I will never buy another Maytag Product in my life again. The Bravo is the worst of the worst washing machines ever. They claim to save on water but the electric it uses is terrible. You have to be a magician to untangle the clothes. Anyone who had anything to do with the workings of this machine should be fired.

A refrigerator we have had for just two years has been leaking water from the freezer and damaged our hardwood floor. We thought it was someone dropping ice or leaving the freezer drawer open but no, there is an admitted problem with the mechanism. No coverage from Maytag for the cost of fixing THEIR MISTAKE. The company doesnt seem to care. Got the run around from their management.

I purchased the Maytag Bravos 400 series top load washer about 4 years ago. Paid over $1000 for it, on sale. Its bearings started grinding within four years and the seal is gone which has resulted in water leaking out through the bottom of the machine. VERY expensive to repair and ultimately not worth it. Pretty disappointed that Maytag products reliable for such a short period of time and must then be kicked to the curb. NOT a quality product.

When I bought Maytag Neptune top-load washer, it lasted three months. I had to have the rockers replaced. Three months later, the lock switches went bad. Six months later, the main circuit board went out. Thank God it was under warranty. Ive had this ** washer four years and it broke down once again. I dont have any warranty and the money. They want to fix it. Im going to go out and buy something else. Piece of junk. It makes no sense. And when the first situation arose, I did ask if it had been recalled and of course, they said no.

One baffle broke off in my washer. Very disappointed in this Maytag Model #MHWE201YW00 Serial #HL20102420. I purchased this in Sept 2012. Where the baffle was hooked on had sharp fins sticking out that ruined my 2 small rugs - shredded them.

Purchased the Maytag Bravos upon recommendations from Lowes and Home Depot to replace a 20-year Kenmore that finally died. Since the Maytag brand was always considered to be the top of the line washers, we purchased the pair. About a week ago during the spin cycle I thought that a 747 was taking off in our laundry room. Called a local appliance repair service who said that there had been numerous issues with the Bravos series and to call Maytag to inquire about a recall. After 45 minutes on the phone with a very sweet naive young lady, she told me that the new models did indeed have a 10-year limited warranty on parts. However my 3-1/2 year old washer was not grandfathered into the warranty. I could (a) pay the $150 service charge to have someone come to inspect it or (b) buy a new one. I will be purchasing a new one but it will not be a Maytag or Whirlpool product. Now we know why the commercial for the Maytag repairman is not running... Hes now very busy working on their broken products.

I purchased the Maytag Bravos top load washer and the matching dryer at Home Depot back in 2009 after giving my son my very old Maytag washer and dryer that was running just fine. I liked the top load energy efficiency idea of the new Bravos and the large capacity of both the washer and dryer. Also, the Maytag name sold me, gave me confidence I was purchasing a quality product... WRONG. When it was delivered, there was damage to the dryer door, so a new one was ordered and mailed directly to me. Once it came in, I called to have someone come put it on. First issue, not a really big deal but disappointing.About one month into using the dryer, the top of it became so hot it could literally burn your hand. There was also an error message. I had purchased a one-year warranty, even though technically there is a manufacturers warranty on the product. A part had to be replaced in the panel. This happened twice. We then moved out of state for one year and the washer and dryer stayed in storage unused during that time.Fast forward to 2014 and the washer will not complete any cycle except the spin cycle. I keep getting an error message of OL which means overload. The machine is NOT overloaded. It literally takes me hours to get through one cycle of washing clothes. And they dont even come out clean. I called Maytag repair and they offered me a one-year warranty for $363.75 since the washer is having issues. They explained to me if its the control panel the cost alone for that is $383.00 not including labor. Also, the dryer take forever to dry. I have to run each load through a cycle twice to dry everything. So much for the energy efficiency of these machines. At this point, I am considering just buying another washer, something cheaper without all the fancy bells and whistles. I am terribly disappointed in Maytag.

First I do like the fact that it spins at such a high speed that the water is mostly gone, and that is the good news. I do like that it uses less water but when washing any dark colored clothes there are dirt or scum like marks where the clothes may have been folded or twisted in knots which I also do not like. I have cleaned machine but this started when new. Drying doesnt get rid of those scum marks either. I never had this problem with my old full fill machine. I have used more detergent and less HE of course in both liquid and powder. Any suggestions?

We purchased a Maytag refrigerator model # MSF25D2EAS on 10-22-2012 at the Home Depot in Tracy, CA. On 2-2-2014 (15 months) we noticed a puddle on the kitchen floor. Upon inspection, we noticed that the refrigerator was not working. Went over to Home Depot and were given the name and number of the authorized Maytag repair dealer (A and E). The technician arrived on 2-5-2014 and replaced the compressor on-off /overload relay and charged $243.82. On 2-16-2014 (11 days later), the same thing happened again. The technician came on 2-19-2014. This time, it was the compressor at a cost of $800.00 plus the $75.00 service call. One can purchase the compressor online for $300.00 and I am sure that A and E buys it for a lot less. We thought about it and decided not to get it fixed because we did not know what else would go wrong and how long would the second compressor last. We talked to the Appliance Departments assistant manager and were told that Home Depot does not give any kind of consideration and she had worked there for 11 years and had not heard of any problems. She was not telling the truth or she was not aware of the numerous negative customer reviews online. She also informed me that I should have bought a warranty. We have bought quite a few refrigerators in 50 years and they lasted for many years. Home Depot sells inferior products. Maytag must sell these inferior products at discounted prices and of course, some stores are looking for larger profits. I do not trust Home Depot any longer and will not purchase appliances there anymore. It was a very expensive lesson - the price of the refrigerator, loss of food (twice) and the stress it caused. We bought a new refrigerator at Sears and it was not a MAYTAG.

I have had this dishwasher for 3 1/2 years. Replaced the touchpad 2 years ago and now the touchpad is dead. I read all the other comments that are similar to mine and am thinking to replace this junk dishwasher. I will not be buying from Home Depot as they are selling cheap products that are defective!

wW have had this Maytag gas range for twenty years. It has performed well for that length of time (maybe longer). During that period I replaced one burner. Only complaint is that the oven does not heat as quickly as I believe it should.

