Purchased new Maytag washing machine July 17, 2011. Have had several problems with it over the past three years. Most of the time it would not complete a load of laundry and would get stuck before the drain and spin cycle. Last week, the spin cycle became extremely loud. Had a repair person come out and was told the motor bearings were bad. Estimated repair cost $700. Purchased this unit new for $569.00. Called Maytag, was told that 10-year warranty on drive motor and wash basket did NOT include the bearings. Asked if they could help out with repair cost, was told no. Will never purchase another Maytag product again as they do not stand behind their products. Household has 4 people in it so use of this machine was light to medium.

We are a family of nine so I wash a lot of laundry. We bought this washing machine a month ago and hoped it would perform like our prior one. The problems are many. It is too smart for its own good- it requires a cleaning after every 30 washes but gives you zero warning beforehand so you will already have the clothes in and started the cycle when it will stop the cycle saying it needs cleaned. There is nothing you can do to override the cleaning cycle, so you are forced to remove your sopping wet clothes and run the cleaning cycle- wasting time and money on precious water! It also wants you to use its specialty affresh to clean it with, adding cost we hadnt planned on. Then you cant tell when to put the clothes in as it tells you to start the washer and then add the clothes, but if you put the clothes in first sometimes it wont start because it wont sense properly, and if you start it without the clothes. Then when you stop to add the clothes it wont start it with the clothes in it- which way does the machine want it?! So it is a guessing game as if the washing cycle will even start. And the washer wont hold as many clothes as our last one did. If there are too many clothes, the cycle will stop and it will refuse to wash until some are removed. Whenever there is a problem starting, which in one month has been four times now for us, it is a huge guessing game as to what is wrong for why it wont start. I dont need this kind of frustration! Further, the locking mechanism in the washer is plastic, and I know from experience that plastic parts will be the first to break. Had I realized this before purchasing, I would have looked for a metal locking device. My guess is when it does break, the whole washer will break. Also, from day one, it has made a sound that Im not sure is normal. It sounds almost like grinding gears every time each various phase starts or stops (washing, rinsing, draining, etc.). I sincerely hope this isnt a manufacturer defect as we didnt buy the extended warranty. We researched this model before buying and many were happy with it but I hate this washer! I loved my last Samsung washer but it rusted all over after just five and a half years even though it still worked great, so I didnt want to buy Samsung again so we took a chance with this Maytag. I am regretting this purchase. I consider myself to be a person easy to please. I want a washer that works that wont rust that you can put a ton of clothes in and throw it in the wash and forget about it. I dont want all this high-tech sensing stuff that just messes up and is highly inaccurate in what it senses! Why cant companies offer a simple, high quality product anymore that works, without the added costly features?! The model number is: MVW6230HW0. Avoid this model number.

Purchased the Neptune washer & dryer in 2002. Did not purchase any additional warranty. I have had Frigidaire, Kenmore and Speed Queen washers previously and used them until they quit. I have not had any problems with either the washer or dryer. No mold, no smell, nothing. I did laundry for 2 children and 2 adults, 6 to 8 loads per week with half being heavily soiled work clothes. I still wash 3-4 times a week. I was able to wash & dry king size blankets and comforters for the first time with this set. Washer and dryer are located on the main floor of house and are the quietest units I have ever owned. They may quit tomorrow, but they have done the job that they were designed to do. I am well satisfied with the quality and performance of both units and would not hesitate to purchase Maytag appliances again.

Please Do NOT purchase the Maytag Aqua Lift Gas Range. It does not clean anything, you will pay more money for a cleaning oven that does not clean any grease or droppings if you cook. This is not an Oven for any one, or family that cooks large meals or has gatherings. I had the technicians at my house over 4 times and they confirmed that this oven is not a self cleaning oven. It doesnt get hot enough as your self cleaning ovens. And MAYTAG did not want to hear anything, basically not clean much, but advertised as a self cleaning oven. Having been a Maytag customer for years I will never buy a Maytag product again. And we need to support American made, but not when the consumer is misled.

We purchased a refrigerator in December 2010 with a 12-month warranty. Since the refrigerator was delivered, we have experienced nothing but problems. Most recently, there was a problem with the auto defrost causing us to lose all our food stored. It also caused water damage to our floor. We scheduled maintenance with a contracted company through MayTag. After three scheduled visits, which made me miss 3 and a half days of work resulting in an additional loss of over $300, our refrigerator is still broken and they just want us to schedule another maintenance visit. When calling Maytag customer service we are literally told, “your loss, there is nothing we can do to resolve your issue, we can only continue to send out maintenance.” I am so disappointed in this company, the product, the customer service, maintenance service etc.

I have had my stove since 2004. A problem I have had was when I asked it to clean the ovens, it quit working all together. A service person was called. Also sometimes when I turn on one burner, another one will turn on instead. Yesterday I turned on a burner to low, and it did not turn on at all.

I have had this washer (top loading washer model MVWX550XW0) almost 2 years. It has ruined some of my clothes. It does not properly wash anything. I have tried every possible solution. I cannot use the HE powder detergent - it will not rinse out. I tried using less than required and double rinse, absolutely did not overload. Even using the HE liquid still did not get clothes clean. I used the number one detergent to the cheaper brand - it makes no difference. I still have to double rinse everything. Small throw rugs will not even get totally wet or clean. I took clothes to the laundromat just to make sure it was the washer. It is this washer. I know I have waited too long to register my complaint, but I have basically thrown away $1200. Also, loads of clothes would take up to 1 & 1/2 to 2 hours to wash. Now that is definitely not energy efficient. I would love for you to pick it up and bring me a standard washer and dryer. I work for a research firm and know when companies really care about their customers. I will be interested to see if the Maytag Man really cares. The only reason I did not check angry is because of my delayed response.

Washer is Broken After 1-1/2 Years: Yes, the code F51 has come on quite often. Now, my washer does not work at all! Does not spin out, makes thumping noises even though I have taken good care of this machine. It cost me quite a lot of money and thought that this was a wise decision. It’s broken after a year, unbelievable! Also, clothes don’t get clean. I had to wash 2 - 3 times. The clothes wrap around each other and the machine does not clean them well. It’s a horrible machine. I have not called Maytag (Whirlpool) yet as I see from the comments that they will not stand behind their machine. I dont know what to do!

I purchased our washer and dryer together in 2012. Now my washer is making a really bad sound on the spin cycle. I talked to Maytag in Tenn. and they wanted 130.00 just to show up. Plus 300 to 500 for the parts that was needed. Wow. I am retired and on a fix income. I called a local repairman in OkC. After telling him the brand of washer I had, he said he would not come out to fix it because of the money would be expensive. 300 to 500 dollars for parts. He said it would be cheaper for me to purchase a new one. This seems to be a real problem. I talked to Maytag supervisor and she could not wait for me to get off the phone. Nor would she give me her name. Buy Whirlpool!!!!!!!!

