I bought a Maytag refrigerator, model MBF 2256 KEQ2, two and a half years ago. Now the cooling coils are freezing up. I checked heater and thermostat for continuity and they were okay so the only thing left was the timer control circuit. On the earlier models, the timer control circuit is controlled by a Timer Motor or an Adaptive Defrost Timer which is separate from the main Electronic Control Board and much less expensive. On later models (including mine), the timer control circuit is incorporated into the main Electronic Control Board so if your automatic defrost quits working, more than likely you will have to replace the main board. I did not purchase an extended warranty because I believe they are useless from past experience. I bought the part on Amazon.com, received it in four days and replaced it myself for a cost of $78. This part costs $110 to $118 at Sears or a Maytag dealer.

Centennial commercial tech. washer - We purchased this piece of junk in Sept 2013, and had to have a repairman twice before it was six weeks in my home. I wrote several letters but the only thing that I received were applications for insurance to cover repairs. I should have received a replacement as it was bad from day one, but Maytag doesnt replace!!! Its been semi-reliable for the past several months, until early this year. It started jerking when it changed cycles, sounding as if the drum was hitting really hard against the sides. It has continued to do that regularly; now it wont function on the cycle its set on. It wont spin, sometimes the lid lock wont work. It starts filling when it should be draining. This evening, it stayed in the rinse cycle for 40 minutes and when I realized it was still rinsing I had to unplug it to get it stopped. It goes on and on, (and so could I out of frustration). The good name of Maytag has turned to trash, and when it leaves my home, no more Maytags!!! PS. The dryer we got with it takes at least 1 1/2 full cycles to dry a load, and since I couldnt get it to spin properly, Ill be lucky to get this last load dry in 2 to 2 1/2 cycles.

The serial number is MDB8979SBWD. Just a few months before warranty expired the buttons were being flaky. Eventually it would not start. We brought it to the dealer because they wanted $150 to come to the house. They replaced the front panel. It lasted less than a year and stopped working again. Being out of warranty and being a technician I took off the panel and saw that there was no insulation in so the humidity would build up. The wires in the ribbon wire were corroded. I looked up the price of the panel and it was $150. The dealer wanted $150. I did not want to replace it because of the possibility that was not the only problem. We paid $400 for it on sale, (a mistake I know better than to buy stuff on close outs.) FYI to get the dealer to deal with it it would cost $300! From reading these complaints this panel seems to be a real problem with this and Maytag is not supporting this LEMON. I see a lawsuit here. Too bad Maytag is only out for profit. What is disappointing is that Maytag is owned by Whirlpool. Whirlpool has or used to have good appliances. We had a microwave that lasted 15 years and our last dishwasher that lasted 15 years. We will never buy Maytag or Whirlpool again. Maytag is junk. The dishwasher is probably ok except for the panel. Shame to get rid of it for that but unless I can bypass it that is what we will have to do. $150 is too much for a gamble and it seems that panel is a problem so it probably would not last long anyway.

Dryers been installed for 3 months, 3 service calls to date. Heat unit failure. 1st service call no show, no call. 2nd service call fixed the problem 50%, the dryer would heat on timed dry but no other modes. A week after that call heat unit failed again on all modes. Awaiting 3rd service call. Customer Service Department at Whirlpool Canada could care less. Avoid this product, Maytag 2000 series dryer - do not buy.

The refrigerator had to have repairs in first year. Maytag was aware of freezer issues and reluctantly finally replaced the parts. I had to argue with repairman because he tried to tell me that the freezer was too full.

I purchased a new Maytag dishwasher model MDB7609AWB1 approximately 2yrs ago from Sears. We purchased quite a few new appliances from them and they are always helpful. Within the first year, right after the warranty was up, it stopped working. No lights on the power panel. I called Sears, out of warranty, sorry. Said they would give me a deal on the repair. Sears came out, replaced the computer. $230.00. 6 months later, it stops working again. I go on line to look up these models and sure enough a lot of people are having the same issues. I did some of the checks that they said to do and found my plastic door latch was broken. A little plastic arm that actuates the switches broke. Should have been made of metal. I replace it myself, very easy, by the way. So I figure, in another 8 months it will prob break again. They run anywhere from $19.00-$30.00. 2 days ago power panel and light, not working again. I called Sears and asked them if they were having issues with the power panels that this was the second time in less than 2 years, and if there were any recalls, they said no. I guess they dont follow their reviews, but according to google reviews, its a major problem with most of them. Maytag, Whirlpool, and Amanda. Ordered a new panel today, again they are $141 from Sears but if you shop, you can get a new one for less than $85.00. If you have any kind of mechanical skills, you can replace it in less than 20 mins. It just seems to me that this big companies have let their quality control go and are more concerned about the profit. There should be a recall on these. Do Not buy a Maytag/Whirlpool dishwasher, they are total junk. Sorry Maytag, you lost another customer.

Maytag Model # MMV4205DS - First Maytag microwave lasted just over a year before it quit. Replaced with same model to avoid install hassle and 1 year and 4 months later got the dreaded open and close door message. Read so many horror stories about repair service for Maytag that I decided not to bother and purchased a GE. I will never ever, ever buy anything Maytag ever again...

We have a 3 year old washer dryer. The wash stopped working so we called Maytag directly to have their repair person come look at their product. Little did we know that they sub contract repair to local companies I could have contacted myself. After being told the authorized dealer was Maytag I soon found out it was not a Maytag employee. The man who came has no idea what is wrong and is guessing at issues. Once a installed part is not the cause he wants to try something else but we have to pay for him to trial and error.We have spent hundreds of dollars and yet our washer is still broken. We have decided to go buy another washer as this is our cheaper option (it will not be a Maytag or Whirlpool). When I tried to talk to ** (Maytag manager who lied on the phone to me and was very rude) manager I was talking to refused and told I had to file my complaint with her co-work. I have never heard of this! We will never buy Maytag or Whirlpool (same company) as our dishwasher after 1 year 3 months old needed a new motor total repair $450.00. Their products break down early.

My Maytag french door has worked steadily for 12 + years. It’s a basic model, ice maker in freezer. No door dispensers or electronics. I would buy it again.

It was alright for a while. Then it started ripping up my clothes. The machine is not overloaded, enough water has been added but, when I take the clothes out they are torn. Not a good experience. I have seen several reviews on the Centennials, none of them good. What is the problem. I am hoping my experience gets resolved.

The dishwasher is very stylish and looks great in our kitchen. I do wish there was a small knife drawer in top. It cleans very well and is super quiet. I would highly recommend this dishwasher, good value.

I purchased the gas stove in June of 2012 from Home Depot, along with a Maytag microwave (Model MGR7662WB4). Home Depot installed both items. After trying to reach into the microwave about the stove, the knob would turn itself on with me brushing up against it. This happened several times, and one time the flame shot up and I almost got burned. The last time it happened, I did not realize that the knob was turned very slightly and gas was coming out of the burner for several hours. If it were not for a friend stopping over, I would not have considered the odor being from the stove. I assumed that the drains were probably backed up and started to add cleaners to the toilet bowls. I had to open the windows for several hours to get the smell out. So I called customer service 2 times. The first person said I would have to pay for the call if the problem was not Maytag and I said, “Forget it.” Then I went into Home Depot and the salesperson in there gave me another number to call for service. They came last Friday and said that he had seen at least 10-15 calls about this and since the unit was working as designed and no recalls, there was nothing they could do. “Just wait and see if a recall would be put into place and I would be on the list to fix it. In the meantime just keep the knobs off (which I was doing already out of fear).” My sister just bought a Whirlpool gas range this summer as well and asked if I could try her knob and it worked perfectly. Again I called CS and was told they could not send me those at no charge and that it would cancel out the warranty. So I asked her what I have to do before I or someone else gets injured and she said that until there was a recall, there was nothing they could do. I told her I was going to contact Consumer Report as well as Pam Zekman on Channel 2 news in Chicago. End of story; I still have the problem and no knobs on the new stove. Anything you can do to help please contact me, and thank you in advance.

