We purchased a Maytag Front Load Washer in April 2011. We did not purchase an extended warranty. From the beginning, it didnt seem to clean as well as our 12 year old top load Whirlpool had. Then in Summer 2013 it began to create fabric pulls in fine fabrics - tablecloths, blouses, etc. Whirlpool sent a repairman who charged $90 to tell us that the drum needed to be replaced because of a rough spot. He ordered a new drum and we understood that it would be replaced because it was within the 5 year manufacturers warranty on drums, but we would have to pay for installation. 2 months later, Whirlpool informed us they could not supply the new drum. Why are replacement parts not available for a 2 year old machine? The customer service rep told me that they would replace the machine for 15 percent of the cost of a new machine. All I needed to do would be to pick out a machine and let customer service know the model number and they would make arrangements and contact me re: payment of the 15%. When I contacted them again I was told that I would be expected to pay $508.00. That is 15% of a $3000.00 machine. It it completely unfair. Later, I was told that the first rep I spoke to must have been wrong because they dont pro rate replacements on a percentage basis. I told them that I was not interested and they have lost a good Whirlpool customer. In the last 15 years we have purchased 7 appliances made by Whirlpool. Never again! I am not impressed by their customer service.

I purchased a bottom freezer Maytag refrigerator two years ago. It recently began leaking water onto the floor from the freezer compartment. I just had it serviced and the serviceman told me that it was a common problem. The duck-billed check valve gets plugged. This is a problem with Maytag, Jenn-Air, Whirlpool, Amana, and KitchenAid refrigerators as they all share the same manufacturer. There is a service bulletin out on this that lists hundreds of model numbers affected by the problem (Technical Service Pointer #: W10632338). I think it is criminal that consumers are expected to pay hundreds of dollars to have this manufacturers defect repaired. I tried to find a place with the government to file a complaint, but wasnt clear who had jurisdiction. Perhaps a class action suit is in order. There have to be millions of consumers potentially facing this problem. Anyone with any knowledge of how to further pursue this defect, please comment.

I recently purchased a Maytag French door, bottom freezer. It was delivered and set up by delivery men and when they pulled out the bottom freezer the bin and tray were missing. This refrig should have never been shipped (per Home Depot) and also delivery men. They called Maytag and ordered the missing part. 5 days later it arrives and is not the right bin. I purchased the 5 year warranty contract and after calling 3 numbers and getting shuffled around, they told me it should also have a slide out. They set up appt. for this Thurs. I wanted to file a claim for loss freezer meat and was told Miss, your 5 year warranty does not start until the 1 year manufacturer warranty is up. She also proceeded to tell me that no refund will be issued and they are NOT responsible when their product leaves their plant and gets to me. REALLY... The refrigerator was not properly inspected and still shipped. Not covered under warranty and fridge is 5 days old and have had issues from date of delivery. I will never make another purchase of a MAYTAG and their customer service could use more training and a course is representing their company in a much better way.

The top of the range has blistered and has worn off. It cannot be cleaned. I spoke to a Maytag representative and was told to try and use magic eraser to clean around the burners. This did not work. The model number is mgr7775xs. Is there any solution to this problem. My range looks terrible.

Purchased new Maytag washing machine July 17, 2011. Have had several problems with it over the past three years. Most of the time it would not complete a load of laundry and would get stuck before the drain and spin cycle. Last week, the spin cycle became extremely loud. Had a repair person come out and was told the motor bearings were bad. Estimated repair cost $700. Purchased this unit new for $569.00. Called Maytag, was told that 10-year warranty on drive motor and wash basket did NOT include the bearings. Asked if they could help out with repair cost, was told no. Will never purchase another Maytag product again as they do not stand behind their products. Household has 4 people in it so use of this machine was light to medium.

Our Maytag Bravo washer provided so little water, that our clothes were rarely clean. My husbands jeans gradually developed stains around the knees that never came out, and his white underwear & socks didnt come clean either. After about 3 years, the spin cycle developed a loud sound, like a jet taking off, which was so loud and forceful, it sounded like it was literally going to spin out of the machine. We got rid of the Maytag Bravo after 6-7 years, and Darryls jeans and underwear were clean after two washings. All heavy items, such as blankets, have to be watched over because they always get out of balance several times a wash. We kept the Maytag Bravo, although it wasnt great, and didnt dry clothes completely. These are not machines that you can put clothes in, and just walk away. You have to babysit your laundry.

Approx. 3 year old Maytag Dishwasher Control Panel lights blinking with Dishwasher inoperable. Repair part (new Control Panel) costs approx. $180 plus tax. When you add the cost of a service repairman you are nearly at the price of a new dishwasher. I am completely unhappy with this Maytag Product and will never buy another Maytag Product again.

I have enjoyed my microwave and it has lasted 10 years so far. The only problem I have had is the handle coming off but I clip it back on. Also I changed the bulb. The microwave is over the stove and matched the rest of my appliances. Basically, I would recommend Maytag for any appliances that a person would need to buy.

My family purchased a New Maytag Washer and dryer about 1 1/2 years ago! Thinking that the name was far more Superior than anything we could afford! What a piece of junk! The washer is nothing but flashing codes! Unlevel this and always stopping and starting over with a wash, when in fact it doesnt shake and bounce itself into the middle of the floor! As best as I can describe, it literally needs Hurricane straps to hold it down! You can never wash a full load because it cant handle it! Now! Onto the pathetic dryer! Several weeks after they were installed was the first scenario with the dryer! We had a representative that does work for Maytag warranty to come and work on it, after telling me over the phone that if in fact the lint trap had lint in it, that I would have to pay the service call! Funny!! So after diagnosis he said the belt broke that runs the exhaust fan! He said it was fixed and went on his merry way! Several months down the road! Same routine! Broken belt that runs the exhaust fan! And once again several more months down the road! Guess what!!! Yep!! Broken belt that runs the exhaust fan!!! So now here we are! I am now into the extended warranty that I purchased from the furniture store which was almost an additional $250.00! And voila!!! Its broken again! So being the fed up person that knows what the answer is going to be, I take the front off the dryer like I have seen done so many times before!!! And what to my surprise do I find?? Another Broken Belt!!! So I am wondering!! Why so many broken belts! So I take my flashlight and look at the motor and housing that holds the exhaust fan and I notice that in fact the housing that holds the exhaust fan is BROKEN! Therefore, this is the cause for so many broken belts!!! Well, who should be responsible??? I contacted the extended warranty people! What a waste of time! After setting an appointment for Sears to come work on the dryer and after explaining on several Recorded Phone conversations what has taken place! The service man comes to my home and not even 1 minute after entering tells me that he cant work on it because I have self diagnosed my dryer! What was the purpose in me explaining to them beforehand what I found??? Why didnt they mention then that I should not have taken it apart or hey put the front back on!!! Now after causing a ruckus with the furniture company that I have spent well over $50000 with!! They want to supply me with a 1 time Customer Courtesy!!! Of repairing the dryer!!! Oh did I mention that I am a Professional Diesel Mechanic for a major Trucking Company that is far more capable of diagnosing something like this than evidently the person they sent the first 3 times!! NEVER AND I REPEAT, NEVER BUY ANYTHING MAYTAG!!!

Oven does not have consistent temp, cant change temp without preheating ruining whatever is cooking. 5 visits from Maytag during added warranty and never any satisfaction. Tough Microwave minutes and the oven goes off. Told it was a Govt requirement. Very noisy even after its off. Maytag wouldnt help or Home Depot either who warranty was through.

