Washer needs new transmission at only 3 years old! Maytags 10 year part replacement doesnt cover it. The company actually asked why I didnt purchase extended warranty, I thought I didnt need one. Bad bearings, it doesnt wash the clothes clean, $400 to fix it. Needless to say Im buying a new washer and it will not be a Maytag, worthless piece of scrap!

Just got a Bravos Maytag commercial washer. Washed two throw blankets and the washer has a see-through window on top, and I could see that the blankets didnt move on top. How are clothes supposed to get clean if they dont move? It also took an hour and a half for one load. What you are saving on water you are wasting on electricity. I personally dont like them for those reasons. I appreciate the company in my town (little known), they let me return and get the old agitator type with NO sensors. Just love the agitator, might wear on clothes a little more but at least I know theyre clean!

I take pride in my cooking and love my kitchen. As you know this is where everyone gathers when you are entertaining. The Aqualift system does not work. I have run the process 3 to 4 times consecutively in row and the inside oven the oven is never clean. I wipe out the sides over and over. So disappointed. The only saving feature is that you can not see into the horrible look of the inside the oven when it is closed. Was this feature really tested before it went to market????

We purchased the Bravos X washing machine on Feb. 9, 2012. I had a Maytag for 30 years before this one and did not have any problems. My model # is MVWX700X. I have given it sufficient time to get used to it. I have tried all cycles for my whites and am not satisfied. I use Clorox in the receptacle and I have only used Tide HE. I spot treat all of our underwear, which is changed every day, and it always comes out unacceptable. I am so disappointed since I was so fond of my old one and only thought I wanted another Maytag. At this point, I would never recommend this machine.

Disturbing that this product made it into production. I have the matching dryer too, and its just as bad. First the washer rolls up clothes into a tight ball better than I could do if I did it by hand. Then it spins, setting the wrinkles in thoroughly. Then, even though I shake out the clothes before putting in dryer, after the clothes come out of the dryer (without letting them sit in there) - the clothes look like someone drove over them with a car while they were rolled up in a ball. Bonus: the clothes dont even get dried. Ive watched the clothes in the dryer, the drum is designed so the clothes stick to the outside of it and go around, they never actually tumble or get any air circulation. What a disastrous product.

Maytag Bravo Washer - I recently purchase a fairly expensive washer built by Maytag. In my opinion it is the worst washing machine I have ever owned. Again in my opinion their advertising about being such a reliable company should be considered false advertising, and near criminal. If you had a lower rating I would use it. Absolutely you should never use the word Bravo in a description of this washer. I will never purchase a Maytag appliance again. Check the internet for reviews before you purchase. I had just came out of surgery and in a wheelchair and trying to move back home and didnt do my homework.

Washer gets out off balance too easily. If I put in a couple of towels, it will almost invariably stop part way through the wash cycle. I was told you have a great washer! Its the last of the two-belt Maytags! My reaction: so what?

I bought a Maytag washer expecting To get the best and have already had Service on it three times and it still isn’t working. I have spent a fortune at the Laundromat when I have a 4 month old washing machine at home and not getting anywhere with getting anything back on this. I am very disappointed in this Washing Machine.

Since the day I bought the Maytag Bravos XL washer it never worked correctly. An entire year of several repair men, which half said there was something wrong and other half said nothing was wrong with it. Now it sits in my garage as the most expensive paperweight. After repeated requests, the Whirlpool company that owns Maytag now refuses to stand by their product, replace it, refund it or anything at all. They have washed their hands, yet I cannot wash my clothes in it!

Bought Maytag dishwasher 2007 at Lowes. Model mdbtt60aww-37837606ll manufactured in Benton harbor, Michigan. First got a recall that something was faulty, could cause fire, needed replacement. Took 2/3 weeks to get repaired. So couldnt use. Never quite cleaned good - many times had to rewash silverware, glasses. Never took off food unless very well rinsed. Today the control panel went. Called a local repair he said, Dont even fix. Toss and get a new one because its too costly to repair. I asked what should I get. He said no GE, they are getting out of appliances, no Samsung. Hes got whirlpool so guess Ill give that a try. In the past Ive had dishwashers 20 years, appliances 20 years. This junk lasts a year or two. Plastic cracks. None of these appliances are great anymore. Doesnt matter who you buy. Someone needs to get some quality control on what these companies are peddling .

Internet stated refrigerators should last a minimum of 13 yrs and up. Mine is less than 5 yrs. old, a Maytag 25 cu. ft. French Door Bottom Mount Ref. with freezer on the bottom (MFF2558VEW). Had to replace upper gasket in less than 1 yr. of purchase and needs another now (not affecting the sealing aspect on doors, more aesthetic on upper door thin flap that tears easily).Drain plug & configuration for drain was a known manufacturers defect, but cost me money to replace as 3 yr. extended warranty expired. Lower gasket had to be replaced in yr. 4 of ownership, bottom of freezer was producing a sheet of ice that needed removal every week. Normal settings is #3 for both top and bottom, worked fine for 4 yrs at this setting.Last month irregular cooling started to occur- top down to 52 degrees and bottom freezer below -20 degrees - ice cream hard as rock, have to defrost each time in microwave. Maytag repairman said could find nothing wrong, but try emptying entire contents and unplug for 24 hrs. I could hear pieces of ice melting and dropping throughout the evening. Next morning towels I had put around frig were saturated with water. Restarted frig after 24 hrs. and was working fine for 5 wks.This week same exact problem returned so I did the same thing only this time I had to go out and buy a small chest freezer as I had a full one in my Maytag and no place to put frozen food. It is nearing 24 hrs. and no water has appeared on the floor nor did I hear any ice melting and dropping - so dont know what to do. Will call repair man again and see what he suggests. As soon as I can afford another $1400 frig (this was on sale for $1,002 after discounts, but I will buy a less expensive one this time) I will purchase another brand with NO French doors and no bottom freezer. I loved my frig the first 3 yrs. under warranty, but now causing me too much physical problems having to empty and restock frig for repairs. I have a Tappan Frigidaire in the garage that is from 1998 - I bought from a neighbor who was moving and it has been working fine for 16 yrs. with no repairs. They dont make them like they used to!

We bought a new top of the line Maytag MGD7000XW dryer about 2 years ago. It worked great for about 6 months, thing started acting funny. All of the front console lights stay on all of the time and it ONLY dries on high heat now. This all happened after the warranty period. So fine, I was going to buy a new complete front console (CONSOLE Part Number: W10388467 $300.) as the online repairman suggested. Guess what, Maytag no longer offers the part to fix my dryer. So now I have a 2 year old top of the line P.O.S. MAYTAG dryer that cant be fixed. I will never buy from this company again (Maytag).

All in all I have liked my electric range, but I have 2 issues that I am having trouble resolving. I bought the range in 2003 and to find the model number I have to pull the range out from the cupboards on each side which would be extremely difficult under the circumstances. The reason I want to get the model number is so that I might find replacement parts for the doors edging that has flaked and rusted and is quite unattractive.

Ice maker not making ice, lights on the temperature controller are all flashing, ice/water dispenser door continuously opens and closes, refrigerator and freezer both do not cool/freeze properly. I purchased a new main control and low voltage board at a total cost of $400 and replaced them to no avail. Nothing changed when electronic boards were replaced.

I had a Maytag washer and dryer for over 25 years. I loved them so I replaced them with the Maytag name. They are not the same company as far as pride and product workmanship.From the get go it always had a dirty odor to the tub, as though the clothes had been left in it for days. I was told to just run through a cycle with bleach, but nothing. There is no lint collector and after about 8 years of using this washer, the old lint is in the bottom of my washer after every wash. Now, I have to deal with the thing coming to a screeching stop, not spinning out the water after the wash cycle. Sometimes it’s full of water and other times some water drained, but the clothes are full of water and not spun out.Now tonight, I went downstairs and found water on the floor, it’s leaking. My question is to call and get it repaired or not waste my money and go buy another brand. I may go with the latter.I purchased a fridge and dryer at Home Depot a few years ago. I wanted to stay away from Maytag name. I purchased another name only to find out it is part of Maytag. No wonder I’m having trouble with my fridge, making ghost-like howling sounds so loud it consumes the entire house. So annoying. Stay away from Maytag. They are not the same reliable, take-pride-in-work company.