Maytag washing machine exploded sending glass shrapnel everywhere. At this point I believe Maytag should replace the machine. I appreciate after MANY hours on hold and being transferred that you are sending a repair person out, but there is tiny glass shrapnel all over inside. This is crazy, and a MAJOR safety concern.??? Update - can’t find parts or an eta. Replace the machine!

I feel its kind of cheap. The interior is all plastic which doesnt look shiny and clean as it use to be when it was new. Not efficient in cleaning. Can see still dirt spots in some of the washed dishes.

Maytag used to make a great laundry machine. The barrel of the Bravos XL machine is very deep, and it is difficult to reach the bottom of the machine to get clothes out. My biggest complaint is that the clothes dont get clean; there is not enough water filling the machine to clean the clothes. The clothes get wet, but there is no agitator, and the water isnt deep enough to suspend the dirt and wash it away, even on the deep wash setting. There is also a lot of lint left on the clothes that cant rinse off. Why is the barrel of the machine so deep if it only fills up 1/6 of the height? I had great hopes, but I really regret buying it.

Maytag HE Top Loader Washing Machine: I have regretted buying this piece of garbage since my first wash. This washing machine is complete waste of money and a piece of garbage. The Auto Sensing doesnt work and doesnt cover the clothes with enough water. When the deep water wash is chosen the clothes just float around but the agitator doesnt get them clean. Dont waste your money hoping it will work, because it wont. Maytag used to signify quality that is no longer the case. I am going to also give a bad review to the place I purchased this piece of garbage because all stores need to discontinue selling this junk.

Weve had our Maytag dishwasher for less than 4 years when the control panel quit. The repairman came today. He was here 10 minutes and it cost us half as much as a new dishwasher. Its just the two of us and we use the dishwasher once every 4-5 days. Almost laughed when the repairman said the part and labor was under warranty for 90 days! There is no quality control anymore. Just greed.

Maytag Bravos Quiet Series 300 - Just DONT BUY this junk. We bought the washer and dryer set from Home Depot in 2011 and have had nothing but trouble with the washer. Three times small objects like dimes, pennies and nickels got past the agitator into the drain pump which has been replaced twice. Beneath the agitator we even found a few missing socks. Today after a visit to the Laundromat, we bought a Samsung with a 5 year extended warranty. If that doesnt work it will be an old fashioned Speed Queen next. We will never buy anything Maytag again and I hope to influence everyone we meet about them. I cant wait to throw it into the city landfill for recycle dog food cans.

We purchased our Maytag Bravos just under two years ago. Over the past month or so, we noticed the spin cycle was getting louder and louder. Today we had the service man come out. He informed us that our 2-year-old machine will require new bearings and a new basket, which equates to over $700 in repairs. The repairman said he has seen more and more of this with these high efficiency washers. He suggested that anyone buying these new washers be sure to buy the extended warranty.I for one am completely disappointed that one can spend that much money for a washer with a two-year shelf life. I personally think this is planned obsolescence created by the manufacturers. The serviceman also said the LG versions of these washers have a large increase in electronic problems. Be warned, we have very few choices these days so buyers beware.

My Bravos XL is worthless!!! This lack of agitator design is totally ineffective. Dark clothes come out with white powder on them and I use the liquid detergent. Whites I soak with detergent and bleach then full wash cycle. Still stains on dish towels and socks. Never had a problem with the old agitator Maytag. And yes the wrinkle free cycle creates wrinkles. Deep water wash is only cycle that even comes close to cleaning and its far from perfect. Horrible waste of money, buyers beware!!! I thought all those negative reviews were overblown and since I couldnt find a large enough machine with an agitator, I ignored warnings and bought this garbage. Matching dryer is fine.

Maytag Bravos XL - I am having the same problem as everyone else with this washer. My clothes do not get clean and they smell. Maytag advertises tumbling, rubbing action to get clothes clean but my washer does neither. The clothes lay in the bottom of the tub and never move except when in the spin cycle. I am going to file a complaint with Maytag and if they do not refund my money am going to file a DTPA claim against them for false, misleading and deceptive advertisement. They will have to pay up to three (3) times the purchase price of the washer. Maybe everyone else should consider the same.

I bought a Maytag washer and dryer about 2 years ago. I’m on my second washing machine (one was replaced from Lowe’s not Maytag). The second washer has now gone out! First it was the lid lock and now who knows! The repairman can’t even fix it. Biggest piece of crap, stay clear!! My first set lasted 25 years. Poor quality workmanship and customer service!!

I purchase my Maytag Bravos washer from Sears in May 2011. In February of 2014, I started to get the UL message, meaning unbalanced load. I would re distribute the clothes and sometimes that did the trick and others not so much. Now every load comes up UL. I tried putting the machine on the drain and spin cycle to at least get the clothes a little bit drier but the UL message still appears and the clothes are still soaking wet. I lifted the washer up and there is an oil/grease type spin pattern under the washing machine. I called Maytag today (which is now Whirlpool I guess) as the washer has a 10 year warranty on the drum and motor. I was told a service call is $129. When I mentioned that I had Googled the product and saw many reviews with the same exact problem, she stated the Bravos has no common complaints. From what Ive read, it seems to me it would be more cost effective to go out and buy a new washing machine and it obviously wont be another Maytag or Whirlpool.

My Maytag MDB7609AWW2 dishwasher was purchased on 1/2010. Last month, the control board only worked on the right side of the panel and the dishwasher would not run. I called Maytag to see if this was a typical issue with the washer, which they denied. I ordered and replaced the control panel but this did not help. After reading all these posts, I do not think Maytag is being honest with their customers. Also, it looks like even if I am able to fix this issue, it is likely to repeat. I think I will cut my losses now and buy a different brand of dishwasher. I will never buy a Maytag again.

I have owned three different Maytag washer/dryer sets. The reason for so many? Selling the set with the house upon moving. I kept my last set which is Bravo. I love Maytag for their features, their dependability, their reputation. I have never had repairs on any of them. Totally awesome! My second set had a neat feature of a drying rack where you could place a sweater or shoes and no tumbling. Sorry I sold that set w/ the house. I am very pleased w/ my present set of Bravo. No agitator. A coworker also bought this set. Maytag is the best!

I bought a new Maytag dishwasher installed by East Town Appliance in Wautoma, Wisc. They installed it and ran a full wash cycle and it worked fine. After they were finished, I got all my glasses out and put in their dishwasher all excited to get them clean and sparkling. I started the dishwasher, put on a coat to check my birdfeeders on the deck where I was standing in front of the patio door. I heard water running suddenly. Turning around to see water gushing out of the bottom of the dishwasher. I called East Town back and had the installers return immediately. The pump was stuck open. I called Maytag about what happened and they said they wouldnt pay for the floor damage because it was already installed and to call my insurance company which I did. They went after Maytag and won but I had to pay $500 insurance deductible. I will NEVER buy anything by Maytag again.

I purchased a whole stainless steel kitchen from Lowes and purchased all Maytag products because of the so called quality of Maytag. First we had to return the microwave because it was dented badly. We then notified Lowes that the door on the refrigerator cold cut drawer falls off when opening the drawer. Service man said he would send a new door. Same problem. You can clearly see that the drawer and the refrigerator frame is deformed. Maytag says that the warranty does not cover cosmetics. The range has a aqua lift self-cleaning technology that simply sucks. The oven does not clean! I recommend that no one ever buy Maytag products. They are the worst! I should not have listened to the salesman and bought what I originally wanted - SAMSUNG!!!

