At 36 months old, my Maytag refrigerator has already suffered from a Freon leak. After repair, the leak continued causing the fridge not to produce ice. After another Freon charge 7 days later, the fridge will freeze ice only in a manual ice tray. The water in the ice maker for whatever reason will not freeze? To make matters even worse, the freezer fan has been noisy for the last year. Maytags solution is to purchase extended warranty for $300 plus or hire repair person at $100 for first hour. A 36 month old refrigerator is in essence a disposable item. Basically for a $700 fridge… that breaks down to about $20.00 per month service charge and then it’s time to replace!

I am writing to tell you the dishwasher sold to my family malfunctioned as a result of an apparent design flaw. I also ended up wasting an entire day for a service person who never arrived. On October 14, 2009, my family bought a Maytag Dishwasher (model #MDBH979AWW) from Home Depot. It had run beautifully until last week, when the left-hand side of the control panel went dead. I then called the Maytag service number (800-688-9900) listed in the instruction manual and scheduled an appointment with the A&E Factory Service vendor for the following Friday (July 6th, 2012) between 8:00AM and 12:00PM. Around 12:30PM, no one had arrived, so I called again. I was told by the agent that the technician was en route and would arrive at my home in forty five minutes. At 2PM, still nobody arrived. I rang again when I was then informed that my name had been strangely kicked out of the system and made available for a reschedule. Wanting to stick with a Maytag-approved business, I went ahead and scheduled the next earliest appointment available, Monday, July 9, 2012. The technician from A&E Factory Service that actually did show up reported that the entire control panel had to be replaced at a cost of $281.48. Interestingly, he added that he had seen other Maytag dishwashers with this exact same problem and recommended that I wait until the water settled before adding extra dishes during a cycle since water apparently leaks into the electronics via a small gap on the top of the inside of the door. Of course, there is nothing in the instructions warning against such.I chose to fix the machine since I didnt have the money to purchase a new one. Are your dishwashers designed to last only a few years? I truly believe that I have been duped by Maytag since this problem resulted from a design flaw. I am asking you to please look into these matters and correct any wrongdoing that you see fit. Copies of receipts for the dishwasher purchase and service repair are enclosed.

When my husband surprised me with a double oven stove I was leery. First Thanksgiving my thoughts were concurred as the 20lb turkey fell from the chinsey rack.....even a cookie tray with almonds fell down.... Unfortunately the lower oven is off by 1/2, no racks work in there. My biggest gripe is that the seller did not exchange it, just tried more racks. Now Maytag will not do anything but allow me to order more racks. This item is a huge piece of junk.

Dryer needed to be serviced within 2 months. Drum seal fell out. Service was no questions asked. Fixed promptly. Washer works fabulous. Gets clothes clean. Surprisingly quiet. You do need to keep up to the sensors on the dryer. Must be wiped with rubbing alcohol to keep performance.

Bravos X high efficiency... efficient at not cleaning your clothes, efficient at ruining clothes, sheets, towels, may be efficient at being a boat anchor. Maytag offers nothing. Have had washers last 20 years or more. Someone, or some atty. General should bring a class action suit. Horrible product. Dont buy one. DONT BUY MAYTAG/WHIRLPOOL. THEY DONT TAKE CARE OF THEIR CUSTOMERS. JUNK. That report was very fair as requested. You really dont want to know how I really feel.

We bought a Maytag Gemini double oven in June 2007. It has been a problem from day one. It arrived with a damaged door. They reordered and replaced it. Through the next few months, I became very discouraged with the oven. I bake a good bit and was always used to an oven with fairly accurate temperature. This oven will not reach or sometimes just wont maintain a steady temperature. After a couple of service calls, I gave up. I now raise the temperature setting about 50-75 degrees higher that the recipe requires. Naturally, I dont always get the best results. However, that isnt the thing that really bothers me. These ovens have three ignitors. About every six months, one breaks. The cost is over $200.00 each time. The ovens/broiler are highly unreliable. After mixing up something or on an important holiday, one may find that the oven wont light. Theres no warning! It is simply gone. I will never again buy a Maytag! I called Maytag and questioned them about the lemon law. I was told that the same piece had to break three times in one year. That is crazy, when the entire thing doesnt and has never worked well.

When our ice maker (Model # MF12269VEM10) stopped working, we contacted Maytag, only to be told that the 1-year warranty had expired. So we had no recourse but to contract a repairman. He replaced the valve (and in the process, because of Maytags decision to use plastic tabs instead of screws, the tabs for the filter housing broke off in his attempt to reach the rear of refrigerator where the valve went and we had to pay to have the housing replaced, also). The new valve did NOT fix the problem. Water continued to run out of the water dispenser after you removed your glass. We re-contacted the repairman who returned and proclaimed that there was air in the lines and it should work itself out over the next several days. Yet that night, I noticed drops of water running down the control center and filling the drip tray. I placed a towel on the floor and emptied the drip tray several times that night, before turning off the ice maker completely the next day.Unhappy with the original repairman, we contacted another who came out and discovered that the new valve was leaking from the top. That is when the filter housing broke and we had to use duct tape to hold it in place while the new repairman ordered a replacement. He tightened the valve and cycled the ice maker several times only to discover that the water overflow switch on the ice maker wasnt working, thus water was overflowing into the ice maker container. He turned down the water pressure to the refrigerator, and we tested it again. All seemed to be well until the next day when no ice was released from the ice dispenser. When I removed the ice storage bin, I found everything frozen from water overflow. I turned off the ice maker entirely and contacted the repairman, who ordered a new ice maker, which took about a week.After the new ice maker was installed, along with the new filter housing, the repairman cycled the unit several times before leaving. Yet by the next day, the ice in the storage bin was frozen in place again (I have pictures), and we contacted the repairman who ordered yet another ice maker. It took yet another week for the part to come in. After it was replaced, I monitored the ice container each time I heard ice drop into it. The 1st time there were a few drops of water in the bottom of the ice maker. The 2nd time, there was a 1/4 cup of water in the bottom. I immediately contacted the repairman to let him know and turned off the ice maker yet again.I find it hard to believe that a new valve, fresh from the package, and 2 (TWO) ice makers, fresh from the box, were all faulty. The repairs started on February 25th 2015. It is now March 21st and the ice maker is still not repaired. The 2nd repairman is doing his own research into the problem (for which we applaud him!) and now we ask you for your feedback as to the problem and how it can be solved.

The serial number is MDB8979SBWD. Just a few months before warranty expired the buttons were being flaky. Eventually it would not start. We brought it to the dealer because they wanted $150 to come to the house. They replaced the front panel. It lasted less than a year and stopped working again. Being out of warranty and being a technician I took off the panel and saw that there was no insulation in so the humidity would build up. The wires in the ribbon wire were corroded. I looked up the price of the panel and it was $150. The dealer wanted $150. I did not want to replace it because of the possibility that was not the only problem. We paid $400 for it on sale, (a mistake I know better than to buy stuff on close outs.) FYI to get the dealer to deal with it it would cost $300! From reading these complaints this panel seems to be a real problem with this and Maytag is not supporting this LEMON. I see a lawsuit here. Too bad Maytag is only out for profit. What is disappointing is that Maytag is owned by Whirlpool. Whirlpool has or used to have good appliances. We had a microwave that lasted 15 years and our last dishwasher that lasted 15 years. We will never buy Maytag or Whirlpool again. Maytag is junk. The dishwasher is probably ok except for the panel. Shame to get rid of it for that but unless I can bypass it that is what we will have to do. $150 is too much for a gamble and it seems that panel is a problem so it probably would not last long anyway.

Had a brand new Maytag MDB4949 dishwasher installed on 10/20/15. Noticed an acrid smell of burning plastic coming from the pull handle. After going to the reviews I see a pattern of shorting control panel boards melting the ribbon cable. Having repaired Xerox copy machines for 17 years, I recognized the smell of an electronics short and melting plastic. There are 600+ complaints for the same thing. Going to call the store we purchased it from and will escalate from there.

Bravos MCT - I researched online and bought the highest rated machine that had the features I wanted. I like the top loading and the less water used. It cleans well but I would like more control like water temperature for example. I have had this washer about a year. I also want quiet but did not get it in this washer. That is tough cause you dont know until you have it! I think that it is hard to buy big appliances and be happy with them at my age because at 70 years old you remember when a washing machine was built to last a lifetime! Now they last maybe five years and they cost as much or more! I am not interested in lots of the bells and whistles. I just want a washer that will last and does its job. Mine has a glass door in the top so you can watch your wash (I guess..). Well, who wants to stand around and watch your wash...get a life!!! Also, it fogs up right away so you couldnt see it if you wanted to. It all seems pretty silly to me but I guess that is the way the world works today. So I go with it and I watch my wash.

