We purchased the HE commercial brand for our family of 7. It has been running mostly fine for about 2 1/2 years. It started making a horrible grinding noise about 3 months ago. It was getting worse and worse. I decided to google the issue and discovered there was a common problem with a nut falling off the bottom. I leaned the washer back and found the nut on the floor, right below the center of the pulley. I reattached it by removing the pulley guard which had been getting cut by the loose and wobbly pulley, put some superglue on the nut and reattached it to the bottom. NO MORE NOISE!! Im willing to bet that this has caused slippage of the pulley, poor performance and many other issues. Maytag should do something about it.

Maytag Centennial Impeller HE Washing Machine - The seller left this piece of junk for us. I wondered why because it appeared brand new. After the first washing I knew why. I sure regretted leaving my old set behind. This washing machine wont let you add the amount of water you need. I had to add buckets of water and hope it didnt just empty it out because the sensor controls everything. Twice it just emptied it after I closed the lid and it locked. There is an impeller instead of an agitator. It moves slightly but not enough to move the clothes. To top it off the spin cycle tears into the clothing and twists and wrings it so hard everything is wrinkled with soap residue remaining even on delicate. Each load takes over an hour and the clothes arent even clean. It went to the dump after 4 washes. I went on Craigslist and purchased a used Kenmore and am in heaven. No lock, an agitator, 3 water levels, clean clothing, you can open it and add the missing sock, no sensor controlling how you want to do laundry and no more buckets. Dont buy a Maytag. Look at all of the reviews. They arent exaggerating, they are really that bad. Thank you.

Brand New 2019 Model 465 Washer and like others are saying is a piece of junk as they do not fill the drum with enough water even on the Deep Water fill option. The laundry does not circulate and nothing gets clean. Maytag is really poorly designed and manufactured these days and a complete Rip Off!

We got Maytag 2000 series front load washer just over a year ago. The bearings in the drum are already worn out. I will never buy a Maytag again.

I have a stainless steel dishwasher, model MDBH985AWS10. Its about 5 years old. The control panel works intermittently -- Ive replaced and ruled out the door latch -- now Ive got the problem narrowed down to either the control panel or the circuit board. Ive read about this diagnostic cycle I could run to try to help diagnose the problem. I emailed Maytag for the code and waited a week and didnt get a response.I called them today and they said they cant give me the code--they only give that to their technicians. My dishwasher is not brand new, but I paid good money for it, and Id prefer to not have to guess what to buy when Im trying to repair it. Each of these parts costs about $150. Im not sure what the policy is for other dishwasher manufacturers, but for the next washer I buy, Ill find a company that either 1) has more reliable products or 2) at least tries to help the customer repair his own equipment.

Our prior fridge died on a hot long weekend in July 2020. Desperate for a fridge, I ordered any fridge that could be delivered the same day. Received a Maytag which totally died 3 months later! Now I am waiting for a part (which apparently the Manufacturer has 100 in their inventory but havent distributed them to the source that ordered them). This is just the worst service I have ever experienced with an appliance. As so many people have said, I should have waited and ordered a European appliance. They are built beyond perfection and have excellent service.

I bought the Maytag Bravos Series 300 Dryer in 2009. In September 2011, the dryer wont start. I called Maytag. They basically said were on our own. It only lasted two years. What happened to appliances that lasted 10 years? I will never buy a Maytag dryer again.

First failed after 16 months. Second twice in 15 months. They are lucky to last 16-24 months. Stupid for a microwave that normally last 5 plus years for every other brand I ever bought.

I have had this washer just a little over a year and the sensor panel went out... For $600.00 it should not break right after the warranty goes out. Buyer Beware.

Fridge model # MSF25D2EAB00. I have had the fridge 3 years and 2/3 shelves have crumbled to pieces, the compressor has gone, the ice bucket crumbled, the ice maker stopped working, once ice maker was fixed it got stuck on crush, and now I am trying to order another shelf because it has also crumbled like the rest and this is in a household of 1 person! I am just getting the run around... I have been redirected to 3 different numbers now (800-344-1274, 866-368-6478, and 877-468-2371) and now I had a rude customer service rep so I asked if I could speak with someone else and I am now on eternal rot on hold. Pretty sure he didnt even transfer me and Im just sitting on hold on his line while he is laughing. Time to hang up and try again another day. #un**believableI was also told that if I purchased the extended warranty plan that it would cover the crappy shelves in the future so I did and now they are telling me it doesnt cover them and it only gives me a discount on them. MAYTAG YOU OWE ME A NEW FRIDGE... THIS ONE IS A LEMON! I have no clue what my order number is or where my receipt is at the moment but I could get a copy Im sure because I purchased it on my HomeDepot credit card so if you want it let me know and I will provide it to you then.

I bought the matching Bravos washer and dryer 4 years ago. I always bought Kenmore appliances but decided, based on the then reviews, that I would upgrade to Maytag. Biggest mistake I have made! I am a very tolerant person always looking for the best in anything. But I have to say, I hate both the washer and dryer. My clothes are faded, they shrink in the dryer even on delicate. I really cant say anything good about them. Today I washed 2 twin sheets, one king top sheet, and one very thin blanket. When I opened the washer, one twin sheet was on top and not even wet. So now I get to run another load and have to wait to remake my bed. When I have washed rugs on bulky, they are filled with soap when finished. Half the time, it doesnt spin out the water and I run a second and third spin cycle on a variety of items. I avoid doing laundry because it is so frustrating. I am retired so I cant afford to replace them. I just dont want anyone else to suffer the same frustrations!

I bought a Neptune washer and a dryer. I have had nothing but problems with these items since I got them. My washer keeps giving me a 3e code and will not clean the laundry right. I have used the H E detergent it requires and yet my clothes stink. My laundry smells like mold and mildew. I now dont have my units to wash and dry clothes. I paid almost $4,000.00 for the pair. I dont have the money now to replace them.

I purchased a new gas range in Nov 2013, but didnt use it until April because I was remodeling a house I had just bought. When I used it to cook Easter dinner, my meal was cold; the oven heats, then shuts off. Maytag has sent service techs 3 times. They have replaced the control board and the DSI module and ordered another part, for which we have been waiting over 3 weeks. Now they tell me it will be here next week. Maytag obviously cannot fix the NEW range, but they refuse to replace it. They deem it to be repairable though they cannot repair it. Customer service claims to be sympathetic, but will do nothing except schedule another service call and offer to extend my service warranty. What good is a service warranty if they cant repair the appliance? If youre smart, youll steer clear of Maytag and Whirlpool appliances. They are total CRAP.

The lid on this washer cracked twice. It is made out of plastic and is now discontinued. The lid cracks no matter how gentle you are with it. It is just over a year old and will have been serviced twice. The lid has to be ordered and you have to wait for a week. Maytag will not offer a new machine.

We purchased a MDB8949SAW dishwasher in 2013. 1 month after the warranty expired the touch buttons went on it. If you selected normal it would opt for something else like rinse only. We researched online and my husband followed instruction online to take the door off and seal the moisture to prevent this from happening. This worked for about 2 months and now back to the same thing. We paid $500 for this and just living with the problem for now. All we can do is warn others.