Model# MVWB850WQ0, Serial# CY4070329, Type 580-02. Bought this Commercial Technology washer 2-1/2 years ago thinking the commercial model would be heavy duty. It was only heavy on the wallet. The washer started to emit a loud roaring sound two weeks ago that never happened before. It happens on spin cycle. We cant even have a normal conversation in the house. After reading similar problems and outrageous cost to repair, Im leaning to look for a replacement without the Maytag label. My 10+ year old Sears Kenmore didnt have any problems. My mistake was to replace it with a more efficient washer. I guess New+Efficient doesnt equal long lasting for Maytag. You would think a major manufacturer would put in heavy duty bearings in a washing machine. Heck, maybe the bearings are heavy duty but design shortens bearing life. Enough time spent on Maytag. Stay away!

Maytag French door Bottom Mount Model # MFT2976AEW02 - Purchased this model refrigerator in late 2013. Had minor problems with ice maker for last 6 months, not have freezer problems, as the bottom freezer is not keeping food frozen. Called repairman today. He ran 64 checks on refrigerator, said to keep eye on problem and he will re check in 24 hours. Called private company, Maytag in Latrobe. They referred us to the Maytag repairman. We will keep you posted. We moved all of our frozen food to a downstairs older freezer for safekeeping. Keep checking, we will update.

I had the old style machine and finally it gave out and I bought an LG HE Large capacity. It was a well I can print it here but kept the machine for 5 years and gave it away. I bought a new Bravo Maytag set 5.2 with the old style agitator thinking I was going to get a great machine and NO. These new machines do not use enough water in the load sensing and clothes on top never get in the water. They come out with soap stains even with a double rinse. And no I am not using too much soap! My old machine had small medium and large load settings plus you could add more water if needed. Way better machine.The techs are trained to tell you this is how the machines work and there is nothing wrong with them. Finally an honest tech told me they are having all sorts of complaints and problems. If all you wash is bedding and dress clothes you get by but if you really have soiled clothes you have to do a lot of prep and then stop in the middle of the wash cycle and rotate your clothes manually! Total BS for 8-900 dollar machines. Do yourself a favor and buy a front load. At least the clothes will get flopped in and out of the water and hopefully rotate so they actually get clean. That is what I am going to try before I go back to the old scrub board and tub!

I also bought a Maytag Neptune MAH5500BWW and matching dryer model #MDG5500AWW in 2001 and within a month, I called Sears and Maytag. I told them about the terrible odor and mold growing. The repairman said it is normal and told me to use Tide detergent once every two weeks. The dryer had a major breakdown and I had to buy a whole header with all the electrical components. I too bought the brand name Maytag due to a good reputation that Maytag had. I never received a recall notice or anything from Maytag. I will never buy Maytag products again. I found out from a salesperson at Sears that Maytag was sold to Whirlpool. The salesperson said the reviews are terrible for Maytag products especially for my models. I will never buy from Sears, etc. What can you do for me? Maytag and Whirlpool need to take their responsibility for their products! I am truly lucky I did not buy a plane from them. I and a lot of people would be dead.

I bought a Maytag washer in June and its the worst washer I have ever had. It has been 15 yrs since I had to buy a washer. My last washer was a Kenmore which was great. The Maytag does not have a water control knob. It has auto sensing which is crazy. I know how much water I need to wash my clothes. The water sensing barely puts water over the top of the clothes which is not what I need. My husband works in the oil field and gets oily and dirty. The next issue is the agitator that agitates the clothes. This one is a joke. The agitator starts agitating the clothes before the water is over the clothes and then when it needs to agitate it does a poor job. I am so unhappy with my machine that I am getting rid of it and looking for an old type washer. Evidently you made this washer for white collar people who do not get dirty. This is definitely not a washer for people who have dirty laundry. I am so disappointed with Maytag. I thought this was a good brand.

We purchased the MMV4205DS over the range microwave in June of 2015 & installed it in July the same year. We purchased the matching range & a dishwasher at the same time as they were running a promo of $150 rebate if all 3 were purchased. They denied us of $50 of the rebate & stated that all of the paperwork was not submitted on time. We received rebates on 2 of the appliances & paperwork for all. 3 were in the same mailing. Hmmm. We were told a 3rd party handles their rebate program. So much for taking ownership. Yesterday the door open message appeared on the control panel of the microwave & now there is nothing; no light, no fan--completely dead. So much for buying American. Maytag does not see that this is a problem? Do NOT buy Maytag!!!

I have had my washer and dryer for about 5 years. After a couple of years, I noticed my washer would fill and stop. When I go to put clothes in the dryer, it’s still filled with water... very inconvenient! I have to open and close it and then it continues. The dial doesnt work properly! The delicate cycle hardly works... that started after about a year. It just freezes up and stops. I have to open and close it. It does not rinse right, leaves a film on dark clothes, and I have to rinse again; I do not over fill it either. Sometimes it does smell a little mildew.The dryer knob does not work properly. I set my setting and pull the knob out, and it doesnt come on. I have to do it several times or change the setting or put it on 30 minutes only... very frustrating! I never had these problems with my Kenmores! I wish I did not switch brands. These things should work properly. I realize washers and dryers dont last like they used to, but come on! They also cost so much more than they used to. I wont do this again. I will do more research as to what is a good product. Too bad!

Maytag Bravos XL - This is the worst product I have ever owned! I purchased a Maytag because when my husband and I were married 29 years ago we bought a Maytag washer and dryer and still using the dryer. However we lost the washer and had to replace it. Worst mistake ever!!! Within a year a circuit board went out (they replaced but I was advised I needed an extended warranty which I do have) and was told by the technician that this model was junk! I called Maytag and expressed my great disappointment and all I was told is we document customers input. I then ask ok so what are you going to do about it? And I did not get a response. I asked for a different model but was declined. As you can see it is rusting at only a 1.5 years old and tearing up my clothes. It destroyed a doily that belonged to my late mother. Maytag used to have integrity in their product but not anymore. Not only all of these issues but I have to wash clothes twice and they still are not clean. Plus they have a dirt film on them and yes I used THE detergent!!

The only time one can get enough water into the washer to actually get ALL the items wet (or even damp) is to put it on BULKY sheets or HAND wash settings. That is true for any size load whether it be 1 item or 10 items. I prefer being able to get ALL the water I need first, then put in the clothes, then soap, but thats not allowed. First soap, then items, then a bit of water only after you close the lid. They like to say that the spinout dries them which is why they arent damp - but that is a lie when you can smell and see the dirt. I want my OLD STYLE back!

We purchased a Maytag Bravo washing machine and dryer from Home Depot so needless to say, it was not an inexpensive purchase. I absolutely will NEVER purchase another Maytag ANYTHING! The washer will not spin and when it does, it sounds like it is coming through the washroom doors. The heating element has had to be replaced in the dryer and has always had a sour smell inside. I have nothing nice to say about these products and would absolutely NOT recommend them to even my worst enemy!

Bravos x - Ok so I was checking on my washing machine balance which is off. I came across the reviews and find how horrible the machine is! Grinding at last cycle, and not wringing out clothes on some loads. I thought grinding and wringing out was to be that way since it did it from day one. I thought I just needed to adjust clothes to wring out. Balance was taking out some clothes but it was put in properly. Boy was I wrong. Im so pissed after reading all your reviews. Im going to contact my daughters who works for attorneys about false advertisement and selling something they know is crap.

Maytag XL Washer - My new machine is awful as well. Black clothes are smeared with I dont know what... looks like dirt. The wrinkle cycle doesnt work and the bedding cycle forget. Wish I read reviews... silly me.

