Bought this machine summer of 2018 when my old washer went out. This machine is impressive looking but that’s about it. Clothes don’t get clean. Half the time they don’t even get wet! I’ve had to wash sheets two or three times to get them clean and wet. When washing jeans there is always lint and white debris on them when the wash cycle is done. I’ve tried all different settings, I’ve tried different detergents always the same problem. Wish I’d never laid eyes on this model at Lowe’s last summer. Gotta say, worst purchase of an appliance I have ever made. Don’t waste your hard earned money on this piece of junk!

This is a wonderful washing machine. For cleaning clothes it does exactly what you expect from a washer. We have had 2 Neptune front loaders. They, however, have a couple flaws I dont want to live with again and will be looking for one that has come up with the solution to them. One, the bearings on them need replaced on a periodic basis or it sounds like a 747 taking off. Two - the front gasket around the barrel has a mold problem no matter how much you try to keep the thing clean. Other than that, these machines perform fantastic.

Maytag Quiet Series 400. Only good thing is the 3 spray arms. The racks are arranged in the worst configuration so you cannot fit many dishes in. The controls are extremely confusing. They do not seem to work in a logical way. The manual is of little help in figuring out how to operate the machine. I dont use the drying feature, so the only options on the panel that work together are Normal and Hi Temp Wash. Ive never had a dishwasher that took 2 hours to wash, but the settings dont allow for a smaller load or shorter time. The rinse agent receptacle is confusing and difficult to understand and use. Way too complicated compared to earlier dishwashers that Ive used. Would not buy this one again.

We have a Maytag Neptune washer and dryer. The seal is full of mold. We replaced the seal a few years ago and I wipe it and try to clean it every load, but it is useless. I saw there was a class action suit and I was never notified of this. I would have participated. I want it fixed, replacing the seal does not work.

Bravos XL washing machine is the worst washer I have ever used. IT DOESNT GET THE CLOTHES CLEAN! There is not enough water when filling up, and you cant control it. I put a load of dog blankets in the washer and at the end, they were in the same order as I put them in; they hadnt moved! All the stains were still there and there was soap scum everywhere. Also, while I appreciate a large drum, it is so large that I cant even reach down to get the clothes on the bottom, I have to use a stick to get them up. I am so irritated that I spent $1636 for the washer and dryer (dryer works fine but same trouble with the huge drum). I got mine from Sears online after checking the Consumer Reports which put it in the top 5 washers!!! Dont buy this washer. Waste of money. Will probably just have to throw it out and its brand new.

We bought the highly rated Maytag Bravo washer and dryer in March of 2010. In less than a year, the dryer broke down and the drum drive belt had to be replaced under warranty. Last month the washer drum stopped turning. A & E Factory Service quoted $466.87 to replace the bearing that had failed. We have hated this washer since the day we got it. So, it wasnt hard to buy a Samsung front loader and have the miserable Maytag hauled away to wherever badly designed machines go. Trying to wash clothes using high speed spinning instead of water causes excessive wear on the clothes and the machine as well as tying the clothes in knots. It is one of the worst mechanical designs I have ever seen.

I dont know where to start. This machine (Bravo XL Top Load Washer) is ridiculous! When I finally figured out how to start it, it did not rinse or spin clothes. I cannot figure out how to get it to do that so Im stuck with a washer full of wet clothes. To add insult to injury, I cannot reach into the washer to retrieve them. I am 52 and all washers are designed by freakishly tall people with NO REGARD FOR WOMEN apparently! Poorly designed! Poorly engineered! What a piece of junk!

I was having similar issues with my Maytag model MD dishwasher. The unit was operating, and then the start/resume light began flashing. Didnt think much about it since the machine continued to run. But the machine wouldnt cycle off, or rinse or dry. It continued to run, with the start/resume light flashing. When I opened the door and hit cancel, the unit turned off. Several minutes later, the normal light and heated dry lights came on, and soon after, the unit started up by itself (Twilight Zone music is going off in my head). I let it continue to see what it was going to do. It ran, and ran, and ran some more. I stopped it and secured the power to it, left the power off for a very long time. Started it up, no joy.I began reading the blogs sent in by other frustrated Maytag owners, we are numerous. I went back and re-read some of the posts that dealt with resetting the control panel. The one that mentioned; press Hi Temp. then Start/Resume about 3 times consecutively, that did the trick. Thank you for that useful piece of info. Saved me 143.00 plus tax and shipping for the new control panel (for now). I found some very helpful MOs (Maytag owners). I also found something very frustrating, with so many unhappy customers dealing with the similar issue. I would think that Maytag would put out a technical alert that deals with these problems. Instead, we get these so-called Maytag experts that magically appear on your computer screen. They ask you, what seems to be the problem. So after I described the issue, I asked the Pro, how to prove that the issue is with the control panel, or the elect. control board, both parts are 143.00 ea. (Just trying to limit my pain.) They send me to a page that wants to charge me 28.00 for the answer. What an insult. We pay 500-800 dollars for these units that should last more than 4 yrs. and some doofus is charging you for answers that saves you the consumer money and frustration. I, like many in the Maytag blog, will never purchase a Maytag product again.

Maytag dishwasher model MDBH979SAM1 purchased December 2012 From Home Depot. After only 14 months of usage the front panel ceased to work. Contacted maytag about issue and they responded THERE ARE NO KNOWN ISSUES WITH THIS MODEL. After doing some research (5 seconds), I have found thousands of people with the exact same issue. Maytag has stuck their head in the sand. Either they are ignoring this issue or just dont care due to excessive cost of replacement. This is obviously a design flaw due to poor engineering and Maytag needs to stand behind their product and fix this issue. Personally we had to save up for 1 1/2 years in order to afford a dishwasher. Now we are stuck. Some people have replaced this part costing $200 2-3 times. I cannot afford to take the chance on a repair. I will have to start saving again for a new dishwasher and this one will not be a Maytag. (Less)

Maytag Neptune was purchased over 15 years ago to replace GE, which we purchased when children were little. I wanted a step up in quality. I remember paying around $499 for this unit. This is an analog unit. The intellidry feature has been a real asset, protecting our clothes from over drying. We have had this machine for nearly 20 years. It has been real reliable, sometimes drying 20 loads a week. Large capacity, but has to fit down a narrow and twisting stairway. Must be energy efficient, have good reviews and decent price. We always look for sales or buying incentives. Brand is secondary to quality. Knowledge of an appliances historical reputation is important. I would look at reviews, especially concerning cost of repair. I would attempt to get a hands-on view, before purchase from a reputable supplier at the best price. My dryer has only required one major repair in the time Ive had it. A few years ago we replaced the motor and blower, and I have personally replaced the drum support rollers twice. I hesitate to replace this machine, because the analog controls have proved very reliable.

I purchased a Maytag Neptune 24” front load washer (MAH2400a) and 24” electric dryer (MDE2400AYW) on October 26, 2005 from Sears in Chesterfield, MO. In April 2011, the drum in the washer began to slush and grind. Water also began pooling around the machine. I called Sears and arranged for service repairman. Before he even looked inside the washer, the repairman wanted to give me a coupon for $50.00 off a new washing machine from Sears. After my insistence, he finally opened the washer and told me I needed a new drum. Because of the Sears repairman’s reluctance to look at the machine, I had another appliance repairman review it and was told that the water pumps for this model were defective. Any loose items the size of coins collected inside the pump and damaged it. I paid $340.00 to get the pump replaced. Ten months later, the dryer started smoking. After scheduling a service call, I was told the heating element burnt out and it would cost $360.00 to replace. It was then I noticed that the washer was leaking again. I took the front base cover off and saw mold growing under the machine. A little research uncovered that this set of machines has had many dangerous problems, from mold to catching on fire. There was a class action lawsuit filed and won by consumers in April 2005, yet I was sold this model in October 2005. I feel both Maytag and Sears knowingly sold me a defective and dangerous product. I would like to be refunded for this set.