Purchased a Maytag Atlantis washer at Lowes in 2004. Until recently it worked without any problems; however, the agitator never seemed to work quite right. Normally, an agitator rotates in such a way that the auger action of the vanes pulls the clothes in toward the middle and then down into the water such that you have a continuous cycle of clothing being pulled down the middle, agitated at the bottom, then pushed up the outside. This one agitated but the clothing would just go round and round in the tub. Everything managed to get clean enough, but clearly something was amiss. Recently, the spin cycle became loud. A rumble became a loud roar over the course of a few cycles. Then I noticed water on the floor coming from under the washer. The short story is that the center shaft seals had just worn out. After almost 12 years of use, thats not surprising. Whats surprising is that it had worked so long without any issues other than the agitator.I took it apart and, to my dismay, the water had gotten into everything so that some of the metal parts were hard to remove. After having determined what replacement parts were necessary, I ordered them, but then placed additional orders for parts that probably would wear out eventually. So I ended up doing a near-complete rebuild. Other than the difficulty of taking some of the parts apart, and removing/installing the tub springs, it was actually pretty easy. I have reassembled, and now it seems to work flawlessly... so far. About the agitator: I found that shims are used on the transmission shaft to adjust tension. Too much tension and the clothes just ride around the tub; like mine did. Too little tension probably results in the thing not agitating at all (I dont really know). Once the washer is apart its easy to set the tension (insert the shim washers) correctly.There is a clip that holds the shim washers in place on the shaft. It was really tight; somewhat difficult to remove. One of the shims wouldnt fit when I tried to reassemble. As it turned out, that was a good thing. My research on this model revealed the way to get the proper tension. My assessment is that whoever assembled this washer at Maytag (or whoever builds these) assembled it incorrectly! Another thing I found out - after I ordered/received parts, unfortunately - is that there are two types of tub/shaft seal sets for this washer. I ended up replacing the newer type seals with the older type. Everything fits, but I may be losing out on a newer, better design. Well see. Overall, I am very pleased and impressed with the longevity and reliability of the MAV9501EWW washer. I have had Kenmore and Whirlpool; neither of which was nearly as durable and reliable. I hope this is helpful to someone.

My 6 year old Maytag 3000 series front load w/d set started leaking after 2 years. Minor leak on certain wash settings such as Rapid Wash setting that worsened (and I could live with), so that setting wasnt used. Last month the washer door was flapping open DURING a spin cycle. I stopped machine only to find the entire barrel had dropped and metal wire wrapped around clothing. Worst washer ever!

I bought a Maytag dishwasher in 2019 in Home Depot for my new home. The dishwasher stopped washing dishes after two years and 6 months. The price of the new machine was 700$ and I did not buy the extended warranty. The trouble is circulation pump, that cost to install the new one from local service would be about 350$ plus the new pump 150$. I consider quality is very poor if the new dishwasher works only two years and then it is better to buy a new item than fix the old one. Never never buy Maytag production.

I purchased a Maytag refrigerator on April 4, 2012. This week, July 12, 2015, my compressor went out. I called repairman and he said the compressor was shot. I thought this refrigerator would last longer than 3 years. I had to go purchase a new refrigerator from Home Depot in Knoxville, TN at a cost of $1,057.95. I am 80 yrs. old, on Social Security and this was a lot for me to put out, since the Maytag should have lasted a lot longer than 3 yrs. I feel I am entitled to some reimbursement. The Maytag is a side by side, Model MSF25C2EXB00, Ser. HR21112159. Im disappointed in Maytag and will never recommend or buy another one.

The design capacity of the dishwasher is not conducive to cleaning a full load. Within 3 months of purchase one of the interior baskets broke. I will never buy another Maytag product again. I was a fool in believing this was a top of the line dishwasher.

Every appliance in my kitchen is Maytag. I went with Maytag because its made in America and now Im annoyed. The microwave died after about 5 years and since I had a spare, I have yet to repair it. I am just now removing the panel to see whats going on in the inside so I can replace whatever broken part is broken. The double oven I have Ive had to repair twice. Once I had to replace a capacitor on the board because it blew. It cost me zero to replace it as I have an old home theater system I part out. The next item was the control pad itself which I tried to repair but had to replace for $200. The dishwasher died after 6 years of use and after replacing the control pad (couldnt be repaired), it still didnt work. And I got a replacement from my wifes dad who was moving and had to get rid of his. Ultimate timing. I purchased a Maytag refrigerator instead of a Samsung like an idiot (which I suppose I am at this point). The fridge leaks water because the drain plug is jammed and it will take a lot of work to get back there to unjam it. I think Maytag wants to sell you expensive parts that are doomed to break after a couple years of normal use. They want to send repair guys out to your house to charge you to fix their junk. I cant wait to move and buy all Samsung products and do away with this Maytag relationship once and for all.

My Neptune Maytag pair have been dependable. Great features. Now at 20 yrs old still kicking. Washer-front loader now has issue with fab softener going into wash correctly. Could be build up? Trying to self-fix. Very gentle with washing fine things. Hope I can keep going with them.

Maytag msd2650kes refrigerator - I replaced compressor switch three times then compressor went out after only almost four years. We bought all new Maytag when remodeling. Never again will we ever be that stupid again.

Have had this set for about three years (was a gift from my parents on having our first child), and its horrible. Clothes come out partially dry, with NEW stains on them, torn or frayed, and twisted into knots. Its supposed to be a high-efficiency washer but we often have to wash things twice to get them clean. We now have two little boys and Im starting to save to buy a different set (no Maytag ever again); disgusted that I cant even sell this set in good conscience. Will either be a donation or an eyesore for the landfill. Worst $1100 ever spent.

This Bravos 300 washer has never cleaned clothes adequately. I have 3 sons who are athletic and this washer does not clean sweaty or dirty clothes even with extra rinse. Now my machine is 4 years and 3 months old and it needs a new bearing which will cost me $385. The repairman said this is a common repair in this machine. Maytag should be ashamed of the poor quality of this machine. I am now looking to by a new traditional top loader. These HE machines are a joke. I am contacting them to make a complaint and see if anything can be done.

I dislike Sears and more so Maytag. I bought a Maytag Bravo XL MCT. It worked nice with very few hiccups until 1 1/2 years old. Then the washer went to the lock and done mode, thought it might be the lid switch down the washer up. Looks like I would need to change out the whole panel. Its not worth the trouble OR time to put one dollar to repair the piece of **.

Lets see... my complaints are the same as the others. I purchased the Maytag Bravos set. They were the higher end units. At first, the machine was very quiet. I quickly had a control board go out. Got that fixed. Now the washer gets off balance on every load.... Every time it spins, it stop. The gears whine very loudly... Louder than any other machine Ive ever heard. I agree with the comments on wrinkled clothes. It also does not clean heavily soiled clothes as well either. Overall, a bad decision.

