Faulty Maytag Bravos electronic dryer model MEDB400VQ0 - I purchased a new Maytag Bravos washer and dryer in Feb 2011. About 3 weeks ago, I noticed the dryer not drying my clothes. They were hot, but not dry, leaving them hot and steamy. There was also wet lint that kept accumulating inside of the dryer. I took the back off of the dryer to see if there was an obvious problem and I found the blower belt and large bolt that holds one end of the belt to be off and laying on the bottom of the dryer. I have also looked online and did a search on this make and model and the issue I was having, it brought numerous people having the same problem on multiple internet forum sites. Apparently, there is also a service bulletin on this exact issue, but according to the Maytag customer service department, no recall. Therefore, I am out of luck as far as getting any kind of repair (unless I pay for it) because I am out of warranty by 3 weeks. I purchased the Maytag brand thinking this was going to be the best and will last me a very long time. Unfortunately, I was wrong. It only lasted me one year without breaking down and the customer service department is horrible. You can tell they definitely dont stand by their name, the Maytag name is a thing of the past. I will never recommend this brand to anyone else for purchase and I regret having swayed my mother to purchase the very same set I did. This has been an awful experience and I am wishing I had chosen a different brand. Maytag leaves me angry and very much dissatisfied.

A month ago I purchased a 25 cu ft side by side. First the recirculating fan quit. It was repaired. But the water and ice hose in the door froze and cracked the entire freezer door. Must be replaced, unfortunately they dont have any, so I was quoted 6 weeks for a new door, that has turned into 12 weeks and they cant guarantee me a date. I requested a replacement fridge and was told, They cant do that. I purchased the full Maytag package - stove, dishwasher, microwave. I expect better customer service than that, Take a door off the assembly line and ship it to me.

The worst washer I have ever purchased. Clothes DO NOT come out clean, smell musty after washing. Have even decreased the amount of clothing per wash. Cant use bulk load function: throws LF Code - Bad water valve. I will NEVER buy or suggest anyone buy this piece of JUNK! Then to top it off you have to constantly chase the machine around due to wash load becoming unbalanced. Now today have to contend with a burnt smell...

We had a Whirlpool stove/oven for many years, and it was finally time to trade it in. Everything about that unit was good. While shopping for another Whirlpool, the sales rep told us that Maytag and Whirlpool are one and the same. That we found, is false. An important feature for us in an appliance is the self cleaning oven. The Maytag oven had to be leveled four times after it was installed, in order for the self clean feature to function. The self clean part is only a small indented portion of the bottom of the oven, not the entire oven. And even that does not clean. After going through the dealership service about this problem, I contacted Maytag. My final frustrated summary to the rep was that I understand that we bought a lemon, and you are not going to help us in any way. I just want to say to anyone considering a Maytag stove and oven, raise your standard. If you choose Maytag, you will only be disappointed. I am.

I wrote the below to Maytag on their FaceBook page, of course havent heard anything back from them. Adding this on since I forgot about it, I have dogs and wash their blankets often, not that theyre dirty just for the dog smell. I have to wash them on the sanitize cycle which is an 1.5 hours long because if I use the normal cycle which is only 43 minutes they come out smelling exactly the same way they went in. I saw someone else post that their mothers front loader doesnt put in enough water so Im wondering if thats what happens to mine. So wish I would have checked the reviews before buying, thought I was getting a great washer buying Maytag.This is what I wrote on their FB page: I bought a Maytag front loading washer on 5/10/16 which was delivered and set up on 5/13/16. On Wednesday 10/19/16 it stopped working, so just over 5 months from the day it was installed. I called your company on 10/20/16 for repairs, they couldnt get here until today, 10/24, so 5 days with no washer. The customer service rep had all the details on what happened and Im sure passed them along to the repair company. He ran diagnostics, said it was the drain pump which was obvious even to me, but claimed to not have one with him even though they were in stock. Cant make it back until Wednesday, so two more days with no washer. He then proceeded to tell me that the dryer had to come off (stacked on top since the washer is a front loader) before he got back, that the warranty wouldnt cover two people coming out. So Im supposed to spend more money to hire someone to come out, take off the dryer and then pay them again to come back and put it back on. I called the customer service department again and was told they dont cover installation which stacking is. She said the warranty doesnt cover stacked units, as far as I can find that isnt stated in the warranty so please let me know where that is stated in writing. So I have a just over 5-month-old washer that needs repair already (bodes well for the future doesnt it??), will be without a washer for almost a week because the repairman didnt bring the most obvious part with him (maybe wanted to be paid for two calls?) and have to pay someone else for installation so it can be fixed. So wheres the Maytag man? I am not a happy customer and will be letting as many people know as possible. Ill be in the market for other new appliances soon, will sure as hell make sure theyre not made by Maytag, Whirlpool et all.

My model has 2 ovens which I love. A smaller one & a regular sized one. It also has a cooktop. The cooktop always has “marks” on it from the pots & pans. No matter how careful we are, the pots leave marks. We even bought new pots & they leave marks. Something that we do like is that 2 of the burners have “select a size” so these burners can be used for small or larger pots.

I purchase my Maytag Side by Side Refrigerator back in 2006 New. I purchase a Maytag based on the supposedly quality of their Products. And I have stove, and dishwasher as well. A week ago, after purchasing groceries, and made it home. The Refrigerator had gone out. I tried calling Maytag without success and broke down and called sears repair to come out. Well they made it today, and I was informed the Compressor had gone out, and would cost me $998.00 to repair. Of course I told him to get out of my home, because at that price I could purchase a new one. And you can bet it want be a Maytag ever again. I am so disappointed in their claims of being the best. Hype!!!

Please save your money and do not purchase a the Bravos XL MCT Washer and Dryer! I am sickened by the fact that I spent $1,800 on the biggest pieces of junk there ever was. Youd think a company like Maytag would be able to build a product that worked properly. We are getting ready for our FIFTH visit by a service repair company that will only plug in their computers and say nothing is wrong. Well here is what is wrong: Washer does not rinse all of the soap and I have many, MANY, pieces of dark clothing that are ruined because of the white streaks all over. I have done EVERYTHING the service guys have said to do; use less soap; use the deep water wash cycle, etc. etc. There are only two of us in the household so my average load size fills the EXTRA LARGE drum maybe half full so all their advice hasnt worked. It does not rinse the water out of a load of towels (remember there are only two us so not that many towels) and I have to run it through a rinse and spin cycle. Waste of time, energy, AND money. I washed a single coverlet and had to run it through a rinse and spin cycle twice to get the water out! If you use the bedding cycle, it runs for 90 minutes and still doesnt spin all the water out! The dryer is not better either. On average, it takes one hour and ten minutes to dry 3 bath towels, a couple of hand towels and a wash cloth. One of the service people that came out, checked our dryer vent and said everything was hooked up correctly. Talk about a waste of energy!! I would do anything to get rid of these pieces of junk but we spent so much money on them Im stuck until I win the lotto or something! I cannot stress enough that you will be wasting your money if you buy any washer and/or dryer product from Maytag! Believe me, I regret it every day!

I purchased a set of Bravos 4 months ago and what a bad purchase! I wish I would have researched here first. Being environmentally concerned, I bought it because it was supposed to be high efficiency and low water usage. My clothes are being destroyed by this machine. They come out in a massive tangled ball, covered in ink and animal hair (after a wash or two, they are completely embedded into the fibers). Sometimes there are dry spots after I take a load out of the washing machine. No idea how that could happen. It torn my favorite sweater, ripped sheets, bore a hole in a towel, ripped pillows, and DOESNT EVEN CLEAN! I have to wash my clothes twice MANY times to get the dirt out which doesnt bode well for energy efficiency. Im calling them again today to try and get them returned for advertising that they will save me money. Not even close! They are a rip off! I gave my 35 year old set away and wish I had it back! Maytag is JUNK!!!

If you are looking for the Maytag repairman he will be at my house Tues fixing my barely 1 yrs old dishwasher. This is ridiculous to pay this amount of money for the reputation that Maytag is known for or I will say was known for. $270.00 for a control panel. My last Maytag lasted over 30 yrs. Not made in the US - not built to last and this was told to me by the people that installed it so take it for what its worth. Look elsewhere. My last Maytag product.

13 months after installing the dishwasher, the touch pad no longer functioned. Called Maytag 800 number and they said out of warranty. I sent out repair man and he gave me a price for repair totaling approx. $300. Called back to Maytag and asked for a supervisor, she agreed to send the parts for free and I had the repair man install. Out the $120 for the repair and wonder how long it will last this time! I will consider a buying an extended warranty? Next time I will buy a lesser priced dishwasher with a dial, no more touch pads.

