I purchased the Maytag Bravos MCT HE washer in 2011. Its about 3 1/2 years old and there was a very loud noise when the washer went into the spin cycle. Called the repair man and they told me the bearing and spin basket needed replaced. I had always had Kenmores with very little issues and they lasted for 12 years plus each. I get the HE model from Maytag and cant even go 3 1/2 years without some major issue. I called Maytag (Whirlpool) to complain and they said there wasnt anything they could do. I reminded them that I had checked for recalls on this model and looked into some of the complaints about this washer and that there were many of the same issues that I had plus many others. I felt like there should have been a recall on the bearing since they are going out too soon for this kind of a washer. I guess the Maytag repair man is now busier than ever since I dont see them on any advertisements anymore. Well, I will never buy a Maytag or Whirlpool appliance again after this.

2 major repairs in 8 years, ridiculous! We purchased a washer and electric dryer pair in Feb. 2012, had a repair for the control board (CPU) 4+ years under extended warranty, had another in 2018 for the same thing. I was told power surges could cause it, however I have a WHOLE HOUSE SURGE SUPPRESSOR ON THE INCOMING 200 AMP SERVICE AND KNOW THATS NOT THE PROBLEM!!! Had the same CPU go out again in Nov. 2020 so, rather than pay $370 for the part plus labor, we bought a top loading GE with an extended warranty and factory 10 years on the motor. We will never buy another Maytag product again. We were told that we shouldnt expect to get more than 6-7 years from a washer now, ridiculous. Manufacturers are outsourcing electronic boards overseas to maximize profit and could care less about quality control!!! Junk!!!

I purchased this washer January 2020. Bravos XL model# MVWB830DW5 is the worst washing machine ever. Does not clean your clothes, leaves soap residue on your clothes. Clothes aren’t fully submerged in water for the wash or rinse cycles. Do not waste your money. You will be highly disappointed.

We have a 2 year old Maytag washer and dryer. 10 year warranty may I add. Well, we get 2 frantic calls that say, “They heard an explosion and the bottom of the house is flooded.” An explosion so violent that it shook our 3 story house and sounded like a bomb went off. Our washer and dryer are on the main floor. When we get there we found the washer top was dented so bad that it dented the bottom of the dryer that sat on top of it - blew the dryer door open! Blew the front of the detergent compartment and blew the side apart! Scared my mother and father in law who lives downstairs and who is bound to a wheelchair! Not to mention the fact that it flooded the basement and ruined the ceiling and Maytag says they will replace the washer! Are you serious? Who wants another washer which may or may not explode! What about the damage to my house! This just happened a couple of hours ago! We are very ticked off and not happy with We will replace the washer! Bad, bad business. This is not where it ends! I want my house repaired and won’t settle for anything less! Shame on you Maytag for putting profit above quality! Consumers beware!

I am also frustrated with Maytag for the same exact problem... The control panel and the dishwasher not working just after our year warranty went out. I purchased this product because we had a good experience with a Maytag Dishwasher lasting about 20 years, only to get fooled that the quality is not there any longer. This seems like BAD business on Maytag, Whirlpool, and Home Depot! How can we get an official complaint to someone who can fix this? Another example of big businesses that do not care to take care of customers! Why would a company like Home Depot continue to support this business!!

We purchased our Maytag gas range in 2015. Within 6 months we noticed the clear coat and paint was defective, we called Sears, they allowed us another range top and replaced it but told us our warranty was up in a month and they would not replace another. The stove always looks dirty because the clear coat and paint have bubbled up and it is clearly a 100% manufacturing defect that should be recalled.

I thought washers are supposed to last 10 years or something. 3 years and I have to replace it. I dont know who Im more dissatisfied with - Maytag or Direct Appliance where I purchased it. Just thought I would rant and warn others about this brand. The computer died so it doesnt know what cycle its on. Repair guy said its unfixable. ARGH!

My Maytag over the range microwave has given me nothing but troubles since my purchase. The turntable off feature never worked, and now the side control panel is barely hanging on because of broken plastic connectors. The handle is now broken in half. I will never purchase another Maytag product. Buyer beware.

Purchased this double oven back in 2012 and have had to have the control valves replaced twice because of them jamming and snapping. The burners are undersized for cooking and it takes forever to get water to a rolling boil. The broiler in the upper oven needs constant attention when using it because food cooks unevenly and burns quickly. The lower oven is great, convection is awesome. I have seen the Maytag repairman more from my stove than I have for any of the other appliances I owe combined. Maytag should stick to appliances that only use water.

We purchased a French door Maytag refrigerator model MFD2561HEB in November 2007. In August 2008, the unit stopped working suddenly. The high voltage control board was replaced under warranty, but the tech could not determine why the board failed. I called Maytag to demand a new refrigerator. The best they would do was to extend the warranty for 6 months, no charge. The unit quit twice more in September. A tech was summoned (paid service call), nothing found. It started working again. Since then, the thing has quit several times. We unplug, move all food to a second refrigerator, wait a day, plug it in, and move the food back. The useless box quit completely this week, not quite 5 years of service life. The tech said the board must be replaced again, no guarantee. We declined. I called Maytag again to demand a new replacement and escalated the complaint. They are to call back, ha! In the 5 years of poor service (and poor customer service) from Maytag, the 30-year old second refrigerator has been up to the task of preserving our food. This experience has made me vow never to do business with a Whirlpool-affiliated brand again.

The refrigerator has been very dependable for over 14 years. The biggest problem we have had is failure of plastic tracks on drawers that break and had to replace drawers and other problems with plastic components like deli drawer coverlet, and door shelf door plastic. Recently we have problems with the touch control panel on front of door. Not working properly for ice dispensing and temp. control although temp is maintaining what we had set prior to failure of control panel.

Maytag French Door Fridge Model MFT267AEW10 - Not even 1 month out of warranty and the water line solenoid is leaking. It seems the water line installed at the factory was pulled so tightly that it has caused the solenoid inlet to start leaking. We really researched this refrigerator and thought we were buying the best. Not so, Maytag wont warranty it. The last purchase of Maytag I will ever make. We should have bought the Samsung but we were trying to buy American. Wont make that mistake again. Not a smart investment. Refrigerators are supposed to last a good ten years. How sad.

Purchased new washer mid-February from Maytag dealer. He said machine has few problems and it was a good machine. 3 and one half months later, the machine is dead. No lights on display but power at plug. Repairman comes at appointed time and says it needs a new circuit board. Within a week, the part arrives and an appointment is made to install the new board and still have the same problem. Have to order a new console panel. 3 and a half weeks later, the part comes in. I have a job which I used the money to buy this machine and now the service advisor wants me to take off work so they can try to fix this machine. He told me I cannot return the machine. Whirlpool Canada LP Customer Assistance said they could not do anything. When I asked to talk to her boss, she put me on hold. She came back and said they would give me 6 months extended factory warranty and she would email this which I have not received. Work schedules will dictate when the next appointment will be made.

I grew up trusting and believing in the name brand Maytag. Unfortunately, I wont anymore. I purchased a Maytag MDB7749AWM1 dishwasher from Lowes thinking that I would not need the extended warranty because well it was a Maytag and they just keep working and working for years to come. Not true anymore. 1.5 years after the purchase the control board has gone out. I come to find that hundreds upon hundreds of people have all experienced the same thing. Shortly after the manufacturer warranty expires, the panel dies. By all accounts it is an issue of POOR engineering and Maytag now being produced by Whirlpool. The replacement part is between $150 and $200. Thats about half the purchase price. It is a racket. Companies like this probably think, well if we build something that is going to last and last we cant make money on that. So lets rig it so our stuff breaks right after the warranty and charge half the price of the unit to fix it so we continue to make money either by people buying the part or just going and getting a new dishwasher. Well I can tell you I will be getting a new dishwasher and it certainly wont be a Maytag OR a Whirlpool.

