I purchased my Maytag Bravos washer and dryer in July 2007. As with any appliance, we always purchase the extended warranty as it usually runs about $100 on appliance. My first experience with problems was in February 2010 when the control panel went out. If I had not purchased the extended warranty, I would have been in trouble. It ran out in July 2008. It was downhill from there. In September 2010, it quit spinning; and the fabric dispenser would not work. I called again in September 2010. The tub was out of balance. In June 2011, the panel control went out again. In November 2011, it would not spin. In June 2012, the panel for control had to be changed out again. In July 2012, now the pump is leaking. And guess what, my extended warranty is up 8/1/2012. I contacted Customer Service, which said unless there was the same problem within 12 months, there was nothing they could do. Well, Im fired up. I intend on making a complaint with the Better Business Bureau and anyone else who will listen to me. I paid over $2000 for the washer and dryer, and it should last more than 5 years. This is ridiculous! When Whirlpool bought out Maytag, then the product went to crap! Dont tell me the Maytag repairman does not have anything to do now, because I know I keep him real busy. I am so tired of the companys just blowing you off when you work hard for your money and purchase a product for your family that should last at least 10 years. I am a principled person, and this is not going to go away easy. The repairman is coming next week to fix it again. I am going to give him an earful as well. The last one who came to change out the panel board (3rd time) said they had nothing but problems with this unit. Well maybe they made it that way, so when the warranty runs out, they can charge you an arm and a leg for the part and the labor to repair. I will never buy a Maytag product ever again. My next one will be the new LG washer and dryer. Talk about the lemon law. This product from what I am reading here should very well fall within that category.

Maytag Bravos Washer 300 Quiet Series Model MVWB700VQ0 - Nothing about it is quiet. Worked pretty well the first year. Spin cycle works too well. It twists and rips. The second year it needed a new pump because a dime got into it and cracked the pump. When you wash anything bulky you better sit and watch it because it will almost certainly go off balance. Year three Sd (suds or slow) code started flashing and washer stopped half way through. Not sure why suds because I only use HE Tide, no perfumes or dyes due to my daughters sensitivity. I use Affresh as directed and on schedule. Was told it was a slow drain, found two dimes in the filter and a lot of lint. Still not working and flashing Sd... stops half way, agitator moves left to right doesnt spin. When the diagnostic was performed, the basket spun but when it stopped it made a grinding noise. Now it might be that it needs new bearings! So much for the Maytag reputation. Its junk and I will not be buying another Maytag, Whirlpool, Kenmore or any other product from their affiliates. Not purchasing anything from Sears again either. Also I will be canceling my subscription to Consumer Reports because they highly recommended this product. Shame on Maytag. How do we start a class action suit?

I purchased a Maytag Neptune 24” front load washer (MAH2400a) and 24” electric dryer (MDE2400AYW) on October 26, 2005 from Sears in Chesterfield, MO. In April 2011, the drum in the washer began to slush and grind. Water also began pooling around the machine. I called Sears and arranged for service repairman. Before he even looked inside the washer, the repairman wanted to give me a coupon for $50.00 off a new washing machine from Sears. After my insistence, he finally opened the washer and told me I needed a new drum. Because of the Sears repairman’s reluctance to look at the machine, I had another appliance repairman review it and was told that the water pumps for this model were defective. Any loose items the size of coins collected inside the pump and damaged it. I paid $340.00 to get the pump replaced. Ten months later, the dryer started smoking. After scheduling a service call, I was told the heating element burnt out and it would cost $360.00 to replace. It was then I noticed that the washer was leaking again. I took the front base cover off and saw mold growing under the machine. A little research uncovered that this set of machines has had many dangerous problems, from mold to catching on fire. There was a class action lawsuit filed and won by consumers in April 2005, yet I was sold this model in October 2005. I feel both Maytag and Sears knowingly sold me a defective and dangerous product. I would like to be refunded for this set.

I purchased my Bravo (MVWB300WQ2) washer a little over two years ago. It took all day to wash some loads due to leveling problems. Example, you could not put more than two bath towels in at a time, even with the towel setting. The washer would stop and you have to re-position the towels. You cannot leave because it stopped so often. Also, the washer makes an extremely loud noise during the spin cycle. My most recent problem, it does not complete the spin cycle. My clothes are still very wet. I refuse to call service. Its just too costly. It would be the third time in less than 3 years. However, the first time was within the year warranty (no charge). The basket had to be replaced - it was ripping my clothes. During my second service call, the technician advised me in purchasing an extended warranty. I paid for the service call and for a one-year extended warranty which just recently ended. The washing machine is not worth paying for service again. I am going to purchase a new machine instead!

Bought this machine summer of 2018 when my old washer went out. This machine is impressive looking but that’s about it. Clothes don’t get clean. Half the time they don’t even get wet! I’ve had to wash sheets two or three times to get them clean and wet. When washing jeans there is always lint and white debris on them when the wash cycle is done. I’ve tried all different settings, I’ve tried different detergents always the same problem. Wish I’d never laid eyes on this model at Lowe’s last summer. Gotta say, worst purchase of an appliance I have ever made. Don’t waste your hard earned money on this piece of junk!

The control board is not working on my 2 year old dishwasher. I now see this is a common problem with Maytag dishwashers. I have called to see if there is a recall on this problem and they said no. I have been told it can cost up to $500 to fix it so I guess it is a throwaway. I should have called when it was purchased as the digital buttons didnt seem right from new. What a waste of money and I will never buy Maytag or Whirlpool.

My husband and I bought a Bravo XL washer in the fall of 2015. I certainly wish we had read the reviews on this site of this product. We would have saved ourselves a lot of money and grief. This machine does not clean clothes and actually damages them during the spin cycle as reported by others. This low water no agitator technology does not work on a top loader. Stuff doesnt come clean! Im not sure what we are going to do but we learned a valuable lesson the hard way. We purchased this machine in September of 2015 and are unhappy with it!

Maytag Bravo Washer and Dryer - We are usually review writers. I just felt it was our duty to help others save their hard-earned dollars and not purchase this product. We have owned this expensive and highly researched set for a bit over 2 years. We have had to have repairmen out a half dozen times for dryer repairs. The washer was purchased with the largest tub because I wanted to be able to wash a full load of sheets or a blanket. NOT!!! It gets off balanced, twists every single item (as in blue jeans, towels, soft t-shirts, etc...any weight or size) into a huge mess and has actually ruined some of my clothing. The dryer gives me error messages all the time. I am beyond words with my disappointment. We saved a long time for this set and now are absolutely stuck for a long time before we can replace. You know Maytag my message to you is that hard-working people used to trust your company name. I have been married 43 years and we keep our purchases for many years. I have never in all these years been so disappointed in the huge purchase we made thinking it was a lifetime investment. Now I am doing everything I can to save this year so maybe can replace it down the road as soon as we can. I am telling you people reading this... DO NOT BUY THIS SET. IT IS A TOTAL WASTE OF YOUR HARD EARNED MONEY.

Like so many others, I now discover, we are having a ridiculously frustrating problem with our Maytag dishwasher, bought one and a half years ago. Last week, the control panel stopped working -- we press normal and a whole bunch of other lights come on; try to press other cleaning options and entirely different ones light up again. Sometimes we can get it, with luck, to quick wash or super clean and thus have our dishes cleaned (which the machine never did that effectively anyway); sometimes we cant. I havent called the company yet, but given what Ive read, Im unsure if it would do any good. Judging from all the similar comments, Maytag is clearly selling a radically inferior product and care nothing much about this. We will surely never, ever buy another one of their products.

On Nov 1, 2018 - 14 months after purchasing this top of the line refrigerator - the compressor broke and the freezer stopped functioning. I called Maytag Service who said the soonest they could repair it was Nov 12 - 12 days after it broke. Also they said my 10 year warranty didnt apply unless I had proof of purchase. I said I registered my product online when I bought it but they said they had no record. So they had to charge me full cost of service and parts which would be $1000-$1500.I then called LOWES SERVICE ADVANTAGE - I really like Lowes by the way - and they verified my proof of purchase and that in addition to the appliance warranty I have a 5 YEAR mechanical parts repair warranty through LOWES. Thank goodness I purchased the service warranty from LOWES because Maytag was NOT honoring theirs! So then a repair person from FAST APPLIANCE REPAIR INC came to fix the refrigerator and said because it was the compressor he couldnt repair it so I had to wait a few days later for the COMPRESSOR SPECIALIST to come out. The compressor specialist came and said he didnt have any in stock so had to order one.Six days later - Nov 19 - the compressor arrived at my house. I called FAST APPLIANCE REPAIR and asked for someone to schedule an installation. I said Im RETIRED and can do it any time. They said the soonest they could install it is NOVEMBER 28 - ONE MONTH AFTER IT BROKE. So now Ive lost two large drawers of frozen food that spoiled. I have no refrigerator this week for my birthday and for Thanksgiving. I have to wait another 9 days to get it fixed. I am NOT HAPPY. I am sharing this experience so anyone considering buying this or any other MAYTAG product will think very carefully before making their purchase. Also, be sure to buy from Lowes and get the Lowes service plan for any appliance. Ill try to update this if and when my refrigerator gets repaired.