I bought a Maytag dishwasher Model MDB7749SBW3 from Home Depot 6/2014 and by December 2015, the touch panel was going crazy! Ive read a lot of reviews and this seems to be common for Maytags. It would cost me almost as much to have this machine repaired, with a service call and the cost of a new panel, as it did when I bought it. When talking to an appliance repairman, he informed me that Maytag and most all the major brands are now owned by Whirlpool and that they are basically junk--not meant to last more then 1-3 years! Where are the recalls and how do we get a recall started?

Im writing in reference to Model # MF12569YEM2. Bought this 3 years ago for close to 3k. Since then it forms a sheet of ice under the bottom freezer and leaks water onto the floor. It has ruined my hardwood floor and leaked through the floor to my basement and now need to re-sheetrock the ceiling. Its a bad design and should have been recalled because I see everyone else with this model is having the same issue.

We had purchased a Maytag refrigerator from a local appliance store in May 2012. The fridge was delivered in June and come August 5, 2013, it does not work. First, the temperature of the refrigerator declined drastically causing us to lose over $500 worth of food. Items that were even unopened had to be thrown down the drain. The first call was made to Maytag customer service. They decided to send a technician. Great. The technician came and informed us that it was the refrigerant. WRONG. The second technician comes and states that the compressor is shot and that is why it is not staying cold. Time to order the compressor that is on back order. Shocking. Another week goes by without a fridge. Cut to the third technician who comes and installs the new compressor. Fridge is cool and at about 32 degrees for probably 4 hours. The food goes back in the fridge and the temperature climbs to 70 within minutes. Strike two. Contact Customer Service and demand answers on what can be done. Speak with the first representative named Melinda. If you get her good luck. She states she doesnt care and hangs up. Call back to speak with another representative who is very sweet and compassionate and tries her best to help. Unfortunately, she was unable to do so. Asked to speak with a supervisor and had the displeasure of speaking with Scott. For all the trouble that we have been going through, time wasted, food thrown away, Scott can offer $100. Yeah, okay, nice try. The more we speak with Scott, he ups the ante to $150 and the final offer of $200. I advised Scott that there is someone higher than him that needs to be involved after he told me that he was the highest I could go. Wrong again. Time goes by and nothing happens. We receive a call from Yvette ** that was missed and call her back in the corporate executive office. We have contacted her and left her 4 voice mails and the response has been nothing. Actually, calling her you get her message that she is not available. This is over the span of a week. Nothing. ANOTHER technician is sent to look at the fridge and what was supposed to be a brand new compressor that was installed and states that the fridge is condemned. Well isnt that lovely?! Of course because the parts are made in Brazil and Maytag is charged $15 for them and they charge the consumer $200. There is no reason why they should work. We got in touch with the appliance store who told us that we need to speak with Maytag to ask for our money back because we are NOT taking the same fridge as a replacement. Now, we are plagued with the appliance store not taking our calls, the corporate executives not taking our calls, and a $1300 stainless steel french door paperweight. With a call in to our attorney and the phone poised to be dialing our local news stations, I am not sure of what the next move for Maytag will be. Im sitting here after 21 days of not having a refrigerator hoping that a call and resolution comes soon. My family will NEVER EVER purchase a Maytag appliance again. I wouldnt even purchase Maytag brand toilet paper because Im sure that it would need to have one function and even that function as easy as it is would not work. People, please save yourself the headache and the money and the time of dealing with Maytag, Whirlpool, and Amana. Their customer service does not care about you, their products are crap, and they will swindle you and leave you high and dry. I hope to have some good news about this issue but I can guarantee that nothing good is going to come of this, well, at least for Maytag. Get on your social media and let people know how TERRIBLE this company is. STOP BUYING THEIR PRODUCTS. Sorry Maytag, the buck stops here.

For families where people work in gardens, work on vehicles and get just plain dirty doing things anywhere outdoors these agitator-less machines are not for you or me. Ive had mine for two years and I truly dislike it (Model MVWC425BW1). With different products I scrub dirt and grease stains on pants before they are put into the washer, scrub again when they come out of the wash and then scrub and wash again a few more times but I cannot get all the dirt out. I now work more on laundry and harder since I got this machine.This agitator-less machine is designed for people who dont get really dirty - just remove everyday perspiration and household grime. I think this machine was designed by engineers who have never done daily laundry for any length of time and theoretically thought it would clean really dirty clothes. They were really wrong! Having done laundry for 50 years, I now know that an agitator cleans better. It would be nice if other women and I, who have done laundry for years, could be on focus groups about developing new washing machines.

We currently have had our Maytag washing machine for approximately 15 years. The first thing we noticed was how user friendly it was. Also, the options that came with our washing machine met all of our needs. The second thing that we were excited about was how quiet it was. Our previous washing machine could be heard at the back of the house and was constantly out of balance. The third thing we noticed was how much cleaner our clothes were. Our clothes smelled better and had less wear thus saving us money. Speaking of which, the machine is an energy saver. One of the most significant attributes I can attest to is how reliable it is. There has never been an issue that required repair services. I am sure our Maytag will be in service for years to come. c

In the last 6 years my husband and I have bought the high end front load Maytag washers and both have crapped out within the year. I will never buy another product from this company again. Their customer service was no help and the washer needs to be rebuilt. We are waiting for parts which are back ordered months in advance. I will have no washing machine for at least 2 months. I do not trust any product made by Maytag and any company who sells Maytag should be ashamed to sell their product. There is nothing that I have experienced that would make me trust this company whatsoever!

My Maytag dishwasher will not come on and it is loaded. The control panel is out for the third time.

Both my washer and dryer are Maytag. Dryer element shorted out but was still under warranty so was fixed. Washer is very loud and now makes a rattling sound. Every so often it will hang in the middle of a cycle and the lid wont open until I unplug it.

MMV5207BAQ purchased in Feb 2009. I paid $512.00. 5-09 Bob Millers Appliance replaced the door because it bubbled. 10-11 Bob Miller appliance replace the door because the handle broke off. 3-12 Bob Miller appliance replace the door because the handle broke off. 10-16 Door handle broke off again under normal wear and tear. 12/14/16 I went to Bob Millers Appliances and was told to contact Whirlpool. 12/16/16 I called Whirlpool, Tina said, yes it is excessive but it is not under warranty and they do not make the microwave any longer and they cant do anything to repair it and they can not fix the issue. I find it how to believe Im the only person who has had this issue. I dont have kids. Its only me that uses it.

Maytag dishwasher, MDB4651AWW was purchased on 15/02/2010. Touch panel was replaced under warranty on 16/08/2010. Touch panel became defective on 04/07/2012. It was $103 for the service call: panel was not replaced (too costly, > $200). My 2-year old dishwasher is now useless. The touch panel on this model has failed twice in two years and is obviously a design failure. I would ask for a free replacement panel.

About 6 years ago we purchased a new french door style refrigerator. It lasted one year and one month then needed over $700 in repairs. First you need to know I am into electronics, DeVry graduate with 30+ years experience in repairing electronic devices. The Maytag basically frosted over in the freezer and was warm in the upper part of the fridge. I called a friend who had experience fixing fridges and lo and behold we found something really unusual.The way this machine operates is by blowing the cold air from the freezer up into the fridge. There is a fan located in the back of the freezer wall that does this. We found the fan, which was mounted in a grey box, spinning at about 2 revolutions a minute. My friend took me to the wholesale parts distributor he uses and we gave them the brand (Maytag) model (MFD2561HES) and they gave us a fan... just a fan with two wires. No grey box with fan inside... At this point I got curious, I mean WTF?!?The grey box was made not to be opened and I had to get clever so as to not damage whatever was inside it. After getting it open I discovered the fan inside was wired to a circuit board which upon inspection was a timing circuit. This is why the fan still turned only too slow to function. The new fan was installed and my only problem with the fridge now is the ice maker, which I disconnected.Conclusion: Maytag actually designed this fridge to break down and require hundreds of dollars of repairs AFTER the warranty expired by installing a timing circuit that disables the fan that drives the cool air to the upper part of the fridge to keep your food cold and your freezer frost free. Replace the grey box with a normal fan and youll get years of good use out of your French Door Maytag! As long as you clean the seals regularly and dont mind buying ice to fill the tray with... The repair cost me $39 and a six pack of beer for my friend.