Very disappointed with Maytag Bravos XL, four year old unit with bearings going out. Quoted $400 + for repair. With two in the house, wash demands are normal. Quality is questionable to have bearings & seal going out in four years. Also you cannot buy the bolt which holds the Washer Motor Rotor Cover on without buying the whole $130 assembly. Daughter has Whirlpool brand with same problem. Seems to me this is a problem Maytag/Whirlpool should address. My old unit (that I wish I still had), worked for 25 years. Would not recommend these machines.

We have had our washing machine for about 6 months, we got the F3 E6 error code. After doing some research, we found out that the control module was what we needed to replace. My husband and I called both Maytag and Lowe’s, (the store we purchased the washer from). We have been given the runaround. After talking with several managers in the Lowe’s warranty department, we were told that we had to contact Maytag directly about that particular problem. Okay, no big deal. We called and every single time we were put on hold for at least 30 minutes before we were hung up on. Not once did we even get to speak to a person. If we don’t get a response and our problem doesn’t get fixed, I will be going to the Better Business Bureau.

Great when it works properly and doesnt leak! Quietness, cycles. Everything that had to go in went in, well laid out. Stainless steel, clean, good looking. Anything with the Maytag name doesnt last any more than a couple of years. Gone through a washer and dryer with no help from Maytag. The dishwasher was replaced by Maytag because the main circuit board was on backorder for more than 5 months. Washer was replaced with a Samsung. If I had to replace the dishwasher out of pocket I would go to Korea or Europe to do so. Maytag, what a huge fall in quality and reliability!

This machine (Maytag Bravos XL) was in our new house and is relatively new. It is the worse machine I have ever owned. I am 58 and cant reach the bottom of the tub to get clothes out. It doesnt fill with enough water to clean the clothes, and repeatedly I have my clothes coming out dirty. I have had to rewash clothes to get them clean at all. Or they come out with grime all over them. I had both a LG and Samsung front loaders in the past, if I could afford it I would throw this Maytag out on the curb! Its a piece of junk.

Electric stove range is great. It was very affordable, this stove is very easy to clean and wipe down on the outside. I had it for 4 years and had no problem with it. Would definitely recommend it to anyone on a budget. It also has a warranty which is also a plus.

Because it is the high efficiency model, need to leave the lid open so interior will dry and not smell musty. Also, recommend using a washer cleaner such as Affresh or Tide tablet every now and then. But works great!

Within the first month of purchasing my front loading Maytag Neptune washer (MAH6700AWW) at Home Depot, the soap dispenser fell off. The machine not only leaked, requiring stack of towels to be placed on the floor to keep the room from flooding, but often produced foul-smelling clothes, despite cleaning the machine. On top of that, the delicate cycle stopped working and then last month, the entire control board went! It is past its warranty period, and I cannot afford a new washer for my family of 6. The machine has been discontinued and the parts unattainable. The control board of our dryer (MDE6700AYW) went too, causing buzzing in the electrical connection and burning, causing us to have to shut down the circuits for the machine. Maytag has lost all my respect as a quality appliance supplier. We spent $1700 on the set and the machines have been a nightmare. Please note: we were NOT notified that there were class action suits against Maytag regarding their machines.

We purchased all new appliances 3 years ago including a Maytag dishwasher. Same problem as a lot of others. We had the control board fail three times in just four months. Now today the repairman came and while he was here contacted other Sears technicians and Whirlpool technicians. They came up with the idea to replace the detergent dispenser which they said is causing the main control board to fail. However, while the tech was on the line with Sears and Whirlpool they done troubleshooting on the detergent dispenser and found that it was all within specifications. In fact, that was not a problem because it worked as it should. But in their wisdom they decided to replace the detergent dispenser. We now have to wait another ten days for the part to arrive and reschedule another appointment to have the detergent dispenser that works replaced. The serviceman that was at our house said that they are making him replace a part that is working and that this does not need to be done but he has to take instructions from Sears technicians. Our service person said that he doesnt anticipate that replacing the detergent dispenser will make the dishwasher work but he said if it does it will only last a few weeks as before and then fail once again. We have the dishwasher on extended warranty and there are about 22 months. I suspect that this one will be going to court to get resolved. Never Maytag again or Whirlpool.

I bought this dryer 3 years ago and the fuse has blown three times. The dryer gets really hot and blows a fuse. The entire back of the dryer is clean and free of lint, the hose on the back, and the ventilation pipe running out of the house are completely clear, but the dryer continues breaking down. The Whirlpool NC folks have been out here three times yet it has broken down once again. I should not have to purchase another dryer after only three years!

I am 86 years old and have happily owned Maytag washers for many years. I just recently purchased the front loading model for ease of access. After using it for sometime, I could not be more disappointed. The clothes come out smelly, stained and gray. I tried using affresh washer cleaner on hot setting and the tablet did not even dissolve. There is black mold growing and must be cleaned constantly. I am so sad that my favorite company has let us down. I cannot afford to buy another washer so I am stuck with this lemon!

I bought a Maytag washer and dryer with Commercial Technology, front loader in April 2012. Since then, the repair guy has been at my house three times in six months. This last repair is going to be just $800 in parts, not including any labor yet. So, I called Customer Service, and told them I was not satisfied with the repair job again, because I obviously have a lemon of a machine. Needless to say, I lost, and was told the warranty is only for repair, and not replacement. Well what happened to customer service? Its more like customer bend over, shut up and take it. So, I will get my repair at a cost of at least 1,200 bucks paid for by Maytag. Im not a business person, but if I were the company, I would think replacement of the unit would be a lot cheaper in the long run for this company and a happy customer for the future of me buying brands. Needless to say, I will never buy a Maytag or Whirlpool product again, and you can thank your useless Customer Service department in Canada for that. P.S. I work for a company with over 10,000 employees. I might accidentally send out a little free publicity how this company treats loyal customers. I actually bought this brand because in the past, I was led to believe they were great . Wow, was I wrong!

Major issues with the Aqua Lift Range. Takes forever to preheat the oven, 15-20 minutes to reach 375 f- 400 f. Aqua clean cycle not efficient and does not clean at all. The stove top is impossible to select and keep the heat consistent. When adjusting the heat up or down when you slightly move the dial it overreacts. When moved the heat sways may more than selected. The fridge works well but the bottom drawer is way too flimsy and it wont last a long time as it will crack. This is our first purchase of Maytag appliances and it will be our last. Our old 10-year-old stove worked much better than this one. Sincerely, Russell ** & Linda **, e-mail= **

I have had my stove since 2004. A problem I have had was when I asked it to clean the ovens, it quit working all together. A service person was called. Also sometimes when I turn on one burner, another one will turn on instead. Yesterday I turned on a burner to low, and it did not turn on at all.