Maytag French Door Fridge Model MFT267AEW10 - Not even 1 month out of warranty and the water line solenoid is leaking. It seems the water line installed at the factory was pulled so tightly that it has caused the solenoid inlet to start leaking. We really researched this refrigerator and thought we were buying the best. Not so, Maytag wont warranty it. The last purchase of Maytag I will ever make. We should have bought the Samsung but we were trying to buy American. Wont make that mistake again. Not a smart investment. Refrigerators are supposed to last a good ten years. How sad.

The washer machine is only 2 years old and its broke, at first it wouldnt spin and now it wont wash. Everyone is saying between the parts and service fee, it will cost 200 to 300 dollars or more to fix, most technicians wont repair them because they say that we may as well cut our loss and just buy a new one. No one likes these machines. I wish I would have known what a sham the washer machines were before purchasing.

I bought this washing machine 2 years ago or so. We have always bought Maytag. My mother still has hers she bought over 25 years ago and it still looks and works great. So my wife wanted a new washing machine so I said were going to get another Maytag. Boy did I screw up. What a piece of ** junk. Sounds like its grinding gears all the time, so loud. I close the door in the wash room and I can still hear my investment on a Maytag grinding my nerves because I spent so much on a product of a brand Maytag that I thought would be around for a while. Do not buy a Maytag.

I love it. It has a big tub. It has no agitator. It uses a lot less water. Many cycles.perfect machine. I would recommend this to everyone. Also top loading. Would never get another front loader. They arent worth it.

The Maytag dishwasher works really well. Not the quietest, but cleans thoroughly. I dont use heated drying though, to save energy. Stainless steel interior retains enough heat to mostly dry. However, unit died after only 7 years. Expected longer life.

At 36 months old, my Maytag refrigerator has already suffered from a Freon leak. After repair, the leak continued causing the fridge not to produce ice. After another Freon charge 7 days later, the fridge will freeze ice only in a manual ice tray. The water in the ice maker for whatever reason will not freeze? To make matters even worse, the freezer fan has been noisy for the last year. Maytags solution is to purchase extended warranty for $300 plus or hire repair person at $100 for first hour. A 36 month old refrigerator is in essence a disposable item. Basically for a $700 fridge… that breaks down to about $20.00 per month service charge and then it’s time to replace!

We purchased the Maytag front loader Neptune washer and dryer set in 2006. Since then, the washer violently vibrates during the spin cycle - moving out of place and requiring me to move it manually. A certified Maytag technician came out to fix it and could not. The Maytag representative I spoke with said the circuit board is known to be defective and Maytag has not given any direction on how to fix, but that the board is irreparable at that time (in addition to the mold smell that emits from the washer despite the fixes for this). The old washers also used to have a coin receptacle so that any coins that were left in pockets went into the coin receptacle instead of into the pump area. This protected the pump assembly. But to cut costs, they took that coin receptacle out. This causes any coins or other possible things that fall out of the pocket to go into the pump area, getting lodged in there and requiring a costly replacement for the part in addition to costly labor. This washer does not do the best job in the spin cycle because it vibrates so much, leaving a lot of excess water in the clothes. I have also smelled a burning smell when doing loads that suggests there may be electrical issues that could cause a fire hazard. Then there is the dryer. The Maytag Neptune front load dryer has design issue with the electrical assembly. We smelled a burning smell and unplugged it. After taking apart the front cover, the heating coils had set on fire excess lint that had gotten into the heating assembly. In addition, the coil snapped in half, possibly causing a short in the wiring. This also caused other electrical issues that are causing more money to fix. In addition, this is the second time we have dealt with electrical issues with the dryer that have cost us over $400 to fix, including having to replace the drum because it was cracked. Lint and other items seems to get into the very important electrical areas of the dryer due to a faulty design in the lint tray, because the lint goes right through a hole into the areas where the heater coils are, which caused the burning smell in our dryer. In my opinion, both these machines could be very good machines if they were not made so cheaply and if they put good quality into the machines. They dont seem to be worth the price and the support is not there. Even more frustrating, the company does not stand behind the product, leading me to believe that they know about these problems, but dont want to fix them when they go bad. This can pose a hardship for families waiting for two weeks for parts while their dryers or washers are broken. Not to mention the enormous repair costs after the warranty has expired. Try to get them to replace something on the warranty and you have even more problems.

Have a Bravo Quiet Series 300, does not clean clothes because on not enough water to wash with. Have to set it on Bulk to have it clean good enough. The way it agitate and rotate the clothes turns the wash into knotted pretzels (this also makes it harder to clean the clothes) which in turn makes the spin cycle vibrate badly. Cannot put wash in and leave because of this.

Purchased a new Maytag washer from a local Hardware store chain. Waited 3 days for delivery. Old washer was hauled away. Started using new Maytag Centurion the same night it was received. There was a funny odor coming from the washer that was discounted as new equipment smell. Saturday the Maytag Centurion washer was leaking some odd lubricant that had the same odor as the mentioned new equipment smell. Since this lube had been leaking out in close proximity as the liquid detergent my wife used a towel to clean it up. This towel went into the laundry with other clothes.Now Im concerned that whatever this oily stuff is, it’s in all of the clothing that was washed with the towel. Since I live on the West Coast and Maytag only answers the phone during the week Eastern Daylight Time I will call (2 days) after the fact. You might do well by finding out what this lube stuff is before you take it home and how youll have to deal with it once it leaks.

Convenience, small, clean while you doing other jobs, it cleans while you sleeping, it's not loud, not expensive, comes in different sizes and colors, it's another helping hand, you will love it, it's worth the money.

Maytag fridges, obsolete in less than 3 years. TWICE! My last Maytag fridge dies at about 2.5 years. I called up customer service. It was a compressor not repairable. This was an expensive fridge. Reluctantly we bought another one as the space could only accommodate a Maytag. Again less than 3 years old, the ice maker is shot and the plastic inserts are all falling apart. This time Ill renovate my kitchen for that extra 2 inches to accommodate a different brand.

I purchased a front load washer over 2 year ago and the bearing on it has gone bad. Maytag jumped at offering to ship the parts to me at no cost (which at the time I thought was great). I waited 3 months to finally get the part, because it was on back order, and now was just hit with the labor bill! If I would have known a brand new washer was going to go bad after 2 years and cost me over $500 to repair, I would have gone with another brand, In fact, I will never buy a Maytag or Whirlpool. I will ensure that I tell everyone and post comments all over the website about how ** of a product Maytag/Whirlpool produces. Companies like these give the U.S. a bad name! Maytag, you suck!

I purchased a Maytag refrigerator, stove, dishwasher and microwave in 2006. Like another commenter, I also insisted on all Maytag appliances. What a huge disappointment. About four months into owning the microwave, a computer module had to be replaced. The microwave stopped working about six weeks out of warranty. It just stopped working, period. I was told by Maytag that they consider microwave a disposable product and they would not cover the repairs. It was cheaper to buy a new one than repair the old one so I replaced it with another brand. The dishwasher failed after 4.5 years (would not drain) and again it was cheaper to replace it than fix it. The oven range handle broke off (normal use) in August 2011 and that cost me approximately $200 for the part and the service call. The refrigerator has had two service calls for the ice maker to replace the motor. The first was covered by Maytag, the second by me. This occurred when the unit was approximately three years old. In August 2011, I had another $90 repair because the ice maker drain (?) was plugged and had to be cleared fixed. I have never been able to pay what I paid for these appliances. Prior to this, we always purchased a middle-range appliance and we never had problems like this.I will never purchase another Maytag product again. This is so disappointing. I live in MI and I wanted to support a MI business. Unfortunately, I wont be able to help out this particular company any longer. Dont buy Maytag appliances. It is a waste of money.

You get what you pay for, you can go cheaper with no frills and watch how clothes wash, also run afresh through the washer as recommended. Also use the correct amount of detergent. Maytag isnt as good as it once was but it is the top of Whirlpools line of companies.