I bought a Maytag Neptune washer and dryer set in 2001. I had horrible mold issues with the washer not long after, and the colors washing setting cant be used without the clothes coming out with a smell that implies they were not cleaned. The dryer lasted about a year longer, before it stopped heating the air and also would not stop running. I will never buy from Maytag again! Much the same as many other consumers have commented, I would give it less than one star if that is an option!

My husband and I purchase both Maytag Washer and Dryer 7 month ago 2017, because we have purchase Maytag washer before and were very happy with it. But this new Washer does not clean clothes at all, it is worthless. We will not purchase another Maytag Washer again.

In 2013, $1850.00 I purchased a Maytag double oven, $700.00 Maytag dishwasher, and a Maytag refrigerator for $2200.00. I have had nothing but problems with all of them.... The oven locked up on me had to call a repairman to fix it. Ive had to replace the control panel on the dishwasher... And the refrigerator!! (WHAT A NIGHTMARE) In 2013 just received the appliance they had to install a heater in the ice maker because there was condensation. 2014, Refrigerator dead.. Repairman had to replace interface and control board.. 2017, Icemaker crashes and had to be replaced... 2020, Now here we are again Ice maker crashed again! (JUNK). My wife told me that she has had nothing but good luck with Maytag appliances... Never again.

Bravo XL washer and dryer - I had the washer approx 2 months before it leaked water all over the laundry room. The company replaced the washer after two weeks. Now the dryer has gone out after two years. If it cost me the amount stated by other consumers I wont be fixing it.

I wish that I had looked up reviews before purchasing my washer 6 months ago! No matter which setting I use, the washer never fills up with enough water!! I have pulled clothes out that havent even gotten wet, due to not enough water in machine! All due to the government regulated water levels on the sensors!!!! So, I had my plumber put in hot and cold water faucets, then he put a short Y hose on, so this way I can add water to the machine.... The only thing is, you have to wait for the machine to fill with what it thinks is enough water to get your load clean.... stop the washer, then add the water you need. But if it reaches a certain point, it will automatically start draining. So you have to watch and make sure you stop adding the water, before reaching that point!

On May 23rd 2009, I bought a Maytag Dishwasher and paid $360 for it. Within the first year, the circuit board had to be replaced, then one year later, the same thing. On October 8th 2011, it appears that the same thing needs to be done. I spoke with the customer service and they will not pay for it. Clearly, this dishwasher has a history of being unreliable and should be covered or replaced. The internet is full of complaints against Maytag for this very same model. How is it that they have not reacted or invoked a recall? I had a similar incident two years earlier with a Whirlpool dishwasher; it turns out that they are the same company. I will never buy their product again!

After two years of light use of Maytag Washer 300 Series (MHWE300VW13), it stopped working. I bought Maytag Repair Plan Plus One on Oct. 8, 2012. I scheduled a service appointment on the 9th of October and was told the broken part needed to be backordered and that I should get the parts on November 5th. I have waited for almost one month. Today is November 6th and I received an email and was told I will have to wait another month! Am I in America? There are so many complaints about Maytag washers online. Can the consumer be protected? Am I complaining to the air here?!

Dishwasher has been very dependable. Very reasonably priced and in over six years of service never had an issue with it. It’s a little on the small side for a large family but if you’re for less in your household-- works perfect.

I purchased my Maytag side by side refrigerator 11/2011 and by 3/2012 the compressor went out flooding my pool house floor. Maytag replaced the entire fridge because I was only a few months old. I bought the 2 year extended warranty, went down to the pool house (which has central heat and air) and the compressor has gone out again! The results leaving my baseboards molded! My warranty went out 3/17/2015 and Maytag is helping NONE! The only thing they have to say is you can buy a new repair one warranty for $363 to repair for one year. I have had this refrigerator for 3.5 years and now this is the second time its gone out! Customer service said, pool house is different than a regular kitchen. I told her that the pool house is 1,000 sq heated/cooled kitchen, bathroom, sitting room. Thats no different than some houses. Why would that make a difference?? My parents have a 30 year old fridge on the back porch thats still running! I will NEVER purchase another MAYTAG product! Stainless side by side with ice maker.

If I could give this a 0-Star rating, I would! I cant believe Maytag would make such an awful washing machine! Within the first 2 weeks I called their service department because (in my opinion) the washer wasnt washing properly. It took over a month and several calls to get someone out to look at the washer & dryer. According to the technician, both machines were operating properly. Apparently the washer is designed to destroy clothing and bedding! The gentle cycle set on deep fill will add just enough water to get the clothing wet, then agitates for about 10 minutes, then it fills up, agitates for 3 more minutes and drains. During the 10 minute dry-run, I watch my clothes get destroyed! I have never seen anything like this! My sweaters are shredded, my tops are pilled up & in a garment bag this thing managed to destroy a sports bra! This machine has ripped my mattress cover in several places and pulled my sheets from excessive rubbing due to not enough water. And what is up with the slow fill? The technician informed me that the trickling water is also normal. If I could return this washer, I would! I will never buy another Maytag because my Bravos washer died after only 4 years, and this one is brutal!

Worst Washer ever...hated it from day one of receiving it (but couldnt return because moving into new place, took awhile to get it installed, and by then the 30 day return window had lapsed, so now stuck with this piece of garbage!). Is ALWAYS off balance whenever you wash anything of weight (i.e.: towels, sheets, blankets etc.). It takes me close to 2 hrs to get these items washed because I have to keep starting and stopping it to try to get it to spin dry because it ALWAYS throws the items so is off bal. and wont spin. Then when you hit pause, adj. bal., & start it again, it starts REWASHING the items (instead of continuing on from where you left off), and sometimes when it cant balance in the spinning cycle it just shuts down making you think the full cycle is complete, only to open up the lid to find your clothes all sopping wet. Also, NONE of the cycles will get any of my clothes clean...it just uses so little water your clothes come out feeling grungy and still dirty. I have had to resort to ONLY using the BULKY cycle because it is the ONLY cycle that will use a higher water level (mainly because bulky items like towels will absorb the water so it needs to add more). With this cycle at least my clothes dont FEEL dirty when they are done washing!There is no way of knowing how much time is left on any of the cycles, which is a real problem when you have to start and stop it, because you really have no idea how far back it goes to start itself up all over again. There is just no way to time it, because it keeps messing up where you have to keep stopping/starting it, and then you have no idea of time frame. Never saw a machine built so UNUSER friendly!I will NEVER buy a MAYTAG washer again, and NEVER will I buy a washer unless it HAS the center agitator, and a control for water level. These HE washers are the worst, and unfortunately they are now the only washers being made, but without water, clothes just DO NOT ever get clean anymore no matter which fancy and expensive detergent you use. HE washers are HORRIFIC. I may just buy an old style used washer with the agitator... at least I wont be wasting energy to only wind up with STILL dirty clothes when using HE washers! FINAL NOTE: AVOID Maytag HE Washers at ALL COST! You will be sorry if you decide to purchase one!

I read the reviews before I bought this washer, went to a major department store to buy it. This way I knew that I could get good support if something happened to it. Its been 3 months, I use the washer everyday. There are 4 adults in my building, they use it daily. I have never had a problem yet, the clothes come out cleaner than the front loader I have. It seems Maytag still makes a good product. I am the first to admit, when you make large number of products you will have some with a defect. But this washer the Centennial by Maytag works great.. Plenty of water in the tub, the clothes come out clean.. Maybe those people having problems need to stop buy at big box home centers. Theyre known for lumber not washers.

Our oven is 3 years old and the last time I used the self clean option caused the control panel to malfunction. Now we have to buy a new panel. The repair guy online advises people not to use the self clean as this is a common problem!!! What? I cant use that feature? That is so ridiculous!!! Now we have to pay $300. Whatever happened to the Maytag claim to quality and you would never see a Maytag repair man? Something needs to be done about the problem of appliances and electronics being so poorly made and basically disposable.

It’s a nice look to your kitchen first, and an easy clean. Works great for heating up stuff in a hurry and makes popcorn perfect on the popcorn button. Does ok at melting things. I have been happy with mine for 3 yrs so far.

Our new refrigerator was pissing all over the kitchen floor. We had to disconnect the ice maker after an alleged repair part was supplied. (We had to pay a plumber to install it.) It didnt work, so we finally had to disconnect all the parts related to the ice maker. Here it is July, and ice cubes would really be appreciated right now. I get angry when I see all the Maytag commercials that pop up on the internet!