I purchased a Maytag Bravos in October 2015 and a month and a half later the machine began to make a tweeting sound and the clothes were coming out incredibly wrinkled no matter what spin cycle I put it on. There were also times when the clothes came out totally dripping wet like they hadnt spun at all. I called Maytag and they sent out a technician from a local store which was not a Maytag store. When I told him what was going on, his response to the machine turning out very wrinkly clothes was, Well, why dont you just chose no spin. I said to him, So the clothes wont spin and I have to take out my clothes dripping wet? Doesnt that defeat the purpose of having a washing machine that spins? He didnt say anything to me.It turned out the machine needed a new gasket motor... after two and a half months... and it would take a week - minimum - before he would come back. Maytag sent me a survey which I filled out and they called a day later. They offered me a six month extended warranty for free. I explained to them that I didnt understand why something mechanical would break after two and a half months but the woman just kept apologizing.

Worst washing machine!!! I purchased the top loader Maytag Bravos washer HE in 2011 and they are the worst!!! It has been repaired three times already and now is making such a loud noise and I have been told it is the bearings. I did purchase the extended warranty and it expired. The reason I did not get a renewal is Maytag & Home Depot do not allow the the extended warranty company to let you know the warranty is ending. So now I have a 3 1/2 year old washer that needs bearings and will cost $500 + for repairs. Will not be spending anymore money on this absolute piece of junk. I had a Maytag that was 22 years old that I replaced and thought I was buying the same quality but never again another Maytag. This company may want to employ only repairmen because you will need only them because no one should buy a new one going forward.

Back in late 2017 we paid over $800 to purchase a front loader Maytag washing machine from Lowes. Before the year long warranty was up, the control board/motherboard stopped functioning. Maytag sent a repairman who tried to blame the problem on us even though he appeared well aware of the problems with Maytag/Whirlpool. After appealing to Lowes, they intervened and Maytag agreed to replace the washer with a higher model. (This process took many phone calls and a great deal of frustration).One year later, shortly after the warranty expired on the second washer, the control board again stopped functioning properly on the second Maytag washer. Since then, I have been rebooting the machine, starting the cycle over again numerous times and doing everything within my power to keep the washer going. The cost of replacing the control board is outrageous. Soon I will replace this machine with an LG with an extended service warranty. No more Maytag or Whirlpool products for me! They are once great American corporations that have fallen apart and are riddled with dishonesty and greed. I guess these corporations only mirror what is going on in this country and government.

I purchased my machine on June 2, 2021 and it was delivered and installed on June 4. I have successfully done two loads of laundry. On June 9, I attempted washing two small bath mats and 2 dish towels. When I returned to the laundry room to place the load in my dryer, I found the the items in soapy water. I tried many times to reset the load with no success. On June 10th I called Maytag’s customer service and spoke with an associate who walked me through a couple of common quick fixes. These also were unsuccessful. She referred me to warranty service. I will not be able to have my machine repaired until June 23rd! Obviously, if their repair department is so overwhelmed, the products they sell are a piece of junk. I am furious with both the product and the service I have received.

My Maytag Neptune washer was purchased last October 2010. In the past few months, the washer has been making a loud noise when spinning/washing. I had a Maytag repairman look at the washer, and all the barring, etc. needed to be replaced, which would have a cost of over $450.00! I am very upset with this outcome and just looked into it and found that this washer had recalls that the consumers were not properly notified about. The lack of recall communication is inexcusable, especially since I even went as far as to buy a 3-year extended warranty and still was not notified.What really set this situation was that the repairman suggested to not buy a Maytag washer and he added that it would not be a problem since Maytag has been purchased by Whirlpool and that the Neptune washer played a part of the ending of Maytag! This whole situation has really put a bad taste for any Maytag product, and all of my major appliances are Maytag as well as the dryer I just purchased a week ago, before I knew about all of the disappointment of Maytag. I am sure the response I will be getting will be as good as the notification of the recall, which will be nothing. Thanks!

I purchased this new Maytag washer (Model # MVWC300XW, Serial # 12621033) from Hahn Appliance Warehouse in Oklahoma City, OK 73107 on November 23, 2011. It is less than six months old, and the transmission has gone out. Hahn advised me that they had to go through Maytag Service, and they would only replace the part. I contacted Maytag/Whirlpool Service Corp. directly and spoke with a manager named David, who informed me he was sorry but would not authorize a refund or exchange for a better product because this was the first service call. I am very dissatisfied with this product and with the service standards that Whirlpool/Maytag offers on their products. If I were to sell a product that I knew has had numerous complaints, I would pull that product from my line offering and make either a full refund or replace with a higher level service product.

I give the Bravo T/L Washing machine and the Maytag company zero stars. I had to call for service 3 times within the last 22 months, twice for the electronic panel which needed to be changed, and the third time, it needing a new tub/drive shaft assembly at a cost of $405.27. I did receive a call from the Maytag customer service and all they would do is make a note of my complaint. I feel if you pay almost $1,000.00 for a machine it should work for more than 22 months. I believe Maytag manufactures an inferior product.Not only did it not last, my family and I found that the clothes didnt come out as clean as it should have, and sometimes, the towels would have a mildew smell to them after washing and drying. I assure you that I have read the enclosed instructions of how to use the machine, load the machine, and only used products designed for the machine

I bought my Maytag stand alone dishwasher model # MDC4650AWB in August of 2009. I have used it once or twice a week since then. About 2.5 years ago the control panel crapped out. I forked over the $$$ to have the part replaced and installed. Now, 2 years later the panel is once again slowly dying. I just got off the phone with the Maytag people and they refuse fix it and take responsibility for the product failure. The machine has worked adequately for me aside from the control panel issues. The control panel was built to break. Shame on Maytag! Lets go forward with the class action lawsuit!!!

Had our house built in 2009 and the builder carry Maytag Appliances. After 3 years every single appliances start giving us problems. First the refrigerator not getting cold, got it fixed. Then the dishwasher panel, then the built-in microwave, then washing machine. Just the other day the refrigerator broke down again and I was told the compressor was bad. Really? Whats going with this company? All the appliances from this maker dont have longevity. I have 20 year older refrigerator from GE and its still working. Please do not buy this garbage... Its a waste of your hard-earned money.

I purchased a Maytag Centennial Commercial Technology washer in September 2010 which is less than two years ago. It decides to stop spinning correctly in the Spin cycles. Clothes come out sopping wet so I contacted Maytag to have a tech come out. On the day that the tech came out from A&E Factory Service, he stated it was a switch. He changed the switch and still, it did not spin correctly. He then proceeds to state that it is another part, which again, it did not do the function correctly. He then proceeded to state that it is the clutch, then the transmission. The cost was raising to $519.00.I stated that I did not want to proceed because I would be purchasing a new washer with that quote. I stated to place all the original parts back onto the washer. He did so, but did not place them on correctly. The casing of the washer no longer is secured to the drum - bolts and plastic pieces are still on the side. He left my house with finger prints of grease on the walls. If this is the workmanship that Maytag recommends, then my business deserves to go elsewhere.A complaint was filed with the A&E Factory Service. However, no one has contacted me about the complaint as was requested. All I want is for my washer to be fixed or to have a tech who is knowledgeable to come out and fix it. I contacted Maytag to inform then of the situation and they stated that all their techs are certified. I do not believe that my washer of less than two years old could possibly have so many parts that are faulty. I hope that this may, in turn, help another consumer to avoid purchasing washers through Maytag and their parent company, Whirlpool.

Bought the pair of Maytags on sale at Lowes 6 years ago. They are commercial grade and wash everything. Have had no issues - works every time. It took a while to get used to not have an agitator but now it seems natural. Would buy again.