Well I like all the other people have the very same problem. Ruined floor from sheet of ice that forms on the bottom tray daily. I was told I need a new main board which I understand is about $500.00. I am 55 years old and this was my first brand new fridge. I am so so upset. I grew up with the whole Maytag repairman commercials where he was so lonely cause he never had any repairs to do. All my life I grew up with these commercials. I thought I was buying the best. What a disappointment. It has been in my living room for 2 years. I keep thinking something wonderful is going to happen. Now I have to pay someone to haul it off. Great.

Dishwasher worked fine for the first 12.5 months, and lo and behold 1 month after the warranty expired, I had my first repair, a new motor. A few months later, I had my second problem, the thermostat. A few months later, I called Maytag because I thought that the control panel was probably shot (based on my previous Maytag for which I replaced the control panel 4 times, before Maytag finally agreed to get me a new dishwasher). At that point they sold me an extended warranty which for 300 they would make this repair, and any other repairs for the next year. They have been out 7, yes 7 times, in 4 months. They would probably be out more often, but since it has been difficult to get a repair person out here, more time than not Im washing dishes by hand. Their customer service is horrible, their products worse. Still waiting for the dishwasher to be repaired. They wont send out a different company, even though they have been out here 7 times, and keep coming back. Even when it is repaired, they will not cover the cost to replace the soap bin, the racks, the wheels on the rack, and all the little pieces made out of the same quality plastic as the stuff I buy at the Dollar Store (except when that stuff breaks, it doesnt ruin my hardwood floors). Dont buy a Maytag, roll up some $100 bills and light a match, because you can look at a pretty flame and wont raise your blood pressure dealing with their customer service.

We purchased our Maytag dishwasher less than a year ago and are very disappointed with the poorly designed quality of this product. We had a Maytag repairman look at our dishwasher and he told us that; the dishwasher cleans with enzymes in the dishwasher not water pressure, and we need to make sure the water in the kitchen faucet need to be hot before starting the dishwasher, we also need detergent, rinse aid, and citric acid added to each load. Adding all these products to the dishwasher does not fix a poorly designed product. This product does not clean the dishes, even with rinse aid the glasses come out cloudy. The dishwasher has a power blast button, it does not clean the dishes any better than the regular setting and it runs for four hours. We will never buy another Maytag product.

I cannot even begin to describe my disappointment in these overpriced machines! Bought a 4-year extended warranty when I purchased and two weeks after warranty expired, my heating element went out on the dryer. This repair cost over 300 bucks. Six months later the washer was making some crazy noise and service guy could not find the cause...another $120 bucks. A few months later the same noise...this time a coin had slid under the bottom plate and caused damage to the machine...another service charge of over $200 bucks plus I purchased an extended one year warranty at $189 bucks. Thank goodness, because now it is throwing an LD code and will not drain. Oh and I forgot about the service call for the latch breaking on the dryer door...another $119 bucks. The repair guy felt sorry for me and didnt charge me for the part. Tangled clothes when washed and forever to dry. Next time I will buy an inexpensive set like I had before that lasted 16 years with no problems! This stuff is junk!

We are on our 2nd Bravos XL. The first washer lasted 6 years and there was a part going out that kept making it stop in the process. Basically the repair guy said it will just go out one day so it was up to us to repair or replace the machine. The machine didn’t have an agitator and we had been having issues with white residue on the clothes for a long time but thought it was related to the other part. So we bought a new one, with an agitator. It was the new model. We’ve had it around 6 months and we have lots of issues with the white residue. The only success we have with not getting white residue on darks is using deep fill and very little detergent. We use powder because the liquid makes dark spots on our dark clothes. So either way, there’s a problem. So we are using a lot of water when it’s supposed to be water saving. And we are using much less detergent that the company says. I think it’s the machine that has problems. I’ve read a long thread on Facebook and it appears that Maytag tells you to use Affresh regularly. It also says to follow their instructions. But everyone seems to follow instructions but Maytag takes no responsibility for their product. Makes me sad because Maytag was the best on the market at one time and we will never buy again. Our dryer works fine but the washer sucks. And that was a lot of money that I paid. I hope that Maytag decides to make it right and help their “customers” enjoy their products once again.

Maytag Washer over 3 years old. Often problematic not functioning smoothly! Maytag invented this defective machine to intentionally rob the customer with all the probs that comes with it - poor design & quality, & not logistically programmed! Even aftercare/customer service SUCKS!!! Now, sensor spinning option is no longer working, drum not operational. No more Maytag!!!

Purchased a new Maytag refrigerator in January 2013. In September 2013, the ice maker stopped working and Maytag sent out a repairman to replace the ice maker. In February 2014, the ice maker stopped working again. I contacted Maytag and was told the refrigerator was no longer in warranty. I told them that since the ice maker was replaced in September the warranty should have covered me for a year from that date. The Maytag representative told me that was not had it worked and asked if I wanted them to repair the item for a fee. I bought a non-Maytag ice maker and replaced it myself. It is now July 2015 and the ice maker is still working fine. I am not a repairman.

Faulty Maytag MDB8969 Dishwasher - BEWARE! Whirlpool, Jenn-Air, Amana, Maytag, KitchenAid... Are all brands that fall under Whirlpool. According to Better Business Bureau statistics there is less than 1 chance in 10 that you will get the Whirlpool product you are expecting! We purchased a new Maytag dishwasher at the end of 2016. Within a couple of weeks the dishwasher began failing: discharge pumps, heating elements, soap dispensers, door leaks, faulty racks, rinsing problems... Since purchasing the machine we have had to make 7 different service calls, all under warranty. The warranty service providers have been good but the machine has been a catastrophe, having been out of commission for several of the 18 months since being installed, and causing serious water damage to our kitchen floor (based on several other negative reviews this leaking is not an uncommon occurrence).A few months into owning the machine, after our 3rd service call, we contacted Whirlpool, Customer Service and asked for the machine to be replaced. They refused to replace the machine but extended our warranty free of charge- better than nothing but not a cure to the problem and the only remedial action that Whirlpool was willing to offer. We didnt understand at that point that the problem of faulty and defective Whirlpool products was probably so huge that Whirlpool could not afford to provide a reasonable solution to their customers; leaving many, as witnessed on various product review sites, to bear the extreme frustration and associated expenses borne from the incurred failures. Unfortunately, here we are once again, requesting our 7th service call in less than 18 months, and asking once again for a replacement.The Whirlpool response this time (CSR was not allowed to let us speak to her Supervisor in spite of trying to negotiate that for several minutes) was that they would not replace the defective machine but would sell us a new $850 machine for $250 and would dispose of the faulty machine for an additional $25. Whirlpool would not however pay for the uninstall of the faulty unit nor the install of the new unit (about $350) which would have to come out of our pocket. We won’t be spending the additional $600 to fix this problem as proposed by Whirlpool; we won’t be installing another Maytag product in our home. We were advised that we could fill out a form if we wanted, to try and claim for the damages which the dishwasher caused to our kitchen floor. The form was never emailed as agreed and now we are just really tired of the whole experience so will simply put this all behind us.Our Whirlpool experience has been extremely stressful and quite expensive. It is clear to us that if an appliance which is averaging a serious failure every 3 months since the first day of installation, does not in the opinion of Whirlpool warrant a full and prompt replacement, or even the direct telephone attention of a Customer Service Supervisor, that the Whirlpool quality standard must be so low, the failure frequencies so high, that the number of similar failures prohibits any commercial viability to manage the problems in a reputable manner. Whirlpool clearly has some very large problems. It would not have been easy to destroy the once highly respected Maytag name. Such degradation could only take place as a result of continuous and ongoing Whirlpool quality degradation. We will no longer be their ‘crash test dummies’ but I do hope for the sake of Whirlpool (apparently North American made) that they take ownership of their poor quality condition, realign and spend the next few years becoming the company that we all once knew and respected.

