I purchased a Maytag dishwasher in March 2005. About every 8 to 12 months since Ive owned it, the control panel malfunctions and needs to be replaced. I was told by the repairmen (similar to the many other postings below) that the malfunction is due to a faulty design where warm moisture shorts out the electronic control panel. For a few years, I paid for a service contract. But this seemed quite unfair, given the regularity of the same malfunction. Given that this is such a common problem, isnt there some responsibility by Maytag? This is clearly a faulty design. What about the legal responsibility for a recall? Is it possible that, together with other aggrieved owners, a lawsuit against Maytag would be the appropriate action?

We bought the Bravo washer and dryer in 10/2009. Since then the dryer has never worked well. Weve had at least 8 service calls on same and the sensor doesnt work, i.e. says the clothes are dry when they arent and we always have to run them through at least two-timed cycles to make them completely dry. The washer is another nightmare. At least 8 service calls as well, and after one where the motor was replaced, it popped off and flooded my entire house. They laundry room is located on the second floor. I had to replace floors, walls, ceiling, light fixtures, etc. Insurance covered it but it never shouldve happened. Now the washer doesnt drain properly and the error code LD displays every load and we must manually drain it by either setting an extra drain cycle or take the entire machine apart and vacuum out the water. Each load takes twice the amount of time it should, if not more. But I guess its okay because the dryer takes just as long to dry a load of clothes. Something has to be done. Maytag is refusing to stand behind their products and it seems as though many of the complaints are for the same issues. Is there a lemon law for household appliances?

I purchased Maytag Centennial Commercial washer and dryer eleven years ago. Both are still going strong. It has been a great purchase. Only issue is a couple of stains have appeared on outside of appliances.

I have a Maytag fridge (model # 2258VEM4) which I have had for 4 years. A few months ago, it started leaking water on the floor and notice that it had a bed of ice on the floor of the freezer. Reading the list of complaints in this site for the same issue, it sounds like it is a design problem.

I bought an off-white or light cream color gas Maytag stove about three years ago. When I first used it to boil some water for tea, the light colored grills turned black. And this is without cooking a full meal, merely boiling water. After a few more uses with light cooking, and a few spills on the cooktop, I discovered that it was simply impossible to clean. The glass on the oven door became discolored with the first use, and is also impossible to clean. I purchased several types of cleaning items and sponges, and nothing works. This is a disgusting stove. I hate it and I wish I never bought it. I will never purchase a Maytag anything ever again. Its the poorest and cheapest no-quality item - a total waste of money.

I purchased the Maytag MDB7749SBM dishwasher just over 2 years ago. After owning for 1.5 years, the control board malfunctioned. After discussions with Maytag customer service that began in late December 2014, it was finally repaired in February 2015, with the control board being completely replaced. Within just a few months the dishwasher again fails. The first time, it would not stop running. This time, it will not run at all. I called customer service today (August 1, 2015) and they expect me to pay for the repair.It is easy to Google and find multiple review sites that indicate hundreds of consumers have similar problems, but Maytag will not acknowledge any issue, as the customer service rep indicated today (she said her information showed no recalls). Within two years I am now faced with paying $600+ for a dishwasher for a second time. This is terrible customer service on Maytags part. They have lost my business and I am warning consumers on every platform I have.

The machine dries out the clothes so tight that they are full of wrinkles. I am so dissatisfied with this machine, I spent almost $600.00 for this and this is what I get. I also end up with fabric softener all over the clothes. I use the Downy Ball and I just took out my black pants to find blue all over them. I contacted Home Depot where I purchased the machine. They said to get a hold of you. All I want is get a different machine, not an HE. This is beyond anything. Someone should have to put up with, can you help me?

I purchased a Maytag Dishwasher Model MDB7749SBM3 in January of 2014. I have had issues with the control board for the past month: lights come up at random; it takes 3 to 10 trials to get it to start and now it is dead. After reading many reviews on this site, I now understand what the problem is. I called Maytag customer service and they wanted to schedule a service call at $98 just for the diagnostic. I asked the Maytag associate whether the control panel issue was a common problem and she said she would research that but did not give me an answer. I am totally disgusted by this company!!! I would be happy to join a class action suit.

We purchased a high-end stainless steel interior/exterior unit in January 15. It is now July 15 and we have not been able to get any use out of it. Day 1 washer leaked. Full day off for service. Guy told us we were using the wrong soap. It leaked on the very next wash. Called again. They forgot to check the soap dispenser. Another service/day off. Leaked again! Another service call/day off. They replace the dispenser & seal. Now washer no longer leaks but the dishes are dirty and wet even days later. Another service call. Another new part. And now we are waiting for our 5th service call. We paid for a new unit and have a refurbished cobbled together piece of junk. Maytag stubbornly refuse to replace this unit.

I bought model MDBM601AWB3 in October of 2009. The control panel and wiring harness burned in August of 2011 after, at the most, running twice a week. I called customer service and talked to numerous people. All said, Too bad, out of warranty. I did a quick Google and learned it is a common problem and even a fire hazard with Maytag dishwashers. My wife, who was being treated for lung cancer at the time and was very emotional, got a hold of someone in corporate and literally cried that we could not afford the $600 to fix a problem they knew it had when they sold it to us. They relented and agreed to pay for parts; we pay labor. Today, 1/10/13, the control panel is dead again. I suspect it is the same problem as all they did was replace the panel and wires. This machine has obvious dangerous design flaws that they were aware of. I find it sad that a company can screw people like this and get away with it. What recourse do we have now?

We purchased a Maytag refrigerator Model # M1TXEMMWS02 and Serial # E01103420 in April of 2010 from Home Depot in Aurora, Illinois. First off, we did register the fridge online via Maytag which of course, they have no record of! Now, we go on vacation and come back to all of our food ruined because the refrigerator stopped working! No refrigerator should stop working within two years! I called Maytag and they offered me a Repair Plus One package of $302.73! Are you kidding? We paid $400.00 for fridge. Then of course, only one-year warranty and have to pay at least $75 for a service call, labor plus parts! If it’s the compressor, the charge is $326.20, plus shipping and handling! What a joke! There needs to be longer warranty and should offer free service calls and much more. I am disgusted in Maytag products and in which we purchased due to a reputable name! Never again.

I have never liked the stove because it is too small (it came with the triplex) and it has porcelain like top. One burner burns to hot, the other three mediocre, there isnt enough space between the burners and the back of the stove. It doesnt cook evenly and it really does not have a low or simmering setting. You cant set a timer for simmering because it cooks too fast. The knobs are stuck and sometimes wont light when you turn them down. The oven is okay, but could be better. Wish it had self cleaning. The broiler in no existence. Food way too close to the flames. We have had this oven since we bought the triplex back in 2011.

So I read the reviews when I bought this Maytag Bravo Washer and figured stuff happens. We bought the top load Maytag Brava in 2013. We bought the Home Depot warranty, 2 years later the washer was leaking water. 5 repair visits and 3 attempts to fix the leak before it was repaired. As of 4-25-17 the wash machine displayed un-level errors and started vibrating with a thundering noise. Called out warranty repair and they stated we need new bearings. Repair is scheduled in 2 days and now the wash machine is thundering and spewing oil so it is shut off. 4 years old, and like the other complaints clothes come out with dry patches and not clean. This is a bad machine, we are saving for our next washer. It will have an old style spindle/agitator, no California efficiency and probably not Maytag.

We just purchased a house with new appliances. They are Maytag. When I use my stove the oven heats. I have no idea why. I wondered if anyone else has had this problem. When I turn it off it turned off but it turns back on when the oven is on.

Just purchased a maytag dishwasher from home depot. I did the install myself. The dishwasher will not work at all the panel lights up, but no water goes into the washer. I now must wait two days for repair. After reading all the other reviews, I am thinking about returning it for another brand. And yes the water supply is on. I have hooked up several dishwashers. This is the first time a brand new one did not work right from the store.

We purchased all new Maytag appliances when we built our house. So far, the stove/oven has quit working and been repaired 3 times; its always the ignitor. The dishwasher has been fixed twice. The washer no longer spins out as it should. The refrigerator and dryer so far have run okay. I am definitely going to change brands with my new appliances. I will not purchase Maytag again. Its not what it used to be. I will do without oven this time, until I can buy a new one. Also, the dishwasher door has had problems from day 1, and now, it will not close at all. It seems like its off the hinge. Definitely, its not the Maytag of years ago.

