Maytag #mbl2258es1 - started leaking in the freezer two years after I bought it. Two service men who did not know how to fix it. Now the refrigerator is not cooling. No more Maytags. Horrible refrigerator.

We purchased all new Maytag appliances when we built our house. So far, the stove/oven has quit working and been repaired 3 times; its always the ignitor. The dishwasher has been fixed twice. The washer no longer spins out as it should. The refrigerator and dryer so far have run okay. I am definitely going to change brands with my new appliances. I will not purchase Maytag again. Its not what it used to be. I will do without oven this time, until I can buy a new one. Also, the dishwasher door has had problems from day 1, and now, it will not close at all. It seems like its off the hinge. Definitely, its not the Maytag of years ago.

I purchased this washer three years ago. It worked fine, but all of a sudden the washer stopped spinning and was not following any of the cycles. Of course it was out of warranty. The repairman states the computer board on the washer is fried and will cost $400 to replace. Several stores have stopped selling Maytag because of quality issues. No more Maytag for me.

On March 2011, I purchased a Maytag dishwasher model #MDB7749AWB1. The dishwasher worked excellent for 16 months. One morning, with dishes loaded and ready to go, the start button would not light up. The other buttons did light up but that did me no good, I need the start button. A few days later, none of the buttons would light up. I found a repair person who said it would cost over $200.00 to make repairs. I refuse to put another penny with no guarantee that this new part would work. I will never ever buy another Maytag appliance. The last inexpensive, unknown manufacturers dishwasher lasted me 13 years. Do not waste your money on this thing.

I just purchased this Maytag Commercial Technology Washer and Dryer on August 31st, 2018 and We hooked it up today Sept 4th 2018. I put a small load of towels in this machine and it said it would take an hour and thirty seven minutes to wash. I added my detergent and pressed all of the necessary buttons and started the load. the machine started spinning and testing and adjusting. I waited to hear the water start to come into the washer but nothing. I then checked my water lines thinking they are not on but they were. Through the smokey glass on the washing machine, I could see water dripping as if it is hooked up to a slow drip IV Machine.I am taking this thing back ASAP!!! First thing in the morning on Sept 5th 2018 I do not need to call Maytag Customer Service because they know it is a piece of junk, so I do not need to waste a moment with this crap on my property. I see Maytag does not believe in a QUALITY ASSURANCE DEPARTMENT because that department would put a stamp of approval on this Junk for distribution.No Washing machine should take more than 30 minutes (40 mins max) to wash no clothes. I will have to invest in an old school scrub board and rocks, then I can understand an hour and thirty minutes worth of wash time. I have set the timer on my phone when I started this load and My towels have been in the washer for an hour so far and I can still hear the slow IV DRIP OF WATER going. I just checked the machine and the digital reading is saying it has an hour and thirty three minutes to go. there is no water in the tub of this washing machine. The towels are wet from the IV drip and the machine is now pretending to agitate the dirty towels but it is only going in one direction. It is truly a sad state of affairs, your hard earned money gets you nothing but junk and a runaround.

Updated on 08/13/2021: Today a repairman who is authorized by Maytag came out. He found the problem, some arm that popped out that is located underneath the washer. He put it back together and said he needs to order the part and it will take 30 more days. Set the washer so that it SHOULD work for a couple of loads. I spent $700 on a washing machine and I have to go to a laundry mat to get my clothes washed. Here is the clincher. The guy left no paperwork, nothing, not even a business card. So I am at the mercy of this repairman (I think he said his name was Jessie). The guy was friendly, quick and knowledgeable, however he told my husband he knew what the problem was going to be, if you knew why didnt you bring the part with you and he said the part is out of stock. Why, is this part unique to Maytag washers? So I am still waiting for my washer to be fixed.Original Review: In December 2020 I purchased a Maytag washer it was delivered in January 2021 and it worked great for the first several months. Then the machine started making noises, clicking noises like it couldnt move through the gears. Then I started noticing that my clothes were not getting cleaned. It was taking an hour to wash the clothes. I told my husband it is not agitating just clicking. We had to stop and start back up the washer just to get the water level high enough for the so called deep water wash. I was finding residue left on my clothes and had to wash them 2 or 3 times to get the clothes clean enough to wear. Sometimes it wont spin enough to empty the water in the tub. It smells almost like wire burning. It has barely been 6 months and I have to have a repairman out. I will review the washer again after it has been fixed or replaced. But as of right now I will never buy another Maytag again.

One year ago I bought a Maytag Micro-wave and a Maytag dishwasher - big mistake. I should have done some homework. I had problems with the dishwasher since the day it was installed. I should have suspected something was wrong when it was delivered. I opened my front door and there stood a deliveryman holding my dishwasher in his arms. He said, Where do you want it? I couldnt believe he could be carrying it by himself, especially since it took three of us to move out the old Thermador which by the way was still working just fine after almost 30 years. But my wife insisted on a new washer for her new kitchen. The Thermador was actually made of steel. The new Maytag was made of plastic even the motor. It had some steel and copper parts but mostly plastic. I dont think it weighed forty pounds. The problems began the first day with leaks through the door and under it. I suppose eight or nine service calls happened in the next 3 months. The factory service men were different each time and each had their own guess as to what caused the leaks. Over time they replaced all the parts that could be leaking some of them twice, because subsequent servicemen discovered that a previous service man had installed the wrong parts. We often had to wait several weeks because replacement parts were not on hand, and would be ordered and shipped directly to us. Then we would have to schedule another service call, only to find out the wrong parts came - more delays. One service man told us we were using the wrong detergent, even though it was the detergent and spot-free rinse that came with it. Another service man removed the door cover so he could watch to see where it was leaking when it operated. He said the soap was foaming too much and flooding over, so we had to try another brand of soap, even though by now we had accumulated three other brands that were just barely used. The service men never did fix the problem. It took much experimentation from my wife to stop the leaks, which meant we could only use a fraction of the recommended amount soap. By now we were using so little soap that the dishes always came out dirty. So our choice was mop up a wet floor or have dirty dishes every time. Most of the time now we wash the dishes in the sink. One service man said in Maytags effort to make the dishwashers more efficient, and less expensive to build that the motor and pump were way under powered, and everything was made from petro-chemical by-products (cheap plastic) and that we should invest in the extended warranty. Its cheaper than paying service calls when the warranty runs out soon. What we should have done was exchanged it for another brand. My wife said had she only known, we would have never replaced the old Thermador which will be my next dishwasher. As for the micro-wave there are many things I dislike about it especially the rectangle glass tray which is extremely awkward to remove and replace each time you have to clean out crumbs and spills which happen often. The timer on/off bell is way too quiet with no volume control. The message and operation display is difficult to understand. And to top it off the cheap plastic handle broke one week after the warranty ran out which I found out that its less expensive to buy a whole new door than pay for parts and a service call to repair handle. Maytags track record made me not want to deal with service dept. again. I will probably be money ahead to trash the two appliances, start over and do some homework and maybe buy a European made appliance. I know German technology is not all about profit making, but quality, reliability, durability. I hate to sound un-American but greed in American corporations will be their downfall.

I have a major complaint with the Maytag double oven design. With the smaller oven above, if you spill any liquid while taking something out of the top oven, the liquid drips down between the two panes of glass on the lower oven door. This makes it impossible to clean. Maytags reply - call a service rep and have him make a house call and take the door apart for you and clean it. Not warranty work so I would have to do this every few months. Also, when baking in the upper oven, cakes and cookies tend to overcook on the bottom as the dishes are so close to the element.

Maytag Bravos Quiet Series 300 washer/dryer - Purchased this set nearly 3 years ago from Lowes. The washing machine smells like toxic sewage. The Affresh brand cleaner no longer works. All of our towels and many of our clothing items have had to be replaced due to the stench. I surmise this is because it does not use enough water. The clothes get wrinkled badly, twisted, stretched out and torn. The dryer does not fully dry. Always had to run it again to get the items dry. Finally, it started making a horrible, loud, screeching and grinding sound. Neither the washer or dryer was quiet for long. Putting these out on my curb today for scrap metal pickup.

My Maytag dishwasher Model No. MDB7759AWS1 caught on fire last night, inside the control panel on the top of the door. This was very alarming as it filled the house with smoke and caused some fire damage on the bottom of the countertop also. This could have easily caused a house fire and is very disturbing. When I called Maytag, they say this model is not recalled. In my opinion it needs to be. This is a huge accident waiting to happen in other peoples homes. Please beware. If the countertop would have caught on fire entirely, the house would have gone up in flames.

Waste of $1700. Well all I can say is I wish I woulda read these reviews prior to buying but thought Maytag was a good brand. Boy was I wrong. Never again will I purchase Maytag products. I must say I haven’t had any issues with the dryer. Works great. The washer on the other hand is garbage!! It barely cleans the clothes. Some articles only get partially wet. Everything tangles together. The worst part is all my dark clothes ends up full of dust and lint. They look dirtier coming out than when they went in. Very disappointed. If you use deep load it takes about 1 1/2hrs to wash, definitely not energy efficient, and clothes still have lint on both cycles, and unfortunately most of our clothes need to be hung up, so dryer can’t pick up the lint. My old wash was way better. I shoulda went for same old style. Save you money and buy another brand.