Last August I bought the Maytag Bravos XL. I have had 3 repairmen try to fix my problems with it and they cannot. The problem is, they cant fix an appliance that isnt designed correctly! Without water, one cannot wash. Dont be mislead that the huge area inside can be used for large objects like sheets and comforters. This machine is MUCH harder on my sheets and comforters than my old machine with a center agitator. I have shredded rugs, holes in sheets, black lines on clothes and a chlorine dispenser that puts spots on everything. The detergent dispenser hardware is rusted as well. Folks if this machine was an automobile, IT WOULD BE RECALLED!

I purchased my Neptune Washer in 2005/2006. I had a mildew problem, and the store told me to clean it with bleach. It is now 6 years later, and the ball bearings are going out. I called two different repair companies, and were told by both they would save me the call out charge, because the ball bearings were going out, and it would cost between $ 600-$700 to fix, so I may as well buy a new one. The washer is only 6 years old. This is completely unacceptable! I then tried to find someone online to fix it, and I ran into the fact that the Neptune Washers had a recall. Why was I, not notified? I bought the washer and dryer set from a Maytag store. No one tried to reach me. I am now stuck with the problem of buying a new one, and really cannot afford one at this time. I went with Maytag due to the brand name, and I knew it would be reliable. Is the joke really on me? Can someone please call me, and point me in the right direction?

When purchasing new, sales person highly recommended Maytag products. Maytag Dishwasher MDB7749SBW3 - This had the SS tub that my wife was looking for. Now only 19 months later it has completely stopped working. A few weeks ago the lights on the control panel would randomly come on or not align with the wash option that was chosen. This lasted a short time, and then lights on the panel would stay on, and not allow you to choose any options. I reset our breaker and this alleviated the problem for another week or so. Then it stopped working all together. A quick Google search and it was obvious Maytag has a MAJOR and KNOWN issue with this model. The ribbon going into the faceplate/ control board sits directly behind the port that exhausts the steam. This ribbon over time becomes corroded and eventually malfunctions. I called customer support. They were completely unwilling to acknowledge the problem and also unwilling to help in any way. They offered to sell me an extended warranty @ $329.00 that would cover the service call and repair. Very unhappy that their product has an obvious defect/ flaw and they are completely unwilling to acknowledge/ or stand behind their product. We are a family of (3) and run this dishwasher about once every 5-10 days. Unbelievable they find a fail rate within a year and half with light use acceptable!

The Maytag Bravo is a big waste of money. Get a less expensive machine. You will have no problems and save money. This is my experience: SETTINGSYou cannot control the settings completely. Every setting is preset. For example, if you choose the Bulky setting, you cannot choose the water save spray rinse. Those two cannot be selected together. Certain settings can only be selected with certain temperatures. This will however be the least of your problems. WASHINGIt does not get clothes clean. I have had instances of items coming out with still stuff stuck to them, not just stains, but actual solid material stuck to it. My cat threw up in his bed and when I got it out, it still had small pieces of vomit stuck to it. I have always only used the Bulky setting which fills up the whole drum, so there is sufficient water to wash. I cannot imagine what it would be like if I used the Normal setting. Many times I had to wash thing twice. If you use the normal setting, you will get hardly any water. It will be a moist bundle of clothes moving like a big lump. You need water and some degree of friction to eliminate the dirt. SPINNINGIt is constantly stopping, beeping and showing me the UL sign (uneven load). You have to unravel the items and reposition them Around the drum. If you are an old lady like me, this is a real chore because the items are now soaking wet and very heavy. Also, because there is no agitator, the items come out in knots (tied to one another) and you have to separate them. DURABILITYThe lid is loose. It looks like it may be missing a screw on one side. It still locks, but it moves sideways when you close it and open it. BOTTOM LINEThe whole thing is a disaster. Get an old fashion type. It will work better and you can save your money. I honestly think there should be a class action suit against Maytag.

My dishwasher is less than 2 years old. Dishwasher will go on when we are not in the house. Cant control the panel. The control panel lights all come, have to cancel to stop the machine. This could be a fire hazard.

We purchased a Maytag Refrigerator-Freezer from Home Depot, in July, 2014. The first two months we had this appliance, it would not make ice (we purchased one that had an ice maker it the freezer!). After numerous calls to Home Depot and about 7 service visits, the service company gave up trying to get the ice maker to work, and instructed Home Depot to give us a replacement refrigerator. The new one came with an ice maker that works some better, but still very slow in making ice, and the new refrig makes a grinding noise every time we open the door. The Maytag Company, whose service people never have anything to do, say this is a cosmetic problem, and they refuse to fix it.Have been in consultation with Whirlpool Company (who bought out Maytag I assume), trying to get the appliance repaired... or at least put an end to the grinding noise. We paid a lot of money for this refrigerator freezer, and have had nothing but trouble and issues with it. If you are thinking about buying a Maytag refrigerator -- Dont!!

Maytag Dryer model # MEDC400BW. I purchased this dryer in March 2015 the fuse went out in August. It is now November and it is out again! I have been buying Maytag since I left home at 18. I am 62 now, so I have been a loyal customer because Maytag was a great product. Not anymore since Whirlpool bought them out! You have to call them to schedule a technician and then it can take anywhere from 1 week to 3 depending on when they get the parts because they have to order them, and nobody else can come out to work on it if it is still under warranty! This is so lame and just not right.

We purchased this double-oven range (model: MGT8775XW01) about 5-6 years ago. It came with some slight bubbling on the plate that the control knobs go through/are mounted onto. A few years later, the bubbling paint began to chip/peel off - revealing rust (its a white range). I bought some touch-up paint, but that didnt look very good. Now that entire plate is bubbling and peeling and makes the whole range look like crap. My wife swears well never buy another Maytag product...EVER! Shes ripped! I cant seem to find the replacement part to purchase. Lousy products!

All I can say is what a mistake. Had a front loader that always smelled and had mold around rubber gasket in door. So, wanted a top loader this time after old GE died. Unbelievable, not enough water to clean clothing. Clothing comes out with some dry spots. And the worse thing is washing black items, tiny particles on black pants, shirts, etc. Think is lint not soap but not sure. You have to rub all over the clothing to try and remove. This washer is 8 months old and I have cleaned it with baking soda and vinegar mixture thinking this would help, it doesnt. The spin cycle sounds like a rocket ship taking off. Lots of banging noises during operation also. I have invested a lot of money thinking Maytag is rated high. It is a pretty grey color with glass top. Well I was fooled, not only the saying looks arent everything for people but its true for washing machines. I have gotten multiple mail from co. wanting me to get extended warranty. Think I will, usually dont, cause I think it wont be reliable. Wish I had my washer from the 70s and 80s. Plain old wringer that got things clean. Just put black pants in dryer on very low heat taken out damp cause I dont dry a lot of my clothing. This seems to have helped to remove stains (soap)/ lint. but, talk about wrinkles, oh boy, this machine has that spin cycle going 100 miles a minute. And if you pick a lower spin speed things come out wet. I actually can say I hate this Maytag Bravo. Things dont come out clean, wrinkles beyond control, very loud. Please folks check out your sites on the internet before buying Maytag.

The dishwasher would not start July 30 2015. Tried to get service around here and no shops could respond. Called Midsouth Distributors for circuit board. They did not have one but would order and gave me the part # W10595570 based on the Model # MDB7749SBW3. Hoping could find one quicker somewhere else. Ordered one overnight from Sears and planned to replace the board by myself. However, I noticed the flat wire with 14 wires in the ribbon cable had brown spots. From my experience in the electrical systems, I realized this must be shorting out the start signal to the dishwasher logic controller. Sure enough, after scraping this off with a sharp knife, I was able to start my dish washer.My previous MAYTAG lasted 20 years. I bought this one in February 2014 at Home Depot. The design for the electrical controls is obviously very poor as testified by so many angry owners. MAYTAG should be required to replace all these control panels with a improved design at their cost. I hope this obvious poor design of a part gets attention in the United States and ConsumerAffairs will help us. I have called 1-800-688-9900 and registered with MAYTAG a complaint about this poor design.

