I moved into this house and the dishwasher came with it. For an appliance that is over 8 years old it works beautifully. It cleans my dishes well and doesnt leave residue on them. I ran it through a cleaning cycle recently and that has only improved its performance. I recommend dishwashers by Maytag because they last and perform well.

The dishwasher turns on of its own accord. Sometimes when you get too close to it, once in a while in the middle of the night, and most of the time when you latch the door. It does a great job cleaning the dishes, but to no avail because its always in the middle of a cycle when you need them.

Failed control panel Quiet Series 300 - After seeing countless notations on the net concerning failing touch panel and control boards, now my relatively new dishwasher has started its demise. It is terrible that so many people have the same problem. I sent an email to Maytag and have promptly been ignored. Unless it sets your house on fire, I guess they are not interested as I am no longer interested in supporting this product. It is nice that you can post such similar design failures for the world to see. Thanks Maytag!

I purchased a Maytag dishwasher May 2019 Model# MDB4949SDE3 Serial# F80446835. It has to be one of the worst purchases I have made in a long time. In fact, I wish I could return it and start over with another brand. My glasses come out of the cycle with film and silverware is spotted. I have tried everything from scrubbing and rinsing before I put into the dishwasher, every product on the market, making sure my hot water heater is on high to settings for the longest most powerful cycle and it still continues to disappoint. My warning is DO NOT buy this dishwasher.

We have had this dishwasher [Model MDB7749SBW2] for about 1 1/2 years now, and gave had a lot of trouble with it. It will run a cycle on its own without anyone even touching a button. My current problem is the start button wont work. I reset the dishwasher by pushing the series of buttons I found online to do a reset, and the start light lit up, but after the reset cycle was finished I tried to run a wash cycle and couldnt get the start button to do anything. Ive seen a lot of reviews online on this being common with Maytag brand dishwashers this old. I will NEVER buy a Maytag product again nor would I recommend it to anyone as a good product. I am very frustrated and disappointed in Maytag!!!

My dishwasher is 9.5 months old. The computer board needs to be replaced and they cannot find the part. It’s been 2 1/2 weeks since I called in the repair which is under warranty. I was told they have 10 business days to search the country. Really search the country. Does anyone know what will happen if they cannot find the parts I need?

We love our Maytag Dishwasher! It's very durable, doesn't use a lot of water and really gets our dishes exceptionally clean. The best part is that it sterilizes on the final cycle! We've long trusted any Maytag appliance in our families for generations.

My dishes come out super clean and I love it, even when there is calcium build-up around the filter. Thanks to Maytag and their great technology. You cant beat Maytag.

After 1 year and a month, the dishwasher would not work. When the Maytag repairman came, he told me that this was the 3rd one this month that had the same problem (the control panel). The cost to replace, it would be about $275. However, since I know of 3 that have broken, why would I replace it? I live alone and maybe have used the dishwasher once a week. There should be a recall on this machine. I called to see if there was a recall and was told Im sorry. I would advise anyone purchasing a dishwasher to avoid Maytag or any dishwasher made by them.

I bought a new Maytag Quiet Series 300 in 2005 and have had nothing but problems with it. The internal plastic pieces that hold dishes in place have broken off regularly. The door handle also broke. The dishwasher does not drain all the way every time. Now, the dishwasher will quit randomly before finishing its cycle. Our model (MDB7600 AWB) was not part of the recall, but is a lemon nonetheless. Of course, all of this occurred after our one year warranty had expired. This dishwasher is a lemon and a waste of $400. Well never buy another Maytag product.

Dishwasher (MDB7709AWB2) stopped running mid-cycle, internet search revealed that control panel needs replacement at a cost of $135. excluding labor, for a dishwasher that originally cost $348. Notified Maytag and am awaiting a response.

I purchased the Maytag dishwasher a little over two years ago (MDB6759AWQ0). This was the first Maytag product I bought and it is definitely the last one! It was more expensive, but because of Maytags commercials on what good products they had, I thought it would last longer and work better. Boy, was I wrong. When it was installed, it was loud. I brought this to the attention of Maytag. I was told there was nothing that they could do. Repair people were sent to my home several times to see if the noise could be fixed and unfortunately, it could not. This is the loudest dishwasher that I have ever had. I should have stayed with the same brand that was over 10 years old that died! Now the control panel blew out and will cost over $300 to have it fixed. After reviewing the numerous complaints that you have on your dishwasher with the control panels not working, I would think Maytag would be more financially responsible in helping the people that have your products that no longer work after being less than three years old. Just a heads up, Maytag, I will be replacing instead of fixing and not with another Maytag product!

We purchased our Maytag dishwasher less than a year ago and are very disappointed with the poorly designed quality of this product. We had a Maytag repairman look at our dishwasher and he told us that; the dishwasher cleans with enzymes in the dishwasher not water pressure, and we need to make sure the water in the kitchen faucet need to be hot before starting the dishwasher, we also need detergent, rinse aid, and citric acid added to each load. Adding all these products to the dishwasher does not fix a poorly designed product. This product does not clean the dishes, even with rinse aid the glasses come out cloudy. The dishwasher has a power blast button, it does not clean the dishes any better than the regular setting and it runs for four hours. We will never buy another Maytag product.

I have a Maytag dishwasher model mdb6759aws3. The control touch pad broke after 1.5 years of light use. It costs $475 to fix (includes labor). Completely unacceptable service provided by Maytag over the phone. The only concession offered was a 25% discount if I bought the replacement part (control touch pad) from them. After some internet research, I learned Maytag marks up their parts prices over 25% so they are really not giving you a discount at all.I filed a complaint with Maytag but they were unable to provide me with any evidence of doing such except for an 11-digit code. Due to a major defect, Maytag should have sent me the replacement part for free. I told Maytag I thought this was fair and that I would pay for the labor. I will never buy another Maytag appliance again! They are junk and the company does not practice common sense customer service.

MDBH979SAM0 - Bought this dishwasher from Home Depot 2 years ago and have taken care of it, never abused it or anything. All of a sudden it just starts freaking out, once you start a cycle it will wash and then rewash and then keep going costing us money on electricity, water and wear and tear on the machine. Ive tried everything but it seems like its just stuck in start mode. The indicator lights on the panel flip out too, they will all blink randomly. So when I close the dishwasher and dont intend to start any cycles and it is off it will start up all on its own so Ive had to unplug it. Funny how I called to order a control panel part and its on back order... Very interesting how they are out of this part probably because everyones ordering it.

I purchased my dishwasher exactly two years ago. We are empty nesters so it has had light use. Today, when I tried to start it, the control panel would not work. Thanks to what I found in your site. I will not take a day off of work to wait for a repairman only to have it fail a second time. It is hard for me to believe a company that builds its reputation on a bored repairman would produce a product with a faulty control panel and not do something about it. Like your other folks, I will never buy another Maytag product and will not the waste the money to repair it. I am going out tomorrow to buy another dishwasher and throw this one away.

Control panel on front of dishwasher quit. Unit is 15 months old. Bought extended warranty through Home Depot. Took two hours on the phone to finally get to the correct department, they set an appt. for the following Wednesday between 10-2. Had to take a vacation day. Get a call from the appliance repair co. the night before stating they cant live by Depots schedule, they wont be out til the following Monday between 9-1. Schedule a vacation day. They come out then have to order parts, they wont be in for 7-10 business days. After 12 business days, I call back and they set appt. between 10-2. Schedule vacation day. They come out and the control panel the warranty company sent is the wrong one. Now I have to start the whole process over again. DONT BUY MAYTAG AND DONT BUY WARRANTY OR APPLIANCE THROUGH HOME DEPOT.

This dishwasher is extremely quiet and very attractive in the kitchen. Easy to use and does a great cleaning job. The price was also right. Would definitely buy again.

