This washer has no agitator post and doesnt seem to clean as well as ones with agitator posts. I have heard that they are easier on your clothes though. The dryer works well enough, but I believe the control panel/motherboard needs replacing. The signal sounds even with the dryer turned off, which is startling to my dog and me. I reset it by flipping off the 220 breaker in the garage and leaving it off until the next time I do laundry!

No problem with retailer. Problem is this top of the line Maytag dishwasher, Model# MD8895lAWW. Stinks all around. Takes long to wash and load, times are far apart and too few so holds few dishes. Dishes and glasses break because of the tine spaces. Horrible dishwasher for high price. I hate it so much it upsets me daily. All I get is a sorry from Maytag. Its not that old, only a year and a half. Why no satisfaction? I will avoid all Maytag products for life.

My wife and I bought a Maytag Bravos at the suggestion of a store employee at Lowes. Since we have owned it, I have seen the reviews and the washer has been a total let down. We have experienced all the same complaints. Loud noise, door lock not working, not enough water in the drum to wash clothes, and the bearings going out and it doesnt work. NEVER will we buy a MAYTAG again. To the scrap yard I go today. Thanks MAYTAG for wasting my money. Thanks LOWES for recommending this garbage.

Bravos XL Like so many others Ive read, this is a terrible product. Washer constantly goes off on unbalanced load. After 14 months, the plastic tub disintegrated. Maytag tried to sell me the service and extend a warranty for $300 also. Just like all the other reviews. Wow, has Maytag gone downhill.

After only 3 yrs of normal 2 person family use my Maytag washing machine completely failed. The ball bearings in the transmission seized requiring the replacement of the transmission. At the same time the control panel failed yielding the machine completely unusable. The repair cost was more than originally payed for the machine, forcing me to purchase a new one (not a Maytag). Maytag said since there was no recall on this model that they could not help me. I bought the Maytag because of their claim of quality. This was not my experience either with the product, or the customer service.

My fiance bought this dishwasher 5 years ago but has never been able to use it due to the fact he is disabled and unable to open the door. When I moved in 4 months ago, I began using it regularly 2-3 times a week. Yesterday, I loaded it and when I hit the start button, it did nothing. The lights come on but the start button doesnt seem to be working. I have torn it apart twice and after looking all over the internet have determined that the control panel is bad. We live on a very fixed income and fixing something like this will take a large part of our budget. I am shocked that something so expensive can only last a few months then stop with no warning. We will be calling and adding our names to the list for the class action lawsuit here in California.

I do not have a problem with Lowes; the problem is this crummy washer. Any digital anything is only as good as its programmer, and it seems that all digital stuff suffers from the same malady. I long for the old top loader I had 30 years ago. It actually did get the clothes cleaner and they did not smell after being washed. Plus, I could customize each load just exactly the way I wanted to with the knobs and dials. This Maytag goes to Error when adding water because I have an old well which does not supply enough water fast enough for the way it was programmed. I have to fill two two-gallon buckets and carry them to the laundry room and pour them into the washer. Every time. Hot, cold, or warm, it doesnt matter. And I, too, have to pre-wash some dirtier items. The old gasoline Maytag did a better job than this one. And this is progress!!!

We have had a Maytag Bravos washer for a while, which has a see-through top load lid and a very small or low agitator. I have to say that I really miss the old fashioned agitator which makes all the clothes being dragged underwater and scrubbed well. We have watched the loads being washed in this washer many times and the clothes are not being swished around very effectively. You feel like you need to help it getting the clothes washed as it seem like it just sit in the same place throughout the cycle. The clothes ends up in big knots around the edges, and you can see the same towel sitting on the top during the 2-minute rinse cycle, never getting completely under water. During the wash cycle, the lid gets locked, so you are not able to open it up to untangle or move towels around if it has gotten unevenly distributed. The wash cycle is very quick, so all in all, Im not sure how clean the laundry really is when its done. We will never buy this kind of washer again.

My husband and I purchased the Bravos XL washer and dryer set about a year ago as our first big washer/dryer purchase for our new home. We spent about $1200 on the set from Home Depot. I very much regret this purchase as the washer never gets our clothing clean! The washer never puts enough water in the basin and the clothing comes out with strange white smudges EVERY. SINGLE. TIME.I have tried changing detergent, I have tried skipping fabric softener, Ive tried rinsing out the dispenser thinking it was residue from old soap. I dont know what it is, but what I DO know is that the clothes go in without the white smudges and come back out with them for every load. I have to run a second rinse cycle just to get it off, which means Im washing for at least an hour and a half. I DESPISE this machine and its costing me more on my water bill.Additionally, the dryer isnt much better. It constantly shuts itself off even when its not on energy saver mode, with the little red light going on for air flow. Ive checked the connection and dont see what the issue is. If I have a big load such as blankets in there, I have to dry them all individually for almost an hour just to dry my bedding! It simply wont stay on to dry a full load. I very much regret my purchase and wish Id gone with something simpler and cheaper as it would have done a much better job with my laundry. Lesson learned. Dont waste your money on Maytag.

This product has been a huge disappointment, from day one. It wrinkles and tears clothes beyond recognition. When I called Maytag to complain, they tried to up sell me a service contact. I explained that it works fine, as a shredder, but it is just a bad design and asked if Maytag had any recalls. He then told me if I purchase the service agreement and they cant fix it then they will refund the $$... ITS NOT BROKEN. It was crap when we got it home. Shame on me for not taking it right back to Best Buy. Someone needs to start a CLASS ACTION SUIT. I am sure they have duped many people into buying this shredding machine...

I purchased this set of Maytag Centennial Washer and Dryer from my local Home Depot in Dec. 2011. I havent had a repairman come out yet, but I am extremely dissatisfied with them. The washer is a problem because it doesnt seem to fill up with enough water to wash the clothes. Also if you want to add something to the washer that you forgot you stop it, and go to restart it again, and it starts removing all of your soap and water again. This is a waste of money, if you cannot stop it and start it again without it filling up again. I would not recommend anyone buying this HE washer & dryer. Also the dryer seems to heat up too hot to me.

Purchased a Maytag Bravos washing machine. DO NOT BUY THIS MACHINE. Disaster as the cycling is hit and miss. The clothes can take 4 hours or more to wash a load. And even then the clothes may still be soaking wet. Grandmas old wringer washer was better. DO NOT BUY MAYTAG. DO NOT BUY MAYTAG BRAVOS.

I have purchased my top loader Bravos washing machine 3 1/2 years ago and I have had nothing but troubles with my machine. I have had to replace the motherboard twice and I constantly have that foul smell in all our clothes. I have to wash each load twice and still the smell doesnt come out. I have also complained numerous times about the water level not being correct, but they keep saying that is how the high efficiency machine is. I can watch my load washing because we have the clear lid which I like. But at the same time, it gets me really angry seeing how this doesnt clean clothes like it should. I dont believe that the water levels are right at all. I have clothes that dont even get turned over as they are washing and I have even smaller loads than before. I can only clean 4 adult pairs of jeans at one time and I still think that is too much. I clean my machine every time the red light turns on with the Affresh tablets and sometimes I run a clean cycle with just bleach. Maytag has done nothing to try and correct these problems. Its so sad that I have to take my clothes to the laundry mat to go wash them and there I have absolutely no problems. They have the HE front loaders and they have enough water to wash my clothes and I can actually see them being washed. I will never buy a Maytag washer or dryer again. How sad you have all these complaints and no one to help you fix or correct them the right way.