The refrigerator has been very dependable for over 14 years. The biggest problem we have had is failure of plastic tracks on drawers that break and had to replace drawers and other problems with plastic components like deli drawer coverlet, and door shelf door plastic. Recently we have problems with the touch control panel on front of door. Not working properly for ice dispensing and temp. control although temp is maintaining what we had set prior to failure of control panel.

I purchased this Maytag Dishwasher Model MDB8949SBM on November 23, 2013 and installed dishwasher in late January after new cabinets/countertops were installed. After four months the control board failed. I live out in the country and Maytag does not pay for a repairman to make a special trip for repairs, so we had to wait 2 weeks when the repairman was in the area. We purchased this dishwasher on reviews which seemed pretty good, but never bothered to check on complaints of Maytag dishwashers. I can see most all complaints are the control panels failing. Well it is November 19th and the control panel has failed again. My wife said the lights blink and when she presses a wash cycle, a different wash cycle will light and blink. She will press the start button and nothing happens. You can bet I will call first thing in the morning as the warranty will expire in a few days and I will write the persons name down and the time that I talked being that Maytag seems to lose conversations with customers. I hope Maytag doesnt give me the runaround like may others on this site. I dont understand why Maytag doesnt correct this problem that they have known about for years.

I bought a Maytag refrigerator, model MBF2258XEW, March 2013. Bottom freezer, single door. The past 3 or 4 weeks I have been noticing water occasionally puddling on the floor at the freezer. The ice maker has never been hooked up, with no problem before now. I recently noticed that my wood floor is darkening in a spot that often gets wet. After reading some of these complaints it appears I am not alone experiencing water problems with something that is sold on its reputation for being trouble-free. I also see that I should expect to pay a few hundred dollars out of my pocket to fix the problem. Very disappointing.

My husband and I purchase both Maytag Washer and Dryer 7 month ago 2017, because we have purchase Maytag washer before and were very happy with it. But this new Washer does not clean clothes at all, it is worthless. We will not purchase another Maytag Washer again.

My wife and I bought the Maytag commercial Bravo set about 5 years ago and both the clothes washing and dryer machines are still working as great as the day we bought them. Im a bit biased though as I bought Maytag commercial products in the past and will continue to do so because its they are a dependable company made a reliable machines.

Maytag water efficient, no central spindle top load. Clothes come out with scum on them. Really a problem on the solid darks. I have to scrub with terry cloth to remove. Maytag insists this is normal. Refused to honor warranty. Usually check Consumer Reports for quality and best buy. Energy/water efficiency is important. I like to have some control over the machine so that I can use it the best way for me. Such as soak. This machine cannot be manually controlled at all. Also it doesnt have a lint catcher, doesnt filter the wash or rinse water at all. All the lint and pet hair remains on the clothes or even gets worse.The clothes are not clean. I have no way to control the machine for my use. It may be water efficient but seems to use too little water to clean the clothes. Maytag wants to blame the EPA - This is irresponsible on their part. Its an awful washing machine and they made it. Maytag continued to insist that scum on the clothes was working normally. This scum was added by the machine. I used very little detergent; the clothes were relatively clean - just lightly wore a few days. They come out of the machine with streaks of white scum that I have to scrub off. The clean the machine cycle uses a huge amount of water. This is really DUMB: washing the machine instead of cleaning the clothes! Terrible! And Terrible customer service at Maytag. DO NOT BUY MAYTAG.

We bought a Maytag Dishwasher - Model #MDB4949SHW a year and a half ago at a Home Depot Location. We had previously had a Whirlpool dishwasher for 13 years of heavy use, with no issues or difficulties. At the time we purchased our dishwasher, there were various different brands on sale, including the one we purchased. The sales rep at Home Depot advised us that although we could get a similar dishwasher for the same price, that this particular model had a 10 year warranty. When I heard that, all I heard was 10 worry free years. MY MISTAKE. I could never have imagined that a company such as Whirlpool would advertise a warranty, that in the end is made up of nothing but false advertising.We ran a cycle during the Christmas holidays, and detected a funny smell of burnt rubber but didnt know what to make of it. I googled the issue and some people had had experiences with perhaps a plastic utensil or some other plastic, being burned by the heating element, so I figured that its what might have happened. I ran another cycle the next day, and the smell was much less prominent so I thought the problem had gone away. The next time we ran a cycle, the water didnt drain. We called in a repair person, and was shocked to learn that both the drain pump and main control board needed replacing.We got in touch with Whirlpool and low and behold, the only items they cover are nonsense items such as the racks, drum, tub...etc....in other words, the parts that are actually responsible for the running of the machine, are not covered, neither is LABOUR. Therefore, in my opinion, their warranty is trash and should not be relied upon under any circumstances. We purchased a new dishwasher just a year and a half ago, and are left with a heap of junk in our kitchen. Our options? Either spend $600.00 to $700.00 on repairs, possibly more, or buy a new dishwasher. When I asked if there was anything they could do to at least mitigate my damages, I was told....Sorry for your inconvenience...but do you have any other questions. I dont have any other questions...but I do have have a comment.... Make your products better....and dont print warranties that are utterly rubbish, false, and only serve to mislead the consumer. Needless to say, we will not be buying any more appliances from this company. Their one and only goal is profit for their shareholders with no regard whatsoever for the consumer. If I could give it ZERO stars, I most certainly would. :)

Spent $2,000 on Maytag washer and dryer in September of 2020 thinking we were buying quality and a company that backs their products. Forward to January 2021 and were not able to schedule service through their website. Not able to get anyone to answer their phones. Called what used to be our local Maytag service and they told me Whirlpool took over Maytag warranty service and cancelled all the contracts for local repair shops. So, not only do we have a 4 month old washer I wish we had never bought, we cant even the Maytag to service it under their warranty! Never again...

Great when it works properly and doesnt leak! Quietness, cycles. Everything that had to go in went in, well laid out. Stainless steel, clean, good looking. Anything with the Maytag name doesnt last any more than a couple of years. Gone through a washer and dryer with no help from Maytag. The dishwasher was replaced by Maytag because the main circuit board was on backorder for more than 5 months. Washer was replaced with a Samsung. If I had to replace the dishwasher out of pocket I would go to Korea or Europe to do so. Maytag, what a huge fall in quality and reliability!

I asked a simple question online to see the location of the lint trap on my washer, I had read my manual and could find nothing about the lint trap, and to get a simple answer as to location, they wanted to be paid $30.00, I dont want them to come and show me just a simple answer as to where I could find it. It should be in the owners manual but it isnt

Wow, my dream oven, or now nightmare! I purchased a Maytag dbl oven MGR6775BDS in 2007. The top oven stopped working first after about 3 years and this week, the bottom. I cooked a meal on Monday and Wednesday. Without notice, it would not go past pre-heat. I have called several people and they all act as if this was a truly unique situation. Since I have been out of work, both my regular and extended warranty have expired. I had good faith in a product that carried the name Maytag and the fact that it was on sale for $1,200. I didnt know I had so much company. Yeah, I was told I could purchase a repair warranty for the sale price of $340. Oh yeah, I replaced a 20+ year old oven for the new and stainless dbl oven of my dreams.

I purchased a new Maytag from Home Depot. It was delivered and installed by them on 7/20/12. Today is 9/18/12. It is less than 2 months old and the tub is starting to shred around the upper rim. I called to get it repaired. What a nightmare. First I tried to understand a Filipino woman through a bad connection. She advised me to call a different customer service number, 1-800-688-9900. I talked to Crystal. She called up information on me using my phone number. She asked for the serial number as she had the model number available from the online registration I completed on 7/20/12. I told her I do not have that and asked where it was located. I also told her that I was unable to get it at this time as I am handicapped. She advised me that I had to show my repairman the receipt or I would have to pay a $60 service charge. I get nervous about throwing good money after bad. So I then asked why. If the serial number is so important, why is it not a required info when you register online? She had no answer. I asked to speak to her supervisor. I waited 4 minutes. Enna finally came on the line. She gave conflicting info about my online registration. She said I was not registered online (if not, how did Crystal have all my other info including my model number? Why did Crystal tell me I had registered without the serial number?). Enna told me that the repairman could key in the serial number when he gets to my house and if my washer was under warranty, I would not be charged. Again I asked why, if the serial number is so critical to the process and with all the info they seem to have on me (name, address, phone number, model number, place of purchase, date of delivery, etc.), why is the location of this very critical number is not in the owners manual? Why do they allow you to register without it online and why dont they track sales and delivery by serial number? She was unable to address these issues. I asked to speak to her supervisor. She told me she would give me her supervisors name and number (Kim, **) but she would not give me a last name or contact information. She told me that she was the highest level that I was allowed to speak with.Bottom line, my Maytag is falling apart, getting through the red tape to get it fixed under warranty is silly. Maytag ignores its own concept of tracking by serial number and does not support the use of serial number by telling you where it is located on an appliance or requiring it to register online. Calling customer service is a joke! I was mad when my new $800 washer started to fall apart. Now I am just sad with the way we allow manufacturers to treat us. Mad about the way we allow them to operate in the United States. They create junk or junk parts overseas, products fall apart over here, calls for repair get routed around the world, and then they create more red tape and call it customer service. I made one bad choice. Hopefully, you are reading this and can avoid your own.