I bought a Maytag dishwasher, model MDB8551AWB, in 2007 and have kept purchasing maintenance agreements. From January 2011 to March 2012, I have had to have Maytag send out a repairman to replace the control panel five times. This is absolutely ridiculous, and the inconvenience. Plus the repairmen are surprised Maytag keeps on repairing this dishwasher and not replacing it. More the $2000 has been put into this dishwasher since January 2011. When calling Maytag, I was informed that the problem would have to be the same which it has been but on the same contract for it to be classified as a lemon. Well, it has now been four times. I will never purchase another Maytag.

Maytag dishwasher MDB7749SBM2 - I purchased this unit from Home Depot. It worked fine when working. In less than two years the control panel had issues. Would not let you start cycle, would randomly start on its own, would light up randomly, would only let one cycle work, would not work at all, etc. I received no help from Maytag. After open up the door panel the problem is obvious. The ribbon cable from touch (control) panel to control board had black spots from corrosion. Poorly insulated or poor design. $150 for part and another $100+ for repairman. As Ive seen from several of these posts it appears to be a common problem now to Maytag, which they choose to ignore in spite of class action lawsuits. Obviously last Maytag product Ill ever buy.

We bought our Maytag dishwasher less than 2 years ago (model MDB8969SDM0) and we are remodeling our kitchen now January 2018, and when we pulled the dishwasher out we found that the wire (12/2) had melted into the back panel. We won’t be putting this Maytag back in.

I purchased a Maytag MDBH979SAB0 dishwasher from Home Depot two weeks ago for around $600. I got it installed and it would not turn on. I contacted Maytag and after a few questions, she stated that they would have to send a repairman. After a few days, the repairman arrived and said hed never seen this model before but that we needed a new control panel. After waiting a week with no work, I called Maytag to get an update. The control panel is out of stock and could be a while - they are trying to find one somewhere around the country. They refused to send a replacement dishwasher, even though this was brand new. Their policy says repair, not replace. Dont take the chance purchasing a Maytag dishwasher.

I bought your Maytag model MDB7749SBW1 dishwasher on May 22, 2013. We bought Maytag because of your reputation...not because of price. However, in September, 2014 (2 months out of warranty!!), the control panel stopped working. I called the 800 number and the best they could do is to extend the warranty for 6 months BUT only after we paid for repair and control board replacement. This is not cheap!!! We were furious. I looked if there were recalls on this model but there is not (should be). Anyway, after we paid for repairs and a new control panel put in ($160.00 +- for part itself), we were very cautious about touching anything on that dishwasher. YOU HAVE an issue with design and I can give you link after link of other customers who have expressed the same thing. So, here we are in 2017... About 2 months ago, we noticed the exact same symptoms with the control board.In fact the ONLY way we could start the dishwasher was to turn off the breaker, let it sit for 20 minutes - overnight and then turn back on and hit the start button. We lost all control over the settings. Only auto clean and delay 2 hours were working. Yesterday, I purchased yet another control board ($179 incl tax and shipping). I plan to install myself. If I could afford another dishwasher, I would do it and never buy Maytag again. Maytag really ought to be ashamed and if they were truly concerned they would offer these defective parts at a steep discount or better yet, recall. I plan on submitting something about this issue with any consumer group I can find. I guess the only way to spread the word and perhaps force a company to respond is to post on social media anymore. This is NOT a like.

Within 2 months of 1 year warranty running out, the control panel went wacky - does all kinds of weird things except work right. Called to see if there is any suggestions or work arounds and was told they would be glad to set up a service call for between $70 and $100, where they could tell me how much it would cost to fix. As with the other 100s of folks with the same problem, they basically said gee, you should have bought an extended warranty. If you have this many people with the same problem then it is Maytags problem, not the poor sucker consumer who got stuck with it. If you are considering this dishwasher, run, dont walk, as far from a Maytag or Westinghouse product as you can get. If anyone starts a class action suit against this product, please count us in!

We bought MDB7759AWB Maytag dishwasher in 2011. It worked decently until now when it stopped delivering water to the upper rack. The cleaning quality on the lower rack also dropped significantly although it might be due to the lack of water delivery to the upper rack. Apparently there is something wrong with the internal pump. The Maytag service offered a repair for $300+ which I rejected because this is a ridiculous cost and I would rather buy a different dishwasher. My conclusion is that if you buy Maytag dishwasher you need to factor about $300+ for the repair(s) in 5 years as apparently they do when they sell you this product. Anyway, even though Maytag was a decent brand a long time ago (probably in the past century), it is not reliable anymore. It does not mean it has to be much worse than many others but if you are looking for something better than those others I would not recommend Maytag.

We just had the same problem as most of you have posted. The control panel malfunction. Model MDB7749SBM. Our issue started after only 18 months when the dishwasher would start on its own and/or cancel a wash on its own. I think this is a major issue if a home appliance can start on its own from the off position and run through multiple cycles. I think this could be dangerous if you are out of town. Our cost to replace the panel was more than 1/2 of the original purchase price. This is a major defect and should be handled by Maytag if they are a company with any integrity.

I bought this Maytag dishwasher model # MDB7749SBM2 and of course it ran great until the warranty was up and then the touch pad started acting up where if you would press normal every other thing would light up. I replaced the keypad and then the controller and its working at this point again. The keypad ribbon cable had a big burn mark in it and by all these complaints it seems like an issue Maytag has and does not want to address. Luckily I work on electrical and was able to do this myself and I had no labor but over $300.00 in parts. What upsets me is I bought because of the reputation and the Made in America on it and it was replacing a 20 yr old Kenmore that was still working great when I took it out. With all the complaints about the same issue Maytag which is Whirlpool would step up to the plate and fix this. No more Maytags/Whirlpool for me again.

We purchased a MDB8949SAW dishwasher in 2013. 1 month after the warranty expired the touch buttons went on it. If you selected normal it would opt for something else like rinse only. We researched online and my husband followed instruction online to take the door off and seal the moisture to prevent this from happening. This worked for about 2 months and now back to the same thing. We paid $500 for this and just living with the problem for now. All we can do is warn others.

I bought a Maytag Dishwasher Model #MDB7749SBW2 in 2013. It worked great for 2 years. In 2015, the control panel malfunctioned. All the lights on the control panel would light up and the dishwasher wouldnt start. I called Maytag. They sent out a service tech. He replaced the control panel. I started having the same problems two years later, 2017. I called Maytag today, 9/11/17, to see if they had recalled this dishwasher. No, it hasnt been recalled. They offered to sell me a extended warranty for $400+, that would pay for the service call and parts or, I could find another Maytag, Whirlpool or KitchenAid dishwasher and depending on the model, I could get a 25-45% discount on a new one. I asked why they havent recalled this model, due to the problems that so many people are having. They dont know. Im writing this review to let those of you who have bought this dishwasher know, that the product is faulty.

Just like all the other reviews, the control panel on our 3-year-old dishwasher stopped working. The obvious defect of the product and lack of customer support is unreal. We ended up replacing the Maytag with a Frigidaire. Hopefully it lasts more than three years.

Maytag dishwasher mdb7749sbm2. Purchased the above Maytag dishwasher model in July 2013. Eight months later the control panel ribbon strip burnt out. The first of many times to come. I had the panel replaced three times during the first year (warrantied by Maytag, now Whirlpool). All I can say is thank goodness, I paid $30.00 for the extended 3-year warranty. It has been the best $30.00 I have ever spent. Unfortunately it doesnt count for all the frustration this appliance has caused me. Ever since the first repairman walked through the door, all he could say is that the control panel was poorly made, electricity and water does not mix and never will. When you use the steam option all you are doing is adding to the problem. (The steam option is the sole reason why I bought the model in the first place!)Anyhow, this model has broken down three more times and it is currently down again as I am writing this, awaiting for a service person to hopefully come out as promised next week. I purchased this appliance two years ago and still have one more year of warranty left. Once it is done, I will be shopping for another dishwasher. If I didnt have it covered with a warranty, I would be paying the service fees of about $251.00 each time they came to change the panel. Shame on Maytag/Whirlpool for not recalling this model.