I would say you have plenty of options when choosing a color for your dishwasher. You can choose black or stainless. Try one today you wont be disappointed. I load plenty of dishes into the space. It has extra pockets for little things and it has plenty of hooks and hangers to use for bigger cycles. Kenmore Dishwasher runs great. Very efficient and cleans the tough stains better than any dishwasher Ive ever used. I would recommend this to anyone looking to buy a dishwasher. Of all the dishwashers I researched at Lowes and Home Depot and Sears and Ace and other local stores, the Maytag was the lowest price with all the features I wanted.

I tried emailing Maytag but from what I read on consumer reports I doubt Ill get an email back. After our 20 plus year old Kenmore fridge was taken by hurricane Sandy I decided to try Maytag. What junk! We have a bottom freezer and were getting water build up on the bottom under the basket. In order to keep the water from leaking on floor I had to chop the ice out of the bottom every 2 days. My husband got frustrated and took the whole freezer apart only to find all the coils were covered in ice. Soon after that the ice maker stopped working. Tried different things to get it working. We finally took it apart and found the factory did not screw in all the screws on the inside so they fell out on the circuit board and shorted the thing out. Lucky it didnt burn the house down. All I can say is junk! Do not buy!

I purchased a Maytag Centennial Washer at the end of last year. Within 2 weeks, I knew it wasnt a good washer and asked my husband if we could return it. He said, No. I dont like using the fabric softener dispenser, so I used to use a Downy ball. This washer doesnt spin hard enough to open the ball. I tried 3 separate times. Each time, the ball came out with the fabric softener in it at the end of the cycle just like it was when I put it in. It also doesnt get the clothes clean. Im using chlorine bleach, detergent and OxiClean and our whites are gray. It doesnt get the simplest stain out and the soak feature is a joke. If you use the soak feature, the washer fills up, the lid locks, it soaks and then the water drains out. No spin or anything.Normally, on the old washers, you could just push the knob in to stop the agitation to soak something, but not now. The lid locks, which I cant stand, when the washer is working. I would like to see if it is agitating or to add more clothes if I want. Im not sure who designed this washer, but they should go back to the drawing board. Ive tried every cycle and none of them work well. It also takes an hour to wash a load of clothes. Im just so disappointed with Maytag on every level. This was my first Maytag purchase and it will be my last.

I purchased a dishwasher model #MDB4709PAM from home Depot in March 2014. There is something wrong with the electrical and it is shocking people if you touch it. Just so were clear.. MY DISHWASHER IS ELECTROCUTING PEOPLE... Called Maytag repair because hey its only five months old. Cant send anyone out for three weeks.... three. Took an hour on the phone because I had to talk to four departments. Kept asking if anyone had been hurt seriously or property damage, so they made sure their butts were covered, sigh..... Should have bought the LG.

I have been a Maytag customer for many, many years. In November, 2014 we decided to buy a new matching pair. No problems with dryer but the washer has been a nightmare from day one. Have had at least 5 service calls (lost count). The washer constantly smells. Clothes are not clean. Have to buy and run Affresh tablets weekly. Spend more on wash machine cleaner than laundry detergent. Funny thing is Maytag/Whirlpool makes the expensive cleaning tablets. The customer service at Maytag has not been helpful from day one. They recommended I buy an $150.00 extended warranty. Stupidly I agreed and regret doing it. They still have not fix the machine under the one year original warranty. NEVER BUY A MAYTAG BRAVOS WASHER.

I purchased Maytag microwave model MMV4205AAQ in 2005. I use it infrequently. It stopped heating in Nov. 2011. It must be replaced. But after this experience and reading other comments, I will not purchase any Maytag appliances in the future.

We bought a Maytag Bravos XL assuming that because of the brand name it would be a great machine. WRONG. This washer is truly awful. Every single load of darks comes out covered in soap scum. I always have to rewash every dark load with no soap for a full normal cycle in order to get the scum off. My whites are probably also scummy but often I just throw them in the dryer as I cant see the scum. Its just a very, very poorly designed machine that obviously wasnt tested before they started manufacturing and selling it. Its criminal how Maytag continued to sell this piece of junk, and Ill never trust their brand again.

We have had our washer and dryer almost 18 years and just recently spent less than $280 to get the washer going again. The dryer we haven’t had serviced yet. Great quality. So worth it. Our Maytag appliances are used frequently and keep giving out the best performance.

Model MBF 2258XEW3. I am very annoyed with this fridge. Never will buy a Maytag again. I went to this site to see what the problem with my fridge was and read that I am not the only one with this problem. From the beginning it never worked right. Often the food in the fridge got ice crystals in them so I had to up the temp. This made the freezer not cold enough so I had to lower the temp again. This is a constant affair. Now the bottom of the freezer is collecting an ice sheet or a water bath that has to be removed every other day so that it doesnt built up or leak out. Will have to buy a new fridge. But now I am worried that I might buy another lemon.

Actually, I have had my Maytag washer and dryer for 20 years so they are not new but I am thankful for this set because of the workload it does for me. I sometimes wash heavy loads (blankets, bedspreads, small area rugs), and this pair performs superbly. My son wanted to buy me a new set for Christmas last year but I definitely said no. I truly am happy that I bought Maytag and I truly believe that the Maytag repairman is a bit lonely.

Purchased a Maytag Bravos 300 quiet series and am totally dissatisfied. I have a bandsaw, router and several saws in my workshop and by far my Maytag washer can drown them all out with the noise it makes. On top of all this it does not complete its cycles before it shuts off and if you try to restart it you never know where in the cycle it is going to start at. This may occur six or seven times before you are able to complete one wash. It may take a day to wash one load of clothes. Maytag should refund the total purchase price of this piece of junk!

This is not a complaint but a love-letter. I know that todays Maytag Neptune is not the Maytag of old. But Im here to report that Im still using a Maytag washer that was built in 1982! The only thing wrong with my machine is that it occasionally goes off-balance when I wash heavy towels or blankets. Note: We inherited this machine with the purchase of a home in 1991. We were a family of 6, so this machine has done many heavy loads! Im looking forward to celebrating my Maytags 30th birthday, come Jan. 1, 2012. And I would love advice on how to replace it, eventually, with another machine that has just the basics - no bells and whistles, computerized control panels, etc.

This washer does not distribute enough water to wash clothes properly. I continually take clothes out of washer that are not completely wet. My darker clothes have white spots of detergent on them that did not get rinsed off. This product should be pulled from the stores. We have tried everything, using deep water wash, bedding wash, to get more water in the machine. Our clothes are not coming out clean. Complete waste of our money!

After having issues with bearings in a front load of another brand, we decided upon a top load Maytag. We have had it less than a year and we are not happy with the performance. We are using more detergent because the dispenser seems to be bottomless. Only the front of the little pull out drawer is visible and it never seems to reach the fill line when adding liquid detergent. There is no quick wash cycle. Not everything needs a cycle of nearly an hour or more. The spin cycle does not remove nearly as much dampness/water as our previous frontload. The drum is deep making it difficult to retrieve small items such as socks. My biggest disappointment is finding lint residue on the clothing and it remains even after an extra rinse. This is especially visible on dark clothing. Even the lint filter in our dryer fills up much more quickly than before. After researching, I found that others complained of this same problem.