My name is Mrs ** and I dont have a complaint. I would to tell you about our washer. It is a Maytag. It use to be my mother-in-laws. She did laundry in it for 4 grown boys and 1 girl plus her and her husband. She passed along to my husband a long time ago. And now it does laundry for 6 kids plus my husband and me. I run it 2 days a week sometimes more. The washer is between 25 and 30 years old. And works good still. Im not sure how much longer it has but we are happy with it. And soon Ill be washing for 7 kids. We have made a decision to start looking for another soon. But I wanted to share my story with you. My husband is now in his 40s if it says how long it has lasted. Thank you.

Have had this set for about three years (was a gift from my parents on having our first child), and its horrible. Clothes come out partially dry, with NEW stains on them, torn or frayed, and twisted into knots. Its supposed to be a high-efficiency washer but we often have to wash things twice to get them clean. We now have two little boys and Im starting to save to buy a different set (no Maytag ever again); disgusted that I cant even sell this set in good conscience. Will either be a donation or an eyesore for the landfill. Worst $1100 ever spent.

Purchase a top loader washer machine in Nov 2014, it is now Jan 2015. It is not completing drain cycle, leaving wet cloth. I am Not happy with the service. I had the tech people come out 3 time and saying to call customer service, and they keep sending out people. They do not want to give me back my money. Unhappy, waste of money, will not get another Maytag appliance again.

My only issue is that I am short and find it difficult to reach the wet clothes to put them in the dryer. Other than that I am quite happy with the machine. I have had no problems to date. Thank you.

Weve had our Maytag dishwasher for less than 4 years when the control panel quit. The repairman came today. He was here 10 minutes and it cost us half as much as a new dishwasher. Its just the two of us and we use the dishwasher once every 4-5 days. Almost laughed when the repairman said the part and labor was under warranty for 90 days! There is no quality control anymore. Just greed.

I bought this Maytag Dryer in May 23, 2015. I had nothing but problems. I had 4 techs come out and say different reasons why it does not work. I had the vent exhaust clean out. Still not working, the one tech said there was not enough clothes for the dryer to sense it wet. I did a huge load, still doesn’t work. The sensor for the vent keeps popping up and it’s cleaned. I have to pull it out and in to get the signal light out. Cant turn on the machine. It still does not work. I tried contacting Lowe’s, since I bought an additional services plan. They said I have to call every thirty days for three months. That means I have to take my time out of work and wait for a tech for three months to get make a complaint and TRY to get new one. I really disappointed with Maytag and Lowe’s. I have a tech coming out this Monday, 11/23/2015 for another services call. I will never buy at Lowe’s or Maytag again. How many times does a certified tech from Maytag have to come out check a brand new dryer?

MTB2656DEB - Well my fridge is now about 12 years old and from the beginning it was horrible ice as always forming under freezer door. The cold cut draw broke 3 times with its cheap junkie plastic. I hated it from the beginning. I have owned a GE double door with ice maker for 26 years. Wish I had kept it.

I have a warranty on my Maytag refrigerator. My icemaker has been broken for six months. I have had repair people show up frequently to try and fix it. Six months and six icemakers later, it still cant be fixed. Remember, I take off work to meet these repair people who sometimes show and sometimes dont. They elevated it to the manufacturer who was going to come out and look at it on Friday, November 23 between 8 and 12. (This is day after Thanksgiving is my only day off.) He doesnt show up nor does he call. So, I called and he is running behind. I should wait until he gets here. Evidently, he doesnt have a phone. These people are totally disrespectful of other peoples time. I didnt mind waiting for it to be fixed but I do mind people who have no consideration or respect for other peoples time.

Have had Maytag HE washer for 4yrs, so far it has broke down three times. I contacted Maytag and they asked if I had bought extended service contract? No I paid $700.00 for this washer and had expected it to work a little longer than 2yrs before seal in door is cracked. Would NEVER buy another HE or Maytag product again!

I bought your Maytag model MDB7749SBW1 dishwasher on May 22, 2013. We bought Maytag because of your reputation...not because of price. However, in September, 2014 (2 months out of warranty!!), the control panel stopped working. I called the 800 number and the best they could do is to extend the warranty for 6 months BUT only after we paid for repair and control board replacement. This is not cheap!!! We were furious. I looked if there were recalls on this model but there is not (should be). Anyway, after we paid for repairs and a new control panel put in ($160.00 +- for part itself), we were very cautious about touching anything on that dishwasher. YOU HAVE an issue with design and I can give you link after link of other customers who have expressed the same thing. So, here we are in 2017... About 2 months ago, we noticed the exact same symptoms with the control board.In fact the ONLY way we could start the dishwasher was to turn off the breaker, let it sit for 20 minutes - overnight and then turn back on and hit the start button. We lost all control over the settings. Only auto clean and delay 2 hours were working. Yesterday, I purchased yet another control board ($179 incl tax and shipping). I plan to install myself. If I could afford another dishwasher, I would do it and never buy Maytag again. Maytag really ought to be ashamed and if they were truly concerned they would offer these defective parts at a steep discount or better yet, recall. I plan on submitting something about this issue with any consumer group I can find. I guess the only way to spread the word and perhaps force a company to respond is to post on social media anymore. This is NOT a like.

Hello, I bought the above top load Maytag washer last summer and shortly after purchase the spin cycle was accompanied by a load grinding noise. This became progressively worse per use and I contacted Maytag Canada. The experience calling is a challenge with often busy, and at times long waits. When I did get through on the line they were very good customer-service-wise and arranged for a local accredited company to attend my home and assess the problem. Service visit number one resulted in the lack of parts to fix, so I waited two weeks for the next visit with appropriate parts. Washer began to grind again, I called Maytag, another appointment was set, service call #2 again resulted in the SAME parts being replaced as service #1, and upon departure the washer immediately resumed grinding. Call #3 to Maytag and a 4th visit was scheduled to my home. This time with a different service provider, parts changed washer not fixed. Maytag called and this time I asked for replacement. Three weeks later I received a new washer. The version was updated so the drain hose no longer reached my drain pipe. Once sorted out, my first wash today with the new unit and GGGRRRIIINNDDDING.. I would not recommend this product. Will be calling Maytag again Monday.

Lets be real and say that people with good experiences dont often end up on websites writing reviews because they are busy enjoying their product! I purchased my set in early 2012 and will admit that initially there was a learning curve with using a washer with no agitator. I enjoy doing laundry and Im really good at it but with this washer I had to change my routine. Always pretreat stains. Deposit clothes loosely around the drum and shake clothes loose before putting them in the dryer. My clothes come out great! I have a child, two dogs and a greasy truck driver man and everyones clothes smell great. I can wash my king bedspread and anything else in my house with no issues. And my washer has never torn any of my clothing, however fragile. I dont iron often and I hand wash nothing.I give 4 stars instead of five for the extra steps to ensure my clothes are clean and wrinkle free. No they dont make things like they used to but thats with all the new stuff. My moms 3000 dollar Samsung set (her washer) isnt working as I write this. Too bad more people with good experiences dont get online and share. Hope this has been helpful.