I give the Bravo T/L Washing machine and the Maytag company zero stars. I had to call for service 3 times within the last 22 months, twice for the electronic panel which needed to be changed, and the third time, it needing a new tub/drive shaft assembly at a cost of $405.27. I did receive a call from the Maytag customer service and all they would do is make a note of my complaint. I feel if you pay almost $1,000.00 for a machine it should work for more than 22 months. I believe Maytag manufactures an inferior product.Not only did it not last, my family and I found that the clothes didnt come out as clean as it should have, and sometimes, the towels would have a mildew smell to them after washing and drying. I assure you that I have read the enclosed instructions of how to use the machine, load the machine, and only used products designed for the machine

Bought a new maytag gas range march 2013 model #mgr8674ab. The oven would not light at all. Would just click. Still under warranty. Called the service. They came and had to replace the controls in back. 2 months later the same thing, only this time it comes on and goes right back off. Then a week ago got it to light, used the oven and tried to turn it off and it would go off but immediately light up again. Scary to say the least. Another call to service. They are coming tomorrow. This is November 12 2013. I would not buy another maytag gas stove. There is something terribly wrong with this model.

We purchased a Maytag Bravos X washer 2 years ago. Theres not enough water in there, and the clothes get so tangled that Ive had holes in them. Ive had technicians come out several times and they just say that its the water saving feature of the washer. I put it on the wrinkle control setting and the clothes come out ridiculously wrinkled. All of these problems are due to the water saving feature. I absolutely hate this washer and would never recommend it. I want my old washer back with the agitator and enough water in there to actually wash clothes.

The lid on this washer cracked twice. It is made out of plastic and is now discontinued. The lid cracks no matter how gentle you are with it. It is just over a year old and will have been serviced twice. The lid has to be ordered and you have to wait for a week. Maytag will not offer a new machine.

Please let me know if there is a class action suit. My lower freezer froze within a year, now 2 years later same problem. Im all in, this is clearly a design defect that we are all paying for. I would have bought something else. Ridiculous product.

I purchased a Maytag Bravos washer in 2009. I have had nothing but problems. Since, it seems that this washer was never tested nor perfected but just put on the market to sell to us, the consumers, the company does not care that this washer breaks down constantly. First the pump had to be replaced, then the tub was replaced. These were nothing compared to coins falling through to get caught in the pump and cause the washer not to drain. When I bought my washer, I also purchased an extended warranty not knowing that if the washer were to breakdown to many times, Maytag would refuse to repair under the service plan that I purchased because now they are telling me that by letting the coins fall through is abuse of the washer. Really so what they are saying is accidents will not be covered, I thought thats why we purchase insurance.Thank You, Maytag. I will never buy your product again.

Dishwasher cleans well but the top rack is poorly designed for taller glassware. Unit has the typical features - wash, sanitize, rinse only, high temp wash, heated dry, light, normal or heavy wash, and delay start up to 6 hours. Standard dishwasher face; nothing fancy, no dirt catching features, very satisfactory. Electronic features (start, stop, etc.) broke after very little use. This is my second Maytag and a repeat of the first. Will NOT purchase this brand again!

My grandmother got a Maytag Bravos XL MVWB755 washer and from day 1 she had to call Maytag with issues due to residue left on the clothes. They told her to not use this setting... buy this detergent... only use cold water etc. Never did they offer a repair guy to come out. A year passes still having issues shes out of warranty. They now offer a repair guy but claim theyre going to charge her $90. Once she explains to them that she was never offered a repair guy & they shouldve done this before. They decided to waive this fee and send a repair guy. Once the technician comes out to the house they do absolutely nothing and they fill it up with water say we need to clean it and Ill come back out and do another diagnostic. When they come back all they do is fill it up with water get a glass check the water and say, Nope, no floating residue. Everythings fine. They then tell her she needs to get a water softener which is going to be hundreds of dollars.The technician also says do not use any other settings except for these two. Can someone please explain to me why they have all these dang buttons and settings if were not supposed to be using any of them and why all of the clothes come out with soap residue scummy residue all over them? The old washer never did this. It was a Kenmore and its the same water same everything but this Maytag washer is been nothing but problems. It leaves the residue which is stripped all over dark and white clothes, it is extremely loud, not all the clothes even get wet! Maytag is been extremely uncooperative with assisting my Nana. They tell her no one else not one other person is having this problem but when I look up this issue I find that about 2500 people on this forum are having very similar problems. Something has to be done. Maytag should have to take responsibility for this washer. The bottom line is it supposed to be an XL. When my grandparents are washing its only for two people. Theyre not even filling that washer up of all of the clothes are not even getting wet. It just goes to show you that the energy-efficiency that they claim is not working. The washers not getting enough water inside of it. Its not fully rinsing the clothes and no one should have to put the clothes in wash them then do a whole another rinse cycle just to get the dang soap off. So basically at this point she stuck having to do multiple washes using way more utilities than she should have to and Maytag is basically going to do nothing. It wont help her over the phone the technician is a joke and it looks like so many of you people are having the same issues.

Had Maytags since we got married (57 yrs). The first one lasted over 30 years, the second about 15 years, then got a Kenmore that washed beautifully, but lasted 3 years. Have a newer Maytag now that is supposed to be more efficient, but takes forever to wash a load. The biggest disappointment with new appliances is there is no timer to let you know what is happening during the cycle.

Purchased Maytag dishwasher model # MDB4709PAB3 8/2012 @ Lowes in NY with extended warranty. After a while, noticed wood floor warping in front of appliance. Called repair and after several tries, they couldnt repair leak under door. After many complaints to Lowes and Maytag, was finally issued a new dishwasher 8/2013 same model #. Person that hooked it up couldnt wait around to see if all was okay. Ran dishwasher after he left and as usual for this model it leaks worse than before. Called Maytag complaint dept and they said they would issue me another dishwasher of my choice and same price through Lowes. But they never spoke to Lowes and Maytag will not call me back. I would think there must be a leak problem with this model. Do not buy. It is not worth the trouble!

This range cooks evenly, producing satisfying results every time. It’s easy to use, simple to clean and serves me well daily. It has a double oven feature with a smaller oven on top which is not only convenient but energy-saving. The top features a cooktop which is easy to use and maintain. Never had a better cooking appliance!

I have had the washer and dryer for a little over 2 years. The washer already needs to be replaced as the cost to replace the drum is almost as much as a new washing machine by another brand. Thought Maytag was the very best. I had a GE washer for years before I purchased this set. The GE wasnt broken but THOUGHT I was upgrading..NOT!!! Will not purchase Maytag again. Very unhappy!!!

I purchased the Maytag MDB8959SBS dishwasher back in 2014. I have historically been a Bosch guy when it comes to dishwashers but I have been so happy with my Maytag Maxima washer and dryer, I wanted to give their dishwasher a chance. Well, it has been a major disappointment, to say the least. For starters, it just doesnt clean that well. I am very careful in how I load a dishwasher. I do not put baking sheets across the bottom rack lol. Consistently we find dirty dishes. Then after about a 6 months, I noticed the paint on the adjacent cabinets were peeling in spots (near the top and bottom corners). I started feeling around the outside of the door during the wash cycle and there was a fair amount of moisture collecting around the outside of the dishwasher seal (or non-seal). Fast forward to about a month ago, I noticed a burning smell in the kitchen while it was running. Did the typical check the heating element routine thinking something fell down and was burning. However, it was perfectly clean. Emptied it completely and ran a totally empty load. The smell was still there. I eventually figured out the smell was emanating from the upper right corner of the door. Coincidentally this was right above the location of the control board. I grabbed a tool and carefully removed the front panel and discovered wires were melted (some fused together) and even the inside of the panel (which is plastic) was melted in spots as well.So yes, I could have contacted Maytag and sent pictures and fought with them over a repair but to be honest, I have no interest in keeping this appliance. It has been trouble since day one. Again, to be fair, I have had good luck with their other appliances but this was an awful experience and a total waste of money. I have since gone back to Bosch and could not be happier.