We bought our new Maytag top loading washer and matching dryer about 2 years ago. I am a busy woman so I havent had the time to write a review, but today being my day off, once again I find myself frustrated and disappointed with this set. The washing machine has a huge capacity, which was a huge selling point for me, however, if I put more than a small load in, the clothes come out still dirty, stinky and even have dry spots on them where they werent even in contact with the water. Even on deep fill it cleans the clothes inadequately, but at least they get wet. The dryer leaves the clothing rough and wrinkled unless I use the delicate setting, which I do for all cloths, and I use fabric softener liquid and a dryer sheet.I had a front load washer and dryer before, and my clothes came out clean and beautifully soft, but I replaced them because of the musty smell problem from the washer. I wish I would have kept them and figured it out. This set is the worst and I spent so much money on them. It takes so long to wash a load of laundry, and there is no way to interrupt a cycle without it draining and starting over completely. I have tons of laundry to do and I started 2 hours ago and the first load is still going. Geesh!!! Dont buy a Maytag. I paid for the extended warranty, but they are not broken. They have sucked from the very beginning.

Works great, quiet, cleans better than the others in my opinion, have had many others and they never impressed me like this brand does! I think this one gives you your money's worth and you don't have to look no further for a dishwasher again, and is top quality and hardly breaks down as well.

My first job was at Sears but went elsewhere to buy Maytag. I have had only 3 sets of washer/Dryer in 50 years. The set I have now are over 20 years old! I am looking at a Maytag refrigerator now.

Before putting clothes in dryer you have to untangle them. Sweaters and even t-shirts become stretched beyond help. Clothes smell like mildew if you leave them in the washer even just a couple of hours. Im 50 and had a few washer/dryers and these take the cake. Ive used the washing machine cleaner/refresher (something I have never done on washers in the past) and still a mildew smell. The dryer has lint on both sides of the lint screen. And as stated before if you dont untangle your clothes they come out in a big knot, partially un-dried & very wrinkled. The lint on both sides of the screen concern me - Ive never had a dryer do that before. Its not much lint on one side but enough to think something is not right.

Maytag Bravo washer and dryer delivered 2 days ago.My complaint is with the washer. I didnt know it was HE and that it requires special detergent! I didnt know the lid locks! I didnt know when I push the hot water button, the machine mixes in cold water! Complicated, delicate machine and not user-friendly. I dont expect the washer to last long.

French door refrigerator w/ freezer in bottom 2 years old. Purchased this model MFI2665XEM7 December 2012. June 2014 had repairs to freezer. Freezer froze up and bulb stopped working. Maytag covered repairs. September 2014 the ice maker stopped working and having it replaced as we speak. Total cost today for ice maker replacement $216.18. Am I POd, hell yes!!!!!!!!!!!!

Maytag MVWB835DW was less than 2 years old (purchased 1-14-16) when it began to fail. Maytag sent repairman out, he declared it beyond repair. Machine locks, washes and adds more and more minutes and cant turn it off without unplugging 5-10+ times... sometime takes a week to get clothes out of machine because of locking itself. I have extended warranty and yet when I try to contact Maytag, to have them honor this, there is eternal wait on phone, online, no help whatsoever. I read via Consumer Affairs that there are almost 3,000 reviews on this specific machine being a problem yet amazingly the Maytag man never responds! I have spent many many hours with no resolution. Amazon says so many reviews have been written about this, that they are unable to take my review because of excessive reviewing.

Maytag is no longer a brand well designed for longevity. Dishwasher, 3 years old. Wash sequence lights start acting up and cannot select the normal sequence. Called to schedule a service call. Maytag service person unaware of any issue. Was informed a service call will cost $99 minimum and provide 15 minutes of diagnostics, $29 for each subsequent 15 minutes. $299.00 max. (All CND $). Those rates added to new parts and it would not be cost effective to repair a $600 washer. If this washer gets replaced, it will not be with a Maytag.

Maytag Dishwashers work great. It cleans well and appearance is very good. I have always trusted Maytag appliances. Its quiet running and also energy saver. If I had to replace I would stay with Maytag.

I purchased our Maytag dishwasher last November. Last week, the control panel went out. I called customer service and they were actually polite and helpful, except for the fact that I had to wait an entire week to have a technician come to my house. Being that I live in the Balt/DC Metro area, I would have thought they would have enough people in the area to come over faster. Anyhow, we finally had the technician come today and tell us that the control panel needs replaced and that he highly recommends an extended warranty, which costs $200 for 5 years. He let my husband know that the repair itself would cost $500 if not covered by warranty!!! What a ripoff! I purchased this dishwasher because I grew up believing in the Maytag brand. Sounds like this is an extremely common issue and if Maytag wants to make things right, they should discontinue sale of their crap product and provide those of us who are stuck with it, a complimentary 5 year warranty. I shouldnt have to pay $200 in extended warranty to make up for the fact that my control panel is likely to go out again in another year, when Ill be forced to buy a new dishwasher.

Good deal, recommended by dealer friend. Front loaders, high efficiency, 12 years or so. Finally needs new bearings on the washer. Replaced electronic board 5 years ago. High repair costs would be the worst which is related to low-quality construction. I expect my next pair to last as long as the last 1. Full size, not stackable but oversized drums. Relatively low water usage, lots of different settings for different loads for washing and drying, automatic water level and wrinkle guard.

I owned a Maytag Bravos top loading washer for 8 years, and I loved it. It caught on fire while washing a load. Thank God I was home or it could have burned my house down. Just wanted to post this somewhere to issue a warning.

This dishwasher is at 10 years old, but is a real workhorse. This machine cleans like no other! Never worry about our dishes being clean. But we have replaced the seal once.

Our washer sounds like an airplane taking off. Called a repair man and the repairs are $690.00. The washer cost $999.00; such a waste of money. I called Maytag and they say there is nothing they can do. I will NEVER buy a Maytag again.

I purchased a matching set of Maytag Neptune washer and dryer about 6 years ago and the washer is junk! It sounds like a jet is landing in the laundry room. The repair man said it is not worth fixing - bad bearing. I am not happy!

Washer is noisy and water does not saturate clothes on normal wash. Have to use sheet setting for small or large load. Washer changes gears and it is so loud and clanks like something is falling apart.

I bought the dishwasher (Model MDB7749AWM) 15 months ago and paid $490.00. I had to put a new console in it ($245.00) on 07/16/2012. So that’s $735.00. Two days ago, the console went out again! I’m not putting $245 more in it! I called Maytag’s office. They more or less told me that was my problem! I am throwing that piece of junk away! And I’m buying a different brand. Maytag does not stand behind their product. Last Maytag I will buy! Warning! Do not buy Maytag!

I purchased the Maytag Bravos series washer and dryer recently. I love the dryer but the washer does not clean the clothes. I have to wash twice if I want it clean. It does not get the stains out and does not use enough water to rinse the clothes. It also does not use enough water to wash/clean the clothes. I ended up washing all the loads on bulky which fills the washer with water. It still doesnt agitate enough to get things clean. I am extremely disappointed in the Maytag product which I always thought was top of the line.

I spent extra money on a commercial grade Maytag dryer $1300 before taxes because it had a 10 year warranty. The motor and drum quit - and Maytag refuses to honour the warranty. I am appalled by their dishonesty and lack of integrity. I do not recommend them to anyone.

Last August I bought the Maytag Bravos XL. I have had 3 repairmen try to fix my problems with it and they cannot. The problem is, they cant fix an appliance that isnt designed correctly! Without water, one cannot wash. Dont be mislead that the huge area inside can be used for large objects like sheets and comforters. This machine is MUCH harder on my sheets and comforters than my old machine with a center agitator. I have shredded rugs, holes in sheets, black lines on clothes and a chlorine dispenser that puts spots on everything. The detergent dispenser hardware is rusted as well. Folks if this machine was an automobile, IT WOULD BE RECALLED!

I know that Maytag wants to conserve water by adding as little as possible... But when the damn machine puts hole in 5+ shirts Im not a happy homemaker!!! At first I thought it was the dryer so I had a repair come out and explain Im not the first person that complained of this issue. Its too late for me but Maytag needs to be aware that they are losing, what I thought to be, one of the top washers reputation.