I purchased my oven in May of 2012. Ive tried numerous times to use the clean cycle. There is absolutely no way it works. I contacted Maytag on 1/13/14 and their response was to explain the concept of AquaLift Technology as if I didnt already know that. They said I should use the plastic spatula (as if I had not already done that). They urged me to email whenever the need arises (as if that will do any good, they obviously acted like there was nothing wrong with their AquaLift technology). Someone should hold them accountable for their faulty product. Maytag is now a dirty word in this consumers vocabulary, and no amount of scraping ...with a plastic spatula will clean up the mess they sold me. I hope it breaks so I can go buy a product from a company where self-clean does not mean I am scrubbing (with no success) and running a clean cycle numerous times in an afternoon to try and get a spillover cleaned up.

I bought a full kitchen of Maytag appliances when I bought a new house in 2009. I thought it was a reliable company. Id always gone with GE before. I couldnt get the packing sticker off the oven after trying everything to remove it, so the oven bottom is virtually ruined. The timer on the oven dings once and stops; dinner burns if Im not right there to hear it. I was told by customer service thats the way it works, so I had to buy a separate timer. I am now replacing my 2 ½-year-old dishwasher because the control panel has once again stopped working. It cost me $275 to fix the first time and it lasted less than 3 months. I will never buy Maytag again! I got over 20 years of service from my GE appliances.

I am extremely unhappy. This is a terrible washer (Maytag washer MVWC565FW). I am so sorry I didnt buy a GE. Terrible loud noises, shakes and vibrates like a plane taking off. Funny smells as if something is burning. Repairman came 1 week after purchased and stated nothing was wrong. A huge waste of money, I HATE, HATE this horrible machine!!! Totally unsatisfied, I would never purchase anything with the Maytag name again!! Wish I could get my money back!

We are an extra-large family, and required an extra-large washing machine to handle our needs efficiently. We thought paying quite a bit more for the reliable Maytag brand name would be a good investment and worth it over the years... HA!!!! The Bravos XL model has turned out to be a major disappointment! It gives no manual control over the water level and you can actually have things come out of a load dry! The loads continually become unbalanced. Clothing is continually damaged - rips, tears, shreds. Wrinkles everything... even jeans?! Even with proper amount of detergent use and frequent affresh tab cleanings, the clean washer reminder light repeatedly comes on. It leaks from the bottom, although we cannot determine why or exactly where the leak is originating! It is a seriously frustrating, substandard product, and I cannot believe Maytag (and Sears, where we bought it) is continuing to sell this machine (and may I add at a crazy high price)! Both of these companies should be ashamed of themselves for peddling such poor quality washers and leaving their customers so dissatisfied! Stay clear of the Bravos XL!

I have a Maytag dishwasher model mdb6759aws3. The control touch pad broke after 1.5 years of light use. It costs $475 to fix (includes labor). Completely unacceptable service provided by Maytag over the phone. The only concession offered was a 25% discount if I bought the replacement part (control touch pad) from them. After some internet research, I learned Maytag marks up their parts prices over 25% so they are really not giving you a discount at all.I filed a complaint with Maytag but they were unable to provide me with any evidence of doing such except for an 11-digit code. Due to a major defect, Maytag should have sent me the replacement part for free. I told Maytag I thought this was fair and that I would pay for the labor. I will never buy another Maytag appliance again! They are junk and the company does not practice common sense customer service.

My husband and I were Maytag fans, and we purchased the fourth set of Maytag w/d in May 2019, along with an extended warranty. Four sets may seem like a lot, but my husband and I have been married for almost 30 years now. Long story short, the washer went haywire, and kept flashing LF. After searching Google for answers, my husband flipped the main breaker, then unplugged the washer overnight. It seemed like that fixed the problem, but it didnt. I called Lowes for help and got hung up on numerous times. The hang-ups were not due to my attitude or choice of words. I kept getting transferred from person to person and put on hold, then the phone would go dead. Eventually, someone actually spoke to me and gave me an 800 Maytag number to call, which resulted in more hang-ups.As before, eventually I got to speak to a real human being who took my info and said that a service tech would contact me. Well, over two weeks later, no one has contacted me. However, due to my post/review on the Maytag website, a Lowes representative did call me and offered me a full refund on the washer, but not a word was mentioned about the dryer that seems to be possessed because it turns on and off at will. My husband and I have a limited income, and we purchased the top-of-the-line Maytag w/d thinking that it would last at least ten or more years.For the money that we spent, the w/d should have at least lasted for the warranty period. As noted before, Maytag was once the Toyota of w/d. You could not purchase a better product. Now, the exact opposite is true. Buyer beware, the most expensive with all of the bells and whistles is not always the best. My husband and I have gone retro with the purchase of a new Speed Queen w/d, which will be delivered this week. Hopefully, it will live up to the reviews that I have read.

We bought a Maytag Neptune Washer and from day one in 7/10/2004, we have had trouble with the washer and Sears. First, it stopped working within eight months after we paid over 1300 for washer and master protection agreement. We called over and over from that day and was told we didnt show in their system as owning one and that we didnt get the master protection agreement. This went on and on until they finally told us on 8/2010 that they finally did find us in the system and that the agreement had ended a year before and would send someone (that was on 8/31/10) to do the washer. After having sat for almost six years, it reset itself and worked that day. I told the guy from A&E that it was the computer but that wasnt what he replaced so the washer went right back on in a month. So we had to save to have someone else come out from A&E to charge us 143.10 to say it would cost a total of 310.51 for the computer and that it probably wouldnt work for too long.

Ten years ago I bought a very expensive set of Maytag Neptune Washer MAH5500BWW and dryer units with the single all-in-one pedestal. The washer starts sounding like a freight train during the fast spin dry cycle. A service tech came out, turned it on, listened, told me it is bad outer tub bearings going bad. And the price to fix is $846. Its essentially a throw-it-away deal. The tech says he has done hundreds of these and its a 3-hour major tear down, the bearings are press fitted and you essentially buy a new outer tub instead of replacing the bearings in the old one. Maytag went out of business and was bought by Whirlpool. What a piece of crap and to think how great Maytag once was. Now I have a dryer and a pedestal that probably wont fit any other washer brand.

Maytag needs to step up and admit that they have a design flaw in this dishwasher. The problem is that just a week or two after the warranty is out, it just stops working. Sometimes when you walk by it, it just turns on. No way to turn it off. Nothing works on the control panel. From what Ive seen on the internet, everybody is having the same problem. Its the control panel. It costs 180 dollars to fix, but it only lasts another year and you have the same problem. Ill have to say that when it works, it does a superb job. It just wont keep working.

I bought the Bravos glass top washer. It was always loud. I have a friend who had a cheaper model and his was loud too. My washer barely lasted two years before tearing up. It cost $85 to tell me it would be over $500 to fix it. I paid over $600 so it wasn’t worth fixing. Lid lock went out and gear went bad.

Okay, on March 2009, we bought this brand new microwave due to our major remodeling. We didnt move into the unit until February 2010, so the microwave was in its box for 11 months. After we moved in our condo, my husband and I had to travel for work for almost a year so our brand new microwave is very slightly, gently and barely used. Well, for the past 2 months, it had been acting up. Sometimes it heats, sometime it doesnt. For a 2 year old microwave, which we paid over $400, I would assume that it would last. It no longer heats up, so I called Maytag customer service to hear her tell me its not covered under the warranty and would cost $269 for repairs and there was nothing she can do for me unless I pay for a technician to come and repair it! No way, I swear it probably got used 5-10 times a month to heat up coffee for about a year. I am sure there are some major quality issues on this model because when I googled Maytag microwave, all I see is the same magnetic problems. I spoke to a group of my lawyers friends. If youre interested in joining a class act law suit, please e-mail me. I hate that people are being taken advantage of by these terrible companies. I cant believe how low quality their customer service and products are. Believe it or not, my $30, old microwave lasted me 14 years throughout my college years until we decided to replace it with the modern stainless steel one. It got noisier in time but not broken and still heats up just fine. This $400+ one lasted me only for several uses. Shame on Maytag, when I have time, I will be sure to write a complaint to the consumer department as well. I will dedicate my life in spreading the word out about their low quality product. Don’t buy Maytag unless you only plan to use it for a year or 2.