My Maytag model MMV4205BAB microwave turns on and heats when the door is closed. We paid a lot of $$ for this overhead microwave and it has not been a satisfactory product. The turntable broke within a couple of months and now this. Im afraid it will burn my house down. This is a defective product and in my opinion it should be recalled. I have read several other posts about this exact model and problem. We purchased all Maytag appliances for our new home and we have had problems with all of them. The auger on the ice maker on the freezer broke within a couple of months. The handle on the oven door broke off while the builder was installing the appliances, and the top of the line dishwasher doesnt clean the dishes. It leave deposits on everything, no matter the detergent used. Ill never purchase Maytag again!

Purchased Maytag dishwasher model # MDB4709PAB3 8/2012 @ Lowes in NY with extended warranty. After a while, noticed wood floor warping in front of appliance. Called repair and after several tries, they couldnt repair leak under door. After many complaints to Lowes and Maytag, was finally issued a new dishwasher 8/2013 same model #. Person that hooked it up couldnt wait around to see if all was okay. Ran dishwasher after he left and as usual for this model it leaks worse than before. Called Maytag complaint dept and they said they would issue me another dishwasher of my choice and same price through Lowes. But they never spoke to Lowes and Maytag will not call me back. I would think there must be a leak problem with this model. Do not buy. It is not worth the trouble!

I am submitting this review today to express my disappointment with my Maytag washer. This is the Maytag MVWX655DW (Bravo), with Serial# C61842055. In August of 2016 I lost many treasured items due to a flood in Lafayette, Louisiana. My daughter and I were devastated and displaced because of this event. This is also in addition to completing Cancer treatment 2 days before the flood.I lost my GE washer which was a great product. It was a struggle for a long time, but we were finally get back on our feet. I was able to get another place to live, and it was time to purchase a washer. I was told that Maytag was one of the best products on the market, so I decided to purchase my first Maytag washer. This did not turn out well for me, and it was very disappointing. After 9 months of ownership of this product, it is broken! It is my belief that the product may have been defective.I put in a service call, and had a repairman come to my apartment on June 19th. I was told that my washer needs several parts to repair it, including a pump. I have never had this issue with prior washers. My previous washer before my GE purchase survived for over 10 years before it has had any issues. I called on June 26th to ask about Maytag issuing me a new washer or a full refund, instead of repairing this faulty product. I was told no, and was offered and extended warranty for 6 more months and $75.00. I expressed to her that I would rather have a new washer.The Bravo Washer is a very bad product. Instead of taking advantage of customers, Maytag needs to stand by that 10 year warranty sticker on the washer. Please understand this purchase is a LEMON. This washer did not last a year. After all I have been through, I did not need this financial hardship. In the long run, this product will die again. Unfortunately for me I may not be able to afford to purchase another washer. I am still getting follow-up treatment for my Cancer, and it is very expensive. Can someone please re-evaluate the need for a replacement washer or offer me a full refund? This product should not be broken after only 9 months of service.

I purchased my Maytag Neptune washer and dryer 5 years ago. About 2 months ago, my washer started making a lot of noise in the final spin cycle. Well, after I called my repair man (who I purchased the set from), they said that a back bearing is faulty. They suggested calling Maytag because the cost of the repair is $500. I called Maytag and was told that due to the age of my washer, there was nothing they could or would do for me. This is very poor customer service and very poor quality as far as I am concerned. I can hardly afford to get it fixed, but I also cannot be without a washer. Im sorry I have several other appliances that are Maytag in my home.

I had a GE washer and dryer when I first moved to my new home - lasted 15 years. Then... bought a set of Maytag and they have both been the biggest pain in the world. Spent 3000 and Im ready to toss them after 3 years. Dont buy Maytag!!!

We purchased a Maytag brand thinking it would be a quality long lasting machine. Wrong, the washer shakes from day one, We complained to Lowes, they brought out and installed a second unit, it does the same. The clothes dont get clean, sometimes you can see the blue HE Tide still on the clothes (sheets) after cycle is complete. Junk, waste of money, Ill never buy another Maytag product again. Dont waste your money on a Bravos Maytag top loading HE machine.

I purchased a Maytag energy efficient dishwasher in June of 2010 along with an extended warranty that I keep extending. Cost $ but needed. Issue: Sensor in Panel fails so far every year and needs to be replaced. The repair technician showed me the sensor strip and indicated that this has been a big problem. (At least I have a warranty; however, it is a big pain to have to schedule a service repair person to fix the problem.) Repair (Sears) is EXCELLENT with great customer service. I did contact Maytag and there has been no recall.I own other Maytag appliances such as a washing machine and refrigerator with no issues there. In any case, I needed to replace my clothes dryer and did not select a Maytag. I purchased a GE very simple product with no sensor/bells and whistles. Not sure if I will go back to Maytag in the future - depends upon how they handle problems with their appliances. I would rather pay extra money for quality, durability, and reliability than go through the inconvenience from parts that are not made well enough to hold up.

I purchased a Maytag over the range microwave a couple of years ago when I had my kitchen remodeled. I have had it repaired twice already. Each time, it cost over $150. I bought this product with confidence that it was a quality product. To say the least, I am very disappointed and I will never buy this brand again. My previous microwave lasted over 15 years without a single problem. The only reason that I got rid of it was to have matching appliances. It was not a Maytag. I am looking to buy a new microwave and I will be sure to look at the reviews to prevent being suckered again!

Purchased a pair washer/dryer Maytag Bravo XL module from Home Depot, Brentwood, CA #1076 branch. The first day I received my machines, the dryer had a defect. I called them within 24 hours to report the issue and requesting a return. Home Depot wont take it back; they said I have to go though the factory warranty to fix any problems. Its like buying a car, once you drive it off the lot its yours they said. 3 weeks after the washer started making noise. Home Depot kept delaying my claim for more than six month so I couldnt dispute the charges with the credit card company and avoid the California lemon law. I consider this a loss of money and time. Worst appliance purchase experience ever.

I bought the dryer (Maytag Gas Bravo Dryer) from Home depot in December of 2010. The thermostat went out in July of 2011 and has replaced the same part 5 times up until August of 2011. Then they put a new burner with a thermostat and it lasted till June 1 of 2012. Now the warranty is out, they want me to repair this piece of **. I will never buy a Maytag product again.

I purchased a Maytag dishwasher May 2019 Model# MDB4949SDE3 Serial# F80446835. It has to be one of the worst purchases I have made in a long time. In fact, I wish I could return it and start over with another brand. My glasses come out of the cycle with film and silverware is spotted. I have tried everything from scrubbing and rinsing before I put into the dishwasher, every product on the market, making sure my hot water heater is on high to settings for the longest most powerful cycle and it still continues to disappoint. My warning is DO NOT buy this dishwasher.

I cant warn you enough NOT to buy this design flawed machine. Ive only owned mine two months from Home Depot, the install was a nightmare and now due to a poor design flaw, if you miss loose coins or anything in pockets it will get trapped between the drum and the tub causing rattling and noise during spin cycle. Guess what? Service calls EACH time this happens. This is nothing more than a $750 piece of junk. I feel like its marring the whole feel of my new house. I hate hate hate this washer and am trying to get Home Depot to take it back, Maytag to refund me or sell it at a huge loss. This is NOT getting anything you pay for and I vow to NEVER EVER buy Maytag again.