I purchased a Maytag refrigerator (MBF2258XEB), stove (MER8674AB) and dishwasher (MDB7749SBB) on May 26, 2013. So far all three have been worked on. First, the dishwasher would not fill up with water after the trial run. Called the repairman out. A tag was placed in a position that was preventing the dishwasher from loading up with water. Granted, we should have taken the tag off, however, it stated not to. Lucky for me, I am still under warranty. Second, the refrigerator, which is a freezer at the bottom, started to leak. I thought that maybe we were dropping ice. However, I finally called and had the repairman back out. He knew exactly what the problem was because Maytag knew about it. There was a faulty plug. So in a matter of mins the problem was fixed. Lucky me still under warranty. Those two things happen within six months of purchasing these items. Now, the oven does not work. It heats up to the desire temperature but then cuts off. Called the repairman and he thought it might be the lower baking element. Unlucky for me, warranty has expired. So, $90.00 for service call. Received a called from the repairman, $120.00 for labor and $70.00 for the baking element. I purchased the baking element myself, $58.08 and installed it. Still does the same thing. Now I have another appointment for him to come back out and see what is wrong. Another $90.00! So far I have spent $238.08 on a $699.99 stove. I will never buy Maytag again. Depending on the amount to repair will depend on whether or not I go back to Sears and buy Kenmore. I had Kenmore for 10 years with no problems. I should have gone back to Sears for my upgrade. I did contact Maytag via email. I am still waiting for a reply. Live and learn!

We updated our kitchen appliances in 2013 and purchased all from Home Depot. Purchased Maytag Refrigerator, free standing range and microwave. What a big mistake!!! Not one of them are worth what we paid for them. I just noticed that I was getting a (chemical) smell from inside our 6 year old 3 door model MFI2670XEM5 refrigerator. Well being I know what refrigerant smells like I have a leak in the interior of unit. This is my final issue with Maytag and their so called great built appliances, I have had nothing but troubles since about 2 years after we purchased it.I guess what really surprises me is that unit is built by Whirlpool and has their name all over unit and I always had good luck in the past with the brand. This is one of several issues including rust on freezer door, broken plastic drawer frames to French door hinges broken, ice maker door issues. What a waste of my money that I spent on these and now after 6 years need to buy all new. IT WILL NOT BE Maytag or Whirlpool!!!

Hate my Maytag Centennial Commercial Technology washer. It takes well over an hour per load. Clothes come out very wrinkled, and my knits get holes very quickly. I would not recommend this machine to anyone. In fact, I warn people against it as I have been frustrated every single time Ive used it. Model # W10420382A.

I purchased both a Maytag Neptune washer and dryer in 2007. This is without a doubt one of the biggest mistake I have made. I have had the dryer drum and rollers replaced and the washer will no longer run. It is going to cost me hundreds of dollars to repair. To think I bought these units for 2 reasons: 1. that Maytag are the dependability people, but its not! and 2. Energy efficiency. It is not too efficient when they are broken more than they work. The worst was when the repairman told me that I had purchased the worst product on the market. These units are in short, garbage! I will never buy another Maytag Product!

I have on the Maytag dishwasher for about a year. Is very quiet, the dishes are not clean. I called three repair guys from Maytag. The first time they replace the pump. Second time the guy said he just had a designed machine is no good.

Bought the Maytag model MFI2670XEM and within 6 weeks freezer wasnt making ice. Repairman came and fixed it, within a couple weeks same problem again. It was fixed and within a couple months same problem. Fixed, but makes very little ice. Now 18 months later after purchase freezer is leaking water onto the floor. Very disappointed!!! After reading other Maytag reviews I am worried I will have to dump this relatively new refrigerator and buy another (wont be a Maytag) and our upgraded dishwasher from Maytag is terrible! I hand wash all my dishes before putting them into the dishwasher. The smallest bit of ketchup or sauce is not washed away in the wash cycle. Our Maytag stove/oven seems to not heat correctly, as well. Internal temperature gauge reads 5-15 degrees off all the time. Thumbs down Maytag! Extremely disappointed with Maytag products! Will never buy again!

My oven looks like it has never been cleaned. The self clean Aqualift does not work to clean your oven. If I would have known that this feature did not work for self cleaning I would never have purchased this oven. My old cheaper oven at least came clean on the self clean cycle. Now it seems I am going to have to scrub my self cleaning oven. What a waste of money. Will never purchase another Maytag appliance.

I have a bottom freezer Maytag refrigerator that is about 4 years old. It started leaking and continued to get worse fast... It appears that the gasket around the freezer drawer does not seal about half way up. It causes a sheet of ice inside the freezer, so I am not sure if it leaks due to the ice defrosting. The refrigerator doors do not seem as if they shut tight either. After reading many of these comments about Maytag refrigerators, I am not sure at this point if it might be better to buy a new one rather than fix this one??? I looked for a recall and do not see one. Clearly this is a defective appliance.

I purchased my Maytag side by side refrigerator 11/2011 and by 3/2012 the compressor went out flooding my pool house floor. Maytag replaced the entire fridge because I was only a few months old. I bought the 2 year extended warranty, went down to the pool house (which has central heat and air) and the compressor has gone out again! The results leaving my baseboards molded! My warranty went out 3/17/2015 and Maytag is helping NONE! The only thing they have to say is you can buy a new repair one warranty for $363 to repair for one year. I have had this refrigerator for 3.5 years and now this is the second time its gone out! Customer service said, pool house is different than a regular kitchen. I told her that the pool house is 1,000 sq heated/cooled kitchen, bathroom, sitting room. Thats no different than some houses. Why would that make a difference?? My parents have a 30 year old fridge on the back porch thats still running! I will NEVER purchase another MAYTAG product! Stainless side by side with ice maker.

Wish it was a French door style instead of freezer on top. Not good if you are tall. Other than that we are pleased with it but will look to trade for a French door style.

I bought my refrigerator in May of 2012. Brand new from Home Depot. It is less than 3 years old. Now it is not working. I did not purchase an extended warranty. I never thought in less than 3 years my fridge would stop working. I called Maytag, first question from them was about warranty. So I knew I was screwed. So, basically for $300 they would come out and fix the problem. I only paid $800 for the fridge. I am lost as to why in 3 years my fridge is broke?? Makes no sense to me. So I paid a tech $100 to tell me what was wrong with it. The evaporator is leaking. It is leaking. So the evaporator is bad and I cannot fix myself. So for another $300 they would fix, so a total of $400 in an $800 fridge.I am pissed. I remember my parents having a fridge for over 25 years. Why does Maytag not take responsibility for their problem. The products we buy should last longer than 3 years. It is just a way for them to get us to buy another product. So needless to say, I am one pissed off customer. So let the emailing and letter writing begin.

I just purchased this washer in Feb. 2012. The motor had gone out in Oct. I called Maytag Service, they came out to repair it. In Nov., it was doing the same thing again. I called Maytag Service, and they sent someone out to fix it. They expected me to take off from work where they inconvenience me with this washer. It is a reject washer. They would give me another washer and not consider people having to work and cant take off for their reject washer. They said as long as it is under warranty. I feel that I should be able to get me another. This washer has given me problems since I had it.

Bravos WL purchased in May 2015. Terrible product. Last week stained 2 shirts beyond repair. Maytag service repairmen stated these machines were poor quality and the only settings that somewhat work are Deep Wash and Bedding. They recommended I buy something other than Maytag. I am not making this up - it was unbelievable. I got Maytag on the phone while the service techs were here so they could hear the comments. The supervisor, Kimberly, said I could not get resolution unless the technician declared it a functional failure. I asked for the definition, as I would assume the basic function of a washing machine is to clean clothes. Still working the steps to resolution, but I believe there is evidence for a class action lawsuit.

Would give them 0 Stars if that was an option. Bought a Maytag washer and dryer in Aug 2021. Washer broke Jan 6 2022. Called Maytag/Whirlpool on Jan 6 as it was still under warranty. They only had one service company in our area to work on the washer. I called them and it took them 10 days to come see what is wrong. Ordered parts. Said it would be 2 weeks. We are now 6 weeks into this with no parts. Called customer service and they said they were notified that their service company needed a part and would take another 21 days to resolve. Talked to a supervisor (Demetrius) who sounded like he did NOT want to be in that position. Offered no solution other than we will just have to wait. Threw a 3 month extension for the warranty on which still does not fix the problem. Sad to see this company go down the tubes as it was once a pretty decent business with solid products. No longer.