I think it would be nice to state on the box of dishwasher that customer may need a water connecting fitting and hose for their new dishwasher. Yes, I was asked if I needed anything else and I replied I dont think so! Well when I got home, I did need the water supply sweep 90 degree elbow. Or tell sales people to inform there are parts missing. I had to drive back to Huntsville, AL from Hazel Green. Not life or death, just saying! I do like Maytag products. The dishwasher I replaced was17 years old and we had good service! It’s just starting sounding like a rocket motor. Time to upgrade, I thought. Well my wife really thought so! ;)

We bought our Maytag dishwasher at Sears about 2 years ago. It has never cleaned very well, we have to rinse everything almost to the point of spotless before we load it. Its a water saver, which means it takes more than 4 hours to fully cycle. Just today, I went to turn it on and the start button does not work. I looked it up and found that this is a common problem with new Maytag washers. This is really irritating, considering we paid a lot more for the Maytag brand than we would have paid for something without the Maytag reputation. Live and learn, I guess; we certainly will not be buying another Maytag.

Front load washer unit does not respond to control inputs. I have called Maytag service and support. One can find a repair or maintenance manual. Im in a smaller market so there is limited service. Maytag service and online support is terrible. Maytag stores are fronts for independent service companies. Its probably okay, but misleading. Everyone wants to order the main controller board. It would be good to have a maintenance manual.

I purchased a Maytag refrigerator from Home Depot on 5/17/11. It would run, then not run. It spoiled all the food not in the freezer and most of the food in the freezer. This happened early November, being less than six months old. My wife called on 11/8/11, they repaired it on 11/18/11. Ten days of no refrigerator and a lost of about $200 in spoiled food. The company would not pay for any of the money I lost for the spoiled food!

I am very satisfied with my Maytag washer and dryer. Had it for 10+ years. No complaints. It’s easy to set the machine according to my preference for each load of clothes. The dryer is great. Settings on the machines are very easy to use. This is important since I have a vision problem.

I purchased the Centennial Commercial Technology washer in June of 2013. In the last 2 1/2 years it has been repaired 3 times. The transmission had to be replaced twice. My household consist of two adults and definitely it is not overused or overloaded. The washer currently is not working. Consumer service cannot schedule an appointment for repair for 2 weeks. Previous repairs took approximately 2 weeks to schedule a service appointment and it took another week to two weeks to get the part in and washer repaired. I have decided to consider this an expensive learning experience and will not purchase Maytag products in the future!

3 years into the buying of a Maytag Bravos XL MCT washing machine (Serial # **) and already had to replace the original control panel for a cost of $400+ in less than 2 years of the buy. Now AGAIN the replaced control panel is now once again shot and the machine is not starting. The appliance needs to have a #manufacturers recall for the control panel. #Maytag #Whirpool #BetterBusinessBureau Note -- all existing customers, please lodge manufacturers complaint for the control panel issues @ 1-800-344-1274. (Even if you dont pay because of extended warranty or plan coverage, if you are facing the control panel issue year on year). All future customers, buy this appliance at your own risk.

So we bought the whole Maytag kitchen appliance FZ (fingerprint resistant) series suite. That was such a mistake! Id give the part numbers but I think this applies to Maytag in general as it sounds like all of their appliances suck. Ours are 1½ year old and I already want new ones. Over $3,600 for junk. We knew it was no Viking or Sub Zero but didnt expect to flush $4k down the toilet either.The microwave is an over the range type and we have it vented to the outside of the house. The vent works like crap to remove the steam when you have a large pot of water boiling on the stove top. I can put the fan on high and barely any steam goes up the vent, most of it ends up soaking the microwave door to the point where I have to towel it off. The vent will hold up a paper towel so I know its pulling air but the location of the vent in relationship to the large front burners makes it useless. And the self cleaning is as others have already stated - A joke.We bought the fingerprint resistant SS and I would rather have the fingerprints than all of the scratches. Today, and this is no BS, I had a lottery ticket on the fridge under a magnet and I pulled the ticket because I wanted to check the numbers, well I slid the paper about 4 inches while it was still on the fridge under the magnet and now we have these fine scratches everywhere I did this. It wasnt the magnet because it has a felt backer on it, I took the paper off and slid the magnet all over the place, no scratching. I cant believe a piece of paper would even leave a mark at all. This is aside from some larger scratches that someone in the house must have used a feather duster on it or something.The French door fridge is loud and the ice maker is huge! The slide out basket in the freezer always gets cockeyed and stuck like its coming off the track. To line up the door tops you have to adjust the feet on the bottom of the fridge. I have to put ours out of level to get the door tops to line up, well this makes it look terrible in the cabinet space so you have to make a choice of what is uglier - thats just bad engineering. Our old fridge (GE) you could adjust the doors right on the bottom of the door. Its like they forgot this and said, Well you can just tip it one way or another to get them to line up, ya lets put that in the manual. The dishwasher sucks, plan on rinsing everything, even the silverware doesnt come clean. No its not our water.We are so disappointed in this brand which used to be considered very good, what the heck happened? Ship manufacturing over to China? And another thing, I highly doubt this is stainless steel. I know there is ferritic and martensitic stainless that are magnetic but Id bet all of my appliances that this is just regular carbon sheet steel with some coating on it to give a stainless steel look. All except for the range, that is different and doesnt scratch like the fridge, microwave, and dishwasher. Not sure why but probably has to do with the heat so they couldnt use this junk coating, just a guess though. Anyway it doesnt matter, all of the appliances are a complete waste of money. Poor design, poor performance, poor durability, pure junk!

I bought a Maytag dishwasher less than two years ago. The Maytag repairman just informed me that the control panel, the control board and the harness were burnt and needed to be replaced with parts costing over $300. I said, No, thanks. I paid him the $99 service call fee and called Maytag to see if they would help. Nope, they pretty much said, tough luck.

Had this front loading washer 13 months when the circuit board failed. I pitched a huge fit as Maytag wanted to charge me 75% of a new washer for the circuit board replacement. Fortunately they caved. I like how well it spins out and washes well. The door gasket is hard to keep clean. Has fresh setting so clothes do not get moldy if you leave them too long.

We purchased a Maytag washer and dryer from Lowes in the summer of 2016. The washer performed so so. Not a great machine. After only two years use, there is only my husband and myself, the transmission went out. The repairman said it would be cheaper to buy a new machine than repair it. Maytags 10-year warranty does not cover the transmission. We replaced the Maytag washer. I cant say anything good about Maytag.

Excellent dishwasher but door kinda flimsy. Front panel scratches too easy. Top rack needs to be stronger and a bigger bottom rack. Other than that running wise dishwasher is excellent. Its hard to beat Maytag. I think they just build cheap stuff around good motors.

Purchased a new Maytag washer from a local Hardware store chain. Waited 3 days for delivery. Old washer was hauled away. Started using new Maytag Centurion the same night it was received. There was a funny odor coming from the washer that was discounted as new equipment smell. Saturday the Maytag Centurion washer was leaking some odd lubricant that had the same odor as the mentioned new equipment smell. Since this lube had been leaking out in close proximity as the liquid detergent my wife used a towel to clean it up. This towel went into the laundry with other clothes.Now Im concerned that whatever this oily stuff is, it’s in all of the clothing that was washed with the towel. Since I live on the West Coast and Maytag only answers the phone during the week Eastern Daylight Time I will call (2 days) after the fact. You might do well by finding out what this lube stuff is before you take it home and how youll have to deal with it once it leaks.