First, the machine is a wrinkle monster no matter what I try. I wash my clothes on delicate cycle to keep the colors longer and so my clothes last longer. This has never been a problem with previous washers. I take them out IMMEDIATELY as soon as the door unlocks and shake them out and hang everything to dry. This worked great previously and I never had to iron anything or put anything in the dryer to get wrinkles out. Now, this washer wrinkles my clothing to an unbelievable extent so that they need to be ironed or a round in the dryer to relax them. This is true on Wrinkle Guard and using the delicate setting, set between medium and none on the spin cycle. Wrinkle Guard? I don’t think so. This thing wrinkles my No Iron shirts so they will have to be ironed or steamed.The washer leaves lint like residue most all of the time on dark clothing from day one. I most recently did a load of black only clothes that I did on delicate, soil level between med to extra heavy, spin speed between med and none, and, because of the dirty clothes issue, I had the extra rinse on. The clothes came out dirtier looking than they went in and looked like I washed them with a box of tissues and too much soap. They looked dirtier than before I washed them and had a whitish and lint like residue on everything. So I ran them through the same cycle/extra rinse again but WITHOUT any soap. Unfortunately I didn’t watch to see how much water the machine sensed that these loads needed and I didn’t see how much water was there - but I did for other loads after - see the next problem below. After the second identical cycle, the clothes had the same residue which I photographed and have enclosed below. (And still a wrinkled mess.)We have found that the water sensor can’t sense the proper water level needed and is likely not functional. Sometimes it seems like it might almost be be appropriate and sometimes not at all. Specifically, after I ran the black load through, I decided to try a small red load before my usual large blue load just to see how much water there was. Same settings as above, 6 small items that barely covered the bottom of the drum and the washer sensed a medium load. Certainly by volume of clothing this was not a medium sized load and if it goes by weight, it was the smallest load possible! Medium water level… These clothes seemed to agitate ok because they were completely submerged in water and came out clean. Then I did the much larger blue load that filled the drummer then halfway. This had so many more items than the red load and weighed way more. I tried the same settings as above and this time the machine sensed a SMALL load and the water level was barely halfway up the clothes, if even that much. So half of the clothes were out of the water and we watched and witnessed that the clothes did not agitate properly. This load came out like the black load so I ran the whole cycle again including the double rinse. This time, the same load was sensed to be a MEDIUM load although NOTHING changed except that the clothes were damp and lower in the tub as they were compressed from having gone through the entire wash cycle. They came out mostly clean, after the second wash, again, likely because this time they were almost covered by the water (2/3rds or so) and could move around a little better but still not great agitation.There almost never seems to be quite enough water so that the clothes are not able to move by the agitator and sometimes we watch and can see that the clothes above the waters never get pulled into the water. I understand that this machine may not completely cover the clothes but this seems way short on water and the fact that things usually come out dirty means something is wrong. There is often so little water that the agitator can’t possibly work the clothes into the water. So, next I ran an Oxi cycle and witnessed that about half of the items were not in any water and were only wet because of the filling cycle not because they were moved around by the agitator. How can the oxi do its job if the clothes aren’t in the solution of at least wet from the solution which I didn’t see as likely as the clothes didn’t seem to move through much if at all?Along with the same water sensing problem, why on earth isn’t there a manual water adjustment? If the water sensor doesn’t work, the other option is only the high fill setting. After finding my clothes still dirty when we first got it, I tried the high fill setting to see if this would help but the clothes still came out with that residue. This was the very first few loads I ran and was assuming it was just user error so I studied the manual and tried everything as recommended. Since reading that residue can result from too much water, I use the recommended sensing feature now. So, we can either have too much water or barely any at all…

I purchased a Maytag dishwasher four years ago and it has been serviced six times in those four years. Not just small things, main parts. Control board twice, control panel twice, and cleaning terribly the other two. They replaced the control board once and then would not do anything after that. I just got it replaced four years into this nightmare only because I bought a Sears home warranty plan and they are replacing it. I would never buy a Maytag appliance ever again.

I have a Maytag Precision double oven 850 series. The upper oven handle does not fit snugly and has been broken 4 times. I have had to order 4 new handles because the hardware does not seem to secure the handle to the oven door. There are no problems with the lower oven door.

I have had it (Model MDB6000AWB) for a few years now. It had to have the door replaced per recall. This dishwasher does not wash dishes well at all; need to rewash many items after going through normal wash cycle. Also, all spokes are burning and falling off, along with pans getting burn marks. I am not sure how safe this is anymore. I am going to purchase another dishwasher, but not a Maytag!

I have been the latest victim in purchasing a Maytag Refrigerator. Something needs to be done about the defective products they are putting on the market. I received 9/7/13 (yesterday) a new Model FW: 555 Complaints and Reviews about Maytag Refrigerators bottom freezer refrigerator. After being plugged in for 3 hrs, the temp was 60 degrees.. After 8 hrs same and 24 hrs same. I lost everything because of the defect. I notified the store 3 hrs after purchasing it and because I had it delivered on a Saturday I have to wait till Monday to get this resolved. I want everyone to read before buying a Maytag product.

I purchased the Neptune HE pair because they are front loading and can be set on pedestals to raise them to a comfortable working height, plus the brand and reputation are both excellent. I like that the chimes can be adjusted from low to high, or turned off. The front loading washers clean so much better and with a lot less damage to items than washers with center agitators. Looks are secondary, thats for sure. Functions like warm/warm cycles and being able to adjust to whatever load needs to be washed is really most important to me. Any appliances with a good, proven track record of reliability with few repairs is high on my list. Expensive appliances should be made to last and be of durable quality! No cheap plastic or weak-looking welds or components, thank you! Quiet operation and dependable cleaning and drying are top in my book, and this pair has exceeded even my picky expectations in total overall performance. They are 11 years old now and look & function like new! I had one minor repair on the washer at 5 years, and not a single problem since. With front loading washers, its important to keep the door open a little when not in use so that they dont get a musky smell. Ive gotten into the habit of using laundry boosters to help clothes, sheets, and towels smelling fresh longer, and putting a small amount in the washer drum has kept my whole laundry room smelling nice. Purchasing the pedestal drawers to set the washer and dryer on added extra storage to my laundry and its much easier for me to load/unload them at this comfortable height. Im totally spoiled by it now, so when I use someone elses laundry room (when I visit) I am reminded how nice my own setup is.

Started having problems summer 2017. My dishwasher leaked and tank replaced, followed by drain pump, followed by circuit board in 2017. Didn’t have use of it for months. It has started leaking again as of Sept. 17.

Maytag washer Purchased December 2016. Washer is very slow: runs 1 hour plus. Wash takes a VERY long time. Small load only. Heavy loads go to Laundromat. Maytag does not clean clothes, always MUSTY smelling. Cycle OFTEN does not drain tub And forced to use Drain, Spin cycle to drain tub. Wrinkle cycle ties clothes in knots. Using AFRESH to clean tub makes no difference in foul odor. One service call, error codes found, computer reset. Repairman said that the MACHINE WORKS AS DESIGNED. Repairman said that any tiny bit of debris can cause washer to clog and fail to drain. At best clothes always wet, slow to dry. My old Whirlpool washed any sized load. Clothes always clean and fresh. I used laundry only when we had power outage. LIKELY WILL PUT THIS ON THE CURB. I DO NOT RECOMMEND THIS MACHINE.

Model MBF 2258XEW3. I am very annoyed with this fridge. Never will buy a Maytag again. I went to this site to see what the problem with my fridge was and read that I am not the only one with this problem. From the beginning it never worked right. Often the food in the fridge got ice crystals in them so I had to up the temp. This made the freezer not cold enough so I had to lower the temp again. This is a constant affair. Now the bottom of the freezer is collecting an ice sheet or a water bath that has to be removed every other day so that it doesnt built up or leak out. Will have to buy a new fridge. But now I am worried that I might buy another lemon.

I purchased the Maytag MFI2670XEM0 3 Door Refrigerator in Oct 2012. Thank God I purchased the extended warranty. The freezer has had issues with improper sealing since I bought it. It builds up ice around the bottom of the freezer where the seal meets. So bad it prevents it from closing. It happens fast, so I have to scrape it off every week minimum, to keep it closed. They have replaced the seals twice, all of the slide rails, twice and it still doesnt close right. I thought when I moved to Florida, I wouldnt have to scrape ice.Next: Ice maker quit working and had to replace that. Now, I came out this morning and about busted my ** when I slipped on all the water flooding my kitchen. The ice maker has a stupid little fitting on top of the refrigerator that has a rubber bulb connected to the ice maker water line. It split in half and every time the ice maker cycles, it pours water out that fitting and down the side. Why in the ** did they design it like that? It has caused damage to my cabinets and tile floor from running under it.Im sick of this appliance. I thought Maytag was known for quality. What happened to that? What a disappointing piece of junk and Im stuck with it unless I want to put out money for something different. There should be a Lemon Law rule for appliances like this. I have asked and get nothing from the warranty service but silence (crickets). They are sending out a tech again but that will require two service calls because they always have to order parts, which takes 2-3 weeks. Ive had to call them at least 5 times, which has amounted to no less than 10 service calls and here we go again. Stay clear of these units at all cost.