Before today I was happy with my washer. Well yesterday I heard this loud noise. It turns out to be the gear case on my washer. To my surprise the repairman told me that it would cost between $450 and $500 to replace. I called Maytag to check on the 10 years warranty and was told that it would cover the basket and the motor but not the gear case. That is very stupid because without the gear case the washer will not work. This gear case help the sensor work, the basket work. DO NOT BUY ANY A MAYTAG PRODUCT. They do not stand by their product. I have had my washer for 2 years and 10 months. Before this the last washer I purchase was a Lady Kenmore through Sears. I had that washer and dryer for 25 years.

We bought a Maytag Neptune front loading washer from Bens Maytag in Surrey four years ago and it has been nothing but trouble. There is no screen in the machine to prevent small things (like coins, screws) from going behind the rubber seal and into the pump. As a result, coins frequently block off the outflow to the pump so the machine doesnt drain.We have had to pay for service calls more times than we can count, and have spent more than original price of the machine making repairs and replacing the pump. We now have learned to take off the hoses and open the pump to remove coins ourselves, which we have to do every few weeks! Bens Maytag tells us that its our fault for letting coins go in the wash. There is no accountability for the faulty design of the machine that allows this to happen. We should have cut out losses and thrown this piece of junk out three years ago. We want Maytag to take responsibility for the faulty design of this product and to credit at least our purchase price toward another machine that works properly!

I purchased the matching Bravos Washer and Dryer in April 2010 at Lowes. I also purchased the extended warranty to have coverage for 4 years after purchase date. I noticed the dryer sensor is not very accurate. The purpose of the sensor is to detect when clothes are dry and then end the drying cycle automatically. However, it fails in both ways. When the dryer stops on its own, the clothes are still damp. I have the setting on NORMAL>LOW HEAT>NORMAL DRYNESS (the reason for the low heat is not to fade/shrink clothes) and even though the heat is on low, it should still keep running until the clothes are dry. So when I open the door and feel the clothes, they are still damp; I turn it back on to run again. If I dont check on it every 10 minutes, the dryer just keeps running and the clothes are bone dry. The sensor should detect this. Once, I decided to test it to see how long it would run with dry clothes and it ran for an HOUR before it shut off. Talk about a waste of electricity.The washer also has issues. First is the SHEETS setting. This setting is supposed to prevent sheets from tangling/balling up. Every time I use the sheets setting, my washer stops with the UL error - uneven load. Meaning, I have to babysit the washer because otherwise, it will stop and wait until I pull out the sheets and loosen them up. I am only washing 1 fitted full size sheet, 2 flat full size sheets, and 4 pillow cases. The reason I bought this machine was because it is supposed to handle king size bedding. Apparently, this washer cannot even handle full size bedding and I refuse to wash each item individually - the machine is supposed to save energy, not require extra loads. The second issue I am having, which resulted in me calling to utilize my extended warranty, is tiny rust dots on my clothes! About 3 months ago, I noticed one of my t-shirts had 4 tan spots smaller than the size of a dime. I assumed I spilled something on myself. About a month later, I noticed it was on another top. Then I assumed it was something on the back of my chair at work causing the spots. It seems to happen every couple of weeks because another article of clothing had these mysterious dots on them. Once, it appeared on my towels and sheets. I realized it was not me spilling anything on myself, nor was it from anything on my chairs. Now, I wasnt sure whether it was the washer or dryer, but I noticed when I pulled out a white sweater from the washer, there were 3 dots on it in the front, and I definitely would have noticed these before, which is how I came to the conclusion it’s from the washer. I cannot see any rust inside of the washer basket so I dont know where its coming from, but I am certain it is not from other articles of clothing (such as zippers or snaps); and the reason I know this is because I do not wash towels with clothes and also, I am 8 months pregnant and have been wearing maternity clothes for the past 5 months and they do NOT contain any zippers or snaps. I took pictures of the rust stains on various items and combined to 1 image. Now, I called my extended warranty to have a service technician come assess these three problems. Well see what happens.

I bought a Maytag dishwasher less than two years ago. The Maytag repairman just informed me that the control panel, the control board and the harness were burnt and needed to be replaced with parts costing over $300. I said, No, thanks. I paid him the $99 service call fee and called Maytag to see if they would help. Nope, they pretty much said, tough luck.

I have only had this Maytag dishwasher for 2 years. My control panel has gone crazy! The child lock is blinking and I never touched it. I have tried to clear it by touching the heated dry button for 3 seconds, every once in a while it will clear. It eventually will start blinking again on child lock. I did research and have found out that Im not the only one that is having this problem. I now have to get it fixed.

We bought the combo Maytag Bravo 300. The issues with the dryer are that it doesnt heat right, have to run the thing twice, after the first 50 minutes the clothes are still damp and it sounds like its going to take off. We had a service man tell us that it was the fan blower rubbing. Now for the washer. It sounds like a b-52 taking off in spin cycle. I know that its the bearings, bearing kit 80 some dollars plus the bearing tool another 80 some bucks. Dont think Im going to invest in Maytags game. If there is ever a class action lawsuit please put me down or notify me.

I bought a Maytag side by side fridge freezer in 2010 at a cost of £2000. Having come back from a week away it had entirely defrosted spoiling all the contents. An engineer came to look at it but said the fault was unrepairable so he wrote it off. Maytag (Whirlpool) think that it is perfectly ok for a 5 year old fridge freezer costing two grand should now pack up. I, on the other hand, do not... They offered me £700 of the cost of a new Maytag. Joy! I thought. However, this one does not make ice or have chilled water (the principal reason for buying Maytag in the first place). I was then told that this was the ONLY fridge freezer in the entire Maytag or Whirlpool range. Is there nothing else you can do to help? I pleaded. No was the reply. The moral of this story is going posh on an American Fridge freezer is not guarantee that you will get the after sales service that the price would suggest.

In December of 2013 I purchased a Maytag clothes dryer model Neptune. In July of 2014, I was hearing a banging sound as the drum rotated. As a mechanical inclined person that I am I removed the top of the dryer and turned the drum by hand. As I turned the drum I noticed that the stainless steel crimped bead around the drum had separated just enough to hit the side wall of the dryer. I was able to bang down the raised portion of the raised bead. This was a quick fix and there was no more banging as the drum turned around. Then in June of this month it started to make that banging sound again. So I removed the top of the dryer and discovered that the bead separated again and then there was a crack that spread to about 1 1/2 inches. I banged down the raised portion again and this lasted for 2 weeks. That’s when I noticed that the crack spread further apart and actually ripped a hole in the left side wall of the machine and froze in position where it would not turn at all. So I reversed the turn of the drum by hand to allow the drum to turn again. At this point I decided to order a new drum which came to $264.00 which included shipping. When it arrives I will replace the entire drum. Being that Maytag/Whirlpool refused to honor their product because this issue happened after the warranty had just expired and the company didnt want to replace the drum. I have never heard of a dryer drum seal bead coming apart in all my experience with repairing an appliance. No I wouldnt suggest purchasing a Maytag/Whirlpool product to anyone. I feel the company should have done the right thing and replaced the drum. In life if you do the right thing all the time, then there would never be an issue with the consumer and corporation. Always do the right thing and you will never go wrong.

I purchased this dryer in September 2011. By August 2012, one month before the warranty expires, the thermo fuse blew and the dryer would not dry; no heat. I replaced fuse and 30 days later, it blew again. I replaced it again and now, March 2013, 6 months later, the same thing; the thermo fuse blew, no heat. The vent is clean and air flow is very good. Maytag will not admit a problem. This is not an inexpensive dryer; it may be cheap, but not inexpensive. Maytag quality appears to have vanished. I have Maytag throughout the house but will think twice before purchasing Maytag again. Chinese produced parts/products are inferior. Maybe Ill look at Bosch or LG from now on.

I did not purchase it. This range came with my home. The electric range works great. It is thorough and I dont have to worry about the gas being on and filling the house up. Electric may not be for everyone, but it is the way to go for me. I will look for similar if not the exact same make/model if a replacement is necessary. I dont mind spending a little extra to ensure the product will last. So many products dont last nowadays and it is sad. I am not an avid cooker, actually I tend to mess up a lot of food recipes but the electric range helps me to reduce the number of problems I run across with the durability and accountability of the product. It cooks throughout the entire dish/pan and I have never had a problem with the unit working properly, just the user not working properly. Haha.