I have had the set of Maytag Bravos for about 5 years now. In the 3rd year, the bearings went out. Just recently, leaking water pump. This washer easily eats clothing. I have to disassemble every so often just to get the missing socks etc. out. The only good thing, Maytag should be ashamed I know this, is that the machine is easy to fix. I imagine since they made it so cheaply. Really nothing to the machine.

First I do like the fact that it spins at such a high speed that the water is mostly gone, and that is the good news. I do like that it uses less water but when washing any dark colored clothes there are dirt or scum like marks where the clothes may have been folded or twisted in knots which I also do not like. I have cleaned machine but this started when new. Drying doesnt get rid of those scum marks either. I never had this problem with my old full fill machine. I have used more detergent and less HE of course in both liquid and powder. Any suggestions?

I have a Maytag purchased about a year ago. My old Maytag lasted 16 years. The salesman told us that they are now built to last 8 years. It’s pretty noisy, so much so that I have to close the door to the utility room. I guess it gets the clothes clean but it used very little water. Fortunately my model has an agitator but nothing like the old kind. After looking at many models, I feel this was the best choice for the value. It is top loading which I like.

I bought my washer in 2016 and now it’s broke again. This is the fourth time! I’ve gone everything to take care of this and it’s a lemon! I will never buy Maytag again. I want to buy USA products but four times for repairs in three years is way too many. I guess it doesn’t matter what name is on it. My last washer was a GE and was still running after 15 yrs when I bought this one. Not one repair ever made on it! I’m telling everyone to stay away from maytag.

I purchased the top load Maytag Commercial Residential washer with an agitator last month. I wanted a basic washer with Hot/Warm/Cold settings, Delicate/Normal/Heavy Duty cycles, Small/Medium/Large loads. I paid over $800 for this washer and I cannot wash my whites or rags in hot water! The hot water setting dispenses hot water, then cold water, back and forth. The end result is cool water. Ive called Maytag, Ive been told that there is nothing that can be done about it, thats how theyre made to be considered HE. I asked them why they even put a hot or warm water setting on the washer.You have no control over the water level, all cycles except for normal run in a deep water setting (full drum of water), I dont know why delicates are in a deep water setting. I only wash a couple pieces of delicates together. I end up using a lot more water and detergent with this washer. I hope we dont have to conserve water in the next few years! So though this washer uses less hot water energy, it wastes a lot of water, my water bill goes up and my detergent is used up much quicker! I cannot add time to my wash cycle, (the actual washing/agitation cycle is very short - 10 minutes) it has to drain all of the water and re-start the cycle with more water! $800 is a lot of money for a washer that doesnt wash like my old cheap washer. The local store cant do anything about it and Maytag brushed me off.

Maytag Dishwasher Model MDB6759AWS3 Does Not Start - If you are having the following problem, here is what I did to fix it. All of the lights on the touch pad would light-up when pressed but the dishwasher would not start. It appears to be a corrosion problem on the connector from the touch pad to the control panel. 1. Turn off power to the dishwasher. 2. Remove the inside cover to the dishwasher door - approximately 10 screws. 3. Disconnect the electrical connections from the inside cover to the control panel still attached to the door. These are snap connectors. Always a good idea to label the connections before disconnecting in order to make sure everything goes back together properly. 4. Remove the black cover on the control panel. There are 3 screws. 5. Find the green conductor tape that connects the touch pad to the control panel. 6. You will remove the green conductor tape from the control panel. DONT just pull on it. There is a white piece of plastic that slides away from the control panel and toward the green conductor tape. It will remove pressure from the conductor tape and the conductor tape can then be disconnected from the control panel. 7. Get a good pencil eraser and clean off the exposed copper connectors in the conductor tape. 8. Place the conductor tape back into the control panel and slide the white plastic piece over it to reconnect the conductor tape to the control panel. 9. Replace cover on the control panel. 10. Reconnect the electrical connections from the inside cover to the control panel. 11. Place inside cover of the dishwasher over the proper screw holes - make sure the bottom of the inside cover is overlapping the bottom of the door - or the door wont shut properly. 12. Replace screws.13. Turn on power and check.It worked for me and saved me time waiting for a repairman and expense of the repair.

Purchased an over the cooktop microwave 3 years ago, it came with a 20 year warranty. It stopped working and I promptly emailed Maytag customer service. It took them over 3 weeks before they responded. That is not acceptable. Did they think I had a back-up microwave to take its place until they finally got around to reply to me? Well we could not wait, and we just threw that piece of junk out and had it replaced with a competitors unit. We will never buy Maytag again and will inform anyone we know about the poor operation of Maytag products and lousy customer service. My suggestion to anyone considering Maytag products is to not waste your time and money and look to another manufacturer.

We purchased this machine (Bravos XL top load washer) in August and its been nothing short of a disaster. It doesnt clean anything. Within two washes my cloth diapers were unusable, loaded with ammonia and stains. Our camping clothes wreaked of smoke. I tried multiple cycles, more detergent, less detergent, larger loads, smaller loads. Doesnt matter. It doesnt clean. I called customer service within a week and waited 6 weeks for a service call. Into third trimester of pregnancy and recovering from an MVA, I was washing soiled clothing by hand in bathtub desperate for help. I only wish Id known about their 30 day money back guarantee. After many calls, no shows and cancelled appointments, the first tech comes. He tells me the machine is fine. They just dont clean well. Hes not surprised. I call the appliance shop, they said the same thing. That they wouldnt have sold me the machine if they knew I had dirty laundry to wash. (Who washes clean laundry?). They wont help us. We call Maytag back. They send another tech. He says the same thing. Tells us to keep complaining to Maytag. I call again and they tell me that if I want a service tech, I have to pay. Theyve deleted all my feedback from their social media site and refuse to provide any assistance. The machine is nice looking and makes big promises but thats where it ends. Save your money. Youll get better results with your grandmas washboard.

Washer knots clothes into unmanageable tangle. Poor rinse leaves soap scum unless rinse extra, thus not conserving water as appliance is supposed to do. Load easily becomes unbalanced and unable to restart machine if paused to rebalance load. Will never buy another Maytag washer or dryer.

This washer is awful. We had repair guy out within year one 3 times. Changed the door gasket because it was a known problem. That did not fix problems. We have to drain and clean out hard to reach filter monthly, socks get caught in drain filter constantly. Horrible, horrible, horrible. Hate it.

I am having the same problem with the sheet of ice forming on the bottom of the freezer and leaking water out every week or so. It is getting very frustrating. After reading all these reviews I am realizing it is a manufacturing flaw and think there should be a recall. We have model MF12269VEQ3.

We purchased this Maytag washer. My wife liked it at first, but after a few months she kept complaining the wash stinks, and I can also say that. I complained to my wife about the smell of our wash, especially the wash towels. The wash was turning colors and some we threw away. My wife has been complaining about all this for months and years and said she will never buy another washer like this. Then about two years ago, she was having trouble with codes coming up. We called service, but didnt get any help, so I looked on internet and found the problem with the code. I took the washer apart and cleaned the tube out and the washer worked, but every now and then my wife needs to climb over washer and unplug, let sit, then replug back in and start it to get rid of code. My wife and I are very upset with this washer!

After less than two years the commercial washer we purchased from Lowe’s died. A repairman came out after a week and said it potentially needs a new control unit or computer. The control unit is on back order and we’ve been without a washer for a total of three weeks. The situation still remains unresolved and I’m regretting not going back to Samsung. After 9 years with a Samsung washer, it died and Samsung refunded the full price of the washer. It was a poor choice to choose American. :(

I purchased this Range about a month ago and would return it to the store if it wasnt such a hassle. The set of grates that came with had 1/4 drop from the center to front of stove. Whirlpool sent a new set; they were no better. Then customer service wanted to send a Tech out to see if the grates were out of spec. If they are out of spec they will replace. If not I will be charged $89 for a service call. Whirlpool customer service assured me their service rep would have new grates on his truck. So I drove to their service provider, he laughed and said imagine they want me to send a service Tech out to look at cooking grates and NO they don’t stock them. If you want a cooking surface that is level and does not SCRATCH BOTTOMS all your cookware. The convection oven is also a joke. In order to bake something in the specified recipe time, I have to set bake temp 25 degrees higher to compensate for convection ovens automatic temp set back feature. When I turn on LF burner flames engulf 10” pan, a truly fire hazard. I have a Maytag dishwasher and dryer, love them both. Maytag should stick with dishwashers and laundry. I never have been more dissatisfied with a major appliance. I would NOT PURCHASE THIS PRODUCT.