Bought a Maytag dishwasher model MDB7749AWM2 on 02 Jan 2012 with no issues whatsoever until three days ago when it stopped working altogether and after doing a series of tests I discovered that Im joining a large and growing list of owners with the same problem. I never have been a fan of digital controls due to their vulnerability to temperature and humidity conditions or high impacts for that matter. Ive owned many dishwashers of various brands for upwards of 10 years on average each. This is the first one not equipped with analog/mechanical controls. Im hoping I can still find more of that type.

Maytag dishwasher quit working 3 years old. No power. Control panel dead. Piece of junk product.

At first the Maytag Bravos XL top load washing machine met all me expectations. After 3 yrs. the top where you load bleach and fabric softener began to rust. This is not covered under warranty. My last washer was a Whirlpool and had it 15 year and never had that issue. So it cant be from the water, just poor workmanship. Very disappointed. Now my lid came loose and is ready to fall off. Would not recommend.

I bought a fridge from Home Depot. It was on sale and not a Maytag. Somehow they delivered a Maytag. I am over-the-top happy with my fridge. It keep things cold. It is roomy, It has separate temp controls for the freezer and fridge. The bright LED lighting is wonderful. It is energy efficient. It is easy to move around when I need to clean under it. It was delivered right away.

Maytag Dishwasher model MDBH989AWB3. The dishwasher was purchased at Home Depot March 19, 2010 in Hollywood, FL; delivered to our new home April 16, 2010 in Brunswick, ME. My complaint is the exact same complaint as the previous 28 complaints! I think the reason our unit worked for 6 yrs is because it was in use only 6 months a year. My experience: you make your selection, two lights come on, you press start, but nothing happens. You think this is a simple repair. You read the manual and try their troubleshooting advice, but to no avail. When you contact the company, they tell you that this is going to be an expensive repair, probably over $500. You contact Home Depot who want nothing to do with you or your dead dishwasher. Their advice: contact the Maytag company. You contact local appliance repairmen and they will repair it at a cost of over $500. You offer the unit to the repairman for free; he declines. He suggests you check the online Consumer Affairs site. It is on that site that you realize the dead dishwasher belongs where one brings other dead things: the dump. I will NEVER buy another Maytag product. I would suggest no one else does either, unless you want to practice your skills in dealing with frustration or you want to throw $693.40 to the wind and watch it flit away helplessly. Thank you for reading this.

I, too, am absolutely done with ANYthing Maytag. We purchased our Maytag microwave model MMV4205DS-1 in January of 2016. Within the first year we experienced occasional open/close door issues due to the faulty door latch switches. Now it happens virtually all of the time. The ten year warranty is a joke; it is just a come-on designed to deliver a false sense of security that Maytag will indeed stand behind their worthless products when in fact they wont. I am so disgusted with them.

All I can say is what a mistake. Had a front loader that always smelled and had mold around rubber gasket in door. So, wanted a top loader this time after old GE died. Unbelievable, not enough water to clean clothing. Clothing comes out with some dry spots. And the worse thing is washing black items, tiny particles on black pants, shirts, etc. Think is lint not soap but not sure. You have to rub all over the clothing to try and remove. This washer is 8 months old and I have cleaned it with baking soda and vinegar mixture thinking this would help, it doesnt. The spin cycle sounds like a rocket ship taking off. Lots of banging noises during operation also. I have invested a lot of money thinking Maytag is rated high. It is a pretty grey color with glass top. Well I was fooled, not only the saying looks arent everything for people but its true for washing machines. I have gotten multiple mail from co. wanting me to get extended warranty. Think I will, usually dont, cause I think it wont be reliable. Wish I had my washer from the 70s and 80s. Plain old wringer that got things clean. Just put black pants in dryer on very low heat taken out damp cause I dont dry a lot of my clothing. This seems to have helped to remove stains (soap)/ lint. but, talk about wrinkles, oh boy, this machine has that spin cycle going 100 miles a minute. And if you pick a lower spin speed things come out wet. I actually can say I hate this Maytag Bravo. Things dont come out clean, wrinkles beyond control, very loud. Please folks check out your sites on the internet before buying Maytag.

This washer has been the biggest disappointment of any appliance I have ever bought. Purchased 12/2012 and immediately disliked it but thought I needed to get used to the new style since my previous machine operated for 23 yrs! It is loud and does not clean as effectively as my last machine. It stays in the Sensing mode for 15 mins or longer. Rarely will it spin as it should. Most loads, after the sensing stops and the lights go out, I have to move the dial to Drain/Spin, wait for it to sense again and then maybe it will spin. If this doesnt work I have to unplug the machine to allow it to reset. I called Maytag and was told there are no known issues with the machine. I google this model and find many customers have had a similar problem.

I bought a new Maytag washer 1 year ago. It does not do a good job of washing the clothes. I have tried to contact customer service but what a waste of time that has been. I would never buy another MAYTAG washer again. This is after owning an older style Maytag for 25 years that I never had one problem with until it wore out. They are now junk. I bought at Leons. Would be very careful of buying there again as they were also no help with this washer not working properly.

Purchased a new Maytag dishwasher three years ago. After having it for one year the panel box no longer worked. Had to pay $300.00 to repair. Now half way through washing the dishes again no water will go into the machine. Only the first part of the cycle. I am sure it is going to be the panel box after reading other peoples problems with this machine. I will not pay to have it fixed this time. I will have to buy a new dishwasher. I will never purchase a Maytag product ever again. I have lived in my home for 40 years and never had a problem with any appliances. This would have been my third dishwasher in 40 years and as you can see it has not even lasted 4 years. I will inform my friends to stay away from Maytag.

Dryer delivered nonfunctional. Tech showed up the following Tuesday. Diagnosis main board and one sensor dead. Tech returns following Thursday. Replacement board DOA. New dryer still nonfunctional. Awaiting new board with no functional $1100 dryer. This dryer replaced my three year old Maximus which was deemed too expensive to repair after three repairs. Please do not buy a Maytag/Whirlpool product.

My name is Luis ** and I own a Laundromat in Yuma, AZ. I recently purchased 10 Maytag top loaders model MVW18PDAWW in August, so the machines are practically new. They are the new HE top loaders with locking lids. Since I purchased them I have had nothing but trouble. Customers have complained about them on a regular basis; there are days when we have had as many as five complaints.First of all, the locking lids proved to be a much bigger problem than we anticipated. People want to open top loaders to add fabric softeners and when we have opened them so that they can add the fabric softener they are often disappointed with the level of water in the washer. Those people consequently refused to use those particular washers. People have pressed the buttons on the control boards and sent the machines into a loop; different readings have appeared on the screen. Some of them say out of order, sync and several other error codes. Eventually the machines reset themselves or I have had to reset the programming. In the meantime the people pass the word and those machines are not used by those who hear. The controls are too sensitive and are not suited to a commercial coin laundry.Whenever any buttons on the control board are pressed the time of the wash appears on the board. Because of this some people who are busy and are using and loading several washers claim that they have already put their money into the machines; they argue with the attendant or with us. Many times they actually believe that they have placed money in the machine and many times they try to get a free wash from us. Either way they are unhappy and they, and those who hear them argue, will not use those washers again. In most cases we lose them as customers and once customers are lost they never return.I placed them in a location where the previous Maytags had been heavily used, expecting them to replace the old machine. I was wrong. They are used very little and the long and short of it is that we are losing money and since our busy season is coming up, will be losing even more customers and therefore more money. I spent close to $12,000 on the machines, including delivery and installation and right now they are quickly becoming heavy paper weights. I have contacted the salesman who sold them to us, but he has given us the runaround and done nothing about the situation.

I sold my 20 year old Maytag set and upgraded to this Maytag Bravos washer. This machine takes almost 1 hour to do a load and they come out dirty. Only way to get clean is to set on bulky sheet which uses twice as much water as old machine. This unit should have never been put on the market.