We bought a new dishwasher 2 years ago. Top of the line Maytag Model #MDB8959SBW3 $749 plus tax. We bought this one because they told us what a great 10 year warranty it had. Found out that is a lie. The only thing the 10 year warranty covers is the stainless steel tub, the racks and chopper blade. The stop button on the control panel (circuit board) quit working and the dishwasher wouldnt start. When I called Maytag they said So sorry. It broke so soon, but that is not covered.We were told by a repair shop that Maytag has had nothing but problems with their control panel and the control panel part alone is $150 plus tax plus installation. Our old Maytag lasted 13 years and was still running great, but needed to be replaced because the racks were rusting out. I wish I would have kept the old one. I will never buy Maytag again since it is now made by Whirlpool. If Maytag is having so many problems with their control panel, they should be recalling them.

I was always impressed with the front loading spin washers commonly found in laundromats. The top loading Maytag Bravos does a great job of cleaning clothes and does not stick another door in your way when loading or unloading it.

I had a Maytag washer and dryer for over 25 years. I loved them so I replaced them with the Maytag name. They are not the same company as far as pride and product workmanship.From the get go it always had a dirty odor to the tub, as though the clothes had been left in it for days. I was told to just run through a cycle with bleach, but nothing. There is no lint collector and after about 8 years of using this washer, the old lint is in the bottom of my washer after every wash. Now, I have to deal with the thing coming to a screeching stop, not spinning out the water after the wash cycle. Sometimes it’s full of water and other times some water drained, but the clothes are full of water and not spun out.Now tonight, I went downstairs and found water on the floor, it’s leaking. My question is to call and get it repaired or not waste my money and go buy another brand. I may go with the latter.I purchased a fridge and dryer at Home Depot a few years ago. I wanted to stay away from Maytag name. I purchased another name only to find out it is part of Maytag. No wonder I’m having trouble with my fridge, making ghost-like howling sounds so loud it consumes the entire house. So annoying. Stay away from Maytag. They are not the same reliable, take-pride-in-work company.

Similar to dozens of others, we purchased a Maytag dishwasher from Home Depot in March 2011. Recently, it stopped working, dead - no lights, no action. Called Maytag and they referred me to a Maytag Repairman: Coastline Appliance Service of Huntington Beach, CA. The serviceman came out and spent 20 minutes, checked the door switch for continuity, and declared the control panel bad. How do you know its the control panel, I asked. Its my gut feel, based on experience, he said! He charged me $129 for the visit and said a new control panel would cost $380! After reading other posts online, I can only conclude that a new control panel (if that is, indeed, the problem) will also go bad in the next year or two. So, like so many others, were off to buy a new dishwasher - and we will never buy a Maytag or Whirlpool appliance again.

The Maytag Washer Model # MVWB835DW is the worst I have EVER had!! I have 6 kids, my husband and myself who I do laundry for and this was supposed to be a XL washer so I can do large loads! It does not do anything to stains and all my clothes come out with clumps of powder and if I use liquid it leaves greasy residue on them! Everyone in our home has had rashes from the washing powder not getting rinsed out and my husband who gets grease and oil on his clothes has all stained clothing because of this washer that does NOT clean anything! I used to be able to get every single grease and oil stain out until I purchased this washer! My 9 yr old now has a scalded skin from the washing powder not getting rinsed no matter how much I use!! I even tried using vinegar to make it dissolve and it does not help! No matter what we do it does not fill up nor wash the clothing properly!! This washer needs to be discontinued immediately and anyone who has it have the option of exchanging it with a better washer! It is absolutely ridiculous that they know this washer does this yet keep selling it!

I purchased a Maytag stainless steel French door model the middle of 2006. While cleaning the French doors with the cleaning product given to me with the purchase of the new fridge, I notice what looked like coffee on the doors. It wasnt, it was rust on the stainless steel doors. I called the service tech and they came out. Rubbing the fridge, he told me it wasnt rust. He took a closer look and found that it was in fact rust. He called his office; they told him that rusting on the doors has been an issue lately. He charged me $65.00 for what I already knew. I called Maytag and it took a while, but they decided to send new doors. However, I had to have a Maytag rep install it, which would cost me. I didnt have it done. Two years later in 2010, the French doors felt hot to the touch and the inside was warm and not cooling. The freezer was fine. I called for a tech to come out and it’s another $65.00 to fix a fan motor that blows cool air from the bottom to the top. Oh, it’s not under warranty because it wasnt inside with the motor. Total cost: $235.00. In 2010, I woke up and opened the fridge to get milk out. It was warm and so was the inside of the fridge. I thought it was the same problem, but the freezer also was warm. Upset and not wanting to pay for this again, I unplugged the thing and started using a little fridge that I have stored in the basement. It has no freezer. Today, I finally got over being pissed and decided that I would have a tech come out and find out and finally fix it. The tech said that the compressor has failed and it would cost $790.00 to fix. Im not having it fixed, so it’s another $65.00 gone. The tech said that the compressor in Maytags/Whirlpools has been a pretty big issue lately. All I can say is that I will not ever purchase Whirlpool products again. From inside to the outside, this product has been unsatisfactory. I just noticed that the rubber is failing on one of the French doors. Wake up, Whirlpool. Model number is MFD2561HES.

I purchased both the washer and dryer in this series. First the washer does a horrible job actually cleaning the clothes unless you set it as a bulky load and use more water. Despite that issue, after only owning the set for four years the dryer broke down. It made a terrible noise and you could not run it because it was far too noisy. My husband thankfully bought a replacement part and fixed that issue. A few months later I started having trouble with the washing machine. It freezes constantly and I have to unplug to get it working again. It usually take over 15 times to actually get it to begin to fill with water. Now it started to stop working during the wash cycle and I have to unplug it again to get it going. Most times I have to change it to another setting like rinse and spin or drain and spin to complete a wash cycle. Last night it began to have a plastic burning smell. I used to own the same washer for 20 years and only had minor issues that come with extended use. To only own this pair for under five years and have them both break down proves that these are poorly made products and you should save your money and purchase a different brand altogether. I will never buy another Maytag as long as I live if this is how well their products are made. I expect to have my appliances last longer than five years for their price. So save your money when it comes to these machines. I promise you will not be happy with your purchase. I will either have to repair the washer and hope it will last at least a few more years or chalk this up to a lesson learned and discard both machines.

Two years ago I purchased a Maytag Top-Loading HE Low-Water washer. I have always taken great pride in the way my laundry looks and smells but since this purchase, my laundry no longer smells clean and fresh nor does it look clean. I have always used the same detergent and fabric softener (only now I use the HE version) and it served me well. I have read all of the directions and did as I was instructed. I cannot believe that anyone would actually think that you can do laundry with practically no water. Do the decision makers have not common sense at all? I didnt and still dont believe it but what choice did I have when all of the machines are now HE with low water. I think its terrible that consumers dont have a choice. I have come to realize that low water, HE washing machines actually waste more time, energy and money (detergent and fabric softener).My clothes are not clean, nor do they smell good when the wash cycle is finished so I have to wash them again, using more detergent, fabric softener and energy. The super fast spin that supposedly sucks out most of the moisture, also rumples my laundry with semi-permanent wrinkles (even on the low wrinkle setting) so clothes that never had to be ironed before, now need pressing. I find it remarkable that, with all of the detergent ads promoting washing clothes in cold water to save energy, we are told that if our clothes are not sufficiently clean in cold water in our HE washers, that we should try a warmer/hot temperature. Good luck with that because my machine has several temperature settings but only uses one - COLD! I cannot actually believe that with all of the technology that our society holds, we are going backwards in the basics of washing clothes. Terrible product, terrible quality, terrible results, terrible waste of time, resources and money. Why cant you just leave some things alone??

Purchased 4 Maytag kitchen appliances - stove, double oven, fridge, dishwasher - was told that they were all made in the USA. WRONG. The microwave comes from China - not sure why Maytag is not being honest. Not happy with my purchases - even though we spent $4000 to buy American. Warranty service is awful - even extended warranty is a joke. Would never purchase Maytag again.

I bought Maytag frost-free refrigerator last August 2006. But now, I noticed that ice builds up in the freezer. The product is only five years old but I was told by Whirlpool that they had discontinued making defrost heater. The reason why I bought Maytag was the ad on TV showing the Maytag service technician seating and doing nothing, implying that Maytag brand is a good product. Think again before buying Maytag products.

On 11-10-10 I purchased a top of the line Maytag fridge. All had been great till we needed a part in Nov. of 2014! After nearly 3 months of searching they tell us that they no longer make parts for this unit and I am out of luck! Fridge works great but the center seal is broken (french door - Mullin) they quit making the part???? I am beyond angry! Will never buy Maytag again!!!