Major issues with the Aqua Lift Range. Takes forever to preheat the oven, 15-20 minutes to reach 375 f- 400 f. Aqua clean cycle not efficient and does not clean at all. The stove top is impossible to select and keep the heat consistent. When adjusting the heat up or down when you slightly move the dial it overreacts. When moved the heat sways may more than selected. The fridge works well but the bottom drawer is way too flimsy and it wont last a long time as it will crack. This is our first purchase of Maytag appliances and it will be our last. Our old 10-year-old stove worked much better than this one. Sincerely, Russell ** & Linda **, e-mail= **

Sounds wonderful. Thats what I thought when I let my son have my 20-year-old, still running older washer. I wanted a new one. It worked good for 3 years and then one night I went to throw the clothes in the dryer and its full of water. After the last rinse and spin, it filled again and stopped. So I tried it on every cycle and got the same results. I thought, No problem. We have a great, honest repairman. Ill call him the next day and hell fix it. When I called and told him what type of washer it was, he was surprised it was working at all. Seems they had a problem with water leaking into the transmission. Apparently, I was lucky that mine had worked for as long as it did. Like I said, Im lucky to have an honest repairman. He told me he could charge me to put in a new timer and solve that problem, but I shouldnt waste my money since it is just a matter of time before it goes bad. Seems they were all bad and Maytag never made good on them. Told me the smartest thing to do would just to go ahead, bite the bullet and get another. It will be here Tuesday morning. Hopefully, this will be the last one I have to buy (keeping my fingers crossed since I had hoped the Maytag was going to be the last). My old machine is still running great for my son. Over 30 years my repairman has had to fix quite a few things for me - ice makers, dishwashers and even a timer on my old washer. Thank goodness he was honest enough to not fix my washer. I dont know if there are even any Maytag products around now, but if there are, they will never get my business. I spent a fortune on a machine that should have lasted the rest of my life. Ive had childs toys that lasted longer. My advice is do not buy Maytag.

I purchased a Maytag Bravos 500 Series HE washer. 3/2013. The machine sensor started giving problems less than 2 years after purchase. The sensor is not working. The wash lights stays on, and the clothes are not cleaned. I have to manually turn the dial to put in on the rinse cycle and then turn the dial to the spin cycle. Its a piece of junk. I called Maytag twice and the only thing the representatives on the phone say: I will send a certified technician to see whats the problem. Price: $129.00 service call and additional costs for labor, parts, etc. Maytag had a very good reputation for its products. Will never buy anything Maytag or any products that fall under that brand.

I purchased a new Maytag from Home Depot. It was delivered and installed by them on 7/20/12. Today is 9/18/12. It is less than 2 months old and the tub is starting to shred around the upper rim. I called to get it repaired. What a nightmare. First I tried to understand a Filipino woman through a bad connection. She advised me to call a different customer service number, 1-800-688-9900. I talked to Crystal. She called up information on me using my phone number. She asked for the serial number as she had the model number available from the online registration I completed on 7/20/12. I told her I do not have that and asked where it was located. I also told her that I was unable to get it at this time as I am handicapped. She advised me that I had to show my repairman the receipt or I would have to pay a $60 service charge. I get nervous about throwing good money after bad. So I then asked why. If the serial number is so important, why is it not a required info when you register online? She had no answer. I asked to speak to her supervisor. I waited 4 minutes. Enna finally came on the line. She gave conflicting info about my online registration. She said I was not registered online (if not, how did Crystal have all my other info including my model number? Why did Crystal tell me I had registered without the serial number?). Enna told me that the repairman could key in the serial number when he gets to my house and if my washer was under warranty, I would not be charged. Again I asked why, if the serial number is so critical to the process and with all the info they seem to have on me (name, address, phone number, model number, place of purchase, date of delivery, etc.), why is the location of this very critical number is not in the owners manual? Why do they allow you to register without it online and why dont they track sales and delivery by serial number? She was unable to address these issues. I asked to speak to her supervisor. She told me she would give me her supervisors name and number (Kim, **) but she would not give me a last name or contact information. She told me that she was the highest level that I was allowed to speak with.Bottom line, my Maytag is falling apart, getting through the red tape to get it fixed under warranty is silly. Maytag ignores its own concept of tracking by serial number and does not support the use of serial number by telling you where it is located on an appliance or requiring it to register online. Calling customer service is a joke! I was mad when my new $800 washer started to fall apart. Now I am just sad with the way we allow manufacturers to treat us. Mad about the way we allow them to operate in the United States. They create junk or junk parts overseas, products fall apart over here, calls for repair get routed around the world, and then they create more red tape and call it customer service. I made one bad choice. Hopefully, you are reading this and can avoid your own.

From the beginning, the blower motor (for the control panel? never needed one before) was too noisy. I just bought the oven from Lowe’s. They sent out a repairman. He replaced the motor, but has exactly the same level of noise. It is bad design/engineering. Im going to try some other brand. One problem is that you cant listen to the fan noise before you buy the oven and install it. And there are no decibel requirements or ratings. Industry regulations need improvement. Model MEW7527A, bought new in Dec. 2012.

This Bravos 300 washer has never cleaned clothes adequately. I have 3 sons who are athletic and this washer does not clean sweaty or dirty clothes even with extra rinse. Now my machine is 4 years and 3 months old and it needs a new bearing which will cost me $385. The repairman said this is a common repair in this machine. Maytag should be ashamed of the poor quality of this machine. I am now looking to by a new traditional top loader. These HE machines are a joke. I am contacting them to make a complaint and see if anything can be done.

Mine is the Chrome Maytag four-burner cooktop model. About $700. I installed it with ease. After two years there are only one or two slight scratches. It sees full meals for two cooked daily. The grate is first class and looks new, the top itself is easy to clean with a damp soapy cloth and mineral oil. There is easily enough BTU power for any size of pro pan. The igniters are healthy and fine and a repair would be easy.

The Maytag Neptune FAV6800AWW Washer has to be the crappiest product I have ever bought. I bought it brand new and hardly ever used it. The first time it broke it was luckily under warranty, although we had to pay for the repair man to install it. It took two new circuit boards before it was fixed. A few months later, the circuit board went again, and it was conveniently for Maytag now out of warranty. The repair man told us that their company never carried these washers because from the get go they had a ton of problems. He said that the odds of it breaking again were great and that we would be better off putting the money into a new washer.I dont understand how the company, in good conscience, could continue to sell a product to consumers that they knew was faulty. It was not a cheap washer and I have never been so disappointed in my life. You would think they would have had a mass recall or, knowing how many problems consumers were having with the product, offer so much money towards a new one.I laugh at the commercials where the Maytag man was bored because their product never broke I could have kept that man busy for months!

I bought the quiet series 200 dishwasher about 2 years ago. The control board went out and because it was past the industry standard one-year warranty, we were told we need to pay the cost of repair and parts ourselves. Well, I came here and seen that there were numerous complaints about that board specifically with all their models of dishwashers. I called and raised hell two times, and then I found them on Facebook and publicly bashed them there on their own page. They got back to me there and gave me an email address to explain my problem with their product. So I did. I even copied this web address and pasted it to my complaint. First, they called me and offered the part at 50% off. I told them, Go to hell. Even at 50% off the part combined with the techs labor, Im still better off buying a new machine and it will not be a Maytag ever again! A week after that another phone call came from them, this time saying they will cover the part 100%, but no labor. I agreed and for about $180 I got a new control panel installed and a one-year warranty on everything except cosmetic damage. Not bad, eh? Certainly not typical, I was told by the repair guy. Be angry, be respectful, but be persistent and public! That’s my advice.