I purchase the Maytag Bravos washer & dryer set 3 1/2 years ago brand new. I figured being a Maytag it would last for a long time but nope I was wrong??? I will never buy another Maytag product as long as I live and I will tell all my friends and family not to purchase a Maytag product also!

Im have finally given up and purchased a replacement for my Maytag Bravos XL Top Loading High Efficiency Washer! The Maytag was 2 years old and I have ALWAYS had trouble with it. My towels became sour after 1 or 2 uses (sometimes they smell sour even before use!). My dark clothes ALWAYS came out of the wash LOADED with lint. I researched online to determine whether these were common problems and found several sites with suggestions such as: dont use more than 1-2 spoons full of high efficiency detergent (which recommendation I followed), Use white vinegar or liquid fabric softener. (I tried both with only minimal results.) ALSO use a dryer sheet in the dryer (I did this but it seemed like a waste since I was already using fabric softener in the washer). Dont overload the washer. (I didnt, but if I couldnt fill it, then why did I buy a washer with such a large tub ?!) Clean the washer monthly. (I faithfully did so, and tried alternating Affresh and bleach to see if theres any difference in the result... not really. Make sure you are fully drying the towels (I ALWAYS DID!).We had a Sears repair technician come to the house the last time my frustration level was overflowing and she only made me feel like an idiot, repeating some of the above recommendations and insisting they would solve the problem -- which, if they had worked, would have precluded my need to call a repair technician!!! The repair technician provided no other service or ideas to fix the problems. My husband decided we should go back to the tried and true agitator-type washer... bye-bye, Maytag Bravos.

Currently own model MTB1504ARW, serial number 12541413GT refrigerator. The defrost thermostat broke and it is causing the device to frost over and not cool. Maytag is trying to replace the part with part number 63001051 and that part does not match the part that came with the machine. I spoke with a supervisor, Mr. ** who certainly was not a problem solver or any help, in other words, lacks customer service. I explained the installation of the wrong part may be dangerous and could cause a potential fire or hazard. He assured me this was the part available, but also said it was discontinued and I would have to find it with an outside vendor. I explained I compared the part removed and the part they are suggestion, per the part list, and its the wrong part. As a supervisor, Mr. ** failed to provide true customer service for myself and future customers who may be in the same situation, with the potential of causing a hazard for customers. The Maytag supervisor should learn to provide customer service and prevent possible hazards for customers, taking the next necessary steps or research the issue with other departments within Maytag. The parts below are evidence of the issue, the suggested part has two wires, the one from the refrigerator has three... poor customer service, at best with potential hazards to families and children. It may because their appliances dont break, according to their commercials, they just have too much time on their hands and cant provide the assistance that is needed.

I asked a simple question online to see the location of the lint trap on my washer, I had read my manual and could find nothing about the lint trap, and to get a simple answer as to location, they wanted to be paid $30.00, I dont want them to come and show me just a simple answer as to where I could find it. It should be in the owners manual but it isnt

I have the model with a smaller oven on top. I use it about 98% of the time so Im not wasting energy having to heat a larger oven space. I also like the fact that I can clean one oven. The larger oven is used when I cook turkeys. I can cook many dishes at a time, by using the smaller oven for dressing or cakes.

Had previous Maytag for years. Good, reliable, easily repaired product. Cycle sequencing very recognizable. New washing machines are ridiculously designed. Neither you nor the repairman have any idea what the cycles are or if they are even working as designed. Many cycles start out trying to wash with little or no visible water in the drum (top loader). The clothes come out tied in knots. I now wait for the agitation to start then pause and add water for three to five minutes then restart. What a nuisance. I have called customer care many times and they are courteous but not very helpful. This machine is an engineering nightmare. If I were in charge I would retire the people who dreamt up this contraption and get back to something reasonable before all their credibility is lost FOREVER!!

I bought the washer/dryer a few years ago. I did not realize how they do not own up to their reputation. Rather expensive. My clothes are always twisted together when finished washing. Parts of them feel dry. My dryer seems to be ok. Comforters are a pain as the load always gets unbalanced. Lately it wont finish a load. I get LD all the time. Have to unplug the washer and wait for it to cut off before cutting it back on. Then I cannot just rinse or spin. It fills back up with water and I get the same LD again. If I had seen all these reviews before I bought this set I WOULD NOT have bought them in the first place.

Weve had 2 Maytag washers that lasted a combined 41 years. Five years ago we purchased a Bravos XL top load washing machine directly from Whirlpool. Like many other reviews, it is impossible to keep the machine from going out of balance and trying to tear the laundry room apart. I called Maytag and of course they want to make sure the machine is level in at least 3 dimensional space as well as 2 parallel dimensions per String Theory. As far as the 3 dimensions, I assured them I had already thought of this (as an aside, ever try to find any flat metal on one of these machines? Kind of helps when using a level.)So after more exciting conversation, they offered me a Warranty for $437. While trying to control my laughter, I said I could trash the Bravos and buy a new machine for that price. As far as repairing it, it cost $120 for a repairman to grace my door step plus $35 every 15 minutes plus parts -- again, the decision is to trash it and buy a new machine. In case I was too subtle in my comments, I WILL NEVER BUY A WHIRLPOOL PRODUCT AGAIN. Im too frustrated to tell you about my KitchenAid fridge. As much as I detest it, I am forced to join the buy and trash 5 year club . Sometimes the good old days were really better.

I just had an astonishing phone call with Maytag customer service (1-800-344-1274). My mind is boggled; my tongue is tied. Only Consumeraffairs.com can offer relief from the bleak, solitary misery engendered by this disorienting encounter. I called Maytag to seek information regarding the number of gallons used by any of the wash cycles of the Maytag BRAVOS series 300 (Model: MVWB450WQ2). I live in California, and like millions of others, Im curious as to what the maximum amount of water used per wash might be. I told the customer service agent that Id be happy with an estimate of any parameter: the maximum water demand for any cycle, the minimum, the average any ballpark estimate would be great! My goal is to change in a meaningful way our weekly water use. How much does it matter if I do my familys laundry once vs. twice per week? Is it any more water-efficient to run one large load vs. two small ones? The Customer Service agents would offer only a scripted response to my query. Could they tell me the minimum or maximum amount of water used (on average) by any of the cycles? Any cycle any condition, just an estimate, please. A universal it depends was all I could extract.The scripted answer? The amount of water used depends on the sensor and the exact conditions. Well, yes, of course; I dont expect a specific amount. Just as the amount of gas used by a car depends on the length of a trip and the speed driven, the amount of water used per cycle will vary, but nevertheless we know, more or less, how much gas is used by a Toyota Camry on a trip between New York and the Maytag Customer Service office in Benton Harbor, Michigan. I noted that, if Maytag claims to build high efficiency (HE) machines, then they must be HE in comparison to something, right? -- otherwise how could they claim that these machines used less water? Less than... what?** insisted that no one at Maytag could tell me the answer. He asked, What reason could Maytag have not to disclose this information? I know this isnt the answer you want to hear, but its simply not available. Not even a range of water use per cycle required/solicited/demanded by the sensor? Can Maytags engineers be so indifferent that they never tested any cycle for its water use, but instead they just imagine that, by virtue of its mysterious sensor, it was lower than the use by their non-efficient machines? Your help in getting to the bottom of what felt like an act of stonewalling would be highly appreciated!

Our oven is 3 years old and the last time I used the self clean option caused the control panel to malfunction. Now we have to buy a new panel. The repair guy online advises people not to use the self clean as this is a common problem!!! What? I cant use that feature? That is so ridiculous!!! Now we have to pay $300. Whatever happened to the Maytag claim to quality and you would never see a Maytag repair man? Something needs to be done about the problem of appliances and electronics being so poorly made and basically disposable.