Maytag french door fridge model MFF2558VEW7. I bought this fridge about 3 years ago. Have had nothing but problems. First I had problems with the freezer frosting up, then I had the same problem of ice buildup in bottom of freezer. Now the freezer only gets cold enough to cool drinks and the fridge only gets to about 60 degrees. This is not the only Maytag appliance I have had problems with. I bought a dishwasher a few years ago that quit working just after the warranty ran out. Both bought from Home Depot. After reading other reviews, it seems that appliances bought from Home Depot have had problems too.

Dishes did not get clean. Bowls would stand up when you placed them in the dishwasher, then fall over when the door closed and came out dirty. The rims of glasses were not clean. I had several 3 service calls and changed dishwasher soap several times per their suggestions. I contacted Maytag and was told that the only warranty was for mechanical problems and since the problem was not mechanical there was no warranty. I then went through the Better Business Bureau. The ultimate decision from Whirlpool was It has been determined there are no defects with the dishwasher and the issue is use and care. Mrs. **s request for a refund is respectfully denied. I have purchased a new dishwasher which does clean the dishes and the Maytag is sitting in my garage gathering dust.

Nothing wrong with this dishwasher, a bit noisy, but it gets the dishes clean and thats whats important. This was a builder grade installation and it came with the house so I cant really say its the exact model I would have selected had I been given the opportunity to pick my own.

I purchased the Maytag metal interior two years ago, the very first year I had to replace the control panel board... Now, the panel went out again, after calling the Maytag executive office, they finally sent me the part, telling me I had to pay to get it fixed. That was just three months ago... Presently, the dishwasher has quit running water in the cycle... I will NEVER purchase another Maytag dishwasher... thinking you get The Best doesnt mean what you think... BEWARE...

We purchased a Maytag Jetclean Plus Dishwasher in June 2013. It worked well enough initially. We bought it because it had a large capacity and built in disposal. By August 2014, just after the warranty expired, the front panel gave out. To have someone even look at it cost $150. By following instructions from internet discussion groups by other people facing similar issues, we were able to get it to run in random mode. Programs were no longer indicated or selectable but dishes generally still got cleaned. Two months later a wheel fell off the premium rack glides. Finally after about 2 years of use, the dishwasher finally gave up altogether. At this point the stainless steel tub is no longer stainless. The entire device has worn poorly and looks shoddily made. This is the worst use of $900 I have ever made, and what tweaks me the most is Maytags attitude and their ludicrous warranty that barely lasts out the weakest link in the device.

I too had to replace the control panel on my Maytag dishwasher which I purchased in 2007. I was told by my repairman to contact Maytag to see if they would do anything for me. When I called Maytag, I asked them if there were any issues with the control panels as I had heard there have been multiple issues with them needing to be replaced. I was told they had no record of any complaints and offered to sell me an extended warranty for $269, but there was nothing else they could do for me. I ultimately had my repairman order the part and it was replaced. My repairman did say Maytag did upgrade the panel because of all the issues they were having with the panel. Hopefully, they have fixed the problem and it will not have to be replaced again. But if it does, I will not replace it again. I will look into a new dishwasher and definitely not a Maytag. Yes, I would be interested in joining a class action suit.

We purchased our Maytag dishwasher on 12-26-2013. It was installed in early Jan. We did not buy an additional warranty. We put our faith in the Maytag name. We had no problems with our dishwasher. It was smooth and quiet. The one year warranty ended in Jan. 2015. In March of 2015, our dishwasher control panel began to go crazy. A short while later our Maytag shut down completely. Every now and then the washer will come on by itself. We will try and cut it off. It cuts off when it is ready. We have got quotes on getting it fixed by Maytag. With installation and tax, our Maytag Dishwasher cost us $649.22. Our complaint is the same complaint of thousands of other customers - the control panel. Maytag should have a recall and fix this problem. Maytags remedy for this problem is to sell a warranty for each year that a family owns the dishwasher. That is not acceptable. Please consider a recall on this item. Our model is MDB7749SBW2. Our serial #F33406909. Thanks for your help.

Purchased this Maytag dishwasher (Model DB7749SBM2) from a Sears 2014, no problems until now in late June 2014. The control panel is not responding. Start/Resume light is off, pressing it doesnt seem to do anything. Cancel light is off, pressing it does trigger the cancel drain process. Wash Cycle choices either dont respond, or for 2 of the choices engage an incorrect cycle. Option choices dont respond. Delay light comes on when an incorrect cycle choice displays but stays at 2 hours, cannot be toggled off or to a different delay length. Holding Control Lock or Delay for 3 seconds doesnt seem to clear the circuit board logic. Problem began with the Cycle choice buttons defaulting to Rinse Only. Control panel behaves not at all or incorrectly as described above. Seems to be a common Maytag control board/panel problem. We need help as we are unable to afford repair or another dishwasher. This time, it will not run at all. I called customer service today (August 11, 2015) and they expect me to pay for the repair. Repairman already said electronic board bad at a cost of around $300 just for the parts. It is easy to Google and find multiple review sites that indicate hundreds of consumers have similar problems, but Maytag will not acknowledge any issue. Based on the pattern the warranty is not going to help as it goes out just after a year. For only having it 1 1/2 years it is becoming very expensive. There should be a recall on this control panel.

I purchased this dishwasher at least 12 years ago and it still works. However, after that much use some of the buttons no longer work. It has china, economy, regular, rinse only and extreme wash features.

I wrote earlier about my dishwasher needing to have an electronic board replaced again. So I called the helpful (I say that with sarcasm in my voice) 800 number. My dealer asked me to call for help with paying for the new part. After an hour and a half of being cut off and put on hold, I finally got through to a person that could take my request. The gentleman explained to me about why they would not stand behind their product which was only 3 1/2 years old, and a replacement part that lasted only 11 months. He expanded on his thought about how it was too old to fix and the part was more than 90 days old. I am out of my $1,100.00 with no help in sight. Totally upset with this company and how they will not stand behind a poorly made product!!!!

I bought a Maytag dishwasher, model # MDB7749AWW1, in April 2011 and the control panel just stopped working. Of course, Im outside the one-year warranty, but judging from the other reviews on this site, that doesnt really matter. A $500 dishwasher should last more than 17 months! I agree with the other consumers. The control panel on these dishwashers should be recalled. Obviously, its defective. Instead, Im being told I can either pay $250 for the repair plus a one-year warranty or $130 plus parts to cover a onetime fix. Ridiculous.

I bought a Maytag dishwasher in January 2013. Three months later, the cheap plastic latch on the door malfunctioned. I waited 3 weeks for the repairmen to get the part in. Is there a sense of urgency anymore? If I owed Maytag money, I bet there would be a real sense of urgency on their part. Next time it will be an LG dishwasher.

Its frustrating the way the bottom of the dishwasher has curves making wasted space. Second, the tracks for the trays are such that often the tray comes off the track and makes it difficult to get back on without unloading dirty dishes to do so. Finally, I really dont get the lighting system for dishwashing on the outside of the machine.

I have a 2 year old Maytag Dishwasher (barely used - it is a weekend house) MDB7749sbm1 and the control panel went out about 2 months ago – I followed another person’s advise of hitting normal and heated dry buttons 3x quickly and that seems to wash the dishes – not sure what cycle it is on because all the lights go on including 2 hr delay. I called Maytag and they kept me on the phone and hold with multiple agents for 34 mins and finally agreed to send someone at no cost to see if the problem can be fixed with no cost to me. I will keep you updated.