It has never failed me and I cant remember when we purchased it. When I grew up, my Mother only used Maytag Washer and Dryer. When I married (almost 50 years ago), I purchased a Maytag Washer and Dryer and have never regretted it.

Maytag Dishwasher Model MDB6759AWS3 Does Not Start - If you are having the following problem, here is what I did to fix it. All of the lights on the touch pad would light-up when pressed but the dishwasher would not start. It appears to be a corrosion problem on the connector from the touch pad to the control panel. 1. Turn off power to the dishwasher. 2. Remove the inside cover to the dishwasher door - approximately 10 screws. 3. Disconnect the electrical connections from the inside cover to the control panel still attached to the door. These are snap connectors. Always a good idea to label the connections before disconnecting in order to make sure everything goes back together properly. 4. Remove the black cover on the control panel. There are 3 screws. 5. Find the green conductor tape that connects the touch pad to the control panel. 6. You will remove the green conductor tape from the control panel. DONT just pull on it. There is a white piece of plastic that slides away from the control panel and toward the green conductor tape. It will remove pressure from the conductor tape and the conductor tape can then be disconnected from the control panel. 7. Get a good pencil eraser and clean off the exposed copper connectors in the conductor tape. 8. Place the conductor tape back into the control panel and slide the white plastic piece over it to reconnect the conductor tape to the control panel. 9. Replace cover on the control panel. 10. Reconnect the electrical connections from the inside cover to the control panel. 11. Place inside cover of the dishwasher over the proper screw holes - make sure the bottom of the inside cover is overlapping the bottom of the door - or the door wont shut properly. 12. Replace screws.13. Turn on power and check.It worked for me and saved me time waiting for a repairman and expense of the repair.

The microwave is 5 years 6 months since purchase model MMV4203DS. Fire started at rack clip left front rack, was cooking bacon. Called Maytag and according to them and manual on page 3 is only for 2-level cooking to avoid damage to microwave oven. DOES NOT SAY WILL CATCH FIRE OR THE RACK CAUSES SPARKS AND BACON SHOULD NOT BE COOKED IN A MAYTAG MICROWAVE. But according to Representatives of MAYTAG ** its my fault for not reading my manual. YES AND NOT HAVING THE SERIAL NUMBER THAT IS ON A PAPER TAG IN THE WHIP ZONE. The was gone from keeping it clean faded out. So I cannot be helped without the model and serial number.

Bravo XL - I purchased this dryer in June 2012. In October, the first thermostat was replaced, again in February 2013 and two within a week from March 8th and March 12th. I was told it was my vent. However, the appliance continually showed venting good. I was told to have it cleaned. I did and it is documented that there was great air flow before and after and only a handful of lint collected. I have spoken with Whirlpool and no one will have the integrity or courage to say it may be a faulty unit. I will never purchase another Whirlpool product. I had spent nearly $5,000.00 in Whirlpool appliances in June of 2012. I feel they will cover any issues until the warranty is completed, and then the problems are mine and at my expense.

Purchased Maytag Dishwasher Model MDB7749SBW3 in April 2014 along with other Maytag appliances to go into our home in the Georgia Mountains. Purchased Maytag for 2 reasons: 1. American made 2. Reputation. Bottom line, after just 2 years the dishwasher has failed. I prewash by hand everything that goes in. First the normal cycle stopped working. Then lights on front panel would randomly turn on and dishwasher would turn on by itself, and run for hours. I suspect this could be a fire hazard. I have tried front panel resets, cycling power, etc. Nothing works... It is really sad that American products are third world. I will replace the board myself in hopes of getting another couple of years out of it. No more Maytag for me. Rest assured every time I see someone in Home Depot or Lowes, looking at Maytag appliances, I will go out of my way to warn them.

I bought my washer in 2016 and now it’s broke again. This is the fourth time! I’ve gone everything to take care of this and it’s a lemon! I will never buy Maytag again. I want to buy USA products but four times for repairs in three years is way too many. I guess it doesn’t matter what name is on it. My last washer was a GE and was still running after 15 yrs when I bought this one. Not one repair ever made on it! I’m telling everyone to stay away from maytag.

First off. Maytag customer service is horrible. I purchased a Maytag washer & used it 8 time. It now doesnt rinse the soap out of my clothing or even clean anything. The washer isnt broken because thousands of other people with the same exact washer have written negative reviews everywhere online. The washer needs to be recalled & never sold again. Maytag is making people SICK and they dont care. My whole family had skin irritation because we didnt realize our new washer wasnt rinsing.

Our $1,000.00 Maytag Bravos is only 4 years old (also bought the matching dryer at the same time). We have had to purchase two new motherboards for the washer and now the uL, during the spin cycle, comes on and my clothes will not spin out. I have followed the manuals directions to unplug, wait, replug, redistribute, etc... all to NO avail. So very disappointed with this machine. Bought it because it was a Maytag, but will never buy another :( I had this machine repaired with major amount of parts and expense (due to the uL problem), BUT the uL code still keeps coming up. I am one really unhappy customer.

We bought a Bravos model in May 2010. Two years later, the machine started making noise during the final spin cycle. We finally called a repairman who came today and informed us it was a bearing in the outer drum. The cost for the part (the drum assembly) was $290, not to mention the cost for labor. Since we only got the original warranty, the service center at Maytag refused to help with the repair. We, as others who have had problems with Maytag, bought the washer because of Maytags reputation. This is why we have to buy extended service warranties. Companies make trash! What happened to the days when an appliance lasted longer than 10 years? Why cant we buy a good sturdy appliance without superficial bells and whistles? We have no idea if any other brand is better, but we will not buy another Maytag.

I just purchased a washer in April and the door is locked with my son brand new clothes is stuck in the machine in water, I called to get service and was told a date 2 weeks away, worst experience ever. Sorry ma’am is what I was told in a non caring way. I’m so furious if I could return this washer and dryer I would.

My Maytag over the range microwave has given me nothing but troubles since my purchase. The turntable off feature never worked, and now the side control panel is barely hanging on because of broken plastic connectors. The handle is now broken in half. I will never purchase another Maytag product. Buyer beware.

Sometimes the control panel is difficult to work with especially if the wash is paused to add more clothes or detergent. The good things is that the tub is very large so a comforter can be washed and you can control the amount of water depending on the amount of what is being washed. I also like that it doesnt have the big agitator in the middle.

Dishwasher is around two-three years old and it will not start or drain. From what I can tell on the internet, this touch-pad control panel has been an ongoing problem for Maytag. Will try to fix myself, and if I cant fix it, I will buy a new dishwasher but not a Maytag. By the way, my washer and dryer both went out this year - five years old and both are Maytags. Stay away from this brand.