Had it for over ten years, had no problems. We dont use the oven too often but it is simple to operate and has served us well. Easy to clean, stainless steel like looks on the front goes well with our other appliances. Reasonably priced too.

Had the new set for over a month now and are very impressed. If you actually know how to do laundry, and dont load it up to the top with greasy, dirt filled work clothes, etc. (like some **) you will have no problem lol. We have Absolutely nothing bad to say about Maytag products, and the new set is amazing!!!!

Bought a Maytag Bravos washer 21/2 years ago... already have to buy a new washer... not a Maytag!! It started with the ul message coming on. Never could do anything to get it to go off.... then started leaking water around the bottom... bearings went out... costs more to fix than buying a new washer which is what I DID. Not a Maytag.... thought Maytags were a great product. Believe me their repairmen are always busy, not just sitting around like in their commercial.... Never buy a Maytag appliance again.

I purchased a Maytag Centennial Top Load Washer in February 2012. I wish I had understood the workings of the washer before making the purchase. I am not at all happy that the lid locks as soon as the washer starts and unless I push a button to get the lid open. I cannot open the lid to maybe add more items or check to see if the water amount is sufficient or too much. I have no idea how much goes in for each water level. Of course, I cannot take water out but I could put more in if I see it is not enough. And after learning the water levels, I would know just how to determine the level I need. Some man must have designed the panel. Otherwise I am satisfied. I really like the large load capacity. I originally thought I wanted a front load to get a large capacity but this suits me fine.

We purchased a dishwasher (Maytag) two or three years ago. We have had nothing but trouble with it. The welds on the upper rack broke. The wheels on the low rack keep falling off. Water leak happened recently. The start button broke. My wife and I decided to just get a new one rather than keep sinking maintenance costs which are going to keep adding up.

This washer came with the home we recently purchased. I used the machine and OMG the spin cycle is NOT quiet.. I posted a video of it on FB. A friend of mine who owns and operates an appliance center watched it.. messaged me back and said Do not call repair man as it is cheaper to buy a new machine... I knew this machine sounded like a piece of **.. I know I wont replace with the same machine.

We purchased a Maytag MDB7749SBWO Maytag dishwasher. Suddenly the control panel does not work. Trying to find out why I found that there are thousands of complaints about this known defect with water and steam getting in and corroding the control panel. Shame on Maytag for continuing to sell these without fixing the problem. I expected my dishwasher to last many years based on the Maytag reputation instead I need to replace it. I am not going to spend the money on a repair with a machine that will have the same problem again according to other consumers.

I love my new fridge! It has all the bells and whistles and looks/works great! My ice maker is the bomb! Best design Ive ever seen!

Just like all the other reviews, 14 months after purchase and 2 months out of warranty the control panel on our Maytag Dishwasher stopped functioning. The “10 year warranty” is a joke a covers 3 things. We had model MDB4949SHX, $550 new.

According to Maytags manual Odors and smoke are normal when the oven is used the first few times... Exposure to the fumes may result in death of certain birds. What about humans? I had serious respiratory problems and the industrial-level fumes lingered after dozens of uses. Neither the upper nor the lower ovens are calibrated. Upper oven baked at 325 when digital readout said 350. Lower oven had to be set to 365 to cook at 350. (After several puzzling baking disasters I bought an oven thermometer.) YOU are supposed to calibrate it yourself with cryptic instructions and a lot of trial and error.

Bought a Maytag fridge model MFI2569YEM0 a few years ago. From the get-go, the ice machine would spit out ice hither and thither, mostly not into the cup or mug. Even when I held the cup up high into the dispenser orifice, I noticed it still spit out ice seconds after I released the cup, so ice cubes would spill onto the floor. Secondly, the vertical doors do not close well, and I must manually push them closed, especially the left door due to the poor design. (I noticed my neighbors more updated fridge has a better closing door. Forgot what brand, though.) Theres also rust forming on the front of the stainless steel fridge panel. It has penetrated through so I am unable to remove it.Lastly, this past week I walked into the kitchen stepping in a pool of water in front of the fridge. There was a sheet of ice accumulated on the bottom of the freezer. After some research, its likely the nipple in the back of the fridge that plugged up. I have yet to fix the problem, but so far, Maytag gets an F- in quality, and I will NEVER, EVER purchase any of their appliances again. I remember my parents washer dryer lasting 30+ years. Maytag, what happened???!!!

We loved the Maytag dishwasher when we first bought it. After about 5 years it started leaking. Had rubber gasket replace, only held up 2 years. This was the only problem.

This is a dishwasher purchased at Home Depot on March 25, 2012 for a rental unit... call from tenant said the dishwasher did not work. Repair person from Appliance Hospital went out today and said the control panel is out and the touch pad. Cost is over $500 to replace. I will have to replace this dishwasher BUT NOT WITH ANOTHER MAYTAG.

Eight years ago we bought all new top-of-the-line, stainless steel refrigerator, double oven range, dishwasher and microwave. All began malfunctioning within the first year: *The refrigerator began to make a loud rattle and the digital control pad needed to be replaced -twice within the first year. Within the next year the compressor had to be replace. *Dishwasher electronic control board was replaced twice, broke again and is still broken. *Microwave door handle broke off, and turntable motor broke.*Range burner ignition system only works on two burners and the shelf for the top oven does not fit -*Maytag refused to replace. Also, after using self-cleaning feature the lower oven still fills the room with smoke so it has been used very little. So, how much worse could it be? I had faith in Maytag-thats why we bought the brand.

I too am a victim of the faulty Control Panel that Maytag put on these dishwashers - Model # MDB7749SBM2. $149 for the part and another $149 for service call and labor - almost half the price of what I paid 2 years ago! Should have stuck with the 10 year old builder grade GE I had with the latch door and turn knob! I am in the market for a new stove and microwave - I will never buy another Maytag or Whirlpool product! When is Maytag going to make good to all the customers out there that have experienced the same issue? If yours breaks it is a very easy fix now that I know. You can order the part and it simply unplugs and plugs in the new one. All you have to do is take the door off and it is right there!

This is the most horrible washer ever. Within 3 months it would not go beyond sensing mode and never fill or wash. Tech came and fixed it... 3 times. It still happens and I have to jiggle it all around to activate it. Clothes are never clean, dog hair is never washed out... My broken old agitator machine was taken to the dump & I wish I had it back! How do the stores give this machine a good rating?? I cant do light quick washes, I have to wait forever... Our water bill is 2x higher than ever because if I dont fill the tub with deep water, the clothes dont even all get wet. Hate, hate, hate this thing.

Maytag Dishwasher MDB77495 - We bought this dishwasher September of 2013. April 2013 when you pressed the option I wanted the options auto clean, rinse only, steam sanitize and delay hours. The thing would work when pressing start but I have no idea what it is doing. The repair man replaced the board and all was good for a couple of months then it happened again. The board was replaced again and in two more months it failed again. The repair man told me that moisture was getting to the board and there was corrosion on the ribbon mentioned in another review here. He contacted Maytag both times and gave them my contact information but they never called me + they told him that they have never heard of this happening with this machine. We had a Maytag machine 8 years ago where the board actually melted but like an idiot decided to try them again. I will never buy a Maytag again.