I purchased this dishwasher about eight years ago, and I love the performance and the stainless steel interior. I never have a problem getting my dishes clean. This product definitely lives up to its reputation. Going forward, I would definitely buy the same brand if it became necessary.

We updated our 25 years old dishwasher, which ironically still worked, to a Maytag we bought at a BrandsMart in GA in November 2010. Sixteen months later, the unit just died. The panel would light up, but would not run. We contacted Maytag and were assigned a repairman (The Appliance Guy) who could not come to fix the dishwasher until 5 days later. Once he finally showed up, I was informed by him that the control panel for the dishwasher had two shorts in it and it would be cheaper for me to just buy a new dishwasher because the repair to this one would be $344.44. When I contacted the customer service for Maytag, they offered to let me pay for the repairs and then they would give me a six month service warranty for free. Does that make sense to anyone? I could buy a totally different brand, brand-spanking-new and have a twelve month warranty with a better product. I asked to speak with Cheris boss and got to speak with Aaron, who offered me the same spiel. Heavily scripted, I apologize that you are dissatisfied, but all we can do is give you the service warranty for six months after you pay for the repair. I asked him if he was reading a script and he replied no. Now I know that he had probably repeated these same words twenty times a day. Heres a thought, Maytag claims to be a green company, using less electricity and water, and saving the customers money and yet they are filling up all the landfills with these appliances that are not even five years old. How is that being a green company?You know how when you buy a nice new button-up shirt? The makers of that good quality shirt go ahead and sew an extra button on the inside bottom part of the shirt because they know that theres a chance youll lose a button. Well, Im thinking that Maytag should just start shipping a couple extra control panels in every box of Maytag dishwashers. Crazy idea, right? Okay, so an easier and cheaper way for Maytag to correct the problem is to stop making dishwashers. Go back to the drawing board, make the engineer who designed the control panel wash everyones dishes (as punishment and he can get help from the customer service people because theyre really doing nothing), start building the old design dishwasher that has the old switch and dial, and start respecting their customers. There, problems solved!

Purchased MAYTAG DISHWASHER MDB7809awm in 2011 for $719. In 06/2013 the far right 3 buttons stopped working. I contacted Maytag to see if there was an issue with this and they reported that there was not. I had the part replaced in 06/2013 at $280. It cost me 1/3 of the purchase price of the dishwasher. The repairman said that he sees this a lot with Maytag control panel issues.On 08/02/14 the same exact issue occurred. I contacted Maytag online on 08/02/14 and didnt hear back until 8/13/14 to say that there was no known issue and all they could do was recommend a repairman. I also called before I heard back via email and they said the same exact thing, there is no known issue and we can do is recommend a repairman. I am not interested in repairing. Been there, done that. Not doing it again. I researched the issue of the 3 far right buttons not working and there are several forums and discussion topics out there. I find it hard to believe that MAYTAG is not aware of this issue. If you GOOGLE the model you will see the same issue. Not only is the MAYTAG product poor, but they have the worst customer service I have ever seen.

We bought our $600 Maytag dishwasher less than two years ago and have had three separate problems with it, from faulty instillation, to a faulty seal to faulty control panel. The first problem was covered under warranty, the second problem we fixed ourselves and the third problem, nothing can be done except pay an additional fee of $250+ for a new part. Maytag used to be a good name but with three problems in under two years, the only guarantee given is that if you buy one, be prepared for problems. This company does not stand by their products and will only ask for more money to fix their faulty items.

Faulty control board. Have owned a Maytag dishwasher model MDB6769PASI for 2.5 years. The unit started beeping at random times for about a week - then went dead! Sounds like other reported failures and it is unlikely repairs will be permanent! Never again Maytag.

Very disappointed with my 2014 purchase of model MDB8959SBS3 dishwasher. In fact it is no longer in service. We used the dishwasher approximately twice a day. The wheels on the pull out racks starting falling apart in the first 6 months. Then the soap dispenser failed. It would not shut. We replaced both the wheels and the dispenser only to find ourselves with the exact same problems in a matter of months. My hubby got really good at fixing both of these items. The final straw was earlier this year as when we turned it on the motor/water pump started making a screeching sound. Never had to replace an appliance that was only four years old in my lifetime. Just very disappointed with the quality of Maytags dishwasher.

We bought a Maytag Dishwasher on March 16, 2013. Less than 10 months, we had repairman come in 5 times. First was soap scums left on the glasses after a wash. Then, the soap dispenser was leaking. Now the control panel is not working. We have to wait for a week for the parts to come in. Total length of time for hand washing dishes since we bought this dish washer is three weeks. They said they are not going to replace it until it cant not be repaired. What does that mean?? Please never ever buy Maytag dishwashers!!!!!

This is beyond one of the most disappointing purchases I have ever made! It has been about 15 months since purchasing this dishwasher, and as of today it is not working! Blinking start button. I see from the hundreds of disappointed customer comments that I am not alone. With this many people complaining of the same issue, that Maytag should have a recall... I paid about $550. I get that quality does not supersede the almighty dollar, but come on!

I purchased a dishwasher model #MDB4709PAM from home Depot in March 2014. There is something wrong with the electrical and it is shocking people if you touch it. Just so were clear.. MY DISHWASHER IS ELECTROCUTING PEOPLE... Called Maytag repair because hey its only five months old. Cant send anyone out for three weeks.... three. Took an hour on the phone because I had to talk to four departments. Kept asking if anyone had been hurt seriously or property damage, so they made sure their butts were covered, sigh..... Should have bought the LG.

I bought my Maytag stand alone dishwasher model # MDC4650AWB in August of 2009. I have used it once or twice a week since then. About 2.5 years ago the control panel crapped out. I forked over the $$$ to have the part replaced and installed. Now, 2 years later the panel is once again slowly dying. I just got off the phone with the Maytag people and they refuse fix it and take responsibility for the product failure. The machine has worked adequately for me aside from the control panel issues. The control panel was built to break. Shame on Maytag! Lets go forward with the class action lawsuit!!!

Model MDB7749AWM2. Paid over $700.00. Figure I would get a good dishwasher so it would last and clean dishes. I was wrong. I replaced all new appliances for kitchen in house we had purchase 3 years ago. I replaced door switch 4 times, front door panel where screws go in broke off. Salesman at Lowe’s said Maytag was a good dishwasher. It is a stainless front and stainless inside. I have had cheaper models and never had problems with.

Purchased Maytag Dishwasher MDB8959SFH4 as part of a kitchen renovation with hardwood floors. Realized that the dishwasher was leaking intermittently. Appeared that the door wouldnt latch properly. Called Whirlpool (parent company). Technician came out to assess the situation - couldnt recreate the problem so suggested replacing door seal. I try to explain to him that in my opinion it wasnt the door seal but a failure to latch because the top rack was not retracting completely on an intermittent basis. He also suggesting replacing the latch. Repair was carried out and same issue arose three days later. I systematically removed one dish at a time and then tried closing the door - after removing about the 6th item the door closed. Called the repair company today and they told me he had just received a recall from Whirlpool - apparently an issue with the tracks not allowing the rack to retract properly - what I have been saying all along. I called Whirlpool but they insisted the notice was sent out some time ago. I called Home Depot where I bought the appliance and they confirmed that they were not aware of this issue. I suggested they should not be selling this dishwasher until Whirlpool remedy the manufacturing defect. I will follow up with Whirlpool to let him know I have spoken with Home Depot and they were not aware of the issue.

Purchase in April 2010 on 12/31, motor and computer panel went out, not washing. I do not recommend this dishwasher cost to repair. Too expensive.

