Would give them 0 Stars if that was an option. Bought a Maytag washer and dryer in Aug 2021. Washer broke Jan 6 2022. Called Maytag/Whirlpool on Jan 6 as it was still under warranty. They only had one service company in our area to work on the washer. I called them and it took them 10 days to come see what is wrong. Ordered parts. Said it would be 2 weeks. We are now 6 weeks into this with no parts. Called customer service and they said they were notified that their service company needed a part and would take another 21 days to resolve. Talked to a supervisor (Demetrius) who sounded like he did NOT want to be in that position. Offered no solution other than we will just have to wait. Threw a 3 month extension for the warranty on which still does not fix the problem. Sad to see this company go down the tubes as it was once a pretty decent business with solid products. No longer.

Maytag Dishwasher MDB8959AWS6, S#F15006566 purchased 12/28/2011. Here is a record of the product repairs done by All Tech Appliance Service in Portland. 1/12/2014 - Thermal Fuse and Control Board. 10/15/2015 - Thermal Fuse. 9/2/2015 - Thermal Fuse. 12/5/2015 - Unit stopped working again, strong electrical smell, probably Thermal Fuse again. This dishwasher product has a design defect. It should be recalled.

We (family of 2) purchased our Maytag Bravo XL Washing Machine Model#MVWB880BW in Nov. 2013 for over $700.00. Last week, Dec. 2019, the washer would not finish the rinse/spin cycle. The clothes were still wet. I researched troubleshooting in the Maytag booklet included with the machine and tried everything. It still showed an OL on the readout. It was not overloaded as I only had 3 towels, 3 washcloths, and 3 hand towels in the washer. I tried just the rinse/spin cycle alone to get the water out of the clothes, but they remained wet, and the OH still appeared on the machine. When I called the place where we bought it, they suggested unplugging it, waiting and plugging it back into the outlet to possibly reset the machine. That seemed to work for 1 very small washload. The next day, I tried washing again and the OH appeared with the clothes still being wet. We had a repair person come out. The service call/diagnostic of $116.98 plus repairs of $304.41 plus $95.00 to install of the new Motor Control Board. I feel that cost is excessive for only 6 years of service. Before we bought this machine in 2013, I had a Maytag which lasted over 20 years with NO problems. I always thought Maytag was the best washer, but this experience has proven to change my mind. We went out and bought another washer rather than replacing the board not knowing how long the new one would last. Needless to say, we did not buy another Maytag. I do not feel I can trust the Maytag products anymore. After this experience, I did more research on the Direct Drive used in this particular model washing machine and found that it had been problematic. I would have thought Maytag would have offered a recall to avoid these costs/problems and avoid dissatisfied customers. Along with the original purchase of the Maytag washer in 2013, we did buy the matching dryer and are hoping the dryer will last longer than the washer. We shall see.... This has been an unexpected and expensive lesson.

I purchased my first and last Maytag double door bottom freezer in Aug 2018. The ice maker shoots ice out all over the floor, only half make it into the glass. It also sounds as though ice is falling down inside door. I had the ice maker replaced twice, the gasket as well, the back removed to check for water line blockage NO avail. Before the first ice maker replacement it sounded like a freight train. I questioned whether I had received a store second from Home Depot or a return as the stickers inside had been removed but HD couldn’t assist and Maytag didn’t care. Definitely NOT worth the 2000 I paid.

We purchased a Maytag Neptune series washer/dryer set approximately 5 years ago. This is the 2nd time in 5 years that we were told by our local repair person that the drum of the dryer got bent out of shape. This is from normal use and due to a bad design on their end. Maytag refuses to foot the bill (about $350-$400) as it is out of warranty.

This is a wonderful washing machine. For cleaning clothes it does exactly what you expect from a washer. We have had 2 Neptune front loaders. They, however, have a couple flaws I dont want to live with again and will be looking for one that has come up with the solution to them. One, the bearings on them need replaced on a periodic basis or it sounds like a 747 taking off. Two - the front gasket around the barrel has a mold problem no matter how much you try to keep the thing clean. Other than that, these machines perform fantastic.

Purchased a Maytag washer for my family of 8 because we do a lot of laundry and our Samsung washer failed after 3 years. I thought Maytag was a more reliable brand and was hopeful. The machine stopped working after less than 4 months of service. Manufacturers warranty repair came out and said it needed three new parts, motor, clutch and chip - said it would be another 2-3 weeks depending on parts. So all total without a washer for 4 weeks minimum - call the customer service people (first one was rude and short), 2nd one after 45 minutes on hold - told me the were no other options other than wait for the repair. Four months after a brand new washer and it failed. I requested a replacement option and they said no way. Their hotline talks about a positive customer experience and that seems to be a joke. Not helpful, super frustrated and they do not seem to care about the customer experience at all - terrible product and service

I read some of the reviews on the Maytag ovens. I too have the same problems! Have had control panel replaced and still have to set at 400 if I need to bake at 350. It also takes forever to preheat. Trust this review because I am one very unhappy consumer!! DO NOT buy Maytag!!

I bought a new smart washer and dryer from Maytag in mid-2019. Beginning in the first few weeks the machine did not perform as expected--cut off in middle of cycle, door failed to unlock at end of a cycle, constant error messages that made no sense (power failure when power didnt fail, codes that arent defined in the owners manual). To make a long story short, the company that does their warranty repair, which has worked on the machine approximately 8 times, tells me there is nothing else they can do, the machine is a lemon. But their customer service department refuses to replace it. They say it must be repaired, yet again. But the parts are out of stock (which should be a pretty good indication that theres a problem with product quality). So I am to wait. How long? They dont know. Call again tomorrow.Do NOT buy a Maytag appliance. Customer service does not stand behind their products and the products are no longer up to the quality I had previously expected from Maytag. Additionally, telephone wait times on the customer experience line can exceed an hour and are customarily over 30 minutes. Never had an experience like this with any other major appliance customer service department.

Maytag MVW823OHC SLATE washing machine, $1050 plus warranty $169.95 on 05/27/21 not delivered until 06/25/21, error code on 09/19/21. It is 11/03/21, machine is not working and no part available. Sad.

I just had an astonishing phone call with Maytag customer service (1-800-344-1274). My mind is boggled; my tongue is tied. Only Consumeraffairs.com can offer relief from the bleak, solitary misery engendered by this disorienting encounter. I called Maytag to seek information regarding the number of gallons used by any of the wash cycles of the Maytag BRAVOS series 300 (Model: MVWB450WQ2). I live in California, and like millions of others, Im curious as to what the maximum amount of water used per wash might be. I told the customer service agent that Id be happy with an estimate of any parameter: the maximum water demand for any cycle, the minimum, the average any ballpark estimate would be great! My goal is to change in a meaningful way our weekly water use. How much does it matter if I do my familys laundry once vs. twice per week? Is it any more water-efficient to run one large load vs. two small ones? The Customer Service agents would offer only a scripted response to my query. Could they tell me the minimum or maximum amount of water used (on average) by any of the cycles? Any cycle any condition, just an estimate, please. A universal it depends was all I could extract.The scripted answer? The amount of water used depends on the sensor and the exact conditions. Well, yes, of course; I dont expect a specific amount. Just as the amount of gas used by a car depends on the length of a trip and the speed driven, the amount of water used per cycle will vary, but nevertheless we know, more or less, how much gas is used by a Toyota Camry on a trip between New York and the Maytag Customer Service office in Benton Harbor, Michigan. I noted that, if Maytag claims to build high efficiency (HE) machines, then they must be HE in comparison to something, right? -- otherwise how could they claim that these machines used less water? Less than... what?** insisted that no one at Maytag could tell me the answer. He asked, What reason could Maytag have not to disclose this information? I know this isnt the answer you want to hear, but its simply not available. Not even a range of water use per cycle required/solicited/demanded by the sensor? Can Maytags engineers be so indifferent that they never tested any cycle for its water use, but instead they just imagine that, by virtue of its mysterious sensor, it was lower than the use by their non-efficient machines? Your help in getting to the bottom of what felt like an act of stonewalling would be highly appreciated!

