The washing machine is rusting and Maytag refuses to take care of their inferior product and obvious inferior materials used, and also inferior workmanship.

I purchased a Maytag gas range about five years ago. After about two months, I noticed that the paint on the burner grates was flaking off. I called the company and they told me it was cosmetic. I have since bought two sets of replacement grates. I call the newest ones my dress grates, which I put on the stove when I am having company. I use the damaged ones for everyday cooking. Last year, the panel flashed. It locks constantly. And often, the door would not open, unless we pulled the stove away from the wall, unplugged it, and that cleared the computer. So, after months of unsuccessful door openings, the handle finally fell off completely. And the door locks whenever the oven is turned on. You have to finish your cooking, press cancel, and wait until the oven cools off, and then it will unlock. I have tried pushing aluminum foil into the latch hole on the door but have not been successful. Sometimes I just put a spoon in the door to keep it ajar while cooking. This cant be energy efficient. Of course, it is out of warranty. I saw a similar complaint about the burner grates. Also, the paint has chipped in several places on the cook top and the disks are all chipped. I am never ever going to buy a Maytag product. Oh, by the way, I called a repairman. I paid $65 for him to tell me that to replace the lock mechanism and the door handle, it would be $400. I can buy a new stove for that, but not a Maytag.

I have now owned my highly efficient and low-cost to operate washing machine for 6 years. It is a top loader and uses HC detergents.This means the washer needs minimal soap to clean the clothes. I especially appreciate the different types of loads such as deep cleaning or regular cleaning. The washer has sensors that evaluate the size of the load and thus only utilize the amount of water necessary. I really like the quietness and being able to get the very best wash because the washer does exactly what it needs to do. It has more than been the appliance that I had hoped for. Love it! It maintains itself.

We bought a Maytag Bravo washer and after less than 6 months of use, it stopped working with an F51 or 53 error (cant remember which because its been a month now). After looking online, it seems that almost everyone who buys this gets this error and has to have a part replaced! And Whirlpool hasnt recalled the faulty part even though everything Ive read says it should be a recall.Its now taken over a month to get a repair person in to fix it. From the time we called Maytag, to the referral to the service person, to the service appointment, to waiting over 2 weeks for the part to come in, its been over a month with no washer. This is unacceptable Maytag! The repair company is finally showing up tomorrow only after 3 left messages from us.Either build a better washer or stock your replacement parts with the local repair companies and you should be reimbursing your customers whove spent a lot of money at the laundromat after spending between $700 and $900 on your washing machines.

In 2011, I purchased 2 Maytag dishwashers, one for my tenant and one for myself. In 2014, the circuit board on my tenants dishwasher failed, when the unit was only 3 years old and of course out of warranty. I first contacted a local repair person, and he informed me that the repair plus service would be close to $300. When I contacted the company, after about an hour on the phone, they agreed to send their authorized repair service person and after his evaluation, would repair the unit with no charge to me, as a courtesy. This whole process took about 2-3 weeks. I felt that was fair. It is now 2015, and my unit, which I purchased at the same time and the same type, now is not working due to a faulty circuit board. My tenant uses her dishwasher more frequently, and that is most likely why her circuit board went first. This is a design flaw, or perhaps planned obsolescence. At any rate, Im not happy with this, and my model is mdb7809awb2, and serial # is FO4205659. Do you know if there have been any other complaints on this? Thank you for your help.Updated on 07/30/2015: After I wrote my review, I contacted Maytag about the problem. After considerable wait times, I spoke to someone who set up a diagnostic repair call, giving me the impression that Maytag would cover it. When the repair company called, they told me that I would be charged $104.95 just for diagnostics. Labor and parts would be additional. I called Maytag again, and they agreed to let the repair company charge back the diagnostic fee. After diagnosing the problem, it was determined the problem was the control panel and not the circuit board. The cost to repair with tax came to $315.85 and it was only this low because the repair company waived the return service trip. I can get a new dishwasher for a little over $400.00. I am very disappointed in Maytag, because I remember the commercials where the Maytag repair man was bored because the products were so dependable they never broke. My unit is only 4 years old, and its sad that it costs so much to repair it.

I have a Maytag Centennial washing machine which is about 3 years old. In the past 6 months I have to replace the actuator twice. I have had Maytag washers for about 40 years. I will never purchase another one unless it is the old style. That would mean that it would be a used one. This machine is a bad purchase. Maytag use to stand for quality, but not anymore.

Bought a Maytag washer MVWC415EW in 4/2015. We dont use the washer heavily but over that time span the paint on the top cover and the side where the cover comes down has bubbled up. It looks like a bad rash but only on a washer. I think the company used inferior paint which can bubble up with the heat of the hot water during the wash cycle. I called the company but they do not cover cosmetic items on the warranty. I think since this was a flaw in the paint used they should at least replace the cover portion which would be an easy fix. Maytags are not what they use be! Last Maytag lasted 17 years with no paint problems or mechanical problems.

I purchased the top load Maytag Commercial Residential washer with an agitator last month. I wanted a basic washer with Hot/Warm/Cold settings, Delicate/Normal/Heavy Duty cycles, Small/Medium/Large loads. I paid over $800 for this washer and I cannot wash my whites or rags in hot water! The hot water setting dispenses hot water, then cold water, back and forth. The end result is cool water. Ive called Maytag, Ive been told that there is nothing that can be done about it, thats how theyre made to be considered HE. I asked them why they even put a hot or warm water setting on the washer.You have no control over the water level, all cycles except for normal run in a deep water setting (full drum of water), I dont know why delicates are in a deep water setting. I only wash a couple pieces of delicates together. I end up using a lot more water and detergent with this washer. I hope we dont have to conserve water in the next few years! So though this washer uses less hot water energy, it wastes a lot of water, my water bill goes up and my detergent is used up much quicker! I cannot add time to my wash cycle, (the actual washing/agitation cycle is very short - 10 minutes) it has to drain all of the water and re-start the cycle with more water! $800 is a lot of money for a washer that doesnt wash like my old cheap washer. The local store cant do anything about it and Maytag brushed me off.

After 15 months of use the Maytag Dishwasher MDB8959SBS2 the control panel start malfunction. I read very carefully about the Home Depot Customer reports before purchasing this built in stainless steel dishwasher, and supposed to be one of the top notch on the market, around $850 retail price. It becomes a big disappointment. After three months of use, the top rack handle broken but it still under manufacture warranty, so we get it fixed by Maytag contractor. Then 15 months after regular use for a family of five, the control panel start malfunction, few bottoms will not start anymore. We are out of luck with one year manufacture warranty and working towards our VISA card extended warranty to try to get it fixed.

This washer had good reviews when we bought it, but now today the agitator is not working. I see there are now 100s of bad reviews of this machine most around the same 1 1/2 year mark. How unacceptable to have a large appliance like this break after such a short time. Ive called Maytag to see if there was a recall and there is not. They offered the extended warranty to me for $325 that would cover all parts and labor. Ridiculous.

Maytag and Home Depot do not back their products or assist customers. While repair my fathers home in Grand Junction Colorado, Home Depot workman grabbed the 30 year old washer and dryer by the controls and promptly destroyed the machines. No - Home Depot didnt do anything despite complaints. I bought a brand new Maytag Washer and Dryer for the Grand Junction, Colorado home. The famous Maytags that are called dependable only lasted 3 months. When I went to complain at the Grand Junction Home Depot - the manager - Cheryl - called me a lair when I said I left phone messages for her. Cheryl seems to represent the best of Home Depot when she doesnt assist customers - is nasty and calls them liars when they say they left phone messages for her. No - Home Depot would not back their selling Maytag, and worse, they wont assist you in finding how to contact Maytag. Cheryls response was - Contact Maytag. Good bye. I was not given a contact or phone number - nothing. I spent over $32,000 at Home Depot fixing up my fathers home and rentals and this is how Home Depot treats customers. Worse I have a worthless Maytag that ceased working after just 3 months. Yes - you may contact me, yes - you may use my name and yes - I will blog on the internet the nastiness of Home Depot in Grand Junction, and the poor quality and poor customer service with Maytag.