Bravos XL Top loading High Efficiency Low Water Washer and Dryer - I gave this washing machine a 1 star but would give it a 0 star or less if the choice was available. I agree with everything others have voiced about this washer. I end up using the bulky cycle for everything because it is the only cycle I have found that will use enough water to get the clothes moving around. All the other cycles are a joke. First you must put everything around the wall of the tub away from the so called agitator. Then about 2 cups of water enters the machine. It then goes into this high speed spin. In my opinion it just pushes any soil deeper into the fibers. The drum will then spin slowly and water will spray on the clothes for several minutes but the washer never fills with enough water to cover the clothes. Watching it agitate through the glass top is almost hysterical. Laundry is barely moving. The high speed spin they push as a selling point puts deep wrinkles in everything and the wrinkle control setting on the dryer does nothing for them. It is absolutely the worst machine I have ever owned. My husband has repeatedly told me to sell these and buy another set. I will be ashamed to sell it to anyone. Im not sure how the makers of Maytag got away with selling these machines. I know there are different models but from what I have read they all work the same. I replaced a very low end GE Washer and Dryer with this pair and every time I do laundry I wish I had them back. The matching dryer is very costly to run as almost every load takes 2 cycles to get items dry. Nothing comes out completely dry even if you put it on the more dry setting.

HORRIBLE. Dont pay more for substandard machines. Had a Maytag washer and dryer delivered on March 27th 2018 and it has been a nightmare to get it to start up. Now I have clothes stuck in there. I called Home Depot, you should never buy any appliances from them, they wash their hands of all responsibility once you sign for it. Called Maytag. On hold for almost 10 minutes, they only have 2 certified repairmen in the area 0f 600,000 people. Will be 5 days until they come to look at it. I told them I wanted to return it for a GE or something else. They said I had to contact Home Depot yet Home Depot told me it was Maytags problem. SAVE YOUR MONEY!!! MAYTAG IS NOW AN INFERIOR PRODUCT WITH EXTREMELY INFERIOR SERVICE.

Like so many other people reviewing Maytag refrigerators with bottom freezers, I am dealing with water on the floor. At 64+, I am not eager to tackle the problem as a DIY project. Once of defrosting and cleaning up was enough. I love the looks of my 2 yr old $2000 4 door fridge/freezer but hate the issues. I guess Maytag is going to ignore all of us. When someone finds a reliable company, sing it from the rooftops.

We purchased our Maytag dryer at Home Depot a couple of months ago. We just called Home Depot for the second time because the dryer handle broke off while opening the front load door. We called Maytag and they tell us to call Home Depot and the only thing they are willing to do again is fix the door handle which will probably break off again while Im in the middle of laundry and cant retrieve clothes from the dryer because there isnt a handle to open it.Im convinced the dryer has a defective handle, and the dryer should be replaced considering what we paid for it. But Maytag or Home Depot doesnt want to do that. I will never buy Maytag products again and thinking of buying products at small appliance stores who stand behind their products, instead of Home Depot who could easily turn our dryer over to the insurance company as defective for the loss.

Used my washer ONE time and when the load was done my clothes were soaking wet. Tried to get the clothes to spin dry but the washer would not work. Called for repair. They replaced the activator. I did one load of laundry. It worked fine. Did a second load of laundry and the clothes were soaking wet. The washer would not do anything else.

I have a major complaint with the Maytag double oven design. With the smaller oven above, if you spill any liquid while taking something out of the top oven, the liquid drips down between the two panes of glass on the lower oven door. This makes it impossible to clean. Maytags reply - call a service rep and have him make a house call and take the door apart for you and clean it. Not warranty work so I would have to do this every few months. Also, when baking in the upper oven, cakes and cookies tend to overcook on the bottom as the dishes are so close to the element.

The washer we bought has a leaking drain pump after 3 years. When I called, they initially told me the part has been flagged as a potential quality issue. When I was passed to the next level to deal with it, they stuck to the you only have a 1 year warranty policy. There are numerous websites indicating this has been an issue for these brands. Simply put, they dont stand behind their products.

Ive had my washer and dryer since 2007. We purchased a new vacation home and it was included. I used the HD washing machines at my daughters, though hers was a front loader from a different company. Im unhappy with mine. Would not purchase one again. I find my clothes arent clean and my kitchen clothes and towels always have a residue on them. I now wash everything on warm, use the proper amount of soap and have to do heavy load cycle. Im still not happy, but it beats buying a new one.

We were offered a Maytag microwave with our newly built home two years ago. I do not know if it was a good value for the money compared to other brands as I did not price or feature shop for this oven. But the oven has worked well since we moved in.

I bought a full kitchen of Maytag appliances when I bought a new house in 2009. I thought it was a reliable company. Id always gone with GE before. I couldnt get the packing sticker off the oven after trying everything to remove it, so the oven bottom is virtually ruined. The timer on the oven dings once and stops; dinner burns if Im not right there to hear it. I was told by customer service thats the way it works, so I had to buy a separate timer. I am now replacing my 2 ½-year-old dishwasher because the control panel has once again stopped working. It cost me $275 to fix the first time and it lasted less than 3 months. I will never buy Maytag again! I got over 20 years of service from my GE appliances.

Within the first month of purchasing my front loading Maytag Neptune washer (MAH6700AWW) at Home Depot, the soap dispenser fell off. The machine not only leaked, requiring stack of towels to be placed on the floor to keep the room from flooding, but often produced foul-smelling clothes, despite cleaning the machine. On top of that, the delicate cycle stopped working and then last month, the entire control board went! It is past its warranty period, and I cannot afford a new washer for my family of 6. The machine has been discontinued and the parts unattainable. The control board of our dryer (MDE6700AYW) went too, causing buzzing in the electrical connection and burning, causing us to have to shut down the circuits for the machine. Maytag has lost all my respect as a quality appliance supplier. We spent $1700 on the set and the machines have been a nightmare. Please note: we were NOT notified that there were class action suits against Maytag regarding their machines.

I have never been so disappointed in purchasing an appliance for my home. The Maytag Bravo XL large capacity top loader, has never worked properly, and I have many ruined pieces of clothing. Although it has a very large capacity, the water barely fills to a 1/4, and clothes are sticking out of the water, while they are supposed to be submerged/being washed IN the water. Clothes come out of the washer smelling foul. WORST WASHING MACHINE EVER.

Im currently standing in front of my washing machine waiting for the 13-minute drain and spin cycle to finish because once again my load didnt drain and finish right. Except it has already been 40 minutes and it claims there is still 9 more left as it continues to sit there doing nothing while it hasnt even started spinning yet. It Sat on 13 minutes while sensing for over 5 minutes, then 12 for 10 minutes while doing nothing, then it changed to 11 minutes and made some weird noises but didnt actually do anything for 15 minutes, and now the timer randomly changed from 11 to 9 without any noises or movement happening and now continues to sit here.I stupidly thought I could spin my clothes real quick to throw them in the dryer before bed and now I stand here extremely tired and very irritated. I also have no doubt some of the clothes will have holes in them when theyre done because they always do, my family looks like were homeless and ratty half the time we get dressed now. Also it never deep cleans thoroughly even on the toughest settings, I swear our socks can be washed 3 times in a row after being soaked all day and still come out crusty or a lot of times the armpits of shirts will still smell or be ultra stained with deodorant marks still.This technology is almost too advanced and everything is decided by sensor, regardless of the registered functions on the buttons it will still do what it wants as the sensors see fit and run when they decide everything is perfect and ready, including taking 10 minutes just to unlock the lid when you pause a load cuase a small child may drown in the foot of water or a person may have their life completely altered by getting a little bit wet if the machine isnt completely drained and in pristine condition before you open the door. This machine is terrible. This company is terrible. And worst of all they drain your wallet for these horrible contraptions. I wish I could rate this 0 stars.