Bravos WL purchased in May 2015. Terrible product. Last week stained 2 shirts beyond repair. Maytag service repairmen stated these machines were poor quality and the only settings that somewhat work are Deep Wash and Bedding. They recommended I buy something other than Maytag. I am not making this up - it was unbelievable. I got Maytag on the phone while the service techs were here so they could hear the comments. The supervisor, Kimberly, said I could not get resolution unless the technician declared it a functional failure. I asked for the definition, as I would assume the basic function of a washing machine is to clean clothes. Still working the steps to resolution, but I believe there is evidence for a class action lawsuit.

I got a Maytag Bravos 18 months ago and liked it at first. After using the washer for a while my towels were falling apart. Did not connect to the washer at first but I began to notice pulled threads on my towels. Talked to Maytag customer service who said they had never heard of the problem. She did say mix the towels with other clothes to prevent the problem. When I got this machine we had about two dozen good quality towels. Now I am down to maybe a half dozen. Those came from the six my Dad bought us for Christmas and I stashed away. The towels have pulled threads all over and will be completely destroyed soon.

Dryer wont dry/ service at dead end. So in 2018 we purchased a Maytag Bravos washer/dryer set. The washer does its job, it washes clothes acceptably. The dryer, which has the sole purpose of drying clothes, DOES NOT dry clothes. It leaves each and every load damp. Two to three cycles are required for even the lightest fabrics to dry. This has been the case since the product was new. After repeated attempts to have the dryer replaced, I am fed up with the whole run around. MORAL OF THE STORY IS DO NOT BUY MAYTAG.

I am in my 24th year of using my Maytag washer and dryer. The set was purchased in 1996, so it has been well worth the money. At this time, it does not spin out as well as it used to, but I just fluff the load and spin it again and then it is ready for the dryer. I have been very pleased with the set and have never had to have a repairman work on them. Cant ask for more than that!

I bought a Maytag washer and dryer about 2 years ago. I’m on my second washing machine (one was replaced from Lowe’s not Maytag). The second washer has now gone out! First it was the lid lock and now who knows! The repairman can’t even fix it. Biggest piece of crap, stay clear!! My first set lasted 25 years. Poor quality workmanship and customer service!!

We updated our 25 years old dishwasher, which ironically still worked, to a Maytag we bought at a BrandsMart in GA in November 2010. Sixteen months later, the unit just died. The panel would light up, but would not run. We contacted Maytag and were assigned a repairman (The Appliance Guy) who could not come to fix the dishwasher until 5 days later. Once he finally showed up, I was informed by him that the control panel for the dishwasher had two shorts in it and it would be cheaper for me to just buy a new dishwasher because the repair to this one would be $344.44. When I contacted the customer service for Maytag, they offered to let me pay for the repairs and then they would give me a six month service warranty for free. Does that make sense to anyone? I could buy a totally different brand, brand-spanking-new and have a twelve month warranty with a better product. I asked to speak with Cheris boss and got to speak with Aaron, who offered me the same spiel. Heavily scripted, I apologize that you are dissatisfied, but all we can do is give you the service warranty for six months after you pay for the repair. I asked him if he was reading a script and he replied no. Now I know that he had probably repeated these same words twenty times a day. Heres a thought, Maytag claims to be a green company, using less electricity and water, and saving the customers money and yet they are filling up all the landfills with these appliances that are not even five years old. How is that being a green company?You know how when you buy a nice new button-up shirt? The makers of that good quality shirt go ahead and sew an extra button on the inside bottom part of the shirt because they know that theres a chance youll lose a button. Well, Im thinking that Maytag should just start shipping a couple extra control panels in every box of Maytag dishwashers. Crazy idea, right? Okay, so an easier and cheaper way for Maytag to correct the problem is to stop making dishwashers. Go back to the drawing board, make the engineer who designed the control panel wash everyones dishes (as punishment and he can get help from the customer service people because theyre really doing nothing), start building the old design dishwasher that has the old switch and dial, and start respecting their customers. There, problems solved!

Maytag WFW7590FW & YWED75HEFW 24 Compact Washer and Dryer: These 2 machines are a lemon and the extended warranty plan was completely disappointed. Both needs maintenance before the 1 year warranty ends. The washer was the worst between the pair. The washer cannot spin the laundry dry. The Home Depot extended warranty plan was not the cost. It takes 2 business day for the service call to call us back. Then a schedule date was 2 days later. The service person complained about not getting authorization to do the work without charging us. He did even showed up for the 3rd call. He did nothing to resolve the issue and said the diagnostics showed there was a load issue, which was not true. A very light load still didnt spin dry. The washer not spinning clothing dry issue has been more than 1 month and is still not resolved. The repair person Dean didnt even re-schedule another date after not showing up today. There is a 90 day policy that we cant request for another repair person to attend to the issue. The dryer also made excessive noise which was caused by a broken attachment that established the drum.

I purchased my 2nd Maytag Neptune washer in 2005 to replace an early Neptune that was complete junk. This one worked OK until this year when it began to make awful noises. After research, I decided it was the bearings that failed. I took the unit apart to get to the bearings and found out the entire outer tub must be replaced not just the bearings, at a cost of $515. What lousy engineering, the bearings dont come out of the housing. No wonder Maytag repairmen are so bored. There is nothing to fix, you just buy a new washer. I wont buy Maytag this time.

I purchased these appliances on 02-10-16 from Home Depot in Loganville Ga., for almost $2000.00. I filed the first repair call less than 3 weeks after delivery. The sensor panel was bad and had to be replaced. Now 8 months later the washer is not starting, AGAIN. The dryer will only dry one load a day or you get the AF code. This means that the dryer cannot push air over 5 or so and we need to have a vent booster fan (an additional $200.00) installed plus have an electrician run a new outlet. I returned to Home Depot with my complaint. Feeling that I have an inferior product, they tried to get Maytag to make it right. Maytag refused to offer any solutions whatsoever. Home Depot refunded a little over $300.00 for my inconvenience.The washer is an absolute ill-conceived piece of junk. It is ROUGH on clothing and does not remove soap. I started out with brand new (expensive) towels when I purchased this machine and 8 months later all of the hems have been snatched off and theyre unraveling and falling apart and are slowly becoming car wash towels.You cannot wash delicates in this machine and allow it to spin. Underwires in bras are badly misshaped or broken completely. You cannot wear them afterwards without being gouged by bent wires. The only way around this is to take away the spin cycle, but you better be ready with a clean garbage can to haul the dripping clothes elsewhere and hung up to drip dry. The washer has NEVER removed all of the soap from bed sheets. I have a dark gray set that show the soap best. Now I have to wash once with soap then wash again with no soap. This negates the machines being efficient.Unfortunately, I found the negative reviews AFTER buying the machine. My complaints are well known to Maytag, seeing has to how the same complaints are found online as far back as 8 years ago. I have been brand loyal for 30+ years to Whirlpool and thought that I was moving up with a Maytag, based on my parents 50 year experience... I was wrong! I will never purchase another Maytag product nor Whirlpool since Whirlpool now owns Maytag. I have researched and am of the opinion that Speed Queen is a far better product and plan to junk this set and replace them with Speed Queen.