We bought all new appliances for our remodel. I wish I could return this dishwasher. It has a problem with the door staying closed. I added images of how we are able to make it work. A service person is coming by tomorrow to put a new latch on it (I read several reviews saying the latch is messed up). So I made sure the service person is coming with the part. I called Home Depot when the problem started (used for up to 5 washes or so). And Home Depot wont return it! I called Maytag and they tried selling me an extended warranty and I asked what about the 10 year warranty the machine is supposed to come with? I guess thats a joke as the lady told me I should of read the fine print. So buyers beware! I wish I would of know about Maytag. I would have about a Samsung instead!!!

I purchased a Maytag dryer #MEDB400VQ for $715.48 along with a 5-year warranty for $119.99 on March 30/2012. Since then, the dryer has broken six times. Our warranty stated that after it breaks 3 times, we would get a new dryer. All claims for a new dryer have been denied. The dryer is still broken, going on 10 days, only to find out that parts needed are on back order for two more weeks. This is unacceptable! I will never ever buy a Maytag again and will tell all family and friends my story so they do not purchase a Maytag and go through the hell that Maytag has put my family of five through!

Purchased a Maytag Bravos XL less than 3 years ago Model MVWB725BW0. We have had several repair calls. From reading complaints from others, I have the same: clothes balloon, clothes rip, dark clothes have a scum on them, even a blanket goes off balance and it is hard to start the cycle. It goes off balance all the time, makes a squeaky sound when agitating and the housekeeper can never figure out what cycle to run the clothes on because they always go off balance, there is a loud vibration, etc. The last repair call was for an actual leak on the floor! The appliance company charged us $95 for the service call, did nothing, and told us the parts would be more expensive than a new washing machine. Went to Home Depot today and purchased an LG washer and dryer for over $1500. I am not even going to try to recoup anything from Maytag because this is the second Maytag that I have had a bad experience with and didnt learn a lesson in the first place. Junk. :(

We bought a new Maytag fridge in 2013, french doors, ice maker on the bottom. In 2 years we have replaced the control panel on the front door 3 times. Each time the plastic panel cracks and breaks free. The last time they replaced the entire door, all on warranty. Well 3 months later it does the exact same thing. I call Maytag and they say, fridge is past its warranty period so no coverage. It will cost me about $600 to replace this control panel.

Maytag Dishwasher Model # MDB7809AWB2. Part = Console Keypad. We have lived in this home for approximately 4 1/2 years. We purchased a Maytag Dishwasher and had to replace the motherboard in it about 2 months after the warranty ran out. We paid 1/4 of the cost of the dishwasher to get it fixed and I am having the same problem again. I am very dissatisfied with the appliance and I will not pay another $200 to get it fixed. I will never buy another Maytag appliance. Dont buy Maytag!!!

Most American dishwashers are made by Whirlpool. My control panel failed after only 3 years (design is terrible!). I had to pay almost 50% of original dishwasher cost to have it replaced by Factory Service Co. (formerly Whirlpool service).

This Bravos washer and dryer saves energy for sure, but sadly, that is it. It does not wash my clothes and rinse them adequately. They are so twisted and wrinkled I have ironed just about all my clothes. Even my synthetics are severely wrinkled. The dryer sensors do not work. They never dry the clothes adequately. The concept was good in that they are compact and have a large capacity, but the design does not work. I was lured in and unfortunately, there were no reviews at the time but I see that everyone shares my sentiments. The washer and dryer are just not any good. Thank you.

An average refrigerator/freezer at best. I would not recommend it unless you also buy a service agreement to fix things that go wrong with it. Ice maker went out.

This happens to be a commercial one - I dont know why; the landlord bought it. It will not do just 1 or 2 items. I would need this for when I have a very muddy towel from the dog & dont want to put anything else in with it; or with a newly purchased item that I want to wash by itself. It gets stuck on the wash cycle & will not continue. Then I have an item(s) that is soaking wet, which I dont want to put into the dryer. And in the winter, I cant put it outside. I did an online chat about this & was told not to just put one or 2 items in the washer. What??? Im 68 years old; have been doing wash for well over 50 years & have NEVER had this problem. I dont know if this applies to all Maytags since this is the only one Ive ever had, but I would definitely not recommend this product!!!

Gave up a very good old washing machine to update to a newer one and so we got the Maytag bravos 300. I thought Maytag was a very dependable name and product. The warranty went out. 2 weeks later, the water pump went out. I had to pay to have it replaced. Then after that it started making noise that got louder and louder and now it sounds like a thrashing machine. And now it has started leaking water out of the bottom. So its going in the scrap pile. What a loss of money - the worst investment I have made. For what I paid for this machine, it should have lasted for many years to come. The washer I had before this Maytag I had for 16 years - no problems at and it still worked great when I gave it away. Maytag use to be a brand you could count on. Great craftsmanship has been taken away and monetary gain has taken over. I hope no one else has to go through this nightmare that I have. Maytag they should have to give peoples money back that we all worked hard for. Going with a LG now, hope its a good machine.

Washer model mvwc200bw1 c43942055 -Worst washing machine ever! The clothes come out all twisted together, I cant even see how the washer works because the lid locks when washing! The sound the washer makes while washing sounds like its barely even washing the clothes! I will never purchase any Maytag products and I wish I could return this one!! So disappointed, Im sticking with Whirlpool!! Plus the clothes dont even get that clean!!

I purchased an LG (white) washer last year, but my husband upgraded all appliances to stainless, including Maytag washer and dryer. The washer does not fill with enough water to cover the clothes. It barely agitates them to wash. Some clothes even come out with dry spots on them at times! They smell and are still dirty when done. I have tried every setting hoping that was the issue. Normal, power wash, none work any better! Had to resort to the soak function which does not add fabric softener or drain the water completely. Thankfully I didnt sell or get rid of the LG. Putting the LG back in asap. Nevermind the mixed color finishes of white and stainless between the washer and dryer. Clean clothes most important! Piece of garbage and complete rip off!

I purchased a Maytag Washer and Dryer about 3 years ago, they were under warranty for two years. Two years and 10 later the dryer breaks down, repair 310.00, two months later the washer breaks down again, 331.00, while I’m waiting for repair appointment the dryer breaks down, 130.00. Then I’m finally able to do laundry, turn on the washer for the first time since paying 331.00 and IT DOESNT WORK AGAIN, another SEVICE CALL!!! $$$ IM EXTREMELY DISAPPOINTED IN MAYTAG, ESPECIALLY AFTER VIEWING YOUR COMMERCIALS!!!

I have always used Maytag products at home and work. I have never had a problem like this one. The front load washers have a manufacture default with the boot that allows mold to grow even when it is wiped out as instructed. I have contacted other people and they have the same problem. I will not or ever buy a front load Maytag again and could never recommend this product to anyone. I feel that the Maytag company should replace the boot with a different design; at no cost to the consumer! This machine was only a year old. I have no problem with the company I bought it from. They replaced the boot with a bill of $358.65.

Please let me know if there is a class action suit. This refrigerator leaks water all my floor every three days or so. I have to chip the ice off the bottom of freezer every three or four days. Storage is also a joke. Poor design.

Maytag junk MFW2055FRZ00. We had to replace our reliable 15 year old Frigidaire side by side fridge when it failed due to a compressor failure. We should have pressed the service company to replace it or found someone who would. We were limited in replacement units because of built in cabinets, thus a smaller French door (so we have to open two doors rather than one) Maytag. Perhaps our 30 year old Maytag washer and dryer made us believe Maytag still offers high quality products. We were wrong. Everything about the unit is poorly designed, cheap and flimsy. The freezer drawer pulls out unevenly and the ice maker is primitive. Above all no matter what appliance you choose be sure there exist factory authorized servicers in your area otherwise warranty issues are a problem.

We purchased a high end Maytag Dishwasher from Lowes just 2 years ago. Within a year the machine was turning itself on, beeping for no reason, and eventually the functions on the control panel stopped working. When I called Lowes they gave me a number for a repairman who informed me that the cost of a new control panel would be $514 and its a known issue with moisture getting into the control panel. This is unacceptable. There are hundreds of complaints and a class action lawsuit regarding this issue and yet Maytag has done nothing to remedy this situation. I am forced to purchase a new dishwasher and I will never purchase another Maytag product.

How can any company with a reputation that we all have grown up with MAYTAG pull such a DESPICABLE act on its customers of 20, 30, 40 plus years ??? $500+ repairs for each of 2 boards in nothing better than a BOAT ANCHOR... I would give anything to have my 15 yr or even 20+ yr old pair back! Worst purchase of our 50 years of life! Its overdue time for a Class Action Lawsuit! Also has no one had your washer jump and dent your dryer? Imagine a child in a room with something as Vicious as MAYTAG BRAVOS! Just as well have them play in the STREET! Lets all join together and show MAYTAG the consumer does count. Thank you...

I purchased a Maytag Bravos 5 months ago. I had trouble at first with unbalanced loads. The repair man came to look at it twice. One thing that can unbalance your loads is if small pieces of laundry such as a sock gets outside the basket. Sometimes the basket has to be taken all the way out because small pieces can be lodged under the basket. This happens when you fill the machine too full and those small pieces float to the top.The suspension on my machine ended up needing to be replaced. I have read lots of reviews about soap rings in the clothes. That happens from using too much soap. Make sure you are using HE detergent for one. I cut way back on my soap and my laundry gets clean and no problems with residual soap on my clothes. I was very unhappy with my machine at first but now I absolutely love it!