Purchased this Maytag dishwasher (Model DB7749SBM2) from a Sears 2014, no problems until now in late June 2014. The control panel is not responding. Start/Resume light is off, pressing it doesnt seem to do anything. Cancel light is off, pressing it does trigger the cancel drain process. Wash Cycle choices either dont respond, or for 2 of the choices engage an incorrect cycle. Option choices dont respond. Delay light comes on when an incorrect cycle choice displays but stays at 2 hours, cannot be toggled off or to a different delay length. Holding Control Lock or Delay for 3 seconds doesnt seem to clear the circuit board logic. Problem began with the Cycle choice buttons defaulting to Rinse Only. Control panel behaves not at all or incorrectly as described above. Seems to be a common Maytag control board/panel problem. We need help as we are unable to afford repair or another dishwasher. This time, it will not run at all. I called customer service today (August 11, 2015) and they expect me to pay for the repair. Repairman already said electronic board bad at a cost of around $300 just for the parts. It is easy to Google and find multiple review sites that indicate hundreds of consumers have similar problems, but Maytag will not acknowledge any issue. Based on the pattern the warranty is not going to help as it goes out just after a year. For only having it 1 1/2 years it is becoming very expensive. There should be a recall on this control panel.

I bought the Maytag Bravos XL 5.3 washer because it was advertised to conserve water and it was a good brand, but it was a horrible mistake to buy this washer. The washer barely uses any water to clean properly and it hardly moves any of the clothing. The only thing that does move is the clothes at the bottom while the clothes on the top stays still. After using it for a day, I decided to return it back to Home Depot where I bought it, but they did not accept it and told me to call Maytag to return it. I called and the person who answered gave me different numbers to call. After going through ten different numbers, I finally received someone that could help me and they told me that I could not return the washer. They told me that the only way to return it was if there was a mechanical problem with the washer. It is extremely frustrating because I paid over $800 on this washer and now Im stuck with this garbage because I cant return it. I recommend everyone to not buy this washer otherwise youll get the same problems I am getting. I have to manually stop the washer and move the clothes by hand.

I purchased a Maytag dishwasher four years ago and it has been serviced six times in those four years. Not just small things, main parts. Control board twice, control panel twice, and cleaning terribly the other two. They replaced the control board once and then would not do anything after that. I just got it replaced four years into this nightmare only because I bought a Sears home warranty plan and they are replacing it. I would never buy a Maytag appliance ever again.

I bought the Maytag Bravos XL HE washing machine because I needed a machine that could handle large loads to save me time doing multiple loads for everyday items like jeans to towels, blankets as well as delicates. This machine is a COMPLETE disappointment. It does NOT get anything clean unless I wash it 4 times with bleach and pre-stain 4 times. You know what bleach does to your clothes! The water level is so low I can only wash 4 things at a time and I still have to wash additional times. It doesnt get the smell or food stains out. Not a good choice for an active family or person. Ive had clothes come out with suds still on them after washing three times. I use less than the recommended amount of HE detergent. There was a $250 agitator washer by GE at Lowes but it was smaller - how I wish I bought it. These impeller HE machines dont work. My advice steer clear of this Maytag product unless you like to waste your time re-doing loads of laundry.

Purchased matched set washer/dryer on May 21, 2013, machine always took over 1 hour to dry medium load of laundry, but dealt with it. On June 5, 2014 made a horrible bang, followed by a grinding sound, ran to turn off. Hubby took apart, thanks to Youtube video and found that a screw was lodged in the fan blade, had broken a tooth and the motor mount broken....took fully apart, ordered fan blade to replace. When went to put back together, realized the WALL (bulkhead) of the dryer was broken, metal was too thin to support the tiny bracket to hold the motor.Called Maytag, NO HELP, told me to call a local repair guy for an after warranty service. Called repair company and was told he has NEVER seen this in a newer model dryer, contact Maytag, contacted them again by live chat and told not under warranty and no one has ever had this problem. Do NOT buy anything from Maytag. THEY DO NOT BACK THEIR PRODUCTS! If you have had this problem contact me, Im willing to spend a day or two in small claims if necessary to prove my point!

My four year old Maytag stove blew out the lower heating element in the oven. The model number is MER8880AW. I removed seven small screws to confirm what the problem was and remove the element. That is a short life span for a stove element. My wife checked our paperwork and thought it indicate the part was covered on the 10 year warranty. Called Maytag at 9 AM and went through the press numbers thing, being put on hold, call dropped, told they were not open twice, etc. Finally got a person to talk to at 2:45 pm. Yes the part is covered under warranty, but no they will not give me the part.A repairman must plug it in and put the seven screws back in. This will cost me a lot more than the $50 the part cost me at the local appliance store. 10 year warranty. Wow, WORTHLESS! There WILL NEVER BE another Maytag or Whirlpool in my house. Making a big deal out of their warranty when they are going to soak you bad for a simple install is just plain dishonest.

Recently May 2019, bought a Maytag Bravos Washer, HE. Its now installed and so disappointed with this product. Not enough water to wash Clothes. Would of taken cashback from Maytag, but cant wait 6 to 8 weeks for cashback. 6 to 8 weeks after they have washer picked up. How long did we want to go without clean clothes, hummm. Problem was looked at by a professional appliance repair company sent by Maytag. His opinion, suggestion was, washer just didnt deliver enough water to wash clothes. I know its HE, suppose to me water miser, but Maytag Bravos just doesnt give enough WATER. How do we get clean cloth like that. As I mentioned in summary, I have added attachment close proximity to add water to washer raising water level to wash Cloth. Yes with proper water it does clean good, JUST NOT A AUTOMATIC WASHER now. Were only two, Rural NB, up to 3-4 washes per week, more when company around.

Purchased this Maytag dishwasher from a local Home Depot in Feb. 2014, no problems until now in late July 2015 (about 18 months). The control panel is not responding. Start/Resume light is off, pressing it doesnt seem to do anything. Cancel light is off, pressing it does trigger the cancel drain process. Wash Cycle choices either dont respond, or for 2 of the choices engage an incorrect cycle. Option choices dont respond.Delay light comes on when an incorrect cycle choice displays but stays at 2 hours, can not be toggled off or to a different delay length. Holding Control Lock or Delay for 3 seconds doesnt seem to clear the circuit board logic. Problem began with the Cycle choice buttons defaulting to Rinse Only about three days ago. I assumed user error so let that cycle run, then was able to choose a different cycle (cant remember which one) which also completed. But since then the control panel behaves not at all or incorrectly as described above. Seems to be a common Maytag control board/panel problem, so will probably replace (with something other than Maytag) rather than repair.

Purchased a Maytag Dishwasher (Serial # P33706417) in Sep. 2013. In the beginning was working fine. After a year and a half started having problems pushing the button to start, not starting. Had to wait a few hours then hit it again and all the lights would light up and then it would start washing. Then when done, some lights stayed on and never went off. Then a month or 2 later, same problem but only a couple of lights would go on and when done 2 lights would blink continuously. After several months now, none of the lights are working and cant get dishwasher to start. Called a tech and he said the control board and the touchpad were not working. Would cost me over $400 plus shipping, etc. to for new. Very frustrated with Maytag, as we havent even gotten 2 years out of this dishwasher and the 1 year warranty has expired. DONT BUY A MAYTAG!!!

Dryer delivered nonfunctional. Tech showed up the following Tuesday. Diagnosis main board and one sensor dead. Tech returns following Thursday. Replacement board DOA. New dryer still nonfunctional. Awaiting new board with no functional $1100 dryer. This dryer replaced my three year old Maximus which was deemed too expensive to repair after three repairs. Please do not buy a Maytag/Whirlpool product.

We purchased a Bravo Maytag series top load washer from Sears in June 22nd 2013. See receipt for verification of sale. It seemed to be alright and we were hoping to be a lucky consumer, but now it is January 2015 and today I could smell smoke along with a weird smell (like an auto repair shop smell). I immediately was concerned about the entire house catching fire. Luckily I figured out the smell was coming from the washer and was able to pause it, stop, and then turn off. We are not happy. Our whole main level smells awful. And Im pregnant so this is probably not good to be inhaling. We are looking for recalls that may be out but weve only seen front load recalls not top loaders. When we bought this it had great reviews, but now it appears there are so many complaints, so my question is: Why isnt Maytag doing something about this massive problem?

