My Maytag dishwasher which is less than 2 yrs old had its control panel and board gone bad. It took almost $400 to fix it. It seems like an ongoing problem and Maytag does not do anything. I would have bought a new dishwasher for that price, but I was already in for almost $200.00. They dont give you prices upfront.

Zero should be a choice on overall experience. I purchased a Maytag Bravo 300 from Lowes in February of 2011. Last week I was doing a load of laundry and the washer stopped in mid-cycle, and it gave an alarm and error code ld. I checked out the manual and it said there was a problem with the drain line. I check the drain line and it was fine, so I called Maytag to have a service man take a look at it. Before he even looked at the washer, he said it was probably the pump, and it is not covered under warranty. And he said that it would cost $140. He obviously sees this all the time. He explained that the pump is too small for the unit and it does not allow anything to go through the pump. Please make sure anyone who may be considering buying one of these units knows right up front that they are going to have issues with the pump, even if a small pebble gets caught in the pump.

The water drainage tube on the Maytag Refrigerators is DEFECTIVE and needs to be replaced during manufacturing of the appliances!!!!!!! The existing drainage tube kit in the appliance has a very tiny opening for the water to drain and what was not factored in during this manufacturing of the refrigerators was bacteria and dirt build up from the water draining to CLOG this very TINY opening in the existing drainage tube system. This results in the water having no place to drain except causing an ice build up in the freezer and then water draining onto the floor when it has no where to drain in the appliance. I am told by my reputable Maytag repairman, who also needed the same repair, that replacing the water tube drain #W10619951 occurs with customers 4-8 times PER WEEK in his practice. This is obviously an ONGOING defect that Whirlpool is IGNORING and needs to be addressed and corrected with some type of compensation for its customers. The service call and the replacement of the drain tube kit #W10619951 cost me $122.31. My Maytag refrigerator with a bottom freezer is less than 3 years old.Amazing also if you google MAYTAG refrigerator leaking water there is a MULTITUDE of youtube videos and websites instructing the consumer on HOW to replace this part in the refrigerator. Obviously there is a strong need for this instructional information to the consumer for this repair since it is an ONGOING PROBLEM that has not been addressed legally with manufacturer. Action needs to be taken. I am saving the original part that was removed from the appliance in case a class action remedy is necessary to correct this costly defect in the Maytag Refrigerators.

I got a washer from a Menards Store in Fond du Lac, WI. I was given a line of crap at how great it was, and because Ive used Maytag for years I bought it. Id rather have my 20 plus old one back. At least it didnt take over an hour for a load, and the rinse cycle really worked. WE HATE YOUR NEW WASHER. As soon as we can afford a different washer well be looking for a different brand.

I bought a Maytag Washer in October of 2012. So far we have had to have repairs to it (4) times. The motor falls out. We are very dissatisfied with the product. We have always purchased Maytag products and fee we should get a new washer. The warranty is up in one month. If there is anything you can do to help it would be appreciated. A $1,000.00 for a washer is a lot of money for something that does not work and takes a week to get a repairman. Thanks.

I purchased a washer & dryer from Lowes on December 3rd. On February 20th, my washer stopped filling up. I called customer service and had someone come out a few days later. The repairman said the sensor broke & it would take 10 days for part to come in. After 2 weeks, I tried calling repair company and they would not answer phone for Maytag, or me. Maytag called another service provider, and it will be another week before part comes in. Never could get in touch with anyone who was helpful! Now it’s been a month, and still not fixed!

I also bought a Maytag Neptune MAH5500BWW and matching dryer model #MDG5500AWW in 2001 and within a month, I called Sears and Maytag. I told them about the terrible odor and mold growing. The repairman said it is normal and told me to use Tide detergent once every two weeks. The dryer had a major breakdown and I had to buy a whole header with all the electrical components. I too bought the brand name Maytag due to a good reputation that Maytag had. I never received a recall notice or anything from Maytag. I will never buy Maytag products again. I found out from a salesperson at Sears that Maytag was sold to Whirlpool. The salesperson said the reviews are terrible for Maytag products especially for my models. I will never buy from Sears, etc. What can you do for me? Maytag and Whirlpool need to take their responsibility for their products! I am truly lucky I did not buy a plane from them. I and a lot of people would be dead.

I bought this Centennial washer about 7 weeks ago and it has worked right for 4 of those weeks. The washer wouldnt spin the clothes and they came out soaked. Service guy came out and said it was the computer panel and he didnt have one. So I waited over a week for another service call. He put that one and said that now the transmission was shot and he didnt have one, another wait. This is a piece of junk. Do not buy Maytag or Whirlpool products. I had a Maytag for 15 years and had one service call. They are not what they used to be.

Maytag may have pay to replace defective controls. 1-866-931-7384 is the number to call. I have owned my maytag dishwasher for about 18 months. Its control panel was never great, but now my dishwasher wont work at all. Apparently, the tiny inside the control panel rust away because they arent sealed.

My mom decided to splurge on a new Maytag Bravos washing machine and matching dryer thinking that at age 80 the machine would outlast her. But no. After 4 years and just past the warranty, the timer started going crazy. The repairman recommended a $250 motherboard and $90 pump and $500 labor (yes he is next on my list) and it still does not work. I WILL get her money back for the repair and we will NOT be getting a bravos to replace it.

We purchased a Maytag convection oven less than a year ago! Today is the 3rd time the heat sensor has gone on it! I want a new stove! I am beyond disappointed with the business and the product! Have always bought Maytag! Rethinking it now!!!

I have a Maytag Centennial washer & dryer put into service in August 2011. The washer has recently gotten quite noisy, so I had a repairman out to look at it. He found that the bearings are going out & estimated repair costs at $360. He actually did not recommend repair, as the repair costs approach half the price of a new washer. I am very angry about this, as this is quite a new washer & was not a cheap model. There are only 2 of us in the house, so I only wash an average of half a dozen loads a week. I never jam the tub full, basically baby the washer so it will last. Much good that has done! Im old enough to remember when Maytag was the best in laundry appliances, expected to last for many years. I bought the Maytag because my last (top-of-the-line) Whirlpool set required a number of repairs, not realizing that Whirlpool had purchased Maytag. I will be using this washer until the bearing seize & then I will be buying a non-Whirlpool product Im afraid that will mean a foreign brand. I really prefer to buy American, but apparently, thanks to Whirlpool, that is no longer possible!

We are extremely frustrated with this machine. It takes an extremely long time to go through the cycle, compared to past washing machines, even when it is working. It rarely completes the cycle and often goes back to wash and stops. We have no way of knowing if it washed or rinsed or what. To get it to finish, we have to turn the dial to drain and spin. The clothes always come out tightly twisted and tangled up and have to be untwisted and items pulled from each other....so they are extremely wrinkled! This is the first and last Maytag product we will ever buy. We HATE it!!! I would say it has been a lemon from day one but Home Hardware was no help when we complained. We tell everyone to stay away from this product.