On the first day, first time, the washer wrinkled clothes so bad I could not get them out. I talked to Home Depot people and they said I must lay clothes around tub like pictured in the book. I did that and they were still wrinkled. I called the repairman who said nothing was wrong with the washer. I talked to Home Depot; they did not have the answer. I called the repairman and he checked it out. He found nothing wrong. He did watch it washing and said he had never seen a washer tangle and twist clothes like this before, called Maytag. They said that I was loading clothes wrong, and nothing was wrong with the washer. They would not give me a number to call above them. This washer is bad. Maytag has known it for 4 years and done nothing about it. Ive been ripped off.

I have a similar story to Patricia. Been without a fridge for over a month. Refrigerator is almost brand new (bought last year) and a service-person has been out three times (going on 4) to fix it. The fixes NEVER work and then they have to order ANOTHER part and I have to wait for the part AND THEN the service person. I should not have to wait once the part comes in. People who have been waiting should be at the TOP of the list. Then again, this is Maytag...probably EVERYONE has been waiting for a fix.Ill never buy a Maytag appliance again unless they give me a new appliance, pay for the apartment sized refrigerator I was forced to buy while I waited--I have 3 children who need fresh food--and replace the $300 worth of groceries that went bad when I was assured the second fix would work (they wont replace my refrigerator--if they do, Ill be satisfied--unless it breaks in less than a year, too).

Our oven is 3 years old and the last time I used the self clean option caused the control panel to malfunction. Now we have to buy a new panel. The repair guy online advises people not to use the self clean as this is a common problem!!! What? I cant use that feature? That is so ridiculous!!! Now we have to pay $300. Whatever happened to the Maytag claim to quality and you would never see a Maytag repair man? Something needs to be done about the problem of appliances and electronics being so poorly made and basically disposable.

We purchased a Maytag dishwasher MBD7749AWM on 03/15/12 from Home Depot. The control panel went out on 01/24/12 under warranty. The unit was down approximately 2 weeks waiting for parts and a second service call. Just six months later (approximately 08/05/12), the control panel failed again. Thinking that a trusted American, iconic industry leader such as Maytag would stand behind their product, I called for what I thought would be a covered repair. I explained to a supervisor that their panels have not made it 1 year in service. She assured me there were no out of the ordinary problems with the panels for my model dishwasher in one breath, then stated they were out of parts and on backorder for three weeks. Now the truth comes out, further telling me that the unit is out of warranty and nothing can be done short of sending out a repairman, that I would be responsible for parts and service. After further discussion, she reluctantly agreed to send me the part for free if I arrange the installation and told me that it was very simple to install. When the part finally showed up on my doorstep with no paperwork, it was wrong. When I called and complained for waiting 3 weeks for the wrong part because there was no quality control in their parts and shipping department, all they could do was say sorry. They told me just to keep the part they sent and they would send the correct part. I begged that they ship the correct part overnight and they adamantly stated that was not an option. Maytag stipulates their process only allows ground shipping from FedEx per their contract. Knowing I had no other option, I agreed and waited for 5-day ground. The part showed up 13 days later and delivered by USPS. Apparently, I was lied to again and the left hand has no idea what the right hand is doing. Apparently, Maytag/Whirlpool have an inadequate and poorly trained quality control system in place and their manufacturing and electronic divisions are surly lacking a strong management team needed to go in and clean house. Instead, the whole mess they have contributed to continues to haunt Maytag has continued to be made to believe its okay to produce subpar products while continuing the complete demises of a once trusted American, iconic industry leader all while living on the Lorals of twenty years past.Whirlpool would do itself and this country a huge service by just letting this brand die and thrown on the heaps of scrap steel headed for China where maybe they can copy and fix what they were not capable of.

Purchased new Maytag Refrigerator from Mannys in Western MA. Top freezer, over $900.00. Never has worked correctly. We need to turn the freezer way up to freeze the ice cream and it forms frost all around the freezer with mini icicles hanging! But even worse... no matter what setting you put the refrigerator on it ruins your food by freezing everything. The only safe spot is in the deli drawer. I have thrown away hundreds of dollars worth of food that is destroyed because it froze in the refrigerator.A service man from Mannys came and ordered parts. He came back and said they were the wrong parts. Now he says that the refrigerator has a problem and Maytag is trying to come out with a plan on how to fix it. I talked with Maytag (took 44 minutes to get someone on the phone). The manager in service was rude, said they dont replace food and they would work on fixing it. 2 weeks later... no calls from either place. I called Mannys and they said they should have some news by next week. In the meantime I dont have a refrigerator that works! NEVER BUY A MAYTAG REFRIGERATOR!!! It is still under warranty and I asked for a new refrigerator... both Mannys and Maytag said no way.

Bought the matching washer dryer set thinking would be energy saving and reliable. Two months after warranty ended it quit, press pause/start button, no reaction. Started looking online and found out this is Maytags Frankenstein. Checked obvious stuff like power supply. Wont be buying another Maytag product EVER. Dryer still works but washer dead. Am retired, low income. Cant afford expensive repairs. Maytag ought to be eating this, not the consumer.

Have 2 fridges (one regular and the other is a side-by-side, both were bought in 2006 at Future Shop. The small one is not freezing and the side-by-side ($2,200) is busted too (compressor wont start....). How can Maytag say that their product are reliable on TV??? A Fridges compressor should last at least 15 years !! Maytag, you should at least have the decency to pay for the compressor!

Further down on this page is my complaint about the dishwasher. This complaint is about the company. This will demonstrate how cheap Maytag is. I filed a copy of my complaint below with the BBB, who in turn forwarded it to Maytag. They sent me a form with rules that they call Dishwasher Recall. Maytag will send me a $250 Prepaid MasterCard, providing that I: 1. Remove the old dishwasher myself. 2. Destroy the machine and/or render it inoperable. 3. Sign and date under PROOF OF DESTRUCTION AFFIRMATION that I have complied. Statement on the form (Your signature is your confirmation that you have complied). 4. Purchase a stainless steel machine (over $700). They list models you should buy. 5. Record on the form; Model Number, Serial Number, Purchase Price, Store where purchased, and Date purchased. 6. Send the signed Rebate Form back along with the sales slip. (Sales slip must show clearly Purchase Date, Purchase Price and Retailer Name). 7. Allow 6 to 8 weeks from the time the Rebate form is mailed. Are they kidding?! If I were to buy a machine at Home Depot, they will deliver, install and remove the old machine. I dont think I would take a Maytag dishwasher for free.

We have had this refrigerator since January 2011. All was OK for 18 months. Then the lid to the deli drawer fell off, the plastic bar that holds the two drawers up broke (weve had to use roof shingles to prop them up) and another one of the plastic pieces crumbled. Now the ice maker wont work and the refrigerator makes a loud ticking noise. There are only two older adults here and we have not treated this appliance roughly. After reading all the complaints on this site, Im wondering if any of it is worth fixing. My GE refrigerator worked for almost 20 years.

We have had our oven for seven years this past October 2015 and has now been down for three weeks. Last February 2015 (8 months ago) we had to replace the bake igniter because the oven would not get up to temperature. The most recent incident happened a few days after Thanksgiving (2015), I was cooking dinner and noticed that the oven was not reaching desired temperature. I then opened the door to see if it was hot inside the oven and when I did it must have ignited making a huge poof and flames came out at me! Thank God my 12-year-old daughter had walked away from cooking with me to answer the telephone because the flames came out exactly where she had been standing!!!I contacted Maytag and explained what had happened and how we could have had an explosion or someone couldve burned. The first questions they did ask me was if anyone was injured or any damage to our house?!?! I was happy for that however, it also told me that this has happened before! They called the Maytag repairman in my area and supposedly made it a priority call in which he could not come until 12/10 which was two weeks after this happened. Therefore, my husband and I contacted a different appliance man who came out and told us it was the temperature sensor. Since fixing it, the oven works ok and cooks properly however, when initially lighting/igniting it is extremely loud and makes a very large/huge poof! Its as if the oven is filling up with gas and eventually lighting! The other night when I lit it to show my husband it was so loud that it rattled the door and he immediately turned off the gas to it. I googled this and it said that its basically a mini explosion where the oven is filling with gas and then igniting! Its to the point that we could lose everything we have worked for just to make a meal! We spend over a thousand dollars on our beautiful stainless steel convect oven. Its gorgeous and when working works great however, Im petrified to use it now because Im scared to being burned or exploding! Now we start over and yesterday on Sunday I contacted the original Maytag repairman who said to call back Maytag again and hell come immediately. Maytag originally told me on the phone that they would cover labor and the service call however, ironically enough they did not write that in the dispatch order! Im outraged! What will it take before its safe for our family and home! My husband is ready to junk it and buy a GE however, we do not have the money especially before Christmas to do so. Oh and let me add that the first week we had the oven we had to call them for the window seal to be replaced because it was hanging. So now seven years after owning it and 10 months apart we are having major issues. What happens if its fixed and a year later it happens again? It could explode in our home!!! SCARED & IRATE WITH MAYTAG & WHIRLPOOL.