I really liked my Maytag Bravo X washer. Until, at less than 2 years old, it started having issues. It all of a sudden starting sticking in the spin mode, then it wouldnt turn off even though the cycle was complete. I have to pull the plug out of the machine it to stop from continuously running. I was charged $104 to have a certified tech come out for 15 minutes and recalibrate it and it worked for another month. It started having that same problem again and now, I have learned I need a new control board, which costs over $200, plus labor, over $60. The Maytag service rep I spoke with was very pleasant when she told me she spoke with her supervisor and told me there was nothing they can. So now I dont like my pretty new machine at all, and have to decide if I should stick almost $300 into getting it fixed again, or buy a new washer, NOT A MAYTAG! As I voiced my complaint on the Maytag website I saw that there were many of the same complaints about the faulty control board and am wondering what does it take to get a recall?

Three years ago, we purchased a gas Maytag double oven, it worked fine for three years, then it blew the breaker. When we turned the power back on, we could not turn the oven off. The control panel had to be replaced, dinner too. We had bought the extended warranty, so that was covered. Last week, after four months, it happened again. We placed an oven thermometer inside the oven and it is was higher than the maximum temperature of 600 which the thermometer could measure. We are currently awaiting a new control panel. Maytag used to be a good name, but recommend you to buy something else.

February 2011, I purchased a washer from Lowes and started having problems with the washer leaking and skipping cycles on the first week. Lowes exchanged the washer end of first week. The new washer started with not adding water in wash cycles. The repairmen sent by Maytag could not find any problem with the washer. The washer worked off and on for months with problems. Cycles with bleach added worked fine, but 3 or 4 loads later with no bleach having been added, it would produce bleach-stained clothes. The repairman came out again and could find the cause for skipping cycles, but suggested I run clean cycle every time I use bleach. It defeats the purpose of purchasing an HE water-efficient washer.The third repairman sat and watched the unit run a load and then he said I know what is wrong. He took the washer control panel apart and found the wire harness was not properly connected from tub to control panel. I have not found what causes bleach stains 3 loads after the bleach was put in the washer. I will not recommend this unit to anyone because of manufacturing problems with harness assembly.

My husband and I purchased the Bravos XL washer and dryer set about a year ago as our first big washer/dryer purchase for our new home. We spent about $1200 on the set from Home Depot. I very much regret this purchase as the washer never gets our clothing clean! The washer never puts enough water in the basin and the clothing comes out with strange white smudges EVERY. SINGLE. TIME.I have tried changing detergent, I have tried skipping fabric softener, Ive tried rinsing out the dispenser thinking it was residue from old soap. I dont know what it is, but what I DO know is that the clothes go in without the white smudges and come back out with them for every load. I have to run a second rinse cycle just to get it off, which means Im washing for at least an hour and a half. I DESPISE this machine and its costing me more on my water bill.Additionally, the dryer isnt much better. It constantly shuts itself off even when its not on energy saver mode, with the little red light going on for air flow. Ive checked the connection and dont see what the issue is. If I have a big load such as blankets in there, I have to dry them all individually for almost an hour just to dry my bedding! It simply wont stay on to dry a full load. I very much regret my purchase and wish Id gone with something simpler and cheaper as it would have done a much better job with my laundry. Lesson learned. Dont waste your money on Maytag.

At 36 months old, my Maytag refrigerator has already suffered from a Freon leak. After repair, the leak continued causing the fridge not to produce ice. After another Freon charge 7 days later, the fridge will freeze ice only in a manual ice tray. The water in the ice maker for whatever reason will not freeze? To make matters even worse, the freezer fan has been noisy for the last year. Maytags solution is to purchase extended warranty for $300 plus or hire repair person at $100 for first hour. A 36 month old refrigerator is in essence a disposable item. Basically for a $700 fridge… that breaks down to about $20.00 per month service charge and then it’s time to replace!

MF12269VEM7 - I purchased a refrigerator in September 2013 and my ice maker stopped working within 1 month of delivery. I had the motor and ice assembly changed 3 times and over 12 service visits within the first 6 months. I had the motor and ice assembly replaced in March 2014 and they offered to extend my warranty for a year. My ice maker has stopped working again. When calling Maytag customer service, I spoke to the Supervisor who will pay for the parts but require me to pay for the service calls. As well they only have a 6-month warranty extension on file. This fridge is obviously a lemon but they will not take any ownership because I did not purchase an extended warranty! The Supervisor state he does not report to anyone and he has the final say regarding my service. I will never buy a Maytag again. A year and a half of ongoing problems and no solution.

Well I have the washer and dryer. I love the dryer, it is excellent! Now on to the washer. It tries to save water so I guess people in California would love it. I have a laundry room in the basement and one up on the top floor with the Bravos in it. I only do the clothes that are not dirty but a little smelly in the Bravos. Any clothes that are dirty I do in my 20 year old machine in the basement. Do not purchase this machine if you are under 56 because you will need a step stool. Everything I wash I do on the longest cycle because the other cycles do not get all the clothes wet. Think about what I just said. The machine does not get all the clothes wet. Do not purchase this machine. I really cannot call it a washing machine, but they look real pretty in the laundry room.

My Maytag dishwasher which is less than 2 yrs old had its control panel and board gone bad. It took almost $400 to fix it. It seems like an ongoing problem and Maytag does not do anything. I would have bought a new dishwasher for that price, but I was already in for almost $200.00. They dont give you prices upfront.

We bought our Maytag washer and dryer a bit over 5 years ago. Now the UL warning comes on. Found out it will be over $400 to fix it. It only cost $500 new. Repairman says it is very common and not to pay him to fix it. Our GE went 20 years. Lesson learned, wife is out looking at new GE.

Just bought a Maytag Bravos 4.3 cu ft washing machine from NFM. The first machine delivered was broken it didnt wash or spin the clothes. NFM sent out another one at 9:30pm. It doesnt spin the clothes out well & loads have to be small. Poorly made.

We purchased a Maytag Centennial washing machine from a local business here in Knoxville in 2013. My previous Maytag lasted seven+ years and I was very happy with it. It began to leak water and after two times of having water on the floor, we decided it had worn out and purchased another washer. We immediately wanted another Maytag since our previous one has lasted for quite a while. We bought the new Maytag Centennial washing machine in the Spring of 2011. This is May of 2013 and we have had to purchase another washing machine since the electrical board in ours went out. The replacement part is listed at $300+ and that is without labor to install. Needless to say, I am very unhappy that I have had to purchase another washer so soon... and did not buy a Maytag this time.