Add me to the long list of disgruntled buyers of a Maytag Dishwasher. Just like the other 488 people that similarly filed an unsatisfactory rating on this site I too am now on that list. And no surprise - the control panel ceased to function 13 months after I purchased the unit and one month after the manufacturers warranty expired. After brief inspection the problem was obviously a design error leading to premature wear of the electric ribbon in the handle. Phoned Maytag and they advised me it was the first theyd heard of this problem with the model. Only subsequently did I search to discover that the problem was so common it might be characterised as routine. Replace part was 8 weeks and Cdn $153, about 2x the US price. However they wouldnt ship it to me from the US. The repair isnt too difficult: 11 screws and a little patience if youre so inclined. Before installing take a few minutes to trim the plastic where the electronic ribbon strip passes from through the handle without clearance. Save yourself the same repair in another 13 months. Lesson learned - no more Maytag/Whirlpool dishwashers for us.

Washer has plenty of functions for me to was even my work clothes. These saves me money and time. Washer leaves clothes clean and you can even wash your blankets.

I bought a new Maytag dishwasher 9 months ago from Costco - Maytag 24 in. Built-in Dishwasher with PowerBlast Cycle, White. This dishwasher needs a new motor - Please do not buy this dishwasher. It is garbage.

We bought a Bravos model in May 2010. Two years later, the machine started making noise during the final spin cycle. We finally called a repairman who came today and informed us it was a bearing in the outer drum. The cost for the part (the drum assembly) was $290, not to mention the cost for labor. Since we only got the original warranty, the service center at Maytag refused to help with the repair. We, as others who have had problems with Maytag, bought the washer because of Maytags reputation. This is why we have to buy extended service warranties. Companies make trash! What happened to the days when an appliance lasted longer than 10 years? Why cant we buy a good sturdy appliance without superficial bells and whistles? We have no idea if any other brand is better, but we will not buy another Maytag.

We purchased a Neptune washer/dryer combination with pedestals a few years ago. The washer vibrates so violently that I had to block it between the dryer and wall to keep it from walking across the floor during the spin cycle. We had a technician come out, and he stated that the unit just needed to be balanced. The level I used showed the washer balanced in all 4 directions. Then he said I had to balance it with the machine running to stop the vibration. That didnt work either. I had previously installed vibration dampers and the technician told me that makes the vibration worse. When is someone going to file another class action lawsuit against Maytag, as there appears to be thousands of complaints for this same washer?

I have had my washer and dryer for more than 5 years. As normal, over time, stuff wears out and parts need to be replaced. The manual doesnt list part numbers that are needed. The website doesnt pull up part numbers when you type in the model number. After paying for overnight shipping that isnt guaranteed (and was more than the part itself), it didnt show up until a couple of days later and it was the wrong part. I would have to pay for shipping costs of the return, now tripling the cost of the actual part. Calls to customer service were not at all helpful as all they could say was that I would have to pay for the return shipping and they were sorry there was nothing they could do. I wont be purchasing anything from Maytag ever again.

Model# MVWB850WQ0, Serial# CY4070329, Type 580-02. Bought this Commercial Technology washer 2-1/2 years ago thinking the commercial model would be heavy duty. It was only heavy on the wallet. The washer started to emit a loud roaring sound two weeks ago that never happened before. It happens on spin cycle. We cant even have a normal conversation in the house. After reading similar problems and outrageous cost to repair, Im leaning to look for a replacement without the Maytag label. My 10+ year old Sears Kenmore didnt have any problems. My mistake was to replace it with a more efficient washer. I guess New+Efficient doesnt equal long lasting for Maytag. You would think a major manufacturer would put in heavy duty bearings in a washing machine. Heck, maybe the bearings are heavy duty but design shortens bearing life. Enough time spent on Maytag. Stay away!

It meets all of my needs and expectations. Its quiet looks nice and does a very good job of cleaning dishes.

Bought new Maytag French Door with cooling drawer refrigerator in July, & have had nothing but problems with both product & customer service since. Have already had 2 service calls for the SAME problem. The in-door ice maker/dispenser is a horrendous mess. Place a container below the opening to get ice cubes & ice is sprayed in chunks all over the floor & around the kitchen. To get ice, you have to put the container in direct contact with the opening, & then place a towel over the entire in-door unit to keep ice chunks from spraying all over the floor. The unit has a small flap-door in the ice maker, which must open & close automatically when getting ice, but the flap failed to close, so the ice in the ice maker was melting & the water running into the refrigerator unit & onto the floor. Called warranty repair & they came out & said they fixed the door-flap, but they did not. Ice was still melting & the freezer unit would not even keep ice cream & pastry items frozen solid. Called repair a 2nd time during the first 4 months of ownership, & they came out & replaced the motor to the small door-flap in the in-door ice/water unit. When asked why the freezer would not keep ice cream & pastry items frozen solid, the repairman stated (quote): Freezers dont keep ice cream frozen solid because it has so much sugar in it, its like alcohol. Had no excuse about the pastry issue however. We replaced a 12-year-old Jenn-Air with this piece of junk, but at least the Jenn-Air kept ice & ice cream frozen solid, & the ice maker did not leak & spray ice around the kitchen. Jenn-Air must know something about freezing sugary ice cream, that Maytag/Whirlpool do not understand. Then today we got a notice that Whirlpool had denied payment for the 1st repair visit, even though the unit was only 2 months old then. As such, we expect them to deny payment for this 2nd visit, even though the unit is now only 4 months old. Bad product & sloppy customer service, from a company with ZERO consumer support.

We purchased a washer and dryer, spent in the neighborhood of 1000.00 hard earned $$... extended warranty, the whole enchilada. Maytag. dependable, lonely repair man, ha.. that is just so much stuff. Well anyway it was a Centennial set. What junk. Never really worked that well to begin with. I trashed them both after exhausting all avenues to make it right. Well I got the hair to report the mess to consumer affairs and see if they are what they claim to be. This is more of a warning to all consumers.The stuff you consume today isnt worth the money you pay for it. The money isnt worth the time you spent to earn it. I am gonna try to find a old washer and rebuild it, and a dryer as well. Or just use solar. Best to keep the old stuff repaired and running. I dont know how many people I have spoken to about this problem. Our infrastructure is crumbling. A consumer based economy. Only there is not anyone to service the products we consume... pitiful. I guess my wife will be out back with a tub and washboard before it is all said and done... she will not like it, I guarantee that. I could not even begin to repair the washer. It was a computer operated board that did not work correctly from the beginning. The dude came out from the repair shop and fixed it while still under warranty. It died a slow painful death shortly after that. I disassembled it with a screwdriver and now have potatoes growing in the tub.The dryer has not met the same fate yet. It just sits there, anticipating the moment when I remove it and dissect it with a Sawzall. And I guarantee that day is coming. Do not buy anything from Maytag or its subsidiaries, think long term. We have become a bic lighter economy. I have been on the forefront of that movement. I did not realize it at the time. I do now. and for that I am sorry. I always expect something to work when I need it and if it doesnt, I try to repair it. Cannot fix this stuff now. The support we used to take for granted has been outsourced as well as the production of the product. Bob Dylan said it best in the song union sundown... Thank you and e pluribus unum.

I wish I had read these reviews before purchasing my dishwasher. I have used it 40 times max. The control board went out. They want 307.00 to fix it. Really? Why would I fix this piece of crap when I can buy a cheap one for that price that would work better. Ridiculous! I paid good money for this dishwasher and the warranty that comes with this is a joke. Save your money and brand from a company that stands behind their product.

I chose Maytag because they received a good rating from Consumer Reports. I liked that they were for extra large loads however now that Ive had them for 12 years I know the large loads are no more than my old Kenmore washer and dryer. The real deal breaker for me is the size of load that you can actually wash. I was hoping I would be able to wash a blanket without worrying about the washer going off balance. My washer and dryer are Maytag although I dont know the model number. They are full size but the extra large load is not extra large. The knob on my washer broke and Maytag wanted $15 for a plastic knob! I found it on eBay for $3. The washer goes off balance too easily.

I bought this POS and paid almost 1000. Out the door with tax, hoses, delivery, etc. And it is by far the worst most useless pile of crap I have ever purchased. It just does not work!!! Its a washer that does not wash. It uses enough water to wash one sock and that still comes out stinky.. All my clothes no matter what cycle I use including deep fill power wash or if I add my own buckets full of water to the 1.5 hour wash cycle still come out dirty, stinky, stained and caked with detergent...Hey Maytag heres a hint. You need water to wash clothes and you need agitation to get out the soil, the dirt, the sweat, the stains, the stink and your washer does none of that. In fact I could get my clothes cleaner if I out them in the bath tub and swished them around with a broom stick for 3 mins. How could you go from the loneliest man on earth to the biggest scammer on earth by producing this boondoggle... P.S. Its only me and my wife. We are retired and our clothes are not even that dirty... Its just common sense. No water no action no clean. Ill never ever ever buy anything that says Maytag on it ever ever again and you can bet your life Im telling everyone I know this story.

