I purchased the matching Bravos Washer and Dryer in April 2010 at Lowes. I also purchased the extended warranty to have coverage for 4 years after purchase date. I noticed the dryer sensor is not very accurate. The purpose of the sensor is to detect when clothes are dry and then end the drying cycle automatically. However, it fails in both ways. When the dryer stops on its own, the clothes are still damp. I have the setting on NORMAL>LOW HEAT>NORMAL DRYNESS (the reason for the low heat is not to fade/shrink clothes) and even though the heat is on low, it should still keep running until the clothes are dry. So when I open the door and feel the clothes, they are still damp; I turn it back on to run again. If I dont check on it every 10 minutes, the dryer just keeps running and the clothes are bone dry. The sensor should detect this. Once, I decided to test it to see how long it would run with dry clothes and it ran for an HOUR before it shut off. Talk about a waste of electricity.The washer also has issues. First is the SHEETS setting. This setting is supposed to prevent sheets from tangling/balling up. Every time I use the sheets setting, my washer stops with the UL error - uneven load. Meaning, I have to babysit the washer because otherwise, it will stop and wait until I pull out the sheets and loosen them up. I am only washing 1 fitted full size sheet, 2 flat full size sheets, and 4 pillow cases. The reason I bought this machine was because it is supposed to handle king size bedding. Apparently, this washer cannot even handle full size bedding and I refuse to wash each item individually - the machine is supposed to save energy, not require extra loads. The second issue I am having, which resulted in me calling to utilize my extended warranty, is tiny rust dots on my clothes! About 3 months ago, I noticed one of my t-shirts had 4 tan spots smaller than the size of a dime. I assumed I spilled something on myself. About a month later, I noticed it was on another top. Then I assumed it was something on the back of my chair at work causing the spots. It seems to happen every couple of weeks because another article of clothing had these mysterious dots on them. Once, it appeared on my towels and sheets. I realized it was not me spilling anything on myself, nor was it from anything on my chairs. Now, I wasnt sure whether it was the washer or dryer, but I noticed when I pulled out a white sweater from the washer, there were 3 dots on it in the front, and I definitely would have noticed these before, which is how I came to the conclusion it’s from the washer. I cannot see any rust inside of the washer basket so I dont know where its coming from, but I am certain it is not from other articles of clothing (such as zippers or snaps); and the reason I know this is because I do not wash towels with clothes and also, I am 8 months pregnant and have been wearing maternity clothes for the past 5 months and they do NOT contain any zippers or snaps. I took pictures of the rust stains on various items and combined to 1 image. Now, I called my extended warranty to have a service technician come assess these three problems. Well see what happens.

Only 2 months after purchasing the Neptune Washer I required a service call as the washer was not draining. Technician replaced the pump and cleaned the drain filter. 4 months later the same issue happened. 3 months later the computer board was replaced and filter cleaned. Since purchasing this washer I have had to have 5 service calls to have it fixed. I called Maytag and they told me it is my fault the filter is clogged. Although the things in the filter are from my familys laundry the filter is located in the middle of the machine which requires the machine to be torn apart to clean the filter. This is a TERRIBLE design flaw which is NOT covered under the maintenance agreement as the service technician said this problem was caused by us. Maytag was the absolute worse to deal with as I have spoken to two levels of customer support managers and all of them said its my fault.

We bought this Maytag Bravos 300 Quiet series top loading washer 3 years ago. Maytag was always the top brand to buy so I thought it was the style washer but now I believe Maytag has failed to keep their standard of quality high. My clothes come out of the washer almost dry and full of lint. Even though I use the HE wash soap, it does rinse out of the clothes. Dark clothes come out with a noticeable scum so I suppose the lighter clothes do, as well, I just cant see it. I always have to double rinse them which defeats the whole economy issue. Im not happy with this washer and would not recommend anyone to buy a Maytag brand washer. I absolutely HATE this Maytag Washer. DO NOT buy it. I would rate it less than one star however they did not offer a 1/2 star. If there is class action lawsuit please include me.

I purchased a Maytag electric slide in stove, in stainless steel. The aqua clean is a joke, ran it for three cycles after cooking one roast and it does not work. Then to add insult to injury I had to get on my knees using a turkey baster to remove what was left of the two cups of water. The finish on the front is coming off. Not at all what I expected from a 1500.00 range. Poor quality. Now there is the sound of a fan running and I am not using convection.

I purchased a Maytag Washer & Dryer Bravos XL in 2013, the washer is already in the junk yard, the drive system failed, the bearings failed and it began to leak. The dryer had a main control board failed, I was able to purchase a new one and replace it myself. The board was made in China, the machines were assembled in Mexico. I replaced the washer with a heavy duty Speed Queen washer made in the USA!

I had a Maytag dishwasher (made by Whirlpool) that after 4 months of ordering wrong parts, parts arriving damaged, and parts that were re-engineered and did not match up, the dishwasher could not be fixed. The extended warranty people (AIG) promised me twice on a recorded telephone call that they would exchange my dishwasher, and after many many heated telephone conversations was given a 20 minute lecture on how the word exchange does not mean they will replace it. The frustration ultimately overtook my misspent loyalty in anything made by Whirlpool and I decided to accept the buyout of my extended warranty contract, at a loss of hundreds of dollars to me - well worth getting rid of that dishwasher and any further affiliation with Whirlpool corporation. Absolutely horrible customer service. Unbelievably god awful treatment. I dont know what happened to customer service at Whirlpool, but my dealing with them has convinced me that the term is an oxymoron at Whirlpool. Horrible horrible customer service. I have never been treated so poorly in my life. I truly dont know how they can still be in business if they treat their customers like they did me.

Maytag bravos xl - HORRIBLE at washing and cleaning the clothes. Broke a little after a year... Went to Maytag site, saw that they push 10 yr warranty. Transmission went out... but not covered?? Garbage.

The cost was right for the quality of the product. Brand was also a factor. We have had no problems either machine, both work as expected and have fully met our expectations. We recommend these products. Energy efficiency, ease of use and capacity were all considerations in making the selection we made. Maytag continues to hold a good reputation. Regular repairs, low quality construction and a cheap finish which looks tacky and is also difficult to clean would each be deal breakers. We purchased our full-sized, side by side Maytag Neptune Washer and Dryer gently used from a private party who needed to obtain different models due to a remodel of their laundry/utility room. We paid about $600 for the pair.

Dishwasher control board - This will be the 3rd time for this same failure with the start/resume button on control panel. Obviously, with all the complaints regarding this part indicates manufacturing is producing a defective or inferior part. The service provided by Maytag, which is supposed to be a reputable company, is a joke and non-existing. Like many others, here I will gladly be part of the class action suit and will never buy another Maytag appliance and will also inform others of their poor service.

We purchased a Maytag refrigerator, model #mf12269veb on 2/1/12 and for the past few months it has been leaking water out of the bottom freezer unto my floor and ice is forming inside the bottom of the freezer. I have read many complaints about this and if there is any recourse to this problem please let me know. So disappointed with this appliance.

Same as all the other reviews control panel intermittently started to fail. Dishwasher is less than 3 years old. Does not work at all now. I tried resetting circuit breaker - nothing. This unit was $700 from Home Depot. Complete trash. It is cheaper to buy new dishwasher than repair - how unfair! Maytag won’t repair - well for over $300 they will. I feel better knowing everyone has same issue & is not my electrical system. Class action lawsuit!

We first purchased a Maytag Neptune washer and dryer set. We loved them. Had them for 15 years with no problems. When we decided to get a new washer and dryer, we were loyal to the Maytag brand. I was immediately drawn to the Maytag Bravos XL due to the extra large capacity. What a mistake! This washer and dryer pair take more than two hours to complete a single load of laundry. It often takes more than one wash to get clothes clean. If you wash an extra drum large load of laundry, often times there is not enough water and agitation to even get all of the clothes wet. I have a one-year-old boy and a six-year-old boy, their clothes get very dirty. This washer Does not get food off of my one-year-old’s bibs. And my six-year-old’s clothes come out looking as if they haven’t even been washed. What a disappointment! My husband and I are going out today to purchase a new washer and dryer set after having just purchased these Maytags in April last year. What a waste of money! Please include me if a class-action suit it’s taken.