I purchased a new electric oven/stove, dishwasher and over the stove microwave. My dishwasher didn’t work from installation and it took Maytag over a month and half to repair. My oven door hasn’t worked properly since purchased and finally broke and I have been without an oven for two weeks waiting on repair. The customer service does not listen to you and seem to be completely unconcerned about your problem. I was told the item broken was a common stocked item and the repair would be quick but that was not true. The repairman told me they would have my parts in a week and would install them on a Monday. They have now scheduled my repair for Thursday. Over two weeks with no working oven. I will never purchase a Maytag appliance of any kind due to the terrible customer service.

Front load washer is four years old. Approximately two years after owning the washing machine it started burning and ripping our clothes. Maytag sent someone out to repair at no cost. The problem stopped. However, approximately two years later it is happening all over again. Thus, there is either a deficiency in the Maytag product or the repair has failed. Maytag will only repair at our cost. True, the washer is four years old but the same problem keeps happening. Plus, that is not a long time in the life of a washing machine. The customer should not be held responsible for a recurring problem with their product. The front load washer and dryer were very expensive. We will NEVER buy Maytag and we will continue to share our disappointment to whoever will listen. It is shameful that Maytag says they stand by their product but when its put to the test Maytag completely fail. Double thumbs down for Maytag and customer service!!!

My Maytag washing machine is rusting out at less than three years! [Photos included]. I have called customer service twice, spoken to two different women and have been told that it is a cosmetic issue [Model MTW2541240; Serial CW2541240 ]. The last e-mail with photos was sent to Gwendolyn **. I indicated that the rust has ruined very expensive sheets, other clothing, towels. It took me a long time to figure out what was causing the spots on the clothes. There is rust on the outside of the machine, the lid and inside the actual drum which holds the water. The machine is a lemon. You have me registered in your system with the date of purchase.My question to you, since when is rust in the inside of a washing machine a cosmetic issue? Are you aware of this issue? Do you as the CEO believe this is what is acceptable for a Maytag washing machine? I firmly suspect this issue is beyond my washer based on my research with various stores and sales people. They are telling me I am not the first with this issue, non-Lowes stores. I purchased the machine at Lowes and because no one at Whirlpool was responsive to him or to Lowes, he is offering to apply the refund to a new Lowes washing machine. I am now in the process of searching my credit card records from Sept-Oct 2008 which is when I bought the machine.I would like not to be restricted to Lowes for another washing machine. I will notify Rick ** (at the Lowes Turtle Creek, Coconut Creek store in Florida, telephone 954 346-3993) of this letter to you so that you and Rick dont think I am trying to obtain a double refund. I just want the full value of the washer back so that I will have a choice in the replacement. The selection at Lowes is limiting. I will upgrade to more of a commercial washer and pay the difference. I wanted you to be made aware of this issue.

Do not buy a Maytag Washer. I had a Maytag for 25 yrs with only 1 repair in its 23rd yr. When it finally retired at age 25, we replaced it with another Maytag assuming it would also last long. No chance. We had only 2 good yrs. Now, at 2 yrs old, it is so so loud during the spin cycle that it sounds like an airplane (757) is flying overhead at 50 ft above the roof... No way can we possibly use the washer if anyone in the house is sleeping. Repairs cost more than the initial price of the washer. Please do yourself a huge favor and buy another brand. There are too many complaints about Maytag to even consider purchasing one. Not worth the aggravation!!

Washer broke down after one year. The washer stop in the spin cycle. Called many times - got no satisfaction. Still using local laundry mat. Very disappointed. Always thought Maytag was top of the line. I guess I was wrong.

Purchased a new Maytag washer from a local Hardware store chain. Waited 3 days for delivery. Old washer was hauled away. Started using new Maytag Centurion the same night it was received. There was a funny odor coming from the washer that was discounted as new equipment smell. Saturday the Maytag Centurion washer was leaking some odd lubricant that had the same odor as the mentioned new equipment smell. Since this lube had been leaking out in close proximity as the liquid detergent my wife used a towel to clean it up. This towel went into the laundry with other clothes.Now Im concerned that whatever this oily stuff is, it’s in all of the clothing that was washed with the towel. Since I live on the West Coast and Maytag only answers the phone during the week Eastern Daylight Time I will call (2 days) after the fact. You might do well by finding out what this lube stuff is before you take it home and how youll have to deal with it once it leaks.

I purchased a Maytag Dishwasher at $600. 6 months after installation, the control panel quit. Maytag sent a repairman and replaced the panel. 4 months later, the control panel quit again. The repair man told me that if it failed a third time, that Maytag would replace the dishwasher all together. The control panel quit again just a few days before the warranty expired. When the Maytag repairman came for the repair, he tried to convince me that it was not the control panel this time. He then replaced the control panel, but did not use the embedded electrical connectors. He literally cut the wires and wired it together by hand, wrapping everything in electrical tape. He said this was a different repair than the others and the three strikes and a full replacement rule didnt apply. I wasnt convinced and called Maytag to complain. I was promised a six month warranty extension, if I would accept the repairs. Two months later and the control panel has quit again. When I complained to Maytag, I was told that I had no six-month warranty extension and it had never been promised to me. They offered to send a repairman to diagnose the problem for $130. Needless to say, there will NEVER, and I repeat NEVER, be another Maytag appliance bought for my home.

I had no issues with my washer. The best thing I ever did was stop using Sabrina softener in it and made the switch to vinegar. The worst thing I ever did was think that paying $900+ for a nice washer would get me more than a year! What a joke! I started noticing small leaks when my hardwood floors started lifting and once my husband looked into this, we realized there is no seal around the top of the drum. So there is no barrier between the drum and your floors basically. Then one day we had a flood. As we watched the cycle run, we noticed that when the water was filling into the bleach and fabric softener compartments it was coming in at such a high rate, it was spilling over the sides down to the floor. So we went to the internet and found a few complaints about this, but no answers. Thankfully we found one guy who had the exact same problem and even had pictures that matched ours. Luckily a real appliance tech answered him and he couldnt even figure it out but took a guess at what I might be: the water inlet valve. But that was just a guess. So we called around to find the part and talked with a few sales persons. One was so nice to even ask a technician standing in line. And he said that there was no way this could be it. But then we decided to take a gamble. We also noticed that both compartments were filling up at the same time, but the bleach should fill during the wash cycle and the fabric softener during the rinse cycle. So it was either the $104 water inlet valve. Or the $200+ circuit board. These are my options after already spending $900+.. So we went with the valve and thank goodness it worked!!!! It is so disappointing that after a short time, this washer broke and cause more damage to my floors. It is an awful design. I bought myself the nicest front loaders for my first house. When that broke 7 years later, I bought this washer because I liked the no agitator design without the smell of a front loader. Now when this one breaks again, Im not buying another HE machine. The majority of people I talked with today said that these HE machines are breaking down faster and faster as the get better and better. I am so beyond disappointed, angry and in shock that this washer failed in less than a year and a half time. My hope is that this review will give the answers we couldnt find without paying an arm and a leg. Is this what passes for quality these days???