We bought a new top of the line Maytag MGD7000XW dryer about 2 years ago. It worked great for about 6 months, thing started acting funny. All of the front console lights stay on all of the time and it ONLY dries on high heat now. This all happened after the warranty period. So fine, I was going to buy a new complete front console (CONSOLE Part Number: W10388467 $300.) as the online repairman suggested. Guess what, Maytag no longer offers the part to fix my dryer. So now I have a 2 year old top of the line P.O.S. MAYTAG dryer that cant be fixed. I will never buy from this company again (Maytag).

I bought a new top loader Maytag washer and dryer on 1/1/16. My first experience with the washer was as many in has stated - It Doesnt Clean, the clothes, also I have trouble with the fact that is there is a string loose, it become worst. Why did they improve a product that did not need improving. They just made it worst. It is totally **. Im stuck with it as I cannot afford another washer. The dryer work fine.

The washer that always needs repair! My first problem with my Maytag washer was that the sensor needed replacing (wont wash or spin). Since then I have had the sensor replaced and motor replaced. Today, I had to call for a service call, and was told that I have to wait over a week! Bad customer service!

Maytag Dishwasher Model # MDB7809AWB2. Part = Console Keypad. We have lived in this home for approximately 4 1/2 years. We purchased a Maytag Dishwasher and had to replace the motherboard in it about 2 months after the warranty ran out. We paid 1/4 of the cost of the dishwasher to get it fixed and I am having the same problem again. I am very dissatisfied with the appliance and I will not pay another $200 to get it fixed. I will never buy another Maytag appliance. Dont buy Maytag!!!

I purchased a Maytag refrigerator back in 2005; right around the time Whirlpool was making a play for Maytag. What a mistake! I had previously owned a GE that lasted 19 years! I even selected a model that did not have any ice in door or water in door that are prone to problems. In the 8 years I owned it, I had a serviceman to my place at least 4 times and dumped around $600 into it! Today the final straw... the compressor went! I will NEVER buy a Maytag again!

I purchased my washing machine in July 2020 and it was broken by November. It took months without a washer before the warranty finally replaced my machine. I had the second machine less than 6 months when the water pump went out on it. They told me it would be two weeks for the repairman to come out. In the meantime my clothes were locked in the washer half full of dirty water. They told me we would have to force the lock to retrieve the clothes so they would not mold. The repairman called, never showed up, just called to ask what was wrong. Told me he would order parts and I had to wait 21 days to see if they would be able to find them. Today is day 21. I called the warranty back and was told it would be escalated and someone would call me in 4 days with a resolution. In the meantime I have spent $60 a week doing laundry for my family of 6 at the laundromat for MONTHS. Out of the 18 months have dealt with Maytag, I have spent more than 6 months at the laundromat. When I asked to be reimbursed the money I have spent they offered me a free 6 month extended warranty or a fifty dollar gift card. This product is garbage! The customer service is garbage. Dont waste your money.

Purchased the Maytag Bravos XL washer and dryer in January, 2014. Today, 5/16/15 (less than 1 1/2 years later) the repairman tells me that the cause of the loud noise in the spin cycle is bad bearings. Only a 1-year warranty on the machine. I have never purchased extended warranties on appliances so this will cost me $400! Or a new washer since this is more than half the cost of the new washer. This is bad business, Maytag. Ive been a loyal Maytag customer for years but I think Im heading to Speed Queen with their 5-year warranty unless youre going to give me a helluva deal to keep me. Grrrrrrr.

Purchased this dishwasher 3 1/2 yrs. ago. Control panel went out. We would have had to pay almost the cost of new one to replace the part! Maytag used to be reliable. The dishwasher we owned previously (not Maytag) was still working after 12 years!

I purchased a Maytag dishwasher with a control panel in September of 2013. In August of 2014, the control panel died and did not allow me to run the washer. In March of 2015, the piece which was replaced died. When contacting Maytag, even when they did the repair the first time, said they were unable to cover the cost because it was now out of warranty. Ive seen several class action lawsuits around the product with Maytag. Do not buy a Maytag. It used to be a quality brand, but is now terrible.

We have had this refrigerator, model MFI2665XEM7, less than two years. The ice maker stopped working and we had it replaced at least 6 times in a two month period. We had a solid ice sheet in the bottom of the freezer drawer and it leaks water on the floor constantly! Even today... after another ice maker replacement, we have no ice! I never wanted a Maytag, but finances and the small space we had gave us little choice. I am not sure what our next move is. I will NEVER buy a Maytag product again! I should have google this sooner and we could have saved the poor repairman all of those trips!

After only 4 years, this washer stopped spinning. Called Maytag support (Ha! the ads show the Maytag repairman sitting by a non-ringing phone) I had to wait 20 mins to get through. Only after paying for a service call would they be able to determine if this problem was motor-related. In reading reviews (which in hindsight I wish I would have done prior to purchasing) this is a common problem and is related to bearings going bad. Pay for service call vs buying a non-Maytag product -- will set this out by the curb and buy a different brand.

Bought used and still performs like a champ. It's old. Have the matching dryer but that quit working some time ago so I hang dry clothes.

I purchased a Maytag stainless steel French door model the middle of 2006. While cleaning the French doors with the cleaning product given to me with the purchase of the new fridge, I notice what looked like coffee on the doors. It wasnt, it was rust on the stainless steel doors. I called the service tech and they came out. Rubbing the fridge, he told me it wasnt rust. He took a closer look and found that it was in fact rust. He called his office; they told him that rusting on the doors has been an issue lately. He charged me $65.00 for what I already knew. I called Maytag and it took a while, but they decided to send new doors. However, I had to have a Maytag rep install it, which would cost me. I didnt have it done. Two years later in 2010, the French doors felt hot to the touch and the inside was warm and not cooling. The freezer was fine. I called for a tech to come out and it’s another $65.00 to fix a fan motor that blows cool air from the bottom to the top. Oh, it’s not under warranty because it wasnt inside with the motor. Total cost: $235.00. In 2010, I woke up and opened the fridge to get milk out. It was warm and so was the inside of the fridge. I thought it was the same problem, but the freezer also was warm. Upset and not wanting to pay for this again, I unplugged the thing and started using a little fridge that I have stored in the basement. It has no freezer. Today, I finally got over being pissed and decided that I would have a tech come out and find out and finally fix it. The tech said that the compressor has failed and it would cost $790.00 to fix. Im not having it fixed, so it’s another $65.00 gone. The tech said that the compressor in Maytags/Whirlpools has been a pretty big issue lately. All I can say is that I will not ever purchase Whirlpool products again. From inside to the outside, this product has been unsatisfactory. I just noticed that the rubber is failing on one of the French doors. Wake up, Whirlpool. Model number is MFD2561HES.

Maytag dishwasher, MDB4651AWW was purchased on 15/02/2010. Touch panel was replaced under warranty on 16/08/2010. Touch panel became defective on 04/07/2012. It was $103 for the service call: panel was not replaced (too costly, > $200). My 2-year old dishwasher is now useless. The touch panel on this model has failed twice in two years and is obviously a design failure. I would ask for a free replacement panel.

Purchased a stackable washer and dryer (Maytag) for our new condo in Feb 2015. After it was installed a few months later the problems began. The washer wasnt removing the water from the clothes. We contacted Maytag and they informed us that they subcontract out to a company called Appliance Service of Central Florida (727-462-0394). Contacted Appliance Service and set up a date to be serviced. Since then, we have had Appliance Service out to our place over 8 times. They found fault in our control panel, our door lock, replaced our motor and have replace several other parts. It has been over 4 months since they started repairs on our machine and have informed me that they have a right to try and fix the problem. I have no problem with this but when and how long do I have to put up with this? They dont seem to care that my wife and I havent had a working washer in over 4 months.The people doing the repairs stated that this machine should have been replaced because it had or has several problems with it and after replacing the motor, electric panel etc it still isnt working. When I contacted Maytag they stated that as long as Appliance Service is working on the problem, it out of their hands. Is there anything I can do besides contacting a lawyer and spending more money?