Maytag Dishwasher MDB77495 - We bought this dishwasher September of 2013. April 2013 when you pressed the option I wanted the options auto clean, rinse only, steam sanitize and delay hours. The thing would work when pressing start but I have no idea what it is doing. The repair man replaced the board and all was good for a couple of months then it happened again. The board was replaced again and in two more months it failed again. The repair man told me that moisture was getting to the board and there was corrosion on the ribbon mentioned in another review here. He contacted Maytag both times and gave them my contact information but they never called me + they told him that they have never heard of this happening with this machine. We had a Maytag machine 8 years ago where the board actually melted but like an idiot decided to try them again. I will never buy a Maytag again.

We purchased a Maytag dishwasher in July 2013. In October 2014 it stopped working. None of the buttons on the control panel would light up. The service technician diagnosis was that it needs a new control panel at a cost of about $200.00. We chose not to do the repair since the technician recommended against it.

Our brand new Maytag dishwasher model number MDB87749SBM2 was professionally installed on 7/31/2013. In fall of 2015 my control panel started acting up. I was unable to select certain wash cycles. The problem would come and go. By January 2016 my lock button would freeze and I was unable to unlock or select any wash cycles. By February 2016 my control panel went out completely. It wont turn on, not a single light. It is fried.When Googling the issue I found that we are 1 of MANY with faulty control panels not only on our particular model but on many Maytag dishwashers. They all seem to have the same problem, right around to 2-3 year old mark. One would think dishwashers would last, like before. A dishwasher shouldnt need to be replaced or need a major repair so soon. The one our new dishwasher replaced was 12 years old and was working just fine. We just wanted to upgrade to stainless steel. Wow what an upgrade haha! Maytag should be recalling these control panels. Their name is no longer a trusted name in our home.

I purchased a Maytag energy efficient dishwasher in June of 2010 along with an extended warranty that I keep extending. Cost $ but needed. Issue: Sensor in Panel fails so far every year and needs to be replaced. The repair technician showed me the sensor strip and indicated that this has been a big problem. (At least I have a warranty; however, it is a big pain to have to schedule a service repair person to fix the problem.) Repair (Sears) is EXCELLENT with great customer service. I did contact Maytag and there has been no recall.I own other Maytag appliances such as a washing machine and refrigerator with no issues there. In any case, I needed to replace my clothes dryer and did not select a Maytag. I purchased a GE very simple product with no sensor/bells and whistles. Not sure if I will go back to Maytag in the future - depends upon how they handle problems with their appliances. I would rather pay extra money for quality, durability, and reliability than go through the inconvenience from parts that are not made well enough to hold up.

I had the exact same experience as the Tampa person with my Maytag dishwasher (Model: MDBTT60AWW). It was not cleaning the dishes, even when I thoroughly rinsed them. Plus, it started leaking midway through the cycle. Since the warranty was expired, I purchased an extended warranty in July 2012 for $296 (yes, in hindsight, I should have just bought a new appliance, not Maytag). I had 3 visits from 2 different technicians, both telling me the dishwasher did not leak. One telling me I was using the wrong kind of detergent and thats why dishes werent getting cleaned. The other telling me that there were too much suds and that could cause it to leak. So, I should pour a tablespoon of cooking oil (yes, cooking oil) in the dishwasher when it starts leaking and that will cut down the suds. I dont think so!Then, I found out a couple of weeks ago that this model was under a recall since 2010, not related to the leak at all. Yet, Maytag still sold me the extended warranty (wheres the ethics of that?). I requested a pro-rated refund of the balance on the warranty - and wouldnt you know that with the technicians service calls, the amount of time used on the warranty (6 months) plus an admin fee - I have used $296.48 of the warranty amount. It is almost to the exact penny of what I originally paid, so I will not be receiving any refund. They are only giving me a debit card of $150 or $250 once I buy a new Maytag to replace the recalled model. I do not want to continue down this frustrating path known as Maytag appliances.

We purchased a high end Maytag Dishwasher from Lowes just 2 years ago. Within a year the machine was turning itself on, beeping for no reason, and eventually the functions on the control panel stopped working. When I called Lowes they gave me a number for a repairman who informed me that the cost of a new control panel would be $514 and its a known issue with moisture getting into the control panel. This is unacceptable. There are hundreds of complaints and a class action lawsuit regarding this issue and yet Maytag has done nothing to remedy this situation. I am forced to purchase a new dishwasher and I will never purchase another Maytag product.

Do not buy this dishwasher unless you get the extended warranty. We purchased this dishwasher in Jan 2014. The first one delivered was completely busted up (which was probably the delivery companys fault for not handling it correctly). Then we had to wait for the replacement one to come in to get installed. In Sept 2014 the control panel stopped working. It was repaired under the warranty but it took several weeks for the authorized repair shop to be able to come out, diagnose, order part, and then come back to fix it. Now March 2015 (5 months later) we had the same exact problem with the control panel. The repair company was unwilling to order the part to bring with them even though they already had it in their records what we needed due to the previous repair. It was going to $300 to repair it since they only warranty the repair for 90 days. We decided to replace our 14-month old dishwasher rather than put any more money into it. Shame on you Maytag for putting out such a bad product - obviously this is a common problem. It is quiet and does a good job of washing but to have it take several weeks to get a repair done combined with having a problem that cost 50% of the purchase price to replace twice within a year of each other, absolutely not worth the money. Should have just spent the extra on a higher quality product. Will definitely get the extended warranty on whatever we replace it with.

I have always hated soft touch control panels so I purchased a Maytag Dishwasher with old style push buttons. IT DID NOT CLEAN THE DISHES, so Lowes took it back and I was convinced to UPGRADE to an MDB7749SBB0 and was told this machine was top of the line, although it was VERY temperamental from the start. I guess I should have done my homework. I see now several complaints about the control panels not working. I was told that MAYTAG was a very reputable company and that they stand behind their product. WRONG!. The company KNOWS these panels have problems and should replace them free of charge as it is obviously a defect. Nope, first they offer to send someone out (In a week) to repair it at $80 just to look at it and the panel is over $100 to replace, and when I complained they tried to sell me extra coverage for $250. REALLY? What is the purpose of purchasing a QUALITY dishwasher? I might as well purchase a cheap dishwasher and replace it when it breaks. I think you should be responsible for your product when you have several complaints on a specific part.

The control panel died on this dishwasher (MDB7749) after only 2.5 years of light use. I was quoted about $250.00 plus labor to have the panel replaced. I will not fork over several hundred dollars for a defective panel, especially since many others have complained about repeated failures and known issues with the control panel. No more Maytag products for me. I plan to purchase a Bosch to replace it.

This dishwasher constantly has an odor. I run the dishwasher every third day (there are only two of us), and no matter how well the dishes are rinsed off, there is an unpleasant smell whenever the door is opened. Even after running the washer, upon opening the door an unpleasant scent still lingers. I compare this washer to the Kenmore I left in my previous home and this brand new one falls short. I would not purchase this dishwasher again. But because this is only a year old, I guess I am stuck with it for a while.

I am sorry I purchased this machine. It was meant to replace a 17-year-old Maytag dishwasher that was not repairable. I figured they were good machines. Wrong. Perhaps I have a lemon, I do not know. I bought the machine on the 23rd of November and it was installed on the 29th of November. Here it is December 12th and I am sick to my stomach. I have already had to contact Maytag customer support and have a repairman coming. This machine does not clean worth a damn! My glasses look worse coming out of the machine than when they went in. I have run two loads with the machine so far. The auto-sense cycle is a joke. It took over four hours to complete and things did not come out clean. Last night I tried the normal cycle. It came up with a run time of 2:36. The first rinse was cold water. The detergent cup was open and empty at 20 minutes in. So what does the machine do for the next two hours??? When the cycle was finished I looked at the glasses and they were spotted and streaked with remnants of fingerprints and lips. So I ran it again trying the quick cycle. Not one bit of difference, still nasty looking glasses. If this machine cannot get the upper rack clean, how can I be sure the lower rack is getting sufficient cleaning? One would think that for $600 it could at least do the job it was meant to do.