Once again I purchased a maytag appliance. I was hesitant because of poor past experience. I bought a refrigerator, lasted 3 years, and a stove, a little better 4 years. When I went to buy a dishwasher at home depot, they assured me that maytag had improved their standards and now were more conscious of maintaining the quality of their products. Long story short, I bought the dishwasher in april of 2015 and now in october of 2015 the control panel is shut. I have requested a repair, but find this unacceptable as the life of appliances seems short at best. I am fearful this could be on going as I now am reading the customer reviews, and 90% of them have had this trouble more than once.

I purchased this Maytag Bravos XL Washing Machine at Lowes in California, MD for about $800 on April 8, 2018. What a disappointment for a Made in America product! BUYER BEWARE - DO NOT BUY! I agree 100% with the reviews and comments. This washing machine is a PIECE OF JUNK! It does not clean clothes! It does not provide enough water to get all clothes wet! All it does is shake the clothes back and forth and stays in the same order you put the clothes in. I agree with one of the reviews that it does nothing but crumple/wad the middle items together and rub them. And the clothes are DIRTY!! I will be calling Maytag 1-800-344-1274 and demand for my money back!! Lowes should STOP selling this product!

Maytag washer has increased my water bill; it was supposed to be energy efficient! Also, the washer will not wash a blanket. Sensors will move a large item to one side causing an uneven load which then causes numerous extra fills until stopped manually. I was told to add more items! A blanket barely fits in the tub. I had to invest in lint rollers since the rinse cycle is inefficient. This washing machine is useless. I should have stuck with Kenmore.

Okay, on March 2009, we bought this brand new microwave due to our major remodeling. We didnt move into the unit until February 2010, so the microwave was in its box for 11 months. After we moved in our condo, my husband and I had to travel for work for almost a year so our brand new microwave is very slightly, gently and barely used. Well, for the past 2 months, it had been acting up. Sometimes it heats, sometime it doesnt. For a 2 year old microwave, which we paid over $400, I would assume that it would last. It no longer heats up, so I called Maytag customer service to hear her tell me its not covered under the warranty and would cost $269 for repairs and there was nothing she can do for me unless I pay for a technician to come and repair it! No way, I swear it probably got used 5-10 times a month to heat up coffee for about a year. I am sure there are some major quality issues on this model because when I googled Maytag microwave, all I see is the same magnetic problems. I spoke to a group of my lawyers friends. If youre interested in joining a class act law suit, please e-mail me. I hate that people are being taken advantage of by these terrible companies. I cant believe how low quality their customer service and products are. Believe it or not, my $30, old microwave lasted me 14 years throughout my college years until we decided to replace it with the modern stainless steel one. It got noisier in time but not broken and still heats up just fine. This $400+ one lasted me only for several uses. Shame on Maytag, when I have time, I will be sure to write a complaint to the consumer department as well. I will dedicate my life in spreading the word out about their low quality product. Don’t buy Maytag unless you only plan to use it for a year or 2.

I made the mistake of buying the stainless steel bottom freezer (model# MBL2258XES1) approximately 1 year before the freezer started to make a periodic clunking sound. The repairman responded because my year warranty was still active and found no cause for the noise. Fast forward a couple of months later and it started pouring water out onto my hardwood floors!!! Unfortunately it happened while we were away and my floors were destroyed. Maytag wants nothing to do with me. Im so disgusted. I now have to have a towel permanently on my kitchen floor. Nice. I made the unfortunate mistake of buying an Amana dishwasher recently not knowing that they were also owned by Maytag. The dishwasher is a water waster :( This is very disappointing - you try and buy American and you get screwed. If any lawsuits start up, sign me up!!!

Got woken up to the sound of my refrigerator ice lid flapping. Boy is it loud! Called Maytag and found out it was a recall so they will fix. They set up for someone to come out to fix the following week. That was a flop because they did not have the part. I waited 4 hours for someone to show to find out that Maytag scheduled the appointment for nothing - not only did they NOT have the part but they did not have a clue as to when it will come in. Time is valuable! Here we are 5 weeks later and my refrigerator is still flapping and loud. Has been calling Maytag for them to say that the part has been expedited. Well it has been expedited for more than 3 weeks now! Today they say that it will be another month before the part comes in! Not Good! This is such an inconvenience and Ive lost a lot of sleep over this flapping noise. Its an embarrassment when guests come over to our home! Tired of it!

MODEL: MFI2265XEM1 - ice maker dispenser leaked water while under warranty; took two separate technician trips to repair. Several months later, called Maytag regarding leak and ice at bottom. Technician replaced w/ grommet w/ larger dia drain tube extension; smaller dia causing backup of water & ice. Now, ice maker quit working completely, ice buildup in bottom part of refrigerator and freezer building up frost which means air is getting into the freezer, and yes, the freezer door is completely shut! Please advise if there is a class action suit. Will contact California Attorney Generals office.

Maytag HE Top Loader Washing Machine: I have regretted buying this piece of garbage since my first wash. This washing machine is complete waste of money and a piece of garbage. The Auto Sensing doesnt work and doesnt cover the clothes with enough water. When the deep water wash is chosen the clothes just float around but the agitator doesnt get them clean. Dont waste your money hoping it will work, because it wont. Maytag used to signify quality that is no longer the case. I am going to also give a bad review to the place I purchased this piece of garbage because all stores need to discontinue selling this junk.

Fifteen months after purchase, the lid lock and motherboard goes off. It was replaced with new parts and the machine still doesnt work. Cost of repair is equal to the cost of the machine. With or without an extended warranty, the expense is not worth the investment. While shopping to replace the machine, the dealer finished my sentences on Maytag washers.

Maytag in general has gone from being reputable in the early 70s to being the epitome of a rip-off company that sells junk, then refuses to stand behind it. I have a Maytag Washer and dryer. The washer continually goes out of balance and spins across the floor. Repair people tell us that our floor is not strong enough - funny, our new Samsung washer has no apparent issues with the floor or anything else. Our Maytag Gemini is a piece of crap. The ovens do not work or heat up most days. Maytag pushes replacing an EOC board at $800.00, but then the part is not available. Stove is not even six years old. Maytag is a synonym for junk.

I have had 2 Geminis. The first one was fine, this second one is a mess. I have had at least half a dozen parts replaced. I have insurance to have this oven repaired but have paid to have the window seal replaced on at least 3 occasions. The top of the oven is so hot that when I have used the burners to cook on top I have received 2nd degree burns. I have received burns on several occasions. I asked dealer if I could trade this in but said I would have to sell it on my own. I would not subject this oven to another person as I feel it is very dangerous.