I live in Southern Indiana and bought my appliance from Charlie Wilsons for 25 years. 3 years ago my Whirlpool washer quit filling up to full level. I decided to move it over and use for my car and pet towels. When I bought my hose in March 1999 every appliance was Whirlpool washer, dryer, refrigerator, stove, dishwasher. GE is made in Louisville, KY but I dislike the union.Anyway I bought a Maytag model MVWC415EW1 June 2017. Recently it started making a grinding noise when going in spin cycle, wadding cloths up and leaking black water on basement floor. Called repair shop out. I just do not have the time to repair stuff anymore. They came out $80.00 service call and tell me at least $300.00 to repair. Wait a minute. $500.00 to buy a new one over $300.00 to repair. Guess what I did? I called Maytag and complained. CASE NUMBER **. They reviewed and denied. Not a problem. I said, I guess you do not need me as a customer anymore.I have twenty year old Whirlpool washer and dryer still running, I have replaced my refrigerator (Old one in garage still running a colder than new fridge and day of the week). Bought Amana=Whirlpool and it has quit and replaced with a Whirlpool July 2019. Nothing is built like it used to be BUT we still pay as much if not more. Off I go to Charlie Wilsons to buy a $1000.00 Speed Queen washer with 7 years parts and labor warranty. Had to order it but old washer still running just not going to full mark.

Maytag Bravos washer and dryer both need replaced in 3.5 years! Control board had to be replaced on washer in under 2 years and now the replacement went bad in about 15 months. Maytag can’t help! Hundreds of dollars wasted. Dryer is not much better as the control board is now malfunctioning! DO NOT PURCHASE MAYTAG!

I have had my Maytag set for shy of 2 full years, of actual usage time, that is. My dryer seems to be functioning normally, minus an occasional lengthy cycle time, even after the clothes are dry. The washer however, is sitting in my garage now. F51 error code, which online told me the rotary position sensor was the issue. Yes, I was told by an A&E repairman, who was at the house for an unrelated repair, that it was the bearing that was bad. When he showed me what I was looking for, there was the bearing laying in the clear plastic housing, in the underside of the washer. Its going to cost around $350.00 to get the part, if it can be found, and the service call. No, not really worth wasting more money on it. I am very unsatisfied with this unit. With 4 kids and 2 adults at home, I expected much more from the Maytag name.

I have had nothing but headaches with our washer. We purchased it 4 years ago and after using it for a few months, I took it out because our clothes came out smelly and unclean. Called Maytag and they did nothing. So we went back to a regular washing machine and put this machine in the corner of the basement. I refused to throw away a $1,100.00 machine! So this year our machine quit, so we decided to try using the machine again to save us some money instead of buying another one... Well, that lasted for only a short time. Clothes still smell, came out unclean and just yesterday, the machine stopped rinsing and spinning! This machine has barely been used and its been nothing but trouble. Maytag service just plain sucks. They dont care about their consumers. I will never buy a Maytag again and I always let everyone I know to not buy this type of machine.

My experience over the past 2 years with my top loading Maytag washer is echoed in almost every review here. 1. Not enough water to clean the clothes 2. Clothes come out still dirty and covered with detergent 3. Barely agitates 4. Repeated repairs for leaking and computer board breakdown 5. Complete lack of interest by either Lowe’s and Maytag when contacted. I could write a long, detailed complaint but it has all been said quite well. We need to band together and file a class action lawsuit against Maytag. Any lawyers out there willing to take this on?

I purchased a Maytag Gemini April 22 2017 and I am very unhappy with it. The ovens are not working properly. I have thrown away so much food because the ovens won’t hold temperature. The display says it’s the temp. I set it but the temp keeps dropping and rising causing the bottom and top to burn and inside not to cook. Both ovens are doing it. Had a repairman come day before Christmas. He said there is nothing wrong. He said set temp, when preheat beep goes off wait 15 minutes for it to cycle then insert food. I tried this Christmas Day. Oven is still not working and again I threw away more food. I am so disappointed in Maytag. Serviceman is set up again to come out next week. I think I got a lemon. Please. I think they should replace the whole range. It’s not fair. I paid so much for this range and can’t use it.

A few weeks after I purchased my Maytag MEDC300 dryer in April 26, 2009, I noticed it gradually did not dry as hot as when I first used it but the element did not go out totally until April 2011. Now its November 2011 and the element is out again. Maytag is sending a service man, of course I have to wait until Monday, I am now inconvenienced 2 times in a year.Theres also what appears to be a burn mark on the back of the drum. Two years ago, I paid more than $400.00 for this thing and when it does work, you have to run it over and over again to dry your clothes. Wow! really energy efficient. What a piece of junk! I had my old dryer 10 years before an element went out. I did buy the Lowes protection plan that was sold with a No Lemon Policy. If the product requires more than 3 repairs for the same failure, theyll replace it, it says in the front of the brochure.In the small print on the back, it states 3 repairs for the same failure in one year. These companies are making money off us consumers who buy Maytag because of the name and what is supposed to be quality, and are ripped off by these insurance programs that say one thing but another in the small print. Big business is nothing more than robbers who get away with robbing the hardworking American people. When is it going to stop?

In 2016 I purchased a matching Maytag washer and dryer. The reason why I purchased it because I was in a house and I no longer had a washer and dryer and I refuse to go to a laundry mat at the city to go to Nebraska Furniture Mart and it was a number of different washer and dryer combinations available. I had previously own a Samsung matching washer and dryer and it worked fine, my Maytag has dame of the same features and works great.

I have a front loader dryer, model number MAH5500BWW, serial number A9147862ec. All of a sudden, I found water on the floor and after opening up the front door, I see where around the part that sticks of on the inside of the door, there is a big piece of plastic that has broken off and cracked all the way across the bottom of the door and is missing. It is allowing the water to leak down the front of the bottom of the washer and onto the floor.

Model MDB7749AWM2. Paid over $700.00. Figure I would get a good dishwasher so it would last and clean dishes. I was wrong. I replaced all new appliances for kitchen in house we had purchase 3 years ago. I replaced door switch 4 times, front door panel where screws go in broke off. Salesman at Lowe’s said Maytag was a good dishwasher. It is a stainless front and stainless inside. I have had cheaper models and never had problems with.

The way the side by side fridge/freezer is built contributed to several injuries. I am 60 tall and of normal size, and accessing anything in the side doors lower down always results in smashed head, near bleeding injuries. I am so sick and tired of it. No other fridge has done this to me. Add that to the shelves being near razor sharp. One of these days this fridge is going to land me in the hospital with a lawsuit. Most people are not 3 feet tall or 8 feet tall, thats the only way to use this fridge safely!

I have Maytag refrigerator that is only 2 years & 9 months old that I am told by a service tech that it has a sealed system leak. So the unit runs it just wont get cold. I have lost all the food that was in the refrigerator & freezer and I told by Maytag that its not covered under warranty. The tech gave me a ball park quote of $600.00- $700.00 to repair the unit & I lost at lest $200.00 or more in food. I cant believe a new refrigerator wont even last 3 years & they wont fix their problem. So much for buying American made products. Whirlpool YOU SUCK & SHOULD BE ASHAMED!!!