I purchased my Maytag washer and dryer set from the Maytag store in Glendale, AZ in September 2005. I even bought the stands for them. With my purchase, I got the extended warranty for four more years. I didnt realize that I would really need it. I have had so many issues with the washer and dryer I cant even count - from the control panel not working, to the noise and the vibration when washing, or maybe in the smell of moldy cheese. I also have issues with the constant chimes of D5 code that keeps coming up on the display screen. After 2009, I finally gave up on calling the Maytag customer service folks to have someone come and service the washer because it was out of warranty. I just decided to live with all those issues.As far as my dryer goes, the rollers went bad and that was replaced. The burnt smell isnt so bad as long as you use a wire hanger with a sock on the end of it and clean the inside of the vent. Then try to vacuum it, take the sock, get it wet, and clean the inside of the vent again. This was the most expensive piece of junk I have ever purchased in my life (almost $3,000.00 with the stands and warranty).What really gets me upset is I had the Maytag people servicing my washer and dryer up until 2009 and no one told me about a recall of my washer and dryer. The only reason I found out about it was searching for the specs as the washer finally died and I am replacing it. Trust me. I will not be purchasing a Maytag. I know that Whirlpool purchased Maytag so I am not even going to consider Whirlpool either. Since Whirlpool purchased Maytag, Whirlpool should have contacted all Maytag consumers, (which they didnt), put ads in newspapers (which I did not see) or put an ad on TV. None of these appeared to have happened.By the way, when I bought my Maytag appliances, I was supposed to get a $200 rebate for buying the stands that never came. It must have gotten lost in the mail - as well as the Tide coupons for three years. You, guys, remember that too. I will never ever purchase a Maytag appliance or Whirlpool, since they own Maytag now.

We purchased a Maytag MFI2670XEW6 french door/Bottom freezer refrigerator in July of 2012 through Home Depot and for the past 6 months have had to scrape ice off the bottom of freezer every 5 days or so to prevent water flowing on floor. I see so many exact complaints from people that I am just fuming! Cannot believe this company is not backing their products up with that issue. A recall should most definitely been done. I grew up believing Maytag was top of the line but I am wrong. I bought this to replace a 16 year old GE refrigerator (side by side) which I never had any problem with and now I regret not replacing it with another GE. I havent contacted the company yet as I thought I would check complaint reviews before I did that but it seems that the company is just treating their customers like dirt. To spend $2200 for a refrigerator and have problems within the first 3 years is unacceptable!!! They had better start going good on this problem or face the fact that they will no longer be in business a short time down the road. The best form of advertising is word of mouth and online reviews and it looks like they are going to lose a lot of customers with the direction they are taking.

Purchased a Maytag MSD2553WEW00 refrigerator on 2/27/2011 from Home Depot. Began using it in July 2012 upon completion of home construction. In February 2014, after less than two years of service, the refrigerator was running but no longer cooling. After the expense of several part replacements and a service call, it was determined that the compressor had failed. Unlike most manufacturers, Maytag did not warrant the compressor and closed system beyond 12 months. The refrigerator looks like new but the cost of repair is prohibitive relative to purchasing another new refrigerator. Maytag was contacted but was not helpful.

Bought a French door Maytag with freezer on the bottom. Ice build up on the bottom of the freezer and it has ruined my floor. We are replacing the floor in the kitchen. It is only a few years old. They have horrible customer service and will not replace anything.

I bought a brand new refrigerator and about four months into using it, the freezer door began to become loose and opened by itself automatically. It also started to leak so I called the company continuously looking for a solution. However, they never resolved my problem. The company sent a technician. However he was unable to fix the problem. The technician said it was fine and did absolutely nothing. And now I am still waiting, but now your company says my warranty is up EVEN THOUGH I called much earlier and your company did NOTHING to help me. I need someone who can handle my problem. Ive been using your products for many years, and have always been satisfied by it. But this refrigerator has changed my perspective. I hope you give this a peace of mind and treat your other customers better.

Purchased 2/13. Used maybe 3 times per week. Panel has gone haywire 6/14. 3 months out of warranty. Confirmed, bad control panel. We need class action lawsuit. This is ridiculous! Same issue with hundreds, likely many more unreported of dishwashers from Frigidaire/Maytag. I found number to law firm preparing suit... **.

I have had Maytags for 20 years and never have been disappointed before I bought the Centennial and it is junk. It doesnt even put enough water in to wash the clothes. After it breaks, I will never buy Maytag again. When did you guys start going down the drain literally? My clothes do not get cleaned. I live in the country and we all get dirty. We need a dependable washer and dont even get me started on the dryer. I thought maybe you would care enough to know.

Our washing machine is 3 years old. About a year ago we started to see hairline cracks on the plastic lid in the bottom corners by the hinges. These have now become huge and pieces of plastic are breaking off every time we do a load of laundry. Maytag (under the Whirlpool brand) will not replace the lid for us. We paid $130 for a tech to come out and confirm what we already knew - that we need a new lid. And now the parts and labor will cost over $550. We have called customer service several times and spoken to a supervisor and the best they can offer us is to pay for the part which still leaves us to pay over $400 out of pocket to repair a $600 washing machine. This seems to be a common problem and is all over Google, yet Maytag is not willing to help their customers.

My Maytag refrigerator was purchased from Home Depot less than 3 years ago. It is a French door, bottom freezer draw model #MFI2569VEA1. Every four days, there is a huge puddle of water at the base of the unit and it is starting to ruin my ceramic tiles. I tried the online video solutions to no avail. Home Depot wont repair it, they told me to contact Maytag. Maytag wants me to purchase a $375 warranty, which is 30% of what I paid for the refrigerator. I will never buy a Maytag refrigerator again, or any Maytag product for that matter. They once stood for solid reliability and peace of mind, now you get a piece of junk instead. I cant even sell it on Craigslist if I wanted to because who would want it? If a class action suit is ever initiated, Ill be on board. I hope Consumer Affairs contacts me.

We purchased our Maytag Bravos washer/dryer in January of 2012. In October of 2013, I noticed that the lid would not close properly. In examining the lid, we discovered that the screws were in tact but the information panel on the inside of the lid had come unglued causing the lid to be obstructed from closing properly. After calling Maytag we were told that they make a quality product and, in what I consider to be a condescending reply, could not help us. Replacement of the lid with the service call would cost almost the cost of this expensive washer. So disappointed in what we thought was a wise purchase!

It went bad, then I called a technician who replaced the compressor. After a few months, it broke down again after I had bought new parts for it. I was very dissatisfied with how the refrigerator was built. I spent lots of money on it, and it wasnt worth it.

My Maytag washer and dryer (5000 Series) is about 2 years old. Just as soon as the warranty ran out, I started getting F35 and suds error messages. Information found on the internet tells me that many Maytag customers have experienced the same problem. Whats up with this Maytag? Since many of your customers have experienced the same problems, are you willing to meet the consumer in the middle by repairing the product at no cost or are you building the appliances to last as long as the warranty?

Dishwasher model: MDBH949AWW3. Gradually over a months time lost its control functions and its status display. Ten days ago the last button to fail was the start button and the dishwasher stopped working. Maytag confirmed over the phone that there was no recall on this model. The part costs $190 and is out of stock till end of October 2013. I opened the dishwasher and took a closer look at the keypad. It has the cheapest touch buttons I ever seen. Maytag had provided at purchase time a user guide and a large sheet with a sketchy incomplete drawing (W10142800C) for service use only. I made my own schematics and I built my own keypad for less than $50. You may notice that the info I have on my attached schematics is missing from Maytag/Whirlpool incomplete drawing. My keypad is working fine and will outlast all the remaining parts in that dishwasher. I wish there is an angry lawyer out there with a bad dishwasher like mine that will use this info to sue Maytag. Please give the schematics to any user having troubles with this lousy touch pad.