WARNING FIRE/HEALTH HAZARD - BRAVOS MVWX500XW1. Purchased it new 2011. Never cleaned well. Some clothes came out with dry spots, darks had soap scum/lint spots over them. On several occasions, clothes were not wrung out properly. BUT when I went to do a load of laundry recently, I heard a loud POP and almost instantly my entire basement filled with an acrid, dense grey smoke coming from under the machine. I am concerned toxic chemicals were released. People still smell the odor in the house. Need to get in touch with company again after the weekend to see what they will suggest.

I have had 2 Geminis. The first one was fine, this second one is a mess. I have had at least half a dozen parts replaced. I have insurance to have this oven repaired but have paid to have the window seal replaced on at least 3 occasions. The top of the oven is so hot that when I have used the burners to cook on top I have received 2nd degree burns. I have received burns on several occasions. I asked dealer if I could trade this in but said I would have to sell it on my own. I would not subject this oven to another person as I feel it is very dangerous.

I have bought a new Home Depot Maytag Impeller HE washer. After 6 repeat washings of 2 items that are lightweight dark brown it was obvious after drying they had soap and lint and lot hairs on it. I reached with no he detergent. The last 4 times the water level filled to 1 depth even for high level water setting to extra rinse or power wash settings. I went to Home Depot and they suggested I call Maytag repair center on Tuesday after the labor day holiday to have them check it out. I will also call the supervisor at Home Depot as I do not feel paying $600 for a faulty machine is acceptable.

I bought a Maytag refrigerator model MBB1953XEW three weeks ago. According to its features on the Maytag website, its supposed to be quiet (QuietSeries 100 sound package). Ha ha, make me laugh. Its the noisiest refrigerator Ive ever had. The repair guy checked it out this morning. He spent about 5 minutes running some sort of test with the help of his iPad. He then told me everything was perfectly alright, the noise was normal for a Maytag, and that I was going to get used to it.Needless to say, he had a totally condescending attitude. Its the first time I ever bought a Maytag. Previously, I had a General Electric that was noisy but not as much as the new Maytag. Prior to that, I had a good old Kenmore that was perfectly alright but that I had to give away for other reasons. This time I chose Maytag because I thought it was good quality and I wanted it to be very quiet. Well, nope. Next time, for sure, it wont be a Maytag.

I bought a front loading Maytag Cloths washer model# MHW3505FW1, SER# C71451407 new in April 2017, from Home Depot, since then it has broken down three times, with a water pump, a master board, and now another master board, we were told by the appliance repair service that is used by Home Depot extended warranty service, that it will take a month to receive the master board. Thats it... Never again will we buy another Maytag or Whirlpool product. This is unacceptable. Gone are the years when Whirlpool and Maytag made quality products!

We just purchased a house with new appliances. They are Maytag. When I use my stove the oven heats. I have no idea why. I wondered if anyone else has had this problem. When I turn it off it turned off but it turns back on when the oven is on.

We purchased a MDB8949SAW dishwasher in 2013. 1 month after the warranty expired the touch buttons went on it. If you selected normal it would opt for something else like rinse only. We researched online and my husband followed instruction online to take the door off and seal the moisture to prevent this from happening. This worked for about 2 months and now back to the same thing. We paid $500 for this and just living with the problem for now. All we can do is warn others.

I have had the set of Maytag Bravos for about 5 years now. In the 3rd year, the bearings went out. Just recently, leaking water pump. This washer easily eats clothing. I have to disassemble every so often just to get the missing socks etc. out. The only good thing, Maytag should be ashamed I know this, is that the machine is easy to fix. I imagine since they made it so cheaply. Really nothing to the machine.

Electric stove range is great. It was very affordable, this stove is very easy to clean and wipe down on the outside. I had it for 4 years and had no problem with it. Would definitely recommend it to anyone on a budget. It also has a warranty which is also a plus.

Worst brand ever. They both broke at the same time. Spend too much money. Never buying these brand again. Maytag sucks. Dont buy Maytag washers or dryers.

Disturbing that this product made it into production. I have the matching dryer too, and its just as bad. First the washer rolls up clothes into a tight ball better than I could do if I did it by hand. Then it spins, setting the wrinkles in thoroughly. Then, even though I shake out the clothes before putting in dryer, after the clothes come out of the dryer (without letting them sit in there) - the clothes look like someone drove over them with a car while they were rolled up in a ball. Bonus: the clothes dont even get dried. Ive watched the clothes in the dryer, the drum is designed so the clothes stick to the outside of it and go around, they never actually tumble or get any air circulation. What a disastrous product.

I purchased Maytag gas range in March 2011 at Home Depot, Model No. MGR5605WWO. I received the product in May 2011. The porcelain on the grates chips away leaving large grooves in grate, which affects cooking efficiency, (the fire burns erratically). First, I called 1-800-688-9900. The grates were replaced. And then same problem, it was replaced again, and again the same problem. The warranty to cover stove was extended by 6 months. The enamel on the round magnetic cover for the burner is also chipping away. I was told that this chipping of the enamel is a cosmetic problem and does not affect the functionality of the stove problem.A repair technician was sent out at my request to see firsthand the problem grates. I was told by him that if it occurred again, the manufacturer needs to be made aware of the defective grates. He noted that the enamel covering on the grates was not uniform. I have been told by Maytag supervisor today that she will get back to me within 3-5 days and let me know what is going to be done. I have had gas ranges before, but this is the first time this problem has occurred and its continuation is unacceptable. Is there anything further I can do to ensure I have stove grates that do not chip continuously?

Maytag top load washer. I dont understand why Maytag would make such a piece of crap. It takes so long to wash, that I can only wash a couple of loads a day. It doesnt fill. It doesnt get the clothes clean. My electric bill is higher. Its so noisy too. Never thought Maytag would make such garbage.

Same as everyone else, ice freezes up on the bottom and water runs out all over the floor, ruining my new floor. Whole kitchen was new including all appliances. Maytag is ruining my floors. Can find no drain pipes so not sure where the water is supposed to do. I think they forgot to install one. But I am getting pretty sick of seeing my floors ruined and stepping in water.

