. Had tech come out. He took pics and send to Maytag. They said it was normal. Further talks with customer service brought statements that we caused problem by drying blue jeans. Funny we never had. They just continued to say this discoloration was normal and we did something to cause problem and nothing they could do. But at least they were sorry for our problem. Whirlpool does not stand behind products. Dont buy.

My Maytag dishwasher control panel stopped working. The control panel failed, it was replaced. The replaced control panel failed. The control panel failed again and needs a fourth (4th) control panel. I have had to pay for service calls and control panels. I only use it 1 to 2 times per week. This is obviouly a lemon. I would like it fixed and to be reimbursed for the lemon part and service calls.

Bought mdb7609aww2 dishwasher in 2010. Now I cant use it as it will not start even though the panel lights of my selected wash cycle work. I looked up on internet how to reset it, but I only get a half cycle. Called customer service and for $269, I can get it fixed and get a one-year warranty. Wow, what a deal. Might as well get a new dishwasher. Joining the lawsuit. It is about time corporations take responsibility for defective merchandise, not make money to correct their mistakes by charging customers for overpriced parts and stupid worthless warranties. A pox on them.

Model MDB7749AWB2 Dishwasher - we purchased this dishwasher 3 years ago on 12/23/2011 and it appears to be falling apart. We have replaced two thermo fuses, one door latch/switch and now need the front control panel and handle because two mounting locations for the six screws have broken off. I truly expected a much longer product life than three years when I purchased a Maytag. So much plastic in crucial high stress areas must have slipped by the engineering folks. Or was it just cost cuts. I believe it will be a long time before I consider a Maytag product again based on this one. Thank you.

Please save your money and do not purchase a the Bravos XL MCT Washer and Dryer! I am sickened by the fact that I spent $1,800 on the biggest pieces of junk there ever was. Youd think a company like Maytag would be able to build a product that worked properly. We are getting ready for our FIFTH visit by a service repair company that will only plug in their computers and say nothing is wrong. Well here is what is wrong: Washer does not rinse all of the soap and I have many, MANY, pieces of dark clothing that are ruined because of the white streaks all over. I have done EVERYTHING the service guys have said to do; use less soap; use the deep water wash cycle, etc. etc. There are only two of us in the household so my average load size fills the EXTRA LARGE drum maybe half full so all their advice hasnt worked. It does not rinse the water out of a load of towels (remember there are only two us so not that many towels) and I have to run it through a rinse and spin cycle. Waste of time, energy, AND money. I washed a single coverlet and had to run it through a rinse and spin cycle twice to get the water out! If you use the bedding cycle, it runs for 90 minutes and still doesnt spin all the water out! The dryer is not better either. On average, it takes one hour and ten minutes to dry 3 bath towels, a couple of hand towels and a wash cloth. One of the service people that came out, checked our dryer vent and said everything was hooked up correctly. Talk about a waste of energy!! I would do anything to get rid of these pieces of junk but we spent so much money on them Im stuck until I win the lotto or something! I cannot stress enough that you will be wasting your money if you buy any washer and/or dryer product from Maytag! Believe me, I regret it every day!

I have had my washer and dryer for more than 5 years. As normal, over time, stuff wears out and parts need to be replaced. The manual doesnt list part numbers that are needed. The website doesnt pull up part numbers when you type in the model number. After paying for overnight shipping that isnt guaranteed (and was more than the part itself), it didnt show up until a couple of days later and it was the wrong part. I would have to pay for shipping costs of the return, now tripling the cost of the actual part. Calls to customer service were not at all helpful as all they could say was that I would have to pay for the return shipping and they were sorry there was nothing they could do. I wont be purchasing anything from Maytag ever again.

The Maytag Maxima XL front load steam washer is awesome. Its reliable and does an amazing job. There are so many features and settings and it makes my life easier when it comes to doing laundry. My favorite feature is the allergen setting which gets rid of allergens in my fabrics.

I have a Maytag washing machine for close to 20 years, so when it was time to replace it, I bought another Maytag: the Bravos. I read reviews, and most negative ones complained that it used too little water, twisted clothes, and was noisy. But I wanted an HE and can tolerate noise just fine. What I cannot tolerate is the fact that -- less than 2 years after purchase -- the control panel is malfunctioning, and it will cost $500 to repair. Id rather buy a new washing machine than throw good money after bad on this one. Bye-bye, Maytag.