I purchased a Maytag Dishwasher at $600. 6 months after installation, the control panel quit. Maytag sent a repairman and replaced the panel. 4 months later, the control panel quit again. The repair man told me that if it failed a third time, that Maytag would replace the dishwasher all together. The control panel quit again just a few days before the warranty expired. When the Maytag repairman came for the repair, he tried to convince me that it was not the control panel this time. He then replaced the control panel, but did not use the embedded electrical connectors. He literally cut the wires and wired it together by hand, wrapping everything in electrical tape. He said this was a different repair than the others and the three strikes and a full replacement rule didnt apply. I wasnt convinced and called Maytag to complain. I was promised a six month warranty extension, if I would accept the repairs. Two months later and the control panel has quit again. When I complained to Maytag, I was told that I had no six-month warranty extension and it had never been promised to me. They offered to send a repairman to diagnose the problem for $130. Needless to say, there will NEVER, and I repeat NEVER, be another Maytag appliance bought for my home.

I bought this machine about a yr ago. My clothes come out so dirty white spots all over my clothes. Now my bills are higher. Because I cannot afford another washing machine I have to bring them to the laundromat. I saved my money a long time to buy a washer and now I am without one and still paying for this piece of tin that does not work... If I ever get a chance to buy another one it will not be a Maytag. Trust me never never never again!!!!!!!!

Quiet, efficient and leave you with clean dishes & utensils at the end of its multicycle cycle. This unit can self-clean and is always beautiful with its shine finish stainless steel interior. This unit can be installed by any user as it comes with everything one will need to complete the installation.

So I read the reviews when I bought this Maytag Bravo Washer and figured stuff happens. We bought the top load Maytag Brava in 2013. We bought the Home Depot warranty, 2 years later the washer was leaking water. 5 repair visits and 3 attempts to fix the leak before it was repaired. As of 4-25-17 the wash machine displayed un-level errors and started vibrating with a thundering noise. Called out warranty repair and they stated we need new bearings. Repair is scheduled in 2 days and now the wash machine is thundering and spewing oil so it is shut off. 4 years old, and like the other complaints clothes come out with dry patches and not clean. This is a bad machine, we are saving for our next washer. It will have an old style spindle/agitator, no California efficiency and probably not Maytag.

I purchased my first and last Maytag double door bottom freezer in Aug 2018. The ice maker shoots ice out all over the floor, only half make it into the glass. It also sounds as though ice is falling down inside door. I had the ice maker replaced twice, the gasket as well, the back removed to check for water line blockage NO avail. Before the first ice maker replacement it sounded like a freight train. I questioned whether I had received a store second from Home Depot or a return as the stickers inside had been removed but HD couldn’t assist and Maytag didn’t care. Definitely NOT worth the 2000 I paid.

Refrigerator (Model Mff2558vems) purchased end of November 2011. Early in 2013 notice refrigerator first forming ice all over freezer, including an ice sheet on bottom of freezer. Then noticed water around refrigerator. Called maytag and they sent repairman even though a little over year and out of warranty. Their service people seemed to know exactly what was causing the leak as they came in with the correct replacement part. Worked fine however, there was damage to my newly refinished hardwood floors which Maytag did pay to repair. A couple of days ago I opened the freezer and again noticed ice all over freezer. The next day, water all around freezer. I cleaned everything up, so I thought. The day after, we noticed the hardwood in kitchen buckling up far from refrigerator and the laminate in dining room bubbling, even though there was no visible sign of water. Called Maytag repair company but they couldnt come out for a couple of days. Called another local repair service familiar with Maytag refrigerators and he couldnt find anything wrong with refrigerator even though he knows leaking caused by refrigerator. Called insurance co. and they sent over service master. Leak is definitely coming from refrigerator. They had to pull up hardwood floor, part of walls, the dining room. They now have five large fans going and a defroster to dry things up. This is upsetting, as my daughters wedding is next month, my husband is currently laid off and I dont need this kind of aggravation again. I love the french door idea, so roomy for my large family, but I am now afraid of this refrigerator. I dont want it but think it is ridiculous I have to shell out more money when the refrigerator is less than 3 years old. I talked with a higher level supervisor at Maytag and they are only willing to give a 100.00 rebate towards a new refrigerator since the refrigerator is out of warranty. This is ridiculous. I thought by buying American I was helping our economy but what I got in return is heartache and crappy merchandise. If there is a lawsuit in California against Maytag about these refrigerators I want to join. My friend in N. CA who bought her Maytag refrigerator the same time I did is also experiencing leaking. So frustrating.

I purchased a stainless steel (freezer bottom) Maytag refrigerator Model # MFI2670XEM0 in Oct 2012. Since then its been a nightmare. The repairman has been out four times, once being a week after I purchased it. It leaked and ruined my kitchen floor. Call Maytag, they didnt want to hear about it. As of this moment, I have three more things broken on the unit. My ice maker literally takes 3 days to make ice, the alarm on the door is broken, and the plastic crisper cracked and now will not stay in. Called Maytag again and they stated that they will not replace the item with one of equal value. They just keep repairing it. I will NEVER EVER buy another Maytag product again. I spent $1700 on this product and had faith in the Maytag product. That will never happen again. Shame on Maytag for not standing behind their products.

A refrigerator has to keep your food at constant temperature. The first Maytag refrigerator I purchased from Home Depot could not get cold. I mean the refrigerator never got below 65 degrees. I called Maytag and they played dumb. Just wait weeks for a repairman to check a brand new product that is not working. Home Depot replaced it in few days with another refrigerator of the same model. It runs but doesnt get really cold (it only has a fan in the freezer and the air comes down from the freezer to cool the refrigerator). I live with it because all you will get out of Maytag/Whirlpool is to turn the dial to a colder temp. A little over a year passes and the fan in the freezer just stops running. I called a local certified service person. He looks at the fan and says that its running but barely. I had to replace the motor at cost with labor of around 200 dollars. I kept the motor. Turns out the motor is made by Panasonic. The current replacement motor is made in Mexico. Now the refrigerator runs cold. Since I had two of these refrigerators that failed to get/stay cold, I think they got a bad batch of motors. Maytag response was to refuse to pay a dime, it is outside of the warranty - even though I had called about the refrigerator not getting real cold on the second refrigerator. So basically I lived with food being kept at a way too high of temp causing spoilage for a year and Maytag/Whirlpool could care less, they are only worried about their bottom line.That is not the only problem with their product. The drain pan grows a mold that looks like pudding. The only way to clean it is to pull the refrigerator out, take off the motor area cover (which is really cheap cardboard) and clean it out with a rag. There is no way to remove the pan. The compressor is mounted so low that it heats up the floor. I have concrete floors thus I have no fire risk but if you have wood floors, I would check the heat level. It is nearly impossible to clean the dust off the fins on the refrigerator coolant lines. The back of the freezer door shelves are metal and very sharp on the back. Thus if you stick your hand in to pick something up, you will get a nasty cut.I have owned only Maytag, Whirlpool and Amana products my entire life. I will never purchase their products again. They may pretend that you are buying an American product (they use the American flag) but this product is nothing but OEM garbage made by the lowest bidder. They try to sell you an extended warranty for around 300 bucks for an addition 3 years. I figured if the fridge went bad after 3 years, I would just buy a new one. I never expected a motor to fail less than a year (I would say it started going bad about 6 months into ownership as started making ice at a lower rate). Maytag refuses to stand behind their products. When I told them I had the motor that failed, they had no interest in even looking at it. Do not waste your money on their products. I also own a Maytag washer that is the worst washer I have ever owned.

We purchased a Maytag Bravos Automatic Washer 6/28/09. The interior enamel around the bleach dispenser started rusting about six months ago and it’s getting worse. Our white clothes are getting rust stains on them. Otherwise the machine works well, but what a huge flaw. We will buy a new machine, but not a Maytag.

Maytag dishwasher 5/3/2010 model MDB6709AWQ1. 12/20, 2015 it is dead, $69.00 service call. Failed user interface and main PCB parts estimate with labor $449.46. Called Maytag Co. We would pay the labor $139.00. MAYBE they pay the parts.

I bought a Maytag refrigerator, model MBF 2256 KEQ2, two and a half years ago. Now the cooling coils are freezing up. I checked heater and thermostat for continuity and they were okay so the only thing left was the timer control circuit. On the earlier models, the timer control circuit is controlled by a Timer Motor or an Adaptive Defrost Timer which is separate from the main Electronic Control Board and much less expensive. On later models (including mine), the timer control circuit is incorporated into the main Electronic Control Board so if your automatic defrost quits working, more than likely you will have to replace the main board. I did not purchase an extended warranty because I believe they are useless from past experience. I bought the part on Amazon.com, received it in four days and replaced it myself for a cost of $78. This part costs $110 to $118 at Sears or a Maytag dealer.

Bravos XL washing machine is the worst washer I have ever used. IT DOESNT GET THE CLOTHES CLEAN! There is not enough water when filling up, and you cant control it. I put a load of dog blankets in the washer and at the end, they were in the same order as I put them in; they hadnt moved! All the stains were still there and there was soap scum everywhere. Also, while I appreciate a large drum, it is so large that I cant even reach down to get the clothes on the bottom, I have to use a stick to get them up. I am so irritated that I spent $1636 for the washer and dryer (dryer works fine but same trouble with the huge drum). I got mine from Sears online after checking the Consumer Reports which put it in the top 5 washers!!! Dont buy this washer. Waste of money. Will probably just have to throw it out and its brand new.