It’s the worst washer I have ever encountered! I never have clothes that smell clean. The water seems to never completely spin out, the spin cycle is terrible!!! My whole house shakes when it’s spinning and the noise coming from it is so loud. The time on it is never correct; it will say there is 9 minutes left and then just go to 1 and quit! My clothes have never looked clean with this machine. And yes, I use very good detergents and everything else to try to help with no luck! The dryer just takes forever to dry anything. Needless to say, I will NEVER purchase another Maytag again!

Purchased a Maytag bravo washer model #MVWX500XLO 2yrs and 6 months ago April 28/2011. In Dec. 2013, I heard a loud clanking sound and was shocked. I thought that some coins were lodged somewhere.... not the case. I put up with the clanking until after Xmas.... Finally I called a licensed technician (in business more than 20 yrs). He immediately identified the problem.... THE TRANSMISSION was shot. Wow what a shock! 65.00 dollars house call to give me the news. I phoned head office to no avail. The office said that it is not covered and that the part would be in the neighborhood of 350.00 $ and probably the installation around $160.00. I am still in shock. We paid around $750.00 for the unit. The technician said that it is one of the worst machines he has ever worked on. I am now talking with Home Depot to see if they can get some compensation on the unit (speaking with the rep). Will I buy another Maytag (by the way) made by Whirlpool... I guess not.

My original Maytag washer lasted over 25 years (still using dryer purchased in 1977). But the Maytag model SAV 4655AWW I bought a few years ago is a piece of junk! Not long after it was out of warranty, it started making noise. Not overly loud, but noisy. Since then, though it makes such a loud noise, you can hear it 3 rooms away. It leaks water from the seals, shakes and vibrates all over the place (even when level). The rocking appears to be due to pathetic self-leveling legs they put on the back of the washer. I had to put a 2x4 on the back side of the washer to keep it stable. That took care of the rocking, but still noisy, leaking water and now it gets off balance when spinning and stops. It also wont start sometimes and you can smell it overheating. The transmission is now going out of it. This thing has been one issue after another. What is worse about it is I saw in another forum that this washer wasnt even made by Maytag. Supposedly Maytag bought? After the purchase, they just put their name on it. I bought a Maytag because of the dependability of their previous products, so Im thoroughly disappointed in their company and products. If I had wanted a washer built by some other company, I would have purchased it versus theirs. If you purchase a Maytag, you expect to get a product designed and built by them. Ill never buy another Maytag product and Ill thoroughly research the product Ill buy to replace this hunk of junk. My advice would be dont waste your money on Maytag.

Purchased 4 Maytag kitchen appliances - stove, double oven, fridge, dishwasher - was told that they were all made in the USA. WRONG. The microwave comes from China - not sure why Maytag is not being honest. Not happy with my purchases - even though we spent $4000 to buy American. Warranty service is awful - even extended warranty is a joke. Would never purchase Maytag again.

On the first day, first time, the washer wrinkled clothes so bad I could not get them out. I talked to Home Depot people and they said I must lay clothes around tub like pictured in the book. I did that and they were still wrinkled. I called the repairman who said nothing was wrong with the washer. I talked to Home Depot; they did not have the answer. I called the repairman and he checked it out. He found nothing wrong. He did watch it washing and said he had never seen a washer tangle and twist clothes like this before, called Maytag. They said that I was loading clothes wrong, and nothing was wrong with the washer. They would not give me a number to call above them. This washer is bad. Maytag has known it for 4 years and done nothing about it. Ive been ripped off.

I sent an email to Maytag regarding my Maytag Bravos washer which I purchased two years ago at a cost of $1,100. I have started having problems with the machine last week. I kept getting the UL error code. I called a certified appliance person to come out to find out what was wrong. I do not believe any of the appliance people know what to do for these machines.First, I was told it was the control board that needed to be replaced, then I was told the motor had a crack in it and it needed to be replaced, and then the springs needed to be replaced. So they replaced the springs. This was a Tuesday afternoon. It worked fine until Wednesday of the next week and I started getting the F51 code. Just let me say if you cannot stand behind your parts on a $1,100 washer that is only two years old, then something is very wrong. I am in for $159 on repairs so far. Who knows what the cost will be to finally get the machine repaired.

Maytag Performa Side by Side fridge PSD262LHEB door handle pulled off for the second time since purchase but this time, the handle knocked over a pot of hot water on me. I am just relieved that I have no small children anymore. I would consider this very dangerous in any household. The first time, it was covered under warranty along with the broken ice maker. The repairman stated that he had replaced many handles and due to design flaw, they would not last long.

The worst washer I have ever purchased. Clothes DO NOT come out clean, smell musty after washing. Have even decreased the amount of clothing per wash. Cant use bulk load function: throws LF Code - Bad water valve. I will NEVER buy or suggest anyone buy this piece of JUNK! Then to top it off you have to constantly chase the machine around due to wash load becoming unbalanced. Now today have to contend with a burnt smell...

Front load washer. When load is done. Removing is one long string of clothes... Is a large load washer which I like. But you cannot add any items after you close the door. And you always forget something that needs washing.

I bought a Maytag Centennial Top Loading washer 2-1/2 years ago. Its worked very well, but has started to roar so loud on high-speed spin that you have to leave that side of the house to be heard. The factory technician determined that it had a bad gearbox and that it wasnt anything I had done that caused it. He told me it was going to cost more for parts & labor than the machine was worth. I called Maytag and was told they wouldnt help me because it was after the one-year warranty. When I asked for a supervisor, he offered to pay for the parts, but not the service. Thats kind of like Chevy offering to pay for the defective engine part, but not the installation. I have never bought a major appliance (or even a hair dryer) where I thought 3 years was a reasonable life expectancy. Lifelong Maytag Customer has left the building.

Our washer, still under 5 year parts and labor warranty, wasnt functioning properly. We went through proper procedure having repair personnel first attempt to repair; waited over allotted time for replacement parts, wanted to attempt to repair again, then to replace with sub-standard model. We are now in our 5th month of being told 3-5 business days, 10-14 business days, and I was just told it will be weeks (after waiting 19 days) that replacement will return our call as they are 4 to 6 weeks behind. I have pages documenting dates, times, names, departments and excuses. What can I do at this point? What are my options?

The Maytag Bravos Washer we bought had a stinky odor we couldnt get rid of. We found that clothes had gone over the basket and lodged in the filter above the pump; end of stinky smell. Later, we found that pennies and other small items had slipped into the fins of the drain pump and ground them off. The filter does not keep out of the pump and is not made right to stop damage. I called a local Maytag dealer who said he had a lot of similar complaints. I called Maytag who stated they have no registered complaints of this type and had no fix for it. Avoid the Bravos line of washers - they are not made right and Maytag will not admit it or help you. Bravo for Maytag who are obviously not going to act on it. Make a formal complaint and find if someone has a lawsuit you can join!

I reviewed lots of reviews, and decided that the negative reviews ones were sour grapes or uninformed customers! WRONG! Do not buy this washer. I replaced a 16 year old Frontloader Bosch! Should have had the Bosch repaired, but wanted a topload for a change, new look etc. From day 2 the washer began to squeal during the early cycle and at the end as well. Maytag repair was out for an unrelated repair on another appliance. I told the tech about it and he suggested its brand new etc, give it time to settle in.Now 4 months in and another service call to tell me its nothing!! It squeals so loud I can not run it while in the next room. I have videoed it and sent it to the Maytag repair in Glenwood Springs, and he said I should load it only full enough to see the impeller at all times!!!! Forget a full load of work clothes or a pillow or blanket. Which is to be expected to be able to wash. He said I needed to spread the clothes out manually along the outer sides of the TUB only, prior to washing the clothes! not over the impeller. I am not kidding! This is a open tub, so the impeller is the little thing in the middle on the bottom. I advised him, I videoed the event and even with three socks in it for a test it still squeals like a (well you get the idea). Trying to get Maytag help, but nowhere. Matching dryer door hinge broke first week, it has been repaired. Not good quality at all for the top of line Maytag. Then Maytag Man must be busier these days, than of old.

We purchased a Maytag Jet Clean Plus in August of 2013. Within 8 months the control panel stopped working. Though it was replaced by one of their technicians it now after 9 months is broke again. How can this be such a crappy product??? Over 800 dollars for a dishwasher to have to go out twice in less than 2 yrs is just wrong. The company needs to stand behind their products!!! I will never buy Maytag again and will advise anyone looking to not waste their money!!! VERY DISAPPOINTED!!!