I spent extra money on a commercial grade Maytag dryer $1300 before taxes because it had a 10 year warranty. The motor and drum quit - and Maytag refuses to honour the warranty. I am appalled by their dishonesty and lack of integrity. I do not recommend them to anyone.

Washing Machine MVWC6ESWW - The fourth time was October 12; I called. Shreka at Maytag said she would send someone out at no cost on October 15, between 12-5 pm. Justin called from AE at 5:05 pm stating he was on his way. He then asked for my receipts. We were moving and had packed many things. He said he would call and find out. He said they were out 7/2011, 9/2011 and again 9/2011 all for the same problem. I requested in September 2011 that this was a lemon and send me another. I was assured if the same problem occurs, it would be covered. Well Justin said it isnt covered anymore and it was due to being made overseas. The cost to fix it is around $350 to $400. The washer cost me $383.40, plus I bought the matching dryer of $403.39. This makes zero since. Please advise.

I bought a Neptune washer and a dryer. I have had nothing but problems with these items since I got them. My washer keeps giving me a 3e code and will not clean the laundry right. I have used the H E detergent it requires and yet my clothes stink. My laundry smells like mold and mildew. I now dont have my units to wash and dry clothes. I paid almost $4,000.00 for the pair. I dont have the money now to replace them.

I bought a Maytag Centennial Commercial washer, 3.8 cubic feet, Model # MVWC425BW on September 17, 2014. My clothes were never clean and barely wet. The machine took almost 2 hours to do a load of clothes and they werent even clean! I bought the 3-year extended warranty through Lowe’s. Three years and 8 days later the machine stopped working. Serviceman came out and told me the washer was fatally wounded. He said the transmission failed. He also told me the replacement part would be $400.00 and that it wasnt worth it. He said these machines are junk and Maytag has had all kinds of issues with them. So Maytag knows these machines fail and yet do nothing for their consumers. Maytag, you will only ride on your name for so long; consumers are catching on. Maybe back in my Moms day you were the go-to brand but Im afraid that ship has sailed. Ive always gone with Maytag but now I question that choice. I came on Consumer Affairs page to see what brand I could buy other than Maytag. Seems Kenmore gets high marks.

Purchased a Maytag Bravos XL less than 3 years ago Model MVWB725BW0. We have had several repair calls. From reading complaints from others, I have the same: clothes balloon, clothes rip, dark clothes have a scum on them, even a blanket goes off balance and it is hard to start the cycle. It goes off balance all the time, makes a squeaky sound when agitating and the housekeeper can never figure out what cycle to run the clothes on because they always go off balance, there is a loud vibration, etc. The last repair call was for an actual leak on the floor! The appliance company charged us $95 for the service call, did nothing, and told us the parts would be more expensive than a new washing machine. Went to Home Depot today and purchased an LG washer and dryer for over $1500. I am not even going to try to recoup anything from Maytag because this is the second Maytag that I have had a bad experience with and didnt learn a lesson in the first place. Junk. :(

Bravos XL top loading washer looks nice and very large, but thats about how deep it goes. It leaves even a small load half-unwashed unless you select deep water wash and even then it FAILS TO USE ENOUGH WATER. I tried to go and fill it up once with tap water and it totally DRAINED THE WATER AND SOAP before it unlocked! It was on Deep water wash and the top of the load was totally dry as I dumped the hot water onto it.It is a bad design and it should have never been sold. I know it has special places designed only for HE detergents but when you try to use a Tide Pod the detergent NEVER FULLY WASHES OUT OF THE CLOTHES.... Too small a load, too big a load, exactly 5 pounds or exactly 10 pounds it really doesnt work very well - AT ALL! I was thinking that I might like to get some SHOS at the low price it is but now I can see why they are definitely not getting back into business.

Before putting clothes in dryer you have to untangle them. Sweaters and even t-shirts become stretched beyond help. Clothes smell like mildew if you leave them in the washer even just a couple of hours. Im 50 and had a few washer/dryers and these take the cake. Ive used the washing machine cleaner/refresher (something I have never done on washers in the past) and still a mildew smell. The dryer has lint on both sides of the lint screen. And as stated before if you dont untangle your clothes they come out in a big knot, partially un-dried & very wrinkled. The lint on both sides of the screen concern me - Ive never had a dryer do that before. Its not much lint on one side but enough to think something is not right.

Loading is easy, operation is extremely quiet, dishes are very clean even on normal auto wash cycle. White, integrated depress buttons, full size, removable utensil baskets, upper and lower racks, top rack is manually adjustable, stainless steel tub. White front which is what we want not the ugly old metal stainless steel, usage buttons are on the upward facing edge of the door, pull down handle is nice size and very sturdy. Model is MDB8959SBW3. Even on normal auto wash cycle dishes are clean without much pre-rinsing. Purchased 10/14 from local dealer and professionally installed. So far we love it.

We bought our Maytag dishwasher at Sears about 2 years ago. It has never cleaned very well, we have to rinse everything almost to the point of spotless before we load it. Its a water saver, which means it takes more than 4 hours to fully cycle. Just today, I went to turn it on and the start button does not work. I looked it up and found that this is a common problem with new Maytag washers. This is really irritating, considering we paid a lot more for the Maytag brand than we would have paid for something without the Maytag reputation. Live and learn, I guess; we certainly will not be buying another Maytag.

Wow! I wished I had reviewed this page before purchasing a Maytag. We bought a new Maytag Range (#MGR5751BDD) from Menards in March 2008. Within a couple of months, we were out of a stove. I was lighting the burner to make dinner for my family (it is a gas range) and all the burners started making a clicking noise and they caught on fire. Luckily, my husband was nearby and took the fire extinguisher to it.We thought for sure that the house was going to be gone. We contacted Maytag and they had a guy come out (wasnt the friendliest and cted like he could care less). He stated there was wiring that was bad but because we took the fire extinguisher to it we probably voided the warranty. What? He would submit a report to Maytag.Maytag reluctantly gave us some money but not near enough to cover the stove that was only a couple of months old. Now, I cant use the new range that is 2.5 years old. It pops and spurts because the regulator needs to be replaced. The bad thing is by the time we pay for a repairman and the new part, it will cost us a lot of money we cant afford. This stinks.

Our problem started when the control lock button locked itself on. Called Maytag and told it wasnt covered by warranty but they did walk us through resetting the power and it fixed the problem until we ran the next load. Now when you try and set it, the rinse only light comes on. Bought the Maytag because I always believed them to be dependable - wrong!! I had a basic model Whirlpool running for a family of 5 for 25 years prior to this Maytag without ever having to call a repair person. Maytag wont deal with the issue so I would recommend to anyone else having any issues with unreliable appliances to do what I am doing - boycotting Maytag!!

I bought a Maytag washer 1 year and 1 month ago (MVWB835DW1), Hated this washer since day one. It does not wash clothes very well, does not even cover them fully with water. The mini agitator at the bottom does not move he close it just spins on the bottom of them. Now it started making a very high pitch squeal when it spins and of course it is one month past the manufacture warranty so I call a repairman and the first thing he says to me is Im sorry for your purchase, it was a bad one and it will cost me 600$ to repair because the bearing is bad. And my bad for not getting an extended warranty but I have never had a washing machine work this bad and break within the first 13 month of owning it??? Lesson learned I guess!

I inherited this Maytag washer, so it has been around a very long time (I have had it for 18 years). It still runs quite well, has 3 levels of wash/rinse, 3 cycles to wash in. Both of us...me and the washer are still kickin together. Highly recommend Maytag.