This is about my model MFI2569VEB2 refrigerator. It has French doors with bottom pull-out freezer, refrigerator door ice and filtered water dispenser. The delivery person installed the fridge and took off outside plastic and left inside plastic in. It froze everything until I took out the inside plastic. Within the first year, water started shooting out of the top of the fridge. A rubber connector for the icemaker, which was on top of the fridge, had broken. Within 18 months, it freezes everything in the refrigerator, even on the warmest setting. I have to leave it unplugged each night. The icemaker gets big chunks of ice stuck to it and wont let ice out. On top of all of that, the water from the fridge door pours out extremely slowly, this just how they are built.I will have to fix the thing myself and eat the expenses, so to speak. I bought the Maytag because Samsung had poor reviews. No matter how fancy you want your refrigerator to be, and how nice you want it to look in your kitchen, stick to the basics. The fewer bells and whistles, the more reliable.

Maytag #mbl2258es1 - started leaking in the freezer two years after I bought it. Two service men who did not know how to fix it. Now the refrigerator is not cooling. No more Maytags. Horrible refrigerator.

Purchased washer less than 2 years ago. Loud noise like a jet engine or helicopter in spin cycle. Did not purchase the extended warranty. Called Whirlpool/ Maytag customer service. Was told I could have one of their repair people come out. I would have to pay $300 which would give me the repair and extended 1 yr warranty, or I could get $300 off toward a purchase of a new washer. Are you kidding me? This washer wasnt even 2 yr old and making this horrid noise in the spin cycle. I had to have a independent repairman for Maytag washers come out to tell me it wash the bearing and would cost 3 to 4 hundred dollars to fix it. I said no thanks and after his $90 service call am stuck listening to this piece of junk make noise till it completely breaks. I will never buy a Whirlpool product again or recommend one. Whirlpool you sell nothing but junk.

We have reported the first time use of New Gas Range using the oven and range top at the same time is impossible because of BURN HAZARD AND the response was soft with no explanations. The range arrived March 26, 2015. We were impressed with first baking only. Family arrived at our vacation home for Easter celebration. Our first meal on Good Friday using both oven and range top was a disaster and the cook was burned on the stainless steel knobs. The oven vents below the knobs were about the temperature of the 380 degree setting of the oven!We rendered the unit unusable and called Maytag customer care department during the late table dinner. I explained on the 45 min call we were having this event and would be all leaving Thursday and their solution was 8 to 10 day shipping of Fake composite stainless looking knobs. These knobs will have to be sent to our Ohio home 500 miles west of the Range location?? If they could ship that day why not overnight??THE SOLUTION OF WEARING OVEN MITTS FOR STOVETOP COOKING IS NOTHING SHORT of silly to conduct meals for our guest. And other members of our family that we permit occasional use of the home open to burns using this Range until we drive 1000 miles round trip to drive the knobs back to NJ from Ohio??? Customer Care fails to listen. We will not be returning until May. To illustrate my concerns about the logistical issues I asked if Maytag would pay for the mileage and tolls for me to replace BURN proof knobs. Oh and will it work or melt? Furthermore who will pay for the takeout needed to feed our family? He did not get it and consulted with supervisors for most of the call therefore 45 min of wasted call. No solution, self installation on an $800 Range. Dissatisfied CUSTOMER with an unusable Gas Range Burn HAZARD!! Poor Design oven vents less than 2 inches below stove knobs! See Photos.

We bought a Maytag 2000 Series machine about 2 years ago. At first the machine worked great, as a new machine should. Then, after about 7 months water started pouring out of the top dispenser for detergent. I read the manual and looked online at the Maytag website for common problems. It said that sometimes small clothing gets sucked through the hose and needs to be unclogged. I followed the instructions to fix the problem. It worked fine for about 2 weeks later during the middle of a load the machine would stop and give me error codes. I looked these codes up and now I have another clog on the drain tube that needs to be fixed. Lo and behold these 2 problems have been continuing ever since. I cannot do a load of laundry without getting a code and having to take the machine apart. I called Maytag to explain my situation and the customer service representative said that because I fixed the problem myself at this point there is nothing that can be done. They do not guarantee that their equipment will work nor will they help solve the problem. I cannot believe that we spent so much money on something that I cant use. Not to mention the fact that when I do complete a load some of the clothes are ruined by the machine ripping holes in them. I would not recommend buying a Maytag because they dont care about customer satisfaction or the quality of machines they sell.

Our Maytag microwave MMV4205FZ-0 has the same ubiquitous problem as so many reviewers have mentioned. The microwave refuses to turn on (always at the most inopportune moments--like when the entire family is over for dinner. It doesnt matter how many times you open and close the door, it will often refuse to start. I think the worst part about this situation is that there are so many reviewers experiencing the exact same problem. Imagine how many havent posted a review. Doesnt it seem as though a rethinking of the door switch would have been in order long ago along with a recall? The fact that hasnt happened after so long and so many customers who are disappointed in their purchase is a sad commentary.

In July 2012 I purchased a Maytag BTM standard door refrigerator from Home Depot. Approx. 2 weeks from the 1 yr. Standard warranty July 2013, my refrigerator started cycling like every 20 minutes and loud popping noises started occurring. 1st service tech would only stay 15 minutes & did not want to stick around to hear the noise. Ran the standard tests and said everything was fine. That was around Aug. 2013. So I put up with it for a few more months and finally the popping noise was getting louder. 2nd service guy (Jan. 24, 2014) got to hear my video recording of the refrigerator cycling and loud popping noise. He replaced a bad dul part (Note: they all wanted to blame it on our ice maker that we never ever hooked up). Oops...wrong diagnosis. Whatever he replaced stopped the constant cycling pattern but now the popping noise is getting even louder like a shotgun going off. 3rd repair guy (Feb. 20, 2014) tells us that is normal and recycle product material is not that good nowadays?? I pay a $1000.00 for a noisy refrigerator and they say it is a normal sound. I dont think so. The refrigerator is now popping so hard that the right side of my refrigerator that faces the open is now buckling due to the compression of the heating and cooling which is causing the loud popping noise. If you rub your hand down the side of refrigerator you can feel the waves forming on the side of the refrigerator. Trying to get a Maytag rep out here. Something needs to be done about the production of these bad appliances.

Bought this Bravo washer from a Sears Outlet Store. Had trouble the first 2 weeks and did all the troubleshooting to no avail. Just when I was ready to return it to the store I decided to try one more thing. The guys who hooked it up had reversed the water hoses - cold was hooked up to the hot intake, and hot water was hooked up to the cold intake. Took all of 5 minutes to switch the hoses to the correct intake and the machine works like a charm. MAKE SURE THE WATER IS HOOKED UP CORRECTLY.