I wrecked on a bike, had surgery and in a wheelchair. I bought and had a Maytag dishwasher delivered from Beaumont Home Depot and this mdb7749sbw2 model never never worked. Home Depot told me I had to bring it back myself (Im in a wheelchair at the months that was impossible) and I called Maytag warranty. They sent a tech. He replaced a front power panel that didnt work. They sent out two more techs and they said use other soap Lemi Shine and the other guy said use Finish and turn your hot water heater all the way up. That never worked either. I have had this a yr and it just sit there and money in the trash. It makes me sick.

I was having similar issues with my Maytag model MD dishwasher. The unit was operating, and then the start/resume light began flashing. Didnt think much about it since the machine continued to run. But the machine wouldnt cycle off, or rinse or dry. It continued to run, with the start/resume light flashing. When I opened the door and hit cancel, the unit turned off. Several minutes later, the normal light and heated dry lights came on, and soon after, the unit started up by itself (Twilight Zone music is going off in my head). I let it continue to see what it was going to do. It ran, and ran, and ran some more. I stopped it and secured the power to it, left the power off for a very long time. Started it up, no joy.I began reading the blogs sent in by other frustrated Maytag owners, we are numerous. I went back and re-read some of the posts that dealt with resetting the control panel. The one that mentioned; press Hi Temp. then Start/Resume about 3 times consecutively, that did the trick. Thank you for that useful piece of info. Saved me 143.00 plus tax and shipping for the new control panel (for now). I found some very helpful MOs (Maytag owners). I also found something very frustrating, with so many unhappy customers dealing with the similar issue. I would think that Maytag would put out a technical alert that deals with these problems. Instead, we get these so-called Maytag experts that magically appear on your computer screen. They ask you, what seems to be the problem. So after I described the issue, I asked the Pro, how to prove that the issue is with the control panel, or the elect. control board, both parts are 143.00 ea. (Just trying to limit my pain.) They send me to a page that wants to charge me 28.00 for the answer. What an insult. We pay 500-800 dollars for these units that should last more than 4 yrs. and some doofus is charging you for answers that saves you the consumer money and frustration. I, like many in the Maytag blog, will never purchase a Maytag product again.

Problems with Maytag dishwasher, purchased at Sears Canada Model MDB7749S is only a couple of years old, and as such is no longer under warranty. This Dishwasher is less than 3 years old! Both the interior and exterior is stainless steel and looks virtually new. Cost of parts and labour to repair amount to more than a new dishwasher--this is unacceptable. Poor design. Little value compared to cost. First issue: bottom rack wheels fall off because the plastic pin holding the plastic wheels on the rack become fall out, leaving no way to hold the wheels onto the rack. Second issue: faulty design of the integrated door handle and control panel on the exterior door face. The control panel pops out of the front cover panel when door is pulled open. With some struggle it can be popped back in.I agree with another reviewer who wrote: The design of the faceplate is defective in that too much force is applied to the faceplate when opening the unit. The handle is integrated in to the faceplate. The plastic used becomes brittle over time and breaks. The panel unit (W10811169) must be replaced in entirety rather than just its housing increasing the cost of repair. To have this failure occur within the first 3 years of use is very premature. I can only assume if I repair the dishwasher I will have the same problem again. I am considering buying a new model that is designed better and comes with a longer warranty on such parts.

Replacing a working but noisy 14 year old Sears dishwasher for the newer Maytag was my bone head move for 2011. It died the first year control panel shot, no warranty. Paid for repair. This month dead again; same problem. Recall this stainless steel garbage. Maytag model MDBH949. Maytag, never again. Bought twice and last time.

In December of 2013, I purchased a Middle of the Line Maytag Dishwasher model #MDB8949SBW for $600 plus $200.00 for install and removal of 5 yr old Kenmore. At that time I thought I did my research and saw no major negative flaws on this type of machine or similar machines. This replaced a 5 yr old low line Kenmore that just upped and died. Installed just before the holidays, this Maytag machine seemed to have worked tirelessly until a few days ago August 18/2015. The computer controls went haywire. I was hitting normal start buttons and other buttons on the other side of the control panel were blinking and lighting up. Worse was trying to cancel and the control boards were not responding. Even hitting the start button, the machine would not turn on. Finally looking at the facia, I see the tabs of the flexible plastic frame that hold the control panel popping out from underneath the white facia plate. Snapping the frame back in and applying a lot of pressure got the machine to operate. With a family of four and minimal storage space, this machine is used approx once a day. It appears over the year and 1/2 by pulling on the plastic handle - which also happens to be the computer control board frame, the computer has separated from its mount and has allowed moisture to hit the control board/computer and wreak havoc on the electronics. Looking up this model online NOW, I see I am not the only one with Dishwasher computers failing within a year or two- just out of the one year warranty. A Call to Maytags customer service has the computer control board alone cost $160.00 plus the service tech and his labor fees reaching in excess of $450.00. The CS rep gave me a repair discount to $267.00 and a week wait for the Service Tech for this problem to be fixed. I bought this machine on two premises - one for its price, it was the only machine that offered 3 spin jets that really do a good job in cleaning dishes and 2, I owned a 1984 Maytag dishwasher in another home with computer controls in the handle and to this day, that machine is still running flawlessly! My only issue with the 84 Maytag machine was after 4 years the door gasket went - too much soap - replaced and no issues since! I expected similar performance with this one. I guess I have to spend north of 3 bills for similar performance and quality. What was I thinking?

Our 3-year-old Maytag Quiet Series 300 dishwasher continues to have problems, especially with electronic keypad, which we had replaced (exactly) 1 year ago. The issues are: currently (and previously) not filling water; leakage around gasket, which we replaced twice. I read in other related posts that fire hazard has been flagged as a potential problem. Im not surprised as I cant tell you how many times this machine has gone through the motions (cycles) of appearing to clean, then we discovered that it has not cleaned anything, despite being very hot (and dry) inside the unit. Stay away from this brand.Multiple service calls and replacement parts we incurred at our own cost, in addition to many episodes of inconvenience to our family.

Most American dishwashers are made by Whirlpool. My control panel failed after only 3 years (design is terrible!). I had to pay almost 50% of original dishwasher cost to have it replaced by Factory Service Co. (formerly Whirlpool service).

When purchasing new, sales person highly recommended Maytag products. Maytag Dishwasher MDB7749SBW3 - This had the SS tub that my wife was looking for. Now only 19 months later it has completely stopped working. A few weeks ago the lights on the control panel would randomly come on or not align with the wash option that was chosen. This lasted a short time, and then lights on the panel would stay on, and not allow you to choose any options. I reset our breaker and this alleviated the problem for another week or so. Then it stopped working all together. A quick Google search and it was obvious Maytag has a MAJOR and KNOWN issue with this model. The ribbon going into the faceplate/ control board sits directly behind the port that exhausts the steam. This ribbon over time becomes corroded and eventually malfunctions. I called customer support. They were completely unwilling to acknowledge the problem and also unwilling to help in any way. They offered to sell me an extended warranty @ $329.00 that would cover the service call and repair. Very unhappy that their product has an obvious defect/ flaw and they are completely unwilling to acknowledge/ or stand behind their product. We are a family of (3) and run this dishwasher about once every 5-10 days. Unbelievable they find a fail rate within a year and half with light use acceptable!

We bought what was supposed to be the top of the line Maytag dishwasher as part of a kitchen remodel in 2011. Well tonight it has quit working for the 3rd time! I think this is the last straw for us! Tired of spending all this money having it fixed. We also bought a Maytag microwave at the same time that has been nothing but trouble from day 1, but not as bad as the dishwasher. I can promise you we will never buy another Maytag product ever. Heck at this point, I would not accept a free Maytag machine of any kind! Stay away from Maytag!! Just to be more specific, the first time the dishwasher quit it was the board and cost us half as much as the dishwasher. I see lots of mentions of boards going out early.