So wife and I purchased a Maytag dishwasher in late 2012. A year and a month later it turns into Hal 9000 from 2001 Space Odyssey. I press normal, it shows light rinse. I press heated dry, it tries turning off the life support and blowing me out the air lock. Finally, in March it dies. No power, no nothing. $500+ for an appliance that lasts 2 years. So for the past few months, while we wavered over buying a new brand or spending $250+ on a repair, we were washing dishes by hand. It was as bad as my grandma used to say it was. Then, by chance I ran across a web blog talking about this being a common problem, and there are hundreds of complaints, and its a problem with a $4.00 part on the control panel that can be fixed with a Q-tip, rubbing alcohol, and silicone... Im not a handyman by any stretch of the imagination, but even this I could do. Unplug or switch off the breaker. After unscrewing all the screws, (not your standard or Phillips head either) unplug the control panel from the control box and remove the control panel. On the back, youll notice a flat cable (pictured below) that will have dark marks on the opposite side of the part sticker. Gently clean this with a Q-tip and rubbing alcohol. I then covered the back (side without sticker) with silicone, (you can get at hardware store or Target) let dry, and put everything back together again and now its working better than new. Im regarded as a master handyman in my house, and I didnt even have to hear the dishwasher sing Daisy Bell as I disconnected it. With such a simple fix, Im amazed Maytag didnt just own up to it and get it addressed. The millions it will end up costing them in the long run, by this frustrating experience shared by us all will have them thinking twice in the future (hopefully). It is a shame they seem to be adopting the business model of American auto manufacturers of the late 80s. Ill update this in a year and a month to let you know how the fix worked, and you owe me a beer for saving you $150 - $600 for a repair or replacement. One word... VICTORIOUS!!

Dishwasher worked fine for the first 12.5 months, and lo and behold 1 month after the warranty expired, I had my first repair, a new motor. A few months later, I had my second problem, the thermostat. A few months later, I called Maytag because I thought that the control panel was probably shot (based on my previous Maytag for which I replaced the control panel 4 times, before Maytag finally agreed to get me a new dishwasher). At that point they sold me an extended warranty which for 300 they would make this repair, and any other repairs for the next year. They have been out 7, yes 7 times, in 4 months. They would probably be out more often, but since it has been difficult to get a repair person out here, more time than not Im washing dishes by hand. Their customer service is horrible, their products worse. Still waiting for the dishwasher to be repaired. They wont send out a different company, even though they have been out here 7 times, and keep coming back. Even when it is repaired, they will not cover the cost to replace the soap bin, the racks, the wheels on the rack, and all the little pieces made out of the same quality plastic as the stuff I buy at the Dollar Store (except when that stuff breaks, it doesnt ruin my hardwood floors). Dont buy a Maytag, roll up some $100 bills and light a match, because you can look at a pretty flame and wont raise your blood pressure dealing with their customer service.

My stove has been reliable and efficient. I bought it about 11 years ago and it looks nearly new. I have a gas range with 2 ovens. The top looks scratched a bit from just cleaning. The only negative is the top which has some scratches if you look closely and when I first got it, I had to have an oven gasket replace. Still I feel it was a good purchase.

Like many people here, I have a Maytag Dishwasher Model # MDB7749SBW3 Serial # F40107007. We have had this dishwasher for about 12 months to 18 months. The first indication that there was a problem was some of the lights were acting strange. Then the dishwasher starting going nuts. I removed power from the unit thinking that maybe the controller became confused. The problem persisted. I would hit buttons and either nothing would happen or something completely different would happen.I take the dishwasher door apart and remove the touch pad. I notice some discoloration on the ribbon cable. I remove the glued on front panel to look at the electronics behind it (see pictures) and I see some discoloration there as well. So using my multimeter, I find that there is a direct short between pins 4 and 5. I vigorously flex the cable at the point of discoloration and the short goes away. So at this point, I doubt that I can get just the flexible circuit strip so Im going to have to pop for a new touch pad assembly. I didnt go further in the measurements as there was no point since I already detected one failure. Furthermore, I inspected the computer control unit and I did not see any obvious signs of corrosion or discoloration anywhere on the processor board. So it appears that there is no problem with it.Conclusion: Many people are at a disadvantage when it comes to electronic devices. In my professional opinion, this is clearly a failure of the insulating material of the ribbon cable due to environmental contamination. Visual inspection shows that corrosion of the conductors is clearly evident. About Me: I have been an electronics technician on and off for over 20 years now. I have a 2-year college degree in electronics technology and I am currently in school to become an electrical engineer. In my house, when something breaks, I fix it.

I purchased a Maytag 2000 series washing machines. It broke and needed to be repaired within six months of purchase. It continued to break and need to be repaired numerous times and its only a little over 1 1/2 years old. It ripped and ruined clothing on numerous occasions. It would not drain and the door would lock with clothing inside thus ruining them. Both of these issues occurred on more than one occasion. Maytags solution for their defective washer was to keep referring me to my warranty. They were no help at all. My warranty finally came through for me and I was issued a full refund through the warranty I purchased at the time I purchased the washer. My new washer (which is not a Maytag) is being delivered Friday. So finally after being without a washer for over two weeks I will be able to wash clothes again. My experience with Maytag was frustrating and aggravating to say the least and I will definitely never purchase Maytag again. They are far from reliable.

I hoped the Maytag Maxima would compare to my old Maytag Neptune and it didnt even come close. Very disappointed. Doesnt fill with enough water to even WET the towels and doesnt rinse any of the soap out of the clothes. Been using it since 12/2015. Hate the Maxima. I looked for the brand (Maytag Neptune) which I couldnt find. Settled on the Maytag Maxima which is a complete bust. The Maxima doesnt fill with enough water so Ive had to add water to both the wash and rinse cycles. It has also become very noisy. The repairman has already stated that there is nothing he can do about the lack of water since the amount of water is set in the factory and cannot be changed. The Maytag Maxima is a complete bust for me! Its a front-loader that has me adding water (at least 2 gallons) to every load no matter how small. Wish Id bought a GE top-loader that Ive seen advertised.

The washer is so loud it can be heard all over my home (my home is 2700 sq.). It sounds like metal to metal grinding. I was told thats how the run and the first bit of water isnt enough to even wet the clothes. Id never buy another one (even though this is my 3rd Maytag washer. Im 78 yrs.old).

My complaint is not against Home Depot but Maytag Products. They are inferior products. Stay away from Maytag! Note: We are in our mid-to late 60s, no kids using these products and they do not get a lot of wear and tear. Maytag Microwave: MMV 4205DS-0, May 29, 2014 we purchased Maytag appliances for our kitchen (stove and microwave from Home Depot). I liked the 10 year metal warranty plate attached to the front limited warranty of the microwave. This means nothing! They cover the stainless cavity of the microwave (a part that will never go bad). June 3, 2014 this microwave was delivered. Thanksgiving, the microwave went out November 30, 2015 this was replaced with GE Profile Model JVM3160RFSS for $178. November 30, 2015, Diamond Factory Service was here for the Microwave. We paid $90 for the service call. They wanted $228.09 to repair (1-8206419 Switch $15.22; 1 W10269460 Switch $27.03; 1 W10727360 Microswitch $27.03 and Labor $155.00). Maytag Dishwasher MDB7749AWM. Purchased from Al race Appliance for $599.95 total with tag etc was $920.27 on 5/16/12. So thankful was purchased the additional warranty for five years. We have had 2 service calls so far for the same issue, which is W10356494 Console CMFF0312434. This is a known problem (it will not start). I wish I would have googled the model before purchase was made. When the warranty expires, this will go to the curb too.Also, purchased Maytag Neptune Washer and Dryer from Best Maytag, Rockford. The dryer had problems with the circuit board after a short time. Too expensive to replace. Our family and friends ALWAYS purchased Maytag only. No more! Stay away! We are waiting for the oven to go next. Oh and check out the bottom drawer. There use to be room for pots and pans. No more. Lucky to get your pot holders in there.

I bought a new Maytag washer two and half years ago. One of the new HE (High efficiency) models. Clothes do not get washed clean. But not only that, now its not washing at all. My previous machine was a Maytag...Had it for 22+ yrs. I guess Maytag quality is no longer what it used to be. Disappointed customer!

I have had this washer 4 years...I bought this washer in May 2016. It makes 3 very loud noise as it moves into its next mode/cycle. Found out this is normal. IF, it is close to your living room, IT is loud.. I called again, saw that it was not filling up. 1/5/2017.. IT will NOT fill up to wash my clothes properly, clothes were still dry!!! Came out, (they sent a company near my area), said everything is right. I have tried, by sending messages, many times to get them to check. No one seems to care. The machine allows water to go out the bottom, rather than fill in the machine. I watched it myself. THERE should be a recall on this machine, definitely, something is sooo wrong.. I NOW have to put it on BULKY SHEETS full time, to get my wash clean.. NO energy savings there... BUT my clothes are finally clean!! Seriously, something is wrong...

I have a Maytag refrigerator that is about 6 years old. I like the fridge, but the icemaker no longer works and water constantly drips from the door. They will not fix it, even though we have an extended warranty that they have provided. I have waited for months and I am told an icemaker is not important and the fridge is still working, so why am I complaining? When you pay for a fridge with an icemaker and water dispenser, I believe it is part of the refrigerator I paid for and it should be fixed, but Maytag doesnt seem to think so.