Water ran out of washer and flooded my garage. 1) Replace computer. 2) Wrong computer. 3) Water still flooding garage. 4) May need water valve. 5) Showed up didnt know what to do, then left. 6) Whole new tub - 3 hour repair - 2 weeks until they have time to repair. Still waiting. HELP.

After only 2 years my microwave stopped working. Now I can purchase a new warranty which is just as much as a new microwave, have somebody come out and fix it, or pay a service charge which is just under $100 and does not include labor and parts. I figured out now why nobody calls the Maytag repairman. We cant afford it!

I’m so disappointed in this refrigerator! It does not keep a steady temperature. It’s only 3 years old and will not buy another Maytag. I do like the freezer on the bottom but it also does not keep a steady temperature.

I purchased Maytag washer, as it was rated the best of the best at the store. First of all, Delicates cycle washes exactly like Normal. All my sweaters got ruined as the agitation is VERY HARD. I dont think the manufacture even knows what that cycle means! Absolutely awful! Theres no difference between Delicates and any other cycle!Second, Deep fill cycle. If you select off on that cycle the clothes get hardly damp. HOW can you wash hardly damp clothes???? If you go with Deep fill, the washer is supposed to weigh your laundry 1st and ONLY pour the water according to the weight. Well.... you can put only 5 small items and the washer fills all the way to the top! What the hell is this???? How can few items fill such a ginormous washer???? It doesnt work! Im so pissed and want this washer out of my laundry room!

I bought a Maytag dishwasher from Home Depot in February 2012, $700. After a few months, the buttons stopped working and the machine was unresponsive. I called Home Depot and they fixed it under the warranty. This continued to happen every 2-3 months. After a year of dealing with this, the warranty expired and I had to purchase the manufacturer extended warranty with Maytag, $240 for 5-years of coverage. The problem continued, and every few months, the thing would stop working and I would have to call for service - 2 to 4 weeks without a dishwasher waiting for service appointment then parts and another appointment for the repair.Perhaps my machine was just a lemon. I dont think they make that model anymore. Heres the number so that you can avoid a three year headache of a machine, MD87749 AWM2. I will say that after MANY agonizing phone calls with warranty company, after 2 years of ongoing service calls, they eventually issued me a check to replace my lemon.

I bought my Maytag washer thinking that I was buying a quality product. My washer hardly ever can complete a spin cycle without bumping and knocking and then stopping. I have to babysit this washer because we never know if it will complete a cycle or not. The machine is totally level. We have to adjust almost every load just to wash clothes. Sorry Maytag but this washer is crap and I will never buy anything made by Maytag. What a waste of my money.

Well Maytag, shame on you! I just called customer service about the third repair made on my Maytag 4000 Series Washing Machine; its only two years old. The rep side stepped the limited warranty that is good for five years on the motor and tried to sell me another warranty for $329.00. I have $460.00 (parts only) in repairs. Purchasing a warranty will have me spending more money than I actually paid for it. The excuse that I was given was (per quote) our machines are made by people and we have no way of determining the outcome of our products past the given warranty. Maybe you should have considered buying the extended warranty that was offered at the time of purchase. Yeah, maybe I should have, but Maytag should build a product that consumers are happy with, and extended warranty sales past a longer period of time might make more sense. If you are thinking about purchasing any Maytag appliance, I would think twice or you just might get some person on the other end of the line that just doesnt care, representing the name of Maytag! I visit the Big Box Stores daily and you can bet your tail that I will make a special visit to the appliance section just to discourage any one from making the same mistake I did! Just think, the last washing machine that I purchased lasted for 9 years (not one issue) and it was still working when I gave it to someone in need! I have three appliances in my kitchen that are 11 years old, never had one problem with either one. Thank You KitchenAid! I should have purchased your washer and dryers!

This washer is the WORST washer we have ever owned. I should have returned it when I attempted and Lowes talked me into keeping, stating I was just overfilling. I put only a few items and the jeans came out with dirt still all over them!! I have photos. Pathetic. Not enough water, not enough agitation. DO NOT waste your money!

Maytag dryer MEDC215EW - This dryer does not dry the clothes without many wrinkles. Sheets just ball up with the inner sheet a mass of wrinkles. Small loads just flop from top to the bottom of the dryer, falling in clumps. I have gone back to having to ironing. Very disturbing!!! I would not recommend this dryer to anyone.

I bought a Maytag dishwasher in 2019 in Home Depot for my new home. The dishwasher stopped washing dishes after two years and 6 months. The price of the new machine was 700$ and I did not buy the extended warranty. The trouble is circulation pump, that cost to install the new one from local service would be about 350$ plus the new pump 150$. I consider quality is very poor if the new dishwasher works only two years and then it is better to buy a new item than fix the old one. Never never buy Maytag production.

I bought this washer three years ago. It is the worst washer I have ever owned. Washing a load of clothes, it goes off balance constantly, large load, small load...it doesnt matter. The smell because of low water usage is awful, and the clothes dont come out clean. I have to buy a new one and that really stinks. Maytag youre off my list for purchases. These days its quality that will keep you in business. We are too smart for this garbage.

We purchased a new Maytag dishwasher for $500 from Home Depot about 1 year ago... it stopped working 4 days ago. I did not get satisfaction from Maytag customer service as they tried to sell me a repair program whilst I was trying to determine if it was under warranty as it is a known problem. I now have a repair person coming out with a price of $189.95 + time. A complete joke of an organization. Lesson? Do NOT purchase any MAYTAG brand. They DO NOT stand by their product. My rating is ZERO STARS, the site forces me to enter a star which is ONE TOO MANY. I will NOT do business with Maytag, Whirpool or any of their brands again.

I purchased this dishwasher from Sears in July of 2013. Barely 3 years ago. The last few months the controls have been acting odd. The control lock would automatically just turn on at odd times. Yesterday when I hit normal cycle it went to a different cycle and had many other options lit. It would not start. Finally it went dark, no lights, no nothing. I see many people have had these types of issues with this type of Maytag dishwasher. Disappointing. A dishwasher should last longer than 3 years. Sears said they would send a repairman out but it would have been minimum $200 after it was all said and done. Id rather own a non-Maytag dishwasher so we went and bought a different brand.

Bought a Maytag dishwasher model MDB7749AWM2 on 02 Jan 2012 with no issues whatsoever until three days ago when it stopped working altogether and after doing a series of tests I discovered that Im joining a large and growing list of owners with the same problem. I never have been a fan of digital controls due to their vulnerability to temperature and humidity conditions or high impacts for that matter. Ive owned many dishwashers of various brands for upwards of 10 years on average each. This is the first one not equipped with analog/mechanical controls. Im hoping I can still find more of that type.

I purchased my Bravos (ecoconserve) washing machine in 8/2013 from hhgreg. The problem I have is this grinding noise with the spin cycle. So I unplug the machine because the lock lid light is flashing and wont unlock unless I unplug the machine. I grew up on Maytag so that was the reason I purchased this machine but never again. I am so disappointed in this product. :(

The machine does not rinse soap off clothes even after using 2nd rinse cycle. You have to wash clothes again using no soap at all. Defective machine maytag does not help or Clare wanted to charge service fee for tech even though machine is under warranty. This washer should be recalled. Very bad product. Lots of complaints.

We have a Maytag drying center that is almost 6 years old. It never did a good job drying especially for the money we paid, but it just quit on us two weeks ago. We purchased it from TA Appliances in Barrie, Ontario who recommended that we call B&K Appliance repair to fix it. The owner showed up and said he would be back to us in a few days to fix it, as soon as part arrives. He now wont return calls and it has been two weeks, so we called Maytag customer service. We knew we were in trouble when we received a message telling us Due to higher than normal call volume... (so much for the Maytags that never need repair). Anyway, we finally reached an incompetent, ignorant and anti-customer service representative who proceeded to tell us in an extremely, nasally drawl that the part needed to fix our 6 years old dryer is no longer available and the most they could offer as compensation for this on our $1500 plus tax dryer that should last at least 10 years is $120. This is for a dryer we never used more than 5 times a week.