Purchased French Door MF12269VM 22 inch from The Brick furniture April 1, 2012. Turned out to be a real April fools joke. Purchased extended warranty with TransGlobal for 5 years. First, fridge delivered after about a couple of weeks because it actually wasnt in stock. Naughty Brick lied about availability. Fridge arrives and after a service call from Maytag repair, they ascertain compressor doesnt work.Order fridge number 2. Two weeks later, get second fridge but lever for dispensing water is broken off. Order fridge number 3. Usual two-week wait and fridge finally arrives but the whole side panel is damaged. Send it back and order Fridge number 4. Service from Brick, Maytag and Whirlpool, terrible customer relations. Misrepresented delivery dates, supply issues, and operational damages.Fridge finally installed. Ice maker operates intermittently for the next year. Service techs from TransGlobal offer a variety of suggestions including changing filter, water pressure issues. Finally ice maker stops entirely in Summer of 2013. Is replaced after a month of waiting for parts of which the wrong part was sent. Ice maker continued to operate intermittently. Sometimes just a small of ice or no ice for a day. Finally in May after another service call, ice maker stopped working for about 4 days. Tech comes out and miraculously, it starts working again. A month later stops again and hasnt worked since.Contacted TransGlobal off shore call centre? And arranged to have an assessment to see if we needed a new fridge. Request declined and Maytag (Whirlpool) sent a tech out after another week. Service tech recommended new freezer. Waited a week for parts and arranged for Service tech to replace ice maker. Wrong ice maker part (for the second time) in less than a year.The latest trick from our possessed fridge is recent alarms from the temperature control. To say we are disappointed in this product, the retail experience, the quality of the manufacturing, the shipping procedures, the poor engineering and design, doesnt come close to describing the shoddiness surrounding this appliance and the service weve received.In conclusion, we are still awaiting an ice maker and are contemplating buying another fridge. What it is fair to say, we will never ever buy another appliance with their the Whirlpool or Maytag attached to it. Nor will we ever again buy anything from the Brick, or depend upon TransGlobal for repair services. Are there other Manufacturers and retailers out there who understand the meaning of service and quality. I certainly hope so. Otherwise Im going to invest in a good icebox.

The last Maytag washer was great, the dryer not so much, but I was able to repair it. This Bravos is sorry. 4 years old and the tube goes bad is not what you would expect from Maytag. Consequences, no more Maytag or GE for that matter, that dont leave many brands to choose from.

I had the exact same experience as the Tampa person with my Maytag dishwasher (Model: MDBTT60AWW). It was not cleaning the dishes, even when I thoroughly rinsed them. Plus, it started leaking midway through the cycle. Since the warranty was expired, I purchased an extended warranty in July 2012 for $296 (yes, in hindsight, I should have just bought a new appliance, not Maytag). I had 3 visits from 2 different technicians, both telling me the dishwasher did not leak. One telling me I was using the wrong kind of detergent and thats why dishes werent getting cleaned. The other telling me that there were too much suds and that could cause it to leak. So, I should pour a tablespoon of cooking oil (yes, cooking oil) in the dishwasher when it starts leaking and that will cut down the suds. I dont think so!Then, I found out a couple of weeks ago that this model was under a recall since 2010, not related to the leak at all. Yet, Maytag still sold me the extended warranty (wheres the ethics of that?). I requested a pro-rated refund of the balance on the warranty - and wouldnt you know that with the technicians service calls, the amount of time used on the warranty (6 months) plus an admin fee - I have used $296.48 of the warranty amount. It is almost to the exact penny of what I originally paid, so I will not be receiving any refund. They are only giving me a debit card of $150 or $250 once I buy a new Maytag to replace the recalled model. I do not want to continue down this frustrating path known as Maytag appliances.

I have owned my Maytag washer for approximately five years. Ive always used the recommended detergent and religiously used the tabs to clean the machine when it was required. I have never abused the machine by overloading it, using too much detergent, etc. It is now coming up with an LF code. There is no one in this area who does repairs and if I do find someone Im sure theyll want some exorbitant amount to come all the way out to the boonies to give an estimate and the repairs Im sure will be hefty. I take very good care of all my appliances and expected this machine to last much longer.

My home has all Maytag appliances, all just over 2.5 years and I have had no issues with any of the other equipment excepting the fridge. The fridge itself works very well when it does, but some things are just wrong/flawed with the French door fridge.1. The Evaporator mechanism is flawed and keeps accumulating frost over the Thermistor sensor, which in turn shuts off the fan and the fridge itself stops cooling rendering all the produce bad within hours of purchase. The freezer and icemaker works fine during this time. The first time a tech came in during Warranty period and put come Aluminum foil over the thermostat and zip tied it and told us that the issue is resolved. Fast forward 18 months or so, same issue. This time they want to replace all parts since the last time it did not fix it. How convenient isnt it? So now I have to shell 500 plus bucks to solve what was not fixed the last time. Flawed design is all it is; do not purchase any of the French door fridge from Maytag/Whirlpool or be prepared to buy an extended warranty and a down fridge every 12-15 months at the minimum. In my case shell out 500 bucks every 15 months I guess.2. Sloppy icemaker: Ever heard of an icemaker that thinks and drops 4-5 cubes when requested and thinks again before giving another 4-5 cubes? We see it all the time at Soda fountains. This is what to expect off a Maytag ice maker. And lord knows if you have guests, they will run through the batch of ice by the very first meal and then the princess ice maker needs 12 hours to make another batch of ice.3. Noisy fridge: Ever heard a noisy fridge in a very quiet home? This Fridge excels at that. Just about the time it shuts off the compressor, boom it goes on again.

I would like others to know that Maytag does not stand behind this product at all. I am not sure about other products, but after talking to Maytags customer service team I would guess you would get the same runaround with other products. We have had our washers for about eight years now and have had many things go wrong with it. The one that gets me the most is the one that my appliance repair service does not cover and that is the main bearing. I have done some research to why this is and most of them do not cover this, because they should last for the life of the washer. Most washers last for more than ten years. However this washer has only lasted a few years on each bearing. I have now put in my third bearing into this washer. The last bearing only lasted two years. If I had to pay for labor on replacing this part I would have not replaced it. I had been given a quote for replacing it and it was over $350. Some places wanted more than $400 to do it. To me the washer is not worth this. Yes we paid like $900 for the washer, but it is not worth putting that much money into this washer. If you cannot replace this part on your own then just walk away from it. Buy a Speed Queen. I know Maytag has sent parts to other people free of charge, but I have not been so lucky. When you send others part to fix the same problem, to me that is admitting that there is a flaw in this washer. With that said my wife and I already filed a BBB complaint against Maytag and will be sending a letter to the Minnesota Attorney General. I have proof they have sent replacement parts to others and dont see why they cannot do the same for me. Maytag is own by Whirlpool, you think it would be cheaper and easier to make customers happy than just brushing them off. I would say that customer service in many of these large companies and even small companies is gone. I remember when you would call a company and make a complaint and they would go out of their way to try to make you happy. Now they come up with reasons why it is all the customers fault that their products are bad. Maytag is just another example of a greedy business that does not care about their customers. So please do your research before you buy this product and good luck to those who have that are stuck with the junk that Maytag sells customers.

BUYER BEWARE!!! We purchased a Maytag Dishwasher mdbh979sab1 on November 23, 2012. It is now July 31, 2014. One year and a half and the control panel is not working. Ive looked at estimates online of $450.00 for parts and labor. Customer service is no help at all, nothing they can do. She actually recommended KitchenAid for our next appliance. Maytag has become a terrible brand. We will never buy from them again. By the way, they also made our Jenn Air Oven, which turned itself on a number of times while we were away. 350 degrees. That was a total loss as well. We are filling up landfills with our Maytag/Whirlpool appliances and you will too.

Very poor quality. Vegetables freeze at the back of the fridge I have tried everything. The vegetable drawer constantly comes off its track and the freezer door slide jams and stops the door from closing. It leaves about 1/2 inch gap. Now the Whirlpool/Maytag company changed their corporate policy and wont allow an appliance store that to come out and fix the fridge I have to go back to the manufacturer. Their website wouldnt take my email address when I tried to sign up for an account and they wont answer the phone. What a hassle. Ill buy another brand next time but never GE or Whirlpool again!