Our new Maytag Bravos XL machine quit just 43 days after being purchased. Purchased from Lowes, but since it was past 30 days since purchase date, Lowes could not do anything to help. Lowes directed us to an appliance repair service that they use. We had to wait another 3 days for repairman to come out to look at the machine... only to find out that a drain pump would need to be replaced, along w/ the diagnostics board since it was not working either. Parts would be ordered & were expected to arrive 3-4 days later. It has been a week later & the parts still have not been shipped out by Whirlpool. We are now on almost 2.5 weeks w/o a washing machine. I usually research & read customer reviews before making a major purchase. However, we had to quickly get another washing machine & dryer, so felt like Maytag was a SAFE choice since I had Maytag several years back. (That Maytag was your basic washing machine w/o the bells & whistles before machines had bells & whistles.) Will I purchase another Maytag again after this occurrence? Probably not. In fact, I am so aggravated & frustrated at this point, that I would love to just throw the machine out in the middle of the street!

We purchased this washer 3/25/15 for $873.77, we also got the matching dryer, for the same amount. This washer, never washed good, it is simply a bad design, I dont know, what type of mind altering products the designer was on at the time, but it must of been some good stuff, since all brands jumped on the wagon. This is a POS, I have contacted Maytag, and they just ignore me. We need a class action lawsuit against them, they think they can take our money, and laugh at us.

I have a new Centennial Maytag dryer. What a horrible sound it makes when the time is up!!! I had another Maytag dryer for 19 years and it did not sound as obnoxious as this new one. HELP!! I can tell some man invented it.

Just when you think that youre able to do laundry. First, comes the musty smell. So, you clean cycle your HE machine using only the cleaning product directed by the manufacturer. Then, comes the pump being stuck on. Like it still have to drain yet your clothes are soaked but you heard full force of a good drain. Poof. Unplug and kick it. Look on YouTube and discover you should take it apart and clean out some obscure puddle holder & look! You discovered where the sock monster lives...its gross. Going to start my own business (125.00) to clean these things out. Hopefully not get some kind of fungus from the grossest mold ever. Its Maytag not a Home Depot issue.

Bought Maytag dryer in December 2016. Worked fine for first 3 months. Then blue coloring showed up on back of drum and came off on white clothing. Had tech come out. He took pics and send to Maytag. They said it was normal. Further talks with customer service brought statements that we caused problem by drying blue jeans. Funny we never had. They just continued to say this discoloration was normal and we did something to cause problem and nothing they could do. But at least they were sorry for our problem. Whirlpool does not stand behind products. Dont buy.

Just bought a Maytag Bravos 4.3 cu ft washing machine from NFM. The first machine delivered was broken it didnt wash or spin the clothes. NFM sent out another one at 9:30pm. It doesnt spin the clothes out well & loads have to be small. Poorly made.

My husband and I purchased our Bravo washer and dryer from Home Depot about 5 years ago. They have been the worst ever. Clothes always tear and we continue to receive an F1 error every time we try to wash something. I dont have the money to buy a new one, but I sure wish I did. I will never buy a Maytag anything ever!

If I could rate it lower than 1 star, I would. We bought ours new in 2005. Within 6 months, the main pulley for spinning the drum fell off not once but thrice. The repair tech said that the shaft was machined incorrectly at the factory and the bolt that would normally hold it on was backing out. The 3rd time it happened was close to the end of the warranty and the tech could not make it out before the warranty date. When he did show up, they wanted to charge us. I wound up putting the part in myself. Two months later, the suds alarm came on, which caused the water valve to open. The pump kicked out and the water valve stayed on flooding my basement and the electronics in the washer. This happened twice. The second time was a week ago and I tossed the ** out to the curb. We also have a Maytag Gemini double stove which does not work either. This is the second and last Maytag appliance that I will ever own. They are junk!

I bought this Centennial washer about 7 weeks ago and it has worked right for 4 of those weeks. The washer wouldnt spin the clothes and they came out soaked. Service guy came out and said it was the computer panel and he didnt have one. So I waited over a week for another service call. He put that one and said that now the transmission was shot and he didnt have one, another wait. This is a piece of junk. Do not buy Maytag or Whirlpool products. I had a Maytag for 15 years and had one service call. They are not what they used to be.

I own a Maytag dishwasher model number MDB7749cBM 2. The panel on the dishwasher stopped working. It is only a year old. Its too new to break down. Will contact Maytag today. There are so many complaints. Why not a recall?

We purchased a Maytag Dishwasher Model #MDBTT60AWW3. Shortly after manufacturer warranty ran out, the control panel went out. Luckily we had purchased the extended warranty. The repair company came out and put a new control panel in it. Two months later, the control panel goes out again. The warranty firm sends out a different repair company. They replace the control panel again. This time it doesnt work. They replace some of the buttons as according to the repair person they arent registering the correct OHM reading. It works again. Yay!. A week later, its not working again. The repair company is coming back. This is really starting to get old. Between the multiple times it has broken down, waiting for the repair company to come out, diagnose the problem and order parts, we have been without a dishwasher for approx. 2 months the multiple times it has broken down. Im so fed up with this thing. I also will never ever buy another Maytag again. They need to have a major recall on these because of the terrible, terrible control panel. This isnt just me, its a lot of people.

Purchased a Bravo set 5 years ago. Paid $730. For the washer. 4 repairs in 5 years. It is now has a bearing out and that will cost $450. MAYTAG used to be the best... buyer beware!

If I could give this a 0-Star rating, I would! I cant believe Maytag would make such an awful washing machine! Within the first 2 weeks I called their service department because (in my opinion) the washer wasnt washing properly. It took over a month and several calls to get someone out to look at the washer & dryer. According to the technician, both machines were operating properly. Apparently the washer is designed to destroy clothing and bedding! The gentle cycle set on deep fill will add just enough water to get the clothing wet, then agitates for about 10 minutes, then it fills up, agitates for 3 more minutes and drains. During the 10 minute dry-run, I watch my clothes get destroyed! I have never seen anything like this! My sweaters are shredded, my tops are pilled up & in a garment bag this thing managed to destroy a sports bra! This machine has ripped my mattress cover in several places and pulled my sheets from excessive rubbing due to not enough water. And what is up with the slow fill? The technician informed me that the trickling water is also normal. If I could return this washer, I would! I will never buy another Maytag because my Bravos washer died after only 4 years, and this one is brutal!

Purchased washing machine, with insurance that was offered to me 9/17/10. May 2013, control panel went. June 2013, dial switch went. July 2014 washer motor drive & belt drive had to be replaced. August 2015 is broke again. Will never buy Maytag again.

I have been buying Maytag washer & dryers for 40 years. Have always been satisfied until now. The first 2 sets of washer & dryer were great. Very little ever went wrong. Now I have purchased another set approx. 3 years ago. As of today, I will be putting approx. $300.00 in repair to the washer. Repairman said it is a bad design. It is the second time for the same problem, which was repaired a year ago! I will not buy another Maytag product if they cannot be reliable. I should not have to pay $300.00 in repair for a 3 year old washing machine. I am very disappointed.

Hate my Maytag Centennial Commercial Technology washer. It takes well over an hour per load. Clothes come out very wrinkled, and my knits get holes very quickly. I would not recommend this machine to anyone. In fact, I warn people against it as I have been frustrated every single time Ive used it. Model # W10420382A.

All of a sudden, the lid lock light is flashing. The washer is only 1.5 years old!

In July 2012 I purchased a Maytag BTM standard door refrigerator from Home Depot. Approx. 2 weeks from the 1 yr. Standard warranty July 2013, my refrigerator started cycling like every 20 minutes and loud popping noises started occurring. 1st service tech would only stay 15 minutes & did not want to stick around to hear the noise. Ran the standard tests and said everything was fine. That was around Aug. 2013. So I put up with it for a few more months and finally the popping noise was getting louder. 2nd service guy (Jan. 24, 2014) got to hear my video recording of the refrigerator cycling and loud popping noise. He replaced a bad dul part (Note: they all wanted to blame it on our ice maker that we never ever hooked up). Oops...wrong diagnosis. Whatever he replaced stopped the constant cycling pattern but now the popping noise is getting even louder like a shotgun going off. 3rd repair guy (Feb. 20, 2014) tells us that is normal and recycle product material is not that good nowadays?? I pay a $1000.00 for a noisy refrigerator and they say it is a normal sound. I dont think so. The refrigerator is now popping so hard that the right side of my refrigerator that faces the open is now buckling due to the compression of the heating and cooling which is causing the loud popping noise. If you rub your hand down the side of refrigerator you can feel the waves forming on the side of the refrigerator. Trying to get a Maytag rep out here. Something needs to be done about the production of these bad appliances.