We purchased a Maytag refrigerator and right away had a loud noise. Found out the ice maker was on even though we dont have it hooked up. Now our freezer isnt working. Food is defrosting and ruined. Bottom half of refrigerator is freezing everything. Our fruit and pop and water and lettuce all frozen. 4th time they came which is today. Now says our freon is low so well see what happens. The repairman was so rude he was yelling. We said our Popsicles turned to slush so he said, Dont buy any. He was so nasty. No more Maytag for us – waste of money. Even had the compressor replaced. Wasted 1100.00.

Bravos XL washer- This is probably the worst purchase I have ever made, first off, at $1000 it was a pricey purchase however, I chalked it up to it will last many years without issue. After only 3 years, the unit leaked water and was so loud you couldnt stay indoors while it was on spin cycle. The bearings and seal were completely shot and needed replacement, after the sticker shock of having a good repairman fix the problem I decided to tackle the job myself. (Thank you YouTube). All was well for the next 2 years until it all happened again. Maytag is junk and will never get another dollar from me-ever! A Speed Queen TR5 now sits where that piece of crap used to reside. BUYER BEWARE!

Maytag HE Top Load Washer - We bought our whole house lot of Maytag appliances 6 months prior to when we would need them, in Nov of 2015. There was a great Canadian Black Friday sale event special, so we purchased the whole lot at Home Depot thinking we had got a great deal, however back then there were very little reviews on the washers, as they were fairly new. This is the absolute worst washer, I have to pause the washer after the water level that the sensor allows finishes and add at least a bucket more of water to cover the clothes and clean them properly and rinse them twice to make sure the residue from the soap gets washed off (I use HE pods, so not using too much soap). Certainly not what you would expect when you buy a high-end appliance. Im going to replace it, but I cannot even try to recoup any money back, as I couldnt/ wouldnt be able to sell it to anyone knowing that it is just garbage!! You would think that a high-end appliance company like Maytag would admit that this appliance is a mistake and offer the consumers that purchased this junk a credit towards a washer that will do what is expected!! Think about it Maytag... you have lost a lot of future business by ignoring the fact that this machine is not what you advertise as a company that stands behind their name. I am sure to tell everyone that I know about the disappointment in this product. I have a friend that has a LG HE washer and it works great... so no excuses about water consumption regulations... its just not designed properly!!

Same problems as everyone else. Water not soaking the clothes, questionable load capacity, shaky (we have engineers in the house so there is no way they did not look for floor evenness as the stores/Maytag will tell you that you may not have done, complete bs) etc. Its absolutely horrible that were all now stuck with such a terrible machine. I really wish I had read these reviews before (I googled the machine earlier but got generic stuff and didnt stumble upon these reviews until much later). Maytag should take responsibility on this as retail stores do not take back appliances unless they are defective. The Bravos is definitely a defective product from the get-go though.

This product has cost us thousands of dollars in clothing!!!!!! We have a lot of pictures to prove this!!!! Greg Mackie Major Appliance does NOT back this product or US the consumer!!! We have bought THREE households of products from this distributor & they have NOT backed any of the products that they have sold us, or given us Any discount for repeat business or loyalty and have NOT Supported us in any way whatsoever!!!! We have spent thousands of dollars and have had NO compassion or support whatsoever!!!!!! We expect a full refund for this Failure of YOUR product & a NEW Machine that will CLEAN our clothing & NOT DESTROY it!!!!!! Very Disappointed in this Product!!!!!! We Will NOT purchase another product from Your Company or from this Distributor unless YOU make a conscience decision to make this situation Right!!!!! We Will Spread the Word about your Failure of a product & detour business from YOU & YOUR Distributor!!!!!! We have numerous other photos to share with consumers of how YOUR product has destroyed our clothing!!!!!

I bought a Maytag washer and dryer about 2 years ago. I’m on my second washing machine (one was replaced from Lowe’s not Maytag). The second washer has now gone out! First it was the lid lock and now who knows! The repairman can’t even fix it. Biggest piece of crap, stay clear!! My first set lasted 25 years. Poor quality workmanship and customer service!!

I purchased the gas stove in June of 2012 from Home Depot, along with a Maytag microwave (Model MGR7662WB4). Home Depot installed both items. After trying to reach into the microwave about the stove, the knob would turn itself on with me brushing up against it. This happened several times, and one time the flame shot up and I almost got burned. The last time it happened, I did not realize that the knob was turned very slightly and gas was coming out of the burner for several hours. If it were not for a friend stopping over, I would not have considered the odor being from the stove. I assumed that the drains were probably backed up and started to add cleaners to the toilet bowls. I had to open the windows for several hours to get the smell out. So I called customer service 2 times. The first person said I would have to pay for the call if the problem was not Maytag and I said, “Forget it.” Then I went into Home Depot and the salesperson in there gave me another number to call for service. They came last Friday and said that he had seen at least 10-15 calls about this and since the unit was working as designed and no recalls, there was nothing they could do. “Just wait and see if a recall would be put into place and I would be on the list to fix it. In the meantime just keep the knobs off (which I was doing already out of fear).” My sister just bought a Whirlpool gas range this summer as well and asked if I could try her knob and it worked perfectly. Again I called CS and was told they could not send me those at no charge and that it would cancel out the warranty. So I asked her what I have to do before I or someone else gets injured and she said that until there was a recall, there was nothing they could do. I told her I was going to contact Consumer Report as well as Pam Zekman on Channel 2 news in Chicago. End of story; I still have the problem and no knobs on the new stove. Anything you can do to help please contact me, and thank you in advance.

We purchased the washer and dryer set from Lowes about 5 years ago, and purchased the extended warranty fortunately for us. We had good luck with the washer for about 6 months, then we had to call problem service out because the washer filled with water but wouldnt do anything else. It took several days for the service people to come out and when they did, they had to order parts to do the repair, so we did not have a washer for a few days or a week. They got the washer fixed and everything was good for a few months, then our dryer quit working. We were told that the tub of the dryer had come off, so they had to order another one. So we were again without a dryer. Once they got the parts in the repair company that was sent out to fix our dryer, did not fix the dryer correctly so we had to call Lowes repair service to send someone out again. We have owned this set for over 4 years and once again our dyer has gone out. During all of this time, I and my Brother had to leave our job in order to be home and meet the maintenance people to fix both washer and dryer. I would not recommend this set to anyone, this is one of the worst sets that I have owned. I thought Maytag was a brand that you never had problems with, but we have had nothing but problems with this set.

We had a three-year warranty which expired. We used a repair once for a rusting Clorox basin. Now, the tub swings wildly on every wash and will not complete because we get the UL warning. Weve tried making sure the washer was balanced but confirming that nothing helped. Most expensive washing machine ever and shortest life apparently.

I almost didnt write this review because it is just a repetitive representation of this machine. I AM SO DISAPPOINTED with this machine! I had a Neptune and after a few years, it started to spew oil onto the laundry WHILE it was washing! It ruined so much clothing before I figured out what was happening. Came to find out, it was a glitch with the machine that the company SUPPOSEDLY, sent out notices about but I never received. Now the Bravos X... Bought to replace the Neptune, as it was advertised to replace Front loaders. Would accommodate a KING SIZE COMFORTER with no problem... Got out of one problem to get into another!!!From the beginning, I wondered how does this machine get the clothes clean? How would it was a king size comforter? It doesnt agitate like the other top loaders. I figured it was a new top of the line kind of technology. My clothes started to tangle up really bad even though I was not filling the machine over excessively. The clothes were staying dripping wet over and over again. It doesnt matter how much clothing is being washed, they stay super wet. I have to go through the Drain & Spin cycle to finish the cycle. IT GETS OLD!!!! I HATE THIS MACHINE!!!! Doing laundry is a HORRIFIC CHORE for me. This machine is TERRIBLE. NEEDLESS TO SAY, I CANNOT WASH ANY SIZE COMFORTER!!!After reading all these reviews, seeing how Im NOT the only one who is going through all these problems with this machine, I refuse to call any repair company! I wont spend another penny on this monster!!!! I WILL NEVER BUY ANOTHER MAYTAG ANYTHING AGAIN!!! Reason for this review... So anyone who is considering buying a Bravos X washer, think again. Hopefully you are doing your homework and will not make the same mistake we did!!!! Thank you for your time and attention to this matter.