I am also frustrated with Maytag for the same exact problem... The control panel and the dishwasher not working just after our year warranty went out. I purchased this product because we had a good experience with a Maytag Dishwasher lasting about 20 years, only to get fooled that the quality is not there any longer. This seems like BAD business on Maytag, Whirlpool, and Home Depot! How can we get an official complaint to someone who can fix this? Another example of big businesses that do not care to take care of customers! Why would a company like Home Depot continue to support this business!!

I purchased my Bravo (MVWB300WQ2) washer a little over two years ago. It took all day to wash some loads due to leveling problems. Example, you could not put more than two bath towels in at a time, even with the towel setting. The washer would stop and you have to re-position the towels. You cannot leave because it stopped so often. Also, the washer makes an extremely loud noise during the spin cycle. My most recent problem, it does not complete the spin cycle. My clothes are still very wet. I refuse to call service. Its just too costly. It would be the third time in less than 3 years. However, the first time was within the year warranty (no charge). The basket had to be replaced - it was ripping my clothes. During my second service call, the technician advised me in purchasing an extended warranty. I paid for the service call and for a one-year extended warranty which just recently ended. The washing machine is not worth paying for service again. I am going to purchase a new machine instead!

Purchased this unit back in November 2011. Sometime this year it started leaking water just like many others from the freezer unit onto the floor (many times large puddles). Im tired of the permanent towel on the floor to absorb the water to prevent a potential slipping hazard. I too went online and found a very nice video on youtube which showed how to disassemble the freezer compartment. Took everything apart and noticed that there was water frozen on the supply line. Melted this and put everything back together, for about a week there was no water leaking so I figured all was well. About a week later the puddle was back so I sent an inquiry to Maytag and let them know I had an image of the issue and asked if it was covered through manufacture warranty. Here is their response: Your email is extremely important to us here at the Customer experience Center and we sincerely apologize for any delays in responding to your email. We are working diligently to respond over the telephone and through email to all of our customers. We are sorry to learn of the problem you are experiencing with water leaking from the bottom of the freezer. Unfortunately, we are unable to determine from this location the exact cause of the problem. We recommend that you contact a certified technician for an accurate diagnosis. Once the problem has been diagnosed, please contact us back so that we can review the concern further to determine if assistance is available. For your convenience, we have provided below service providers in your area that you may contact for service. Aries Appliance Service (925)367-7708, Vigil Appliance Service (925)371-7701. You are a valued customer and we do apologize for any inconvenience this concern has caused. We invite you to contact Maytag again either by calling (800) 344-1274 between 8:00am to 8:00pm EST weekdays or by emailing whenever the need arises. When calling please press the available option or stay on the line to reach a representative.Frustrated I went online and found this forum where hundreds of other people had the same issue and that many of them were resolved by the new P Trap. So I watched another video by the same guy on youtube that showed how to replace the P Trap. I went online and found the replacement P Trap Manufacturer model # w10619951. One of the comments there actually said to call Maytag first as they were able to get a replacement P Trap for free. I believe if it was under a year old they would also pay for the labor to have it replaced. So this morning I called Maytag, the first guy Jim said I would have to have a certified Tech come out (76 dollar service fee, plus whatever the labor would cost) and Maytag would cover the cost of the part. I asked Jim if he could just send me the part and Ill do it myself, he reassured me that he could NOT do this and that the system was very specific. I told him I did not understand that a bad design and known quality defect, why should I have to pay several hundred dollars to fix? He told me that was the way it is. I asked to speak to his supervisor and put me on hold. Not only was the hold music extremely obnoxious but there was a loud humming noise as well, I waited for 10 minutes hung up and called back. I spoke with Maggie this time. I told her I wanted the part sent to me and if she couldnt help me I wanted to speak to a manager. She said she did not have the authority to ship me the part without approval. She said she could ask for approval and after waiting for about 3 minutes she came back on the line and said she spoke with her supervisor and that they would be sending me the replacement P trap today via FedEx. Had they not sent me the part my next stop was going to be the better business bureau..

I purchased a new electric oven/stove, dishwasher and over the stove microwave. My dishwasher didn’t work from installation and it took Maytag over a month and half to repair. My oven door hasn’t worked properly since purchased and finally broke and I have been without an oven for two weeks waiting on repair. The customer service does not listen to you and seem to be completely unconcerned about your problem. I was told the item broken was a common stocked item and the repair would be quick but that was not true. The repairman told me they would have my parts in a week and would install them on a Monday. They have now scheduled my repair for Thursday. Over two weeks with no working oven. I will never purchase a Maytag appliance of any kind due to the terrible customer service.

Maytag Bravos electric steam dryer purchased 2009 - I have had to replace the door hinges within one year of usage at my expense. The blower belt and pulley had come off twice, the last time about a half hour after the repairman (again at my expense) left. I put it back on myself and if it comes off again, I will use Locktite to glue it on the blower shaft. I figure I will be lucky if this crap lasts a couple more years anyway. No more Maytag for us! What does it take for the consumer to get some representation with regard to lemon laws here? I will take my wrath out on Home Depot here since I have no recourse. If enough people complain, maybe they will stop selling that junk. I also will disregard Consumer Reports in the future.

This dishwasher was here when we bought our home. It has been heating up way too much on the drying cycle. I turn it off and air dry the dishes but today I noticed it melted my plastic measuring cup. I had the heat turned off and opened it as soon as it started the drying cycle.

Maytag stove MGR7662WW - I purchased this stove about 4 years ago. Now, the stove will not light. I called in to Maytag only to be told I must pay a service fee or purchase a repair manual. It’s very strange. My old Kenmore lasted 22 years and here I thought Maytag would at least last 10 years less than half the life of my old stove, realizing products today are not what they used to be. Maytag, the dependability people, I guess that old Maytag commercial where the Maytag repairman is so bored claiming no one needs service for a Maytag product is really false advertising. Buy American products; I’m not really sure who is the current country who is home to the great Maytag corporation. I guess me and my wife will spend another $700 on another brand stove and try this process all over again, hopefully not again in approx 4 years.

I thought I was nuts - only 2 of water in a full machine of bedding or clothes. I agree with all the other one star remarks - clothes still dirty, still dry, hardly any water and if you use the bedding selection, it takes nearly 2 hours to wash a load and then it doesnt spin dry so you have to rinse and spin again. Very disappointed with the machine. Yes - class action lawsuit? How do we do this.

I purchased a Maytag French door refrigerator (model MF12569) two years ago. The bottom drawer freezer does not work well. Apparently, the inner tubing of the freezer clogs and it creates huge puddles of water. My floor got damaged and I keep calling Maytag and all I get is their apologies. I purchased an extra warranty which will expire on the third year. I am really disappointed with their product. I see why there are so many complaints filed and what makes matter worse is that they dont seem to acknowledge the problem. Apologies do not cut it. They need to do something to reestablish customer satisfaction.

I do not know how long we have had the Maytag but, it has been a long time and has run without any problems. Still looks good and does the job! The features of the Maytag are: pots & pans, temperature sense, sani heat, light wash, regular wash, pots & pans prewash, quick wash, rinse & hold, delay start and heat, fan dry, heat or air. This dishwasher has always been plenty big enough for our family of four including guests. This Maytag had a choice of black or white front so, it fits in. My next dishwasher will probably be a Maytag!