I just bought a brand new Maytag microwave a few weeks ago. The door is already broken! I’ve been sitting here 4 hours! waiting for a repairman man. No call, no show! I am missing work and gym time because MAYTAG sold me a faulty microwave in the first place! Never again will I buy Maytag products!

We bought all Maytag appliances two years ago when we redid our kitchen. I have had nothing but a nightmare with my Maytag dishwasher. It started to leak so we called in the service repair person. He said he could not find the leak but tightened something in the washer, it still leaked. We had him come in again because it still leaked and nothing. We called in a plumber to see if he could find the problem. He couldn’t find anything wrong with the plumbing and thought it might be the washer door seal. The washer is still leaking, it will be the third time the repair man is coming to fix the washer. At this point, I just want to get rid of my two year old dishwasher. I will Never buy another Maytag product. This ordeal has been a nightmare with no help from Maytag service centre. So, so, disappointing.

When our ice maker (Model # MF12269VEM10) stopped working, we contacted Maytag, only to be told that the 1-year warranty had expired. So we had no recourse but to contract a repairman. He replaced the valve (and in the process, because of Maytags decision to use plastic tabs instead of screws, the tabs for the filter housing broke off in his attempt to reach the rear of refrigerator where the valve went and we had to pay to have the housing replaced, also). The new valve did NOT fix the problem. Water continued to run out of the water dispenser after you removed your glass. We re-contacted the repairman who returned and proclaimed that there was air in the lines and it should work itself out over the next several days. Yet that night, I noticed drops of water running down the control center and filling the drip tray. I placed a towel on the floor and emptied the drip tray several times that night, before turning off the ice maker completely the next day.Unhappy with the original repairman, we contacted another who came out and discovered that the new valve was leaking from the top. That is when the filter housing broke and we had to use duct tape to hold it in place while the new repairman ordered a replacement. He tightened the valve and cycled the ice maker several times only to discover that the water overflow switch on the ice maker wasnt working, thus water was overflowing into the ice maker container. He turned down the water pressure to the refrigerator, and we tested it again. All seemed to be well until the next day when no ice was released from the ice dispenser. When I removed the ice storage bin, I found everything frozen from water overflow. I turned off the ice maker entirely and contacted the repairman, who ordered a new ice maker, which took about a week.After the new ice maker was installed, along with the new filter housing, the repairman cycled the unit several times before leaving. Yet by the next day, the ice in the storage bin was frozen in place again (I have pictures), and we contacted the repairman who ordered yet another ice maker. It took yet another week for the part to come in. After it was replaced, I monitored the ice container each time I heard ice drop into it. The 1st time there were a few drops of water in the bottom of the ice maker. The 2nd time, there was a 1/4 cup of water in the bottom. I immediately contacted the repairman to let him know and turned off the ice maker yet again.I find it hard to believe that a new valve, fresh from the package, and 2 (TWO) ice makers, fresh from the box, were all faulty. The repairs started on February 25th 2015. It is now March 21st and the ice maker is still not repaired. The 2nd repairman is doing his own research into the problem (for which we applaud him!) and now we ask you for your feedback as to the problem and how it can be solved.

I wish I had seen these reviews before purchasing this machine. The plastic tub cracked and leaked all over laundry floor after only 30 loads. Part is unavailable. We will have to wait 3-6 weeks for a repair. Manufacturer will not agree to providing a new machine. Machine is only 3 months old.

No problem with retailer. Problem is this top of the line Maytag dishwasher, Model# MD8895lAWW. Stinks all around. Takes long to wash and load, times are far apart and too few so holds few dishes. Dishes and glasses break because of the tine spaces. Horrible dishwasher for high price. I hate it so much it upsets me daily. All I get is a sorry from Maytag. Its not that old, only a year and a half. Why no satisfaction? I will avoid all Maytag products for life.

Maytag is a product that I would buy any time. Even uses it well last for a long time. If you want to spend money this is a good investment for your kitchen and as for your laundry get the washer and dryer. You do get your moneys worth with Maytag.

Have had this side by side for a long time and it is great. Have not had any problems with it. Also have had an Amana which we love as well. These are side by side and are frost free and never have to clean.

I bought a Maytag washer and dryer 3 months ago. The Bravo XL is simply a piece of crap. No agitation and clothes come out as dirty as they went in. It also leaves soap stains on all the clothes by since it doesnt agitate enough. Nothing is wrong with the unit, just a horrible engineering piece of crap. Ive been in manufacturing for 30 years and cant even imagine how a company like this can design, test and still sell such a piece of crap. You put a shirt on the top of the load when starting and its still there at the end of all the cycles. Just absolutely horrible. Do NOT purchase any washer without the old time center agitator post. Horrible....

Our circuit board has went out twice. The stove is not designed well. The oven vent sends hot air over the plastic panel / circuit board. It melts... The first one was under warranty and the second, only three years later, was not. This is a very expensive part and Maytag will not even talk about giving me a discount.

This is in reference to Maytag washer MVW7232HW0 that broke after 5 months. Maytag sent a technician out who claimed we needed to replace 3 parts. We waited almost a month for the parts to come in just to have the technician say that didnt fix the problem. We have been waiting a 1.5 months for a resolution with nothing in sight. Now we have to either way another TWO months for another part, buy a new washer and get refunded for the old one (but WE would be responsible for the almost $300 price difference it now is), or wait for a new washer to come in stock and Maytag will replace it. However according to them there are no washers in stock for the foreseeable future. This company has been a joke to deal with. I have everything recorded and will take this further.

This has the aqua cleaning technology, sounds real good. DOES NOT WORK! The cleaning is done by you as you nearly climb into the oven with a plastic scraper which they supply to scrape prior to the cleaning cycle. Then after you have used the distilled water in the bottom of the oven during the cleaning cycle (steam), you climb back in to wipe out the water and use something similar to a magic eraser to SCRUB the oven.Here is the real kicker....during the cleaning process, in between the glass (in the door) you develop water spots that cannot be cleaned unless you pay to have a service technician come out and tear it a part to clean it. According to Maytag THIS IS NORMAL and is proven (by their engineers without any documentation for the customers to be able to see) to be normal?? The consequence is a brand new stove will never be clean and it is the first thing you see when you come into my house. I AM EXTREMELY DISAPPOINTED!!!!

I purchased both the washer and dryer in this series. First the washer does a horrible job actually cleaning the clothes unless you set it as a bulky load and use more water. Despite that issue, after only owning the set for four years the dryer broke down. It made a terrible noise and you could not run it because it was far too noisy. My husband thankfully bought a replacement part and fixed that issue. A few months later I started having trouble with the washing machine. It freezes constantly and I have to unplug to get it working again. It usually take over 15 times to actually get it to begin to fill with water. Now it started to stop working during the wash cycle and I have to unplug it again to get it going. Most times I have to change it to another setting like rinse and spin or drain and spin to complete a wash cycle. Last night it began to have a plastic burning smell. I used to own the same washer for 20 years and only had minor issues that come with extended use. To only own this pair for under five years and have them both break down proves that these are poorly made products and you should save your money and purchase a different brand altogether. I will never buy another Maytag as long as I live if this is how well their products are made. I expect to have my appliances last longer than five years for their price. So save your money when it comes to these machines. I promise you will not be happy with your purchase. I will either have to repair the washer and hope it will last at least a few more years or chalk this up to a lesson learned and discard both machines.

I purchased a Maytag front loading Epic z washer and I paid a great deal of money for it and now I have a broken part on it. We contacted the Maytag manufacturer and they have informed me that the part would not be available for up to two months maybe 6 months. I cannot afford to buy another washer, so now I have a broken washer and need to purchase another washer until the parts come in. I would not recommend this washer or dryer to anyone ever.

Had previous Maytag for years. Good, reliable, easily repaired product. Cycle sequencing very recognizable. New washing machines are ridiculously designed. Neither you nor the repairman have any idea what the cycles are or if they are even working as designed. Many cycles start out trying to wash with little or no visible water in the drum (top loader). The clothes come out tied in knots. I now wait for the agitation to start then pause and add water for three to five minutes then restart. What a nuisance. I have called customer care many times and they are courteous but not very helpful. This machine is an engineering nightmare. If I were in charge I would retire the people who dreamt up this contraption and get back to something reasonable before all their credibility is lost FOREVER!!