I have always loved Maytag but this top load washer is a bust. I purchased this higher dollar energy efficient washing machine to hopefully get the value out of it for years to come. Model MVWC565F. 4.2 Cu Ft. I use good quality liquid laundry detergent. I launder adult clothing (including business casual wear), sheets, towels and pet blankets. Occasionally the 20+ something children do their laundry while home. I often have dry spots on my clothes where they never got actually wet. I switched to only using the deep water cycle; however, this does not immerse the load in water. The smaller my load the less likely to get clean. Ive adapted to only have large loads but I still do not feel my clothes are getting clean. I often have to run the load a second time to not only remove ordinary day-of-wearing smells (very noticeable in socks for example) but to get them all wet and free of soapy/linty-like spots left on the clothes from the washer (most notable on black leggings, dress pants, etc). I always do my towels and bedding separate from daily clothing, so this is not coming from having a mixed load. I have also noticed that the load takes much longer (up to 2 hours) for my washing cycle. How is this energy efficient? It uses less water but more electricity? I miss my old fully-immerse-in-water washing machine that washed in under an hour! Love the dry that I bought with this but not the washing machine!! I do not recommend this washing machine!!

I also purchased a Maytag dishwasher a few years ago. It has never worked that well. We had a repairman come out once to replace the control board but the problem soon returned. Interestingly, we found that if we wait long enough until the control panel is in the mood, the dishwasher works again and the control panel responds to button pushes, until the problem returns.I dont recall what model I purchased but it seems to be irrelevant. From reading the other customer complaints, its quite obvious that all Maytag dishwashers inherently have problems with their control panels and Maytag intends on doing nothing about it. I guess the extra repair costs that their customers have to pay for their defective products brings in some additional revenue to Maytag, so theres no real motivation for them to fix their ** products.

It is impossible to dry clothes in the dryer without the worst wrinkles you can imagine. I have 2 of them and they are both horrible machines!! The drum spins too fast which causes the clothes to get stuck against the tumbler fins. The centrifugal force holds them there and they just ride around without tumbling in the drum. When the cycle is finished the clothes have been dryer while jammed up against the fins and they are so wrinkled you have to wash them again. The ONLY way to get them through a drying cycle without a tremendous amount of wrinkles is to stop the machine every 5-8 minutes and fluff the clothes around inside the drum by hand. DO NOT BUY!!

I am at my wits end, as I try to get some satisfaction for the fact that this stoves cleaning system does not work! We purchased this stove at Home Depot in Hadley Massachusetts on February 2, 2014, and it was installed in a seasonal cottage that we were having renovated. When we arrived at our cottage in May, I was delighted with the stove. The cook top performed well and the oven size was great. During the summer, we tend to grill outside so the oven didn’t get much use, but it perform perfectly every time I used it. I always remove any debris that may have spilled immediately, and didn’t see any need to user the AQUA Clean feature until we were getting ready to leave in October. When I ran the cleaning system as recommended in the manual, there was a stain on the bottom of the oven. I then ran it eight (8) more times with the same result.I called the service number and they scheduled a service technician to come for a visit. He said that the stove was working the way it was designed to and unfortunately since it really didn’t get hot enough to do the job, the stain (and with more use, more stains) would remain. He also noted that should I try oven cleaning products, my warranty would be voided. This was not the answer I was hoping for, but since his visit was on the day before we were heading South for the winter there was not much I could do.Have called the service number several time since then, asking what could be done to rectify this problem with no positive responses. One did say that they could send the service tech again and went so far as to schedule an appointment for January, which she suggested I postpone with the technician until we return in May. The reasoning being is that since the warranty is only for a year, and the cottage won’t be opened until May, the fact that the original appointment was within the warranty period would cover the cost of the visit. When the technician called a few days later, the scheduler said that it made no since to go again, unless Maytag came out with a fix for the cleaning system. Since it’s not broken, but just does not work. I again spoke with a service rep and asked if anything could be done or if I could speak to a supervisor, she said that one would call.. That was weeks ago and still no call.We purchased this stove with the hope that it would last for many years, especially since it is only used for five months of the year. Ease of cleaning the oven is important. Home Depot no longer sells this model, and after some searching the internet I have found that I am not alone with this issue. Apparently it is quite common. We will not be able to access the cabin until May 2015, but would appreciate anything you can do to expedite a replacement of this stove, with one that actually self-cleans or a refund.

Bought the dishwasher (model MDB8969SDM0) at Lowes Burlington Canada beginning of September. After two months of use, the plastic pins and attachment to the drum, top rack broke and cracked in several places. Called Whirlpool Canada for repairs many times and got the run around, spent hours on the phone and still not resolved as of December 12, 2014. This model has a problem with the plastic and breaks continuously as seen by many reviews on the internet. The technician said that this is a problem with this newest model. I have now been waiting for over two weeks for the parts with no end in sight since they claim that the parts are back ordered. Called again today and was told that it would be another week to see if they can find the pieces. This is ridiculous, I paid over $ l,000 dollars for this model and it looks like now that I will not have it repaired by Christmas. Lowes refuses to help me because they have washed their hands since it broke after one month. I have been lied to many times by customer service at Whirlpool Canada. They claim that I am the first one to complain about this model yet the reviews on the internet are full with this issue. They say what you want to hear and do not seem to care at all. It is a disgrace, I feel totally cheated and robbed of my hard earned money. Maytag is no longer a good company for their appliances and service. I am starting to think that I am stuck with this machine and that they have literally robbed me of $ l,000. Shame on you Whirlpool and Maytag.

Excellent dishwasher but door kinda flimsy. Front panel scratches too easy. Top rack needs to be stronger and a bigger bottom rack. Other than that running wise dishwasher is excellent. Its hard to beat Maytag. I think they just build cheap stuff around good motors.

I have always been an advocate for Maytag Appliances. Never bought anything beside Maytag. Our old Maytag refrigerator broke. Would cost too much to fix. So, we decided to buy new. We had the old white, which I was perfectly fine in buying again, however, white was super expensive. So, the salesperson persuaded us to purchase stainless steel. We got a pkg for close to $4000 all in June of 2016. Needless to say, these items have been called for repair within the 1 year warranty over half a dozen times, and have had to replace pieces that have just broken. My worst experience is the stove. I really do not like it at all. I feel the product is misleading. We wanted a self cleaning oven. It is the newest brand out there for what I consider a joke. It is the AquaLift Technology that does not clean anything. My old Maytag self cleaning oven cleaned far better than this. The same spots are in the oven. It just is worthless. I have addressed my frustration with Maytag where I was told that the oven is for the light user. Well, then you need to educate the people who sell your stuff, because I have a family I cook a lot. If this product was made for an apartment single person who does not cook then we should have been informed. Your product states Self Cleaning. Its not self cleaning!!! My frustration went up to the main office of Maytag where their resolution was to give me a discount on a new stove.What do I do with the one I have, and I was told I could sell it!!!! Really Maytag wow from a consumer that has always been a valued customer this is the level of service I get. I ended up purchasing an extended warranty on all Maytag products, because of my fear of something just breaking again. My advice to all is either buy a no named brand or buy something cheaper. Please folks if you have a family do not purchase these products. Its for people that just need a pretty display of appliances!!!

We purchased a top of the line, state of the art Maytag washer and dryer Neptune. The fill valve failed twice, flooding the first floor and the big storage room below. Thank God we were here! Now the thing halts mid-cycle and wont continue. The repairmen both said the design is messed up and they hate to work on the Neptunes.

I do not know how long we have had the Maytag but, it has been a long time and has run without any problems. Still looks good and does the job! The features of the Maytag are: pots & pans, temperature sense, sani heat, light wash, regular wash, pots & pans prewash, quick wash, rinse & hold, delay start and heat, fan dry, heat or air. This dishwasher has always been plenty big enough for our family of four including guests. This Maytag had a choice of black or white front so, it fits in. My next dishwasher will probably be a Maytag!

It went bad, then I called a technician who replaced the compressor. After a few months, it broke down again after I had bought new parts for it. I was very dissatisfied with how the refrigerator was built. I spent lots of money on it, and it wasnt worth it.

This washer (Model# MVWB765FW1) will not wash your clothes. Its not designed to give enough water for washing. That means some clothes will still be dry after agitator cycle; seriously. Thank you Maytag for going green! The repairman will tell you the machine is working according to design. That is true but the machine is a fraud as a clothes washing machine. The weight of the clothes in the tub tells the computer how much water to apply; good luck with that. We learned that if we add a bucket and a half of water, the clothes will come clean. Do you want to do that? Maytag used to be a good name.