Purchased Maytag Centennial Washer and Dryer (MODEL MVC300VWI) at Home Depot 3 yrs ago. After 6 months, washer started to rust. Maytag told us It was not their problem. A 6-month old washer should not rust! Poor quality + poor customer service. Dont buy!

Ive had other dishwashers over the years. Ive had this Maytag now for almost 12 years and never had a problem with it. It cleans better than any others Ive owned. HIGHLY recommend the Maytag.

My husband purchased the Bravos XL washing machine less than a year ago at Bensons Maytag in Peoria, Illinois. Within months of purchase we noticed our clothing coming out with stains they didnt have prior to washing. After hundreds of $$s of clothing ruined we realized it was due to the fabric softener dispenser. We cleaned the machine multiple times & ceased using fabric softener. No luck.Today I finally had enough & called Bensons service department. The fellow I spoke with told me, You are not supposed to use fabric softener with the Bravos XL. I asked why a $1000 washing machine would have a dispenser you were supposed to use. He told me it was because people like to use it BUT you werent supposed to use it. I asked, Why would there be a dispenser if you werent supposed to use it. He told me the salesperson should have explained it during the transaction or I should have read the owners manual more thoroughly. I asked how I needed to go about correcting the problem & he told me to clean out the machine with really, really hot water. I explained we had multiple times.He didnt have any other suggestions so I asked about setting up a service call & requested he access my information so we could verify the warranty. He confirmed the unit was under warranty. I asked to schedule service & was told there would be a $50 service call fee. I told him, I would figure that would be under warranty to which he explained it would only be under warranty if it was the machine ruining my clothes. I asked, What other reason would there be for my ruined clothes and he told me if the laundry was being ruined because I used fabric softener it would not be under warranty. So I repeated that saying So you are telling me if the machine is ruining my clothing because I used fabric softener it will not be under warranty? and he got flustered and basically said he didnt exactly say that and they couldnt confirm anything until a tech took a look at the machine. I told him I would have to speak to my husband.So this is my question... why on Earth do we have a company building $1000 washing machines WITH A FABRIC SOFTENER DISPENSER if you are not supposed to use it? I have never, ever, EVER had a washing machine do such a lousy job. I have never, ever, EVER been afraid to put clothing in a washing machine... not even in a cheap, crappy laundromat. Shame on you, Maytag!

I purchased the most expensive stackable set available. After 3 years the Maytag Front Load Washer is dead. Wont turn on or receive electricity. It stopped in the middle of a cycle so I have an entire load locked inside. A repair person came out and confirmed $600-$1,400 to replace computer electronics. Right on the front of the machine, there is a shiny tag displaying 10-year Warranty. I live chatted with Maytag. Only the drum and some other ridiculous part is covered. She told me to call the 800 number to speak with a customer rep. After trying 2 times and being put on hold for over a half hour, I hung up. I WILL NEVER BUY A MAYTAG AGAIN!

I have always had faith in Maytag when it comes to appliances. As of yesterday, it is gone. We purchased the Bravos XL dryer in January 2013. Last weekend it was running, but not drying. We placed a call for a serviceman to come fix it. Discovered the heating element had gone out on it. We had to pay $300 for the repair. I am greatly disappointed a $1,000+ dryer is already having issues. Maytag should stand behind this problem and offer to pay for the damages, as from reading the reviews, it looks like this is an ongoing problem. Maytag should be ashamed of providing a product of such poor quality.

I purchased the Maytag metal interior two years ago, the very first year I had to replace the control panel board... Now, the panel went out again, after calling the Maytag executive office, they finally sent me the part, telling me I had to pay to get it fixed. That was just three months ago... Presently, the dishwasher has quit running water in the cycle... I will NEVER purchase another Maytag dishwasher... thinking you get The Best doesnt mean what you think... BEWARE...

We bought a freestanding Maytag gas range and oven two years ago for our lake house, where we stay approximately two months out of the year. The oven has been used probably six or seven times total. The gas range works fine, and the oven pilot light goes on, gas seems to be flowing, but the oven does not get warm. It registers 200 degrees, but there is no heat inside it at all. $300 to fix!

It seems to be a broken record with other reviews. I had a 2 year old microwave and the door doesnt recognize that its closed. Which means it wont turn on when I close the door. So you have to open and close it maybe 30-50 times and sometimes it works. I call Maytag who schedules a company but doesnt disclose anything about the warranty or service cost. I was thinking it would be a nominal fee since it falls under a 10 year warranty. The company calls and confirms the cost and I recheck with Maytag who said that the warranty only covers parts. So I buy a $300 microwave and have to pay $160 for a service visit because your company made inferior parts. Absolute sham of a company. Buyer Beware...

After purchasing this washer in 2007, the washer started to smell like sewage. At first we werent sure it was the washer and had a company come out to check the pipes. After this and calling Maytag complaining without any luck. We were told to buy affresh tablets and run it through the washer once a month. This last only so long and the smell comes back. Now when the washer goes into the spin cycle it sounds horrible. Again called Maytag without getting any resolve. I will never buy a Maytag again!

We bought our washer/dryer from Home Depot and felt Maytag was a good bet. Guess again. Washer is running fine for now but after light use (about 3 loads per week) dryer failed. With no warning, I heard a loud pop about 3 min into a cycle and overheating. If I hadnt been home might have caught on fire. Good for us we live close to a coin laundry so in no rush to replace but can bet when I do it wont be Maytag and thats too bad. One of the few makers still building in the USA but thinking Samsung is looking good. This is the Maytag 2000 series btw.

Bought refrigerator 2012 from Home Depot (model something like MBF1953YEB - how sad is it that I now have this number memorized?). Freezer too cold, refrigerator way too warm. Freezer air ducts frozen over. Tried manual defrosting twice per YouTube suggestions. Finally got repair for $400!!! Thats about half what I paid for it! One proponent repairman stopped me mid-sentence when I said Maytag saying, I know what it is. The computer (Jazz?) board needed to be replaced for $217. I just looked up Maytag to see it was bought in 2006 by Whirlpool. So I wont be purchasing any more Maytag or Whirlpool appliances.

Maytag Bravos XL washer and dryer. Best washer and dryer I have ever owned. I have owned about every major brand and these are by far the best. My husband is a hog farmer and the washer does a great job. I will always purchase Maytag appliances.

The range I have works awesome, which is surprising for an electric stove. For being 11 years old I am happy with how it is still holding up. The only thing I would improve is if it was a double oven instead of a single!

I purchased a Maytag gas dryer in November 2011. This is January 2012. I have got to use mine maybe 2 weeks altogether since I had it. It is to be repaired for the 4th time tomorrow. In the meantime, I have to go to the laundry mat to dry clothes, Maytag refuses to do anything about this. They say they are helping me by getting it repaired each time it breaks down. I want a new dryer. The retailer I bought it from will not stand behind this product either. You see these commercials on TV where the Maytag guy is sitting back and waiting on a call. Thats a bunch of ***! I have never purchased a product from anyone that they would not stand behind it especially for the 4th time in two months. I will never buy another Maytag product as long as I live and I will tell everyone that I know not to buy one either.