Bought a new home in July of 2016 and the builder had included a Maytag Bravos XL washer and dryer. They are THE WORST performing appliances I have ever used! I will replace as soon as I have the means to do so. DO NOT PURCHASE the Maytag Bravos XL appliances. The engineers that designed them should be fired! The washing machine makes an incredibly loud noise (like an old starter grinding in a 50s car). Im told that this is normal for the machine. Does NOT clean well and leaves soap spots on dark clothes... leaves them on light clothes but I cannot see them. Whites come out dingy even with bleach. The tub is so deep that I have to use tongs to get out smaller items, I am 53 tall and have never had this issue before. Soap dispenser drawer wont stay closed during wash cycle. Clothes are so badly tangled during the wash cycle that it is hard to describe the wrinkled mess that has to go into the dryer.Dryer issues: Very loud. Very wobbly and unstable, and yes, it has been leveled 3 times. Bed linens have to be separated at least 3 times during the drying cycles because they twist and wad up into big, wet knots of cloth. Infuriating!!! Dry time is very long unless you wish to cook your clothes. So disappointed in this product. Total rubbish!!

Has had problems with machine being off-balance and clothes getting clean. 3 years and now the machine is broken. Too costly to get repaired. Warranty only covers very specific things. Have had Maytags repair person come out and he did not access the problem properly. What a waste of time and money! Says it needs a very expensive part which with labor and parts cost almost as much as machine.

I saved for this refrigerator for some time and assumed at my age this would be my last one. Thats a joke, less than 2 years and I see this water leaking on my floor. I blamed my dog at first. This was a Home Depot purchase. I love the middle drawer but the freezer has this problem. I removed the ice but it comes back. I did not purchase the extended warranty because if you have an excellent product, you dont need an extended warranty. And of course this happened RIGHT AFTER the warranty ran out. I am VERY upset with Maytag/Whirlpool. Will NEVER buy another product from them. This fridge should not have problems in less than 2 years.

I purchased a front load washer over 2 year ago and the bearing on it has gone bad. Maytag jumped at offering to ship the parts to me at no cost (which at the time I thought was great). I waited 3 months to finally get the part, because it was on back order, and now was just hit with the labor bill! If I would have known a brand new washer was going to go bad after 2 years and cost me over $500 to repair, I would have gone with another brand, In fact, I will never buy a Maytag or Whirlpool. I will ensure that I tell everyone and post comments all over the website about how ** of a product Maytag/Whirlpool produces. Companies like these give the U.S. a bad name! Maytag, you suck!

I have been the latest victim in purchasing a Maytag Refrigerator. Something needs to be done about the defective products they are putting on the market. I received 9/7/13 (yesterday) a new Model FW: 555 Complaints and Reviews about Maytag Refrigerators bottom freezer refrigerator. After being plugged in for 3 hrs, the temp was 60 degrees.. After 8 hrs same and 24 hrs same. I lost everything because of the defect. I notified the store 3 hrs after purchasing it and because I had it delivered on a Saturday I have to wait till Monday to get this resolved. I want everyone to read before buying a Maytag product.

French door refrigerator w/ freezer in bottom 2 years old. Purchased this model MFI2665XEM7 December 2012. June 2014 had repairs to freezer. Freezer froze up and bulb stopped working. Maytag covered repairs. September 2014 the ice maker stopped working and having it replaced as we speak. Total cost today for ice maker replacement $216.18. Am I POd, hell yes!!!!!!!!!!!!

I bought Maytag frost-free refrigerator last August 2006. But now, I noticed that ice builds up in the freezer. The product is only five years old but I was told by Whirlpool that they had discontinued making defrost heater. The reason why I bought Maytag was the ad on TV showing the Maytag service technician seating and doing nothing, implying that Maytag brand is a good product. Think again before buying Maytag products.

This machine doesnt wash your clothes. It leaves them dry & the agitator sucks too. I am so annoyed. I just bought them & had them delivered 7/27/15. It has only been a few days & NOT satisfied. Overpriced over $800 for it & its crap! Same with the Bravo dryer, it takes forever to dry. I wish I still had my old washer & dryer (had them for 7 years, NO problems). Very unsatisfied. DONT buy these, they are total CRAP!

I bought a Maytag refrigerator, model MBF 2256 KEQ2, two and a half years ago. Now the cooling coils are freezing up. I checked heater and thermostat for continuity and they were okay so the only thing left was the timer control circuit. On the earlier models, the timer control circuit is controlled by a Timer Motor or an Adaptive Defrost Timer which is separate from the main Electronic Control Board and much less expensive. On later models (including mine), the timer control circuit is incorporated into the main Electronic Control Board so if your automatic defrost quits working, more than likely you will have to replace the main board. I did not purchase an extended warranty because I believe they are useless from past experience. I bought the part on Amazon.com, received it in four days and replaced it myself for a cost of $78. This part costs $110 to $118 at Sears or a Maytag dealer.

I have only had this machine a few months and am completely dissatisfied. It sounds like a jet taking off and uses so little water. The clothing does not come clean and wrinkles are close to impossible to iron out.

I purchased a new Maytag washer (Model# MVWC565FWO) from LOWES 18 months ago and the paint is bubbling on the inside of the door. Neither Lowes nor Maytag would do a thing. We have spend many $1000s at Lowes and considering the replacement cost is only $126 for a new door I can see Lowes following Sears for their lack of customer service and diplomacy in matters like these.

Maytag dishwasher mdb7749awm2 - It appears that everybody who bought one of these dishwashers has run into this issue at one time or another, and it usually takes one full year of use before the control panel goes out on these units, and in most cases, it has to do with moisture getting on the thin strip of wires leading from the control board to the control panel. It usually occurs right where the strip enters the control panel... There is nice little gap for moisture to rest right on the wires, which will eventually lead to corrosion. I included an image of what to look for (see the nice black rust areas on the wires? That was my problem, and probably yours, too). If you have some very, very fine sandpaper, and have patience, then you can get the rust off the wire, but be very, very careful, or you could take the small thin wire off in the process! Ive made this repair myself to my unit, and I did it for one my friends machines (it was a Maytag, and his lasted two years, but had the same problem, too), and both had similar problems and right in the same spot! After removing the corrosion, the system worked great again. However, before hooking the unit up again, I sealed the area with some silicone to hopefully prevent this from happening again. Now, Im not saying that this is the problem that you are having, but its worth investigating, and dont be afraid to pull-off the front panel...its just held on with an adhesive and will go back on with no issues. Anyway, this could save one hundreds of dollars in repair costs. I hope that this helps.

When we first purchased our fridge, I was super excited. I have read the numerous reviews regarding ice in the bottom and the noise. Ours is noisy also. Nothing I cant live with. Now ice on the bottom. That doesnt work for me. A friend of ours told us the drain was plugged. Not that the doors needed to be replaced, nor does it need gaskets. All you need is a hair dryer and a man like mine who can build or fix anything (honest to God that is the truth). He took the drawers out and then removed the door to the freezer. In the center on the back of the fridge is a drain hole. Aim a hair dryer in this spot and it will melt the ice which is plugging the drain. Ours took about three years to have the water in the bottom issue. Since we have now seen where the drain hole is, there would be no need to take the door off and the drawers out. Now, one other preventive measure. Take off the lower back plate of the fridge. At the beginning of the drain hose is a rubber nipple. There is barely any room for the water to drain. We cut the end of the nipple off in order to make the water drain better and less likely to stop up. We just snipped a bit of the end. The reason it is designed like that is to prevent air from coming into the. Just a small snip. I hope this may help some of you. Tell the Maytag repairmen how to fix it.