Two and a half years ago I bought a Maytag dishwasher thinking it was time to upgrade from my Ge. After a year and a half the control panel went out in in it! So For a little over a $100 I replaced it. Now, a year later, the panel has gone out again!!!! What is this? Every year I have to spend over a $100 to repair this thing!! I think it is time to find a new dishwasher!

In the winter of 2007, we remodeled our kitchen and bought all new Maytag appliances. They cost a little more but we felt that we were getting a good quality product. Within months, the handle on the freezer became loose and I had to call for a repairman to tighten it. He told me we should buy the extended warranty because only a trained repairman could fix the handle. That turned out to be untrue thankfully because if it was true, I would have to call for repair at least once a month. The handle is constantly coming loose. A few months later, the microwave would turn on when the door was closed. I called repair as it was still under warranty. After he removed and replaced the door, I was told that we have to be careful when we close the microwave. There was nothing he could do to stop the problem. Approximately three years after we purchased the appliances, we had a problem with the dishwasher. We could only use one function; the others would not work. We were told by the technician that we got water into the door where the controls are and ruined the motherboard. I never heard anything so absurd. I have had a dishwasher in the same place for 25 years with no mishap. The cost of repair was $800. A few months later, we had a problem with the large burner on our cooktop. The outer coils heat up but the inner coils do not. I have yet to call for repair because I do not trust Maytag. Now, our microwave does not work. My husband used it to make popcorn with no problem. A little while later, I tried to heat a cup of coffee and it would not heat. The keypad works, the light comes on in the microwave but the motor does not run. Needless to say, we are very unhappy and will never buy another Maytag appliance. I wish I would have read the reviews before we purchased the appliances. Two of our friends had their kitchens remodeled at the same time we did and they have not had any problems with their appliances. But they didnt buy Maytag. I guess thats why.

Is there any place to give a zero to this Maytag Front Load Washing Machine Model MHW5500FW1 and if there is a class action lawsuit please include us! We have owned other Maytag Washing Machines and never experienced such an epic failure as we have with this washing machine! We were so excited when we purchased our new Maytag washer/dryer set in March of 2018 we even remodeled our pantry/laundry room to accommodate them! As the chief operator of the washing machine, I have literally cried at what a mistake weve made! We have no complaint of the Maytag dryer. Let me describe my new normal procedure for laundering a load of clothes. First, load the washer with clothes then press power/cancel then press rapid wash let the clothes get HOPEFULLY saturated with water then hit hold to start and then hit power/cancel this shuts off the washing machine. I then press power/cancel again and select normal and the water empties out of the washing machine from the prior load and then starts to refill, if the add a garment light comes on (when it wants too) and no I dont change any pre-set settings I am able to add extra water with a pitcher, if this procedure works I let the washer run its 1-hour and 48-minute cycle. If not, I have to start over again because the add garment light wouldnt come on to allow the door to unlock. After the clothes are finished I again press power/cancel then hit rapid wash put my fabric softener in the dispenser press hold to start and let it run its 36-minute cycle making sure my clothes are rinsed appropriately and not stiff because of the lack of water. I neglected to say that when Ive tried tricking the washer and think I am able to add extra water, if Ive added too much the sensing kicks in and the washing machine drains all the water out on its own and refills with the little water it allows! Which is maddening! I throw up my hands and sit down and cry!!! I have contacted Maytag/Whirlpool complaining about the lack of water and their wacky water sensor! I asked them how can you conserve water and electricity when you have to wash your clothes over and over with long wash cycles? This doesnt make sense! My white clothes are now dingy and stiff as well as the colored. Maytag says you can use powdered detergents if its HE High Efficiency powdered detergents, but thats not true. The detergent doesnt dissolve and ends up on the clothes at the end of the long wash cycle because of the lack of water! From the beginning I adjusted the amount of powdered detergent for the front load washer and have to dissolve it in hot water prior to washing and hopefully am able to add it to the clothes if the add a garment will let me! I have now resorted to extra cycles to rinse out any remaining detergent hoping my clothes will be soft and fresh smelling. I had planned to replace my old Maytag agitator washing machine with this piece of junk front loader, fortunately we kept our old washing machine as a back up!

Purchased a new side by side American made Maytag refrigerator (Model: MSD2559XVEB ) in August 2010 from Best Buy. Just returned from a 3 week vacation and the refrigerator died shortly after we left on trip ( 14 months post purchase date ). $700 worth of food ruined.

My $1,500 Maytag double oven Gemini has been trouble from the get go. 1st, trying to broil something cannot be adjusted. It sits 3 to 4 from the fire & there is no 2nd shelf. The control knobs sit on top of the stove & its easy to burn them when cooking. The broiler has always smelled like its leaking gas. Plus, the bottom oven stopped working & we had to get it repaired. The last straw was when the control board went out. We arent even going to try to repair, just going to buy a new stove. No Maytag!

I have a Maytag Bravos XL and have white residue on all the clothes that get washed in this machine since I purchased it. I have always used HE Detergent and have followed all Maytags recommendations to reduce the white residue to no avail. I had to wash my clothes 5 times to get the residue off of my clothing and 4 of those were without any detergent and on all temperatures and wash cycles. Model # MVWB835DW.

Neptune washer maxima XL steam - Our machine is only 2 years old and we feel the soap dispenser is defective. That little door inside to choose either liquid or powder is not flush with the basic cup and to make matter worse, there is a V shape hole at the bottom of that little door. Meaning, fill it up, and while you are looking for the softener in your closet, all the expensive liquid HE soap is on your floor! And when you close the door, if you wait for starting the load, all the soap goes into that rubber gulley instead of being sent over the clothes. I just got off the phone with them, they wanted to send a technician AT MY EXPENSE - when I do feel it is a deign mistake, not a use/abuse on my part. I proposed instead to send them a picture. They refused. I proposed to send them the soap drawer, they refused as well. I will never buy Maytag ever again and dont recommend to anyone to go to this Brand name!

When purchasing new, sales person highly recommended Maytag products. Maytag Dishwasher MDB7749SBW3 - This had the SS tub that my wife was looking for. Now only 19 months later it has completely stopped working. A few weeks ago the lights on the control panel would randomly come on or not align with the wash option that was chosen. This lasted a short time, and then lights on the panel would stay on, and not allow you to choose any options. I reset our breaker and this alleviated the problem for another week or so. Then it stopped working all together. A quick Google search and it was obvious Maytag has a MAJOR and KNOWN issue with this model. The ribbon going into the faceplate/ control board sits directly behind the port that exhausts the steam. This ribbon over time becomes corroded and eventually malfunctions. I called customer support. They were completely unwilling to acknowledge the problem and also unwilling to help in any way. They offered to sell me an extended warranty @ $329.00 that would cover the service call and repair. Very unhappy that their product has an obvious defect/ flaw and they are completely unwilling to acknowledge/ or stand behind their product. We are a family of (3) and run this dishwasher about once every 5-10 days. Unbelievable they find a fail rate within a year and half with light use acceptable!

I purchased this washer from Lowe’s on 8/9/2017. After 3 years and 2 months, this washer would no longer power up. I tried resetting it by unplugging it and lifting lid 6 times. It didn’t work. The extended warranty from Lowe’s expired on 8/9/20. I called a technician and he found it need a control panel and control board. He suggested that I call Maytag to see if they would give me the parts as a courtesy since the washer was only three years old. I contacted them and experienced long wait times (51 minutes was the longest). I spent a total of 3 hours on the phone with them. They said no there was nothing they could do for me since the manufacturers warranty ended 2 years ago and the “mother control panel” doesn’t fall under 10-year motor warranty. Well, there’s no need for a motor warranty if there’s no power to the unit! The cost of the parts would be almost $600. It is shameful to not stand behind your product. I would expect to have to replace an iron or a juicer after 3 years, but not a washer. This was a major blow to how I would view the way they do business. I purchased the extended warranty from Lowe’s. I will never do that again. It was a waste of money. They didn’t make any concessions for me either. They kept saying it was a manufacturers issue.