Why is no one doing anything about the crappy product that Maytag is putting out. I am a single mom of 4 and I had to purchase a new refrigerator about 3 years ago. Spent a lot of money on this Maytag, approx. $1400 and it is now useless. I had nothing but issues with it from the time I got it. The bottom freezer kept icing up and then leaking all over my kitchen floor. I had to call a repair guy out, who charged arm and a leg and said it was fixed and 3 months later it was doing the same thing. Since I could not afford to pay ridiculous amount of money to repair it again (although I question what they said they fixed), I had to chop up the ice each month and take huge pieces outside and i had to keep towels always at the bottom of my fridge (yes very attractive) but it ruined my floor and carpet. Now all of a sudden the piece of junk just shut off and stopped working and keeps making this popping noise. Lights went out in front panel. So I had to call a service guy out again but this time I called an independent local guy that is not gonna rape you in charges like Maytag does and he told me to look into this that he has heard so many complaints that the front board with control button has been known to blow out the back circuit board, which is what happened. He told me that parts are MDs, so he would have to get another manufacturer and he heard that even with replacing both of them, it has been known to not work and Maytag takes NO responsibility at all for any of this. THIS IS WRONG. I cant afford to spend around $800 to now fix this or another $1,400 to buy a new one. So I am without a refrigerator. What a nightmare. MAYTAG, TAKE RESPONSIBILITY FOR YOUR CRAPPY PRODUCT. We are hard working people that spend our money and expect a good product. I also have an oven I bought and I can tell you it is a piece of crap too. I swear at it all of the time, as it takes forever to cook anything and the outside that is supposed to be stainless steel is all yoked up. It is like a tin can, looks horrible. I will never ever buy another Maytag product and I hope that ConsumerAffairs steps in and does something about this.

I got no help whatsoever. I will never buy in Maytag again. My washer has had 3 problems in 1 year. They tell you that they will send someone out the next day but they dont come until 4-5 days later.

Bought the Maytag top load high efficiency washer (also matching dryer which works perfectly) brand new less than 6 months ago. It is the worst. It leaves swirl marks on my clothes that doesnt come out. Leaves part of clothing dry without being a large load! If I put sheets in there it blows up like a mushroom and leaves that part dry. I use the correct detergent. I had a serviceman, that the manufacturer suggested, check it and determined there is nothing wrong with it which only leads me to the conclusion that it is a poorly designed product. Spoke to a manager at Maytag that said the machine works fine. And because it is in a business setting there is nothing they can do. (What? If it worked fine, I wouldnt be here.) Called to company I bought it from... Theres nothing wrong with the machine plus we are closing the business so its the manufacturer warranty that you need to call them. I would have been happy with a exchange. Poor design, poor customer service.

I have had my washer and dryer for about 5 years. After a couple of years, I noticed my washer would fill and stop. When I go to put clothes in the dryer, it’s still filled with water... very inconvenient! I have to open and close it and then it continues. The dial doesnt work properly! The delicate cycle hardly works... that started after about a year. It just freezes up and stops. I have to open and close it. It does not rinse right, leaves a film on dark clothes, and I have to rinse again; I do not over fill it either. Sometimes it does smell a little mildew.The dryer knob does not work properly. I set my setting and pull the knob out, and it doesnt come on. I have to do it several times or change the setting or put it on 30 minutes only... very frustrating! I never had these problems with my Kenmores! I wish I did not switch brands. These things should work properly. I realize washers and dryers dont last like they used to, but come on! They also cost so much more than they used to. I wont do this again. I will do more research as to what is a good product. Too bad!

I purchased a Maytag refrigerator (MBR2258XES4) from Home Depot in 2012. I bought a five year extended warranty. It started leaking at the bottom. Repairmen said defrost drain clogged not covered! Cost: $180. DO NOT BUY MAYTAG, N.E.W. (Asurion Co.) warranties or Home Depot appliances! This is text book deceptive advertising. At no time did Home Depot associates in Kitchen and Bath departments say that this common design flaw existed and that it was not covered under the N.E.W. Asurion warranty which cost me an an additional $150.00! I am interested in joining a class action lawsuit against Home Depot and Asurion Co (N.E.W.) warranties.

I believe the Maytag Bravo washer and dryer was manufactured so the Maytag man would have something to do once again! Buyers Beware! My $800 washer broke down 1 week after warranty costing me $400 to repair!!! Half the cost of a new one... now the dryer is making horrible noises. I fear calling for repair... or should I just buy a new different one?? My last washer and dryer lasted 30 years!!! Bravo certainly did not have all the kinks out of them before marketing them! The cost is to the consumer who trusted the name! You cannot return a 2 year old appliance! The laundromat would have been less costly than this washer and dryer! Maytag should be made to recall these defective machines or at least repair for free. Do not buy!

After 18 months of use Our Maytag Dishwasher (MDB7749) has the same control panel problem as a lot of other user complaints. I wish I too had read the consumer reviews before my purchase. We will never buy another Whirlpool product!!

Almost two years after purchasing the Maytag Bravo XL, I am fed up. I have the exact same problems as everyone else in these reviews. Soap scum left on dark clothes since day 1. I thought maybe I was doing something wrong. I have read and re-read the manual especially the troubleshooting guide and still have the same thing happen. Its very frustrating. I constantly have to re-rinse clothes because of soap, lint, dirt, etc left on clothes. I wouldnt give away this washer to anyone, I would rather burn it. I am currently looking for a new washer, the last one I had for 11 years was a front loading Whirlpool. I should have stuck with a Whirlpool, I still have the matching dryer no problems at all.

I purchased both a Maytag Neptune washer and dryer in 2007. This is without a doubt one of the biggest mistake I have made. I have had the dryer drum and rollers replaced and the washer will no longer run. It is going to cost me hundreds of dollars to repair. To think I bought these units for 2 reasons: 1. that Maytag are the dependability people, but its not! and 2. Energy efficiency. It is not too efficient when they are broken more than they work. The worst was when the repairman told me that I had purchased the worst product on the market. These units are in short, garbage! I will never buy another Maytag Product!

My Maytag dishwasher is very easy to use. Saves on money and time. I enjoy it and it have made my life so much easier. When you cook for two you can be out the kitchen in no time.

To begin with, the Bravos 300 washer was bought because we owned a Maytag previously and it was with us for 25 years. It was still running when we gave it away and the only problem was a small oil leak starting at the drive. The new washer has no agitator, just the new style flat thing at the bottom of the tub. You cannot wash a set of fitted sheets without it turning into a tangled mess. The washer quit working after about 5 years and all indications pointed to the control. The control would reset after unplugging, but would freeze immediately when you tried to enter a command. We live in an isolated place and it is not feasible to fly in a service person. I ordered a new control, but there was no change in function. After several hours of detective work, it turns out that the mickey mouse plug for the electrical connection at the pump had broken inside. Because the pump would not work, the whole control would freeze. We will never buy another Maytag.

Whos up for a class action lawsuit against Maytag? I believe Maytag is making claims that are NOT true. I bought a new Maytag Bravos XL in Nov 2015. I asked the salesperson to point me to a deep water washing machine for Large loads. Salesperson sold me the Maytag Bravos XL MCT and made claims I would have 30% more water than the other washers. The sales pitch (according to Manufacture) is these smart machines have sensors that can detect how much water is needed. THIS IS NOT TRUE. My Maytag machine only gives me 1-2 inches of water on the normal and rinse cycles and maybe 4-5 inches on deep water cycle!!! Certainly not enough to cover clothes, towels or sheets. I immediately called Sears. Tech is basically being trained to tell consumers thats the way it is. This is the new future in washing machines. So, My recommendation - hire an attorney to get your money back!

I purchased the Legacy series washer and dryer from Home Depot in 2005. For the first 3 years, the washer worked fine. Since then, it has all been downhill. When I use bleach, I have to run an empty load because for whatever reason, the bleach goes through to the next load which has resulted in a number of ruined clothes. The wash cycle leaves clothes dirty and some even come out partially dry?! The rinse cycle does not always work as more times than not, the fabric softener is still in the dispenser cup. The spin cycle is getting worse with each load. Sometimes I reset the spin cycle as many as three times at which point I hand wring the clothes. This creates a strain on the dryer as I have to run it extra long to dry the clothes. I am more disappointed than I can say. I will never purchase anything Maytag again and I will not purchase from the company who makes Maytag products.