I purchased a Maytag washer from Badcock. Within 7 months the control board went out. It was down for nearly 6 months. I had to use a laundromat until I finally rented one from another place. Now again months later the control board is out again (F2F3 Call Service). Due to long wait time luckily I have another warranty but am being told I have to wait 2 weeks before a tech can come look at my washer, and that they wont have a loaner or cant just get me a new washer being the problem is THE SAME! Spent hours on hold only to be told to wait AGAIN! I would NEVER recommend dealing with this company. They used to be top of the line, but clearly not anymore.

Bought a maytag dishwasher 04/12/2013...have been thru 2 control panels...Now installing a third...washer works great except for that!!! Model mdb8949sbb0.

Maytag dishwasher mdbh979sam1 - Every single one of the Maytag/whirlpool dishwashers with soft pushbuttons and LEDs will fail--check it on YouTube. They have a very thin printed circuit strip from the door controller to the brains, and this rusts through in a few years. You must buy the whole controller for $150, you cant replace just the ribbon. And youll be doing this every few years. Maytag disavows this if you call them. The design runs the steam past this ribbon, so it corrodes really fast. Get a real pushbutton or a real dial knob model instead. With this model, the issue shows up when the LED pushbuttons stop responding or randomly light.

I have on the Maytag dishwasher for about a year. Is very quiet, the dishes are not clean. I called three repair guys from Maytag. The first time they replace the pump. Second time the guy said he just had a designed machine is no good.

Very disappointed with Maytag Bravos XL, four year old unit with bearings going out. Quoted $400 + for repair. With two in the house, wash demands are normal. Quality is questionable to have bearings & seal going out in four years. Also you cannot buy the bolt which holds the Washer Motor Rotor Cover on without buying the whole $130 assembly. Daughter has Whirlpool brand with same problem. Seems to me this is a problem Maytag/Whirlpool should address. My old unit (that I wish I still had), worked for 25 years. Would not recommend these machines.

After researching the top-rated washing machine in consumer reports, we decided to spend the extra cash ($930) and buy the top-rated machine. Spending almost double on a high end machine, you would expect this machine to last longer than three years. The motherboard needs to be replaced because it gets stuck on a UL code near the end of the cycle. Now, we have had two people come try to fix it, and they said to trash it and buy a new one. Only three years! If I had paid $300, I wouldnt be so upset, but that was a total waste of money for it to last less than any machine Ive ever had. How is a consumer supposed to know what a good washing machine is if they spend extra cash for the top-rated machine and that one is still bad? The company should replace something like a motherboard that goes faulty when it had nothing to do with use. So unfair and frustrating.

I have been reading the recent comments about the Maytag Bravo I purchased in 2011, and is sitting in my laundry room broken down. The timer wont advance past 18 minutes. I have reset it to factory default a number of times to no avail. I am very frustrated that the customer service offered an extended warranty for $319 to cover the service repair and another 1 years warranty. My washer is three years old! The warranty they offer is half the cost of the purchase price! The quality of this machine is very poor. I am truly disappointed with Maytag, who used to be a company you could trust. They have lost my trust along with my business.

So disappointed in Maytag - I have a 2013 Bravos washing machine that if I had it repaired again (less than a year after I had it repaired the first time and just over two years since we brought it home) the cost is going to two times the purchase price. And because it is just out of warranty Maytag is doing nothing about it, even though they know there is a flaw in their design.

I am angry at my Maytag! It sprays water on clothes that is not enough to soak them or let the detergent to be dissolved especially for towels. Hopelessly, I Hand Wash my towels, rinse in tub then just put them in the machine to spin. BAD BAD :( :( Is it possible to increase the water amount?

I purchased a Maytag dishwasher on Nov. 5, 2013 from Freds Appliance. I had to have the control panel fixed twice and it failed again in June 1916. My stemware had a film on it and I either had to wash it by hand or rinse it in hot water and dry by hand. Thus I felt like how could my other dishes not have this film on them even though I faithfully used Finish. I have 2 daughters who live within a half mile of me and they did not have this trouble with their dishwashers. I always felt Maytag was a top brand, but I replaced my 3 year old Maytag with a Whirlpool that my daughter and her family of 4 used for 19 years. Guess what... my glasses come out sparkling without using Finish and they wash in half the time and are dry!

My parents always bought Maytag and so did I. Ive experienced minimal problems in the past and have done my own repairs. My new MDB4949 dishwasher is GARBAGE! Imagine coming home and seeing water flowing out of the house under your back door! The water was coming from the kitchen across the kitchen floor and cascading down the stairs like a waterfall. I pressed the cancel button, nothing? Opened the door, NOTHING! Shut off the circuit breaker, NOTHING!Water continued to flow until I closed the supply valve! The dishwasher damaged my home! Six service visits later and still not fixed! 9 days out of warranty and still having the same problem! Customer service told me to hire a plumber to fix my plumbing problem with the dishwasher water supply! Thats funny because 3 other dishwashers (in the same exact place) had no problem with the water supply in the past 23 years? Two of them were Maytag!I never give less than a positive review but, this is outright FRAUD! The dishwasher has damaged my home on 2 occasions! Unless I want to stay home the whole time its running I cant use it? The customer service is pathetic at best. The control board issue is a scam by every company. Its all designed to keep you on a service plan and is a scam! Long gone are the days of the reliable rotary timer/control that lasted forever! You can thank everyone you know for not paying attention and letting this happen! I guess we can wash our own dishes by hand or comply with this obvious scam?

Maytag Bravos XL - I am having the same problem as everyone else with this washer. My clothes do not get clean and they smell. Maytag advertises tumbling, rubbing action to get clothes clean but my washer does neither. The clothes lay in the bottom of the tub and never move except when in the spin cycle. I am going to file a complaint with Maytag and if they do not refund my money am going to file a DTPA claim against them for false, misleading and deceptive advertisement. They will have to pay up to three (3) times the purchase price of the washer. Maybe everyone else should consider the same.

My Maytag refrigerator was purchased from Home Depot less than 3 years ago. It is a French door, bottom freezer draw model #MFI2569VEA1. Every four days, there is a huge puddle of water at the base of the unit and it is starting to ruin my ceramic tiles. I tried the online video solutions to no avail. Home Depot wont repair it, they told me to contact Maytag. Maytag wants me to purchase a $375 warranty, which is 30% of what I paid for the refrigerator. I will never buy a Maytag refrigerator again, or any Maytag product for that matter. They once stood for solid reliability and peace of mind, now you get a piece of junk instead. I cant even sell it on Craigslist if I wanted to because who would want it? If a class action suit is ever initiated, Ill be on board. I hope Consumer Affairs contacts me.

This Bravos washer and dryer saves energy for sure, but sadly, that is it. It does not wash my clothes and rinse them adequately. They are so twisted and wrinkled I have ironed just about all my clothes. Even my synthetics are severely wrinkled. The dryer sensors do not work. They never dry the clothes adequately. The concept was good in that they are compact and have a large capacity, but the design does not work. I was lured in and unfortunately, there were no reviews at the time but I see that everyone shares my sentiments. The washer and dryer are just not any good. Thank you.

I also am the unfortunate owner of a Maytag dishwasher Quiet Series 300. I bought it in April 2006. The control panel has been a problem since the first year of operation. Typically, one of the indicator lights would randomly go on and off during the machines off mode. At other times, the control panel would not operate. However, if I waited a few hours, it would dry out, enough and then would operate. Apparently, steam leaks into the control panel and causes it to be erratic. This has been a problem with this design for many years and the Maytag Corporation has not cared enough about its customers to correct the design flaw. I remember when the name Maytag indicated a top of the line product. Sadly, this is no longer the case. As a result, my loyalty to them has ceased.I probably will not buy another Maytag product again. Their standards have eroded.