We purchased a Maytag MVWX655DW1 Bravos MCT washer in 2017 and I recall a sloshing sound during agitation. Its a high efficiency model and was okay for several months, I think. It began to make something of a clunking sound during agitation that was similar to the deceleration sounds when the spin cycle completes. It seems that is an indication that something is wrong. Clothes arent clean after washing - another reason to suspect a problem. I observed the wash cycles and noticed that some items dont even get wet during the wash cycle. The clunking is probably an indication of the type of failure but I couldnt find anything other than someone else asking the same question when I did an internet search. Expected performance is shown in a company video with water sloshing during agitation. Thats the key take-away. My basket moves back and forth an inch or two during agitation and makes a clunking sound at each direction change. Water isnt sloshing through clothing and some of the garage rags that were once my clothes probably just needed a good washing. I suppose that even cleaning the washer isnt accomplishing much. The spin cycle is actually impressive. I load the washer evenly and find the completed loads with a towel or shirt evenly covering the clothes pulled to the basket below. Unfortunately, thats probably the only part of the process cleaning anything.The enclosure says its designed and assembled in U.S.A. and, unfortunately, speaks to our manufacturing ability. Some of the engineers Ive worked with over the years suggested areas to inspect. I was able to use my phone camera to look under the unit and noted that it is controlled by a main drive motor and a little synchronous motor with a linkage that Im guessing changes agitation direction. Both are made in China. Ive considered repairing it and just pulled the wash plate for inspection and found nothing beyond the difficulty of pulling the wash plate. Probably an issue with the drive assembly and a few hundred dollars in parts to fix. Ive also had input from someone about the cost of replacing the control board. I grew up with TV commercials of the Maytag repairman with nothing to repair in the world of reliable, American products. Its disappointing to find that is no longer the case. The low tech GE washers weve used all our lives were old and ugly when they left our house. Not defective, a few drops of oil below or worn finish but still working. It really is a disappointment to look at where we are today. It didnt have to collect samples on Mars or deliver orders in a self-driving vehicle. A reliable washer to clean dirty clothes is all we hoped for.

I bought a new refrigerator 6 weeks ago and it is not cooling or freezing anymore. I lost all my food. I spent 50 minutes on the phone to be told that the earliest they can fix it is in three days! Can you believe that? I will never buy a product from Maytag or Whirlpool again and everybody should be aware of the awful quality of their customer service!

We bought the Maytag 2000 series washer and dryer stackable set in 2012 from Home Depot. My husband was smart enough to buy an extended warranty and year after year we renewed it. Guess what?? Year after year the dang washer broke. This machine was a nightmare! Now that the drum spider is broken they will not honor our warranty but want to give us $300 and guess what? I cant find a replacement for my good working dryer. We bought this set because we live in tiny space and needed them stacked. Maytag really put us in a corner and we have no money to replace both appliances. Horrible customer service. Horrible machines. Just a horrible situation. We dont know what to do.

Product number MMV4205DS. Beautiful, felt solid. Right away when we would put in a time to cook and hit start, the thing would say Open Close Door. First we thought it was moisture, and we would wipe the seal, then lifting the door a little helped. A month might go by and we would repeat this process. I did a little research and found the microwave is known for this. After the warranty was up, it got worse. My husband put a little screwdriver in the door clamp. The plastic guard that held the door shut fell behind the opening. Mulling over whether to call for repairs or buy a new one, we decided the latter. I am buying another one just like it, because the holes in the wall will match for an easy swap and it matches my suite. This time I took out the 3 year warranty, which I will hold Maytag responsible for any more problems. They say if they come and fix it 4 times in a year they will declare it a lemon and replace. I figure this will work in my favor because the microwave lasts a year!

I have had my refrigerator freezer for 2 1/2 years. It worked fine until about 6 months ago. The vent started freezing and then water ran to bottom of freezer and freeze. If I get this fixed, I hope that will be the end of the problem. I am going to defrost it the old fashion way to see if that works. I will never buy this product again.

This will be the third repair of this refrigerator in one year, the same issue of the refrigerator warming up. Water all over the floor due to ice thaw. Also food spoilage. I want another refrigerator at this point. The Maytag repairman is definitely not lonely. He has more business than he can handle with this defective refrigerator. Terrible. Do Not Buy!!

Maytag Front load washer mah8700aww - This washer has been the biggest boat anchor of a machine. Nothing but trouble and bad parts. New motor after 18 months, water level sensor at 2 years, main control board twice now at 2 years and 4 years, and now it is showing signs of needing yet another main board. E3 trouble code plagues our home and basement. This machine has been leveled and re-leveled numerous times and still shakes like crazy... I mix my paint cans by setting them on the top... the best use for this machine. Yes it sits on a concrete floor. So not satisfied and will not ever buy another Maytag anything. There should be a negative star rating. It does not deserve even 1 star after being taken advantage of like we and thousands of others have been.

Maytag will not fix 2 major issues with new $700 Maytag dryer bought from Home Depot who takes no responsibility. They wont return it. Maytag wont replace defective dryer unless technician from totem appliances cannot fix problem. The tech ordered a control board and timer. Only installed the timer. He did not fix 2 issues. Dryer never stops at OFF. Dryer leaves damp spots on any clothing whether small or medium large load. Was told by Maytag if damp spots then its OUR problem... our ventilation. No it is your sensor. Our model is ymedc465hwo serial m820. 07331. Bought in late Oct. 2018. Two supervisors later we are being sent to tech or tech company and played games with. All I know is Maytag sells defective dryers then wont replace them or fix main issue.

#Mgt8885x500 Maytag Gemini. After oven heats up, racks fall. What should I do. This is a safety issue. Help, afraid to use oven.

This is a dishwasher purchased at Home Depot on March 25, 2012 for a rental unit... call from tenant said the dishwasher did not work. Repair person from Appliance Hospital went out today and said the control panel is out and the touch pad. Cost is over $500 to replace. I will have to replace this dishwasher BUT NOT WITH ANOTHER MAYTAG.

I will never buy anything made by Maytag again. I just bought this washer 9 months ago and the sensor broke. The repairman said I have to pay $300 for the new part and it will take 3 weeks, then the repair told me many people have this same issue and he wanted to be honest that this always happens to these washers and my best bet is to buy new... I am so sad I saved for 4 months to buy a new washer and it was a bad decision. I have learned my lesson.

The Maytag has nice features but the shelves dont allow much room to adjust them and the freezer could stand to be a bit larger but overall its a good and hard working fridge for the price. Would love if those two things could be fixed without a huge price tag.

I purchased my washing machine in July 2020 and it was broken by November. It took months without a washer before the warranty finally replaced my machine. I had the second machine less than 6 months when the water pump went out on it. They told me it would be two weeks for the repairman to come out. In the meantime my clothes were locked in the washer half full of dirty water. They told me we would have to force the lock to retrieve the clothes so they would not mold. The repairman called, never showed up, just called to ask what was wrong. Told me he would order parts and I had to wait 21 days to see if they would be able to find them. Today is day 21. I called the warranty back and was told it would be escalated and someone would call me in 4 days with a resolution. In the meantime I have spent $60 a week doing laundry for my family of 6 at the laundromat for MONTHS. Out of the 18 months have dealt with Maytag, I have spent more than 6 months at the laundromat. When I asked to be reimbursed the money I have spent they offered me a free 6 month extended warranty or a fifty dollar gift card. This product is garbage! The customer service is garbage. Dont waste your money.

Bought a Maytag bravo xl washer and dryer two years ago. Spent around 1,500 dollars. Didnt make it a year before things started going bad on them. First the lid lock on the washer broke. I got the lid lock pulled out far enough that I could drill a hole in it and tie some thread to it to pull it out when the washer was ready to lock. Today the piece of junk just quit. Not long after the junk washer started messing up the dryer starts sounding like a fork in the garbage disposal. It still works and dries the close but you hate to even turn it on because of the noise. I will never purchase anything maytag again in my life. JUNK!