Bought Bravos XL washer and dryer about 4 years ago at Home Depot. The dryer is fine. The washer not only doesnt clean the clothes unless you have it on rapid wash - but every person that is here when I wash clothes is shocked at the noise coming from it. I always say my laundry plane is landing or taking off. Its out of control.

I purchased an LG (white) washer last year, but my husband upgraded all appliances to stainless, including Maytag washer and dryer. The washer does not fill with enough water to cover the clothes. It barely agitates them to wash. Some clothes even come out with dry spots on them at times! They smell and are still dirty when done. I have tried every setting hoping that was the issue. Normal, power wash, none work any better! Had to resort to the soak function which does not add fabric softener or drain the water completely. Thankfully I didnt sell or get rid of the LG. Putting the LG back in asap. Nevermind the mixed color finishes of white and stainless between the washer and dryer. Clean clothes most important! Piece of garbage and complete rip off!

I have been the latest victim in purchasing a Maytag Refrigerator. Something needs to be done about the defective products they are putting on the market. I received 9/7/13 (yesterday) a new Model FW: 555 Complaints and Reviews about Maytag Refrigerators bottom freezer refrigerator. After being plugged in for 3 hrs, the temp was 60 degrees.. After 8 hrs same and 24 hrs same. I lost everything because of the defect. I notified the store 3 hrs after purchasing it and because I had it delivered on a Saturday I have to wait till Monday to get this resolved. I want everyone to read before buying a Maytag product.

I wrote earlier about my dishwasher needing to have an electronic board replaced again. So I called the helpful (I say that with sarcasm in my voice) 800 number. My dealer asked me to call for help with paying for the new part. After an hour and a half of being cut off and put on hold, I finally got through to a person that could take my request. The gentleman explained to me about why they would not stand behind their product which was only 3 1/2 years old, and a replacement part that lasted only 11 months. He expanded on his thought about how it was too old to fix and the part was more than 90 days old. I am out of my $1,100.00 with no help in sight. Totally upset with this company and how they will not stand behind a poorly made product!!!!

We have had our Maytag dishwasher MDB9100AWQ only 5 years and now it keeps shutting off. I see there is plenty of this complaint. I will not purchase another Maytag product after reading all these reviews and experiencing it.

Centennial commercial tech. washer - We purchased this piece of junk in Sept 2013, and had to have a repairman twice before it was six weeks in my home. I wrote several letters but the only thing that I received were applications for insurance to cover repairs. I should have received a replacement as it was bad from day one, but Maytag doesnt replace!!! Its been semi-reliable for the past several months, until early this year. It started jerking when it changed cycles, sounding as if the drum was hitting really hard against the sides. It has continued to do that regularly; now it wont function on the cycle its set on. It wont spin, sometimes the lid lock wont work. It starts filling when it should be draining. This evening, it stayed in the rinse cycle for 40 minutes and when I realized it was still rinsing I had to unplug it to get it stopped. It goes on and on, (and so could I out of frustration). The good name of Maytag has turned to trash, and when it leaves my home, no more Maytags!!! PS. The dryer we got with it takes at least 1 1/2 full cycles to dry a load, and since I couldnt get it to spin properly, Ill be lucky to get this last load dry in 2 to 2 1/2 cycles.

I purchased a Maytag Bravos HE top loading washing machine two years ago. The clothes hardly get wet enough to get clean. It leaves a residue on dark clothes and the basket goes unbalanced at the drop of a hat. Whatever you save in water, you spend on electricity because a cycle takes twice as long as a conventional washer. It goes out of balance and bangs the machine enough to walk it across a room. I purchased this machine from an appliance store, not some discount house. I have had machines last 20 years and this one is shot in 2. I will never, ever purchase another Maytag, Whirlpool or KitchenAid product again ever.

We purchased our Maytag through Sears. We wanted a very basic machine, and thats what we found at Sears, yay! Fast forward eight years and it suddenly quit agitating. We tried fixing it ourselves by replacing a plastic gear part, which, later on our appliance technician said was totally logical, but it still wouldnt work. We got our appliance repairman out here and he took it into the shop and fixed the problem, which turned out to be part of the motor or something like that. The thing that bothers me the most is that he asked if we had bought a refurbished washer, but we hadnt, it was brand new. He gave us a part that was swapped out that wasnt made for the machine and also said the safety guard for the cord was missing. This keeps it from pulling out of the machine in case it gets jerked. I feel deceived and just wanted to vent because there really isnt anything I can do about it now. Buyer beware, yes, but I know we have to be our own technician sleuths to be sure were getting what we paid for?

I purchased this range from a Maytag outlet in Nov. 2006. No problems with it until Nov 2015. The oven igniter failed. This was serviced locally and replaced in an efficient manner by the local service tech. All is good until 2 days later when I decided it is time for an oven cleaning cycle. I set the cycle for Medium Soil (3hrs). After the conclusion of the clean cycle, the oven (bake) would not work. Called Maytag service, the service tech replaced burned up oven wiring as well as the igniter again. However, the cleaning cycle had taken out the gas safety valve control as well. I am now told there is no replacement oven gas safety valve unit available anywhere. I even called Maytags 1-800 number and searched online only to find the part on backorder and not available.I find this particularly frustrating in light that I spent over $1200 on a Maytag product I thought would bring way more than 9 years of service before it is deemed unrepairable. The average gas range lifetime is 18 years. In my opinion, not a good return for the investment. Its a shame because the rest of the range works and looks fine, which is now destined for the dump. I am replacing the Maytag with a $550. Frigidaire with manual cleaning. Will never buy another Maytag appliance or a self cleaning oven again. If the self cleaning feature has the potential to fry the controls, why would they offer such a feature, or why couldnt they warn one of the potential failure.

Purchased matched set washer/dryer on May 21, 2013, machine always took over 1 hour to dry medium load of laundry, but dealt with it. On June 5, 2014 made a horrible bang, followed by a grinding sound, ran to turn off. Hubby took apart, thanks to Youtube video and found that a screw was lodged in the fan blade, had broken a tooth and the motor mount broken....took fully apart, ordered fan blade to replace. When went to put back together, realized the WALL (bulkhead) of the dryer was broken, metal was too thin to support the tiny bracket to hold the motor.Called Maytag, NO HELP, told me to call a local repair guy for an after warranty service. Called repair company and was told he has NEVER seen this in a newer model dryer, contact Maytag, contacted them again by live chat and told not under warranty and no one has ever had this problem. Do NOT buy anything from Maytag. THEY DO NOT BACK THEIR PRODUCTS! If you have had this problem contact me, Im willing to spend a day or two in small claims if necessary to prove my point!

We purchased the Maytag MDB8959SAS0 dishwasher about 2.5 years ago. A couple of days ago, the lights on the control panel started blinking and beeping erratically. I contacted Maytag and they said the control board likely needs to be replaced to the tune of around $250, not including labor! We spent $800 on this dishwasher and it cant even last 3 years?? Ridiculous. The only other advice the service rep. had was that we should have bought the extended warranty. Gee, thanks. I guess with Maytag, you really DO need that extended warranty because their products are junk. I think I will just scrap this dishwasher and go with a Bosch. We also have a Maytag range that needed servicing after owning it for only 18 mos. And a Maytag dryer that needed servicing after a month (at least that was under warranty). I will NEVER buy a Maytag product again... they are complete junk.

I am also frustrated with Maytag for the same exact problem... The control panel and the dishwasher not working just after our year warranty went out. I purchased this product because we had a good experience with a Maytag Dishwasher lasting about 20 years, only to get fooled that the quality is not there any longer. This seems like BAD business on Maytag, Whirlpool, and Home Depot! How can we get an official complaint to someone who can fix this? Another example of big businesses that do not care to take care of customers! Why would a company like Home Depot continue to support this business!!