We purchased a Maytag Gas range MGR8674AB in November 2012. The contents of the drawer (oven mitts, trivets, hot pads) caught on fire. As we pulled out the drawer, it scorched the front of the range.

I bought Bravos xl. I hate it! Everything about it. It does not get my clothes clean and it ties load in knots therefore being off balance constantly.

One time at around yr 2 of our 10 yr warranty the repair guy removed my agitator, spline gone. Couldn’t find one anywhere! After a month of using a laundromat, I called the company in Montreal and they had the new agitator in my post office in 4 days. I am unable to wash anything that puts the Bravo washer out of balance ie: towels. The sides are busting out on the machine!! We have only had it 4 years so far. Not impressed! Does the warranty cover busting out sides? As it is a major part of the structure of the machine.

My wife & I purchased our Maytag dishwasher model # MDBH979SAB1 on 3/8/13 from homedepot.com. Approximately 24.5 months later our dishwasher experienced control panel light button malfunctions similar in description to the many other consumer complaints on this & other forums. I would like to share some additional information based on my research about this issue and possible fix. The source of Whirlpools control panel issue is design related. The issue is caused from moisture which induces oxidation on the Flexible Printed Circuit (FPC) cable that is integrated with the control panel and connects via connector to the electronic control box. The issue usually manifests itself on the cable just where it bends coming out of the touch membrane panel.The oxidization of the FPC cable eventually creates electronic shorts or opens between the parallel traces thus causing the panel control lighted function problem which disables the dishwasher from being used. The cable, since integrated with the control panel, is not a separate replaceable part. In order to repair, the Whirlpool diagnostic action is to replace the entire control panel. I quickly learned after doing some online research about Whirlpools control panel issue that it extends back to at least 2011 with control panel part # W10475784 and corresponding or like PNs of this design. The number of control panels sold of this design by various online appliance part centers coincide with the high number of reported like control panel failures.In just 2015 alone so far, the sales for this control panel have been in the hundreds. This indicates that Whirlpool continues to replace defectively designed control panels upon failure with defectively designed control panels. There was also a class action lawsuit filed against Whirlpool in the state of California on May 6th, 2013 for the control panel issue. The filed lawsuit is public & the whole document is available online as a pdf file. Unfortunately, Judge **, granted Stipulation to Dismiss Case with prejudice 74 on 5/23/14. I was unable to find out any details as to why the case was dismissed. I did not call Whirlpool about my control panel issue, instead I handled all correspondence through Email to them at WHIRLPOOL_CUSTOMEREXPERIENCE@WHIRLPOOL. COM.My initial correspondence included all the facts about this issue & that I did not wish to have their warranty coverage/period explained to me for I understood them, the problem was a quality issue, and just basically wanted to know what they were going to do or have been doing about resolution. The email correspondence with them got me nowhere. They initially replied back with all the form niceties like We apologize, We understand your frustration, & We value you as a customer, but denied every knowing about such control panel issue, regurgitated their warranty policy & period and were unwilling to resolve anything. In their last reply they stated how unfortunate it was that customers only take the time to provide negative feedback!! This is just bad business, and though I would not like to think it, but the control panel issue may have been by marketing design.Please keep in mind that Whirlpool manufactures appliances under at least 15 different name brands including Maytag, Kenmore, Admiral Kirkland, KitchenAid, Roper, Speed Queen to name a few. All is not lost, being an electronics engineer I looked into the do it yourself fix. If you are not comfortable in doing this, you may be able to find someone to help. I was able to repair mine by carefully scraping off the oxidation from the FPC cable (will appear brown in color) & encapsulating it with high density 100% dampening silicon (non-caulk type) to protect it from moisture & withstand heat. There can be other ways of protecting it from moisture instead of silicon, just make sure it can withstand heat, wont become brittle, & that it may not cause potential damage to the cable itself.My repair has worked for about 4 weeks now, & shows no sign of oxidizing. The problem may be more severe if the oxidation has actually opened or broke one or more of the small cable traces. Do not attempt to solder this cable! Its way too thin & will only make matters worse. An open can be carefully bridged with a conductive glue or ink thats on the market. One source is a window defogger repair kit product thats sold at auto stores that has a conductive glue in it. Post open repairs will need to be checked with an ohm meter to make sure repair is good and that any adjacent trace lines have not been shorted by repair. Of those of you that have just bought or had installed Whirlpools defective control panel, please encapsulate the FPC cable as soon as possible to protect it from moisture. If you dont, it will surely oxidize again over time.

This washer sucks so bad. Just got it a few hours ago and its absolutely horrible. The water just runs for the wash cycle. And I was told by the salesperson at Best Buy that it would save you water. Thats not the case. There is enough water to run over all the clothes. It doesnt agitate enough to even move the clothes around. The clothes basically sit at the bottom of the tub in the water doing nothing. This Maytag Bravo washer will be returned tomorrow. Me and my wife are highly disappointed. I wouldnt recommend this to anyone. Weve decided to just get the old washer fixed and go from there. There are too many bad reviews for this washer to still be on the market. We feel that this was a total waste of time, energy and money.

I have a Maytag fridge/freezer model number MFF2557 10403089ER. The freezer keeps going out. The repairman replaced the computer board called a jazz board stating that the bulbs in the fridge part are too close to the board and the heat can cause the board to short out. He suggested switching bulbs to 25 watts which cannot be found for fridges. The freezer continues to go out and sometimes restarts itself or by flipping the breaker switch, brings it back. In the meantime, food is ruined. Yesterday, he put a new starter relay on the compressor stating that this series of fridge/ freezer has had a problem with the compressor and Maytag will not take responsibility for this. There is no recall at this time and we are waiting to see if this corrects the problem or if the freezer will continue to go out. Thank you for your help in this matter.

Bought refrigerator 2012 from Home Depot (model something like MBF1953YEB - how sad is it that I now have this number memorized?). Freezer too cold, refrigerator way too warm. Freezer air ducts frozen over. Tried manual defrosting twice per YouTube suggestions. Finally got repair for $400!!! Thats about half what I paid for it! One proponent repairman stopped me mid-sentence when I said Maytag saying, I know what it is. The computer (Jazz?) board needed to be replaced for $217. I just looked up Maytag to see it was bought in 2006 by Whirlpool. So I wont be purchasing any more Maytag or Whirlpool appliances.

This is an awful product. I bought this product from Best Buy at the beginning of August 2018, and can no longer return it because it’s past their 14 day return policy. This washer does not wash clothes well. No matter what setting it’s on, clothes come out looking dirtier than prior to washing. Maytag should do what is right and refund customers for this worthless purchase.

We purchased our Maytag Bravos XL last month and within two weeks, we were noticing a BAD odor every time we used the machine. In fact, I just walked back into our house from outside and the entire house smells like old dirty dishwater and the smell is coming from the laundry room! This is a very expensive washing machine and we bought it because we thought that a Maytag would be better than the Whirlpool that just died after many years of repairs and aggravation. After reading these reviews, I wish I had bought a Speed Queen.