Maytag Bravo Quiet Series 300 - I purchased the set 2.5 years ago and after 2 years, it started making a rubbing sound. I kept using it with having a family of 5 and this is why I purchased it in the first place; with 3 boys, I do a lot of laundry. It then quit working on me all together and wouldnt spin the clothes. I had a technician come out and it was the barriens that spun the drum so I had them fix it and it cost me $400. Then about a month later, it was flashing code F51 and not spinning. I had them come back out thinking it would be covered since it just got fixed but no, it cost me another $100. Now, 6 months later and here I am again unable to do laundry because its flashing F51 and wont drain or spin. I called Maytag and they tried selling me a warranty and said it wasnt recalled because there wasnt enough complaints. We need to all call and raise a ruckus. This is ridiculous. Sorry to hear everyone going through as I am.

I bought this over the range Maytag microwave model MMV4205DH-1 5 months ago and today a hairline crack appeared alongside the door handle. I called Maytag to find out how I can get this repaired since, as time progresses, it will become worse due to using the handle to open and close the microwave. I was told this was a cosmetic warranty which expired after 30 days. They would fix it only if the microwave couldnt be opened. Apparently, the handle can become loose but as long as the door opens, they wont do anything.I bought Maytag because of their supposed reputation. Im so glad this happened with my $300 microwave as we were getting ready to replace our washer and dryer and were looking at Maytags. Good to know they dont back their products before I spend several thousand dollars on a washer and dryer. I will NEVER purchase another Maytag. My $120 generic microwave lasted 10 years and I gave it to my son and it is still going strong.

Maytag Gemini - This is a double oven which I purchased in 2010. 2 days ago Apr 13, 2015, the outside glass in the bottom oven simply exploded. The oven was in use at the time. It blew the side brackets off and glass was spread into my dining room as well as a mess in the kitchen. Maytag was supposed to send repairman today. Have waited all day and finally called repair company. They knew nothing of the repair and supposedly will contact Maytag and call me tomorrow. We will see. In the meantime has anyone else had this problem?

Bought a new maytag gas range march 2013 model #mgr8674ab. The oven would not light at all. Would just click. Still under warranty. Called the service. They came and had to replace the controls in back. 2 months later the same thing, only this time it comes on and goes right back off. Then a week ago got it to light, used the oven and tried to turn it off and it would go off but immediately light up again. Scary to say the least. Another call to service. They are coming tomorrow. This is November 12 2013. I would not buy another maytag gas stove. There is something terribly wrong with this model.

I have had this washer for a few years now and it is the WORST machine ever. It never gets clothes fully clean as air gets trapped in some items so they stick out above the water. The drum only fills about 1/4 of the way no matter what you are washing. It is always unleveling and you have to constantly re-arrange bed sheets and larger items. I have to first soak larger items before the wash cycle. Nice HE machine. When I purchased this machine the sales person said you can wash 10 bath towels. I read the directions which said make small piles of clothes and I called and told her that after I had purchased the machine. Her reply was oh, I didnt know that. Obviously. This top loader without the agitator cleans great if you only throw in about 10 thong underwear at a time or two pair of jeans.

I purchased a product less than one year ago. The clothes are getting snagged in seam on interior of the front panel. I went back to the store and felt the same gap in the seam on the panel on a floor model, so I know it is not just my machine. I called Maytag service and a representative acknowledged the problem but also said that if there is no fix for it, I would be charged for a service call even if no part was replaced- quite a contradictory statement. She said she doubles as the Complaint Department. If this is a manufacturing defect, it should be replaced. The front panel should be recalled.

There was a maytag dishwasher in the house we bought 11 yrs ago. The only problem we have had is a recall on the rinse aid dispenser which was replaced by a service man but never worked again. We are completely satisfied with the operation of the unit, our only disappointment is the wire racks. The original racks plastic coating broke at the end nubs and became rusty and swollen. We found someone selling a unit and we just took the racks and left the unit for him to resell rackless. Unfortunately not two yrs later the same thing has happened to those racks. Even tried these little plastic covers that are made specifically for this problem. They were virtually impossible to get on and didn’t last more than a few months.

I purchased a Maytag Centennial MVWC360AW washing machine on July 11, 2013 at The Home Depot. I assumed that I was getting a good product based on my Moms old Maytag washer. This machine is the farthest thing from quality that I have ever experienced. My Mom would roll over in her grave if she knew how CHEAP Whirlpool has built---what is supposed to be a---Maytag! The machine worked fairly well, at first. Even though I didnt like the low water arrangement. I like clothes to be fully immersed in water! That went on for 2 years and 5 months, until NOW the led light goes to Rinse, but it wont agitate. Then the led light goes toSpin, but it wont spin! I called a local appliance repairman and he told me that the control is bad. They cost about $250.00. Its not worth repairing!! So, Im stuck with this piece of junk! Shame on Maytag/Whirlpool for building a PIECE OF JUNK!

Christmas sale, needed a washer. Had a great experience with Whirlpool Duet so went for the on Sale Maytag Bravo MCT. No agitator which I thought odd. Bought the warranty. Did no good as soon as I hauled the washer home (3-hr trip one way). It wasnt washing my clothes clean. Hubby said try different cycles and soap and temperatures but at 8 months pregnant it wasnt long when I didnt fight with the machine but focused on a very busy life. Baby number 7 and I didnt care how the clothes washed as long as they didnt stink. Well baby is older, the warranty is not over and after much dialoging, no one will do anything for me. I put muddy pants in, they come out muddy. I put cloth diapers in, they come out smelling like pee. How hard can it be to come up with a machine that just turns clothes round and round with a little soap and water? Apparently really hard as Maytag failed to test this machine. Maybe city folk just have lightly soiled but on the farm with 7 kids, my kids play hard and their clothes are very dirty. They continue to stay dirty unless I wash them twice on Power Wash and Extra Heavy Load. Not impressed. Would like a replacement washer of equal or lesser value, anything that works. Oh P.S. I have the receipts and order number. Sorry its not put online to be verified buyer but dont feel like digging for paperwork at the moment.

I wish I had read the reviews before selecting this Bravos XL washing machine. I bought these from Conns Appliance as they were on sale 750. Rounded figure... They were delivered today and the company was professional and set them up, I have spent the last 4 hours washing the same medium load of childrens clothes trying to get them clean. Ive even separated them into smaller loads and am now into the 5th hour of laundering this same load... Im returning them but its gonna cost me 15% restocking fee. If theres a class action please count me in. I thought because our Maytag Neptune lasted so long wed have a great outcome again with these, boy were we WRONG!

If I could rate it lower than 1 star, I would. We bought ours new in 2005. Within 6 months, the main pulley for spinning the drum fell off not once but thrice. The repair tech said that the shaft was machined incorrectly at the factory and the bolt that would normally hold it on was backing out. The 3rd time it happened was close to the end of the warranty and the tech could not make it out before the warranty date. When he did show up, they wanted to charge us. I wound up putting the part in myself. Two months later, the suds alarm came on, which caused the water valve to open. The pump kicked out and the water valve stayed on flooding my basement and the electronics in the washer. This happened twice. The second time was a week ago and I tossed the ** out to the curb. We also have a Maytag Gemini double stove which does not work either. This is the second and last Maytag appliance that I will ever own. They are junk!

I am submitting this review today to express my disappointment with my Maytag washer. This is the Maytag MVWX655DW (Bravo), with Serial# C61842055. In August of 2016 I lost many treasured items due to a flood in Lafayette, Louisiana. My daughter and I were devastated and displaced because of this event. This is also in addition to completing Cancer treatment 2 days before the flood.I lost my GE washer which was a great product. It was a struggle for a long time, but we were finally get back on our feet. I was able to get another place to live, and it was time to purchase a washer. I was told that Maytag was one of the best products on the market, so I decided to purchase my first Maytag washer. This did not turn out well for me, and it was very disappointing. After 9 months of ownership of this product, it is broken! It is my belief that the product may have been defective.I put in a service call, and had a repairman come to my apartment on June 19th. I was told that my washer needs several parts to repair it, including a pump. I have never had this issue with prior washers. My previous washer before my GE purchase survived for over 10 years before it has had any issues. I called on June 26th to ask about Maytag issuing me a new washer or a full refund, instead of repairing this faulty product. I was told no, and was offered and extended warranty for 6 more months and $75.00. I expressed to her that I would rather have a new washer.The Bravo Washer is a very bad product. Instead of taking advantage of customers, Maytag needs to stand by that 10 year warranty sticker on the washer. Please understand this purchase is a LEMON. This washer did not last a year. After all I have been through, I did not need this financial hardship. In the long run, this product will die again. Unfortunately for me I may not be able to afford to purchase another washer. I am still getting follow-up treatment for my Cancer, and it is very expensive. Can someone please re-evaluate the need for a replacement washer or offer me a full refund? This product should not be broken after only 9 months of service.