We purchased this set 6 months ago. The store we purchased it from is unwilling to help us. Maytag insists there is nothing wrong with the washing machine. The machine doesnt clean the clothes. After a wash cycle there is pet fur and lint all over the clothes, even after it comes out of the dryer. The clothes are all twisted in tight knots when the load is done. The washing Machine doesnt dispense enough water to wash. I have taken clothes out of the washer and the items are dry in spots, most times you can smell the mustiness of a dish towel after its been washed.I used the steam clean dryer to fresh in up the curtains and the panels came out different lengths. Not eager to try that feature again. This is our 2nd dryer set purchase, the last set was 10 yrs old. I couldnt find anyone willing to repair it. I was told they dont make machines like they used to and they are all designed to last 10 yrs and you’re lucky if it lasts 15 yrs. Yes, we contacted Maytag and yes, like the many other folks who have shared their stories we also got the run around. Sad to say we are going to do our research and will be looking for a new machine. Im going to shamefully donate the set to a charitable organization and use the receipt as a tax write off. IF you’re doing your research, DO NOT BUY A MAYTAG.

I am a WWII vet. I bought a Maytag dishwasher 4 years ago from Home Depot... Cost me $600 in total repairs. Maytag would not help. My son just brought it to the dump! At that same time I bought a Maytag bottom freezer from Home Depot... It has never worked right. Ice dispenser broken after 1 year, food freezing in fridge at any temperature... It just died! Maytag refuses to take any responsibility for THIS POS!They should be ashamed at the way they treated me. I am 94 years old, and have fought for our freedom, and was looking for one simple thing from this American company. Its called fairness! Maytag sucks! You have lost a lifetime customer. You have lost my son as a customer, and will lose anyone I talk to, as well as my son posting on ALL social media! SHAME ON YOU MAYTAG! SHAME ON YOU MAYTAG!

Maytag dishwasher mdbh979sam1 - Every single one of the Maytag/whirlpool dishwashers with soft pushbuttons and LEDs will fail--check it on YouTube. They have a very thin printed circuit strip from the door controller to the brains, and this rusts through in a few years. You must buy the whole controller for $150, you cant replace just the ribbon. And youll be doing this every few years. Maytag disavows this if you call them. The design runs the steam past this ribbon, so it corrodes really fast. Get a real pushbutton or a real dial knob model instead. With this model, the issue shows up when the LED pushbuttons stop responding or randomly light.

My Maytag dishwasher which is less than 2 yrs old had its control panel and board gone bad. It took almost $400 to fix it. It seems like an ongoing problem and Maytag does not do anything. I would have bought a new dishwasher for that price, but I was already in for almost $200.00. They dont give you prices upfront.

I have been washing clothes in different washers for almost 4 decades and never had a terrible washer until now. It has total control of the water level and it NEVER has enough water added. I have to add at least 2 full dish pans of water to every load. My washer does not allow you to pick your level because it does it automatically and no theres way to bypass this problem. It moans and groans for almost an hour in slow motion at its best. It should be illegal to sell such crap!If the intent was to save energy it fails when it runs twice as long as other washers. The instructions that are in the lid say that when you set it on deep water wash that it does not sense automatically-LIES! This lid must be generically made for other washers that they have because again, you cannot choose a water level. When a washer runs for almost an hour (this is not soak or extra rinse either) it is not saving energy over those that run for half that length of time. I wish I had returned it, but I listen to others who say that this is how washers are now. I still owe 150.00 on it and hate writing that check.

Maytag Bravos XL Washer and Dryer. How exciting to get a new washer/dryer!! Im a savvy bargain and quality shopper, but I really messed up here. A little over a year ago, we moved from IL back to TX and I got to buy a new washer AND dryer at the same time (a rarity). I went and looked at SO many washers/dryers and decided on the Maytag Bravos XL because a friend said she loved hers. It had a deep water wash and bedding cycle (for our blankets, comforters, sleeping bags, etc), and I thought that I could throw that wayward sock in after I started the load (unlike our previous front load washer).Where do I begin with the complaints? (And Im NOT a complainer - never filled out a review in my life). This is what I sent to Maytag: 1) Im 55 tall and can barely reach the items at the bottom of the drum, along with the lid falling on my head when Im trying to do so. 2) Forget throwing in the wayward sock - it must finish the cycle its in before it will let you unlock the lid (Where did locked lids come from anyway? Is that how those missing socks are disappearing - escaping out of unlocked lids? What are we trying to keep in or who are we trying to keep out of the machine? Doors you lock - not washing machines! I dont get it!).3) Even the deep water/bedding wash cycle does not do the job. Using the exact recommended measurement of HE liquid soap does not get the items clean. What a chore to take something out and have white detergent lines all over it and have to wipe it down with a wet cloth. Sure, I could then do a rinse and spin cycle, but since it doesnt add enough water, it doesnt come out much better. The machine senses by weight how much water to use. I am positive that every energy efficient machine is now programmed to add exactly 4 cups of water per load (regardless if its a comforter or one pair of jeans).4) Supposedly, we are saving so much water usage, but energy efficient is a misnomer - it takes me twice as long to do laundry now. The time factors are ridiculous. There are no quick cycles on this machine. If I have a load of delicate tops that just need a quick wash and rinse before I hang them out (I was not out baling hay in them, so its not like they are filthy dirty. In Texas, its the sweat that you are trying to eliminate), the least amount of time I can find on a cycle is 45 minutes. I might as well hand wash them all and be done in 5 minutes. But, that was the point of the washing machine - to do the work for me! And forget the deep water wash cycle of 58 minutes, plus the added rinse and spin cycle (to try and remove the white soap line). Its now taken one and one-half hours to try and clean/refresh a barely soiled comforter.5) The spin cycle is SO efficient, that I have items come out totally dry many times in certain spots. Im washing a comforter right now and I can guarantee you that when I remove it from the washer, there will be an entire section that looks like it never even got wet. Im no engineer, but after watching through the see-through lid, the agitation is not working well enough to get to every section.6) I havent seen a soap bubble or suds yet. You are told to use such a small amount of detergent, Im not sure how anything actually gets clean. The clothes are sprinkled with water, agitated a small amount, spun until they are almost dry and voila - the same dirty clothes come out! 7) The dryer has now ruined 2 of my bras as the hooks get caught in the mesh panel at the back. It literally melted part of the bra! I tried hooking them together before I threw them in there, but now have to put them in a lingerie bag to keep them from being mauled and mutilated. I have NEVER in 37 years of marriage and washing had that happen before.8) I literally could not get my dryer to turn on and a repairman had to come out to the house to show me the amount of pressure I had to use in one finger to start the dryer. I had almost taken a hammer to it before he arrived. Can you imagine pressing the start button on anything - the dishwasher, a hair dryer, a TV remote control, and it not turning on? And all because you pressed too hard or too light? This computer age and electronic panels are killing me! 9) The dryer has the same locking system as the washing machine. So, if you didnt see the wayward sock on the floor or between the two units until after you pushed (lightly, of course) the start button, you have to stop the unit before you can open the door to throw the sock in.I didnt mean to write a novel (about a washer and dryer, no less)! But, I feel better and hope that I have saved one woman from making the same mistake I did. Read those reviews AND believe them. And by the way, my friend who recommended the Bravos XL to me looked at mine and said Thats NOT my washer and dryer. Evidently, mine was the new and improved version! So much for that claim!

Purchased this dishwasher 3 1/2 yrs. ago. Control panel went out. We would have had to pay almost the cost of new one to replace the part! Maytag used to be reliable. The dishwasher we owned previously (not Maytag) was still working after 12 years!