We had a Whirlpool dishwasher for 24 years, and when it was time to purchase a new one, I did a lot of research before choosing our Maytag. Reviews by other consumers who had purchased dishwashers was very helpful in making our decision, and we have had no problems in the almost 18 months that we have had this dishwasher. It is very quiet. It washes and dries the dishes with no streaks, although I wash off the dishes before loading them. It provides 5 cycles and 4 options and lights blink, when the washing and drying cycles are complete. I would recommend the Maytag, Model #MDB4949SHBO wholeheartedly.

I bought this washer from Lowes in 2013. It worked okay for a little while but lately it stops mid-cycle. Clothes are soaked and all of the soap hasnt been rinsed out. Poor excuse for a washing machine! Will never buy a Maytag again!

On May 11, 2010, I purchased a Maytag washing machine from Lowes. On June 22, 2011, the machine wouldnt empty out on the rinse cycle. Lowes was called as the machine was only one month out of warranty. They dispatched Appliance Plus for a service call which would be $80.00 just to diagnose the problem. It turns out the machine needs three parts - a timer, an ATC switch, and a rinse switch. All totaled, this will add up to over $300.00, plus the $80.00 for the service call.Appliance Plus tried to contact Whirlpool to see if Whirlpool would at least pay for parts, being it was only one month out of warranty. The answer took 5 days and the request was denied. I was told I should contact Lowes Service Advantage and maybe they could contact Whirlpool for a special consideration, again, being it was only one month out of warranty. I made the call and they said to give them two business days turn-around for an answer. On June 30th, Lowes said Whirlpool was looking for the serial number and I provided it. They told me to give them another 2 business days turn-around. On July 3rd, I again called Lowes and they informed me that they still hadnt heard from Whirlpool. Finally, on July 7th, I received a call from Lowes saying Whirlpool denied the request.

I purchased this high-end dishwasher 7 years ago and 3 years of fairly light use, the control panel on the top would operate sporadically or not at all. Called the dealer who sent out the repairman that installed it and had to replace the control panel to the tune of $300 once the labor was included (took 2 visits as he had to order the part, so 2 trip charges). Now 3 & 1/2 years later, it is doing it again!! A call to Maytag and then a transfer to Whirlpool customer service got me nowhere. They said there were no recalls or documentation for problems with the dishwasher. Really??? I see lots of complaints on this problem with very similar Maytag dishwasher models. They would not send me a new part at no charge as a result but offered to set up a service appointment for me so I can spend another $300 (probably higher now after 3 years) and would register my complaint. Thanks for nothing!Doing that would turn my originally $900 dishwasher into a $1500 one with the result that it will probably fail again in 3 years. Absolutely ridiculous customer service. I saw a YouTube video on taking it apart and applying silicone around the ribbon connections as others have done in the hopes I can get it working again for a while as I dont have the $$$ needed to replace it again on a retired fixed income. :(

We bought a new Maytag fridge in 2013, french doors, ice maker on the bottom. In 2 years we have replaced the control panel on the front door 3 times. Each time the plastic panel cracks and breaks free. The last time they replaced the entire door, all on warranty. Well 3 months later it does the exact same thing. I call Maytag and they say, fridge is past its warranty period so no coverage. It will cost me about $600 to replace this control panel.

My 16-month old dishwasher, which is not being used everyday, broke its control panel. Maytag will not fix it for free because they only back it for one year. This is a major appliance, shouldnt it last more than 16 months? The cost to repair is almost as much as a new dishwasher.

Well I like all the other people have the very same problem. Ruined floor from sheet of ice that forms on the bottom tray daily. I was told I need a new main board which I understand is about $500.00. I am 55 years old and this was my first brand new fridge. I am so so upset. I grew up with the whole Maytag repairman commercials where he was so lonely cause he never had any repairs to do. All my life I grew up with these commercials. I thought I was buying the best. What a disappointment. It has been in my living room for 2 years. I keep thinking something wonderful is going to happen. Now I have to pay someone to haul it off. Great.