I am renting to own a Maytag refrigerator and it is leaking water on my floor. Runt my floor already - had to replace the floor once. Sent it back to the place where I got it for them to fix it. Paying insurance by the way that isnt worth a crap either cause they wanting to tell me that I left it open at some point or the lights was off at some point. Anyway to make a long story short they gave me the run around and didnt want to fix it. But how do you fight big companies? This was a rental company by the way rent to own so now I have 4 payments left out of 24 at 180.00 each and they still dont want to fix it. I dont know who to be madder at - the rental company or Maytag from selling this piece of junk. But by me renting to own it if any problems occurred they were suppose to fix it. Youre already paying twice the amount to get one cause of credit issues. But thats no reason to double screw someone or should I say triple cause you getting doubled the rental company alone. They need to recall this refrigerator. It has been a lot of complaint and they want to tell you to go behind the refrigerator unstop a line. Well I didnt buy this refrigerator to have to work on pulling it out from the wall every two days to do this procedure. This is crazy. Any one out there looking to buy a refrigerator my advice to you would be do your research and stay away from rental places whatever you do because you will pay twice the amount and they wont stand behind their promise either to fix it as long as you renting from them! And stay away from Maytag!!!

I have owned this washer for 3 years and purchased it to match the Centennial Dryer and because of its advertised commercial grade components. The washer has just now turned 3 years old and has never been abused but I have been told the drum bearings are going out.

Leaked and leaked, spent hundreds on never ending problems from day one. No support from Maytag. I was told by Sears salesman it was the best you could buy. Our old washer lasted 30 years. This one never worked right - dead at 5 years. Shame on Maytag.

I purchased a Maytag Bravos 5 months ago. I had trouble at first with unbalanced loads. The repair man came to look at it twice. One thing that can unbalance your loads is if small pieces of laundry such as a sock gets outside the basket. Sometimes the basket has to be taken all the way out because small pieces can be lodged under the basket. This happens when you fill the machine too full and those small pieces float to the top.The suspension on my machine ended up needing to be replaced. I have read lots of reviews about soap rings in the clothes. That happens from using too much soap. Make sure you are using HE detergent for one. I cut way back on my soap and my laundry gets clean and no problems with residual soap on my clothes. I was very unhappy with my machine at first but now I absolutely love it!

I purchased both a Maytag washer and dryer and I am very disappointed in both products. Both appliances have electronic controls and are substandard. For the dryer if you do not touch the start area exactly right it will not start, can take multiple tries. For the washer, my town turned off my water to switch out the meter, once done the washer did not know how to clear the air in the lines and gave a LF error and no one at Maytag customer service could help me solve the issue and then could not set up a service call as their computers were down and did not have a process to call back the customer. This is terrible Customer Service - never again Maytag or any of their other products????

Spent a lot of money on a Samsung washer. Will never buy that brand again. Too much money for only working for 2 years. And left clothes dirty. Had to wash clothes twice. My Maytag washer was bought with a deep water wash cycle. Totally love it. Also not a front loader.

Im living in a shop lot area and its near a university school. It has different laundromat stores here, and the cheapest is the one who have Maytag washers. So Ive been going there to wash clothes and as time passes, I noticed that the clothes have been getting stains after washing and these stains cannot be removed easily. Ive read reviews about clothes getting stained using Maytag washers and I cant believe that it happened to me. I dont know whats with Maytag that makes the clothes dirty/stained. I went to other laundromat stores that are not using Maytag washers. Its quite expensive, but it really makes your clothes clean.

Like everyone else got that French door fridge and was also duped on that 1 yr warranty - a 95 dollar repair visit for a 485 repair job on a 1200 dollar purchase. Shame on them. Im gonna fix my new floor and replace that frozen bottom, leaking on the left, non-working ice maker 2 yr old refrigerator. Very disappointed with the whole thing and sorry for all of our losses.

We purchased a new Maytag Bravos washer and dryer. The washing machine senses the weight of the clothing and determines how much water to use. The machine does not put enough water in to completely immerse the clothes, therefore after the load has washed, the clothes come out of the washing machine partially dry. I have to wash the clothes a second time therefore using detergent twice, water twice, electricity twice and my time twice to wash each load. After a while the machine stopped washing altogether. I would load the laundry, add the soap, close the machine and start the machine. It would begin to put water on the clothes and sense the weight of the clothing and it would get stuck there. I would hear a buzzing sound and the clothes have been stuck on this same cycle for over 15 minutes and it would not wash the clothes. I tried starting the machine again, and it would drain the machine. Id have to add more soap, use more water, use more electricity and use my time again to try and wash the same load. They sent out a repair company who looked at the machine, did whatever they did (and left a bunch of water on the floor behind the dryer and didnt have the decency to tell me so that I could clean it up). They said they had to order parts and they would come back. They called me several hours later and said they had the parts in their warehouse and they could repair the machine.After a while, they said they were finished and that the machine was repaired. I tried to wash a load after they left and... the original issues were still there. I called the repair company and told them what happened. I typically do laundry once a week, so out of fairness to the technicians, I told the lady that I didnt have any more dirty laundry and that I wanted to try the machine again when I had dirty laundry the next week. I called the next week and Maytag said that I had to pay for the technicians to come out, even though they never repaired the washing machine.After complaints they offered me a $75 credit towards the repair company which I refused to accept. Then they told me I could buy another Maytag machine and they would give me a discount. So basically, I would get something like $76 off of a $600 machine. Really? And then the idiot had the nerve to tell me that it was customary for the clothes to come out partially dry. So in other words, he was telling me that these machines were designed with flaws to partially wash clothes so that consumers would have dirty clothes. I asked for a replacement machine of equal value and they told me that Maytag does NOT replace machines. They sell this crap, knowing that it is no good and they arent willing to replace it! I got someone else on the phone and he said that I will not have to pay for the technicians coming out a second time to attempt to fix the machine. I AM NOT A HAPPY CAMPER.

I have a Maytag dishwasher and the rollers for the racks are failing due to heat: plastic wheels breaking up. $35 each to buy and replace. There are eight total. So $280 because of poor testing and quality of materials. Manufacturers should test to ensure the parts last a reasonable period of time and are designed for the environment in which they are being used.

I purchased a Maytag refrigerator (MBR2258XES4) from Home Depot in 2012. I bought a five year extended warranty. It started leaking at the bottom. Repairmen said defrost drain clogged not covered! Cost: $180. DO NOT BUY MAYTAG, N.E.W. (Asurion Co.) warranties or Home Depot appliances! This is text book deceptive advertising. At no time did Home Depot associates in Kitchen and Bath departments say that this common design flaw existed and that it was not covered under the N.E.W. Asurion warranty which cost me an an additional $150.00! I am interested in joining a class action lawsuit against Home Depot and Asurion Co (N.E.W.) warranties.

I bought a every expensive Maytag Neptune (washer and dryer one unit) and it is now sitting in the carport. The washer broke and I had to have service people come to my house continuously. Over a period of 6 months I had to pay for 3 motor control boards plus service calls. Thats when I had I moved to the carport. In 2012 I bought a Whirlpool Duet washer and dryer so I would be able to stack them. I had to put them at Sears because I had to use layaway. I paid for them over 12 weeks and had to use a laundromat during that time. Last week I got a F01 E02 error code which means replace motor control board. These boards cost over $300 each not counting the cost to install it.I did talk to Sears since the washer was only bought 4 years ago. They were nice to me but could do anything for me. Truly sad when a washer only lasts 4 years for the amount of money I had to pay to purchase it. I dont know what I going to do now since I am now retired but I WILL NEVER BUY A WHIRLPOOL OR MAYTAG AGAIN.

We purchased a Maytag washing machine top load (#MVWX550XW) on 12-20-2010. The switch on the machine that starts it running when you close the cover went out under warranty. They put a new switch in and it only lasted a while. I had to pay this time, $240.00 for repair. Now again, 1-2-2013, the switch is not working. I think that it is a lemon. I called the company and they will not cover the cost. Instead they want to sell a warranty for over $300.00 for one year and then if I purchased it, then they would fix it.If I did that, I would have more money into the repairs then what the machine cost ($583.44). Isnt there a lemon law? It looks like I will have to get rid of this machine and buy a different brand. Yes, Maytag has let me down. I cannot recommend their products because of the quality and answers that they give. I cannot afford an attorney, which leaves me upset when somebody wont cover the cost of the third repair.

I purchased a Maytag refrigerator from a local business (Decker and Sons in Grand Rapids, Michigan). The fridge is a French door style with the freezer on the bottom and a water dispenser/ice maker in the left door. In the 19 months weve owned the unit weve had to have service three times. One time for the freezer door not shutting correctly, and two times because the refrigerator portion quit cooling (freezer was fine). Both times it was due to something breaking that defrosts the area behind the vegetable drawers.Both times all of our food went bad. Second time it took almost two weeks to fix (Diamond was the repair service). Now, after the service, the left door doesnt shut correctly. The quality of the unit is so questionable that I hesitate to fill it back up with food. Its just plain old junk. Luckily, we purchased a five year warranty when we purchased it...but we thought the service would be performed by the shop where we bought it, but its farmed out to other repair providers.