I purchased this dishwasher about eight years ago, and I love the performance and the stainless steel interior. I never have a problem getting my dishes clean. This product definitely lives up to its reputation. Going forward, I would definitely buy the same brand if it became necessary.

Why are the clothes in my dryer getting stuck in Maytag Neptune? It seems there is a little opening around the rim of the barrel in the back of my dryer that drawstrings, zippers or similar small parts of the clothes can get stuck in. It twists the clothes around and is ruining clothes, also is making a thump-thump sound. Someone, please help!

This is a continuing aggravation! On July 27, I discovered the dishwasher (MDB7600AWW) tub had developed a crack in the bottom right rear and had warped my countertop and the floor under it was full of water! I called the appliance store where it was purchased and was told to call Maytag. I have a 20-year warranty on the tub with free replacement of the unit if it fails. I called Maytag and was told we needed a service call to verify. I scheduled it for July 30, and 3 minutes and $75 later, yup, tub is cracked. Its a known problem, and the dealer has already replaced some for customers. I called Maytag to get the ball rolling for replacement. I spoke with Jennifer and was told shed get back to me.Meanwhile, we went to several stores, checking out other Maytag models. So, Id have some idea of what was available as a replacement. I called Jennifer on July 31 with a suggested model Id find as a suitable replacement. She said shed check and get back to me. On August 13, I called Jennifer for some answers, got the voicemail, and left a message. On August 14, I went online to chat. Finally, I was told Id have a replacement in 10-12 days. Id be contacted to schedule installation. On August 16, I called a local dealer again. He cant understand the problem. Hed replaced two others in a few days. He made some calls for us and gave us the name and phone for the company replacing the dishwasher as well as the work order. Installation was tentative for August 23. (Hed been cut out completely!)I called Optimus Solutions, and theyre awaiting shipment. Tentative installation was on August 23. On August 22, theres still no word. I called Maytag customer service. Sorry, it was shipped to the wrong address, so it was shipped back! Its now in transit and supposed to be delivered to Optimus Solutions today but not being scheduled for installation until August 31!This has become one nightmare after another with everyone pointing the finger at the next guy. Phone calls get only the same runaround. No, speaking to a supervisor wont help - theyll tell me the same thing. Isnt that convenient! Meanwhile, Im still washing dishes by hand and having psoriasis on my hands, which are like two pieces of raw meat right now. It is beyond aggravation; its bordering on torture! (No, I cant wear gloves. They make my hands sweat and even more sore!) Besides, I shouldnt be washing dishes by hand. I paid for a dishwasher that failed through no fault of my own, and now, Im being punished for purchasing it. I can guarantee that if I had no warranty and had to replace this dishwasher, it would have been replaced immediately!Never again. I purchased all Maytag products for my new home. As they fail, I can guarantee I will not be replacing them with Maytag or Whirlpool, which now owns Maytag. I will be telling everyone who will listen to stay away from Whirlpool and Maytag, because their customer service sucks big time.

This Maytag Centennial with commercial technology washer has ruined a couple of thousand of dollars of clothing, maybe 10 to 12 of my favorite shirts (ripped holes around the top of the pockets), bath towels and sheets and comforters and hand knitted small blankets that can never be replaced. It tore holes in nearly everything that was made out of cotton, I was doing spring cleaning and I normally wash most of my summer clothing, but this time this washing machine destroyed nearly all my summer clothing. This washing machine came with the house I just purchased. (I gave my older Maytag washer and dryer to some needy folks which worked great when I moved here). Disappointed in MAYTAG. Will never buy another Maytag!

Washer does not clean very well, clothes are left with spots. The water level is never comparable to the clothes thats in the machine, it causes me to lose a lot of water as well as detergent. This machine is the worst washer we have owned. Its also very noisy.

Purchased a Maytag dishwasher (Model #MDB7749SAW1) in January of 2013, installed in February. A little over a year later the control panel went out. I called Maytag and they were kind enough to pay for the part and I had to pay for the service. Now it is July of 2015 and the control panel is going out again. I called Maytag directly and talked with a service representative and the best they could do for me was for $269.95 they would have it fixed and I would have a one year warranty as well. Based on the pattern the warranty is not going to help as it goes out just after a year. For only having it 2 1/2 years it is becoming a very expensive dishwasher. There should be a recall on this control panel. Very disappointed.

I bought a new refrigerator 6 weeks ago and it is not cooling or freezing anymore. I lost all my food. I spent 50 minutes on the phone to be told that the earliest they can fix it is in three days! Can you believe that? I will never buy a product from Maytag or Whirlpool again and everybody should be aware of the awful quality of their customer service!

I purchased a washer on 8/13/12. I had it installed on 8/20/12. It did not clean clothes properly. I went to Two Guys and they said they dont take returns and told me to call Maytag. I called Maytag and they sent a a service agent to check the machine on 9/10/12. They said the machine codes were imbalanced and over stud. They need to recalibrate the machine. I did laundry the same day and still find clothes do not come clean. I need to return the machine. I called Maytag and was told they dont take returns. This machine is not cleaning clothes as it should be and I want a refund!

Model MFT2776FE200 worst purchase of my life! We purchased the Maytag French Door Refrigerator last year. Within a few months, freezer failed and we had to have a retrofit done. Less than one year it has failed again. No refrig for over one month and still no parts. Hundreds of dollars of wasted food and I’m asked by Maytag Service if I have an extended Warranty. I didn’t realized that a new refrig needed to have an extended warranty. Will NEVER purchase another Maytag product again. We are devastated that spending 3k on a fridge means you might as well throw your money to the wind.

I purchased a topload washer two years ago and the plastic lid has been replaced 4 times because it cracks at the hinges. It is obviously a manufacturers defect that Maytag refuses to admit. They come up with excuses blaming the consumer instead of their bad design.

I purchased a new Maytag microwave from Lowes barely two years ago. The inner door frame is coming apart which makes the handle to open slack which means the microwave does not operate correctly because you have to open & close several times. I called Maytag. They said the one year warranty is over. Furthermore one of their authorize dealers want $200 for labor, parts is separate. I said I can purchase a new microwave for less which I intend to do but never MAYTAG again.

Our Maytag Bravos Quiet Series 300 is anything but quiet. Within two years of purchasing it, we now hear an F18 jet fighter taking off from our laundry room. Neighbors near and far come running to avoid getting injured when the spin cycle kicks into after burner. Seriously though, this looked to be a nice machine and operated flawlessly until a month ago when the spin cycle started sounding like a jet fighter taking off. I am handy and often fix appliances and things around the house. From reading reviews here on Consumer Affairs and other places, I am finding that the noise problems are more common than not. Investing $400+ into a replacement tub/bearing set would further support Whirlpool/Maytag and the sucking sound they make to get at my wallet. From what I have read, I am likely to have more problems after fixing this one (it will likely break again). I am going to quit while I am ahead and purchase a new washer. Whirlpool/Maytag will never see my business again. Its ludicrous to have an expensive appliance like a washer only last two years. BTW, I just spent $200 to replace the control panel on my 4-year old Maytag dishwasher. A cheap and horrible design. The part probably cost $10 to make. BOHICA. (bend over, here it comes again). FYI: Whirlpool owns and sells its products under several other appliance names. Names that include, Kenmore (yes, Sears), Maytag, KitchenAid, Jenn-Air, Amana, Gladiator GarageWorks, Inglis, Estate, Brastemp, Bauknecht and Consul (Wikipedia source). Like a Lotto Scratcher, peel the Whirlpool or Maytag name sticker off and underneath you will find the real name... CRAP! Its sad to think that you have to purchase products made in Korea to get quality. Very sad.