Purchased this maytag oven from home depot November 2011. Oven has been working properly since install. The top burner controls do operate too easy and you can just brush up against the stove and turn the gas on which I seen here was mentioned. My major issue is the stainless steel finish that was applied. It appears that this metal was not properly prepared prior to applying the finish. The oven door is with rust blisters. The metal under the coating is causing this problem. The finish in the other areas is with no problems... No chemicals have been used to clean this oven.Customer service of maytag stated that this stove only has a one year warranty... so if you buy any maytag just remember one year and when it breaks down the cost to fix will be more than a new defective maytag stove. I will not purchase another maytag product and I do not recommend that this manufacturer be considered when purchasing any appliance.

At 14 months old Main computer box failed, caused the machine to shut down on unbalanced load ($400). At 28 months old Main computer box failed, caused the machine to shut down on unbalanced load. In addition when the service guy was underneath the machine to change the module he noticed the stator housing to the motor was falling off. He said he never saw anything like it. After reading about all the problems people have with these machines I have talked friends and relatives out of making the same mistake of buying an old and trusted brand like Maytag. .

I bought a full kitchen of Maytag appliances when I bought a new house in 2009. I thought it was a reliable company. Id always gone with GE before. I couldnt get the packing sticker off the oven after trying everything to remove it, so the oven bottom is virtually ruined. The timer on the oven dings once and stops; dinner burns if Im not right there to hear it. I was told by customer service thats the way it works, so I had to buy a separate timer. I am now replacing my 2 ½-year-old dishwasher because the control panel has once again stopped working. It cost me $275 to fix the first time and it lasted less than 3 months. I will never buy Maytag again! I got over 20 years of service from my GE appliances.

I totally understand the technology age. We need to move forward as a country and keep up with modern technology. But somebody please tell me why this means companies have the right to not stand by their products? Why do consumers have to pay the price for bad products and companies leaving us high & dry? My husband & I were excited to redo our kitchen. We bought all new appliances in November 2011 - all Maytag. In December 2012 (13 months after we bought them), we started having issues with the oven. The oven would not maintain the proper temperature. We called a service man in January 2013. He deduced it was the computer board so he replaced it. Cost to us - $350 (including service call and labor). Now, less than 2 months later, the same problem. Maytag, Whirlpool, Kenmore - whatever company you are now - rest assured, you will not survive if you continue to produce shoddy products and refuse to back them up. The service man is to stop by again tomorrow. I refuse to keep plugging money into a product only 15 months old. I will not buy another product from you again. I just hope the dishwasher, microwave and fridge make it to at least 5 years old. Isnt this funny? My grandma has a Maytag washer & dryer - 35 years old. You sure cant say positive things about your products today. Good luck to your future - youll need it.

I purchased a Maytag energy efficient dishwasher in June of 2010 along with an extended warranty that I keep extending. Cost $ but needed. Issue: Sensor in Panel fails so far every year and needs to be replaced. The repair technician showed me the sensor strip and indicated that this has been a big problem. (At least I have a warranty; however, it is a big pain to have to schedule a service repair person to fix the problem.) Repair (Sears) is EXCELLENT with great customer service. I did contact Maytag and there has been no recall.I own other Maytag appliances such as a washing machine and refrigerator with no issues there. In any case, I needed to replace my clothes dryer and did not select a Maytag. I purchased a GE very simple product with no sensor/bells and whistles. Not sure if I will go back to Maytag in the future - depends upon how they handle problems with their appliances. I would rather pay extra money for quality, durability, and reliability than go through the inconvenience from parts that are not made well enough to hold up.

When we moved to a new home, we upgraded all the appliances, including the microwave. This was four years ago. When the first microwave stopped heating the food after two years, we thought it was a fluke and bought a brand new one, since fixing it would have cost more. Well, I should have gone with another brand. This is two Maytag microwave ovens in four years! We cannot believe that a company who enjoys such a good reputation can get away with such shoddy products!

Just replaced a washer that lasted over 7 years thru 3 renters with the Bravos top loading washer. There is nothing efficient about a cycle to take 73 mins to wash 20 articles of clothing (t-shirts, socks and underwear). The machine dont wash the top of the load. Also the deep clean feature isnt deep cleaning. I recorded a video of 20 mins of the machine not washing properly before going into rinse cycle. If this item dont produce refunds of the amount of water wasted RE-WASHING and electricity because it doesnt clean on first wash, then its time for Maytag to pay my utilities. For the money spent on the machine, going to the laundromat every other week with 1 roll of quarters each trip comes to be I can wash for 4 years and will outlast the longevity of the machine before it breaks! Also bulky mode is how you get more water in the machine but will take 63 mins to wash.

Bought a MDB7601AWW, and then replaced front panel to stainless. Configuration options are great (can’t find better at cost up to $1,200.00)! I haven’t had an issue with any stains on non-stainless tub. Problem is now control panel failing for second time. After 1st time, sealed all connections in silicone to prevent steam from affecting it, as recommended on DIY video. I just replaced the door latch, thinking that may solve it, but hard to troubleshoot without any indicator lights. This second failure (2 yrs later) shows no indication that steam or water caused it. It does start now, stuck on heavy wash, heated dry, sanitize - per top lights. Front lights totally out. Debating whether to buy a new dishwasher ($$$) and give up super config (hard to find fold-down tines and fold-down small shelves on upper and lower racks, clips for small items, and basket that can be changed, placed anywhere) or spend at least $162 for the panel AGAIN and hope I get another 2 years from that while trusting that some other element doesn’t go out. I believe Maytag should, at minimum, make the panel reasonably priced by offering a rebate, since the part is not sold directly through them. Obviously this problem is a design flaw. I am the only one in the house, so the dishwasher is not under heavy use. At least I found how to replace it myself on YouTube, though it requires the door to be completely taken apart and would be easier with an extra set of hands and a younger back. Hard decision since it seems newer, expensive appliances have problems as well. If I buy new, I will not hesitate to get an extended warranty (1st time ever).

One baffle broke off in my washer. Very disappointed in this Maytag Model #MHWE201YW00 Serial #HL20102420. I purchased this in Sept 2012. Where the baffle was hooked on had sharp fins sticking out that ruined my 2 small rugs - shredded them.

Bought a Maytag Front Load MHW6000AW washer and had a problem with amount of water in wash cycle. Dealer sent service men 3 times and changed several parts but washer still did not work and both repairmen said they did not know what was wrong. They called Maytag Tech Support but those people did not listen and said if no code shows up the machine is operating properly. Maytag then sent another company repairman. He worked 2 hours and said he could not find the trouble and Maytag support hung up on him. Maytag then sent another company repairman and he did one test and said the machine is fine and left in about 15 minutes total time. Now Maytag refuses to send another company for another opinion but I have a $1200 machine that still does not work properly. I am totally dissatisfied with Maytag and will stay away from their products totally. Companies wonder why people buy foreign equipment and this is the answer. I had a Samsung washer and never had one bit of trouble with it.