Do not buy this refrigerator!! It’s small on the inside but to top it off the vent is on the left side, not in the back, so everything freezes on the left side of the refrigerator. Plus they positioned the light right in the front at the top so you cannot put a gallon of milk or anything tall. Not orange juice, apple juice, nothing!! Horrible design. I’ve had the repairman out, he said he couldn’t do anything about the freezing on the left side unless he turned the temperature up on the fridge and on the freezer. We tried that & The ice cream was so soft, almost melted. The problem then was the temperature was too warm for milk and other items. Not a recommended temperature to keep cold items. He said I would have to keep everything away from the back & the left side to use it without freezing my items. I’ve lost a lot of food because of this. Very unhappy with this refrigerator!!

I bought my Maytag Model LA608 washer in 1976. It has very few electronics and a mechanical timer. It has been used every week since then for 2 or 3 people. It has had 3 problems in its lifetime. I replaced the 2 valves that control the hot and cold water entering the machine. I replaced a small plastic sprayer part. And last year I replaced 3 clamps that rusted and started to leak. Thats it in 40 years. I was able to open up the front and back covers to get at the parts quite easily.It is a simple machine with almost no electronics to stop working. Nothing bothers me about the machine. Its simple and wonderful. When it finally breaks, I will try and find a good sized machine that washes permanent press and regular clothes, has a controller to select hot/cold/warm water temperatures, has a regular and gentle cycle, and has 3 load levels for the water to be used. I will try to find one that is good quality with few electronic parts. I will not buy a high efficiency model that uses less water as I am on a well and water shortage is not a problem where I live. I will not buy a front loading model.I would not buy a machine that has options that I do not need. I would hope to find a quality machine similar to what I have now. I would read as many ratings about the various models before making a selection and then I would cross my fingers and hope for the best. If it is possible, try and find a good quality machine that will be dependable over time. Buy a basic machine with only the options that you really need. There will be fewer parts to stop working.

Bought the washer in February 2012 for $900 at a local appliance store, delivery included. Just yesterday (10/16/15) a 5 cent piece of grey plastic flew out of the lid lock mechanism. Thinking this $900 modern piece of machinery painstakingly designed by intelligent people with university degrees would certainly work if I just stuck the plastic part back in. I just popped it back in, the lid locked, and the machine spun away happily (only having to run a correct cycle for an unbalanced load twice! What joy!) Fast forward 40 minutes, I skip down the stairs to go retrieve my flannel sheets (because its October in Pennsylvania, its getting freezing cold at night) and pull up gently to open the lid. It doesnt budge. About 2 hours later, following a screaming match and some furious googling, it was determined we would need two people to pop the entire top off the machine to extract my sheets.So in order to use the washer to clean clothing now, weve been unplugging the machine. Removing the three screws on the control panel (aka brainbox), unplugging the black and white wire from the brain box, taking the control panel off and sitting it on the dryer, and using putty knives to push in the metal clips holding down the top of the machine down, and prying the entire top of the machine back on its hinge. Then I can get my clothes out. Then doing so in reverse (dont forget to add detergent before shutting the lid! It will lock and you will have to pop the entire top off again.) to use the washer. All because of a 5 cent piece of PLASTIC. What brainchild figured, Eh, we can just use plastic for this important piece that the washer wont run properly without. It doesnt matter!? Someone that wanted to make $300 a pop doing service calls thats who.I cant believe Maytag has gone so far down the tubes. In case anyone else ran into this problem and needs to fix it, write down the model number, serial number, and other crud listed under the lid. Then use them to wipe while youre in the bathroom. All you need is the company and part number on the lid lock mechanism. According to Maytags website my washer doesnt exist. And there was no way, no matter how creatively I googled, to find a part for it with the Maytag model number. So now I have to try to find this measly mechanism to replace and try to use this piece of crud for a few more months. I guess my Christmas present this year is buying a new washer. And you can BET it will not be a Maytag.And two more things: with no agitator, you can fit really big stuff, but you also get to hear your washing machine dancing on your basement floor with an uneven load. No matter how many times you try to re-position items, it runs a corrective cycle, refills with water, and spins everything into a ball AGAIN. Also, the miserable thing is starting to rust. Right on the sides and near the lid hinge, and all around the bleach receptacle. How cheap, a washer on which the paint rusts right off with chlorine bleach.I wish I still had my Grandpas old 1930s wringer Maytag. At least I knew that one would work without a cheap piece of plastic. And at this point I might prefer wringing my clothes to hearing my washer try to escape. In short: cheap parts, no replacements available through company for DIY repairmen, company designed to force customers to use their servicing for $300 a pop. 1/10 would NOT recommend Maytag.

On 11-10-10 I purchased a top of the line Maytag fridge. All had been great till we needed a part in Nov. of 2014! After nearly 3 months of searching they tell us that they no longer make parts for this unit and I am out of luck! Fridge works great but the center seal is broken (french door - Mullin) they quit making the part???? I am beyond angry! Will never buy Maytag again!!!

I purchased a Maytag Bravo Washer in October of 2011, I had a repair man come to check it since the spin cycle sounds like a jet is revving its engines in the laundry room. He told me that the repair cost is $493.50 to replace the transmission. The machine also has problems with the circuit board. The lid lock goes on and off and on and off so you cannot run the machine. Speaking to Maytag they just kept saying your warranty is over and we dont offer any assistance on the repairs. The machine cost $530.00 in 2011 and they think its reasonable to have repairs more than the cost of a new washer. They said they had no complaints on the model. My repairman advised not to buy Bravo, Cabrio or Calypso models since they all have the same problem with the transmission and electronics. I think they should at least pay for the parts, the transmission is $300. And we didnt even price the electronic part of repair.

Bought a MDB7601AWW, and then replaced front panel to stainless. Configuration options are great (can’t find better at cost up to $1,200.00)! I haven’t had an issue with any stains on non-stainless tub. Problem is now control panel failing for second time. After 1st time, sealed all connections in silicone to prevent steam from affecting it, as recommended on DIY video. I just replaced the door latch, thinking that may solve it, but hard to troubleshoot without any indicator lights. This second failure (2 yrs later) shows no indication that steam or water caused it. It does start now, stuck on heavy wash, heated dry, sanitize - per top lights. Front lights totally out. Debating whether to buy a new dishwasher ($$$) and give up super config (hard to find fold-down tines and fold-down small shelves on upper and lower racks, clips for small items, and basket that can be changed, placed anywhere) or spend at least $162 for the panel AGAIN and hope I get another 2 years from that while trusting that some other element doesn’t go out. I believe Maytag should, at minimum, make the panel reasonably priced by offering a rebate, since the part is not sold directly through them. Obviously this problem is a design flaw. I am the only one in the house, so the dishwasher is not under heavy use. At least I found how to replace it myself on YouTube, though it requires the door to be completely taken apart and would be easier with an extra set of hands and a younger back. Hard decision since it seems newer, expensive appliances have problems as well. If I buy new, I will not hesitate to get an extended warranty (1st time ever).

We have had washer/dryer Bravo Series and been nothing but horror stories. Washer bounces all over room to point hoses come out and flooded my laundry room and foyer and garage. It takes over 1hour 45 minutes to do loads sheets which is 2 sheets 2 pillowcases. The repair man told me that takes that long due to MY sheets are dirty. I have been married 46 years and never heard that ever!!! The dryer is just as bad, takes over hour and half to dry sheets and towels almost 2 hours to dry. DO NOT BUY MAYTAG ANYTHING. The person who said needed hurricane straps to hold washer is something I agree with. Just a horror.