I purchased the Maytag Neptune pair in 2002 and was never informed of the product recall/class action lawsuit for the washing machine which occurred sometime around 2004-2005. We have had many problems with our washing machine over the years and ruined many clothes with what appears to be bleach stains, even though no bleach was used in the cycle of wash. I had to replace the board which controls the latch on the door and the clothes that are washed are not clean and have an undesirable odor to them. I would have been part of this class action; however, I was never informed of the lawsuit. I called Maytag today and they advised I could set up an appointment with a service person; they did not want to honor my complaint as the class action lawsuit has been resolved and they are not handling these types of complaints anymore. My children have started a new school after semester break and their brand new uniforms are now becoming ruined due to this defective machine that Maytag will not take responsibility for. What type of recourse do I have? I will never purchase a Maytag anything if this is how they treat their customers. Problem will not go away by hiding their head in the sand. Now I have to go out and purchase a new washing machine because Maytag didnt inform their customers of the inherent defect in their product and take care of them accordingly.

I was having similar issues with my Maytag model MD dishwasher. The unit was operating, and then the start/resume light began flashing. Didnt think much about it since the machine continued to run. But the machine wouldnt cycle off, or rinse or dry. It continued to run, with the start/resume light flashing. When I opened the door and hit cancel, the unit turned off. Several minutes later, the normal light and heated dry lights came on, and soon after, the unit started up by itself (Twilight Zone music is going off in my head). I let it continue to see what it was going to do. It ran, and ran, and ran some more. I stopped it and secured the power to it, left the power off for a very long time. Started it up, no joy.I began reading the blogs sent in by other frustrated Maytag owners, we are numerous. I went back and re-read some of the posts that dealt with resetting the control panel. The one that mentioned; press Hi Temp. then Start/Resume about 3 times consecutively, that did the trick. Thank you for that useful piece of info. Saved me 143.00 plus tax and shipping for the new control panel (for now). I found some very helpful MOs (Maytag owners). I also found something very frustrating, with so many unhappy customers dealing with the similar issue. I would think that Maytag would put out a technical alert that deals with these problems. Instead, we get these so-called Maytag experts that magically appear on your computer screen. They ask you, what seems to be the problem. So after I described the issue, I asked the Pro, how to prove that the issue is with the control panel, or the elect. control board, both parts are 143.00 ea. (Just trying to limit my pain.) They send me to a page that wants to charge me 28.00 for the answer. What an insult. We pay 500-800 dollars for these units that should last more than 4 yrs. and some doofus is charging you for answers that saves you the consumer money and frustration. I, like many in the Maytag blog, will never purchase a Maytag product again.

We spent $600 on a Maytag Jet Steam Plus dishwasher and its junk. We bought it in May of 2013 and the top panel is burnt out and the ribbon or control wires is corroded. Maytag wont pay for replacement parts and I wouldnt recommend anyone buy Maytag again. I thought it was supposedly a good brand but its nothing but garbage.

I moved into this house and the dishwasher came with it. For an appliance that is over 8 years old it works beautifully. It cleans my dishes well and doesnt leave residue on them. I ran it through a cleaning cycle recently and that has only improved its performance. I recommend dishwashers by Maytag because they last and perform well.

Less than 2 yrs old and starts giving UL error on spin cycle. I try replacing the springs. No relief. Notice dark brown fluid under dryer. Thing sound like a plane taking off. A little more research and Im thinking its the bearings. Looks like an expensive repair, now I have to decide whether to cut my losses. Seriously? The reviews on here are just horrible, not like this was an dl hell machine.

I take pride in my cooking and love my kitchen. As you know this is where everyone gathers when you are entertaining. The Aqualift system does not work. I have run the process 3 to 4 times consecutively in row and the inside oven the oven is never clean. I wipe out the sides over and over. So disappointed. The only saving feature is that you can not see into the horrible look of the inside the oven when it is closed. Was this feature really tested before it went to market????

I wish we would have never bought this brand and model. Within a month there was a loud banging and the serviceman came out and changed a valve out but it just got a little quieter but never went away. 2nd issue is cloths ball up when your doing bedding. Not sure if they are really clean or not. 3rd when we take the cloths out of the washer we are still seeing soap spots where they were not rinsed very well. We are using the right soap Gain but we cannot wash cloths in the bedding setting. We have to use the extra rinse setting to get all the soap out which defeats the whole savings issue of this machine. It says when you do your monthly machine cleaning it resets the water level but there never seems to be enough water in the tub. Also if your doing sheets in the washer and when the spin cycle starts you have to hold your breath to see if its going to get out of balance which it does 50% of the time so you stop and move things around. Also we cannot put a whole lot of cloths into this big drum because they dont wash correctly. Worst purchase we ever made. With all the negative reviews you would think that Maytag would come out with some fixes but I dont think they really care anymore.

We spent over $1,200 on a Maytag washer on 12/2015 and it did not work properly. The door got locked, had a couple loads moldy because we could not get it open. Didnt drain either. Maytag had someone come look at it 3 times and it still didnt work. Called Maytag and now they told me that they cant do anything about it because is not under their 1 year guarantee. And of course they are very sorry for my unfortunate inconvenience. I thought they had a good honest reputation but... Im just disappointed!

My dishwasher is less than 2 years old. Dishwasher will go on when we are not in the house. Cant control the panel. The control panel lights all come, have to cancel to stop the machine. This could be a fire hazard.

MBD7709AWB2 - Bottom line, every 1.5 years (18 months) you will have to buy a control panel. Number 3 for me cost me $149.00. Now my wash cycle will not kick on. Do I have to tell you what dishwasher not to buy!

All of a sudden, the lid lock light is flashing. The washer is only 1.5 years old!

Purchased a Maytag based on previous models that worked. Now when I do a load of wash, no matter how large or small, the clothes are still wet after the full spin cycle is finished. This has been going on for a few months. There are only two adults so the machine is not in constant use. We have had the machine 9 years and frankly would never buy Maytag again.

Apparently the Maytag Bravos HE top loading washer is poorly designed. We have sparingly used this washer for approx 3 years and it began to make a horrible noise in the spin cycle and then to give us UL error codes. After searching on the internet we discovered that the seal around the main spin shaft and the bearings were bad. Inspection under the machine revealed a terrible rust and grease spot and splatters of rust and grease on underside of unit. This is a typical problem and this machine should have been recalled or at the very least repaired by Maytag for little if any cost. They now make a kit to fix this problem, but this should not happen after only 2-4 years of use on a $700+ machine. Very, very disappointed with Maytag! Customer service, of course, offered us nothing as pathetic 1 year warranty was expired. Ten year on the tub, like anything will go wrong with that.

Ive had this Maytag for more than 15 years and it still works well. Its a basic fridge, no special features. Just keeps food cold or frozen. Freezer at top, fruit & veggie bins at bottom, cheese bin. No problems, good performance.