We can do nothing at the control panel even though the drum light will come on when the door is opened, we cannot turn it from the control panel. After a varying length of time, a fault code of F70 is displayed (which is not covered in the owners manual), the dryer can then be started by depressing the power button and all functions seem to be restored.

I have always loved Maytag but this top load washer is a bust. I purchased this higher dollar energy efficient washing machine to hopefully get the value out of it for years to come. Model MVWC565F. 4.2 Cu Ft. I use good quality liquid laundry detergent. I launder adult clothing (including business casual wear), sheets, towels and pet blankets. Occasionally the 20+ something children do their laundry while home. I often have dry spots on my clothes where they never got actually wet. I switched to only using the deep water cycle; however, this does not immerse the load in water. The smaller my load the less likely to get clean. Ive adapted to only have large loads but I still do not feel my clothes are getting clean. I often have to run the load a second time to not only remove ordinary day-of-wearing smells (very noticeable in socks for example) but to get them all wet and free of soapy/linty-like spots left on the clothes from the washer (most notable on black leggings, dress pants, etc). I always do my towels and bedding separate from daily clothing, so this is not coming from having a mixed load. I have also noticed that the load takes much longer (up to 2 hours) for my washing cycle. How is this energy efficient? It uses less water but more electricity? I miss my old fully-immerse-in-water washing machine that washed in under an hour! Love the dry that I bought with this but not the washing machine!! I do not recommend this washing machine!!

Buyer Beware! This is by far the WORST washing machine (Maytag Bravo) I have ever owned! The complaints are almost too numerous to list. Among them: Noise level is atrocious, water level is always low and cannot be adjusted, suds do not wash off, clothes do not come clean and get beaten up, takes an hour plus to do a load of laundry, frequently comes unbalanced, do not feel I can leave the house with this running, service calls have provided no fix, Maytag does not care. Do not buy! Saving my pennies to buy a different brand, will never touch a Maytag product again, Surprised there is not a Class Action lawsuit pending. When there is, Ill be right on board.

I purchased the Maytag Washer & Dryer $1891.14 with Extended Warranties Model numbers: MHW5100DW0 & MED5100DWo. In September 2014 from salesman ** at ABC Warehouse for my Wife as a Wedding Gift. The dryer started malfunctioning toward the end of October, it was randomly flashing a red light indicating Check Lint Screen and when this happens the dryer will lock up not allowing you the OPERATOR to dry your clothing. We ALWAYS check our screen before use and clean after each use, so we found that light to be odd. But anyhow we checked the lint screen and nothing was on it nor was it bent out of shape, everything seemed normal to me & my wife besides the fact we spent $1891.14 on BRAND NEW washer & dryer set thats acting weird. I called ABC Warehouse spoke to **. He said Yeah they do that sometimes, you just gotta MAKE SURE YOU BLOW THOSE THINGS OUT MAN cause they dont like it dirty. I explained to him we keep it clean then he said the screen might be slightly bent. He went on to explain how he seen that happen a lot, I just said uh huh uh huh yeah yeah. So now its like the middle of November and the DRYER Check Lint Screen Light is coming on before every load now and staying on for long periods of time not allowing us to dry our clothing. So I called ** again 2nd week of December this time asking for a new unit. He told me to call the ABC Warehouse Store Warranty Department at 1-800-722-3333. I called and they gave me a number to Master Tech Appliance 1919 Federal Blvd, Ann Arbor, MI 48103 (734) 662-0641. I immediately asked why am I calling technicians instead of new unit when my unit is still under the 1yr factory warranty and in addition too, I have purchased an 5yr extended warranty? They wasnt trying to hear that. So I called Whirlpool 1-800-253-1301 told them the situation and asked for a new unit they said NO and then added by telling me their policies and how many times they can come and attempt to fix my unit before replacing it. I screamed and shouted at them explaining to them that I have spent $1891.14 on a non-working unit for my wife as a wedding gift and I am currently drying my clothes at the local Laundry Mat, they said NO still.So I called Master Tech, they couldnt come out until Feb 3, 2015. My wife took off from work. In the mean time it completely stopped working the first week of January, we had to go to the Laundry Mat every couple days cause we got 4 kids. SMH WOW my wife is pissed, I mean furious. When ** from Master Tech showed up he looked at our unit and said its also not getting hot so he called in to his job they told him to come back and order my parts and to schedule another day to come back. 2 weeks later Master Tech called with the appt. My wife took off from work again but this time they called the day of hours into the day to tell us the parts are on back order and they need to reschedule. My wife was VERY UPSET but we did it anyways. Now remind you are dryer is still out of commission. Were going to the LAUNDRY MAT. Master Tech came 3 days later (my wife took off from work) they literally took our dryer apart (Pics Below) for it to still not work, Master Tech called Whirlpool, Whirlpool told them to order us a NEW SWITCH BOARD. Wow what the hell are you serious? So Master Tech leaves again and orders the SWITCH BOARD. They came 5 days later (My wife took off from work) new switchboard and dryer still not working. Now throughout this whole ordeal Ive been in contact with all 3 companies begging for a new unit and nobody wanted to hear that especially WHIRLPOOL & ABC WAREHOUSE. With Whirlpool knowingly the switchboard didnt fix the issue the first time, they instructed Master Tech back to my home with the same but NEW SWITCHBOARD. LOL WOW I CANT BELIEVE THIS IS HAPPENING TO US. Master Tech schedules yet another day to come by 3-13-2015 & yes my wife took off from work AGAIN just to hear ** say sorry they keep sending me back with the same part and they know its not gonna work but anyhow Im here. He switched out the Switch Board again and still nothing. I called ABC Warehouse and they finally okayed us a new dryer with delivery day of next day, which is today 3-14-2015 and when it arrives THE WHOLE FRONT DOOR IS BENT OFF THE HINGE WOW WOW WOW WOW. Now they say our new will be delivered 3-17-2015 and yes my wife has to take off from work.Updated on April 9, 2015: 3/17/15 ABC Warehouse replaced the 1st broken dryer to only return with another broken dryer, same problem, red check screen light flashing & dryer wont spin. They left here.

Updated on 02/13/2021: Maytag stove purchased 15 years ago for about $500. Replaced mother board about 5 years ago which wasnt cheap, but otherwise, stove has performed with no problems and still looks and behaves like a new stove.Original review: Our 6-7 year old well cared for Maytag range oven recently stopped working. After a service call for diagnostics, it was determined the electronic module controlling the clock and all oven functions was dead. We were told by the Maytag service tech the module cost was 300$. That cost plus labor for less than an hour, plus the 60$ diagnostic visit came to almost 500$ which is close to cost of a new stove. The technician answered yes to my question, Do you replace a lot of these? He also said the cause may be power fluctuations making me think that surely there is a way to prevent this kind of failure. So, since the price seemed exorbitant, I wrote Maytag to inquire about causation/prevention, etc. I received a fairly prompt and polite reply with totally no explanation. I wrote another email with relatively the same results. I dont recommend buying an electronically controlled Maytag stove.