I would bought a Maytag Aqualift self clean oven. I just ran the clean cycle and it is just as dirty as it was before I ran the cycle. Absolutely nothing happened. Now I have the 2 cups of water at the bottom of my oven they said to put in prior to clean cycle, that I have to get in and clean out. This is absolutely unacceptable. I would like Maytag to get back to me asap and offer a solution. **.

Bravo XL - I purchased this dryer in June 2012. In October, the first thermostat was replaced, again in February 2013 and two within a week from March 8th and March 12th. I was told it was my vent. However, the appliance continually showed venting good. I was told to have it cleaned. I did and it is documented that there was great air flow before and after and only a handful of lint collected. I have spoken with Whirlpool and no one will have the integrity or courage to say it may be a faulty unit. I will never purchase another Whirlpool product. I had spent nearly $5,000.00 in Whirlpool appliances in June of 2012. I feel they will cover any issues until the warranty is completed, and then the problems are mine and at my expense.

We purchased a Maytag Gemini gas range last year in April and the extended warranty. The ovens have not worked correctly since we bought it. I never do this type of thing, however, I am just disgusted! I am going to exercise my right as a consumer to express my customer dissatisfaction and share using the social network. I dislike Maytag and even dislike A&E factory service more! I have never experienced such bad service on a new appliance. What is even more concerning and the reason I am posting this warning is there appears to be no recourse! I googled search both companies and the first things that came up were complaint pages. How sad! Buyer beware! If you buy a new appliance, research the warranty provider. It appears that Maytag has laid off the Maytag repairman and went to a lost cost unskilled service provider! A&E repairman has no idea how to fix the oven. He replaced the part. 4 weeks later, came out and walked in the house and did not even look at anything and ordered the same part again. He told us he would be back the following Friday. He did not schedule an appointment. I called on Thursday before he was due to show on Friday and A&E told me I had no appointment scheduled. They told me to inspect the parts that were shipped. I told them I would not even know what I was looking at! They told me the repairman would be back out between 1-5PM on Friday. No one showed. At 2PM, I called and A&E said the repairman must be on his way because he did not call and say he wasnt coming. But again, he did not show! I made no less than 6 calls to A&E and Maytag after that! A&E would not escalate the situation to a supervisor and on call number 6, when I finally got to an advocate, they told me to call Maytag! I have taken 4 days off as vacation to be home for the repairs and this last day was the final straw. When I researched escalating paths for both companies on Google, the first thing that came up was whole pages dedicated to complaints for both companies!

Thank you all for taking the time to write these reviews. My only regret is that I am reading it now, I wish I would have read it before purchasing my own Maytag washer and dryer... I bought a Maytag MVC565FWI / YMEDC555DW1 washer and dryer duo in December 2018. I had some holes in my sons clothing, but thought maybe they were due to him being a boy of 17 year old in college, sitting all day... Also my dryer was barely drying.Called and had a 1st technician for the dryer issue. He said no wrong code and to try and clean the evacuation vent. As I am a renter, I contacted my owner to do so and he did. But I did not get to try the machine unfortunately since 5 days after the technicians visit, I was deploying to Africa. I am military and was deployed for 8 months. Upon me return, dryer still barely dries and HOLES in every load of laundry that I do. My sons and also my own clothing. This time, there is no mistaking articles that I put in came out with huge circular holes.A second visit with a technician is arranged, last Tuesday October 8th 2019. Still no codes are found. And technician suggests cleaning the conduct better. Again my owner does so. Again, up to 4 cycles of 60 min on High heat to dry articles. No economy on energy on these models! I have called Maytag today since no one has contacted me in a week for my wrecked clothing. To my request of having my appliances either replace or refunded, they say no. Policy is to send a technician. Again. After 2 visits of technical support, Maytag is sending me for a 3rd time a technician (at my cost if nothing is found again) to test the appliances. Since the technicians can not find a code on his machine, Maytag is telling me they will do nothing.I have a washer dryer that wrecks my clothing and does not dry them. (Also I feel like my clothing are never fresh scenting, I wonder how efficient they are with even the basic cleaning part..) I will have to put them in the garbage, because how can I sell them?! Talking to Maytag, is being treated like an infant that does not understand THEM, when in reality, they do not back their products at all. I feel left alone with brand new machines that have been used around 30 times in under 1 year, that I will have to through away in the dump and never ever buy from this company again. M.

wW have had this Maytag gas range for twenty years. It has performed well for that length of time (maybe longer). During that period I replaced one burner. Only complaint is that the oven does not heat as quickly as I believe it should.

We bought a Maytag Gemini double oven in June 2007. It has been a problem from day one. It arrived with a damaged door. They reordered and replaced it. Through the next few months, I became very discouraged with the oven. I bake a good bit and was always used to an oven with fairly accurate temperature. This oven will not reach or sometimes just wont maintain a steady temperature. After a couple of service calls, I gave up. I now raise the temperature setting about 50-75 degrees higher that the recipe requires. Naturally, I dont always get the best results. However, that isnt the thing that really bothers me. These ovens have three ignitors. About every six months, one breaks. The cost is over $200.00 each time. The ovens/broiler are highly unreliable. After mixing up something or on an important holiday, one may find that the oven wont light. Theres no warning! It is simply gone. I will never again buy a Maytag! I called Maytag and questioned them about the lemon law. I was told that the same piece had to break three times in one year. That is crazy, when the entire thing doesnt and has never worked well.

I bought a Maytag Bravos XL washer in 2017 for around $800 which suddenly stopped working about 1.5 weeks ago. The console wont turn on. I filed a service request on Maytags website which results in Maytag subcontracting the job to a local appliance servicing company. About 10 days later the appliance tech shows up to my house. I had to pay $125 to the service company for the technician just to show up. After, he tinkers with the machine and 5 minutes later gives me a quote totaling $789.07. Of that amount the parts component was $482.09. He told me that the computer was bad. I was appalled. This was a 2.5 year old well kept washer. I called Maytag company next day to see if they could at least cover the parts cost. Especially as I have a large family with 3 kids plus elderly family members. After waiting 33 minutes on the phone, the CSR took all the appliance info and tried to see if she could get Maytag to cover the parts cost, given my situation. After about 5 minutes, she told me that Maytag declined my request- quoting that my appliance did not have any warranty and that the notes on the computer regarding my appliance indicated that it was field scrap. Field scrap?? Really? This was an appliance that was bought at Home Depot.This is the lowest of lows that this company (Maytag/Whirpool) can stoop. For a billion dollar company, that are advertising their products as Made in America, they have no heart and no empathy for their customers. They build sub-standard products comprising of cheap parts so that their products only last a few months, then they try to sell you their sub-prime warranty services that are full of holes. And for those poor souls that dont sign up for their warranty services, God help them if their appliance breaks down. They are then left to deal with Maytag/Whirpools appliance service vulture contractors which in tandem with Maytag conspire to squeeze every last cent out of hard working Americans (Especially during these trying times).Just to compare my situation. My parents bought LG washers and dryers in 2008 which remain in full working operation to this day (12 years in operation). The Maytag Bravos broke down in 2.5 years. Use my experience as a lesson. Do yourself a favor and save yourself the headache and heartache. DO NOT, I mean DO NOT purchase or support Maytag/Whirpool appliances. You are better off spending your money with LG or Samsung.

We just had the same problem as most of you have posted. The control panel malfunction. Model MDB7749SBM. Our issue started after only 18 months when the dishwasher would start on its own and/or cancel a wash on its own. I think this is a major issue if a home appliance can start on its own from the off position and run through multiple cycles. I think this could be dangerous if you are out of town. Our cost to replace the panel was more than 1/2 of the original purchase price. This is a major defect and should be handled by Maytag if they are a company with any integrity.