After having a Maytag washer/dryer set that lasted 20 years, I decided to go with Maytag again. Big mistake! Centennial Dryer has already broke down and the parts, before the overcharged shipping, was over $100. I wish I had done some research. Maytag is no longer Maytag, it was purchased by Whirlpool. Hence the lack of quality. Not only that, I dislike doing business with heartless companies that just close shop & let loyal employees go while paying upper management fat severance pay. Then Whirlpool changed the vested lifetime benefits of the Maytag retirees. Will not buy another Maytag appliance and will never purchase a Whirlpool product.

I wish I had found this website before I bought my new Maytag washer and dryer from Home Depot on March 7, 2018. I replaced a 30 year old Maytag washer that I should have kept. I wash two loads a week so has not been used that much and now it will not drain. I tried everything, canceled the cycle out, checked the circuit breaker, unplugged it, removed the clothing, bucketed out the excess water, tried the drain and spin cycle, etc. Just will not drain or spin. Repairman is coming next week... Still under first year warranty but if it is not the “fault” of Maytag I was told there will be a $90+ minimum service charge.

My Maytag Bravo washing machine is very basic and convenient. It was the first appliance I bought when I purchased my new home in September of 2019. it is commercial grade so I’m able to wash everything from towels to comforters to heavy coats. I like the clean lines of it and the knobs are easy to use and are perfect for my needs. It has wrinkle control, deep water wash, a variety of temperatures including tap, cold, cool, warm and hot. There is a fabric softener feature and an extra rinse. The push button Start is perfect and easy to use.

Run away from this piece of junk machine AND company as fast as you can! I bought this set Oct 12 and by March 14 it was grinding/whining during the agitation cycle. I have been in contact through various forms with Maytag and they do not care! They first contacted me to review them and when I reviewed them very unfavorably they emailed me and this is what they said: Our staff has read your review and values your contribution even though it did not meet all our website guidelines. Thanks for sharing, and we hope to publish next time! All I did was say exactly what happened.After that I went to their website to see what kind of reviews they were getting and lo and behold their rating is 4.4 out of 5. Of course it is when you simply cherry pick the best and plant a few lesser rated ones. I simply do not have the funds to replace what I thought was a quality product, nor am I sure I want to repair it as it doesnt clean clothes. I hate having been placed in this predicament by a greedy, slimy corporation whose only interest in me is profits.

I own my oven for 10 years. It still looks brand new. The bottom oven went out and they do not sell the replacement parts anymore. I think its terrible that I had to go and buy a new oven when mine still looks brand new.

First we bought the washer and not even a month after it was ruined. In the span of the year that weve had it, it has broken down about three times. Then we bought the matching dryer in August and by the beginning of December it has broken down. Called customer service and they are not coming until January 18. Have me waiting over a month to fix it. Worst brand ever and even worse customer service. Never again will I buy anything from this brand.

Maytag refrigerator model MFF2558VEM9 purchased in November 2012 from Home Depot for $1329 suddenly would not maintain freezer temperature under high 20s in April 2017 (4 years, 5 months). Repairman says it has coolant leak, probably due to corrosion within the sealed system. Cost to repair - $1500. Repairman says this is a common problem.

Maytag Bravos XL he Washing Machine - Having owned several Maytag washers in the past, I thought this would be perfect, instead, it is the worst washing machine I have ever had. This machine does not clean well at all, spots on clothes stay put. I have tried different amounts of HE detergent and clothes are twisted and wrinkled terribly and have remaining soap residue on them, even when I use less soap than recommended. I wish I would have returned this machine immediately after a few loads. It doesnt get better with time. It is very loud, but that is the least of its problems.

Approx. 3 year old Maytag Dishwasher Control Panel lights blinking with Dishwasher inoperable. Repair part (new Control Panel) costs approx. $180 plus tax. When you add the cost of a service repairman you are nearly at the price of a new dishwasher. I am completely unhappy with this Maytag Product and will never buy another Maytag Product again.

Just like so many others, our Maytag 300 Quiet Series, just 2 years old, has a malfunctioning control panel. Repairman told us this has been an ongoing problem with Maytag dishwashers. Steam/water gets into the control panel.For a while it worked on and off and now it is dead. I am saving up to do the repair, but in the meantime the dishwasher sits idle.

I purchased a Maytag commercial residential washer in late 2018, supposed to have a warranty for at least 5 years. We are in California and I was told that there was only one facility that could come two weeks later. I removed the front panel to have it ready for service tech, who on the first visit kept saying he did not know what the problem was, and left telling me he would order parts. After Christmas, I could not get in touch with service so again called Maytag. Service was supposed to come out on the 30th.After waiting almost 3 hours, he called to tell me he did not have the parts. Also, this repair tech treated me very bad since I removed the front panel which I thought I was being nice. He called me back on the 30th, said someone gave him a part, and came. All he did was remove control panel, lost the start button and told me it worked without checking it at all. He was rushing to another appointment so I tried to start it and it still had the original issue, which was slow agitator and a rubbing/grinding sound. Now, after he did something with control panel it had a clicking sound. I immediately called corporate and was told when he came back, which has now been over a month with no washer, that he would be with a senior technician.January 5th I waited all afternoon and he called and said he was not coming and that my whole washer would have to be rebuilt. He never replaced the parts on previous invoices I received, and I filed a complaint with the BBB. Now they are completely lying. Technician trying to say I had the control panel apart which is not true, and does not match up with the invoices I received. They are telling me my warranty is voided! Its been a month and a half. I was treated rudely from the beginning and now I am obviously being retaliated against. I have 3 kids, two with severe medical problems and have put so many hours into calling with all these issues.I had another service place come out and he removed the agitator and the transmission shaft/drive motor is rusted out, as well as the parts he said he replaced are worn and definitely not new. For this company to come back after all this time and say I did this, when I have the original invoice that clearly states otherwise is absolutely the worst service ever.I bought this machine thinking it would last, and now have to deal with all this. I have nerve damage and it is very difficult to take all the laundry for a family of 5 to do at laundromat. They refused to send someone else out, where they could easily have seen this repair tech never did what he said, and was unable to diagnose and fix the issue. Its appalling to me that this is how they treat customers. Laura ** at corporate is the one saying warranty is voided. The machine looks brand new as it has always been taken care of. They should be ashamed of themselves. Apparently, this is the standard a lot of times with people trying to get things serviced under a Manufacturer warranty!

Maytag Bravos XL HE MVWB725BW. Washer was fantastic at first. Then about at 14 months old, the spin cycle starting making loud noises. Called Maytag, they promptly dispatched a repair service. The estimate to fix the washer was $531. The repair man stated Maytag does NOT seal the bearings from the factory. They only rely on a rubber washer, poor design. Maytag was unwilling to help with a washer with their name on it that failed at 14 months in any shape or fashion. She mentioned that Maytag has a 2-10 warranty on the motor only (which is non-existent, its electromagnetic). This will be the last Maytag that I ever intend to purchase.

It is not worth the money. I paid $2500.00 for a Maytag refrigerator that I had for two months. Two service calls were made to Maytag as of 07/07/2014, the problem no ice and the refrigerator stays warm. The problem has not been resolve and Maytag refuses to replace the item.

First of all how you wash a load of laundry with a cup full of water? I got this washer and dryer (XL Bravos) as a birthday gift from my husband. This is the worst washer Ive ever had. It takes forever to wash and the laundry is still dirty, it only has a cupful of water in it. Im so disappointed at Maytag for selling something like this. If anyone is doing a class act lawsuit please include me in.