This oven has been used so very seldom that I didnt feel I could rate it until now. We use the oven 1-2 times a week since purchasing it in March of 2018. There hadnt been any reason to use the Self Cleaning part of the oven until last week. I have had a oven with self-cleaning for 20 years and the oven went out so we purchased this one because of its sleek look and features. However last week I decided to use the self-cleaning setting on it and came home after being gone all day to find that the house smelled like it had a fire burning in it. I ran to the oven to find the whole inside cover in a white powdery substance. It looked like a snow blizzard had gone on inside of it. I was use to a small amount of white residue being inside the oven after it finished and it just wiped right up. We spent hours vacuuming it out then scrubbing it down with vinegar water and a sponge with a scouring pad on it. The casserole spill was still on the bottom, most of the enamel is gone and the glass will not clean off. I did not use any chemicals in the oven prior to turning it to the self-clean mode, I believe that it overheated and burnt the enamel off and distorted the glass. Whirlpool offered to send me a cleaning kit. I told them that would do no good. I had already scrubbed and used a razor blade to try and clean the bottom and the glass and them sending me different cleaning supplies would not fix the fact that 80% of the inside protective coating on the oven is gone. Now it is a porous surface. A Serviceman was scheduled and he called prior to arrival today and asked me to explain what was going on with my oven. I explained and he said I can almost guarantee that Whirlpool will say that it is cosmetic and they only cover cosmetic for 3 months and that I will have to pay for a $100.00 service call. This is a load of crap. This coating is part of the oven to keep it clean and protect the metal from the high heat of baking in it. This is not cosmetic feature like the outside stainless steel finish or the black trim decor. The inside doesnt look pretty. It is a function. See the photos below. Whirlpool Range Item # 805150. Model # WEE510S0FS.

Topload Maytag Bravos washer sounds like a jet on spin cycle. Called Maytag, no recalls or service issues. Just wanted to sell me a service contract for over 300.00 dollars that would fix it and be covered under warranty for a year on anything that went wrong. Could set me up with a service call, but it was six days from now - no thanks. The washer this replaced was a Sears which was 26 years old. It still worked and I sold it for 75.00 dollars. Guess I will stick with Sears!

Here recently I got a bravos washer x series because it suppose to cut down water usage. Well that it did. Now going on 7 months of having it now its starting to act up like when the cycle is done it will lock again and repeat the cycle all over. I use the normal or powerwash cycle and here recently how its suppose to sense the load and then start spraying the clothes with water and detergent. Well not here. Lately it still senses and spins and then starts filling up like its on the bulky/sheet cycle but its on normal cycle and it doesnt fill all the way up - just 4 or 5 inches of water. So I dont know what is up with this piece of crap and why its acting this way. Other times it will work fine on the normal and the other cycles but now its just acting all crazy.

Bought this Maytag Bravo washer in 2013 expecting long service life like I had with my previous machine. After 2 years spin cycle noise got progressively worse. Until now it roars loudly and keeps stopping in the spin cycle for rebalancing. Called Maytag. Experience was as described as others have reported with them and their repair service. Absolutely no help unless I spend another $310 for extended warranty to cover the $380 part (tub and bearing - 1 unit - cant get only the bearing). Paid $800 for the washer now more for the repair wanted. $1100-$1200 for a machine that will need repair again in a couple of years? Dont think so. This machine is only good for a boat anchor. Going out today to buy a replacement for $400 and it wont be a Maytag or its affiliates brand. Feel like a class action suit would be good for Maytag to wake up to.

Purchased a Maytag Dishwasher (Serial # P33706417) in Sep. 2013. In the beginning was working fine. After a year and a half started having problems pushing the button to start, not starting. Had to wait a few hours then hit it again and all the lights would light up and then it would start washing. Then when done, some lights stayed on and never went off. Then a month or 2 later, same problem but only a couple of lights would go on and when done 2 lights would blink continuously. After several months now, none of the lights are working and cant get dishwasher to start. Called a tech and he said the control board and the touchpad were not working. Would cost me over $400 plus shipping, etc. to for new. Very frustrated with Maytag, as we havent even gotten 2 years out of this dishwasher and the 1 year warranty has expired. DONT BUY A MAYTAG!!!