I bought my first Maytag French Door fridge about 7 years ago. When it was two it started running water on the floor. I paid a service guy to tell me a tiny little drain in the back clogged up and stopped coil defrost water from draining out. He fixed it. A year later, the fridge stopped cooling but the freezer was cold. I hired another service man who charged me a mint to diagnose that a fan that blows cold air up into the refrigerator failed. Rather than pay him again, I ordered the part. Heres the joke--the part wasnt available. An older part was substituted. Why? The first fan motor was small to make the energy start requirements--but it was too weak to be reliable. The new motor was an earlier model--almost twice as large and powerful. So much for Energy Start. At exactly 5 years and six months, the compressor went out. Im on year two with the new one. I said to myself they cant all be that bad. Now it is leaking on the floor. I have to disassemble the freezer, remove the inner wall, defrost the coils and clean out the drain hole. Wouldnt smart engineers make an easy way to do that from the back? Seems simple.

We purchased our Maytag Neptune Washer and Dryer approximately 5 years ago. Over the past year or so, Ive noticed an odor coming from our washer and it’s becoming stronger. Water is staying in the drum and there is mold growing on the rubber seal when you open the door.

I bought a Maytag Dishwasher Model #MDB7749SBW2 in 2013. It worked great for 2 years. In 2015, the control panel malfunctioned. All the lights on the control panel would light up and the dishwasher wouldnt start. I called Maytag. They sent out a service tech. He replaced the control panel. I started having the same problems two years later, 2017. I called Maytag today, 9/11/17, to see if they had recalled this dishwasher. No, it hasnt been recalled. They offered to sell me a extended warranty for $400+, that would pay for the service call and parts or, I could find another Maytag, Whirlpool or KitchenAid dishwasher and depending on the model, I could get a 25-45% discount on a new one. I asked why they havent recalled this model, due to the problems that so many people are having. They dont know. Im writing this review to let those of you who have bought this dishwasher know, that the product is faulty.

I purchased this washer on 5-25-15. It was delivered on 6-2-15. It worked for 11 days. On the 13th, I called Maytag and made an appointment for it to be fixed. They said a technician would be out on the 16th to fix it. I got a call on the 15th saying the part they needed was not released yet so they would be out on the 23rd. The guy comes on the 23rd and diagnoses the problem. He says the machine has a bad motor and shock of all shocks. He doesnt have the part to repair it. They originally assumed it was something else and were wrong. Fantastic. He said he would be back on the 30th. I got a call on the 29th saying that, once again, the part needed to fix it was not released and that they would call me to make another appointment when it was available. I had enough. I originally purchased with Home Depot and called my original salesman. He told me he would replace the washer with any brand I wanted (I paid the difference in cost of course) but I was still relieved that he was willing to work with me. I ended up going with an LG. Lets hope that one works. I have 2 kids and have been having to go to the laundromat. I have to say that I loved the machine for the 11 days it worked! I would probably still have it if they had better customer service but Im not going to continue to put up with them not having whats needed to fix this thing.

I bought the Maytag Bravos X, last year. The silver color and glass top fooled me into thinking this was better quality than it is. This washer is very easy to go out of balance. I had to open the top (easy) and install/glue a little styrofoam, to limit the amount the tub could travel. Second unresolvable problem is how to wash anything larger than ONE outfit. If you watch the videos, and read the information, this washer is supposed to flip your clothes so whats on top makes it to the bottom for agitation. Ha! Absolutely BS. Unless you wash a very small load single level. The clothes in a TYPICAL size load will sit exactly as you loaded it.the only attention the top layer of clothes is only sprayed with water, no agitation. Hope you dont have kids. Doesnt XL mean extra large? It sure does, you can wash one pair of extra large pants, and or one extra large shirt.

Maytag in general has gone from being reputable in the early 70s to being the epitome of a rip-off company that sells junk, then refuses to stand behind it. I have a Maytag Washer and dryer. The washer continually goes out of balance and spins across the floor. Repair people tell us that our floor is not strong enough - funny, our new Samsung washer has no apparent issues with the floor or anything else. Our Maytag Gemini is a piece of crap. The ovens do not work or heat up most days. Maytag pushes replacing an EOC board at $800.00, but then the part is not available. Stove is not even six years old. Maytag is a synonym for junk.

I wish I had never bought a Maytag refrigerator! Nothing but problems. The ice maker does not work, water leaked 3 times onto our wood floor. Finally, I disconnected the control panel so I have an ice/water dispenser that is useless just like the refrigerator. I dont think the Maytag man is sitting around from lack of work, maybe laziness. Dont buy a Maytag.

Bravos 4.3 High Efficiency Washer - The worst washer ever. I recently returned from burying my step-mother. She actually used the same washer and dryer, by Maytag, for over 50 years. Those days are gone forever. This is my second set of Maytags in ten years. The first literally stopped working just after the first year warranty ran out. I still have them inside my pantry, like a set of anchors. Notwithstanding that, I thought, Maytag was a good brand, it must have just been the style of machines, so I purchased these in January. After over six months of usage, I am amazed at how many times I have to wash a single load of clothing to get the items clean. Who cares if the machine saves water? What was wrong with having an agitator? I literally have to remove freshly laundered clothing, turn it over and run the wash again to get the top of the laundry clean. I have had a blanket finish for the fourth time to get it clean, only to have to hang it outside because it is so full of water, the weight keeps it from spinning properly. And why would you remove a timer feature which permits very busy, working people, to wash their items while they are on the way home or in the middle of the night so that there is no waiting to pop the clothes in the dryer? None of the cycles takes less than 80 minutes to complete. Who has 80 minutes to wait on the washer to do its job? I am so upset about the amount of money I spent on all of these machines. Just think, I could have brought the over 50 years old set home from my step-mothers and had a washer and dryer do what they were supposed to do -- clean the clothes.

I purchased a Maytag dishwasher Model # MDB4949SDE1 from Home Depot April 30th 2015. This dishwasher does not clean the dishes no matter what cycle you use. After 4 hours and 29 minutes I open the dishwasher to find residue on my so-called clean dishes. Every time I use it I have to re-wash or rinse the dishes by hand before I can put them away.I have spoken with Maytag on several occasions concerning this matter. I have used every detergent on the market. Maytag says you have to use jetdry, and liquid detergent which I did and it made no difference. The latest suggestion was that the water from my water heater was not hot enough which is set on 140 degrees. The customer service rep. ask me how far the water heater is from the dishwasher and I replied approximately 14 foot. She suggested I turn the faucet to my sink on before I turn the dishwasher on so that the hot water is present as soon as I turn it on. This also did not work. They sent a kid out today that turn the dishwasher on for five minutes empty and said well everything seems to be working properly. I dont know what to tell you, yet there is soap residue in the bottom of the dishwasher right now. Do not purchase this dishwasher. It does not clean the dishes. It just uses power and water.

I bought a Maytag microwave model mmv4203ds00 on May 2010. On 8-20-10, the microwave stopped working. It was serviced under warranty. However, on 10-31-11, the microwave stopped working again.

We have had our washer and dryer almost 18 years and just recently spent less than $280 to get the washer going again. The dryer we haven’t had serviced yet. Great quality. So worth it. Our Maytag appliances are used frequently and keep giving out the best performance.

I found this washing machine reliable for over 10 years. I paid more for this brand but it was worth the extra cost. I found this washing machine Simple to use. I would recommend this washing machine.

Dishwasher cleans well, but the control console has failed again & only responds to two functions. After replacing the console a couple of years ago with a new unit I thought it was done (it didnt get much use). Is there any recourse for this complaint? All I want is a new console panel. Maytags brand is apparently only good on the commercials. Very disappointing. Also, the top rack is very awkward & is only good for short glasses etc.