I purchased these appliances on 02-10-16 from Home Depot in Loganville Ga., for almost $2000.00. I filed the first repair call less than 3 weeks after delivery. The sensor panel was bad and had to be replaced. Now 8 months later the washer is not starting, AGAIN. The dryer will only dry one load a day or you get the AF code. This means that the dryer cannot push air over 5 or so and we need to have a vent booster fan (an additional $200.00) installed plus have an electrician run a new outlet. I returned to Home Depot with my complaint. Feeling that I have an inferior product, they tried to get Maytag to make it right. Maytag refused to offer any solutions whatsoever. Home Depot refunded a little over $300.00 for my inconvenience.The washer is an absolute ill-conceived piece of junk. It is ROUGH on clothing and does not remove soap. I started out with brand new (expensive) towels when I purchased this machine and 8 months later all of the hems have been snatched off and theyre unraveling and falling apart and are slowly becoming car wash towels.You cannot wash delicates in this machine and allow it to spin. Underwires in bras are badly misshaped or broken completely. You cannot wear them afterwards without being gouged by bent wires. The only way around this is to take away the spin cycle, but you better be ready with a clean garbage can to haul the dripping clothes elsewhere and hung up to drip dry. The washer has NEVER removed all of the soap from bed sheets. I have a dark gray set that show the soap best. Now I have to wash once with soap then wash again with no soap. This negates the machines being efficient.Unfortunately, I found the negative reviews AFTER buying the machine. My complaints are well known to Maytag, seeing has to how the same complaints are found online as far back as 8 years ago. I have been brand loyal for 30+ years to Whirlpool and thought that I was moving up with a Maytag, based on my parents 50 year experience... I was wrong! I will never purchase another Maytag product nor Whirlpool since Whirlpool now owns Maytag. I have researched and am of the opinion that Speed Queen is a far better product and plan to junk this set and replace them with Speed Queen.

We purchased a Maytag Bravos Automatic Washer 6/28/09. The interior enamel around the bleach dispenser started rusting about six months ago and it’s getting worse. Our white clothes are getting rust stains on them. Otherwise the machine works well, but what a huge flaw. We will buy a new machine, but not a Maytag.

I had one set of Maytag washer and dryer and I loved it. I bought another set and hate it. The washer smells and has been fixed a couple of times and the dryer is bad. I had to have a drum replaced because of one of the bars inside. I paid for the insurance but the bar was considered cosmetic. It has fallen off again after about 2 years and Im sick of it. I will never buy another Maytag again. Repairman, of course, had to order the drum and then I had to take another day off work to be here when it was delivered and one more to wait for him to come. I am so unhappy with this brand - never again.

I wrote earlier about my dishwasher needing to have an electronic board replaced again. So I called the helpful (I say that with sarcasm in my voice) 800 number. My dealer asked me to call for help with paying for the new part. After an hour and a half of being cut off and put on hold, I finally got through to a person that could take my request. The gentleman explained to me about why they would not stand behind their product which was only 3 1/2 years old, and a replacement part that lasted only 11 months. He expanded on his thought about how it was too old to fix and the part was more than 90 days old. I am out of my $1,100.00 with no help in sight. Totally upset with this company and how they will not stand behind a poorly made product!!!!

Well I like all the other people have the very same problem. Ruined floor from sheet of ice that forms on the bottom tray daily. I was told I need a new main board which I understand is about $500.00. I am 55 years old and this was my first brand new fridge. I am so so upset. I grew up with the whole Maytag repairman commercials where he was so lonely cause he never had any repairs to do. All my life I grew up with these commercials. I thought I was buying the best. What a disappointment. It has been in my living room for 2 years. I keep thinking something wonderful is going to happen. Now I have to pay someone to haul it off. Great.

We just replaced our 20-year-old washer and dryer for a new Maytag Bravos set. The Home Depot staff convinced us that top loading units were of good quality and reliable. We were fairly satisfied with our expensive purchase when our washer stopped spinning. We are just past our 1-year warranty of course so we called the service department. A young man in a beat-up pickup truck showed up and spent his time reading the manual that was hidden under the washer. His best guess was a $300 part plus a $100 fee for him to show up. So to repair a less than 2-year-old machine is $400. Im tempted to buy a different washer. It wont be a Maytag, unless you can convince me otherwise. I give you credit for great advertising! I was convinced that Maytag was a good name with limited repairs.

I specifically bought the washer because it has an agitator and you have a setting for more water if you need it. My previous washer had no agitation and really miss that. Seemed like clothes got cleaner. On this machine the agitator is certainly helpful, but there is so little water sometimes I find a pair of jeans with dry spots when load is complete. No, I do not overload the machine. If I change the setting to add more water I don’t see a difference in the amount of water that comes in. I find myself frequently adding an extra rinse. I feel that while making the new washing machines eco friendly they have cut back on water conservancy too much. At the very least the consumer should have more options as to levels of water. I would not buy this brand again.

MF12569YEM2 - Purchased refrigerator less than 2 1/2 years ago, also started having issues with ice forming in bottom freezer and leaking on to floor. I shut the water source off to the water/ice feature, but it didnt solve the problem. After getting on this site and seeing the issue is quite widespread it seems that it should be considered a manufacturing defect. This is the second (actually third) Maytag Refrigerator we have had, one had actually needed to be replaced about 13 years ago because of electrical problem which service man said could cause it to catch fire. The replacement (different model) worked fine for about 11 years... so we decided to try Maytag again... WHAT A MISTAKE! After reading about the multiple problems we can look forward to and endless service calls I too would never purchase any Maytag or Whirlpool appliances in the future...maybe the company should think about the impact on lost consumers!

I purchased a Maytag model no. MDBH979AWB dishwasher on 4/28/2010, and I did not take out the extended warranty. I thought a Maytag product was built to last, but according to Maytag, I am wrong because they only offer a 1-year warranty on their products. About 2 months ago the hi-temp button on the control panel stopped working. Then a few days ago, the START button stopped working, I emailed Maytag and they sent me a PDF file that shows the warranty is only 1 year. I purchased the dishwasher at Home Depot, I went there and talked to customer service, they were no help either.I am very disappointed in both Maytag and Home Depot for selling products that Are CRAP! I paid $499 for this dishwasher, and if I would have known it only came with a 1-year warranty I would not have purchased it. I will no longer purchase any products that are made by Maytag or any products associated with Maytag.

If the control panel light on your Ice2O refrigerator starts flashing you will learn about the Non-Customer Service of Maytag. The problem is the High Voltage Control Board. Maytag has been aware of this defective part since 2007. At one time Maytag was fixing these at no cost to the customer via a recall. Then conveniently in 2011 the Japanese tsunami wiped out the only plant in the universe that manufactures the part.Now out of the goodness of Maytag’s corporate heart they offer the customer $300 off of a $2300 replacement (Oh, I am so grateful). It is time for Maytag (Whirlpool) to accept responsibility for a defective product and recall this refrigerator with a replacement. In the meantime if you have this problem, my advice is to go out a buy a non-Maytag/Whirlpool product since Maytag/Whirlpool cannot be trusted to stand behind their products. Please share this post with family and friends to prevent others from experiencing Non-Customer Service.

Maytag washer Model #: MVWX655DW - I purchased this machine at Lowes in May of 2016. Always was a loud machine but seemed to work ok. In April 2018 the machine stopped working correctly. The spin cycle would lock up and not finish leaving clothes soaked. Called Lowes and waited for their repairman. He came and said it was the clutch and drive motor. Repair is over $400. Machine is worthless. Huge mistake. Never buy a Maytag. I called Maytag to see if they would warranty it. They basically said, Sorry only a one-year warranty on it. I told them the reason I bought it was it had 10-year warranty on it. They said only certain parts but its the drive motor that is clearly marked on the machine that has the 10-year warranty. I was told, No sorry. What huge waste of money. I am out close to $600 and Lowes only give you a store credit with their protection plan.The credit is not enough to purchase another machine without more out of pocket expenses. I will never buy another Maytag and I would not recommend anyone else does. Their warranty is a huge joke. Their customer service is terrible. Maytag should not even bother sticking the 10-year drive motor warranty on their machines. They do not honor it. My advice do not even consider buying one. You will be out the money and be purchasing a new machine within two years.

Food stored next to the ice dispenser freezes. Freezer floor builds up with 1 1/2 to 2 of ice every couple of weeks, door wont close and water leaks on floor.

I have the Maytag Gemini Double oven 5 burner stove. It is great! I use the smaller oven more than the bigger oven. Holidays and cooking are a lot nicer with my range oven. The turkey can be cooking in the lower oven while pies are baking in the smaller upper oven. I have had my range for a while now but I have not once had a problem with it.

Purchased this Calypso machine as a second machine for my ranch to handle really dirty clothes. Purchased from Sears Outlet as a refurb machine would be fine for the purpose. Machine was alleged to work by Sears. Paid several hundred for the machine, brought it home, and voila it does not work. New hoses, ran all the checks, and will not fill. Called Sears and, despite the statements of the manager, was told that I have to have a 3 day old machine repaired and not replaced. This POS did not even work out of the box. Years ago I had a Calypso which is now a flower pot. Junk, Junk, Junk. NEVER buy anything from Maytag or Whirlpool.