Bravos washer purchased Sept. 2016. I purchased the Maytag washer based on experience and reputation. I am so disappointed in this washer. I have had the control board replaced after only 3 months and it vibrates, shakes and is very noisy. It does not fill with enough water and the clothes are tangled at the end of the wash. I will never buy another Maytag.

We purchased a dishwasher (Maytag) two or three years ago. We have had nothing but trouble with it. The welds on the upper rack broke. The wheels on the low rack keep falling off. Water leak happened recently. The start button broke. My wife and I decided to just get a new one rather than keep sinking maintenance costs which are going to keep adding up.

Maytag MVWB835DW was less than 2 years old (purchased 1-14-16) when it began to fail. Maytag sent repairman out, he declared it beyond repair. Machine locks, washes and adds more and more minutes and cant turn it off without unplugging 5-10+ times... sometime takes a week to get clothes out of machine because of locking itself. I have extended warranty and yet when I try to contact Maytag, to have them honor this, there is eternal wait on phone, online, no help whatsoever. I read via Consumer Affairs that there are almost 3,000 reviews on this specific machine being a problem yet amazingly the Maytag man never responds! I have spent many many hours with no resolution. Amazon says so many reviews have been written about this, that they are unable to take my review because of excessive reviewing.

I have a Maytag refrigerator that is 7 years old. It works fine except it needs a new freezer door gasket. In trying to get the part so it can be repaired I discovered that they had chosen to discontinue production of this part. I can no longer get it anywhere. They were the most unhelpful customer service I have ever worked with. They refused to try to find a part for another model that may work. They refused to offer a discount on a replacement product. They even refused to give me a phone number to talk to management. I had always been a loyal customer to their brand prior to this but I will never again purchase a Whirlpool or Maytag product. I dont expect not to have an issue but I do expect the ability to be supported in obtaining a commonly replaced part for a major appliance that is less than 10 years old.

We purchased a French door Maytag refrigerator model MFD2561HEB in November 2007. In August 2008, the unit stopped working suddenly. The high voltage control board was replaced under warranty, but the tech could not determine why the board failed. I called Maytag to demand a new refrigerator. The best they would do was to extend the warranty for 6 months, no charge. The unit quit twice more in September. A tech was summoned (paid service call), nothing found. It started working again. Since then, the thing has quit several times. We unplug, move all food to a second refrigerator, wait a day, plug it in, and move the food back. The useless box quit completely this week, not quite 5 years of service life. The tech said the board must be replaced again, no guarantee. We declined. I called Maytag again to demand a new replacement and escalated the complaint. They are to call back, ha! In the 5 years of poor service (and poor customer service) from Maytag, the 30-year old second refrigerator has been up to the task of preserving our food. This experience has made me vow never to do business with a Whirlpool-affiliated brand again.

Control panel start button failed 55 weeks after purchase and installation. Model no. MDB4709PAW. Repair costs for labor and part totaled $298. I have since found out that Maytag dishwashers with this type of control panel are faulty and fail often within first 3 years. Purchased at Johnnies Appliance, Glendora on 6/14/14 NJ; ticket no. **.

First the dishwasher - Control board no longer works. Seen many people with same problem. Dishwasher sitting there useless since cant afford to replace. Will cost as much as the purchase. Stove has defect between glass on oven door. Aqua clean feature is a farce and I feel vent at bottom of oven is asking for a disaster if any grease should spill in there. Maytag will not honor or admit any defects.

Our refrigerator is 2 years old and still under warranty. The ice maker had to be replaced. Now the water leaks on the floor. The deli drawer cover broke and when you get ice out of the ice dispenser it flies all over and goes on the floor. Our dealer has been fairly helpful.

I bought my first centennial washer less than four years ago, warrantied that machine out. It was replaced by best buy because of the warranty that I purchased. We are a family of four, with that in mind the replacement machine was a model year newer and it last just over a year and quit. I bought the machine anticipating that it will last me the next 10 years. With two children at home now that is not working, all I have to do on replace a new machine. The repair shop has told me that they get more of the Maytag centennial machines and then any other washing machine is going to cost me more to repair it than to buy a new machine because I had faith in the Maytag products for many many years. This particular machines are extremely hard to diagnose as to what causes the problem or what the problem is and could take a long time to get it fixed as well as the expense of getting it fixed. I would not recommend another Maytag product nor will Maytag ever get any more money from us. This particular product has become a piece of junk that I cant even get rid of to recycling. Maytag has become a joke and this machine has become a 500 dollar hunk of junk in my opinion.

I have had a few dishwashers in the past, however this is the worst product I have ever purchased. After a couple of years in service I needed a new control panel which cost $200.00. The dishwasher defaults to heated dry and the exhaust for the dishwasher is right behind the copper electrical runs so it corrodes and fries the runs. The way I see it Whirlpool and Maytag saw a unique way to gouge its customers for parts. They also have a rope and plastic cable system that attaches to the door spring that continues to break cost $28.00 a piece, I have replaced two. Now I see that one of the pulley guides (plastic) is broken and split cost??? Here is another brilliant engineering feat, the door panel clips into the control panel so that when the door is pulled in a normal fashion it comes loose. If you buy this line of dishwasher (p.o.s) plan to work on it and buy parts on a constant basis. Here is my advice: buy one control panel, two cable systems, and a couple of cable pulleys or buy a cheap dishwasher as a replacement and save some money. Run from Maytag or its parent company Whirlpool - let the buyer beware.

MBL2258XES1 - Like most of the other reviewers, we have a Maytag refrigerator just 3 years old with a lower freezer that leaks water onto the floor -- and has been doing it for the last two years. We have to take the freezer apart (NOT easy), defrost it, take the back panel off, and clear the drain tube. Obviously a defective design! Cant believe Maytag hasnt done something about this!

Purchased a new Maytag dishwasher just under 1 year ago. After a 5 months it started not working. We called the dealer - who gave us a number to call because it was under warranty. We called the number and it took days to get someone to look at it and not fix it. It needed a new part. Its been over a week now and we havent heard anything, and still no working dishwasher. Our last two dishwashers lasted over 18 years. Kenmore and Whirlpool, never had any issues. This is our first Maytag. Service has been snail pace slow. Dont buy a Maytag dishwasher unless you want to spend your life washing dishes.

Purchased a Maytag smooth-top range about a year and a half ago. Ive only cooked frozen pizzas in it. Have only had it on six or seven times. Havent used the top burners at all. Its an electric range, and I just had it hooked up a couple of months ago, as I was trying to find a place for it in the tiny kitchen. The folks who lived here before me, had a huge refrigerator and gas stove right next to each other, and I didnt want to go that route. Anyway, I went to put yet another frozen pizza in the oven, and the light doesnt work!So, after only six or seven uses, the oven light is busted! My mom had an old Westinghouse Terrace Top range, and it lasted well over 20 years with no problems. The only reason she sold it was because she remodeled her kitchen. It still worked great after all those years. Its after-hours now, but when I call Maytag tomorrow, Im expecting to get the run-around, if the other reviews are accurate, and Im SURE they are. Wont ever buy another Maytag product again.

My husband bought me a brand new Bravo Maytag washer and dryer from Home Depot in November 2010. In May of 2011, we moved and the dryer hookup was electric instead of gas. My husband knew how much I love the dryer, so he surprised me with another Bravo dryer to match the washer. We put the other dryer in storage and were happy with our purchase until April. In April 2012, the dryer stopped working. It wouldnt dry the clothes at all, and every time we tried to dry, the dryer was filled with wet lint. We were only a week away from moving again, so we waited until we got to the new house. The new house had gas hookups. So, we put the dryer that didnt work in storage and were thankful we didnt get rid of the other dryer. Now, just a few months later, the gas dryer isnt drying and is having the same issues as the electric dryer. How very disappointing! Both dryers are broken now, and it has only been 2 years. Each dryer has gotten about a year of use and then both quit. My husband, I and my two-year-old dont do that much laundry to break 2 dryers. My old GE washer and dryer lasted for years and is still working. We gave them to my husbands aunt who uses them and loves them. I agree someone should start a class action against Maytag. These issues are ridiculous!

Like many of the other complaints, control panel lights up but dishwasher will not start. It has had minimal use and is less than two years old. For a product purchased for around $800, it should have lasted far longer. Repairs will cost close to the cost of replacing entire unit. Do not buy Maytag. Their reputation is ruined in my eyes.