Dryer doesn’t dry any size load in one cycle regardless of settings. Mysteriously, it triggers a message to check the lint filter and line when running a small load with nothing blocking the venting system. It never happens on large loads which would block more of the air flow. You could get a comparably sized dryer for much less. This not the premium product that you pay for.

I purchased a Maytag refrigerator on April 4, 2012. This week, July 12, 2015, my compressor went out. I called repairman and he said the compressor was shot. I thought this refrigerator would last longer than 3 years. I had to go purchase a new refrigerator from Home Depot in Knoxville, TN at a cost of $1,057.95. I am 80 yrs. old, on Social Security and this was a lot for me to put out, since the Maytag should have lasted a lot longer than 3 yrs. I feel I am entitled to some reimbursement. The Maytag is a side by side, Model MSF25C2EXB00, Ser. HR21112159. Im disappointed in Maytag and will never recommend or buy another one.

This dishwasher is reliable and has NEVER had any repairs. It cleans fairly well, but I do wash off dishes before I put them in. The one complaint I have is sometimes the dishes smell funny after washing. I think it may be our water though. I also like that there is room for oversize dishes and glasses on some of the racks. Overall, I would buy it again.

Maytag Dishwasher MDB7749SBW03 - We purchased this dishwasher in 2013. About 1.5 years after purchase the control panel started to get flaky and different settings wouldnt work. Not long after that it stopped working at all. I did some troubleshooting and found that the ribbon cable that connects the control panel to the control board was corroded due to water/steam getting to it. Since we were past the one year warranty I bought a new control panel and things worked fine for about a year, now the panel is going bad again. I contacted Maytag and they said they cant do anything to help me. This machine is not even 3 years old and going on its second control panel. I would recommend staying away from all Maytag products.

It doesnt agitate enough to move clothes around. Doesnt put enough water in tub, even on deep fill just barely gets to the top of clothes. Washed a shirt 3 times by myself to get dried mud off of it. 3 time it was washed bumy its self. Clothes do not to get as clean as they did in the old style washers that had good agitation and the agitator that was bigger than whats in these new ones. And water. Need water. We arent trying to dry clean. And even thats done with a liquid that totally covers clothes and moves around better than this garbage I have right now... Looking for an old washer to replace this one... HATE HATE HATE THIS WASHER.

Purchased new Maytag washing machine July 17, 2011. Have had several problems with it over the past three years. Most of the time it would not complete a load of laundry and would get stuck before the drain and spin cycle. Last week, the spin cycle became extremely loud. Had a repair person come out and was told the motor bearings were bad. Estimated repair cost $700. Purchased this unit new for $569.00. Called Maytag, was told that 10-year warranty on drive motor and wash basket did NOT include the bearings. Asked if they could help out with repair cost, was told no. Will never purchase another Maytag product again as they do not stand behind their products. Household has 4 people in it so use of this machine was light to medium.

I have owned a Maytag gas dryer for 10 years now. I have had to replace the idler and belt 4 times now. This dryer appears to be built as cheaply as humanly possible just to get it past its almost non existent warranty. The replacement parts are even worse. The idler has a bronze bearing in it as a wear item. Really??? Why was this never even considered as a part that could be lubricated at least occasionally?Granted, lots of people do not have any mechanical ability at all and just pay through the nose for a repairman to come to their place for any repair then pay dearly for the service but, I DO have mechanical ability so I do all the work myself. That is why I know firsthand about the terrible manufacturing results and the very cheaply built replacement parts available at outrageous prices.

Dishwasher MDB7749SBM - Have the same problem as everyone else, panel board (2nd one, 1st was under warranty). This panel W10475787 is 2 years old. Keeps lighting up doing what it wants to do. Dishwasher is 3 years old. Cant find out if there is a recall on this part (there should be).

I bought a Maytag Top Loader. I soon discovered that it is not possible to do a cold water wash. After much communication with Maytag Customer Service it was determined that there is no way to bypass it. And it uses a lot of hot water, even on a cold wash. Their explanation was that the water needed to be a certain temperature to make the detergent work effectively. The same detergent that I’ve been using for 40 years with cold water in my Speed Queen. When I need to do a cold water wash, I go to my parents home and use their washer. Disappointing purchase, my last Maytag, for sure.

I have had this machine for 15 years and never spent a penny on any maintenance, I love it. Some things are worth it and it still has a stylish look and cleans great. The only thing I would change is if it didn't have any the middle washer paddle so it would have more space like the newer models.

I purchased a MTW6600TB0 Washer and Dryer on 6/17/07. I have had issues with the washer from the beginning; smell in towels and mechanical problems as well. The machine does not fill properly and receive error codes that are electrical issues per A & E service. I get LF errors occasionally and randomly on different cycles. I finally called for service because I now am receiving F51 Error, which has to do with the basket per A & E service technician. I was told on Black Friday that my machine required both baskets and the rotary motor. My machine is just 4/5 years old. No unusual wear and tear. There are only three people in my family and we live in a fairly warm climate so no heavy winter clothing, etc. I was told that my stainless steel basket was rusting to my plastic basket. I am still trying to comprehend the fact that two materials that are not supposed to rust are rusting. After looking for a new washer over Thanksgiving weekend, I find out that Maytag warranties their stainless steel basket and rotary motors for 10 years. So do they warranty the things they say the warranty or not? Of course, it is a holiday weekend and I cannot get a hold of Maytag. I paid for a service call and the technician told me I would be responsible for the repairs at about $500 for parts plus labor. I looked up the parts he recommended replacing and it was over $800. I paid $1000 for this machine less than 5 years ago. Thats $200 a year for the privilege to use a Maytag. Additionally, my set is black. I can not find a black washer anywhere.

I have a Maytag washer and dryer. The washer is a top loader with a metal drum. You can hardly hear the washer while it is running, and I have had no problems whatsoever in the past six years of ownership.

In October 2016 I purchased a New Maytag washer (Model# MVWC565FWO) from LOWES. I bought an extended 5 year warranty with it as well. I have my invalid, totally incapacitated Sister living with me. The situation requires several loads of washing each day due to her conditions. TWO WEEKS after starting to use it we began having issues with the washer. It would stop in the cycle, lights flashing, only way to restart is to unplug it, move control from wash cycles setting to drain and spin... then within the next 3-4 loads it would do it again. Sometimes it sat for awhile I would smell like an electronics Odor getting hot... I called Lowes. They replaced it. Approximately 3 weeks later the NEW washer began doing the SAME THING...Lowes would not replace it with a different Model or brand... only send a repairman out. Long story short, he has been here 4 times, replaced the Computer Control with NO IMPROVEMENT!!! NOW Lowes is sending him out again and saying that if this doesnt fix the problem they will refund my money... My problem with it all is this... IF MAYTAG is having these type issues, WHY PRAY TELL, has a recall or solution been found and passed on to the repair folks??? I bought this Maytag due to #1 Reputation, #2 It was Assembled in the USA, NOT South Korea like the Samsung with recalls... Now all this is going on. I WANT A WASHING MACHINE THAT WORKS RIGHT!!! This is totally unacceptable and totally uncalled for. WHY could these Govt agencies and Manufacturers not LEAVE the washers alone? Computer technology... PLTTT. The old timers controls gave no problem in over 40 years of using them. Now this crap.

Washer stopped working, never did clean clothes. Out of warranty - some it is fix or buy a new one. DONT BUY!!

For years I wanted a top loading Maytag washer. Last year I bought one at the cost of £720 plus VAT. Started using it last July and in November this year it broke down. The company I bought it from said, Sorry, youre out of our warranty... Really! Here’s some people who might fix it. Eventually Hotpoint took it on and honored a two year warranty. Since November I’ve had an engineer out twice. Still isn’t working. Won’t replace it because it’s now discontinued, so more parts ordered. Engineer advised me to go buy another washer. Thanks Maytag for totally disappointing me in what I thought would be my perfect washer. I will continue to email etc and hope that someone will help me. No point in phoning because no one listens. MY OPINION - DONT BUY AMERICAN PRODUCTS IN THE UK AS NO ONE CAN REPAIR THEM PROMPTLY IF AT ALL.