Just like so many others, our Maytag 300 Quiet Series, just 2 years old, has a malfunctioning control panel. Repairman told us this has been an ongoing problem with Maytag dishwashers. Steam/water gets into the control panel.For a while it worked on and off and now it is dead. I am saving up to do the repair, but in the meantime the dishwasher sits idle.

Approx four months ago we got new stainless steel Maytag fridge, stove and dishwasher. Terrible, terrible, terrible. The dishwasher rack was broken, and the parts are plastic and hardly any room on the racks. The fridge had the wrong hinges and doors on them. We have been waiting for four months to have them replaced. Today we checked with Maytag and still not coming. The fridge makes a very loud humming noise it almost shakes the floor. This was some sort of compressor problem. Now the fridge is having problems with the freezer. It is freezing up with frost everywhere. The stove is terrible. I waited an extra month to get a convection oven which I have had before and this one is terrible. The double oven is a great feature if they work. They take forever to heat and if you do anything with the food you have reset the temperature? The top is the worst for cooking as the only one that works fast is the boost but then it slows down and you have a hard time cooking the food. The black top is very very hard to clean. I have owned a Maytag washer and dryer for the last 34 years. They have been excellent. Since Whirlpool took over Maytag they seem to have run the name into the ground and all the good service and products they had built up are now ruined. I told my neighbor a few years ago to buy a Maytag washer and dryer and they did. They have had nothing but trouble and are now having to buy new ones but not Maytag. It is a shame that with all the technology that Maytag has built up over the years is now gone. If you look at all the terrible reviews I dont think Whirlpool will be in business much longer with products and service like this. I still have a fifties fridge for pop and beer and it is the best fridge ever with no problems and my last fridge in my garage, that I replaced with this Maytag is still better than this new fridge. The service man that came to fix the fridge said we had to build in the fridge to keep the noise down. How come they never had problems with Maytag products years ago. I feel its all about the almighty dollar. They only last a few years and you have to buy expensive warranty. If you made them properly you would not need warranty and they would last for years like before. If anyone knows if there is a class action suit against these companies let me know since all of us should not be ripped off and costing us time and money.

I have owned my Bravos XL for over a year. Loads of wash have come out with rust marks. These marks do not show up on all items, only one article of clothing/sheet/towel seems to pick up the rust marks (usually a couple of dots near each other surrounded by a circle). They are always the same. They have shown up on sheets which were washed in a white cycle and on other clothes of various colors.I have ruined numerous new clothes and must accept the fact that these random but frequent rust-colored dots are part of my life. I expected more. Im getting ready to purchase a W/D for our home up North and believe its necessary to return to a basic model, probably a GE. Maytag seems to have jumped the gun on this one… putting new product out there, aware these unresolved issues remain.

Our experience with our Maytag refrigerator has been anything but good! It has the model # and serial # of the ones that have been recalled, only we have just found out about this. We bought this new at Sears. Soon after, it started having troubles with the freezer, would freeze up and the whole thing would stop working. Over the years, we have had repair after repair, money after money. Just for the record, my husband and I about every two weeks spend about one hour defrosting this monster! It looks nice on the outside.

I bought this after having a Frigidaire for 40 years and was immediately disappointed upon installation. This OVEN, not a range, was smaller inside and a lot of new pans would not fit! I have replaced the burners and the bulb wiring several times. Would not buy another one!

The washer is not cleaning the laundry. Its a HE my butt. Its been looked at and fixed numerous times. It sits too long and it doesnt really agitate the laundry at all. Laundry is in the exact position when you loaded it when its done. Its the worst washer ever! I can clean the laundry better in the sink!

I bought this range Nov 2019, beautiful range that’s it. Stove top scratches very easily and hard to clean. Oven racks rust, got them replaced on the guaranty they still rust. Oven dirty never gets clean, If I could afford it I would on the curbside. I wouldn’t even give it away. 3 oven in 48 years of marriage, worst oven ever.... Sure would like a full refund, I mean 1500. What a ripoff.

My washer is less than 3 years old when I noticed the bleach dispenser has filled with water. I soaked the water out with a towel only to have it fill again the next time I washed. This in addition to the feeling I have that too much soap is left in clothes and spot removal is pretty consistently negligible.

I, too, am absolutely done with ANYthing Maytag. We purchased our Maytag microwave model MMV4205DS-1 in January of 2016. Within the first year we experienced occasional open/close door issues due to the faulty door latch switches. Now it happens virtually all of the time. The ten year warranty is a joke; it is just a come-on designed to deliver a false sense of security that Maytag will indeed stand behind their worthless products when in fact they wont. I am so disgusted with them.

The microwave does everything I need and want it to do perfectly. It has never needed to be repaired or replaced in five years. We bought it on sale from Best Buy and consider it one of the best bargains we have ever made. Easy to operate, easy to clean, sleek and, for an appliance, quite personable. I find it refreshing to say something nice about an inanimate object.

I bought a Maytag Bravo Series 300 washer and dryer for $2,000. The dryer is fine, so far, but the washer is dead. I have not received any answers from Maytag and the product is already outside of its warranty. I only had it for two years.

The functionality of this machine is so awful. I had the dealer replace it only to find that the awful noises that the machine makes, the fact that the clothes don’t get covered by the water and the clothes are so knotted after the spin cycle you have to untie them is normal for this awful appliance. In the sensing stage the machine groans like a laboring motor around 30 times, then stops with a jolt. My machine is next to the bedrooms and the noise wakes people up. Even in the “deep water” setting, the clothes are not covered by the water. The wash cycle is short and noisy and the spin cycle goes on forever. In the end I have to untie the legs of pants. Whoever designed this machine should be ashamed of herself or himself. Shame on Maytag.

I had a GE washer and dryer when I first moved to my new home - lasted 15 years. Then... bought a set of Maytag and they have both been the biggest pain in the world. Spent 3000 and Im ready to toss them after 3 years. Dont buy Maytag!!!

We bought a Maytag refrigerator two years ago with the front french doors and bottom pull out drawer. We chose Maytag because we thought it was a name we could trust, a good quality merchandise. However, in the last two months, we started having problems when the fridge wouldnt stay cold, the freezer worked fine. We removed everything from the freezer and my husband found the freezer needed defrosting as the back of the unit was a solid sheet of ice. It took hours to defrost and we thought that we had the problem taken care of.. and that we wouldnt have to worry about this happening again. However, we have now had to do this three times in the last two months!! I love the style of this fridge..but am getting SO ANNOYED with having to rip everything out of the freezer and spending HOURS to defrost it! I have NEVER had this problem with any other fridge!! Im ready to replace it, but weve only had it for two years, and I shouldnt have to be spending a fortune on ANOTHER fridge after TWO years!!

I have a Maytag dishwasher model mdb6759aws3. The control touch pad broke after 1.5 years of light use. It costs $475 to fix (includes labor). Completely unacceptable service provided by Maytag over the phone. The only concession offered was a 25% discount if I bought the replacement part (control touch pad) from them. After some internet research, I learned Maytag marks up their parts prices over 25% so they are really not giving you a discount at all.I filed a complaint with Maytag but they were unable to provide me with any evidence of doing such except for an 11-digit code. Due to a major defect, Maytag should have sent me the replacement part for free. I told Maytag I thought this was fair and that I would pay for the labor. I will never buy another Maytag appliance again! They are junk and the company does not practice common sense customer service.

Maytag dishwasher model MDB7759SAB, 1 year old and control panel will not work at all. Maytag site does not recognize model #, got part numbers off parts and cant find the parts. Looking for control panel, cant find black one and others are back ordered for weeks. After reading other peoples problems, it seems Maytag would correct the issue.

I do not like this Maytag Centennial Washer at all, I have had it for a year and a half and it just does not perform good at all. Most of the time the clothes still come out with dirt on them but what I am most mad about is the fact that it keeps leaving bleach spots on my clothes, several washes after I use the bleach. I will definitely not recommend this washer to anyone.

I have read all the complaints. I have similar issues with Maytag Bravos. I’m frustrated that modern tech products stink to high heaven, especially when we refer to clean clothes not being cleaned well. The specific issues I keep getting are the following: the LF codes appear and the cold water does not fill so that it wont rinse or drain. I have replaced the defective washers and that helped for one load. I refuse to fix it. Why throw good money out for the same bad product? I’m looking for a no bells and whistles washer or dryer that works. I have issues with the dryer, too. No more Maytag products in the future. Question: Who truly makes a good reliable product nowadays?