We have had this dishwasher [Model MDB7749SBW2] for about 1 1/2 years now, and gave had a lot of trouble with it. It will run a cycle on its own without anyone even touching a button. My current problem is the start button wont work. I reset the dishwasher by pushing the series of buttons I found online to do a reset, and the start light lit up, but after the reset cycle was finished I tried to run a wash cycle and couldnt get the start button to do anything. Ive seen a lot of reviews online on this being common with Maytag brand dishwashers this old. I will NEVER buy a Maytag product again nor would I recommend it to anyone as a good product. I am very frustrated and disappointed in Maytag!!!

Okay, on March 2009, we bought this brand new microwave due to our major remodeling. We didnt move into the unit until February 2010, so the microwave was in its box for 11 months. After we moved in our condo, my husband and I had to travel for work for almost a year so our brand new microwave is very slightly, gently and barely used. Well, for the past 2 months, it had been acting up. Sometimes it heats, sometime it doesnt. For a 2 year old microwave, which we paid over $400, I would assume that it would last. It no longer heats up, so I called Maytag customer service to hear her tell me its not covered under the warranty and would cost $269 for repairs and there was nothing she can do for me unless I pay for a technician to come and repair it! No way, I swear it probably got used 5-10 times a month to heat up coffee for about a year. I am sure there are some major quality issues on this model because when I googled Maytag microwave, all I see is the same magnetic problems. I spoke to a group of my lawyers friends. If youre interested in joining a class act law suit, please e-mail me. I hate that people are being taken advantage of by these terrible companies. I cant believe how low quality their customer service and products are. Believe it or not, my $30, old microwave lasted me 14 years throughout my college years until we decided to replace it with the modern stainless steel one. It got noisier in time but not broken and still heats up just fine. This $400+ one lasted me only for several uses. Shame on Maytag, when I have time, I will be sure to write a complaint to the consumer department as well. I will dedicate my life in spreading the word out about their low quality product. Don’t buy Maytag unless you only plan to use it for a year or 2.

I had bought Maytag Dishwasher MDBH979AWW3 in Sep. 2009. Oct 2011, the dishwasher stopped working and the control panel had to be replaced, few days later, it stopped working again and the Thermal fuse had to be replaced. Now two months later, it stopped working again. Till this point, Ive spent a lot of money on the repairs and I wish I had used that money to buy a new dishwasher. Looks like not just the Maytag dishwashers are faulty, but even the parts they have are faulty. I will not recommend any Maytag products to anyone.

We purchased the Bravos X washing machine on Feb. 9, 2012. I had a Maytag for 30 years before this one and did not have any problems. My model # is MVWX700X. I have given it sufficient time to get used to it. I have tried all cycles for my whites and am not satisfied. I use Clorox in the receptacle and I have only used Tide HE. I spot treat all of our underwear, which is changed every day, and it always comes out unacceptable. I am so disappointed since I was so fond of my old one and only thought I wanted another Maytag. At this point, I would never recommend this machine.

We recently purchased a Maytag refrigerator, love it, no problems until the mystery person in my house accidentally broke the slide out door for bottom drawer. So I called Maytag, and with no questions asked they sent me a new part by Purolator! Great customer service makes everything better! Thanks Maytag.

I have always hated soft touch control panels so I purchased a Maytag Dishwasher with old style push buttons. IT DID NOT CLEAN THE DISHES, so Lowes took it back and I was convinced to UPGRADE to an MDB7749SBB0 and was told this machine was top of the line, although it was VERY temperamental from the start. I guess I should have done my homework. I see now several complaints about the control panels not working. I was told that MAYTAG was a very reputable company and that they stand behind their product. WRONG!. The company KNOWS these panels have problems and should replace them free of charge as it is obviously a defect. Nope, first they offer to send someone out (In a week) to repair it at $80 just to look at it and the panel is over $100 to replace, and when I complained they tried to sell me extra coverage for $250. REALLY? What is the purpose of purchasing a QUALITY dishwasher? I might as well purchase a cheap dishwasher and replace it when it breaks. I think you should be responsible for your product when you have several complaints on a specific part.

I totally understand the technology age. We need to move forward as a country and keep up with modern technology. But somebody please tell me why this means companies have the right to not stand by their products? Why do consumers have to pay the price for bad products and companies leaving us high & dry? My husband & I were excited to redo our kitchen. We bought all new appliances in November 2011 - all Maytag. In December 2012 (13 months after we bought them), we started having issues with the oven. The oven would not maintain the proper temperature. We called a service man in January 2013. He deduced it was the computer board so he replaced it. Cost to us - $350 (including service call and labor). Now, less than 2 months later, the same problem. Maytag, Whirlpool, Kenmore - whatever company you are now - rest assured, you will not survive if you continue to produce shoddy products and refuse to back them up. The service man is to stop by again tomorrow. I refuse to keep plugging money into a product only 15 months old. I will not buy another product from you again. I just hope the dishwasher, microwave and fridge make it to at least 5 years old. Isnt this funny? My grandma has a Maytag washer & dryer - 35 years old. You sure cant say positive things about your products today. Good luck to your future - youll need it.

Purchased a new Maytag dishwasher three years ago. After having it for one year the panel box no longer worked. Had to pay $300.00 to repair. Now half way through washing the dishes again no water will go into the machine. Only the first part of the cycle. I am sure it is going to be the panel box after reading other peoples problems with this machine. I will not pay to have it fixed this time. I will have to buy a new dishwasher. I will never purchase a Maytag product ever again. I have lived in my home for 40 years and never had a problem with any appliances. This would have been my third dishwasher in 40 years and as you can see it has not even lasted 4 years. I will inform my friends to stay away from Maytag.

2011 model MVWC2oox W1- spin dry failure - We purchased above top loader in 2011 and have had no issues until now. Currently constant failures on spinning and drying. Spin cycle stops without getting up to speed and appears to be an unbalanced load sensor problem. Also draining is not completed (possible pump going bad). Area tech came out within a week as promise and ran the diagnostics and found no faults. Problem has continued. We do a load a week. Looking for better answers or a new washer.

Bought a Bravos, large capacity, top load washing machine few years ago. (Purchased at a Lowes.) Been nothing, but one problem after the other!! I hate it! NO MORE MAYTAGS FOR ME. Has required several repairs of various parts. Now again, after being repaired few months ago, something else has gone wrong. Would have been cheaper to replace a 3-4 year old machine than keep having repairs.

Leaking water and puddles in front (each side) of refrigerator. Purchased from Home Depot on 12-20-2011... After doing a search on the internet I found that this is a common problem with the Maytag refrigerator. This model is a two door with ice maker on left door and freezer on bottom of unit. Looks like Maytag does not want to be bothered with my problem. Model #MF12569YEW. It certainly was not an inexpensive model. Whatever happened to the Maytag repairman who was never needed because the Maytag products were so great???Updated on 03/21/2015This is not the first time this Maytag product had problems. Expensive piece of junk in my book! First, as many consumers have experienced there was water leaking in front of the refrigerator onto our hardwood floor. Now the door gasket seal ripped on the end tabs. What happened to Maytag?

I purchased a Maytag Bravos line washer model # mvwx500xwo back in Oct. of 2010 thinking that it would be great to save money on the water bill. I first had issues with it putting holes in my clothes. I then found out if you do not zip up all zippers and button all buttons, the machine will rip them up due to the high speed spin cycles. Now, the washer will not fill with water or start the wash cycle. I mean really, its less than two years old and I have to shell two hundred plus dollars to fix a washer that only cost $500. I guess I know what brand not to shop for next.

I love my Maytag washing machine. It have different settings for the wash, also a size load for your washing, and I love the rain cycle. You could do single runs with Downy or extra runs which is great. Especially great if you’re doing blankets and towels you need that extra rains. Great reliable machine. Highly recommended.