Purchased this machine to replace the recalled Samsung washer that was exploding. I should have kept my Samsung. I loved it and had no complaints, but since there were reports of it exploding I took the rebate and purchased the Maytag Bravo Nightmare. Everything you have read or will read here is true. I would spend hours, I mean hours trying to do a load of laundry. If the cycle would complete itself, the clothes would be soaking wet, and they never smelled clean. I would try rinsing again and the cycle would start out with 18 minutes and I would return to the machine 1 hour later and it would be still running water and still have 18 minutes or more left. I watched it complete the spin cycle and start the rinse cycle again. We had the service guy out several times - he would call the techs and they would test the machine and say nothing was wrong other than it was off balance. They said I was using the wrong detergent - when proving that I was using an HE detergent, they counseled me on how to lay the laundry into the machine, and said I was using too much laundry detergent. After babysitting this machine for more than a year, and being told by Lowes Customer Service that the techs say there is nothing wrong with the it, I was fed up. I called Lowes and told them to send their techs to my house to do the laundry. I threatened to call for service every week until my extended warranty was exhausted. They finally gave me a merchandise card valued worth the purchase of the machine. Now, I have the painful decision of deciding what to buy next - It wont be a Maytag!

Maytag Model #MGR7662 range - We inherited this oven when we bought my mother-in-laws house 2 years ago. We had to get a thermometer to keep in the oven since the temperature is never consistent and is usually 50-100 degrees lower than the digital readout. We will be replacing this oven as soon as we can and it will NOT be a Maytag.

I purchased a Maytag Bravos XL Commercial Technology top loading washer, model # MVWB850YWO, in May 2012 and it was delivered in August 2012 due to a home purchase not being consummated. Anyway, I bought this washer and the matching dryer at Lowes and purchased a 4 year extended warranty with Lowes. This would cover me with a warranty through August 2017. I had some problems with the washer while under warranty and had it repaired at least twice. I have had, and still do, have a water leakage in the washer. The water when dispensing into the detergent compartment splashes over and you would think it would just go into the tub. Someway the water leaks down the inside of the washer and runs out onto the floor also causing rust to the inside of the front panel. The resolution was to turn the water pressure down on the supply lines. When this was done, the washer would quit running due to not enough water being dispersed into the drum. A replacement seal was installed and I still have the same problem. The repairmans final resolution was to put tape over half of the detergent dispenser to hold the water in the detergent dispenser and still allow me to put detergent in the dispenser. So, a towel is in front of the washer to soak up any leakage. Now, just 5 months after the extended warranty expired, the bearings under the wash tub are starting to roar during the spin cycle. I contacted Lowes service again and basically I am out of luck. The repair cost is expensive, the part and requires 2-3 hours of labor. I decided to chuck this washer and buy a new one. My wife found one that has an agitator, unfortunately another Maytag, and wants it as she has said the Bravos washer never seemed to get the clothes clean (due to not having an agitator). When checking online for references on a new washer and any recalls on my current washer, I discovered other Bravos XL owners having the same problem with the bearings in the tub. I contacted a local business to try and sell it to him for cheap and when I told him what was wrong with my washer his reply was, I have one just like it out back with the same problem. Dont need two problems. Cant even get rid of a Maytag washer due to it being junk. Many other reviews have listed problems with Maytag products especially since Whirlpool bought them. The Maytags of today are not your parents Maytag. Used to be the Maytag repairman sat around his office waiting for repair calls. This has changed considerably since Maytag sold out to Whirlpool. After doing some research, it seems Whirlpool has bought just about every company selling washers and dryers and are making them as a disposable item. I would advise not purchasing any product that is under the Whirlpool corporate umbrella as I feel whatever they buy, even a superior product like Maytag, they cheapen the product and try to benefit from the name, as in the case with Maytag. So, no more Maytag or Whirlpool products for me until they have proven they can build a quality product once again. Hello GE!!!!

I bought a Maytag washer 6 years ago. Energy saver. Less water. Nothing ever seemed clean. Always white streaks and I used liquid detergent. So we went out and bought another Maytag with agitator June 2017. Never drains properly. I will never ever buy another Maytag product.

My microwave started acting up, after about 5 months. It would not cook a complete cycle, without an error saying that the door is open, and needs to be closed. The repairman has been out 5 times already, and the problem is still not corrected. Maytag/Whirlpool has said they will not replace item, then they decided they would possibly replace at a pro-rated amount. So, I have to purchase a microwave twice, to have one that works? Somehow, I feel Im being taken for a ride in this deal.

Maytag French Door Refrigerator (Counter depth) #MFC2061KES14 which cost over $2,500 dollars is a DUD and the company is EVIL. The freezer leaks all over the floor and the company will not stand by their product. When I called the company they said they have had to upgrade a part called the drain tube kit because of this problem but did not put a recall. They know that this problem will occur just about the time the warranty runs out. I bet the wife of the CEO of this company has a very expensive good brand of refrigerator. Stand by your product and pay for the repairs and labor to get it fixed and put out a recall. LIFE IN AMERICA!!!

I remodeled my kitchen, put in all new Maytag Almond appliances washer, dryer, stove, refrigerator, dishwasher and microwave oven. I was pleased with everything but the stove. The stove was $800.00. The oven caught fire three times and smoked up my house. I replaced the stove with another brand, cheaper and safer. I moved to a new house, five years later, bought all Maytag appliances stainless steel. The hinge on the deli tray broke, the inside is thin plastic, not covered in extended warranty. The stove caught fire (I didnt learn the first time around)! The microwave has a thin, bendable, plastic rack, the handle snapped right off. I cant buy a handle separate from the door. Now the microwave wont heat! My dishwasher was recalled. The heating element could have caused a fire! Nothing that breaks or malfunctions is covered by warranty. Who needs to pay for a warranty too and get no parts or service rendered! I will buy all new appliances and when I do, it wont be anything Maytag makes and none of their other brands! This stuff is very expensive garbage! Somebody please initiate a class action suit!

I purchased a washer & dryer from Lowes on December 3rd. On February 20th, my washer stopped filling up. I called customer service and had someone come out a few days later. The repairman said the sensor broke & it would take 10 days for part to come in. After 2 weeks, I tried calling repair company and they would not answer phone for Maytag, or me. Maytag called another service provider, and it will be another week before part comes in. Never could get in touch with anyone who was helpful! Now it’s been a month, and still not fixed!

So our 4 year old Maytag Dishwasher just took a crap. Thank God we were at the kitchen table when it started to smoke, which smelt like burning wires and unplugged it immediately. Repairman came out and said it would be a 3 to 4 hundred dollar repair. What happened to the great 10 year Warranty? Oh yeah, its a limited warranty which does not include wiring. Could have burnt down my 4 year old home, but thats ok, not covered. The good news, the upper arm I replaced due to wear and tear would have been a free repair, because it would have been covered! No more Maytags in this home, ever!!

We have had a Maytag Bravos XL top load washer less than a year. Big Mistake. It was JUNKYARD ready when it came out of the box. Does NOT wash clean. Weve tried everything.The agitator looks and acts like a toy. Will not run enough water to wash anything. We had a LG front load before and its hard to get use to having dirty clothes. NEVER AGAIN.

Worst customer service ever. I ordered my washer and dryer from home depot 2 weeks before a possible delivery day. The day before delivery I receive a call that they dont have them and I must wait 1 more week. After 3 phone calls I am promised a credit to my account. A week after delivery I am wondering where my credit I was promised is so I call. Im told the most I can be given is $100. I state that I feel my time is worth more than that. A supervisor is brought in and Im told we will get $150 credit. Then put on hold. She reviews account (why didnt you do this first) and told because we didnt call within 48 hrs of delivery the most they can give us is $75. So I call back very frustrated. Then Im told its our word against theirs that we were offered that?!? What?!? Well I am sure you record conversations and thats total BS. I explained how you cant offer something then take it back. I was told the week before I was getting a credit and my account already notated. No one said, Call within 48 hrs to dispute again to get it. Why would I have to I mean seriously. So after a total of at least 2hrs on the phone before and after delivery I am forced to settle with $75. I feel very unappreciated. I purchased and paid for $1633 worth of appliances that were a week later than promised. Called less than 24 hrs before expected delivery and told they dont even have them. Then told Im getting a credit of $150 to be told sorry now just $75. The lady proceeds to say that she doesnt think it was because of the phone call not being made. What? Are you serious. WELL THAT WAS THE LAME EXCUSE I WAS GIVEN SO I COULD CARE LESS IF IT WASNT THE REAL REASON. THAT JUST MEANS I WAS LIED TO. I promise I will never buy Maytag Whirlpool again. One customer may not mean much to you but good customer service means everything to me.