Very disappointed with Maytag Bravos XL, four year old unit with bearings going out. Quoted $400 + for repair. With two in the house, wash demands are normal. Quality is questionable to have bearings & seal going out in four years. Also you cannot buy the bolt which holds the Washer Motor Rotor Cover on without buying the whole $130 assembly. Daughter has Whirlpool brand with same problem. Seems to me this is a problem Maytag/Whirlpool should address. My old unit (that I wish I still had), worked for 25 years. Would not recommend these machines.

I bought this Maytag French door model MFF2258VEW2 in 2010. Within the first year, it was freezing my vegetables. They sent someone out to fix it. Thank goodness it was under warranty. The man laid the bill down and it was over $800 to fix it. Six months later, it froze up. I called and they said they would send someone out, but I would have to pay for it. Im on disability and cant pay that kind of money. I got someone to come out and fix it. Well, guess what? It has started freezing my vegetables again. This is the third time this thing has gone bad. What do these people think they are doing putting things out like this? I had a Maytag for 30 years and never had any problem with it. So I saved and saved to get me a new one but I will never buy another Maytag. The company should have to replace all the refrigerators that are like this one.

This is a continuing aggravation! On July 27, I discovered the dishwasher (MDB7600AWW) tub had developed a crack in the bottom right rear and had warped my countertop and the floor under it was full of water! I called the appliance store where it was purchased and was told to call Maytag. I have a 20-year warranty on the tub with free replacement of the unit if it fails. I called Maytag and was told we needed a service call to verify. I scheduled it for July 30, and 3 minutes and $75 later, yup, tub is cracked. Its a known problem, and the dealer has already replaced some for customers. I called Maytag to get the ball rolling for replacement. I spoke with Jennifer and was told shed get back to me.Meanwhile, we went to several stores, checking out other Maytag models. So, Id have some idea of what was available as a replacement. I called Jennifer on July 31 with a suggested model Id find as a suitable replacement. She said shed check and get back to me. On August 13, I called Jennifer for some answers, got the voicemail, and left a message. On August 14, I went online to chat. Finally, I was told Id have a replacement in 10-12 days. Id be contacted to schedule installation. On August 16, I called a local dealer again. He cant understand the problem. Hed replaced two others in a few days. He made some calls for us and gave us the name and phone for the company replacing the dishwasher as well as the work order. Installation was tentative for August 23. (Hed been cut out completely!)I called Optimus Solutions, and theyre awaiting shipment. Tentative installation was on August 23. On August 22, theres still no word. I called Maytag customer service. Sorry, it was shipped to the wrong address, so it was shipped back! Its now in transit and supposed to be delivered to Optimus Solutions today but not being scheduled for installation until August 31!This has become one nightmare after another with everyone pointing the finger at the next guy. Phone calls get only the same runaround. No, speaking to a supervisor wont help - theyll tell me the same thing. Isnt that convenient! Meanwhile, Im still washing dishes by hand and having psoriasis on my hands, which are like two pieces of raw meat right now. It is beyond aggravation; its bordering on torture! (No, I cant wear gloves. They make my hands sweat and even more sore!) Besides, I shouldnt be washing dishes by hand. I paid for a dishwasher that failed through no fault of my own, and now, Im being punished for purchasing it. I can guarantee that if I had no warranty and had to replace this dishwasher, it would have been replaced immediately!Never again. I purchased all Maytag products for my new home. As they fail, I can guarantee I will not be replacing them with Maytag or Whirlpool, which now owns Maytag. I will be telling everyone who will listen to stay away from Whirlpool and Maytag, because their customer service sucks big time.

I have owned a Maytag gas dryer for 10 years now. I have had to replace the idler and belt 4 times now. This dryer appears to be built as cheaply as humanly possible just to get it past its almost non existent warranty. The replacement parts are even worse. The idler has a bronze bearing in it as a wear item. Really??? Why was this never even considered as a part that could be lubricated at least occasionally?Granted, lots of people do not have any mechanical ability at all and just pay through the nose for a repairman to come to their place for any repair then pay dearly for the service but, I DO have mechanical ability so I do all the work myself. That is why I know firsthand about the terrible manufacturing results and the very cheaply built replacement parts available at outrageous prices.

I purchased the Maytag refrigerator MFF2055DRM on 7/7/16 new. It was suppose to be stainless steel; but now I am seeing rust spots at the top and bottom of the French doors. I clean my refrigeration weekly and find it odd that now it is rusting. Also, I am able to place magnets on the doors - which should not be for stainless steel. In addition, I spend over $100 a year replacing the mandatory filters. I must also place the setting to high to maintain my milk and juices. I must also have to place them in the very back of the refrigeration. I am a single senior and my refrigeration is not overloaded with food; nor am I constantly in and out of the refridge. Not very happy.

Loading is easy, operation is extremely quiet, dishes are very clean even on normal auto wash cycle. White, integrated depress buttons, full size, removable utensil baskets, upper and lower racks, top rack is manually adjustable, stainless steel tub. White front which is what we want not the ugly old metal stainless steel, usage buttons are on the upward facing edge of the door, pull down handle is nice size and very sturdy. Model is MDB8959SBW3. Even on normal auto wash cycle dishes are clean without much pre-rinsing. Purchased 10/14 from local dealer and professionally installed. So far we love it.

In my owners manual, the description to replace the oven light shows a simple process of removing a glass bulb cover within the oven itself and then unscrewing the ordinary looking light bulb. However, Maytag made a design change and now uses a complete unit that combines the bulb, the glass cover and the bulb holder. This requires you to pull the stove out from the wall, open up the back of the oven, bend some retaining tabs around the light unit and then remove the whole unit.The killer is, Maytag has made this disgusting, usurious design change in order to force you to pay over $50 US plus taxes and shipping for the replacement unit, instead of $6 CDN ($4.50 US) for a light bulb that you can buy anywhere and can easily change yourself in a couple of minutes within the oven itself. But now you will probably have to call in a repair guy to make this replacement for you. When manufacturers start doing things like that, its time to stop buying their products. I will certainly never use Maytag again, and Ill make sure any other oven manufacturer Ill consider is not doing anything similar.

Bought this Maytag washer from Sears and the salesman told us it was the best washer on the market. Well the Maytag washer is a dud. It leave residue on clothes, clothes come out very wrinkle. This washer does not even have a filter. I would not recommend this washer to anyone. We are very dissatisfied. We dont blame Sears, we blame Maytag for even thinking about putting this washer on the market - Maytag model mav7757aww

Overall- I think washers aren’t made to last like they once were. Growing up- we had the same washing machine while living at home. It seems now- they only last 10 years if you are lucky. They should make more longer lasting machines.

I really like my Maytag dishwasher. It has been very good. I have had it for at least 10 years and it is still working fine. It is worth every penny. If this one stop working I would buy another Maytag dishwasher.

French door refrigerator w/ freezer in bottom 2 years old. Purchased this model MFI2665XEM7 December 2012. June 2014 had repairs to freezer. Freezer froze up and bulb stopped working. Maytag covered repairs. September 2014 the ice maker stopped working and having it replaced as we speak. Total cost today for ice maker replacement $216.18. Am I POd, hell yes!!!!!!!!!!!!

Actually, I have had my Maytag washer and dryer for 20 years so they are not new but I am thankful for this set because of the workload it does for me. I sometimes wash heavy loads (blankets, bedspreads, small area rugs), and this pair performs superbly. My son wanted to buy me a new set for Christmas last year but I definitely said no. I truly am happy that I bought Maytag and I truly believe that the Maytag repairman is a bit lonely.

We bought a new home with all new Maytag appliances. Our Maytag dishwasher has had 3 new handles, 1 inside tub and now needs a new touch panel. Our Maytag oven/stove has needed three ignitors and the oven door has never been right! The microwave is the only appliance that we have not had a service call. Appliances are expensive along with parts and labor for service calls. I will not be purchasing any more Maytag appliances. The standard comment by repairman: They dont make them like they used to. How sad is that!!

I’m 41 years old and finally had my first new washing machine. Four days later, while my 11 year old had the stomach flu, it died. Not impressed. Apparently the delivery guys left a note on our file saying there was a defect on our washer and that we needed to contact Maytag. This was news to us when we called The Brick today. I hope they didn’t knowingly sell us a defective washer. Alas, we have to wait until Monday with pukey sheets in the washer.

I just purchased a Maytag Washer and Dryer. I am very pleased with the cleaning ability of this washer. It has set pre-timed washing and drying times. I would like to have availability of setting the times for a load to run. Same with the dryer. The book says you can do this but I have not figured out how. I have been very pleased with their abilities to do what they are supposed to do. Cleaning and Drying.