We paid over 2000.00 for our refrigerator in May 2011 and within a year ice started forming on the bottom and then leaking out on to the floor. Every week I have to get out large beach towel to lay under the pull out drawer, break up the built up ice and then pull it out onto the towel. I too called Maytag who said it was out of warranty. Now today I notice a significant temperature drop in the refrigerator and freezer. Whats odd is that the day before yesterday the freezer was so cold the ice cream was solid as a rock. I have not changed the factory settings since it was installed. I HATE MAYTAG!!!

All I ever heard was Maytag is the best so I purchased the washer/dryer over a year ago and have had nothing but trouble from the get go. It takes an hour and a half to two hours for a wash (if youre lucky). Normally, I almost always have to stop and restart it and move clothes around, babysit it. I cant wash but four or five garments at a time. Its a piece of junk and I tell everyone I talk to, never buy Maytag, ever.

I had a stove my mom bought for me 26 years ago. Still worked perfect. Used constantly. In 2018 my husband had to have this stove. Said no my stove my mom bought and still works perfect sentimental plus three children using it. Not one problem. So he buys this Maytag stove I didn’t like but don’t cook much warming things up or frozen pizza. Go to our sons for holidays. Always next day cook a turkey for sandwiches. Open the door which is too heavy. Wouldn’t close and called my husband. Got it semi closed. Said we’re not eating it. He proceeds to cook. Door opened. More turkey is in garbage. My husband started reading. I also did. Looks like these Maytag stoves are garbage. Make a lot of money for repairs. Now this goes to dump. No one stands behind their products. Is it worth paying to repair no.

I purchased a Maytag Dishwasher Model MDB7749SBM3 in January of 2014. I have had issues with the control board for the past month: lights come up at random; it takes 3 to 10 trials to get it to start and now it is dead. After reading many reviews on this site, I now understand what the problem is. I called Maytag customer service and they wanted to schedule a service call at $98 just for the diagnostic. I asked the Maytag associate whether the control panel issue was a common problem and she said she would research that but did not give me an answer. I am totally disgusted by this company!!! I would be happy to join a class action suit.

This Maytag dishwasher is beautiful inside and outside. I love that the controls are hidden. It cleans dishes very well. It has a large capacity for dishes, a rack for glasses/mugs, a small rack for cooking utensils, and a container for silverware. It is so quiet you hardly know it is working. I would highly recommend it.

We purchased a bottom freezer refrigerator from the Home Depot in 2013 and I am sorry to say this refrigerator does not deserve any stars. Immediately after the warranty was up our refrigerator started leaking all over the floor. The drain clogged and freezes up on the bottom under the freezer. When it becomes full, it leaks all over my hardwood floor. I have now become a slave to this refrigerator. Each week I have to open the freezer and get down on my hands and knees to break up the ice, scoop it out, toss it in the sink. I have spread the word and I hope anyone who reads this does as well. Never buy a Maytag product because not only do they make defective products, they wont own up to it and recall it.

I will never buy another Maytag product, and moreover, will tell everyone I possibly can, not to do so either. Like many others, I have a two-year-old dishwasher that needs a control board already, and from what Ive read this wont be the first time. It would cost $150 for the part, plus the service calls make it around a $350 experience. The only choice is to pull the machine out, or buy a 5-year warranty for another $318.56. Grand total for your marvelous high quality Maytag that lasts only 7 years? Around $1,000. I am so sad, the company used to symbolize quality but now when I see the logo, I think of landfills.

This dryer ripped a gaping hole with sharp shards of metal exposed. It was working fine, and then it made a weird noise. It stopped and I assumed my laundry was done. We go to remove clothing and cut hand open on exposed metal. As if that wasnt bad enough, several hundreds of dollars in clothing had cuts in them. This dryer worked great for years, and out of the blue this happened. Im a widowed disabled mother, and cant afford a new dryer.

Do not buy one. Maytag is unresponsive to repairs or parts that are needed. They are not even manufacturing the part that breaks. If you are lucky, you will find out there is someone who will fix the defective computer board... But Maytag will not tell you. We were without fridge for 4 months... They did not care.

This set is a GREAT ONE! I love my HQ washer and dryer. The washer has so many settings to choose from for all different loads of clothes. It washes and spins everything great. My dryer is so nice! I can dry a load of whites: towels, washcloths, hand towels etc in record amount of time. I would highly recommend them both.

We purchased a Maytag dishwasher in January of 2011. Two years later the entire machine stopped working. We had purchased the extended warranty and the control board and panel were replaced. Now two years later it happens again. Maytag/Whirlpool is of no help nor do they care. DO NOT purchase their product!! Multiple complaints and issues with faulty control panels and the cost to replace one is the same as buying a new dishwasher so they cant lose. I will never again own a Maytag or Whirlpool product.

Purchased an over the cooktop microwave 3 years ago, it came with a 20 year warranty. It stopped working and I promptly emailed Maytag customer service. It took them over 3 weeks before they responded. That is not acceptable. Did they think I had a back-up microwave to take its place until they finally got around to reply to me? Well we could not wait, and we just threw that piece of junk out and had it replaced with a competitors unit. We will never buy Maytag again and will inform anyone we know about the poor operation of Maytag products and lousy customer service. My suggestion to anyone considering Maytag products is to not waste your time and money and look to another manufacturer.

My Maytag MDB7749SAW0 Dishwasher starting acting up after around the first year. The lights on the Control Panel began to flash uncontrollably and it will run all day while I am at work. I called Maytag and they were nice but did not repair it because the warranty just ran out. The person on the phone said that it is a common problem with knob-less dishwashers, the humidity causes problems with the control panel. The cost to repair was over $300 to replace the control panel.

I tried emailing Maytag but from what I read on consumer reports I doubt Ill get an email back. After our 20 plus year old Kenmore fridge was taken by hurricane Sandy I decided to try Maytag. What junk! We have a bottom freezer and were getting water build up on the bottom under the basket. In order to keep the water from leaking on floor I had to chop the ice out of the bottom every 2 days. My husband got frustrated and took the whole freezer apart only to find all the coils were covered in ice. Soon after that the ice maker stopped working. Tried different things to get it working. We finally took it apart and found the factory did not screw in all the screws on the inside so they fell out on the circuit board and shorted the thing out. Lucky it didnt burn the house down. All I can say is junk! Do not buy!

Tried various cycles and I hear water going in but don’t see any water. How does this wash clothes. I want to see water and soap clean the clothes. If I want dry cleaning I will bring the clothes to the dry cleaner. Never again will I buy a high efficiency washer. My clothes do not come out clean!

The Maytag Neptune FAV6800AWW Washer has to be the crappiest product I have ever bought. I bought it brand new and hardly ever used it. The first time it broke it was luckily under warranty, although we had to pay for the repair man to install it. It took two new circuit boards before it was fixed. A few months later, the circuit board went again, and it was conveniently for Maytag now out of warranty. The repair man told us that their company never carried these washers because from the get go they had a ton of problems. He said that the odds of it breaking again were great and that we would be better off putting the money into a new washer.I dont understand how the company, in good conscience, could continue to sell a product to consumers that they knew was faulty. It was not a cheap washer and I have never been so disappointed in my life. You would think they would have had a mass recall or, knowing how many problems consumers were having with the product, offer so much money towards a new one.I laugh at the commercials where the Maytag man was bored because their product never broke I could have kept that man busy for months!

I bought this washing machine 2 years ago or so. We have always bought Maytag. My mother still has hers she bought over 25 years ago and it still looks and works great. So my wife wanted a new washing machine so I said were going to get another Maytag. Boy did I screw up. What a piece of ** junk. Sounds like its grinding gears all the time, so loud. I close the door in the wash room and I can still hear my investment on a Maytag grinding my nerves because I spent so much on a product of a brand Maytag that I thought would be around for a while. Do not buy a Maytag.

I purchased a Maytag double door refrigerator in 2012. So far the deli drawer has broken 3 times in the same way. There is a plastic peg attached to a side panel on the refrigerator. This pin breaks off after a few months of use. To repair it, you have to replace the entire side panel. The parts and labor costs are about $200 each time. It is obviously a design flaw that Maytag should fix. If you repair it every time it breaks, in about 8 years your repair costs are more than your original purchase price for the refrigerator. Dont buy Maytag products. They are inferior.

Our problem started when the control lock button locked itself on. Called Maytag and told it wasnt covered by warranty but they did walk us through resetting the power and it fixed the problem until we ran the next load. Now when you try and set it, the rinse only light comes on. Bought the Maytag because I always believed them to be dependable - wrong!! I had a basic model Whirlpool running for a family of 5 for 25 years prior to this Maytag without ever having to call a repair person. Maytag wont deal with the issue so I would recommend to anyone else having any issues with unreliable appliances to do what I am doing - boycotting Maytag!!