It does not completely drain all water out of until. So unless your running the washer every day, you will end up with the most horrible smell coming from standing water. It is very irritating and so fowl smelling.

Discovered that thousands of others are having problems with the control panel on their dishwasher. Mine is Model # MDB7749SBM2. Looks as if I should just junk this horrible product and buy a new one (another brand, of course). My biggest concern is that I purchased other Maytag products along with this dishwasher, ie, a refrigerator-freezer, a built-in stove top/oven and a microwave. I have had a service call on the fridge (water line), the oven (gas) will indicate a set temperature (400 degrees for example) sometimes it will only be abt 200 degrees via a portable thermometer... Sometimes it doesnt ignite at all (have to reset it 3 or 4 times, the microwave has issues with the digital readouts, and on and on and on.I have only had these appliances about two years (after warranty expired) when each unit started exhibiting problems. I paid $175 for the fridge repair and am now considering biting the bullet & replacing everything as MAYTAG/WHIRLPOOL apparently isnt going to take responsibility for any defect on ANY OF THEIR PRODUCTS! Im 75 years of age, retired and cannot afford the replacement route but it looks like I dont have a choice unless someone has a better suggestion. I dont have the skills or energy to attempt the repairs myself.

RE: 5.2 CU Ft Top Load Washer, Model # MVWB865GW0, Serial # C84370937 - Purchased Jan 2019. The clothes come out terribly tangled and severely wrinkled, even when using the Wrinkle Control or Delicate cycle and occurs in every load size. Ive tried every cycle, including the deep fill and low spin speed but items are so wrinkled that whether I lay flat or hang or put them in the dryer, I have to iron them, which I never did before.

Control panel is defective on my Maytag dishwasher. Found a phone number that was created to deal with this problem. I only had to hold for a few minutes but the first person I spoke to was rude and unhelpful so I asked to speak to someone else. When another agent came on the line I told her that only the normal and rinse button light up but do nothing when pressed. She arranged for a repairman to come to my house and determine if my control panel is defective at their cost. When he arrived he asked me what the problem was and I said, The touch pad control panel is not working. He stated, Your control panel needs to be replaced. I have to order the part and come back to fix it. He was there for about five minutes and he never laid a finger on the dishwasher. When I asked if the control panel design has been fixed he said, No, you will probably have to replace it again.There is a video on the internet that shows how to seal the electronics with silicone. The repairman said that they cannot seal the electronics unless Whirlpool provides a kit to do it. I guess the Maytag repairmen may have to come out of retirement. My husband will seal ours after it is replaced so we hopefully dont have to deal with this problem again. So now I am waiting to see if he returns in a reasonable time frame and gets my dishwasher going. There is a class action suit about this issue filed in 2013 about this defect.Updated on 09/23/2015: A repairman came to my home on August 20, 2015, at Whirlpools cost, and he determined my touch pad did not work. He informed me that Maytag would provide the part, free of charge, but it would cost me 85.00 for them to come back and install it in 2-3 days. As of today I am still waiting for the part to come in, apparently due to high demand Maytag was out of touch pads, which were out of stock. No idea of when that would be, the repairmans company said, dont call us, we will call you when the part arrives. So I began to look for the part myself, found a couple on an auction site, but most companies that sold parts were on backorder. Until I found a company that said their inventory was out of stock but they had five, stashed in the back. The price of 105.00 was not that much more than the 85.00 cost for the service call. Got it in two (2) days, installed (in about five minutes), sealed by my husband and I loaded it and washed my dishes. I was so overcome with relief, tears came to my eyes and I almost fell out. I give five star to the fella that had the part stashed until I needed it.The Maytag repairman is still waiting for the part so he can fix my dishwasher.

Horrible Refrigerator MSB27C2XAM00. I bought this refrigerator November 2013. Over the past 5 months I have made over 10 calls to Maytag customer service. Each phone call averages 30-45 minutes in length. In total I have and have had 6 service repair visits. Within 4 weeks of acquiring the unit, the letters on the ice/water dispenser wore off. They replaced the panel and within 4 weeks the letters wore off on the replacement panel. The subsequent calls made to customer service were regarding slow water dispensing and shrinking ice cubes. I was advised in order to maintain water speed and decent sized ice cube production I would have to replace the filter every time the water dispensing slows, which is on average every 4 to 6 weeks (each filter costs $40).When I asked why I would have to change the filter so frequently when the packaging instructions with the water filter states you can expect an average of 6 months use or 200 gallons, (mind you we are a family of 2 adults and one child under the age of 10 surely not consuming 200 gallons of water within 4 weeks), Maytag advised me to attain a whole house water filtration system. I was told that the water supply to my home must require extra filtration which is why the filters are not lasting. I asked if other NYC residents have made such complaints. Maytag advised they cannot share this information for confidentiality reasons. I told the rep that I did not want specific names/address of the complainants. I just wanted to know if there were any other similar complaints! If its the NYC water supply I would have to believe there would be similar complaints. Maytag would not advise.They will not budge in replacing the unit. After spending $1,400 on this refrigerator I am now expected to invest $500 annually on water filters in order for the refrigerator to work properly. I was also advised that if another service tech came to my home and the issue was found to be the same I would be responsible for payment of the service call. I did my research before purchasing this Maytag product. I ultimately selected Maytag for their reputation. I am so disappointed with this unit and with the company that I will never purchase another Maytag appliance and I will advise everyone I know to never purchase from this company again. Such a disappointment!

I bought a new refrigerator and when I plugged it in would not cool. I called and the authorized tech came and said the compressor was bad and the evaporator was rusted and hoses were greased up. I have now been informed that the warranty was void because it was put in a dental office and not a single home. I said since it was never used I would put it in a house. They said it was void and I was out of luck. I always thought maytag sold good products but this has convinced me to never buy a product from them again. It never worked and the tech said it should be replaced but they said he should never had told us this.

My machine is only 14 months old and will not even turn on. I opened the lid, and the tub was filled with water and the wet clothes sitting in there. There were only 6 items in there: 3 school skirts and 3 school pants, dripping wet. So I unplugged the unit to try and clear the circuit board - to no avail. The machine will still not turn on. The lights are on, the sensor turns on for about 3 seconds and shut off and everything just sits there. I did not get the extended warranty. My mom still has her Maytag she bought 30 years ago and its running like a champ. Wish I could say the same. I gave my sister my old Maytag - its 25 years old and its still running like a champ. This machine is a LEMON. I will never buy another Maytag again. I am so done with this brand. I hope that a Class Action suit is filed against them.

Purchased a new top loading HE washer in 9/2012. This machine gets very little use - approximately 10-12 loads a month. It is now broken awaiting parts which will cost about $200. Of course the warranty is only good for 12 months There is no excuse for a washer this new breaking and costing this much to repair. What a piece of junk! Avoid all Maytag products.

Maytag Refrigerator Model MFI2665XEW6 piece of junk. * Builds up ice on bottom of freezer * Bottom freezer door will not close * Annoying alarm sounds* Water leaks on floor

We bought a Maytag dishwasher on 9/22/2012. Model number MDB7759SAB. Within the past couple of months, it has been very temperamental. The control panel started beeping continuously and some of the functions wouldnt work anymore while others continued to work too well; in that the dishwasher on occasion would rewash several times without anyone starting the machine again. The dishwasher also started leaking water... As of yesterday, the dishwasher control panel stopped responding and then out of the blue, the dishwasher turned itself on in the middle of the night! We called customer service and they said they could send a repairman out for around $89 and then we would have to pay for the parts needed and the cost of labor. After reading many reviews sounding exactly the same as mine, my husband and I are against repairing this lousy machine. Its absolutely ridiculous for a dishwasher to quit unexpectedly like this. Our question now is, which brand to purchase for our next dishwasher? No more junk please!!

Seven years ago when we bought a new house, we bought all new appliances, Maytag Washer and Dryer, because they were suppose to be extra good and sturdy, what a joke. For the past four or five years, I have had to replace the lock on the door of the washer, which means Im without a washer for a week. Since no one stocks the parts because it is such a joke, some repair places wont even consider repairing a Neptune. Seems like since the company stopped making them because of the problems they have, as a minimum they should replace all Neptune washers that have been sold with a reliable washer, front loading in the same price range. I will never buy another Maytag product and will be sure to tell everyone I know not to buy them either.