Bought a new Maytag High Efficiency washer. I followed the directions closely, using the proper type and amount of soap, and the proper settings for the soil level. The clothes come out of the washer smelling almost the same way they went in. I contacted Maytag by email. Their response was to send me instructions on how to operate the washer. I responded again. Their response was basically Sucks to be you. This is the worst washer Ive ever owned, and the customer service is truly awful.

Before putting clothes in dryer you have to untangle them. Sweaters and even t-shirts become stretched beyond help. Clothes smell like mildew if you leave them in the washer even just a couple of hours. Im 50 and had a few washer/dryers and these take the cake. Ive used the washing machine cleaner/refresher (something I have never done on washers in the past) and still a mildew smell. The dryer has lint on both sides of the lint screen. And as stated before if you dont untangle your clothes they come out in a big knot, partially un-dried & very wrinkled. The lint on both sides of the screen concern me - Ive never had a dryer do that before. Its not much lint on one side but enough to think something is not right.

I purchased a Maytag top-load washer 16 months ago. I had a problem with it four months after purchase and they told me it was not leveled, which I did not believe. I set it up as the manual said to. The washer left clothes soaking wet about every 30 loads. I continued to use it and the washer finally quit working after 16 months. The repairman found the nut which holds the pulley on the shaft that turns the drum had been loose and had been this way for some time. $129.00 later, it was fixed. It works fine now. I wonder if this problem should have been caught on the first service call when it was still under warranty.

There are few nightmares that worm their way into reality, but the forcing upon us of the low water washing machine has excelled beyond mans wildest imagination. A tool which everyone finds an absolute necessity is now a tool which does not work! In reference to this particular machine, there isnt enough water to wet the clothes, it beats the garments with such viciousness, even on hand wash, pieces go missing off the clothes, ripped into oblivion. You no longer can buy a machine which does not SENSE the water level, so we have all been reduced to either buying new clothes every week, or wearing crumpled wrinkled disasters which arent quite clean, and we get to use 3x the electricity and waste 3x more water, not to mention wasted time in repeating the process in hopes of getting our clothes clean and wearable.

MTB2656DEB - Well my fridge is now about 12 years old and from the beginning it was horrible ice as always forming under freezer door. The cold cut draw broke 3 times with its cheap junkie plastic. I hated it from the beginning. I have owned a GE double door with ice maker for 26 years. Wish I had kept it.

I bought my Maytag Bravos washer and dryer set about 4 years ago when I moved into my home. The performance of the washer has always seemed mediocre. Despite using the correct HE products, clothes dont get as clean as with other washers I owned. Many times the washer becomes unbalanced, gets the UL code and I need to move my clothes around to get it running again. A few months ago, the washer started a new behavior: stopping during the initial fill cycle and displaying an F1 error. I soon figured out if I hit cancel and then start again several times, it would resume filling and proceed with the cycle. Over time, I had to repeat it more and more. I read about other complaints and suggestions on the internet and tried pulling the plug for a few minutes to reset the control panel as well as turning off the breaker to reset the machine.After troubleshooting the problem for 15 minutes or longer, the machine eventually runs. Then I can run subsequent loads with no problem. After a week or longer of doing no laundry, when I try to start the machine, I need to go through the entire process of canceling the wash load and terminating electric power to reset the machine. I have called Maytag/Whirlpool and got unsatisfactory answers. I only wash two to three loads of wash about every ten days and sometimes even less. The 800 number for Maytag was automated and would only schedule a repair without asking about the specific problem or being able to talk with a person. There was no way to cancel the service call scheduled and I had to call another 800 number to finally speak with a Whirlpool representative who tried to help me. She connected me with A&E Factory Service to cancel the service call.Both representatives stated that most likely the control board is the problem and the cost for diagnosis would be $130 plus the cost of parts, which could run from $200 to $400 since Im no longer under warranty. I canceled the service call as the cost of repair would be easily be almost half or more of the cost of purchasing a new (and different) machine. This is the electronics module, something that shouldnt be worn down or broken by use or even user error. This is an integral part of the machine and if it has a fault (which it clearly does), the manufacturer needs to stand behind it and help the consumer. The customer service manager even admitted that models with other model numbers had had similar problems and a free control board was sent to those customers. But my model was not in that range.”I had purchased a Maytag Bravos dryer at the same time as I purchased the washing machine and the dryer had a problem within a week of the warranty expiring. A service repair person came to my home to repair the dryer as it was barely a year old and I did not use it for several months that year (due to other reasons). From the volume of complaints Ive seen online, the Maytag Bravos washing machines should have been recalled and repaired or replaced free of charge.

I purchased a Maytag dish washer (not even 2 years old yet). I bought it on 8/29/10 and I paid over $400.00 for it brand new. The model number is MDBH949AWW1 and the serial number is F03422327. I am only asking for the part (motherboard). I have lots of friends and associates at church, work and social that I have talked to about this Maytag. And I would like to give a good report about the company and what they make and that they stand behind their workmanship. I know for a fact that they have 22 motherboards on hand ready to go out and what I have read online is that many people are having the same problem. I need a motherboard. I believe this unit should easily last over 10 years, so I am not asking for much. I will have it installed myself. I just need the part. I trust that you are a reputable company that has been around for many years and Whirlpool has taken new ownership and they have been around for a long time, too! My own parents owned one for over 30 years. This is all that I would request. I’m thanking you in advance.

We recently purchased a Maytag refrigerator, love it, no problems until the mystery person in my house accidentally broke the slide out door for bottom drawer. So I called Maytag, and with no questions asked they sent me a new part by Purolator! Great customer service makes everything better! Thanks Maytag.

This machine is not backed up by Maytag unless you purchase an extended warranty. I tried to contact Maytag regarding this machine breaking in less than two years. This machine has all the bells and whistles but dont expect to use them all because as soon as I used hot water or steam, it affects the lid lock assembly. This should be a recall from Maytag. They know it happens but arent doing anything to improve or remedy the situation. I was only able to use this machine with cold water after this happened. I spent more money getting this washing machine fixed than it deserved. Im so disappointed with Maytags customer service and their product.

Ice maker stopped making ice within first month. Repair man came out next day. Said ice maker only makes 7 cubes at a time 8 times a day. REALLY? A $2000 refrigerator only makes 50 ice cubes a day??? Why would I need a refrigerator that size if there was only one of me? Obviously, Ill be keeping a bag of ice nearby.

Purchased this dishwasher about 1 1/2 yrs ago. Luckily the first two times the control panel went out, it was still under warranty (within the first year). Now its gone out again! This is the third time! What happens is all the buttons will work except for the START and CANCEL. This has been the same issue every time. I tried restarting it, made sure there was not a leak that somehow was getting to the internal electrical components in the panel. I actually know the Maytag repairman by name. Its nothing like those old commercials where the Maytag repairman sits around and has all the time in the world because their products never break. Those days are over and these guys are busy working to fix these devices they label as dishwashers. Since my warranty is now expired, it was an unexpected $96 service call to tell me what I already knew - Its your panel again sir, it needs to be replaced. Well have to order one for you and itll be $265 for parts and labor plus the $96 service call = $361 repair for something that will likely break again in a few months. Never am I buying a Maytag product again.

I purchased a Maytag side-by-side refrigerator in May 2010 to replace a 20-month-old Whirlpool fridge with a dead compressor. The now 14-month-old Maytag has a dead compressor. I have been told by the repairmen that I have come to know that the compressors used in these units are of poor quality and do not last. That must work out well for the appliance industry if consumers must replace a $1,000 + unit every year or two.To Maytags credit, I spoke to customer service and they agreed to cover the parts and labor for the repair even though it is two months past warranty. Maybe I can get another year out of this reliable appliance. I am told that all of the major brand appliances use the same compressor.

We purchased a new Maytag french door refrigerator and from day one had issues with the ice maker. After three replacements Maytag informed me that this was an inherent issues and no fix available. So we had a $2000+ refrigerator with a non-functioning ice maker. Our 20 year old Frigidaire continues to make ice with no issues. Then the control panel lights started blinking and evidently this is also a known problem and when I called Maytag to buy the part, they said SORRY we dont offer parts on our appliances over 6 years old. This is the worst piece of ** I have ever owned coupled with the lousiest customer service in the world. I will never buy another Maytag.