Im writing in reference to Model # MF12569YEM2. Bought this 3 years ago for close to 3k. Since then it forms a sheet of ice under the bottom freezer and leaks water onto the floor. It has ruined my hardwood floor and leaked through the floor to my basement and now need to re-sheetrock the ceiling. Its a bad design and should have been recalled because I see everyone else with this model is having the same issue.

H.V. Board failure on Maytag model #MFI2568AES refrigerator. Whirlpool needs to step up their parts program. This refrigerator has been down for over 6 weeks and part will not arrive till 7/10/14. There is no excuse. The Maytag name is about as good as our country gone to H_ _ L in a hand basket. Consumers should not have a wait on parts or repairs that forces them to buy a new appliance when they spend $2500 and it only last a few years and try to contact them, they wont reply. I hope everyone who reads this considers LG, GE or SAMSUNG and not whirlpool excuses and JUNK.

Quiet, well priced and reliable technology which makes owning this dishwasher an easy buying and owning experience. Having the brand backed with great reliability and if needed excellent service makes the buying decision easy for the consumer.

Loading is easy, operation is extremely quiet, dishes are very clean even on normal auto wash cycle. White, integrated depress buttons, full size, removable utensil baskets, upper and lower racks, top rack is manually adjustable, stainless steel tub. White front which is what we want not the ugly old metal stainless steel, usage buttons are on the upward facing edge of the door, pull down handle is nice size and very sturdy. Model is MDB8959SBW3. Even on normal auto wash cycle dishes are clean without much pre-rinsing. Purchased 10/14 from local dealer and professionally installed. So far we love it.

One year and 1 month after purchasing dishwasher, the lights on the control panel would move around and if I close the door all the way it will begin to wash. I have not contacted distributor about repairs. After reading all the reviews, I think I will just use it until it quits. Will never buy another Maytag.

I have had 2 Maytag washers in 37 yrs and loved their products, however I purchased a Maytag quiet 300 in 2/09 and it is the worse Maytag product on the market. The frame around the bleach dispenser has rusted out and I have called for the 3rd time in 5 years to have it repaired. To my dismay it will cost 300.00 to fix because the bearings have to be replaced. I will now have to purchase a new washer. The days of the Maytag man are long gone. By the way the Maytag dryer has been serviced twice. I thank God everyday for that extended warranty I bought, but now it has now expired.

Very easy to use- just dial the button to the load of your choice! The only problem I have is it becomes unbalanced sometimes on a heavy load. :( And it is also energy efficient and lets you know when it needs cleaning.

Can not wash 4 pairs of pants or 2 sheets because they get out of balance when the spin cycle begins. I had to take the clothes out and move them around to keep the balance. Very unhappy. Would not recommend this washer.

First Maytag washer we bought in 2003, worked flawlessly for 14 years, bought a new one in 2017 only because my wife wanted a bigger washer. Bought a Maytag top load MVWB765FW0. What a big mistake. In less than 3 years it has failed already. The water inlet valve went bad. Maytag offers no tech support because they want to charge you with a service call. I found out what was wrong by researching the problem and error code online and bought the part for $55.00 and fixed myself instead of them charging $100.00 just to show up at your door plus the part and labor. A washer failing in less than 3 years is totally unacceptable and I will never purchase another Maytag/Whirlpool product ever again. Someone needs to wake up at Maytag.

I went to Home Depot in Kennesaw, Ga to purchase new W&D combo. I had found what I wanted but when the sales went to complete my order, the units I selected werent available. She talked me into the Maytag Bravo, but I specifically stated I needed a large tub because I wash a lot of towels and sheets. Well this expensive piece of shhh, doesnt even get all the items wet. Ive had to lift the lift and physically flip items in tub, especially with towels and sheets. Also, the washer is loud, did I say loud, I mean freaking loud. The dryer is fine, but I bought combo for a reason... Pricetag $1200.00 with my discount. I waited a week for delivery, I am mad as hell. Whats point of having large tub, when you barely get enough water. Luckily I found out now, so I can have them pick this CRAP UP, Do not buy. Theyre cute looking, but washer does not get your clothes clean.

We purchased a Maytag Commercial Technology washer from Lowes. After having the washer for only 3 months, the drum failed, an entire load of clothes was turned black with oil, and my washer was out of service for months. The drum had to be replaced. They did not offer me a replacement. I was just without a washer. They couldnt get the parts because of supply issues created by Covid. I was offered a 2-year additional warranty which should have carried me through 2022. Last week, I called to use the warranty - service was scheduled (and I was told that I did indeed have a warranty by the service team.) I was then told by the repair team that I was out of warranty. Maytags notes show I was only offered a 1 year additional warranty. I talked with Management at Maytag/Whirlpool - they will do nothing for me. Shame on me for not getting that in writing. Shame on Whirlpool/Maytag for lying to me. The washer has been a nightmare! Dont buy one.

I received my Maytag dishwasher in November of 2013 from Home Depot (It was a month overdue the expected delivery date). It was installed by a certified electrician/contractor. By February of 2014, the control panel had to have its first replacement. It is now July 2014 and we are having the repairman come out to replace the third control panel this Monday. Supposedly there was a recall on the control panel and the one replaced less than a month ago was the improved/repaired one. We are beyond frustrated. I too sought Home Depot for help after the first repairman they suggested charged us almost half the cost of the dishwasher for his repair. I have already sunk over the price of the product into repairs. My Maytag dryer broke last week as well. Someone needs to get involved with this situation, perhaps a contact to the media? I think we are all being scammed and deserve refunds by Maytag for the dishwashers and our repair costs.

I owned an front loading Maytag Neptune Front Load Washer MAH5500 for more than 10 years and first 5 yrs doing 2-3 loads a day for a family of 12 so this machine held up well, and only issue we had with the machine was the rubber around outside needed to be replaced after about 9 yrs.

I have owned this dishwasher about four years. After about three years the control panel malfunctioned and had to be replaced. Six months later I had to replace the controller. After another six months the control panel has again failed. Rather than invest more money in this beast, I have decided to replace it with what I hope is a more reliable machine. This experience has definitely put a bad taste in my mouth about Maytag products. I’m afraid this will be my last purchase of a Maytag product.

Ive owned the stainless steel version of the Maytag dishwasher model MDB7749SBM purchased on Sept 6th 2013. July of 2014, my first control panel went out. Lights not responding. Was within the 1 year warranty period. Now, that panel is acting up again. I called Platinum Factory service and they wanted to charge me for a new panel and the labor. Well, I used a few choice words on how I felt and the customer service person said the part would be free. Well, nothings free as I scheduled a visit by the Platinum Factory Service. They of course call 5 times to make sure you are home. The day of the service, the tech calls me to see if Im home. I of course said I am... then, he goes to tell me the labor charge for him to come out and hourly rate will come to $189!!! I said screw it and dont bother. Maytags quality and engineering SUCK. Avoid them...

The refrigerator works well. No problems. Easy to move to clean behind it. Good value. I havent had any problems since I bought it. Keeps a steady temp; Its exactly the size I needed; has plenty of space. Its a plain fridge with a reasonable price!