Bravos washer, a year old machine, needs new main electronics board $220.00 plus $125.00 labor to install. Repair guy said humidity makes them go out. Go figure a part sensitive to dampness on a wash machine. Why don’t they seal it better? By the way, this machine does not wash, worth a crap. I am getting something new.

Maytag dishwasher MDB7749SBM2 - I purchased this unit from Home Depot. It worked fine when working. In less than two years the control panel had issues. Would not let you start cycle, would randomly start on its own, would light up randomly, would only let one cycle work, would not work at all, etc. I received no help from Maytag. After open up the door panel the problem is obvious. The ribbon cable from touch (control) panel to control board had black spots from corrosion. Poorly insulated or poor design. $150 for part and another $100+ for repairman. As Ive seen from several of these posts it appears to be a common problem now to Maytag, which they choose to ignore in spite of class action lawsuits. Obviously last Maytag product Ill ever buy.

We purchased our Maytag Neptune Washer and Dryer approximately 5 years ago. Over the past year or so, Ive noticed an odor coming from our washer and it’s becoming stronger. Water is staying in the drum and there is mold growing on the rubber seal when you open the door.

MAYTAG REFRIGERATOR SAFETY ISSUE SHARP EDGE Maytag refrigerator model MRT118FFZ01 purchased Feb.2018. There is a safety issue, sharp edges. Maytag has been aware of this for over 1yr from customer reviews. I went to consumer affairs.com and there are numerous complaints on products/customer service. I have been asking for a replacement door since Feb. On Sept. 7th I cut the palm of my hand on sharp edge, drew blood, no stitches but I was very upset. Called Maytag, transferred to the safety dept. sent out service tech. He reported that it was a safety issue, very sharp edge, he had to put duct tape on corner to prevent any more injuries! He requested that new doors(freezer&refrigerator door) only be sent, I do not want/need the whole unit replaced. Freezer door has sharp edge also. I have numerous emails to/from corporate office begging since Feb. for a new doors so that this would not happen! Maytags solution is to buy back refrigerator or I should pick another model. Neither is a solution for me. I picked this model for a reason. I asked them to provide me with the simplest solution which is to contact factory where it is made, red flag it, talk to manager, quality control check to see that there are no sharp edges before it is shipped to me. They refuse to do that 1 simple common courtesy, customer service request! They cannot guarantee that door will come without a sharp edge! My model is not the only 1 with this problem. I talked to salesman & model in store has sharp edge & in the reviews the same model had sharp edge which was submitted over 1yr ago! So Maytag has been aware of this safety issue for some time now but chooses to do nothing about it! I chose Whirlpool because of the name, I thought it stood for quality & above all excellent customer service. Was I wrong, found that out thru numerous phone/email conversations. They just dont care! Is it too much to ask Maytag to give me a refrigerator with no safety issues?!!! I have talked to Aaron in the corporate office, he was no help at all. His # 866-817-5404 ext **. I have all the emails to/from him. Please help, I want this same refrigerator, only model that would work for me. Now that I have had personal injury & have spent so much time/effort, aggravation since Feb. trying to have them do the right thing I feel that I am due monetary compensation. Bottom line this complaint is concerning a safety issue & horrible customer service from the call center to corporate offices! The Maytag name isnt what it used to be known for, quality & service.

We purchased a home one year ago. It has all Maytag appliances that were anywhere from one year old to two years old. The Neptune LE washer is not working as of today. This washer is supposed to be the top of the line, and because it is almost three years old, it is no longer under warranty. This washer will fill with water but does not spin or rinse the clothes. We paid a lot for this home and were so happy to get appliances that were all practically new. Now, we refused to have a repairman come and charge us lots of money to fix a washer that should not be broken. I have had washers run for 15 years and that was when I was washing clothes for 6 people, including cloth diapers for triplets! I will not buy any Maytag appliances. I will be getting an Amana or a Sears brand. Please, no one go buy a Maytag appliance.

So far after 5 calls and over two hours spent on calls IMPOSSIBLE to get an answer from Maytag about the correct fill levels of detergent. Consumer support simply do not know and refuse to direct me to anyone or have anyone call that does know answer. WHY SO IMPORTANT? Either you do not get clothes clean OR you damage machine and leave residue on clothes! Neither is acceptable. Using the fill level indicator on Bravos XL dispenser is in direct contradiction to any recommended levels on lids of high efficiency detergent manufacturers like Tide. Per Maytag manual only fill detergent to max fill LINE which is literally about two or three tablespoons of detergent. The lowest possible quantity of Tide per the lines on lid even for smallest load is two or three times the recommended fill level on the dispenser. No one has to be an engineer to know two tablespoons of HE detergent in dispense is going to do same effective cleaning for one shirt or towel as it will with a queen size comforter or very large full capacity load. CORRECT ANSWER DETERMINES IF YOU DAMAGE WASHER OR IF YOU HAVE DIRTY CLOTHES. Googling online there is also no answer. Such a critical answer for Maytag washer to work and clean clothes that is simply not available and documentation is wrong is a huge concern about the viability of this machine and worse their support. Our machine is less than two months old but is obviously over-engineered to the point of just being silly. Tip to Maytag: start selling washboards. More energy efficient, more green except for red and blue bruised knuckles, uses one tenth as much water and users do not need to spend their nest egg savings to buy. Not the first but will be the last Maytag product we will buy. Name may be same but the company is definitely not the company that used to enjoy that name with pride. SUMMARY: Maytag is adamant about using the correct amount of HE detergent OR damage and bad performance by washer and dirty clothes with a detergent residue. With all our best efforts we cannot get what that quantity of detergents is supposed to be. The user manual at best has ambiguous answer. The manual suggest horizontal measure of detergent in tray to max fill level which cannot be right. IF you instead use a vertical measure of how high detergent level comes up to the max fill line the quantity is radically different. It says dispenser holds 3 oz which would be beyond max fill level but nowhere near a vertical fill level.

This Maytag is about 7 years old now, at least, and is still running strong. The one thing I do miss, though, is the lint collector basket that used to be on GE washers Ive had in the past. Kleenexes have a sneaky way to getting into the laundry and picking out the remnants is a royal pain! The lint basket on the GE would save me that task.

If I could give less than one star I would. I purchased a Maytag range in September 2021, 33 days later the oven went out!! I have been fighting trying to get it repaired for months!!! The parts are not in, the parts have been shipped, oops we forgot to ship the parts, the technician is on vacation. You name it, I have heard it. After the phone call today, it looks like I will still be without a range at Christmas!! This is totally unacceptable. I purchased a Maytag because I assumed it was a good brand! Do yourself a favor... Never buy a Maytag or Whirlpool Appliance. Its not worth it. For the range to only work for 32 days is just plain Wrong....

I purchased the washer 12 months ago. I liked large tub size and Maytag name. Thought I had made a good purchase. Boy am I am sorry. The washer overflows my large utility sink for drainage on large load setting and clean setting, ruining the flooring in an adjoining room. You cant wash black clothes in it leave white residue spots all over clothing. You cant use pod soap. Doesnt dissolve totally. Just on your clothing so you must wash again. So now I am trying to figure out what I can do but afraid I am going to replace it. Would Not recommend this product. Bravos XL MCT MVWB835DW1.

This Maytag dishwasher works great if you are using as a sanitizer for your dishes so long as the dishes were soaked already. It stinks if you do not use it often and requires a lot of bleaching.

Wish I had read the reviews! I have had Maytag before and they were awesome. New purchase is horrible! Doesnt clean the clothes, leaves a residue on clothing and dryer does not dry properly. Called Maytag and they said use Affresh. Spent $10 on a pack of 5, and it did no good. My dark clothing is getting ruined! The washer is also incredibly LOUD! Very disappointed in this company and would never recommend them to anyone! I had purchased at Lowes, but had a delayed delivery, so I cant take them back, or I would.

Like most people with this Bravos machine, I am 3 months out of warranty and the ball bearing is trash. When the wash goes into spin cycle, it makes a loud clicking noise and takes a few minutes to start spinning. I called service repair and he told me that it was the ball bearing and to talk with them as he has dealt with quite a few high end machines from Maytag that are breaking down after warranty. I should have realized there was a problem when we kept coming up with white spots on our clean laundry and would have to re-rinse clean clothes. This kind of defeats the water saver that is advertised with the machine.Do not buy this product. For a high end washer and dryer, there are many problems. Maybe that is why the Maytag guy is not shown sleeping in commercials any longer. Hes too busy fixing all these machines. Btw, they wont cover the part even though I offered to pay for the service. The best they can do is give me 25% off. Yippee! I cant wait for the other problems to hit me like everyone else.