Tried various cycles and I hear water going in but don’t see any water. How does this wash clothes. I want to see water and soap clean the clothes. If I want dry cleaning I will bring the clothes to the dry cleaner. Never again will I buy a high efficiency washer. My clothes do not come out clean!

I am writing to tell you the dishwasher sold to my family malfunctioned as a result of an apparent design flaw. I also ended up wasting an entire day for a service person who never arrived. On October 14, 2009, my family bought a Maytag Dishwasher (model #MDBH979AWW) from Home Depot. It had run beautifully until last week, when the left-hand side of the control panel went dead. I then called the Maytag service number (800-688-9900) listed in the instruction manual and scheduled an appointment with the A&E Factory Service vendor for the following Friday (July 6th, 2012) between 8:00AM and 12:00PM. Around 12:30PM, no one had arrived, so I called again. I was told by the agent that the technician was en route and would arrive at my home in forty five minutes. At 2PM, still nobody arrived. I rang again when I was then informed that my name had been strangely kicked out of the system and made available for a reschedule. Wanting to stick with a Maytag-approved business, I went ahead and scheduled the next earliest appointment available, Monday, July 9, 2012. The technician from A&E Factory Service that actually did show up reported that the entire control panel had to be replaced at a cost of $281.48. Interestingly, he added that he had seen other Maytag dishwashers with this exact same problem and recommended that I wait until the water settled before adding extra dishes during a cycle since water apparently leaks into the electronics via a small gap on the top of the inside of the door. Of course, there is nothing in the instructions warning against such.I chose to fix the machine since I didnt have the money to purchase a new one. Are your dishwashers designed to last only a few years? I truly believe that I have been duped by Maytag since this problem resulted from a design flaw. I am asking you to please look into these matters and correct any wrongdoing that you see fit. Copies of receipts for the dishwasher purchase and service repair are enclosed.

Received this Maytag dishwasher model MDW7749SBW1 as a gift from my son in June 2013 when my old dishwasher finally quit. January 2014, the soap/rinse aid dispenser did not work. Called Maytag and they sent repairman who replaced the part. Still did not work so repairman said another part was not communicating with the dispenser so he replaced that part. Worked fine. No charge since it was under warranty. Now its July 2014 and the touch panel doesnt work. Called for repair and was told since it is out of warranty, it will cost about $350 to repair. I called Maytag about this and said that I had a defective appliance. I was told that since I didnt buy the extended warranty, there was nothing they could do. I mentioned my last Maytag lasted 25 years and had only two minor repairs so I didnt see any reason to buy an extended warranty. I thought I was buying a good product. I was told shed register my complaint. Waiting for my repairman to come out tomorrow and see what he can do. I also have a Maytag stove. Wonder how long that will last?

My dishwasher is 3-4 years old and the control panel is malfunctioning. Cant push a button to choose what cycle I want, it doesnt respond. I went to the Maytag website to see if there have been others with this problem. It appears that there are many other people having this problem. Parts are not available and it seems that Maytag wont do a recall on this product due to the control panel malfunctioning. I have been dealing with this problem for the past few months. I dont think Maytag is worth the money. They want if you only get a few years out of them.

Purchased a Maytag side by side MSB27C2XAM00 in June 2014 to replace a 20 year old Kenmore. After 14 months the fridge stopped keeping things cold in the food compartment and in the freezer. And, the water and ice dispensers stopped working. Called Maytag and they confirmed the fridge was 2 months past the warranty and the best they could do was offer an extended one-year warranty for $325 and set up an appointment. I declined and called a local repair company. They responded promptly and discovered the problem was a bad board. Had to replace the board at a cost of $475 (parts and labor). It was $150 more than the extended warranty but I was already in the hole for $100 service call and I was able to get the fridge repaired on the spot. I had the Kenmore for 20+ years without one repair. Maytag was good for one year and 2 months. Dont know how this company will last with a $2000 product that lasts a year. I can not recommend this product and advise anyone in the market for any appliance to avoid Maytag products.Updated on 11/20/2015: After the board was replaced, the fridge worked but was not keeping either of the side by side compartments cold. They were cool but not cold. Repairman returned. Said it was the compressor which needed to be repaired/replaced. Maytag said the compressor was under a 10 year warranty unlike the other parts of the fridge. Good news, Maytag covered the cost of the part / but bad news that it broke after 14 months of use. However, the service people told me the cost of the compressor was the smallest part of the repair. Labor and service would be costly and Id be better off getting a new fridge with a 5 year warranty contact. After I got over the initial shock of having to toss a 14 month old fridge that cost $1500 and complaining to Maytag, I went to Lowes and found a replacement fridge. This time it was not a Maytag. Moral of the story stay away from Maytag. Dont be fooled by the brand. Avoid them at all costs. And purchase a fridge with a 5yr+ warranty contact!

Maytag XL Washer - My new machine is awful as well. Black clothes are smeared with I dont know what... looks like dirt. The wrinkle cycle doesnt work and the bedding cycle forget. Wish I read reviews... silly me.

I share the complaints of others about the Maytag Bravos washer (model MVWB300WQO), which I purchased in October of 2009.Besides being overpriced, its a washer that doesnt soak clothes, develops a bad odor, has silly things like unnecessary lights and music, and you cant add an item once the wash cycle has begun without the cycle starting over from the beginning. It also leaves washed items in twisted wads and the lid locks so you cant see whats going on inside. In addition, it damages items. Ill have to replace a full-sized blanket that it recently destroyed and now I cant trust that itll wash things safely, which is a problem. The person I spoke with at the companys customer service department simply said that I shouldve used the bulky item option instead of the regular cycle. I explained that Id used the bulky item cycle before and the same thing happened. The washer leaves larger items stretched very tightly across the tub and I suspect that is how my lightweight cotton blanket was destroyed. She offered to schedule someone to service the washer. But its not broken, its a poor design, so sending someone here would be a waste of time.

I purchased a Maytag top-load washer 16 months ago. I had a problem with it four months after purchase and they told me it was not leveled, which I did not believe. I set it up as the manual said to. The washer left clothes soaking wet about every 30 loads. I continued to use it and the washer finally quit working after 16 months. The repairman found the nut which holds the pulley on the shaft that turns the drum had been loose and had been this way for some time. $129.00 later, it was fixed. It works fine now. I wonder if this problem should have been caught on the first service call when it was still under warranty.

I love this washer. You can fill all the way or energy setting but either way it does the job. I paid 1200 for a Whirlpool. it was broken within 6 moand couldnt get service repair. With the Maytag it was on sale for 550 cash. It stop spinning. I called for service. They were there in 2 days on time and 20 minutes it was working. It was a needle stopped it. Just reprogrammed and wa-lah!

I am about to replace the control panel on my Maytag dishwasher (MDB7749SAM1) for the second time since purchasing it in 2012. Additionally, I have replaced the door gasket twice, as it becomes loose and does not properly seal, causing water to leak from the door during the wash cycle. There are many documented complaints of corrosion on the control panel ribbon cable necessitating replacement of the entire unit. If there were a way to replace the ribbon cable instead of the entire panel, it might be a bit easier to swallow the repair expense. Either way, it is ridiculous to have to spend almost 1/3 the original cost of the dishwasher to make it usable again, and twice in only 5 years time! My previous dishwasher was 30 years old and still functioning (though noisily) when I replaced it with this expensive lemon. I have not contacted Maytag, as it is not in warranty, however, it seems that a major appliance should last longer than a couple of years without issues.