I purchased a whole stainless steel kitchen from Lowes and purchased all Maytag products because of the so called quality of Maytag. First we had to return the microwave because it was dented badly. We then notified Lowes that the door on the refrigerator cold cut drawer falls off when opening the drawer. Service man said he would send a new door. Same problem. You can clearly see that the drawer and the refrigerator frame is deformed. Maytag says that the warranty does not cover cosmetics. The range has a aqua lift self-cleaning technology that simply sucks. The oven does not clean! I recommend that no one ever buy Maytag products. They are the worst! I should not have listened to the salesman and bought what I originally wanted - SAMSUNG!!!

I reviewed lots of reviews, and decided that the negative reviews ones were sour grapes or uninformed customers! WRONG! Do not buy this washer. I replaced a 16 year old Frontloader Bosch! Should have had the Bosch repaired, but wanted a topload for a change, new look etc. From day 2 the washer began to squeal during the early cycle and at the end as well. Maytag repair was out for an unrelated repair on another appliance. I told the tech about it and he suggested its brand new etc, give it time to settle in.Now 4 months in and another service call to tell me its nothing!! It squeals so loud I can not run it while in the next room. I have videoed it and sent it to the Maytag repair in Glenwood Springs, and he said I should load it only full enough to see the impeller at all times!!!! Forget a full load of work clothes or a pillow or blanket. Which is to be expected to be able to wash. He said I needed to spread the clothes out manually along the outer sides of the TUB only, prior to washing the clothes! not over the impeller. I am not kidding! This is a open tub, so the impeller is the little thing in the middle on the bottom. I advised him, I videoed the event and even with three socks in it for a test it still squeals like a (well you get the idea). Trying to get Maytag help, but nowhere. Matching dryer door hinge broke first week, it has been repaired. Not good quality at all for the top of line Maytag. Then Maytag Man must be busier these days, than of old.

Control panel on front of dishwasher quit. Unit is 15 months old. Bought extended warranty through Home Depot. Took two hours on the phone to finally get to the correct department, they set an appt. for the following Wednesday between 10-2. Had to take a vacation day. Get a call from the appliance repair co. the night before stating they cant live by Depots schedule, they wont be out til the following Monday between 9-1. Schedule a vacation day. They come out then have to order parts, they wont be in for 7-10 business days. After 12 business days, I call back and they set appt. between 10-2. Schedule vacation day. They come out and the control panel the warranty company sent is the wrong one. Now I have to start the whole process over again. DONT BUY MAYTAG AND DONT BUY WARRANTY OR APPLIANCE THROUGH HOME DEPOT.

I have a Maytag fridge (model # 2258VEM4) which I have had for 4 years. A few months ago, it started leaking water on the floor and notice that it had a bed of ice on the floor of the freezer. Reading the list of complaints in this site for the same issue, it sounds like it is a design problem.

I bought a Maytag dishwasher (model MDBH945AWB3) in March 27, 2010 to replace a Kitchen Aid dishwasher that was only six years old and no longer serviceable. After a little over a year, its dead. When I try to turn it on, nothing happens. If I press the delay button, the lights come on, but in about a minute, they go off.

Please Do NOT purchase the Maytag Aqua Lift Gas Range. It does not clean anything, you will pay more money for a cleaning oven that does not clean any grease or droppings if you cook. This is not an Oven for any one, or family that cooks large meals or has gatherings. I had the technicians at my house over 4 times and they confirmed that this oven is not a self cleaning oven. It doesnt get hot enough as your self cleaning ovens. And MAYTAG did not want to hear anything, basically not clean much, but advertised as a self cleaning oven. Having been a Maytag customer for years I will never buy a Maytag product again. And we need to support American made, but not when the consumer is misled.

I bought as a pair the Maytag Heavy Duty Washer and Gas Dryer 30+ years ago The pair are like a Timex watch --takes a licking and keeps on ticking. They have never failed me and I have never had to call the Maytag repairman.

HORRIBLE. Dont pay more for substandard machines. Had a Maytag washer and dryer delivered on March 27th 2018 and it has been a nightmare to get it to start up. Now I have clothes stuck in there. I called Home Depot, you should never buy any appliances from them, they wash their hands of all responsibility once you sign for it. Called Maytag. On hold for almost 10 minutes, they only have 2 certified repairmen in the area 0f 600,000 people. Will be 5 days until they come to look at it. I told them I wanted to return it for a GE or something else. They said I had to contact Home Depot yet Home Depot told me it was Maytags problem. SAVE YOUR MONEY!!! MAYTAG IS NOW AN INFERIOR PRODUCT WITH EXTREMELY INFERIOR SERVICE.

Our problem started when the control lock button locked itself on. Called Maytag and told it wasnt covered by warranty but they did walk us through resetting the power and it fixed the problem until we ran the next load. Now when you try and set it, the rinse only light comes on. Bought the Maytag because I always believed them to be dependable - wrong!! I had a basic model Whirlpool running for a family of 5 for 25 years prior to this Maytag without ever having to call a repair person. Maytag wont deal with the issue so I would recommend to anyone else having any issues with unreliable appliances to do what I am doing - boycotting Maytag!!

I purchased this high-end dishwasher 7 years ago and 3 years of fairly light use, the control panel on the top would operate sporadically or not at all. Called the dealer who sent out the repairman that installed it and had to replace the control panel to the tune of $300 once the labor was included (took 2 visits as he had to order the part, so 2 trip charges). Now 3 & 1/2 years later, it is doing it again!! A call to Maytag and then a transfer to Whirlpool customer service got me nowhere. They said there were no recalls or documentation for problems with the dishwasher. Really??? I see lots of complaints on this problem with very similar Maytag dishwasher models. They would not send me a new part at no charge as a result but offered to set up a service appointment for me so I can spend another $300 (probably higher now after 3 years) and would register my complaint. Thanks for nothing!Doing that would turn my originally $900 dishwasher into a $1500 one with the result that it will probably fail again in 3 years. Absolutely ridiculous customer service. I saw a YouTube video on taking it apart and applying silicone around the ribbon connections as others have done in the hopes I can get it working again for a while as I dont have the $$$ needed to replace it again on a retired fixed income. :(

This is the most horrible washer ever. Within 3 months it would not go beyond sensing mode and never fill or wash. Tech came and fixed it... 3 times. It still happens and I have to jiggle it all around to activate it. Clothes are never clean, dog hair is never washed out... My broken old agitator machine was taken to the dump & I wish I had it back! How do the stores give this machine a good rating?? I cant do light quick washes, I have to wait forever... Our water bill is 2x higher than ever because if I dont fill the tub with deep water, the clothes dont even all get wet. Hate, hate, hate this thing.

We bought this Maytag MFI2269DRM01 Fridge/Freezer in June 2016. We have nothing but trouble. First the center rail holding up the Fruit/Veg drawers snapped within a month then the freezer drawer would not close properly which gave us all sorts of problems (door open lights flashing and fridge staying on longer. Lights not working etc.) The service tech came out and tried to fix it and went away saying it was not repaired that he would need a new freezer drawer. In the meantime I had to push the drawer to try and get it to work right. Now the handle is loose and the stainless steel front of the drawer is damaged by pushing it in so much.This repair started in November and now it is the end of March. I asked them to replace the complete unit but they say that the warranty is just to repair. It seems like they have no parts to fix this. Then the new center rail snapped again!!! When they sent the part out to me to install, I found the main frame of the Fruit/Veg rack at the back had snapped. Everything is brittle plastic with not enough support. (The only vegetable that I think I can put in the drawers is mushrooms.) I thought by buying a Maytag that the name sold it. What a piece of junk it is!!! Will never buy another Maytag product!!!