Our brand new Maytag front loader has a optimum (LOL) soap dispenser that can supposedly wash several loads before refilling. BUT, the dispenser fills with water after one load and dilutes whatever soap is left! We talked to a authorized tech who said it was a poor design. That the unit wasnt sealed from water or it would be under vacuum. We called Maytag and they said something like, Um well it has sensors!! Did they explain how it would sense the diluted soap concentration? Nope. It should be replaced by MAYTAG! Knowing it is something that they sell that is defective. Right out of the gate!! The engineer should be fired, the quality department heads fired too!

I have had to replace the control panel on my Maytag Dishwasher 2 times in the last 4 years I have owned it. I diagnosed the problem using the serviceman repair manual which is located on the kick plate or lower plate for panel of your dishwasher. This is not one of the dishwashers that is listed on the recall list, but it is on the dishwashers list that Maytag suggested that you buy to replace your dishwasher that is on the recall list. Model number mdbh9898awb3.

We had perfectly working 20 year old top loading white Whirlpools w/ an agitator, when we remodeled our home and wanted new pretty grey appliances and decided to donate our machines to the church. I chose Maytag top loading due to their former reputation we experienced with dishwashers, etc. It had an agitator, deep fill option, extra rinse, etc. The sales person at Home Depot stated, the agitator is because people like you still want the agitator, and the deep fill will give you the water you have been used to. Not so at all!!Clothes get wound up together, even with filling the wash tub in bundles, there is almost NO water to thoroughly clean & the rinse cycle is a joke. Clothes do NOT come out clean. Im 58 yrs. old and have been doing laundry since I was 13 so I know what I am doing. Its just my husband and I now, and he is so upset that his clothes are pilling probably from rubbing together, even though I occasionally use laundry bags. I seriously wish I would have saved my money and kept the 2 perfectly working whirlpool units I had. This has been such a disappointment. I sincerely would not buy these.P.S. Weve had service out at least 5 times in the last year, and all they do is test the washer and tell us its working as intended... The last thing that is going to happen is we are going to get refunded for a different set, even though we were educated over and over what it would do by Home Depot associates. We are heartbroken. Maytag is going to lose their former reputation on these washers a dryers :( There is simply not enough water to clean or rinse things!

I have bought 2 high end top loader models (Maytag centennial commercial), brand new both from Home Depot. The problem is Maytag is making them cheaper! Suspension is coal springs that suspends the load so if you fill it up, it lowers the drum to the floor, instead of a bottom bracket that supports the weight from lowering the drum to the floor! Second is the pulley system with the belt drive that wears through the plastic casing. You know some people dont have $900 or $1,000 for a machines that says commercial or heavy duty that only last 4 years when you have a family of six! Very very sad, will never buy another Maytag.

I purchased a Maytag dishwasher for $500. After several months of it working less days than not working, I contacted the repairman. I paid $350 to replace the control panel. I wish I had just replaced it with a reliable product. 1 year into ownership and the seals on the door are falling off. May I suggest never purchasing a Maytag product?

On April 8, 2017 I was sitting in my Dining room with Dishwasher in the kitchen in cycle cleaning. All of a sudden I heard electrical sizzling and turned to see my Dishwasher was on fire. I got up and opened the door and my Husband shut off the circuit breaker for the Dishwasher. He raced to turn off water under sink and went to disconnect the dishwasher when all of a sudden hot water was shooting all over the place. I tried to catch in a bucket but it was so hot and shooting out hose fast. Kitchen and Dining room were then filled with water. He realized the turnoff under sink was installed at time of house built and cant be fixed without a lot of chopping up under cement.Well finally we cleaned up the mess with mop and towels and relieved neither one of us fell at our age. He unconnected the Dishwasher and secured outside. About 2010 there was a recall on this model Maytag. I reported it and a repair man came to change the cycle panel and said it would be fine, not. Yes almost 7 years later a fire occurred. Just glad we caught it in time without losing our lives or my house. Never, never again will I purchase a Maytag.

Although we have always had Maytags, this was the first time we purchased a front load washer. The Maytag Neptune washer smells and your clothes stink. We have purchased the most expensive laundry products, washed and rewashed clothes and have no other recourse but to buy new machines again. We will not be purchasing Maytag or Whirlpool. I would give it a minus 5 stars.

Purchased this double oven back in 2012 and have had to have the control valves replaced twice because of them jamming and snapping. The burners are undersized for cooking and it takes forever to get water to a rolling boil. The broiler in the upper oven needs constant attention when using it because food cooks unevenly and burns quickly. The lower oven is great, convection is awesome. I have seen the Maytag repairman more from my stove than I have for any of the other appliances I owe combined. Maytag should stick to appliances that only use water.

This Bravos 300 washer has never cleaned clothes adequately. I have 3 sons who are athletic and this washer does not clean sweaty or dirty clothes even with extra rinse. Now my machine is 4 years and 3 months old and it needs a new bearing which will cost me $385. The repairman said this is a common repair in this machine. Maytag should be ashamed of the poor quality of this machine. I am now looking to by a new traditional top loader. These HE machines are a joke. I am contacting them to make a complaint and see if anything can be done.

I purchased my Maytag Centennial 1 and 6 mos ago and it is already broken. The washer wont wash the clothes, just sit in the water and wont spin. I called Maytag, they offered me a warranty for another year for $371. The washer was only $550.00. When I tried to get set up with a repair service, the only company they used which was going to charge $105 just to look at it, would only take cash. When I called back to discuss with Maytag, they were no help at all. I was told they wouldnt even do the warranty since I scheduled a service even though I canceled it. I will never buy Maytag again.

I purchased a Maytag washer from Badcock. Within 7 months the control board went out. It was down for nearly 6 months. I had to use a laundromat until I finally rented one from another place. Now again months later the control board is out again (F2F3 Call Service). Due to long wait time luckily I have another warranty but am being told I have to wait 2 weeks before a tech can come look at my washer, and that they wont have a loaner or cant just get me a new washer being the problem is THE SAME! Spent hours on hold only to be told to wait AGAIN! I would NEVER recommend dealing with this company. They used to be top of the line, but clearly not anymore.

Had a Maytag washer, 3.5 tub, stopped working. The motor upper bearing lost it press, drive shaft dropped 3/4 inch and locked against lower housing, stripped out pump spline. No f/u by Maytag after many attempts. This is a design flaw, the upper housing is so thin, if it had .001 press on it I would be surprised. This flaw resulted in a cascade failure of motor and pump.