I have nothing but great reviews for my Maytag experience... In approx 1975 I purchased a Maytag W&D, Model MAH4000 MDE4000, when their advertisement was portraying Maytag repairmen as the loneliest repairmen. Maytag was so dependable that the repairman was NOT needed...and it was true... That Maytag W&D set lasted til approx 1998 when it was upgraded to the Maytag Neptune MAH4000 series... Had a minor problem with mold in the washer, but Sears and Maytag replaced the seal and made another modification... We also dried the seal at the end of the washing day and left the door slightly ajar between uses... Have not again had that problem.I have since given the Neptune set to my daughter and the washer and dryer are still in operation, WORKING SUPERBLY I might add... So I am searching for a good quality Model MAH4000 and MDE4000 to replace my current much older, yet functional Whirlpool... It may need some repairs and about a year ago, I spent $173 to replace the Pump which was clogged by a sock inadvertently stuffed around the top of the drum when too many items were pushed in at one time. I prefer not to throw additional money at this machine! So, if you know of a Quality pre-owned Maytag Neptune washer and dryer in the Lexington KY area, please contact me...

I have bought 2 high end top loader models (Maytag centennial commercial), brand new both from Home Depot. The problem is Maytag is making them cheaper! Suspension is coal springs that suspends the load so if you fill it up, it lowers the drum to the floor, instead of a bottom bracket that supports the weight from lowering the drum to the floor! Second is the pulley system with the belt drive that wears through the plastic casing. You know some people dont have $900 or $1,000 for a machines that says commercial or heavy duty that only last 4 years when you have a family of six! Very very sad, will never buy another Maytag.

Called about our upteenth issue with our Maytag microwave. Was told the part was covered but we would have to pay for service. The last tech told us how to wiggle the part to make it work. Paid a fortune and it broke again. They do not care about customers!!

I was always impressed with the front loading spin washers commonly found in laundromats. The top loading Maytag Bravos does a great job of cleaning clothes and does not stick another door in your way when loading or unloading it.

2 weeks after my warranty is up, the control panel is shot. They used to make quality products and that is why I purchased a Maytag. I had before this a very cheap dishwasher from G.E. and it lasted 9 yrs. I cant believe it is already broken. Do not buy Maytag!!

We had a house built in 2007 and bought all new Maytag appliances - washer, dryer, oven/range, dishwasher, refrigerator and microwave. Consequently, we spent many thousands of $ and Maytag made much money from our purchases. In the 7.5 years since we have been using these appliances, the dishwasher already had to be replaced, as fixing it would have cost just as much as buying a new one. But its the range that I am so angry about. I have replaced the igniter 3 times since 2007, and last night, it went out again. I have spent $494 so far to keep replacing the igniter and once I make the service call to replace it AGAIN, it means I will have spent approx. $700 to keep fixing an appliance that is only 7.5 years old. Maytag says the warranty on the appliance is only for 1 year and will not budge on giving me a break on cost of parts and/or service. I will NEVER AGAIN purchase anything Maytag or recommend Maytag to anyone.

Purchased the Maytag Bravos washer from Home Depot in August of 2011. Today it caught on fire (Sept, 2014). Had problems with it from the start. Some of the issues include the washing machine constantly getting off balance even with small loads, not completely draining the water from clothes resulting in having to run additional spin and drain cycles, and a bad odor coming from the water that stays on the clothes (we even called a plumber thinking it was something with our plumbing). Well today was the best. I started a small load (one twin flat sheet and a pillow case) and about 10 minutes later I smelled a weird burning odor coming from the laundry room. When I opened the door to the room it was filled with smoke. The washer was the only appliance running, otherwise I would have assumed the dryer was the source of the smoke. When I opened the lid to the washer, smoke started pouring out from around the inside drum of the washer. It smelled like burned rubber and ash. Needless to say, I doubt this washer is worth repairing. We actually have had repairs on it previously (twice in the first year) and its just a piece of junk. Glad I was home when the washer caught on fire. I hate to think what would have happened if I had not been able to unplug it and it continued burning. Do Not Buy This Brand. Definitely do not run this washing machine unless you are home to monitor it. Maytag Bravos is a fire risk!!!

I purchased a Maytag dishwasher (Model No. MDB8949SBWO) in September of 2013. Within the first year (and under warranty) the control module failed. The dishwasher is now almost two years old and the second control module has failed. From other postings it is obvious that Maytag has a known defect in their control units. To replace control modules on an annual basis makes this an extremely expensive dishwasher to own.

Since day one, no matter the size of the load or how careful I place the clothes or what level or water, washer vibrates and moves around the floor. I have had service out twice to recheck level but it still vibrates. Worst washer ever. I should have spent the money to repair my 20-year-old Kenmore.

This review is for a Maytag Gemini MGT8775XW 30 Freestanding Double-Oven Gas Range w/ 5 Burners. I cannot believe the amount of problems I have had from this $2000+ range. Within just a few weeks of getting it, the paint started scratching off the surfaces nearest the heat. Then, the plastic cover over the digital display and controls bubbled up due to the heat of the broiler being in use. They designed it so that the heat escapes from the oven right in front of the control panel, so when you want to adjust temperatures on the control panel, you chance getting burnt from the hot air every time.The very worst design are the manual knobs for the burners on the front. They are at an angle, and if you look at the oven straight on, you see they are higher than the burner surface. A hot pan that overhangs the burner cooks the knobs. The plastic interior of the knob lacks any kind of heat resistance and actually starts to turn soft, keeping you from being able to turn off the burner at all!Most dangerous of all, the knobs are frighteningly easy to bump, pouring gas into your house. We have had this problem multiple times. Today, my dog must have wanted to investigate the top of the stove, because when I came home, the burner was on, had burnt through a pot on the stove, and was just at the ignition point for an item sitting next to the stove. If I had come home 15 minutes later, my house would be in flames right now. I am having to air out my home as I type this. I am DONE with this dangerous oven and will be shopping for a new one, and it certainly wont be Maytag.

RE: 5.2 CU Ft Top Load Washer, Model # MVWB865GW0, Serial # C84370937 - Purchased Jan 2019. The clothes come out terribly tangled and severely wrinkled, even when using the Wrinkle Control or Delicate cycle and occurs in every load size. Ive tried every cycle, including the deep fill and low spin speed but items are so wrinkled that whether I lay flat or hang or put them in the dryer, I have to iron them, which I never did before.

The oven range (model number mgr8772wb) will not heat to proper temperature. It runs 35 degrees cold even after the built-in adjustment of 30 degrees. the repairman said it was just a cold-natured oven and we had to get used to it. So if a recipe calls for 400 degrees, you must preheat to 430 degrees. As much as this thing cost, it should cook properly. I must rethink Maytags reputation. I thought they were the best. Wrong.

I have a Maytag Washer and Dryer that I am very happy with. I have had both of them for about 6 years. I had a problem with the soap dispenser not working properly shortly after I purchased them, but a service technician came and fixed that within a few day. I will probably stick with the same brand when/if I do have to replace them.

Problem with the front panel are the dishwasher has been replaced 2 times in 3 months. Was told by the tech repair person is not a well made product. He would replace it if he could had a warranty and added a new warranty for 1 year and is up again and of course have to do it. Was told if it happens again they most likely replace with a new unit. Hopefully. Not happy.

We bought a Maytag refrigerator Model # MBF 2254HEW, Serial # 14560744NG. It worked for 7 years and now its dead. Well it does blow warm air. We are told it cost so much to fix one that we would be better off to buy new. I bought an extended warranty but of course all is out of warranty and Maytag is sorry for the inconvenience and that parts do fail. I am going back to using the old style refrigerators that last rather than paying an enormous amount of money to buy something new and looks nice but will only last a few years. When is a recall in order? When are companies required to do better for the customer? We are told that the compressor might be OK but it could be low on coolant but it is very difficult to find a leak.