Bravos mct. Unbelievable, this washing machine is terrible, no water. The water level doesnt even cover 6 items. Have to wash triple the loads of my old washer just to get the clothes clean. I have to go to the laundromat twice a month. I shouldnt have to do that. Almost want to fill the washer with water, but dont know what will happen. Very unsatisfied with this washer.

We bought the Bravo XL set 11 months ago and the washer leaks all over the place.. Called Maytag and had the repairman show up. Upon arrival he told us these were the worst machines to buy and would never recommend to anyone. He also said that business has been great due to all of this.. He checked the washer and said the water pressure was too high and lowered it. He couldnt find anything wrong with it. After he left I started a load and sure enough it was the same. Called him right back and he said to call Maytag because he was going to another repair job. I called Maytag again and they said to call the repair guy.. Never again will we ever buy Maytag.

Do NOT buy a Magtag washer. I purchased a brand new washer from Lowes in 2017. The washer gets stuck in the wash cycle. When I called Lowes, they said to call Maytag, who sent a service person out. The service person recalibrated the machine never ran a cycle and left. We had to call two more times after this for the same reason with the same result where the serviceman left without running a cycle. This was all while the product was under warranty. Since I had three service calls, I called Maytag frustrated that this kept happening to a new product. I was told there was nothing they could do, but if it happens again to have the service guy come back out. When the warranty runs out, I will have to pay for the service tech. Unbelievable. Save your time, money and frustration and buy a Whirlpool! I dont know how Maytag gets away with selling defective products.

Since the day the Neptune washer and dryer were installed, the washer has given me nothing but problems. It vibrates so badly and dances all over the floor.I have had the repairman over at least seven times and, now, it is out of warranty so I am spending my own money. The last service man was from Hurst Appliances in Regina, SK. He removed the pedestal to see if this might be the problem. He also sold me some foot pads for $50 that he said might help the problem. However the machine is still vibrating and the terrible mold smell comes out of it as well. I am thoroughly disappointed in this product. I will never buy another Maytag product and tell my friends not to as well.

Not only is the dryer junk, so is Maytag support and service. I have owned this dryer for 2 years; my previous dryers lasted about 20 years each. This one is on its 4th service call, none of which are apparently under warranty (well, except the first one). From what the techs who come out here tell me, the design and build are both poor. I will never own another one of these; if I can stretch it out one more year, then well replace it.For now, the drum wont turn. There is a nylon support bushing (and possibly more) that degrades immediately upon use. There are only two of us, with about 3-4 loads per week. This was supposed to be Commercial Technology. The only thing commercial about it is that you have to rely on commercial laundries to get the drying done. It is good that the drum has a 10 year warranty - it will make a nice planter out by the front gate.

We bought our Maytag Bravos in December 2010. Four months out of warranty, like many other complaints Ive read, we started getting the loud jet taking off noise from the laundry room. Now we are having issues with the lid lock not allowing you to get to the clothes. This machine tries to spin three times and then locks up. It literally locks the lid and will not allow you to get to your clothes! For a machine to fail just four months out of warranty is a joke! After investigating the problems with the machine, it will cost us more to repair than what we originally paid for the washer in the first place. Give me a break! There should be a recall and Maytag should have their feet held to the fire to replace these less than adequate high-dollar machines!

I bought this dishwasher from Sears on Tuesday July 15, 2014. It was delivered on Friday July 18, 2014. On Friday July 25, 2014 two plastic clips that hold the top rack on broke, and one whole side of the top rack fell down. I called the 1-800 # in the book. Then I called the repairman they recommended. He came out on the Monday July 28, 2014. By the time he got here, the clip on the other side broke. Now the rack was hanging by one plastic clip. While waiting for these parts, the last clip broke and the rack was completely detached. So he received the parts on Friday Aug. 1, 2014. When he arrived, lo and behold, they sent the wrong parts. He had the side tracks that hold the rack, not the cheap plastic clips that attach it to the racks. So I have had my new dishwasher 14 days, and have been able to use it a total of 4 times before it failed. I am now awaiting the new parts. The parts that broke are made from a cheap thin plastic, and this is expected to hold up the entire top rack and the dishes its holding.

Maytag Bravo XL -Model MVWB88OBWO. Washer quit after 13 months of light use. Repairman came, $148.00, worked on just a few setting for 4 loads. It has a bad controller and some other part. Total cost of repair, if I was stupid enough to make it, $650.00. Guess whats going to the trash. I guess that kind of negates the ECO-FRIENDLY, huh? I will NEVER own another Maytag appliance.

Under no circumstances should anyone buy an MMV4205DE or maybe any Maytag microwave. These units contain defective door switches and will fail within a year rendering the unit useless. The engineer that got the bright idea to protect us from starting the microwave without opening and closing the door along with the engineer that designed the defective switch scheme should be fired immediately.I purchased the unit March 2016 to replace a 10-year-old Maytag that had a failed magnetron, no problems ever with the door switches! This unit started to act up in Dec 2016 with the fatal open/close door problem, I am an EE so I opened the unit and checked the switches and found they were defective, replaced both for $80 and 6 months later the problem is back. I am buying another brand as I dont have time to deal with the problems with this unit. I now have the old white 15-year-old unit that I replaced years ago sitting on the counter to use while another unit is on order. Unit is heading for the landfill next month. Never buy a Maytag microwave, they all have the same problems!!!

I spent extra money on a commercial grade Maytag dryer $1300 before taxes because it had a 10 year warranty. The motor and drum quit - and Maytag refuses to honour the warranty. I am appalled by their dishonesty and lack of integrity. I do not recommend them to anyone.