Purchased this unit back in November 2011. Sometime this year it started leaking water just like many others from the freezer unit onto the floor (many times large puddles). Im tired of the permanent towel on the floor to absorb the water to prevent a potential slipping hazard. I too went online and found a very nice video on youtube which showed how to disassemble the freezer compartment. Took everything apart and noticed that there was water frozen on the supply line. Melted this and put everything back together, for about a week there was no water leaking so I figured all was well. About a week later the puddle was back so I sent an inquiry to Maytag and let them know I had an image of the issue and asked if it was covered through manufacture warranty. Here is their response: Your email is extremely important to us here at the Customer experience Center and we sincerely apologize for any delays in responding to your email. We are working diligently to respond over the telephone and through email to all of our customers. We are sorry to learn of the problem you are experiencing with water leaking from the bottom of the freezer. Unfortunately, we are unable to determine from this location the exact cause of the problem. We recommend that you contact a certified technician for an accurate diagnosis. Once the problem has been diagnosed, please contact us back so that we can review the concern further to determine if assistance is available. For your convenience, we have provided below service providers in your area that you may contact for service. Aries Appliance Service (925)367-7708, Vigil Appliance Service (925)371-7701. You are a valued customer and we do apologize for any inconvenience this concern has caused. We invite you to contact Maytag again either by calling (800) 344-1274 between 8:00am to 8:00pm EST weekdays or by emailing whenever the need arises. When calling please press the available option or stay on the line to reach a representative.Frustrated I went online and found this forum where hundreds of other people had the same issue and that many of them were resolved by the new P Trap. So I watched another video by the same guy on youtube that showed how to replace the P Trap. I went online and found the replacement P Trap Manufacturer model # w10619951. One of the comments there actually said to call Maytag first as they were able to get a replacement P Trap for free. I believe if it was under a year old they would also pay for the labor to have it replaced. So this morning I called Maytag, the first guy Jim said I would have to have a certified Tech come out (76 dollar service fee, plus whatever the labor would cost) and Maytag would cover the cost of the part. I asked Jim if he could just send me the part and Ill do it myself, he reassured me that he could NOT do this and that the system was very specific. I told him I did not understand that a bad design and known quality defect, why should I have to pay several hundred dollars to fix? He told me that was the way it is. I asked to speak to his supervisor and put me on hold. Not only was the hold music extremely obnoxious but there was a loud humming noise as well, I waited for 10 minutes hung up and called back. I spoke with Maggie this time. I told her I wanted the part sent to me and if she couldnt help me I wanted to speak to a manager. She said she did not have the authority to ship me the part without approval. She said she could ask for approval and after waiting for about 3 minutes she came back on the line and said she spoke with her supervisor and that they would be sending me the replacement P trap today via FedEx. Had they not sent me the part my next stop was going to be the better business bureau..

I have enjoyed my microwave and it has lasted 10 years so far. The only problem I have had is the handle coming off but I clip it back on. Also I changed the bulb. The microwave is over the stove and matched the rest of my appliances. Basically, I would recommend Maytag for any appliances that a person would need to buy.

Purchased a Maytag Bravo. One of the worse purchases weve ever made. First the much of the clothes does not get submerged. 2nd the clothes comes out extremely wrinkled. Called the Maytag people and they explained that Im putting too much clothing in the washer. I explained Im only filling the washer half way. They explained it should be filled only a quarter of the way. What??? Do not purchase this machine.

After owning Maytag Model MHWE450WW01 for nine months, we had to have the bearing and drum replaced. It was down two weeks, and I missed two half days of work. Two weeks after being supposedly fixed, it is down again, belt out this time and I will be missing two half days of work again.After missing two days of work, I still have a piece of junk washing machine.

We have a similar problem to the others who gave reviews on their still NEW Maytag refrigerators. Ours isnt even four years old and several weeks ago we started smelling a chemical odor which then permeated all of our food in the refrigerator and freezer. We didnt buy the extended warranty because we have owned a few refrigerators and all have lasted just fine for 15+ years with no problems. So I called Maytag. They said for a charge of $369.95 they would schedule a repair and would cover the service call, parts and repair and provide an 12 month warranty. If the service call results in an inability to repair the refrigerator, they will refund the full amount of $369.95. So I asked if Maytag would then replace the refrigerator, and the rep said we have to start with the service call before they would discuss any type of refund or replacement. Im angry and disappointed in Maytag. Its a good thing we have a spare refrigerator in our basement. What a hassle! Weve already had to throw away over $100 in food that picked up that horrible odor. Shame on Maytag!

I purchased a Maytag Bravos washer and dryer combo 2.5 years ago. Six months in, I noticed that the washer would always stop halfway through the cycle. We had a repairman come out because it was under warranty and he said it just had to be reset. I then started to become weary of the product. The washer, that is larger than most, is still a problem today. The dryer, the last couple of months, has not dried clothes completely. Today the dryer just stopped. Maytag will rip you off when called for service because the warranty is expired. I have owned old dryers for several years and I am so disappointed with the Maytag product that I will make sure that anyone I know thinking about purchasing a Maytag will buy another brand. The worst washer and dryer I have ever owned.

Maytag is the brand I had for 18 years and never had a problem with the washer or dryer in all that time. So when my dryer died I decided to get a new set of Maytag washer and dryer. I picked the set together and they dont have a lot of bells and whistles, simple to use and the washer is an HE. Cost was about $900 for the pair. I bought the washer and dryer in May of 2015. Models are simple to use. I have not had any problems and quite pleased with the work they do.I like to stick with a brand if it has served me well. Energy costs need to be low and I look for sales. Capacity is something I do not need a lot of, since it is just two I am washing for. Good quality is what I look for. I have not ever had paint chipping or rusting. Never had socks missing or a bad result with cleaning or drying. The washer has a cleaning cycle and the dryer is very easy to clean, the lint filter, and I get great results with no static when I take clothes out of the dryer.

Maytag gas range model #MGR8670XS 1 - I would not recommend this range. We bought it new and when I used the self clean oven, it did not work. It took four months to get this resolved. I self cleaned again, and I had to clean the oven by hand. It did not clean very well at all. I wish I had my old oven back.

This is a continuing aggravation! On July 27, I discovered the dishwasher (MDB7600AWW) tub had developed a crack in the bottom right rear and had warped my countertop and the floor under it was full of water! I called the appliance store where it was purchased and was told to call Maytag. I have a 20-year warranty on the tub with free replacement of the unit if it fails. I called Maytag and was told we needed a service call to verify. I scheduled it for July 30, and 3 minutes and $75 later, yup, tub is cracked. Its a known problem, and the dealer has already replaced some for customers. I called Maytag to get the ball rolling for replacement. I spoke with Jennifer and was told shed get back to me.Meanwhile, we went to several stores, checking out other Maytag models. So, Id have some idea of what was available as a replacement. I called Jennifer on July 31 with a suggested model Id find as a suitable replacement. She said shed check and get back to me. On August 13, I called Jennifer for some answers, got the voicemail, and left a message. On August 14, I went online to chat. Finally, I was told Id have a replacement in 10-12 days. Id be contacted to schedule installation. On August 16, I called a local dealer again. He cant understand the problem. Hed replaced two others in a few days. He made some calls for us and gave us the name and phone for the company replacing the dishwasher as well as the work order. Installation was tentative for August 23. (Hed been cut out completely!)I called Optimus Solutions, and theyre awaiting shipment. Tentative installation was on August 23. On August 22, theres still no word. I called Maytag customer service. Sorry, it was shipped to the wrong address, so it was shipped back! Its now in transit and supposed to be delivered to Optimus Solutions today but not being scheduled for installation until August 31!This has become one nightmare after another with everyone pointing the finger at the next guy. Phone calls get only the same runaround. No, speaking to a supervisor wont help - theyll tell me the same thing. Isnt that convenient! Meanwhile, Im still washing dishes by hand and having psoriasis on my hands, which are like two pieces of raw meat right now. It is beyond aggravation; its bordering on torture! (No, I cant wear gloves. They make my hands sweat and even more sore!) Besides, I shouldnt be washing dishes by hand. I paid for a dishwasher that failed through no fault of my own, and now, Im being punished for purchasing it. I can guarantee that if I had no warranty and had to replace this dishwasher, it would have been replaced immediately!Never again. I purchased all Maytag products for my new home. As they fail, I can guarantee I will not be replacing them with Maytag or Whirlpool, which now owns Maytag. I will be telling everyone who will listen to stay away from Whirlpool and Maytag, because their customer service sucks big time.

MDB4949SDM1 - After owning Maytag model MDB/C-2 for thirteen (13) plus years, I decided to purchase the subject Maytag Model when my 13 year old died. Big mistake. Previous model was very simplistic in rack design and it provided user-friendly options such as two detachable baskets for silverware and a special rack for delicate items.The new model has been designed so your dishes go in on angles on the top rack and as such bowls, small plates etc never stay in place once you move the rack and the lower rack configuration was redesigned and the rear area which was open to allow for bigger pots and pans to fit better has been removed, so now you have to lay your pans on top of the tines, very difficult to low the dishwasher.Additionally, I purchased the stainless steel model; apparently in the coating process a drip pattern was sealed that you can see when sunlight hits dishwasher. Further the stainless steel face that they bond to the door has popped, so when you grab the handle the face pops in and out. Lastly the new design has an adjustable upper rack; I tried numerous times to adjust the rack and couldnt so when I called Customer Service for these issues, it basically boils down to if the Service Man comes out and determines my issues are cosmetic and the rack which Ive never been able to adjust should happen to work then I have to pay the service call as there is not warranty coverage. So I declined the Service Call and advised that this would be my last Maytag purchase. I highly recommend anyone considering this unit fully investigate and test out before buying.