Washer Bravo MVWX655DW0 - Maytag has shipped the wrong part twice, sent me the right part which is faulty and the 4th one arrived today. I have not had a washer since 9-16 October 9, 2017. I am writing to tell you about my experience that Ive had with Maytag over the last 30 days. I have owned several Maytag and Amana appliances in the past; along with owning several currently. Over the years, weve had a wonderful experience owning these appliances however the last 30 days is one that has been unbelievable. On September 18 on a Monday early in the morning I called Maytag service line. I spoke to a young lady who had difficulties finding me in the system and did not know how to make an appointment to have a Maytag repairman come to my house to look at my washer. I did not take down her name as I thought and trusted that the company was acting on my behalf and would take care of me.I spent several minutes explaining to her that I did not live in Indiana that I lived in Iowa and that I would need a repairman who is close to my hometown. She continued to give me phone numbers with area code 407 in Indiana and then kept repeating some type of a ZIP Code 49 something for Indiana. I explained to her four different times that the zip codes in Iowa start with a five and the area code would be a 515 number in the area she was looking at. She finally gave me two phone numbers, one that did not work. I asked for a repairperson out of Jefferson. She told me Cranston Repair and gave me the phone number. She told me to call him. I told her that I would go with the Cranston repair since Jefferson with my hometown and it was close to where I lived.I then asked her if she would make the appointment. She told me she didnt know how to make the appointment and she kept messing up with the system. Not sure if it was her first day or not but that was fine so I said “never mind I will set the appointment up myself. I then asked her to double-check to see if our new Maytag refrigerator that we just purchased was registered. She told me she did not see it but all I needed to do was call back the next day with the model and serial number and anybody I spoke to on the phone could go ahead and get that registered. I thought I had registered online; I only wanted to double-check but she didnt see it so I assumed I did something wrong and then would make the call back the next day.I called Cranston repair and scheduled an appointment with the repairperson for the next day Tuesday, September 19. Repairman came the next day on time, looked at the washer and found that the transmission had gone out. I had purchased the washer just shy of two years ago. The repairman said that he would have to order the part and would let me know how long it would take and would return to fix the washing machine. He called from my house and was told that the part was on backorder until October 5. After the repairman left the house I decided to call Maytag back and express my disappointment in the product as Maytag says they stand behind their products and the fact that it was not even two years old and that a transmission would go out. The individual I spoke to this time, Antcwaniqua? Not sure about spelling, listened to my story. She also told me the part the repairman ordered was not correct.I needed part W1 1132267. She said that was a substitute part for the correct part that I needed which was W11035204. I told her that the part number ending in 204 we were told was on backorder until October 5. She said no, the part may show that in the system for repairmen but Maytag can locate the part in a warehouse, it would be shipped in 3 to 5 days. I told her that he had called a place in Davenport, Iowa. What she would do because of all the issues I was having was she would go ahead and ship the part out to me at no cost in 3 to 5 days.I wasnt sure about that warehouse thing. It didnt sound convincing but at that point I had to go along with it. What was shipped out to me was the substitute part W1 113-2267. At this point she told me that I would have to pay to have the part put in; I agreed to that on I want a new washer or I want my washer repaired within 72 hours at no cost. I have not had a washer for 3 weeks plus. Repairman in coming Friday and I am not confident that the 4th gearcase part that came today will work either.

I was so excited to get a washing machine. My excitement quickly faded two washes in when I noticed that the clothes were not completely submerged in water. I checked the handbook and it said that this is normal but at the end of the wash I still had clothes that were completely untouched by the entire washing cycle. The first couple times that the washer was used, I noticed that the water took a very long time to come out. It said it was sensing and then the water would come out in small spurts. When the wash actually started moving, wow the noise was abnormally loud. It continued to make said noise for the entire cycle. I could hear it everywhere in the house. I am so disappointed in Maytag. My father is of a much older generation and he chose this brand based on his past experiences...now I have to tell him its a hunk of junk. Save your money and buy an old fashioned machine.

Our new Maytag Bravos XL machine quit just 43 days after being purchased. Purchased from Lowes, but since it was past 30 days since purchase date, Lowes could not do anything to help. Lowes directed us to an appliance repair service that they use. We had to wait another 3 days for repairman to come out to look at the machine... only to find out that a drain pump would need to be replaced, along w/ the diagnostics board since it was not working either. Parts would be ordered & were expected to arrive 3-4 days later. It has been a week later & the parts still have not been shipped out by Whirlpool. We are now on almost 2.5 weeks w/o a washing machine. I usually research & read customer reviews before making a major purchase. However, we had to quickly get another washing machine & dryer, so felt like Maytag was a SAFE choice since I had Maytag several years back. (That Maytag was your basic washing machine w/o the bells & whistles before machines had bells & whistles.) Will I purchase another Maytag again after this occurrence? Probably not. In fact, I am so aggravated & frustrated at this point, that I would love to just throw the machine out in the middle of the street!

I purchased Maytag gas range in March 2011 at Home Depot, Model No. MGR5605WWO. I received the product in May 2011. The porcelain on the grates chips away leaving large grooves in grate, which affects cooking efficiency, (the fire burns erratically). First, I called 1-800-688-9900. The grates were replaced. And then same problem, it was replaced again, and again the same problem. The warranty to cover stove was extended by 6 months. The enamel on the round magnetic cover for the burner is also chipping away. I was told that this chipping of the enamel is a cosmetic problem and does not affect the functionality of the stove problem.A repair technician was sent out at my request to see firsthand the problem grates. I was told by him that if it occurred again, the manufacturer needs to be made aware of the defective grates. He noted that the enamel covering on the grates was not uniform. I have been told by Maytag supervisor today that she will get back to me within 3-5 days and let me know what is going to be done. I have had gas ranges before, but this is the first time this problem has occurred and its continuation is unacceptable. Is there anything further I can do to ensure I have stove grates that do not chip continuously?

Bought a Maytag 4000 series washer and dryer combo for about 2100 dollars in October 2011. Had a professional look at it today since the clothes stayed wet after the spin cycle. Told us it would cost 1000 dollars to repair the washing machine. So a total write-off in barely four years. I am very disappointed.

Maytag WASHING MACHINE MVWC200XW - Will not clean our clothing. We have been tolerant of Maytags disregard for the people who have trusted their product and name over many years. No longer will we purchase a new Maytag or Whirlpool product. They say third time is the charm but I can not afford to take the chance. I wish them luck, they will need it.

Bought a Maytag Model #MDB8949SAMO dishwasher. After LESS THAN 2 years the motherboard stopped working. Called Maytag to complain, but was told they couldnt do anything. I would give the dishwasher less than a star but the rating system wont allow it.

I bought this Maytag oven (MEW 7627HB) to replace a 20-year-old GE double oven. Upon the first use, I found that it has noisy cooling fans which run continuously as soon as it is turned on and, for some time, after it is turned off. These fans make an irritating, loud, whistling noise. The dealer responded to my complaint, pulled the oven out and performed a complete system test. He then called engineers at the Whirlpool factory, who told him that the fans were a recent redesign made because the previous design didnt satisfactorily cool the electronic control circuit and that there was nothing to be done about the noise. After several weeks, the oven, when in use, continues to stink of overheated electronics. I fear it wont last long.Note that my old GE model, which also had electronic controls, didnt run a fan at all unless both ovens had been on for some time or the self-cleaning feature had been on for a while. And it didnt make a loud noise.

A 14-month-old cabinet dryer required a new motor. I was promised delivery in 3/4 days. Following several calls, all of which resulted in the delivery date being extended to over eight weeks, the same engineer called to install the new motor. He refused to do it as the surrounding paneling had not been removed to give him access to the cabinet. It took another four days for him to return after we called in our builder to remove the panel--three screws and four-minute work. I asked for the warranty to be extended, by way of recognition of Maytags awful service. My request was rejected out of hand and the reasons do not accord with the chronological evidence I hold. I am about to bring a claim in the local County Court.