I purchased a Maytag Dishwasher #MDB7749SBM1 as part of a complete kitchen remodel less than 3 years ago. Maytag was a great product years ago so I thought I would switch from GE to Maytag thinking that I had purchased a quality set that would give me years of great service! What a bad choice to say the least! This dishwasher has never dried the dishes completely with heated dry option. I never cared for the plastic latch and metal catch option either since I caught water dripping from the bottom since the door must not have been completely shut even though the latch was secure.Most recently, the start option on the flat control panel will not work. After opening and closing door multiple times I can get the start option to light up and run the cycle. Added bonus to start option not working correctly is that when the dishwasher door is shut, it automatically runs hours later with no human interaction. The dishwasher lights were lit up like a Christmas tree at 7 am this morning and running a cycle. Guess it thought the dishes werent clean enough. I am going to price out a board and determine whether I will throw this piece of crap in the dumpster and find a different brand! I HIGHLY RECOMMEND THAT YOU DONT BUY A MAYTAG DISHWASHER!

Leaked and leaked, spent hundreds on never ending problems from day one. No support from Maytag. I was told by Sears salesman it was the best you could buy. Our old washer lasted 30 years. This one never worked right - dead at 5 years. Shame on Maytag.

Just after a year the bottom freezer began to build up frost. I had to thaw it every day. A repairman changed part and ran well for about 5 months when it started to frost up again. Again, I had to call a repairman in. $500.00 later, my fridge is working again. I am done with Maytag appliances. Never again!

Dishwasher cleans well, but the control console has failed again & only responds to two functions. After replacing the console a couple of years ago with a new unit I thought it was done (it didnt get much use). Is there any recourse for this complaint? All I want is a new console panel. Maytags brand is apparently only good on the commercials. Very disappointing. Also, the top rack is very awkward & is only good for short glasses etc.

When my stackable washer finish its complete cycle, there is water left in the tub. You can manually turn the tub and you can hear water sloshing around.

I purchased a Maytag Bravo xl washer & dryer for $1600 in May 2017. Sunday, the user interface panel went out in the washer. After an $85 diagnostic visit, we were told it would be $500 to repair and take an additional 5 days. My husband is recovering from major knee surgery so I was short on choices. I elected to purchase a new speed queen and will never purchase Maytag again. The 10 yr warranty tag on the front is useless!

I love my Maytag. It does a good job, however, it takes almost an hour to run one load. Also, if you have a heavy load, it doesn’t spin long enough so your clothes are dripping when you take them out.

We have been totally pleased with our Maytag Washer and Dryer BRAVOS XL units from day one. Their advertising is Spot On correct. Follow the directions for periodic cleaning and all is well. The only issue weve had is low water on some wash cycles. But these are Eco and Environmentally friendly units. So we learn how to use the machines for best performance. We would definitely purchase these again.

After only about a year or so - and it is out of warranty - the clothes are not clean - there are white type of scum marks left on clothes and especially dark clothes. This is even after I use the recommended detergent and less than normal and do a double rinse. Have to wash clothes again with no detergent with a double rinse again. Just so annoying. Would never buy Maytag again.

The engineering of all these new machines are totally useless. Bring back the old tech. They DRY wash, NO WATER, they take forever to finish, wasting energy, clothing not cleaned. They are very noisy, doing nothing. Time to recall all of these units. They are totally useless.

We purchased a Maytag dishwasher in July 2013. In October 2014 it stopped working. None of the buttons on the control panel would light up. The service technician diagnosis was that it needs a new control panel at a cost of about $200.00. We chose not to do the repair since the technician recommended against it.

I bought this Maytag Dryer in May 23, 2015. I had nothing but problems. I had 4 techs come out and say different reasons why it does not work. I had the vent exhaust clean out. Still not working, the one tech said there was not enough clothes for the dryer to sense it wet. I did a huge load, still doesn’t work. The sensor for the vent keeps popping up and it’s cleaned. I have to pull it out and in to get the signal light out. Cant turn on the machine. It still does not work. I tried contacting Lowe’s, since I bought an additional services plan. They said I have to call every thirty days for three months. That means I have to take my time out of work and wait for a tech for three months to get make a complaint and TRY to get new one. I really disappointed with Maytag and Lowe’s. I have a tech coming out this Monday, 11/23/2015 for another services call. I will never buy at Lowe’s or Maytag again. How many times does a certified tech from Maytag have to come out check a brand new dryer?

I purchased a new Maytag from Home Depot. It was delivered and installed by them on 7/20/12. Today is 9/18/12. It is less than 2 months old and the tub is starting to shred around the upper rim. I called to get it repaired. What a nightmare. First I tried to understand a Filipino woman through a bad connection. She advised me to call a different customer service number, 1-800-688-9900. I talked to Crystal. She called up information on me using my phone number. She asked for the serial number as she had the model number available from the online registration I completed on 7/20/12. I told her I do not have that and asked where it was located. I also told her that I was unable to get it at this time as I am handicapped. She advised me that I had to show my repairman the receipt or I would have to pay a $60 service charge. I get nervous about throwing good money after bad. So I then asked why. If the serial number is so important, why is it not a required info when you register online? She had no answer. I asked to speak to her supervisor. I waited 4 minutes. Enna finally came on the line. She gave conflicting info about my online registration. She said I was not registered online (if not, how did Crystal have all my other info including my model number? Why did Crystal tell me I had registered without the serial number?). Enna told me that the repairman could key in the serial number when he gets to my house and if my washer was under warranty, I would not be charged. Again I asked why, if the serial number is so critical to the process and with all the info they seem to have on me (name, address, phone number, model number, place of purchase, date of delivery, etc.), why is the location of this very critical number is not in the owners manual? Why do they allow you to register without it online and why dont they track sales and delivery by serial number? She was unable to address these issues. I asked to speak to her supervisor. She told me she would give me her supervisors name and number (Kim, **) but she would not give me a last name or contact information. She told me that she was the highest level that I was allowed to speak with.Bottom line, my Maytag is falling apart, getting through the red tape to get it fixed under warranty is silly. Maytag ignores its own concept of tracking by serial number and does not support the use of serial number by telling you where it is located on an appliance or requiring it to register online. Calling customer service is a joke! I was mad when my new $800 washer started to fall apart. Now I am just sad with the way we allow manufacturers to treat us. Mad about the way we allow them to operate in the United States. They create junk or junk parts overseas, products fall apart over here, calls for repair get routed around the world, and then they create more red tape and call it customer service. I made one bad choice. Hopefully, you are reading this and can avoid your own.

When I attempted to contact Maytag about an issue in my 3 month old washer all I received is an automated email back saying to contact one of the repair places on their website. There was one, so I notified Maytag I would contact them. I contacted them. They said Maytag had not notified them that this was a warranty repair and if I wanted them to come out I would have to pay for it. I have attempted to contact Maytag several times to get this straight. Guess they are trying to wait out the warranty to respond. Will NOT EVER buy another Maytag. Too bad they used to be a good product.

The stove functions are excellent and the temperature of the burners and oven causes the food to cook even. However after about 6 months the heat from the burners causes the coating on the stovetop to burn like its baking and it cant be cleaned. Now the coating around the burners is horrible and burnt.

I have used several brands of refrigerators and Maytag stood out for me. Everything works as good as new. However, my experience with ice machines, has been the first thing to quit.