It’s washing day today, so I’m angry, frustrated and livid to do it in my Maytag machines. I’m 72 years old and been doing this for 53 years. It’s not a job you love to do but you do it. I finally get to be able to afford whatever machines I want, so what do I do, buy Maytag. They are beautiful, see through top load, and see through dryer. So finally I get to use them, what a letdown. I don’t understand how they can put these machines on the market. Unbelievable! Also very expensive. The sensor for the water level is way off. It starts washing with hardly no water covering the clothes so this is where I put it on pause and add buckets of water to wet at least the clothing. I did a test to see how the clothes moved inside when washing. It was a load of white towels and I put in a bright green face cloth to see how it moved around in there. Well what a surprise, it stayed on top and moved about 3 inches to the right. That’s all it did. You don’t call that washing, I call that soaking! Terrible washer! I could go on and on but I’m getting too upset. Now for the dryer, the sensors don’t work right so what I do is use the timer and the temperature buttons only. Sometimes clothes gets stuck under the lint basket and by the time the buzzer tells me the load is finished drying, it is so twisted that it’s wrinkled forever. It has ruined a beautiful tablecloth of mine. I can’t sell these machines because I would feel very bad to pass them to someone else…Maytag does but not me. Because of my age I won’t be getting new machines probably, I’m stuck with them, but I would advise anyone shopping for a new washer and dryer, go out there and see what they have, come back home and look for reviews which I did not. Bad mistake! Note: I searched everywhere to write this review to Maytag on their website, none to be found!

We purchased our Maytag 4000 series washer and dryer (Model: MHWE450) in December 2010 from Best Buy. For the first six months or so, we were very happy. We started to notice that the washer was getting a little louder by the month. I checked the level multiple times to be sure that wasnt the issue. Assuming it was just part of how the washer broke in, I just let it go - a bad move! Fourteen months after I purchased the set, the washer flooded all over the floor. I opened the washer and pieces of plastic were all over our clothes. After further inspection, the drain was completely full of the same plastic. I cleaned it all up only to find that the washer tub was so loose that it was banging side to side.I called Maytag to ask for help or suggestions. They basically told me that I was out of warranty and kind of out of luck. I responded that we do a total of four to five loads of clothes per week and that there was no reason that this commercial series washer should have failed after 14 months. They offered a one-time service plus extended service contract. Feeling that I had no choice, I spent almost $400 assuming that I had a fixed washer and a year extra warranty. I was told that someone would be out to look at the washer in three days. Finally, after me pressing and pressing, someone showed up a week later. He put a list together of all of the items that were needed to repair the washer.Two days later, Maytag service calls and says that the washer will be too expensive to repair and they would be giving me a reimbursement for buying a new one. They didnt have an exact amount yet. Two more days later, they finally called me with an offer of around $550 ($250 less than what I paid) based on their research of what I should be able to find one for and directed me to the website. One big catch though - it didnt include the $125 shipping charge. When I called to request for it to be paid as well, they declined with basically a “take it or leave” type of attitude. Not knowing what to do, I called every local appliance store until I found someone that had two in stock. When I went to look at them, I was told that both of the ones that they had were rebuilt because that model Maytag washer had a major issue with the bearing and basically needed to be replaced on all of them.Luckily, I was able to buy the washer and a five-year extended service contract for around $690. So in the end, I paid $799 for the new washer, $400 for a warranty, another $100 to replace the washer, and close to $100 in laundry mat costs for three weeks. I promised everyone that I spoke to with Maytag that I would write a review to share my story and thats why I wrote this. The repair plus warranty is a joke. I like this washer/dryer but will never buy another Maytag appliance again. Next time, I will buy extended service contract from the start.

I bought a Maytag Refrigerator (Model No. MFT2672AEM10; Serial No. K31503192) on 05/13/2013 at LOWES. On 07/27/2013 my son got hospitalized due to some kind of infection. He had fever and diarrhea that didnt go away. We didnt know what caused it. When my wife was cleaning the refrigerator, she noticed that the ice bin container had a rusty screw and metal plate. Why is the ice bin screw/metal plate rusting? We informed Maytag about this issue and they replaced the ice bin. Now, the replacement ice bin is rusty again. I sent an e-mail to the Maytag Customer Service Manager on 04/20/2015 and was told that its no longer covered by the warranty. I informed the manager that this is a defective/flawed design/rusting part from the beginning and Maytag should have REDESIGNED it when I informed them first hand and not just replaced it with the same defective/flawed/rusting part. I told the manager that this is a safety concern and Maytag needs to do something about it. The Customer Service Manager I talked to didnt want to do anything about it.

I purchased a Maytag energy efficient dishwasher in June of 2010 along with an extended warranty that I keep extending. Cost $ but needed. Issue: Sensor in Panel fails so far every year and needs to be replaced. The repair technician showed me the sensor strip and indicated that this has been a big problem. (At least I have a warranty; however, it is a big pain to have to schedule a service repair person to fix the problem.) Repair (Sears) is EXCELLENT with great customer service. I did contact Maytag and there has been no recall.I own other Maytag appliances such as a washing machine and refrigerator with no issues there. In any case, I needed to replace my clothes dryer and did not select a Maytag. I purchased a GE very simple product with no sensor/bells and whistles. Not sure if I will go back to Maytag in the future - depends upon how they handle problems with their appliances. I would rather pay extra money for quality, durability, and reliability than go through the inconvenience from parts that are not made well enough to hold up.

Spent a lot of money on a Samsung washer. Will never buy that brand again. Too much money for only working for 2 years. And left clothes dirty. Had to wash clothes twice. My Maytag washer was bought with a deep water wash cycle. Totally love it. Also not a front loader.

We purchased this washer 8 months ago, and still do not have a working unit. From the very beginning of installing the new washer we had repeated F4 and E1 error codes. A technician was sent out three separate times and they replaced the ACU each time only to have the same error codes recur. This unfortunately took 5 months as each time the ACU part was on backorder. After 3 failed attempts they agreed to replace the washer with a new one. We were dumbfounded when the new unit arrived and we had the same F4 and E1 error codes! They have again replaced the ACU and still we have the same error codes! They are sending yet another ACU but we have little confidence this will work and we are at a painful 8 months with no washer.

I purchase the Maytag Bravos washer & dryer set 3 1/2 years ago brand new. I figured being a Maytag it would last for a long time but nope I was wrong??? I will never buy another Maytag product as long as I live and I will tell all my friends and family not to purchase a Maytag product also!

Purchased Maytag 3000 series washer and dryer in June 2009. Like many other reviews, the washer is making a terrible loud noise during the spin cycle. I contacted Maytag customer service and was told wait time is 10 minutes and opted for the call back option. Received a call back from an agent located in Tennessee, United States and he checked for recalls or projects and found nothing. Offered a technician call in my area for $112.00 for 30 minutes to diagnose the problem. I told him that if he checked on the reviews, he will see many regarding this problem and a bearing issue at a cost of up to $700.00. The Maytag repairman is not only lonely but out of business and Whirlpool bought them out. I would never again purchase Maytag or Whirlpool products. We are seniors and do not abuse our appliances and why do they not last at least 15 years. Talk about disposal washer machines, who can afford to purchase them every few years. The washer sounds like a jet going through our house when it is in the spin cycle.

A week after warranty expired, our 1 year old Maytag gas range (model# MGR7662WS 4) required new Direct Spark Ignitor (DSI) board. Knowing it was just beyond warranty, I inspected wiring first and found that the Bake connector on the DSI was loose, flopping around from a bad solder point on the board. Called Maytag and informed them of this manufacturers defect and all they offered was a $20 discount on a replacement part ($220 instead of $240). It worked with new part for 4 days, then something else went bad causing oven to spark, light, heat to less than 100 degrees, then shut down, then restart, then shut down, then restart, then stop doing anything. It has never worked correctly since then. How can a manufacturer of almost all domestic brands get away with such shoddy workmanship.. Taking advantage of defective or poor quality parts to sell more of the same when they fail and for an enormous markup? Where are the regulators who oversee monopolies and blatant scamming of American consumers?

In April 17, 2015, I purchased another Maytag microwave but wanted the convection oven too from Home Depot. The convection fan quit working in January 2017. I called Maytag to ask how this was covered. Maytag only has 1 year warranty on parts and labor. So basically if you dont buy an extended warranty, you are stuck with a product that quits working. Apparently, Maytags work is only good for 1 year or they would have a longer warranty. I told the Rep this when I spoke to him. He told me they normally last 5-7 years. Wow, still not acceptable. He said I had two options. Maytag could send out a repairman and it would cost almost $300. The other option was just as ridiculous. I told him I paid almost $500 to start with and it only lasted 21 months. Of course he said if I had bought extended warranty it would have helped. If I paid $500 for an oven, why should I have to pay more to cover their bad workmanship?!! I am very disappointed in the quality and price of this convection oven. The bad thing is I bought all new Maytag stainless steel appliances in 2016 to match the convection oven. The products I replaced had been in my home for 12 years with no problems.

I bought a Maytag Bravo Series 300 washer and dryer for $2,000. The dryer is fine, so far, but the washer is dead. I have not received any answers from Maytag and the product is already outside of its warranty. I only had it for two years.

Purchased refrigerator with freezer on bottom. Purchased because made in America and husband raised in IA. Have had water leakage on floor every other day. Disconnected ice maker thinking that would help. NOT. Poor workmanship. You were good, WHAT happened?