Our home has seven Maytag appliances: an upstairs kitchen, downstairs suite and laundry room. All were brand new six years ago and what we thought to be good quality by the price we paid for them. We have lived to regret ever dropping a cent into Maytags business account, as we have had nothing but trouble with them. We dont have small kids or teenagers abusing them. Its just us and a very responsible single adult downstairs. And every time we turn around, one of them is costing us nothing but money and grief. Our first problems began with our upstairs fridge when it was only two years old. At that time, it cost us $400 and since then, it just goes on and on. Last week, our downstairs fridge quit, and today, our upstairs one quit. We have had work done on our range, as well as our washing machine and dishwasher. If you are thinking of buying a Maytag appliance, dont, unless you like to throw away your money. I couldnt believe when I looked up Consumer Reviews on Maytag appliances tonight that I would find only 1 out of 5 stars, and read all the terrible reviews written by angry consumers. Well, add me to the list because I will never buy another appliance from Maytag again, and am beginning to think its time to sell this house to get rid of these stupid, useless, pieces of ** Maytag appliances! Sorry, people, but I cant afford to keep replacing them!

We purchased the washer and dryer in June 2009. This past weekend, I noticed that the washer was leaking. The price to fix it is half of what a new machine will cost. I am very disappointed in Maytag. When I purchased the machines, I thought I was purchasing a quality product. Ive had paid much less for washers that last longer. Needless to say, I am shopping for another washer this week and it will not be a Maytag or Whirlpool. They are pieces of junk!

I bought this new washer and dryer pair at Lowes August 2018. I chose this brand because of the very large wash tub (5.3 cu ft) since I have king size bedding. My previous washer was a front loader, and there were problems with the door seal molding and stinking, and loads had dry spots on them after washing. So within a very short time, I realized I hated this new washer. Very noisy, no agitator, very long cycles. You cannot adjust the time or water levels, and the biggest problem... I CANNOT REACH THE BOTTOM OF THE TUB! I had to steal the grabby toy out of our toy box to pull the wet load out! The laundry comes out all tangled up and horribly wrinkled, even when using the wrinkle-free setting. I line dry a lot of my clothes and now have to iron everything. Never had to do that before. I know Im stuck with this set, but will look forward to the day when it dies and I can buy new ones again.

Front load washer is four years old. Approximately two years after owning the washing machine it started burning and ripping our clothes. Maytag sent someone out to repair at no cost. The problem stopped. However, approximately two years later it is happening all over again. Thus, there is either a deficiency in the Maytag product or the repair has failed. Maytag will only repair at our cost. True, the washer is four years old but the same problem keeps happening. Plus, that is not a long time in the life of a washing machine. The customer should not be held responsible for a recurring problem with their product. The front load washer and dryer were very expensive. We will NEVER buy Maytag and we will continue to share our disappointment to whoever will listen. It is shameful that Maytag says they stand by their product but when its put to the test Maytag completely fail. Double thumbs down for Maytag and customer service!!!

According to Maytags manual Odors and smoke are normal when the oven is used the first few times... Exposure to the fumes may result in death of certain birds. What about humans? I had serious respiratory problems and the industrial-level fumes lingered after dozens of uses. Neither the upper nor the lower ovens are calibrated. Upper oven baked at 325 when digital readout said 350. Lower oven had to be set to 365 to cook at 350. (After several puzzling baking disasters I bought an oven thermometer.) YOU are supposed to calibrate it yourself with cryptic instructions and a lot of trial and error.

We bought a Maytag refrigerator (single-door) with a top-loading freezer that failed after four years. The freezer began to ice up and two repairmen from the company that does the extended warranty repairs in the Ottawa area were unable to figure out the problem. After the second visit, the freezer iced up again and the thermostat appeared to be failing. Even though we had an extended warranty, we just gave up and went to a different dealer to buy a new refrigerator that could be delivered within three days - and it wasnt a Maytag or any other of Whirlpools brands. If youre thinking of buying a Maytag refrigerator, you should reconsider. In fact, you should twice before buying anything made by Whirlpool.

My new dishwasher had a defective board and worked erratically. Shortly after the warranty was up it stopped working completely. I contact both Maytag service and Home Depot on several occasions with no satisfaction. This a well known defect. Apparently the board replacement and service would cost in the range of $250-300. Too much for me as a senior on fixed income to justify. No dishwasher for almost a year. I then read an article indicating there was a class action settlement in California on the same make and model. I called Maytag again and after spending 2.5 hours on the phone I finally reach a person who sent out a service repair person. This person showed me a memo confirming the problem with the board. No recall but... if a customer is persistent they will give you the board. Finally new board installed at no charge.