I ordered my dream refrigerator (Maytag Model MFT2776FEZ) on 05-12-2017. I had to wait 4 weeks for it to arrive because it was on back-order. I was willing to wait. All was good for 6 months. January 2018, the six month old refrigerator quit cooling. It took 2 1/2 from the service call until the part came in to fix before I could use my refrigerator again. I lost all my food. The same thing happened again in March 2018 except that it took 4 weeks for the part to come in once the serviceman ordered it. I lost all my food for a second time. February 2019, the same thing happened again. I placed the service call on 01-31-2019 for service, but the tech could not come out until 2/6/19. The part had to be ordered and could not be installed until 2-28-2019. For the 3rd time, Ive lost my food. My best friend that has appliances that are nearly 30 years old. She was going to replace all of hers and get exactly what I ordered. She has changed her mind and has decided she would rather keep her outdated appliances because they work.

I like my fridge. Its a old one and still works. Its been very reliable and have never had a problem with. I dont think I would ever purchase a different brand for Maytag is the brand for me. They last for years.

I bought this electric dryer Bravos (Model# MEDB850YW0) in Nov. 2011. Since I bought it, its giving me the same problem - it doesnt want to turn on. Today is the 6th time that I have been calling the customer service to fix it. Yesterday, it just got fixed; and today, its not working again for the same problem. I asked them if they can give me a new one, since its not even over 1 year. But they said they will not replace it because it cant be fixed. But it is so ridiculous, and its wasting my time. This is so unfair. I paid $800.00 for this machine.

I bought my black refrigerator in 2006. It has ice in the door and freezer on left side and refrigerator on right. I have not had any problem with my refrigerator and it continues to serve me well. When I need to buy another one, I will probably get a stainless that doesnt show handprints.

Our new washing machine (Maytag Maxima XTLM Front Load Steam Washer & Dryer w/ Pedestals) has developed a loud knocking while running which the authorized whirlpool repair provider said was due to internal ball bearings. He said that the washing machine caused the pedestal to become warped and the only way to stop the knocking was to replace the pedestal. Whirlpool refuses to replace the pedestal saying that the pedestal must have come that way or was installed incorrectly or was overloaded. There are only two of us and we never overloaded at all. The knocking started several months after the installation. If the pedestal was defective (came that way), why wont Whirlpool replace it under their warranty?

We purchased both a new Maytag washer & dryer in 2011. Our dryer, Model #7000XG1 all of the sudden started thumping when we were drying our laundry. After we called a technician to come out, he stated we had a crack in our drum. How in the heck does that happen in 4 years time and only laundering for 2 people? Of course this steel drum should not wear out before the other parts, but it did. Since there is a backorder on the replacement drum, it makes you wonder if this problem is wider than it seems. Also, Maytag would do nothing for us other than offer us the purchase of a new dryer at a discounted rate good for only 7 days of their offer. Seriously, how about standing behind your product? And, then again, why would we be enticed to spend that kind of money on the same type of product that has flaws? Uh, duh Maytag or Whirlpool. Silly fools you are.

My refrigerator is several years old, and I would buy the same brand when I need a new one, although I would hopefully buy a counter depth one because my kitchen is so small, and the one I have now is kind of big for the space.

Maytag used to have a reputation for quality. Their low water energy efficient Centennial is a waste of money. Half of the time clothes come out wet and most of the time they are still dirty. Also you are only supposed fill the tub 1/4 of the way with clothes so you end up doing 3 times as many loads per week. What genius came up with this idea? Save your money. You would get better results washing your clothes in a tub with a washboard. Seriously!

I have had the set of Maytag Bravos for about 5 years now. In the 3rd year, the bearings went out. Just recently, leaking water pump. This washer easily eats clothing. I have to disassemble every so often just to get the missing socks etc. out. The only good thing, Maytag should be ashamed I know this, is that the machine is easy to fix. I imagine since they made it so cheaply. Really nothing to the machine.

I purchased a Maytag (as Maytag was always rated the Best) and from the start was not happy with the product. I contacted Maytag (Whirlpool, the makers of Maytag) and was told to get stains out, you had to pre-soak and scrub the area... really? Then I might as well just hand wash all of my clothes and hang to dry. I would not need a washer. My clothes do not come clean at all. DO NOT PURCHASE A MAYTAG (or I think any washer Whirlpool makes as they do not back their products).Prior to this, I had a Whirlpool washer with agitator and loved the washer. Clothes were always clean, and I did not have to pre-soak stains for them to come clean. Go Figure! I have never been so disappointed in a washer or company. I am now looking to purchase a new washer as I have had it with this one... and it wont be a product made by Whirlpool.

Bought refrigerator 2012 from Home Depot (model something like MBF1953YEB - how sad is it that I now have this number memorized?). Freezer too cold, refrigerator way too warm. Freezer air ducts frozen over. Tried manual defrosting twice per YouTube suggestions. Finally got repair for $400!!! Thats about half what I paid for it! One proponent repairman stopped me mid-sentence when I said Maytag saying, I know what it is. The computer (Jazz?) board needed to be replaced for $217. I just looked up Maytag to see it was bought in 2006 by Whirlpool. So I wont be purchasing any more Maytag or Whirlpool appliances.

Bought a new Bravo washer and gas dryer; Dryer model mgdb980bg. Bought it September 2013. I have had nothing but problems. The dryer would run for 10 minutes then shut off saying check lint trap. Then once it started going again, it close were even damp. It wouldnt sense so it wouldnt start. Finally it got to the point where I couldnt get my dryer working so I phone repair place. The guy came out and set the temperature. Gauges or sensors were off by over 20 degrees as well our entire starter motor was shot. That was over a month ago and we are still waiting for a part that is apparently back ordered. I call today and they said its a faulty dryer and it could take anywhere from a week to two months to get the part. I am requesting a new dryer.

I have to rewash many load of dark clothing because pale white smears appear on the clothing most times. Ive tried various cleaning methods to try to remove any residue that might be in the walls of the tub. Unfortunately, I cant afford to replace the Maytag white elephant model 500XWZ, serial C31430894. I no longer have the receipt. Buyer, beware. No Maytags in my future.

I bought a every expensive Maytag Neptune (washer and dryer one unit) and it is now sitting in the carport. The washer broke and I had to have service people come to my house continuously. Over a period of 6 months I had to pay for 3 motor control boards plus service calls. Thats when I had I moved to the carport. In 2012 I bought a Whirlpool Duet washer and dryer so I would be able to stack them. I had to put them at Sears because I had to use layaway. I paid for them over 12 weeks and had to use a laundromat during that time. Last week I got a F01 E02 error code which means replace motor control board. These boards cost over $300 each not counting the cost to install it.I did talk to Sears since the washer was only bought 4 years ago. They were nice to me but could do anything for me. Truly sad when a washer only lasts 4 years for the amount of money I had to pay to purchase it. I dont know what I going to do now since I am now retired but I WILL NEVER BUY A WHIRLPOOL OR MAYTAG AGAIN.

MDBH979SAM0 - Bought this dishwasher from Home Depot 2 years ago and have taken care of it, never abused it or anything. All of a sudden it just starts freaking out, once you start a cycle it will wash and then rewash and then keep going costing us money on electricity, water and wear and tear on the machine. Ive tried everything but it seems like its just stuck in start mode. The indicator lights on the panel flip out too, they will all blink randomly. So when I close the dishwasher and dont intend to start any cycles and it is off it will start up all on its own so Ive had to unplug it. Funny how I called to order a control panel part and its on back order... Very interesting how they are out of this part probably because everyones ordering it.