I purchased these appliances on 02-10-16 from Home Depot in Loganville Ga., for almost $2000.00. I filed the first repair call less than 3 weeks after delivery. The sensor panel was bad and had to be replaced. Now 8 months later the washer is not starting, AGAIN. The dryer will only dry one load a day or you get the AF code. This means that the dryer cannot push air over 5 or so and we need to have a vent booster fan (an additional $200.00) installed plus have an electrician run a new outlet. I returned to Home Depot with my complaint. Feeling that I have an inferior product, they tried to get Maytag to make it right. Maytag refused to offer any solutions whatsoever. Home Depot refunded a little over $300.00 for my inconvenience.The washer is an absolute ill-conceived piece of junk. It is ROUGH on clothing and does not remove soap. I started out with brand new (expensive) towels when I purchased this machine and 8 months later all of the hems have been snatched off and theyre unraveling and falling apart and are slowly becoming car wash towels.You cannot wash delicates in this machine and allow it to spin. Underwires in bras are badly misshaped or broken completely. You cannot wear them afterwards without being gouged by bent wires. The only way around this is to take away the spin cycle, but you better be ready with a clean garbage can to haul the dripping clothes elsewhere and hung up to drip dry. The washer has NEVER removed all of the soap from bed sheets. I have a dark gray set that show the soap best. Now I have to wash once with soap then wash again with no soap. This negates the machines being efficient.Unfortunately, I found the negative reviews AFTER buying the machine. My complaints are well known to Maytag, seeing has to how the same complaints are found online as far back as 8 years ago. I have been brand loyal for 30+ years to Whirlpool and thought that I was moving up with a Maytag, based on my parents 50 year experience... I was wrong! I will never purchase another Maytag product nor Whirlpool since Whirlpool now owns Maytag. I have researched and am of the opinion that Speed Queen is a far better product and plan to junk this set and replace them with Speed Queen.

Im an 78 year old man, married in 1962. In all the years and two kids we have had just three Maytag washers. To me the gold standard of quality washers. When the motor went out in our 15 year old Washing machine I considered replacing the motor, which is well within my capability. I am a journeyman industrial machine repairman formerly with Ford Motor car company before retirement.Instead, my wife and I bought a Maytag top loader high efficiency washer from Best Buy. I was skeptical when I examined the new machine with paddles instead of the agitator. Trusting that Maytag had engineered a water saving washer using paddles, I made the very poor decision to buy it. I regret not replacing the motor in my old machine. Boy was I wrong. Given the chance I would trade my new machine for the old in a heartbeat...The old machine washed everything we could throw at it. The new machine wont wash anything to my satisfaction. The bedding deep fill cycle is the only one capable of a passable job. Even then I would like a soak cycle which, in my opinion, would vastly improve results. In all I would characterize this as a total engineering failure. Why Maytag would allow this POS to be sold, where the reputation of Maytag is totally destroyed, is beyond my comprehension.

At first you think wow Maytag. Have heard was the best washer. WRONG. Clothes come out dry in spots. Not washing like it should. Whoever came up with this water saver and no agitator was crazy. Clothes dont get washed properly. Give me an old school washer to where my clothes get clean. When you have to wash clothes twice makes your power bill soar through the roof. NOT GOOD MAYTAG. NOT GOOD AT ALL.

Home Depot is selling defective appliances manufactured by Whirlpool and refuses to provide a full refund. I purchased a Maytag washer and dryer from Home Depot in August of 2010.Washer broke in February of 2011. No parts available for repair, Whirlpool replaced washer after 4 weeks. This washer broke in July 2011. No parts are available for repair until August 17th.

I purchased a product less than one year ago. The clothes are getting snagged in seam on interior of the front panel. I went back to the store and felt the same gap in the seam on the panel on a floor model, so I know it is not just my machine. I called Maytag service and a representative acknowledged the problem but also said that if there is no fix for it, I would be charged for a service call even if no part was replaced- quite a contradictory statement. She said she doubles as the Complaint Department. If this is a manufacturing defect, it should be replaced. The front panel should be recalled.

25 months ago, I bought a brand new Maytag stainless steel microwave. We had upgraded all of our appliances except the microwave when we moved in our home. Our first purchase was the Maytag refrigerator. Should have learned my lesson from that because after less than a year, the freezer on the bottom went out twice! We bought this new microwave to replace an old one that didnt match the other appliances and was worn out. Two months ago, the code SE started appearing and then would go away after a few minutes. Now it doesnt go away and you cant use the microwave. I finally called a repair person since its out of warranty and was told that it would cost over $300 to fix it. Really! Im so angry because now I have to take money. I dont have to replace a microwave that should have another few years of use. Nothing at all reliable about a Maytag. I doubt Ill buy anything else they make.

Our Maytag Atlantis dryer had smoke coming out and almost had our house on fire! Had it not for us double checking the entire house would have burnt down! The dryer is less than 10 years old and already it is tearing apart. I cant risk using it again. Terrible company. I would never buy Maytag products ever again!

I purchased a Maytag gas range about five years ago. After about two months, I noticed that the paint on the burner grates was flaking off. I called the company and they told me it was cosmetic. I have since bought two sets of replacement grates. I call the newest ones my dress grates, which I put on the stove when I am having company. I use the damaged ones for everyday cooking. Last year, the panel flashed. It locks constantly. And often, the door would not open, unless we pulled the stove away from the wall, unplugged it, and that cleared the computer. So, after months of unsuccessful door openings, the handle finally fell off completely. And the door locks whenever the oven is turned on. You have to finish your cooking, press cancel, and wait until the oven cools off, and then it will unlock. I have tried pushing aluminum foil into the latch hole on the door but have not been successful. Sometimes I just put a spoon in the door to keep it ajar while cooking. This cant be energy efficient. Of course, it is out of warranty. I saw a similar complaint about the burner grates. Also, the paint has chipped in several places on the cook top and the disks are all chipped. I am never ever going to buy a Maytag product. Oh, by the way, I called a repairman. I paid $65 for him to tell me that to replace the lock mechanism and the door handle, it would be $400. I can buy a new stove for that, but not a Maytag.

Bought new washer and dryer from Home Depot. The worst washer and dryer I ever bought. Own 11 house all have washer and dryers. Bought Maytag on brand reputation. Washer does not rinse close at all. They come out full of lint and soap. It rips sheets up. Takes like 70-90 minutes to wash and close have to be washed over cause they dont rinse out. Dryer takes (2) runs to dry. Depot said they couldnt take them back. $300 Roper washer and dryer work much better than these units I paid like $1100.00 for. Maytag reputation is **. I have Amana front loads in another house that wash in 29 minutes and they come out perfect. Amana dryer works great also. DONT BUY MAYTAG ON THEIR ** REPUTATION AND CONSUMER SERVICE WONT DO ANYTHING!!! I would add the receipt but it just a waste of time.

I bought a Maytag Washer in October of 2012. So far we have had to have repairs to it (4) times. The motor falls out. We are very dissatisfied with the product. We have always purchased Maytag products and fee we should get a new washer. The warranty is up in one month. If there is anything you can do to help it would be appreciated. A $1,000.00 for a washer is a lot of money for something that does not work and takes a week to get a repairman. Thanks.

My Bravos XL is worthless!!! This lack of agitator design is totally ineffective. Dark clothes come out with white powder on them and I use the liquid detergent. Whites I soak with detergent and bleach then full wash cycle. Still stains on dish towels and socks. Never had a problem with the old agitator Maytag. And yes the wrinkle free cycle creates wrinkles. Deep water wash is only cycle that even comes close to cleaning and its far from perfect. Horrible waste of money, buyers beware!!! I thought all those negative reviews were overblown and since I couldnt find a large enough machine with an agitator, I ignored warnings and bought this garbage. Matching dryer is fine.

RE: 5.2 CU Ft Top Load Washer, Model # MVWB865GW0, Serial # C84370937 - Purchased Jan 2019. The clothes come out terribly tangled and severely wrinkled, even when using the Wrinkle Control or Delicate cycle and occurs in every load size. Ive tried every cycle, including the deep fill and low spin speed but items are so wrinkled that whether I lay flat or hang or put them in the dryer, I have to iron them, which I never did before.

I have Maytag Model MGT8885XS03 Gas Range. I bought it in 2014. The surface burner valves, which regulate the gas flow, are a bad design. One valve got stuck and needed replacement within warranty. Then another valve got stuck about a year ago and the third one got stuck about a month ago. I am going to replace these two valves now. My friend, who is helping me replace, has similar gas range. He also needs to replace a valve. His range is about a year old.