We purchased Bravos series Maytag washer and dryer. These are a match pair, the top loader, extra large capacity, very top of the line, $$$$$. The washer has already been replaced after many repairs, but the replacement new Maytag leaves a powdered gray residue on all the clothes because of the small amount of water it puts in the washer tub. Even on the deep water cycle, if I put in a blanket it will come out of the washer half dry where water has never reached it. This washer is the worst I have ever seen and cost top dollar. Maytag says nothing wrong but when I show them the powdered residue on the clothes they refuse to answer. This is the worst engineered washer ever, tangles the clothes terribly, does not clean the clothes and usually forces you to wash them twice to removed the soap residue left on them. I have tried every soap on the market, stacked clothing as Maytag suggested, tried various tricks Maytag has suggested, but nothing stops the grey soap residue. This washer cost almost a $1,000 for just the washer, it is a disaster. I have asked Maytag to refund my money but they refuse. If anyone else has their washer - we need to join in a class action lawsuit to force Whirlpool, maker of Maytag to replace this piece of garbage!!!

I purchased the Maytag Bravo model MGDB950YG on April 22, 2012. It worked great for a while then stopped heating and drying the clothes. After going through the Maytag procedure, a repair person assessed the problem, had to order the part then came back to repair it. But the same thing just happened again! Both Maytag and HHGregg need to go through the appropriate procedures, which leaves me without a dryer for who knows how long this time. Maytag will not do next day service probably because it costs them a little more. I think Maytag should have enough common sense to sometimes make exception to this. Today is Thursday and I cant get an appointment until Monday! I have owned two dryers prior to this which each lasted 10 years plus. I would be much more understanding if I had my appliance for more than 4 months (out of commission 2-3 weeks of the 4 months). Ive never been so disappointed in an appliance!

Absolutely the worst washer I’ve ever had! Do not buy this washer. Even after a double rinse there is white matter left all over everything! I’ve taken photographs of my laundry after two rinses and it’s disgusting. I will be quite happy to submit the photographs at any time.

Ive had my Maytag refrigerator for 19 years and it still performs well. I keep it clean both inside and underneath. The lighting is one aspect I really appreciate as there are two bulbs in the interior so theres never a problem seeing all the contents. Also appreciated are the movable shelves on the door and the ability to raise or lower the main shelves in the body of the fridge.

I like most others have experienced the same issues with the new Maytag top load WM. In addition my new machine dances across the floor like a drunk leprechaun. After Lowes told me that with my extended warranty Id have to miss work and pay 100 bucks for a service call I emailed Maytag. Needless to say they didnt even respond. Ive have learned a few valuable lessons. Dont assume that more money means better merchandise. Made in America doesnt say much. And please dont buy Maytag.

This Maytag refrigerator is very nice.. Sleek black with double doors and ice two ways and filtered water on the door which is very convenient. The filters are expensive but they last up to six months so that part isn’t too bad.

I bought a Maytag dishwasher on June 2008. This new Maytag dishwasher replaced an older Maytag dishwasher that caught fire and was recalled (I found this out after calling Maytag). The new dishwasher (Model: MDB 5601 AWB) also had a recalled part (heater coil) in February 2011. Two months ago, (the unit is now 3 years old), the control board started malfunctioning (certain cycles no longer work). I called Maytag today (Aug 24, 2011) but I was told by a Maytag representative that there was nothing that they could do. After reading so many complaints, I am ready to file a class action suit. It seems that this company continues to perpetrate fraud against an unsuspecting consumer for they knowingly continue to manufacture defective products.

Maytag fridge is a overpriced, ticking repair bomb. The fridge had issues with the compressor, control board (motherboard) and relay switch within a 12-month period. Customer service is weak in troubleshooting techniques and try to send the file over to a repairman. The repairman will show up at $80/hr + other fees and parts costing you approx $500, and still uncertainty that this fridge can breakdown at any time. Final advice: DONT BUY.

After 15 months of use the Maytag Dishwasher MDB8959SBS2 the control panel start malfunction. I read very carefully about the Home Depot Customer reports before purchasing this built in stainless steel dishwasher, and supposed to be one of the top notch on the market, around $850 retail price. It becomes a big disappointment. After three months of use, the top rack handle broken but it still under manufacture warranty, so we get it fixed by Maytag contractor. Then 15 months after regular use for a family of five, the control panel start malfunction, few bottoms will not start anymore. We are out of luck with one year manufacture warranty and working towards our VISA card extended warranty to try to get it fixed.

I am very dissatisfied with this Maytag Gemini oven Ive had it for 4yrs. It has been in the shop twice for the same problem. Temperature control. It is down again for the same thing temperature control. The repairman, who I had to look at it, says the bill will be over $500.00. I paid $1300.00 for this stove. I cant afford to put any more money in this stove. I had to pay $100.00 for repairman to tell me this. The model # met8665xw02 serial#D30522404. Is there a recall on this stove? There should be. I sold Maytag products for several years at Circuit City. I always pushed Maytag instead of another brand. I believed in Maytag. The repairman hasnt been lonely to me.

Consumers be aware! Anyone who’s considering purchasing a Maytag Appliance I would highly suggest reconsidering! I bought a $2000+ Maytag fridge Model # MFT2776FEZ00 in March of 2017 and have had numerous repair calls on it: Several for ice maker not make ice, ice freezing in the bucket into 1 big CHUNK, water running down front of door on the inside and outside, to not working at all and ice maker needing to be replaced. Several calls for fridge not properly cooling (temperature was set at 37 degrees F but the temperature in the fridge is 55 degrees F - per 2 thermometers), food is spoiling. The back inside of “Temp Controlled Pantry” is freezing everything and whole back wall behind the drawer is frozen with 1-2” of frost and ice. Defroster is not working and again parts being ordered to repair an obvious issue with this model.I contacted Maytag and their response was “sorry, we can document the problem.” They will do nothing more! These Appliance companies are ripping off the consumers! Everyone passes the buck! Repairman says, contact the Appliance store you purchased it from, Appliance store says, contact Maytag, Maytag says it’s the repair companys issue.

I got a Maytag Bravos 18 months ago and liked it at first. After using the washer for a while my towels were falling apart. Did not connect to the washer at first but I began to notice pulled threads on my towels. Talked to Maytag customer service who said they had never heard of the problem. She did say mix the towels with other clothes to prevent the problem. When I got this machine we had about two dozen good quality towels. Now I am down to maybe a half dozen. Those came from the six my Dad bought us for Christmas and I stashed away. The towels have pulled threads all over and will be completely destroyed soon.

I bought this dishwasher from Sears on Tuesday July 15, 2014. It was delivered on Friday July 18, 2014. On Friday July 25, 2014 two plastic clips that hold the top rack on broke, and one whole side of the top rack fell down. I called the 1-800 # in the book. Then I called the repairman they recommended. He came out on the Monday July 28, 2014. By the time he got here, the clip on the other side broke. Now the rack was hanging by one plastic clip. While waiting for these parts, the last clip broke and the rack was completely detached. So he received the parts on Friday Aug. 1, 2014. When he arrived, lo and behold, they sent the wrong parts. He had the side tracks that hold the rack, not the cheap plastic clips that attach it to the racks. So I have had my new dishwasher 14 days, and have been able to use it a total of 4 times before it failed. I am now awaiting the new parts. The parts that broke are made from a cheap thin plastic, and this is expected to hold up the entire top rack and the dishes its holding.

I have Maytag Model MGT8885XS03 Gas Range. I bought it in Nov 2013. The surface burner valves, which regulate the gas flow, are a bad design. One valve got stuck and needed replacement within first 13 month. Then another valve got stuck about a year ago and the third one got stuck today Nov 19. So far I spent $400.00, just for 2 of them and the last one has not being replaced yet. This is a safety issue, because it always happen when the stove is on and will not turn off. I need Maytag to replace my stove because I am afraid this will burn my house down. I bought Maytag because they always advertise as quality product, and now I have to live with the nightmare of burning my house down.

While washing clothes in my Maytag front load washer, I noticed that there was water leaking from the front left corner from the bottom. I have owned the washer for only 2 years, and Maytag manufacturer (Whirlpool) told me that it was going to initially cost $80.00 for a service call and then more money to fix the leak. WOW. Also the wood floors that are underneath the washer and dryer, is starting to warp from the leaking washer. I would recommend DO NOT BUY A MAYTAG APPLIANCE. The warranty is basically worthless along with the washer.