Washer Bravo MVWX655DW0 - Maytag has shipped the wrong part twice, sent me the right part which is faulty and the 4th one arrived today. I have not had a washer since 9-16 October 9, 2017. I am writing to tell you about my experience that Ive had with Maytag over the last 30 days. I have owned several Maytag and Amana appliances in the past; along with owning several currently. Over the years, weve had a wonderful experience owning these appliances however the last 30 days is one that has been unbelievable. On September 18 on a Monday early in the morning I called Maytag service line. I spoke to a young lady who had difficulties finding me in the system and did not know how to make an appointment to have a Maytag repairman come to my house to look at my washer. I did not take down her name as I thought and trusted that the company was acting on my behalf and would take care of me.I spent several minutes explaining to her that I did not live in Indiana that I lived in Iowa and that I would need a repairman who is close to my hometown. She continued to give me phone numbers with area code 407 in Indiana and then kept repeating some type of a ZIP Code 49 something for Indiana. I explained to her four different times that the zip codes in Iowa start with a five and the area code would be a 515 number in the area she was looking at. She finally gave me two phone numbers, one that did not work. I asked for a repairperson out of Jefferson. She told me Cranston Repair and gave me the phone number. She told me to call him. I told her that I would go with the Cranston repair since Jefferson with my hometown and it was close to where I lived.I then asked her if she would make the appointment. She told me she didnt know how to make the appointment and she kept messing up with the system. Not sure if it was her first day or not but that was fine so I said “never mind I will set the appointment up myself. I then asked her to double-check to see if our new Maytag refrigerator that we just purchased was registered. She told me she did not see it but all I needed to do was call back the next day with the model and serial number and anybody I spoke to on the phone could go ahead and get that registered. I thought I had registered online; I only wanted to double-check but she didnt see it so I assumed I did something wrong and then would make the call back the next day.I called Cranston repair and scheduled an appointment with the repairperson for the next day Tuesday, September 19. Repairman came the next day on time, looked at the washer and found that the transmission had gone out. I had purchased the washer just shy of two years ago. The repairman said that he would have to order the part and would let me know how long it would take and would return to fix the washing machine. He called from my house and was told that the part was on backorder until October 5. After the repairman left the house I decided to call Maytag back and express my disappointment in the product as Maytag says they stand behind their products and the fact that it was not even two years old and that a transmission would go out. The individual I spoke to this time, Antcwaniqua? Not sure about spelling, listened to my story. She also told me the part the repairman ordered was not correct.I needed part W1 1132267. She said that was a substitute part for the correct part that I needed which was W11035204. I told her that the part number ending in 204 we were told was on backorder until October 5. She said no, the part may show that in the system for repairmen but Maytag can locate the part in a warehouse, it would be shipped in 3 to 5 days. I told her that he had called a place in Davenport, Iowa. What she would do because of all the issues I was having was she would go ahead and ship the part out to me at no cost in 3 to 5 days.I wasnt sure about that warehouse thing. It didnt sound convincing but at that point I had to go along with it. What was shipped out to me was the substitute part W1 113-2267. At this point she told me that I would have to pay to have the part put in; I agreed to that on I want a new washer or I want my washer repaired within 72 hours at no cost. I have not had a washer for 3 weeks plus. Repairman in coming Friday and I am not confident that the 4th gearcase part that came today will work either.

Purchased a Maytag OTR microwave in May of 2017. Started having issues with the Open/Close Door malfunction by September. Repair came out and essentially told us to keep opening and closing until it worked. It is January 2018 and the issue has gotten worse. My question is, since Maytag is keenly aware of the problem and has for years, based on other reviewers on here, why hasnt a class action lawsuit been filed? These appliances are expensive and it sounds like many of us have been taken to the cleaners!

I bought this machine at Lowes because of the BIG drum area and about 2 years ago, it started to make funny noises; then I got the F-51 signal. I tried everything, shifting articles of clothing, then unplugging the machine and re-plugging. I am in the process of researching a plain Jane model, not one with all the bells and whistles. I am extremely dissatisfied and wish Maytag would step up to the plate and recall these machines. A motherboard and the costs for other parts, I would be better off replacing with a brand new machine. Dissatisfied!!!

Purchased Maytag front load washer model MHW6630HW from Home Depot. Machine was installed 9/15/19. From inception we had issues that have escalated. Machine leaks and makes strange hissing sounds. Home Depot has no record of the purchase in their website now. We tried to return it within days. We contacted Home Depot executive offices and they keep sending Paradise Appliance repair. The repair people do nothing and keep saying we have to come back again for you to be considered for replacement. Home Depot is dragging their feet and we are concerned about the six month deadline. The Maytag does not do an effective job washing and clothes comes out wrinkled. Concerned about the sporadic leak getting worst and doing damage to floors.

Purchased my Maytag Bravo MVWX500XWO 4 years ago. While still under warranty I had to call for service once. I felt based on the Maytag reputation I didnt need to extend the warranty. WRONG!! My Maytag first started with the loud and fast spinning. Like it was about to explode! Then my washer started leaking. I thought I was having plumbing problems, so I called a plumber... wasnt the plumbing. My washer wasnt draining out completely so I finally called an appliance repairmen who immediately knew what the problem was ($109.90) for a 15 minute review. The leak was from the bottom of the washer... the seal around the transmission cracked, broke or whatever causing water to drain out in my garage. Also the main control board wasnt working. Repairman said it would cost me $700 to repair!! Really?!! My machine was practically new! Without hesitation the repairman said for me to call the Whirlpool/Maytag 800 number and they would offer me another washer for 50% off at their online outlet. Repairman said this always happens... Why would I want another Maytag or Whirlpool!! Please do not buy the Maytag Bravo... Can you imagine if this happened with a car purchased... 4 years and then having to buy another car??!! Not reliable or worth your money!!

Almost one year to the date of purchase, my Maytag glass top range stopped working. The oven is still operational, but the range top does not work. The knobs turn and the surface lights go on but the elements no longer heat up. Trying to get a response from a real person at Maytag was impossible. I was put through a myriad of prompts that led me to scheduling a service appointment. I called AppliancesMart and got a wonderful sales person who said a service call would cost me 60 to 80 dollars and that he had not heard of repairs below $300 for this type of problem. Needless to say I am very angry and disappointed that I had not done more research before I purchased this item. If I can prevent one more person from making this same mistake, I will get some modicum of satisfaction out of this horrible experience.

Im living in a shop lot area and its near a university school. It has different laundromat stores here, and the cheapest is the one who have Maytag washers. So Ive been going there to wash clothes and as time passes, I noticed that the clothes have been getting stains after washing and these stains cannot be removed easily. Ive read reviews about clothes getting stained using Maytag washers and I cant believe that it happened to me. I dont know whats with Maytag that makes the clothes dirty/stained. I went to other laundromat stores that are not using Maytag washers. Its quite expensive, but it really makes your clothes clean.

The washer that always needs repair! My first problem with my Maytag washer was that the sensor needed replacing (wont wash or spin). Since then I have had the sensor replaced and motor replaced. Today, I had to call for a service call, and was told that I have to wait over a week! Bad customer service!

My Maytag refrigerator (bottom freezer) is about four years old now. Since the first year, it has been freezing up. The refrigerator gets warm and the freezer stays cold. Two repairmen have looked at it, replaced the electric panel and the thermostat - neither repair fixed the problem. If you completely defrost it, it will start working again. For about three years, it would work for a few months, but now it will only run for about two weeks before freezing up again. I called Maytag when this first started happening and again recently. They say they have never heard of anyone having this problem and they are sorry. The woman said she would put my complaint in my file. I certainly would recommend that people avoid Maytag refrigerators.

There should be a recall. Just look at the number of people complaining about this same exact occurrence about the control panel not activating. Im on my second control panel in 24 months. Some people are on their fourth already. Give me a break. There needs to be a recall and a redesign of this thing, which turned out to be a piece of junk washer.

The machine will not fill with enough water to wet all the clothes. I have to tape the tub to trick the machine so that the clothes will all get wet. When I had a service look at the machine he said that is how they are designed to be energy efficient. Who does not getting all the clothes wet clean them??? This is not for big loads but ALL loads - even hand wash loads. Every load takes an hour plus. Less water, more time, unclean clothes. I lose all the way around. REALLY wish I had a machine with the old features.

The washer is designed to use low amounts of water. The top is glass so you can watch what is or is not happening. The manual states there should be clothes above the water after filling. However after the wash cycle with a full or even half full washer, there is still some dry clothes above the water. As a result the clothes are not washed until the rinse cycle. I called Maytag and a repair tech came out to fix it. His solution was to trick the sensors by dumping a pail of water on top of the dry clothes before starting the washer. The sensors think there are more clothes than there really is. Will never buy another Maytag or Whirlpool product again.

Before putting clothes in dryer you have to untangle them. Sweaters and even t-shirts become stretched beyond help. Clothes smell like mildew if you leave them in the washer even just a couple of hours. Im 50 and had a few washer/dryers and these take the cake. Ive used the washing machine cleaner/refresher (something I have never done on washers in the past) and still a mildew smell. The dryer has lint on both sides of the lint screen. And as stated before if you dont untangle your clothes they come out in a big knot, partially un-dried & very wrinkled. The lint on both sides of the screen concern me - Ive never had a dryer do that before. Its not much lint on one side but enough to think something is not right.