Bought the washer in February 2012 for $900 at a local appliance store, delivery included. Just yesterday (10/16/15) a 5 cent piece of grey plastic flew out of the lid lock mechanism. Thinking this $900 modern piece of machinery painstakingly designed by intelligent people with university degrees would certainly work if I just stuck the plastic part back in. I just popped it back in, the lid locked, and the machine spun away happily (only having to run a correct cycle for an unbalanced load twice! What joy!) Fast forward 40 minutes, I skip down the stairs to go retrieve my flannel sheets (because its October in Pennsylvania, its getting freezing cold at night) and pull up gently to open the lid. It doesnt budge. About 2 hours later, following a screaming match and some furious googling, it was determined we would need two people to pop the entire top off the machine to extract my sheets.So in order to use the washer to clean clothing now, weve been unplugging the machine. Removing the three screws on the control panel (aka brainbox), unplugging the black and white wire from the brain box, taking the control panel off and sitting it on the dryer, and using putty knives to push in the metal clips holding down the top of the machine down, and prying the entire top of the machine back on its hinge. Then I can get my clothes out. Then doing so in reverse (dont forget to add detergent before shutting the lid! It will lock and you will have to pop the entire top off again.) to use the washer. All because of a 5 cent piece of PLASTIC. What brainchild figured, Eh, we can just use plastic for this important piece that the washer wont run properly without. It doesnt matter!? Someone that wanted to make $300 a pop doing service calls thats who.I cant believe Maytag has gone so far down the tubes. In case anyone else ran into this problem and needs to fix it, write down the model number, serial number, and other crud listed under the lid. Then use them to wipe while youre in the bathroom. All you need is the company and part number on the lid lock mechanism. According to Maytags website my washer doesnt exist. And there was no way, no matter how creatively I googled, to find a part for it with the Maytag model number. So now I have to try to find this measly mechanism to replace and try to use this piece of crud for a few more months. I guess my Christmas present this year is buying a new washer. And you can BET it will not be a Maytag.And two more things: with no agitator, you can fit really big stuff, but you also get to hear your washing machine dancing on your basement floor with an uneven load. No matter how many times you try to re-position items, it runs a corrective cycle, refills with water, and spins everything into a ball AGAIN. Also, the miserable thing is starting to rust. Right on the sides and near the lid hinge, and all around the bleach receptacle. How cheap, a washer on which the paint rusts right off with chlorine bleach.I wish I still had my Grandpas old 1930s wringer Maytag. At least I knew that one would work without a cheap piece of plastic. And at this point I might prefer wringing my clothes to hearing my washer try to escape. In short: cheap parts, no replacements available through company for DIY repairmen, company designed to force customers to use their servicing for $300 a pop. 1/10 would NOT recommend Maytag.

I wanted a small stove that did what a large/standard stove could do. I was worried that the heat would be weak but it cooks my food amazingly well. This stove has all the bling of a simple stove for a smaller price and size for my tiny house.

We purchased a dishwasher (Maytag) two or three years ago. We have had nothing but trouble with it. The welds on the upper rack broke. The wheels on the low rack keep falling off. Water leak happened recently. The start button broke. My wife and I decided to just get a new one rather than keep sinking maintenance costs which are going to keep adding up.

Maytag Bravos Model MVWB750wq1 - After only two years, the washing machine finally died. The machine was on a f51 code - hardly anything was in the washer. I also smelled a burning smell - well, that was the pump. The machine was not pumping water out. After the repairman came out, the contract company is saying they are not covering this because there was rust reported by the repairman. How can bearings inside a washing machine be rusted? This is a washing machine, isnt it? How are they building machines that deal with water and rust?! I will never buy another Maytag product - thats a promise. I spent over 2000.00 on this set. Never again.

Maytag fridge is a overpriced, ticking repair bomb. The fridge had issues with the compressor, control board (motherboard) and relay switch within a 12-month period. Customer service is weak in troubleshooting techniques and try to send the file over to a repairman. The repairman will show up at $80/hr + other fees and parts costing you approx $500, and still uncertainty that this fridge can breakdown at any time. Final advice: DONT BUY.

My husband and I purchased a Maytag Bravos washer and matching dryer in November of 2009. At three or four months old, the dryer quit drying and was emitting a weird smell and smoky air coming out of it. It was under warranty so a technician was called. A fan blade inside it had broken. The repairman replaced it and the motor as a precaution. There was absolutely nothing inside it that could have broken the fan blade and I always check pockets. My hoses were clear also. He told me that it looked poorly designed inside for air flow. He made a box out of sheet metal to fit inside it that he said would help it with air flow on the inside. I still have the dryer but I dont like it very much because it still doesnt do a great job of drying. It has to run too long and at too high a heat to dry laundry. The latch on the door broke a few months ago and had to be replaced too. I havent had problems with the washer as of yet. I like the washer and it washes very well but I will not buy a Maytag washer or dryer again. WHIRLPOOL OWNS MAYTAG NOW AND THEIR PRODUCTS ARE ACTUALLY MADE BY WHIRLPOOL SO I WOULDNT TURN TO THEM.

I purchased a Maytag dishwasher in 2010 model MDB6709AWW1. I only had it a year and the control panel went. They came out and replaced it and the guy told me that they were having a lot of the same problems. Now in 2015 it has gone again. It will run, but you cant change the settings. I took out the extended warranty on it and called 3 weeks ago and they sent out a local appliance repair company. This guy told me he had just come from another house with the same dishwasher with the same problem. He ordered the parts and I have been waiting 2 weeks. I called and the lady told me that they changed the part # and that they dont have any made yet and dont know when they will. WHAT!!! How can a company not have any parts made for their own dishwasher. I didnt buy the dishwasher when I bought all my other appliances, because there was a dishwasher here. It was gross and didnt work well. All my other appliances are Kenmore and I will stick with them. Have owned them for years and never had any problems.

MDB7749AWM1 more Maytag corporate garbage! I bought this dishwasher since my last one, Whirlpool, gave out at three years (garbage motor from Korea) thinking this would be a quality product made in USA. Well after about 6 months into usage and under warranty, the circuit board went out! The repairman assured my wife that it was rare to replace it on a Maytag. Now 9 months later, out of warranty, the circuit board goes out again! I know what it is, I can fix it, but will Maytag work on fixing to get a better circuit board? No! The US government is a puppet to all these companies that keep getting bigger and fatter! I say buy foreign products! Enough of these fat companies buy the competition out and giving the US public no option. Preston E. Tucker said it best: You let the big guys push the little guys out of the game and you will end up with garbage for products! Do yourselves a favor, buy Bosch, LG or Samsung. I know their products are not better but just maybe, someone in these corporate offices will see that to sell in the USA, you have to sell quality again!

I bought my Maytag Bravos washer and dryer set about 3.5 years ago when I moved into my home. There was a 20-year old set here that did work, but I wanted something newer and more efficient, so I donated the old set and bought these. Performance of the washer has always seemed mediocre, clothes dont get as clean as I think they should, whites are dingy, despite using hard-water additives and the correct HE products.A few months ago, the washer started a new behavior: stopping during the initial fill cycle and displaying an F1 error. I soon figured out if I hit cancel then start again, it would resume filling and proceed with the cycle. Over time, I had to repeat it more and more. Its now up to ten F1 errors both at the beginning and end of the cycle. I dont have that kind of time to babysit my washer. I already have a full-time job.I have called Maytag/Whirlpool twice now, both times getting unsatisfactory answers. Even after escalating to the customer service supervisor, I was basically told that it is most likely the control board that is the problem and since Im no longer under warranty (that washer ‘is’ almost 4 years old, maam), Id either have to order the part myself from their supplier (total cost $250 + the risk of DIY), or buy their service package for about $350 which included fixing that problem plus one additional years warranty.I pointed out that for a major household appliance that I (over) paid for, I expect a life of more than 4 years, especially since I had a working 20-year old washer when I moved in here. Since when is this acceptable? I could understand if it were a wear-and-tear part, like a rubber seal or something that moved constantly and would eventually need replaced. But this is the electronics module, something that cant (or at least, shouldnt) be worn down or broken by use or even user error. This is an integral part of the machine, and if it has a fault (which it clearly does), the manufacturer needs to stand behind it and help the consumer.What angered me even further is that the customer service manager even admitted that models similar to mine had had similar problems, and a free control board was sent to those customers. But my model was not in that range of production, so clearly they have no fault, in their eyes. Apparently, its not even remotely possible that maybe when they determined the range of models they believed to be faulty, mine hadnt been in use long enough to display the same behavior? Maybe the range they selected is too restrictive and they missed some. From the volume of complaints Ive seen online, Id bet that to be the case.I asked to be transferred to their legal department, and was refused because we just dont transfer customers to the legal department. Well, I just dont buy Maytag or Whirlpool anymore, and Im going to do my best to make sure nobody else does either. Im replacing this ** with a different brand, one Ill be sure has tremendous reviews and a manufacturer that will stand behind it.

I had to rate at least a one star because there isn’t a negative to rate. We bought the Maytag mvwb955fc1. First off it doesn’t clean our clothes. I can not get stains out or whites bright. I don’t feel it uses enough water. I put a full load in and it only fills up less than half with water. I try half loads and still not clean. It’s always shutting off when I wash sheets. Indicating it’s off balance. Today I started it before work and the lid exploded. I don’t think I want to even replace it at all. This could have seriously hurt someone. Do not buy this washing machine. The dryer is great so far. I wish I could post a photo to show you all.