I can honestly say that my Maytag refrigerator is indeed the worse appliance that I have ever purchased. This is how it rolled... I bought a new Maytag stove, frig, microwave, and dishwasher in June of 2006. Here is what I am now dealing with... the frig went on the fritz 2 years ago (warranty expired). The problem being the freezer would not automatically defrost. Because of this the coils would ice up and this prevented the cold air from moving from the freezer into the frig part. Things remained frozen in the freezer, but everything became warm on the other side, the frig side. I had it repaired about a year and a half ago to the tune of $165. Then about 6 months ago the problem reoccurred, but instead of paying for another repair I figured out that if I used my blow dryer I could defrost the ice from the coils on my own.Unfortunately, the problem reoccurs more frequently now and I have to manually defrost the coils almost every week. This past weekend things finally came to an end as no matter how many times I manually defrosted the coils, it would be fully iced up again with an hour or so. Also, all the time it is acting up it just sucks up electricity, and I have notice a spike upwards on my energy bill. It must be related to the frig. So, I bit the bullet and bought a used frig on craigslist just to hold me over until I have time to do research on what appliance brand is indeed reliable. I should of done this before I bought my Maytag appliances from Home Depot. As far as my other Maytag appliances, here is their current condition. Microwave about the stove: the handle broke off a little less than 2 years after purchase. Stove: now has rust on the front of stove, at the bottom of the stove which is a pull out drawer.Dishwasher: not working at all. The start button doesnt work. Normally, you just push the button and a green light comes on and it begins the first cycle. This is no longer happening and no green light comes on. Refrigerator: Took it to the dumps this morning to be recycled. Cant believe it, all of these appliances are nothing but crap and I will never purchase another Maytag. I have shared my experiences with all my family and friends and have encouraged them to avoid Maytag, as it is not even close to being the product it used to be. Another piece of junk coming from somewhere other than here in the USA. We lose jobs here in the US, and then end up buying the goods from another country that makes inferior products. How stupid can we get!

The big problem is Lowes and Home Dopey, I mean Depot. I am an appliance repairman for 30 years. Their machines are built to a lower spec. Buying same machine from mom n pop store will help! Will cost you more but it will last longer with less repairs! P.S., While Maytag does make some of their own appliances, when Whirlpool bought Maytag years ago they shut down the Newton, Iowa plant. Whirlpool builds that washer and puts Maytags name on it. If you want a good washer buy a Speed Queen, go online and check their reviews! One more thing, LG and Samsung build terrible appliances. Do yourself a favor and stay away from them, just saying!

We purchased a Maytag MVWB765FW top load washer with agitator to replace a Whirlpool with premature gear case problems (less than 3 years old). Was partially sold by the attractive metal label that says 10 YEAR limited warranty. It is now less than 2 years old and the Maytag selected repairman just diagnosed a failing transmission and of course advised us this is not covered by the warranty. Cost to repair—$ 600. About as close to false advertising as I have seen.I can’t believe that this company would sell such crap and not stand behind their products! But after seeing all these other complaints I believe it now. I bought both washers from Nebraska Furniture Mart and I realize they only sell the appliances but I plan to inform them that if they continue to handle Whirlpool and Maytag products they will never sell another appliance to me or to anyone else I can influence to not buy from them. We as consumers are almost powerless against these manufacturers but if we can influence the stores we buy from, just maybe we will see some improvement.

My washer has always had an odor, and I clean the gasket. It gets mold on the gasket and smells horrible! Now for my dryer, it has 3 baffles inside that helps turn and fluff the clothes, and 2 of mine have broke off. And that results in clothes that look like they have been in the dryer for weeks. And I take them out as soon as they are done drying.

Two years ago I purchased a Maytag Top-Loading HE Low-Water washer. I have always taken great pride in the way my laundry looks and smells but since this purchase, my laundry no longer smells clean and fresh nor does it look clean. I have always used the same detergent and fabric softener (only now I use the HE version) and it served me well. I have read all of the directions and did as I was instructed. I cannot believe that anyone would actually think that you can do laundry with practically no water. Do the decision makers have not common sense at all? I didnt and still dont believe it but what choice did I have when all of the machines are now HE with low water. I think its terrible that consumers dont have a choice. I have come to realize that low water, HE washing machines actually waste more time, energy and money (detergent and fabric softener).My clothes are not clean, nor do they smell good when the wash cycle is finished so I have to wash them again, using more detergent, fabric softener and energy. The super fast spin that supposedly sucks out most of the moisture, also rumples my laundry with semi-permanent wrinkles (even on the low wrinkle setting) so clothes that never had to be ironed before, now need pressing. I find it remarkable that, with all of the detergent ads promoting washing clothes in cold water to save energy, we are told that if our clothes are not sufficiently clean in cold water in our HE washers, that we should try a warmer/hot temperature. Good luck with that because my machine has several temperature settings but only uses one - COLD! I cannot actually believe that with all of the technology that our society holds, we are going backwards in the basics of washing clothes. Terrible product, terrible quality, terrible results, terrible waste of time, resources and money. Why cant you just leave some things alone??

We are a family of nine so I wash a lot of laundry. We bought this washing machine a month ago and hoped it would perform like our prior one. The problems are many. It is too smart for its own good- it requires a cleaning after every 30 washes but gives you zero warning beforehand so you will already have the clothes in and started the cycle when it will stop the cycle saying it needs cleaned. There is nothing you can do to override the cleaning cycle, so you are forced to remove your sopping wet clothes and run the cleaning cycle- wasting time and money on precious water! It also wants you to use its specialty affresh to clean it with, adding cost we hadnt planned on. Then you cant tell when to put the clothes in as it tells you to start the washer and then add the clothes, but if you put the clothes in first sometimes it wont start because it wont sense properly, and if you start it without the clothes. Then when you stop to add the clothes it wont start it with the clothes in it- which way does the machine want it?! So it is a guessing game as if the washing cycle will even start. And the washer wont hold as many clothes as our last one did. If there are too many clothes, the cycle will stop and it will refuse to wash until some are removed. Whenever there is a problem starting, which in one month has been four times now for us, it is a huge guessing game as to what is wrong for why it wont start. I dont need this kind of frustration! Further, the locking mechanism in the washer is plastic, and I know from experience that plastic parts will be the first to break. Had I realized this before purchasing, I would have looked for a metal locking device. My guess is when it does break, the whole washer will break. Also, from day one, it has made a sound that Im not sure is normal. It sounds almost like grinding gears every time each various phase starts or stops (washing, rinsing, draining, etc.). I sincerely hope this isnt a manufacturer defect as we didnt buy the extended warranty. We researched this model before buying and many were happy with it but I hate this washer! I loved my last Samsung washer but it rusted all over after just five and a half years even though it still worked great, so I didnt want to buy Samsung again so we took a chance with this Maytag. I am regretting this purchase. I consider myself to be a person easy to please. I want a washer that works that wont rust that you can put a ton of clothes in and throw it in the wash and forget about it. I dont want all this high-tech sensing stuff that just messes up and is highly inaccurate in what it senses! Why cant companies offer a simple, high quality product anymore that works, without the added costly features?! The model number is: MVW6230HW0. Avoid this model number.

We purchased at Home Depot on 5/12/2012 a Maytag dishwasher model MDBH979SAM. The following November it started not working correctly. We had to fiddle with the cancel button to get it to work at all. It just kept on getting worst to where it would not function at all. We called Maytag service. They set up a service call with a local warranty service provider who ordered a control board and a week later came and installed. No charges at this point. Now, here at the end of August 2013, out of warranty, it is doing the same thing! I just called Maytag customer service in Tennessee and was told they are so sorry but would sell me a one year service contract. This I immediately refused. I told the person I was talking to that I had seen this website and was aware that hundreds were having the same issues and that I knew first hand that they were doing nothing about it! I informed this person I will be in contact with my home states Attorney General’s Office Consumer Fraud Division and would ask for any assistance from them available. This person then offered to replace the part at no charge, but I would have to pay for the service people to come and determine the problem (real hard to figure out that it is the control board again, same as everyone else) and then pay to have them come and install it after they order and receive it! The service order left by the tech when he replaced the first board showed a $74 fee that was covered by the warranty. So from this I have determined that it will end up costing me $150 for this repair. I also realize this repair may last six months to a year if I am lucky! Needless to say I refused this last offer too. I will have to wait to hear from our Attorney Generals office. How can any reputable business do this?