We purchased a 3K Maytag refrigerator/freezer and purchased an extended warranty as well. 5 months later the ice machine stopped working. We called Maytag to get it repaired since its under the 1 yr factory warranty and they sent an appliance service company they contract with to repair it. 6 service calls and two months later its still not repaired. I called Maytag back to say if you cant fix it please replace it. They say it needs to be deemed not repairable to even consider replacement and that they would send out a different repair company. As of yesterday (9/(9/14) another month and a half and 5 trips from the second repair company and it still does not work, so I call Maytag again to complain and they give me the same line ....needs to be deemed unrepairable... How long and how many service calls does it take to fix a ice maker? How much work and how many hours do I need to miss to get what I paid for? I went to their website and it talks about how their mission statement is customer service etc, etc, etc..... Thats just a bunch of lip service and judging by the HUNDREDS of complaints I have read this is their standard method of operation.... I for one will not let this go and will be filing a claim in small claims court to get what I paid for..... BE WARNED if you are looking to purchase a appliance.

This has to be the biggest joke in the world for the respected name of Maytag! The engineers that developed this worst-of-all machines on the market must have been circumcised with pinking shears. 80 minutes for a wash cycle? Even rapid wash takes an hour of slowly spinning and spinning ad nauseam with almost no water. The clothes sit in the same position even on the very brief agitation cycle... Nope, the clothes do not come out clean, although if you add bleach to the dispenser, since there is no water in the tank, the bleach does triple duty and rots the clothes. Is this masquerading as energy efficient when all of the cycles are an hour long, about? Unfortunately it takes water to clean clothes and the environ-lack-of-mentalists must have bribed Maytag to develop the worst washer on the planet. Absolutely!

Unless you’re doing laundry for an army don’t buy the Maytag commercial washer MVWP575GW. I should have gone with my original choice but my husband was concerned with the durability and warranty hence why we purchased this washer. It’s just the 2 of us and I frequently use the delicate cycle. Unknown to me at the time you can not adjust your water level so if you’re washing delicates plan on wasting a lot of water unless you only wash your delicates once a month. In my opinion delicates are undergarments, blouses, etc. delicate cycle in “deep water wash” only. As far as we can tell the wash cycle at its longest is 8 minutes which I guess for commercial grade is probably correct. However there is a presoak option that I don’t the believe does the work of a longer wash cycle. If you have to do a quick scrub on a piece of clothing as the washer is filling up you can not do this as everything stops once the lid is up.Last but not least the washer is loud it sounds like it’s going to break down at any minute. I’m sure many of the issues people have with products today are due to government regulations. I’ve tried contacting Maytag customer service on numerous occasions to see if I’ve been doing something wrong even though I’ve read through the operating manual several times, I’m currently on hold for 20 minutes. Doing the laundry has never been the highlight of my day but I never minded it until now. I absolutely dread it now. My suggestion would be if you like the features on your current washer, spend what you need to to get it working properly which is what I wish I had done with my 23 yr old washer. Worst purchase I’ve ever made!

Two and a half years ago I bought a Maytag dishwasher thinking it was time to upgrade from my Ge. After a year and a half the control panel went out in in it! So For a little over a $100 I replaced it. Now, a year later, the panel has gone out again!!!! What is this? Every year I have to spend over a $100 to repair this thing!! I think it is time to find a new dishwasher!

My 1 year old Maytag Bravos 300 dryer caught fire on Nov. 21, 2011 after the first one was replaced. Firemen came. Luckily, it didnt spread to the house. The first one wouldnt dry my clothes.

Bought the washer last week. Balanced it per installation instructions. Washed several loads. The darn thing goes off balance almost routinely. Have rechecked the level on several occasions and found it LEVEL. Contacted Maytag. The lady I spoke with said to just use it and it will level itself out. So much for Maytag help! This will be the LAST Maytag product I buy.

I purchased my dishwasher exactly two years ago. We are empty nesters so it has had light use. Today, when I tried to start it, the control panel would not work. Thanks to what I found in your site. I will not take a day off of work to wait for a repairman only to have it fail a second time. It is hard for me to believe a company that builds its reputation on a bored repairman would produce a product with a faulty control panel and not do something about it. Like your other folks, I will never buy another Maytag product and will not the waste the money to repair it. I am going out tomorrow to buy another dishwasher and throw this one away.

7 years is all I got from these appliances. The Maytag Washer started making a horrible noise when washing then smoke and shut off. Dryer would not shut off. We have taken excellent care with these appliances servicing them as we had an extended warranty on both. They cost us over $600 for the washer and $589 for the dryer, a big rip off! I purchased them in hopes I would at least get 15-20 years of service as Maytag is to be one of the best. Do not purchase any products from this company, they also have sister companies. Make sure when you need an appliance, you ask who makes them.

We purchased our Maytag Bravos just under two years ago. Over the past month or so, we noticed the spin cycle was getting louder and louder. Today we had the service man come out. He informed us that our 2-year-old machine will require new bearings and a new basket, which equates to over $700 in repairs. The repairman said he has seen more and more of this with these high efficiency washers. He suggested that anyone buying these new washers be sure to buy the extended warranty.I for one am completely disappointed that one can spend that much money for a washer with a two-year shelf life. I personally think this is planned obsolescence created by the manufacturers. The serviceman also said the LG versions of these washers have a large increase in electronic problems. Be warned, we have very few choices these days so buyers beware.

We purchased a bottom freezer refrigerator from the Home Depot in 2013 and I am sorry to say this refrigerator does not deserve any stars. Immediately after the warranty was up our refrigerator started leaking all over the floor. The drain clogged and freezes up on the bottom under the freezer. When it becomes full, it leaks all over my hardwood floor. I have now become a slave to this refrigerator. Each week I have to open the freezer and get down on my hands and knees to break up the ice, scoop it out, toss it in the sink. I have spread the word and I hope anyone who reads this does as well. Never buy a Maytag product because not only do they make defective products, they wont own up to it and recall it.

I purchased a beautiful Maytag dishwasher for $700+ and it died after a year of use. I called Maytag to complain and they dont care. Pay $350 for a tech to come fix its warranted for a year or fix it yourself. I fixed it myself for $180 and am hoping the very same key panel wont fail again. I know it will. I wrote to Maytag about the issue and have not gotten a response. Im hopeful that they will make this right or that they get sued and the consumers get their money back.

This is the worse washing machine ever. Wish Id never have bought it. Clothes come out unclean, washer cleaner cycle doesnt work, water level is almost none, etc etc. I could go on and on, you get the picture. Coming here and seeing 100s of negative reviews and complaints many of which I suffer from as well, just clarifies how bad this machine really is. There has got to be a way to bring a class action lawsuit or arbitrary suit against them. Im pretty confident that there are probably 100s more who are dealing with this shoddy washing machine as we all are.

Bought a Maytag front load washer. When it is operating it is very loud. Some parts of the washer are made of cheap plastic. The Optimum detergent dispenser also of cheap plastic failed after 1 month. Disappointed in finding out only the outside metal box was made in America. All inside components are made in China which raised the cost $300 due to recent tariffs.