I always thought Maytag was the best, maybe because of their ad. Finally, I bought a refrigerator two months ago, which has turned into a nightmare. The company has sent a tech six times and they all say that it is a bad design which makes my vegetable drawer full of water because of moisture. And they refused to do anything about it every time (bad management). They have already spent more money on service than what I paid for the refrigerator. Figure that out.Do not buy Maytag. It was the biggest mistake I made. I also bought a washer and a dryer at the same time. I wish I could send them all back because of the ignorant people they have working for them in their complaint and service office. Anybody out there, if you want to buy an appliance, make sure it is not Maytag.

Here recently I got a bravos washer x series because it suppose to cut down water usage. Well that it did. Now going on 7 months of having it now its starting to act up like when the cycle is done it will lock again and repeat the cycle all over. I use the normal or powerwash cycle and here recently how its suppose to sense the load and then start spraying the clothes with water and detergent. Well not here. Lately it still senses and spins and then starts filling up like its on the bulky/sheet cycle but its on normal cycle and it doesnt fill all the way up - just 4 or 5 inches of water. So I dont know what is up with this piece of crap and why its acting this way. Other times it will work fine on the normal and the other cycles but now its just acting all crazy.

This fridge is a piece of crap. Bought brand new and right after warranty the freezer started freezing up and leaking all over the floor, ruined the wall behind the fridge which created mold as well as the puddle on the floor that multiple people in my home slipped and fell and it started shocking anyone who touches it. Called a repair man he says he doesnt know why its shocking probably is the manufacturers fault as well as the defect causing it to freeze up and leak. I call Maytag and the guy doesnt seem to care that my 7 year old has been shocked and says unplug it and I will just need a new fridge. I already spent the money on the new fridge. Why should I have to go buy a new one now after 2 years, that I cant afford. Its ridiculous how many other people are having problems. Its a defect and should be recalled and they should have replaced the crap fridge they sold me in the first place. You would think for such a big company they would do something but yet people are getting seriously injured and this seems like it should be taken to court for a lawsuit. I am extremely unsatisfied and wont ever buy a Maytag and will let all my family and clients through my cleaning business not to ever purchase a fridge from Maytag.

Wish there was some way to secure all dishwasher under the cabinets better. It tips forward slightly, but gets caught on counter top, so it won’t fall over. The dishwasher itself is truly amazing. I love the stainless steel inside. I ensure I use the dishwasher cleaner on hottest cycle once a month. I have no odors. Both racks hold up well and the silverware tray has never given me any problems. I even like the thin little third top rack, which is where I lay my larger flat knives or spatula. As long as I use the finish dishwasher cleaner, the dishes come out sparkling. And a few times I have forgotten to fill the finish container, the dishes still sparkle. My teenagers do the dishes a few times a week. They don’t wash them off ahead of time. On occasion I have to pick a few pieces of corn or food out of the bottom, but the dishes still sparkle and the leftover food caught on the drain, well it looks clean enough to eat. I would definitely buy it again.

Let me make it simple for you, DO NOT PURCHASE A MAYTAG/WHIRLPOOL product. Maytag/Whirlpool believes its products should work for 1 year and then become obsolete, at least this is what the Maytag/Whirlpool customer service line told me. I purchased a MVWB950YW (Bravos XL) top loader on September 4th, 2012 for $948.00 plus $99.00 for an extended warranty. The washer worked marginally well when it was brand new. June 2014, the washer in spin mode started to sound like a freight train was about to run through my house. When I called for service the service company immediately signaled it was a bad bearing and offered me $500 to put towards a new or refurbished Maytag!!! They claimed if they were to repair the machine it would VOID the extended service contract?? I wanted the washer fixed, I did not want to spend more money to buy a new machine. I continued to use the machine as is, with the incredibly loud noise. June 2015, the same machine starts to leak water and is even louder. Again the company in charge of the service contract offers money for me to put towards a new or refurbished machine. Net is, Maytag/Whirlpool engineers its products based on its warranty - 1 year. Anything after that they view as an opportunity to steal more money from you and I the consumer. Do yourself a favor and NEVER purchase a Maytag/Whirlpool product. I would like to think American products are superior to its foreign counterparts, however Maytag/Whirlpool is not in this league. In my opinion, Maytag/Whirlpool has lost the privilege to call itself American and should no longer be allowed to do business in this country.

Its about Maytag MDE7600AYW Atlantis electric dryer issues, Nov 2005 model. There is an obvious design flaw. I have replaced the automatic dryer control board twice since 2005. The unit simply never shuts off, or cooks your clothes for 2 hours. Who will recall this unit and fix the circuit? They will not admit their error.

Weve had this washer for five months now and really regret buying it. It cannot remove even minor stains and often leaves residue on clothes, even with extra rinsing. I spilled coffee on some fleece pajamas and it took four washings to get the smell out.

Im writing in reference to Model # MF12569YEM2. Bought this 3 years ago for close to 3k. Since then it forms a sheet of ice under the bottom freezer and leaks water onto the floor. It has ruined my hardwood floor and leaked through the floor to my basement and now need to re-sheetrock the ceiling. Its a bad design and should have been recalled because I see everyone else with this model is having the same issue.

We bought a Maytag refrigerator around 2 yrs ago. Ive had repair out a couple and tried to take care of this myself. I am being told by repair men that it is a design flaw that the line gets plugged and water pours out all over my floor. The refrigerator I replaced was 20 yrs old, never had a service call & never poured water all over my floor. From reviews Im reading Im not alone in this problem. Needless to say Im less than happy with Maytag at this point! Model #:MBF1953YEB3, SER. #:K22812455, reciept #:** pd 1/19/13 DECKER & SONS 430 FULLER GRAND RAPIDS MI.

I purchased a dishwasher for $741 in December 2012. I called customer service department who told me that I should expect to pay since I did not buy the extended warranty. I thought by buying a high end appliance it would last 5 years without the control panel giving out ($300 cost with installation). Please DO NOT buy this brand!!!

Just purchased/used the washer. One needs water to wash clothes. I added water to the machine just to get the clothes washed. How can this pass any reviews when it does not use enough water to clean a set of sheets? Not to mention rinsing. Does anyone wash clothes in the group that designed this machine?

We purchased the Bravos X washing machine on Feb. 9, 2012. I had a Maytag for 30 years before this one and did not have any problems. My model # is MVWX700X. I have given it sufficient time to get used to it. I have tried all cycles for my whites and am not satisfied. I use Clorox in the receptacle and I have only used Tide HE. I spot treat all of our underwear, which is changed every day, and it always comes out unacceptable. I am so disappointed since I was so fond of my old one and only thought I wanted another Maytag. At this point, I would never recommend this machine.

I also bought a Maytag refrigerator in 2013. Right after the warranty expired it was forming ice on the bottom and back of the freezer and was not making ice. I called Maytag and they told me they have no complaints on this type of refrigerator. It was also always making a lot of noise. Maytag was supposed to be the quiet one. I will never buy another Maytag product and I will do anything to make sure nobody else does either.