To begin with, the Bravos 300 washer was bought because we owned a Maytag previously and it was with us for 25 years. It was still running when we gave it away and the only problem was a small oil leak starting at the drive. The new washer has no agitator, just the new style flat thing at the bottom of the tub. You cannot wash a set of fitted sheets without it turning into a tangled mess. The washer quit working after about 5 years and all indications pointed to the control. The control would reset after unplugging, but would freeze immediately when you tried to enter a command. We live in an isolated place and it is not feasible to fly in a service person. I ordered a new control, but there was no change in function. After several hours of detective work, it turns out that the mickey mouse plug for the electrical connection at the pump had broken inside. Because the pump would not work, the whole control would freeze. We will never buy another Maytag.

Purchased a Maytag MBF2256HEW bottom freezer in 2005. About fours ago, I had to replace the control board to the tune of $140.00. Today the fridge quit working and this time it appears to be the compressor, so tomorrow we will be shopping for a new unit. It will not be a Maytag.

This washer is no better than a glorified garbage can. Maytag AKA Whirlpool should be ashamed to put their name on this product. Like others before me on this website my washing machine sounds like a jet is taking off in my basement. When I contacted a serviceman, he told me the drum seal is broken and the bearings are shot. I have the machine since April 11, 2011. Not even three years to date! I do not have an extended warranty so shame on me to believe that a 900.00 machine should last well beyond 3 years. Unfortunately, I am getting the run around from Whirlpool as all of you have experienced. This is criminal. Not only are we as consumers being defrauded by irresponsible manufacturing but these huge hunks of metal and plastic are polluting our environment. Our parents had washing machines and dryers for as long as 20 to 25 years and they actually cleaned clothes. We now have high efficiency machines that destroy our clothing and leave them dirty and wrinkled. They are now made to break in 5 years and from what I see on this website the average for breakdown is becoming 3 years. Do you think that this is not by design? The service call turns out to be more than the value of the machine, so the repairman doesnt even profit as consumers refrain from costly repair and repurchase. The only profitability is gained by the manufacturers that keep pushing out junk to the consumer. These manufacturers should be accountable like the American auto-manufacturers became accountable for the junk they manufactured at the expense of a whole city, Detroit.

Maytag Bravo XL - We bought the set about a year ago, after high recommendations from the salesman at Best Buy. This washer does not clean clothes - they come out with soap & spots & white stuff, even after I use the deep water or the extra rinse cycles. These cycles take well over an hour. When they are finally finished, my clothes are twisted into ropes that have to be unwound & taken apart before putting in the dryer. I hate to think what its doing to more delicate clothing, getting stretched & tied up like that. This washer is awful - cant wait to get a new one. The dryer isnt much better - cant believe a $900 dryer doesnt have a steam refresh cycle! And the controls are so touchy - if you actually push them, they dont work. If you lightly hover over the button & barely breathe on it, it does - very strange.

Bought top of the line Maytag Commercial Technology washer because it was supposed to be the most advanced on the market. My experience has taught me that advanced does not equate to efficient, effective, and expedient. The washer settings for an average load (sheets or towels or clothing) is about 111 minutes per load (nearly 2 hours!!). To adjust to what would be a quick wash is about 25-30 minutes BUT the washing part of that is only about 5-7 minutes. I feel like a Pioneer Woman because I must spend most of a day to run four (4) loads of laundry (sheets, towels, dark clothing, white clothing). This is extremely frustrating!! I am sorry I purchased this product.

We purchased our Neptune washer and dryer combo MLG2000AWW from Circuit City in 1999 for $1900 also purchased the extended warranty. Here we are 15 years later and time to replace with new Samsung units. Besides having the main bearing replaced after 6 years in service, and having a sensor and a switch replaced on two separate occasions all covered by the warranty, our Neptune provided exceptional service throughout the 15 years. My understanding was that Maytag was bought out and run very poorly in the early 2000s as our unit was produced prior to that time... when Maytag was Maytag.

MMV5207BAQ purchased in Feb 2009. I paid $512.00. 5-09 Bob Millers Appliance replaced the door because it bubbled. 10-11 Bob Miller appliance replace the door because the handle broke off. 3-12 Bob Miller appliance replace the door because the handle broke off. 10-16 Door handle broke off again under normal wear and tear. 12/14/16 I went to Bob Millers Appliances and was told to contact Whirlpool. 12/16/16 I called Whirlpool, Tina said, yes it is excessive but it is not under warranty and they do not make the microwave any longer and they cant do anything to repair it and they can not fix the issue. I find it how to believe Im the only person who has had this issue. I dont have kids. Its only me that uses it.

I have a Maytag Bravos washer bought 6 years ago. Recently, it started giving trouble by stopping at spin stage. I contacted a local service company and they immediately told me even without looking at machine, that it is a control board problem and will cost a lot to repair and suggested to buy some other company washer instead of repairing. They told it is the third similar complaint this week. But I contacted Maytag and they suggested their factory authorized technician who could not correctly locate the problem but charged for the visit. Later he also came to the same conclusion. Thus my previous washer from another company lasted for more than 20 years (Still in working condition), this washer required a service with a cost same as its price!!!

I purchased my first Maytag (Bravo Washer) appliance in 2013 and thought this washer would last me for a minimum of 10 years. It started making noises occasionally right away but I wasnt too concerned until it started sounding like someone was banging on it with a sledge hammer. I waited 8 days for a repairman who told me the bearings were going out and it would cost $400-500 to repair. This is the worst washing machine ever manufactured. My advice is to buy any other brand. Dont be fooled by the Maytag hype. Their quality is nonexistent. I am shopping for a new washer.

I purchased high end Maytag washer, dryer, dishwasher and microwave in May 2010. On Saturday 4/25/14, the Maytag Microwave stopped heating. The fan runs, the panel, display, lights, clock, and tray all work. It just doesnt cook. The Microwave was installed in June of 2010. Not even 4 years old. I have tried to troubleshoot via the instructions that came with the microwave, i.e. Check the demo mode is not on. Dont know why after 3 yrs it would be, but checked it. No help. Pulled the plug out and replaced; turned breaker on and off; checked to see if its was locked. Nothing. I then checked the door and I found that the plastic inside panel on the latching side of the door is pulling away from the door itself, which is part of the locking system. The magnetron shouldnt work if the door system isnt closing properly. The latch system is what is causing the door to pull apart. I am wondering now how much microwave exposure my family has been getting from a malfunctioning door? I have had a Microwave, dishwasher and refrigerator made by Maytag in the past. The refrigerator is 14 yrs old and still works fine. The microwave and dishwasher were at least 10 yrs old when I replaced them with the new Maytags I have now. Here is the problem. Maytag is not Maytag Corp. anymore. Whirlpool Corp now owns the Maytag brand. Prior to the old Maytags I had, I had GE fridge which was junk, and Whirlpool, dishwasher, stove and microwave. They were also junk. I swore I would never buy Whirlpool products again. Surprise.

I think that I finally figured out a way around the piece of junk Maytag sold me. I bought a Maytag french door, stainless, yada, yada refrigerator in 2006. When it broke down, see later description, the first several times it was ok because of the warranty. This POS has failed 7 times requiring $300+ to fix every time. When contacted about the issue, the people at Maytag seem happy. The business model is working perfectly. There goes another sucker. The refrigerator begins its eventual breakdown with the door alarm light and sound beeping constantly. Beeping that continues for days and weeks. The next progression to failure continues with it not beeping anymore but now the interior lights do not light when the refrigerator is opened. Finally, the refrigerator stops cooling entirely and it is dead.Now, Maytag no longer wants anything to do with it so you need to call a repair man. When the repair man arrives, the entire time he talks about what a piece of junk Maytag is. They, every time, at first think it is the switches and replace them. This NEVER fixes the issue. Next, they have to replace the computer brain. $400 to fix. EVERY TIME. Now, at least every year. If you buy Maytag and have a similar experience, get your wallet out. Sell you junk then dont stand behind it.

MF12665XEM7 - Maytag Refrigerator purchased from Home Depot. We initially thought it to be a good value until it started leaking puddles of water onto the floor to the front sides of the bottom freezer drawer. This event repeated itself and I feared the water would seep between the floor tiles and begin to degrade the sub flooring or possibly cause mold as well. Upon further investigation of lying on my side and pulling the bottom drawer open, I felt, what I thought to be ice on the bottom of the refrigerators floor. I gently inserted a smooth butter knife and with a nudge, a whole sheet of ice about one half inch thick, lifted from the refrigerator floor. I have since had to repeat this about every three weeks or so. Im nearing retirement and shouldnt have to lay on my floor like this to protect my floor and to keep my wife and I from a potential hazard of a slip and fall from this water on the floor! Dependability People? Hardly! I think they got outsourced! Im disgusted! Thank you!