I purchased a Maytag electric slide in stove, in stainless steel. The aqua clean is a joke, ran it for three cycles after cooking one roast and it does not work. Then to add insult to injury I had to get on my knees using a turkey baster to remove what was left of the two cups of water. The finish on the front is coming off. Not at all what I expected from a 1500.00 range. Poor quality. Now there is the sound of a fan running and I am not using convection.

The serial number is MDB8979SBWD. Just a few months before warranty expired the buttons were being flaky. Eventually it would not start. We brought it to the dealer because they wanted $150 to come to the house. They replaced the front panel. It lasted less than a year and stopped working again. Being out of warranty and being a technician I took off the panel and saw that there was no insulation in so the humidity would build up. The wires in the ribbon wire were corroded. I looked up the price of the panel and it was $150. The dealer wanted $150. I did not want to replace it because of the possibility that was not the only problem. We paid $400 for it on sale, (a mistake I know better than to buy stuff on close outs.) FYI to get the dealer to deal with it it would cost $300! From reading these complaints this panel seems to be a real problem with this and Maytag is not supporting this LEMON. I see a lawsuit here. Too bad Maytag is only out for profit. What is disappointing is that Maytag is owned by Whirlpool. Whirlpool has or used to have good appliances. We had a microwave that lasted 15 years and our last dishwasher that lasted 15 years. We will never buy Maytag or Whirlpool again. Maytag is junk. The dishwasher is probably ok except for the panel. Shame to get rid of it for that but unless I can bypass it that is what we will have to do. $150 is too much for a gamble and it seems that panel is a problem so it probably would not last long anyway.

We bought a maytag dishwasher three years ago. Approximately nine moths later the control panel went bad. They came and replaced it. Approximately six months later they came again and replaced it. Approximately a few months later it went bad again. I complained to Home Depot and they replaced the dishwasher. Too bad they would not change the brand. Guess what? Here we sit, not quite two years later and again the control panel went bad just past the warranty. The cost to repair almost $470.00. Paid $525.00 for the dishwasher in the first place. I regret ever leaving whirlpool. Our first very heavily used dishwasher (whirlpool) lasted 11 years no problems.

Thats right. We bought it in September 2010, and it worked fine for two years. This week, our Maytag (Model: MDB7609AWW2) simply stopped turning on. The appliance repair guy pointed out that Maytag has a horrible record which the new owners (Whirlpool) do not seem to be concerned with because even though they know these electronics are dying very quickly, the replacement parts are exactly the same (unchanged). The cost to replace the suspected failed parts is somewhere around $250. The repair guy just said, I can do it, but its going to break again. His suggestion is to shop for the cheapest dishwasher out there since even the most expensive ones fail so quickly. This particular model has a huge amount of the same complaints.

I would highly recommend you do some research on the Maytag bravos XL machines and dryer.This thing is about as good as a piece of paperweight thrown in the fire for no good of nothing. Warranty ran out but it has a 10 year warranty so I don’t understand, bought one year ago been broke down three times in that time. Speed queen all the way.

I bought model MDBM601AWB3 in October of 2009. The control panel and wiring harness burned in August of 2011 after, at the most, running twice a week. I called customer service and talked to numerous people. All said, Too bad, out of warranty. I did a quick Google and learned it is a common problem and even a fire hazard with Maytag dishwashers. My wife, who was being treated for lung cancer at the time and was very emotional, got a hold of someone in corporate and literally cried that we could not afford the $600 to fix a problem they knew it had when they sold it to us. They relented and agreed to pay for parts; we pay labor. Today, 1/10/13, the control panel is dead again. I suspect it is the same problem as all they did was replace the panel and wires. This machine has obvious dangerous design flaws that they were aware of. I find it sad that a company can screw people like this and get away with it. What recourse do we have now?

In August my GE refrigerator of 22 years bit the dust. Went to our local appliance center and purchased this unit for $2100. Have only had it a month and am so dissatisfied with the water dispenser, ice machine and doors, I want to return it. I cant wait for all the other things to go wrong with it. I dont know who the engineer was behind this but he needs to be fired. I really wish I had reviewed this refrigerator before purchasing it as I will never recommend Maytag again after reading all the bad reviews. The name Maytag used to mean something dependable and made well... Rant over.

So we purchased a whole package in sept 2014 for our newly constructed home. In Nov we received the CO and thats when everything was finally professionally installed. After its first wash the dishwasher broke and there was a flood in the house and soaked 20% of the newly installed high quality cabinets. We cleaned up everything and called Maytag to have someone inspect it to see what needs to be fixed. The gentleman came about a week or two later and said that the machine isnt worth fixing and to try to get Maytag to replace the whole machine, but he still listed all the parts that were needed to fix it. We tried calling Maytag and said what the repairman said but they said he must fix it and they will not provide a new one. So we wait for the parts and no one calls us. We follow up with Maytag and they say theyve ordered the wrong parts so it will take longer. We try calling the repair man and he doesnt call us back.Then call Maytag again and get them to call the repairman to see why he doesnt answer us. They told him to call us twice and every time he tells Maytag that hes called us and we dont pick up. So we tell Maytag hes lying, the repairman hasnt called us for weeks and Maytag doesnt give a **. And seems like this repairman is freaking lazy and doesnt want to work, even if hes paid for it. You know whats happening now? Chargeback! Thats right Maytag, screw you. When I do another house I will never buy Maytag again! Horrible service and a very defective product. I thought we were paying for quality!! They lost a customer that is faithful and doesnt mind paying extra. Hope everyone can take this into consideration before buying. I wish I wouldve seen these comments before...

I purchased the Maytag Bravos washer and dryer in September 2010, before moving to Washington. After a few months, the washer broke and had to have a repairman out twice to fix. It never would wash a blanket without stopping with error messages. He told these were notorious for problems. Now our dryer is leaking and not drying. I checked the vent hose and water and some wet lent are inside. In moving the dryer, I can hear a piece rattling around inside. From research and other posts, it sounds like its a broken pulley system inside. Maytag is junk. Customer service is terrible! I bought this unit during a veterans day sale at Lowes, using my veteran discount. Obviously, Maytag has no problem ripping off veterans or anyone else based on their horrible customer service. I will be actively posting as many negative online posts and videos about my experience on every forum and veteran site I can. They are horrible! Stay away from Maytag!

Bought a Maytag dishwasher model MDB7749AWM2 on 02 Jan 2012 with no issues whatsoever until three days ago when it stopped working altogether and after doing a series of tests I discovered that Im joining a large and growing list of owners with the same problem. I never have been a fan of digital controls due to their vulnerability to temperature and humidity conditions or high impacts for that matter. Ive owned many dishwashers of various brands for upwards of 10 years on average each. This is the first one not equipped with analog/mechanical controls. Im hoping I can still find more of that type.

This has the aqua cleaning technology, sounds real good. DOES NOT WORK! The cleaning is done by you as you nearly climb into the oven with a plastic scraper which they supply to scrape prior to the cleaning cycle. Then after you have used the distilled water in the bottom of the oven during the cleaning cycle (steam), you climb back in to wipe out the water and use something similar to a magic eraser to SCRUB the oven.Here is the real kicker....during the cleaning process, in between the glass (in the door) you develop water spots that cannot be cleaned unless you pay to have a service technician come out and tear it a part to clean it. According to Maytag THIS IS NORMAL and is proven (by their engineers without any documentation for the customers to be able to see) to be normal?? The consequence is a brand new stove will never be clean and it is the first thing you see when you come into my house. I AM EXTREMELY DISAPPOINTED!!!!