I bought a Maytag 4452BDW stove, the more button is not working. I did my research and was not happy to see this is a common and reoccurring issue with Maytag Stoves. The expensive of the part that too often fails again along with the cost of the service man to repair it places the Maytag as low quality at a high price. I am hoping to see a company that stands behind its product by addressing this correctly and promptly. It would be a pleasure to have my faith restored as it should be by Maytag.

13 months after installing the dishwasher, the touch pad no longer functioned. Called Maytag 800 number and they said out of warranty. I sent out repair man and he gave me a price for repair totaling approx. $300. Called back to Maytag and asked for a supervisor, she agreed to send the parts for free and I had the repair man install. Out the $120 for the repair and wonder how long it will last this time! I will consider a buying an extended warranty? Next time I will buy a lesser priced dishwasher with a dial, no more touch pads.

We were delighted with our new Maytag refrigerator, model #MBF2258XEB, until the compressor died less than a year after we bought it. Home Depot, where we purchased it, directed us to the A&E Company for service. Two weeks later, we are still without refrigeration; Maytag refuses to replace it and even refused to overnight the new compressor. We thought Maytag set an industry standard for excellence. Don’t buy this product if you want a reliable refrigerator from a company that stands behind its products.

After a year, the plastic parts of Maytag dishwasher is breaking and upstairs propeller is no longer running. Do not buy this product. I made that mistake.

We purchased our Maytag fridge on May 13, 2013. On June 19, 2013, it stopped working. We called Home Depot where we bought the fridge and they told us that we would have to deal with Maytag. What a nightmare. The repair guy came out and ordered a compressor for the fridge. 2 days later, when the compressor came in, the repair guy told us that the fridge was unrepairable. Great, what was I supposed to do with this hunk of metal now? I called Home Depot back, and they ordered me a new fridge, added a five-year warranty for free, and the Store Manager even dropped off a small dorm size fridge for us till our new one came in. Yeah for Home Depot!!!! I would recommend no one ever buy a Maytag product again - what a piece of junk. Their customer service didnt even care; they had the same old story - We will get back with you in 72 hours. Maytag was good when it was built in the US; now its just more China Junk.

Maytag/Whirlpool dishwasher control panel FAILURE MDB7749SAM - Just like all the above comments about this dishwasher... I too have been a victim. Control panel stopped working after 1 1/2 years. Turned on by itself like other have commented and will not let you push any buttons. Maytag/Whirlpool refuses to do anything about this at all and will cost me over $250 to fix an appliance I purchased at $499. How disgraceful of a company to not stand by their product... A huge shame on you Maytag/Whirlpool for not standing behind your product. If anyone knows of a way to get involved with a class action suit against this company I would like to get in on it.

Maytag refrigerator - After 3 months, a water line broke and caused $350 in damages to our kitchen floor. The next month, the ice maker jammed. The next month, the ice maker went out. I have agreed to let the Maytag repairman (youve seen the commercial where he never has anything to do) use our spare bedroom. Seriously its the worst appliance, by far, Ive ever owned and Ive had plenty as I am 71 years old.

The washer that always needs repair! My first problem with my Maytag washer was that the sensor needed replacing (wont wash or spin). Since then I have had the sensor replaced and motor replaced. Today, I had to call for a service call, and was told that I have to wait over a week! Bad customer service!

A few weeks after I purchased my Maytag MEDC300 dryer in April 26, 2009, I noticed it gradually did not dry as hot as when I first used it but the element did not go out totally until April 2011. Now its November 2011 and the element is out again. Maytag is sending a service man, of course I have to wait until Monday, I am now inconvenienced 2 times in a year.Theres also what appears to be a burn mark on the back of the drum. Two years ago, I paid more than $400.00 for this thing and when it does work, you have to run it over and over again to dry your clothes. Wow! really energy efficient. What a piece of junk! I had my old dryer 10 years before an element went out. I did buy the Lowes protection plan that was sold with a No Lemon Policy. If the product requires more than 3 repairs for the same failure, theyll replace it, it says in the front of the brochure.In the small print on the back, it states 3 repairs for the same failure in one year. These companies are making money off us consumers who buy Maytag because of the name and what is supposed to be quality, and are ripped off by these insurance programs that say one thing but another in the small print. Big business is nothing more than robbers who get away with robbing the hardworking American people. When is it going to stop?

This Maytag refrigerator is a counter depth so a little smaller in the Inside than I would like but fits in my tiny kitchen great. It has an inside water dispenser which is so nice because it keeps the clean look on the outside. It’s a year old and so far I have not had any problems with it.

I had a brand new Maytag refrigerator freezer delivered to my home. Not three days later, the freezer compartment is frosting over on the back wall, while the refrigerator fails to keep my drinks cooler cold like I demand. Ive heard of planned obsolescence, but this is ridiculous!

I purchased a brand new MHWE450WW01 Washer and MGDE500VW2 Dryer in February. The dryer takes forever to dry something; seriously, 3 hours for jeans! The washer sounded more like a jet engine taking off. I called Brothers Main, they sent a service person who identified right away that it was a known problem and he had over 6 repairs already, but be prepared to wait up to 3 months for the replacement parts. This is ridiculous. The service center, you can never get through to them and when you do, they dont seem to care. I had a 10-year old washer that made less noise than this brand new one that I spent $1800 for.

I bought a Maytag washing machine, model number MHW6630HW2 in January 2021. It works fine on ordinary loads, but it cannot spin the water out of bulky items, not on any setting. I put my machine-washable winter coat in the washer and it left it full of water. I re-tried on 4 different settings, and though the washer spins, it cant spin out the water. I went to the Maytag support site. The sites said my model doesnt exist. The phone number for support does not allow you to get any support other than a service call. The Chat option doesnt give a lot of support either. They said that if I call for a service appointment and the service technician finds that the machine does do a spin cycle, then the appointment is not covered under warranty.

Purchased a Maytag four door refrigerator and it leaks water all over the floor. Every few days I remove ice from the bottom of the freezer.

The fridge is very loud, leaks water from ice maker, runs all the time. I have had two repairman out to try and fix it but still not fixed. It is one year old now. If I could get my $2100.00 back I would take it and run. It so loud we have to turn up the TV so we can hear it. Drives us crazy.

Side by side refrigerator model #msd255oveu01. I bought this refrigerator Apr. 2011... The 1st year, the ice kept sticking in machine or freezing up. Now they have had to replace the modules 3 times. Once fall of 2012 and and again yesterday, 3/19/14 and they had to come back today to replace that one. I have called Maytag and they wont stand behind it since the warranty is over. I have told them that this is an ongoing thing with the ice maker and I have had to have it serviced ever since I have bought it. I told them from the git go that the ice maker needed replace. The ice dispenser also drops an ice cube on the floor on occasion and if I use crushed ice it jams up. This product is defective and is not a good product.

I have had it since 2011 and still works as good as it did back then. I love it. Hope it helps people decide when they go shopping for a dryer. I have a dog so I have to keep her clean so I wash a lot of her bedding and she sheds a lot. She also sleeps on the with me so that other bedding that I put for her on my bed between her clothes and mine which I do separate. The dryer works a lot and it is still going strong.