Purchased less than a year ago, Machine stopped working. Approved service company says no error codes visible must be ok. Machine still does not work month later, service again does not show up for call, following month same. Its still in warranty but they claim it is fine. Error code disappear right after popping-up no storage of error codes.. I had to buy small washer to manage home. Really bad choice of product. Will not use this brand again.

Purchased a new Maytag dishwasher three years ago. After having it for one year the panel box no longer worked. Had to pay $300.00 to repair. Now half way through washing the dishes again no water will go into the machine. Only the first part of the cycle. I am sure it is going to be the panel box after reading other peoples problems with this machine. I will not pay to have it fixed this time. I will have to buy a new dishwasher. I will never purchase a Maytag product ever again. I have lived in my home for 40 years and never had a problem with any appliances. This would have been my third dishwasher in 40 years and as you can see it has not even lasted 4 years. I will inform my friends to stay away from Maytag.

I purchased a Maytag dishwasher (Model MDB7809AWWI) in Sept. of 2009. In 2010 and 2011, it had dead control panels. The first time, it was under warranty. The second time, it was not, and I purchased a costly service plan to have it repaired. Now, 2012, its dead a third time. Maytag tried to tell me that I could purchase another plan for $289. I informed them that for that cost, I can replace it with a dishwasher that doesnt require costly service plans and yearly repairs. They informed me that their parts only have a 30-day warranty. If theyre not willing to stand behind their products enough to admit that one is faulty, then Im not willing to stand behind them as a company.

Maytag Front load washer mah8700aww - This washer has been the biggest boat anchor of a machine. Nothing but trouble and bad parts. New motor after 18 months, water level sensor at 2 years, main control board twice now at 2 years and 4 years, and now it is showing signs of needing yet another main board. E3 trouble code plagues our home and basement. This machine has been leveled and re-leveled numerous times and still shakes like crazy... I mix my paint cans by setting them on the top... the best use for this machine. Yes it sits on a concrete floor. So not satisfied and will not ever buy another Maytag anything. There should be a negative star rating. It does not deserve even 1 star after being taken advantage of like we and thousands of others have been.

We purchased our Maytag fridge on May 13, 2013. On June 19, 2013, it stopped working. We called Home Depot where we bought the fridge and they told us that we would have to deal with Maytag. What a nightmare. The repair guy came out and ordered a compressor for the fridge. 2 days later, when the compressor came in, the repair guy told us that the fridge was unrepairable. Great, what was I supposed to do with this hunk of metal now? I called Home Depot back, and they ordered me a new fridge, added a five-year warranty for free, and the Store Manager even dropped off a small dorm size fridge for us till our new one came in. Yeah for Home Depot!!!! I would recommend no one ever buy a Maytag product again - what a piece of junk. Their customer service didnt even care; they had the same old story - We will get back with you in 72 hours. Maytag was good when it was built in the US; now its just more China Junk.

Ive had this washer and dryer set for only a couple of years and nothing but problems. The latest is that it sounds like its going into orbit on spin cycle. I cant believe the poor quality of these appliances. Ill never buy Maytag again.

We purchased a Maytag washing machine top load (#MVWX550XW) on 12-20-2010. The switch on the machine that starts it running when you close the cover went out under warranty. They put a new switch in and it only lasted a while. I had to pay this time, $240.00 for repair. Now again, 1-2-2013, the switch is not working. I think that it is a lemon. I called the company and they will not cover the cost. Instead they want to sell a warranty for over $300.00 for one year and then if I purchased it, then they would fix it.If I did that, I would have more money into the repairs then what the machine cost ($583.44). Isnt there a lemon law? It looks like I will have to get rid of this machine and buy a different brand. Yes, Maytag has let me down. I cannot recommend their products because of the quality and answers that they give. I cannot afford an attorney, which leaves me upset when somebody wont cover the cost of the third repair.

Does not wash. Only very small loads get washed even though it claims to wash bedding. Some clothes NEVER get wet. Many times the clothes have to be rearranged and re-washed AND extra rinse. Cycles are over an hour each (then multiply x2!!). Maytag service has been called MULTIPLE times. They replaced the touch pad then the computer board. Both times saying the machine works “according to design/specs”. This is a Very poor design. Maytag should recall this inferior machine as it does not perform the job it is being sold for.

I bought a Maytag washer January 2016. We recently had a issue with it so I logged onto the Maytag website and found a service provider to come see what was wrong. I had to pay a $100 fee for them to come out and look at it. I was told that the transition went bad. The parts were under warranty however I would have to pay for labor, which would be $325. Called Maytag and was told because I did not purchase an extended warranty there was nothing they could do about the labor. I can buy a new washer for $500 why would I spend $325 to fix? Already lost a $100 for them to come out to tell me what was wrong. Completely not right. A washer should last more then 4 years! Do not buy any Maytag produces. Will not last!

I purchased the Neptune HE pair because they are front loading and can be set on pedestals to raise them to a comfortable working height, plus the brand and reputation are both excellent. I like that the chimes can be adjusted from low to high, or turned off. The front loading washers clean so much better and with a lot less damage to items than washers with center agitators. Looks are secondary, thats for sure. Functions like warm/warm cycles and being able to adjust to whatever load needs to be washed is really most important to me. Any appliances with a good, proven track record of reliability with few repairs is high on my list. Expensive appliances should be made to last and be of durable quality! No cheap plastic or weak-looking welds or components, thank you! Quiet operation and dependable cleaning and drying are top in my book, and this pair has exceeded even my picky expectations in total overall performance. They are 11 years old now and look & function like new! I had one minor repair on the washer at 5 years, and not a single problem since. With front loading washers, its important to keep the door open a little when not in use so that they dont get a musky smell. Ive gotten into the habit of using laundry boosters to help clothes, sheets, and towels smelling fresh longer, and putting a small amount in the washer drum has kept my whole laundry room smelling nice. Purchasing the pedestal drawers to set the washer and dryer on added extra storage to my laundry and its much easier for me to load/unload them at this comfortable height. Im totally spoiled by it now, so when I use someone elses laundry room (when I visit) I am reminded how nice my own setup is.

My Neptune washing machine does not drain or spin. It keeps going unbalanced. I am told that I used the wrong detergent. The machine takes a whole day to wash a small load of clothes and then never finishes. Clothes and towels are constantly being ripped and torn. This Maytag product is inferior and we have paid a lot of money for this product that does not work. Repairs to this product are not advised, we have been told that we just need to buy a new one again. This is poor service and poor advice.

I bought the top of the line Maytag washer. I was told they have improved their washer so that it no longer requires an agitator. I was also told the new machine saves you money by using less water. It has a sensor so that it only puts the water needed to clean your clothes. Instead of filling up with water and having the agitator to stir the clothes around, this new and improved machine puts a small amount of water in the machine and vibrates. The end result? All of the dirt and debris gathers in small pockets and sticks to your clothes. In order to save water the sensor only allows a small amount of water to enter the machine to rinse your clothes. When you consider how many times you have to go back and rinse your clothes before you get the caked on dirt off of your clothes, its costing you more money, more time and more aggravation. Oh yea, the maintenance man was out three times before the machine was a year old. The last visit was to replace that fine Maytag motor that was less than a year old. I have pictures that show my clothes with caked on dirt and debris on them after they have completed their wash cycle. It is HORRIBLE!!!

I purchased by Maytag Bravo from Lowes exactly 1 year ago when the gearbox failed. There was a loud grinding sound as the washer tried to shift from wash to spin. Reading through some on-line reviews and complaints it turns out that this is not a new problem and has been known to Maytag for some time. I specifically bought a Maytag because of their prior reputation for quality. Unfortunately, my information was out of date. It is so sad that a company would compromise such an outstanding reputation.

I started hearing the Maytag Microwave MMV4203DW00 beeping this morning after breakfast. I had not used it since the night before to heat up soup in a Corning Ware bowl. Its doing that 5E thing and nothing on the control panel works. Ive unplugged it, waited, plugged it back in and the same thing. It starts off saying Select Clock and 5E and then stops on the 5E. I bought this in Aug. 2010 and it is vented out the wall. Of course, that doesnt work now. The metal rack has never been put in it. Im single and the only one who uses it and I dont use it very much either. And this model only got the one 40-watt regular bulb over the range - lousy. And it doesnt work now either. And the control panel lights up orange. Had I known that, I would have never bought it in the first place. Of course, the stupid orange 5E lights up. Im unplugging it for good. Its not worth fixing. Do not buy this microwave!