Bravos XL - This machine purchased in 2014 at Home Depot service plan, needed major repairs just over a year old. Tech working on this machine replaced the whole tub assy after Maytag want to just do the cheap repair and just do a bearing kit. Reading online all the hundreds and hundreds of the same complains Maytag has done nothing in good faith to replace these junk washers!! My washer is now leaking under the washer less than a year after the last repair!! My good friend purchased the same machine and has had the same issues and his has been down for weeks because the poor service person from Maytag service broke some of the new parts! Now the washer is leaking again. WHAT can be done. This not right!!! Public needs to be warned about these flawed machines and Home Depot is still promoting these Junk machines!!!

Had it for over ten years, had no problems. We dont use the oven too often but it is simple to operate and has served us well. Easy to clean, stainless steel like looks on the front goes well with our other appliances. Reasonably priced too.

Dishwasher control board - This will be the 3rd time for this same failure with the start/resume button on control panel. Obviously, with all the complaints regarding this part indicates manufacturing is producing a defective or inferior part. The service provided by Maytag, which is supposed to be a reputable company, is a joke and non-existing. Like many others, here I will gladly be part of the class action suit and will never buy another Maytag appliance and will also inform others of their poor service.

The washer does not wash good on the initial wash. I have to wash my clothing twice. Cost and time consuming. The washer is “HE” and the water level is never enough. My clothes be saturated with dirt/lint scum and I never overload my washer. HELP!!!

Its about Maytag MDE7600AYW Atlantis electric dryer issues, Nov 2005 model. There is an obvious design flaw. I have replaced the automatic dryer control board twice since 2005. The unit simply never shuts off, or cooks your clothes for 2 hours. Who will recall this unit and fix the circuit? They will not admit their error.

Echoing the sentiments of others on this site, I am deeply disappointed in Maytag brand appliances manufactured by the Whirlpool Corp. When, for the first time in my life, I was able to buy all brand new kitchen appliances, I didnt even consider any other brand but Maytag. This was based on many decades of using Maytag products and watching my mother use them. I come from a big family so our appliances got used hard, and the Maytag brand ones worked year after year, decade after decade with little or no maintenance. To put it quite frankly, my new Maytag products are junk. I could supply a whole laundry list of problems but, in the interest of space, will just tell about the latest. A couple of weeks ago the fake tin foil paint on my oven and burner knobs just started falling off, revealing cheap plastic underneath. When I called Maytag to complain, I was asked how I clean the knobs. I told them that when I clean the stove front I remove the knobs and drop them in warm water with a couple drops of Dawn dishwashing liquid for the few minutes it takes to clean and polish the stove front, and that I had been using this same procedure for 2 years. The rep. hemmed and hawed awhile and then went away to consult her database. When she returned she told me that one is not allowed to soak the knobs per the manual, and therefore she could not offer any help. She then generously offered to transfer me to the parts department, where the rep. informed me that replacements would cost $70 EACH, thats a total of $350 plus shipping for 5 cheap plastic knobs. WOW! What a deal! I tell everyone I meet NOT to buy any Maytag branded product, and to apply extreme skepticism before considering any Whirlpool product. (BTW - the last certified Maytag appliance repairman to come & fix one of the appliances essentially admitted they are junk.) Model #: MGR8775AS SN: R32810432.

It is nice to know that there are other people out there that have the same problem with the Maytag washers cabinet inside and outside rusting. Our rusting is around the bleach area rim and on the outer seam of the washer. Our washer is now 4 years old. We started having the rusting problems in 2011. We called Maytag and of course. They are sorry for our problem but cant do anything about it. They made it sound like we were the only ones having this problem. We need to stand strong and continue to complain about this problem until Maytag takes responsibility for their poor quality washers. Anyone out there looking to purchase a washer. Do your homework. Buyer beware of Maytag washing machines!!!!

Bought in July 2014, third service call already! To replace my 6 years old Maytag Centennial thinking I was doing a good thing to upgrade to an HE... HA! Jokes on me! Washing machine: Water level. How can you wash clothes in 1 inch of water??? Noise. Very noisy at every cycle. Shakes and easily unbalanced. Clothes are still dirty after wash (obviously if not enough water). Dryer. Noisy with sporadic blower sound (like a plane taking off - high pitched). Three service calls in 6 months??? 2 calls for cable suspensions and now waiting over a month for the tech to change the drum completely. Good thing that I took an extended guarantee, for an extra $300.00!! After Ive read the over 400 complaints about this product, I really feel like I got screwed! My last Maytag EVER!

My Maytag dishwasher model MDB7749SBM2 was two months out of one year warranty and the Whirlpool control panel went out. We replaced it for 80.00. 3 months later same issue. We had that replaced for free. 4 months later same issue. We had to fight but got that replaced for free. Now 2 months later same problem. It cleaned wonderful when it worked. I will never buy another Maytag or Whirlpool. I used to buy nothing but Maytag. We threw it out tonight. Tired of a dishwasher that is only part time.

I purchased a Maytag Centennial - HE Energy Star Washer from the local Home Depot on Guam.... Probably the worst clothes washer I ever purchased. I typically buy a Whirlpool brand for many of my appliances of which I have always been satisfied with the products. I understand that Whirlpool is now the new principal owners of Maytag. I bought the Maytag for my new second home which I have moved into as my primary residence. Great ads on TV that promote the Maytag product line but the product fails miserably in performance. From the day I purchased the washer, my wife, kids, and I visibly noticed the laundry doesnt get as clean as my previous washers, it takes longer to wash a load of laundry no matter what is the preferred setting, the irritating hum is deafening in my laundry room, now the washer has malfunctioned and doesnt cycle through properly, leaving the clothes either unwashed or wet... I do not know who is your servicing agent or center on Guam and I am debating to repair it or just dispose of it. I can tell you now... MAYTAG... NEVER AGAIN. Now I know why the Maytag Repairman is so lonely.... I wouldnt bother to repair it. I hope these issues do not filter down to your Whirlpool products. That Samsung is looking pretty attractive right now. I bought one of their dishwashers that is doing a pretty good job right now.... Guess what? There was a Maytag next to it that I didnt even look at.

Bought a new Maytag dishwasher in July 2013. In December it quit working and the problem was the control panel. The service tech knew automatically what the problem was when he arrived. It is now May 2014 and the control panel has gone out again. Contacted Maytag and was told they will extend the warranty another six months from the original warranty. After reading that this has been offered to others with mixed results I have my doubts on whether it will be honored. This is our last Maytag appliance.

Our Maytag microwave, which we bought based on Maytags supposed quality, is nothing but a piece of junk. In two years it has had or needs repairs that nearly double the original cost! Thats ridiculous. We are done with Maytag and are not going to get suckered into their Whirlpool/KitchenAid or other brands. So long.

We just had the same problem as most of you have posted. The control panel malfunction. Model MDB7749SBM. Our issue started after only 18 months when the dishwasher would start on its own and/or cancel a wash on its own. I think this is a major issue if a home appliance can start on its own from the off position and run through multiple cycles. I think this could be dangerous if you are out of town. Our cost to replace the panel was more than 1/2 of the original purchase price. This is a major defect and should be handled by Maytag if they are a company with any integrity.