Bought Maytag dishwasher model number MDB894995BB3 serial # F41103073. About 2 months out of warranty the control panel went bad. Contacted Maytag. After quite some time they agreed to pay for parts. After some more conversation they also agreed to pay service and labor. This was on the first day of August and Maytag scheduled a repairman for the sixth of August. When he arrived spent five minutes and said he had to order parts. The control panel I had already told them was bad. Now here I sit waiting for part to arrive. No more Maytag or Whirlpool for me.

On February 2006, I purchased a Maytag Quiet Series 300 Dishwasher and on July 2007, a motor leak. Maytag fixed it for free even though it was out of warranty. Thereafter (December 2008), the touch pad failed and I replaced it for $50. It is now August 2011, and that new touch pad is bad again, and this time, the part is $170. The Maytag will not run and the lighted display will not function from the start button. This was a $450 dishwasher that is now only five years old and useless.In all fairness to Maytag, their customer service is very good and willing to work with customers. Unfortunately, the product is very inferior in my opinion. To have stupid stuff like a control touch pad failing every three years is absurd and the replacement cost makes fixing it a bad investment.I will be going out this weekend and buying a brand-new inexpensive dishwasher that is on sale for $229. This model is not a Whirlpool product but it is a name brand.

13 months after purchasing my Maytag dishwasher, it started operating by itself. I woke up one morning around 2:00 to it working, and I know I didnt put it on! I only use the auto clean cycle (that decides how dirty the dishes are, and is the cycle you use to conserve water). I dont use heat dry at all. Anyway, now I go to use the dishwasher and even though I press the auto clean button, the normal/heat dry/delay start buttons flash on. I try canceling this cycle out; sometimes it works, sometimes it doesnt. I dont see Maytag as reliable anymore.

I have had this dishwasher less than 2 years, Maytag model # MDB7749SBM2. The control panel started acting up, it would not let me select a wash cycle, it would select its own and I could not change it. After reading these reviews, I took off the control panel and discovered the wires which are encased in a plastic were all darkened and messed up. I will try to replace it on my own but if I have to I will buy another brand as this dishwasher hasnt really cleaned my dishes all that well to begin with.

There was a maytag dishwasher in the house we bought 11 yrs ago. The only problem we have had is a recall on the rinse aid dispenser which was replaced by a service man but never worked again. We are completely satisfied with the operation of the unit, our only disappointment is the wire racks. The original racks plastic coating broke at the end nubs and became rusty and swollen. We found someone selling a unit and we just took the racks and left the unit for him to resell rackless. Unfortunately not two yrs later the same thing has happened to those racks. Even tried these little plastic covers that are made specifically for this problem. They were virtually impossible to get on and didn’t last more than a few months.

Bought a Maytag dishwasher early July. Worked great for 3 months. Drain pump went out. Called customer service, 30 minutes to get a person. 1 week to get a service tech here. Even though we told them pump was out. Sent with no repair parts. So has to come back at our inconvenience, company policy, not service tech fault. Tried to complain on live chat. 30 minutes for them to get with me. Still no satisfaction. Would not recommend the product for the company itself. Sadly thought we upgraded.

We bought a Maytag dishwasher in August, 2014, and already the touchpad is malfunctioning and we cant start the dishwasher! I am very disgruntled and frustrated by this! I should have kept the old Kitchen Aid dishwasher that we bought in 1995! At least it never malfunctioned!

I will never buy another Maytag product, and moreover, will tell everyone I possibly can, not to do so either. Like many others, I have a two-year-old dishwasher that needs a control board already, and from what Ive read this wont be the first time. It would cost $150 for the part, plus the service calls make it around a $350 experience. The only choice is to pull the machine out, or buy a 5-year warranty for another $318.56. Grand total for your marvelous high quality Maytag that lasts only 7 years? Around $1,000. I am so sad, the company used to symbolize quality but now when I see the logo, I think of landfills.

Ive had other dishwashers over the years. Ive had this Maytag now for almost 12 years and never had a problem with it. It cleans better than any others Ive owned. HIGHLY recommend the Maytag.

I purchased a Maytag dishwasher Model # MDB4949SDE1 from Home Depot April 30th 2015. This dishwasher does not clean the dishes no matter what cycle you use. After 4 hours and 29 minutes I open the dishwasher to find residue on my so-called clean dishes. Every time I use it I have to re-wash or rinse the dishes by hand before I can put them away.I have spoken with Maytag on several occasions concerning this matter. I have used every detergent on the market. Maytag says you have to use jetdry, and liquid detergent which I did and it made no difference. The latest suggestion was that the water from my water heater was not hot enough which is set on 140 degrees. The customer service rep. ask me how far the water heater is from the dishwasher and I replied approximately 14 foot. She suggested I turn the faucet to my sink on before I turn the dishwasher on so that the hot water is present as soon as I turn it on. This also did not work. They sent a kid out today that turn the dishwasher on for five minutes empty and said well everything seems to be working properly. I dont know what to tell you, yet there is soap residue in the bottom of the dishwasher right now. Do not purchase this dishwasher. It does not clean the dishes. It just uses power and water.

I purchased our Maytag dishwasher last November. Last week, the control panel went out. I called customer service and they were actually polite and helpful, except for the fact that I had to wait an entire week to have a technician come to my house. Being that I live in the Balt/DC Metro area, I would have thought they would have enough people in the area to come over faster. Anyhow, we finally had the technician come today and tell us that the control panel needs replaced and that he highly recommends an extended warranty, which costs $200 for 5 years. He let my husband know that the repair itself would cost $500 if not covered by warranty!!! What a ripoff! I purchased this dishwasher because I grew up believing in the Maytag brand. Sounds like this is an extremely common issue and if Maytag wants to make things right, they should discontinue sale of their crap product and provide those of us who are stuck with it, a complimentary 5 year warranty. I shouldnt have to pay $200 in extended warranty to make up for the fact that my control panel is likely to go out again in another year, when Ill be forced to buy a new dishwasher.

We bought a Maytag dishwasher (Model: MDBH979AWS3) in January 2010. In April 2012, the control panel stopped working. A local repairman came out to see it for $160, diagnosed it, and suggested that we call Maytag to see if they would give us the part because it was only a two-year old machine. He did say that the control panel was not a part that was troublesome!Maytag offered an extended warranty for only $287 that would cover the part! The total repair cost was almost equal to the cost of a new machine. Home Depot, when consulted, acted as if they know nothing. After reading about other peoples experiences with this company, I feel that it is no longer an honorable company standing behind its products. In fact, the whole repair process is set up to rip off the consumer.We will now look to purchase the best and cheapest non-Maytag product, not from Home Depot, and throw it away when it gives out, which more than likely will be soon. These companies have finally convinced me to do what I am sure what they have always wanted every consumer to do. Throw it away when it breaks down.

I love my dishwasher. The only hold back is similar to what I hear about all others and that is that it takes a long time. I love that is it quiet, has lots of room and is easy to use.

Our Maytag dishwasher is a work horse. Never a problem just runs and runs. Could be a little quiet quieter. But does a t great job cleaning. I would definitely buy another one and would recommend it to any one.

I bought my Maytag Quiet Series 300 about 6 or 7 years ago. About January this year the clean light quit working but the dishwasher was still doing its job. Every once in a while the clean light would come on again and then go away. I did not worry about this as the dishwasher was still working despite the absent clean light. I did call Maytag and told them about this. I believe I even asked if they (customer service rep.) had heard about this and was told no. Last Friday the start button no longer works which means the dishwasher will not function. Some of the other lights/buttons work but not start or clean. I have dealt with Maytag repair service/customer service before about my Maytag washer. I know they are not much help and I always end up paying a lot of money. I am not interested in calling a Maytag repair person in and paying from what 300.00 to 400.00 dollars to get it fixed. Past experience of others seem to prove that it will break down again. Last Maytag appliance that I will ever buy. I used to be a loyal customer. I want to join the class action suit. Please tell me how I can join.