Purchased a new Maytag washer (MAH5500BWW) and matching dryer along with the pedestal that they sit on in late November of 2003. Spent well over $1900.00 for everything including the delivery charge. I noticed the build up of mold/mildew inside the washer starting in early 2005 but cleaned it every week or so and it seemed to go away. As time went along the mold/mildew smell got stronger even after each cleaning that I did with bleach. Nothing seemed to help.It wasnt until 3 days ago when I had my dryer vent cleaned by a professional company that the technician looked over at the washer and said You know that washer was recalled and that there was a class action lawsuit against Maytag about mold/mildew issues involving that model. He opened up the washer door and looked and was shocked. He told me that he himself had the same Maytag model washer and was notified by Maytag years ago about the class action lawsuit. He told me that he had received what he called a buy back check from Maytag. I wondered why I had not been notified since I had purchased both units new and registered both with Maytag after my purchase.I decided to do a search for my washer model number and looked for mold/mildew issues and was shocked to find thousands of complaints involving this issue with this model of washer. I then called Maytag/Whirlpool and this is where the fun begins. I called and explained to the customer service rep at Maytag/Whirlpool what the problem was with my washer and asked her why I was never notified of any recall or class action lawsuit involving my washer. After thinking for a minute or two she says that she is unaware of any problems with my model of washer and asked me to recheck my model number. I do this and again she says that she is unaware of any problems associated with my washer. I explain to her about the thousands of complaints on the internet about this mold/mildew problem and she then says I shouldnt believe everything I read on the internet.At this point I ask to speak to her supervisor which she says she transfers me to and the fun continues. The supervisor then tells me that the customer service rep whom I was speaking with is new and doesnt remember the issues with my model of Maytag washer but she herself does remember the issue of mold/mildew build up inside the washer. I ask her why wouldnt this issue of mold/mildew in this washer be in your system for this rep to be able to refer to? She then says that since this issue was so long ago its not in their system anymore. Huh???She asks me if I was part of the class action lawsuit involving this washer and I explain to her that I was never notified of any such lawsuit so I couldnt have been part of it. She then says that Maytag has since settled this issue long ago and since I missed signing up for the class action lawsuit I was just out of luck. Somehow its now my fault for them not notifying me about the class action lawsuit years ago!She then offers to send out a repair person to look at my washer and to look at the mold/mildew problem. I ask her if the service call was free and she snickered and said no, why would it be free? I tell her I thought it should be free because I paid nearly $2000.00 for these machines because I was looking to get the top of the line machines. Now I have a mold/mildew infested Maytag washer that smells and looks so bad its a assumed health risk. She again tells me that the service call will not be free and asks if I want her to schedule it now. I quickly decline!She then tries explain to me in some odd fashion that I should be happy that I got 10 years of service from my washer/dryer and hoped that I would continue to purchase Maytag. What??? Are you crazy woman!? Now its me who is laughing at this point. I almost say some very bad things to her but better judgment takes hold and I just hang up. Now you have heard my story and Im now looking for another washer/dryer so I can remove this health hazard from my home. I will never ever buy anything that has a Maytag/Whirlpool named attached to it.

The control panel and the electronic control box had to be replaced after only two years of use. It cost almost as much as a new dishwasher (492 dollars). The model of the Maytag dishwasher is MDB77479SBM3. This dishwasher looks good from the outside and runs quite but the electronics are cheap and cant stand heat without melting. My wife and I are retired and only used this washer about twice per week. It looks good, cost 650 bucks and it is a pile of junk. No more Maytag in our house. We had this machine installed in July of 2014... It crapped out in July of 2016.

I bought my Bravos x washer and dryer set three years ago. Ive never been happy with them. You have to put the washer setting on bulky to even wash a normal sized load and they still dont come clean. Only three years old and Ive had problem after problem with the washer. As Im typing this I have a full load of clothes in the washer that will not wash, its full of water and wont even drain and spin. PLUS the lid wont unlock. So aggravated.

My Daughter got me a Maytag oven with the AquaLift technology and is a piece of Junk. Half the time the Water is still there when the cycle is over. The water has made it between the front glass pieces and the finish on the top of the stove looks horrible, it just looks dirty. The knobs are cheap and the fake chrome finish is flaking off. Unfortunately Im stuck with it because I cant afford a new one... this was a gift to me because Im disabled and it was to make my life easier.

We bought a Maytag refrigerator bottom freezer at Home Depot in 2012/10/15. A few months ago, a sheet of ice formed on the bottom of the freezer. Since the warranty expired, I decided to look at the problem. Now, I am a mechanical person who usually can fix just about anything mechanical. I used a hair dryer to defrost the freezer and saw that the drainage hole was frozen over. I took the entire freezer apart, cleaned the drainage channel, the drainage hole and reassembled the freezer. No more than 24 hours later, the drainage hole was covered with 1/4-1/3 thick ice, the drainage hose and the tray were dry, and the bottom of the freezer was coated with ice. This one problem that I could not solve. The design is so poor, the draining water freezes over the hole before it drains. I read some of the consumers complaints and I just want to add that do NOT waste your money on repairmen, or parts from Maytag, the refrigerator is NOT repairable. I will write off my loss of $900 and look for a new refrigerator, but Maytag will never see my money again.

Maytag Microwave MMV4205DW-1 - This microwave made it one year and one month before the door would no longer latch shut and the control panel stopped working altogether. Called Maytag and was told not under warranty. It was going to cost more to repair than to purchase a new microwave that was a different brand.

I purchased a Maytag Dishwasher in March 2013 and the control panel failed in July 2014. I, along with hundreds or thousands of others it seems, discovered that this is an extremely common issue with several models of Maytag dishwashers. Rather than standing behind their products and making it right for their customers, Maytag is hiding behind their one year warranty and refusing to do anything about it or even admit they installed thousands of FAULTY control panels. This has been an expensive, infuriating issue to deal with and I have never been so dissatisfied with a company. Bottom line, they made a bad product that should have been recalled. It blows my mind that they are getting away with this. I wish I had known the recent changes in Maytag/Whirlpool and I wish I had done my research prior to the purchase.

When purchasing new, sales person highly recommended Maytag products. Maytag Dishwasher MDB7749SBW3 - This had the SS tub that my wife was looking for. Now only 19 months later it has completely stopped working. A few weeks ago the lights on the control panel would randomly come on or not align with the wash option that was chosen. This lasted a short time, and then lights on the panel would stay on, and not allow you to choose any options. I reset our breaker and this alleviated the problem for another week or so. Then it stopped working all together. A quick Google search and it was obvious Maytag has a MAJOR and KNOWN issue with this model. The ribbon going into the faceplate/ control board sits directly behind the port that exhausts the steam. This ribbon over time becomes corroded and eventually malfunctions. I called customer support. They were completely unwilling to acknowledge the problem and also unwilling to help in any way. They offered to sell me an extended warranty @ $329.00 that would cover the service call and repair. Very unhappy that their product has an obvious defect/ flaw and they are completely unwilling to acknowledge/ or stand behind their product. We are a family of (3) and run this dishwasher about once every 5-10 days. Unbelievable they find a fail rate within a year and half with light use acceptable!

Like in a previous posting I also have a Maytag dishwasher, model MDB7749. Just this weekend we had our third control panel go up in flames. Thankfully the breaker hit and it burned itself out quickly. We had previously had one go out where it would just restart in the middle or near the end of a cycle. One other time, we heard the popping and saw the small black smoke come out from under the panel covering. This last time we were in the other room and heard the popping, and then smelled the burning. Aside from the panel issues, this has been a decent dishwasher. But at this point with a third repair I could have bought a new one. This is the only appliance I havent bought the extended warranty on and I regret it. Hopefully Maytag will add this to their previous recall.