I was pleasantly surprised that this basic model would work so great! It really gets the dishes clean. It came with the house so I did not choose it and probably would not have bought it if I had to shop for it.

March 31, 2013 a Maytag front loader washer series 2000 was purchased. In January an error code E4 and F3 kept stopping the washer. Service replaced some minor part, worked for a week. Then service replaced a circuit board - worked fine for a few months. About June of 2014 the codes came up again. This time Service wants 430.00 for a 700.00 dollar washer to fix a continuing issue. So I decided not to spend the money. I could buy another washer, different brand of course, and try and fix it myself. I removed the top and the bottom front covers. The 3 wires going into the circuit board that was replaced were loose, barely plugged in. The catch all at the very bottom right had derbies and coin in it, cleaned that out. Looked at the motherboard with a magnifying glass. It had no bad solders, cracks or burn marks, so I proceeded to run my hands around the entire drum inside... and in the back side where you can’t really see were some more loose wires.... tightened them. Now with the spin rpms you can understand how things shake loose, I always look for the common sense issues.... I am currently on my third wash load. It runs smoother and quieter than it did when it was first installed. Point is the Maytag service sucks and with only a year warranty from the manufacturer. What did I have to lose to try and fix it myself. I am sure this is happening with a lot of other people. The odds of a motherboard or a circuit board going bad in such a short time made no sense. So check all the wiring FIRST. Make sure everything is securely plugged in. I would not recommend anyone buy a Maytag or Whirlpool (owns Maytag) for their reliability or service.

After the 4th service call Maytag wanted a 2nd company to look at it. So on July 27th A&E out of Bristol, PA came out. He checked it out and said its not serviceable because theres a leak somewhere in the casing. Had to call KYW 3, On Your Side, they helped me get some progress. Jacqueline from corporate called and said they would replace it. It started on July 3 and now August 13 and still no fridge. Had my Maytag washer fixed, small problem. Parts came in a box marked Whirlpool for a Maytag washer from a Sears Warehouse. Plus the mechanic said my Maytag refrigerator is made by Amana. Buy American?

After a year, the plastic parts of Maytag dishwasher is breaking and upstairs propeller is no longer running. Do not buy this product. I made that mistake.

We bought a new Maytag top load washer March 2018. July of 2021 it starts making the worst racket Ive ever heard. I thought at first that there was a dog being killed by another animal. As I ran to the door I realized it was my washer. Long story short, repair guy said itd be cheaper to just buy a new washer. Maytag did nothing to help us resolve the issue of a 3 yr old machine totally useless. We bought this machine because we thought it would last for years. I mean their commercial shows the repair guys doing nothing because Maytags never need service. My new machine is not a Maytag. No more Maytags for me.

Purchased washer in Jan 2013. Average usage is 1 load per week. Last week the washer started leaking from the rear left side. A service call discovered that the bleach dispenser was filling up with water and overflowing. Bleach dispenser?? I never use it! Seems that the new bleach dispenser hose line has a relief valve whereas the original part did not. Internet research has confirmed that this problem is very common with this make and model. However, a call to Maytag requesting what compensation, if any, would be available resulted in a response that basically was too bad... so sad... cant do anything for you! Seriously? An apparent common, known problem and all they can say is we understand your problem. Needless to say that will definitely be the last lonely repairman Maytag that this household will purchase.

I purchased a Maytag washer 5 months ago. I noticed the washer was not putting enough water in the machine to cover my clothes, and at the end of cycle my clothes would be all tangled up. A repairman looked at it and said there was nothing he could do. Do not buy this washer. It is a lemon. I even spoke to the main customer service representative, he was the most arrogant man I have ever felt with. He basically said deal with it. I want. I want my money back so I can purchase a washer that actually works.

After 18 months of use Our Maytag Dishwasher (MDB7749) has the same control panel problem as a lot of other user complaints. I wish I too had read the consumer reviews before my purchase. We will never buy another Whirlpool product!!

Purchase this machine Bravo XL Top Load Washer in Dec of 2016, noticed right away every load of dark clothes comes out of the washer with a scummy lint residue on them, some of the clothes are not completely wet when you take them out of the machine. Have talked to Maytag and tried their suggestions that did not work. Seems like a canned speech reading some of the other reviews. I am just at upset with the appliance store that we purchased this from after their sales pitch how these are the best machines made, made in Ohio, great company etc..etc.. Just one run around after another.

In 2006, my wife and I purchased a new Maytag refrigerator, the model type with the freezer in a drawer near the floor and the drawer is under the main door of the fridge. The thing has a sealed system and has a freon leak which makes it nearly impossible and not financially prudent to try to fix. Two repairmen were out and I spent $200 for them to tell me the same bad news. Its unbelievable that this junk wouldnt even last ten years. What is this, Russia? Ive heard some of their awful appliance experience stories and now this can join them. The reliable Maytag repairman who never has anything to - you know the one. He is probably dead. Hes not really the one to blame here though, it is the reliability of Maytag that is dead and will remain so for as long as this company is alive. Dont ever trust or buy Maytag if you care about making your investment in new appliances last! Dont do it, people!

I purchased MVWB955FW (washer) and MEDB955FW (dryer) from AJ Madison and the units were delivered in December 2017. After using the washing machine 5 times the glass lid spontaneously shattered putting glass into the machine and all of the clothes. I called Maytag for a replacement/service and they had to reschedule as the lid wasnt in yet. A week later, I followed up with Customer Service only to find out that the replacement lid was also shattered. They didnt make a replacement lid without glass (not sure why you need to watch the clothes being washed). I was told that there were no replacement lids available anywhere. I asked about getting a replacement washer and was told couldnt do that.I asked them to pick up the units and refund my money, which they promised. It is now 2 months since the original call for service and I continue to have to follow-up with them (never get a call back) and STILL have the broken units in my house. I have since purchased a replacement set (LG) and waiting for my refund. I will NEVER do business with Maytag/Whirlpool again.

Bought a Maytag refrigerator from Home Depot about 2 years ago. Like everyone else we are having leaking problems from the freezer drawers. I wonder if anyone has had it repaired and whether it was repaired

We have a Maytag Neptune washer we purchased new in 2001. The Neptune was useless on My mechanic clothes, but good for delicates and blankets so we have an old style washer to clean my regular clothes. The Neptune was at work on a blanket when we smelled it burning. With it unplugged, I got around to investigating the situation and found the motor control was shorted and burned. I tried calling Maytag. I was asking about an upgraded part or recall. They didnt want to help. The representative was condescending and after I listened to her attitude, she said someone would be in touch. NOTHING. Now I see these suits and I guess I understand. My house could have burned down - they dont care. Maytag is garbage and Im sorry I ever thought otherwise.

My old Maytag is still working after 20 years but my husband surprised me with a new pair! Washers is just pure junk. Not enough water to hardly wet the clothes. They just rub together and get worn out looking, towels are rough and not soft but my biggest complaint is the AWFUL wrinkles! I have to iron everything! Only had it 3 days, called Menards and asked if we could return for an exchange or upgrade and they said no. If this is the best American Made has to offer, then I will look at the Samsung! Shame on you Maytag. Not one good review on here and you do nothing to restore confidence in American Made. I will spread the word - NEVER by a Maytag or an appliance from Menards. Neither one stands behind the piece of junk!

I bought my Bravos washer (Maytag Bravos Model # MVWX700XL2) back in 2013. Worst mistake ever, First off the clothes never came out clean, regardless of how diligent I was following the directions on how to use this particular type of machine. Secondly, it started going off balance for every load if I put more than 4 pieces of clothing in. 2 months after having it recently repaired AGAIN for not spinning and going off balance, it is doing it again. It is only 4 years old! I bought it for the Maytag reputation, but now I am doubting that reliability.