Bought in July 2014, third service call already! To replace my 6 years old Maytag Centennial thinking I was doing a good thing to upgrade to an HE... HA! Jokes on me! Washing machine: Water level. How can you wash clothes in 1 inch of water??? Noise. Very noisy at every cycle. Shakes and easily unbalanced. Clothes are still dirty after wash (obviously if not enough water). Dryer. Noisy with sporadic blower sound (like a plane taking off - high pitched). Three service calls in 6 months??? 2 calls for cable suspensions and now waiting over a month for the tech to change the drum completely. Good thing that I took an extended guarantee, for an extra $300.00!! After Ive read the over 400 complaints about this product, I really feel like I got screwed! My last Maytag EVER!

My refrigerator temperature control panel started flashing lights and the ice maker flap started opening and closing over and over. I checked online and there are numerous model #s doing the same thing, most all contacted Maytag, some were fixed for no charge. Some were not even though they admitted there was a defect in the electronic control panel. I was one of the ones they refused to fix because they said it was an older model but they fixed a 2006 model, a defective part is a defective part no matter the age especially if they know and admit there is a problem with the control panel.I cant understand why they wont take care of their problem, so now I have to spend over $300.00 to fix a problem that they made in manufacturing, that is not an outrageous amount, thank goodness, but I just dont understand why they wont stand behind their product when they can fix out for probably half that cost to take care of their problem. I didnt make the refrigerator, they did.

We bought a new Whirlpool dishwasher, and it was a nightmare. So after four years of that we tried their sister company Maytags dishwasher. I have to say that I think these two old American brands have been ruined. This Maytag dishwasher is always making my dishes smell like rotten fish or a dead animal. I have to dump bleach and or vinegar down in the bottom constantly to keep the stink down. And I have looked and there is no food laying in the grinder. Then we started to lose wash cycles, and the buttons (not real buttons but a cheapo control panel) started to malfunction after 2 years. Now, 3 years into it the plastic adjusters in the top rack are broken, control panel has gone totally haywire, and still smells terrible. I remember when American appliances were sturdy and reliable because they were designed by engineers. Now they must be designed by accountants and shareholders. Goodbye Maytag and Whirlpool.

We bought a Maytag French Door 21 cu. ft. refrigerator in 2008. 2010, 3 repairs later, the ice machine went out, we went back to ice trays. Now the compressor died. The old ad of bored Maytag repairmen cause they never need repairs is bogus.

My Maytag has been out of service more than in service and this is my 2nd one in 2 years. They replaced my first one due to breaking down several times. I have spent so much $$ at the laundromat after paying big bucks for a washer.

I purchased a range 5 months ago. It is STAINLESS STEEL. It began to rust. I called customer service and they told me it was cosmetic, so they wont help. I think a stainless steel range should not rust after 5 months. Very disappointed, WILL NEVER BUY MAYTAG Again.

Our 3-year-old Maytag Quiet Series 300 dishwasher continues to have problems, especially with electronic keypad, which we had replaced (exactly) 1 year ago. The issues are: currently (and previously) not filling water; leakage around gasket, which we replaced twice. I read in other related posts that fire hazard has been flagged as a potential problem. Im not surprised as I cant tell you how many times this machine has gone through the motions (cycles) of appearing to clean, then we discovered that it has not cleaned anything, despite being very hot (and dry) inside the unit. Stay away from this brand.Multiple service calls and replacement parts we incurred at our own cost, in addition to many episodes of inconvenience to our family.

Purchased a new Maytag dishwasher three years ago. After having it for one year the panel box no longer worked. Had to pay $300.00 to repair. Now half way through washing the dishes again no water will go into the machine. Only the first part of the cycle. I am sure it is going to be the panel box after reading other peoples problems with this machine. I will not pay to have it fixed this time. I will have to buy a new dishwasher. I will never purchase a Maytag product ever again. I have lived in my home for 40 years and never had a problem with any appliances. This would have been my third dishwasher in 40 years and as you can see it has not even lasted 4 years. I will inform my friends to stay away from Maytag.

Washer knots clothes into unmanageable tangle. Poor rinse leaves soap scum unless rinse extra, thus not conserving water as appliance is supposed to do. Load easily becomes unbalanced and unable to restart machine if paused to rebalance load. Will never buy another Maytag washer or dryer.

Horrible washing machine. Cannot get clothes clean. It simply does not supply enough water to wash. Have tried everything. I want my money back. How do you start a class action lawsuit. Thousands of people are dissatisfied also.

I bought as a pair the Maytag Heavy Duty Washer and Gas Dryer 30+ years ago The pair are like a Timex watch --takes a licking and keeps on ticking. They have never failed me and I have never had to call the Maytag repairman.

Maytag wont fix new washer. Service person came 3X, but it still wont go to rinse cycle. Last 2X Maytag said service scheduled, but no one showed. MT mgr said cant help & to just keep calling back.

In July 2012 I purchased a Maytag BTM standard door refrigerator from Home Depot. Approx. 2 weeks from the 1 yr. Standard warranty July 2013, my refrigerator started cycling like every 20 minutes and loud popping noises started occurring. 1st service tech would only stay 15 minutes & did not want to stick around to hear the noise. Ran the standard tests and said everything was fine. That was around Aug. 2013. So I put up with it for a few more months and finally the popping noise was getting louder. 2nd service guy (Jan. 24, 2014) got to hear my video recording of the refrigerator cycling and loud popping noise. He replaced a bad dul part (Note: they all wanted to blame it on our ice maker that we never ever hooked up). Oops...wrong diagnosis. Whatever he replaced stopped the constant cycling pattern but now the popping noise is getting even louder like a shotgun going off. 3rd repair guy (Feb. 20, 2014) tells us that is normal and recycle product material is not that good nowadays?? I pay a $1000.00 for a noisy refrigerator and they say it is a normal sound. I dont think so. The refrigerator is now popping so hard that the right side of my refrigerator that faces the open is now buckling due to the compression of the heating and cooling which is causing the loud popping noise. If you rub your hand down the side of refrigerator you can feel the waves forming on the side of the refrigerator. Trying to get a Maytag rep out here. Something needs to be done about the production of these bad appliances.

Almost two years after purchasing the Maytag Bravo XL, I am fed up. I have the exact same problems as everyone else in these reviews. Soap scum left on dark clothes since day 1. I thought maybe I was doing something wrong. I have read and re-read the manual especially the troubleshooting guide and still have the same thing happen. Its very frustrating. I constantly have to re-rinse clothes because of soap, lint, dirt, etc left on clothes. I wouldnt give away this washer to anyone, I would rather burn it. I am currently looking for a new washer, the last one I had for 11 years was a front loading Whirlpool. I should have stuck with a Whirlpool, I still have the matching dryer no problems at all.

We purchased our Maytag Neptune washer and dryer in 2006. Months after our purchase, we tried every HE detergent we could find to see if our towels would smell fresh. Nothing we have tried has worked. I just went to Maytags web site. I found out there was a recall on this washing machine due to the mold on the door gasket. Why didnt they send me a recall notice so this could be corrected with a refund or something?