First front loader washer and love it. Saving on water, less tangling of clothes. So far they are quieter than others that I have had. The dryer is almost 10 years old and the washer less than a year. The machine I had previous to this was top loader that had to be replaced, would no longer spin.

I have Maytag refrigerator that is only 2 years & 9 months old that I am told by a service tech that it has a sealed system leak. So the unit runs it just wont get cold. I have lost all the food that was in the refrigerator & freezer and I told by Maytag that its not covered under warranty. The tech gave me a ball park quote of $600.00- $700.00 to repair the unit & I lost at lest $200.00 or more in food. I cant believe a new refrigerator wont even last 3 years & they wont fix their problem. So much for buying American made products. Whirlpool YOU SUCK & SHOULD BE ASHAMED!!!

I have always been an advocate for Maytag Appliances. Never bought anything beside Maytag. Our old Maytag refrigerator broke. Would cost too much to fix. So, we decided to buy new. We had the old white, which I was perfectly fine in buying again, however, white was super expensive. So, the salesperson persuaded us to purchase stainless steel. We got a pkg for close to $4000 all in June of 2016. Needless to say, these items have been called for repair within the 1 year warranty over half a dozen times, and have had to replace pieces that have just broken. My worst experience is the stove. I really do not like it at all. I feel the product is misleading. We wanted a self cleaning oven. It is the newest brand out there for what I consider a joke. It is the AquaLift Technology that does not clean anything. My old Maytag self cleaning oven cleaned far better than this. The same spots are in the oven. It just is worthless. I have addressed my frustration with Maytag where I was told that the oven is for the light user. Well, then you need to educate the people who sell your stuff, because I have a family I cook a lot. If this product was made for an apartment single person who does not cook then we should have been informed. Your product states Self Cleaning. Its not self cleaning!!! My frustration went up to the main office of Maytag where their resolution was to give me a discount on a new stove.What do I do with the one I have, and I was told I could sell it!!!! Really Maytag wow from a consumer that has always been a valued customer this is the level of service I get. I ended up purchasing an extended warranty on all Maytag products, because of my fear of something just breaking again. My advice to all is either buy a no named brand or buy something cheaper. Please folks if you have a family do not purchase these products. Its for people that just need a pretty display of appliances!!!

WOW! I cant believe I bought a Maytag MDB7749AWM1 Dishwasher without reading any reviews. Paid $650 for it a couple of years ago and the control panel is bad. $390 to repair it, unbelievable! Sounds like Maytag has a major customer service problem because I will NEVER BUY A MAYTAG DISHWASHER again! Spent $5000 grand on new Maytag appliances thinking they were the best to replace the outdated ones. Not the same, not sure what youre doing Maytag but youre losing a lot of loyal customers. What a shame! My old dishwasher lasted over 18 years and I didnt have any problems. 2 years? Come on!!! Same problem as the other 5000 people, someone needs a career change!

CWG3600AAS13 - I purchased this advertised as Double Oven. It is NOT - its an oven w/ broiler. The oven shuts off completely during cooking time and comes back on approx. 2-3 mins. This takes place often and loses heat. I have to adjust cooking times and oven temp to make up for the loss. This also happens when broiling. Needless to say it takes MUCH longer to broil anything. When I notified Maytag of this, they responded with it is an open door broiler. Are they serious? I have 2 dogs and 11 grandchildren - burn factor anyone? (P.S. It did not change anything.)

I purchased this washer... the Maytag Bravos. It is the worst clothes washing experience. I only use one cycle as the other cycles do not provide enough water to wet the clothes. It is a large capacity top loader. DONT DO IT!

Bravos washer is 4 years old. Started making an extreme amount of noise during the spin cycle. Had a repairman look at and showed me the bearings and area under the tub. $400 plus in damage due to bad bearings, rust to bottom of tub and surrounding area. Four years for a high-end washer is pretty bad. Needless to say, I will buy a new unit and would NEVER recommend a Maytag Bravos appliance.

Bravos MCT maytag commercial technology washer - Bought this washer a year ago. Will not complete cycles. Will not agitate. Never buy Maytag.

I bought a Maytag range (MET-8775) last year, because my wife loves to bake and wanted the double oven. The oven never did brown properly, despite trying different temperatures and cookware. So, I called the 1-800 number in the manual. I was told they would have a technician come out and check it, and they assured me it was under warranty. The technician arrived, and since it was close to the end of the warranty period, I showed him the receipt for purchase. I got another assurance that this visit was covered by the warranty, before anything was actually done. Well, he checked it out and eventually calibrated the temperature. That helped a little, but still, it doesnt brown very well. About a month later, I got an invoice from the service company that dispatched the tech telling me Maytag will not cover the visit under warranty. After a long call with Maytag (now Whirlpool, I believe), I was told that since the calibration instructions were in the manual, it wasnt covered! Well, why wasnt the thing calibrated to begin with? And your average customer is expected to have an accurate thermometer/gauge to set it and know whether the temp is off or not? Why was I told twice that it would be covered? If either the lady on the 1-800 line or the tech who came had told me this wasnt covered, I would have argued a case right then. As it turned out, I had no choice but to get billed for something I was assured was covered. And as I said, it still doesnt brown right; and we had tried different temperatures before. We are preparing a major kitchen remodel, and its hard to believe that Maytag/Whirlpool would so thoroughly piss off a customer and potential future customer over an $80.00 service call.

Contacted their customer service by phone and email numerous times...sent photos. They did nothing on a major issue,,three year old washer..now junk. Side of washer is rusting out the metal housing on washer is compromised.

I bought a Maytag Bravo Series 300 washer and dryer for $2,000. The dryer is fine, so far, but the washer is dead. I have not received any answers from Maytag and the product is already outside of its warranty. I only had it for two years.

We purchased a Maytag front-load washer and dryer in October 2010. In March 2011, all bearings and the drum needed replacement. In July 2011, the pump needed service and now in Sept 2011, we were told a new drum and bearings are needed again. The washer is still under warranty by Maytag. We contacted Maytag to ask for an exchange or a refund but we were told that it wasnt possible.

Thinking that the Neptune fiasco was over, I happily bought into the sick company and got burnt 3 times for all 3 purchases. The Gemini range with dual ovens: the controller clock with all relays and electronic package is dying, leaving me with no ovens, or slow heating and an alarm in the middle of the night. Now, even the burners are not working properly. Junk at any price, and I paid $2,400. Not 5 years old and repaired several times under warranty; all were electrical failures.The fridge is another failure. Apparently the Freon is leaking out. It is unrepairable and it was typical of these from what the service guy said, not 5 years old. It was repaired once, leaking on floor. Apparently, it was a kinked drain hose. The dishwasher was one year old and it caught fire when the dial was turned while the machine was running. The 4th machine, an over the range microwave, is still running… although from day one it sucks so much power on the dedicated line that it dims the lights in the microwave as it starts up and each time, the magnetron energizes. I am just waiting for it to fail too. Can you say never and mean it? There was no goodwill offered. “So sad” and “too bad” is the common line. Nothing will last more than 5 years if you listen to sales people at Maytag - junk. There was no help from the corporate office. Nothing I can do for you. Junk, junk, junk.

I saw something on your website about Maytag Neptune class action suit back in late 2005. I have owned one, never was notified of the settlement, and saw this since I have a mildew problem also in my washer. They are not willing to do anything about the repair on my machine, but send out someone and make me pay for it. Since I bought it in 2002, I would want to know why was I not included in the repairs and why wont they honor me in this since I am the machines original owner. Help, I worry that I am not having clean clothes and it is contributing to illness due to mold spores!