I purchased a Maytag Front-Loading Washing machine. It was purchased on 11/30/15. Approximately this January, 2017 the spin cycle stopped getting all the water out of the laundry. Towels came out wet, shirts came out wet and I tried washing a small bathroom rug that came out of the washer dripping with water. My husband called Maytag to tell them about this issue. They told him I didnt know how to load the washer machine. Wow, I have only been using washing machines for 45 years and now I dont know how to load a machine. Then they said they will send him a video to watch on how to load a washing machine. I watched it. I wasnt doing anything incorrectly. (Maybe someone should send them a video on how to build a proper washing machine.) I previously had a Maytag Neptune machine that lasted twenty years until there was a class action suit against the machine. The clothes came out fine from that machine. I just purchased an Electrolux front loader that works beautifully. Now I have a Maytag machine that is nothing but a piece of junk in my opinion. It cost $824.21. I will never buy a Maytag machine EVER. MHW7100DW.

I purchased this washer two years ago. It is supposed to be high efficiency so I was using cold water with the Water level sensor. The first load of dark clothes I washed came out with soap streaks all over them. This happened every time I washed dark clothes and sometimes they were barely wet. I emailed Maytag but they didn’t reply, so I called customer service and was told I should always use warm water and when washing dark clothes select a deep water wash. How is this HE?? When I wash towels or sheets everything comes out tangled and I am only putting in one set of queen size sheets. I will never buy another Maytag.

Had a brand new Maytag MDB4949 dishwasher installed on 10/20/15. Noticed an acrid smell of burning plastic coming from the pull handle. After going to the reviews I see a pattern of shorting control panel boards melting the ribbon cable. Having repaired Xerox copy machines for 17 years, I recognized the smell of an electronics short and melting plastic. There are 600+ complaints for the same thing. Going to call the store we purchased it from and will escalate from there.

I purchased a Maytag Centennial Top Load Washer in February 2012. I wish I had understood the workings of the washer before making the purchase. I am not at all happy that the lid locks as soon as the washer starts and unless I push a button to get the lid open. I cannot open the lid to maybe add more items or check to see if the water amount is sufficient or too much. I have no idea how much goes in for each water level. Of course, I cannot take water out but I could put more in if I see it is not enough. And after learning the water levels, I would know just how to determine the level I need. Some man must have designed the panel. Otherwise I am satisfied. I really like the large load capacity. I originally thought I wanted a front load to get a large capacity but this suits me fine.

On 12/09/12, I purchased a Maytag washer, model mvwc200xw, from our local Menards store. About 6 months ago, the washer started making a slight banging noise, and would occasionally move in the spin cycle. Now, when washing a small to medium size load, the banging noise is very loud and does a lot of moving. I found nothing in the troubleshooting guide to help me on this, so I looked on-line and found several websites discussing this same problem. They stated that the problem was a snubber assembly and the replacement part would cost $4.55. They also said the washer would have to be taken apart to change out this $4.55 part.I watched a you-tube video of someone changing this part and quickly came to the conclusion that I would need help in doing this. A comment was left in the video from a Maytag repairman saying that the person changing this part was not doing it in a safe manner. The repairman stated that changing it in the way this person described in the video was DANGEROUS! I wrote an email to Maytag customer service explaining the problem and asked if there was anything they could do to help me on this 1 1/2 year old washer. I received an immediate email stating they would get back to me in 3 days. Ten days later, I finally received a reply. I was told there was nothing they could or would do even though I was a valued customer and that they understand and appreciate my feelings of disappointment.I worked for a large department store from 1970 to 1990 and sold appliances, one of them being the Maytag brand. At that time, they were considered to be a top of the line brand. This was why I purchased Maytag appliances for over 40 years. I am surprised and saddened to see a lot of on-line complaints against Maytag appliances and also that this 1 1/2 year washer needs to be repaired so soon. Obviously, times have changed. I figured it would cost me at least $100.00 to have this washer repaired. Rather than do that, I am going to take this in need of repair to a scrape recycling center and then go out and buy a new washer, but it will not be Maytag! Maytag will never disappoint me again!

I bought a Maytag washer January 2016. We recently had a issue with it so I logged onto the Maytag website and found a service provider to come see what was wrong. I had to pay a $100 fee for them to come out and look at it. I was told that the transition went bad. The parts were under warranty however I would have to pay for labor, which would be $325. Called Maytag and was told because I did not purchase an extended warranty there was nothing they could do about the labor. I can buy a new washer for $500 why would I spend $325 to fix? Already lost a $100 for them to come out to tell me what was wrong. Completely not right. A washer should last more then 4 years! Do not buy any Maytag produces. Will not last!

I was pleasantly surprised that this basic model would work so great! It really gets the dishes clean. It came with the house so I did not choose it and probably would not have bought it if I had to shop for it.

Ive had my Maytag microwave (MMV4203DS00) for a little over two years. I started getting SE error code. The control touch pad membrane is shorted out. I suspect because the design doesnt allow it to be an over-the-range even though thats the kind of microwave it is! I think the humidity from the burners shorted out the membrane. I called the company and the part would cost approximately $180 for me to fix myself. I have a really hard time believing that one part of a $200 microwave costs $180. Ridiculous. It appears this microwave is designed to fail. Customer service was rude and snarky. The company doesnt appear to stand behind their product. Maytag used to mean something. I had started to replace all my kitchen appliances - microwave, then stove. I thought Id be consistent and buy Maytag based on their reputation. I will never buy Maytag again.

I have always loved Maytag but this top load washer is a bust. I purchased this higher dollar energy efficient washing machine to hopefully get the value out of it for years to come. Model MVWC565F. 4.2 Cu Ft. I use good quality liquid laundry detergent. I launder adult clothing (including business casual wear), sheets, towels and pet blankets. Occasionally the 20+ something children do their laundry while home. I often have dry spots on my clothes where they never got actually wet. I switched to only using the deep water cycle; however, this does not immerse the load in water. The smaller my load the less likely to get clean. Ive adapted to only have large loads but I still do not feel my clothes are getting clean. I often have to run the load a second time to not only remove ordinary day-of-wearing smells (very noticeable in socks for example) but to get them all wet and free of soapy/linty-like spots left on the clothes from the washer (most notable on black leggings, dress pants, etc). I always do my towels and bedding separate from daily clothing, so this is not coming from having a mixed load. I have also noticed that the load takes much longer (up to 2 hours) for my washing cycle. How is this energy efficient? It uses less water but more electricity? I miss my old fully-immerse-in-water washing machine that washed in under an hour! Love the dry that I bought with this but not the washing machine!! I do not recommend this washing machine!!

Maytag Bravos Quiet Series 300 - My machine is 3 yrs old and started making a very loud noise on the spin cycle. My last Maytag lasted 18 yrs and all my appliances have always been Maytag. I believe it now when Im told that Maytag does not make good quality washers anymore.

The way the side by side fridge/freezer is built contributed to several injuries. I am 60 tall and of normal size, and accessing anything in the side doors lower down always results in smashed head, near bleeding injuries. I am so sick and tired of it. No other fridge has done this to me. Add that to the shelves being near razor sharp. One of these days this fridge is going to land me in the hospital with a lawsuit. Most people are not 3 feet tall or 8 feet tall, thats the only way to use this fridge safely!

Had side-by-side refrigerator for over 12 months - Went completely dead - Would need $500 work!!!!! Just got less 6 months. Now need filter for water and air filter!!!!!! I wish I can give it less than one star!!!!

Bought refrigerator 2012 from Home Depot (model something like MBF1953YEB - how sad is it that I now have this number memorized?). Freezer too cold, refrigerator way too warm. Freezer air ducts frozen over. Tried manual defrosting twice per YouTube suggestions. Finally got repair for $400!!! Thats about half what I paid for it! One proponent repairman stopped me mid-sentence when I said Maytag saying, I know what it is. The computer (Jazz?) board needed to be replaced for $217. I just looked up Maytag to see it was bought in 2006 by Whirlpool. So I wont be purchasing any more Maytag or Whirlpool appliances.