My Maytag refrigerator, model number mff2557heb, serial number 10375839gv, was purchased in 5/2005. Two weeks ago, this refrigerator stopped working. I called the Maytag technician and then right away came to my house and find out it is the compressor that needs to be replaced. He told me to search if it is under warranty. I searched in the internet Maytag compressor warranty and I found it and then called the Maytag representative. I told them I have found in their website that compressor of this Maytag is covered for 10 years but labor is not included. Then they asked me to fax it. I faxed the copy on 6/20 and they responded on 6/22. He said they received the copy and he said, Yes, it is covered for 10 years but you will shoulder the labor. So to make the story short, this Maytag representative scheduled Friday, 6/29 for the Maytag technician to fix my refrigerator. My husband did not go to work yesterday, 6/29, Friday, so he will be home for this Maytag tech. Maytag tech came at about 2pm yesterday and when he confirmed that it is the compressor that is the problem, he asked for the warranty paper. And when my husband present the proof, the copy of their warranty coverage that came from the Maytag website, he refused to work with my refrigerator because he said the one in the internet is not valid. It is really upsetting because I faxed the copy of it to them on 6/20/12 and they honored it. Thats why they arranged the technician to come to my house and then my husband did not work for them to work with our refrigerator and then asking me $79 for just saying that it is not covered by the warranty. I even gave them the model number and the serial number of the refrigerator so they can verify if it is covered. He said yes 10 years warranty on the compressor. In fact, two employees that I have spoken to both agreed that it is 10 years coverage except for the supervisor named Rachel. Her employees agreed to 10 years based on the paper that I have faxed them and it came from their website and they dont want to honor it after they sent the technician to my house. Thank you so much for your time and for reading about my grievances against Maytag employees.

I purchased a Maytag Dishwasher in March 2013 and the control panel failed in July 2014. I, along with hundreds or thousands of others it seems, discovered that this is an extremely common issue with several models of Maytag dishwashers. Rather than standing behind their products and making it right for their customers, Maytag is hiding behind their one year warranty and refusing to do anything about it or even admit they installed thousands of FAULTY control panels. This has been an expensive, infuriating issue to deal with and I have never been so dissatisfied with a company. Bottom line, they made a bad product that should have been recalled. It blows my mind that they are getting away with this. I wish I had known the recent changes in Maytag/Whirlpool and I wish I had done my research prior to the purchase.

The ceramic coating on the interior of the oven cavity in the top oven, which I use the most (may actually happen to the lower oven in time) has cracked in the exact pattern of the hidden element. When I spoke to the salesperson at the store, he wasnt surprised and said that it will eventually bubble and rust!!! Called customer service and was informed they consider this an aesthetic issue with no fix!!! They will not offer any remedy or compensation. Are you kidding me!!!

I purchased a matching set of Maytag Neptune washer and dryer about 6 years ago and the washer is junk! It sounds like a jet is landing in the laundry room. The repair man said it is not worth fixing - bad bearing. I am not happy!

I have a gas dryer from Maytag that works very well. Very easy to use and economical using it with propane. Im pleased with my purchase. Ive had it now for about 8 months. I would recommend buying another one.

I purchased this washer on 5-25-15. It was delivered on 6-2-15. It worked for 11 days. On the 13th, I called Maytag and made an appointment for it to be fixed. They said a technician would be out on the 16th to fix it. I got a call on the 15th saying the part they needed was not released yet so they would be out on the 23rd. The guy comes on the 23rd and diagnoses the problem. He says the machine has a bad motor and shock of all shocks. He doesnt have the part to repair it. They originally assumed it was something else and were wrong. Fantastic. He said he would be back on the 30th. I got a call on the 29th saying that, once again, the part needed to fix it was not released and that they would call me to make another appointment when it was available. I had enough. I originally purchased with Home Depot and called my original salesman. He told me he would replace the washer with any brand I wanted (I paid the difference in cost of course) but I was still relieved that he was willing to work with me. I ended up going with an LG. Lets hope that one works. I have 2 kids and have been having to go to the laundromat. I have to say that I loved the machine for the 11 days it worked! I would probably still have it if they had better customer service but Im not going to continue to put up with them not having whats needed to fix this thing.

New Maytag double oven installed by contractor in my house 18 months ago. I have had a few problems with it. The problem I am having today, the panel says error detected, remove from power source. I have had this problem a couple of times. I also have had the problem where the panel will not recognize anything I put in. I have to pull stove out of the small slot it is in, unplug and then push back. Not easy. I was the one that told contractor which Maytag range I wanted because I felt it was a good product. Problems from day one. This double oven/with range cost a pretty penny and I really cant afford a new one.

Same as all the other reviews control panel intermittently started to fail. Dishwasher is less than 3 years old. Does not work at all now. I tried resetting circuit breaker - nothing. This unit was $700 from Home Depot. Complete trash. It is cheaper to buy new dishwasher than repair - how unfair! Maytag won’t repair - well for over $300 they will. I feel better knowing everyone has same issue & is not my electrical system. Class action lawsuit!

I bought a Maytag washer in June and its the worst washer I have ever had. It has been 15 yrs since I had to buy a washer. My last washer was a Kenmore which was great. The Maytag does not have a water control knob. It has auto sensing which is crazy. I know how much water I need to wash my clothes. The water sensing barely puts water over the top of the clothes which is not what I need. My husband works in the oil field and gets oily and dirty. The next issue is the agitator that agitates the clothes. This one is a joke. The agitator starts agitating the clothes before the water is over the clothes and then when it needs to agitate it does a poor job. I am so unhappy with my machine that I am getting rid of it and looking for an old type washer. Evidently you made this washer for white collar people who do not get dirty. This is definitely not a washer for people who have dirty laundry. I am so disappointed with Maytag. I thought this was a good brand.

Our 3-year-old Maytag refrigerator, MFF2558VEAZ, is forming a sheet of ice on the bottom of the freezer. The ice partially melts for some reason, and then water leaks out at both bottom corners, usually once a day. Others have reported the same problem. Contact with a repair person is yet to be done. This must represent a factory defect.

Maytag msd2650kes refrigerator - I replaced compressor switch three times then compressor went out after only almost four years. We bought all new Maytag when remodeling. Never again will we ever be that stupid again.

In December of 2013, I purchased a Middle of the Line Maytag Dishwasher model #MDB8949SBW for $600 plus $200.00 for install and removal of 5 yr old Kenmore. At that time I thought I did my research and saw no major negative flaws on this type of machine or similar machines. This replaced a 5 yr old low line Kenmore that just upped and died. Installed just before the holidays, this Maytag machine seemed to have worked tirelessly until a few days ago August 18/2015. The computer controls went haywire. I was hitting normal start buttons and other buttons on the other side of the control panel were blinking and lighting up. Worse was trying to cancel and the control boards were not responding. Even hitting the start button, the machine would not turn on. Finally looking at the facia, I see the tabs of the flexible plastic frame that hold the control panel popping out from underneath the white facia plate. Snapping the frame back in and applying a lot of pressure got the machine to operate. With a family of four and minimal storage space, this machine is used approx once a day. It appears over the year and 1/2 by pulling on the plastic handle - which also happens to be the computer control board frame, the computer has separated from its mount and has allowed moisture to hit the control board/computer and wreak havoc on the electronics. Looking up this model online NOW, I see I am not the only one with Dishwasher computers failing within a year or two- just out of the one year warranty. A Call to Maytags customer service has the computer control board alone cost $160.00 plus the service tech and his labor fees reaching in excess of $450.00. The CS rep gave me a repair discount to $267.00 and a week wait for the Service Tech for this problem to be fixed. I bought this machine on two premises - one for its price, it was the only machine that offered 3 spin jets that really do a good job in cleaning dishes and 2, I owned a 1984 Maytag dishwasher in another home with computer controls in the handle and to this day, that machine is still running flawlessly! My only issue with the 84 Maytag machine was after 4 years the door gasket went - too much soap - replaced and no issues since! I expected similar performance with this one. I guess I have to spend north of 3 bills for similar performance and quality. What was I thinking?

So for the past year our 1 yr old freezer has been leaking and holding a sheet of ice at the bottom. Ive been wondering why my electric bill has skyrocketed the past two months and we just realized that the freezer wont even stay closed anymore. Maytag has become a VERY POOR product. Our less than two year old $450 Maytag Drier just busted as well. After paying repairman after repairman and replacing different parts, we had to get rid of it. I am very dissatisfied with Maytag and will never purchase a product with their name attached. Please keep us posted if there is a class action lawsuit. This is unfair to make a product that fails immediately for the price that is paid!

My Maytag MDB7749SAW0 Dishwasher starting acting up after around the first year. The lights on the Control Panel began to flash uncontrollably and it will run all day while I am at work. I called Maytag and they were nice but did not repair it because the warranty just ran out. The person on the phone said that it is a common problem with knob-less dishwashers, the humidity causes problems with the control panel. The cost to repair was over $300 to replace the control panel.