Maytag Bravo XL top load water saver - Purchased this two years ago. This is the worst washer I have spent my hard earned money on. It has ripped clothes, always leaves a lint and soap film on the cloths. We have to re-rinse two to three times especially on black and brown dark clothes. I have raised 7 kids. In the past Maytag has always been the best. I spent a bundle for the matching set and we have to suck it up and buy another set. We wouldnt feel right selling this set to anyone knowing the faulty sales pitch we were mislead into buying this brand. Purchased from Sears. Sears chose not to offer any help in replacing with a different brand.

We bought a Maytag refrigerator (single-door) with a top-loading freezer that failed after four years. The freezer began to ice up and two repairmen from the company that does the extended warranty repairs in the Ottawa area were unable to figure out the problem. After the second visit, the freezer iced up again and the thermostat appeared to be failing. Even though we had an extended warranty, we just gave up and went to a different dealer to buy a new refrigerator that could be delivered within three days - and it wasnt a Maytag or any other of Whirlpools brands. If youre thinking of buying a Maytag refrigerator, you should reconsider. In fact, you should twice before buying anything made by Whirlpool.

Maytag washer MVWC565FW - Clothes do not wash. They just get pushed around and the soap scum is left on the clothes even with the water at the highest level. I bought the washer override lid switch at a appliance parts store just to observe the washer cycles. The washer did not wash the clothes. I took the washer back. I like Maytag products but this washer has to be engineered.

I purchased all new appliances and decided to go with Maytag. My Maytag Refrigerator model MFI2569VEM after 12 months, just after the warranty expired, started leaking all over my kitchen floor. I called Maytag and all they told me was there is no recall on this model and there was nothing they could tell me over the phone. I purchased an extended warranty and that is a whole other problem to get someone out. They said to check the freezer problem I need to call when the leak was occurring, so they could see what is happening. So basically, I need to leave water on my kitchen floor so they could see what is happening. Who hires these people?

The worst wash machine Ive ever used. It doesnt clean clothes well. It constantly had error codes. Im constantly having to unplug and reset the machine and 4 times out of five it will NOT restart. Not to mention it stinks worse than my sewer. I have to run the refresh cycle every four to eight loads. Ive owned this machine three years. And it has been three years too long. I will go back to a ringer washer or a wash board and have better results.

I owned my double oven Maytag Gemini for 14 months and I was absolutely satisfied with it. I was running a cleaning mode on the bottom oven and the lock froze. I have tried everything with it to unfreeze it, including the suggestions offered on the internet. I havent been able to do it on my own and I cannot afford to hire a repairman. I called the help line offered by Maytag (after waiting for 32 minutes), the representative actually laughed at me when he found out it was past the 12-month warranty. Though this laugh may be unusual, I feel it is very indicative of the way Maytag handles any problems; Maytag doesnt stand behind their items, they are now built shoddily and they could really care less about retaining their customer base.

Like everyone else got that French door fridge and was also duped on that 1 yr warranty - a 95 dollar repair visit for a 485 repair job on a 1200 dollar purchase. Shame on them. Im gonna fix my new floor and replace that frozen bottom, leaking on the left, non-working ice maker 2 yr old refrigerator. Very disappointed with the whole thing and sorry for all of our losses.

Bravos x - Ok so I was checking on my washing machine balance which is off. I came across the reviews and find how horrible the machine is! Grinding at last cycle, and not wringing out clothes on some loads. I thought grinding and wringing out was to be that way since it did it from day one. I thought I just needed to adjust clothes to wring out. Balance was taking out some clothes but it was put in properly. Boy was I wrong. Im so pissed after reading all your reviews. Im going to contact my daughters who works for attorneys about false advertisement and selling something they know is crap.

Shortly after purchasing my Maytag refrigerator had to pay for a new motor in the ice maker. The cover for the lower large food tray broke. Now approx. 4 years later am getting ice build-up on the bottom of the lower freezer unit, about one-half inch thick. It is enough so the freezer door wont seal when it closes and the inside builds up with frost. Not happy with Maytag or this refrigerator.

Side by side refrigerator model #msd255oveu01. I bought this refrigerator Apr. 2011... The 1st year, the ice kept sticking in machine or freezing up. Now they have had to replace the modules 3 times. Once fall of 2012 and and again yesterday, 3/19/14 and they had to come back today to replace that one. I have called Maytag and they wont stand behind it since the warranty is over. I have told them that this is an ongoing thing with the ice maker and I have had to have it serviced ever since I have bought it. I told them from the git go that the ice maker needed replace. The ice dispenser also drops an ice cube on the floor on occasion and if I use crushed ice it jams up. This product is defective and is not a good product.

Purchased in 08 for a second home, we visit every other weekend mostly in summer. I have never been pleased with the set really. It takes too long to wash/dry, clothes get tangled, dryer goes off on first buzzer, wrinkled and now, the control panel has gone out on washer and they say it is approximately $500 to fix. I have probably used it 20 times a year. I have Maytag in Lex, which I have had for 15 years, that is 100% all the way around better.

Because it is the high efficiency model, need to leave the lid open so interior will dry and not smell musty. Also, recommend using a washer cleaner such as Affresh or Tide tablet every now and then. But works great!

Both my washer and dryer are Maytag. Dryer element shorted out but was still under warranty so was fixed. Washer is very loud and now makes a rattling sound. Every so often it will hang in the middle of a cycle and the lid wont open until I unplug it.

We purchased a Maytag Top Load 5.4 cu ft efficiency washing machine. May 2019. It was making a funny noise already mid October and we had 8 parts replaced. After that it completely stopped working. We have been without a working washing machine for 2 months now. The technician has been to our house 4 times. When he came on Dec 31st to replace the mother board, that didnt solve the problem. He says the washing machine can not be repaired. We have been fighting with Maytag Canada and Lowes since the beginning of December. Neither company cares. We will never own another Maytag product. The company are crooks.

It took about a year for the problem, which turns out to be an extremely common problem, to start. The build up of water in the freezer due to the clogging drain. Maytag needs to step up for the consumers that purchased their defective product. I have cleared the ice and tried to clear the drain three times only to have the problem return. I refuse to pay someone $300 or more to repair this. This is crazy and unfair!

Softener container is clogging up with softener. Worse, the drain in the fridge has frozen up twice and now again I am having to pay someone to clean it out. A pool of water accumulates in front of the fridge where the ice melts. Disgusting in new appliances.

I purchased my Bravos (ecoconserve) washing machine in 8/2013 from hhgreg. The problem I have is this grinding noise with the spin cycle. So I unplug the machine because the lock lid light is flashing and wont unlock unless I unplug the machine. I grew up on Maytag so that was the reason I purchased this machine but never again. I am so disappointed in this product. :(

We have had 2 Maytag dishwashers only last less than 2 years. Since we can only have a portable because of owning an older home the expense is too much anymore. We also had a Maytag Neptune clothes washer last only 2 1/2 years. We had always respected Maytag and trusted them. That trust is gone. It is too expensive to buy and lose them after barely 1 1/2 years. We had a Kenmore that lasted 23 years. I dont know what company to trust anymore. The one we just had quit working a month ago was purchased October 3013. Maytag dishwasher Model #MCD4809PAW2 Serial #F34003436.

We bought a Maytag Neptune Washer and dryer package from Home Depot in 2004 and had nothing but problems ever since. Such things as washer had mold constantly. Also, clothes seemed to have a foul odor after washing. The dryer always seemed to have to be ran twice to get clothes dry.