Dishwasher worked fine for the first 12.5 months, and lo and behold 1 month after the warranty expired, I had my first repair, a new motor. A few months later, I had my second problem, the thermostat. A few months later, I called Maytag because I thought that the control panel was probably shot (based on my previous Maytag for which I replaced the control panel 4 times, before Maytag finally agreed to get me a new dishwasher). At that point they sold me an extended warranty which for 300 they would make this repair, and any other repairs for the next year. They have been out 7, yes 7 times, in 4 months. They would probably be out more often, but since it has been difficult to get a repair person out here, more time than not Im washing dishes by hand. Their customer service is horrible, their products worse. Still waiting for the dishwasher to be repaired. They wont send out a different company, even though they have been out here 7 times, and keep coming back. Even when it is repaired, they will not cover the cost to replace the soap bin, the racks, the wheels on the rack, and all the little pieces made out of the same quality plastic as the stuff I buy at the Dollar Store (except when that stuff breaks, it doesnt ruin my hardwood floors). Dont buy a Maytag, roll up some $100 bills and light a match, because you can look at a pretty flame and wont raise your blood pressure dealing with their customer service.

Never had a better washing machine, highly recommend this product: MVWC425BW. Saved plenty on water usage, no rust and no service issues after 6 months.

Have 2 fridges (one regular and the other is a side-by-side, both were bought in 2006 at Future Shop. The small one is not freezing and the side-by-side ($2,200) is busted too (compressor wont start....). How can Maytag say that their product are reliable on TV??? A Fridges compressor should last at least 15 years !! Maytag, you should at least have the decency to pay for the compressor!

I would like Maytag to repair or replace this dishwasher. It has only been installed since November 2014. The only button that works is the auto clean. None of the buttons work. I thought Maytag was a reputable business.

Never buy from Maytag. I and my daughter bought from them two refrigerators of them. After one month my daughter started to fix. I am started after one year or it is leaking. Our freezer destroyed and realize this after one day all my food I throw away. The same was with my daughter refrigerator. My daughter have old refrigerator it is working without problem for 50 year never fixed. Never ever buy from them anything. It is good I was at home. Sometimes I am traveling if it happens this time. I do not want to think about this. For fixing you have to pay lot of money. I hate that I purchased something with them.

Neptune washer and dryer, an all around good buy. Low water use and large capacity for the pair. Bought the pair in May of 2001 and have only had one, very minor, service call. Buying online usually proves to be the easiest and cheapest way to go. Economical delivery costs. Noise and vibration and overall solid construction. Dancing washers can be a real cause for being a deal breaker. Auto shut off for balance is a must. Cleanliness of wash and wear caused by washing and drying. Large capacity and multiple cycle selections for both the washer and the dryer are necessary.

I am in my 24th year of using my Maytag washer and dryer. The set was purchased in 1996, so it has been well worth the money. At this time, it does not spin out as well as it used to, but I just fluff the load and spin it again and then it is ready for the dryer. I have been very pleased with the set and have never had to have a repairman work on them. Cant ask for more than that!

Our Maytag refrigerator was about a year old when we noticed rust on the edge of the stainless steel doors. I called Maytag and they were nice enough to replace the doors even though the warranty had expired by their standards. Keep in mind, the warranty starts when you purchase the product, not when you install it. We ordered our appliances from Lowes well in advance of our kitchen remodel so we would have them when we needed them. The time our appliances sat in Lowes warehouse used up two months of our warranty.Now, the new stainless steel doors are rusting and they are refusing to do any thing about it. Should stainless steel rust? Maytag doesnt seem to care whether their product performs the way they should. Its all about the warranty. Once the warranty lapses, they could care less whether their product blows up. Thats the customers problem. Whatever happened to building a quality product that lasted and customers bought for generations? Obviously, thats a thing of the past.My goal in writing this is to make consumers aware of appliance warranties. When I spoke to Lucas, a Maytag customer service supervisor, he informed me their products offered no warranty on the finish of the product. So, according to Lucas, the finish on your brand new Maytag appliance could flake off like dandruff and its your problem regardless whether its a manufacturing defect or not. Remember, buyer beware!

We have owned the dryer (Maytag Bravos) since Dec. 2010 and are now on our 4th service call. Upon the second delivery of the part that was ordered last week - we will be on the 5th service call. I finally asked Maytag if I could get a trade in since this dryer is obviously crap. They said they could only handle the problem at hand, which is the same problem over and over and over. The flywheel was left off all together. The pulley belt for the dryer pops off about every 4 to 6 months. Ridiculous. Its a crap dryer, dont buy one!

Bravos gas dryer - three issues in three years. Same issue twice, clothes are not drying. Now I have company coming and have to deal with his issue. The blower motor went. So, I have paid for a new dryer in repairs already. The washer is making such a loud noise when it goes into spin cycle that you have to turn the volume up to the highest level on the TV and it is still tough to hear. It’s unbelievably in the horrible quality. Make the product and parts in the USA and stop buying junk from China and Mexico. This is good American money that is flushed down the toilet with Maytag as well as your reputation. Fix your quality control and do the right thing!

I purchased Model #MGR7661XB (Gas Cooktop and Oven) in November 2009. From the very beginning, we realized it was a mistake and looking back, we should have sent it back.The finish, both on the stove as well as the burner racks (the removable grate that the pan sits on when cooking) has some sort of coating that instead of repelling grease and food seems instead to actually attract it. Any hot liquid or grease actually seems to melt into the finish and becomes impossible to remove. Essentially, our stove was ruined within the first week. We have even tried putting a scouring pad on a wooden spoon and scrub with as much force as we can muster - to no effect. Short of using a putty knife, and completely destroying the finish, I cant think of any way to resolve it.As for Self-Cleaning ... yeah, right. Use for entertainment purposes only. It doesnt clean at all.The latest issue is now the oven lights about 20% of the time. The broiler still works and we have discovered that we can trick the stove by allowing the broiler to heat up the stove to about 200 degrees first - then, when the oven is already hot, the oven part will ignite.Speaking of igniting ... from the beginning, this stove has the loudest ignition system I have ever heard. You can hear it ignite click/pop from two rooms away and the oven cycles on/off every 10 min. or so. It is very annoying.All I can say is, never again will I buy another Maytag. This was supposed to be the upgraded sealed burner model (which also is impossible to clean). This stove is only 4 years old but it was a mistake from the beginning. Like I said, I should have returned it after the first week.

I purchased a Maytag model # MRT 18 FFFHO1 refrigerator from Home Depot. After 7 months, it stopped cooling (wouldnt cool below 52 degrees). Fortunately, I had taken out a 5-year extended warranty. Thats the good news. The bad news is that after numerous trips by a certified repair man -- and three spring/summer months without reliable refrigeration -- Home Depot promised a refund. Well see.Bottom line: keep looking for a refrigerator that works. I have tried GE, Frigidaire, Maytag and Sanyo. Since many of these companies are really just one inept cooperation with more names than Frank Abagnale (Catch Me If You Can), let the buyer beware! I would give Home Depot protection plan 5 stars, though. They stayed with me through thick and thin: by emails, phone calls and text messages. However, their protection plan is worth more than Home Depots appliance products -- through no fault of theirs.

I have a Maytag Bravos washer that has gotten to where every time you try to run the final spin, you get an unbalanced load code and it shuts off - it does this even when you try running it empty. This washer is 3 years old, and has been doing this progressively worse for the last 4 months until now. We cannot even get it run the final spin cycle now.

Lets see... my complaints are the same as the others. I purchased the Maytag Bravos set. They were the higher end units. At first, the machine was very quiet. I quickly had a control board go out. Got that fixed. Now the washer gets off balance on every load.... Every time it spins, it stop. The gears whine very loudly... Louder than any other machine Ive ever heard. I agree with the comments on wrinkled clothes. It also does not clean heavily soiled clothes as well either. Overall, a bad decision.

I have a similar story to Patricia. Been without a fridge for over a month. Refrigerator is almost brand new (bought last year) and a service-person has been out three times (going on 4) to fix it. The fixes NEVER work and then they have to order ANOTHER part and I have to wait for the part AND THEN the service person. I should not have to wait once the part comes in. People who have been waiting should be at the TOP of the list. Then again, this is Maytag...probably EVERYONE has been waiting for a fix.Ill never buy a Maytag appliance again unless they give me a new appliance, pay for the apartment sized refrigerator I was forced to buy while I waited--I have 3 children who need fresh food--and replace the $300 worth of groceries that went bad when I was assured the second fix would work (they wont replace my refrigerator--if they do, Ill be satisfied--unless it breaks in less than a year, too).

This Bravo Top Loading Washer does not thoroughly clean my clothes. It doesn’t fill properly with water, and it leaves soap residue on my clothes, because it’s not using enough water. I’m using the 2 rinse cycle trying to prevent this, and it’s still not enough. It has actually ruined a few of my items. It is the WORST washing machine I’ve ever purchased. I’m disappointed in Maytag for producing such an awful machine and Sears for selling such a sub par product.