Well I must say I concur with all previous posts. I just replaced my Bravos with a Samsung after my jet plane of a washer died. My repair guy said it was not worth it to fix it. I had already replaced the shocks two years ago but I did have mine for 8 years. I have had the same problems as previous posts - rust, smell, holes, broken, too expensive! Hello to Samsung!!

I bought this machine in 2013 and within a year it had stopped going through any cycle. It turns off and I either have to restart a cycle or set the machine to rinse/spin. My clothes do not seem clean so I have begun handwashing them before putting them in the machine. I retrieve clothes and find some clothes dry. My towels have worn spots and threads pulled out. I cannot wait till I get a new washer because I am going to put this Maytag Bravos in the backyard and take a baseball bat to this hunk of junk.

I purchased Maytag Washer and Dryer 3-4 years ago, upgraded to the premium washer and dryer, SS drums and have been dissatisfied from the start. The washer was extremely noisy; we were told this was normal. The dryer began making strange noises just outside the warranty period, and the belt and pulley had to be replaced. I was shocked at the cheapness of the pulley design, but the replacement part was of better quality. The washer began making a horrendous squeak shortly afterwards, again, outside the warranty period. The repairman said that they were all like that, Maytag used inferior transmissions and that it would be cheaper to replace the washer than repairing it. My mother had the same experience with a similar model. Needless to say, I will never purchase another Maytag product. FYI, there are only three people in our household, all adults, light duty use.

The circuit board on my seven year old Maytag French door refrigerator died. I called a repair company out to see if it could be repaired. He went to order the part and said that it was not available. Now I read a review from someone else saying that Maytag does not have parts for appliances that are over 6 years old. Thats ridiculous that after spending so much money on an appliance that parts are not available. I will never buy another Maytag appliance.

Same problems as everyone else. Water not soaking the clothes, questionable load capacity, shaky (we have engineers in the house so there is no way they did not look for floor evenness as the stores/Maytag will tell you that you may not have done, complete bs) etc. Its absolutely horrible that were all now stuck with such a terrible machine. I really wish I had read these reviews before (I googled the machine earlier but got generic stuff and didnt stumble upon these reviews until much later). Maytag should take responsibility on this as retail stores do not take back appliances unless they are defective. The Bravos is definitely a defective product from the get-go though.

Please let me know if there is a class action suit. This refrigerator leaks water all my floor every three days or so. I have to chip the ice off the bottom of freezer every three or four days. Storage is also a joke. Poor design.

I purchased a Maytag dishwasher on Oct. 12, 2013. The control panel failed in July 2013 and had to be replaced. I was unable to program a wash cycle and the lights would move all around the front. After the first failure, I was told that the control panel would only be covered for 3 months - the original purchase date for the washer, NOT the date of the NEW control panel. I was then talked into an extended service plan. Now, four months later, the control panel has failed again and I am unable to program a normal wash. A repair man is not scheduled to come for another 9 days. As a single homeowner, this product is not used even on a daily basis. I will never purchase another Maytag washer. They do not back their product with appropriate repairs.

I have a Maytag dishwasher model mdb6759aws3. The control touch pad broke after 1.5 years of light use. It costs $475 to fix (includes labor). Completely unacceptable service provided by Maytag over the phone. The only concession offered was a 25% discount if I bought the replacement part (control touch pad) from them. After some internet research, I learned Maytag marks up their parts prices over 25% so they are really not giving you a discount at all.I filed a complaint with Maytag but they were unable to provide me with any evidence of doing such except for an 11-digit code. Due to a major defect, Maytag should have sent me the replacement part for free. I told Maytag I thought this was fair and that I would pay for the labor. I will never buy another Maytag appliance again! They are junk and the company does not practice common sense customer service.

Maytag Dishwasher model #MDB7759SAW3 continues the Whirlpool company legacy of subpar control panels in all of their dishwashers. It is telling that they have been allowed to market the exact same failing parts for well over a decade without any accountability. They had one recall circa 2007-2010 and pushed customers into purchasing the model I have which suffers from the exact same control panel design.To further frustrate the consumer experience, Maytag customer service reps and supervisors allege that they have never heard of a customer having issues with their dishwasher control panel before. The panel beeps endlessly and refuses user input regardless of whether the door is opened or closed. After a power disconnect it will reset and sometimes allow one load to be washed before resuming the non stop beeping. If opened and closed during the beeping it will cycle through a completely new wash cycle on its own and resume beeping. Maytag customer service response this morning was, “thank you for being a Maytag customer”.We will my be purchasing their replacement control panels as they are of poor quality and it is well documented that the new ones fail annually as well. These are “high end” appliances and are not inexpensive. We will simply cease to use whirlpool, Maytag, Kenmore, Kitchenaid, etc. brands in our home and will advise everyone we know to protect themselves the same way.

As others have stated, cant wash more than a couple towels or 2 pair of blue jeans. The washer is useless. Purchased Maytag for quality and received crappy worthless machine. Maytag should take returns and refund buyers money!

Since day one, no matter the size of the load or how careful I place the clothes or what level or water, washer vibrates and moves around the floor. I have had service out twice to recheck level but it still vibrates. Worst washer ever. I should have spent the money to repair my 20-year-old Kenmore.

We purchased our washer and dryer set in December of 2010 and had it for about 2 years with the extended warranty...needless to say around 1 1/2 - 2 years the metal around our bleach dispenser started rusting. Maytag considers this cosmetic! I am shocked to think that its cosmetic...on the outside of the washer yes, but on the inside no! It is faulty on Maytags part. I have spoken with Maytag and they tell me if it doesnt happen within the first 30 days there is nothing they can do. So I will tell anyone and everyone what was said to me via Maytags own repairman, Buy cheaper washers as NO ONE offers an extended warranty on the inside of the washer rusting. Whirlpool is the owner of Maytag now so beware of Whirlpool as well. Check out the warranties and make sure you will be covered longer than 30 days for rusting on any washer you intend on purchasing. We learned the hard way and well....we will be buying a cheap washer like the repairman suggested when this one goes out.

I had purchased a brand new Maytag refrigerator and in less than a year, the ice dispenser stopped working. I had called Maytag warranty department in regards to this matter and they flat out said, There is nothing we can do about it. I will never deal with this company whatsoever and wouldnt recommend it to anyone about it. Less than a year and they refuse to fix the item they sold. No better than a used car lot attitude.

I absolutely do not like the fact that you can’t choose what size load you have. The washer wants to do it for you but it is not very good at it. You have to fool the washer to get any kind of water level or just use the deep fill every time which is what I do in order to get the clothes clean! This defeats the whole purpose of trying to save water. Also there are too many settings. I mean we’re just washing clothes here not flying a jet. I personally would prefer dials instead of the digital instrument panel. So much easier.

Dishwasher (MDB7709AWB2) stopped running mid-cycle, internet search revealed that control panel needs replacement at a cost of $135. excluding labor, for a dishwasher that originally cost $348. Notified Maytag and am awaiting a response.

I was pleasantly surprised that this basic model would work so great! It really gets the dishes clean. It came with the house so I did not choose it and probably would not have bought it if I had to shop for it.

We bought this washer in 2009. It has only been 5 years and we had a problem with the lid, now it leaks on the floor and most of all it has been rusting on the lid, the sides and rusting around the bleach port. Rusting on the top edge of the outside metal skin. I am not happy with this product at all. The serial number CV0870202. Model number is MVWB800VQZ. It is a quiet series purchased on 2009. I am not happy with the quality of this washer and I will not buy another Maytag.