We purchased a complete, upper-end Maytag kitchen package from Lowes. So far, the MMV5208WS microwave has gone out 3 times; it was the magnetron all 3 times. The last time was a few weeks after the warranty ran out. After a lot of discussions with Lowes management, they then took it back and gave me choice of any brand. We picked a Samsung and have had no problems so far.As for the MDB8859AWS dishwasher, it was just stuck under the counter for the first 6 months of its life, because we were in the middle of a remodel and it wasnt plumbed in yet. Once we got it working, my wife loved it. Weve used it maybe 40-50 times since she was still hand-washing small sink-loads of dishes. A month or so out of warranty, it went out. There were no lights on the keypad and everything was dead. We thought it was the main control board, but it wasnt. Next, I tried the keypad, because Ive read many posts about these 2 things seeming to always go out on these models. I still have the fridge and stove, and hopefully they fare better than the microwave and dishwasher.What kills me is when I look at my old Maytag dishwasher and Samsung counter top microwave in the garage; both 15-20 years old and still worked just fine after getting replaced. It has never had a repair of any kind. I went out and spent $639.00 (it was on sale, the regular price was $799) on a ** dishwasher and it didnt even last a year. The microwave was close to $400, and it was on sale. I think my old Samsung microwave cost $79.99 when I bought it. You used to get what you paid for!

I bought my Maytag washer and dryer in Monroe County in Georgia, USA in 1980. Its a 1979 product and it STILL works perfectly fine after 40 years! Im 64 years old now and Im hoping Ill never have to buy a new set although I would love one because theyre so pretty these days.

I bought my Maytag stand alone dishwasher model # MDC4650AWB in August of 2009. I have used it once or twice a week since then. About 2.5 years ago the control panel crapped out. I forked over the $$$ to have the part replaced and installed. Now, 2 years later the panel is once again slowly dying. I just got off the phone with the Maytag people and they refuse fix it and take responsibility for the product failure. The machine has worked adequately for me aside from the control panel issues. The control panel was built to break. Shame on Maytag! Lets go forward with the class action lawsuit!!!

I bought my Maytag Refrigerator about 7 years ago and the night mares have not stopped. The ice maker has broken down so many times, I forgot to count. The drip from the ice maker lands on the floor of the freezer and drips out to the floor. The cold part of refrigerator end up freezing the fruits and veggie and milk.

I bought this Maytag MCT washer and dryer set brand new from Lowes October 31st, 2016. When I washed the first load it made so much noise I thought it was broken. Called Lowes and they said it is just noisier than the older ones. This is the water/load sensing model, supposed to be great. I am usually here by myself, so at most I wash one load of clothes a week. I have a queen size mattress pad in there washing right now. This pad fills up the drum pretty much, I have it on deep water but that only gives me maybe 1/4 of the drum that has water in it. The pad is wet from wicking, NOT from the water covering it. How is this supposed to clean anything when the water is not covering the items?When it spins out, it gets off balance easily. The manual says to not worry about balancing load as you put it in there, but doesnt make any sense to just cram on one side as the water isnt going to float the cloth around to balance. The settings for Bulky does nothing more than the setting for Deep Water, you still do not get enough water to wash your clothes.It also does not do any good to add fabric softener to the machine, as it seems to just take it all out, you cannot smell any fabric softener on your laundry when you are transferring it to the dryer. And the laundry when dry isnt soft like it was with the old machines. I will be 62 in December 2017. My parents always had Maytags, never a problem. This is the 4th set of Maytags I have had. And bought a set for my daughter in 2013 also. And this by far is the worst. Their quality is completely gone now. Nothing but cheap made products that are predestined to fail. Friend across the street said she had looked at this set when she was in market to get a new set. She has an friend who works on appliances and who works for stores selling these models and he told her, they were not worth buying. Wish I had known that. Do not waste your money.

I purchase a Maytag dishwasher from Home Depot on 12/31/11. Based on the their commercials, I thought they were dependable. I did purchase an extended warranty, as I always do with any new appliance. After 2 years, the dishwasher stop working. I contact Home Depot and the extended warranty and was told to contact the manufacturer. Maytag blamed the extended warranty for the problem. They told me they could not help me. And could not help me. I will never ever buy any appliances from Maytag again. This model is M936/110V cord.

I saved for this refrigerator for some time and assumed at my age this would be my last one. Thats a joke, less than 2 years and I see this water leaking on my floor. I blamed my dog at first. This was a Home Depot purchase. I love the middle drawer but the freezer has this problem. I removed the ice but it comes back. I did not purchase the extended warranty because if you have an excellent product, you dont need an extended warranty. And of course this happened RIGHT AFTER the warranty ran out. I am VERY upset with Maytag/Whirlpool. Will NEVER buy another product from them. This fridge should not have problems in less than 2 years.

The oven hasn’t caused any issues. It’s beautiful stainless steel and black finish creates a shiny but modest finish to my kitchen. It’s self cleaning power is also useful and saves time and where I come from time is money. It cooks food evenly just as an oven should.

The washer is very aggressive - it will tangle the clothes and actually tear them if they are thin. There is little control with the speed or water temperature or with the amount of water for a load of clothes.

Purchased Maytag 4000 series washer Feb. 26 2011 - within six months Maytag warranty replaced the drum and bearings, within another few months Maytag worked on the drum again. Year two started out with the warranty contract replace the drum and bearings again. Oct 1 2014 called for service again, the drum not moving and having to wait 2 weeks for Tech. to checkout the machine then order parts. I have 7 children at home and that didnt matter to anyone. After reading online the number of 4000 series Maytag machines with this problem somebody needs to make Maytag recall and replace them.

After owning my refrigerator for about six months, it started to reek, the smell permeating all of the food in the fridge. After cleaning and disinfecting the fridge and throwing out all of the food I found that the smell was just as bad as before. When I checked online I found that Maytag owners have been complaining about the smell for over a decade now. It is caused by a poorly installed drain pan. The fridges design directs air flow so that the smell enters the fridge and distributes it evenly throughout the fridge.

My old washing machine was about 25 years old but still doing a fantastic job getting the laundry done. When the dryer died we decided to replace both machines so theyd match. I had been setting money aside for years in preparation for this purchase. Ive only had them for two weeks and I stay awake at night wondering what GENIUS decided you can get clothes cleaner in a tablespoon of water than you can in an adequate amount of water?! My old washer could wash a load of laundry in about 20 minutes. Again, what GENIUS decided taking over an hour to wash a load of laundry in a tablespoon of water was a better way?! What working woman would choose to double the time needed to do laundry and then not feel confident that the clothes are clean?!!! I am so mad and frustrated and disappointed and I dont know what to do. I wish I could yell at somebody!!!

Purchased top of the line Gemini oven a few years ago. Lower oven stopped working. Maytag repair said igniter not installed properly at factory. I contact Maytag customer service to see if they would help with repair cost. Rude response from them... basically saying anything fails after 12 months not our fault. Rejected my request without even asking details about product which model etc. Unilateral rejection. Horrible customer service. I will never purchase Maytag appliance again. Horrible, horrible, horrible. Avoid this company and their products. They do not a good product and they provide terrible customer service.