I want to document my experience with Maytag refrigerator model # 1958XEW1 and serial # K12947360. I purchase this refrigerator several years ago as a result of a recommendation of a general contractor who was doing kitchen remodeling work for me. After doing a brief online research on Maytag I went to Yale Electric a store in Boston to purchase a Maytag refrigerator. Worst mistake I ever made and I will never buy a Maytag product again (sad to say). This refrigerator has been leaking since the day it arrived from the store. Unfortunately for me I didnt notice the fridge leaking until after the warranty had expired (my bad). The leak was such as I could not isolate or say it was the fridge because the water would pool in an area that was away from the frig on my kitchen floor. One day by coincidence I actually saw the fridge leak so then I knew the water on my floor was coming from the fridge. I contacted Maytag who mentioned by that time my warranty had expired, however other people who had purchase this fridge model were experiencing the same problem. Maytag said that this leak problem could be fixed by changing the tubing located in the freezer section of the refrigerator to what they called a duckbill type of tubing. So I had that part sent to me and it was installed in the refrigerator freezer area. As you can imagine because I am writing this negative review that the water leak problem was not corrected and there is still water pooling on my floor from this refrigerator. I will never buy a Maytag product again and I wanted to share this experience with other potential buyers of Maytag products.

I purchased a Maytag (as Maytag was always rated the Best) and from the start was not happy with the product. I contacted Maytag (Whirlpool, the makers of Maytag) and was told to get stains out, you had to pre-soak and scrub the area... really? Then I might as well just hand wash all of my clothes and hang to dry. I would not need a washer. My clothes do not come clean at all. DO NOT PURCHASE A MAYTAG (or I think any washer Whirlpool makes as they do not back their products).Prior to this, I had a Whirlpool washer with agitator and loved the washer. Clothes were always clean, and I did not have to pre-soak stains for them to come clean. Go Figure! I have never been so disappointed in a washer or company. I am now looking to purchase a new washer as I have had it with this one... and it wont be a product made by Whirlpool.

I purchased this oven in April 2015. I have had nothing but problems with the unit. The temperature is off. I have had the probe replaced in July and will be done again next week (January 26, 2016). The AquaLift self-cleaning feature does not work. I ran the self-cleaning feature about 8 times and back to back on several occasions. The service providers stated that it really doesnt work and there is nothing they can do about it. The front of my oven, above the vent, is stained from the oven exhaust. They said there is nothing they can do about that either. The last service company that came out for a service call to check the oven temperature came without the proper tool to check the temperature and ended up snapping the propane line. I was given 6 month of a free extended warranty for my inconvenience and told that the company does not replace models. They will continue to come out and repair them. I will never buy another Maytag appliance again.

I purchased this refrigerator 1 1/2 yrs. ago. The refrigerator stopped getting cold about 3 months after warranty expired. I called Maytag company and told them how disappointed with their product and also how angry I was after spending $1500 only 18 months ago and now it is useless! They kept asking me if I bought the extended warranty and I said I didnt think I would have to after buying a brand new product. And then it breaks so soon!! And now they want me to spend an additional $359 to get the warranty... what a racket! She told me to look under the fridge for leaks. Sorry I cant, Im disabled. She said too bad and would have service man call me but that would be even more expensive. Woops, disconnected.

Maytag is a reputable brand name for a washer & dryer. However, they have done very well in the oven/range industry as well! I own a oven/range for over 4 years now and it works great???! Food is cooked to perfection and cleaning???? And self-cleaning is a snap!

Holds a lot of laundry. Spins laundry almost dry so its quicker in the dryer. Easy to load. Easy to add wash soap and fabric softener. Only problem is its very deep to reach the laundry at once its done if youre not real tall.

We love our Maytag Dishwasher! It's very durable, doesn't use a lot of water and really gets our dishes exceptionally clean. The best part is that it sterilizes on the final cycle! We've long trusted any Maytag appliance in our families for generations.

I would not purchase a Maytag in the future. The top oven does not work, and one of the burners is semi functional. Considering I have only have the oven about 5 years. I am not happy with the the product. In the future I would seek other options, Maytag is not on the list of products for consideration.