I bought a Maytag Commercial Technology Washer and a Bravos XL MCT Maytag Commercial Technology Dryer in July 2018. On April 14, 2020 the control board went out and Maytag will not replace it. It’s going to cost $463.00 to get it repaired. I do not like this washer because it does not fill with enough water to get my clothes clean even with the deep fill cycle turned on. My clothes still smell nasty after they are dried with scented dry sheets. I will never buy another Maytag product, because they are cheap made. Maytag advertises as American made. Fact is they are assembled in America but the parts come from China and Thailand.

These are the issues, Water level is ridiculous, clothes often have dry spots, I use only the high water level which is a joke. The tub bottom is very hard to reach because it is too deep even for a man with a long reach. The tub itself is about 16” deep but never fills more than 4” of water on the high water setting. Why such a deep wide tub when you can only put 4” of water? Cleaning is poor, the machine is very noisy, very. The worst machines we have ever purchased with ridiculous sensors, bells and whistles. The dryer takes forever to dry clothes and again the sensors are a joke. The high efficiency of the units means you work much longer for clothes that are wrinkled, spotted, less clean looking and sometimes damaged. Where is the savings? And don’t say hydro and water as the washer cleaner cost, wipes that out and more. We gave our 26 year old machines to Habitat, neither machine was ever serviced and were in perfect condition, they were Maytag. They have destroyed their name. So sorry we decided to modernize our laundry room.

Purchased this unit back in November 2011. Sometime this year it started leaking water just like many others from the freezer unit onto the floor (many times large puddles). Im tired of the permanent towel on the floor to absorb the water to prevent a potential slipping hazard. I too went online and found a very nice video on youtube which showed how to disassemble the freezer compartment. Took everything apart and noticed that there was water frozen on the supply line. Melted this and put everything back together, for about a week there was no water leaking so I figured all was well. About a week later the puddle was back so I sent an inquiry to Maytag and let them know I had an image of the issue and asked if it was covered through manufacture warranty. Here is their response: Your email is extremely important to us here at the Customer experience Center and we sincerely apologize for any delays in responding to your email. We are working diligently to respond over the telephone and through email to all of our customers. We are sorry to learn of the problem you are experiencing with water leaking from the bottom of the freezer. Unfortunately, we are unable to determine from this location the exact cause of the problem. We recommend that you contact a certified technician for an accurate diagnosis. Once the problem has been diagnosed, please contact us back so that we can review the concern further to determine if assistance is available. For your convenience, we have provided below service providers in your area that you may contact for service. Aries Appliance Service (925)367-7708, Vigil Appliance Service (925)371-7701. You are a valued customer and we do apologize for any inconvenience this concern has caused. We invite you to contact Maytag again either by calling (800) 344-1274 between 8:00am to 8:00pm EST weekdays or by emailing whenever the need arises. When calling please press the available option or stay on the line to reach a representative.Frustrated I went online and found this forum where hundreds of other people had the same issue and that many of them were resolved by the new P Trap. So I watched another video by the same guy on youtube that showed how to replace the P Trap. I went online and found the replacement P Trap Manufacturer model # w10619951. One of the comments there actually said to call Maytag first as they were able to get a replacement P Trap for free. I believe if it was under a year old they would also pay for the labor to have it replaced. So this morning I called Maytag, the first guy Jim said I would have to have a certified Tech come out (76 dollar service fee, plus whatever the labor would cost) and Maytag would cover the cost of the part. I asked Jim if he could just send me the part and Ill do it myself, he reassured me that he could NOT do this and that the system was very specific. I told him I did not understand that a bad design and known quality defect, why should I have to pay several hundred dollars to fix? He told me that was the way it is. I asked to speak to his supervisor and put me on hold. Not only was the hold music extremely obnoxious but there was a loud humming noise as well, I waited for 10 minutes hung up and called back. I spoke with Maggie this time. I told her I wanted the part sent to me and if she couldnt help me I wanted to speak to a manager. She said she did not have the authority to ship me the part without approval. She said she could ask for approval and after waiting for about 3 minutes she came back on the line and said she spoke with her supervisor and that they would be sending me the replacement P trap today via FedEx. Had they not sent me the part my next stop was going to be the better business bureau..

I love my gas stove. Mine is a five burner in white. Easy to clean and an accurate baking oven. Keeping the burner area clean IS a constant chore with a white surface. It would be lovely if the company made liners to catch the mess, but alas, I make my own with aluminum foil. This is an excellent stove and I’d buy it again! No buyers remorse.

We had a Fisher & Paykel Washer that lasted 14 years. This Maytag Bravos XL washer has been the worst machine I have ever owned. The clothes come out dirtier than ever. In todays world all technology is becoming disposable, Where is the Maytag repairman now? I have tried all of the settings, to have a decent wash. I am ready to throw this out. Lowes you need to do something about this. It may be made in America but now we know why Japanese and Korean electronics just work! Damaged Clothes/Clothes not being washed thoroughly enough are my biggest pet peeves with this washing machine.

I have had my Maytag set for shy of 2 full years, of actual usage time, that is. My dryer seems to be functioning normally, minus an occasional lengthy cycle time, even after the clothes are dry. The washer however, is sitting in my garage now. F51 error code, which online told me the rotary position sensor was the issue. Yes, I was told by an A&E repairman, who was at the house for an unrelated repair, that it was the bearing that was bad. When he showed me what I was looking for, there was the bearing laying in the clear plastic housing, in the underside of the washer. Its going to cost around $350.00 to get the part, if it can be found, and the service call. No, not really worth wasting more money on it. I am very unsatisfied with this unit. With 4 kids and 2 adults at home, I expected much more from the Maytag name.

In April 2010, I replaced my washing machine (still functioning after 12 yrs) to upgrade to what I believed to be the top of the line Maytag Bravo 5.2 HE washing machine. Module # MVWB850WL0 type: 580-02. This machine of 3.5 yrs leaks underneath and after having the service tech come to look he advised me it will cost over $800 to fix (I paid over $900 for this unit). He says its the bearings and went on to ask me if Id been using the HE laundry soap (as if Im an idiot) and went on to ask whether Id been washing bedding. SERIOUSLY?!? !... After much research on this issue, I discover that there are similar complaints all over North America. Very disappointed and I want this lemon replaced by Maytag.

The washer does not wash good on the initial wash. I have to wash my clothing twice. Cost and time consuming. The washer is “HE” and the water level is never enough. My clothes be saturated with dirt/lint scum and I never overload my washer. HELP!!!

I have NEVER written a review however I am compelled to write up and if I can save at least 1 family from making the mistake I did then my review will be worth it so just before Christmas last year I treated myself to a new washer. I looked at so many. Only 2 things on my wish list were 1) American Made and 2) have a large capacity for blankets and bedding. Well, I was so excited about my Maytag Bravos XL Washer but my excitement didnt last long. 4. There is a major design flaw in this machine. I have given it plenty of time and have tried to talk myself to liking it but when you have to wash the white loads at least 3 times to get them clean and still not getting the results expected then its time to admit to yourself that I made a mistake.The large capacity drum is an irrelevant because once the clothes are wet they become too heavy for the drum base to actually agitate the clothes. What ends up actually happening is your wet clothes sit in a pile. The user tends to scale the loads back to help the machine. The above problem is partly due to the fact that the machine NEVER fills up the drum with enough water to submerge the clothes where perhaps they would be able to move freely with the base agitator and the drum rotating. This model was marketed as water conserving however we find ourselves washing loads 2-4 times to achieve the desired outcome. Conserving water at this point is a joke... we end up using more water and energy to get a load of clothes clean.Bleach dispenser does not empty completely during the white cycle even when less than recommended measurements are used. If a load of whites needs to be washed we have to wash with bleach on the 1st go, and then 2 more cycles without bleach. Otherwise anything washed after the whites gets spots of bleach on them. For these and many more reasons this machine should NOT be on the market and especially not for over $800 USD! And I would not want this product to represent US production. It does not deliver on any of its selling points and is overpriced.