My home has all Maytag appliances, all just over 2.5 years and I have had no issues with any of the other equipment excepting the fridge. The fridge itself works very well when it does, but some things are just wrong/flawed with the French door fridge.1. The Evaporator mechanism is flawed and keeps accumulating frost over the Thermistor sensor, which in turn shuts off the fan and the fridge itself stops cooling rendering all the produce bad within hours of purchase. The freezer and icemaker works fine during this time. The first time a tech came in during Warranty period and put come Aluminum foil over the thermostat and zip tied it and told us that the issue is resolved. Fast forward 18 months or so, same issue. This time they want to replace all parts since the last time it did not fix it. How convenient isnt it? So now I have to shell 500 plus bucks to solve what was not fixed the last time. Flawed design is all it is; do not purchase any of the French door fridge from Maytag/Whirlpool or be prepared to buy an extended warranty and a down fridge every 12-15 months at the minimum. In my case shell out 500 bucks every 15 months I guess.2. Sloppy icemaker: Ever heard of an icemaker that thinks and drops 4-5 cubes when requested and thinks again before giving another 4-5 cubes? We see it all the time at Soda fountains. This is what to expect off a Maytag ice maker. And lord knows if you have guests, they will run through the batch of ice by the very first meal and then the princess ice maker needs 12 hours to make another batch of ice.3. Noisy fridge: Ever heard a noisy fridge in a very quiet home? This Fridge excels at that. Just about the time it shuts off the compressor, boom it goes on again.

Bought the washer in February 2012 for $900 at a local appliance store, delivery included. Just yesterday (10/16/15) a 5 cent piece of grey plastic flew out of the lid lock mechanism. Thinking this $900 modern piece of machinery painstakingly designed by intelligent people with university degrees would certainly work if I just stuck the plastic part back in. I just popped it back in, the lid locked, and the machine spun away happily (only having to run a correct cycle for an unbalanced load twice! What joy!) Fast forward 40 minutes, I skip down the stairs to go retrieve my flannel sheets (because its October in Pennsylvania, its getting freezing cold at night) and pull up gently to open the lid. It doesnt budge. About 2 hours later, following a screaming match and some furious googling, it was determined we would need two people to pop the entire top off the machine to extract my sheets.So in order to use the washer to clean clothing now, weve been unplugging the machine. Removing the three screws on the control panel (aka brainbox), unplugging the black and white wire from the brain box, taking the control panel off and sitting it on the dryer, and using putty knives to push in the metal clips holding down the top of the machine down, and prying the entire top of the machine back on its hinge. Then I can get my clothes out. Then doing so in reverse (dont forget to add detergent before shutting the lid! It will lock and you will have to pop the entire top off again.) to use the washer. All because of a 5 cent piece of PLASTIC. What brainchild figured, Eh, we can just use plastic for this important piece that the washer wont run properly without. It doesnt matter!? Someone that wanted to make $300 a pop doing service calls thats who.I cant believe Maytag has gone so far down the tubes. In case anyone else ran into this problem and needs to fix it, write down the model number, serial number, and other crud listed under the lid. Then use them to wipe while youre in the bathroom. All you need is the company and part number on the lid lock mechanism. According to Maytags website my washer doesnt exist. And there was no way, no matter how creatively I googled, to find a part for it with the Maytag model number. So now I have to try to find this measly mechanism to replace and try to use this piece of crud for a few more months. I guess my Christmas present this year is buying a new washer. And you can BET it will not be a Maytag.And two more things: with no agitator, you can fit really big stuff, but you also get to hear your washing machine dancing on your basement floor with an uneven load. No matter how many times you try to re-position items, it runs a corrective cycle, refills with water, and spins everything into a ball AGAIN. Also, the miserable thing is starting to rust. Right on the sides and near the lid hinge, and all around the bleach receptacle. How cheap, a washer on which the paint rusts right off with chlorine bleach.I wish I still had my Grandpas old 1930s wringer Maytag. At least I knew that one would work without a cheap piece of plastic. And at this point I might prefer wringing my clothes to hearing my washer try to escape. In short: cheap parts, no replacements available through company for DIY repairmen, company designed to force customers to use their servicing for $300 a pop. 1/10 would NOT recommend Maytag.

Ive tried all manner of washing clothes, especially dark ones. Different cycles, different detergents and amounts, but it always leaves scum marks in folded places. I have to either brush off what I can, and/or rinse the clothing in a sink and then rewash the clothing without detergent. In an attempt to save water, I end up using two or three times the amount.

My dishwasher is less than 2 years old. Dishwasher will go on when we are not in the house. Cant control the panel. The control panel lights all come, have to cancel to stop the machine. This could be a fire hazard.

I purchased a small (14.5 cubic feet) refrigerator for my basement from Home Depot on January 26, 2013. It was delivered on January 30, 2013. On February 14, 2013, we found that it was not cooling like it was supposed to. The soft drinks in it were not cold. I called Home Depot and was told I had to call Maytag for a repairman to come out. Since it was so new, I felt it should be replaced. They disagree. The warranty only calls for repair. So a repairman came out on Feb. 19th. He said that it has no freon. He doesnt know why. It could have a leak. It could have leaked out in the warehouse. There is no way to know this. He said another repairman would be out to fix it on the 20th. On the 20th, no one showed up or called. I called the repair company, S & S Appliance of Bessemer. I was told the repairman that I needed is in Montgomery today and the repairman yesterday was told to tell me he would call me. He was told to not tell me someone would be out today. So now, I have to wait until tomorrow for someone else to call me and see when he can fit me in his schedule. I think Maytag has a problem with their refrigerators. I think Home Depot has a problem not standing behind what they sell. I think S & S has a problem with their servicemen. I am not happy with any of these companies and will never buy another Maytag refrigerator or washer, but thats another story.

Not long after dishwasher MDB7609AWB2 was out of warranty the START switch on the keyboard would not work. Called dealer and they sent someone out to check for a charge not quite $100. Could not fix it so said it needed a new control panel which with labor was almost $200. Doesnt work so get it fixed. Now less than 3 years later the same thing has happened - wont start. Lousy engineering and part probably made in China to save Maytag money, I feel is the cause. This is happening over and over to those of us who purchased in good faith what used to be a reliable product from a reliable company.

The washer w10420491A is 2 1/2 years old and got the F51 code. The result is the hub bearing are shot along with a circuit board. I would stay away from any Maytag Bravos washers.

Bravos XL Top loading High Efficiency Low Water Washer and Dryer - I gave this washing machine a 1 star but would give it a 0 star or less if the choice was available. I agree with everything others have voiced about this washer. I end up using the bulky cycle for everything because it is the only cycle I have found that will use enough water to get the clothes moving around. All the other cycles are a joke. First you must put everything around the wall of the tub away from the so called agitator. Then about 2 cups of water enters the machine. It then goes into this high speed spin. In my opinion it just pushes any soil deeper into the fibers. The drum will then spin slowly and water will spray on the clothes for several minutes but the washer never fills with enough water to cover the clothes. Watching it agitate through the glass top is almost hysterical. Laundry is barely moving. The high speed spin they push as a selling point puts deep wrinkles in everything and the wrinkle control setting on the dryer does nothing for them. It is absolutely the worst machine I have ever owned. My husband has repeatedly told me to sell these and buy another set. I will be ashamed to sell it to anyone. Im not sure how the makers of Maytag got away with selling these machines. I know there are different models but from what I have read they all work the same. I replaced a very low end GE Washer and Dryer with this pair and every time I do laundry I wish I had them back. The matching dryer is very costly to run as almost every load takes 2 cycles to get items dry. Nothing comes out completely dry even if you put it on the more dry setting.

Just when you think that youre able to do laundry. First, comes the musty smell. So, you clean cycle your HE machine using only the cleaning product directed by the manufacturer. Then, comes the pump being stuck on. Like it still have to drain yet your clothes are soaked but you heard full force of a good drain. Poof. Unplug and kick it. Look on YouTube and discover you should take it apart and clean out some obscure puddle holder & look! You discovered where the sock monster lives...its gross. Going to start my own business (125.00) to clean these things out. Hopefully not get some kind of fungus from the grossest mold ever. Its Maytag not a Home Depot issue.

Purchased a Maytag Centennial Washer from Lowes. This is the NOISIEST WASHER I HAVE EVER HAD. Self Balancing, pretty much the way it is, YOU lift that heavy wet laundry and re-arrange to balance. It just slams around even moving the washer, until you do. This washer also doubles as a BLENDER. It SHREDS laundry. The agitator does not go all the way down and thus, clothing, towels, rugs... get stuck under the agitator, wind around and RIP. Have had hundreds of dollars worth of laundry shredded such as: shirts, towels, new rugs and it even ripped the waist off a pair of my jeans! The other laundry gets tied up on the stuck laundry and you end up with a twisted, ripped, tied up Laundry Ball. It will not wash or rinse well when it does this, naturally. Lowes: The salesman knew about all this, and sold it anyway! He had one and got rid of it. Gee thanks Lowes and Maytag, for the worst washer I have ever had the misfortune of owning.

This dishwasher is reliable and has NEVER had any repairs. It cleans fairly well, but I do wash off dishes before I put them in. The one complaint I have is sometimes the dishes smell funny after washing. I think it may be our water though. I also like that there is room for oversize dishes and glasses on some of the racks. Overall, I would buy it again.