Purchased Maytag Dishwasher Model MDB7749SBW3 in April 2014 along with other Maytag appliances to go into our home in the Georgia Mountains. Purchased Maytag for 2 reasons: 1. American made 2. Reputation. Bottom line, after just 2 years the dishwasher has failed. I prewash by hand everything that goes in. First the normal cycle stopped working. Then lights on front panel would randomly turn on and dishwasher would turn on by itself, and run for hours. I suspect this could be a fire hazard. I have tried front panel resets, cycling power, etc. Nothing works... It is really sad that American products are third world. I will replace the board myself in hopes of getting another couple of years out of it. No more Maytag for me. Rest assured every time I see someone in Home Depot or Lowes, looking at Maytag appliances, I will go out of my way to warn them.

We received our new Maytag washer MHW8200FC on Saturday 11/18/17. We washed 2 loads on Saturday and on Sunday it didnt start. Not only did it not start but it was locked with clothes in it. We finally got it to open but it wouldnt start to wash. We had the distributor, Warners Stellian, schedule a service tech. He came out on 11/21/17 and determined the board was bad and that he would order one and be back on 11/29/17. A week without a washer doesnt work for a family of 5. This isnt like a lawn mower I use once a week, we use it daily. Whatever happened to quality control? A brand new expensive product breaks in 2 days? Maytag says its Made in the USA, which Im all for... Only if it works. USA or China, broken is broken so I dont care where its made. Whether its planned obsolescence or just a plain faulty product, Maytag is now another brand that I will avoid buying in the future.

I bought a Maytag dishwasher (MDB7749SBW1) about 4 years ago. Ive had to replace the wiring on the control panel each year. This is clearly a design defect, and Maytag will not take any responsibility for it. Ive called each year, and am told each time that theyve never received a complaint about this issue. This year Im replacing the dishwasher. Ill never buy a Maytag product again.

I purchased a new electric oven/stove, dishwasher and over the stove microwave. My dishwasher didn’t work from installation and it took Maytag over a month and half to repair. My oven door hasn’t worked properly since purchased and finally broke and I have been without an oven for two weeks waiting on repair. The customer service does not listen to you and seem to be completely unconcerned about your problem. I was told the item broken was a common stocked item and the repair would be quick but that was not true. The repairman told me they would have my parts in a week and would install them on a Monday. They have now scheduled my repair for Thursday. Over two weeks with no working oven. I will never purchase a Maytag appliance of any kind due to the terrible customer service.

I bought the washer/dryer a few years ago. I did not realize how they do not own up to their reputation. Rather expensive. My clothes are always twisted together when finished washing. Parts of them feel dry. My dryer seems to be ok. Comforters are a pain as the load always gets unbalanced. Lately it wont finish a load. I get LD all the time. Have to unplug the washer and wait for it to cut off before cutting it back on. Then I cannot just rinse or spin. It fills back up with water and I get the same LD again. If I had seen all these reviews before I bought this set I WOULD NOT have bought them in the first place.

We have a Maytag Neptune washer and dryer. The seal is full of mold. We replaced the seal a few years ago and I wipe it and try to clean it every load, but it is useless. I saw there was a class action suit and I was never notified of this. I would have participated. I want it fixed, replacing the seal does not work.

Maytag calls peeling paint a cosmetic issue. With a convection oven it could be a toxicity issue. Waiting for an answer to my question as the fan blows the peeling paint onto anything that is not covered. Dont put foil on the bottom as this compromises the paint due to design. Truly sorry to have purchased Maytag as this line is not the Maytag we grew up with! Old school ovens and products had the quality or workmanship to last.

Like many people here, I have a Maytag Dishwasher Model # MDB7749SBW3 Serial # F40107007. We have had this dishwasher for about 12 months to 18 months. The first indication that there was a problem was some of the lights were acting strange. Then the dishwasher starting going nuts. I removed power from the unit thinking that maybe the controller became confused. The problem persisted. I would hit buttons and either nothing would happen or something completely different would happen.I take the dishwasher door apart and remove the touch pad. I notice some discoloration on the ribbon cable. I remove the glued on front panel to look at the electronics behind it (see pictures) and I see some discoloration there as well. So using my multimeter, I find that there is a direct short between pins 4 and 5. I vigorously flex the cable at the point of discoloration and the short goes away. So at this point, I doubt that I can get just the flexible circuit strip so Im going to have to pop for a new touch pad assembly. I didnt go further in the measurements as there was no point since I already detected one failure. Furthermore, I inspected the computer control unit and I did not see any obvious signs of corrosion or discoloration anywhere on the processor board. So it appears that there is no problem with it.Conclusion: Many people are at a disadvantage when it comes to electronic devices. In my professional opinion, this is clearly a failure of the insulating material of the ribbon cable due to environmental contamination. Visual inspection shows that corrosion of the conductors is clearly evident. About Me: I have been an electronics technician on and off for over 20 years now. I have a 2-year college degree in electronics technology and I am currently in school to become an electrical engineer. In my house, when something breaks, I fix it.

Do not recommend any top loader. The washer dont wash at all. My clothes just sits there floating in the water on deep fill. I have some white with metallic like marks. Ive have soap left in my clothes. I watched one load of clothes. It had a neon shirt, the shirt stayed on top with the bubbles, it just floated along around in circles. The service was crap too. I called about the metallic markings. They said it was normal and should go away after 15 - 20 loads. I cant afford to replace my clothes.

I purchased my Maytag washer and dryer set from the Maytag store in Glendale, AZ in September 2005. I even bought the stands for them. With my purchase, I got the extended warranty for four more years. I didnt realize that I would really need it. I have had so many issues with the washer and dryer I cant even count - from the control panel not working, to the noise and the vibration when washing, or maybe in the smell of moldy cheese. I also have issues with the constant chimes of D5 code that keeps coming up on the display screen. After 2009, I finally gave up on calling the Maytag customer service folks to have someone come and service the washer because it was out of warranty. I just decided to live with all those issues.As far as my dryer goes, the rollers went bad and that was replaced. The burnt smell isnt so bad as long as you use a wire hanger with a sock on the end of it and clean the inside of the vent. Then try to vacuum it, take the sock, get it wet, and clean the inside of the vent again. This was the most expensive piece of junk I have ever purchased in my life (almost $3,000.00 with the stands and warranty).What really gets me upset is I had the Maytag people servicing my washer and dryer up until 2009 and no one told me about a recall of my washer and dryer. The only reason I found out about it was searching for the specs as the washer finally died and I am replacing it. Trust me. I will not be purchasing a Maytag. I know that Whirlpool purchased Maytag so I am not even going to consider Whirlpool either. Since Whirlpool purchased Maytag, Whirlpool should have contacted all Maytag consumers, (which they didnt), put ads in newspapers (which I did not see) or put an ad on TV. None of these appeared to have happened.By the way, when I bought my Maytag appliances, I was supposed to get a $200 rebate for buying the stands that never came. It must have gotten lost in the mail - as well as the Tide coupons for three years. You, guys, remember that too. I will never ever purchase a Maytag appliance or Whirlpool, since they own Maytag now.

We bought our Maytag Neptune washer in 2005. We chose Maytag because of their reputation, their headquarters in Michigan, and because looking at the machines in the store, they seemed to be well built. Were we ever wrong! You would think paying $1000 for a machine would get you a product that lasts longer than 8 years! Our other washer (a Whirlpool) lasted 20 years and was still working. Im now consistently getting a 3e error code. In searching online, I found that this is a pretty universal problem and thought maybe Maytag had a recall on it. What a waste of valuable time. I did find out the machine was actually a Samsung. This seems like fraud. If I wanted a Samsung, thats what I would have purchased! Contacting Maytag Customer Service was like Land of the Stupid. After getting the runaround and being sent to a phone number and website that only covered Samsung I called Maytag again. I was put in contact with another person who could supposedly help me with the recall. Even though I told him what the problem was, he gave me the robot response about sending the GFCI plugin and told me, That should make your washer safe to operate. Seriously??? I replied, This wont fix the problem because THE WASHER DOESNT WORK and we got the recall part long ago. He then wanted to schedule a repair appointment. Not doing that, considering how stupid the Maytag reps I had talked to so far had been. Putting the hubby on the case, luckily hes pretty handy. On the upside, it was fun responding to the Maytag customer service survey that night, LOL. All of our other appliances are Maytag and they have all been great, but this washer is an unreliable piece of junk.