In May of 2009, my husband and I bought a new Maytag refrigerator side-by-side, model MSD-2572VEW. The day we bought it, pieces started breaking. The shelves started cracking, and now they are completely falling apart. There are also cracks in the inside walls of the refrigerator. Every single door shelf, inside shelf and wall is falling apart. I have fixed the ice-maker myself several times. I am now going to design and build some new shelves so that we can get as much use out if it as possible before it is unusable. I am angry that a company can make such a horrible product and not have to take responsibility. If my employer ever provided a client anything but the best, we would all be out a job.

We updated our kitchen appliances in 2013 and purchased all from Home Depot. Purchased Maytag Refrigerator, free standing range and microwave. What a big mistake!!! Not one of them are worth what we paid for them. I just noticed that I was getting a (chemical) smell from inside our 6 year old 3 door model MFI2670XEM5 refrigerator. Well being I know what refrigerant smells like I have a leak in the interior of unit. This is my final issue with Maytag and their so called great built appliances, I have had nothing but troubles since about 2 years after we purchased it.I guess what really surprises me is that unit is built by Whirlpool and has their name all over unit and I always had good luck in the past with the brand. This is one of several issues including rust on freezer door, broken plastic drawer frames to French door hinges broken, ice maker door issues. What a waste of my money that I spent on these and now after 6 years need to buy all new. IT WILL NOT BE Maytag or Whirlpool!!!

Dishwasher is just 2 years old. Touch panel is bad, not Maytag of old. Waiting for the corporate apology. Seems to me that this is a common problem and a case of poor engineering. Also seems like a case of the middle American getting worked over by the big corporate giant. Not happy. Will not suggest Maytag to anyone. Not looking forward to having to replace something that should have lasted significantly longer.

Like everyone else Im calling corporate. Mr Fettig he should be in hall of shame after these complaints with their defective product. My fridge leaking, ice maker broken, water everywhere and eight inches of ice. I wonder if he owns a Maytag himself? Oh well after a while he might have a flood on his floor. This should be recalled just like my first model in 2001 that was a fire hazard. I had to go to the top then and I will now also. We should be protected from buying garbage while he makes 4 million a year.

Its about Maytag MDE7600AYW Atlantis electric dryer issues, Nov 2005 model. There is an obvious design flaw. I have replaced the automatic dryer control board twice since 2005. The unit simply never shuts off, or cooks your clothes for 2 hours. Who will recall this unit and fix the circuit? They will not admit their error.

Bought a Bravos, large capacity, top load washing machine few years ago. (Purchased at a Lowes.) Been nothing, but one problem after the other!! I hate it! NO MORE MAYTAGS FOR ME. Has required several repairs of various parts. Now again, after being repaired few months ago, something else has gone wrong. Would have been cheaper to replace a 3-4 year old machine than keep having repairs.

I have had this washer (Maytag Bravos) less than a year and it does not clean my familys clothes at all. I have had to throw away clothes that are stained and ruined because this washer does such a poor job of washing. For the cost of this appliance, I thought it would do an excellent job, only to be disappointed. I have owned other Maytag appliances without a problem. This one is a disaster and has turned me against Maytag.

Model MDB7749SBM1, Complete FALSE ADVERTISEMENT and GARBAGE. Let me explain. Maytag clearly claims this dishwasher is stainless steel on the inside and out... FALSE, BOGUS CLAIM. Please check for yourself, tried a magnet to it everywhere and the magnet stuck everywhere. I have had this dishwasher for 15 months. The keypad frequently stuck. When I called Maytag, they told me if its usable, there is no defect. 15 months after purchase and 3 months after WARRANTY ran OUT on Thanksgiving Day with 25 guest. The keypad finally quit for good. I called the Friday afterward and was told no service for a week. I called and received local service but they told me it would need a keypad, which I waited to call on Monday since Maytag is closed on weekends how ironic. I was told they wont cover anything since a certified person didnt come out even though nothing was ever fixed and they blatantly lied to the consumer. Tried to sell me an extended service plan. I will NEVER BUY ANOTHER MAYTAG PRODUCT AS LONG AS I LIVE AND WHEN IM IN LOWES OR HOME DEPOT, I WILL TELL EVERYONE IN THERE SHOPPING THE SAME THING, DONT BUY MAYTAG IF YOU KNOW WHATS GOOD FOR YOU.

Maytag refrigerator - After 3 months, a water line broke and caused $350 in damages to our kitchen floor. The next month, the ice maker jammed. The next month, the ice maker went out. I have agreed to let the Maytag repairman (youve seen the commercial where he never has anything to do) use our spare bedroom. Seriously its the worst appliance, by far, Ive ever owned and Ive had plenty as I am 71 years old.

I bought a Maytag dishwasher (MDB7749SBW1) about 4 years ago. Ive had to replace the wiring on the control panel each year. This is clearly a design defect, and Maytag will not take any responsibility for it. Ive called each year, and am told each time that theyve never received a complaint about this issue. This year Im replacing the dishwasher. Ill never buy a Maytag product again.

Purchased a Maytag washer for my family of 8 because we do a lot of laundry and our Samsung washer failed after 3 years. I thought Maytag was a more reliable brand and was hopeful. The machine stopped working after less than 4 months of service. Manufacturers warranty repair came out and said it needed three new parts, motor, clutch and chip - said it would be another 2-3 weeks depending on parts. So all total without a washer for 4 weeks minimum - call the customer service people (first one was rude and short), 2nd one after 45 minutes on hold - told me the were no other options other than wait for the repair. Four months after a brand new washer and it failed. I requested a replacement option and they said no way. Their hotline talks about a positive customer experience and that seems to be a joke. Not helpful, super frustrated and they do not seem to care about the customer experience at all - terrible product and service

Very Poor Quality from Maytag Although (Dishwasher, model MDB8959AWS) - I knew Maytag always had a reputation of selling quality products I have never purchased a Maytag appliance because they usually cost more than other brands, so this is my 1st Maytag product. After ~25 months (after all warranties have expired), the unit stops working. The lights seem to have a mind of their own. I removed power from the unit for 1/2 hour attempting to re-boot the computer but the condition did not change. After researching the issue online, I found that Maytag has a two big problems: 1) Defective dishwashers, 2) Bad or no customer service.I am an engineer and this type of a problem (it happens from time to time) MUST be acknowledged and the customer made whole or the reputation of the company is destroyed and future sales will (and should) diminish to the point that the company may(?) go away for ever. I know products are not designed to last a lifetime like they were in the 60s & 70s but 3.3 years for a $650.00 appliance is way out of line. The dishwasher we replaced was ~18 years old, and we only replaced it because my wife wanted a more modern look.

I purchased this on sale at Home Depot, 1 year later this washer top load doesnt clean clothes if the cycle does finish at all. I have to restart the cycle, re-rinse etc, theyre still dirty. I dont have time for that, I have four children and my husband works in construction and comes home with filthy clothes that are just wet and dirty when they come out of this washer. I dont usually write reviews but I hope I can save someone else the hassle. I wish I would have read the reviews beforehand, they all complain of the same thing. This washer altogether is BAD! ITS LOUD, it bangs around if I dont put in the tiniest loads, even then, they come out dirty. Dont waste your time.

What a disappointment. I guess this is why we no longer see that commercial about the Maytag repairman being bored. Because now, he is out fixing these pieces of shirt. Im trying to fix my washer (Model: MAH8700AWW), what a sweet pain in the **. Dont do it. Throw it away if it starts making noise like an aircraft landing.