I purchased Maytag washer/dryer set in Feb 2021. In June the washer broke. It took 2 weeks to get repair person to look at it. During the appt no faulty product was identified so they dont know what to replace. No parts were available. A follow-up appt was set for 1 month later. No parts are available to make the repair so a follow-up appt would be futile. . The only communications other than No Parts is that they want me to purchased an extended warranty. I will never purchase another Maytag product or recommend them to anyone. Meanwhile my warranty continues to time-out and they dont have any parts or idea when they will be available. Im not sure how a company can sell products that they do not have some level of support for those products. Beware of purchasing Maytag Products.

I, like SO many other people, am experiencing problems with a relatively new Maytag dishwasher. Mine is Model MDBH979SAB1. I have owned the dishwasher for 4 years but use it 6 months of the year and, because I live alone, maybe twice a week. In effect, it has the equivalent of less than a year of normal use. My problem is the same as countless other people. I can tell from how it behaves that it needs a new control board. I find little comfort in the fact that I one of several thousand people experiencing a problem with a newer Maytag appliance. What concerns me, after reading many negative reviews and seeing Maytags response, is that Maytag does not seem to care. We need to get the word out. We need a massive boycott of Maytag. We need to hit them where it hurts: in their bottom line. Since they seem to be content to continue to put out defective products, the only way to protect consumers is to put Maytag out of business.

Bought a Maytag refrigerator/freezer 18 months ago. The freezer went bad. The first repair guy said it needed a new computer board which wasnt covered. Called Maytag, they wanted another repair service to look at it. He said it needed a new evaporator. We have now spent $250 to be told the repair will cost another $500. Maytag will make a goodwill gesture because we are a nonprofit business to cover the part only so we will still be out another $300. This is unacceptable for a relatively new Maytag. Obviously they can no longer be counted on to back their equipment. Very disappointing.

I have had this washer just a little over a year and the sensor panel went out... For $600.00 it should not break right after the warranty goes out. Buyer Beware.

Brand new washing machine model MHW8200FW purchased at Karls, a Ferguson subsidiary, in Madison, NJ end of June, 2017. I wanted to buy a top of the line machine and this is what the sales person recommended to me. Problems started soon after purchase. Initially I contacted Maytag because the machine wouldnt spin dry a cotton bath mat weighing 4.5lbs soaking wet. I was told I should put more items in the machine to help balance it. Well there WERE more items and the machine wouldnt spin dry them either. I tried every trouble shooting Maytag suggested. Having exhausted my nerves, I called for service. The technician came and said these machines are extremely sensitive and that sometimes they wont even run an empty cycle. He said this is a common complaint with these units. One of his suggestions was to take bath mats, duvets, comforters... articles like that to a laundromat.I did less than 10 wash cycles after his visit when the washer started having more issues and finally broke down completely. The technician who came this time wrote a repair order indicating a mechanical (Stator) AND electrical (Control Panel) breakdown ($500+ for the parts alone if the unit wasnt under warranty). He also stated that he had never seen such problems in a brand new machine.I contacted Maytag for an exchange. Maytag customer service wrote to me that the breakdowns are ... normal, with all the units we sell some may have a defect in the first couple of months... and refused to exchange my defective unit. I can accept that there may be a defect that will warrant a repair, but in this case there are multiple defects in separate systems - mechanical and electrical - within the first month of service. This shouldnt warrant any further discussion, only a quick replacement and an apology.

My wife and I purchased new Maytag dishwasher in 2011. Worked well for 9 months and then control panel went out. We bought a Sears with 1 year warranty. Sears fixed but then 2 more repairs followed with blown fuse and pump motor went out. We knew this was a lemon so we purchased an extended 3-year warranty through Maytag. Well the unit only works for a month or two then we are constantly calling for repairs. We just had the pump replaced a 3rd time and yep you guessed it the unit is loud again so here comes repair 15. The warranty contract states that if the same part fails 3 times, Maytag will replace the unit new one time and voids any further repairs. My wife and I are very frustrated and lost all confidence with the Maytag company. Our old one lasted 14 years and this new one is a piece of junk. The company reviewed my request of unit replacement but was denied for whatever stupid reason. This unit has over 5000 dollars worth of repairs not counting the lost time of appointments waiting for the repair. My wife has had to stay home and wait for 4 to 8 hours an appointment. She has many other obligations to do with her time. Its sad that Maytag does not stand behind their product. Its my conclusion that this company does not want to sell good product, they only want to sell extended warranties. Your products are not reliable if you have to offer warranties. I would like to see if I can get to repair 30 before my warranty expires by March of 2015. Maybe I could then see if 30 repairs would make the Guinness Book of Records on the most repairs done on a dishwasher with extended warranty. That would be something the company could be proud of dont ya think.

I purchased a Maytag Gemini April 22 2017 and I am very unhappy with it. The ovens are not working properly. I have thrown away so much food because the ovens won’t hold temperature. The display says it’s the temp. I set it but the temp keeps dropping and rising causing the bottom and top to burn and inside not to cook. Both ovens are doing it. Had a repairman come day before Christmas. He said there is nothing wrong. He said set temp, when preheat beep goes off wait 15 minutes for it to cycle then insert food. I tried this Christmas Day. Oven is still not working and again I threw away more food. I am so disappointed in Maytag. Serviceman is set up again to come out next week. I think I got a lemon. Please. I think they should replace the whole range. It’s not fair. I paid so much for this range and can’t use it.

My refrigerator stopped working less than two weeks after purchase. The ice maker failed to produce ice. I feel they sold me a lemon. Yes, I do!

Purchased a maytag washer last yr. and I feel it is the worst washer I have ever dealt with. I hate that every time I wash somethings they come out with lint all over them and they are the same things I have washed before and never had the problem, plus I hate the cover locks so you cant put water in before you put soap in.

Maytag Bravo Washer - I recently purchase a fairly expensive washer built by Maytag. In my opinion it is the worst washing machine I have ever owned. Again in my opinion their advertising about being such a reliable company should be considered false advertising, and near criminal. If you had a lower rating I would use it. Absolutely you should never use the word Bravo in a description of this washer. I will never purchase a Maytag appliance again. Check the internet for reviews before you purchase. I had just came out of surgery and in a wheelchair and trying to move back home and didnt do my homework.

The engineers at Maytag saved a few pennies by only using one thermistor for temperature control. It is in the box. There is nothing monitoring the temperature in the freezer. If you put your fridge in the garage where the temp is 40 degrees, the motor will never come on, and your frozen foods will melt! In my new MRT118FFFZ01 unit, the temperature in the box varies by plus or minus 3 degrees F, but the freezer varies from minus1 1 to plus 25 degrees F. 36 degrees difference! Lousy design. Have had two service calls, and they both said that this was the way it was designed and there is no fix for it.

We bought a Maytag dishwasher (Model: MDBH979AWS3) in January 2010. In April 2012, the control panel stopped working. A local repairman came out to see it for $160, diagnosed it, and suggested that we call Maytag to see if they would give us the part because it was only a two-year old machine. He did say that the control panel was not a part that was troublesome!Maytag offered an extended warranty for only $287 that would cover the part! The total repair cost was almost equal to the cost of a new machine. Home Depot, when consulted, acted as if they know nothing. After reading about other peoples experiences with this company, I feel that it is no longer an honorable company standing behind its products. In fact, the whole repair process is set up to rip off the consumer.We will now look to purchase the best and cheapest non-Maytag product, not from Home Depot, and throw it away when it gives out, which more than likely will be soon. These companies have finally convinced me to do what I am sure what they have always wanted every consumer to do. Throw it away when it breaks down.