Maytag Bravos electric steam dryer purchased 2009 - I have had to replace the door hinges within one year of usage at my expense. The blower belt and pulley had come off twice, the last time about a half hour after the repairman (again at my expense) left. I put it back on myself and if it comes off again, I will use Locktite to glue it on the blower shaft. I figure I will be lucky if this crap lasts a couple more years anyway. No more Maytag for us! What does it take for the consumer to get some representation with regard to lemon laws here? I will take my wrath out on Home Depot here since I have no recourse. If enough people complain, maybe they will stop selling that junk. I also will disregard Consumer Reports in the future.

I bought my Maytag dishwasher on September 4, 2013. In August 2014 the control panel went out. (Sound familiar?) The dishwasher was still under warranty, so I called Maytag. It took 3 tries to find a repair person who would come out on my schedule. (Im a teacher and cant take time off.) They installed the new control panel, and it working. I tried to submit a review on Maytags website, but my review was denied. I guess they didnt want to hear the truth.

Maytag dishwasher mdb7749awm2 - It appears that everybody who bought one of these dishwashers has run into this issue at one time or another, and it usually takes one full year of use before the control panel goes out on these units, and in most cases, it has to do with moisture getting on the thin strip of wires leading from the control board to the control panel. It usually occurs right where the strip enters the control panel... There is nice little gap for moisture to rest right on the wires, which will eventually lead to corrosion. I included an image of what to look for (see the nice black rust areas on the wires? That was my problem, and probably yours, too). If you have some very, very fine sandpaper, and have patience, then you can get the rust off the wire, but be very, very careful, or you could take the small thin wire off in the process! Ive made this repair myself to my unit, and I did it for one my friends machines (it was a Maytag, and his lasted two years, but had the same problem, too), and both had similar problems and right in the same spot! After removing the corrosion, the system worked great again. However, before hooking the unit up again, I sealed the area with some silicone to hopefully prevent this from happening again. Now, Im not saying that this is the problem that you are having, but its worth investigating, and dont be afraid to pull-off the front panel...its just held on with an adhesive and will go back on with no issues. Anyway, this could save one hundreds of dollars in repair costs. I hope that this helps.

After the waranty ran out, oven failed to ignite. Called repairman who couldnt diagnose problem. Broiler works. Replaced some kind of wire & part for $350. Good for 6 months. Happening again. Paid a lot for this oven.

Bought Maytag Bravos from Home Depot in Dec 2010. Wife didnt like the way it cleaned clothes right from the start. It wouldnt get clothes as clean as her 20+ year old washer. 2 1/2 years later and her $900 washing machine needs $600 in repairs. My wife will finally be happy with the way her washing machine cleans again because we are purchasing a new one this week, and it wont be a Maytag.

I purchased a Maytag Top Loader Washer MVWX500XL last May 2011 from Home Depot to replaced our 15-year old GE washing machine. Two weeks ago, it started making horrible noise like a jet engine taking off during spin cycle. I called in the Maytag repairman and was told that the bearing is gone and it will cost $ 493.00 to repair it. He claims that the damage is caused by not using HE detergent exclusively and he refused to leave us a written estimate. We are only three adults in our household and we do our laundry once or twice a week. For this machine to be repaired only after 2 1/2 years of light service and for almost the same cost as a new one, I will never buy another Maytag/Whirlpool products ever again and I will encourage everyone the same.

Im furious beyond belief with Maytag. Im furious at myself for being stupid enough to purchase all new Maytag appliances when I purchased this home as I had horrible experiences with them in my former home. This concerns the Maytag over the range microwave oven model MMV4205AA. First of all, within 6 or 7 months after purchasing it while cooking a frozen dinner, the turntable just cracked in half. Maytag wanted $89 to replace it. I knew when the turntable cracked that there were more issues to come. That is not normal in any way for that to occur in a microwave.Problems continued, of course, and with each call to Maytag, they would say the same thing the microwave is out of warranty and refused to assist me. Its not some little table top thing that one can just toss out and buy a new one. I paid about $400 for it from Home Depot. Last week, without it even being turned on, it just stopped working. I checked the electrical supply and conduit to make sure that was okay. I called numerous service organizations who told me this sudden breakdown when the microwave isnt even turned on is a known issue with this model and several other Maytag over the range models. Ive called them (Maytag) three times in the last week and they refuse to provide any allowance and hear the same old thing, the microwave is out of warranty. I was willing to have them even just provide some assistance rather than replace the microwave. Ive been told by numerous service organizations that this is a known issue and that even if they repair it, it will occur again and again and Im best off purchasing a different brand, which I cannot afford. They gave me phone numbers for service organizations authorized to service Maytag products and this just goes to show how out of touch they are. They gave me one that isnt even in business anymore. How professional, not!Warning: Purchase Maytag at your own risk. I give you fair warning. Every single Maytag product Ive ever owned has been a problem. I will never, ever, ever purchase another Maytag product again. I would think just out of decent customer relations, that theyd repair this issue. To be honest, I dont really trust a repair as Ive been told it will happen again and again. There was no notice that the microwave was breaking down either. It wasnt turned on. One day, I went to use it and it just wouldnt work. Actually, I went to use the timer on it and thats how I found out it was dust. My advice is stay away from Maytag. If you read reports, there are more complaints on Maytag than any other appliance manufacturer in existence. Not only on their products, but their customer service too.

My boyfriend and I just recently purchased a Maytag brand washer and dryer set. So far, we are thrilled with our purchase. We got front load units that have an XL barrel so we can use it to wash comforters and larger loads. I have washed many loads and so far, havent noticed a longer time to wash or any issues. I love the fact that my clothes are all getting equally as clean and I can be sure that my items will not be torn or ripped in the process. I would recommend this product to anyone.

My Maytag is 2 weeks old, and knew from the start I had a lemon. The compressor sounds like a giant freezer. I had the service man take a look at it, and while he was here the compressor did not come on. He pulled the plug from the fridge and turned it back on and still it did not turn on. I asked him to stay till it turned on and he said he could not stay any longer. I waited for him from 2 PM till 7:30 PM. He was to arrive between 3 and 6. Talk about frustration, and I only wish I had read all the reports before I bought this junker. I was so worried I decided to get the insurance for 4 years. The reason the ice forms is because you have no control over the ice. You cant see them and they get stuck. I had a side by side before this, and I can kick myself for not buying a side by side again. I was told to shut it it down when youve had enough ice cubes, to stop it from getting stuck. This ice maker is so big and so hard to pull out and the switch to turn it off is on the inside. So far my only complaint was the humming, but I can see a tough road ahead.

I purchased my Bravos (ecoconserve) washing machine in 8/2013 from hhgreg. The problem I have is this grinding noise with the spin cycle. So I unplug the machine because the lock lid light is flashing and wont unlock unless I unplug the machine. I grew up on Maytag so that was the reason I purchased this machine but never again. I am so disappointed in this product. :(

I bought my Maytag dishwasher MDB7749SBM0 three years ago. After it was in one month it already needed a service call. It needed a control panel. Out of the dishwasher 4 weeks because this happened over Thanksgiving. Two months later it stopped working and needed another service call. Technician was inexperienced and another one had to be called. Out of the dishwasher 3 weeks. At this time, and because of the expense of the machine, I purchased an extended warranty. This was control panel number two. Not long after, the heating element had to be replaced. Two weeks without the dishwasher. Now, my dishwasher stopped working again and it needs a new control panel. The technician is rude but did offer the information that the moisture ruins the control panels. IT IS A DISHWASHER!!! IT USES WATER!!! I only run the dishwasher twice per week so I cant imagine how poorly it would hold up if it was run more often. I am on my third week without the dishwasher because the part is on back-order! No one can tell us when it will be in. I bought a Maytag because I thought they had the appliance market under control. MY MISTAKE! I am very angry.