I bought a Maytag washer November Thanksgiving of 2013. This washer started giving problems three months after; problems such as the cycle stop turn over properly, the light would say wash but its not washing. It would just stop but the light stuck on wash for long periods of time. Press the pause/start/cancel button, it would sometimes start again and stop and let out the water quickly. The clothes would be filled with water and not wash properly. This the funny part, serious funny part. I contacted Maytag on countless time. They had me on hold so long I had to hang up; a hold for hour I am talking about. One day I finally got through. They gave me a number to contact because where I am located there is no tech. I never got anyone but the machine when I called the number after countless times of trying. I decided to called back Brandsmart, because I just think its not right and fair to me to purchase a washer for so much, to had it shipped for more money. It didnt last me NO time at all and I cannot get any help. Well! Brandsmart told had to have paid export shipping, something I never was offered and since I took it out of the country, there is nothing they can do for me. I hunted for my receipt and to this day I I still have it. All was offered was warranty parts and labor for a month, thirty days. I said no because I would not think anything would go wrong in that short period of time. Nevertheless was not offered any export shipping warranty like what they are trying to ** me with. Here is my receipt number **. I grieve presently how I was just robbed of my money so openly when all I wanted was a replacement.

Model MDB7749SBM1, Complete FALSE ADVERTISEMENT and GARBAGE. Let me explain. Maytag clearly claims this dishwasher is stainless steel on the inside and out... FALSE, BOGUS CLAIM. Please check for yourself, tried a magnet to it everywhere and the magnet stuck everywhere. I have had this dishwasher for 15 months. The keypad frequently stuck. When I called Maytag, they told me if its usable, there is no defect. 15 months after purchase and 3 months after WARRANTY ran OUT on Thanksgiving Day with 25 guest. The keypad finally quit for good. I called the Friday afterward and was told no service for a week. I called and received local service but they told me it would need a keypad, which I waited to call on Monday since Maytag is closed on weekends how ironic. I was told they wont cover anything since a certified person didnt come out even though nothing was ever fixed and they blatantly lied to the consumer. Tried to sell me an extended service plan. I will NEVER BUY ANOTHER MAYTAG PRODUCT AS LONG AS I LIVE AND WHEN IM IN LOWES OR HOME DEPOT, I WILL TELL EVERYONE IN THERE SHOPPING THE SAME THING, DONT BUY MAYTAG IF YOU KNOW WHATS GOOD FOR YOU.

My husband and I bought a Maytag Bravos HE washing machine 3 years ago at Home Depot. It is by far the WORST appliance purchase we have ever made in 40 years! This machine started making horrible grinding noises about 6 months. It is not rinsing properly and its leaving detergent stains on our clothing. This washer needs to be recalled. I will NEVER buy another Maytag product, EVER!

I purchased a Maytag refrigerator about two years ago because of the Maytag quality hype. The ice maker has been leaking almost from day one and I need to clear out the ice from the bottom of the freezer every few weeks. Now the thing has quit cooling all together. I contacted the Maytag website and they recommended a local authorized repair firm. I took a day off work to meet the service provider. After checking the fridge they informed me that the problem was with the sealed system and that they could not work on it, and that I would need to contact Maytag to get a real Maytag repair person to come and fix the thing (right back where I started). They were however more than happy to charge me $70.00 for a service call. I tried the Maytag 1 800 number which was a nightmare and it finally hung up on me. I then went back to the website and managed to get a service appointment in two weeks (had to wait for a Saturday appointment because I cant afford to take another day off work). I just hope that this time it will actually be someone who can fix the thing and not charge me just to refer me back to Maytag again. I am not happy with the so called Maytag quality or their BS methods for providing service. Caveat Emptor if you are contemplating a Maytag appliance.

I bought a new Maytag dishwasher installed by East Town Appliance in Wautoma, Wisc. They installed it and ran a full wash cycle and it worked fine. After they were finished, I got all my glasses out and put in their dishwasher all excited to get them clean and sparkling. I started the dishwasher, put on a coat to check my birdfeeders on the deck where I was standing in front of the patio door. I heard water running suddenly. Turning around to see water gushing out of the bottom of the dishwasher. I called East Town back and had the installers return immediately. The pump was stuck open. I called Maytag about what happened and they said they wouldnt pay for the floor damage because it was already installed and to call my insurance company which I did. They went after Maytag and won but I had to pay $500 insurance deductible. I will NEVER buy anything by Maytag again.

Maytag Jetclean EQ Plus Dishwasher - We purchased the dishwasher in June of 2014. Recently the control panel decided it wont work. There is power to the unit. I am told that the unit is no longer in warranty so we have to pay for everything.

Top of the line $1300 Maytag Maxima MGD8100DW probably rusted much earlier before I noticed. After all how many times you check the drum of brand new top of the line dryer?? Manufacturer says not covered. Not sure but already this brand new model has been discontinued, so the manufacturer i.e. Maytag or Whirlpool take your pick found out about the defective design/part but now does not want to honor the warranty ridiculous. And one of the main selling points was made in USA (which turned out to be only assembled in USA), and the consumer reports which gave good rating but they were duped too.

Model MWVC360AW0 has never done a decent job cleaning. Washing pods would not dissolve completely. Ruined a lot of clothes. Had to rewash many times. This is a piece of junk. Extended warrant folks at Home Depot no good either.

Our brand new Maytag dishwasher model number MDB87749SBM2 was professionally installed on 7/31/2013. In fall of 2015 my control panel started acting up. I was unable to select certain wash cycles. The problem would come and go. By January 2016 my lock button would freeze and I was unable to unlock or select any wash cycles. By February 2016 my control panel went out completely. It wont turn on, not a single light. It is fried.When Googling the issue I found that we are 1 of MANY with faulty control panels not only on our particular model but on many Maytag dishwashers. They all seem to have the same problem, right around to 2-3 year old mark. One would think dishwashers would last, like before. A dishwasher shouldnt need to be replaced or need a major repair so soon. The one our new dishwasher replaced was 12 years old and was working just fine. We just wanted to upgrade to stainless steel. Wow what an upgrade haha! Maytag should be recalling these control panels. Their name is no longer a trusted name in our home.

After two years of dealing with this awful washer, I felt compelled to write a review. I have had $50 rebuilt washing machines, as well as new ones from the bargain aisle. They worked very well for us. But when it was time to purchase a new one, we wanted a washer with a larger capacity and ended up with this boobie prize. Honestly, whoever designed this washing machine should be ashamed. I cannot believe it made it past the testing stage! Blankets and quilts roll into a ball and never get clean, detergent gets trapped inside this ball of doom, the simplest dirt on clothes survive the cycles, and forget trying to clean stains. I scrub them out, then use the rinse cycle. JUST AWFUL!!! Honestly, this is THE WORST and most disappointing purchase I have ever made. Stay away from it.

I purchased my Maytag Centennial Commercial Technology MVWC200XW in May 2012. This is the second time in almost 3 years that it breaks down. The basket decided to drop today and by the time I realized that it did, my whole bathroom had flooded, the water spread down the hall into my spare bedroom and soaked through the floor, also flooding my basement. I called customer service. They are sending a repair man next week, but as for all my ceramic tiles that are now cracked in my bathroom and my hardwood in the hall and bedroom that is full of water and are lifting off the ground. Its my responsibility to call my insurances to fix it. Yet it was their washing machine that caused the damage in the first place. When I purchased the washer I didnt expect to have to repair it every year. Not impressed! I do not recommend this washer.

The control panel acts just like the other reviews on here. The cancel light stays on. If I close the door, the washer automatically starts up again. It is unusable and it costs too much to have it repaired. First and last Maytag product for me.

Have had this side by side for a long time and it is great. Have not had any problems with it. Also have had an Amana which we love as well. These are side by side and are frost free and never have to clean.

Maytag is a product that I would buy any time. Even uses it well last for a long time. If you want to spend money this is a good investment for your kitchen and as for your laundry get the washer and dryer. You do get your moneys worth with Maytag.

My Maytag Bravo washing machine is very basic and convenient. It was the first appliance I bought when I purchased my new home in September of 2019. it is commercial grade so I’m able to wash everything from towels to comforters to heavy coats. I like the clean lines of it and the knobs are easy to use and are perfect for my needs. It has wrinkle control, deep water wash, a variety of temperatures including tap, cold, cool, warm and hot. There is a fabric softener feature and an extra rinse. The push button Start is perfect and easy to use.