I paid over $600.00 for a new maytag washing machine two years ago. It quit working a few days ago and the man said itll cost over $400.00 to fix it. Why do you people build this type of junk? I would like to hear from someone on this and why I had to pay $300.00 a year for a washer that is totally worthless now??????? ** please contact me. This is crazy to buy this washer and it only last two years.

The engineering of all these new machines are totally useless. Bring back the old tech. They DRY wash, NO WATER, they take forever to finish, wasting energy, clothing not cleaned. They are very noisy, doing nothing. Time to recall all of these units. They are totally useless.

I purchased MVWB955FW (washer) and MEDB955FW (dryer) from AJ Madison and the units were delivered in December 2017. After using the washing machine 5 times the glass lid spontaneously shattered putting glass into the machine and all of the clothes. I called Maytag for a replacement/service and they had to reschedule as the lid wasnt in yet. A week later, I followed up with Customer Service only to find out that the replacement lid was also shattered. They didnt make a replacement lid without glass (not sure why you need to watch the clothes being washed). I was told that there were no replacement lids available anywhere. I asked about getting a replacement washer and was told couldnt do that.I asked them to pick up the units and refund my money, which they promised. It is now 2 months since the original call for service and I continue to have to follow-up with them (never get a call back) and STILL have the broken units in my house. I have since purchased a replacement set (LG) and waiting for my refund. I will NEVER do business with Maytag/Whirlpool again.

Maytag, Whirlpool, and Sears are junk dealers. We bought a Maytag Bravo topload washer in April 2011. Shortly after the first year, after using it once weekly, it began to stop draining. Clothes were soaked, meaning lots of wringing out by hand and using the dryer double time to get them dry. There are no clogs or kinks in the line. The machine is junk! It should have lasted much longer than this. I am not going to spend more money to have a repair person come and check on it. Its not worth it. Im going to buy a GE washer, the old-fashioned kind that gets clothes clean. Maytag, Whirlpool, and Sears are much worse-off breeds these days. They are off the list for good. Their products are a joke. Unfortunately, Im not laughing, but close to tears. Enjoy my money, you **.

Purchased Maytag Bravo High Capacity Top Loader Washer in 2011. Purchased at Lowes. They were great. I did not get the product warranty. Wish I did. At first seemed great. Washed comforters and clothes come clean. It does always get off balance and takes a while to wash the clothes. Well I am on my 4th time having it repaired. Put over 400 into it. Now it is leaking. Going to cost another 300 to fix. Only going on 6 yrs old so done. Just ordered a new washer LG Top Loader with warranty praying I have better luck with this washer. Just wanted let you know I had no luck really. Thought Maytag was a better product. Sad to say not for me???

We purchased a Maytag Dryer with the lint vent on top on March 21, 2014 from ABC Warehouse in Ann Arbor, MI. Whoever engineered this does not dry clothes. Trust me, this will be the last Maytag I buy. There is lint seeping out of the top and when you clean it the lint gets all over the place therefore, my laundry room is always full of dust.

This range and oven get unsafe, very hot on the surface and sides. Also, first time we used the oven, our oven mitts and bbq tools caught fire in the storage drawer.

My complaint sounds just like the others listed here. Purchased Maytag dishwasher MDBH979SAB1 at Home Depot 2/2013. In June 2014, the control panel started to malfunction. When I called Maytag, these were the options given: 1--have it serviced out of warranty at $89-$150 for repairmans trip & diagnostic, which doesnt include parts & labor or 2--obtain something called Repair plus one, which covers the cost of repair and reinstates the warranty for one year at the low cost of $264.95. So either way, Im going to have to pay almost 1/2 of the original purchase price. Ridiculous! We had our previous dishwasher (not a Maytag) for over 13 years, with only minor repairs. We purchased a Maytag because we thought it was a reputable company that stands behind their products---well dont believe it! I would NEVER recommend any of their products.

Purchased my Maytag Dishwasher MDB7749SBM on 5/13. 3 weeks ago the panel went out! I found others have had the same complaint on their Maytag Dishwashers too! I also learned this model was discontinued from Home Depot. Is this because Maytag knows this Dishwasher was JUNK and that they allowed consumers to buy this model knowing it had these problems - I believe so! I find it absolutely crazy that Maytag has not issued a RECALL and now I am out almost $700 plus if I get it fixed or buy a new one, I am out even more $$! There has to be some RESPONSIBILITY taken from Maytag!!! This Company was built on an excellent reputation but now this company reputation is considered POOR for selling defective products and doing nothing about it!

Dishwasher is around two-three years old and it will not start or drain. From what I can tell on the internet, this touch-pad control panel has been an ongoing problem for Maytag. Will try to fix myself, and if I cant fix it, I will buy a new dishwasher but not a Maytag. By the way, my washer and dryer both went out this year - five years old and both are Maytags. Stay away from this brand.

I have a gas dryer from Maytag that works very well. Very easy to use and economical using it with propane. Im pleased with my purchase. Ive had it now for about 8 months. I would recommend buying another one.

OK, LAWYERS -- Where are you?!! You have a lot of very unhappy people who feel they have been justifiably TAKEN! Whirlpool needs to replace these refrigerators with another brand! We bought same bottom freezer Maytag refrigerator in 2010. Luckily, which we dont usually do, we purchased a five year warranty plan. Within six months we noticed the rubber seal on our refrigerator on the french door part was turning yellow and then getting darker. We feared something was burning the rubber. A Maytag repairman looked at it, called Whirlpool, told them that there werent enough parts to fix this refrigerator. Whirlpool asked him what they should do and he told him it should be taken out on the front lawn and burned (yeah for that repairman)!! Whirlpool agreed to replace the refrigerator with one, very similar but a new model #. Thank heavens, after our insistence, the warranty was extended to the new one. Now after about three years, we are having the same problems that all of you are having with the next one.. Our Home Owners insurance adjuster just gave us a settlement to have all the ceramic tiles removed, which are cracked in almost two dozen places, and whole floor replaced (minus our $1,000 deductible). The floor was put in new three years ago. The refrigerator repairman is next to come out. From what I have just read about all the complaints on this refrigerator, NOTHING is going to fix this problem short of replacing it at our expense. My advise to everyone --- FIGHT THIS. Write to Whirlpool (not Maytag -- Whirlpool owns it), and blast them over and over with letters and complaints and threats of lawsuits. Why should we be taken for that amount of money while Whirlpool does nothing but keep it. A class action suit is badly needed. Big corporations should not be able to take people over like this and get away with it. If it takes a lawyer willing to take on a class action suit, this is it! In the meantime, bombard Whirlpool with letters and dont stop! It takes persistence, but in the end -- most of the time, we will prevail. Big companies hope we will give up and go away. They count on it. Dont let them win!!! I have had a Maytag washer and dryer for twenty years with no problems. Problem is that Maytag doesnt exist anymore -- who is making this....?

Im so mad over my new purchase on the XL Bravo washer and dryer and Home Depot will not return. I have 3 kids and a hard working husband. My clothes do not come out clean no matter what cycle I use. It takes forever just to wash one load. If you spill something on your clothes and it dries crusty it will come out of the washer crusty. I want to cry. So much money wasted and cant get our money back. Would never recommend a washer without an agitator. Towels come out soaking wet, and dont spin dry if heavy...forget washing a blanket. 4th day using the dryer and now there is no heat. What was I thinking!! So mad and sad too!