Maytag Neptune MAH8700AWW and MDE9700AYH Washer and Dryer - Electrical overload to house circuit, multiple water pump replacements (Maytag would not sell rebuild kit with impeller and gasket or seal causing us to have to buy complete water pumps with mounts and motor.), electronic error readouts, odor and mold washing machine. The welds breaking on the drum causing possible fire hazard by filling case up with dryer lint fibers, around the electrical components, and air intake heater and also allowing metal fragments to get imbedded in the familys clothes. Also, Maytag Oversize Capacity Plus Quiet Pack Heavy Duty with Lifetime Tub.

We bought a refrigerator June 4th 2014. 6 month ago the freezer and refrigerator was getting warm. Had to call repair service, it was the blower! On Saturday 12/9/17 freezer wasnt freezing, then fridge was clicking on and off. Unplugged it, called repair service, it was the compressor. $800.00 to fix it, the same amount as when we purchased it. Repair service told us to call Maytag, he said, Maybe they will help you, would not help at all. Talked to Lori, all she said was warranty is up after a year, I then said, I think a refrigerator should last longer than 3 years! Will never buy anything Maytag again! Yes Maytag does SUCK!!!

Below is the message I submitted to Maytag on 5/6/2016 at 10:00 a.m. ET and just received an answer via phone call today 5/9/2016 at 3:30 p.m. ET that Maytag will be doing nothing. Also, my husband has still not received a call about the drum seal and when Maytag can come fix this part that broke in their machine only months after purchase. I will let you read my message to Maytag and you may decide if you would like to buy their dryer after reading what I sent and knowing they will be doing nothing. (Washer works just fine).If this message could be passed onto customer retention and/or management, I would greatly appreciate that action being taken. My husband, and I purchased a Maytag Washer and Dryer Set from Lowes in (Listed Location) on (Listed Date) (Model Number: MGDC555DW2 and Serial Number: **). The dryers drum seal has already gone bad on one side. We had a Maytag servicer come to our home on Monday, May 2, 2016 to confirm this and said he needed to order parts and we would hear back from him on my husbands cell number in a few days, which we still have not received contact. Additionally, due to the drum seal going bad, a whole load of laundry has extreme tears in the material to the point of being ruined. I have pictures of the clothes/sheets and drum seal, however there is not a location on this contact form to upload them. I have three work shirts, worth around $30.00 each and new bed sheets just bought in the amount of $77.39 which have full threads pulled through them due to the dryer going bad in only four and a half months of normal usage. I am writing to request compensation for my items that are now unwearable/unusable and would be glad to provide pictures and receipts for price of items. We of course have not used the dryer since, which has been a huge inconvenience, especially with no update in knowing when the dryer will be fixed and reusable. Please contact me back in regards to my request. Thank you.

Bought the xl about 14 months ago. NO LIE! Exactly 2 days after the 1-year warranty was up, the xl went down. Drive shaft and bearings. Did Maytag honor the warranty since it was only 48 hours past the expiration? Not just a no but a why are you bothering attitude. My brother and I are above average machine builders. Well fix it ourselves because we could buy a new one to have it repaired. After many hours scouring the web we found the parts. Maytag didnt make a repair kit available to the public. 7 hours plus over $200 to tear it down and to clean the muck trapped at the drain. Then sand-smooth the burnt on metal where the bearings sit. All for a washing machine that sucks at washing clothes in the first place. Never ever again will I buy a Maytag.

Every appliance in my kitchen is Maytag. I went with Maytag because its made in America and now Im annoyed. The microwave died after about 5 years and since I had a spare, I have yet to repair it. I am just now removing the panel to see whats going on in the inside so I can replace whatever broken part is broken. The double oven I have Ive had to repair twice. Once I had to replace a capacitor on the board because it blew. It cost me zero to replace it as I have an old home theater system I part out. The next item was the control pad itself which I tried to repair but had to replace for $200. The dishwasher died after 6 years of use and after replacing the control pad (couldnt be repaired), it still didnt work. And I got a replacement from my wifes dad who was moving and had to get rid of his. Ultimate timing. I purchased a Maytag refrigerator instead of a Samsung like an idiot (which I suppose I am at this point). The fridge leaks water because the drain plug is jammed and it will take a lot of work to get back there to unjam it. I think Maytag wants to sell you expensive parts that are doomed to break after a couple years of normal use. They want to send repair guys out to your house to charge you to fix their junk. I cant wait to move and buy all Samsung products and do away with this Maytag relationship once and for all.

I bought a Maytag washing machine, model number MHW6630HW2 in January 2021. It works fine on ordinary loads, but it cannot spin the water out of bulky items, not on any setting. I put my machine-washable winter coat in the washer and it left it full of water. I re-tried on 4 different settings, and though the washer spins, it cant spin out the water. I went to the Maytag support site. The sites said my model doesnt exist. The phone number for support does not allow you to get any support other than a service call. The Chat option doesnt give a lot of support either. They said that if I call for a service appointment and the service technician finds that the machine does do a spin cycle, then the appointment is not covered under warranty.

Maytag is the brand I had for 18 years and never had a problem with the washer or dryer in all that time. So when my dryer died I decided to get a new set of Maytag washer and dryer. I picked the set together and they dont have a lot of bells and whistles, simple to use and the washer is an HE. Cost was about $900 for the pair. I bought the washer and dryer in May of 2015. Models are simple to use. I have not had any problems and quite pleased with the work they do.I like to stick with a brand if it has served me well. Energy costs need to be low and I look for sales. Capacity is something I do not need a lot of, since it is just two I am washing for. Good quality is what I look for. I have not ever had paint chipping or rusting. Never had socks missing or a bad result with cleaning or drying. The washer has a cleaning cycle and the dryer is very easy to clean, the lint filter, and I get great results with no static when I take clothes out of the dryer.

Has anyone talked to an attorney to see if a class action can be filed? My fridge is leaking, sheets of ice on floor of freezer, and ice maker doesn’t work. Looks like it’s the norm for these. Please post if you have spoken with an attorney. If no one has, I am going to.

Im totally done with the Maytag brand that Ive trusted for over 30 years. I never knew until yesterday via Facebook friends that they are not true Maytag-made anymore. They were bought out by Whirlpool eight years ago. I bought my top-load Maytag Bravo 400 Series Washer ($1,028) at Home Depot in October 2008. No problems with it until now, less than 4 years old with error code DL. So I looked in the book and found it was the lid lock (the little red light wasnt lighting up when closing the lid, which prevents it from running).I made an online appointment with Sears Home Appliance repair to check it out. But after talking with online friends and googling fix videos, I was able to get it running today by taking the top off, unplugging the lid wire and plugging it back in. So far, its working but now I will fear each time I go to use it that something else will fail. My old Maytags (washer and dryer) bought in the 80s never needed service until they approached the 14- to 15-year mark. That only tells me that the newer made appliances are total junk! So many complaints and how the companies dont back their appliances, it just sickens me.

When we turn up the temp in the oven above 400 degrees, noxious fumes come out giving us headaches and nausea. We have to open all the doors and windows and bring extra fans...very toxic. PLUS the vent for the oven is at the top of the oven door, so the knobs for the burners get so hot you cant touch them!

Recently started having puddles of water on floor every morning. Just noticed a thick sheet of ice on freezer floor when I had trouble closing the freezer door. Also the water dispenses very slowly. Removed filter and it would not dispense at all. Will try melting the sheet of ice to see if that helps. Purchased 2011.

We are on our 2nd Maytag washer with the 1st being a top load with agitator and the second without. Both were also bought used. The 1st one broke after I was cleaning it so totally my fault but the second one the door lock broke. Aside from that they do wash clothes well and but I do wish there were more or different cycle settings. Overall they are good machines for out price. (Being used that is.)