Should have researched before purchasing our Maytag Bravos MCT washer! We purchased it at Home Depot and it was delivered and installed by a certified technician. From day one it has been so loud and obnoxious with the way it “knocks” and “clicks” when it runs through a cycle. When it spins the whole machine shakes viciously, despite being balanced properly at installation.We have owned this washer just short of two years and for the last 8 months we have had to keep unplugging it to reset it so that it will even run through one cycle. The most recent two months have been extremely frustrating, due to the fact that not even troubleshooting can aid in “fixing” the fact that this piece of crap washer will not complete a wash cycle! It either stays in sensing mode & doesn’t add water, or it adds water but doesn’t do anything but sit still for about 15 minutes and then drains all the water back out and stays stuck on “wash”. We are researching online and have found many similar complaints with the same negative experiences. Our next step will be to call a repair person! What a crock!!! Maytag gets a big “thumbs down” from us!!!!

We purchased Maytag Dishwasher MDB5601AWW/46171101NP when we built our new home. In the last several months, water was leaking out onto the floor. We called Maytag and they told us there was a recall on the heater element and that they would send the part out. We made sure they knew the reason for our call--TO REPLACE THE GASKETS!. Maytag contacted a local authorized repair person. When they called to set up appointment, my husband reminded him about the gaskets. The guy showed up without gaskets, saying Maytag didnt put it on the order! We called Maytag to set up another service call. The guy showed up again today without the gaskets. We were told they had to be ordered and that he would have to come out again! Three service calls for one issue! Aside from this, the circuit board has never worked right. We push the correct buttons, but never know what kind of cycle we will get. We learned to live with it. Our bottom racks are melted as well as the sides of the dishwasher. Now that we know about the heater element being defective, this may be the cause of the bad gaskets and melted racks. It will cost almost $300 just to replace gaskets, and yes, we have to pay a service call for it when it could have been done in the first place. We called Maytag to complain and were told that replacing the gaskets always takes two service calls--one for diagnosis and the second to put in part. They said they dont take the customers word for it when we tell them whats wrong!

I bought a new Maytag stove and it is less than two years old and the oven has already quit working. It only has a one year warranty and will cost about $200 to fix. I am very dissatisfied with what I thought was a good product.

Please do not buy a Maytag washer top loader. It does not get enough water and it does not clean your clothes. It is the noisiest cheapest made machine out there. If you have kids you really need to bypass this one. I have had this for 10 months and its only me. Please especially if you have children stay away from it. Im the most unhappiest camper Maytag ever had.

I’m so disappointed in this refrigerator! It does not keep a steady temperature. It’s only 3 years old and will not buy another Maytag. I do like the freezer on the bottom but it also does not keep a steady temperature.

We had a repairman come out and take a torn pillowcase out that was jamming. It worked for a couple of weeks, now refuses to start. We have decided to rid ourselves of the Bravos 300 washing machine and not deal with Maytag any more. I would not advise anyone to buy a washer of this type, as it never really got the clothes clean to begin with.

We had perfectly working 20 year old top loading white Whirlpools w/ an agitator, when we remodeled our home and wanted new pretty grey appliances and decided to donate our machines to the church. I chose Maytag top loading due to their former reputation we experienced with dishwashers, etc. It had an agitator, deep fill option, extra rinse, etc. The sales person at Home Depot stated, the agitator is because people like you still want the agitator, and the deep fill will give you the water you have been used to. Not so at all!!Clothes get wound up together, even with filling the wash tub in bundles, there is almost NO water to thoroughly clean & the rinse cycle is a joke. Clothes do NOT come out clean. Im 58 yrs. old and have been doing laundry since I was 13 so I know what I am doing. Its just my husband and I now, and he is so upset that his clothes are pilling probably from rubbing together, even though I occasionally use laundry bags. I seriously wish I would have saved my money and kept the 2 perfectly working whirlpool units I had. This has been such a disappointment. I sincerely would not buy these.P.S. Weve had service out at least 5 times in the last year, and all they do is test the washer and tell us its working as intended... The last thing that is going to happen is we are going to get refunded for a different set, even though we were educated over and over what it would do by Home Depot associates. We are heartbroken. Maytag is going to lose their former reputation on these washers a dryers :( There is simply not enough water to clean or rinse things!

We bought a heavy duty washer 1 year ago and paid a decent amount of money for it. Had it delivered and installed mid February of 2020. Worked fine until Dec when the lid cracked (which is common said the Maytag repair man), but since it wouldnt lock, we couldnt use the washer. 1 week we were told and it would be in - a month later and over a hundred dollars spent at the laundromat, the part came in. Used the washer for 1 round of laundry - 3 days later all these error codes started and our washer wouldnt work again. 2 weeks this time for the parts and another $100 at the laundromat- a month today and Im told they are on backorder.Called the place we bought it and they said to call Maytag. Call Maytag and they said that they will try to expedite the parts and could offer me a whole $75 for the inconvenience. They will not replace the washer or give me a loaner until the parts are in. 2 months w/o a washer on a 1 person income for a family of 4 and they cant do a single thing to help. If a 10 month old washer needs 3 new parts one of them being a new control panel - within the first year - this is a lemon and should be replaced. I was told they are big on customer service, but obviously Im just a little fish in the ocean and they dont care about me.

I purchased the Top Loading Maytag Washer and have had nothing but an awful experience with this washer. The dark clothes come out with soap on them. I then need to take a wet towel to wipe out the soap stains. I have had a repairman in 2 times so far and there is nothing he can do to fix it. Maytag said I must wash all the towels with towels, all jeans with jeans, roll clothes into a loose ball before putting in machine, use the extra rinse cycle and the longest wash cycle and do not load clothes more than 5-6 inches high in the tub plus 7 other things I must do to get a clean load and none of those things have worked yet. If the salesperson would have told me all this, I never would have purchased a Maytag and nor should you!

I just purchased this Maytag Commercial Technology Washer and Dryer on August 31st, 2018 and We hooked it up today Sept 4th 2018. I put a small load of towels in this machine and it said it would take an hour and thirty seven minutes to wash. I added my detergent and pressed all of the necessary buttons and started the load. the machine started spinning and testing and adjusting. I waited to hear the water start to come into the washer but nothing. I then checked my water lines thinking they are not on but they were. Through the smokey glass on the washing machine, I could see water dripping as if it is hooked up to a slow drip IV Machine.I am taking this thing back ASAP!!! First thing in the morning on Sept 5th 2018 I do not need to call Maytag Customer Service because they know it is a piece of junk, so I do not need to waste a moment with this crap on my property. I see Maytag does not believe in a QUALITY ASSURANCE DEPARTMENT because that department would put a stamp of approval on this Junk for distribution.No Washing machine should take more than 30 minutes (40 mins max) to wash no clothes. I will have to invest in an old school scrub board and rocks, then I can understand an hour and thirty minutes worth of wash time. I have set the timer on my phone when I started this load and My towels have been in the washer for an hour so far and I can still hear the slow IV DRIP OF WATER going. I just checked the machine and the digital reading is saying it has an hour and thirty three minutes to go. there is no water in the tub of this washing machine. The towels are wet from the IV drip and the machine is now pretending to agitate the dirty towels but it is only going in one direction. It is truly a sad state of affairs, your hard earned money gets you nothing but junk and a runaround.

I purchased this high-end dishwasher 7 years ago and 3 years of fairly light use, the control panel on the top would operate sporadically or not at all. Called the dealer who sent out the repairman that installed it and had to replace the control panel to the tune of $300 once the labor was included (took 2 visits as he had to order the part, so 2 trip charges). Now 3 & 1/2 years later, it is doing it again!! A call to Maytag and then a transfer to Whirlpool customer service got me nowhere. They said there were no recalls or documentation for problems with the dishwasher. Really??? I see lots of complaints on this problem with very similar Maytag dishwasher models. They would not send me a new part at no charge as a result but offered to set up a service appointment for me so I can spend another $300 (probably higher now after 3 years) and would register my complaint. Thanks for nothing!Doing that would turn my originally $900 dishwasher into a $1500 one with the result that it will probably fail again in 3 years. Absolutely ridiculous customer service. I saw a YouTube video on taking it apart and applying silicone around the ribbon connections as others have done in the hopes I can get it working again for a while as I dont have the $$$ needed to replace it again on a retired fixed income. :(