I purchased a Maytag dishwasher at Home Depot in October 2009. Recently, it made noises for a few months of laboring, and finally would not start.Maytag said it’s out of warranty and wanted $125 just to diagnose. Took it to my shop for $60 to diagnose and they found a faulty control panel.

Bought a Maytag top loader washer from Lowes in July 2017. Have had nothing but problems due to faulty computerized guts. Worked intermittently and took a long time to wash compared to older machine. Repairman out twice... replaced computer board and still have problems. The machine was made in Canada according to the label. Hey Canada, what is going on making junk? Too bad that we did not know beforehand what junk the Maytag brand has become. Lowes should not sell this junk to help its reputation and valued customers.

I bought a refrigerator from Home Depot in July 2013. In late November 2014, I noticed water on the floor in front of the fridge. I called the Maytag customer service and reported the problem.. The customer service rep explained to me that Maytag discovered a design flaw in the part that allows the water to drain when going through the defrost cycle. I also called Home Depot. Their response was it was my problem because the fridge was out of warranty and I did not buy an extended warranty plan. After two more calls to Maytag, they scheduled a service appointment. The service repairman told me the same thing about the design flaw. I have the old part and the package the new part was in. The two parts are completely different. I requested that Maytag or Home Depot replace the fridge or give me credit for the amount I spent. Maytag is now saying there was not a design flaw and because of that, Home Depot refuses to replace the appliance. I will never buy another Maytag product or shop at Home Depot. The extended warranty is a way to place the responsibility directly on the consumer and eliminating the responsibility of the manufacturer and the store.

I bought the quiet series 200 dishwasher about 2 years ago. The control board went out and because it was past the industry standard one-year warranty, we were told we need to pay the cost of repair and parts ourselves. Well, I came here and seen that there were numerous complaints about that board specifically with all their models of dishwashers. I called and raised hell two times, and then I found them on Facebook and publicly bashed them there on their own page. They got back to me there and gave me an email address to explain my problem with their product. So I did. I even copied this web address and pasted it to my complaint. First, they called me and offered the part at 50% off. I told them, Go to hell. Even at 50% off the part combined with the techs labor, Im still better off buying a new machine and it will not be a Maytag ever again! A week after that another phone call came from them, this time saying they will cover the part 100%, but no labor. I agreed and for about $180 I got a new control panel installed and a one-year warranty on everything except cosmetic damage. Not bad, eh? Certainly not typical, I was told by the repair guy. Be angry, be respectful, but be persistent and public! That’s my advice.

MAYTAG BRAVOS WASHER - Biggest mistake I have ever made, like all the other complaints, washer does not clean the clothes. This washer and dryer are in our vacation home. Only used on weekends we are there, now the washer is broken, will not spin and UL light comes on, even with no clothes in it. DO NOT BUY!!! Like others have stated, we need to start a class action lawsuit against Maytag for fraud and knowingly selling junk.

Washer has plenty of functions for me to was even my work clothes. These saves me money and time. Washer leaves clothes clean and you can even wash your blankets.

We had remodeled our kitchen in 2009. Bought new fridge and stove (Maytag). The oven door came off and cant get it back on. No matter how many times we tried, no way can we get it back on. I had to have my son to come and help us. No sooner did we use the handle to open the door off again. This has been going on for 3 years. **, well fed up. I called Maytag about this issue and they told me they would get a repair at my cost. The fridge freezes all the produce, cant regulate the temperature. Never ever will we buy any Maytag product again. Who knows what’s going to happen next? Oh, and the paint is chipping off of the grates of the gas stove.

Washer was purchased at Lowes under direction from staff... Great washer, environmentally better, less water consumption... Well washer is piece of crap. Activator is out, door stays locked, have to unplug to release every time used, water does not drain and cycles do not function or start. Lowes no longer carries product and all other review on spot as to cost to repair... Piece of crap, loss of $600.00+. Could be used as target practice, best case scenario.

Electronic control board fried after 3 yrs on Maytag Gemini range - certain buttons on control board would not set for ovens. Called Maytag, said was not covered, past 1 year warranty. Recommended repair shops, all overpriced. The piece cost between $300-500 for a 3 year old stove. Cheapest repairman wanted 90 to install piece. Ordered piece online and replaced it myself with help from YouTube video. Maytag has lousy repair records lately. Of 4 Maytag appliances purchased in 3 yr kitchen remodeling… already had issues with 3 of them. Do not recommend Maytag anymore!

I purchased all new appliances and decided to go with Maytag. My Maytag Refrigerator model MFI2569VEM after 12 months, just after the warranty expired, started leaking all over my kitchen floor. I called Maytag and all they told me was there is no recall on this model and there was nothing they could tell me over the phone. I purchased an extended warranty and that is a whole other problem to get someone out. They said to check the freezer problem I need to call when the leak was occurring, so they could see what is happening. So basically, I need to leave water on my kitchen floor so they could see what is happening. Who hires these people?

We moved into a new house and the GE washer died after the first week, then the Whirlpool replacement died after two weeks. Decided to try the Maytag which the store gave us for $50 more than the Whirlpool. It runs like a champ. At least two loads of laundry a day every day and sometimes weekends. Clothes come out perfect, no damage and the machine is quiet.

CONSUMER BEWARE! The Maytag Bravos X is without equal the biggest disappointment I have ever had the frustration of using. What a rip off! Water goes in, water goes out and it makes A LOT of noise. That’s it! (That locking lid should have been our first clue.) Specifically, a normal load takes one hour. What you save in water you pay double for in electricity. If you place a folded pair of pants in the washer that’s the way they come out; folded. Two twin sheets and a small blanket come out of the washer with dry spots every single time. If I use liquid fabric softener the clothes come out spotted with it. And it is louder than the train. You would be 100x better off purchasing a washer at a yard sale for $25 than to throw your money away on the Maytag Bravos X. DON’T DO IT.

Come on people are you serious! Im talking about all those people who give this washer great reviews or even mediocre reviews. This washing machine sucks! Thank God for the glass lid so you can see how terrible it washes. No water in this thing. Clothes that sit on the edge of the bowl do not agitate enough to be washed if there was water in the wash cycle. Bleach that you use in your white wash cycle is left over and gets onto your colored cycle if you wash it the color cycle next. I ** you not, mark my words that stains are left on clothes even in a cycle that has lots of water in it. If you think Im high or crazy take a look at your local Home Depot or Lowes store. Check the area for washing machines that are for sale that have been used. You will find this Maytag Bravos XL machine there. They look good and are practically brand new and they will be there for weeks on and because people return them if they get lucky to return them. I called my store and they refuse to take it back and told me to call the manufacturer. I did just that... I called the manufacturer and they told me they can send out a serviceman to check the washing machine. Butt...and a big butt, if they find nothing wrong with the washing machine that I will be charged a service fee. Bunch of **! For all of us that get stuck with this pile of garbage we can thank the tree huggers for trying to save the world with low water consumption water washing machines.

Oven racks falling down and theres appears to be no solution because the interior liner of the oven has warped. The 3rd party repair guys tell me the interior liner needs to be replaced, its not worth the repair cost, Im better off shopping for a new set. Its so unfortunately that this happened (we moved into this house with existing appliances that we cannot use...) and it seems to be a common problem, yet Maytag claims they have NOT received any complaints about this.